螺旋伞齿轮外文术语

合集下载

与齿轮相关地英语词汇总情况结

一．齿轮gear行星齿轮planetary gear/planet gear/epicyclic gear小齿轮pinion大齿轮wheel/gear主动齿轮driving gear从动齿轮driven gear太阳轮sun gear直齿轮spur gear斜齿轮helical gear锥齿轮bevel gear外齿轮external gear内齿轮internal gear外直齿轮external spur gear内直齿轮internal spur gear圆柱齿轮cylindrical gear螺旋锥齿轮sprial bevel gear直齿锥齿轮straight bevel gear斜齿锥齿轮helical bevel gear弧齿锥齿轮spiral bevel gear圆柱齿弧锥齿轮sprial bevel gear with circle arc tooth profile 8字啮合锥齿轮octoid gear锥齿轮当量圆柱齿轮virtual cylindrical gear of bevel gear曲面齿锥齿轮curved tooth bevel gear摆线齿锥齿轮enicycloid bevel gear零度锥齿齿轮zerot bevel gear冠轮crown gear链轮sprocket人字齿轮double helical gear配对齿轮/啮合齿轮mating gear端面齿轮contrate gear准双曲面齿轮hypoid gear椭圆齿轮elliptical gear非圆齿轮non-circular gear变位齿轮X-gears/gears with addendum modification 非变位齿轮X-gero gear标准齿轮standard gear产形齿轮generating gear渐开线齿轮involute cylindrical gear针轮cylindsical tan tein gear/pin-wheel柔性齿轮flexspine刚性齿轮circular spline摆线齿轮cycloidal gear圆弧齿轮circular-arc gear/W-N gear双圆弧齿轮double-circular-arc gear皮带轮belt wheel减速器齿轮speed reducer gear减速箱positive speed gearbox前末端齿轮front terminal end gear双齿轮double gear人字齿轮、双螺旋齿轮herring bone gear输出轴（取力器）power take off shaft角磨机angle grinder蜗轮worm wheel蜗杆worm锥蜗轮spiroid gear锥蜗杆spiroid锥蜗轮蜗杆spiroid gear pair锥蜗杆spiroid平面蜗杆planar worm wheel; IP-worm wheel 圆柱蜗杆cylindrical worm环面蜗杆enveloping worm圆弧圆柱蜗杆ZC-worm锥面包络圆柱蜗杆ZK-worm法向直廓蜗杆ZN-worm平面包络环面蜗轮planar double锥面包络环面蜗杆TK-worm wheel渐开线包络环面蜗杆TI-worm平面二次包络蜗杆TP-worm变速箱transmission轴和套shaft and sleeve二．渐开线involute 花键spline渐开线外花键external involute spline渐开线内花键internal involute spline渐开线公差involute tolerance花键齿节距spline pitch(花键)外径/大径major diameter(花键)内径/小径minor diameter成形直径form diameter花键类型：a. flat root,side fit 平根，齿侧配合b. fillet root,side fit 齿根圆角，齿侧配合Product series:Spur gear, bevel gear, spiral bevel gear, internal gear, sprocket, transmission, reducer, shaft and sleeve etc.(直齿轮，斜齿轮，伞齿轮，螺旋伞齿轮，内齿轮，链轮，变速箱，减速箱，轴类，套类) 30/40 型刮板运输机：type 30/40 scraper conveyor取力器前后壳：power take before and after the shell花键轴：spline shaft变速箱取力器总成及配件：transmission power take off assembly and accessories秸秆粉碎机齿轮：straw grinder gear (straw crusher)旋耕机：rotary拖拉机：tractor前驱动桥：front drive axle拖拉机前驱动桥总成及配件：tractor front drive axle assembly and parts玉米联合收割机: corn combine harvester割台箱：box header玉米联合收获机割台箱总成及配件：corn combine harvester header box assembly and parts.斯太尔汽车：Steyr automobile中桥：vehicle bridge驱动桥：driving axle后桥：rear axle齿轮加工，滚齿，磨齿，剃齿，插齿：gear machining, hobbing, grinding teeth, shaving, slotting农机厂：agricultural machinery plant矿山机械厂：mining machinery factory弧齿锥齿轮铣齿机，滚齿机，磨齿机，剃齿机，数控车床，精密磨床，花键磨床，平面磨床，卧式拉床等：sprial bevel gear milling machine, hobbing machine, grinding machine, gear shaving machine, CNC lathes, precision grinding, spline grinding machine, surface grinder, horizontal broaching machine and so on.Numerical control lathes 数控车床Black oxide 黑氧化Sprial bevel gear axle螺旋伞齿轮轴三．常见其他词汇齿数number of teeth/teeth guantity 当量齿数virtual number of teeth头数number of starts/threads齿顶crest/top land比率ratio齿圈ring gear螺纹thread螺纹孔tapped holes毛边，毛刺burr心轴arbor齿条rack基本齿条basic rack产形齿条counterpart rack直齿条spur rack斜齿条helical rack基本齿条类型basic rack type (heel end 末端) 轴承bearing半轴half-axle离合器clutch刀片blade毛坯blank卡盘chuck圈lap刀盘cutter切齿干涉cutter reference刀具半径cutter radius刀刃圆角半径cutter edge radius传感器sensor大端接触heel pattern与成对轮齿大端接触heel pattern with the pair gear tooth 齿锥度tooth taper打字joined tooth gear lettering中凸齿barrel-shaped teeth四．关联词汇基圆base circle基圆直径base diameter基节base pitch基圆半径base radius节圆pitch circle节圆直径pitch diameter 径节diametral pitch 节线pitch line节线跳动pitchline runout分度圆reference circle分度圆直径reference diameter根圆root circle根圆直径root diameter顶圆tip circle顶圆直径tip diameter顶隙圆clearance circle周节circular pitch外径outside diameter齿根圆dedendum circle齿根直径root diameter齿根圆角半径(过滤圆角半径) fillet radius背锥back cone面锥face cone节锥pitch cone根锥root cone分锥reference cone分锥顶点reference cone apex齿顶高addendum齿根高dedendum全齿高whole depth齿高tooth depth/height弦齿高chordal height固定弦齿高constant chord height齿宽face width有效齿宽effective width齿厚tooth thickness端面齿厚transerse tooth thickness法向齿厚normal tooth thickness端面基圆齿厚transverse base thickness法向基圆齿厚normal base thickness弦齿厚chordal thickness/arc tooth thickness 端面弦齿厚transverse chordal tooth thickenss 固定弦齿厚constant chord弧齿厚circular thickness前锥面front cone中锥面middle cone背锥面back cone背锥母线backcone element总误差total accumulated spacing error五．角angle背锥角back (cone) angle面锥角face angle节锥角pitch angle根锥角root angle分锥角reference cone angle顶锥角tip angle齿锥角tooth cone angle压力角pressure angle主压力角main pressure angle轴交角shaft angle齿顶角addendum angle齿根角dedendum angle传动轴角transmission axes angle螺旋角spiral angle任意点螺旋角spiral angle at a point重点螺旋角mean spiral angle大端螺旋角outer spiral angle小端螺旋角inner spiral angle齿形角nominal pressure angle倒角chamfer啮合角working pressure angle齿宽角width angle工作压力角pressure angle (operating)齿厚半角tooth thickness half angle槽宽半角space width half angle任意点压力角pressure angle at a point任意点法向压力角normal pressure angle at a point任意点端面压力角transverse pressure angle at a point总作用角total angle of transmission导程角lead angle端面作用角transverse angle of transmission纵向作用角overlap angle轮廓有效位置渐开线绞孔角度the evolvent reaming angle of the profile active site 有效面积渐开线展开轮廓角度the angle developed profile of involute of the active area六．距distance齿距pitch齿距公差pitch tolerance锥距cone distance外锥距outer cone distance内锥距inner cone distance内锥距inner cone distance重(中)点锥距mean cone distance背锥距back cone distance背角距back angle distance花键齿节距spline pitch中心距centre distance标准中心距reference centre distance实际中心距center distance (operating)位置距offset冠顶距apex to crown轮冠距tip distance/crown to back安装距mounting distance/locating distance 齿端距angular pitch工具头部刀顶距point width of the tool head七．齿面flank齿面tooth flank右侧齿面right flank左侧齿面lefe flank同侧齿面corresponding flank异侧齿面opposite flank上齿面addendum flank下齿面dedendum flank工作齿面working flank非工作齿面non-working flank啮合齿面mating flank共轭齿面conjugate flank可用齿面usable flank有效齿面active flank产形齿面generating flank八．面齿顶面face齿根面flank阿基米德螺旋面screw helicoid球面渐开螺旋面spherical involute 定位面locating face凸面convex side凹面concace face圆环面tosoid齿根圆环面root tosoid分度圆环面reference tosoid圆环面的母圈generant of the tosoid圆环面的中性圈middle circle of the tosoid 圆环面的中间平面middle plane of the tosoid 圆环面的内圈inner circle of the tosoid基准平面datum plane轴平面axial plane节平面pitch plane端平面transverse plane法平面normal plane啮合平面plane of action中平面middle plane喉平面gorge plane咽喉面gorge咽喉半径gorge radius喉圆gorge circle齿根过渡曲面fillet啮合曲面surface of action分度曲面reference surface 节曲面pitch surface齿顶曲面tip surface齿根曲面root surface假想曲面imaginary surface 分度圆柱面reference cylinder 节圆柱面pitch cylinder基圆柱面basic cylinder齿顶圆柱面tip cylinder齿根圆柱面root cylinder九．线齿线tooth trace渐开线involute延伸渐开线prolate involute 缩短渐开线curtate involute 球面渐开线spherical involute渐开螺旋线involute helicoid螺旋线helix分度圆涡旋线reference helix圆锥螺旋线conical spiral阿基米德螺旋线archimedes spiral基准线datum line连心线line of centres摆线cycloid长幅摆线prolate cycloid短幅摆线curtate cycloid内摆线hypo cycloid外摆线epoi cycloid长幅外摆线prolate epoicycloid长幅内摆线prolate hypocycloid短幅外摆线curtate epoicycloid短幅内摆线curtate hypocycloid瞬时接触线line of contact端面啮合线transverse path of contact十．啮合啮合齿轮mating gear啮合平面plane of action啮合曲面surface of action相啮齿面mating flank啮合干涉meshing interefence 啮合区域zone of action啮合角working pressure angle十一. PitchPitch 齿距Pitch tolerance 齿距公差Pitch circle 节圆Pitch diameter 节圆直径Pitch line 节线Pitch point 节点Pitch plane 节平面Pitch surface 节曲面Pitch cylinder 节圆柱面Pitch cone 节锥Pitch cone angle 节锥角十二. Tooth/teethTooth type 齿形Tooth trace direction 齿向：a) right-hand teeth 左旋齿b) left –hand teeth 右旋齿tooth crown 齿冠tooth trace 齿线tooth tip 齿棱tooth depth 齿高tooth flank 齿面tooth profile 齿廓tooth space 齿槽tooth guantity 齿数pitch 齿距齿根bottom land十三. 顶公共锥顶common apex十四. 模数模数module端面模数transverse module外端面模数exterior transverse module 法向模数normal module轴向模数axial module平均正常模数average normal modle 十五. 比（率）/重合度齿数比gear ratio传动比transmission ratio总重合度total contact ratio端面重合度transverse ratio纵向重合度overlap ratio精确度accuracy degree修正度degree of correction十六齿廓( profile)齿廓tooth profile齿廓型修profile modification端面齿廓transverse profile法向齿廓normal profile法基本齿廓normal basic rack profile轴向齿廓axial profile背锥齿廓back cone tooth profile基本齿廓basic tooth profile十七. 系数（coefficient）变位系数modification coefficient/shifting coefficient切向变为系数tangential MC齿顶系数、顶隙系数addendum coefficient /bottom clearance coefficient 径向变位系数addendum modification coefficient中心距变位系数centre distance modification coefficient径向间隙系数radial clearance factor头部厚度系数coefficient of head thickness过滤曲线弯曲半径系数factor of radius of curvature of transition curve齿厚变化系数coefficient of tooth thickness change十八. 量（公差/偏差）齿线偏移量offset of tooth trace容许加铅量lead tolerance变位量addendum modification渐开线公差involute tolerance内轴距测量极限偏差limit deviations of measuring interaxle distance报废限度bore condemning limit全程中成对轴角测量偏差余量allowance for variation of measuring pair axes angle of one tooth轴向运动测量偏差varation tolerance of the measurement axial movement十九. 隙顶隙(bottom) clearance齿侧背隙backlash周圆侧隙circumferential blacklash法向侧隙normal backlash径向侧隙radial backlash最小侧间隙min side clearance二十. 厚齿厚tooth thickness端面齿厚transverse tooth thickness法向齿厚normal tooth thickness端面齿顶厚crest width法向齿顶厚normal crest width弦齿厚chordal thickness固定弦齿厚constant chord端面弦齿厚transverse chordal tooth thickness弦上齿厚tooth thickness on the chord弧齿厚circular thickness外圆弧齿厚external circular tooth thickness分度圆圆弧上弧齿厚circular tooth thickness on the arc of a reference circle 端面基圆齿厚transverse base thickness法向基圆齿厚normal base thickness二十一. 宽（width）齿宽face width有效齿宽effective facewidth端面齿槽宽transverse space width法向齿槽宽normal space width涡轮齿宽worm wheel facewidth蜗杆齿宽worm facewidth二十二. (交) 点瞬时接触点point of contact轴线交点crossing point of axes二十三. 弧总作用弧total arc of transmission端面作用弧transverse arc of transmission 纵向作用弧overlap arc二十四. 轴瞬时轴instantaneous axis二十五. 半径(radius) & diameter(原始轮廓)过渡曲线弯曲半径radius of curvature of transition curve (original profile) 刀具半径cutter radius刀刃圆角半径cutter edge radius齿轮刀具名义直径gear cutter nominal diameter有效分度圆直径effective reference diameter二十六.长度（length）公法线长度base tangent length二十七.高度（深度）工作高度working depth齿顶高addendum齿根高dedendum弦齿高chordal height固定弦齿高constant chord height全齿高whole depth齿高tooth height到弦的测量高度measuring height up to the chard二十八. 其他修缘tip relief修根root relief齿向修正axial modification齿端修补end relief鼓形修正crowning鼓形齿crowned teeth挖根undercut导程lead最小齿顶高修正min addendum modification凸台boss紧固件fastener加强肋rib垫儿pad凹槽recess 切洞cutout 夹具JIG。

