1776537中文资料

合集下载

1730117资料

Extract from the onlinecatalogMKDSP 1,5/12Order No.: 1730117The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1730117Printed circuit terminal block, nominal current: 17.5 A, rated voltage: 250 V, pitch: 5.0 mm, no. of positions: 12, mounting: Soldering, type of connection: Screw connection, connection direction from the conductor to the PCB: 0°http://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch 5 mmDimension a60 mmNumber of positions12Pin dimensions0,9 x 0,9 mm Hole diameter 1.3 mm Screw thread M 3 Tightening torque, min0.5 NmTechnical dataInsulating material group IRated surge voltage (III/3) 4 kVRated surge voltage (III/2) 4 kVRated surge voltage (II/2) 4 kVRated voltage (III/2)320 V Rated voltage (II/2)630 V Connection in acc. with standard EN-VDE Nominal current I N17.5 A Nominal voltage U N250 V Nominal cross section 1.5 mm2 Maximum load current22 A Insulating material PA Inflammability class acc. to UL 94V0Internal cylindrical gage A1 Stripping length7 mmConnection dataConductor cross section solid min.0.14 mm2 Conductor cross section solid max. 2.5 mm2 Conductor cross section stranded min.0.14 mm2 Conductor cross section stranded max. 1.5 mm2 Conductor cross section stranded, with ferrule0.25 mm2 without plastic sleeve min.Conductor cross section stranded, with ferrule1.5 mm2 without plastic sleeve max.Conductor cross section stranded, with ferrule0.25 mm2 with plastic sleeve min.Conductor cross section stranded, with ferrule1.5 mm2 with plastic sleeve max.Conductor cross section AWG/kcmil min.26 Conductor cross section AWG/kcmil max142 conductors with same cross section, solid min.0.14 mm22 conductors with same cross section, solid max. 1 mm22 conductors with same cross section, stranded0.14 mm2min.2 conductors with same cross section, stranded0.75 mm2max.2 conductors with same cross section, stranded,0.25 mm2ferrules without plastic sleeve, min.2 conductors with same cross section, stranded,0.5 mm2ferrules without plastic sleeve, max.2 conductors with same cross section, stranded,0.5 mm2TWIN ferrules with plastic sleeve, min.2 conductors with same cross section, stranded,1 mm2TWIN ferrules with plastic sleeve, max.Certificates / ApprovalsCSANominal voltage U N300 VNominal current I N10 AAWG/kcmil28-14CULNominal voltage U N300 VNominal current I N10 AAWG/kcmil30-14ULNominal voltage U N300 VNominal current I N10 AAWG/kcmil30-14Certification CB, CCA, CSA, CUL, GOST, SEV, ULAccessoriesItem Designation DescriptionGeneral1733169EBP 2- 5Insertion bridge, fully insulated, for plug connectors with 5.0 or5.08 mm pitch, no. of positions: 21718207ST-MKDSP 3/5Test connector, 5-pos., with 2 mm test pins, gold-plated test pinsMarking0804183SK 5/3,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 12 identicaldecades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for120 terminal blocksPlug/Adapter0201744MPS-MT Test plug, consisting of: Metal part for 2.3 mm diameter sockethole0201647RPS Reducing plug, for transition from 4 mm diameter test plug socket,insulation: gray1301355SPB 10-MKDSP Test plug, 10-pos., with 2 mm lamellar pins and 10 firmly welded 1m test conductors, gold-plated lamellar pinsTools1205053SZS 0,6X3,5Screwdriver, bladed, matches all screw terminal blocks up to 4.0mm² connection cross section, blade: 0.6 x 3.5 mm, without VDEapprovalDrawingsDrilling diagramDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。

1755503中文资料

Extract from the onlinecatalogMSTBVA 2,5/10-GOrder No.: 1755503The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1755503Header, nominal current: 12 A, rated voltage: 250 V, pitch: 5.0 mm, no. of positions: 10, mounting: Solderinghttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch 5 mmNumber of positions10Pin dimensions 1 x 1 mmHole diameter 1.4 mmTechnical dataInsulating material group IIIaRated surge voltage (III/3) 4 kVRated surge voltage (III/2) 4 kVRated surge voltage (II/2) 4 kVRated voltage (III/2)320 VRated voltage (II/2)400 VConnection in acc. with standard EN-VDENominal current I N12 ANominal voltage U N250 VMaximum load current12 AInsulating material PBTInflammability class acc. to UL 94V0Certificates / ApprovalsCSANominal voltage U N300 VNominal current I N10 ACULNominal voltage U N300 VNominal current I N10 AULNominal voltage U N300 VNominal current I N10 ACertification CB, CSA, CUL, GOST, UL, VDE-PZIAccessoriesItem Designation DescriptionAssembly1755477MSTB-BL Keying cap, for forming sections, plugs onto header pin, greeninsulating materialMarking0804183SK 5/3,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 12 identicaldecades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for120 terminal blocksPlug/Adapter1734401CR-MSTB Coding section, inserted into the recess in the header or theinverted plug, red insulating materialAdditional productsItem Designation DescriptionAssembly1909294FKCT 2,5/10-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 10, type of connection: Spring-cage connectionGeneral1910432FKC 2,5/10-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 10, type of connection: Spring-cage connection1909799FKCVR 2,5/10-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 10, type of connection: Spring-cage connection1910115FKCVW 2,5/10-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 10, type of connection: Spring-cage connection1779495FRONT-MSTB 2,5/10-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 10, type of connection: Screwconnection1754601MSTB 2,5/10-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 10, type of connection: Screwconnection1759004MSTB 2,5/10-STZ Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 10, type of connection: Screwconnection1765852MSTBP 2,5/10-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 10, type of connection: Screwconnection1779916MSTBT 2,5/10-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 10, type of connection: Screwconnection1792090MVSTBR 2,5/10-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 10, type of connection: Screwconnection1792605MVSTBW 2,5/10-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 10, type of connection: Screwconnection1768833SMSTB 2,5/10-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 10, type of connection: ScrewconnectionDrawingsDrilling diagramDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。

1945753资料

PHOENIX CONTACT GmbH & Co. KG http://www.phoenixcontact.de
Page 3 / 3 Mar 8, 2008
Address
ቤተ መጻሕፍቲ ባይዱ
PHOENIX CONTACT GmbH & Co. KG Flachsmarktstr. 8 32825 Blomberg,Germany Phone +49 5235 3 00 Fax +49 5235 3 41200 http://www.phoenixcontact.de
© 2008 Phoenix Contact Technical modifications reserved;
Page 1 / 3 Mar 8, 2008
元器件交易网
MCVR 1,5/ 3-STF-3,81 BK Order No.: 1945753
http://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1945753
Approval logo
CSA Nominal voltage UN Nominal current IN AWG/kcmil CUL Nominal voltage UN 300 V 300 V 8A 28-16
PHOENIX CONTACT GmbH & Co. KG http://www.phoenixcontact.de
Product notes Commercial data EAN Pack Customs tariff Weight/Piece 4017918864101 50 Pcs. 85366990 0.00357 KG http:// Please note that the data given here has been taken from the online catalog. For comprehensive information and data, please refer to the user documentation. The General Terms and Conditions of Use apply to Internet downloads. Certificates / Approvals WEEE/RoHS-compliant since: 01/01/2003

1755273资料

Extract from the onlinecatalogMSTBV 2,5/ 5-G BKOrder No.: 1755273http://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1755273Header, nominal current: 12 A, rated voltage: 250 V, pitch: 5.0 mm, no.of positions: 5, mounting: Solderinghttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Certificates / ApprovalsApproval logoCSANominal voltage U N300 VNominal current I N10 ACULNominal voltage U N300 VNominal current I N10 AULNominal voltage U N300 VNominal current I N10 ACertification CB, CSA, CUL, UL, VDE-PZIAccessoriesItem Designation DescriptionAssembly1755477MSTB-BL Keying cap, for forming sections, plugs onto header pin, greeninsulating materialMarking1051993B-STIFT Marker pen, for manual labeling of unprinted Zack strips,smear-proof and waterproof, line thickness 0.5 mm0804183SK 5/3,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 12 identicaldecades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for120 terminal blocks0805072SK 5/3,8:SO Marker card, special printing, self-adhesive, labeled acc. tocustomer requirements, 12 identical marker strips per card, max.25-position labeling per strip, color: white0805409SK 5/3,8:UNBEDRUCKT Marker cards, unprinted, with pitch divisions, self-adhesive,10-section marker strips, 12 strips per card, can be labeled withthe M-PENPlug/Adapter1734401CR-MSTB Coding section, inserted into the recess in the header or theinverted plug, red insulating materialAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。

1730760资料

元器件交易网
Extract from the online catalog
MSTB 2,5/ 4-ST BD:4-1
Order No.: 1730760
http://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1730760
Product notes Commercial data EAN Pack Customs tariff Weight/Piece 4046356154970 50 Pcs. 85366990 0.00704 KG http:// Please note that the data given here has been taken from the online catalog. For comprehensive information and data, please refer to the user documentation. The General Terms and Conditions of Use apply to Internet downloads. Certificates / Approvals WEEE/RoHS-compliant since: 09/12/2006
PHOENIX CONTACT GmbH & Co. KG http://www.phoenixcontact.de
Page 3 / 3 Jul 16, 2008
Page 2 / 3 Jul 16, 2008
元器件交易网
MSTB 2,5/ 4-ST BD:4-1 Order No.: 1730760
http://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1730760

