模具设计工程师,口语对话AA
模具英语口语
产品检讨1. 和滑块干涉的倒勾请加料填平至滑块可以顺利滑动(The undercut area where interfere with slide block need to be filled material to help the slider can move smoothly.)2. 加肉太多(The thickness is added too thick.)3. 加肉面积太大(The thickening area is too wide.)4. GATE位置移位(Gate position is moved.)5. 滑块拆的位置(The split line of slide block or the area of slide.)6. 此处有尖角，填充困难(This area is hard to be filled due to the sharp feature.)7. 此处钢材太薄，强度不足而且不容易冷却(The strength of this area is too weak and isn’t easy to get cold due to the steel too thin.)8. 圆柱特征要有一半圆不可以拆在滑块上，以免粘滑块造成拉白，拉断(The semicircle of cylinder avoids designing on slide block lest it will be pulled apart or cause drag mark)9. 此处做斜销在作动时会削到成品肉厚(The part will get damage if we make lifter in this area.)10. 这个面是装配面，不能加料(This is critical surface where is not allow to add material.)11. 此处料位太厚，会有缩水，建议减料改善(Owing to the shrinkage of the thickness that we suggest to reduce some wall thickness to improve it.)12. 此面是不是外观面，此处做滑块的话会有夹线，是否可以接受(Please confirm whether it is critical surface or not. Please confirm whether it is acceptable to has Slide split line if we have slide in this area. )13. 此处有倒勾，能否减料，使公母模靠破，不做滑块和斜销(Please confirm whether we can reduce material to the area where have undercut as indicated to have shut off on cavity side. No slide block and lifter to be made. )14. 请尽快确认这种拆模方式和结构，否则会影响模期(Please confirm the issues of Parting line, Gate position...Etc otherwise the lead-time will be extended.)15. 此面是否有特殊要求，能否有顶针印(Please confirm whether it is a critical surface or not and can we haveE.J. pin mark on it.)16. P.L面开在此处，模具上会有尖角和刀口，对模具寿命有影响(There are sharp edges if set the parting line at here, It will reduce the tool life)17. 加大拔模角，以便脱模顺利(We would suggest to enlarging draft to help tool released.)18. GATE做在此处的话有两个缺点：1.盖子打开时可以看到GATE的修剪部位; 2.两个斜销在同一侧，顶出也不是很平衡.(Two imperfect points if the gate is to be designed in this area as below:a). Easy to see the gate mark when you open the cap.b). Unbalance of ejector when two lifters are at the same side)19. GATE做在此处的话.盖子打开后看不到GATE的修剪部位(The gate mark is not visual if the gate position is design like it.)20. 如果GATE一定要做在你们指定的位置的话，那还不如做在这一侧，这样的话还可以减小这个位置的缩水(If you insist that the gate position have to be as original design then we would further recommend to have it to the area where indicate as it can avoid shrink problem in this area.)21. 在此处GATE做潜顶针的话，背后的外观面会有冲料痕，而且成品又是黑色的，会最明显(If the gate type has to be design as sub. gate then the back surface of part will have flow mark with serious due to black colour.)22. P.L开在此处不合理，模具加工困难，P.L应改为和图示的一样(This area is not suitable to have Parting line as the tool will become more complicate therefore we recommend to have Parting line as indicated.)23. 此成品粘母模的机会很大，能否在公模加倒勾，拉料顶针或者公模保留E.D.M 纹，开模时使成品留在公模一侧(It is possible sticking on cavity, therefore, please confirm whether it can make undercuts, snatch pins or leave coarse E.D.M. on core to snatch part on)24. 此处料厚段差很大，成品表面会有应力痕，是否接受(Please confirm whether it is acceptable to has stress line on surface, it is cause to the thickness isn’t equally.)25. 请注明何处为外观面，能否提供2D图和注意事项(Please advise where is the critical surface. Please also provide us 2D drawing with critical dimensions. )26. 红色所示处是有问题的地方，请特别注意(Please pay more attention to the area where highlighted as red colour as this area have problem.)27. 成品设计此处有问题，建议如下图所示修改(We would suggest to have part design as attached as the current designhave problem.)28. 此处改为一个球形的凹槽(We would suggest to modify it as a globe recess.)29. 圆柱特征要有一半不可以拆在滑块里，以防拉断(this issue same as no.8)30. 此处大滑块上走小滑块，小滑块要先退，大滑块要做延迟(The inside small slide block will recede first and the parent slide block have to postpone sliding.)31. 滑块要用液压油缸抽芯以保证开合模顺序(The slide pins will use oil cylinder to assure the process in proper order.)32. 这个面有装配，加料的话装配时会顶住，如图所示(This surface can not add material where will intervene between two parts as it is assembly. Please see the sketch as attached. )33. 可降低斜销面，增加成品些许肉厚来做变化(To descend the surface of lifter in order to thicken the part.) 34. 一半做斜销，一半做自然(Half side with Lifter and half side with solid / nature.)35. 此处两个柱子重迭，有倒勾，不能做自然，要做SLIDE(These two bosses are overlapping with undercut therefore it can not be made as solid. We suggest to making it as slide block.)36. 此处强迫顶出(This area need to be as force ejection.)37. 公模两段开模，这个地方先退(Here will be fore receding as double ejection.)38. 此处做镶件会有夹线，能否接受(Please confirm whether it is acceptable that here will have a split line.)39. 此面公母模1度靠破，会有段差，可否接受(Please confirm whether it is ok to have mismatch to the area where have 1 degree of shut off in Core / Cavity side.)40. 这个尺寸能否加大(Please confirm whether we can enlarge this dimension.)41. 此处加一个凹槽，胶片的弹出效果会更好一些，试模后看装配的效果再做修正(It will be effect better elastic of film if it adds a recess. See how it is effect on assembly parts, and then make further decision.)42. 此处有倒勾，建议将剖面线所示部位CUT即可避免此处的倒勾(Here has undercut, we suggest to cutting out the indicated part as it highlight to avoid undercut.)43. 成型后SUB GATE要修平(The gate (sub gate) need to be trimmed evenly after moulded.)44. 此处倒勾先垂直顶出，之后再手动取出(This area of undercut needs to be ejected as vertical then take it out manually.)45. 这两个面都有滑块，GATE改在此处改不到(The gate is not suitable in this area as there is two slide blocks seal off this area.)46. 此处加做一个旋转GATE，射出时方便调整成品的质量(We would suggest to placed a runner shut-off insert to adjust the volume of part filling.)47. 此倒勾在滑块上强迫脱模，倒勾是否可以减小到0.6(This undercut will be force ejected out, Please confirm whether it can be reduced to 0.6 mm.)48. 此柱子无法脱模，请确认是否是在转图时错位，能否提供客户的原始图档(This boss is not releasable. Please check file again and if possible pleas e-send us native data. )49. 此柱子是实心的，会缩水(This boss will shrink due to it is solid boss.)50. 这个面是否要咬花，咬花番号是什么，最小的拔模角要多大(Please confirm whether this surface need to be textured or not? Please advise texture spec. And what's the min. draft. )51. 这个面是否要打光，贴标签(Please confirm whether this surface need to be polished and stuck on a sticker or not?)52. 红色显示的几个面拔模角太小，出模时会拉伤，建议加大拔模角(The areas where highlighted as red colour have problem of small draft angle and we would suggest to enlarging draft to avoid the part cause dragging mark.)53. 此RIB太薄，会填充不足This rib can not be filled properly due to too thin.54. 此RIB太厚，会缩水This rib will have shrink problem due to too thick.55. 此处倒勾出模困难，建议先不做倒勾，成型后再二次加工，但要做治具，费用要另外算(We would recommend doing this undercut as second operation as current design have problem to build a tool. And the jig cost will be occurred. ) 56. 柱子底部都要做火山口(The base of all bosses are required a crater to avoid shrinkage.) 57. XXX,你现在有空吗？我可以问你一些问题吗？Could I ask you some questions if you are free ?/ Are you free now ?MayI ask you same questions ( a question)?58.请问次产品的面是否为外观面？表面做什么处理？是晒纹/抛光？Can you tell me weather the surface of this part is a visible / estheticone ? What will we do for its surface? Texture or polishing ?59.请问产品这个面是否可加顶针或顶块？产品允许加扁顶针吗？Does this part need an ejector pin or an ejector bar? Can we add an ejector blade?60. 这个产品的柱位我们打算做司筒或镶针，可以吗？Can we add ejector sleeves or ejector pins in the boss of this part.61.产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？There’s an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK?62 产品里面的这个位置我打算做斜顶或内行位，有问题吗？We will make the lifter and (inner) slider in the position, will that bea problem?63 你提供的2D产品图与3D产品图不一致，请问以哪个图为准？The 2D and 3D drawing you provided is not the same , can you tell me which one is correct ?64 你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太薄，这些产品我们可以自己修改吗？修改后会交给你确认。
模具设计岗位招聘面试题及回答建议(某大型央企)
招聘模具设计岗位面试题及回答建议(某大型央企)面试问答题（总共10个问题）第一题题目：请描述一下您在过去的工作或项目中，遇到的最具挑战性的模具设计问题是什么？您是如何分析和解决这个问题的？答案：在过去的项目中，我遇到的最具挑战性的模具设计问题是设计一款高精度、复杂结构的汽车零部件模具。
该模具要求极高的尺寸精度和表面光洁度，同时还需要满足高速生产线的生产效率要求。
解决步骤：1.问题分析：首先，我与项目团队一起分析了模具设计的技术要求和生产线的特性。
我们确定了主要问题集中在模具的定位精度、冷却系统设计以及模具材料选择上。
2.方案优化：为了提高定位精度，我采用了高精度导柱导套系统，并优化了模具的导向结构。
针对冷却系统，我设计了一套多通道、多级冷却系统，以确保模具在高速生产过程中保持稳定温度。
3.材料选择：我选择了耐高温、高强度、耐磨性的模具钢，并进行了预硬处理，以减少后续热处理变形。
4.模拟分析：在模具设计初期，我利用有限元分析软件对模具结构进行了模拟分析，提前预测了可能出现的应力集中和变形问题，并进行了相应的结构优化。
5.团队合作：我与工程师、工艺师和生产团队紧密合作，确保模具设计能够满足生产线的实际需求。
结果：经过以上努力，该模具最终成功投入使用，不仅满足了设计要求，还提高了生产效率，降低了生产成本。
解析：这道题目考察的是应聘者对复杂模具设计问题的处理能力。
通过上述答案，可以看出应聘者具备以下能力：•问题分析能力：能够准确识别和定位问题。
•解决方案设计能力：能够提出有效的解决方案。
•技术应用能力：能够运用专业知识和工具进行设计优化。
•团队合作能力：能够在团队中发挥积极作用，确保项目顺利进行。
•结果导向能力：能够关注最终目标，确保项目成功实施。
第二题题目：请描述一次您在模具设计过程中遇到的挑战，以及您是如何解决这个问题的。
