焊接专业术语中英文对照表
焊接专业术语中英文对照整理
机械——焊接专业术语中英文对照（郭运）整理1Single 单面的2V—groove V型坡口3Joint 焊接接头4Edges overlap 接头形式5Butt 对接6T T型焊接7Fillet 角焊缝8Edge 端接9Corner 角接10Radius 半径11Joint root 焊接根部12Bevel angle 削边角度13Groove angle 坡口角度14Root face 根部钝边15Groove face 坡口面16Plug weld 塞焊17Spot weld 点焊18Seam weld 缝焊19Slot weld 槽焊20Double—flare—bevel—groove K型坡口焊缝21Single—flare—V 单面V型22Edge flange 翻边端接23Corner flange 卷边端接24Flange weld 卷边焊缝25Flare weld 扩口焊缝26Fillet weld 角焊缝27Slot weld 槽焊缝28Spot weld 点焊缝29Surfacing weld 堆焊焊缝30Melt—through weld 熔透焊缝31Backing weld 打底焊缝32Back weld 背面焊缝33Root weld 根部焊缝34Crown weld 隆起部分35Weld reinforcement 焊缝加强36Weld face 焊缝表面37Cap pass 盖面焊道38Weld edge 焊缝边缘39Leg 焊脚40Toe 焊趾41Buildup 堆焊42Weld reinforcement 焊缝加强高43Effective throat 有效焊喉44Concave weld 凹形焊缝45Convex weld 凸形焊缝46Unequal leg fillet 不等脚角焊47Oversize weld 大尺寸焊缝48Depth of fusion 熔合深度49Depth of penetration 熔透深度50Root penetration 根部熔深51Joint penetration 接头熔深52Weld interface 焊缝分界面53Diameter of weld at point of contact 焊缝在接触点上的直径54Thickness 厚度55Tail 尾部56Arrow 箭头57Reference line 参考线58Arrow side 箭头一边59Weld symbol 焊缝符号60Near side 近侧61Arrow side 箭头侧62Far side 远侧63Other side 另一侧64Put the weld on either—side 在任意一侧施焊65There is no side significance 没有方向区别66Edge flange 双卷边67Corner flange 单卷边68Weld size 焊缝尺寸69Effective throat 有效厚度70Root opening 根部间隙71Full penetration double bevel—groove weld K形坡口全焊透焊缝72Full penetration double V—groove weld 双V形坡口全焊透焊缝73Partial penetration double bevel—groove weld K形坡口部分焊透焊缝74Partial penetration double V—groove weld 双V形坡口部分焊透焊缝75Bevel groove 削边坡口76Flare groove 喇叭形坡口77Flange groove 卷边坡口78V—groove V形坡口79Staggered intermittent fillet weld 交错间断角焊缝80Chain intermittent fillet weld 链状间断角焊缝81Segmented fillet weld 分段角焊缝82Pitch distance 间距83Depth of filling 填充深度84Slot weld width 槽焊缝宽度85Plug weld diameter 塞焊缝的直径86Angle of countersink 深孔角度87A dimension to the right of the symbol 在符号右边的尺寸88A dimension of the required suggest diameter 所要求的直径尺寸89A value for the required shear strength per spot 每点所要求的剪切强度值90Spot weld size 点焊缝尺寸91Spot weld length 点焊缝的长度92Number of spot required 所要求的点的数量93Pitch distance between adjacent spots 两个相邻点的间距94Reference line 参考线95Melt—through of weld from other side 焊缝在另一侧熔透96Single bevel—groove weld with backing weld 加垫板的单边坡口焊缝97Single bevel—groove weld with back weld 背面焊的单边坡口焊缝98Single bevel—groove weld with backing weld 带垫板的V 形坡口焊缝99Single bevel—groove weld with back weld背面焊的V形坡口焊缝100Square groove 直边坡口101Skewed groove 斜坡口102Sloped groove 倾斜坡口103Scarf 斜嵌接104Gas metal arc spot weld 气体保护点焊105Resistance spot weld 电阻点焊106Gas metal arc seam weld 气体保护滚焊缝107Resistance seam weld 电阻滚焊缝108Gas metal arc slot weld 气体保护槽焊缝109The type of electrode to use 所要求焊条形式110The weld quality standard 焊缝质量标准111The weld procedure to use 所用的焊接程序112Codes 规范113Drawing 图纸114Specifications 技术要求115Contracts 合同116General 一般注解117Local 局部注解118The point for lifting an object 吊装一物体的点119Filler metals 填充金属120Pressure vessel fabrication 压力容器制造121Be as simple as possible 尽可能简单122Welder 焊工123Code body 规范本身124Shielded metal arc 手工电弧焊125Submerged arc 埋弧焊126Face bend 面弯127Root bend 背弯128Side bend 侧弯129Nick break 缺口破坏130Tensile 拉伸131Monitoring production welding 监视生产中的焊接132Strength 强度133Toughness 韧性134Hardness 硬度135Ductility 延展性136Compressive 压缩137Impact 冲击138Fatigue 疲劳139Undercut 咬边140Overlap 焊瘤141Cracking 裂纹142Porosity 气孔143Ultimate tensile strength 极限拉伸强度144Percent elongation 延伸率145Percent reduction of area 断面收缩率146Impact strength 冲击强度147Yield strength 屈服强度148Brinell 布氏149Vickers 韦氏150Rockwell 洛氏151Knoop 努氏152Fatigue test 疲劳试验153Tensile test 拉伸试验154Micro--hardness test 显微硬度试验155Charpy impact test 夏比冲击试验156Soundness test 致密性测试157Fillet break 角焊缝断裂158Metallographic 金相159Transverse fillet weld shear test 横向角焊缝剪切试验160Quality of the fractured weld 焊缝端口的质量161Ductility of the weld metal 焊缝金属的延展性162Impact strength of the weld 焊缝的冲击强度163Tensile strength of the base metal 母材的拉伸强度164Weld—ability 可焊性165Scratches caused by improper handling 由不适当的处理导致的划痕166Incomplete fusion 未熔合167Distortion 变形168Slag inclusions 夹渣169Vibratory stress relief 振动消除应力170External restraint 外部拘束171Thermal stress relief 热消除应力172Peening 锤击173Annealing 退火174Quenching 淬火175Tempering 回火176Normalizing 正火177Decrease current 降低电流178Decrease voltage 降低电压179Increase travel speed 加快焊接速度180Change from weave to stringer bead technique 从横向摆动焊道改成直线焊道技术181Result in a wider heat—affected zone hardness导致热影响区更宽182Produce a lower heat—affected zone hardness 降低热影响区硬度183Slow down the cooling rate 降低冷却速度184Reduce the tendency to produce martensite in the heat—affected zone 减少在热影响区形成马氏体的倾向185Stress relief 消除应力186Crater crack 弧坑裂纹187SMAW 手动电弧焊188PAW 等离子焊189FCAW 药芯焊190SAW 埋弧焊191Underfill 未焊满192Excess convexity 太凸193Excess weld reinforcement 焊缝余高太高194Overfill 过充195Scratch start 擦伤196Arc strike 引弧烧伤197Tungsten inclusion 夹钨198Lamination 分层199Lamellar tear 片状撕裂200Seam 划伤201Pipe shrinkage 缩孔202Longitudinal crack 纵向裂纹203Transverse crack 横向裂纹204Underbead crack 焊道中裂纹205Toe crack 焊趾裂纹206Root crack 根部裂纹207Base metal crack 母材裂纹208Before welding 焊接前209During welding 焊接时210After welding 焊接后211Waiting time 等待时间212Penetrating time 渗透时间213Soak time 吸入时间214Dwell time 驻留时间215AC 交流电216DC 直流电217DCEP 直流反接218。
常用焊接术语中英文对照
常用焊接术语中英文对照焊接Welding10.1 焊接种类Varieties of Welding电弧焊arc welding电熔焊electric fusion welding (EFW)气熔焊fusion gas welding (FGW)电阻焊electric resistance welding (ERW)有保护的金属电弧焊shielded metal arc welding (SMAW)手工或自动隋性气体保护钨极电弧焊manual and automatic inert gas tungsten arc welding (GTAW)自动埋弧焊automatic submerged arc welding金属极隋性气体保护电弧焊gas metal arc weiding (GMAW)氩弧焊argon-arc welding，气体保护电弧焊gas-shielded arc welding气焊gas welding; flame welding等离子焊plasma welding硬钎焊braze welding电渣焊electroslag welding爆炸焊explosive welding10.2 焊接形式Type of Welding角焊fillet welding间断焊intermittent welding点焊spot welding对焊butt welding搭焊lap welding塞焊plug welding珠焊bead welding槽焊slot welding堆焊build up welding垫板焊backing weld坡口grooveV形坡口V groove单面U形坡口single U grooveK形坡口double bevel grooveX形坡口double V groove双面U形坡口double U grooveU-V组合坡口combination U and V groove根部间隙root gap焊接符号symbol of weld错边量alignment tolerance10.3 焊接位置Welding Position仰焊overhead welding现场焊field weld (F.W.)封底焊back run welding立焊vertical welding平焊flat welding工厂（车间）焊接shop weld定位焊tack weld跳焊skip welding节距pitch10.4 焊接缺陷Defects of Welding焊接裂纹weld crack根部裂纹root crack微裂纹micro crack错位mismatch弧坑pit; crater焊穿burn through夹渣slag inclusion咬边；咬肉undercut焊瘤overlap气孔porosity, blow hole砂眼blister针孔pin hole严重飞溅excessive spatter未溶合incomplete fusion; lack of fusion 根部未焊透incomplete penetration10.5 其它母材；基层金属base metal预热preheating热影响区heat affected zone (HAZ)焊条welding electrode (rod)焊丝welding wire焊药（剂）flux。
常用的焊接名词中英文对照表
7
焊接工艺
Welding Technology (Welding Procedure)
8
焊接操作
Welding Operation
9
焊接顺序
Welding Sequence
10
熔敷顺序
Build-up Sequence
11
焊接方向
Direction of Welding
12
焊接位置
Position of Welding
常用的焊接名词中英文对照表
注：圆括号内为同义词，方括号内为可省略。
序号
焊接名词（中文）
焊接名词（英文）
1
焊接
Welding
2
熔焊
Fusion Welding
3
压焊
Pressure Welding
4
钎焊
Brazing and Soldering
5
焊接过程
Welding Process
6
焊接技术
Welding Technique
55
焊后热处理
Postweld Heat Treatment
56
预热温度
Preheat Temperature
57
后热温度
Postheating Temperature
58
层间温度
Interpass Temperature
59
焊丝伸出长度
Wire Extention
60
弧长
Arc Length
61
熔化速度
13
焊缝倾角
Weld Slope (Inclination of Weld Axis)
14
焊接专业词汇英汉对照
焊接常用词语英汉对照actual weld-throat thick-ness焊缝厚度all-around weld整周焊缝all-around weld (整周焊缝)环焊缝angle butt weld斜对接焊angle weld角焊appearance of weld焊缝成形arc-seam weld电弧缝焊arc-spot weld电弧点焊arc-weld电弧焊aspect ratio of weld焊缝成形系数at weld edge在焊缝边上attachment weld连接焊缝automatic spot weld自动点焊法automatic weld自动焊接axis of a weld焊缝中心线; 焊接轴线axis of weld焊缝轴线; 焊接轴线back of weld焊缝背面backing groove of weld焊缝反面坡口backing weld底焊; 底焊焊缝bare metal arc weld裸焊条电弧焊bead weld珠焊; 堆焊bead-on-plate weld堆焊焊缝beading weld凸焊beam-to-beam weld梁间焊接; 梁式引线焊接block sequence weld分段多层焊bond weld钢轨接头焊接bridge seam weld桥缝焊接; 桥线焊brize weld硬焊butt weld对接焊缝butt weld ends对头焊接端butt-weld碰焊; 平式焊接; 对头焊接butt-weld in the downhand position对接平焊butt-weld joint对头焊接butt-weld pipe mill对焊管轧机button spot weld按电钮点焊cap weld最后焊层; 盖面焊缝carbon content of weld materials焊接材料的碳含量cast-weld construction铸焊结构caulk weld填缝焊caulking weld密实焊缝chain intermittent fillet weld链式分段角焊; 并列间断角焊缝chain intermittent weld并列焊接circular weld环形焊缝circumferential weld环缝; 环焊缝cleft weld裂口焊closed weld底边无缝焊; 无间隙焊缝closed-chamber fusion weld闭室熔焊cluster weld丛聚焊缝coil weld卷板对接焊; 卷板对接焊; 板卷焊cold weld冷压接commutator-controlled weld换向控制焊接complete penetration butt weld贯穿对焊composite weld紧密焊缝; 强度密封焊缝concave filled weld凹形角焊缝concave filler weld凹角焊concave fillet weld凹面填角焊concave weld凹焊缝; 凹面焊; 凹形焊缝; 轻型焊connective weld联系焊缝continuous butt-weld mill连续式炉焊管机组continuous fillet weld连续(填)角焊缝; 连续角焊缝; 连续贴角焊continuous weld连续焊缝continuous weld process连续式炉焊管法contour weld特形焊接convex fillet weld凸角焊缝; 凸形角焊缝convex weld凸焊缝; 凸形焊缝copper weld wire包铜钢丝corner flange weld单卷边角焊缝corner weld角焊corner-flange weld卷边角焊缝; 卷边角焊缝crack of weld焊部裂纹cross weld十字交叉焊缝; 横向焊缝cross-wire weld十字焊crotch weld楔接锻接; 楔接焊接cup weld带盖板焊缝depth of weld焊接深度dissimilar weld metal不同的焊接金属; 不同金属的焊接distance between the toes of a weld焊缝宽度double groove weld双面坡口焊缝double-bevel groove weld双斜边坡口焊缝; 双斜坡口焊double-flanged butt weld双弯边对接焊缝double-V groove weld双斜边坡口焊缝; 双斜坡口焊downhand weld平焊缝duplex spot weld双点点焊接头edge joint weld边缘焊edge weld端接焊; 端接焊缝; 端面焊缝; 对边焊electric resistance weld mill电阻焊管机electric weld-pipe mill电焊管机electric-weld pipe mill电焊管机emporary weld临时点定焊缝excess weld metal焊缝补强金属; 补强; 补强焊料; 补强金属excess weld metal(焊缝的)余高explosive weld爆炸焊接face of weld焊缝表面; 焊接面fibrous weld纤维状焊缝field weld现场焊接filler weld填角焊缝fillet weld角焊缝; 填角焊; 贴角焊fillet weld in normal shear (搭接接头的)正面角焊缝fillet weld in parallel shear侧面角焊缝; 侧面填角焊fillet weld in the flat position角接平焊; 水平角焊缝fillet weld in the horizontal position横向角焊缝fillet weld size焊角尺寸; 填角焊缝尺寸flame weld火焰焊接flange weld卷边焊缝; 卷边焊缝flange-to-web weld卷边焊缝; 卷边焊缝flanged butt weld弯边对接焊flanged edge weld卷边焊; 卷边焊flash butt weld闪光焊flash weld闪速对焊flat faced fillet weld平顶角焊缝焊接flat fillet weld平角焊ing of fillet weld角焊缝平焊; 船形角焊flush fillet weld平角焊flush weld削平补强的焊缝; 平焊接; 无加强高的焊缝forge weld锻焊焊缝forged weld (焊后锻压的)锻压焊缝form factor of the weld焊缝成形系数formation of weld焊缝成形front fillet weld正侧面填角焊缝; 正面填角焊front(al) fillet weld正面角焊缝full fillet weld满角焊缝; 全角焊full penetration butt weld满对接焊full weld满焊full-fillet weld满角焊full-sized weld全尺寸焊缝full-strength weld (与母材等强)等强焊缝gap weld特殊点焊; 双极单点焊gas-pressure weld气压焊girth weld环形焊缝gravity weld倚焊groove weld坡口焊; 坡口焊缝; 有坡口焊缝; 凹槽焊groove-weld joint有坡口焊接接头hammer weld锻焊hand weld手焊焊缝height of reinforcement of weld加强焊缝高度helical-weld pipe螺旋焊管high performance weld flux高性能焊剂horizontal fillet weld横向角缝焊接horizontal weld横向焊缝horizontal-vertical fillet weld横向垂直角焊缝hot weld encapsulation热焊封袋hydraulic automatic weld液压自动焊接hydraulic weld process液压焊接法inclined weld斜焊inconel weld单面焊缝incorrect weld profile焊缝形状不对incorrect weld size焊缝尺寸不对induction weld mill感应焊管机inside corner weld内角焊接inside fillet weld内角焊接inside weld内焊缝insufficient or excess reinforcement of weld加强焊缝不足或过量intermittent fillet weld间断角缝焊接; 断续角焊缝intermittent weld断续焊; 断续焊缝jam weld对接焊; 对头焊接lap fillet weld搭接角焊缝laser (beam) weld (ing)激光焊lateral weld侧焊; 侧面焊缝leg of a fillet weld角焊缝; 角焊缝焊脚leg of fillet weld圆角焊肉厚length of weld焊缝长度light closing weld轻连续焊接light fillet weld轻型填角焊; 小填角焊light weld轻焊缝Lincoln weld埋弧自动焊longitudinal fillet weld纵向角焊longitudinal weld纵向焊缝longitudinal weld (焊接用语)纵缝loose weld脱焊main weld主焊缝mash seam weld压薄缝焊; 滚压焊mash weld点焊; 点压焊melt thru weld熔透焊缝melt-through weld透溶焊melten weld pool焊接熔池melting through weld熔透焊缝miter weld平顶角焊缝; 斜接角焊缝molten weld metal熔融焊接金属mulitple impulse weld多脉冲焊缝multilayer weld多层焊缝multipass weld多道焊缝multiple arc weld多弧焊缝multiple-electrode submerged arc weld多电极埋弧焊multiple-pass weld多道焊缝; 多路焊接multirun weld多道焊缝nonpressure thermit weld不加压热剂焊缝normal weld正常焊接oblique fillet weld斜交角焊缝; 斜角焊接one-pass weld单层焊缝open butt weld开口对接焊open weld留间隙焊缝; 空隙焊outside weld外焊缝over weld过焊overhead fillet weld仰焊角焊缝overhead weld仰焊oversize weld超尺寸焊缝oxygen weld氧气焊接parallel-arc weld并列弧焊patch weld补焊; 补孔焊缝Peltier's cross weld珀耳帖交叉焊接penetration weld熔透焊缝percussion weld冲击焊缝; 冲击焊接periphera weld环形焊缝pitch of weld焊缝接距; 焊线距plain butt weld无坡口对接焊; 平头对接焊缝plasma-arc weld等离子弧焊接plug weld塞焊焊缝point of weld焊接点point weld点焊poor weld劣质焊缝; 有缺陷的焊缝porous weld多孔焊缝; 疏松焊缝positioned weld平位焊缝; 暂焊post weld annealed (PWA)焊后退火poured weld铸焊焊缝powder weld process粉末焊接法practice weld试验焊缝pressure weld压焊pressure-controlled weld压力控制焊接pressure-tight weld气密焊; 密封焊道principal weld主要焊缝profile of fillet weld填角焊缝轮廓progress of weld焊向projection weld凸焊; 凸焊焊缝projection weld machine凸点电阻焊机pulsating weld脉冲接触焊push weld挤焊quilting weld钉焊reinforced butt weld补强的对接焊缝; 补强式对接焊缝reinforced weld加强焊接reinforcement of weld焊缝加厚; 补强金属; 加强焊缝resistance weld mill电阻焊管机resistance weld pipe电阻焊管resonance butt weld谐振式对接焊restarting a weld再引弧ripple weld鳞状焊缝rivet weld电铆; 电铆焊缝root face of weld焊缝根部钝边root gap of weld焊缝根部间隙root of weld焊缝根部; 焊根root opening of weld焊缝根部间隙root radius of weld焊缝坡口根部半径sagged weld下垂焊缝scarf weld楔口焊接seal weld填焊; 致密焊缝; 密封焊; 密封焊道; 密封焊缝sealing weld封焊seam weld滚焊semi-automatic arc weld半自动电弧焊sequence weld timer序列焊接时间调节器shallow weld浅焊shop weld工厂焊接shot weld点焊shoulder of weld焊缝根部钝边side fillet