744760215C;中文规格书,Datasheet资料
744230181;中文规格书,Datasheet资料
2.1 2.0 1.02012-07-172012-07-172010-09-30SStSStSBaSStSBaWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]F Typical Impedance Characteristics:H1: Classification Reflow Profile for SMT components:H2: Classification Reflow ProfilesProfile FeaturePreheat- Temperature Min (T smin ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Ramp-up rate (T L to T P )Liquidous temperature (T L )Time (t L ) maintained above T L Peak package body temperature (T p )Time within 5°C of actual peak temperature (t p )Ramp-down rate (T P to T L )Time 25°C to peak temperature Pb-Free Assembly 150°C 200°C60-180 seconds 3°C/ second max.217°C60-150 seconds See Table H320-30 seconds 6°C/ second max.8 minutes max.refer to IPC/JEDEC J-STD-020DH3: Package Classification Reflow TemperaturePB-Free Assembly PB-Free Assembly PB-Free Assembly Package Thickness< 1.6 mm 1.6 - 2.5 mm ≥ 2.5 mmVolume mm³<350260°C 260°C 250°CVolume mm³350 - 2000260°C 250°C 245°CVolume mm³>2000260°C 245°C 245°Crefer to IPC/JEDEC J-STD-020DH Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-CNSWof Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Cleaning solvents which are used to clean the application might damage or change the characteristics of the component.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The soldering profile has to be complied with according to the technical reflow soldering specification, otherwise no warranty will be su-stained.•All products are supposed to be used before the end of the period of 12 months based on the transfer of title, if not a 100% solderability can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744230181。
744770268;中文规格书,Datasheet资料
Bezeichnung :description := Start of winding Marking = Inductance code33% Umgebungstemperatur / temperature:+20°C100% SnMST 04-10-11MST 03-12-10RT 03-03-03MST02-03-27MST 02-02-20NameDatum / dateIt is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions.Anbindung an Elektrode / soldering wire to plating:Sn/Ag/Cu - 96.5/3.0/0.5%Draht / wire:2SFBW 155°CUmgebungstemp. / ambient temperature: -40°C - + 85°C Freigabe erteilt / general release:Kunde / customerWürth Elektronik....................................................................................................................................................................Unterschrift / signature Ferrit/ferrite F Werkstoffe & Zulassungen / material & approvals :G Eigenschaften / general specifications :D Prüfgeräte / test equipment :E Testbedingungen / test conditions :Basismaterial / base material:Betriebstemp. / operating temperature: -40°C - + 125°C D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked ..........................................................................................................................Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KG744770268SPEICHERDROSSEL WE-PDPOWER-CHOKE WE-PDArtikelnummer / part number : Luftfeuchtigkeit / humidity:HP 4274 A für/for L und/and Q HP 34401 A für/for I DC und/and R DCÄnderung / modificationVersion 1Version 2Version 3Version 4Version 5 Datum / dateEndoberfläche / finishing electrode:• MarkingRoHS compliantLFdescription :MST 04-10-11MST 03-12-10RT 03-03-03MST02-03-27MST 02-02-20NameDatum / dateH Induktivitätskurve / Inductance curve :POWER-CHOKE WE-PDDATUM / DATE : 2004-10-11Kontrolliert / approvedDatum / dateUnterschrift / signature Würth ElektronikWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Freigabe erteilt / general release:Kunde / customer..................................................................................................................................................................................................................................................................................Geprüft / checked Version 4Version 5Änderung / modificationVersion 1Version 2Version 3a 330,0± 0,5mmb 20,20± 0,2mm+ 0,5- 1,0d 100,0± 0,2mmMST 04-10-11MST 03-12-10RT 03-03-03MST02-03-27MST 02-02-20NameDatum / dateRollenspezifikation / Reel specification:Freigabe erteilt / general release:Kunde / customerc 13,00mm....................................................................................................................................................................Datum / dateUnterschrift / signature Würth Elektronik..........................................................................................................................Würth Elektronik eiSos GmbH & Co. KGGeprüft / checked Kontrolliert / approvedD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Änderung / modificationVersion 1Version 2Version 3Version 4Version 5The force for tearing off cover tape is 10 to 130 grams in arrow direction165 to 180°feeding directionThis electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such as aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electronic equipments, when used in electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stage.分销商库存信息: WURTH-ELECTRONICS 744770268。
7447789215;中文规格书,Datasheet资料
description := Start of winding Marking = Inductance code33% Umgebungstemperatur / temperature:+20°C100% SnSSt 06-01-10MST 04-10-11SST 04-07-28SST04-04-21SST 04-04-08NameDatum / datenot exceed 125°C under worst case operating conditions.Draht / wire:2SFBW; 155°POWER-CHOKE WE-PD.............................................Umgebungstemp. / ambient temperature: -40°C - + 85°C Basismaterial / base material: Endoberfläche / finishing electrode:D Prüfgeräte / test equipment :E Testbedingungen / test conditions :HP 4274 A für/for L und/and Q F Werkstoffe & Zulassungen / material & approvals :G Eigenschaften / general specifications :Ferrit/ferrite HP 34401 A für/for I DC und/and R DCLuftfeuchtigkeit / humidity:Freigabe erteilt / general release:Kunde / customerAnbindung an Elektrode / soldering wire to plating:Betriebstemp. / operating temperature: -40°C - + 125°C It is recommended that the temperature of the part does Sn/Ag/Cu - 96.5/3.0/0.5%Würth Elektronik................................................................................Datum / date................................................................................Unterschrift / signatureVersion 5Änderung / modificationVersion 1Version 2Version 3Version 4 http://www.we-online.deKontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked ...................................................description :H Induktivitätskurve / Inductance curve :SSt 06-01-10MST 04-10-11SST 04-07-28SST04-04-21SST 04-04-08NameDatum / datePOWER-CHOKE WE-PDDATUM / DATE : 2006-01-10Würth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400http://www.we-online.de................................................................................................Geprüft / checked Kontrolliert / approvedDatum / dateUnterschrift / signature Würth ElektronikFreigabe erteilt / general release:Kunde / customer................................................................................................................................................................