答案：在我负责的一个项目中，我们需要设计一款高精度、复杂结构的汽车零部件模具。
模具英语100句
如何用英文和老外检讨模具(2008-1-16 08:50)1．XXX！你现在有空吗，我可以问你一些问题吗？Could I ask you some questions？May I ask you some questions (a question)?2．请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its surface? Texture or Polishing?3．请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗？Does this part need an ejector pin or an ejector bar? Can we add an ejector blade?4．这个产品的柱位我们打算做司筒。
（或镶针）可以吗？Can we add ejector sleeves or ejector pins in the boss of this part?5．产品的这个位置有倒扣不能出模，我们打算做行位，在此面上会有分模线，你接受吗？There's an undercut at this position that can not be molded, we plan to make a slider for it. It will also have a parting line on this side, is that OK?6．产品里面的这个位置我们打算做斜顶或内行位，有问题吗？We will make the lifter and (inner) slider in this position, will that be a problem?7．你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？The 2D and 3D drawings you provided are not the same, could you advise which one is correct?8．你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问题我们可以自己修改吗？修改后会给交给你确认。
模具工程师面试题及答案(全)
模具工程师面试题及答案1.请介绍一下你的模具设计经验？答：我曾在模具设计方面工作了五年，主要从事模具设计和开发工作，熟悉模具设计流程、工具和软件，具有良好的团队合作能力和创新意识。
2.请列举你掌握的模具设计软件？答：我掌握SolidWorks、AutoCAD、ProE等多种模具设计软件，具有良好的设计和绘图能力，可以根据客户要求进行快速准确的设计。
3.请描述一下你的模具制造经验？答：我在模具制造方面工作了三年，主要从事模具加工和制造工作，熟悉模具加工工艺和操作规程，能够独立完成各种模具的加工和制造。
4.请谈一下你的模具维修经验？答：我曾在模具维修方面工作了两年，主要从事模具维修和保养工作，能够熟练掌握各种模具的维修和保养方法，确保模具的正常使用。
5.请问你在模具设计中的主要创新点是什么？答：我认为模具设计中最重要的创新点是结合生产工艺和客户需求，利用先进的技术和工具进行设计，提高模具的精度和效率。
6.请问你如何保证模具的制造精度？答：我会在设计阶段注重模具的结构和尺寸的精度要求，对模具加工过程进行严格的质量控制，确保模具的精度符合要求。
7.请谈一下你在模具制造过程中的主要挑战是什么？答：我认为在模具制造过程中的主要挑战是加工和制造工艺的不断提高和更新，需要及时掌握新技术和工具，不断提高自己的技能和能力。
8.请问你在模具设计中如何考虑模具的寿命？答：我会在设计阶段考虑模具的使用寿命和保养要求，根据模具的材料和使用环境进行合理的设计和选择，以提高模具的使用寿命。
9.请问你如何处理模具在生产中的故障？答：我会根据故障的情况对模具进行分析和排查，找出故障原因并采取相应的维修措施，确保模具在生产中的正常使用。
10.请问你在模具设计中如何考虑模具的可维修性？答：在模具设计中，我会考虑模具的易维修性和保养要求，对模具的结构和细节进行合理的设计和选择，以便在模具出现故障时能够快速准确地维修和保养。
11.请问你如何评估模具的制造成本和周期？答：在模具制造过程中，我会根据模具的复杂程度、材料、工艺等因素评估模具的制造成本和周期，并制定相应的计划和措施，以确保模具的质量和效率。
模具工程师岗位面试题及答案(经典版)
模具工程师岗位面试题及答案1.请简要介绍一下您的模具工程师背景。
答案：我拥有X年的模具工程师经验。
我在不同行业的模具设计、制造和优化方面有丰富的经验，尤其擅长在复杂项目中找到创新的解决方案。
2.能否分享一个您成功解决复杂模具设计问题的案例？答案：曾经，在一个高精度塑料模具项目中，我遇到了冷却不均匀导致产品变形的问题。
通过仿真和重新设计冷却系统，我成功降低了变形率，并提高了生产效率。
3.在模具设计中，如何平衡产品质量和制造成本？答案：我会首先优化设计以确保产品质量，然后考虑材料和制造工艺的可行性。
例如，我曾在汽车零部件模具中使用高强度材料，通过复杂的制造流程来确保产品质量和寿命。
4.您在如何减少模具生产周期方面有什么经验？答案：通过标准化部件、采用先进的加工技术以及优化流程，我成功地将一个模具项目的生产周期从X减少到Y。
5.在工程变更时，您如何管理模具设计的更新和调整？答案：我会建立清晰的变更管理流程，确保任何变更都得到充分评估，并与相关团队紧密合作，以确保模具设计的一致性和有效性。
6.您如何保证模具设计的可维护性和可持续性？答案：我注重模具结构的简洁性和标准化，以便于维护和维修。
在设计中考虑易损部件的更换，以延长模具的使用寿命。
7.请分享一个您在团队合作中解决冲突的经验。
答案：在一个紧急项目中，意见分歧导致进度受阻。
我组织了一次跨职能的会议，明确问题并倾听每个人的观点，最终找到了一个共同的解决方案，成功地推进了项目。
8.如何在设计过程中考虑制造和加工的可行性？答案：我在设计早期就与制造团队合作，了解他们的建议，并根据可行性分析做出调整。
例如，我在设计金属模具时会考虑到加工难度和工具可用性。
9.您如何评估新材料在模具设计中的应用潜力？答案：我会进行材料测试和仿真，评估其物理特性、耐用性和加工性能。
例如，我曾成功引入新型高温塑料材料，为耐高温模具设计带来了显著改进。
10.在设计模具时，如何确保产品的尺寸精度和一致性？答案：我会使用精密的CAD工具进行设计，并与测量团队紧密合作，以确保模具的尺寸满足严格的要求。
模具英语口语对话
模具口语对话1）、这套模具资料都清楚了吗？1、是的，这套模具资料很清楚了；2、没有，我还有些地方需要和你再确认一下；3、现在，我们有基本的信息，例如：模穴数，产品材料，注塑机资料和模具材料等，但我们还没有标准件的标准，浇口要求和产品表面要求。
1)Is everything clear on this mould?(Any question on this mou ld?)--Yes,everything is clear.--No,I need to confirm some questions with you.--Now,we have the basic information,such as:cavity number, product material,moulding machine specifications and steel in formation etc.But we do not have the standard of spare parts,g ate requirements and the surface requirement of the part.2）、这个产品有没有问题？1、没有问题，客户很专业；2、我检查到了以下问题：A.除了骨位以外，大部分都加了拨模角。
它不会影响模具结构；B.没加拨模角。
我没有办法确认产品的分型面和模具结构。
2)Any question on this product?--No.Our customer is very professional.--I found the following problems after checking it:A.The draft angle is almost added except for some ribs.It will not affect the mould structure.B.No draft angle on the part.We can not confirm the parting lin e and the mould construction.3）、模具有没有薄钢位？1、有，这里就有薄钢位,模具强度会受影响；2、我仔细检查了产品的3D图，没有看到薄钢位，我如果以后发现了，我会立即告诉你。
模具项目工程师面试题
模具项目工程师面试题一、岗位背景介绍模具项目工程师是专门从事模具工程设计、制造和管理的职业，对模具工程项目进行全方位的规划与控制，以确保项目的质量、进度和成本的控制与管理。
二、技术能力要求作为一名模具项目工程师，需要具备以下技术能力：1.模具设计能力：熟悉模具工艺流程，能够独立完成模具的设计，并满足项目需求。
2.模具制造技术：了解模具加工工艺，能够协调模具制造过程中的各个环节，确保质量和进度。
3.项目管理能力：具备项目管理经验，能够有效规划、组织和控制项目，实现项目目标。
4.团队协作能力：良好的沟通能力和团队合作精神，能够与项目团队成员紧密配合，共同完成项目任务。
三、面试题目1.请介绍一下您的模具设计经验和技术背景。
2.您是否熟悉常用的模具设计软件？请列举并简要介绍您熟悉的软件。
3.描述一下您如何进行模具项目的规划和组织管理。
4.在模具项目中，您在质量控制方面有什么实施的经验或策略？5.请分享一次您处理模具项目中的紧急情况的经历，并说明您是如何解决的。
6.在模具项目中，您如何确保项目进度和成本的控制？7.您与项目团队成员如何协作与沟通，以确保项目的顺利进行？8.在您的项目经验中，是否遇到过模具项目失败的情况，您是如何处理的？9.您是否了解模具制造中的新技术和新材料？请分享您对其中一项技术或材料的了解。
10.您对自己未来在模具项目工程师岗位上的发展有哪些规划和期望？四、面试答题技巧1.回答问题时，要突出自己的经验和实践，用具体事例或项目来支持说辞。
2.对于技术问题，要清晰、简洁地回答，用专业术语表达自己的能力和知识。
3.回答问题时，尽量展示自己的解决问题的思路和方法，体现项目管理能力和团队协作能力。
4.要注重礼貌和谦虚，表达对面试机会的感谢和对公司的兴趣。
五、总结模具项目工程师是一个需要全面技术能力、良好项目管理经验和团队合作能力的职位。
通过合理的项目规划与组织管理，严格的质量控制，以及有效的沟通与协作，模具项目工程师能够实现模具项目的成功交付，为企业的发展做出贡献。
模具工程师必备英语口语
1. The undercut area where interfere with slide block need to be filled material to help the slide can move smoothly.（和滑块干涉的倒勾请加料填平至滑块可以顺利滑动）2. The thickening added too thick.(加肉太多)3. The thickening area is too wide.（加肉面积太大）4. Gate position is moved.(GATE位置移位)5. The split line of slide block or the area of slide.(滑块拆的位置)6. This area is hard to be filled due to the sharp feature(此处有尖角，填充困难)7. The strength of this area is too weak and isn’t easy to get cold due to the steel too thin.8. ( 此处钢材太薄，强度不足而且不容易冷却)9. .The semicircle of cylinder avoids designing on slide block lest it will be pulled apart or cause drag mark.10. ( 圆柱特征要有一半圆不可以拆在滑块上，以免粘滑块造成拉白，拉断.)11. The part will be damaged if we make lifter in this area.12. ( 此处做斜销在作动时会削到成品肉厚)13. This is critical surface where is not allow to add material.14. ( 这个面是装配面，不能加料)15. This thick wall area might because sink mark, Please reduce some wall thickness to improve it.)16. ( 此处料位太厚，会有缩水，建议减料改善)17. Please confirm whether it is critical surface or not. Please confirm whether it is acceptable to has Slide split line if we have slide in this area.18. （此面是不是外观面，此处做滑块的话会有结合线，是否可以接受）19. Please confirm whether we can reduce material to the area where have undercut as indicated to have shut off on core and cavity side. No slide block and lifter to be made.20. （此处有倒勾，能否减料，使公母模靠破，不做滑块和斜销）21. Please confirm the issues of Parting line, Gate position...Etc otherwise thelead-time will be extended.22. （请尽快确认这种拆模方式和结构，否则会影响模期）23. The trim mark of the gate is not visual after open the top case if the gate position is design ed like it24. （GATE做在此处的话.盖子打开后看不到GATE的修剪部位）25. We would suggest to enlarging draft to help tool released.)26. 加大拔模角，以便脱模顺利）27. There are sharp edges if set the parting line at here, It will reduce the tool life28. （P.L面开在此处，模具上会有尖角和刀口，对模具寿命有影响）29. If you insist that the gate position have to be as original design then we would further recommend to have it to the area where indicate as it can avoid shrink problem in this area.（如果GATE一定要做在你们指定的位置的话，那还不如做在这一侧，这样的话还可以减小这个位置的缩水）1．XXX！你现在有空吗，我可以问你一些问题吗？Could I ask you some questions if you are free?/ Are you free now? May I ask you some questions (a question)?2．请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its surface? Texture or Polishing?3．请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗？Does this part need an ejector pin or an ejector bar? Can we add an ejector blade? 4．这个产品的柱位我们打算做司筒。
最全模具英语,老外客户对话, 单词
This sample has been burned in the bottom because the venting is not good, we can add an insert in the middle of the rib. 15． 重 做镶件大 约需要56天时 间，你能 接受吗？ It will take about 5 or 6 days to redo the insert, is that OK?
22.这个 产品的长 度为 330.12MM ,宽度为 78.96MM, 高度为 45MM.胶 厚为2MM, 重量为 70.63g, 试模注塑 机型号为 250吨,胶 料颜色为 黑色,产 品外表面 晒纹处 理,内表 2344氮 硬，斜顶 和行位座 用738H，
Can we add ejector sleeves or ejector pins in the boss of this part? 5． 产品 的这个位 置不能出 模，我们 打算做行 位，在此 面上会有 分模线， 你接受 吗？ There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK? 6． 产品 里面的这 个位置我 们打算做 斜顶或内 行位，有 问题吗？
11． 斜 顶与后面 的柱位空 间太小， 斜顶在运 动时会干 涉到柱 子，能移 动这个柱 子的位置 吗？ The angular lifter interfer es with the boss during ejection . Please consider changing the position of the boss. 12． 这 个筋骨位 胶厚太 溥，而且 高度偏 高，注塑 时很难填 充这个筋 位，可以 增加这个 筋骨位的 厚度吗？
模具常用会话
1）这套模具资料都清楚了吗？1. 是的，这套模具资料很清楚了；2. 没有，我还有些地方需要和你再确认一下；3. 现在，我们有基本的信息，例如：模穴数，产品材料，注塑机资料和模具材料等，但我们还没有标准件的标准，浇口要求和产品表面要求。
1) Is everything clear on this mould? ( Any question on this mould? )-- Yes, everything is clear.-- No, I need to confirm some questions with you.-- Now, we have the basic information, such as: cavity number, product material, moulding machine specifications and steel information etc. But we do not have the standard of spare parts, gate requirements and the surface requirement of the part.2）这个产品有没有问题？1. 没有问题，客户很专业；2. 我检查到了以下问题：A. 除了骨位以外，大部分都加了拨模角。