weld侧面角焊缝; 侧面填角焊缝; 侧面贴角焊side lap weld侧边搭接焊; 弯边搭焊缝side weld侧焊缝; 边焊single lap weld单搭接焊single strap butt weld单面盖板对接焊single-bevel groove weld单斜角槽焊single-fillet weld单边角接焊缝single-pass weld单道焊site weld现场焊接; 安装焊; 安装焊接size of a fillet weld焊角尺寸size of weld焊件的大小; 焊区尺寸skew weld斜焊skin weld表面焊接sleeve weld套筒焊接slip-weld hanger卡瓦焊接套管挂slot weld槽塞焊; 长孔焊; 开槽搭焊缝; 切口焊缝ing slotted weld槽焊slotted lap weld切口搭接焊smooth fillet weld平填角焊缝socket weld ends承插焊接端soft-weld铜镍焊条合金solvent weld溶剂焊接space of intermittent weld断续焊缝间距; 断续焊间距spiral weld螺旋形焊缝spiral weld-pipe mill螺旋焊管机spot weld焊点spot weld bonding胶结点焊spot weld nugget点焊熔核spreading weld宽缝焊接; 加宽的焊缝square butt weld平头对接焊缝square groove weld无坡口槽焊staggered intermittent fillet weld (ing)交错断续角焊staggered intermittent weld交错断续焊缝; 交错间断焊staggered plug weld交错塞焊standard reinforced fillet weld标准加强角焊缝stick-out weld未熔合点焊接头stitch-and-seam weld点线焊straight butt weld无坡口对接接头strapped weld搭板对接焊缝strength weld受载焊缝; 强固焊接; 承载焊缝; 高强度焊接structural weld强固焊缝surface of weld焊缝表面surface weld表面焊缝surface weld metal buildup表面焊缝金属的形成synthetic apparatus for weld thermal cycle焊接热循环模拟装置T weld丁字接头焊缝T-filled weld丁字形角焊T-fillet weld丁字接头角焊缝tack weld定位焊点; 定位焊缝; 临时点焊; 预焊; 平头焊接(welding)定位焊tandem arc weld前后弧焊temporary weld临时点固焊缝tension weld受拉焊缝test weld试焊throat depth (thickness) of fillet weld角焊缝厚度throat of fillet weld凹角焊喉; 填角焊缝喉长throat of weld凹角焊喉tight weld密封焊接; 致密焊缝tight-strong weld密实强固焊缝toe of the weld焊缝边界toe of weld焊趾toe weld趾部焊缝torch weld气焊焊缝total amount of weld fumes焊接发尘量transverse fillet weld横向角焊缝; 正面角焊transverse weld横向焊缝trial weld试验焊接undercut weld底切焊接undressed weld (增加焊缝)未加工焊缝unequal fillet weld焊脚不等的角焊缝unfitness of butt weld焊缝对口错边量union-melt weld埋弧焊unload weld非承载焊缝unspaced butted weld无间隙对接焊缝upgrading of boiler weld锅炉焊缝加强vertical fillet weld立焊角焊缝vertical weld立焊weak weld不强固焊缝weaving weld横向摆动焊缝weld焊; 焊接的; 补焊weld all around围焊weld appearance焊缝外观weld assembly焊接组件weld back-up焊缝背垫weld backing焊缝衬垫weld bead焊缝; 熔敷焊道weld bead height焊缝高度weld beading焊瘤weld bond熔合线weld bridge seam搭桥焊缝; 桥接焊缝weld cap焊帽weld center line焊缝中心线weld collar加强焊缝焊瘤weld crack焊接裂纹weld crater熔池weld crosswise交叉焊接weld decay焊缝腐蚀; 焊接接头晶间腐蚀; 焊接侵蚀; 焊接区晶间腐蚀weld decay (焊接后)敏化区腐蚀weld defect焊接缺陷weld delay time焊接延迟时间weld deposit堆焊weld deposits cleaning焊接熔敷金属清理weld edge焊缝边缘; 焊缝表面边缘weld edgewise沿边焊接weld flange connection焊接法兰连接weld flash焊瘤weld flaw焊接缺陷weld flush焊缝隆起weld fumes焊接烟尘weld gage焊缝检查规; 焊缝卡规weld gauge焊缝量规weld heat input焊接热输入; 焊接线能量weld holder焊接夹持架; 焊接架weld inspection焊缝质量检验; 焊接检查weld interface焊缝界面; 焊接界面weld interval焊接时间weld is accepted焊缝合格weld jig焊接夹具weld joint焊缝weld junction熔焊线; 熔合线weld layer焊接层weld length焊缝长度weld line焊缝线; 焊缝轴线; 焊接线; 焊线weld machined flush削平补强的焊缝weld mark焊缝符号; 焊缝记号; 焊接痕; 熔缝weld mesh crate焊接网格weld metal焊缝金属; 焊接金属weld metal buildup surface金属堆焊表面weld metal composition焊接金属组成weld metal cracking焊缝裂纹weld metal zone焊缝金属区; 焊接金属熔化区weld nugget焊点熔核weld on bottom底焊weld overlap重叠区weld pass焊接通道weld penetration焊缝熔深; 焊透深度weld period焊接时间weld pitch焊缝距weld porosity焊缝气孔weld preheating焊前预热weld preparation焊缝坡口加工weld puddle熔池weld reinforcement焊缝补强; 焊缝加强; 焊接补强weld repairs焊接修补weld ripple焊缝波纹weld root焊件剖口; 焊接根weld root opening gap焊缝根部间隙weld root reinforcement焊缝反面加强weld rotation焊缝转角weld seam pipe焊缝管weld shape焊缝形状weld shielding焊接区保护; 焊接熔池保护weld slope焊缝倾角weld spacing焊点距; 焊缝间距weld strain焊接应变weld strength焊接强度weld surface焊缝表面weld swell焊缝隆起weld thermal cycle焊接热循环weld thickness焊缝厚度weld time焊接时间; 焊接通电时间; 接触焊通电时间weld toxic gases焊接有害气体weld trimmer焊缝清理机weld up焊补weld wheel conditioner焊轮调节器weld width焊缝宽度weld wire包铜钢丝weld zone焊缝区; 焊接区weld-form factor焊缝形状系数weld-fusion line焊缝熔合线weld-in nozzle焊入式喷嘴weld-interval timer焊接间隔记时器weld-shrunk cylinder包扎式圆筒weld-shrunk multilayered cylinder包扎式多层圆筒; 多层包扎式圆筒weld-throat thickness depth焊缝厚度window type restraint weld cracking test窗口拘束焊缝抗裂试验; 窗形拘束抗裂试验zigzag intermittent fillet weld锯齿形断续角焊缝; 锯齿形断续角焊缝zone of weld焊缝表面AC & D. C. arc welding machine交直流弧焊机AC arc welding交流电弧焊AC gas metal-arc welding process交流熔化极气保护焊AC gas tungsten arc welding交流钨极气保护焊AC welding set交流焊机; 交流焊接变压器AC-dc welding machine交直流两用焊机acetylene welding气焊; 乙炔焊; 乙炔焊接acetylene welding torch乙炔焊炬; 乙炔接焊吹管air-acetylene welding空气-乙炔焊接all-position welding全位置焊接alloy steel gas welding rod合金钢气焊条alternating current arc welding交流电弧焊alternating current welding machine交流电焊机aluminium alloy arc welding electrode铝合金焊条aluminothermic welding铝热焊; 铸焊angle backwards welding后倾焊angle butt welding斜口对接焊angle forwards welding前倾焊annealing welding wave退火焊波antogenous welding氧炔焊apparatus for butt welding平接压焊夹具arc braze welding电弧钎焊arc flash welding电弧闪光焊arc spot welding电铆焊arc stud welding柱钉电弧焊; 螺柱电弧焊arc voltage feedback controlling arc welding弧压反馈电弧焊arc welding电弧焊; 电弧焊接; 弧焊arc welding electrode电弧焊条arc welding generator电弧焊接用发电机; 弧焊发电机arc welding generator with independent excitation自激弧焊发电机; 他激电焊发电机arc welding generator with self-excitation自激电焊发电机arc welding machine弧焊机; 电焊机; 电弧焊机arc welding mask电弧焊遮罩arc welding process电弧焊接工艺过程arc welding rectifier弧焊整流器arc welding robot弧焊机器人arc welding set电弧焊机组arc welding transformer弧焊变压器arc-welding electrode电弧焊用焊条arc-welding plant电焊厂arcogen welding电弧氧乙炔焊argon (shielded) arc welding氩弧焊接argon tungsten-arc welding钨极氩弧焊argon-arc welding氩弧焊argonaut welding自动氩弧焊atomic H welding氢原子焊atomic hydrogen welding原子氢焊atomic-hydrogen welding原子氢焊接austenite welding不锈钢焊接autogenous pressure welding自动压合热焊autogenous welding气焊automatic arc welding head自动电弧焊接机头automatic arc welding machine自动电焊机; 自动弧焊机automatic drying line for welding electrode电焊条自动烘焙线automatic slag pool welding自动电渣焊automatic spot welding自动点焊automatic submerged arc welding自动埋弧焊automatic submerged slag welding of rail钢轨automatic submerged-arc welding machine埋弧自动焊机automatic transverse welding横向自动焊automatic welding自动焊; 自动焊接automatic welding head自动焊头automatic welding machine自动焊接机automatic welding of circumferential seams环缝自动焊automatic welding process自动焊接工艺规程automation of welding焊接自动化back hand welding后退焊; 反手焊接back step welding反手焊接back ward welding反手焊接back welding底焊; 退焊法back-step welding分段退焊法backhand welding逆向焊; 右焊法; 后焊法; 向后焊backing welding打底焊backstep welding分段逆焊; 分段退焊; 反向焊; 逐步退焊法; 逆向焊backstep welding sequence分段退焊次序backward welding后倾焊; 后退焊; 向右焊balanced welding对称焊bare welding rod光焊条bare wire arc welding光焊丝电弧焊bead welding窄焊道焊接bench arc welding machine台式弧焊机bevel welding斜角焊blacksmith welding锻工焊接; 锻焊block sequence welding分段多层焊; 分段连续焊接block welding块焊接block welding sequence分段多层焊body welding machine罐身焊接机both sides welding双面焊接brass welding rod黄铜焊条braze welding钎焊; 钎焊接; 钎接; 铜焊braze-welding钎接焊bridge spot welding带接合板点焊; 单面衬垫点焊; 单面搭板点焊bridge welding桥接焊; 盖板焊brize welding硬焊build (built) up welding堆焊build-up welding堆焊building-up by welding堆焊butt resistance welding电阻对焊; 对接电阻焊butt seam welding对接滚焊butt seam welding machine对接缝焊机butt welding对接焊; 平对焊butt welding machine对接焊机butt welding process对接焊法butt-welding对接焊butt-welding machine对焊机capability of welding vertically upwards直上焊接能力capacitor-discharge welding电容放电焊接carbon arc welding碳弧焊; 碳极弧焊carbon in materials for welding焊接用材料中的碳carbon-dioxide arc welding二氧化碳保护焊carriage of automatic welding machine自动焊机走架cascade welding阶梯式焊; 山形多层焊cascade welding sequence串级叠置法cast welding铸焊cement-welding金属陶瓷焊接centralized installation of welding machine多站焊接chain intermittent fillet welding并列断续角焊缝; 链式断续角焊chemical welding化学焊circular seam welding环缝对接焊circular seam-welding machine环形滚焊机cleaning before welding焊接前的清理cleaning of welding deposits焊接沉积的清理closed butt gas pressure welding闭式加压气焊cold welding冷焊; 冷压焊cold-pressure welding冷压焊combined cutting and welding torch焊割两用炬combined cutting and-welding blow-pipe焊割两用炬combined thermit welding加压铸焊complete penetraction and fusion in welding全焊透condenser (discharge) spot-welding machine电容器放电点焊机condenser discharge spot welding电容储能点焊; 电容贮能点焊constant current welding machine恒流电焊机constant energy welding machine恒功率电焊机constant voltage welding machine恒压电焊机constant-current arc welding power source垂降特性弧焊电源constant-current welding source恒流式焊接电源constant-power welding source恒功率式焊接电源constant-pressure pressure welding恒压压力焊constant-temperature pressure welding恒温压力焊constant-voltage welding machine恒电压焊机constant-voltage welding source恒压式焊接电源; 平特性焊接电源consumable electrode welding熔化极电弧焊consumable guide electroslag welding自耗定向电渣焊contact welding接触焊continuous feed welding连续送丝电弧焊continuous welding连续焊; 连续焊接contour welding绕焊controlled arc welding可控电弧焊接controlled atmosohere arc welding充气室电弧焊controlled atmospere arc welding充气式电弧焊controlled tungsten-arc welding自动控制弧长的钨极电弧焊controlled-transfer welding可控过渡电弧焊convex fillet welding凸面角焊缝copper arc welding electrode铜焊条copper welding rod铜焊条copper-alloy arc welding electrode铜合金焊条copper-aluminium welding rod铜铝焊条copper-nickel welding rod铜镍焊条copper-silicon welding rod铜硅焊条copper-tin welding rod铜锡焊条copper-zinc welding rod铜锌焊条core welding-wire焊芯core wire for welding rod焊条芯线corrosion due to welding焊接腐蚀cosmetic welding盖面焊cover chain welding链节式药皮包丝焊接CO 2 arc welding machine二氧化碳弧焊机cracking test for automatic welding自动焊抗裂试验crankshaft flashbutt welding曲轴电阻弧花压焊cross welding横向焊缝cyc-arc welding圆环电弧焊deck welding重力焊deep fillet welding深角焊deep penetration welding深熔焊deep penetration welding electrode深熔焊条deep welding深焊die welding模焊; 冲模堆焊diesel engine driven DC arc welding machine柴油机驱动直流弧焊机differential-excited welding generator差激电焊发电机diffusion welding扩散焊接direct spot welding双面点焊direct welding双面点焊direction of welding焊接方位; 焊接方向discontinuous welding断续焊dot welding点焊double carbon-arc welding间接碳弧焊double side welding双面焊接down-hand welding俯焊downhand welding平焊downward welding in the inclined position下坡焊downward welding in the vertical position向下立焊dual-arc welding双弧焊edge seam welding端面接头滚焊edge welding边缘焊接edgewise welding沿边焊接electric and pressure welding电压力焊接electric arc spot welding电弧点焊electric arc welding generators电弧焊接发电机electric arc welding machine电弧焊机electric butt welding电阻接触焊electric resistance welding电阻焊接; 热电阻焊electric slag welding电渣焊electric spot welding电点焊electric welding电焊electric welding cast copper solder铸铜电焊条electric welding equipment电焊设备electric welding generator电焊发电机electric welding hammer电焊锤electric welding machine电焊机electric welding plant电焊厂electric welding pliers电焊钳electric welding rod电焊条electric welding strip电焊片electric-arc welding电弧焊electric-resistance seam-welding电阻缝焊electric-resistance seam-welding machine电阻缝焊机electrical arc welding电弧焊接electrical resistance welding tube电阻焊接管electrically heated welding torch电热焊枪electro-beam welding电子束焊接electro-gas (enclosed) welding气电立焊electro-slag welding电磁渣焊; 电渣焊electro-slag welding with plate electrode板极电渣焊electro-welding电焊electrode for arc welding电焊条; 电弧焊条electrode for vertical down welding向下立焊条electrode of vertical down welding立向下焊条electrode welding电弧焊electrogas welding气电焊; 电气焊electromagnetic percussive welding电磁冲击焊electromagnetic stored energy welding电磁储能焊electron beam welding电子束焊; 电子束焊接electron beam welding machine电子束焊接机electron-beam welding电子束焊接electron-beam welding machine电子束焊机electron-bombardment welding真空电子束焊electrons leaves welding电子束焊接electropercussive welding电冲击焊; 冲击焊; 储能焊electroslag welding电渣焊; 电阻焊electroslag welding machine电渣焊机electroslag welding with consumable nozzle熔嘴电渣焊electroslag welding with wire electrode丝极电渣焊electrostatic (percussive) welding电能储能焊接electrostatic percussing welding静电焊; 静电焊; 冲击焊; 储能焊electrostatic percussive welding静电冲击焊; 静电冲击焊enclosed welding强制成形焊接energy storage welding贮能焊; 储能焊; 脉冲焊接erecting welding装配焊接erection welding安装焊接eutectic welding低温焊exothermic welding铝热焊expanding or welding of tube with tubesheet管子与管板的胀接或焊接explosive welding (EW)爆炸焊eyelet welding孔焊; 小孔熔焊faster welding快速焊接feed rate of welding wire焊丝送进速度field of welding temperature焊接温度场field welding现场焊接; 工地焊接Filler arc welding菲拉电弧焊距fillet welding (填角焊)贴角焊fillet welding in the downhand position船形角焊fillet welding in the flat position船形焊fillet welding in the horizontal position横角焊fillet welding in the vertical position立角焊fine welding精密焊接fine wire welding细丝焊fire cracker welding躺焊fire welding锻焊; 锻接fixed welding machine固定式焊机fixed-position welding定位焊接flame welding熔气焊flare welding喇叭形坡口焊接flash butt welding闪光对焊; 闪光对接焊wire welding焊网flash welding闪光电弧焊; 闪光焊; 闪焊; 火花电弧焊; 火花对焊flash-butt welding电阻闪光焊接flashover welding闪光焊flat position welding平焊; 顶面平卧焊flat position welding of fillet weld角焊缝平焊; 船形角焊flat welding平卧焊flexible welding rod软焊条flexible wire for electric welding电焊软线flow welding流注焊接; 浇焊fluid welding流焊flux-cored welding包芯焊条焊接fly-wheel type friction welding贮能摩擦焊; 储能摩擦焊flywheel friction welding惯性摩擦焊forehand welding向前焊; 向左焊; 左焊法; 左向焊; 正手焊forge welding锻焊; 锻接焊forward welding正手焊; 左焊法; 左向焊; 前进焊; 前倾焊; 向前焊friction welding摩擦焊; 摩擦焊接friction welding machine摩擦焊接机frontal fillet welding正面角焊full automatic welding全自动焊full-automatic arc welding全自动电弧焊full-fillet welding满角焊full-fusion thermit welding热剂铸焊full-fusion welding全熔合焊full-length welding满焊fusion pressure welding熔化压接fusion thermit welding热剂熔焊; 熔化铝热焊fusion type plasma arc welding熔透型等离子弧焊fusion type welding熔透型焊接法fusion welding熔焊接fusion welding metal熔焊金属gas carbon-arc welding气保护碳弧焊gas electric welding气电联合焊接gas metal arc welding气体保护金属极电弧焊gas metal-arc welding气保护金属极电弧焊gas shield welding气体保护弧焊gas shielded arc