齿轮基本术语中英文对照

齿轮基本术语中英文对照NUMER OF TEETH 齿数DIAMETRIAL PITCH 径节PRESSURE ANGLE (NORM.) 压力角HELIX ANGLE 螺旋角LEAD 导程PITCH DIA. (STAND ＆MESHING) 节圆?BASE DIAMETER 基圆直径?OUTSIDE DIAMETER 齿顶圆直径?ROOT DIAMETER 齿根圆直径?WHOLE DEPTH 全齿高?CIRCULAR PITCH (NORM) 周节?CHORDAL THICKNESS 弦齿高CHORDAL ADDENDUM 弦齿厚WIRE SIZEMIC OVER WIRESLEAD CHK IN. @ 90°BLOCK MEASURE 3 TEETH 跨3齿公法线长度? CENTER DISTANCE 中心距BACKLASH 齿隙NUMBER OF TEETH IN MATE 配对齿轮齿数AGMA QUALITY (MIN.) 精度等级花键参数及部分翻译FLAT ROOT SIDE FITNUMBER OF TEETH 齿数SPINE PITCH 花键径节PRESSURE ANGLE 压力角BASE DIAMETER 基圆直径PITCH DIAMETER 节圆直径MAJOR DIAMETER 大径FORM DIAMETER 成型圆直径MINOR DIAMETER 小径CIRCULAR SPACE WIDTH 弧形齿槽宽度MAX. ACTUAL ?最大实际应用齿宽MIN. LEFECTIVE ?最小有效齿宽MEASUREMENT BETWEEN PINS 量棒距离PIN DIAMETER 量棒直径WIRE SIZE 量棒直径MIC OVER WIRES 跨棒距LEAD CHK IN. @ 90°隔90°检查螺旋线偏差FLAT ROOT SIDE FIT 平齿根齿侧定心LEAD 齿向WIRE SIZE 量棒直径MIC OVER WIRES 跨棒间距BACKLASH 齿侧间隙PITCH DIA. (STAND ＆MESHING)分度圆直径CIRCULAR PITCH (NORM) 基节FORM DIAMETER 展成圆直径MAX. ACTUAL 最大实际齿厚MIN. LEFECTIVE 最小作用齿厚MEASUREMENT BETWEEN PINS 跨棒距（就是M值）PITCH DIA. (STAND ＆MESHING)分度圆直径CIRCULAR PITCH (NORM) 基节FORM DIAMETER 展成圆直径MAX. ACTUAL 最大实际齿厚MIN. LEFECTIVE 最小作用齿厚MEASUREMENT BETWEEN PINS 跨棒距（就是M值）齿轮Toothed gear；Gear齿轮副Gear pair平行轴齿轮副Gear pair with parallel axes相交轴齿轮副Gear pair with intersecting axes齿轮系Train of gears行星齿轮系Planetary gear train齿轮传动Gear drive；Gear transmission配对齿轮Mating gears小齿轮Pinion大齿轮Wheel；Gear主动齿轮Driving gear从动齿轮Driven gear行星齿轮Planet gear行星架Planet carrier太阳轮Sun gear内齿圈Ring gear；Annulus gear外齿轮External gear内齿轮Internal gear中心距Centre distance轴交角Shaft angle连心线Line of centres减速齿轮副Speed reducing gear pair增速齿轮副Speed increasing gear pair齿数比Gear ratio传动比Transmission ratio轴平面Axial plane基准平面Datum plane节平面Pitch plane端平面Transverse plane法平面Normal plane分度曲面Reference surface节曲面Pitch surface齿顶曲面Tip surface齿根曲面Root surface基本齿廓Basic tooth profile基本齿条Basic rack产形齿条Counterpart rack产形齿轮Generating gear of a gear产形齿面Generating flank基准线Datum line轮齿Gear teeth；Tooth齿槽Tooth space右旋齿Right-hand teeth左旋齿Left-hand teeth变位齿轮Gears with addendum modification；X-gears高度变位圆柱齿轮副X-gear pair with reference centre distance 角度变位圆柱齿轮副X-gear pair with modified centre distance 高度变位锥齿轮副X-gear pair without shaft angle modification 角度变位圆柱齿轮副X-gear pair with shaft angle modification 变位系数Modification coefficient变位量Addendum modification径向变位系数Addendum modification coefficient中心距变位系数Centre distance modification coefficient圆柱齿轮Cylindrical gear顶圆Tip circle根圆Root circle齿距Pitch齿距角Angular pitch公法线长度Base tangent length分度圆直径Reference diameter节圆直径Pitch diameter基圆直径Base diameter顶圆直径Tip diameter根圆直径Root diameter齿根圆角半径Fillet radius齿高Tooth depth工作高度Working depth齿顶高Addendum齿根高Dedendum弦齿高Chordal height固定弦齿高Constant chord height齿宽Facewidth有效齿宽Effective facewidth端面齿厚Transverse tooth thickness法向齿厚Normal tooth thickness端面基圆齿厚Transverse base thickness法向基圆齿厚Normal base thickness端面弦齿厚Transverse chordal tooth thickness固定弦齿厚Constant chord端面齿顶厚Crest width法向齿顶厚Normal crest width端面齿槽宽Transverse spacewidth法向齿槽宽Normal spacewidth齿厚半角Tooth thickness half angle槽宽半角Spacewidth half angle压力角Pressure angle齿形角Nominal pressure angle圆弧圆柱蜗杆Arc-contact worm；hollow flank worm；ZC-worm直廓环面蜗杆Enveloping worm with straight line grneratrix；TA worm平面蜗杆Planar worm wheel；P-worm wheel平面包络环面蜗杆Planar double enveloping worm；TP-worm平面二次包络蜗杆Planar double-enveloping worm wheel；TP-worm wheel锥面包络环面蜗杆Toroid enveloping worm wheel；TK-worm wheel渐开线包络环面蜗杆Toroid enveloping worm hich involute holicoid generatrix；TI-wo rm锥蜗杆Spiroid锥蜗轮Spiroid gear锥蜗杆副Spiroid gear pair中平面Mid-plane长幅内摆线Prolate hypocycloid短幅内摆线Curtate hypocycloid渐开线Involute；Involute to a circle延伸渐开线Prolate involute缩短渐开线Curtate involute球面渐开线Spherical involute渐开螺旋面Involute helicoid阿基米德螺旋面Screw helicoid球面渐开螺旋面Spherical involute helicoid圆环面Toroid圆环面的母圈Generant of the toroit圆环面的中性圈Middle circle of the toroid圆环面的中间平面Middle-plane of the toroid圆环面的内圈Inner circle of the toroid啮合干涉Meshing interference切齿干涉Cutter interference齿廓修型Profile modification；Profile correction修缘Tip relief修根Root relief齿向修形Axial modification；Longitudinal correction齿端修薄End relief鼓形修整Crowning鼓形齿Crowned teeth挖根Undercut瞬时轴Instantaneous axis瞬时接触点Point of contact瞬时接触线Line of contact端面啮合线Transverse path of contact啮合曲面Surface of action啮合平面Plane of action啮合区域Zone of action总作用弧Total arc of transmission端面作用弧Transverse arc of transmission 纵向作用弧Overlap arc总作用角Total angle of transmission端面作用角Transverse angle of transmission 纵向作用角Overlap angle总重合度Total contact ratio端面重合度Transverse ratio纵向重合度Overlap ratio标准齿轮Standard gears非变位齿轮X-gero gear标准中心距Referencr centre distance名义中心距Nominal centre distance分度圆柱面Reference cylinder节圆柱面Pitch cylinder基圆柱面Basic cylinder齿顶圆柱面Tip cylinder齿根圆柱面Root cylinder节点Pitch point节线Pitch line分度圆Reference circle节圆Pitch circle基圆Basic circle定位面Locating face外锥距Outer cone distance内锥距Inner cone distance中点锥距Mean cone distance背锥距Back cone distance安装距Locating distance轮冠距Tip distance；crown to back冠顶距Apex to crown偏置距Offset齿线偏移量Offset of tooth trace分锥角Reference cone angle节锥角Pitch cone angle顶锥角Tip angle根锥角Root angle背锥角Back cone angle齿顶角Addendum angel齿根角Dedendum angle任意点压力角Pressure angle at a point任意点螺旋角Spiral angle at a point中点螺旋角Mean spiral angle大端螺旋角Outer spiral angle小端螺旋角Inner spiral angle蜗杆Worm蜗轮Worm wheel蜗杆副Worm gear pair圆柱蜗杆Cylindrical worm圆柱蜗杆副Cylindrical worm pair环面蜗杆Enveloping worm环面蜗杆副Enveloping worm pair阿基米德蜗杆Straight sided axial worm；ZA-worm 渐开线蜗杆Involute helicoid worm；ZI-worm法向直廓蜗杆Straight sided normal worm；ZN-worm 锥面包络圆柱蜗杆Milled helicoid worm；ZK-worm椭圆齿轮Elliptical gear非圆齿轮副Non-circular gear pair圆柱针轮副Cylindsical lantern pinion and wheel针轮Cylindsical tan tein gear ；pin-wheel谐波齿轮副Harmoric gear drive波发生器Wave generator柔性齿轮Flexspine刚性齿轮Circular spline非圆齿轮Non-circular gear分度圆环面Reference tosoid。

齿轮术语中英文对照

齿轮术语中英文对照Toothed gear；；齿轮Gear齿轮副Gear pair Gear pair with平行轴齿轮副parallel axes Gear pair with相交轴齿轮副intersecting axes齿轮系Train of gears Planetary gear行星齿轮系train Gear drive；Gear ；齿轮传动transmission配对齿轮Mating gears相啮齿面Mating flank阿基米德螺旋面Screw helicoid Spherical involute小齿轮Pinion共轭齿面Conjugate flank球面渐开螺旋面helicoid大齿轮主动齿轮Wheel；Gear ；Driving gear可用齿面有效齿面Usable flank Active flank圆环面圆环面的母圈Toroid Generant of the toroit Middle circle of the 从动齿轮Driven gear上齿面Addendum flank圆环面的中性圈toroid Middle-plane of the行星齿轮Planet gear下齿面Dedendum flank圆环面的中间平面toroid行星架太阳轮Planet carrier Sun gear Ring gear；；内齿圈Annulus gear Profile modification；；外齿轮External gear齿廓Tooth profile齿廓修型Profile correction内齿轮中心距Internal gear Centre distance端面齿廓法向齿廓Transverse profile Normal profile修缘修根Tip relief Root relief Axial modification；；轴交角Shaft angle轴向齿廓Axial profile齿向修形Longitudinal correction Back cone tooth连心线Line of centres背锥齿廓profile Speed reducing减速齿轮副gear pair Speed increasing增速齿轮副gear pair齿数比Gear ratio Transmission传动比ratio轴平面Axial plane法向模数Normal module瞬时接触点Point of contact端面模数Transverse module瞬时轴Instantaneous axis模数Module挖根Undercut齿棱Tip；Tooth tip ；鼓形齿Crowned teeth齿线Tooth trace鼓形修整Crowning齿端修薄End relief槽底Bottom land切齿干涉Cutter interference齿根过渡曲面齿顶Fillet Crest；Top land ；圆环面的内圈啮合干涉Inner circle of the toroid Meshing interference 非工作齿面Non-working flank渐开螺旋面Involute helicoid工作齿面Working flank球面渐开线Spherical involute异侧齿面Opposite flank缩短渐开线Curtate involute同侧齿面Corresponding flank延伸渐开线Prolate involute左侧齿面Left flank渐开线Involute to a circle右侧齿面Right flank短幅内摆线Curtate hypocycloid Involute；；齿面Tooth flank长幅内摆线Prolate hypocycloid基准平面Datum plane轴向模数Axial module瞬时接触线Line of contact Transverse path of节平面Pitch plane径节Diametral pitch端面啮合线contact端平面Transverse plane齿数Number of teech Virtual number of啮合曲面Surface of action法平面Normal plane当量齿数teeth Number of starts；；啮合平面Plane of action分度曲面Reference surface头数Number of threads啮合区域Zone of action节曲面Pitch surface螺旋线Helix；Circular helix ；总作用弧Total arc of transmission Transverse arc of齿顶曲面Tip surface圆锥螺旋线Conical spiral端面作用弧transmission Helix angle；；齿根曲面Root surface螺旋角Spiral angle Total angle of基本齿廓基本齿廓Basic tooth profile导程Lead总作用角transmission Transverse angle of基本齿条Basic rack导程角Lead angle端面作用角transmission产形齿条Counterpart rack Generating gear产形齿轮of a gear产形齿面基准线轮齿齿槽Generating flank Datum line Gear teeth；Tooth ；Tooth space长幅外摆线短幅外摆线摆线长幅摆线Prolate epoicycloid Curtate epoicycloid Cycloid Prolate cycloid端面重合度纵向重合度标准齿轮非变位齿轮Transverse ratio Overlap ratio Standard gears X-gero gear Referencr centre右旋齿Right-hand teeth短幅摆线Curtate cycloid标准中心距distance左旋齿Left-hand teeth Gears with addendum变位齿轮modification；；X-gears X-gear pair with高度变位圆柱齿轮reference centre副distance X-gear pair with角度变位圆柱齿轮modified centre副distance X-gear pair without shaft高度变位锥齿轮副angle modification角度变位圆柱齿轮X-gear pair with人字齿轮Double-helical gear齿根圆柱面Root cylinder斜齿条Helical rack齿顶圆柱面Tip cylinder直齿条Spur rack基圆柱面Basic cylinder斜齿轮Single-helical gear Helical gear；；节圆柱面Pitch cylinder直齿轮Spur gear分度圆柱面Reference cylinder内摆线Hypocycloid名义中心距Nominal centre distance外摆线Epicycloid总重合度Total contact ratio阿基米德螺旋线Archimedes spiral纵向作用角Overlap angle纵向作用弧Overlap arc副shaft angle modification Modification Involute cylindrical渐开线齿轮coefficient Addendum gear节点Pitch point变位系数变位量modification Addendum摆线齿轮Cycloidal gear节线Pitch line Circular-arc gear；；径向变位系数modification coefficient Centre distance Double-circular-arc中心距变位系数modification coefficient圆柱齿轮Cylindrical gear假想曲面Imaginary surfance Normal pressure顶圆Tip circle任意点法向压力角angle at a point Transverse pressure根圆Root circle任意点端面压力角angle at a point Working pressure齿距Pitch啮合角angle齿距角Angular pitch Base tangent公法线长度length Reference分度圆直径diameter Tip distance；crown to ；节圆直径Pitch diameter径向侧隙Radial blacklash轮冠距back基圆直径顶圆直径根圆直径齿根圆角半径齿高工作高度齿顶高Base diameter Tip diameter Root diameter Fillet radius Tooth depth Working depth Addendum锥齿轮锥齿轮副准双曲面齿轮副准双曲面齿轮冠轮端面齿轮直齿锥齿轮Bevel gear Bevel gear pair Hypoid gear pair Hypoid gear Crown gear Contrate gear Straight bevel gear Skew bevel gear；；齿根高Dedendum斜齿锥齿轮Helical bevel gear Curved tooth bevel弦齿高Chordal height曲面齿锥齿轮gear Constant chord固定弦齿高height Enicycloid bevel齿宽Facewidth摆线齿锥齿轮gear有效齿宽Effective零度齿锥齿轮Zerot bevel gear任意点螺旋角Spiral angle at a point任意点压力角Pressure angle at a point弧齿锥齿轮Spiral bevel gear齿根角Dedendum angle齿顶角Addendum angel背锥角Back cone angle冠顶距偏置距齿线偏移量分锥角节锥角顶锥角根锥角Apex to crown Offset Offset of tooth trace Reference cone angle Pitch cone angle Tip angle Root angle法向侧隙Normal blacklash安装距Locating distance圆周侧隙blacklash顶隙Bottom clearance Circumferential背锥距Back cone distance中点锥距Mean cone distance内锥距Inner cone distance外锥距Outer cone distance定位面Locating face基圆Basic circle双圆弧齿轮gear节圆Pitch circle圆弧齿轮W-N gear分度圆Reference circle facewidth Transverse tooth端面齿厚thickness Normal tooth法向齿厚thickness Transverse base端面基圆齿厚thickness Spiral bevel gear Normal base法向基圆齿厚thickness profile Transverse端面弦齿厚chordal tooth thickness固定弦齿厚端面齿顶厚Constant chord Crest width Normal crest法向齿顶厚width Transverse端面齿槽宽spacewidth Normal法向齿槽宽spacewidth Tooth thickness齿厚半角half angle Spacewidth half槽宽半角angle Crossing point of压力角Pressure angle轴线交点axes Nominal pressure齿形角angle Arc-contact worm；hollow ；圆弧圆柱蜗杆flank worm；；ZC-worm Enveloping worm with straight line直廓环面蜗杆grneratrix；TA ；worm Planar worm Cylindsical lantern平面蜗杆wheel；P-worm ；wheel Planar double平面包络环面蜗杆enveloping worm；；喉圆Gorge circle 针轮gear ；pin-wheel Cylindsical tan tein喉平面Gorge plane圆柱针轮副pinion and wheel咽喉面Gorge非圆齿轮副非圆齿轮副Non-circular gear pair齿根圆环面Root tosoid椭圆齿轮Elliptical gear公共锥顶Common apex锥面包络圆柱蜗杆ZK-worm法向直廓蜗杆worm；ZN-worm ；Milled helicoid worm；；分锥顶点Reference cone apex渐开线蜗杆ZI-worm Straight sided normal中锥面Middle cone阿基米德蜗杆worm；ZA-worm ；Involute helicoid worm；；Straight sided axial 前锥面Front cone环面蜗杆副Enveloping worm pair背锥面Back cone环面蜗杆Enveloping worm齿根圆锥面Root cone圆柱蜗杆副Cylindrical worm pair节圆锥面齿顶圆锥面Pitch cone Face cone；tip cone ；蜗杆副圆柱蜗杆Worm gear pair Cylindrical worm分度圆锥面Reference cone蜗轮Worm wheel圆柱齿弧锥齿轮with circle arc tooth蜗杆Worm 8 字啮合锥齿轮Octoid gear小端螺旋角Inner spiral angle锥齿轮的当量圆柱齿轮gear of bevel gear Virtual cylindrical大端螺旋角Outer spiral angle圆柱齿轮端面齿轮副Contrate gear pair中点螺旋角Mean spiral angle TP-worm Planar double-enveloping平面二次包络蜗杆worm wheel；；TP-worm wheel Toroid enveloping锥面包络环面蜗杆worm wheel；；TK-worm wheel Toroid enveloping worm hich 渐开线包络环面蜗involute holicoid杆generatrix；；TI-worm Worm wheel锥蜗杆Spiroid蜗轮齿宽facewidth锥蜗轮锥蜗杆副中平面Spiroid gear Spiroid gear pair Mid-plane直径系数咽喉半径齿宽角Diametral quotient Gorge radius Width angle非圆齿轮分度圆环面Non-circular gear Reference tosoid刚性齿轮Circular spline蜗杆齿宽Worm facewidth柔性齿轮Flexspine螺纹Thread波发生器Wave generator分度圆蜗旋线Reference helix谐波齿轮副Harmoric gear drive。