X9315WMIZ-2.7T1中文资料

®X9315Low Noise, Low Power, 32 TapsDigitally Controlled Potentiometer (XDCP™)The Intersil X9315 is a digitally controlled potentiometer (XDCP). The device consists of a resistor array, wiper switches, a control section, and nonvolatile memory. The wiper position is controlled by a 3-wire interface.The potentiometer is implemented by a resistor array composed of 31 resistive elements and a wiper switching network. Between each element and at either end are tap points accessible to the wiper terminal. The position of the wiper element is controlled by the CS, U/D, and INC inputs. The position of the wiper can be stored in nonvolatilememory and then be recalled upon a subsequent power-up operation.The device can be used as a three-terminal potentiometer or as a two-terminal variable resistor in a wide variety of applications including:•Control•Parameter Adjustments •Signal ProcessingFeatures•Solid-state potentiometer •3-wire serial interface•32 wiper tap points-Wiper position stored in nonvolatile memory and recalled on power-up •31 resistive elements-Temperature compensated-End to end resistance range ± 20% -Terminal voltage, 0 to V CC •Low power CMOS -V CC = 2.7V or 5V-Active current, 50/400µA max.-Standby current, 1µA max.•High reliability-Endurance, 100,000 data changes per bit -Register data retention, 100 years •R TOTAL values = 10k Ω, 50k Ω, 100k Ω•Packages-8 Ld SOIC, MSOP and PDIP•Pb-free plus anneal available (RoHS compliant)Block DiagramH /V HL /V L W /V WUp/Down(U/D)Increment(INC)(CS)V (Supply Voltage)SS R H /V HR W /V R L /V LGeneralDetailedOrdering InformationPART NUMBER PART MARKING V CC LIMITS(V)R TOTAL(kΩ)TEMP RANGE(°C)PACKAGEX9315WM*AAW 5 ±10% 100 to 708 Ld MSOPX9315WMZ* (Note)DDT0 to 708 Ld MSOP (Pb-free) X9315WMI*AAX-40 to 858 Ld MSOPX9315WMIZ* (Note)AKW-40 to 858 Ld MSOP (Pb-free) X9315WP X9315WP0 to 708 Ld PDIPX9315WPI X9315WP I-40 to 858 Ld PDIPX9315WS*X9315W0 to 708 Ld SOICX9315WSZ* (Note)X9315W Z0 to 708 Ld SOIC (Pb-free) X9315WSI*X9315W I-40 to 858 Ld SOICX9315WSIZ* (Note)X9315W Z I-40 to 858 Ld SOIC (Pb-free) X9315UM*500 to 708 Ld MSOPX9315UMZ* (Note)DDS0 to 708 Ld MSOP (Pb-free) X9315UMI*AEB-40 to 858 Ld MSOPX9315UMIZ* (Note)DDR-40 to 858 Ld MSOP (Pb-free) X9315UP X9315UP0 to 708 Ld PDIPX9315UPI X9315UP I-40 to 858 Ld PDIPX9315US*X9315U0 to 708 Ld SOICX9315USZ* (Note)X9315U Z0 to 708 Ld SOIC (Pb-free) X9315USI*X9315U I-40 to 858 Ld SOICX9315USIZ* (Note)X9315U Z I-40 to 858 Ld SOIC (Pb-free) X9315TM*AEJ1000 to 708 Ld MSOPX9315TMZ* (Note)DDN0 to 708 Ld MSOP (Pb-free) X9315TMI*ADZ-40 to 858 Ld MSOPX9315TMIZ* (Note)DDL-40 to 858 Ld MSOP (Pb-free) X9315TP X9315TP0 to 708 Ld PDIPX9315TPI X9315TP I-40 to 858 Ld PDIPX9315TS*X9315T0 to 708 Ld SOICX9315TSZ* (Note)X9315T Z0 to 708 Ld SOIC (Pb-free) X9315TSI*X9315T I-40 to 858 Ld SOICX9315TSIZ* (Note)X9315T Z I-40 to 858 Ld SOIC (Pb-free)X9315TP-2.7X9315TP F 2.7-5.5100 to 708 Ld PDIP X9315TPI-2.7X9315TP G -40 to 858 Ld PDIP X9315WM-2.7*AAU 0 to 708 Ld MSOPX9315WMZ-2.7* (Note)AOI 0 to 708 Ld MSOP (Pb-free)X9315WMI-2.7*AAV-40 to 858 Ld MSOPX9315WMIZ-2.7* (Note)-40 to 858 Ld MSOP (Pb-free)X9315WP-2.7X9315WP F 0 to 708 Ld PDIP X9315WPI-2.7X9315WP G -40 to 858 Ld PDIP X9315WS-2.7*X9315W F 0 to 708 Ld SOICX9315WSZ-2.7* (Note)X9315W Z F 0 to 708 Ld SOIC (Pb-free)X9315WSI-2.7*X9315W G -40 to 858 Ld SOICX9315WSIZ-2.7* (Note)X9315W Z G -40 to 858 Ld SOIC (Pb-free)X9315UM-2.7*AEK 500 to 708 Ld MSOPX9315UMZ-2.7* (Note)AKU 0 to 708 Ld MSOP (Pb-free)X9315UMI-2.7*AEA -40 to 858 Ld MSOPX9315UMIZ-2.7* (Note)AJG-40 to 858 Ld MSOP (Pb-free)X9315UP-2.70 to 708 Ld PDIP X9315UPI-2.7-40 to 858 Ld PDIP X9315US-2.7*X9315U F 0 to 708 Ld SOICX9315USZ-2.7* (Note)X9315U Z F 0 to 708 Ld SOIC (Pb-free)X9315USI-2.7*X9315U G -40 to 858 Ld SOICX9315USIZ-2.7* (Note)X9315U Z G -40 to 858 Ld SOIC (Pb-free)X9315TM-2.7*AEI 1000 to 708 Ld MSOPX9315TMZ-2.7* (Note)DDP 0 to 708 Ld MSOP (Pb-free)X9315TMI-2.7*ADY -40 to 858 Ld MSOPX9315TMIZ-2.7* (Note)DDM -40 to 858 Ld MSOP (Pb-free)X9315TS-2.7*X9315T F 0 to 708 Ld SOICX9315TSZ-2.7* (Note)X9315T Z F 0 to 708 Ld SOIC (Pb-free)X9315TSI-2.7*X9315T G -40 to 858 Ld SOICX9315TSIZ-2.7* (Note)X9315T Z G-40 to 858 Ld SOIC (Pb-free)NOTE:Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.*Add "T1" suffix for tape and reel.Ordering Information (Continued)PART NUMBERPART MARKING V CC LIMITS(V)R TOTAL (k Ω)TEMP RANGE(°C)PACKAGEPin DescriptionsR H /V H and R L /V LThe high (R H /V H ) and low (R L /V L ) terminals of the X9315 are equivalent to the fixed terminals of a mechanical potentiometer. The minimum voltage is V SS and the maximum is V CC . The terminology of R L /V L and R H /V H references the relative position of the terminal in relation to wiper movement direction selected by the U/D input, and not the voltage potential on the terminal.R W /V WR W /V w is the wiper terminal and is equivalent to the movable terminal of a mechanical potentiometer. The position of the wiper within the array is determined by the control inputs. The wiper terminal series resistance is typically 200Ω at V CC = 5V.Up/Down (U/D)The U/D input controls the direction of the wiper movement and whether the counter is incremented or decremented.Increment (INC)The INC input is negative-edge triggered. Toggling INC will move the wiper and either increment or decrement the counter in the direction indicated by the logic level on the U/D input.Chip Select (CS)The device is selected when the CS input is LOW. The current counter value is stored in nonvolatile memory when CS is returned HIGH while the INC input is also HIGH. After the store operation is complete the X9315 will be placed in the low power standby mode until the device is selected once again.Pin ConfigurationPrinciples of OperationThere are three sections of the X9315: the input control, counter and decode section; the nonvolatile memory; and the resistor array. The input control section operates just like an up/down counter. The output of this counter is decoded to turn on a single electronic switch connecting a point on the resistor array to the wiper output. Under the proper conditions the contents of the counter can be stored innonvolatile memory and retained for future use. The resistor array is comprised of 31 individual resistors connected in series. At either end of the array and between each resistor is an electronic switch that transfers the connection at that point to the wiper.The wiper, when at either fixed terminal, acts like itsmechanical equivalent and does not move beyond the last position. That is, the counter does not wrap around when clocked to either extreme.The electronic switches on the device operate in a “make before break” mode when the wiper changes tap positions. If the wiper is moved several positions, multiple taps are connected to the wiper for t IW (INC to V W change). The R TOTAL value for the device can temporarily be reduced by a significant amount if the wiper is moved several positions.When the device is powered-down, the last wiper position stored will be maintained in the nonvolatile memory. When power is restored, the contents of the memory are recalled and the wiper is set to the value last stored.Instructions and ProgrammingThe INC, U/D and CS inputs control the movement of the wiper along the resistor array. With CS set LOW the device is selected and enabled to respond to the U/D and INC inputs. HIGH to LOW transitions on INC will increment or decrement (depending on the state of the U/D input) a five bit counter. The output of this counter is decoded to select one of thirty two wiper positions along the resistive array.The value of the counter is stored in nonvolatile memory whenever CS transitions HIGH while the INC input is also HIGH.The system may select the X9315, move the wiper and deselect the device without having to store the latest wiper position in nonvolatile memory. After the wiper movement is performed as described above and once the new position is reached, the system must keep INC LOW while taking CS HIGH. The new wiper position will be maintained untilPin NamesSYMBOL DESCRIPTION R H /V H High terminal R W /V W Wiper terminal R L /V L Low terminal V SS Ground V CC Supply voltage U/DUp/Down control inputV CC CS INC U/D R H /V H V SS12348765X9315DIP/SOIC/MSOPR L /V L R W /V WINC Increment control input CSChip Select control inputPin NamesSYMBOL DESCRIPTIONchanged by the system or until a power-up/down cycle recalled the previously stored data.This procedure allows the system to always power-up to a preset value stored in nonvolatile memory; then during system operation minor adjustments could be made. The adjustments might be based on user preference, system parameter changes due to temperature drift, etc...The state of U/D may be changed while CS remains LOW. This allows the host system to enable the device and then move the wiper up and down until the proper trim is attained.Symbol TableMode SelectionCS INCU/D MODEL H Wiper Up LL Wiper Down HX Store Wiper Position HX X Standby CurrentL XNo Store, Return to StandbyWAVEFORMINPUTS OUTPUTS Must be steady Will be steady May change from Lo w to High Will change from Lo w to High May change from High to Low Will change from High to Low Don’t Care:Changes Allowed Changing:State Not Known N/ACenter Line is High ImpedanceNotes:(1) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage = (V w(n)(actual) - V w(n)(expected)) = ±1 MlMaximum.