welding气体保护电弧焊; 气体保护焊gas shielded arc welding machine气保护弧焊机gas shielded arc-welding machine气体保护弧焊机gas shielded magnetic flux arc welding磁性焊剂气体保护电弧焊gas shielded metal-arc welding气体保护金属弧焊gas shielded welding气体保护焊gas torch welding气炬焊gas tungsten arc welding气体保护钨极电弧焊gas tungsten-arc welding气保护钨极电弧焊gas tungstun arc welding钨极气体保护焊gas welding气焊; 乙炔焊gas welding device气焊设备gas welding equipment气焊设备gas welding machine气焊机gas welding outfit气焊机gas welding rod气焊焊丝gas welding rubber hose气焊橡胶管gas welding technique气焊工艺gas welding torch butt气焊进气硬管gas welding tube mill瓦斯焊接机gas welding work气焊工作gas-arc welding气电焊; 气体保护电弧焊gas-arc welding gun气电焊焊嘴gas-press welding气压焊gas-pressure welding machine气压焊接机gas-shielded stud welding气保护柱钉焊接girth welding环缝横向焊接gravity type arc welding重力焊gravity type welding倚焊gravity welding重力焊; 重力式电弧焊groove welding槽焊; 坡口焊; 开槽焊guided automatic welding导向自动焊接gun welding machine手提式点焊机; 点焊枪hafnium welding wire铪焊丝hammer welding锻焊; 锻接; 锤焊hammered resistance welding锤锻电阻焊; 电阻加热锻焊hand welding holdet手焊焊把hard-welding硬质合金熔焊headless bolt for welding焊接单头螺栓heat-welding adhesive热熔性胶粘剂heated-tool welding热烙铁焊接heavy welding大断面焊接heavy welding electrode粗电焊条heliarc welding氦电弧焊Heliarc welding氦弧焊法helium arc welding氦弧焊HF welding magnetic bar高频焊接磁棒hidden arc welding埋弧焊; 潜弧焊high current arc welding大电流弧焊high frequency AC welding machine高频交流电焊机high frequency dielectric welding高频介电焊high frequency induction welding高频感应焊high frequency welding高频焊接high grade energy welding高能焊high tensile electric welding rod高强焊条high-current plasma arc welding大电流等离子弧焊high-frequency induction welding高频感应焊接; 高频焊接high-frequency resistance welding高频接触焊high-frequency resistance welding (HFRW)高频电阻焊high-frequency welding高频电焊highspeed welding快速焊接horizontal fillet welding横角焊; 水平角焊horizontal position welding水平焊接; 横焊horizontal welding横焊; 水平焊horizontal-position welding水平位置焊接horizontal-rolledposition welding水平转动焊接; 滚动水平焊hot jet welding热风焊接hot press welding热压焊接hot pressure welding预热压力焊hot welding热焊hot wire welding热丝焊hot(-)gas welding热气焊接hot-gas welding热风焊接; 热空气焊接hot-pressure welding热压焊; 热压焊接hydrogen-welding氢焊impact spot welding冲击点焊法impregnated-tape metal-arc welding浸焊条金属弧焊impulse current automatic butt welding machine脉冲电流自动对焊机impulse current seam welding machine脉冲电流缝焊机impulse current semiautomatic butt welding machine脉冲电流半自动对焊机impulse electromagnetic automatic welding machine电磁脉冲自动焊机impulse plasma welding machine脉冲等离子焊机impulse welding脉冲焊; 脉冲焊接impulsed spot welding脉冲点焊inclined position welding倾斜焊indirect (spot) welding单面点焊indirect welding单面点焊induction welding感应焊; 感应焊接; 感应熔焊inert gas arc spot welding惰性气体电弧点焊inert gas arc welding惰性气体电弧焊inert gas spot welding惰性气体保护电弧点焊inert gas welding惰性气体焊接法inert-gas (inert gas) arc welding惰性气体保护焊inertia welding惯性焊接; 贮能摩擦焊; 储能摩擦焊inertial welding惯性焊接infrared welding红外线焊接intermediate current plasma arc welding中电流等离子弧焊intermittent fillet welding断续角焊intermittent point welding断续点焊intermittent welding断续焊International Institute of welding (IIW)国际焊接学会inverted welding仰焊joint welding搭焊jump welding丁字形焊keyhole-mode welding小孔型等离子弧焊; 穿透型焊接法lap fillet welding搭角焊; 搭接角焊lap resistance welding搭接电阻焊lap seam welding搭接缝焊; 搭接焊lap welding搭焊; 搭接焊laser welding激光焊接laser welding chamber激光焊接室laser welding head激光焊接头laser welding machine for orthodontics激光口腔矫形焊接机laser welding system激光焊接系统laser-beam welding machine激光焊接机laser-welding machine激光焊接器lead welding铅焊lefthand welding左焊法leftward welding左向焊法lever gun welding head杠杆式点焊钳light beam welding machine光束焊机light continuous welding轻连续焊接light gauge welding薄板焊接light ray welding光束焊接light welding轻焊接Linde welding林德钢管对焊法line welding直线焊缝焊接liquid metal welding浇注补焊longitudinal resistance seam welding纵向电阻缝焊longitudinal seam welding纵缝焊接; 纵向缝焊longitudinal welding纵缝焊接; 纵向焊接low carbon steel welding electrode低碳钢电焊条low carbon welding wires低碳焊接线材low idle voltage arc-welding power supply低空载电压的弧焊电源low temperature welding低温焊接low-alloy steel covered arc welding electrode低合金钢焊条low-current plasma arc welding小电流等离子弧焊low-hydrogen welding electrode低氢型电焊条low-temperature welding低温焊接lowest permissible temperature for welding焊接允许的最低温度machine for magnetic welding磁力焊接机machine welding机器焊接machine welding torch机械焊接吹管magnetic discharge welding电磁储能焊; 电磁焊magnetic flux arc welding磁性焊剂电弧焊magnetic flux gas shielded arc welding磁性焊剂气体保护电弧焊magnetic force welding machine磁力焊接机magnetic-force welding磁力焊接法manual arc welding手工电弧堆焊manual electic arc pile up welding手工电弧堆焊manual electric arc welding手工电弧堆焊manual electro-slag welding手工电渣焊manual gas welding手工气焊manual metal-arc welding手弧焊manual TIG welding手工钨极惰性气体保护焊manual welding手工焊接; 人工焊接manual welding machine手工焊机manually coating welding electrode手涂焊条mash seam welding滚压电阻缝焊mash stitch welding多针缝式焊接mask welding电焊眼罩match assemble welding装架焊接metal arc welding金属电弧焊metal buried welding埋渣焊metal inert gas arc welding (MIG)惰性气体金属电弧焊metal inert-gas arc welding金属极惰性气体保护焊metal inertia gas welding金属焊条惰性气体保护焊; 熔化极惰性气体保护焊metal rectifier welding set整流焊机metal-arc gas-shielded welding气保护金属极电弧焊metal-arc gas-shielded welding (MAGSW)金属极气保护焊metal-arc welding金属极电弧焊micro resistance welding显微电阻焊micro-gap welding微间隙焊接micro-plasma arc welding微束等离子弧焊micro-welding微型焊接; 显微焊接microgap welding微隙间隙焊Miebach high efficiency flash welding machine米巴赫高效闪光对焊机mild steel arc welding electrode低碳钢焊条mild steel welding rod低碳钢焊丝miter welding斜接头焊接mixed gas arc welding混合气体保护电弧焊molten bath arc welding熔池电弧焊molten-bath arc welding熔池焊motor driven welding machine电动焊机; 电动机拖动式焊机motor-driven welding machine电动旋转式焊机motor-generator welding unit电动直流发电焊接设备multi-head automatic arc-welding machine多头自动电弧焊机multi-head automatic welding machine多头自动焊机multi-operator welding set多站电焊机multi-pass (multiple pass) welding多道焊multiarc welding多弧焊multihead automatic arc welding machine多弧自动电焊机multilayer welding多层焊multioperator welding generator多工位焊接发电机multioperator welding machine多站电焊机; 多站焊机multioperator welding set多站焊机multipass welding多道焊接multiple arc welding多弧焊multiple operator arc welding machine复式弧焊机multiple projection welding多点凸焊multiple resistance welding多点电阻焊接; 复式电阻焊multiple spot welding多点点焊multiple spot welding machine多点点焊机multiple-arc welding plant多弧焊接机multiple-electrode spot welding machine多极点焊机multiple-electrode welding多焊条焊接multiple-impulse welding多脉冲焊; 多脉冲接触焊multiple-operator welding-unit多重操作焊接单元multiple-spot welding多点焊multiple-wire multiple-power submerged-arc welding多丝埋弧焊multiple-wire submerged arc welding多丝埋弧焊multiplewire submerged-arc welding多丝埋弧焊nail head type welding钉头式焊接narrow gap one side welding窄间隙单面焊narrow gap one-side automatic welding窄间隙单面自动电弧焊narrow gap welding窄间隙焊接; 狭间隙焊negative polarity welding反极性焊接neli-arc welding氦电弧焊nickel bare welding filter metal镍焊丝nickel covered welding eleetrode镍药皮焊条nickel steel gas welding rod镍钢气焊条nickel-base alloy bare welding filler metal镍基合金焊丝nitrogen-arc welding氮弧焊。
2021年-焊接专业术语中英文对照整理
机械——焊接专业术语中英文对照（郭运）整理1Single单面的2V—groove V 型坡口3Joint焊接接头4Edges overlap接头形式5Butt对接6T T 型焊接7Fillet角焊缝8Edge端接9Corner角接10Radius半径11Joint root焊接根部12Bevel angle削边角度13Groove angle坡口角度14Root face根部钝边15Groove face坡口面16Plug weld塞焊17Spot weld点焊18Seam weld缝焊19Slot weld槽焊20Double—flare—bevel—groove K 型坡口焊缝21Single—flare—V单面 V型22Edge flange翻边端接23Corner flange卷边端接24Flange weld卷边焊缝25Flare weld扩口焊缝26Fillet weld角焊缝27Slot weld槽焊缝28Spot weld点焊缝29Surfacing weld堆焊焊缝30Melt —through weld熔透焊缝31Backing weld打底焊缝32Back weld背面焊缝33Root weld根部焊缝34Crown weld隆起部分35Weld reinforcement焊缝加强36Weld face焊缝表面37Cap pass盖面焊道38Weld edge焊缝边缘39Leg焊脚40Toe焊趾41Buildup堆焊42Weld reinforcement焊缝加强高43Effective throat有效焊喉44Concave weld凹形焊缝45Convex weld凸形焊缝46Unequal leg fillet不等脚角焊47Oversize weld大尺寸焊缝48Depth of fusion熔合深度49Depth of penetration熔透深度50Root penetration根部熔深51Joint penetration接头熔深52Weld interface焊缝分界面53Diameter of weld at point of contact焊缝在接触点上的直径54Thickness厚度55Tail尾部56Arrow箭头57Reference line参考线58Arrow side箭头一边59Weld symbol焊缝符号60Near side近侧61Arrow side箭头侧62Far side远侧63Other side另一侧64Put the weld on either—side在任意一侧施焊65There is no side significance没有方向区别66Edge flange双卷边67Corner flange单卷边68Weld size焊缝尺寸69Effective throat有效厚度70Root opening根部间隙71Full penetration double bevel —groove weld K 形坡口全焊透焊缝72Full penetration double V—groove weld双 V 形坡口全焊透焊缝73Partial penetration double bevel—groove weld K形坡口部分焊透焊缝74Partial penetration double V—groove weld双 V形坡口部分焊透焊缝75Bevel groove削边坡口76Flare groove喇叭形坡口77Flange groove卷边坡口78V—groove V 形坡口79Staggered intermittent fillet weld交错间断角焊缝80Chain intermittent fillet weld链状间断角81Segmented fillet weld分段角焊缝82Pitch distance间距83Depth of filling填充深度84Slot weld width槽焊缝宽度85Plug weld diameter塞焊缝的直径86Angle of countersink深孔角度87A dimension to the right of the symbol在符号右边的尺寸88 A dimension of the required suggest diameter 所要求的直径尺寸89 A value for the required shear strength per spot 每点所要求的剪切强度值90Spot weld size点焊缝尺寸91Spot weld length点焊缝的长度92Number of spot required所要求的点的数量93Pitch distance between adjacent spots两个相邻点的间距94Reference line参考线95Melt —through of weld from other side焊缝在另一96Single bevel—groove weld with backing weld 加垫板的单边坡口焊缝97 Single bevel—groove weld with back weld背面焊的单边坡口焊缝98Single bevel—groove weld with backing weld 带垫板的 V 形坡口焊缝99Single bevel—groove weld with back weld 背面焊的 V 形坡口焊缝100Square groove直边坡口101Skewed groove斜坡口102Sloped groove倾斜坡口103Scarf斜嵌接104Gas metal arc spot weld气体保护点焊105Resistance spot weld电阻点焊106Gas metal arc seam weld气体保护滚焊缝107Resistance seam weld电阻滚焊缝108Gas metal arc slot weld气体保护槽焊缝109The type of electrode to use所要求焊条形式110The weld quality standard焊缝质量标准111The weld procedure to use所用的焊接程序112Codes规范113Drawing图纸114Specifications技术要求115Contracts合同116General一般注解117Local局部注解118The point for lifting an object吊装一物体的点119Filler metals填充金属120Pressure vessel fabrication压力容器制造121Be as simple as possible尽可能简单122Welder焊工123Code body规范本身124Shielded metal arc手工电弧焊125Submerged arc埋弧焊126Face bend面弯127Root bend背弯128Side bend侧弯129Nick break缺口破坏130Tensile拉伸131Monitoring production welding监视生产中的焊接132Strength强度133Toughness韧性134Hardness硬度135Ductility延展性136Compressive压缩137Impact冲击138Fatigue疲劳139Undercut咬边140Overlap焊瘤141Cracking裂纹142Porosity气孔143Ultimate tensile strength极限拉伸强度144Percent elongation延伸率145Percent reduction of area断面收缩率146Impact strength冲击强度147Yield strength屈服强度148Brinell布氏149Vickers韦氏150Rockwell洛氏151Knoop努氏152Fatigue test疲劳试验153Tensile test拉伸试验154Micro--hardness test显微硬度试验155Charpy impact test夏比冲击试验156Soundness test致密性测试157Fillet break角焊缝断裂158Metallographic金相159Transverse fillet weld shear test横向角焊缝剪切试验160Quality of the fractured weld焊缝端口的质量161Ductility of the weld metal焊缝金属的延展性162Impact strength of the weld焊缝的冲击强度163Tensile strength of the base metal母材的拉伸强度164Weld—ability可焊性165Scratchescaused by improper handling 由不适当的处理导致的划痕166Incomplete fusion未熔合167Distortion变形168Slag inclusions夹渣169Vibratory stress relief振动消除应力170External restraint外部拘束171Thermal stress relief热消除应力172Peening锤击173Annealing退火174Quenching淬火175Tempering回火176Normalizing正火177Decrease current降低电流178Decrease voltage降低电压179Increase travel speed加快焊接速度180Change from weave to stringer bead technique 从横向摆动焊道改成直线焊道技术181Result in a wider heat —affected zone hardness导致热影响区更宽182Produce a lower heat —affected zone hardness 降低热影响区硬度183Slow down the cooling rate降低冷却速度184Reduce the tendency to produce martensite in the heat—affected zone减少在热影响区形成马氏体的倾向185Stress relief消除应力186Crater crack弧坑裂纹187SMAW手动电弧焊188PAW等离子焊189FCAW药芯焊190SAW埋弧焊191Underfill未焊满192Excess convexity太凸193Excess weld reinforcement焊缝余高太高194Overfill过充195Scratch start擦伤196Arc strike引弧烧伤197Tungsten inclusion夹钨198Lamination分层199Lamellar tear片状撕裂200Seam划伤201Pipe shrinkage缩孔202Longitudinal crack纵向裂纹203Transverse crack横向裂纹204Underbead crack焊道中裂纹205Toe crack焊趾裂纹206Root crack根部裂纹207Base metal crack母材裂纹208Before welding焊接前209During welding焊接时210After welding焊接后211Waiting time等待时间212Penetrating time渗透时间213Soak time吸入时间214Dwell time驻留时间215AC交流电216DC直流电217DCEP直流反接218。
焊接名词中英文对照
continuous weld process连续式炉焊管法
contour weld特形焊接
convex fillet weld凸角焊缝; 凸形角焊缝
convex weld凸焊缝; 凸形焊缝
copper weld wire包铜钢丝
corner flange weld单卷边角焊缝
表面裂纹surface crack
咬边undercut
焊瘤overlap
凹坑pit
烧穿burn through
塌陷excessive penetration
未焊透incomplete penetration/ lack of penetration
未熔合lack of fusion/ incomplete fusion
X射线工业电视探伤X-ray industrial television inspection
磁粉探伤magnetic particle inspection
电磁探伤electromagnetic inspection/ eddy current test
探伤灵敏度flaw detection sensitivity
dissimilar weld metal不同的焊接金属; 不同金属的焊接
distance between the toes of a weld焊缝宽度
double groove weld双面坡口焊缝
double-bevel groove weld双斜边坡口焊缝; 双斜坡口焊
double-flanged butt weld双弯边对接焊缝
比较全面的焊接英语词汇，可以直接看不用下载呀
焊接专业术语中英对照