中英文齿轮基本术语

齿轮基本术语（中英文对照)齿轮 Toothed gear；Gear齿轮副 Gear pair平行轴齿轮副 Gear pair with parallel axes 相交轴齿轮副 Gear pair with intersecting axes齿轮系 Train of gears行星齿轮系 Planetary gear train 齿轮传动 Gear drive；Gear transmission配对齿轮 Mating gears小齿轮 Pinion大齿轮 Wheel；Gear主动齿轮 Driving gear从动齿轮 Driven gear行星齿轮 Planet gear行星架 Planet carrier太阳轮 Sun gear内齿圈 Ring gear；Annulus gear外齿轮 External gear内齿轮 Internal gear中心距 Centre distance轴交角 Shaft angle连心线 Line of centres减速齿轮副 Speed reducing gear pair增速齿轮副 Speed increasing gear pair齿数比 Gear ratio传动比 Transmission ratio轴平面 Axial plane基准平面 Datum plane节平面 Pitch plane端平面 Transverse plane法平面 Normal plane分度曲面 Reference surface节曲面 Pitch surface齿顶曲面 Tip surface齿根曲面 Root surface基本齿廓 Basic tooth profile基本齿条 Basic rack产形齿条 Counterpart rack产形齿轮 Generating gear of a gear产形齿面 Generating flank基准线 Datum line轮齿 Gear teeth；Tooth齿槽 Tooth space右旋齿 Right-hand teeth左旋齿 Left-hand teeth变位齿轮 Gears with addendum modification;X-gears高度变位圆柱齿轮副 X-gear pair with reference centre distance 角度变位圆柱齿轮副 X—gear pair with modified centre distance 高度变位锥齿轮副 X-gear pair without shaft angle modification 角度变位圆柱齿轮副 X-gear pair with shaft angle modification变位系数 Modification coefficient变位量 Addendum modification径向变位系数 Addendum modification coefficient 中心距变位系数 Centre distance modification coefficient圆柱齿轮 Cylindrical gear顶圆 Tip circle根圆 Root circle齿距 Pitch齿距角 Angular pitch公法线长度 Base tangent length分度圆直径 Reference diameter节圆直径 Pitch diameter基圆直径 Base diameter顶圆直径 Tip diameter根圆直径 Root diameter齿根圆角半径 Fillet radius齿高 Tooth depth工作高度 Working depth齿顶高 Addendum齿根高 Dedendum弦齿高 Chordal height固定弦齿高 Constant chord height齿宽 Facewidth有效齿宽 Effective facewidth端面齿厚 Transverse tooth thickness法向齿厚 Normal tooth thickness端面基圆齿厚 Transverse base thickness法向基圆齿厚 Normal base thickness端面弦齿厚 Transverse chordal tooth thickness固定弦齿厚 Constant chord端面齿顶厚 Crest width法向齿顶厚 Normal crest width端面齿槽宽 Transverse spacewidth法向齿槽宽 Normal spacewidth齿厚半角 Tooth thickness half angle槽宽半角 Spacewidth half angle压力角 Pressure angle齿形角 Nominal pressure angle圆弧圆柱蜗杆 Arc—contact worm；hollow flank worm；ZC-worm 直廓环面蜗杆 Enveloping worm with straight line grneratrix；TA worm平面蜗杆 Planar worm wheel；P—worm wheel平面包络环面蜗杆 Planar double enveloping worm;TP-worm 平面二次包络蜗杆 Planar double-enveloping worm wheel；TP-worm wheel 锥面包络环面蜗杆 Toroid enveloping worm wheel；TK-worm wheel渐开线包络环面蜗杆 Toroid enveloping worm hich involute holicoid generatrix；TI-worm锥蜗杆 Spiroid锥蜗轮 Spiroid gear锥蜗杆副 Spiroid gear pair中平面 Mid—plane齿面 Tooth flank右侧齿面 Right flank左侧齿面 Left flank同侧齿面 Corresponding flank异侧齿面 Opposite flank工作齿面 Working flank非工作齿面 Non-working flank相啮齿面 Mating flank共轭齿面 Conjugate flank可用齿面 Usable flank有效齿面 Active flank上齿面 Addendum flank下齿面 Dedendum flank齿根过渡曲面 Fillet齿顶 Crest;Top land槽底 Bottom land齿廓 Tooth profile端面齿廓 Transverse profile法向齿廓 Normal profile轴向齿廓 Axial profile背锥齿廓 Back cone tooth profile齿线 Tooth trace齿棱 Tip;Tooth tip模数 Module端面模数 Transverse module法向模数 Normal module轴向模数 Axial module径节 Diametral pitch齿数 Number of teech当量齿数 Virtual number of teeth头数 Number of starts;Number of threads螺旋线 Helix；Circular helix圆锥螺旋线 Conical spiral螺旋角 Helix angle；Spiral angle导程 Lead导程角 Lead angle阿基米德螺旋线 Archimedes spiral外摆线 Epicycloid长幅外摆线 Prolate epoicycloid短幅外摆线 Curtate epoicycloid摆线 Cycloid长幅摆线 Prolate cycloid短幅摆线 Curtate cycloid内摆线 Hypocycloid直齿轮 Spur gear斜齿轮 Helical gear；Single-helical gear直齿条 Spur rack斜齿条 Helical rack人字齿轮 Double-helical gear渐开线齿轮 Involute cylindrical gear摆线齿轮 Cycloidal gear圆弧齿轮 Circular-arc gear；W—N gear双圆弧齿轮 Double-circular-arc gear假想曲面 Imaginary surfance任意点法向压力角 Normal pressure angle at a point 任意点端面压力角 Transverse pressure angle at a point 啮合角 Working pressure angle顶隙 Bottom clearance圆周侧隙 Circumferential blacklash法向侧隙 Normal blacklash径向侧隙 Radial blacklash锥齿轮 Bevel gear锥齿轮副 Bevel gear pair准双曲面齿轮副 Hypoid gear pair准双曲面齿轮 Hypoid gear冠轮 Crown gear端面齿轮 Contrate gear直齿锥齿轮 Straight bevel gear斜齿锥齿轮 Skew bevel gear；Helical bevel gear曲面齿锥齿轮 Curved tooth bevel gear弧齿锥齿轮 Spiral bevel gear摆线齿锥齿轮 Enicycloid bevel gear零度齿锥齿轮 Zerot bevel gear圆柱齿轮端面齿轮副 Contrate gear pair锥齿轮的当量圆柱齿轮 Virtual cylindrical gear of bevel gear8字啮合锥齿轮 Octoid gear圆柱齿弧锥齿轮 Spiral bevel gear with circle arc tooth profile分度圆锥面 Reference cone节圆锥面 Pitch cone齿顶圆锥面 Face cone；tip cone齿根圆锥面 Root cone背锥面 Back cone前锥面 Front cone中锥面 Middle cone分锥顶点 Reference cone apex轴线交点 Crossing point of axes公共锥顶 Common apex齿根圆环面 Root tosoid咽喉面 Gorge喉平面 Gorge plane喉圆 Gorge circle分度圆蜗旋线 Reference helix螺纹 Thread蜗杆齿宽 Worm facewidth蜗轮齿宽 Worm wheel facewidth直径系数 Diametral quotient咽喉半径 Gorge radius齿宽角 Width angle长幅内摆线 Prolate hypocycloid短幅内摆线 Curtate hypocycloid渐开线 Involute；Involute to a circle延伸渐开线 Prolate involute缩短渐开线 Curtate involute球面渐开线 Spherical involute渐开螺旋面 Involute helicoid阿基米德螺旋面 Screw helicoid球面渐开螺旋面 Spherical involute helicoid圆环面 Toroid圆环面的母圈 Generant of the toroit圆环面的中性圈 Middle circle of the toroid圆环面的中间平面 Middle—plane of the toroid圆环面的内圈 Inner circle of the toroid啮合干涉 Meshing interference切齿干涉 Cutter interference齿廓修型 Profile modification；Profile correction修缘 Tip relief修根 Root relief齿向修形 Axial modification;Longitudinal correction齿端修薄 End relief鼓形修整 Crowning鼓形齿 Crowned teeth挖根 Undercut瞬时轴 Instantaneous axis瞬时接触点 Point of contact瞬时接触线 Line of contact端面啮合线 Transverse path of contact啮合曲面 Surface of action啮合平面 Plane of action啮合区域 Zone of action总作用弧 Total arc of transmission端面作用弧 Transverse arc of transmission纵向作用弧 Overlap arc总作用角 Total angle of transmission端面作用角 Transverse angle of transmission 纵向作用角 Overlap angle总重合度 Total contact ratio端面重合度 Transverse ratio纵向重合度 Overlap ratio标准齿轮 Standard gears非变位齿轮 X-gero gear标准中心距 Referencr centre distance名义中心距 Nominal centre distance 分度圆柱面 Reference cylinder节圆柱面 Pitch cylinder基圆柱面 Basic cylinder齿顶圆柱面 Tip cylinder齿根圆柱面 Root cylinder节点 Pitch point节线 Pitch line分度圆 Reference circle节圆 Pitch circle基圆 Basic circle定位面 Locating face外锥距 Outer cone distance内锥距 Inner cone distance中点锥距 Mean cone distance背锥距 Back cone distance安装距 Locating distance轮冠距 Tip distance；crown to back冠顶距 Apex to crown偏置距 Offset齿线偏移量 Offset of tooth trace分锥角 Reference cone angle节锥角 Pitch cone angle顶锥角 Tip angle根锥角 Root angle背锥角 Back cone angle齿顶角 Addendum angel齿根角 Dedendum angle任意点压力角 Pressure angle at a point任意点螺旋角 Spiral angle at a point中点螺旋角 Mean spiral angle大端螺旋角 Outer spiral angle小端螺旋角 Inner spiral angle蜗杆 Worm蜗轮 Worm wheel蜗杆副 Worm gear pair圆柱蜗杆 Cylindrical worm圆柱蜗杆副 Cylindrical worm pair环面蜗杆 Enveloping worm环面蜗杆副 Enveloping worm pair阿基米德蜗杆 Straight sided axial worm；ZA—worm 渐开线蜗杆 Involute helicoid worm;ZI—worm法向直廓蜗杆 Straight sided normal worm；ZN-worm 锥面包络圆柱蜗杆 Milled helicoid worm；ZK-worm椭圆齿轮 Elliptical gear非圆齿轮副 Non—circular gear pair 圆柱针轮副 Cylindsical lantern pinion and wheel 针轮 Cylindsical tan tein gear ；pin—wheel谐波齿轮副 Harmoric gear drive波发生器 Wave generator柔性齿轮 Flexspine刚性齿轮 Circular spline非圆齿轮 Non—circular gear分度圆环面 Reference tosoid模具成形不良用语英汉对照aberration 色差 bite 咬入blacking hole 涂料孔(铸疵） blacking scab 涂料疤blister 起泡 blooming 起霜blow hole 破孔 blushing 泛白body wrinkle 侧壁皱纹 breaking-in 冒口带肉bubble 膜泡 burn mark 糊斑burr 毛边 camber 翘曲cell 气泡 center buckle 表面中部波皱check 细裂痕 checking 龟裂chipping 修整表面缺陷 clamp—off 铸件凹痕collapse 塌陷 color mottle 色斑corrosion 腐蚀 crack 裂痕crazing 碎裂 crazing 龟裂deformation 变形 edge 切边碎片edge crack 裂边 fading 退色filler speak 填充料斑 fissure 裂纹flange wrinkle 凸缘起皱 flaw 刮伤flow mark 流痕 galling 毛边glazing 光滑 gloss 光泽grease pits 污斑 grinding defect 磨痕haircrack 发裂 haze 雾度incrustation 水锈 indentation 压痕internal porosity 内部气孔 mismatch 偏模mottle 斑点 necking 缩颈nick 割痕 orange peel 橘皮状表面缺陷overflow 溢流 peeling 剥离pit 坑 pitting corrosion 点状腐蚀plate mark 模板印痕 pock 麻点pock mark 痘斑 resin streak 树脂流纹resin wear 树脂脱落 riding 凹陷sagging 松垂 saponification 皂化scar 疤痕 scrap 废料scrap jam 废料阻塞 scratch 刮伤/划痕scuffing 深冲表面划伤 seam 裂痕shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔 sink mark 凹痕skin inclusion 表皮折叠 straightening 矫直streak 条状痕 surface check 表面裂痕surface roughening 橘皮状表皮皱折 surging 波动sweat out 冒汗 torsion 扭曲warpage 翘曲 waviness 波痕webbing 熔塌 weld mark 焊痕whitening 白化 wrinkle 皱纹实验与试验用语air permeability test 透气性试验 austenitic steel 沃斯田铁钢brinell hardness 布耐内尔硬度 brinell hardness test 布氏硬度试验charpy impact test 夏比冲击试验 conical cup test 圆锥杯突试验cup flow test 杯模式流动度试验 dart drop impact test 落锤冲击试验Elmendorf test 埃罗门多撕裂强度试验 environmental stress cracking test环境应力龟裂试验ericessen test 埃留伸薄板拉伸试验 falling ball impact test 落球冲击试验fatigue test 疲劳试验 ferrite 纯铁体gantt chart 甘特图 heat cycle test 热循环试验histogram 柱状图 hot bend test 热弯试验izod impact test 埃左德冲击试验 loop tenacity 环结强度martens heat distortion temperature test 马顿斯耐热试验martensite 马氏体 mullen bursting strength tester 密廉式破裂强度试验机nol ring test 诺尔环试验 normal distribution 常态分配ozone resistance test 抗臭氧试验 pareto diagram 柏拉图peeling test 剥离试验 pinhole test 针孔试验机rattler test 磨耗试验rockweel hardness test 洛氏硬度试验rockweel hardness 洛氏威尔硬度 rolinx process 罗林克斯射出压缩成形法rossi-peakes flow test 罗西皮克斯流动试验 sampling inspection 抽样检查scratch hardness 抗刮硬度 shore hardness 萧氏硬度spiral flow test 螺旋流动试验 surface abrasion test 表面磨耗试验taber abraser 泰伯磨耗试验机 tensile impact test 拉伸冲击试验tensile strength 抗拉强度 tension test 张力试验thermal shock test 冷热剧变试验 torsion test 扭曲试验ubbelohde viscometer 乌别洛德黏度计 vicat indentation test 维卡针压陷试验Vickers hardness test 维氏硬度试验 warpage test 翘曲试验weatherometer 人工老化试验机 weissenberg effect 威森伯格回转效应锻铸造关连用语accretion 炉瘤 acid converter 酸性转炉acid lining cupola 酸性熔铁炉 acid open—hearth furnace 酸性平炉aerator 松砂机 air set mold 常温自硬铸模airless blasting cleaning 离心喷光 all core molding 集合式铸模all round die holder 通用模座 assembly mark 铸造合模记号back pouring 补浇注 backing sand 背砂base bullion 粗金属锭 base permeability 原砂透气度belling 压凸 billet 坏料bleed 漏铸 blocker 预锻模膛blocking 粗胚锻件 blow hole 铸件气孔board drop hammer 板落锤 bottom pour mold 底浇bottom pouring 底注 boxless mold 脱箱砂模break—off core 缩颈砂心 brick molding 砌箱造模法buckle 剥砂面 camber 错箱camlachie cramp 铸包 cast blade 铸造叶片casting flange 铸造凸缘 casting on flat 水平铸造chamotte sand 烧磨砂 charging hopper 加料漏斗cleaning of casting 铸件清理 closed—die forging 合模锻造core compound 砂心黏结剂 core template 砂心模板core vent 砂蕊排气孔 corner gate 压边浇口counter blow hammer 对击锻造 counter lock 止口镶嵌方式depression 外缩凹孔 die approach 模口角度draw out 锻造拔长 draw plate 起模板draw spike 起模长针 dummying 预锻embedded core 加装砂心 erosion 冲砂fettling 铸件清理 filling core 埋入砂心~filling in 填砂 film play 液面花纹finishing slag 炼后熔渣 flash gutter 锻模飞边槽flask molding 砂箱造模 forging roll 辊锻机formboard 进模口板 gutter 锻模飞边槽hammer man 锻工 heading machine 顶镦机impacter 卧式锻造机 inblock cast 整体铸造ingot 铸锭 ingot blank 铸坯inlay casting 镶铸法 investment casting 失模铸造isothermal forging 恒温锻造 loose piece 木模活块molding pit 铸模地坑 pouring process 浇注法recasting 重铸 roll forging 轧锻rolled surface 轧制表面 rough sand 粗砂roughing forge 粗锻 sand crushing 塌箱seamless forging 无缝锻造 separate 分离shave 崩砂 shrinkage fit 收缩配合shut height 闭合高度 sieve mesh 筛孔sintering of sand 铸砂烧贴 slag 熔渣slag inclusion 夹渣 stickness 黏模性strip layout 带状胚料排样法 tap casting 顶注top gate 顶注浇口 unworked casting 不加工铸件upender 翻转装置 upending 顶锻uphill casting 底铸 white cast iron 白口铸件品质、生产名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类：FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最后一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告。