(2) Relative linearity is a measure of the error in step size between taps = R W(n+1) - [R w(n) + Ml] = ±0.2 Ml.(3) 1 Ml = Minimum Increment = R TOT /31.(4) Typical values are for T A = 25°C and nominal supply voltage.(5) This parameter is periodically sampled and not 100% testedAbsolute Maximum RatingsRecommended Operating ConditionsTemperature under bias. . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C Storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Voltage on CS, INC, U/D, V H , V L andV CC with respect to V SS . . . . . . . . . . . . . . . . . . . . . . . -1V to +7V ∆V = |V H –V L |. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5V Lead temperature (soldering 10 seconds). . . . . . . . . . . . . . . .300°C I W (10 seconds). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±7.5mATemperature (Commercial) . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C Temperature (Industrial). . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C Supply Voltage (V CC ) (Note 4) LimitsX9315. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V ± 10%X9315-2.7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.7V to 5.5VCAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; the functional operation of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.Potentiometer Characteristics(Over recommended operating conditions unless otherwise stated.)SYMBOLPARAMETERTEST CONDITIONS/NOTES LIMITSMIN TYP MAX.UNIT End to end resistance tolerance±20%V VH V H terminal voltage 0V CC V V VLV L terminal voltage 0V CC V Power ratingR TOTAL ≥ 10k Ω10mW R W Wiper resistance I W = 1mA, V CC = 5V 200400ΩR W Wiper resistance I W = 1mA, V CC = 2.7V4001000ΩI WWiper current ±3.75mA Noise Ref: 1kHz -120dBV Resolution3%Absolute linearity (1)V w(n)(actual) - V w(n)(expected)±1MI (3)Relative linearity (2)V w(n + 1) - [V w(n) + MI ]±0.2MI (3)R TOTAL temperature coefficient ±300ppm/°CRatiometric temperature coefficient±20ppm/°C C H /C L /C WPotentiometer capacitancesSee circuit #310/10/25pFDC Electrical Specifications(Over recommended operating conditions unless otherwise specified.SYMBOL PARAMETERTEST CONDITIONSLIMITSUNIT MINTYP (4)MAX I CC1V CC active current (Increment)CS = V IL , U/D = V IL or V IH and INC = 0.4V @ max. t CYC50µA I CC2V CC active current (Store) (EEPROM Store)CS = V IH , U/D = V IL or V IH and INC = V IH @ max. t WR 400µA I SB Standby supply currentCS = V CC - 0.3V, U/D and INC = V SS orV CC - 0.3V 1µA I LI CS, INC, U/D input leakage current V IN = V SS to V CC±10µA V IH CS, INC, U/D input HIGH voltage V CC x 0.7V CC + 0.5V V IL CS, INC, U/D input LOW voltage -0.5V CC x 0.1V C IN (5)CS, INC, U/D input capacitanceV CC = 5V, V IN = V SS , T A =25°C, f = 1MHz10pFEndurance and Data RetentionPARAMETER MIN UNITMinimum endurance 100,000Data changes per bitData retention100YearsTest Circuit #1Test Circuit #2Circuit #3 SPICE Macro ModelTest Point V W /R WV H /R HV L /R LV SForceCurrentV L VWTest PointV H /R HV W /R W V L /R LC HC L R W10pF10pFR HR LR TOTALC W 25pFAC Conditions of TestInput pulse levels 0V to 3V Input rise and fall times 10ns Input reference levels1.5VAC Electrical Specifications(Over recommended operating conditions unless otherwise specified)SYMBOLPARAMETERLIMITSUNIT MIN TYP (6)MAXt Cl CS to INC setup 100ns t lD INC HIGH to U/D change 100ns t DI U/D to INC setup 2.9µs t lL INC LOW period 1µs t lH INC HIGH period1µs t lC INC Inactive to CS inactive 1µs t CPH CS Deselect time (NO STORE)100ns t CPH CS Deselect time (STORE)10ms t IW INC to Vw change 15µs t CYC INC cycle time4µs t R , t F (7)INC input rise and fall time500µs t PU (7)Power-up to wiper stable 5µs t R V CC (7)V CC power-up rate 0.250V/ms t WRStore cycle510msPower-up and Down RequirementsThere are no restrictions on the power-up or power-down conditions of V CC and the voltages applied to the potentiometer pins provided that V CC is always morepositive than or equal to V H , V L , and V W , i.e., V CC ≥ V H , V L , V W . The V CC ramp rate spec is always in effect.AC TimingNotes:(6)Typical values are for T A = 25°C and nominal supply voltage.(7)This parameter is not 100% tested.(8)MI in the A.C. timing diagram refers to the minimum incremental change in the V W output due to a change in the wiper position.Performance Characteristics (Typical)Typical NoiseCSINCU/DV Wt CIt IL t IH t CYCt IDDIt IWMI(8)t ICt CPHt Ft R10%90%90%(Store)0-10-20-30-40-50-60-70-80-90-100-110-120-130-140-150102030405060708090100Frequency (kHz)N o i s e (d B )110120130140150160170180190200Typical Rtotal vs. TemperatureTypical Total Resistance Temperature CoefficientTypical Wiper Resistance10000 9800960094009200900088008600840082008000R t o t a l-55-45-35-25-15-5515253545556575Temperature8595105115125C°-55-350-300-250-200-150-100-50-45-35-25-15-55152535TemperaturePPM455565758595105115125°C0100200300400R w (Ω)500600700800246810121416Tap1820222426283032V CC = 2.7VTypical Absolute% Error per Tap PositionTypical Relative% Error per Tap PositionApplications InformationElectronic digitally controlled (XDCP) potentiometers provide three powerful application advantages; (1) the variability and reliability of a solid-state potentiometer, (2) the flexibility of computer-based digital controls, and (3) the retentivity of nonvolatile memory used for the storage of multiple potentiometer settings or data.40.0%30.0%20.0%10.0%0.0%-10.0%-20.0%-30.0%-40.0%3691215TapA b s o l u t e % E r r o r182124273020.0%15.0%10.0%5.0%0.0%-5.0%-10.0%-15.0%-20.0%3691215R e l a t i v e % E r r o r1821242730TapBasic Configurations of Electronic PotentiometersBasic CircuitsV R V W /R WV RIThree terminal potentiometer;variable voltage dividerTwo terminal variable resistor;variable currentV HV LCascading Techniques Buffered Reference Voltage –++5VR 1+V-5V V WV REFV OUTOP-07R W /V WR W /V W+V+V+VX(a)(b)V OUT = V W /R WNoninverting Amplifier+–V SV OR 2R 1V O = (1 + R 2/R 1)V SLM308AVoltage Regulator R 1R 2I adjV O (REG) = 1.25V (1 + R 2/R 1) + I adj R 2V O (REG)V IN317Comparator with HysteresisV UL = {R 1/(R 1 + R 2)} V O (max)V LL = {R 1/(R 1 + R 2)} V O (min)+–V SV OR 2R 1}}LT311A+5V-5V(for additional circuits see AN115)0.118 ± 0.002(3.00 ± 0.05)0.040 ± 0.002(1.02 ± 0.05)0.150 (3.81)Ref.0.193 (4.90)0.030 (0.76)0.036 (0.91)0.032 (0.81)0.007 (0.18)0.005 (0.13)0.008 (0.20)0.004 (0.10)0.0216 (0.55)7° Typ.R 0.014 (0.36)0.118 ± 0.002(3.00 ± 0.05)0.012 + 0.006 / -0.002(0.30 + 0.15 / -0.05)0.0256 (0.65) Typ.8-Lead Miniature Small Outline Gull Wing Package Type MNOTE:1.ALL DIMENSIONS IN INCHES AND (MILLIMETERS)Ref.NOTE:1.ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)2.PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH0.020 (0.51)0.016 (0.41)0.150 (3.81)0.125 (3.18)0.110 (2.79)0.090 (2.29)0.430 (10.92)0.360 (9.14)0.300(7.62) Ref.Pin 1 Index0.145 (3.68)0.128 (3.25)0.025 (0.64)0.015 (0.38)Pin 1Seating 0.065 (1.65)0.045 (1.14)0.260 (6.60)0.240 (6.10)0.060 (1.52)0.020 (0.51)Typ. 0.010 (0.25)0°15°8-Lead Plastic Dual In-Line Package Type PHalf Shoulder Width On All End Pins Optional.073 (1.84)Max.0.325 (8.25)0.300 (7.62)PlaneAll Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.Intersil Corporation’s quality certifications can be viewed at /design/qualityIntersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.For information regarding Intersil Corporation and its products, see 0.150 (3.80)0.158 (4.00)0.228 (5.80)0.244 (6.20)0.014 (0.35)0.019 (0.49)Pin 1Pin 1 Index0.010 (0.25)0.020 (0.50)0.050 (1.27)0.188 (4.78)0.197 (5.00)0.004 (0.19)0.010 (0.25)0.053 (1.35)0.069 (1.75)(4X) 7°0.016 (0.410)0.037 (0.937)0.0075 (0.19)0.010 (0.25)0° - 8°X 45°8-Lead Plastic Small Outline Gull Wing Package Type SNOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)。