焊接专业术语中英对照焊接欠缺与检验焊接欠缺welding imperfection焊接缺陷weld defect气孔blowhole/ gas pore针尖状气孔pinhole密集气孔porosity条虫状气孔wormhole裂纹crack表面裂纹surface crack咬边undercut焊瘤overlap凹坑pit烧穿burn through塌陷excessive penetration未焊透incomplete penetration/ lack of penetration未熔合lack of fusion/ incomplete fusion 未焊满incompletely filled weld根部凹陷root concavity电弧擦伤arc scratch夹渣slag inclusion夹杂物inclusion夹钨tungsten inclusion白点fish eye/ flake错边misalignment/ dislocation焊接检验试件test piece试样test specimen无损检验nondestructive test破坏检验destructive test外观检查visual examination超声波探伤ultrasonic inspection直射法超声波探伤straight beam method斜射法超声波探伤angle beam method液浸法超声波探伤immersion method射线探伤radiographic inspection/ radiographyX射线探伤X-ray radiographic inspection γ射线探伤gamma-ray inspectionX射线工业电视探伤X-ray industrial television inspection磁粉探伤magnetic particle inspection电磁探伤electromagnetic inspection/ eddy current test探伤灵敏度flaw detection sensitivity渗透探伤penetration inspection荧光探伤flurescent penetrant inspection 着色探伤dye penetrant inspection密封性检验leak test气密性检验air tight test枕形气密检验pillow test耐压检验pressure test水压检验hydraulic test气压检验pneumatic test液晶检验liquid crystal test声发射检测acoustic emission testing面弯试验face bend testing背弯试验root bend test侧弯试验side bend test横弯试验horizontal bend test纵弯试验axial bend test压扁试验squeezing testactual weld-throat thick-ness焊缝厚度all-around weld整周焊缝all-around weld (整周焊缝)环焊缝angle butt weld斜对接焊angle weld角焊appearance of weld焊缝成形arc-seam weld电弧缝焊arc-spot weld电弧点焊arc-weld电弧焊aspect ratio of weld焊缝成形系数at weld edge在焊缝边上attachment weld连接焊缝automatic spot weld自动点焊法automatic weld自动焊接axis of a weld焊缝行南焊接轴线axis of weld焊缝轴线; 焊接轴线back of weld焊缝背面backing groove of weld焊缝反面坡口backing weld底焊; 底焊焊缝bare metal arc weld裸焊条电弧焊bead weld珠焊; 堆焊bead-on-plate weld堆焊焊缝beading weld凸焊beam-to-beam weld梁间焊接; 梁式引线焊接block sequence weld分段多层焊bond weld钢轨接头焊接bridge seam weld桥缝焊接; 桥线焊brize weld硬焊butt weld对接焊缝butt weld ends对头焊接端butt-weld碰焊; 平式焊接; 对头焊接butt-weld in the downhand position对接平焊butt-weld joint对头焊接butt-weld pipe mill对焊管轧机button spot weld按电钮点焊cap weld最后焊层; 盖面焊缝carbon content of weld materials焊接材料的碳含量cast-weld construction铸焊结构caulk weld填缝焊caulking weld密实焊缝chain intermittent fillet weld链式分段角焊; 并列间断角焊缝chain intermittent weld并列焊接circular weld环形焊缝circumferential weld环缝; 环焊缝cleft weld裂口焊closed weld底边无缝焊; 无间隙焊缝closed-chamber fusion weld闭室熔焊cluster weld丛聚焊缝coil weld卷板对接焊; 卷板对接焊; 板卷焊cold weld冷压接commutator-controlled weld换向控制焊接complete penetration butt weld贯穿对焊composite weld紧密焊缝; 强度密封焊缝concave filled weld凹形角焊缝concave filler weld凹角焊concave fillet weld凹面填角焊concave weld凹焊缝; 凹面焊; 凹形焊缝; 轻型焊connective weld联系焊缝continuous butt-weld mill连续式炉焊管机组continuous fillet weld连续(填)角焊缝; 连续角焊缝; 连续贴角焊continuous weld连续焊缝continuous weld process连续式炉焊管法contour weld特形焊接convex fillet weld凸角焊缝; 凸形角焊缝convex weld凸焊缝; 凸形焊缝copper weld wire包铜钢丝corner flange weld单卷边角焊缝corner weld角焊corner-flange weld卷边角焊缝; 卷边角焊缝crack of weld焊部裂纹cross weld十字交叉焊缝; 横向焊缝cross-wire weld十字焊crotch weld楔接锻接; 楔接焊接cup weld带盖板焊缝depth of weld焊接深度dissimilar weld metal不同的焊接金属; 不同金属的焊接distance between the toes of a weld焊缝宽度double groove weld双面坡口焊缝double-bevel groove weld双斜边坡口焊缝; 双斜坡口焊double-flanged butt weld双弯边对接焊缝double-V groove weld双斜边坡口焊缝; 双斜坡口焊downhand weld平焊缝duplex spot weld双点点焊接头edge joint weld边缘焊edge weld端接焊; 端接焊缝; 端面焊缝; 对边焊electric resistance weld mill电阻焊管机electric weld-pipe mill电焊管机焊接专业英语词汇（通用部分）acetylene 乙炔 ampere 电流安培angle welding 角焊 arc 电弧argon arc welding 氩弧焊接 bare electrode 光熔接条butt welding 对接焊接 camber 电弧弯曲cascade 阶叠熔接法 clad weld 被覆熔接crator 焊疤 excess metal 多余金属filler rod 焊条 fillet weld 填角焊接gas shield 气体遮蔽 groove welding 起槽熔接hand face shield 手握面罩 hard facing 硬表面堆焊jig welding 工模焊接 laser beam welding 雷射光焊接metal electrode insert gas welding MIG熔接nugget 点焊熔核overlaying 堆焊 peening of welding 珠击熔接法plug welding 塞孔熔接 positioned welding 正向熔接pressure welding 压焊 propane gas cutting 丙烷气切割pure nickel electrode 纯镍熔接条reinforcement of weld 加强焊接resist 抗蚀护膜 root running 背面熔接seam 焊缝 seaming 接合seam welding 流缝熔接 series seam welding 串联缝熔接skip welding process 跳焊法 spark 火花spot welding 点焊接 stitch welding 针角焊接stud arc welding 电弧焊接 under laying 下部焊层void 焊接空隙 weld flow mark 焊接流痕weld flush 焊缝凸起 weld line 焊接纹weld mark 焊接痕 weld penetration 熔接透入weld zone 焊接区 welding 焊接welding bead 焊接泡 welding direction 焊接方向welding distortion 焊接变形 welding flux 焊剂welding ground 电熔接地 welding interval 焊接周期welding stress 熔接应变 welding torch 熔接气炬welding electrode production line 电焊条生产线welding electrode 焊条welding fixture 焊接夹具welding generator 电焊机welding goggles 焊工护目镜welding gun 焊枪welding helmet 电焊帽welding inspection ruler 焊接检验尺welding machine 焊接机welding mill 焊管机welding motor generator 电动焊接发电机welding nozzle 焊嘴welding paste 焊接药膏welding pipe 焊接管welding powder 焊粉welding rectifier 焊接整流器welding robot 焊接机器人welding rod extrusion press 焊条挤压机welding rod with acidic coating 酸性焊条welding rod with alkaline coating 碱性焊条welding rod 焊条welding simulator 焊接模拟器welding stainless electrode 不锈电焊条welding steel tube 焊接钢管welding tin billet 焊锡棒料welding tongs 焊接夹钳welding torch 焊炬welding transformer 电焊变压器welding unit 焊机welding wire machine 焊线机welding wire 焊丝welding-cutting hose 熔焊及切割胶管welding-cutting tool 焊割具welding-rod core 焊条芯welding-seam cleaner 焊缝清理机weldless pipe 无缝管weldless steel tube 无缝钢管well borer 凿井机well counter 井式计数器well deck vessel 井形甲板船well drill 钻井机well platform 钻井平台well rig 钻井机well testing truck 试井车well thermometer 井温计well tube filter 井管滤管well type tempering electric furnace 井式回火电炉well winch 矿井绞车well-logging probe 测井探头well-type counter 井型计数器Wella Balsam Conditioner 威娜宝护发素Wella Balsam shampoo 威娜宝香波Wellene 韦纶聚酯短纤维wellhead acid preventer 井口防酸器wellington 惠灵顿防雨呢Wellingtons 长筒皮靴Welltite 韦纶泰特聚丙烯和聚乙烯单丝Welsbach's alloy 韦尔斯巴赫发火合金Welsh flannel 威尔士法兰绒Welsh wool 威尔士粗羊毛welsh-onion stalk 葱白welsh-onion 葱welt cementing machine 贴边粘合机welt coloring machine 贴边染色机welt cutting machine 切沿条机welt fitting machine 贴边机welt footwear 加贴边的鞋welter screen 翻滚筛welter 镶边机Wepsin 三唑磷胺Werlisa 威里沙牌照相机Werner 维尔纳牌手表weskit 紧身背心Wessel silver 韦塞尔铜镍锌合金West cigarette 威狮牌香烟West ginseng 西洋参West Lake Dragon Well tea 西湖龙井茶West Lake silk umbrella 西湖绸伞West Lake silk 西湖丝绸West Lake water shield 西湖莼菜Westeeco 韦斯蒂科镍铬铁耐热合金Western king prawn 宽沟对虾Western saddle pants 西式马裤Western sand cherry 沙樱桃Western shirt 西式衬衫western style bed sheet 西式床单Western style hat 西式呢帽Western style pajamas 西式睡衣裤Western style pants 西裤Western style shirt 西式衬衫Western style shirt-waist blouse 西式衬衫上衣Western style suit 西服western tie 西式领带Western wool 美国西部羊毛Western-made shirt in plaid gingham 长方格贞咸布西式衬衫Westinghouse alloy 西屋镍铜热磁补偿合金wet spinning frame 湿纺细纱机wet air compressor 湿空气压缩机wet air pump 湿空气泵wet and dry bulb hygrometer 干湿球湿度计wet and dry bulb recording hygrometer 干湿球自记湿度计wet and dry bulb thermometer 干湿球温度计wet ball mill 湿式球磨机wet blue goat leather 山羊蓝湿革wet blue goat skin 蓝湿山羊皮wet board machine 湿式纸板机wet brush 湿刷wet chrome goat skin 铬湿山羊皮wet cleaner 湿法清洗器wet cloth 湿光布wet clutch 湿式离合器wet collector 湿式除尘器wet condenser 湿式冷凝器wet crude 含水原油wet crushing mill 湿粉碎机wet cylinder liner 湿式气缸套wet drill 湿式风钻wet dust collector 湿式收尘器wet dust separator 湿式除尘器wet electro-magnet 湿式电磁铁wet electrolytic capacitor 电解液电容器wet feeder 湿式给料机wet fiber filter 湿式纤维过滤器wet filter 湿式过滤器wet fourdrinier board machine 长网湿抄机wet frame 湿纺机wet furfural condenser 含水糖醛冷凝器wet gas meter 湿式气量计wet gas scrubber 湿法气体洗涤质量合格证书certification of fitness原材料rawmaterial底板 bottom plate 垫层 cushion侧壁 sidewall中心线center line条形基础 strip footing附件 accessories型钢 profile steel钢板 steel plate熔渣 slag飞溅 welding spatter定位焊 tacking引弧 generating of arc熄弧 quenching of arc焊道 welding bead坡口 beveled edges外观检查 visual inspection重皮 doubleskin水平方向弧度 radian in horizontal direction 成型 molding直线度 straightness accuracy焊缝角变形 welding line angular distortion 水平度 levelness铅垂度 verticality翘曲变形 buckling deformation角尺 angle square对接焊缝 butt weld母材 parent metal法兰密封面 flange sealing surface夹层interlayer表面锈蚀浓度 surface corrosion concentration挠曲变 bending deformation超声波探伤 ultrasonic testing/ ultrasonic examination压力容器 pressure vessel预制下料prefabrication baiting排版直径 set-type diameter焊缝 welding line中幅板 center plate测量方法 measuring method基准点 datum mark跳焊 skip welding允许偏差 allowable variation补强板 stiffening plate开孔 tapping对接接头 banjo fixing butt jointing角钢 angle iron安装基准圆 installation fundamental circle 吊装立柱 hoisting upright column焊接钢管 welded steel pipe向心斜拉筋 centripetal canting pull rope 带板 band plate槽钢胀圈 channel steel expansion ring环口 collar extension局部变形 local distortion环缝 circumferential weld顶板 top plate拱顶 vault顶板加强肋 stiffening rib对接 butt joint胎具 clamping fixture卷板机 plate bending rolls中心支架 center bearing bracket椭圆度 ovality等分线 bisectrix搭接宽度lap width点焊spot welding搭接焊 overlap welding对称：symmetrically螺旋爬梯cockle stairs放料阀baiting valve液位计 content gauge充水试验 filling water test错边量 unfitness of butt joint底圈 foundation ring真空度检漏 vacuum degree leak test丁字焊缝 tee welding渗透探伤 oil whiting test充水试验 filling water test内侧角焊缝接头 interior angle welding line jointfoundation settlement 基础沉降测量基准点 datum mark稳定性试验 stability test排气阀 outlet valve角钢 angle steel构件 component part机械损伤 mechanical damage缩孔 shrinkage cavityenfoldment 折迭碳钢管 carbon steel tube公称直径 nominal diameter预埋件 embedded part轴测图 axonometric drawing布置图arrangement diagram氧乙炔气割 oxyacetylene gas cutting低合金钢管low alloy steel热影响区 heat affected area 修磨polish砂轮片grinding wheel等离子plasma panel重皮 coldlap凹凸unevenness缩口necking down端面 head face倾斜偏差 dip deviation外径 external diameter砂轮grinding wheel管件 pipe casting单线图single line drawing平齐parallel and level两端 two terminals满扣 buckle螺栓紧固 bolton周边 periphery附加应力 additional stress同轴度 axiality平行度 parallelism随机 stochastic允许偏差 allowable variation重直度verticality水平度 levelness隔离盲板 blind plate氩弧焊argon arc welding压盖螺栓 gland bolt间距spacing有效期 period of validity担任 take charge of ;undertake焊条 welding rod碳钢焊条carbon steel焊丝 welding wire熔化焊 melting钢丝 steel wire气体保护焊 gas shielded arc welding 烘干drying清洗ablution制度system焊接工艺welding procedure相应corresponding手工电弧焊manual electric arc welding 手工钨极 manual tungsten electrode打底render电源power source交流alternating current焊件 weldment管壁厚度 pipe thickness对接焊缝 butt weld工件壁厚 workpiece飞溅物 splash沾污 smirch油污 oil stain细锉 smooth file铣刀 milling cutter氧化膜 oxide film脱脂处理 ungrease treatment]棉质纤维 cotton fibre丙酮acetone硫 sulfur焊剂 welding flux钢板 steel plate纵向焊缝 l0ngitudinal weld l0ngitudinal seam筒节 shell ring封头 end socket卷管 reelpipe强度试验strength test起弧arc starting穿堂风draught熔合fusion反面reverse side整体integral封堵block up焊口 weld bond医用胶布medical proof fabric高频 high frequency焊炬welding torch送气air supply焊接专业英语词汇（熔化焊）熔接fusion welding压接pressure welding焊接过程welding process焊接技术welding technique焊接工艺welding technology/procedure焊接操作welding operation焊接顺序welding sequence焊接方向direction of welding焊接位置welding position熔敷顺序build-up sequencedeposition sequence焊缝倾角weld slope/inclination of weld axis 焊缝转角weld rotation/angle of rotation平焊位置flat position of welding横焊位置horizontal position of welding立焊位置vertical position of welding仰焊位置overhead position of welding平焊downhand welding/flat position welding 横焊horizontal position welding 立焊vertical position welding仰焊overhead position welding全位置焊all position welding：熔焊时，焊件接逢所处空间位置包括平焊、横焊、仰焊等位置所进行的焊接。
焊接专业术语中英对照
焊接专业术语中英对照焊接欠缺与检验焊接欠缺welding imperfection焊接缺陷weld defect气孔blowhole/ gas pore针尖状气孔pinhole密集气孔porosity条虫状气孔wormhole裂纹crack表面裂纹surface crack咬边undercut焊瘤overlap凹坑pit烧穿burn through塌陷excessive penetration未焊透incomplete penetration/ lack of penetration未熔合lack of fusion/ incomplete fusion 未焊满incompletely filled weld根部凹陷root concavity电弧擦伤arc scratch夹渣slag inclusion夹杂物inclusion夹钨tungsten inclusion白点fish eye/ flake错边misalignment/ dislocation焊接检验试件test piece试样test specimen无损检验nondestructive test破坏检验destructive test外观检查visual examination超声波探伤ultrasonic inspection直射法超声波探伤straight beam method斜射法超声波探伤angle beam method液浸法超声波探伤immersion method射线探伤radiographic inspection/ radiographyX射线探伤X-ray radiographic inspection γ射线探伤gamma-ray inspectionX射线工业电视探伤X-ray industrial television inspection磁粉探伤magnetic particle inspection电磁探伤electromagnetic inspection/ eddy current test 探伤灵敏度flaw detection sensitivity渗透探伤penetration inspection荧光探伤flurescent penetrant inspection 着色探伤dye penetrant inspection密封性检验leak test气密性检验air tight test枕形气密检验pillow test耐压检验pressure test水压检验hydraulic test气压检验pneumatic test液晶检验liquid crystal test声发射检测acoustic emission testing面弯试验face bend testing背弯试验root bend test侧弯试验side bend test横弯试验horizontal bend test纵弯试验axial bend test压扁试验squeezing testactual weld-throat thick-ness焊缝厚度all-around weld整周焊缝all-around weld (整周焊缝)环焊缝angle butt weld斜对接焊angle weld角焊appearance of weld焊缝成形arc-seam weld电弧缝焊arc-spot weld电弧点焊arc-weld电弧焊aspect ratio of weld焊缝成形系数at weld edge在焊缝边上attachment weld连接焊缝automatic spot weld自动点焊法automatic weld自动焊接axis of a weld焊缝行南? 