它不会影响模具结构；B. 没加拨模角。
我没有办法确认产品的分型面和模具结构。
2)Any question on this product?No. Our customer is very professional.I found the following problems after checking it:A. The draft angle is almost added except for some ribs. It will not affect the mould structure.B. No draft angle on the part. We can not confirm the parting line and the mould construction.3）模具有没有薄钢位？1.有，这里就有薄钢位, 模具强度会受影响；2.我仔细检查了产品的3D图，没有看到薄钢位，我如果以后发现了，我会立即告诉你。
最全模具英语(超级实用)
22. 这个 产品 的长 度为 330. 12MM ,宽 度为 78.9 6MM, 高度 为 45MM .胶 厚为 2MM, 重量
The leng th of this part is 330. 12MM , Widt h is 78.9 6MM, heig ht is 45MM
23． 现在 到了 吃午 钣的 时 间， 我们 下午 再继 续好 吗？
text ure by outreso urci ng, so we sugg est usin g the text ure by EDM
17． 模具 是用 公制 /英 制的 配 件？ 需要 备用 件 吗？
Is this mold dime nsio n meas ured in inch es or mete rs? Does it need spar
10． 产品 的这 个位 置太 小， 导致 模具 钢料 太 溥， 能够 加宽 这个 位置 吗？
This posi tion is too smal l and will make the stee l mate rial here too thin
11． 斜顶 与后 面的 柱位 空间 太 小， 斜顶 在运 动时 会干 涉到 柱 子， 能移 动这 个柱
39. P.L 面開 在此 處， 模具 上會 有尖 角和 刀 口， 對模 具壽 命有 影響
(The re are shar p edge s if we set the part ing line here , It will redu ce
40. 加大 拔模 角， 以便 脫模 順利 We sugg est enla rgin g the draf t angl e to
32. 此處 做斜 銷在 作動 時會 削到 成品 肉厚
模具常用英语对话
模具常用英语对话1．XXX！你现在有空吗，我可以问你一些问题吗？Could I ask you some questions if you are free? / Are you free now? May I ask you some questions (a question)?2．请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its surface? Texture or Polishing ?3．请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗？Does this part need an ejector pin or an ejector bar? Can we add an ejector blade?4．这个产品的柱位我们打算做司筒。
（或镶针）可以吗？Can we add ejector sleeves or ejector pins in the boss of this part?5．产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK?6．产品里面的这个位置我们打算做斜顶或内行位，有问题吗？We will make the lifter and (inner) slider in this position, will that be a problem?7．你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？The 2D and 3D drawing you provided is not the same, can you tell me which one iscorrect?8．你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问题我们可以自己修改吗？修改后会给交给你确认。
关于设计招聘岗位的英语对话范文,三个人
关于设计招聘岗位的英语对话范文,三个人全文共10篇示例，供读者参考篇1Lucy: Hi guys! I heard our teacher say that we need to design a recruitment post for our school's upcoming art club. Let's brainstorm together on what we should include in the post!Tom: Yeah, that sounds fun! I think we should start by writing about what the art club is all about. We can say that it's a place for students who love drawing, painting, and creating things to come together and have fun.Amy: That sounds good, Tom! We can also mention that the art club will have different activities like painting classes, craft workshops, and even an art exhibition at the end of the year.Lucy: I think we should also write about the qualities we are looking for in new members. Like, they should be creative, passionate about art, and willing to learn new things.Tom: We should definitely include information about how students can sign up for the art club. Maybe we can have asign-up sheet in the school office or they can talk to one of the club members to join.Amy: And we should also mention the benefits of joining the art club, like making new friends who share the same interests, getting to showcase their artwork, and improving their artistic skills.Lucy: Great ideas, guys! Let's put all of this together and show it to our teacher. I think she will be really impressed with our recruitment post for the art club.Tom: I agree! This was a fun project to work on together. I can't wait to see all the new students who will join the art club because of our awesome post!Amy: Yeah, me too! I'm so proud of us for coming up with such a great recruitment post. I know the art club is going to be a big hit this year!篇2Title: Designing a Job PositionAmy: Hey guys, do you want to help me design a new job position for our company?Sam: Sure, that sounds like fun! What kind of job are we going to create?Danny: Yeah, I'm excited to come up with some cool ideas. Let's get started!Amy: Ok, so I think we should start by thinking about what skills and qualifications the person will need for this job.Sam: How about someone who is creative and good at coming up with new ideas?Danny: Yeah, and they should also be good at using design software like Adobe Illustrator and Photoshop.Amy: Great ideas, guys! I also think it would be important for this person to have good communication skills, so they can work well with the rest of the team.Sam: Definitely! We want someone who can listen to feedback and collaborate with others to come up with the best designs.Danny: I agree. And maybe we should also include some responsibilities in the job description, like meeting deadlines and presenting their work to clients.Amy: Good point, Danny. We want to make sure that the person we hire is reliable and can handle the pressure of afast-paced work environment.Sam: This is going to be a cool job position! I can't wait to see who we hire for it.Danny: Me too! I think we did a great job designing it together.Amy: Thanks for your help, guys. I think we make a great team!Sam and Danny: No problem, Amy. We're happy to help.篇3Title: Designing a Job PostCharacters: Sarah, Tim, and EmmaSarah: Hey Tim and Emma, our teacher asked us to come up with a job post for a designer position. Do you guys want to help me brainstorm some ideas?Tim: Sure! That sounds like fun. Let's think about what kind of skills and qualifications the designer should have.Emma: Yeah, definitely. I think the designer should have a good eye for art and be able to use design software like Photoshop and Illustrator.Sarah: That's a great point, Emma. They should also be creative and be able to come up with new and unique ideas for designs.Tim: I agree. It would be good if they have some experience with different design styles and techniques too.Emma: And don't forget about communication skills! The designer will need to be able to work with clients and understand their needs.Sarah: You're right, Emma. It's important for them to be able to communicate their ideas effectively and listen to feedback from others.Tim: I think we've got some good ideas here. Let's put them all together and create a job post that highlights all these qualities and skills.Emma: Sounds good to me! I think we've come up with a pretty solid job post for a designer position.Sarah: Great job, guys! I can't wait to show our teacher what we've come up with. Thanks for all your help!(All three high-five and walk off together, feeling proud of their collaborative effort)篇4Title: The Design Job InterviewCharacters:Tom: The interviewerAlice: The candidateBen: The company ownerTom: Hi Alice, thanks for coming in for the interview. Let's get started. Can you tell us a little bit about yourself and why you're interested in this design position?Alice: Hi, Tom. I'm Alice and I love drawing and creating things. I think this job is perfect for me because I can use my creativity to make cool designs for the company.Tom: That's great to hear! We're looking for someone who can think outside the box and come up with innovative ideas. Can you tell us about a project you worked on that you're proud of?Alice: Sure! I once designed a poster for a school event and everyone loved it. I used bright colors and fun fonts to make it stand out. It was a lot of fun to work on.Tom: That's fantastic, Alice. We're impressed with your work. Now, let's talk about your skills. What programs are you familiar with for design work?Alice: I'm good at using Adobe Illustrator and Photoshop. I also know how to use Canva and Sketch. I like trying out new programs to see what works best for each project.Tom: That's great to hear. We use those programs here at the company, so you'll fit right in. Now, let's move on to the last question. Why do you think you're the best candidate for this position?Alice: I think I'm the best candidate because I have a passion for design and I'm always looking for ways to improve my skills. I'm a hard worker and I work well in a team. I think I can bring a lot of creativity to the company.Tom: Thank you, Alice. We'll be in touch soon with our decision. It was great meeting you.Later on, Ben, the company owner, reviews Alice's interview and is impressed with her skills and enthusiasm. He decides tooffer her the position and she happily accepts, excited to start her new job as a designer.