1780549中文资料

元器件交易网
FFKDSA1/V1-7,62- 3 Order No.: 1780549
http://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1780549
UL Nominal voltage UN Nominal current IN AWG/kcmil Certification 300 V 10 A 22-16 CCA,GmbH & Co. KG http://www.phoenixcontact.de
Page 3 / 3 Mar 1, 2008
End terminal block, 3-pos., 7.62 mm wide, necessary at the end of a row of terminal blocks
Product notes Commercial data EAN Pack Customs tariff Weight/Piece 4017918260057 50 Pcs. 85369010 0.004234 KG http:// Please note that the data given here has been taken from the online catalog. For comprehensive information and data, please refer to the user documentation. The General Terms and Conditions of Use apply to Internet downloads. Certificates / Approvals WEEE/RoHS-compliant since: 01/01/2003

E5557卡中文数据表

模式寄存器 Mode Register
模式寄存器将配置数据保存在EEPROM的第0块，它在上电复位事件或复位命令后每个块的读和（重）装载的开始时不断更新。交货时模式寄存器的值是’00148000’h，它表示连续读第0块，曼彻斯特编码，RF/64 的波特率。图3. 第0块的配置字图 - e5550 兼容模式
Direct Data Output直接数据输出
‘0’=f1=rf/8;‘1’=f2=rf/5 ‘0’=f1=rf/8;‘1’=f2=rf/10 ‘0’=f1=rf/5;‘1’=f2=rf/8 ‘0’=f1=rf/10;‘1’=f2=rf/8
输入变化时相位变化
PSK2(2)
输入为高时在位时钟处相位变化
如果POR延时位被复位，在配置完成后没有附加的延时，在进入射频场后3ms，标签将按正常读模式进入信号调制。如果POR延时位被置位，T5557将再持续8190个内部频率周期的睡眠状态。
在初始化期间，任何的场间隔的出现都将使整个序列重新开始。在初始化延时时间完成以后，T5557 将按配置字中定义的方式进入正常的连续读模式并进行调制。
PSK3(2)
输入的上升沿处相位变化
Manchester ‘0’=下降沿,‘1’=上升沿
Biphase
‘1’产生一个附加的半位变化
NRZ
‘1’=衰减开, ‘0’= 衰减关
注: 1. 推荐一种共用多倍的波特率和FSK频率。
2. 在PSK模式下，选定的数据率是PSK子载波频率的整数倍。
存储器 Memory
存储器是一个330位的EEPROM，它被分成10块，每块33位。每块中的33位包括锁定位，在写操作时同时写入。
第0页第0块包含模式配置写，它在正常的读操作中不传输。第0页第7块可以用来写保护口令。每块的第0位锁定位பைடு நூலகம்一旦被锁定，此块（包括锁定位）将不能通过RF块进行重新写操作。第1页的第1、2块包含了一些描述性数据，当接收到操作码’11’后，此数据将被以配置寄存器定义的调制参数方式发送出来（见图11）。图 4.存储器图

1853764资料

Half screw connection Pg16, made of plastic, consisting of rubber seal with one hole and one pressure screw, for type 1 housings, cable [mm] 9 - 13
Commercial data EAN Pack Customs tariff Weight/Piece Catalog page information Technical data General characteristics Note Degree of protection Type of the screw connection Seal material Ambient temperature (operation) 4017918146306 5 Pcs. 39269097 0.00761 KG Page 304 (PC-2007)
PHOENIX CONTACT GmbH & Co. KG http://www.phoenixcontact.de
Page 1 / 3 Apr 12, 2008
元器件交易网
VC-K-KV-PG16( 9-13) Order No.: 1853764
http://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1853764
元器件交易网
Extract from the online catalog
VC-K-KV-PG16( 9-13)
Order No.: 1853764
The illustration shows a version of the product

1729173资料

Extract from the onlinecatalogMKDSN 1,5/ 7-5,08Order No.: 1729173The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1729173Printed circuit terminal block, nominal current: 13.5 A, rated voltage: 250 V, pitch: 5.08 mm, no. of positions: 7, mounting: Soldering, type of connection: Screw connection, connection direction from the conductor to the PCB: 0°http://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch 5.08 mmDimension a30.48 mmNumber of positions7Pin dimensions0,5 x 1 mm Hole diameter 1.3 mm Screw thread M 3 Tightening torque, min0.5 NmTechnical dataInsulating material group IRated surge voltage (III/3) 4 kV Rated surge voltage (III/2) 4 kV Rated surge voltage (II/2) 4 kV Rated voltage (III/2)400 V Rated voltage (II/2)630 V Connection in acc. with standard EN-VDE Nominal current I N13.5 A Nominal voltage U N250 V Nominal cross section 1.5 mm2 Maximum load current13.5 A Insulating material PA Inflammability class acc. to UL 94V0 Internal cylindrical gage A1 Stripping length 6 mmConnection dataConductor cross section solid min.0.14 mm2 Conductor cross section solid max. 1.5 mm2 Conductor cross section stranded min.0.14 mm2 Conductor cross section stranded max. 1.5 mm2 Conductor cross section stranded, with ferrule0.25 mm2 without plastic sleeve min.Conductor cross section stranded, with ferrule1.5 mm2 without plastic sleeve max.Conductor cross section stranded, with ferrule0.25 mm2 with plastic sleeve min.Conductor cross section stranded, with ferrule1.5 mm2 with plastic sleeve max.Conductor cross section AWG/kcmil min.26 Conductor cross section AWG/kcmil max162 conductors with same cross section, solid min.0.14 mm22 conductors with same cross section, solid max.0.75 mm22 conductors with same cross section, stranded0.14 mm2min.2 conductors with same cross section, stranded0.75 mm2max.2 conductors with same cross section, stranded,0.25 mm2ferrules without plastic sleeve, min.2 conductors with same cross section, stranded,0.5 mm2ferrules without plastic sleeve, max.2 conductors with same cross section, stranded,0.5 mm2TWIN ferrules with plastic sleeve, min.2 conductors with same cross section, stranded,1 mm2TWIN ferrules with plastic sleeve, max.Certificates / ApprovalsCSANominal voltage U N300 VNominal current I N10 AAWG/kcmil28-14CULNominal voltage U N300 VNominal current I N10 AAWG/kcmil30-14ULNominal voltage U N300 VNominal current I N10 AAWG/kcmil30-14Certification CB, CCA, CSA, CUL, GL, GOST, SEV, ULAccessoriesItem Designation DescriptionMarking1051993B-STIFT Marker pen, for manual labeling of unprinted Zack strips, smear-proof and waterproof, line thickness 0.5 mm0804293SK 5,08/3,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 12 identicaldecades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for120 terminal blocks0805085SK 5,08/3,8:SO Marker card, special printing, self-adhesive, labeled acc. tocustomer requirements, 12 identical marker strips per card, max.25-position labeling per strip, color: white0805412SK 5,08/3,8:UNBEDRUCKT Marker cards, unprinted, with pitch divisions, self-adhesive, 10-section marker strips, 12 strips per card, can be labeled with theM-PENTools1205053SZS 0,6X3,5Screwdriver, bladed, matches all screw terminal blocks up to 4.0mm² connection cross section, blade: 0.6 x 3.5 mm, without VDEapprovalDrawingsDrilling diagramDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。