焊接轴线axis of weld焊缝轴线; 焊接轴线back of weld焊缝背面backing groove of weld焊缝反面坡口backing weld底焊; 底焊焊缝bare metal arc weld裸焊条电弧焊bead weld珠焊; 堆焊bead-on-plate weld堆焊焊缝beading weld凸焊beam-to-beam weld梁间焊接; 梁式引线焊接block sequence weld分段多层焊bond weld钢轨接头焊接bridge seam weld桥缝焊接; 桥线焊brize weld硬焊页脚.butt weld对接焊缝butt weld ends对头焊接端butt-weld碰焊; 平式焊接; 对头焊接butt-weld in the downhand position对接平焊butt-weld joint对头焊接butt-weld pipe mill对焊管轧机button spot weld按电钮点焊cap weld最后焊层; 盖面焊缝carbon content of weld materials焊接材料的碳含量cast-weld construction铸焊结构caulk weld填缝焊caulking weld密实焊缝chain intermittent fillet weld链式分段角焊; 并列间断角焊缝chain intermittent weld并列焊接circular weld环形焊缝circumferential weld环缝; 环焊缝cleft weld裂口焊closed weld底边无缝焊; 无间隙焊缝closed-chamber fusion weld闭室熔焊cluster weld丛聚焊缝coil weld卷板对接焊; 卷板对接焊; 板卷焊cold weld冷压接commutator-controlled weld换向控制焊接complete penetration butt weld贯穿对焊composite weld紧密焊缝; 强度密封焊缝concave filled weld凹形角焊缝concave filler weld凹角焊concave fillet weld凹面填角焊concave weld凹焊缝; 凹面焊; 凹形焊缝; 轻型焊connective weld联系焊缝continuous butt-weld mill连续式炉焊管机组continuous fillet weld连续(填)角焊缝; 连续角焊缝; 连续贴角焊continuous weld连续焊缝continuous weld process连续式炉焊管法contour weld特形焊接convex fillet weld凸角焊缝; 凸形角焊缝convex weld凸焊缝; 凸形焊缝copper weld wire包铜钢丝corner flange weld单卷边角焊缝corner weld角焊corner-flange weld卷边角焊缝; 卷边角焊缝crack of weld焊部裂纹cross weld十字交叉焊缝; 横向焊缝cross-wire weld十字焊crotch weld楔接锻接; 楔接焊接cup weld带盖板焊缝depth of weld焊接深度dissimilar weld metal不同的焊接金属; 不同金属的焊接distance between the toes of a weld焊缝宽度double groove weld双面坡口焊缝double-bevel groove weld双斜边坡口焊缝; 双斜坡口焊double-flanged butt weld双弯边对接焊缝double-V groove weld双斜边坡口焊缝; 双斜坡口焊downhand weld平焊缝duplex spot weld双点点焊接头edge joint weld边缘焊edge weld端接焊; 端接焊缝; 端面焊缝; 对边焊electric resistance weld mill电阻焊管机electric weld-pipe mill电焊管机焊接专业英语词汇（通用部分）acetylene 乙炔 ampere 电流安培angle welding 角焊 arc 电弧argon arc welding 氩弧焊接 bare electrode 光熔接条butt welding 对接焊接 camber 电弧弯曲cascade 阶叠熔接法 clad weld 被覆熔接crator 焊疤 excess metal 多余金属filler rod 焊条 fillet weld 填角焊接gas shield 气体遮蔽 groove welding 起槽熔接hand face shield 手握面罩 hard facing 硬表面堆焊jig welding 工模焊接 laser beam welding 雷射光焊接metal electrode insert gas welding MIG熔接nugget 点焊熔核overlaying 堆焊 peening of welding 珠击熔接法plug welding 塞孔熔接 positioned welding 正向熔接pressure welding 压焊 propane gas cutting 丙烷气切割页脚.pure nickel electrode 纯镍熔接条reinforcement of weld 加强焊接resist 抗蚀护膜 root running 背面熔接seam 焊缝 seaming 接合seam welding 流缝熔接 series seam welding 串联缝熔接skip welding process 跳焊法 spark 火花spot welding 点焊接 stitch welding 针角焊接stud arc welding 电弧焊接 under laying 下部焊层void 焊接空隙 weld flow mark 焊接流痕weld flush 焊缝凸起 weld line 焊接纹weld mark 焊接痕 weld penetration 熔接透入weld zone 焊接区 welding 焊接welding bead 焊接泡 welding direction 焊接方向welding distortion 焊接变形 welding flux 焊剂welding ground 电熔接地 welding interval 焊接周期welding stress 熔接应变 welding torch 熔接气炬welding electrode production line 电焊条生产线welding electrode 焊条welding fixture 焊接夹具welding generator 电焊机welding goggles 焊工护目镜welding gun 焊枪welding helmet 电焊帽welding inspection ruler 焊接检验尺welding machine 焊接机welding mill 焊管机welding motor generator 电动焊接发电机welding nozzle 焊嘴welding paste 焊接药膏welding pipe 焊接管welding powder 焊粉welding rectifier 焊接整流器welding robot 焊接机器人welding rod extrusion press 焊条挤压机welding rod with acidic coating 酸性焊条welding rod with alkaline coating 碱性焊条welding rod 焊条welding simulator 焊接模拟器welding stainless electrode 不锈电焊条welding steel tube 焊接钢管welding tin billet 焊锡棒料welding tongs 焊接夹钳welding torch 焊炬welding transformer 电焊变压器welding unit 焊机welding wire machine 焊线机welding wire 焊丝welding-cutting hose 熔焊及切割胶管welding-cutting tool 焊割具welding-rod core 焊条芯welding-seam cleaner 焊缝清理机weldless pipe 无缝管weldless steel tube 无缝钢管well borer 凿井机well counter 井式计数器well deck vessel 井形甲板船well drill 钻井机well platform 钻井平台well rig 钻井机well testing truck 试井车well thermometer 井温计well tube filter 井管滤管well type tempering electric furnace 井式回火电炉well winch 矿井绞车well-logging probe 测井探头well-type counter 井型计数器Wella Balsam Conditioner 威娜宝护发素Wella Balsam shampoo 威娜宝香波Wellene 韦纶聚酯短纤维wellhead acid preventer 井口防酸器wellington 惠灵顿防雨呢Wellingtons 长筒皮靴Welltite 韦纶泰特聚丙烯和聚乙烯单丝Welsbach's alloy 韦尔斯巴赫发火合金Welsh flannel 威尔士法兰绒Welsh wool 威尔士粗羊毛welsh-onion stalk 葱白welsh-onion 葱welt cementing machine 贴边粘合机welt coloring machine 贴边染色机welt cutting machine 切沿条机welt fitting machine 贴边机welt footwear 加贴边的鞋页脚.welter screen 翻滚筛welter 镶边机Wepsin 三唑磷胺Werlisa 威里沙牌照相机Werner 维尔纳牌手表weskit 紧身背心Wessel silver 韦塞尔铜镍锌合金West cigarette 威狮牌香烟West ginseng 西洋参West Lake Dragon Well tea 西湖龙井茶West Lake silk umbrella 西湖绸伞West Lake silk 西湖丝绸West Lake water shield 西湖莼菜Westeeco 韦斯蒂科镍铬铁耐热合金Western king prawn 宽沟对虾Western saddle pants 西式马裤Western sand cherry 沙樱桃Western shirt 西式衬衫western style bed sheet 西式床单Western style hat 西式呢帽Western style pajamas 西式睡衣裤Western style pants 西裤Western style shirt 西式衬衫Western style shirt-waist blouse 西式衬衫上衣Western style suit 西服western tie 西式领带Western wool 美国西部羊毛Western-made shirt in plaid gingham 长方格贞咸布西式衬衫Westinghouse alloy 西屋镍铜热磁补偿合金wet spinning frame 湿纺细纱机wet air compressor 湿空气压缩机wet air pump 湿空气泵wet and dry bulb hygrometer 干湿球湿度计wet and dry bulb recording hygrometer 干湿球自记湿度计wet and dry bulb thermometer 干湿球温度计wet ball mill 湿式球磨机wet blue goat leather 山羊蓝湿革wet blue goat skin 蓝湿山羊皮wet board machine 湿式纸板机wet brush 湿刷wet chrome goat skin 铬湿山羊皮wet cleaner 湿法清洗器wet cloth 湿光布wet clutch 湿式离合器wet collector 湿式除尘器wet condenser 湿式冷凝器wet crude 含水原油wet crushing mill 湿粉碎机wet cylinder liner 湿式气缸套wet drill 湿式风钻wet dust collector 湿式收尘器wet dust separator 湿式除尘器wet electro-magnet 湿式电磁铁wet electrolytic capacitor 电解液电容器wet feeder 湿式给料机wet fiber filter 湿式纤维过滤器wet filter 湿式过滤器wet fourdrinier board machine 长网湿抄机wet frame 湿纺机wet furfural condenser 含水糖醛冷凝器wet gas meter 湿式气量计wet gas scrubber 湿法气体洗涤质量合格证书certification of fitness原材料rawmaterial底板 bottom plate垫层 cushion侧壁 sidewall中心线center line条形基础 strip footing附件 accessories型钢 profile steel钢板 steel plate熔渣 slag飞溅 welding spatter定位焊 tacking引弧 generating of arc熄弧 quenching of arc焊道 welding bead坡口 beveled edges外观检查 visual inspection重皮 doubleskin水平方向弧度 radian in horizontal direction 成型 molding直线度 straightness accuracy焊缝角变形 welding line angular distortion 水平度 levelness铅垂度 verticality翘曲变形 buckling deformation角尺 angle square页脚.对接焊缝 butt weld母材 parent metal法兰密封面 flange sealing surface夹层interlayer表面锈蚀浓度 surface corrosion concentration挠曲变 bending deformation超声波探伤 ultrasonic testing/ ultrasonic examination压力容器 pressure vessel预制下料prefabrication baiting排版直径 set-type diameter焊缝 welding line中幅板 ? center plate测量方法 measuring method基准点 datum mark跳焊 skip welding允许偏差 allowable variation补强板 stiffening plate开孔 tapping对接接头 banjo fixing butt jointing角钢 angle iron安装基准圆 installation fundamental circle 吊装立柱 hoisting upright column焊接钢管 welded steel pipe向心斜拉筋 centripetal canting pull rope 带板 band plate槽钢胀圈 channel steel expansion ring环口 collar extension局部变形 local distortion环缝 circumferential weld顶板 top plate拱顶 vault顶板加强肋 stiffening rib对接 butt joint胎具 clamping fixture卷板机 plate bending rolls中心支架 center bearing bracket椭圆度 ovality等分线 bisectrix搭接宽度lap width点焊spot welding搭接焊 overlap welding对称：symmetrically螺旋爬梯cockle stairs放料阀baiting valve 液位计 content gauge充水试验 filling water test错边量 unfitness of butt joint底圈 foundation ring真空度检漏 vacuum degree leak test丁字焊缝 tee welding渗透探伤 oil whiting test充水试验 filling water test侧角焊缝接头 interior angle welding line jointfoundation settlement 基础沉降测量基准点 datum mark?稳定性试验 stability test排气阀 outlet valve角钢 angle steel构件 component part机械损伤 mechanical damage缩孔 shrinkage cavityenfoldment 折迭碳钢管 carbon steel tube公称直径 nominal diameter预埋件 embedded part轴测图 axonometric drawing布置图arrangement diagram氧乙炔气割 oxyacetylene gas cutting低合金钢管low alloy steel热影响区 heat affected area修磨polish砂轮片grinding wheel等离子plasma panel重皮 coldlap凹凸unevenness缩口necking down端面 head face倾斜偏差 dip deviation外径 external diameter砂轮grinding wheel管件 pipe casting单线图single line drawing平齐parallel and level两端 two terminals满扣 buckle螺栓紧固 bolton周边 periphery附加应力 additional stress页脚.同轴度 axiality平行度 parallelism随机 stochastic允许偏差 allowable variation重直度verticality水平度 levelness隔离盲板 blind plate氩弧焊argon arc welding压盖螺栓 gland bolt间距spacing有效期 period of validity担任 take charge of ;undertake焊条 welding rod碳钢焊条carbon steel焊丝 welding wire熔化焊 melting钢丝 steel wire气体保护焊 gas shielded arc welding 烘干drying清洗ablution制度system焊接工艺welding procedure相应corresponding手工电弧焊manual electric arc welding 手工钨极 manual tungsten electrode打底render电源power source交流alternating current焊件 weldment管壁厚度 pipe thickness对接焊缝 butt weld工件壁厚 workpiece飞溅物 splash沾污 smirch油污 oil stain细锉 smooth file铣刀 milling cutter氧化膜 oxide film脱脂处理 ungrease treatment]棉质纤维 cotton fibre丙酮acetone硫 sulfur焊剂 welding flux钢板 steel plate纵向焊缝 l0ngitudinal weld l0ngitudinal seam筒节 shell ring 封头 end socket卷管 reelpipe强度试验strength test起弧arc starting穿堂风draught熔合fusion反面reverse side整体integral封堵block up焊口 weld bond医用胶布medical proof fabric高频 high frequency焊炬welding torch送气air supply焊接专业英语词汇（熔化焊）熔接fusion welding压接pressure welding焊接过程welding process焊接技术welding technique焊接工艺welding technology/procedure焊接操作welding operation焊接顺序welding sequence焊接方向direction of welding焊接位置welding position熔敷顺序build-up sequencedeposition sequence焊缝倾角weld slope/inclination of weld axis 焊缝转角weld rotation/angle of rotation平焊位置flat position of welding横焊位置horizontal position of welding立焊位置vertical position of welding仰焊位置overhead position of welding平焊downhand welding/flat position welding 横焊horizontal position welding立焊vertical position welding仰焊overhead position welding全位置焊all position welding：熔焊时，焊件接逢所处空间位置包括平焊、横焊、仰焊等位置所进行的焊接。
焊接术语中英文对照
高锰钢堆焊焊条：high manganese steel surfacing electrode
管状焊条：flux-cored electrode
钛铁矿形焊条：ilmenite type electrode
氧化铁型焊条：iron oxide type electrode/ high iron oxide type electrode
高纤维素型焊条：high cellulose (type) electrode
石墨型焊条：graphite type electrode
SAW ——Submerged Arc Welding——埋弧焊
FCAW ——flux cored arc welding——药芯焊丝电弧焊
FCW-G ——gas-shielded flux cored arc welding——气保护药芯焊丝电弧焊
FCW-S——self-shielded flux cored arc welding——自保护药芯焊丝电弧焊
高效率焊条：high efficiency electrode
铁粉焊条：iron powder electrode
重力焊条：gravity electrode
立向下焊条：electrode for vertical down position welding
水下焊条：underwater welding electrode
碱性焊条：basic electrode/ lime type covered electrode
低氢型焊条：low hydrogen type electrode
焊接专业术语中英对照
荧光探伤flurescent penetrant inspection 焊接专业术语中英对照着色探伤dye penetrant inspection密封性检验焊接欠缺与检验 leak test气密性检验air tight test 焊接欠缺welding imperfection枕形气密检验pillow test 焊接缺陷weld defect耐压检验pressure test 气孔blowhole/ gas pore水压检验pinhole hydraulic test 针尖状气孔气压检验密集气孔porosity pneumatic test液晶检验wormhole liquid crystal test条虫状气孔声发射检测裂纹crackacoustic emission testing面弯试验表面裂纹surface crack face bend testing背弯试验undercut root bend test 咬边侧弯试验焊瘤overlap side bend test 横弯试验pit凹坑horizontal bend test纵弯试验axial bend test 烧穿burn through压扁试验excessive penetrationsqueezing test塌陷actual weld-throat thick-ness未焊透incomplete penetration/ lack of 焊缝厚度all-around weld整周焊缝penetrationall-around weld (整周焊缝)环焊缝未熔合lack of fusion/ incomplete fusion angle butt weld斜对接焊未焊满incompletely filled weldangle weld角焊根部凹陷root concavityappearance of weld焊缝成形电弧擦伤arc scratcharc-seam weld夹渣slag inclusion 电弧缝焊arc-spot weldinclusion电弧点焊夹杂物arc-weld电弧焊夹钨tungsten inclusionaspect ratio of weld焊缝成形系数白点fish eye/ flakeat weld edge在焊缝边上错边misalignment/ dislocationattachment weld焊接检验连接焊缝automatic spot weld自动点焊法试件test pieceautomatic weld自动焊接试样test specimenaxis of a weld无损检验nondestructive test 焊缝行南? 焊接轴线axis of weld破坏检验destructive test 焊缝轴线; 焊接轴线back of weld外观检查visual examination焊缝背面backing groove of weld焊缝反面坡口超声波探伤ultrasonic inspectionbacking weld底焊; straight beam method 直射法超声波探伤底焊焊缝bare metal arc weld裸焊条电弧焊斜射法超声波探伤angle beam method bead weld珠焊; 堆焊液浸法超声波探伤immersion methodbead-on-plate weld堆焊焊缝射线探伤radiographic inspection/beading weldradiography凸焊beam-to-beam weld梁间焊接; 梁式引线焊接射线探伤XX-ray radiographic inspectionblock sequence weld分段多层焊gamma-ray inspection 射线探伤γbond weld钢轨接头焊接X-ray industrial 射线工业电视探伤Xbridge seam weld桥缝焊接; television inspection桥线焊brize weldmagnetic particle inspection 磁粉探伤硬焊butt weldelectromagnetic inspection/ eddy 电磁探伤对接焊缝butt weld ends对头焊接端current testbutt-weld碰焊flaw detection sensitivity 探伤灵敏度; 平式焊接; 对头焊接对接平焊butt-weld in the downhand positionpenetration inspection渗透探伤．金属的焊接butt-weld joint对头焊接焊缝宽 distance between the toes of a weldbutt-weld pipe mill对焊管轧机 button spot weld按电钮点焊度双面坡口焊缝double groove weldcap weld最后焊层; 盖面焊缝双carbon content of weld materials焊接材料的; weld双斜边坡口焊缝double-bevel groove斜坡口焊碳含量双弯边对接焊缝double-flanged butt weldcast-weld construction铸焊结构双斜坡; weld双斜边坡口焊缝填缝焊caulk weld double-V groove口焊caulking weld密实焊缝 chain intermittent fillet 平焊缝链式分段角焊; downhand weldweldduplex spot weld双点点焊接头并列间断角焊缝edge joint weld并列焊接边缘焊 chain intermittent weldedge weld端接焊circular weld环形焊缝 ; 端接焊缝; 端面焊缝; 对边焊 circumferential weld环缝; 环焊缝electric resistance weld mill电阻焊管机 cleft weld裂口焊electric weld-pipe mill无间隙焊缝电焊管机 closed weld底边无缝焊;闭室熔焊closed-chamber fusion weld焊接专业英语词汇（通用部分） cluster weld丛聚焊缝acetylene 乙炔 ampere 电流安培卷板对接焊coil weld卷板对接焊; ; 板卷焊angle welding 角焊 arc 电弧 cold weld冷压接argon arc welding commutator-controlled weld氩弧焊接 bare electrode 换向控制焊接光熔接条complete penetration butt weld贯穿对焊butt welding 强度密封焊缝composite weld紧密焊缝; 对接焊接 camber 电弧弯曲cascade 阶叠熔接法 clad weld concave filled weld凹形角焊缝被覆熔接crator 焊疤 excess metal 多余金属 concave filler weld凹角焊filler rod 焊条 fillet weld 填角焊接 concave fillet weld凹面填角焊gas shield 轻型气体遮蔽 groove welding 起槽熔; weldconcave 凹焊缝; 凹面焊凹形焊缝;接焊hand face shield 手握面罩 hard facing connective weld联系焊缝硬表面堆焊连续式炉焊管机组continuous butt-weld milljig welding (continuous fillet weld连续填工模焊接连续 laser beam welding 雷; )角焊缝射光焊接角焊缝; 连续贴角焊metal electrode insert gas welding MIG熔接 continuous weld连续焊缝nugget 点焊熔核连续式炉焊管法continuous weld processoverlaying 堆焊特形焊接 peening of welding 珠击熔contour weld接法convex fillet weld凸形角焊缝; 凸角焊缝plug welding 凸形焊缝塞孔熔接 positioned welding ; 凸焊缝convex weld正向熔接copper weld wire 包铜钢丝pressure welding corner flange weld单卷边角焊缝压焊 propane gas cutting丙烷气切割角焊corner weldpure nickel electrode 卷边角焊缝; corner-flange weld卷边角焊缝纯镍熔接条reinforcement of weld 焊部裂纹crack of weld加强焊接resist 抗蚀护膜 root running 背面熔接横向焊缝; cross weld十字交叉焊缝seam 十字焊cross-wire weld焊缝 seaming 接合seam welding 楔接焊接; crotch weld楔接锻接流缝熔接 series seam welding 