齿轮术语英语词汇

齿轮及齿轮加工设备的相关词汇A.abrasive tooth wear 齿面研磨磨损absolute tangential velocity 绝对切向速度 accelerometer 加速表addendum 齿顶高addendum angle 齿顶角addendum circle 齿顶圆addendum surface 上齿面adhesive wear 粘着磨损adjustability 可调性adjustability coefficients 可调系数 adjusting wedge 圆盘端铣刀的可调型楔块 allowable stress 允许应力alternate blade cutter 双面刀盘angular backlash 角侧隙angular bevel gears 斜交锥齿轮angular displacement 角移位angular pitch 齿端距angular testing machine 可调角度试验机 approach action 啮入arbor 心轴arbor distance 心轴距arc of approach 啮入弧arc of recess 啮出弧attraction 收紧average cutter diameter 平均刀尖直径axial displacement 轴向位移axial factor 轴向系数axial locating surface 轴向定位面axial pitch 轴向齿距axial plane 轴向平面axial rakeangle 轴向前角axial thrust 轴向推力axle testing machine 传动桥试验机B.back angle 背锥角Back angle distance 背角距（在背锥母线方向） Back cone 背锥Back cone distance 背锥距Back cone element 背锥母线Backlash 侧隙Backlash tolerance 侧隙公差Backlash variation 侧隙变量Backlash variation tolerance 侧隙变量公差第 1 页Bandwidth 频带宽Base circle 基圆Base diameter 基圆直径Base pitch 基节Base radius 基圆半径Base spiral angle 基圆螺旋角Basic rack 基本齿条Bearing 轴承Bearing preload 轴承预负荷Bearing spacing／spread 轴承间距 Bending fatigue 弯曲疲劳Bending stress 弯曲应力Bevel gears 锥齿轮Bias 对角接触Bias in 内对角接触Bias out 外对角接触Blade angle 刀齿齿廓角Blade edge radius 刀尖圆角半径Blade letter 刀尖凸角代号Blade life 刀尖寿命Blade point width 刀顶宽Blank offset 毛坯偏置距Bland position 毛坯位置Bottom land 齿槽底面Boundary lubrication 界面润滑 Breakage 破裂Bridged contact pattern 桥型接触斑点 Broach 拉刀Burnishing 挤齿C．Case crushing 齿面塌陷CBN 立方氮化硼chamfer 倒角chordal addendum 弦齿高chordal thickness 弦齿厚chuck 卡盘circular broach 圆拉刀circular face-mill 圆盘端面铣刀 circular peripheral-mill 圆盘铣刀 circular pitch 周节circular thickness 弧齿厚circular thickness factor 弧齿厚系数 clearance 顶隙clearance angle 后角coarse pitch 大节距第 2 页coast side 不工作齿侧combination 组合combined preload 综合预负荷complementary crown gears 互补冠状齿轮completing cycle 全工序循环composite action 双面啮合综合检验误差compressive stress 压应力concave side 凹面concentricity 同心度concentricity tester 同心度检查仪cone distance 锥距cone element 锥面母线conformal surfaces 共型表面coniskoid 斜锥齿轮conjugate gears 共轭齿轮conjugate racks 共轭齿条contact fatigue 接触疲劳contact norma 接触点法线contact pattern (tooth contact pattern) 轮齿接触斑点 contact ratio 重合度contact stress 接触应力continuous index 连续分度control gear 标准齿轮，检验用齿轮convex side 凸面coolant 冷却液corrosive wear 腐蚀性磨损corrugated tool 阶梯刨刀counter forma surfaces 反法向表面cradle 摇台cradle test roll 摇台角cross 大小端接触crossing point 交错点crown 齿冠crown circle 锥齿轮冠圆crowned teeth 鼓形齿crown gear 冠轮crown to back （轮冠距）轮冠至安装定位面距离crown to crossing point 轮冠至相错点距离cutter 刀盘cutter axial 刀盘的轴向位置cutter axial plane 刀盘轴向平面cutter axis 刀盘轴线cutter diameter 刀盘直径cutter edge radius 刀刃圆角半径第 3 页cutter head 刀盘体cutter number 刀号cutter parallel 刀盘平垫片cutter point diameter 刀尖直径cutter point radius 刀尖半径cutter point width 刀顶距cutter spindle 刀盘主轴cutter spindle rotation angle 刀盘主轴转角cutting distance 切齿安装距C.V. testing mashing 常速试验机cyclex 格里森粗铣精拉法圆盘端铣刀cylindrical gears 圆柱齿轮D.Datum tooth 基准齿Debur 去毛刺Decibel (CB) （噪音）分贝Decimal ratio 挂轮比值Dedendum 齿根高Dendendum angle 齿根角Dedendum surface 下齿面Deflection 挠曲Deflection test 挠曲试验Deflection testing machine 挠曲试验机Depthwise taper 齿高收缩Design data sheet 设计数据表Destructive pitting 破坏性点蚀Destructive wear 破坏性磨损Developed setting 试切调整Dial indicator 度盘式指示表Diametral pitch 径节Diamond 菱形接触Dinging ball check 钢球敲击检查Disc-mill cuter 盘铣刀Dish angle 凹角Displacement 位移Displacement error 位移误差Double index 双分度Double roll 双向滚动Down roll 向下滚动Drive side 工作齿侧Duplete 双刃刀Duplex 双重双面法Duplex helical 双重螺旋法（加工方法之一）Duplex spread blade 双重双面刀齿（加工／磨齿方法） Duplex taper 双重收缩齿第 4 页Durability factor 耐久系数Dynamic factor 动载荷系数E Ease-off 修正、失配Eccentric 偏心Eccentric angle 偏心角Eccentricity 偏心度Edge radius 刀尖圆角半径Effective bearing spacing 轴承有效间距Effective face width 有效宽度（有效齿宽）Elastic coefficient 弹性系数Elastic deformation 弹性变形Elastic limit 弹性极限Elastohydrodynamic lubrication 弹性液压润滑Element 母线、要素End movement 轴向移动Endrem 修内端凸轮、导程凸轮Endurance life 耐久寿命Endurance limit 耐久极限Engine torque 发动机扭矩Enveloping 包络EP lubricant, EP 极压润滑剂EPG check, “EPG” 检查Equal addendum teeth 等齿顶高齿Equicurv 等高齿大轮成形法Equidep 等高齿Equiside 等边Equivalent fear ratio 当量传动比Equivalent number of teeth 当量齿数Equivalent pitch radius 当量节圆半径Equivalent rack 当量齿条Expander 涨胎Expanding arbor 可张心轴Extreme pressure lubricant 极压润滑剂F Face acvance 斜齿轮扭曲量Face angle 顶锥角（面锥角）Face angle distance 顶锥角距Face apex 顶锥顶Face apex beyond crossing point 顶锥顶至相错点距离 Face cone 顶锥Face cone element 齿顶圆锥母线，面锥母线Face contact ratio 齿长重合度，轴向重合度（圆柱齿轮） Face line 齿面与轴面交线Face width 齿宽Factor of safety 安全系数第 5 页Fatigue breakage 疲劳破裂Fatigue failure 疲劳失效Fatigue test 疲劳测试Feed cam 进给凸轮Feed gears 进给齿轮Fillet 齿根圆角Fillet curve 齿根过渡曲线Fillet radius 齿根圆角半径Film strength 液膜强度Filter (electronic) （电子的）滤波器Filter (mechanical) （机械的）滤波器Fine pitch （小模数）细径节Finisher 精切机床Fishtail 鱼尾形Fixed setting 固定安装法Flank 下齿面Flanking 下齿面加工Formarc 加工齿轮用的曲线齿廓刀具Formate 成形法Former 齿廓样板，靠模Forming 成型，在磨具内挤压成型Form tool 成形刀Fourier analysis 傅里叶分析Frequency 频率Friction load 摩擦负荷Front angle 前角Front cone 前锥Front crown 前锥齿冠Front crown to crossing point 前锥齿冠至交错点 Full-depth teeth 全齿高齿Fundametal 基频G Gable 山形齿沟底面Gear 齿轮Gear axial displacement 齿轮轴向位移Gear axial plane 齿轮轴向平面Gear axis 齿轮轴线Gear center 齿轮中心Gear combination 齿轮组合Gear cone 大轮锥距Geared index 齿轮系分度Gear finisher 成形法齿轮精切机床Gear manufacturing summary 齿轮加工调整卡 Gear marking compound 检查齿轮啮合涂色剂Gear member 大轮第 6 页Gear planer 成型刨齿机Gear ratio 齿数比Gear rougher 齿轮粗切机床Gears 齿轮组Gear tipping 齿轮倾斜Generated gear 展成法齿轮Generating cam 展成凸轮Generating gear 展成齿轮Generating pressure angle 产形轮压力角Generating train 展成传动键Generation 展成Generator 展成齿轮加工机床Geneva index 星形轮分度，槽轮分度Geometry factor-durability 齿面接触强度几何系数 Geometry factor0-strength 强度几何系数G-flow 格里森制金属件的商标，采用冷挤压成形法G-form 采用热锻成形法制造GLE-sine 砂轮内外压力角正弦波进行修整用机构G-plete 全工序法Gradeability 托曳力Grinding cracks 磨削裂纹G-spin 精密主轴的机床G-trac 圆柱齿轮的无端链式机床的商标H．Hand of cutter 刀盘方向Hand of spiral 螺旋方向Hand-rolling tester 手动滚动试验机Hardac 镶篇淬硬刀体精切刀盘Hard finishing 硬齿面精加工Hardness ratio factor 硬度比系数Harmonic 谐振Harmonic search 谐振追踪Harmonic sweep 谐振扫描Heel 轮齿大端Heel pattern 大端接触Helical duplex 双重螺旋法Helical motion 螺旋运动Helixact 螺旋运动法Helixform 螺旋成形法Hertz (Hz) 赫兹Hook angle 断面前角Horizontal displacement 水平位移Horizontal offset 水平偏置HRH 高减速比准双曲面齿轮（大于10：1的减速比）Hunting tooth combination 大小齿轮齿数无公因数的齿轮副第 7 页Hudrodynamic lubrication 液压润滑Hupermesh 超配合Hypoid gears 准双曲面齿轮Hypoid offset 准双曲面齿轮偏置距I.Imaginary generating gear 假想成形法 Incremental index 逐齿分度Index gears 分度齿轮Index interval 分度跳跃齿齿数Index plate 分度盘Index tolerance 分度公差Index variation 分度变化量Indicator anchorage 指示表支撑座Inertia factor 惯量系数Initial pitting 初期点蚀Inner addendum 小端齿顶高Inner cone distance 小端锥距Inner dedendum 小端齿根高Inner slot width 小端槽宽Inner spiral angle 小端螺旋角Inserted blade cutter 镶片刀盘Inside blade 内切刀齿Inside point diameter 内切刀尖直径 Instantaneous contact pattern 瞬时接触斑点 Interference 干涉Interference point 干涉点Interlocking disc-mill cutters 交错齿盘形铣刀 Intermittent index 间断分度Internal bevel gear 内锥齿轮Inverse gear ratio 反齿数比Involute 渐开线Involute gear 渐开线齿轮Involute interference point 渐开线干涉点 Involute spiral angle 渐开线螺旋角Involute teeth 渐开线齿J.Jet lubrication 喷射润滑me 顶根接触Lapping 研磨Lead cam 导程凸轮Length of action 啮合长度Lengthwise bridge 纵向桥型接触Lengthwise mismatch 纵向失配Lengthwise sliding velocity 纵向滑动速度Life factor 寿命系数Lift 垂直位移第 8 页Limit point width 极限刀顶距Limit pressure angle 极限压力角Linear displacement transducer 线性位移传感器 Line of action 啮合线Line of centers 中心线Line of contact 接触线Load sharing ratio 负荷分配比Localized tooth contact 齿局部接触Locating surface 定位表面Long-and-short-addendum teeth 高变位齿轮Long-toe-short-heel 小端长，大端短接触 Lubricant 润滑剂Lubrication 润滑Lubricity 润滑性M.Machine center 基床中心点Machine center to back 机床中心至工件安装基准面 Machine plane 机床切削平面Machine root angle 毛坯安装角Marking compound 检查齿轮啮合型情况使用的涂色剂 Master blade 标准刀齿Master gear 标准齿轮Mean addendum 中点齿顶高Mean cone distance 中点锥距Mean dedendum 中点齿根高Mean diametral pitch 中点径节Mean measuring addendum 中点测量齿顶高Mean measuring depth 中点测量齿高Mean measuring thickness 中点测量厚度Mean normal base pitch 中点法向基节Mean normal diameter pitch 中点法向径节Mean normal module 中点法向模数Mean point 中点，平均点Mean radius 中点半径Mean section 中点截面Mean slot width 中点齿槽宽Mean spiral angle 中点螺旋角Measuring addendum 测量齿顶高Measuring tooth thickness 测量齿厚Member 齿轮，元件Mesh point 啮合点Minimum slot width 最小槽宽Mismatch 失配Miter gears 等齿数整角锥齿轮副Mixed lubrication 混合润滑第 9 页Modified contact ratio 修正总重合度Modified roll 滚修正比Module 模数Motion curves 运动曲线Motor torque 电机扭矩Mounting distance 安装距Mounting surface 安装面N.Narrow-tow-wide-heel 小端窄大端宽接触No load 空载Nominal 名义Non-generated gear 非展成大轮Normal 法向，法线，法面Normal backlash 法向侧隙Normal backlash tolerance 法向侧隙公差 Normal base pitch 法向基节Normal chordal addendum 法向弦齿高Normal chordal thickness 法向弦齿厚Normal circular pitch 法向周节Normal circular thickness 法向弧齿厚Normal contact ratio 法向重合度Normal diametral pitch 法向径节Normal direction 法线方向Normal (perpendicular) load 法向（垂直）负载 Normal module 法向模数Normal plane 法向平面Normal pressure angle 法向压力角Normal section 法向截面Normal space-width taper 正常齿槽宽收缩 Normal thickness taper 正常齿厚收缩Normal tilt 法向刀倾Normal wear 正常磨损No-roll roughing 无滚动粗切Number of teeth 齿数O．