篇5Three kids named Timmy, Cindy, and Jimmy are discussing about designing a recruitment post for their school's design club.Timmy: Hey guys, let's make a cool job post to recruit new members for the design club!Cindy: Yeah, that sounds like a great idea! What should we include in the post?Jimmy: How about we start by introducing the design club and what kind of projects we work on?Timmy: Ooh, good idea! We can talk about all the fun things we design, like posters, logos, and even animations!Cindy: And we should definitely mention that no experience is necessary to join. We can teach new members all the skills they need.Jimmy: Yeah, that's a great point! We want to make sure everyone feels welcome to join, no matter their level of experience.Timmy: Oh, and we should also include some testimonials from current members to show how much fun they're having in the design club.Cindy: I love that idea! It will help get more kids excited about joining and being part of our creative team.Jimmy: I think we have some awesome ideas for our job post! Let's put it all together and share it with our classmates.Timmy: Great plan, guys! I can't wait to see all the new recruits who will join our design club and help us create amazing projects together!篇6Title: Designing a Job OpeningCharacters: Jack, Emily, and SarahJack: Hey guys, I'm thinking about creating a job opening for a designer role at our company. What do you think?Emily: That's a great idea, Jack! We definitely need someone who can help us with all the cool designs for our products.Sarah: Yeah, I agree. But what exactly are we looking for in a designer? Do they need to have a specific skill set or experience?Jack: Good question, Sarah. I think we should look for someone who has a creative mind, is good at using design software like Photoshop and Illustrator, and has a good eye for detail.Emily: I also think it's important to find someone who can work well in a team and can take feedback constructively. We want someone who can collaborate with us and bring fresh ideas to the table.Sarah: I agree with both of you. We should also look for someone who is passionate about design and is always looking for ways to improve their skills. Maybe we can even include a test project as part of the interview process to see their skills in action.Jack: That's a great idea, Sarah! Let's start drafting the job description and requirements, and then we can start spreading the word about the opening.Emily: I'm excited to see who we can find for this role. I think with the three of us working together, we can find the perfect designer to join our team.Sarah: I can't wait to see all the amazing designs they'll bring to the table. Let's get started on creating the job opening right away!Jack: Let's do this, team! I know we can find the perfect fit for our company.篇7Title: Designing a Job PostCharacters: Amy, Tom, and LilyAmy: Hey guys! I have an idea. Let’s design a job post for our school’s new art teacher!Tom: That sounds fun! What should we include in the job post?Lily: How about listing the qualifications needed for the job? Like having a degree in art and experience teaching kids.Amy: Good idea! We should also include information about the school and what the art teacher will be responsible for.Tom: Yeah, we can write about how our school values creativity and how the art teacher will lead art classes for different grade levels.Lily: What about the skills and qualities we want in the art teacher? Like being creative, patient, and able to inspire students.Amy: Definitely! We can also mention that the art teacher should be able to organize art exhibits and events for the school.Tom: Oh, and we should include information on how to apply for the job, like sending a resume and cover letter to the school.Lily: I think we’ve covered everything! Our job post is going to be so awesome.Amy: I can’t wait for our new art teacher to see it. I’m sure they’re going to love working at our school!Tom: Yeah, we did a great job desig ning this job post. I’m proud of us!(Laughter and high fives)End of conversationWord count: 216篇8Title: Designing a Job PostingCharacters: Amy, Lucy, and JackAmy: Hey, guys! I have an idea. Let's design a job posting for our new design department.Lucy: That sounds like a great idea! I bet we can come up with a really creative and eye-catching job posting.Jack: Yeah, I think it would be cool to attract some talented designers to join our team. Let's get started!Amy: Okay, so first we need to think about what skills and qualifications we want in a designer.Lucy: I think we should look for someone who is creative, detail-oriented, and has experience with different design software.Jack: And they should also have good communication skills and be able to work well in a team.Amy: Great ideas, guys! Now, let's think about how we can make our job posting stand out.Lucy: How about we use some bright colors and fun fonts to catch people's attention?Jack: Yeah, and we could include some examples of the type of work they would be doing to give them a sense of what the job entails.Amy: I love those ideas! Let's also make sure to highlight the benefits of working for our company, like flexible hours and opportunities for growth.Lucy: And we should include a contact email so they can easily apply for the position.Jack: This is going to be the best job posting ever! I can't wait to see all the talented designers who apply.Amy: Me too! I think we did a great job designing our job posting. Let's post it and start looking for our new team member!篇9Title: Designing a Job Position - Three Little DesignersLucy: Hey guys, have you heard about our school's design club creating a new job position?Tom: Yeah, I heard about it! They're looking for someone to help design posters and flyers for school events.Alice: That sounds like a cool job! I love drawing and designing stuff.Lucy: Me too! I think we should all apply for the position. Let's think of some ideas for our job interview.Tom: Good idea, Lucy! Maybe we can each come up with a design concept and present it during the interview.Alice: Yeah, that's a great idea! I can design a poster for the school talent show, with bright colors and fun illustrations.Tom: I can design a flyer for the sports carnival, with bold fonts and action-packed images.Lucy: And I can design a poster for the science fair, with scientific symbols and cool graphics. We each have our own unique style, so it will show the club how creative we are.Alice: I can't wait to show them our designs! I think we will all do great in the interview.Tom: Yeah, I agree! Let's go for it and show them what we've got. We're the best little designers in town!Lucy: Let's do this, guys! We'll rock the interview and land that job position for sure. Let's put our creative minds together and make our designs shine!(All three high-five each other and start working on their design concepts for the job interview)篇10Title: Designing Job PostingsLisa: Hey guys, have you ever thought about how to design job postings to attract more applicants?Ben: Oh yeah, I think it's important to make the job sound interesting so that more people would want to apply.Emily: I agree with Ben, but we also need to clearly state the job requirements and responsibilities so that applicants know what they are getting into.Lisa: That's right! Let's brainstorm some ideas on how to design a job posting for a graphic designer position.Ben: How about we start with a catchy title like "Join our creative team as a Graphic Designer"?Emily: I like that! We can then include a brief introduction about our company and what we do.Lisa: And we should definitely list out the specific responsibilities of the job, like creating graphics for social media,designing marketing materials, and collaborating with the marketing team.Ben: Yeah, and we should also mention the required skills and qualifications, like proficiency in Adobe Creative Suite and a degree in graphic design.Emily: I think it's also important to highlight any perks or benefits that come with the job, like flexible work hours or opportunities for professional development.Lisa: And we should end the job posting with a call to action, encouraging interested candidates to apply by a certain deadline.Ben: Great ideas, guys! I think with these tips, we can create a job posting that will attract top talent for our graphic designer position.Emily: Let's get started on drafting the job posting now!。