串联缝熔接带盖板焊缝cup weldskip welding process 跳焊法 spark 火花焊接深度depth of weld针角焊 stitch welding 点焊接spot welding 不同; 不同的焊接金属dissimilar weld metal焊割具 welding-cutting tool 接 under laying 下焊条芯welding-rod core stud arc welding 电弧焊接焊缝清理机部焊层 welding-seam cleaner 无缝管weldless pipe void 焊接空隙 weld flow mark 焊接流痕weldless steel tube 焊接纹无缝钢管weld flush 焊缝凸起 weld lineweld mark 焊接痕 weld penetration 熔接透入 well borer 凿井机well counter 井式计数器焊接区 welding 焊接 weld zonewell deck vessel 井形甲板船焊接 welding bead 焊接泡 welding direction well drill 方向钻井机well platform 焊接变形 welding flux 钻井平台 welding distortionwell rig 钻井机焊剂well testing truck 试井车welding ground 电熔接地 welding interval well thermometer 井温计焊接周期well tube filter 井管滤管熔接welding stress 熔接应变 welding torch well type tempering electric furnace 井式气炬回火电炉weldingelectrode production line 电焊条生well winch 矿井绞车产线well-logging probe 焊条welding electrode 测井探头well-type counter 焊接夹具井型计数器 welding fixtureWella Balsam Conditioner 威娜宝护发素welding generator 电焊机Wella Balsam shampoo 威娜宝香波 welding goggles 焊工护目镜Wellene welding gun 韦纶聚酯短纤维焊枪wellhead acid preventer 井口防酸器 welding helmet 电焊帽wellington 惠灵顿防雨呢 welding inspection ruler 焊接检验尺Wellingtons 长筒皮靴welding machine 焊接机Welltite 韦纶泰特聚丙烯和聚乙烯单丝焊管机welding millWelsbach's alloy 韦尔斯巴赫发火合金 welding motor generator 电动焊接发电机Welsh flannel 威尔士法兰绒welding nozzle 焊嘴Welsh wool 威尔士粗羊毛 welding paste 焊接药膏welsh-onion stalk 葱白焊接管welding pipewelsh-onion welding powder 焊粉葱welt cementing machine 贴边粘合机焊接整流器welding rectifierwelt coloring machine 贴边染色机 welding robot 焊接机器人welt cutting machine 切沿条机焊条挤压机welding rod extrusion press welt fitting machine 酸性焊条贴边机 welding rod with acidic coating welt footwear welding rod with alkaline coating 加贴边的鞋碱性焊条welter screen welding rod 焊条翻滚筛welter welding simulator 镶边机焊接模拟器Wepsin welding stainless electrode 不锈电焊条三唑磷胺Werlisa 威里沙牌照相机焊接钢管welding steel tubeWerner 维尔纳牌手表焊锡棒料welding tin billetweskit 紧身背心焊接夹钳welding tongsWessel silver 韦塞尔铜镍锌合金 welding torch 焊炬West cigarette 电焊变压器welding transformer 威狮牌香烟West ginseng welding unit 焊机西洋参West Lake Dragon Well tea 西湖龙井茶焊线机welding wire machine West Lake silk umbrella welding wire 焊丝西湖绸伞西湖丝绸West Lake silk 熔焊及切割胶管welding-cutting hosewet fourdrinier board machine 西湖莼菜长网湿抄机 West Lake water shield wet frame 湿纺机Westeeco 韦斯蒂科镍铬铁耐热合金wet furfural condenser 含水糖醛冷凝器Western king prawn 宽沟对虾wet gas meter 湿式气量计 Western saddle pants 西式马裤wet gas scrubber 湿法气体洗涤 Western sand cherry 沙樱桃质量合格证书certification of fitness 西式衬衫 Western shirt原材料western style bed sheet 西式床单 rawmaterial底板 bottom plate Western style hat 西式呢帽垫层西式睡衣裤 cushion Western style pajamas侧壁Western style pants 西裤 sidewall中心线center lineWestern style shirt 西式衬衫条形基础 strip footing 西式衬衫Western style shirt-waist blouse附件 accessories 上衣型钢Western style suit 西服 profile steel钢板 western tie 西式领带 steel plate熔渣 slagWestern wool 美国西部羊毛飞溅长方格 welding spatter Western-made shirt in plaid gingham定位焊贞咸布西式衬衫 tacking引弧西屋镍铜热磁补偿合金 generating of arc Westinghouse alloy熄弧湿纺细纱机wet spinning frame quenching of arc焊道湿空气压缩机 welding bead wet air compressor坡口wet air pump 湿空气泵 beveled edges外观检查干湿球湿度计 visual inspection wet and dry bulb hygrometer 重皮干湿wet and dry bulb recording hygrometer doubleskin水平方向弧度 radian in 球自记湿度计horizontal direction成型 molding干湿球温度计wet and dry bulb thermometer直线度wet ball mill 湿式球磨机 straightness accuracy焊缝角变形 welding line angular distortion 山羊蓝湿革wet blue goat leather水平度蓝湿山羊皮 levelness wet blue goat skin铅垂度湿式纸板机wet board machine verticality翘曲变形 buckling deformation wet brush 湿刷角尺铬湿山羊皮wet chrome goat skin angle square对接焊缝wet cleaner 湿法清洗器 butt weld母材湿光布wet cloth parent metal法兰密封面 flange sealing surface wet clutch 湿式离合器夹层interlayer 湿式除尘器wet collector表面锈蚀浓度湿式冷凝器 surface corrosion wet condenserconcentrationwet crude 含水原油挠曲变wet crushing mill 湿粉碎机 bending deformation超声波探伤 wet cylinder liner 湿式气缸套 ultrasonic testing/ ultrasonic examination湿式风钻wet drill压力容器湿式收尘器wet dust collector pressure vessel预制下料湿式除尘器wet dust separator prefabrication baiting排版直径wet electro-magnet 湿式电磁铁 set-type diameter焊缝 welding line 电解液电容器wet electrolytic capacitor中幅板湿式给料机wet feeder ? center plate测量方法湿式纤维过滤器wet fiber filter measuring methoddatum mark基准点湿式过滤器wet filtershrinkage cavity skip welding缩孔跳焊允许偏差 allowable variation enfoldment 折迭 carbon steel tube 碳钢管补强板 stiffening platenominal diameter tapping公称直径开孔 embedded part对接接头 banjo fixing butt jointing 预埋件 axonometric drawing angle iron轴测图角钢arrangement diagram安装基准圆 installation fundamental circle 布置图氧乙炔气割 hoisting upright column oxyacetylene gas cutting 吊装立柱低合金钢管焊接钢管welded steel pipelow alloy steel热影响区 heat affected area 向心斜拉筋 centripetal canting pull rope 修磨 band platepolish带板砂轮片槽钢胀圈 channel steel expansion ring grinding wheel等离子plasma panel 环口 collar extension重皮 local distortion coldlap 局部变形凹凸环缝 circumferential weld unevenness缩口necking down 顶板 top plate端面 vaulthead face拱顶倾斜偏 stiffening rib 顶板加强肋差 dip deviation外径 butt jointexternal diameter 对接砂轮胎具 clamping fixturegrinding wheel管件卷板机 plate bending rollspipe casting单线 center bearing bracket 中心支架图single line drawing平齐 ovality parallel and level 椭圆度两端等分线 bisectrix two terminals满扣搭接宽度lap width buckle螺栓spot welding点焊紧固 bolton周边 peripheryoverlap welding 搭接焊附加 symmetrically 对称：应力 additional stress 同轴螺旋爬梯cockle stairs 度 axiality平行 baiting valve 放料阀度 parallelism随机 stochasticcontent gauge液位计允许偏 filling water test 充水试验差 allowable variation重直度错边量 unfitness of butt joint verticality水平度 foundation ring底圈 levelness隔离 vacuum degree leak test 真空度检漏盲板 blind plate氩弧丁字焊缝 tee welding焊argon arc welding压盖螺栓 oil whiting test 渗透探伤 gland bolt间距spacingfilling water test充水试验有效期 interior angle welding line 内侧角焊缝接头 period of validity担任jointtake charge of ;undertake焊条foundation settlement 基础沉降 welding rod碳钢 datum mark 测量基准点焊条carbon steel焊丝?welding wire熔化焊 stability test 稳定性试验 melting钢丝 steel wireoutlet valve 排气阀气体保护焊 angle steel 角钢 gas shielded arc welding烘干 component part构件dryingablution清洗 mechanical damage 机械损伤．焊接顺序制度systemwelding sequence焊接方向welding procedure direction of welding 焊接工艺焊接位置相应correspondingwelding position熔敷顺序build-up sequence 弧焊manual electric arc welding 手工电deposition sequence manual tungsten electrode 极手工钨焊缝倾角weld render打底slope/inclination of weld axis焊缝转角power sourceweld rotation/angle of rotation 电源平焊位置交流alternating current flat position of welding横焊位置horizontal position of welding 焊件 weldment立焊位置 pipe thickness vertical position of welding 管壁厚度仰焊位置对接焊 butt weld overhead position of welding缝平焊厚 workpiecedownhand welding/flat position welding 工件壁横焊物 splash沾污 smirch horizontal position welding 飞溅立焊 oil stain 油污vertical position welding仰焊overhead position welding细锉 smooth file全位置焊all position welding：熔焊时，焊件 milling cutter 铣刀接逢所处空间位置包括平焊、横焊、仰焊等位置膜 oxide film氧化所进行的焊接。
常用焊接中英文词典(DOC)
常用术语中英文字典Raw materials:alumina铝土bauxite铝矿土log大圆棒billet小圆棒（铝棒）butt废料（挤压切头）Magnesium镁Silicon硅Iron铁Copper铜Manganese锰Chromium铬extruabilitystrength-to-weight ratio quenching conductivity Equipment:log conveyorlog furnacebillet furnacesolvus tempreture solidus tempreturelog shearbillet transveyorpress loaderramdummy block 可挤压性强度重量比淬火可导电性，导电率设施：大圆棒运输机大圆棒加热炉铝棒加热炉溶线温度固线温度圆棒剪铝棒运输机挤压机托料架机械手挤压杆压饼（挤压垫）containercontainer linerrunout tablefront platenmain cylinderDie:die ringdiebackerbolstershim (sub-bolster) feederpocket(cavity of feeder) hollow diesemi-hollow die 盛锭筒盛锭筒内衬（内套）输出台前板主缸模具：模套模具模垫前垫后垫导流板袋式平模空心模半空心模solid die aperture (pocket) die cap mandrel porthole pancakebridgespiderhorse shoetool carrierdie bearing reliefdie ovenradiant oven infrared oven 平模孔隙下模（母模）上模（公模）孔式分流模园盘式模桥式模蜘蛛模马蹄形止口模座工作带空刀模具加热炉辐射炉红处线炉lead-out table quench boxstanding-wave cooling mist coolingair coolingwebportpullertransfer beltscooling beltstretchertail headpower headclampscrossover belts 导出台淬火槽过水槽冷却水雾冷却风冷桥进料孔牵引机传递台冷却带（台）拉直机（调直机）固定端活动端夹头（拉直机）传递带staging and saw:锯切工作台和锯staging area锯切工作台saw锯batching belt配置传递带saw gauge锯切定尺台supervisory control system(SCS)监督控制系统programmable logic可编过程控制器controller(PLC)aging oven时效炉Processtemperature rise挤压时的上涨温度exit temperature出口温度tearing扯裂container wall挤压筒筒壁shear zoneexit temp. measurement temp. stickthermocouple temp. probe pyrometeratomic structurequench rateprecipitateMagnesium Silicide crystals intersperse(dispersion) preservetempercritical quench ratetemper designations recoveryaluminum oxide 出口温度丈量测温笔热电偶探测针高温计原子构造淬火率积淀硅化镁晶体分别保持状态临界淬火率状态定义成品率氧化铝scrap费料productivity measurement生产效率的评估press efficiency挤压机效率weight per person-hour单位时间人均成品率internal scrap produced费品率rejected and returned material退货率ratioproduction and maintenance停机时间downtimeOEE (overall equipment整个设施效率effectiveness)quality rate可销售产品率performance rate实质出品率availability rate挤压机利用率Quality质量defectsvernier(calipers)feeler gaugego-no-go gauges protractorsquareWebster hardness tester back end condition blisterbowbroken diesaw burrchattercorrosion-pitting corrosion water stain 缺点千分尺塞尺专用测型仪角规矩尺，丁字尺韦氏硬度钳挤压尾部条件气泡，沙眼曲折模具破坏锯毛刺振痕腐化点水迹die line模痕faltness deviation 不平（不平淬火，拉伸过分，模具错误）hook侧面曲折inclusion 因模具内售杂质而型材含杂质kink因搬运造成的严重变形lamination迭层（因铸锭有裂缝，或模具含杂质）flow line模痕carbon mark石墨痕handling mark碰伤roll mark转动痕stop mark断痕stretcher jam mark拉抻机夹痕traffic mark碰伤orange peel桔皮pickup粘铝A-DAbsolute deviation,绝对离差Absolute number,绝对数Absolute residuals,绝对残差Acceleration array,加快度立体阵Acceleration in an arbitrary direction,随意方向上的加快度Acceleration normal,法向加快度Acceleration space dimension,加快度空间的维数Acceleration tangential,切向加快度Acceleration vector,加快度向量Acceptable hypothesis,可接受假定Accumulation,积累Accuracy,正确度Actual frequency,实质频数Adaptive estimator,自适应预计量Addition,相加Addition theorem,加法定理Additivity,可加性Adjusted rate,调整率Adjusted value,校订当Admissible error,允许偏差Aggregation,齐集性Alternative hypothesis,备择假定Among groups,组间Amounts,总量Analysis of correlation,有关剖析Analysis of covariance,协方差剖析Analysis of regression,回归剖析Analysis of time series,时间序列剖析Analysis of variance,方差剖析Angular transformation,角变换ANOVA（ analysis of variance）,方差剖析ANOVA Models, 方差剖析模型Arcing, 弧/ 弧旋Arcsine transformation,反正弦变换Area under the curve,曲线面积AREG , 评估从一个时间点到下一个时间点回归有关时的偏差ARIMA, 季节和非季节性单变量模型的极大似然预计Arithmetic grid paper,算术格纸Arithmetic mean,算术均匀数Arrhenius relation,艾恩尼斯关系Assessing fit,拟合的评估Associative laws,联合律Asymmetric distribution,非对称分布Asymptotic bias,渐近偏倚Asymptotic efficiency,渐近效率Asymptotic variance,渐近方差Attributable risk,归因危险度Attribute data,属性资料Attribution,属性Autocorrelation,自有关Autocorrelation of residuals,残差的自有关Average, 均匀数Average confidence interval length,均匀置信区间长度Average growth rate,均匀增加率Bar chart,条形图Bar graph,条形图Base period,基期Bayes' theorem , Bayes定理Bell-shaped curve,钟形曲线Bernoulli distribution,伯努力分布Best-trim estimator,最好切尾预计量Bias, 偏性Binary logistic regression,二元逻辑斯蒂回归Binomial distribution,二项分布Bisquare, 双平方Bivariate Correlate,二变量有关Bivariate normal distribution,双变量正态分布Bivariate normal population,双变量正态整体Biweight interval,双权区间Biweight M-estimator,双权 M预计量Block, 区组 / 配伍组BMDP(Biomedical computer programs), BMDP统计软件包Boxplots,箱线图 /箱尾图Breakdown bound,崩溃界 / 崩溃点Canonical correlation,典型有关Caption,纵标目Case-control study,病例比较研究Categorical variable,分类变量Catenary,悬链线Cauchy distribution,柯西分布Cause-and-effect relationship,因果关系Cell, 单元Censoring,终检Center of symmetry,对称中心Centering and scaling,中心化和定标Central tendency,集中趋向Central value,中心值CHAID -χ2 Automatic Interaction Detector,卡方自动交互检测Chance, 机会Chance error,随机偏差Chance variable,随机变量Characteristic equation,特点方程Characteristic root,特点根Characteristic vector,特点向量Chebshev criterion of fit,拟合的切比雪夫准则Chernoff faces,切尔诺夫脸谱图Chi-square test,卡方查验 / χ2查验Choleskey decomposition,乔洛斯基分解Circle chart,圆图Class interval,组距Class mid-value,组中值Class upper limit,组上限Classified variable,分类变量Cluster analysis,聚类剖析Cluster sampling,整群抽样Code, 代码Coded data, 编码数据Coding, 编码Coefficient of contingency,列联系数Coefficient of determination,决定系数Coefficient of multiple correlation,多重有关系数Coefficient of partial correlation,偏有关系数Coefficient of production-moment correlation,积差有关系数Coefficient of rank correlation,等级有关系数Coefficient of regression,回归系数Coefficient of skewness,偏度系数Coefficient of variation,变异系数Cohort study,队列研究Column, 列Column effect,列效应Column factor,列要素Combination pool,归并Combinative table,组合表Common factor,共性因子Common regression coefficient,公共回归系数Common value, 共同值Common variance,公共方差Common variation,公共变异Communality variance,共性方差Comparability,可比性Comparison of bathes,批比较Comparison value,比较值Compartment model, 分部模型Compassion,伸缩Complement of an event,补事件Complete association,完整正有关Complete dissociation,完整不有关Complete statistics,齐备统计量Completely randomized design,完整随机化设计Composite event,联合事件Composite events,复合事件Concavity, 凹性Conditional expectation,条件希望Conditional likelihood,条件似然Conditional probability,条件概率Conditionally linear,依条件线性Confidence interval,置信区间Confidence limit,置信限Confidence lower limit,置信下限Confidence upper limit,置信上限Confirmatory Factor Analysis ,考证性因子剖析Confirmatory research,证明性实验研究Confounding factor,混淆要素Conjoint,联合剖析Consistency,相合性Consistency check,一致性查验Consistent asymptotically normal estimate,相合渐近正态预计Consistent estimate,相合预计Constrained nonlinear regression,受拘束非线性回归Constraint,拘束Contaminated distribution,污染分布Contaminated Gausssian,污染高斯分布Contaminated normal distribution,污染正态分布Contamination,污染Contamination model,污染模型Contingency table,列联表Contour,界限线Contribution