Änderung / modificationVersion 1Version 2Version 3Version 4Version 5description :A 10,0± 0,1B 16,0± 0,2+ 0,1a 330,0± 2,0mm b 21,0± 0,8mm c 13,0± 0,5mm d 100,0± 1,0mm SSt 06-01-10MST 04-10-11SST 04-07-28SST04-04-21SST 04-04-08NameDatum / dateD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400http://www.we-online.dePOWER-CHOKE WE-PDDATUM / DATE : 2006-01-10Würth ElektronikGeprüft / checked Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KG................................................................................................Änderung / modificationVersion 1Version 2Freigabe erteilt / general release:Kunde / customerDatum / dateUnterschrift / signature ................................................................................................................................................................Rollenspezifikation / Reel specification:Version 3Version 4Version 51,50C Gurtspezifikation / Tape specification: The force for tearing off cover tape is 10 to 130 grams in arrow directionfeeding directionThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.分销商库存信息: WURTH-ELECTRONICS 7447789215。
744225S;中文规格书,Datasheet资料
8.1 8.0 7.02012-07-172012-07-172004-10-11SStSStMSTSStSBaWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]F Typical Impedance Characteristics:H1: Classification Reflow Profile for SMT components:H2: Classification Reflow ProfilesProfile FeaturePreheat- Temperature Min (T smin ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Ramp-up rate (T L to T P )Liquidous temperature (T L )Time (t L ) maintained above T L Peak package body temperature (T p )Time within 5°C of actual peak temperature (t p )Ramp-down rate (T P to T L )Time 25°C to peak temperature Pb-Free Assembly 150°C 200°C60-180 seconds 3°C/ second max.217°C60-150 seconds See Table H320-30 seconds 6°C/ second max.8 minutes max.refer to IPC/JEDEC J-STD-020DH3: Package Classification Reflow TemperaturePB-Free Assembly PB-Free Assembly PB-Free Assembly Package Thickness< 1.6 mm 1.6 - 2.5 mm ≥ 2.5 mmVolume mm³<350260°C 260°C 250°CVolume mm³350 - 2000260°C 250°C 245°CVolume mm³>2000260°C 245°C 245°Crefer to IPC/JEDEC J-STD-020DH Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-SL2of Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Cleaning solvents which are used to clean the application might damage or change the characteristics of the component.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The soldering profile has to be complied with according to the technical reflow soldering specification, otherwise no warranty will be su-stained.•All products are supposed to be used before the end of the period of 12 months based on the transfer of title, if not a 100% solderability can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744225S。
744732681;中文规格书,Datasheet资料
2.0 1.02012-08-272010-03-15SStCZCZWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]C Schematic:F Typical Inductance vs. Current Characteristics:H4: Classification Wave Soldering Profile:H5: Classification Wave ProfileProfile FeaturePreheat- Temperature Min (T smin )- Temperature Typical (T stypical ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Δ preheat to max Temperature Peak temperature (T p )Time of actual peak temperature (t p )Ramp-down rate - Min - Typical - MaxTime 25°C to 25°C Pb-Free Assembly 100°C 120°C 130°C 70 seconds 150°C max.250°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesSn-Pb Assembly 100°C 120°C 130°C 70 seconds 150°C max.235°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesrefer to EN 61760-1:2006H Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-TISof Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data-sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Washing varnish agent that is used during the production to clean the application might damage or change the characteristics of the wire in-sulation, the marking or the plating. The washing varnish agent could have a negative effect on the long turn function of the product.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The solder profile has to be complied with according to the technical wave soldering specification, otherwise no warranty will be sustai-ned.•All products are supposed to be used before the end of the period of 12 months based on the product date-code, if not a 100% solderabi-lity can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.•Due to heavy weight of the components of size 1014, strong forces and high accelerations might have the effect to damage the electrical connection or to harm the circuit board and will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744732681。
74477510;中文规格书,Datasheet资料