模具英语100句
模具英语100句如何用英文和老外检讨模具(2008-1-16 08:50)1．XXX！你现在有空吗，我可以问你一些问题吗？2．Could I ask you some questionsMay I ask you some questions (a question)2．请问此产品的面是否为外观面表面做什么处理是晒纹/抛光？Can you tell me whether the surface of this part is a visible/esthetic one What will we do for its surface T exture or Polishing3．请问产品这个面可否加顶针或顶块产品允许加扁顶针吗？Does this part need an ejector pin or an ejector bar Can we add an ejector blade4．这个产品的柱位我们打算做司筒。
（或镶针）可以吗？Can we add ejector sleeves or ejector pins in the boss of this part5．产品的这个位置有倒扣不能出模，我们打算做行位，在此面上会有分模线，你接受吗？There's an undercut at this position that can not be molded, we plan to make a slider for it. It will also have a parting line on this side, is that OK6．产品里面的这个位置我们打算做斜顶或内行位，有问题吗？We will make the lifter and (inner) slider in this position, will that be a problem7．你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？The 2D and 3D drawings you provided are not the same, could you advise which one is correct8．你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问题我们可以自己修改吗修改后会给交给你确认。
模具设计工程师面试自我介绍
模具设计工程师面试自我介绍英文回答：As a highly skilled and experienced mold design engineer with a proven track record of success in the manufacturing industry, I am confident that I possess the necessary knowledge, expertise, and abilities to excel in this role. Throughout my career, I have consistently exceeded expectations by designing and developing innovative and efficient mold solutions that have resulted in significant cost savings and increased productivity for my clients.My comprehensive understanding of mold design principles, coupled with my proficiency in utilizing industry-leading software such as CATIA, SolidWorks, and AutoCAD, enables me to create molds that meet precise specifications and deliver exceptional results. I am particularly adept at optimizing mold designs for various materials, including plastics, metals, and ceramics,ensuring optimal performance and longevity.Furthermore, my strong understanding of mold manufacturing processes, including injection molding, blow molding, and die casting, allows me to anticipate potential challenges and implement proactive measures to mitigate risks. I am highly proficient in mold flow analysis, which enables me to optimize mold designs for efficient material flow and minimize defects.Beyond my technical expertise, I am an effective communicator and a collaborative team player. I am adept at presenting complex technical concepts to both technical and non-technical audiences and can work seamlessly with cross-functional teams to ensure the successful execution of projects.I am eager to leverage my skills and experience to contribute to the success of your esteemed organization. I am confident that I can make a significant contribution to your mold design team and help drive innovation and excellence within your company.中文回答：作为一名技术娴熟、经验丰富的模具设计工程师，在制造业已取得成功，我确信自己具备胜任此职位所需的知识、专业知识和能力。
简单的模具工程师英语自我介绍
简单的模具工程师英语自我介绍Hello everyone,My name is [Your Name] and I am a mold engineer. I am excited to have the opportunity to introduce myself to you today.I have a strong passion for mold engineering and have been working in this field for [number of years] years. My expertise lies in designing and manufacturing both plastic and metal molds. I am knowledgeable in the latest industry standards and have experience working with various types of molds, such as injection molds and die casting molds.In my previous role at [Company Name], I was responsible for designing and developing molds for a range of products. I successfully collaborated with cross-functional teams, including design engineers and production managers, to ensure the molds met the required specifications and were delivered on time. I am confident in my ability to conceptualize and create efficient molds that improve manufacturing processes and product quality.I am also proficient in using CAD software, such as AutoCAD and SolidWorks, to create detailed mold designs. I am skilled in analyzing design specifications and identifying potential design flaws early on to minimize costly errors during production. Additionally, I am well-versed in conducting mold flow analysis and optimizing mold cooling systems to enhance productivity.I am a detail-oriented and result-driven individual with excellent problem-solving skills. I thrive in challenging environments andenjoy finding innovative solutions to complex mold engineering problems. I am constantly seeking opportunities to learn and grow in my field, and I believe in continuous professional development.In my free time, I enjoy staying up to date with the latest advancements in mold engineering by attending conferences and industry events. I also enjoy participating in online forums and discussions where I can exchange knowledge and ideas with fellow professionals.I am grateful for the chance to share a bit about myself with you today and look forward to learning more about each of you. Thank you for your time and attention.Sincerely,[Your Name]。
模具设计专业英语
/%E9%A2%84%E8%AE%A1%E4%BD%BF%E7%94%A8%E5%B9%B4%E9 %99%90Assembly line組裝線Layout布置圖Conveyer流水線物料板Rivet table拉釘機Rivet gun拉釘槍Screw driver起子Electric screw driver電動起子Pneumatic screw driver氣動起子worktable 工作桌OOBA開箱檢查fit together組裝在一起fasten鎖緊(螺絲)fixture 夾具(治具)pallet棧板barcode條碼barcode scanner條碼掃描器fuse together熔合fuse machine熱熔機repair修理operator作業員QC品管supervisor 課長ME制造工程師MT製造生技cosmetic inspect外觀檢查inner parts inspect內部檢查thumb screw大頭螺絲lbs.inch鎊、英寸EMI gasket導電條front plate前板rear plate后板chassis |'∫?si| 基座bezel panel面板power button電源按鍵reset button重置鍵Hi-pot test of SPS高源高壓測試V oltage switch of SPS電源電壓接柆鍵sheet metal parts 沖件plastic parts塑膠件SOP製造作業程序material check list物料檢查表work cell工作間trolley台車carton紙箱sub-line支線left fork叉車personnel resource department人力資源部production department生產部門planning department企劃部QC Section品管科stamping factory沖壓廠painting factory烤漆廠molding factory成型廠common equipment常用設備uncoiler and straightener整平機punching machine 沖床robot機械手hydraulic machine油壓機lathe車床planer |'plein?|刨床miller銑床grinder磨床driller鉆床linear cutting線切割electrical sparkle電火花welder電焊機staker=reviting machine鉚合機position職務president董事長general manager總經理special assistant manager特助factory director廠長department director部長deputy manager |'depjuti| =vice manager副理section supervisor課長deputy section supervisor =vice section superisor副課長group leader/supervisor組長line supervisor線長assistant manager助理to move, to carry, to handle搬運be put in storage入庫pack packing包裝to apply oil擦油to file burr 銼毛刺final inspection終檢to connect material接料to reverse material 翻料wet station沾濕台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|報廢scrape ..v.刮;削deficient purchase來料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮傷dents壓痕defective upsiding down抽芽不良defective to staking鉚合不良embeded lump|in'bed| |l?mp|鑲塊feeding is not in place送料不到位stamping-missing漏沖production capacity生產力education and training教育與訓練proposal improvement提案改善spare parts=buffer備件forklift叉車trailer=long vehicle拖板車compound die合模die locker鎖模器pressure plate=plate pinch壓板bolt螺栓name of a department部門名稱administration/general affairs dept總務部automatic screwdriver電動啟子thickness gauge厚薄規gauge(or jig)治具power wire電源線buzzle蜂鳴器defective product label不良標簽identifying sheet list標示單screwdriver holder起子插座pedal踩踏板stopper阻擋器flow board流水板hydraulic handjack油壓板車forklift叉車pallet棧板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger無名指little finger小指band-aid創可貼iudustrial alcohol工業酒精alcohol container沾濕台head of screwdriver起子頭sweeper掃把mop拖把vaccum cleaner吸塵器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain鏈條jack升降機production line流水線chain鏈條槽magnetizer加磁器lamp holder燈架to mop the floor拖地to clean the floor掃地to clean a table擦桌子air pipe 氣管packaging tool打包機packaging打包missing part漏件wrong part錯件excessive defects過多的缺陷critical defect極嚴重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合規格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外觀不良slipped screwhead/slippery