SN65HVD1785DR中文资料

SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793 SLLS872H–JANUARY2008–REVISED FEBRUARY2010 Fault-Protected RS-485Transceivers With Extended Common-Mode RangeCheck for Samples:SN65HVD1785,SN65HVD1786,SN65HVD1787,SN65HVD1791,SN65HVD1792,SN65HVD1793 FEATURES•Bus-Pin Fault Protection to:•Failsafe Receiver for Open-Circuit,Short-Circuit and Idle-Bus Conditions –>±70V('HVD1785,86,91,92)•Low Power Consumption–>±30V('HVD1787,93)–Low Standby Supply Current,1m A Typ •Common-Mode Voltage Range(–20V to25V)More Than Doubles TIA/EIA485Requirement–I CC5mA Quiescent During Operation •Bus I/O Protection•Power-Up,Power-Down Glitch-Free Operation –±16kV JEDEC HBM ProtectionAPPLICATIONS•Reduced Unit Load for Up to256Nodes•Designed for RS-485and RS-422Networks DESCRIPTIONThese devices are designed to survive overvoltage faults such as direct shorts to power supplies,mis-wiring faults,connector failures,cable crushes,and tool mis-applications.They are also robust to ESD events,with high levels of protection to human-body model specifications.These devices combine a differential driver and a differential receiver,which operate from a single power supply.In the'HVD1785,'HVD1786,and'HVD1787,the driver differential outputs and the receiver differential inputs are connected internally to form a bus port suitable for half-duplex(two-wire bus)communication.In the'HVD1793, the driver differential outputs and the receiver differential inputs are separate pins,to form a bus port suitable for full-duplex(four-wire bus)communication.These ports feature a wide common-mode voltage range,making the devices suitable for multipoint applications over long cable runs.These devices are characterized from–40°C to 105°C.For similar features with3.3V supply operation,see the SN65HVD1781(SLLS877).PRODUCT SELECTION GUIDEPART NUMBER DUPLEX SIGNALING RATE NODES CABLE LENGTH SN65HVD1785Half115kbps Up to2561500mSN65HVD1786Half1Mbps Up to256150mSN65HVD1787Half10Mbps Up to6450mSN65HVD1791Full115kbps Up to2561500mSN65HVD1792Full1Mbps Up to256150mSN65HVD1793Full10Mbps Up to6450mPlease be aware that an important notice concerning availability,standard warranty,and use in critical applications of TexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet.PRODUCTION DATA information is current as of publication date.Copyright©2008–2010,Texas Instruments Incorporated Products conform to specifications per the terms of the Texas元器件交易网R RE DE D V CC BA GNDSN65HVD1785, 1786, 1787D or P Package(Top View)1 2 3 48765P0066-021234567141312111098NCGNDGNDZYNCRREDEDVCCVCCABSN65HVD1791, 1792, 1793D Package(Top View)Logic Diagram (Positive Logic)S0299-01ABRREDEDBus Logic Diagram (Positive Logic)AZYBRREDEDS0300-01 SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793SLLS872H–JANUARY2008–REVISED These devices have limited built-in ESD protection.The leads should be shorted together or the device placed in conductive foamduring storage or handling to prevent electrostatic damage to the MOS gates.DEVICE INFORMATIONDRIVER FUNCTION TABLEInput Enable OutputsD DE A BH H H L Actively drive bus highL H L H Actively drive bus lowX L Z Z Driver disabledX OPEN Z Z Driver disabled by defaultOPEN H H L Actively drive bus high by defaultRECEIVER FUNCTION TABLEDifferential Input Enable OutputV ID=V A–V B RE RV IT+<V ID L H Receive valid bus highV IT–<V ID<V IT+L?Indeterminate bus stateV ID<V IT–L L Receive valid bus lowX H Z Receiver disabledX OPEN Z Receiver disabled by defaultOpen-circuit bus L H Fail-safe high outputShort-circuit bus L H Fail-safe high outputIdle(terminated)bus L H Fail-safe high outputNC-No internal connectionPins6and7are connected togetherinternally.Pins13and14are connected togetherinternally.2Submit Documentation Feedback Copyright©2008–2010,Texas Instruments Incorporated 元器件交易网元器件交易网SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793 SLLS872H–JANUARY2008–REVISED FEBRUARY2010ABSOLUTE MAXIMUM RATINGS(1)VALUE UNITV CC Supply voltage–0.5to7V'HVD1785,86,91,92,93A,B pins–70to70V Voltage range at bus pins'HVD1787A,B pins–70to30V'HVD1793Y,Z pins–70to30V Input voltage range at any logic pin–0.3to V CC+0.3VTransient overvoltage pulse through100Ωper TIA-485–100to100VReceiver output current–24to24mAT J Junction temperature170°CSee Dissipation Continuous total power dissipationRating Table IEC60749-26ESD(human-body model),bus terminals and GND±16kVJEDEC Standard22,Test Method A114(human-body model),bus terminals and GND±16kVJEDEC Standard22,Test Method A114(human-body model),all pins±4kVJEDEC Standard22,Test Method C101(charged-device model),all pins±2kVJEDEC Standard22,Test Method A115(machine model),all pins±400V (1)Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device.These are stress ratingsonly and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied.Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.PACKAGE DISSIPATION RATINGSJEDEC THERMAL T A<25°C DERATING FACTOR T A=85°C T A=105°C PACKAGE MODELRATING ABOVE T A=25°C RATING RATINGHigh-K905mW7.25mW/°C470mW325mW SOIC(D)8-pinLow-K516mW 4.1mW/°C268mW186mWHigh-K1315mW10.5mW/°C684mW474mW SOIC(D)14-pinLow-K744mW6mW/°C387mW268mWHigh-K2119mW16.9mW/°C1100mW763mW PDIP(P)8-pinLow-K976mW7.8mW/°C508mW352mW RECOMMENDED OPERATING CONDITIONSMIN NOM MAX UNITV CC Supply voltage 4.55 5.5VV I Input voltage at any bus terminal(separately or common mode)(1)–2025VV IH High-level input voltage(driver,driver enable,and receiver enable inputs)2V CC VV IL Low-level input voltage(driver,driver enable,and receiver enable inputs)00.8VV ID Differential input voltage–2525VOutput current,driver–6060mAI OOutput current,receiver–88mAR L Differential load resistance5460ΩC L Differential load capacitance50pFHVD1785,HVD1791115kbps1/t UI Signaling rate HVD1786,HVD17921MbpsHVD1787,HVD179310Operating free-air temperature(see–40105T A°C application section for thermal information)T J Junction temperature–40150°C(1)By convention,the least positive(most negative)limit is designated as minimum in this data sheet.Copyright©2008–2010,Texas Instruments Incorporated Submit Documentation Feedback3SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793SLLS872H –JANUARY 2008–REVISED FEBRUARY 2010ELECTRICAL CHARACTERISTICSover recommended operating conditions (unless otherwise noted)PARAMETERTEST CONDITIONSMIN TYPMAXUNITRS-485withT A ≤85°C 1.5common-mode load,V CC >4.75V,see T A ≤105°C1.4|V OD |Driver differential output voltage magnitudeVFigure 1R L =54Ω,4.75V ≤V CC ≤5.25V 1.52R L =100Ω,4.75V ≤V CC ≤5.25V2 2.5Change in magnitude of driver differential outputΔ|V OD |R L =54Ω–0.200.2V voltageV OC(SS)Steady-state common-mode output voltage 1V CC /23V Change in differential driver output ΔV OC –1000100mV common-mode voltagePeak-to-peak driver common-mode output Center of two 27-Ωload resistors,See V OC(PP)500mV voltageFigure 2C OD Differential output capacitance23pF Positive-going receiver differential input voltage V IT+–100–10mV thresholdNegative-going receiver differential input V IT–V CM =–20V to 25V–200–150mV voltage thresholdReceiver differential input voltage threshold V HYS 3050mV hysteresis (V IT+–V IT–)V CC I OH =–8mA 2.4–0.3V OHReceiver high-level output voltageVI OH =–400m A4T A ≤85°C 0.20.4V OL Receiver low-level output voltageI OL =8mAV T A ≤105°C0.20.5Driver input,driver enable,and receiver enable I I –100100m A input currentI OZ Receiver output high-impedance current V O =0V or V CC ,RE at V CC –11m A I OSDriver short-circuit output current–250250mAV I =12V 7512585,86,91,92V I =–7V –100–40V CC =4.5to 5.5V or I IBus input current (disabled driver)m A V CC =0V,DE at 0VV I =12V 50087,93V I =–7V–400DE =V CC ,Driver and receiver RE =GND,46enabledno load DE =V CC ,Driver enabled,RE =V CC ,35mAreceiver disabledno load I CCSupply current (quiescent)DE =GND,Driver disabled,RE =GND,24receiver enabled no load DE =GND,Driver and receiver D =open 0.55m AdisabledRE =V CC ,no loadSupply current (dynamic)See TYPICAL CHARACTERISTICS section4Submit Documentation Feedback Copyright ©2008–2010,Texas Instruments Incorporated元器件交易网元器件交易网SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793 SLLS872H–JANUARY2008–REVISED FEBRUARY2010 SWITCHING CHARACTERISTICSover recommended operating conditions(unless otherwise noted)PARAMETER TEST CONDITIONS MIN TYP MAX UNITDRIVER(HVD1785AND HVD1791)t r,t f Driver differential output rise/fall time0.4 1.7 2.6m st PHL,t PLH Driver propagation delay0.82m sR L=54Ω,C L=50pF,See Figure3Driver differential output pulse skew,t SK(P)20250ns |t PHL–t PLH|t PHZ,t PLZ Driver disable time0.15m sSee Figure4andReceiver enabled0.23Figure5t PZH,t PZL Driver enable time m sReceiver disabled312DRIVER(HVD1786AND HVD1792)t r,t f Driver differential output rise/fall time50300nst PHL,t PLH Driver propagation delay200nsR L=54Ω,C L=50pF,See Figure3Driver differential output pulse skew,t SK(P)25ns |t PHL–t PLH|t PHZ,t PLZ Driver disable time3m sSee Figure4andReceiver enabled300nsFigure5t PZH,t PZL Driver enable time Receiver disabled10m sReceiver enabled V CM>V CC500nsDRIVER(HVD1787AND HVD1793)t r,t f Driver differential output rise/fall time330nst PHL,t PLH Driver propagation delay50nsR L=54Ω,C L=50pF,See Figure3Driver differential output pulse skew,t SK(P)10ns |t PHL–t PLH|t PHZ,t PLZ Driver disable time3m sSee Figure4andReceiver enabled300nsFigure5t PZH,t PZL Driver enable time Receiver disabled9m sReceiver enabled V CM>V CC500nsRECEIVER(ALL DEVICES UNLESS OTHERWISE NOTED)t r,t f Receiver output rise/fall time415ns85,86,91,92100200t PHL,t PLH Receiver propagation delay time nsC L=15pF,87,9370See Figure685,86,91,92620 Receiver output pulse skew,t SK(P)ns |t PHL–t PLH|87,935t PLZ,t PHZ Receiver disable time Driver enabled,See Figure715100nst PZL(1),t PZH(1)Driver enabled,See Figure780300nsReceiver enable timet PZL(2),t PZH(2)Driver disabled,See Figure839m s Copyright©2008–2010,Texas Instruments Incorporated Submit Documentation Feedback50 V or 3 V–20 V < V(test) < 25 VS0301-01InputA BV A V B V OC(PP)D V V OCV CCL Instrumentation CapacitanceS0302-01SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793SLLS872H –JANUARY 2008–REVISED FEBRUARY 2010THERMAL INFORMATIONPARAMETERTEST CONDITIONSVALUE UNITJEDEC high-K model 138SOIC-8JEDEC low-K model 242JEDEC high-K model 59R q JA Junction-to-ambient thermal resistance (no airflow)DIP-8°C/W JEDEC low-K model 128JEDEC high-K model 95SOIC-14JEDEC low-K model168SOIC-862R q JB Junction-to-board thermal resistanceDIP-839°C/W SOIC-1440SOIC-861R q JC Junction-to-case thermal resistanceDIP-861°C/W SOIC-1444V CC =5.5V,T J =150°C,R L =300Ω,85,91C L =50pF (driver),C L =15pF (receiver)2905-V supply,unterminated (1)85,91V CC =5.5V,T J =150°C,R L =100Ω,C L =50pF (driver),C L =15pF (receiver)863205-V supply,RS-422load (1)P DPower dissipationmW8785,91V CC =5.5V,T J =150°C,R L =54Ω,400C L =50pF (driver),C L =15pF (receiver)865-V supply,RS-485load (1)87T SDThermal-shutdown junction temperature170°C(1)Driver and receiver enabled,50%duty cycle square-wave signal at signaling rate:HVD1785,1791at 115kbps,HVD1786at 1Mbps,HVD1787at 10Mbps)PARAMETER MEASUREMENT INFORMATIONInput generator rate is 100kbps,50%duty cycle,rise and fall times less than 6nsec,output impedance 50Ω.Figure 1.Measurement of Driver Differential Output Voltage With Common-Mode LoadFigure 2.Measurement of Driver Differential and Common-Mode Output With RS-485Load6Submit Documentation Feedback Copyright ©2008–2010,Texas Instruments Incorporated元器件交易网3 V»2 V»–2 VV IV ODC = 50 pF 20%L ±C Includes Fixture L and Instrumentation CapacitanceS0303-013 V0 V V OH »0 VV IV O R = 110L W ±1%S0304-01V O3 V»3 V0 V V OLV IV O= 110W »3 VS0305-01SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793SLLS872H –JANUARY 2008–REVISED FEBRUARY 2010PARAMETER MEASUREMENT INFORMATION (continued)Figure 3.Measurement of Driver Differential Output Rise and Fall Times and Propagation DelaysNOTE:D at 3V to test non-inverting output,D at 0V to test inverting output.Figure 4.Measurement of Driver Enable and Disable Times With Active High Output and Pulldown LoadNOTE:D at 0V to test non-inverting output,D at 3V to test inverting output.Figure 5.Measurement of Driver Enable and Disable Times With Active-Low Output and Pullup LoadCopyright ©2008–2010,Texas Instruments Incorporated Submit Documentation Feedback 7元器件交易网3 VV OH V OLV IV OC = 15 pF 20%L ±C Includes Fixture and Instrumentation CapacitanceL 0 V S0306-013 V 0 V or 3 V 3 V0 VV OH0 VV OV IS1D at 3 V S1 to GNDCCV OLV OD at 0 V S1 to V CCS0307-01SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793SLLS872H –JANUARY 2008–REVISED FEBRUARY 2010PARAMETER MEASUREMENT INFORMATION (continued)Figure 6.Measurement of Receiver Output Rise and Fall Times and Propagation DelaysFigure 7.Measurement of Receiver Enable/Disable Times With Driver Enabled8Submit Documentation Feedback Copyright ©2008–2010,Texas Instruments