Bezeichnung :description := Start of winding Marking = Inductance code33% Umgebungstemperatur / temperature:+20°CFerritMST 04-10-11NameDatum / dateÄnderung / modificationVersion 1..............................................................................................................................................................................................................................................Würth ElektronikHP 4274 A für/for L und/and Q HP 34401 A für/for R DC und I DCD Prüfgeräte / test equipment:74477510SPEICHERDROSSEL WE-PD2POWER-CHOKE WE-PD2Artikelnummer / part number :Würth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Umgebungstemp. / ambient temperature: -40°C - + 85°C Basismaterial / base material: Datum / date..............................................................................Unterschrift / signature Kontrolliert / approvednot exceed 125°C under worst case operating conditionsF Werkstoffe & Zulassungen / material & approvals:Endoberfläche / finishing electrode:Draht / wire:Sn/Cu - 99,3/0,7%2UEWF 155°CG Eigenschaften / general specifications:Betriebstemp. / operating temperature: -40°C - + 125°C Kunde / customerFreigabe erteilt / general release:E Testbedingungen / test conditions:Luftfeuchtigkeit / humidity:It is recommended that the temperature of the part does RoHS compliantLFdescription :MST 04-10-11NameDatum / dateÄnderung / modificationVersion 1Würth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Datum / dateUnterschrift / signature Würth ElektronikH Induktivitätskurve / Inductance curve :Freigabe erteilt / general release:..............................................................................................................................................................Geprüft / checked Kontrolliert / approvedKunde / customer..............................................................................................................................................................POWER-CHOKE WE-PD2DATUM / DATE : 2004-10-11description :a 330,0± 0,5mmb 20,20± 0,1mm+ 0,5- 1,0d 100,0± 1,0mmMST 04-10-11NameDatum / dateÄnderung / modificationVersion 1mm 13,00c POWER-CHOKE WE-PD2Rollenspezifikation / Reel specification:Freigabe erteilt / general release:Kunde / customer..............................................................................................................................................................Datum / dateUnterschrift / signature Würth Elektronik..............................................................................................................................................................Würth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Kontrolliert / approvedThe force for tearing off cover tape is 20 to 70 grams in arrow directionfeeding directionThis electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such as aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electronic equipments, when used in electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stage分销商库存信息: WURTH-ELECTRONICS 74477510。
74477110;中文规格书,Datasheet资料
description :A B = Start of winding 33% Umgebungstemperatur / temperature:+20°C100% SnPT 06-09-07SST05-06-22MST 04-10-11MST 03-12-10RT 03-03-03MST02-03-27JH00-12-06Name Datum / dateHP 4274 A für/for L und/and Q POWER-CHOKE WE-PDF Werkstoffe & Zulassungen / material & approvals :G Eigenschaften / general specifications :D Prüfgeräte / test equipment :E Testbedingungen / test conditions :It is recommended that the temperature of the part does 2SFBW 155°CLuftfeuchtigkeit / humidity:HP 34401 A für/for I DC und/and R DCDATUM / DATE : 2005-06-22Datum / date..................................................................................Unterschrift / signatureKontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked .................................................................................................................Kunde / customerWürth Elektronik..................................................................................Freigabe erteilt / general release:not exceed 125°C under worst case operating conditions.Basismaterial / base material: Endoberfläche / finishing electrode:Draht / wire:Umgebungstemp. / ambient temperature: -40°C - + 85°C Betriebstemp. / operating temperature: -40°C - + 125°C Anbindung an Elektrode / soldering wire to plating:Ferrit/ferrite Sn/Ag/Cu - 96.5/3.0/0.5%12,0 ± 0,312,0 ± 0,3Typ LÄnderung / modificationVersion 1Version 2Version 3Version 4Version 5Version 6Version 7• Markingdescription :PT 06-09-07SST05-06-22MST 04-10-11MST 03-12-10RT 03-03-03MST02-03-27JH00-12-06Name Datum / dateWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400POWER-CHOKE WE-PDDATUM / DATE : 2005-06-22.................................................................................................................Geprüft / checked Kontrolliert / approvedDatum / dateUnterschrift / signature Würth ElektronikH Induktivitätskurve / Inductance curve :Freigabe erteilt / general release:Kunde / customer....................................................................................................................................................................Änderung / modificationVersion 1Version 2Version 3Version 4Version 5Version 6Version 7description :A 12,7B 16,0a 330,0± 0,5mm b 20,20± 0,2mm+ 0,5- 1,0d100,0± 0,2mmPT 06-09-07SST05-06-22MST 04-10-11MST 03-12-10RT 03-03-03MST02-03-27JH00-12-06Name Datum / datePOWER-CHOKE WE-PDDATUM / DATE : 2005-06-22Gurtspezifikation / Tape specification: Rollenspezifikation / Reel specification:Freigabe erteilt / general release:Kunde / customerc 13,00mm ....................................................................................................................................................................Datum / dateUnterschrift / signature Würth Elektronik................................................................................................................. Geprüft / checked Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Änderung / modificationVersion 1Version 2Version 3Version 4Version 5Version 6Version 7The force for tearing off cover tape is10 to 130 grams in arrow directionfeeding directionThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.分销商库存信息: WURTH-ELECTRONICS 74477110。
744760310A;中文规格书,Datasheet资料