screw head螺絲滑頭slipped screwhead/shippery screw thread滑手speckle斑點mildewed=moldy=mouldy發霉rust生銹deformation變形burr(金屬)flash(塑件)毛邊poor staking鉚合不良excesssive gap間隙過大grease/oil stains油污inclusion雜質painting peel off臟污shrinking/shrinkage縮水mixed color雜色scratch劃傷poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包帶折皺painting make-up補漆discoloration羿色water spots水漬polishing/surface processing表面處理exposed metal/bare metal金屬裸露lack of painting烤漆不到位safety安全quality品質delivery deadline交貨期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企劃QC品管die worker模工production, to produce生產equipment設備to start a press開機stop/switch off a press關機classification整理regulation整頓cleanness清掃conservation清潔culture教養qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste廢料board看板feeder送料機sliding rack滑料架defective product box不良品箱die change 換模to fix a die裝模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket膠筐isolating plate baffle plate; barricade隔板carton box紙箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines壓線to compress, compressing壓縮character die字模to feed, feeding送料transportation運輸(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料變更feature change 特性變更evaluation評估prepare for, make preparations for 準備parameters參數rotating speed, revolution轉速manufacture management製造管理abnormal handling異常處理production unit生產單位lots of production生產批量steel plate鋼板roll material捲料manufacture procedure制程operation procedure作業流程to revise, modify修訂to switch over to, switch---to throw--over switching over切換engineering, project difficulty工程瓶頸stage die工程模automation自動化to stake, staking, reviting鉚合add lubricating oil加潤滑油shut die架模shut height of a die架模高度analog-mode device類模器die lifter舉模器argon welding氬焊vocabulary for stamping衝壓常詞匯stamping, press沖壓punch press, dieing out press沖床uncoiler & strainghtener整平機feeder送料機rack, shelf, stack料架cylinder油缸robot機械手taker取料機conveyer belt輸送帶transmission rack輸送架top stop上死點bottom stop下死點one stroke一行程inch寸動to continue, cont.連動to grip(material)吸料location lump, locating piece, block stop 定位塊reset復位smoothly順利dent壓痕scratch刮傷deformation變形filings鐵削to draw holes抽孔inquiry, search for查尋to stock, storage, in stock庫存receive領取approval examine and verify審核processing, to process加工delivery, to deliver 交貨to return delivenry to. to send delinery back to retrn of goods退貨registration登記registration card登記卡to control管制to put forward and hand in提報safe stock安全庫存acceptance = receive驗收to notice通知application form for purchase請購單consume, consumption消耗to fill in填寫abrasion磨損reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics統計demand and supply需求career card履歷卡to take apart a die卸下模具to load a die裝上模具to tight a bolt擰緊螺栓to looser a bolt擰鬆螺栓to move away a die plate移走模板easily damaged parts易損件standard parts標準件breaking.(be)broken,(be)cracked 斷裂to lubricate潤滑common vocabulary for die engineering模具工程常用詞匯die 模具figure file, chart file圖檔cutting die, blanking die沖裁模progressive die, follow (-on)die連續模compound die復合模punched hole沖孔panel board鑲塊to cutedges=side cut=side scrap切邊to bending折彎to pull, to stretch拉伸Line streching, line pulling線拉伸engraving, to engrave刻印upsiding down edges翻邊to stake鉚合designing, to design設計design modification設計變化die block模塊folded block折彎塊sliding block滑塊location pin定位銷lifting pin頂料銷die plate, front board模板padding block墊塊stepping bar墊條upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上墊板spare dies模具備品spring 彈簧bolt螺栓document folder文件夾file folder資料夾to put file in order整理資料spare tools location手工備品倉first count初盤人first check初盤復櫂人second count 復盤人second check復盤復核人equipment設備waste materials廢料work in progress product在制品casing = containerazation裝箱quantity of physical invetory second count 復盤點數量quantity of customs count會計師盤,點數量the first page第一聯filed by accounting department for reference會計部存查end-user/using unit(department)使用單位summary of year-end physical inventory bills年終盤點截止單據匯總表bill name單據名稱This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表請與盤點清冊一起送會計部－(NHK廠區送財會部)Application status records of year-end physical inventory List and physical inventory card 年終盤點卡與清冊使用－狀況明細表blank and waste sheet NO.空白與作廢單號plate電鍍mold成型material for engineering mold testing工程試模材料not included in physical inventory不列入盤點sample樣品incoming material to be inspected進貨待驗description品名steel/rolled steel鋼材material statistics sheet物料統計明細表meeting minutes會議記錄meeting type 會別distribution department分發單位location地點chairman主席present members出席人員subject主題conclusion結論decision items決議事項responsible department負責單位pre-fixed finishing date預定完成日approved by / checked by / prepared by核準/審核/承辦PCE assembly production schedule sheetPCE組裝廠生產排配表model機鍾work order工令revision版次remark備注production control confirmation生產確認checked by初審approved by核準department部門stock age analysis sheet庫存貨齡分析表on-hand inventory現有庫存available material良品可使用obsolete material良品已呆滯to be inspected or reworked待驗或重工total合計cause description原因說明part number/ P/N 料號type形態item/group/class類別quality品質prepared by制表notes說明year-end physical inventory difference analysis sheet年終盤點差異分析表physical inventory盤點數量physical count quantity帳面數量difference quantity差異量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods處理品warehouse/hub倉庫on way location在途倉oversea location海外倉spare parts physical inventory list備品盤點清單spare molds location模具備品倉skid/pallet棧板tox machine自鉚機wire EDM線割EDM放電機coil stock卷料sheet stock片料tolerance工差score=groove壓線cam block滑塊pilot導正筒trim剪外邊pierce剪內邊drag form壓鍛差pocket for the punch head挂鉤槽slug hole廢料孔feature die公母模expansion dwg展開圖radius半徑shim(wedge)楔子torch-flame cut火焰切割set screw止付螺絲form block折刀stop pin定位銷round pierce punch=die button圓沖子shape punch=die insert異形子stock locater block定位塊under cut=scrap chopper清角active plate活動板baffle plate擋塊cover plate蓋板male die公模female die母模groove punch壓線沖子air-cushion eject-rod氣墊頂桿spring-box eject-plate彈簧箱頂板bushing block襯套insert 入塊club car高爾夫球車capability能力parameter參數factor系數phosphate皮膜化成viscosity涂料粘度alkalidipping脫脂main manifold主集流脈bezel斜視規blanking穿落模dejecting頂固模demagnetization去磁;消磁high-speed transmission高速傳遞heat dissipation熱傳rack上料degrease脫脂rinse水洗alkaline etch齡咬desmut剝黑膜D.I. rinse純水次Chromate鉻酸處理Anodize陽性處理seal封孔revision版次part number/P/N料號good products良品scraped products 报废品defective products 不良品finished products 成品disposed products 處理品barcode條碼flow chart流程表單assembly組裝stamping沖壓molding成型spare parts=buffer備品coordinate座標dismantle the die折模auxiliary fuction輔助功能poly-line多義線heater band 加熱片thermocouple熱電偶sand blasting噴沙grit 砂礫derusting machine除銹機degate打澆口dryer烘干機induction感應induction light感應光response=reaction=interaction感應ram連杆edge finder巡邊器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 銀紋gas mark焦痕delamination起鱗cold slug冷塊blush 導色gouge溝槽;鑿槽satin texture段面咬花witness line證示線patent專利grit沙礫granule=peuet=grain細粒grit maker抽粒機cushion緩沖magnalium鎂鋁合金magnesium鎂金metal plate鈑金lathe車mill銼plane鉋grind磨drill鋁boring鏜blinster氣泡fillet鑲;嵌邊through-hole form通孔形式voller pin formality滾針形式cam driver鍘楔shank摸柄crank shaft曲柄軸augular offset角度偏差velocity速度production tempo生產進度現狀torque扭矩spline=the multiple keys花鍵quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel鎢高速的moly high speed steel鉬高速的organic solvent有機溶劑bracket小磁導liaison聯絡單volatile揮發性resistance電阻ion離子titrator滴定儀beacon警示燈coolant冷卻液crusher破碎機模具工程類plain die簡易模pierce die沖孔模forming die成型模progressive die連續模gang dies複合模shearing die剪邊模riveting die鉚合模pierce沖孔forming成型(抽凸,沖凸)draw hole抽孔bending折彎trim切邊emboss凸點dome凸圓semi-shearing半剪stamp mark沖記號deburr or coin壓毛邊punch riveting沖壓鉚合side stretch側沖壓平reel stretch卷圓壓平groove壓線blanking下料stamp letter沖字(料號) shearing剪斷tick-mark nearside正面壓印tick-mark farside反面壓印沖壓名稱類extension dwg展開圖procedure dwg工程圖die structure dwg模具結構圖material材質material thickness料片厚度factor系數upward向上downward向下press specification沖床規格die height range適用模高die height閉模高度burr毛邊gap間隙weight重量total wt.總重量punch wt.