rate,贡献率Control,比较Controlled experiments,比较实验Conventional depth,惯例深度Convolution,卷积Corrected factor,校订因子Corrected mean,校订均值Correction coefficient,校订系数Correctness,正确性Correlation coefficient,有关系数Correlation index,有关指数Correspondence,对应Counting,计数Counts,计数/ 频数Covariance,协方差Covariant,共变Cox Regression, Cox回归Criteria for fitting,拟合准则Criteria of least squares,最小二乘准则Critical ratio,临界比Critical region,拒绝域Critical value,临界值Cross-over design,交错设计Cross-section analysis,横断面剖析Cross-section survey,横断面检查Crosstabs ,交错表Cross-tabulation table,复合表Cube root,立方根Cumulative distribution function,分布函数Cumulative probability,累计概率Curvature,曲率/ 曲折Curvature,曲率Curve fit ,曲线拟和Curve fitting,曲线拟合Curvilinear regression,曲线回归Curvilinear relation,曲线关系Cut-and-try method,试试法Cycle, 周期Cyclist,周期性D test, D查验Data acquisition,资料采集Data bank,数据库Data capacity,数据容量Data deficiencies,数据缺少Data handling,数据办理Data manipulation,数据办理Data processing,数据办理Data reduction,数据减少Data set,数据集Data sources,数据根源Data transformation,数据变换Data validity,数占有效性Data-in,数据输入Data-out,数据输出Dead time,阻滞期Degree of freedom,自由度Degree of precision,精细度Degree of reliability,靠谱性程度Degression, 递减Density function,密度函数Density of data points,数据点的密度Dependent variable,应变量 / 依变量 / 因变量Dependent variable,因变量Depth, 深度Derivative matrix,导数矩阵Derivative-free methods,无导数方法Design, 设计Determinacy,确立性Determinant,队列式Determinant,决定要素Deviation, 离差Deviation from average,离均差Diagnostic plot,诊疗图Dichotomous variable,二分变量Differential equation,微分方程Direct standardization,直接标准化法Discrete variable,失散型变量DISCRIMINANT, 判断Discriminant analysis,鉴别剖析Discriminant coefficient,鉴别系数Discriminant function,鉴别值Dispersion, 分布 / 分别度Disproportional,不行比率的Disproportionate sub-class numbers,不行比率次级组含量Distribution free,分布没关性 / 免分布Distribution shape,分布形状Distribution-free method,随意分布法Distributive laws,分派律Disturbance, 随机扰动项Dose response curve,剂量反响曲线Double blind method,双盲法Double blind trial,双盲试验Double exponential distribution,双指数分布Double logarithmic,双对数Downward rank,降秩Dual-space plot,对偶空间图DUD, 无导数方法Duncan's new multiple range method,新复极差法/Duncan新法E-LEffect,实验效应Eigenvalue,特点值Eigenvector,特点向量Ellipse,椭圆Empirical distribution,经验分布Empirical probability,经验概率单位Enumeration data,计数资料Equal sun-class number,相等次级组含量Equally likely,等可能Equivariance,同变性Error,偏差/错误Error of estimate,预计偏差Error type I,第一类错误Error type II,第二类错误Estimand, 被估计Estimated error mean squares,预计偏差均方Estimated error sum of squares,预计偏差平方和Euclidean distance,欧式距离Event,事件Event,事件Exceptional data point,异样数据点Expectation plane,希望平面Expectation surface,希望曲面Expected values,希望值Experiment,实验试验抽样Experimental unit,试验单位Explanatory variable,说明变量Exploratory data analysis,探究性数据剖析Explore Summarize,探究- 纲要Exponential curve,指数曲线Exponential growth,指数式增加EXSMOOTH,指数光滑方法Extended fit,扩大拟合Extra parameter,附带参数Extrapolation,外推法Extreme observation,尾端观察值Extremes, 极端值 / 极值F distribution, F分布F test, F查验Factor,要素/ 因子Factor analysis,因子剖析Factor Analysis,因子剖析Factor score,因子得分Factorial,阶乘Factorial design,析因试验设计False negative,假阴性False negative error,假阴性错误Family of distributions,分布族Family of estimators,预计量族Fanning,扇面Fatality rate,病死率Field investigation,现场检查Field survey,现场检查Finite population,有限整体Finite-sample,有限样本First derivative,一阶导数First principal component,第一主成分First quartile,第一四分位数Fisher information,费雪信息量Fitted value,拟合值Fitting a curve,曲线拟合Fixed base,定基Fluctuation,随机起伏Forecast,展望Four fold table,四格表Fourth, 四分点Fraction blow,左边比率Fractional error,相对偏差Frequency,频次Frequency polygon,频数多边图Frontier point,界线点Function relationship,泛函关系Gamma distribution,伽玛分布Gauss increment,高斯增量Gaussian distribution,高斯分布 / 正态分布Gauss-Newton increment, 高斯 - 牛顿增量General census,全面普查GENLOG (Generalized liner models),广义线性模型Geometric mean,几何均匀数Gini's mean difference,基尼均差GLM (General liner models),通用线性模型Goodness of fit,拟和优度 / 配合度Gradient of determinant,队列式的梯度Graeco-Latin square,希腊拉丁方Grand mean, 总均值Gross errors,重要错误Gross-error sensitivity,大错敏感度Group averages,分组均匀Grouped data,分组资料Guessed mean, 假定均匀数Half-life,半衰期Hampel M-estimators,汉佩尔 M预计量Happenstance,有时事件Harmonic mean,调解均数Hazard function,风险均数Hazard rate,风险率Heading,标目Heavy-tailed distribution, Hessian array,海森立体阵Heterogeneity,不一样质Heterogeneity of variance, Hierarchical classification, Hierarchical clustering method,重尾分布方差不齐组内分组系统聚类法High-leverage point,高杠杆率点HILOGLINEAR,多维列联表的层次对数线性模型Hinge,折叶点Histogram,直方图Historical cohort study,历史性队列研究Holes, 空洞HOMALS,多重响应剖析Homogeneity of variance,方差齐性Homogeneity test,齐性查验Huber M-estimators,休伯 M预计量Hyperbola,双曲线Hypothesis testing,假定查验Hypothetical universe,假定整体Impossible event,不行能事件Independence,独立性Independent variable,自变量Index, 指标 / 指数Indirect standardization,间接标准化法Individual,个体Inference band,推测带Infinite population,无穷整体Infinitely great,无量大Infinitely small,无量小Influence curve,影响曲线Information capacity,信息容量Initial condition,初始条件Initial estimate,初始预计值Initial level,最先水平Interaction,交互作用Interaction terms,交互作用项Intercept,截距Interpolation,内插法Interquartile range,四分位距Interval estimation,区间预计Intervals of equal probability,等概率区间Intrinsic curvature,固有曲率Invariance,不变性Inverse matrix,逆矩阵Inverse probability,逆概率Inverse sine transformation,反正弦变换Iteration,迭代Jacobian determinant,雅可比队列式Joint distribution function,分布函数Joint probability,联合概率Joint probability distribution,联合概率分布K means method,逐渐聚类法Kaplan-Meier, 评估事件的时间长度Kaplan-Merier chart, Kaplan-Merier图Kendall's rank correlation, Kendall等级有关Kinetic,动力学Kolmogorov-Smirnove test,柯尔莫哥洛夫-斯米尔诺夫查验Kruskal and Wallis test, Kruskal及 Wallis查验 / 多样本的秩和查验 /H 查验Kurtosis,峰度Lack of fit,失拟Ladder of powers,幂阶梯Lag, 滞后Large sample, 大样本Large sample test,大样本查验Latin square,拉丁方Latin square design,拉丁方设计Leakage,泄露Least favorable configuration,最不利构形Least favorable distribution,最不利分布Least significant difference,最小明显差法Least square method,最小二乘法Least-absolute-residuals estimates,最小绝对残差预计Least-absolute-residuals fit,最小绝对残差拟合Least-absolute-residuals line,最小绝对残差线Legend, 图例L-estimator, L预计量L-estimator of location,地点 L 预计量L-estimator of scale,尺度 L 预计量Level, 水平Life expectance,预期希望寿命Life table,寿命表Life table method,生命表法Light-tailed distribution,轻尾分布Likelihood function,似然函数Likelihood ratio,似然比line graph,线图Linear correlation,直线有关Linear equation,线性方程Linear programming,线性规划Linear regression,直线回归Linear Regression,线性回归Linear trend,线性趋向Loading,载荷Location and scale equivariance,地点尺度同变性Location equivariance,地点同变性Location invariance,地点不变性Location scale family,地点尺度族Log rank test,时序查验Logarithmic curve,对数曲线Logarithmic normal distribution,对数正态分布Logarithmic scale,对数尺度Logarithmic transformation,对数变换Logic check,逻辑检查Logistic distribution,逻辑斯特分布Logit transformation, Logit变换LOGLINEAR,多维列联表通用模型Lognormal distribution,对数正态分布Lost function,损失函数Low correlation,低度有关Lower limit,下限Lowest-attained variance,最小可达方差LSD, 最小明显差法的简称Lurking variable,潜伏变量。
焊接术语中英对照
电阻焊 resistance welding (RW)点焊 spot welding；resistance spot welding凸焊 projection welding缝焊 seam welding滚点焊 roll-spot welding连续点焊 stitch welding多点焊 multiple spot welding手压点焊 push welding；poke welding单面点焊 indirect spot welding双面点焊 direct spot welding脉冲点焊 pulsation spot welding；multiple-impulse welding串联点焊 series spot welding多点凸焊 multiple projection welding频道进缝焊 step-by-step seam welding压平缝焊 mash seam welding串联缝焊 series seam welding对接缝焊 butt seam welding；foil-butt seam电阻对焊 upset butt welding闪光对焊 flash butt welding (FBW)储能焊 stored energy welding电容储能点焊 condenser discharge spot welding高频电阻焊 high frequency resistance welding冲击电阻焊 percussion welding胶接点焊 spot weld-bonding；weld-bonding 塑料喷涂 plastic spraying陶瓷喷涂 ceramic spraying喷熔 spray-fusing表面粗糙化处理 surface roughening电火花拉毛 electrospark roughening抛锚效应 anchoring喷涂层 spray-fused coating喷熔层 spray-fused coating结合层 bond coating；under coating工作层 work coating结合强度 adhesive strength涂层强度 strength of coating封孔处理 sealing封孔剂 sealant喷涂率 spray rate沉积效率 deposition efficiency孔隙率 porosity喷涂材料 spraying material自熔剂合金粉末 self-fluxing alloy powder 喷炬（枪） spray torch；热切割 thermal cutting (TC)气割 gas cutting；oxygen cutting氧溶剂切割 powder cutting氧-石英砂切割 quartz powder cutting闪光 flashing；flash过梁 bridge；lintel顶锻 upsetting；upset夹紧力 clamping force顶锻力 upsetting force；upset force电极压力 electrode force；electrode pressure电极滑移 electrode skid焊接循环 welding cycle预压时间 squeeze time锻压时间 forge-delay time；forge time焊接通电时间（电阻焊） welding time (resistance welding)预热时间 preheat time加热时间 heat time冷却时间 cool time间歇时间 quench time；chill time回火时间 temper time维持时间 hold time休止时间 off time闪光时间 flash time；flashing time顶锻时间 upset time；upsetting time有电顶锻时间 upset current time无电顶锻时间 upset current-off time闪光速度 flashing speed闪光电流 flashing current；flash current顶锻电流 upset current预热电流 preheat current 电弧切割 arc cutting氧气电弧切割 oxy-arc cutting空气电弧切割 air arc cutting等离子弧切割 plasma arc cutting (PAC)空气等离子弧切割 air plasma arc cutting氧等离子切割 oxygen plasma arc cutting水再压缩空气等离子弧切割 air plasma water injection arc cutting双层气流等离子弧切割 dual gas plasma arc cutting；shielded gas plasma arc cutting激光切割 laser cutting(LC)；laser beam cutting电子束切割 electron beam cutting喷气激光切割 gas jet laser cutting碳弧切割 carbon arc cutting水下切割 underwater cutting喷水式水下电弧切割 waterjet method underwater arc cutting氧矛切割 oxygen lancing；oxygen lance cutting溶剂氧切割 powder lancing手工气割 manual oxygen cutting自动气割 automatic oxygen cutting仿形切割 shape cutting数控切割 NC (numerical-control) cutting快速切割 high-speed cutting垂直切割 square cut叠板切割 stack cutting坡口切割 beveling；bevel cutting回火电流 temper current调伸长度 initial overhange；extension 总留量 total allowance闪光留量 flash allowance顶锻留量 upset allowance顶锻速度 upset speed电极接触面 electrode contact surface 贴合面 faying surface焊点 welding spot熔核 nugget熔核直径 diameter of nugget塑性金属环区 corona bond焊透率 penetration rate压痕 indentation压痕深度 depth of indentation压深率 indentation ratio翘离 sheet separation缩孔 shrinkage cavity胡须 intrusion电极粘损 electrode pick up喷溅 splash/ expulsion毛刺 fin飞边 upset metal/ fin焊点距 weld spacing/ spot weld spacing 边距 edge distance分流 shunt current 碳弧气割 carbon arc air gouging火焰气刨 flame gouging火焰表面清理 scarfing氧熔剂表面修整 powder washing预热火焰 preheat flame预热氧 preheat oxygen切割氧 cutting oxygen/ cutting stream切割速度 cutting speed切割线 lone of cut/ cut line切割面 face of cut/ cut face切口 kerf切口上缘 cutting shoulder切口宽度 kerf width后拖量 drag切割面平面度 evenness of cutting surface/ planeness of cutting surface割纹深度 depth of cutting veins/ stria depth切割面质量 quality of cut face上缘熔化度 shoulder meltability/ melting degree of shoulder切口角 kerf angle缺口 notch挂渣 adhering slag结瘤 dross割炬 cutting torch/ cutting blowpipe/ oxygen-fuel gas cutting torch割枪 cutting gun割嘴 cutting nozzle/ cutting tip接触电阻 contact resistance电阻焊机 resistance welding machine点焊机 spot welding machine多点焊机 multiple spot welding machine移动式点焊机 portable spot welding machine缝焊机 seam welding machine纵横两用缝焊机 universal seam welder对焊机 butt resistance welding machine凸焊机 projection welding machine三相低频焊机 three phase low frequency welder 二次整流电阻焊机 direct current resistance welder secondary rectification电容储能电阻焊机 condenser discharge resistance welder电容储能点焊机 condenser type spot welder/ capacitor spot welding machine工频电阻焊机 mains frequency resistance welding machine低频电阻焊机 frequency converter resistance welding machine高频焊机 high frequency induction welder逆变式电阻焊机 inverter type resistance welding machine全波阻焊电源 full wave resistance welding power source斩波阻焊电源 chopped wave resistance welding power source旋转焊接变压器 rotary welding transformer 快速割嘴 divergent nozzle/ high-speed nozzle表面割炬 gouging blowpipe水下割炬 under-water cutting blowpipe水下割条 electrode for under-water cutting粉剂罐 powder dispenser数控切割机 NC cutting machine门式切割机 flame planer光电跟踪切割机 photo-electric tracing cutting火焰切管机 pipe flame cutting machine磁轮式气割机 gas cutting machine with magnetic wheels焊接结构 welded structure/ welded construction 焊件 weldment焊接部件 weld assembly组装件 built-up member接头设计 joint design焊接应力 welding stress焊接瞬时应力 transient welding stress焊接残余应力 welding residual stress热应力 thermal stress收缩应力 contraction stress局部应力 local stress拘束应力 constraint stress固有应力 inherent stress固有应变区 inherent strain zone残余应力测定 residual stress analysis逐层切割法Sach’s method点焊钳 spot welding headC形点焊钳 C-type welding head/ C-type gunX形点焊钳 pincer spot welding head/ pliers spot welding head断续器 contactor同步断续器 synchronous contactor异步断续器 non-synchronous contactor程序控制器 sequencer程序时间调节器 sequencer timer电极臂 arm电极握杆 electrode holder电极台板 backup die/ bolster电极水冷管 electrode cooling tube电极头 electrode tip电极帽 electrode cap锥头电极 truncated tip electrode平头电极 flat tip electrode尖头电极 pointed tip electrode球面电极 radius tip electrode偏心电极 offest electrode直电极 straight electrode弯电极 cranked electrode双弯电极 double cranked (swannecked) electrode 滚轮电极 circular electrode/ welding wheel斜棱滚轮电极 bevelled wheel顶锻机构 upsetting mechanism电极总行程 total electrode stroke X射线衍射法 X-ray stress analysis小孔释放法 Mathar method固有应变法 inherent strain method消除应力 stress relieving局部消除应力 local stress relieving应力重分布 stress redistribution退火消除应力 stress relieving by annealing温差拉伸消除应力 low temperature stress relieving 机械拉伸消除应力 mechanical stress relieving应力松弛 stress relaxation焊接变形 welding deformation焊接残余变形 welding residual deformation局部变形 local deformation角变形 angular distortion自由变形 free deformation收缩变形 contraction deformation错边变形 mismatching deformation挠曲变形 deflection deformation波浪变形 wave-like deformation火焰矫正 flame straightening反变形 backward