Bezeichnung :description :Größe / size 0805A 2,0 ± 0,2mmB 1,25 ± 0,2mmC 1,2 ± 0,2mmD 0,5 ref.mm F 0,4 ± 0,1mm H 1,2mm I 0,925mm J0,75mm60 70%25°CFerrit/ ferrite SKleVersion 207-01-17SkleVersion 106-07-07Name Änderung / modificationDatum / dateWürth ElektronikENA 5071B für/for SRFD Prüfgeräte / test equipment:Agilent 4287A + HP 16193A für/for L und/and Q HP 4338B für/for R DCHP 4285A + 42841A + 42842C + 42851-6110 für/for I DC A Mechanische Abmessungen / dimensions:Kunde / customerFerrite-SMD-Inductor WE-RFID-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Betriebstemperatur / operating temperature: -40°C ~ +85°C Kunde / customerFreigabe erteilt / general release:..........................................................................................................................................................................................................DATUM / DATE : 2007-01-17Datum / date..............................................................................Unterschrift / signature Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGLagerbedingungen / storage conditions: -10°C ~ + 40°C 30 ~ 70% RHF Werkstoffe & Zulassungen / material & approvals:Kontaktmaterial / contact plating:Ag/Pd + Ni + SnBasismaterial / base material: E Testbedingungen / test conditions:Umgebungstemperatur / ambient temperature: -40°C ~ + 70°C Luftfeuchtigkeit / humidity:Umgebungstemperatur / temperature:G Eigenschaften / general specifications:This electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine,transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.SEITE 1 VON 1/分销商库存信息: WURTH-ELECTRONICS 744760310A。
7447015;中文规格书,Datasheet资料
7.1 7.0 6.02012-06-272012-05-032009-12-01SStSStCZSStCZWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]H4: Classification Wave Soldering Profile:H5: Classification Wave ProfileProfile FeaturePreheat- Temperature Min (T smin )- Temperature Typical (T stypical ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Δ preheat to max Temperature Peak temperature (T p )Time of actual peak temperature (t p )Ramp-down rate - Min - Typical - MaxTime 25°C to 25°C Pb-Free Assembly 100°C 120°C 130°C 70 seconds 150°C max.250°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesSn-Pb Assembly 100°C 120°C 130°C 70 seconds 150°C max.235°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesrefer to EN 61760-1:2006H Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-FIof Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data-sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Washing varnish agent that is used during the production to clean the application might damage or change the characteristics of the wire in-sulation, the marking or the plating. The washing varnish agent could have a negative effect on the long turn function of the product.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The solder profile has to be complied with according to the technical wave soldering specification, otherwise no warranty will be sustai-ned.•All products are supposed to be used before the end of the period of 12 months based on the product date-code, if not a 100% solderabi-lity can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 7447015。
744761133C;中文规格书,Datasheet资料
Bezeichnung :description :Größe / size 0603CA 1,65 ± 0,2mmB 1,15 ± 0,2mmC 0,9 ± 0,2mmD 0,5 ref.mmF 0,30 ± 0,1mm H 0,762mm I 0,625mm J0,65mmEigenschaften / properties Wert / valueEinheit / unittol.Induktivität /inductance Güte Q /Q factorDC-Widerstand /DC-resistance Nennstrom /rated currentEigenres.-Frequenz /self-res.-frequency60 … 70%25°CKeramik/ ceramic HBH Version 311-08-29ESVersion 210-08-27SkleVersion 106-11-27Name Änderung / modificationDatum / dateL max.2300MHzSRFWürth Elektronik250 MHz∆T = 15 K250 MHz min.R DCmin.nHENA 5071B für/for SRFQ 36I DC D Prüfgeräte / test equipment:Agilent 4287A + HP 16193A für/for L und/and Q HP 4338B für/for R DCHP 4285A + 42841A + 42842C + 42851-6110 für/for I DC 600 A Mechanische Abmessungen / dimensions:Kunde / customer :744761133CCeramic-SMD-Inductor WE-KIArtikelnummer / part number :D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checkedBetriebstemperatur / operating temperature: -40°C ~ +125°C Kunde / customerFreigabe erteilt / general release:.........................................................................................................................................................................................................Spezifikation für Freigabe / specification for releaseDATUM / DATE : 2011-08-29max.mA Datum / date...............................................................................Unterschrift / signature Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGLagerbedingungen / storage conditions: -10°C ~ + 40°C 30 ~ 70% RHF Werkstoffe & Zulassungen / material & approvals:Kontaktmaterial / contact plating:Ag + Ni + AuBasismaterial / base material: C Lötpad / soldering spec.:B Elektrische Eigenschaften / electrical properties:E Testbedingungen / test conditions:Testbedingungen / test conditions0,20±5%33Umgebungstemperatur / ambient temperature: -40°C ~ + 110°C Luftfeuchtigkeit / humidity:Umgebungstemperatur / temperature:G Eigenschaften / general specifications:IJ IHAFBCThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety andreliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.LFSEITE 1 VON 1/分销商库存信息: WURTH-ELECTRONICS 744761133C。
74457068;中文规格书,Datasheet资料
33% Umgebungstemperatur / temperature:+20°CMST 2004-10-11NameDatum / dateÄnderung / modificationVersion 1Freigabe erteilt / general release:Kunde / customerWürth Elektronik..................................................................................Ferrit/ferrite 2UEWF 155°C F Werkstoffe & Zulassungen / material & approvals :G Eigenschaften / general specifications :D Prüfgeräte / test equipment :E Testbedingungen / test conditions :It is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions.Umgebungstemp. / ambient temperature: -40°C - + 85°C Basismaterial / base material:Draht / wire: Datum / date............................................................................Unterschrift / signature Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked ..................................................................................................................................Sockel/ base:UL94V-0Pin / Terminal100% SnBetriebstemp. / operating temperature: -40°C - + 125°C HP 4274 A für/for L und/and Q HP 34401 A für/for I DC und/and R DCLuftfeuchtigkeit / humidity:• R90description :Name Datum / dateÄnderung / modificationPOWER-CHOKE WE-PD 4DATUM / DATE : 2004-10-11H Induktivitätskurve / Inductance curve :Freigabe erteilt / general release:Kunde / customer..............................................................................................................................................................Geprüft / checked Kontrolliert / approvedDatum / dateUnterschrift / signature Würth ElektronikWürth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400..............................................................................................................................................................description :a 330,0± 2,0mmb 21,00± 0,8mmc 13,00± 0,5mmd 100,0± 2,0mmMST 2004-10-11NameDatum / dateRollenspezifikation / Reel specification:Änderung / modificationVersion 1Geprüft / checked Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Würth Elektronik..................................................................................................................................................................................................................................................................................................Datum / dateUnterschrift / signature Freigabe erteilt / general release:Kunde / customerPOWER-CHOKE WE-PD 4feeding directionThe force for tearing off cover tape is 20 to 70 grams in arrow directionThis electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such as aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electronic equipments, when used in electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stage.分销商库存信息: WURTH-ELECTRONICS 74457068。
74477130;中文规格书,Datasheet资料
description :33% Umgebungstemperatur / temperature:+20°C100% SnSST05-06-22MST 04-10-11MST 03-12-10RT 03-03-03MST02-03-27JH 00-12-06NameDatum / dateÄnderung / modificationVersion 1Version 2Version 3Version 4Version 5Version 6not exceed 125°C under worst case operating conditions.Basismaterial / base material: Endoberfläche / finishing electrode:Draht / wire:Umgebungstemp. / ambient temperature: -40°C - + 85°C Betriebstemp. / operating temperature: -40°C - + 125°C Anbindung an Elektrode / soldering wire to plating:Ferrit/ferrite Sn/Ag/Cu - 96.5/3.0/0.5%Kunde / customerWürth Elektronik..................................................................................Freigabe erteilt / general release:Datum / date.................................................................................Unterschrift / signature Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked ............................................................................................................It is recommended that the temperature of the part does 2SFBW 155°CLuftfeuchtigkeit / humidity:HP 34401 A für/for I DC und/and R DCF Werkstoffe & Zulassungen / material & approvals :G Eigenschaften / general specifications :D Prüfgeräte / test equipment :E Testbedingungen / test conditions :HP 4274 A für/for L und/and Q POWER-CHOKE WE-PD• Markingdescription :SST05-06-22MST 04-10-11MST 03-12-10RT 03-03-03MST02-03-27JH 00-12-06NameDatum / dateÄnderung / modificationVersion 1Version 2Version 3Version 4Version 5Version 6 H Induktivitätskurve / Inductance curve :Freigabe erteilt / general release:Kunde / customer...................................................................................................................................................................Kontrolliert / approvedDatum / dateUnterschrift / signature Würth ElektronikWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400POWER-CHOKE WE-PDDATUM / DATE : 2005-06-22............................................................................................................Geprüft / checkeda 330,0± 0,5mmb 20,20± 0,2mm+ 0,5- 1,0d100,0± 0,2mmSST05-06-22MST 04-10-11MST 03-12-10RT 03-03-03MST02-03-27JH 00-12-06NameDatum / dateVersion 5Version 6Version 1Version 2Version 3Version 4 Geprüft / checked Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Änderung / modificationWürth Elektronik...............................................................................................................................................................................................................................................................................Datum / dateUnterschrift / signature Rollenspezifikation / Reel specification:Freigabe erteilt / general release:Kunde / customerc 13,00mm The force for tearing off cover tape is10 to 130 grams in arrow directionfeeding directionThis electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such as aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electronic equipments, when used in electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stage.xxx xxx分销商库存信息: WURTH-ELECTRONICS 74477130。
744227;中文规格书,Datasheet资料
8.1 8.0 7.02012-07-172012-07-172004-10-11SStSStMSTSStSBaWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]F Typical Impedance Characteristics:H1: Classification Reflow Profile for SMT components:H2: Classification Reflow ProfilesProfile FeaturePreheat- Temperature Min (T smin ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Ramp-up rate (T L to T P )Liquidous temperature (T L )Time (t L ) maintained above T L Peak package body temperature (T p )Time within 5°C of actual peak temperature (t p )Ramp-down rate (T P to T L )Time 25°C to peak temperature Pb-Free Assembly 150°C 200°C60-180 seconds 3°C/ second max.217°C60-150 seconds See Table H320-30 seconds 6°C/ second max.8 minutes max.refer to IPC/JEDEC J-STD-020DH3: Package Classification Reflow TemperaturePB-Free Assembly PB-Free Assembly PB-Free Assembly Package Thickness< 1.6 mm 1.6 - 2.5 mm ≥ 2.5 mmVolume mm³<350260°C 260°C 250°CVolume mm³350 - 2000260°C 250°C 245°CVolume mm³>2000260°C 245°C 245°Crefer to IPC/JEDEC J-STD-020DH Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-SL2of Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Cleaning solvents which are used to clean the application might damage or change the characteristics of the component.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The soldering profile has to be complied with according to the technical reflow soldering specification, otherwise no warranty will be su-stained.•All products are supposed to be used before the end of the period of 12 months based on the transfer of title, if not a 100% solderability can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744227。