上模重量五金零件類inner guiding post內導柱inner hexagon screw內六角螺釘dowel pin固定銷coil spring彈簧lifter pin頂料銷eq-height sleeves=spool等高套筒pin銷lifter guide pin浮升導料銷guide pin導正銷wire spring圓線彈簧outer guiding post外導柱stop screw止付螺絲located pin定位銷outer bush外導套模板類top plate上托板（頂板）top block上墊腳punch set上模座punch pad上墊板punch holder上夾板stripper pad脫料背板up stripper上脫料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下墊板die holder下夾板die set下模座bottom block下墊腳bottom plate下托板(底板)stripping plate內外打(脫料板)outer stripper外脫料板inner stripper內脫料板lower stripper下脫料板零件類punch沖頭insert入塊(嵌入件)deburring punch壓毛邊沖子groove punch壓線沖子stamped punch字模沖子round punch圓沖子special shape punch異形沖子bending block折刀roller滾軸baffle plate擋塊located block定位塊supporting block for location定位支承塊air cushion plate氣墊板air-cushion eject-rod氣墊頂桿trimming punch切邊沖子stiffening rib punch = stinger 加強筋衝子ribbon punch壓筋沖子reel-stretch punch卷圓壓平沖子guide plate定位板sliding block滑塊sliding dowel block滑塊固定塊active plate活動板lower sliding plate下滑塊板upper holder block上壓塊upper mid plate上中間板spring box彈簧箱spring-box eject-rod彈簧箱頂桿spring-box eject-plate彈簧箱頂板bushing bolck襯套cover plate蓋板guide pad導料塊塑件&模具相關英文compre sion molding壓縮成型flash mold溢流式模具plsitive mold擠壓式模具split mold分割式模具cavity型控母模core模心公模taper錐拔leather cloak倣皮革shiver飾紋flow mark流痕welding mark溶合痕post screw insert螺紋套筒埋值self tapping screw自攻螺絲striper plate脫料板piston活塞cylinder汽缸套chip細碎物handle mold手持式模具移轉成型用模具encapsulation molding低壓封裝成型射出成型用模具two plate兩極式（模具）well type蓄料井insulated runner絕緣澆道方式hot runner熱澆道runner plat澆道模塊valve gate閥門澆口band heater環帶狀的電熱器spindle閥針spear head鉋尖頭slag well冷料井cold slag冷料渣air vent排氣道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin頂出針knock pin頂出銷return pin回位銷反頂針sleave套筒stripper plate脫料板insert core放置入子runner stripper plate澆道脫料板guide pin導銷eject rod (bar)（成型機）頂業捧subzero深冷處理three plate三極式模具runner system澆道系統stress crack應力電裂orientation定向sprue gate射料澆口，直澆口nozzle射嘴sprue lock pin料頭鉤銷(拉料杆) slag well冷料井side gate側澆口edge gate側緣澆口tab gate搭接澆口film gate薄膜澆口flash gate閘門澆口slit gate縫隙澆口fan gate扇形澆口dish gate因盤形澆口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜澆口ring gate環形澆口subarine gate潛入式澆口tunnel gate隧道式澆口pin gate針點澆口Φ0.8~1.0mmRunner less無澆道(sprue less)無射料管方式long nozzle延長噴嘴方式sprue澆口;溶渣品質人員名稱類QC quality control 品質管理人員FQC final quality control 終點品質管制人員IPQC in process quality control 制程中的品質管制人員OQC output quality control 最終出貨品質管制人員IQC incoming quality control 進料品質管制人員TQC total quality control 全面質量管理POC passage quality control 段檢人員QA quality assurance 質量保證人員OQA output quality assurance 出貨質量保證人員QE quality engineering 品質工程人員品質保證類FAI first article inspection 新品首件檢查FAA first article assurance 首件確認TVR tool verification report 模具確認報告3B 3B 模具正式投產前確認CP capability index 能力指數CPK capability index of process 模具製程能力參數SSQA standardized supplier quality 合格供應商品質評估OOBA out of box audit 開箱檢查QFD quality function deployment 品質機能展開FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8項回復內容FA final audit 最後一次稽核CAR corrective action request 改正行動要求corrective action report 改正行動報告FQC運作類AQL Acceptable Quality Level 運作類允收品質水準S/S Sample size 抽樣檢驗樣本大小ACC Accept 允收REE Reject 拒收CR Critical 極嚴重的MAJ Major 主要的MIN Minor 輕微的AOQ A verage Output Quality 平均出廠品質AOQL A verage Output Quality Level 平均出廠品質Q/R/S Quality/Reliability/Service 品質/可靠度服務MIL-STD Military-Standard 軍用標準S I-S IV Special I-Special IV 特殊抽樣水準等級P/N Part Number 料號L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件檢查報告FPIR First Piece Inspection Report 百萬分之一PPM Percent Per Million 批號制程統計品管專類SPC Statistical Process Control 統計製程管制SQC Statistical Quality Control 統計品質管制R Range 全距AR A verary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重測性判斷量可靠與否DIM Dimension 尺寸DIA Diameter 直徑FREQ Frequency 頻率N Number 樣品數其它品質術語類QCC Quality Control Circle 品質圈QIT Quality Improvement Team 品質改善小組PDCA Plan Do Check Action 計劃執行檢查總結ZD Zero Defect 零缺點QI Quality Improvement 品質改善QP Quality Policy 目標方針TQM Total Quality Management 全面品質管理MRB Material Reject Bill 退貨單LQL Limiting Quality Level 最低品質水準RMA Return Material Audit 退料認可QAN Quality Amelionrate Notice 品質改善活動ADM Absolute Dimension Measuremat 全尺寸測量QT Quality Target 品質目標7QCTools 7 Quality Controll Tools 品管七大手法通用之件類ECN Engineering Change Notes 工程變更通知(供應商)ECO Engineering Change Order 工程改動要求(客戶)PCN Process Change Notice 工序改動通知PMP Product Management Plan 生產管制計劃SIP Specification In Process 製程檢驗規格SOP Standard Operation Procedure 製造作業規範IS Inspection Specification 成品檢驗規範BOM Bill Of Material 物料清單PS Package Specification 包裝規範SPEC Specification 規格DWG Drawing 圖面系統文件類QC Quality System 品質系統ES Engineering Standarization 工程標準CGOO China General PCE龍華廠文件H Huston (美國)休斯敦C Compaq (美國)康伯公司C China 中國大陸A Assembly 組裝(廠)S Stamping 沖壓(廠)P Painting 烤漆(廠)I Intel 英特爾公司T TAIW AN 臺灣IWS International Workman Standard 工藝標準ISO International Standard Organization 國際標準化組織GS General Specification 一般規格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq產品在龍華衝壓廠製造作業規範CQCA Q-Quality A-Assembly Compaq產品在龍華組裝廠品管作業規範CQCP P-Painting Compaq產品在龍華烤漆廠品管作業規範部類PMC Production & Material Control 生產和物料控制PPC Production Plan Control 生產計劃控制MC Material Control 物料控制ME Manafacture Engineering 製造工程部PE Project Engineering 產品工程部A/C Accountant Dept 會計部P/A Personal & Administration 人事行政部DC Document Center 資料中心QE Quality Engineering 品質工程(部)QA Quality Assurance 品質保證(處)QC Quality Control 品質管制(課)PD Product Department 生產部LAB Labratry 實驗室IE Industrial Engineering 工業工程R&D Research & Design 設計開發部P Painting 烤漆(廠)A Asssembly 組裝(廠)S Stamping 沖壓(廠)生產類PCS Pieces 個(根,塊等)PRS Pairs 雙(對等)CTN Carton 卡通箱PAL Pallet/skid 棧板PO Purchasing Order 采購訂單MO Manufacture Order 生產單D/C Date Code 生產日期碼ID/C Identification Code (供應商)識別碼SWR Special Work Request 特殊工作需求L/N Lot Number 批號P/N Part Number 料號其它OEM Original Equipment Manufacture 原設備製造PCE Personal Computer Enclosure 個人電腦外設PC Personal Computer 個人電腦CPU Central Processing Unit 中央處理器SECC SECC` 電解片SGCC SGCC 熱浸鍍鋅材料NHK North of Hongkong 中國大陸PRC People's Republic of China 中國大陸U.S.A the United States of America 美國A.S.A.P As Soon As Possible 盡可能快的E-MAIL Electrical-Mail 電子郵件N/A Not Applicable 不適用QTY Quantity 數量VS 以及REV Revision 版本JIT Just In Time 零庫存I/O Input/Output 輸入/輸出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 極嚴重不允許ESD Electry-static Discharge 靜電排放5S 希臘語整理,整頓,清掃,清潔,教養A TIN Attention 知會CC Carbon Copy 副本復印相關人員APP Approve 核準,認可,承認CHK Check 確認AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只讀光碟FDD Floppy Disk Drive 軟碟機HDD Hard Disk Drive 碟碟機REF Reference 僅供參考CONN Connector 連接器CA V Cavity 模穴CAD Computer Aid Design 計算機輔助設計ASS'Y Assembly 裝配,組裝MA T'S Material 材料IC Integrated Circuit 集成電路T/P True Position 真位度TYP Type 類型WDR Weekly Delivery Requitement 周出貨需求C?T Cycle Time 制程周期L/T Lead Time 前置時間(生產前準備時間)S/T Standard Time 標準時間P/M Product Market 產品市場3C Computer,Commumcation,Consumer electronic's 消費性電子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,財務,技術,時間(資源) SQA Strategy Quality Assurance 策略品質保證DQA Desigh Quality Assurance 設計品質保證MQA Manufacture Quality Assurance 製造品質保證SSQA Sales and service Quality Assurance 銷售及服務品質保證LRR Lot Rejeet Rate 批退率BS Brain storming 腦力激蕩EMI Electronic Magnetion Inspect 高磁測試FMI Frequency Modulatim Inspect 高頻測試B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 電源箱DT Desk Top 臥式(機箱)MT Mini-Tower 立式(機箱)DVD Digital V edio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先進的基本輸入/輸出系統CMOS Complemeruary Metoll Oxide Semiconductor 互補金屬氧化物半導體PDA Personal Digital Assistant 個人數字助理IC Integrated Circuit 集成電路ISA Industry Standard Architecture 工業標準體制結構MCA Micro Channel Architecture 微通道結構EISA Extended Industry Standard Architecture 擴充的工業標準結構SIMM Single in-line memory module 單項導通匯流組件DIMM Dual in-line Memory Module 雙項導通匯流組件LED Light-Emitting Diode 發光二級管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金屬線緒束集組件F/C Flat Calle 排線PCB Printed Circuit Board 印刷電路板CAR Correction Action Report 改善報告NG Not Good 不良WPR Weekly Delivery Requirement 周出貨要求PPM Parts Per Million 百萬分之一TPM Total Production Maintenance 全面生產保養MRP Material Requiremcnt Planning 物料需計劃OC Operation System 作業系統TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 電子音樂工業RFI Read Frequency Input 讀頻輸入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技術用語各種模具常用成形方式accurate die casting 精密壓鑄powder forming 粉末成形calendaring molding 壓延成形powder metal forging 粉末鍛造cold chamber die casting 冷式壓鑄precision forging 精密鍛造cold forging 冷鍛press forging 沖鍛compacting molding 粉末壓出成形rocking die forging 搖動鍛造compound molding 複合成形rotary forging 迴轉鍛造compression molding 壓縮成形rotational molding 離心成形dip mold 浸漬成形rubber molding 橡膠成形encapsulation molding 注入成形sand mold casting 砂模鑄造extrusion molding 擠出成形shell casting 殼模鑄造foam forming 发泡成形sinter forging 燒結鍛造forging roll 軋鍛six sides forging 六面鍛造gravity casting 重力鑄造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高壓鑄造hot chamber die casting 熱室壓鑄swaging 擠鍛hot forging 熱鍛transfer molding 轉送成形injection molding 射出成形warm forging 溫鍛investment casting 精密鑄造matched die method 對模成形法laminating method 被覆淋膜成形low pressure casting 低壓鑄造lost wax casting 脫蠟鑄造matched mould thermal forming 對模熱成形模各式模具分類用語bismuth mold 鉍鑄模landed plunger mold 有肩柱塞式模具burnishing die 擠光模landed positive mold 