Octoid teeth 锥齿轮的“8”字啮合Offset 偏置距Operating load 工作负荷Operating pressure angle 工作压力角 Operating torque 工作扭矩Outer addendum 大端齿顶高Outer cone distance 外锥距Outer dedendum 大端齿根高Outer slot width 大端槽宽Outer spiral angle 大端螺旋角Outside blade 外切刃点第 10 页Outside diameter 外径，大端直径Outside point diameter 外切刀尖直径Outside radius 齿顶圆半径Outside surface 外表面Overhung mounting 双支承安装Overload breakage 超负荷破裂Overload factor 超负荷系数P.Path of action 啮合点轨迹Path of contact 接触迹Peak load 峰值负荷Peak torque 峰值扭矩Pedestal bearings 安装差速器壳的架座轴承 Performance torque 性能扭矩Perim-mate 研磨锥齿轮和准双面齿轮用的全齿面研磨法 Pinion 小轮Pinion axial displacement 小轮轴向位移Pinion cone 小轮锥距Pinion front bearing 小轮前端轴承Pinion head bearing 小轮后端前轴承Pinion rear bearing 小轮后端后轴承Pinion rougher 小轮粗切机Pinion offset 小轮偏置距Pitch 节距，齿距Pitch angle 节锥角Pitch apex 节锥顶Pitch apex beyond crossing point 节锥顶超出至相错点 Pitch apex to back 节锥顶至安装端面Pitch apex to crown 节锥顶至轮冠Pitch circle 节圆Pitch cone 节锥Pitch curve 节面曲线Pitch diameter 节径Pitch element 节面母线Pitch line 节线Pitch-line chuck 节圆夹具Pitch-line runout 节线跳动Pitch plane 节面Pitch point 节点Pitch radius 节圆半径Pitch surfaces 节曲面Pitch tolerance 齿距公差Pitch trace 节线Pitch variation 齿距变化量Pitting 点蚀第 11 页Plane of action 啮合平面Plane of rotation 旋转平面Planning generator 展成法刨齿机Plastic deformation 塑性变形Plastic flow 塑性流动Plate index 分度盘Point diameter 刀尖直径Point of contact 接触点Point radius 刀尖半径Point width 刀顶距Point width taper 刀顶距收缩Pressure lubrication 压力润滑Prime mover torque 原动机扭矩Profile angle 齿廓角Profile bridge 齿廓桥形接触Profile contact ratio 齿廓重合度Profile mismatch 齿廓啮合失配Profile radius of curvature 齿廓曲率半径 Proof surface 检测基准面Q．Quality measurement system 质量检测系统 Quenching cracks 淬火裂纹Quenching die 淬火压模Quenching press 淬火压床R．Rack 齿条Radial 径向刀位Radial load 径向负荷Radial locating surface 径向定位表面 Radial rake angle 径向前角Ratio control roughing 变滚比粗切Ratio gears 滚比挂轮Ratio of roll 滚比Ratio of roll gears 滚比挂轮Recess action 啮出Relative displacement 相对位移Relative movement 相对运动Relative radius of curvature 相对曲率半径 Residual stress 残余应力Revacycle 直齿锥齿轮圆拉法用机床及刀具 Revex 直齿锥齿轮粗拉法Ridg-AC 镶片圆盘端面粗铣刀Ridging 沟条变形Ring gear 大轮，环形齿轮Rippling 振纹Roll centering 滚动定心第 12 页Roll queching 滚动式淬火压床Roll gears 摆角挂轮Rolling 滚轧Rolling velocity 滚动速度Root angle 根锥角Root angle tilt 齿根角倾斜Root apex 根锥顶Root apex beyond crossing point 根锥顶至相错点的距离 Root apex to back 根锥顶至安装基准面距离Root circle 齿根圆Root cone 根锥Root diameter 根圆直径Root line 齿根线Root radius 根圆半径Root surface 齿根曲面Roughac 弧齿锥齿轮粗切刀Rougher 粗切机RSR 弧齿锥齿轮条形刀齿铣刀盘Runout 径向跳动Runout tolerance 径向跳动公差S.Scoring 胶合Scoring index 胶合指数Scuffing 胶合Sector 扇形齿／齿弧Segment 扇形齿／体Segmental-blade cutter 大轮精切刀Separation 分离间隙Separating factor 分离系数Separating force 分离力Set-in 补充切入，进刀Set-over 补充转角，调整转换Shaft angle 轴转角Shot peening 喷丸强化Sidebank 边频Side movement 侧向位移Side rake angle 侧前角Single cycle 单循环法Single roll 单滚动Single setting 单面调整法Single side 单面精切法Single-side taper 齿槽收缩Size factor 尺寸系数Skew bevel gears 斜直齿锥齿轮Skip index 跳齿分度第 13 页Slide-roll ratio 单位滑滚比，比滑Sliding base 床鞍，滑座Sliding base setting 床鞍调整，滑座调整Sliding velocity 滑动速度Slip-chip 直齿锥齿轮一次成形刀Slip torque 滑移扭矩Slotting tool 切槽刀Slot width 槽宽Slot-width taper 槽宽收缩Small cutter development 小刀盘试切，能产生接近渐开线的刀具 Solid cutter 整体刀盘Sound test 噪声试验Space-width taper 齿距收缩Spacing tolerance 齿距公差Spacing variation 齿距变动量Spalling 剥落Specific sliding 单位滑动比Speed gears 速度挂轮Spherical involute teeth 球面渐开线齿Spherica limacon teeth 球面钳线齿Spindle rotation angle 主轴旋转角Spiral angle 螺旋角Spiral bevel gears 弧齿锥齿轮Splash lubrication 飞溅润滑Split profile 齿型中断Spread blade 双面刀Spread blade 双面刀渐缩Standard depthwise taper 标准深锥度Standard taper 正常收缩Standard thickness 正常齿厚收缩Stock allowance 毛坯加工流量Straddle cutter 双列刀齿刀盘Straddle mounting 跨装Straight bevel gears 直齿锥齿轮Strength factor 强度系数Stress concentration factor 应力集中系数Stub teeth 短齿Subsurface initiated fatigue breakage 金属表面斜层初始疲劳破裂 Summary of machine settings 机床调整卡Sump lubrication 油槽润滑Sum velocity 总速度Surface asperities 表面粗糙度Surface condition factor 表面条件系数Surface deformation 表面变形第 14 页Surface durability 表面耐久度Surface fatigue 表面疲劳Surface initiated fatigue breakage 表面初始疲劳破裂 Surface of action 啮合面Surface of revolution 回转面Surface treatment 表面处理Swinging base 回转底座Swing pinion cone 摆动小轮节锥法Swivel 刀转Swivel angle 刀转角Symmetrical rack 对称齿条Symmetrical rack proportions 对称齿条比例T.Tangential load 切向负荷Tangent plane 切平面Tanline 小轮夹具Tanruf 双联粗切刀，8.5模数一下Tan-tru 用在加工1016－2540mm的锥齿刀具Taper roughing 具有刀顶距收缩的大小轮粗切过程 Temperature factor 温度系数Testing machine 试验机Thickness taper 齿厚收缩Tilt 刀倾Tilt angle 刀倾角Tilted rootline taper 倾斜齿根收缩Tip radius 齿顶圆角半径Toe 轮齿小端Toe pattern 小端接触Tool 刀具Tool advance 刀具进刀Tool edge radius 刀刃圆角半径Tool point width 刀顶距Tooth angle 齿角Tooth bearing 齿支撑面，轮齿接触面Tooth contact analysis 轮齿接触分析Tooth contact pattern 轮齿接触斑点Tooth horizontal 齿水平面Tooth layout 轮齿剖面图Tooth-mesh frequency 齿啮合频率Tooth number 齿数Tooth profile 齿形，齿廓Tooth spacing testing 齿距检查仪Tooth spiral 齿螺旋线Tooth surface 轮齿表面Tooth taper 轮齿收缩第 15 页Tooth-to-tooth composite tolerance 一齿度量中心距公差 Tooth-to- Tooth composite variation 一齿度量中心距变量 Tooth trace 齿线Tooth vertical 齿垂直面Top 齿顶Topland 齿顶面Topland width 齿顶面宽度Topping 修顶Top relief angle 顶刃后角Toprem 修根刀片Toprem angle 刀齿突角角度Top slope angle 刀齿顶刃倾角Total composite tolerance 总综合公差Total composite variation 总度量中心距变动量Total contact ratio 总重合度Total index tolerance 总分度公差Total index variation 总分度变动量Tractive effort torque 牵引力扭矩Transverse circular pitch 端面周节Transverse circular thickness 端面弧齿厚Transverse contact ratio 端面重合度Transverse diametral pitch 端面径节Transverse module 端面模数Transverse plane 端平面Transverse pressure angle 端面压力角Transverse space-width taper 端面槽宽收缩Transverse thickness taper 端面齿厚收缩Tredgold’s approximation 背锥近似法Tribology 润滑与磨损学Triplex 三面刃圆盘端铣刀Two-tool generator 双刀展成加工机床U.Undercut 根切Undeveloped settings 试切前调整Uniform roll 匀速滚动Uniform velocity tester 匀速试验机Uni-spand 大轮心轴Unit load 单位负荷Unitool 曲面镶片刀Up-roll 向上滚动V. V and H check 锥齿轮啮合的VH检查Variable roll 变滚动Velocity factor 速度系数Versacut 弧齿锥齿轮加工多用刀盘Vers-grip 卡紧小齿轮用的卡盘（商标名称）第 16 页Vertical direction 垂直方向Vertical displacement 垂直位移Vertical factor 垂直系数Vertical force 垂直力Vertical offset 垂直偏置距Vertical plane 垂直面Virtual number of teeth 当量齿数Virtual pitch radius 当量节圆半径Viscosity 粘度V-tool V型刀具W. Waveform 波形Wear 磨损Webless-type gear 无幅板式齿轮Web-type gear 幅板式齿轮Wheel slip torque 车轮打滑扭矩Whole depth 齿全高Workhead 工件头座Workhead offset 垂直轮位Workholding equipment 工件夹具Working depth 工作齿高Working stress 工作允许应力Work tests roll 检验工件主轴转角X. X-pandisk 大轮蝶形，涨胎心轴Z. Zero depthwise taper 等齿高Zerol 零度锥齿轮1.number of teeth 齿数;2.dlametral pitch [normal] 径节;3.base circle diameter[reference] 基园直径;4.normal pressure angle法向压力角;5.transverse pressure angle 端面压力角;6.reference circle diameter分园直径;7.addendum齿顶高;8.full tooth depih 全齿高;9.mates at dimensioned centres(可能是:配对齿轮)10.backlash at above centres侧隙(可能是最大中心距对应的)11.tip diameter齿顶园12.hand of helix 旋向13.helix angle螺旋角14.contact diameter接触点直径15.start of active profile有效齿廓开始点16.maximum total composite error最大综合误差(有两种:切向和径向,第 17 页原文说得不清楚)17.maximum tooth to tooth composite error 最大单齿综合误差(同上)18.total tolerance 总误差19.maximum tooth spacing error at rer最大齿间宽误差(参考园)20.circle diameter bstween an tw 单词写法可能有错21.adjacent teeth同上22.transverse tooth thicknsss[max.min]端面齿厚23.on reference circle diameter分园直径24.span gauge dimension cher 3teeth公法线长或跨棒距25 max/min or dimension over stancaro26 rollers where span saugs camnct27 be used 使用的/被使用的/用过的原文英语写得不正规,有很多拼写错误! 翻译供参考!第 18 页。