744777122;中文规格书,Datasheet资料
description :33% Umgebungstemperatur / temperature:+20°C100% SnMST04-10-11JH 00-12-06NameDatum / dateD-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Änderung / modification.................................................................................................Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co.KGE Testbedingungen / test conditions :Freigabe erteilt / general release:Kunde / customerWürth Elektronik........................................................................Umgebungstemp. / ambient temperature: -40°C - + 85°C Basismaterial / base material: Endoberfläche / finishing electrode:G Eigenschaften / general specifications :D Prüfgeräte / test equipment :Betriebstemp. / operating temperature: -40°C - + 125°C Luftfeuchtigkeit / humidity:HP 4274 A für/for L und/and Q HP 34401 A für/for I DC und/and R DCF Werkstoffe & Zulassungen / material & approvals :POWER-CHOKE WE-PDVersion 1Version 2 Datum / dateIt is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions...............................................................................Unterschrift / signature Draht / wire:2SFBW 155°CAnbindung an Elektrode / soldering wire to plating:Sn/Ag/Cu - 96.5/3.0/0.5%Ferrit/ferritedescription :POWER-CHOKE WE-PDDATUM / DATE : 2004-10-11H Induktivitätskurve / Inductance curve :MST04-10-11JH 00-12-06NameDatum / dateVersion 2Version 1Würth ElektronikFreigabe erteilt / general release:Kunde / customerDatum / dateUnterschrift / signature .....................................................................................................................................................................................................Würth Elektronik eiSos GmbH & Co.KGÄnderung / modification..................................................Geprüft / checked Kontrolliert / approvedD-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400description :POWER-CHOKE WE-PD..........................................................................................................................................................MST04-10-11.................................................................................................JH 00-12-06NameDatum / dateVersion 1Version 2 Kunde / customerWürth ElektronikKontrolliert / approvedUnterschrift / signature Datum / dateGeprüft / checked Freigabe erteilt / general release:Änderung / modificationWürth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400The force for tearing off cover tape is 10 to 130 grams in arrow direction165 to 180°feeding directionThis electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such as aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electronic equipments, when used in electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stage分销商库存信息: WURTH-ELECTRONICS 744777122。
744242110;中文规格书,Datasheet资料
4.1 4.0 3.02012-07-172012-07-172006-02-08SStSStMSTSStSBaWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]F Typical Impedance Characteristics:H1: Classification Reflow Profile for SMT components:H2: Classification Reflow ProfilesProfile FeaturePreheat- Temperature Min (T smin ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Ramp-up rate (T L to T P )Liquidous temperature (T L )Time (t L ) maintained above T L Peak package body temperature (T p )Time within 5°C of actual peak temperature (t p )Ramp-down rate (T P to T L )Time 25°C to peak temperature Pb-Free Assembly 150°C 200°C60-180 seconds 3°C/ second max.217°C60-150 seconds See Table H320-30 seconds 6°C/ second max.8 minutes max.refer to IPC/JEDEC J-STD-020DH3: Package Classification Reflow TemperaturePB-Free Assembly PB-Free Assembly PB-Free Assembly Package Thickness< 1.6 mm 1.6 - 2.5 mm ≥ 2.5 mmVolume mm³<350260°C 260°C 250°CVolume mm³350 - 2000260°C 250°C 245°CVolume mm³>2000260°C 245°C 245°Crefer to IPC/JEDEC J-STD-020DH Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-SLMof Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Cleaning solvents which are used to clean the application might damage or change the characteristics of the component.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The soldering profile has to be complied with according to the technical reflow soldering specification, otherwise no warranty will be su-stained.•All products are supposed to be used before the end of the period of 12 months based on the transfer of title, if not a 100% solderability can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744242110。
744772471;中文规格书,Datasheet资料
6.0 5.02012-08-272006-05-05SStSStCZWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]C Schematic:F Typical Inductance vs. Current Characteristics:H4: Classification Wave Soldering Profile:H5: Classification Wave ProfileProfile FeaturePreheat- Temperature Min (T smin )- Temperature Typical (T stypical ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Δ preheat to max Temperature Peak temperature (T p )Time of actual peak temperature (t p )Ramp-down rate - Min - Typical - MaxTime 25°C to 25°C Pb-Free Assembly 100°C 120°C 130°C 70 seconds 150°C max.250°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesSn-Pb Assembly 100°C 120°C 130°C 70 seconds 150°C max.235°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesrefer to EN 61760-1:2006H Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-TISof Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data-sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Washing varnish agent that is used during the production to clean the application might damage or change the characteristics of the wire in-sulation, the marking or the plating. The washing varnish agent could have a negative effect on the long turn function of the product.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The solder profile has to be complied with according to the technical wave soldering specification, otherwise no warranty will be sustai-ned.•All products are supposed to be used before the end of the period of 12 months based on the product date-code, if not a 100% solderabi-lity can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.•Due to heavy weight of the components of size 1014, strong forces and high accelerations might have the effect to damage the electrical connection or to harm the circuit board and will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744772471。