Incorporated元器件交易网V CC3 V0 VV OHGNDV IV OV OA at 1.5 VB at 0 V S1 to GNDV CCV OLA at 0 VB at 1.5 V S1 to V CCS1S0308-01SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793SLLS872H –JANUARY 2008–REVISED FEBRUARY 2010PARAMETER MEASUREMENT INFORMATION (continued)Figure 8.Measurement of Receiver Enable Times With Driver DisabledCopyright ©2008–2010,Texas Instruments Incorporated Submit Documentation Feedback 9元器件交易网V CC − Supply Voltage − V−100102030405060700.00.6 1.21.82.43.03.64.24.85.4I O − D r i v e r O u t p u t C u r r e n t − m AG001Signaling Rate − Mbps 406080100120246810I C C − R M S S u p p l y C u r r e n t − m AG002V IN − Bus Pin Voltage − V−2.0−1.5−1.0−0.50.00.51.01.52.0−90−60−300306090I I N − B u s P i n C u r r e n t − m AG004SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793SLLS872H –JANUARY 2008–REVISED FEBRUARY 2010TYPICAL CHARACTERISTICSDRIVER OUTPUT CURRENTHVD1787RMS SUPPLY CURRENTvsvsSUPPLY VOLTAGESIGNALING RATEFigure 9.Figure 10.BUS PIN CURRENTvsFigure 11.10Submit Documentation Feedback Copyright ©2008–2010,Texas Instruments Incorporated元器件交易网02468101214161820222426283032343638404244464850Idiff -Differential Load Current - mAV O D - D i f f e r e n t i a l O u t p u t V o l t a g e - VSN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793SLLS872H –JANUARY 2008–REVISED FEBRUARY 2010TYPICAL CHARACTERISTICS (continued)DIFFERENTIAL OUTPUT VOLTAGEvsDIFFERENTIAL LOAD CURRENTFigure 12.Copyright ©2008–2010,Texas Instruments Incorporated Submit Documentation Feedback 11元器件交易网R RE DE DV CCBAGNDD Package(Top View)12348765P0066-03S0309-01ABRREDEDV D Package(Top View)P0074-01AZYBRDS0310-01SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793SLLS872H–JANUARY2008–REVISED ADDITIONAL OPTIONSThe SN65HVD17xx family also has options for J1708applications,for always-enabled full-duplex versions (industry-standard SN65LBC179footprint)and for inverting-polarity versions,which allow users to correct a reversal of the bus wires without re-wiring.Contact your local Texas Instruments representative for information on these options.PART NUMBER SN65HVD17xxFOOTPRINT/FUNCTION SLOW MEDIUM FASTHalf-duplex(176pinout)858687Full-duplex no enables(179pinout)888990Full-duplex with enables(180pinout)919293Half-duplex with cable invert949596Full-duplex with cable invert and enables979899J1708080910Figure13.SN65HVD1708E Transceiver for J1708ApplicationsFigure14.SN65HVD17xx Always-Enabled Driver Receiver12Submit Documentation Feedback Copyright©2008–2010,Texas Instruments Incorporated 元器件交易网R INV DE DV CCBAGND D Package(Top View)123487651234567141312111098RINVGND GND ZY DINVR RE DE DV CCV CCABD Package(Top View)P0066-04ABRDEDINVS0311-01YZBARDEDDINVRERINVSN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793 SLLS872H–JANUARY2008–REVISED FEBRUARY2010Figure15.SN65HVD17xx Options With Inverting Feature to Correct for Miswired CablesAPPLICATION INFORMATIONHot-PluggingThese devices are designed to operate in"hot swap"or"hot pluggable"applications.Key features for hot-pluggable applications are power-up,power-down glitch free operation,default disabled input/output pins, and receiver failsafe.As shown in Figure9,an internal Power-On Reset circuit keeps the driver outputs in a high-impedance state until the supply voltage has reached a level at which the device will reliably operate.This ensures that no spurious transitions(glitches)will occur on the bus pin outputs as the power supply turns on or turns off.As shown in the device FUNCTION TABLE,the ENABLE inputs have the feature of default disable on both the driver enable and receiver enable.This ensures that the device will neither drive the bus nor report data on the R pin until the associated controller actively drives the enable pins.Copyright©2008–2010,Texas Instruments Incorporated Submit Documentation Feedback13元器件交易网元器件交易网SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793SLLS872H–JANUARY2008–REVISED Receiver FailsafeThe differential receiver is“failsafe”to invalid bus states caused by:•open bus conditions such as a disconnected connector,•shorted bus conditions such as cable damage shorting the twisted-pair together,•or idle bus conditions that occur when no driver on the bus is actively driving.In any of these cases,the differential receiver outputs a failsafe logic High state,so that the output of the receiver is not indeterminate.In the HVD17xx family of RS-485devices,receiver failsafe is accomplished by offsetting the receiver thresholds so that the“input indeterminate”range does not include zero volts differential.In order to comply with the RS-422 and RS-485standards,the receiver output must output a High when the differential input V ID is more positive than200mV,and must output a Low when the V ID is more negative than-200mV.The HVD17xx receiver parameters which determine the failsafe performance are V IT+and V IT-and V HYS.In the Electrical Characteristics table,V IT-has a typical value of-150mV and a minimum(most negative)value of-200mV,so differential signals more negative than-200mV will always cause a Low receiver output.Similarly,differential signals more positive than200mV will always cause a High receiver output,because the typical value of V IT+is-100mV,and V IT+is never more positive than-10mV under any conditions of temperature,supply voltage,or common-mode offset. When the differential input signal is close to zero,it will still be above the V IT+threshold,and the receiver output will be High.Only when the differential input is more negative than V IT-will the receiver output transition to a Low state.So,the noise immunity of the receiver inputs during a bus fault condition includes the receiver hysteresis value V HYS(the separation between V IT+and V IT-)as well as the value of V IT+.For the HVD17xx devices,the typical noise immunity is typically about150mV,which is the negative noise level needed to exceed the V IT-threshold(V IT-TYP=-150mV).In the worst case,the failsafe noise immunity is never less than40mV,which is set by the maximum positive threshold(V IT+MAX=-10mV)plus the minimum hysteresis voltage(V HYS MIN=30mV).70-V Fault-ProtectionThe SN65HVD17xx family of RS-485devices is designed to survive bus pin faults up to±70V.The devices designed for fast signaling rate(10Mbps)will not survive a bus pin fault with a direct short to voltages above 30V when:1.the device is powered on AND2a.the driver is enabled(DE=HIGH)AND D=HIGH AND the bus fault is applied to the A pin OR2b.the driver is enabled(DE=HIGH)AND D=LOW AND the bus fault is applied to the B pinUnder other conditions,the device will survive shorts to bus pin faults up to70V.Table1summarizes the conditions under which the device may be damaged,and the conditions under which the device will not be damaged.Table1.Device ConditionsPOWER DE D A B RESULTSOFF X X-70V<V A<70V-70V<V B<70V Device survivesON LO X-70V<V A<70V-70V<V B<70V Device survivesON HI L-70V<V A<70V-70V<V B<30V Device survivesON HI L-70V<V A<70V30V<V B Damage may occurON HI H-70V<V A<30V-70V<V B<30V Device survivesON HI H30V<V A-70V<V B<30V Damage may occur14Submit Documentation Feedback Copyright©2008–2010,Texas Instruments Incorporated元器件交易网SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793 SLLS872H–JANUARY2008–REVISED FEBRUARY2010REVISION HISTORYChanges from Original(January2008)to Revision A Page •Changed Features Bullet From:Low Standby Supply Current,2m A Max To:Low Standby Supply Current,1m A Typ (1)•Deleted columns to the PRODUCT SELECTION GUIDE for Package Options and Status (1)•Added text:For similar features with3.3V supply operation (1)•Changed the Product Selection Guide Signaling Rate for SN65HVD1787From20Mbps To:10Mbps (1)•Changed the Product Selection Guide Signaling Rate for SN65HVD1793From20Mbps To:10Mbps (1)•Deleted The Competitive Comparison table (2)•Added|V OD|RS-485with common-mode load T A≤85°C and T A≤105°C (4)•ChangedΔV OC From min=-0.2mV and max0.2mV To:min=-100mV and max100mV (4)•Changed HVD1785/1791Driver differential output rise/fall time max value From2.5m s To:2.6m s (5)•Changed HVD1787/1793Driver differential output rise/fall time max value From1.5ns To:30ns (5)•Changed Receiver propagation delay max value From50ns To:70ns (5)•Changed t PLZ,t PHZ Receiver disable time From3000ns To100ns (5)•Deleted graph DIFFERENTIAL OUTPUT VOLTAGE vs DIFFERENTIAL LOAD CURRENT (10)Changes from Revision A(March2008)to Revision B Page •Added T A≤85°C and T A≤105°C conditions and values to the Receiver low-level output voltage (4)•Changed the max value for Supply Current(quiescent)Driver and receiver disabled,From1m A To5m A (4)Changes from Revision B(March2008)to Revision C Page •Changed Rec Op Table.Signaling rate,HVD1787,HVD1793From:20Mbps max to10Mbps max (3)Changes from Revision C(March2008)to Revision D Page •Added Features Bullet:Power-Up,Power-Down Glitch-Free Operation (1)•Changed(Preview)to part number SN65HVD1791in the Product Selection Guide (1)•Changed Receiver disabled by default-Enable from X to OPEN.Output from OPEN to Z (2)•Changed SN65HVD1791,1792,1793pin out.Pin11from A to B,Pin12from B to A (2)•Added section-APPLICATION INFORMATION (13)Changes from Revision D(June2008)to Revision E Page •Changed-Removed Product Preview label (1)•Changed SN65HVD1792Removed Product Preview label (1)•Changed SN65HVD1793Removed Product Preview label (1)Changes from Revision E(July2008)to Revision F Page •Added to Title:With Extended Common-Mode Range (1)•Added Receiver enabled V CM>V CC condition and values to the Driver enabled time (5)•Added Figure12 (11)Copyright©2008–2010,Texas Instruments Incorporated Submit Documentation Feedback15元器件交易网SN65HVD1785,SN65HVD1786SN65HVD1787,SN65HVD1791SN65HVD1792,SN65HVD1793SLLS872H–JANUARY2008–REVISED Changes from Revision F(November2008)to Revision G Page •Added Notes for pin connections (2)•Added I OH=–400m A conditions and values to the Receiver high-level output voltage (4)•Added Receiver enabled V CM>V CC (5)•Added Receiver Failsafe information (13)•Changed the Receiver Failsafe section (14)Changes from Revision G(April2009)to Revision H Page •Deleted70-V from the data sheet title (1)•Changed first Features Bullet From:Bus-Pin Fault Protection to>±70V To:Bus-Pin Fault Protection to:>±70V ('HVD1785,86,91,92),>±30V('HVD1787,93) (1)•Changed Voltage range at A and B inputs in the ABS MAX RATINGS table,adding seperate conditions for the different devices (3)•Changed From:Voltage input range,transient pulse,A and B,through100ΩTo:Transient overvoltage pulse through100Ωper TIA-485 (3)•Changed Figure14From:PW Package(Top View)To:D Package(Top View) (12)•Added the70-V Fault-Protection section (14)16Submit Documentation Feedback Copyright©2008–2010,Texas Instruments IncorporatedPACKAGING INFORMATIONOrderable Device Status(1)PackageType PackageDrawingPins PackageQtyEco Plan(2)Lead/Ball Finish MSL Peak Temp(3)SN65HVD1785D ACTIVE SOIC D875Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1785DG4ACTIVE SOIC D875Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1785DR ACTIVE SOIC D82500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1785DRG4ACTIVE SOIC D82500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1785P ACTIVE PDIP P850Green(RoHS&no Sb/Br)CU NIPDAU N/A for Pkg TypeSN65HVD1786D ACTIVE SOIC D875Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1786DG4ACTIVE SOIC D875Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1786DR ACTIVE SOIC D82500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1786DRG4ACTIVE SOIC D82500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1786P ACTIVE PDIP P850Green(RoHS&no Sb/Br)CU NIPDAU N/A for Pkg TypeSN65HVD1787D ACTIVE SOIC D875Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1787DG4ACTIVE SOIC D875Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1787DR ACTIVE SOIC D82500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1787DRG4ACTIVE SOIC D82500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1787P ACTIVE PDIP P850Green(RoHS&no Sb/Br)CU NIPDAU N/A for Pkg TypeSN65HVD1791D ACTIVE SOIC D1450Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1791DG4ACTIVE SOIC D1450Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1791DR ACTIVE SOIC D142500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1791DRG4ACTIVE SOIC D142500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1792D ACTIVE SOIC D1450Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1792DR ACTIVE SOIC D142500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1793D ACTIVE SOIC D1450Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN65HVD1793DR ACTIVE SOIC D142500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIM(1)The marketing status values are defined as follows:ACTIVE:Product device recommended for new designs.LIFEBUY:TI has announced that the device will be discontinued,and a lifetime-buy period is in effect.。