齿轮之种类与名称翻译

齿轮之种类与名称翻译 Addendum angle 齿顶角(伞齿轮)Angle gear 斜交轴伞齿轮Angle of approach 渐近角(齿轮)Angle of recess 渐远角(齿轮)Annular gear 内齿轮Backgear 背轮；后齿轮Bevel gear 伞齿轮；锥齿轮Bevel pinion 锥齿轮Bevel planet gear 行星锥齿轮Change gear 交换齿轮；变速齿轮 Corrected gear 校正齿轮Cycloidal gear 摆线齿轮Differential gear 差动齿轮 Differential planet gear 差动行星齿轮Double helical gear 人字齿轮 Drive pinion 传动小齿轮 Driven gear 被动齿轮；从动齿轮 Driving gear 传动齿轮；主动齿轮 Epicyclic gear 行星齿轮Face gear 平面齿轮Gear 齿轮；传动装置Gear box 齿轮箱Gear coupling 齿轮联轴节Gear drive 齿轮传动Gear mesh 齿轮齿合Gear rack 齿轮齿条Gear ratio 齿轮比Gear sector 扇形齿轮Gear sprial 螺旋齿轮Gear wheel 齿轮Gear wheel shaft 齿轮轴Gearing 齿轮装置；传动装置Gear-type coupling 齿轮联轴器Helical bevel gear 螺旋伞齿轮；斜齿伞齿轮 Helical spur gear 螺旋直齿圆柱齿轮 Helical worm gear 斜齿轮蜗轮Helicl gear 斜齿轮；螺旋齿轮 Herringbone gear 人字齿轮Integrating gear 积分齿轮Intermediate gear 中速齿轮；二档齿轮 Involute curfe 渐开线齿轮Knuckle gear 圆齿齿轮Low speed gear 低速齿轮Master gear 主齿轮Miter gear 等径伞齿轮Modified involute gear 渐开线修正齿轮 Overdrive gear 增速齿轮；超速转动齿轮Pick-off gear 可互换齿轮Pinion 小齿轮；副齿轮Pinion shaft 齿轮轴Planetary 行星的；行星齿轮的Planetary pinion 行星小齿轮Planetray reducer 行星减速齿轮Rack and pinion gearing 齿条；齿轮传动装置 Reverse gear 反向齿轮Ring gear 环形齿轮Screw gear 螺旋齿轮Sector gear 扇形齿轮Sector shaft 扇形齿轮轴Servo gear 伺服齿轮Shutter gear box 快门齿轮箱Skew bevel gear 斜伞齿轮Skew gear 斜齿轮Skew wheel 斜齿轮Skew-axes gear 斜轴齿轮Speed gear 变速齿轮Spiral bevel gear 螺旋伞齿轮；弧齿锥齿轮 Spiral gear 螺旋齿轮；斜齿轮Split gear 拼合齿轮Spur bevel gear 正齿伞齿轮Spur gear 正齿轮Spur pinion 正小齿轮Spur wheel 正齿轮Straight-teeth bevel gear 直齿伞齿轮 Straight-teeth gear 直齿轮Toothed gearing 齿轮装置Tumbler gear 摆动换向齿轮；三星齿轮 Variable gear 变速齿轮Variable-speed gear 变速齿轮Wheel tooth 齿轮齿Worm gear 蜗轮Worm gearing 蜗杆传动装置Wheelwork 转动装置。

齿轮术语中英文对照表

齿轮术语中英文对照表阿基米德蜗杆Archimedes worm安全系数safety factor；factor of safety安全载荷safe load变形deformation摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile背锥角back angle背锥距back cone distance比例尺scale变速speed change变速齿轮change gear ；change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面粗糙度surface roughness不完全齿轮机构intermittent gearing补偿compensation参数化设计parameterization design，PD 残余应力residual stress操纵及控制装置operation control device槽数Geneva numerate侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism 差速器differential常用机构conventional mechanism; mechanism in common use承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch 齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter；pinion-shaped shaper cutter齿轮滚刀hob ，hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack—shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio传动比transmission ratio，speed ratio传动装置gearing；transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft创新设计creation design垂直载荷、法向载荷normal load从动带轮driven pulley从动件driven link，follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打滑slipping带传动belt driving单列轴承single row bearing单位矢量unit vector当量齿轮equivalent spur gear; virtual gear 当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导程lead导程角lead angle等效质量equivalent mass（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal顶隙bottom clearance定轴轮系ordinary gear train；gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge惰轮idle gear额定寿命rating life额定载荷load rating发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch 法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反正切Arctan范成法generating cutting仿形法form cutting非标准齿轮nonstandard gear非接触式密封non—contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line；standard pitch line 分度圆reference circle; standard (cutting）pitch circle分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone 封闭差动轮系planetary differential复合应力combined stress复式螺旋机构Compound screw mechanism 干涉interference刚度系数stiffness coefficient钢丝软轴wire soft shaft根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam惯性力矩moment of inertia ,shaking moment惯性力平衡balance of shaking force冠轮crown gear轨迹生成path generation轨迹发生器path generator滚刀hob过度切割undercutting耗油量oil consumption耗油量系数oil consumption factor横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动率sliding ratio环面蜗杆toroid helicoids worm缓冲装置shocks; shock—absorber机械machinery机械平衡balance of machinery机械设计machine design; mechanical design 机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design，CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone极限位置extreme （or limiting) position极位夹角crank angle between extreme （or limiting）positions计算机辅助设计computer aided design，CAD 计算机辅助制造computer aided manufacturing，CAM计算机集成制造系统computer integrated manufacturing system, CIMS计算力矩factored moment；calculation moment计算弯矩calculated bending moment间隙backlash减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross—belt drive交错轴斜齿轮crossed helical gears胶合scoring角速度angular velocity角速比angular velocity ratio结构structure结构设计structural design截面section节点pitch point节距circular pitch；pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load 径向基本额定动载荷basic dynamic radial load rating径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load绝对运动absolute motion绝对速度absolute velocity可靠性reliability可靠性设计reliability design, RD理论廓线pitch curve理论啮合线theoretical line of action力矩moment力平衡equilibrium力偶couple力偶矩moment of couple轮坯blank螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line模块化设计modular design, MD模数module磨损abrasion ；wear；scratching耐磨性wear resistance内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring啮合engagement，mesh, gearing啮合点contact points啮合角working pressure angle 啮合线line of action啮合线长度length of line of action盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric切齿深度depth of cut曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved—shoe follower曲线运动curvilinear motion全齿高whole depth权重集weight sets球面副spheric pair球面渐开线spherical involute球面运动spherical motion人字齿轮herringbone gear润滑装置lubrication device润滑lubrication三角形花键serration spline三角形螺纹V thread screw少齿差行星传动planetary drive with small teeth difference升程rise升距lift实际廓线cam profile输出轴output shaft实际啮合线actual line of action双曲面齿轮hyperboloid gear顺时针clockwise瞬心instantaneous center死点dead point太阳轮sun gear特性characteristics图册、图谱atlas图解法graphical method退火anneal陀螺仪gyroscope外力external force外形尺寸boundary dimension网上设计on-net design, OND微动螺旋机构differential screw mechanism 位移displacement蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism蜗杆旋向hands of worm蜗轮worm gear无级变速装置stepless speed changes devices相对速度relative velocity相对运动relative motion相对间隙relative gap象限quadrant橡皮泥plasticine小齿轮pinion小径minor diameter谐波齿轮harmonic gear谐波传动harmonic driving斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance—to return-time ratio 行星齿轮装置planetary transmission行星轮planet gear行星轮变速装置planetary speed changing devices行星轮系planetary gear train旋转运动rotary motion压力角pressure angle应力图stress diagram应力—应变图stress—strain diagram优化设计optimal design油杯oil bottle有效圆周力effective circle force 圆带传动round belt drive圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱蜗杆cylindrical worm圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle运动副kinematic pair运动粘度kenematic viscosity载荷load展成法generating直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm质量mass中心距center distance中心距变动center distance change中径mean diameter终止啮合点final contact，end of contact 周节pitch轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile转动副revolute (turning）pair转速swiveling speed ; rotating speed转轴revolving shaft转子rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley；bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear自由度degree of freedom，mobility总重合度total contact ratio总反力resultant force总效率combined efficiency；overall efficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting最少齿数minimum teeth number最小向径minimum radius作用力applied force坐标系coordinate frame。

齿轮术语的英文翻译

EXTERNAL SPUR GEAR DATA（外圆柱齿轮参数）manufacturing data（制造参数）part number（零件号）tooth form（齿面）gear type（齿轮类型）number of teeth（齿数）normal module（法向模数）normal pressure angle (at ref circle)法向压力角（在分度圆上）helix angle (at ref circle)螺旋角（在分度圆上）helical lead（螺旋导程）hand of helix（旋向）reference face width（参考齿宽）outside diameter（齿顶圆直径）chamfer diameter（倒圆直径）reference(pitch)circle diameter（分度圆直径）或节圆start of active profile diameter有效渐开线起始圆直径form diameter 展成直径root diameter齿根圆直径base circle diameter基圆直径whole depth全齿高normal circular tooth thickness (at reference circle)法向弧齿厚（在分度圆上）root type齿根形式root fillet radius 齿根圆角半径lead crown齿向鼓形HOB DATA滚刀参数pressure angle压力角tooth thickness at reference line分圆齿厚protuberance凸角tip radius齿顶圆半径reference part number 零件号INSPECTION DATA检验数据profile tolerance and modifications齿形公差和修形profile hollow齿形中凹refernce pitch circle runout节圆跳动pitch variation齿距偏差lead variation齿向偏差lead hollow齿向中凹profile surface finish渐开线齿面精加工ball diameter量球直径dimension over two balls in same plane跨棒距REFERENCE DATA-MATING GEAR对啮齿的参考参数normal center distance 中心距mating gear part number对啮齿轮零件号mumber of teeth on mating gear对啮轮齿数backlash (nominal CD ,ROOM TEMP)侧隙(法线方向，室温)general notes(通用技术要求)1.DO not scale drawing(不要在图上量取尺寸)2.all surfaces corners and edges must be free from burrsand sharp edges-break 0.075 MM MAX(所有面,角和边不能有毛刺,锐边倒钝不超过0.075mm)3.unless otherwise stated(除非特别注明,否则)A.all dimensions and tolerance are in millimeters perchinese standard(所有以毫米为单位的尺寸和公差均按中国标准)B.all surface finishes to be 3.2 micrometer or better(所有表面粗糙度不应低于3.2)C.all dimension are finished dimensions;no allowance has beenmade for any change in maximum or least material conditiondue to heat treatment(所有尺寸均为最终尺寸;热处理导致的最大或最小实体条件的变化不应超出允差)D linear dimensions to be +/- 0.25 MM(线性尺寸偏差为+/- 0.25 MM)E angular dimensions to be +/- 0.5º(角度尺寸偏差为+/- 0.5º)4.mark part number as shown(如图作零件号)5.mark serial number as shown(如图作系列号)6.heat treatment to be applied to all surfaces(整体热处理)gear notes(齿轮技术要求)1.do not grind roots and fillets after heat treatment(热处理后不得磨及齿根和圆角)2.no steps or grooves permissible in root and fillet region afterhoning or grinding(珩磨后,齿根和圆角区域不允许有台阶或凹痕)3.profile tolerance based upon floating band fit(齿形误差应以公差带为计)4.gear must be free from grind burns and tempering(齿面不得烧伤)5.pitch line runout and other tooth tolerances are with respect todatum A(节圆跳动和其它齿轮公差均以基准A为测量基准)6.profile tolerance to be measured between form and chamfer(齿形误差应由渐开线起始(或终止)圆测量至齿顶倒角)7.min hardness must be achieved in tooth root and fillet region(齿根和圆角处的硬度不得低于硬度下差)8.root radius tangent to profile not to extend above form diameter(齿根圆角要与齿面相切,而且不能超过渐开线起始(或终止)圆直径。