744761215C;中文规格书,Datasheet资料
Bezeichnung :description :Größe / size 0603CA 1,65 ± 0,2mmB 1,15 ± 0,2mmC 0,9 ± 0,2mmD 0,5 ref.mmF 0,30 ± 0,1mm H 0,762mm I 0,625mm J0,65mmEigenschaften / properties Wert / valueEinheit / unittol.Induktivität /inductance Güte Q /Q factorDC-Widerstand /DC-resistance Nennstrom /rated currentEigenres.-Frequenz /self-res.-frequency60 … 70%25°CKeramik/ ceramic HBH Version 311-07-11ESVersion 210-08-27SkleVersion 106-11-27Name Änderung / modificationDatum / dateUmgebungstemperatur / ambient temperature: -40°C ~ + 110°C Luftfeuchtigkeit / humidity:Umgebungstemperatur / temperature:G Eigenschaften / general specifications:Basismaterial / base material: C Lötpad / soldering spec.:B Elektrische Eigenschaften / electrical properties:E Testbedingungen / test conditions:Testbedingungen / test conditions0,85±5%150Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGLagerbedingungen / storage conditions: -10°C ~ + 40°C 30 ~ 70% RHF Werkstoffe & Zulassungen / material & approvals:Kontaktmaterial / contact plating:Ag + Ni + Au..................................................................................Spezifikation für Freigabe / specification for releaseDATUM / DATE : 2011-07-11max.mA Datum / date...............................................................................Unterschrift / signature Ceramic-SMD-Inductor WE-KIArtikelnummer / part number :D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checkedBetriebstemperatur / operating temperature: -40°C ~ +125°C Kunde / customerFreigabe erteilt / general release:....................................................................................................................... A Mechanische Abmessungen / dimensions:Kunde / customer :744761215CENA 5071B für/for SRFQ 30I DC D Prüfgeräte / test equipment:Agilent 4287A + HP 16193A für/for L und/and Q HP 4338B für/for R DCHP 4285A + 42841A + 42842C + 42851-6110 für/for I DC 280Würth Elektronik150 MHz∆T = 15 K100 MHz min.R DCmin.nHL max.990MHzSRFIJ IHAFBCThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety andreliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.LFSEITE 1 VON 1/分销商库存信息: WURTH-ELECTRONICS 744761215C。
7447779215;中文规格书,Datasheet资料
Bezeichnung :description := Start of winding Marking = Inductance code33% Umgebungstemperatur / temperature:+20°C100% SnMST 08-01-04MST 04-10-11SST04-07-28SST 04-04-21SST 04-04-15MST 03-12-10AG02-11-05AG 02-05-14NameDatum / dateVersion 10Änderung / modificationVersion 2Version 3Version 4Version 5Version 6Version 7Version 8 Luftfeuchtigkeit / humidity:HP 4274 A für/for L und/and Q E Testbedingungen / test conditions :Kunde / customer :SPEICHERDROSSEL WE-PDPOWER-CHOKE WE-PDArtikelnummer / part number :7447779215Anbindung an Elektrode / soldering wire to plating:Sn/Ag/Cu - 96.5/3.0/0.5%Draht / wire:2SFBW; 155°Umgebungstemp. / ambient temperature: -40°C - + 85°C F Werkstoffe & Zulassungen / material & approvals :G Eigenschaften / general specifications :D Prüfgeräte / test equipment :.................................................HP 34401 A für/for I DC und/and R DCDatum / date.............................................................................Unterschrift / signature Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked ...............................................not exceed 125°C under worst case operating conditions.Ferrit/ferrite Würth Elektronik..................................................................................Betriebstemp. / operating temperature: -40°C - + 125°C Freigabe erteilt / general release:Kunde / customerBasismaterial / base material: Endoberfläche / finishing electrode:It is recommended that the temperature of the part doesBezeichnung :description :H Induktivitätskurve / Inductance curve :MST 08-01-04MST 04-10-11SST04-07-28SST 04-04-21SST 04-04-15MST 03-12-10AG02-11-05AG 02-05-14NameDatum / dateÄnderung / modificationVersion 2Version 3Version 4Version 5Version 6Version 7Version 8Version 10Würth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400................................................................................................Geprüft / checked Kontrolliert / approvedDatum / dateUnterschrift / signature Würth ElektronikFreigabe erteilt / general release:Kunde / customer...............................................................................................................................................................POWER-CHOKE WE-PDDATUM / DATE : 2008-01-04Kunde / customer :Bezeichnung :description :a 330,0± 2,0mmb 21,00± 0,8mmc 13,00± 0,5mmd 100,0± 1,0mmMST 08-01-04MST 04-10-11SST04-07-28SST 04-04-21SST 04-04-15MST 03-12-10AG02-11-05AG 02-05-14NameDatum / dateVersion 7Version 8Version 10Version 3Version 4Version 5Version 6Würth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400................................................................................................Geprüft / checked Kontrolliert / approvedÄnderung / modificationVersion 2Datum / dateUnterschrift / signature Würth ElektronikFreigabe erteilt / general release:Kunde / customer...............................................................................................................................................................Rollenspezifikation / Reel specification:POWER-CHOKE WE-PDKunde / customer :The force for tearing off cover tape is 10 to 130 grams in arrow direction165 to 180°This electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control),transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.分销商库存信息: WURTH-ELECTRONICS 7447779215。
744314760;中文规格书,Datasheet资料
T [ °C ]
70,00
60,00
50,00
40,00
30,00
20,00
10,00
0,00
0
1
2
3
4
5
6
7
Current (A)
Freigabe erteilt / general release:
Kunde / customer
..................................................................................