1733570资料

Extract from the onlinecatalogSMKDSP 1,5/ 2-5,08Order No.: 1733570The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1733570Printed circuit terminal block, nominal current: 17.5 A, rated voltage: 250 V, pitch: 5.08 mm, no. of positions: 2, mounting: Soldering, type of connection: Screw connection, connection direction from the conductor to the PCB: 35°http://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch 5.08 mmDimension a10.16 mmNumber of positions2Pin dimensions0,9 x 0,9 mmHole diameter 1.3 mmScrew thread M 3Tightening torque, min0.5 NmTechnical dataInsulating material group IRated surge voltage (III/3) 4 kVRated surge voltage (III/2) 4 kVRated surge voltage (II/2) 4 kVRated voltage (III/2)320 VRated voltage (II/2)630 VConnection in acc. with standard EN-VDENominal current I N17.5 ANominal voltage U N250 VNominal cross section 1.5 mm2Maximum load current22 A (with 2.5 mm2 conductor cross section) Insulating material PAInflammability class acc. to UL 94V0Internal cylindrical gage A1Stripping length7 mmConnection dataConductor cross section solid min.0.14 mm2Conductor cross section solid max. 2.5 mm2Conductor cross section stranded min.0.14 mm2Conductor cross section stranded max. 1.5 mm2Conductor cross section stranded, with ferrule0.25 mm2without plastic sleeve min.Conductor cross section stranded, with ferrule1.5 mm2without plastic sleeve max.Conductor cross section stranded, with ferrule0.25 mm2with plastic sleeve min.Conductor cross section stranded, with ferrule1.5 mm2with plastic sleeve max.Conductor cross section AWG/kcmil min.26Conductor cross section AWG/kcmil max142 conductors with same cross section, solid min.0.14 mm22 conductors with same cross section, solid max. 1 mm22 conductors with same cross section, stranded0.14 mm2min.2 conductors with same cross section, stranded0.75 mm2max.2 conductors with same cross section, stranded,0.25 mm2ferrules without plastic sleeve, min.2 conductors with same cross section, stranded,0.5 mm2ferrules without plastic sleeve, max.2 conductors with same cross section, stranded,0.5 mm2TWIN ferrules with plastic sleeve, min.2 conductors with same cross section, stranded,1 mm2TWIN ferrules with plastic sleeve, max.Certificates / ApprovalsCSANominal voltage U N300 VNominal current I N10 AAWG/kcmil28-14CULNominal voltage U N300 VNominal current I N10 AAWG/kcmil30-14ULNominal voltage U N300 VNominal current I N10 AAWG/kcmil30-14Certification CB, CCA, CSA, CUL, GOST, SEV, ULAccessoriesItem Designation DescriptionMarking0804293SK 5,08/3,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 12 identicaldecades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for120 terminal blocksPlug/Adapter0201744MPS-MT Test plug, consisting of: Metal part for 2.3 mm diameter sockethole0201647RPS Reducing plug, for transition from 4 mm diameter test plug socket,insulation: grayTools1205053SZS 0,6X3,5Screwdriver, bladed, matches all screw terminal blocks up to 4.0mm² connection cross section, blade: 0.6 x 3.5 mm, without VDEapprovalDrawingsDrilling diagramDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。

S1D13305中文资料

元器件交易网
The information of the product number change
Starting April 1, 2001, the product number will be changed as listed below. To order from April 1, 2001 please use the new product number. For further information, please contact Epson sales representative.
SDU1374#0C SDU1375#0C SDU1376#0C SDU1376BVR SDU1378#0C
• S1D1380x Series New No. Previous No.
SDU1386#0C
New No.
S5U13806P00C
S5U13503P00C S5U13504P00C S5U13505P00C S5U13506P00C
S1D13305 Series S1D13305D00A S1D13305F00A S1D13305F00B
S1D1370x Series S1D13704F00A S1D13705F00A S1D13706B00A S1D13706F00A S1D13708 Series
• S1D1350x Series Previous No.
S5U13704P00C S5U13705P00C S5U13706P00C S5U13706B32R S5U13708P00C
• S1D13A0x Series Previous No.
SDU13A3#0C SDU13A4#0C
New No.