齿轮术语中英文对照表

齿轮术语中英文对照表阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load变形deformation摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile背锥角back angle背锥距back cone distance比例尺scale变速speed change变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面粗糙度surface roughness不完全齿轮机构intermittent gearing补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽数Geneva numerate侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft创新设计creation design垂直载荷、法向载荷normal load从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打滑slipping带传动belt driving单列轴承single row bearing单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth 当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导程lead导程角lead angle等效质量equivalent mass（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge惰轮idle gear额定寿命rating life额定载荷load rating发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反正切Arctan范成法generating cutting仿形法form cutting非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone封闭差动轮系planetary differential复合应力combined stress复式螺旋机构Compound screw mechanism干涉interference刚度系数stiffness coefficient钢丝软轴wire soft shaft根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam惯性力矩moment of inertia ,shaking moment惯性力平衡balance of shaking force冠轮crown gear轨迹生成path generation轨迹发生器path generator滚刀hob过度切割undercutting耗油量oil consumption耗油量系数oil consumption factor横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动率sliding ratio环面蜗杆toroid helicoids worm缓冲装置shocks; shock-absorber机械machinery机械平衡balance of machinery机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械无级变速mechanical stepless speed changes 基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment间隙backlash减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角速度angular velocity角速比angular velocity ratio结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load绝对运动absolute motion绝对速度absolute velocity可靠性reliability可靠性设计reliability design, RD理论廓线pitch curve理论啮合线theoretical line of action力矩moment力平衡equilibrium力偶couple力偶矩moment of couple轮坯blank螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line模块化设计modular design, MD模数module磨损abrasion ;wear; scratching耐磨性wear resistance内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric切齿深度depth of cut曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线运动curvilinear motion全齿高whole depth权重集weight sets球面副spheric pair球面渐开线spherical involute球面运动spherical motion人字齿轮herringbone gear润滑装置lubrication device润滑lubrication三角形花键serration spline三角形螺纹V thread screw少齿差行星传动planetary drive with small teeth difference 升程rise升距lift实际廓线cam profile输出轴output shaft实际啮合线actual line of action双曲面齿轮hyperboloid gear顺时针clockwise瞬心instantaneous center死点dead point太阳轮sun gear特性characteristics图册、图谱atlas图解法graphical method退火anneal陀螺仪gyroscope外力external force外形尺寸boundary dimension网上设计on-net design, OND微动螺旋机构differential screw mechanism位移displacement蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism蜗杆旋向hands of worm蜗轮worm gear无级变速装置stepless speed changes devices相对速度relative velocity相对运动relative motion相对间隙relative gap象限quadrant橡皮泥plasticine小齿轮pinion小径minor diameter谐波齿轮harmonic gear谐波传动harmonic driving斜齿轮的当量直齿轮equivalent spur gear of the helical gear 心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio行星齿轮装置planetary transmission行星轮planet gear行星轮变速装置planetary speed changing devices行星轮系planetary gear train旋转运动rotary motion压力角pressure angle应力图stress diagram应力—应变图stress-strain diagram 优化设计optimal design油杯oil bottle有效圆周力effective circle force圆带传动round belt drive圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing 圆柱副cylindric pair圆柱蜗杆cylindrical worm圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle运动副kinematic pair运动粘度kenematic viscosity载荷load展成法generating直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm质量mass中心距center distance中心距变动center distance change中径mean diameter终止啮合点final contact, end of contact 周节pitch轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile转动副revolute (turning) pair转速swiveling speed ; rotating speed转轴revolving shaft转子rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear 锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force总效率combined efficiency; overall efficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting最少齿数minimum teeth number最小向径minimum radius作用力applied force坐标系coordinate frame。

螺旋伞齿轮的基本参数

螺旋伞齿轮的基本参数螺旋伞齿轮是一种常见的齿轮类型，具有螺旋状齿形，主要用于传递力和运动。

其基本参数包括以下几个方面：模数（Module）：模数是螺旋伞齿轮齿轮的基本尺寸参数，表示齿轮齿廓的大小。

模数是齿轮直径和齿数的比值，通常以毫米为单位。

齿数（Number of Teeth）：齿数表示螺旋伞齿轮上的齿的数量。

齿数的选择与传递功率、速比等因素有关。

螺旋角度（Helix Angle）：螺旋伞齿轮的齿是呈螺旋状排列的，螺旋角度表示齿轮齿的螺旋线相对于轴线的夹角。

通常以度数表示。

法向模数（Normal Module）：法向模数是齿轮齿廓的模数，与齿轮轴线垂直方向的模数。

螺旋方向（Helix Direction）：螺旋伞齿轮的齿廓是螺旋状的，螺旋方向表示齿廓的螺旋是顺时针还是逆时针。

压力角（Pressure Angle）：压力角是齿轮齿廓和轴线的夹角，是齿轮设计中的重要参数之一。

通常以度数表示。

螺旋距离（Helix Distance）：螺旋距离是螺旋伞齿轮齿廓上两个相邻齿的螺旋线之间的距离。

轴向长度（Axial Length）：轴向长度是螺旋伞齿轮齿轮齿廓沿轴线方向的长度。

齿轮直径（Pitch Diameter）：齿轮直径是指齿轮齿廓上的一个圆，该圆与齿轮齿廓的尺寸相等。

通常以毫米为单位。

齿轮宽度（Face Width）：齿轮宽度是指螺旋伞齿轮齿廓的宽度，即齿轮齿廓沿轴线方向的宽度。

这些基本参数影响着螺旋伞齿轮的性能和用途。

在设计和选择螺旋伞齿轮时，这些参数需要根据具体的应用需求来进行合理的选择。

为了确保齿轮系统的正常运行，这些参数需要与其他齿轮的参数相匹配，以确保传动的平稳和高效。

常用螺纹术语中英文对照

常用螺纹术语中英文对照常用螺纹术语中英文对照1.screw thread 螺纹2.thread 螺牙、螺距、螺齿、螺纹3.screw 螺纹、螺旋、螺钉4.thread axis 螺纹轴线5.thread pitch 螺距6.pitch of thread 螺距7.taper 锥度8.truncation 切断、削平9.chamfer 倒角10.bottom of chamfer 倒角底11.gauge 量规，测量12.difference gauge 极限量规13.external limit gauge极限量规14.plug gauge 塞规15.ring gauge 环规16.plain taper plug gauge 圆锥光滑塞规17.crest taper plug gauge 圆锥光滑塞规18.tolerance 公差19.tolerance limit 公差极限20.pipe管子21.hose 软管22.coupling联结23.external 外部的24.internal 内部的25.hand tight engagement 手紧旋合26.right-hand thread 右旋螺纹27.left-hand thread 左旋螺纹28.thread form 螺纹牙型29.root 牙底30.crest 牙顶31.major diameter大径32.minor diameter 小径33.pitch diameter 中径/doc/6318023186.html,plete thread 完整螺纹35.full thread 完整螺纹36.incomplete thread 不完整螺纹37.effective thread 有效螺纹38.threads per inch 每英寸螺纹数39.teeth per inch 每英寸齿数40.Perpendicular 垂线垂直的正交的41.cone 圆锥体42.axis 轴、中心线43.cone generatrix 锥体母线44.Perpendicular to face of cone 与圆锥体面垂直45.included angle 牙型角46.thread height螺纹牙型高度47.profile 剖面、轮廓48.reference length 基准长度49.thread reference planes 螺纹基面50.valve stem 阀杆51.cylinder neck thread 瓶口螺纹52.length of thread in cylinder neck 瓶口螺纹长度53.length of thread engagement 螺纹啮合长度54.vernier caliper 游标卡尺55.slide gauge 游标卡尺56.micrometer 千分尺57.t a p丝锥58.drill钻头59.reamer绞刀60.torque扭矩61.normal thread angle 垂直螺纹齿形角62.bisector平分线。

齿轮参数术语中英文对照总结

齿轮参数术语中英文对照总结齿轮是机械传动中常用的元件，用于将动力传递给另一个轴。

在设计和制造齿轮时，需要了解一些齿轮参数术语。

以下是齿轮参数术语的中英文对照总结。

1. Pitch circle diameter（齿距圆直径）The diameter of the imaginary circle that passes through the centers of the gear teeth.（通过齿轮齿的中心点穿过的虚拟圆的直径）2. Module（模数）The ratio of the pitch circle diameter to the number of teeth.（齿距圆直径与齿数的比值）3. Pressure angle（压力角）4. Addendum（顶隙）The distance from the pitch circle to the top of the gear tooth.（从齿距圆到齿顶的距离）5. Dedendum（根隙）The distance from the pitch circle to the bottom of the gear tooth.（从齿距圆到齿底的距离）6. Circular pitch（齿距）The distance between corresponding points on adjacent teeth, measured along the pitch circle.（相邻齿上的对应点之间的距离，沿齿距圆测量）7. Diametral pitch（齿轮密度）The number of teeth per inch of pitch circle diameter.（每英寸齿距圆直径上的齿数）8. Working depth（工作深度）The distance between the addendum and dedendum.（顶隙和根隙之间的距离）9. Face width（齿宽）The width of the gear tooth measured parallel to the axis of rotation.（平行于旋转轴测量的齿宽）10. Helix angle（螺旋角）The angle formed between the helix of the gear tooth and a plane perpendicular to the gear axis.（齿轮齿的螺旋线与垂直于齿轮轴线的平面之间形成的角度）11. Backlash（背隙）The amount of clearance or play between meshing gear teeth.（啮合齿之间的间隙或游隙的量）12. Center distance（中心距）The distance between the centerlines of two meshing gears.（两个啮合齿轮中心线之间的距离）13. Pitch point（共轭点）The point of contact between the teeth of two meshing gears.（两个啮合齿轮的齿之间的接触点）14. Arc of action（干涉线）The path traced out by the contact points between meshing gears while they rotate.（啮合齿轮旋转时接触点之间构成的路径）15. Profile shifting（型位移）The modification of gear tooth profiles to achieve specific gear ratio adjustments.（根据所需的特定齿轮传动比进行齿形调整）。

齿轮英文专业词汇

齿轮英文专业词汇分度圆直径reference diameter齿根圆直径root diameter齿顶圆直径tip diameter节圆直径pitch diameter齿根圆角半径fillet radius以下供参考\15滚动轴承滚动轴承rolling bearing单列轴承single row bearing双列轴承double row bearing装满滚动体的轴承full complement bearing 角接触轴承angular contact bearing调心轴承self-aligning bearing剖分轴承split bearing密封圈轴承sealed bearing防尘盖轴承shielded bearing预润滑轴承prelubricated bearing仪器精密轴承instrument precision bearing 锥孔轴承tapered bore bearing凸缘轴承flanged bearing推力轴承thrust bearing角接触推力轴承angular contact bearing单向推力轴承single direction thrust bearing双向推力轴承double direction thrust bearing 直线（运动）轴承linear (motion) bearing球轴承ball bearing向心球轴承redial bearing深沟球轴承deep groove ball bearing装填槽球轴承filling slot balll bearing四点接触轴承four-point contact ball bearing 滚子轴承roller bearing向心滚子轴承radial roller bearing圆柱滚子轴承cylindrical roller bearing圆锥滚子轴承tapered roller bearing滚针轴承needle roller bearing调心滚子轴承self-aligning roller bearing交叉滚子轴承crossed roller bearing轴承套圈bearing ring内圈inner ring外圈outer ring止动环locating snap ring锁圈retaining snap ring密封圈seal (bearing)防尘盖shield (bearing)滚动体rolling element滚针needle roller保持架cage成对安装（滚动轴承）paired mounting (rolling bearing)背对背配置（滚动轴承）back to back arrangement (rolling bearing) 面对面配置（滚动轴承）face to face arrangement (rolling bearing) 轴承系列（滚动轴承）bearing series (rolling bearing) 尺寸系列（滚动轴承）dimension series (rolling bearing)直径系列（滚动轴承）diameter series (rolling bearing)宽度系列（滚动轴承）width series (rolling bearing)高度系列（滚动轴承）height series (rolling bearing)外形尺寸（滚动轴承）boundary dimension (rolling bearing) 轴承宽度bearing width轴承内径bearing bore diameter轴承外径bearing outside diameter静载荷static load动载荷dynamic load摆动载荷oscillating load变载荷fluctuating load当量载荷equivalent load额定寿命rating life基本额定寿命basic rating life修正额定寿命adjusted rating life径向载荷系数radial load factor轴向载荷系数axial load factor寿命系数life factor速度系数speed factor16弹簧弹簧spring螺旋弹簧helical spring圆柱螺旋压缩弹簧cylindrical helical compression spring圆柱螺旋拉伸弹簧cylindrical helical tension spring圆柱螺旋扭转弹簧cylindrical helical torsion spring不等节距圆柱螺旋弹簧variable pitch cylindrical helical spring 多股螺旋弹簧stranded wire helical spring密圈螺旋弹簧tightly coiled helical spring截锥螺旋弹簧conical spring截锥涡卷弹簧volute spring平面涡卷弹簧spiral spring碟形弹簧belleville spring环形弹簧ring spring板弹簧leaf spring等刚度弹簧constant rate (stiffness) spring变刚度弹簧variable rate (stiffness) spring组合弹簧combined spring片弹簧flat spring橡胶弹簧rubber spring空气弹簧air spring节距(弹簧) pitch (spring)自由高度(弹簧) free height (spring)工作高度(弹簧) working height (spring)工作载荷specified load极限载荷ultimate load总圈数total number of coils有效圈数effective coil number极限高度height under ultimate load弹簧中径mean diameter of coil旋绕比(弹簧) spring index (spring)曲度系数(弹簧) curvature correction factor (spring) 高径比(弹簧) slender ratio (spring)压并载荷(弹簧) solid load (spring)压并高度(弹簧) solid height (spring)扭转角torsion angle弹簧柔度flexibility of spring17传动一般传动装置transmission, driving传动比speed ratio, transmission ratio增速比speed increasing ratio减速比speed reducing ratio无级变速infinitely variable speed减速器speed reducer18齿轮传动齿轮传动gear drive齿轮gear平行轴齿轮传动gear drive with parallel axes相交轴齿轮传动gear drive with intersecting axes交错轴齿轮传动gear drive with non-parallel non-intersecting axes 小齿轮pinion大齿轮wheel, gear主动齿轮driving gear从动齿轮driven gear外齿轮external gear内齿轮internal gear中心距center distance齿数比gear ratio连心线line of centers轴交角shaft angle轴平面axial plane基准平面datum plane法平面normal plane基本齿廓basic rack tooth profile 基本齿条basic rack产形齿条counterpart rack轮齿gear teeth齿槽tooth space左旋齿left-hand teeth右旋齿right-hand teeth齿面tooth flank同侧齿面corresponding flanks异侧齿面opposite flanks工作齿面working flank非工作齿面non-working flank相啮合齿面mating flank共轭齿面conjugate flank齿根过渡曲面fillet齿顶crest齿槽底面bottom land齿廓tooth profile端面齿廓transverse profile法向齿廓normal profile轴向齿廓axial profile背锥齿廓back cone tooth profile 渐开线齿廓involute profile 直线齿廓straight-side profile摆线齿廓cycloidal profile圆弧齿廓circular arc profile共轭齿廓conjugate profile齿高tooth depth齿顶高addendum齿根高dedendum弦齿高chordal height齿宽facewidth齿厚tooth thickness模数module端面模数transverse module法向模数normal module轴向模数axial module径节diametral pitch节径pitch diameter齿数number of teeth当量齿数virtual number of teeth 头数number of threads 圆柱螺旋线circular helix圆锥螺旋线conical spiral螺旋角helix angle导程lead导程角lead angle阿基米德螺线Archimedes spiral摆线cycloid长幅摆线prolate cycloid短幅摆线curtate cycloid外摆线epicycloid长幅外摆线prolate epicycloid短幅外摆线curtate epicycloid内摆线hypocycloid渐开线involute延伸渐开线prolate involute缩短渐开线curtate involute球面渐开线spherical involute阿基米德螺旋面screw helicoid球面渐开螺旋面spherical involute helicoid 圆环面toroid 干涉interference齿廓修形profile modification修缘tip relie齿向修形axial modification齿端修薄end relief鼓形齿crowned teeth根切（挖根）undercut啮合engagement啮合线path of contact端面啮合线transverse path of contact啮合曲面surface of action作用角angle of transmission总作用角total angle of transmission作用弧overlap arc总作用弧total overlap arc端面重合度transverse contact ratio纵向重合度overlap ratio重合度contact ratio标准中心距reference center distance名义中心距nominal center distance径向变位addendum modification正变位positive addendum modification负变位negative addendum modification非变位齿轮X-zero gear变位齿轮gear with addendum modification径向变位量addendum modification (for external gears)径向变位系数addendum modification coefficient变位齿轮副X-gear pair, modified gear pair角变位齿轮副gear pair with modified center distance正角变位齿轮副gear pair with positive modified center distance 负角变位齿轮副gear pair with negative modified center distance 高变位齿轮副gear pair with reference center distance 中心距变动系数center distance modification coefficient传动误差transmission error传动精度transmission accuracy齿轮承载能力load capacity of gears圆柱齿轮cylindrical gear齿条rack当量齿轮virtual gear直齿轮spur gear斜齿轮helical gear交错轴斜齿轮副crossed helical gear pair人字齿轮herringbone gear ,double helical gear渐开线圆柱齿轮involute cylindrical gear圆弧圆柱齿轮circular-arc gear单圆弧齿轮single-circular-arc gear双圆弧齿轮double-circular-arc gear分度圆柱面reference cylinder基圆base circle分度圆reference circle节圆pitch circle齿顶圆tip circle齿根圆root circle分度圆螺旋线reference helix节圆螺旋线pitch helix基圆螺旋线base helix齿距pitch轴向齿距axial pitch法向齿距normal pitch公法线长度base tangent length分度圆直径reference diameter齿根圆直径root diameter齿顶圆直径tip diameter节圆直径pitch diameter齿根圆角半径fillet radius端面齿厚transverse tooth thickness法向齿厚normal tooth thickness端面弦齿厚transverse chordal tooth thickness 法向弦齿厚normal chordal tooth thickness齿槽宽spacewidth齿厚tooth thickness齿厚半角tooth thickness half angle 端面压力角transverse pressure angle 法向压力角normal pressure angle压力角pressure angle齿形角normal pressure angle啮合角working pressure angle顶隙bottom clearance圆周侧隙circumferential backlash 法向侧隙normal backlash。