A
7,3 ± 0,1
mm
G
B
12,0 ± 0,1
mm
C
H
W
D
E
F
T
G
I
J
W
min.
mm
1,5
+ 0,1
1,5 - 0,0
mm
4,0 ± 0,1
mm
2,0 ± 0,1
mm
1,75 ± 0,1
mm
7,6 ± 0,1
mm
5,2 ± 0,1
mm
16,0 ± 0,3
mm
J
a
b
Rollenspezifikation / Reel specification:
a
330,0 ± 2,0
mm
d
b
21,0 ± 0,8
mm
c
13,00 ± 0,5
mm
d
100,0 ± 1,5
mm
Øc 150
The Force for tearing off cover tape is 20 to 70 grams in arrow direction
744762182A;中文规格书,Datasheet资料
Bezeichnung :description :Größe / size 1008A 2,5 ± 0,2mmB 2,0 ± 0,2mmC 1,6 ± 0,2mmD 0,5 ref.mm F 0,5 ± 0,1mm H 2,2mm I 0,9mm J1,2mm60 … 70%25°CKeramik/ ceramic AWe Version 104-10-11NameÄnderung / modificationDatum / dateWürth ElektronikENA 5071B für/for SRFD Prüfgeräte / test equipment:Agilent 4287A + HP 16193A für/for L und/and Q HP 4338B für/for R DCHP 4285A + 42841A + 42842C + 42851-6110 für/for IDC Lagerbedingungen / storage conditions: -10°C ~ + 40°C 30 ~ 70% RHF Werkstoffe & Zulassungen / material & approvals:A Mechanische Abmessungen / dimensions:Kunde / customer:744762182AKeramik-SMD-Induktivität WE-KI Ceramic-SMD-Inductor WE-KIArtikelnummer / part number :D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Betriebstemperatur / operating temperature: -40°C ~ +125°C Kunde / customerFreigabe erteilt / general release:...................................................................................................................................................................................................Spezifikation für Freigabe / specification for releaseDATUM / DATE : 2004-10-11Datum / date.............................................................................Unterschrift / signatureKontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGKontaktmaterial / contact plating:Mo/Mn + Ni + AuBasismaterial / base material: E Testbedingungen / test conditions:Umgebungstemperatur / ambient temperature: -40°C ~ + 110°C Luftfeuchtigkeit / humidity:Umgebungstemperatur / temperature:G Eigenschaften / general specifications:This electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such asaerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electronic equipments, when us electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stageRoHS compliantLFSEITE 1 VON 1/分销商库存信息: WURTH-ELECTRONICS 744762182A。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Bezeichnung :description :
Größe / size 0805C
A 2,28±0,2mm
B 1,70±0,2mm
C 1,28±0,2mm
D 0,50 ref mm F 0,51 ref mm H 1,78 ref mm I 1,02 ref mm J
0,76 ref mm
B Elektrische Eigenschaften / electrical properties :
Eigenschaften / properties Wert / value
Einheit / unit
tol.Induktivität /inductance Güte Q /Q factor
DC-Widerstand /DC-resistance Nennstrom /rated current
Eigenres.-Frequenz /self-res.-frequency
E Testbedingungen / test conditions :
Luftfeuchtigkeit / humidity:
33% Umgebungstemperatur / temperature:
+20°C
G Eigenschaften / general specifications :
Keramik/ ceramic Lagerbedingungen / Storage conditions: -10°C ~ +40 °C 30 ~70 % RH Betriebstemperatur / operating temperature: -40°C - +125°C
HBH Version 411-07-11ES Version 310-08-27Skle
Version 207-01-17Skle
Version 1
08-03-06
Name Änderung / modification
Datum / date
ktronik eiSos GmbH & Co. KG
Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400
min.
R DC
min.L max.250 MHz
∆T = 15 K
100 MHz MHz
..........................................................
.............................................................................................................................................
Würth Elektronik
Ceramic-SMD-Inductor WE-KI
Kontaktmaterial/ contact plating
Freigabe erteilt / general release:
A Mechanische Abmessungen / dimensions :
±5%150nH
Q 40Artikelnummer / part number :Geprüft / checked 920
SRF
Datum / date
...........................................................................Unterschrift / signature Kontrolliert / approved
Spezifikation für Freigabe / specification for release
DATUM / DATE : 2011-07-11
max.
mA Testbedingungen / test conditions
Kunde / customer :
744760215C
Basismaterial / base material:F Werkstoffe & Zulassungen / material & approvals
ENA 5071B für/for SRF
D Prüfgeräte / test equipment :
Agilent 4287A +HP 16193A für/for L und/and Q HP 4338B für/for R DC
C Lötpad / soldering spec.:
Ag + Ni + Au
Kunde / customer
0,56I DC HP 4285A + 42841A + 42842C + 42851 - 6110 für/for I DC 400
I
J I
H
This electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and
reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
LF
A
F
B
D
C
SEITE 1 VON 1
/
分销商库存信息: WURTH-ELECTRONICS 744760215C。