有肩全壓式模具button die 鑲入式圓形凹模loading shoe mold 料套式模具center-gated mold 中心澆口式模具loose detail mold 活零件模具chill mold 冷硬用鑄模loose mold 活動式模具clod hobbing 冷擠壓製模louvering die 百葉窗沖切模composite dies 複合模具manifold die 分歧管模具counter punch 反凸模modular mold 組合式模具double stack mold 雙層模具multi-cavity mold 多模穴模具electroformed mold 電鑄成形模multi-gate mold 複式澆口模具expander die 擴徑模offswt bending die 雙折冷彎模具extrusion die 擠出模palletizing die 疊層模family mold 反套製品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通氣性模具duplicated cavity plate 複板模positive mold 全壓式模具fantail die 扇尾形模具pressure die 壓緊模fishtail die 魚尾形模具profile die 輪廓模flash mold 溢料式模具progressive die 順序模gypsum mold 石膏鑄模protable mold 手提式模具hot-runner mold 熱流道模具prototype mold 雛形試驗模具ingot mold 鋼錠模punching die 落料模lancing die 切口模raising(embossing) 壓花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 無流道冷料模具sectional die 對合模具segment mold 組合模semi-positive mold 半全壓式模具shaper 定型模套single cavity mold 單腔模具solid forging die 整體鍛模split forging die 拼合鍛模split mold 雙併式模具sprueless mold 無注道殘料模具squeezing die 擠壓模stretch form die 拉伸成形模sweeping mold 平刮鑄模swing die 振動模具three plates mold 三片式模具trimming die 切邊模unit mold 單元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 軛型模模具廠常用之標準零配件air vent vale 通氣閥anchor pin 錨梢angular pin 角梢baffle 調節阻板angular pin 傾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑塊binder plate 壓板blank holder 防皺壓板blanking die 落料沖頭bolster 上下模板bottom board 澆注底板bolster 墊板bottom plate 下固定板bracket 扥架bumper block 緩衝塊buster 堵口casting ladle 澆注包casting lug 鑄耳cavity 模穴(模仁)cavity retainer plate 模穴扥板center pin 中心梢clamping block 鎖定塊coil spring 螺旋彈簧cold punched nut 冷沖螺母cooling spiral 螺旋冷卻栓core 心型core pin 心型梢cotter 開口梢cross 十字接頭cushion pin 緩衝梢diaphragm gate 盤形澆口die approach 模頭料道die bed 型底die block 塊形模體die body 鑄模座die bush 合模襯套die button 沖模母模die clamper 夾模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 沖模板die set 沖壓模座direct gate 直接澆口dog chuck 爪牙夾頭dowel 定位梢dowel hole 導套孔dowel pin 合模梢dozzle 輔助澆口dowel pin 定位梢draft 拔模錐度draw bead 張力調整桿drive bearing 傳動軸承ejection pad 頂出襯墊ejector 脫模器ejector guide pin 頂出導梢ejector leader busher 頂出導梢襯套ejector pad 頂出墊ejector pin 頂出梢ejector plate 頂出板ejector rod 頂出桿ejector sleeve 頂出襯套ejector valve 頂出閥eye bolt 環首螺栓filling core 椿入蕊film gate 薄膜形澆口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圓形模板fixed bolster plate 固定側模板flanged pin 帶凸緣销flash gate 毛邊形澆口flask 上箱floating punch 浮動沖頭gate 澆口gate land 澆口面gib 凹形拉緊销goose neck 鵝頸管guide bushing 引導襯套guide pin 導梢guide post 引導柱guide plate 導板guide rail 導軌head punch 頂镦沖頭headless punch 直柄沖頭heavily tapered solid 整體模蕊盒hose nippler 管接頭impact damper 緩衝器injection ram 壓射柱塞inlay busher 嵌入襯套inner plunger 內柱塞inner punch 內沖頭insert 嵌件insert pin 嵌件梢king pin 轉向梢king pin bush 主梢襯套knockout bar 脫模杵land 合模平坦面land area 合模面leader busher 導梢襯套lifting pin 起模頂销lining 內襯locating center punch 定位中心沖頭locating pilot pin 定位導梢locating ring 定位環lock block 壓塊locking block 定位塊locking plate 定位板loose bush 活動襯套making die 打印沖子manifold block 歧管檔塊master plate 靠模樣板match plate 分型板mold base 塑膠模座mold clamp 鑄模緊固夾mold platen 模用板moving bolster 換模保持裝置moving bolster plate 可動側模板one piece casting 整體鑄件parallel block 平行墊塊paring line 分模線parting lock set 合模定位器pass guide 穴型導板peened head punch 鑲入式沖頭pilot pin 導销pin gate 針尖澆口plate 襯板pre extrusion punch 頂擠沖頭punch 沖頭puncher 推桿pusher pin 襯套梢rack 機架rapping rod 起模桿re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮動脫模器ring gate 環型澆口roller 滾筒runner 流道runner ejector set 流道頂出器runner lock pin 流道拉梢screw plug 頭塞set screw 固定螺絲shedder 脫模裝置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺絲skeleton 骨架slag riser 冒渣口slide(slide core) 滑塊slip joint 滑配接頭spacer block 間隔塊spacer ring 間隔環spider 模蕊支架spindle 主軸sprue 注道sprue bushing 注道襯套sprue bushing guide 注道導套sprue lock bushing 注道定位襯套sprue puller 注道拉料销spue line 合模線square key 方鍵square nut 方螺帽square thread 方螺紋stop collar 限位套stop pin 止動梢stop ring 止動環stopper 定位停止梢straight pin 圓柱销stripper bolt 脫料螺栓stripper bushing 脫模襯套stripper plate 剝料板stroke end block 行程止梢submarine gate 潛入式澆口support pillar 支撐支柱/頂出支柱support pin 支撐梢supporting plate 扥板sweep templete 造模刮板tab gate 輔助澆口taper key 推拔鍵taper pin 拔錐梢/錐形梢teeming 澆注three start screw 三條螺紋thrust pin 推力銷tie bar 拉杵tunnel gate 隧道形澆口vent 通氣孔wortle plate 拉絲模板模具常用之工作機械。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
1）、这套模具资料都清楚了吗？1、是的，这套模具资料很清楚了；2、没有，我还有些地方需要和你再确认一下；3、现在，我们有基本的信息，例如：模穴数，产品材料，注塑机资料和模具材料等，但我们还没有标准件的标准，浇口要求和产品表面要求。
1) Is everything clear on this mould? ( Any question on this mould? )-- Yes, everything is clear.-- No, I need to confirm some questions with you.-- Now, we have the basic information, such as: cavity number, product material, moulding machine specifications and steel information etc. But we do not have the standard of spare parts, gate requirements and the surface requirement of the part.2）、这个产品有没有问题？1、没有问题，客户很专业；2、我检查到了以下问题：A.除了骨位以外，大部分都加了拨模角。
它不会影响模具结构；B.没加拨模角。
我没有办法确认产品的分型面和模具结构。
2) Any question on this product?-- No. Our customer is very professional.-- I found the following problems after checking it:A. The draft angle is almost added except for some ribs. It will not affect the mould structure.B. No draft angle on the part. We can not confirm the parting line and the mould construction.3）、模具有没有薄钢位？1、有，这里就有薄钢位, 模具强度会受影响；2、我仔细检查了产品的3D图，没有看到薄钢位，我如果以后发现了，我会立即告诉你。
3) Are there any weak steel (thin steel) areas on the mould?1. Yes, Here is weak steel. Mould strength will be effected.2. I have checked 3D part drawings carefully, no weak steel. I will let you know if I find it later.4）、注塑后，产品会不会有缩水现象？1、应当没有，产品壁厚挺均匀的，产品可能会有轻微缩水；2、这个产品设计的壁厚不均匀，特别是这些柱位和骨位太厚了，缩水痕很明显。
产品是外观件，我们强烈建议客户修改产品；4) After injection, will there be any sink marks on the part?1. Should not have. The wall thickness is even. The part might have slight sink marks.2. The part wall thickness is uneven, especially these ribs & bosses are too thick. The sink mark will be very visible. It is a cosmetic part. We strongly suggest customer to modify the part.5）、注塑后，产品会不会变形？1、应当不会变形，产品挺简单的；2、很有可能会变形。
产品又长又薄，很容易变形。
需告诉诉客户这事。
3、产品是平板件，很容易变形。
我们需要找到一个合适的浇口位置；5) Will there be any deformation on the part?1. No, the part is quite simple.2. Possible. The part is very long and thin, very easy to be deformed ( warpage). Please inform customer about this.3. The part is flat, easy to be deformed. We need to find a suitable gate location.6）、产品前后模方向你是如何考虑的？1、这很容易决定。
外观面前模出。
它不会粘前模;2、如果这边前模出，产品有30%机会粘前模。
我们需预留空间用于修改模。
3、我也是这么认为的。
不过，我们需做一些图片，与客户确认；6) How do you consider the direction of cavity & core?1. It is easy to decide that. The visible surface is cavity. It will not stick on the cavity side.2. If this side is cavity, the part has a 30% chance to stick to the cavity. We need to make extra room for future changes / modifications.3. I think so. But we need to make some pictures and confirm with customer.7）、你认为会不会粘行位或斜顶？1、模具结构挺简单的，应当不会；2、产品扣位处可能粘行位。
我们需考虑行位上加顶针；3、产品可能粘斜顶，所以我们需要考虑粘斜顶的部分如何分型。
7) Do you foresee sticking slide or angle lifter?1. No. The mould structure is simple.2. The undercut area may stick slide. We may consider to add an ejector pin on the slide.3. The part may stick on the angle lifter, so we need to consider the parting line for this area.8）、这是不是按最新版本产品图设计的？1、是啊，没错。
我们是是用最新版本产品图来更新模图的；2、我不太确定，我得检查一下，然后再告诉你，好吗？8) Is the design accordingly to the latest version of the part drawing?1. Yes. We revised the mould drawing accordingly to the latest part drawing.2. I am not sure. I will double check this (issue) and tell you later, ok?9）、这(塑胶料)的缩水是不是正确？1、是正确的，我查过了它的材料物性表；2、不太肯定。
这是客户提供的。
我会再查确认一下。
9) Is the shrinkage rate correct?1. Yes, I have double checked the moulding material specification.2. Not sure. It was provided by the customer. I will double check it.10）、模具是否和啤机相匹配？TIE BAR间距是多少？1、模具可以放得进客户要求的啤机。
法兰也是匹配的；2、我得检查一下它的唧嘴大小，顶棍孔位置以及顶杆螺牙类型是否正确。
10) Does the mould have a good fit with the moulding machine? What is the tie bar distance?1. Yes, it is no problem to put the mould into the specified moulding machine. The location ring has a good fit with the machine as well.2. I need to double check the sprue radius, the location of the KO hole, and the thread type of ejector rod.11）、模具能否全自动运行？1、产品和流道都可以自动掉下来；2、产品需机械手取出；3、产品可能会挂在斜顶上，需考虑二次顶出。
11) Does the mould run fully automatic?1. Yes, both the part and runner fall down fully automatically.2. No, the part need to be taken out by robot.3. The part may hang on the angle lifter, so we need to consider two stage ejection.。