1755587资料

Extract from the onlinecatalogMSTBVA 2,5/ 9-GOrder No.: 1755587The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1755587Header, nominal current: 12 A, rated voltage: 250 V, pitch: 5.0 mm, no. of positions: 9, mounting: Solderinghttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch 5 mmDimension a40 mmNumber of positions9Pin dimensions 1 x 1 mmHole diameter 1.4 mmTechnical dataInsulating material group IIIaRated surge voltage (III/3) 4 kVRated surge voltage (III/2) 4 kVRated surge voltage (II/2) 4 kVRated voltage (III/2)320 VRated voltage (II/2)400 VConnection in acc. with standard EN-VDENominal current I N12 ANominal voltage U N250 VMaximum load current12 AInsulating material PBTInflammability class acc. to UL 94V0Certificates / ApprovalsCSANominal voltage U N300 VNominal current I N10 ACULNominal voltage U N300 VNominal current I N10 AULNominal voltage U N300 VNominal current I N10 ACertification CB, CSA, CUL, GOST, UL, VDE-PZIAccessoriesItem Designation DescriptionAssembly1755477MSTB-BL Keying cap, for forming sections, plugs onto header pin, greeninsulating materialMarking0804183SK 5/3,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 12 identicaldecades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for120 terminal blocksPlug/Adapter1734401CR-MSTB Coding section, inserted into the recess in the header or theinverted plug, red insulating materialAdditional productsItem Designation DescriptionAssembly1909281FKCT 2,5/ 9-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 9, type of connection: Spring-cageconnectionGeneral1910429FKC 2,5/ 9-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 9, type of connection: Spring-cageconnection1909786FKCVR 2,5/ 9-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 9, type of connection: Spring-cageconnection1910102FKCVW 2,5/ 9-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 9, type of connection: Spring-cageconnection1779482FRONT-MSTB 2,5/ 9-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 9, type of connection: Screwconnection1754588MSTB 2,5/ 9-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 9, type of connection: Screwconnection1758995MSTB 2,5/ 9-STZ Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 9, type of connection: Screwconnection1765849MSTBP 2,5/ 9-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 9, type of connection: Screwconnection1779903MSTBT 2,5/ 9-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 9, type of connection: Screwconnection1792087MVSTBR 2,5/ 9-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 9, type of connection: Screwconnection1792595MVSTBW 2,5/ 9-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 9, type of connection: Screwconnection1768820SMSTB 2,5/ 9-ST Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.0 mm, no. of positions: 9, type of connection: ScrewconnectionDrawingsDrilling diagramDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。

1758843资料

Extract from the online catalogMSTB 2,5/ 4-ST-5,08 BKOrder No.: 1758843http://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1758843Plug component, nominal current: 12 A, rated voltage: 250 V, pitch:5.08 mm, no. of positions: 4, type of connection: Screw connection,color: Blackhttp:// Please note that the data given here has been taken from theonline catalog. For comprehensive information and data, please refer to the user documentation. The General Terms and Conditions of Use apply to Internet downloads.Certificates / ApprovalsCSANominal voltage U N 300 V Nominal current I N 10 A AWG/kcmil28-12CULNominal voltage U N300 VNominal current I N10 AAWG/kcmil30-12ULNominal voltage U N300 VNominal current I N10 AAWG/kcmil30-12Certification CB, CSA, CUL, UL, VDE-PZIAccessoriesItem Designation DescriptionBridges1733172EBP 3- 5Insertion bridge, fully insulated, for plug connectors with 5.0 or5.08 mm pitch, no. of positions: 31733185EBP 4- 5Insertion bridge, fully insulated, for plug connectors with 5.0 or5.08 mm pitch, no. of positions: 4General1733169EBP 2- 5Insertion bridge, fully insulated, for plug connectors with 5.0 or5.08 mm pitch, no. of positions: 21803882KGG-MSTB 2,5/ 4Cable housing, for cable diameters of 5 -9.5 mm, clamp, screws,and marker strips are included, color: green, no. of positions: 4Marking0804293SK 5,08/3,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 12 identicaldecades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for120 terminal blocksPlug/Adapter1734634CP-MSTB Coding profile, is inserted into the slot on the plug or invertedheader, red insulating materialTools1205053SZS 0,6X3,5Screwdriver, bladed, matches all screw terminal blocks up to 4.0mm² connection cross section, blade: 0.6 x 3.5 mm, without VDEapprovalAdditional productsItem Designation DescriptionGeneral1880326EMSTBA 2,5/ 4-G-5,08Header, nominal current: 12 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 4, mounting: press in1859535EMSTBVA 2,5/ 4-G-5,08Header, nominal current: 12 A, rated voltage: 200 V, pitch: 5.08mm, no. of positions: 4, mounting: Press in1873375FKIC 2,5/ 4-ST-5,08Plug component, nominal current: 12 A, rated voltage: 320 V,pitch: 5.08 mm, no. of positions: 4, type of connection: Spring-cage connection1823862ICC 2,5/ 4-STZ-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 4, type of connection: Crimpconnection1736713MDSTB 2,5/ 4-G1-5,08Header, nominal current: 10 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 4, mounting: Soldering1842089MDSTBA 2,5/ 4-G-5,08Header, nominal current: 10 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 4, mounting: Soldering1736755MDSTBV 2,5/ 4-G1-5,08Header, nominal current: 10 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 4, mounting: Soldering1770737MSTB 2,5/ 4-G-5,08-LA Header, nominal current: 12 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 4, mounting: Soldering1757268MSTBA 2,5/ 4-G-5,08Header, nominal current: 12 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 4, mounting: Soldering1770960MSTBA 2,5/ 4-G-5,08-LA Header, nominal current: 12 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 4, mounting: Soldering1788745MSTBVK 2,5/ 4-G-5,08Header, nominal current: 12 A, rated voltage: 320 V, pitch: 5.08mm, no. of positions: 4, mounting: Mounting rail1788554MVSTBU 2,5/ 4-GB-5,08Header, nominal current: 12 A, rated voltage: 320 V, pitch: 5.08mm, no. of positions: 4, mounting: Direct mounting1769489SMSTB 2,5/ 4-G-5,08Header, nominal current: 12 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 4, mounting: Soldering1767397SMSTBA 2,5/ 4-G-5,08Header, nominal current: 12 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 4, mounting: Soldering3002034UK 3-MSTB-5,08Modular terminal blocks with plug entry, cross section: 0.2 - 2.5mm², AWG: 30 - 12, width: 5.1 mm, color: gray3002076UK 3-MVSTB-5,08Modular terminal blocks with plug entry, cross section: 0.2 - 2.5mm², AWG: 26 - 12, width: 5.1 mm, color: gray3002102UK 3-MVSTB-5,08-LA 24RD Modular terminal block with plug entry, nominal current: 12 A,rated voltage: 320 V, pitch: 5.08 mm, no. of positions: 1, mounting:mounting rail, with red light indicator, voltage light indicator: 24 VAC/DC, current light indicator: 3.3 mA3002063UK 3-MVSTB-5,08/EK Modular terminal blocks with plug entry, cross section: 0.2-2.5mm², AWG: 26-12, width: 5.1 mm, color: blue3002131UK 3D-MSTBV-5,08Modular terminal blocks with vertical plug entry, cross section: 0.2- 2.5 mm, AWG: 30 - 12, width: 5.1 mm, color: gray3002144UK 3D-MSTBV-5,08-LA 24RD Modular terminal block with vertical plug entry, color: Gray, withred light indicator, voltage light indicator: 24 V AC/DC, current lightindicator: 3.3 mA3002173UK 3D-MSTBV-5,08/EK Modular terminal blocks with plug entry, cross section: 0.2 - 2.5mm², AWG: 30 - 12, width: 5.1 mm, color: blue2770888UKK 3-MSTB-5,08Modular terminal blocks with 2 horizontal plug entries, crosssection: 0.2 - 2.5 mm, AWG: 30 - 12, width: 5.1 mm, color: gray 1876615UKK 3-MSTB-5,08-PE Ground terminal block, with 2 horizontal plug entries, nominalcurrent: 12 A, rated voltage: 320 V, pitch: 5.08 mm, no. ofpositions: 1, mounting: mounting rail.2770846UKK 3-MSTBVH-5,08Modular terminal blocks with vertical and horizontal plug entry,cross section: 0.2 - 2.5 mm, AWG: 30 - 12, width: 5.1 mm, color:gray1788130UMSTBVK 2,5/ 4-G-5,08Header, nominal current: 12 A, rated voltage: 320 V, pitch: 5.08mm, no. of positions: 4, mounting: Mounting rail1873016ZFKK 1,5-MSTBV-5,08Modular terminal blocks with plug entry, cross section: 0.2 - 1.5mm², width: 5.1 mm, color: grayAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。