齿轮英文术语

A.1. abrasive tooth wear 齿面研磨磨损2. absolute tangential velocity 绝对切向速度3. accelerometer 加速表4. addendum 齿顶高5. addendum angle 齿顶角6. addendum circle 齿顶圆7. addendum surface 上齿面8. adhesive wear 粘着磨损9. adjustability 可调性10. adjustability coefficients 可调系数11. adjusting wedge 圆盘端铣刀的可调型楔块12. allowable stress 允许应力13. alternate blade cutter 双面刀盘14. angular backlash 角侧隙15. angular bevel gears 斜交锥齿轮16. angular displacement 角移位17. angular pitch 齿端距18. angular testing machine 可调角度试验机19. approach action 啮入20. arbor 心轴21. arbor distance 心轴距22. arc of approach 啮入弧23. arc of recess 啮出弧24. attraction 收紧25. average cutter diameter 平均刀尖直径26. axial displacement 轴向位移27. axial factor 轴向系数28. axial locating surface 轴向定位面29. axial pitch 轴向齿距30. axial plane 轴向平面31. axial rakeangle 轴向前角32. axial thrust 轴向推力33. axle testing machine 传动桥试验机B.1．back angle 背锥角2．Back angle distance 背角距（在背锥母线方向）3．Back cone 背锥4．Back cone distance 背锥距5．Back cone element 背锥母线6．Backlash 侧隙7．Backlash tolerance 侧隙公差8．Backlash variation 侧隙变量9．Backlash variation tolerance 侧隙变量公差10．Bandwidth 频带宽11．Base circle 基圆12．Base diameter 基圆直径13．Base pitch 基节14．Base radius 基圆半径15．Base spiral angle 基圆螺旋角16．Basic rack 基本齿条17．Bearing 轴承18．Bearing preload 轴承预负荷19．Bearing spacing／spread 轴承间距20．Bending fatigue 弯曲疲劳21．Bending stress 弯曲应力22．Bevel gears 锥齿轮23．Bias 对角接触24．Bias in 内对角接触25．Bias out 外对角接触26．Blade angle 刀齿齿廓角27．Blade edge radius 刀尖圆角半径28．Blade letter 刀尖凸角代号29．Blade life 刀尖寿命30．Blade point width 刀顶宽31．Blank offset 毛坯偏置距32．Bland position 毛坯位置33．Bottom land 齿槽底面34．Boundary lubrication 界面润滑35．Breakage 破裂36．Bridged contact pattern 桥型接触斑点37．Broach 拉刀38．Burnishing 挤齿C．1. Case crushing 齿面塌陷2. CBN 立方氮化硼3. chamfer 倒角4. chordal addendum 弦齿高5. chordal thickness 弦齿厚6. chuck 卡盘7. circular broach 圆拉刀8. circular face-mill 圆盘端面铣刀9. circular peripheral-mill 圆盘铣刀10. circular pitch 周节11. circular thickness 弧齿厚12. circular thickness factor 弧齿厚系数13. clearance 顶隙14. clearance angle 后角15. coarse pitch 大节距16. coast side 不工作齿侧17. combination 组合18. combined preload 综合预负荷19. complementary crown gears 互补冠状齿轮20. completing cycle 全工序循环21. composite action 双面啮合综合检验误差22. compressive stress 压应力23. concave side 凹面24. concentricity 同心度25. concentricity tester 同心度检查仪26. cone distance 锥距27. cone element 锥面母线28. conformal surfaces 共型表面29. coniskoid 斜锥齿轮30. conjugate gears 共轭齿轮31. conjugate racks 共轭齿条32. contact fatigue 接触疲劳33. contact norma 接触点法线34. contact pattern (tooth contact pattern) 轮齿接触斑点35. contact ratio 重合度36. contact stress 接触应力37. continuous index 连续分度38. control gear 标准齿轮，检验用齿轮39. convex side 凸面40. coolant 冷却液41. corrosive wear 腐蚀性磨损42. corrugated tool 阶梯刨刀43. counter forma surfaces 反法向表面44. cradle 摇台45. cradle test roll 摇台角46. cross 大小端接触47. crossing point 交错点48. crown 齿冠49. crown circle 锥齿轮冠圆50. crowned teeth 鼓形齿51. crown gear 冠轮52. crown to back （轮冠距）轮冠至安装定位面距离53. crown to crossing point 轮冠至相错点距离54. cutter 刀盘55. cutter axial 刀盘的轴向位置56. cutter axial plane 刀盘轴向平面57. cutter axis 刀盘轴线58. cutter diameter 刀盘直径59. cutter edge radius 刀刃圆角半径60. cutter head 刀盘体61. cutter number 刀号62. cutter parallel 刀盘平垫片63. cutter point diameter 刀尖直径64. cutter point radius 刀尖半径65. cutter point width 刀顶距66. cutter spindle 刀盘主轴67. cutter spindle rotation angle 刀盘主轴转角68. cutting distance 切齿安装距69. C.V. testing mashing 常速试验机70. cyclex 格里森粗铣精拉法圆盘端铣刀71. cylindrical gears 圆柱齿轮D.1．Datum tooth 基准齿2．Debur 去毛刺3．Decibel (CB) （噪音）分贝4．Decimal ratio 挂轮比值5．Dedendum 齿根高6．Dendendum angle 齿根角7．Dedendum surface 下齿面8．Deflection 挠曲9．Deflection test 挠曲试验10．Deflection testing machine 挠曲试验机11．Depthwise taper 齿高收缩12．Design data sheet 设计数据表13．Destructive pitting 破坏性点蚀14．Destructive wear 破坏性磨损15．Developed setting 试切调整16．Dial indicator 度盘式指示表17．Diametral pitch 径节18．Diamond 菱形接触19．Dinging ball check 钢球敲击检查20．Disc-mill cuter 盘铣刀21．Dish angle 凹角22．Displacement 位移23．Displacement error 位移误差24．Double index 双分度25．Double roll 双向滚动26．Down roll 向下滚动27．Drive side 工作齿侧28．Duplete 双刃刀29．Duplex 双重双面法30．Duplex helical 双重螺旋法（加工方法之一）31．Duplex spread blade 双重双面刀齿（加工／磨齿方法）32．Duplex taper 双重收缩齿33．Durability factor 耐久系数34．Dynamic factor 动载荷系数E。

齿轮英文术语

齿轮参数中英文对照

EXTERNAL SPUR GEAR DAT外圆柱齿轮参数）manufacturing data （制造参数）part number （零件号）tooth form （齿面）gear type （齿轮类型）number of teeth （齿数）normal module （法向模数）normal pressure angle （at ref circle）法向压力角（在分度圆上）helix angle （at ref circle）螺旋角（在分度圆上）helical lead （螺旋导程）hand of helix （旋向）reference face width （参考齿宽）outside diameter （齿顶圆直径）chamfer diameter （倒圆直径）reference（pitch）circle diameter （分度圆直径）或节圆start of active profile diameter 有效渐开线起始圆直径form diameter 展成直径root diameter 齿根圆直径base circle diameter 基圆直径whole depth 全齿高normal circular tooth thickness （at reference circle）法向弧齿厚（在分度圆上）root type 齿根形式root fillet radius 齿根圆角半径lead crown 齿向鼓形0.075mm ）HOB DATA 滚刀参数 pressure angle 压力角tooth thickness at reference line 分圆齿厚 protuberance 凸角 tip radius 齿顶圆半径 reference part number 零件号 INSPECTION DAT 检验数据profile tolerance and modifications 齿形公差和修形 profile hollow 齿形中凹refernce pitch circle runout 节圆跳动 pitch variation 齿距偏差 lead variation 齿向偏差 lead hollow 齿向中凹profile surface finish 渐开线齿面精加工 ball diameter 量球直径dimension over two balls in same plane 跨棒距 REFERENCE DATA-MATING GEAR 齿齿的参考参数 normal center distance 中心距mating gear part number 对齿齿轮零件号 mumber of teeth on mating gear 对齿轮齿数backlash （nominal CD ,ROOM TEMP 侧隙（法线方向，室温） general notes （通用技术要求）1. DO not scale drawing （不要在图上量取尺寸）2. all surfaces corners and edges must be free from burrsand sharp edges-break 0.075 MM MAX （所有面 ,角和边不能有毛刺 ,锐边倒钝不超过 3. unless otherwise stated （除非特别注明 ,否则）A.all dimensions and tolerance are in millimeters perChi nese sta ndard（所有以毫米为单位的尺寸和公差均按中国标准）B. all surface finishes to be 3.2 micrometer or better（所有表面粗糙度不应低于3.2）C. all dimension are finished dimensions;no allowance has beenmade for any change in maximum or least material conditiondue to heat treatment（所有尺寸均为最终尺寸; 热处理导致的最大或最小实体条件的变化不应超出允差）D linear dimensions to be +/- 0.25 MM（线性尺寸偏差为+/- 0.25 MM）E angular dimensions to be +/- 0.5 o（角度尺寸偏差为+/- 0.5o）4. mark part number as shown（如图作零件号）5. mark serial number as shown（如图作系列号）6. heat treatment to be applied to all surfaces（整体热处理）gear notes（齿轮技术要求）1. do not grind roots and fillets after heat treatment（热处理后不得磨及齿根和圆角）2. no steps or grooves permissible in root and fillet region afterhoning or grinding（珩磨后,齿根和圆角区域不允许有台阶或凹痕）3. profile tolerance based upon floating band fit（齿形误差应以公差带为计）4. gear must be free from grind burns and tempering（齿面不得烧伤）5. pitch line runout and other tooth tolerances are with respect todatum A（节圆跳动和其它齿轮公差均以基准A为测量基准）6. profile tolerance to be measured between form and chamfer（齿形误差应由渐开线起始（或终止）圆测量至齿顶倒角）7. min hardness must be achieved in tooth root and fillet region（齿根和圆角处的硬度不得低于硬度下差）8. root radius tangent to profile not to extend above form diameter（齿根圆角要与齿面相切,而且不能超过渐开线起始（或终止）圆直径。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

螺旋伞齿轮 外文术语

与齿轮相关地英语词汇总情况结

齿轮基本术语中英文对照

齿轮术语中英文对照

中英文齿轮基本术语

齿轮术语 英语词汇

齿轮之种类与名称翻译

齿轮术语中英文对照表

齿轮术语的英文翻译

齿轮术语中英文对照表

螺旋伞齿轮的基本参数

常用螺纹术语中英文对照

齿轮参数术语中英文对照总结

齿轮英文专业词汇

齿轮英文术语

齿轮英文术语

齿轮参数中英文对照

螺旋伞齿轮外文术语

齿轮术语英语词汇