deformation焊接力学 welding mechanics断裂力学 fracture mechanics弹塑性断裂变形 elasto-plastic fracture mechanics 线弹性断裂力学 linear elastic fracture mechanics 延性断裂 ductile fracture脆性断裂 brittle fracture工作行程 operational stroke辅助行程 electrode travel/ electrode stroke臂间距离 horn spacing/ throat opening电极臂伸出长度 arm extension摩擦焊 friction welding (FW)转速 friction speed摩擦压力 friction pressure/ heating pressure摩擦转矩 friction torque摩擦时间 friction time摩擦变形量 burn-off length摩擦变形速度 burn-off rate停车时间 stopping time顶锻变形量 forge length顶锻变形速度 forge rate摩擦表面 friction surface储能摩擦焊 fly-wheel type friction welding径向摩擦焊 radial friction welding扩散焊 diffusion welding (DW)过渡液相扩散焊 transient liquid phase diffusion welding热等静压扩散焊 hot isotatic pressure diffusion welding热轧扩散焊 roll diffusion welding扩散缝焊 seam diffusion welding超塑成形扩散焊 supperplastic forming diffusion bounding隔离剂 buttering material爆炸焊 explosive welding (EW) 应力腐蚀开裂 stress corrosion cracking热应变脆化 hot straining embrittlement临界裂纹尺寸 critical crack size裂纹扩展速率 crack propagation rate裂纹张开位移（COD）crack opening displacement 拘束度 restraint intensity拘束系数 restraint coefficient应变速率 strain rate断裂韧度 fracture toughness应力强度因子 stress intensity factor临界应力强度因子 critical stress intensity factors应力腐蚀临界应力强度因子 critical stress intensity factor of stress corrosion crackingJ积分 J-integration罗伯逊止裂试验 Robertson crack arrest testESSO试验 ESSO test双重拉伸试验 doucle tension test韦尔斯宽板拉伸试验Well’s wide plate test帕瑞斯公式 Paris formula断裂分析图 fracture analysis diagram焊接车间 welding shop焊接工作间 welding booth焊接工位 welding post/ welding station焊接环境 welding surroundings焊工 welder电焊工 manual arc welder气焊工 gas welder爆炸点焊 explosive spot welding爆炸线焊 explosive line welding多层板爆炸焊 explosive welding of multiplayer plates多层管爆炸焊 explosive welding of multiplayer tubes覆板（覆管） cladding plat (tube)/ flyer plate (tube) 基板（基管） base plate(tube)/ parent plate (tube) 保护层 buffer/ protector基础 base预置角 preset angle间距 initial stand-off/ spacing装药量 explosive load装药密度 charge density/ loading density质量比 mass ratio平行法 parallel plate configuration角度法 preset angle configuration均匀布药 average arranging explosive梯形布药 gradient arranging explosive爆炸焊参数 explosive welding parameters初始参数 initial parameters动态参数 dynamic parameters界面参数 interface parameters爆轰速度 detonation velocity覆板速度 cladding plate velocity碰撞点 impact point碰撞点速度 velocity of the impact point 焊接检验员 weld inspector焊工培训 welders training焊工模拟训练器 trainer of synthetic weld焊工考试 welder qualification test焊工合格证 welder qualification/ welder qualified certification钢板预处理 steel plate pretreatment喷沙 sand blast喷丸 shot blast矫正 straighten开坡口 bevelling (of the edge)/ chanfering装配 assembly/ fitting安装 erect刚性固定 rigid fixing装配焊接顺序 sequence of fitting and welding焊接工艺评定 welding procedure qualification焊接工艺规程 welding procedure specification焊接工艺试验 welding procedure test焊接工艺卡 welding procedure card工序 operational sequence焊接材料消耗定额 welding consumables quota 焊接工时定额 welder-hour quota清渣 slag removal清根 back gouging/ back chipping锤击 peening返修次数 number of rewelding焊接工作台 welding bench弯折角 bending angle碰撞角 collision angle碰撞压力 impact pressure格尼能 Gurney energy垂直碰撞 normal impact倾斜碰撞 oblique impact/ inclined impact对称碰撞 symmetrical impact来流 upper stream出流 down stream再入射流 re-entrant jet自清理 oneself cleaning结合区 bond zone平面结合 plane bond波状结合 wave-like bond界面波长 length of the interfacial wave界面波幅 amplitude of the interfacial wave熔化层 molten layer熔化袋 molten pocket雷管区 detonator zone边界效应 edge effect焊接性窗口 weldability windows焊着率 ratio of welding area起爆方法 method of initiation内爆法 internal explosion process外爆法 external explosion process半圆柱试验法 semi-cylinder experiment method 超声波焊 ultrasonic welding (UW) 装焊平台 welding platen电磁平台 electromagnetic platen焊接翻转机 welding tilter焊接回转台 floor turnable positioner焊接变位机 positioner焊接滚轮架 turning rolls焊接操作机 manpulator焊工升降台welder’s lifting platform焊接夹具 welding jig/ fixture磁力夹紧器 magnetic jig螺旋推撑器 screw operated tensioning unit焊丝盘绕机 welding wire coiler焊条压涂机 welding electrode extrusion press 红外线加热器 infra-red heater干燥箱 dryer焊条保温筒 thermostat for electrode流量计 flow meterCO2预热器 CO2 heaterCO2干燥器 CO2 desiccator焊接电缆 welding cable电缆夹头 welding connector地线 earth lead地线夹头 earth clamp焊接参数记录仪 welding parameter recorder 焊缝检测规 weld gauge喷嘴通针 tip cleaner测温笔 tempil stick超声波点焊 ultrasonic spot welding超声波缝焊 ultrasonic seam welding超声波点焊机 ultrasonic spot welder超声波缝焊机 ultrasonic seam welder冷压焊 cold pressure welding (CPW)热压焊 hot pressure welding热轧焊 hot roll welding旋弧压力焊 rotating arc pressure welding埋弧压力焊 submerged arc pressure welding电渣压力焊 electroslag pressure welding气压焊 gas pressure welding锻焊 forge-welding/ blacksmith welding磁力脉冲焊 magnetic-pulse welding硬钎焊 brazing软钎焊 soldering烙铁钎焊 iron soldering火焰钎焊 torch brazing/ torch soldering热风钎焊 hot gas soldering感应钎焊 induction brazing电阻钎焊 resistance brazing接触反应钎焊 contact-reaction brazing电弧钎焊 arc brazing浸渍钎焊 dip brazing/ dip soldering盐浴钎焊 saltbath dip brazing (soldering)金属浴钎焊 molten metal bath dip brazing炉中钎焊 furnace brazing/ furnace soldering保护气氛钎焊 brazing in controlled atmosphere 敲渣锤 chipping hammer焊接衬垫 backing/ welding backing保留垫板 fusible backing/ permanent backing 临时垫板 temporary backing焊剂垫 flux backing惰性气体衬垫 inert-gas backing引弧板 run-on tab/ end tab/ starting weld tab 引出板 run-off tab/ end tab定位板 strong-back加强勒 stiffener嵌条 insert套环 ferrule面罩 helmet滤光镜片 filter glass/ welding glass防护镜片 cover glass/ plain glass气焊眼镜 welding goggles焊接机器人 welding robot点焊机器人 spot welding robot弧焊机器人 arc welding robot切割机器人 cutting robot焊接机器人生产线 robot line for welding焊接机器人工作站 welding robot station机器人运动自由 degree of free for robot机器人工作空间 robot working space轨迹重复精度 path repeatability点位重复精度 PTP repeatability焊接专家系统 welding expert system真空钎焊 vacuum brazing蒸气钎焊 vapor phase soldering超声波钎焊 ultrasonic soldering扩散钎焊 diffusion brazing波峰钎焊 flow soldering/ wave soldering分级钎焊 step brazing/ step soldering不等间隙钎焊 brazing with the unparalleled clearance红外线钎焊 infra-red brazing (soldering)光束钎焊 light soldering (brazing)激光钎焊 laser brazing (soldering)电子束钎焊 electron beam brazing钎接焊 braze-welding钎料 brazing filler metal/ solder硬钎料 brazing filler metal软钎料 solder (m)自钎剂钎料 self-fluxing brazing alloy/ self-fluxing filler metal活性钎料 active filler metal/ active metal brazing alloy成形钎料 preformed filler metal/ solder preform 非晶态钎料 amorphous filler metal粉状钎料 powdered filler metal钎料膏 braze cream/ braze paste/ solder cream/ solder paste药皮钎料 flux coated brazing(soldering)rod层状钎料 sandwich filler metal药芯钎料丝 flux-cored colder wire 焊接机器人示数 welding robot play back焊接图象识别 pattern recognition for welding焊接图象处理 welding image processing计算机辅助焊接工艺设计 computer-aided welding process programming (CAWPP)计算机辅助焊接结构设计 computer-aided design for welding structure焊接烟尘 weld fume焊接发尘量 total amount of fumes焊接烟尘浓度 weld fume concentration焊接烟尘容限浓度 threshold limit values of weld fume (TLV)焊接发尘速率 weld fume emission rate焊接有害气体 welding toxic gases/ weld harmful gases 标定卫生空气需要量 nominal hygienic air requirement 焊工尘肺 pheumocomsis of welder焊工锰中毒 chronic occupational manganese poisoning of welder焊工氟中毒 fluorosis of welder焊工金属烟热 metal fume fever of welder电光性眼炎 eye-flash (arc eye)电光性皮炎 electro-photo dermatitis电弧紫外线灼伤 ultraviolet ray burn防电击装置 voltage reducing device除尘装置 dust collection device焊工手套 welding gloves护脚 welding spats防护鞋 shielding shoes敷钎料板 clad brazing sheet钎剂 brazing flux；soldering flux气体钎剂 gas flux反应钎剂 reaction flux松香钎剂 colophony flux；rosin flux钎剂膏 flux paste阻流剂 stopping-off agent钎剂活性 flux activity钎剂活性温度范围 activation temperature range of flux钎剂热稳定性 thermal stability of flux钎焊过程 brazing (soldering) process钎焊操作 brazing (soldering) operation（焊接网 ）工艺镀层 technological coating钎焊面 faying face钎缝间缝 joint gap；joint clearance钎焊参数 brazing process variables钎焊温度 brazing temperature钎焊时间 brazing time钎焊保温时间 holding time of brazing钎缝 brazing seam；soldering seam钎缝界面区 interfacial region钎缝金属 brace metal钎角 fillet钎焊接头 braced joint；soldered joint平面搭接头 joggled lap joint；flush lap joint 焊接欠缺 welding imperfection焊接缺陷 weld defect气孔 blowhole/ gas pore针尖状气孔 pinhole密集气孔 porosity条虫状气孔 wormhole裂纹 crack表面裂纹 surface crack咬边 undercut焊瘤 overlap凹坑 pit烧穿 burn through塌陷 excessive penetration未焊透 incomplete penetration/ lack of penetration 未熔合 lack of fusion/ incomplete fusion未焊满 incompletely filled weld根部凹陷 root concavity电弧擦伤 arc scratch夹渣 slag inclusion夹杂物 inclusion夹钨 tungsten inclusion白点 fish eye/ flake错边 misalignment/ dislocation试件 test piece试样 test specimen无损检验 nondestructive test破坏检验 destructive test搭接对接接头 butt and lap joint搭接T 形接头 lapped T-joint ；flanged T-joint 锁缝接头 folded joint平面锁缝接头 lick side seam joint ；flat lock seam joint锁缝角接接头 lock corner joint ；corner double seam 嵌入T 形接头 inset T joint T 形管接头 branch T saddle joint 套管接头 socket joint外喇叭口套管接头 flare tube fitting 扩口套管接头 spigot joint 钎焊性 brazability ；solderability 润湿性 wettability润湿角 wetting angle ；contact angle 铺展性 spreadability铺展系数 spread factor ；coefficient of spreading 钎着率 brazed rate脱钎 de-brazing ；de-soldering 润湿称量试验 wetting balance test 铺展性试验 spreadability test 填缝性试验 clearance fillability test 未钎透 incomplete penetration 虚钎 cold soldered joint 钎料熔析 liquation of filler metal 溶蚀 erosion钎料流失 brazing filler metal erosion 钎剂夹杂 flux inclusion外观检查 visual examination 超声波探伤 ultrasonic inspection 直射法超声波探伤 straight beam method斜射法超声波探伤 angle beam method 液浸法超声波探伤 immersion method射线探伤 radiographic inspection/ radiography X 射线探伤 X-ray radiographic inspection γ射线探伤 gamma-ray inspectionX 射线工业电视探伤 X-ray industrial television inspection磁粉探伤 magnetic particle inspection电磁探伤 electromagnetic inspection/ eddy current test 探伤灵敏度 flaw detection sensitivity 渗透探伤 penetration inspection 荧光探伤 flurescent penetrant inspection 着色探伤 dye penetrant inspection 密封性检验 leak test 气密性检验 air tight test 枕形气密检验 pillow test 耐压检验 pressure test 水压检验 hydraulic test 气压检验 pneumatic test 液晶检验 liquid crystal test声发射检测 acoustic emission testing 面弯试验 face bend testing 背弯试验 root bend test 侧弯试验 side bend test晶间渗入 intergranular penetration波峰钎焊机 wave soldering machine冷壁真空钎焊炉 cold wall type vacuum brazing 热壁真空钎焊炉 hot wall type vacuum brazing furnace钎焊盒 brazing retort钎剂涂敷器 fluxer钎炬 brazing (soldering) blowpipe喷灯 brazing lamp烙铁 solder iron热喷涂 thermal spraying火焰喷涂 flame spraying电弧喷涂 electric arc spraying等离子喷涂 plasma spraying高频感应喷涂 high frequency spraying气体爆燃式喷涂 detonation flame spraying 横弯试验 horizontal bend test 纵弯试验 axial bend test压扁试验 squeezing testinert-gas-arc-welding 惰性气体弧焊,惰性气体保护焊hard-to-weld 难焊接的可焊性差的weld-all-over 全周焊接，全部焊接V-weld V形坡口(对接)焊缝butt-weld 以对头焊接接合welding 焊接法, 定位焊接U-weld U形(坡口)焊接x-weld X型(坡口)焊缝cast-weld 铸焊,浇注焊接doubleU-weld 双U形坡口焊（焊接网welded rod 焊接篦条；焊接篦条,焊接筛条weld nugget 点焊焊点；点焊焊点,点焊熔核welding terminals 电焊机接线端，电焊机接线端子weld pass 焊接道次；焊接道次,焊接次数scarf weld 斜面焊接, 两端搭接焊, 嵌接焊scarf welding 两端搭接焊, 嵌焊, 斜面焊接atomic-hydrogen welding 核氢焊,核氢焊机,氢原子电弧焊weld area 焊接部位；焊接部位,焊缝区linde welding 林德钢管对焊法,林德钢管对焊法flush weld 齐平焊缝,平焊,削平补强的焊缝 ）tack-weld 点焊，定位焊all-welded 全焊体全焊的oxy-welding (氧)气焊butt-welded 对接焊接的press-welding 压焊，冷焊spot-weld vt 点焊l.w.|lap-welded 搭接焊的 lap-welded 搭接焊的space-welding 间隔焊接weld-edgewise 沿边焊forge-welding 锻焊welding-lead 电焊引线crotch-weld 楔接焊接weld-nut 焊接螺母arc-welding 电弧焊接weld-time 焊接时间welding-position 焊接位置intermittent-weld 断续焊接automatic-welding 自动焊接welding-stress 焊接应力welding-flame 焊接火焰welding-symbol 焊接符号welding-equipment 焊接设备weld-spacing 焊接间距butt-resistance-welding 电阻对焊welding-sequence 焊接顺序autogenous-welding 氩氧锂接welding burner 焊工喷燃器,焊焊枪嘴,焊接喷灯resistance welding 电阻焊，电阻焊接，接触焊接bridge welding 加搭板对接点焊,加搭板对接滚焊welding die 接触板；接触板,凸焊用电极flux-cored welding 管状焊丝电弧焊,药芯焊丝电弧焊welding process 焊接法，焊接过程，焊接方式electropercussive welding 电冲击焊, 电接触焊, 电点焊pressure welding 压焊，压力焊接，加压焊接weld preparation 开焊接坡口，焊接接头准备welding ground 电焊(接)地线，焊接地线unionare welding 磁性焊剂二氧化碳气体爆ず附樱weld together 焊接起来,使结合在一起arc welding 电炉焊接,电弧焊；电弧焊backhand welding 反手焊接,右向焊,后退式气焊intermittent welding 断续焊，间断焊，断续焊接scarf weld 斜面焊接,两端搭接焊,嵌接焊welding powder 焊粉；焊粉,粉状焊接熔剂welding point 焊拉点；焊拉点,焊接位置closed-butt weld 密接对接焊缝,无间隙对接焊缝welding pressure 电极压力,镦粗压力，顶锻压力stick welding 气体保护金属极电弧焊,粘结焊commutator-controlled welding 换向控制焊接,可控整流器焊接horizontal-rolled-position welding 横向滚动位置焊接,滚动水平焊torch welding 气炬焊接，气炬焊扫，气焊welded joint 焊缝，焊接接头，焊接接合tight-weld 密封焊性weld-length 焊缝长度welding-symbols 焊接符号welding-current 焊接电流welding-ground 电焊地线weld-size 焊接尺寸explosive-welding 爆炸焊接welding-source 焊接电源friction-welding 摩擦焊接seam-welding 缝焊,滚焊ultrasonic-welding 超声波焊接bead-weld 珠焊,堆焊horizontal-welding 横焊,平焊forge-welding 锻接,锻焊welding-flux 焊剂,焊料welding-transformer 焊接变压器weld-penetration 熔深,熔透blacksmith-welding 锻接,锻焊forge-weld 锻接,锻焊enclosed-welding 强制成形焊welding 焊接法,粘结weld 焊接,焊接点welding-head 焊头,烙铁头fillet-welding 填角焊,条焊butt-welding 对焊,对接焊forward-welding 前进焊,左焊butt-weld 对接焊,对焊welding generator 电焊发电机，焊接用发电机mash welding 交叉焊条式压薄点焊,压薄滚焊edge weld 边缘焊缝，端焊接，端焊缝field weld 安装焊接装配焊接工地焊接Welding Association 德国焊接技术协会[联邦德国] welding rectifier 电焊整流器，焊接整流器cascade welding 阶梯形多层焊, 串级叠置焊welding station 焊接室；焊接室,焊接台meshed weld 压边焊接焊缝,啮合焊接焊缝single-fillet weld 单边角接焊缝,单面填角焊缝plasma-arc welding 等离子弧焊接,等离子电弧焊girth welding 环缝焊接,环形焊缝焊接TIG welding 钨极惰性气体保护电弧焊TlG-arc welding 钨极惰性气体保护电弧焊air-hydrogen welding 空气-氢焊接submerged-arc welding 焊剂层下焊接beading weld 窄焊缝,珠焊welding bench 焊接工专weld throat 焊缝厚度hf welding 高频焊接welding engineering 焊接工程welding section 焊接断面inverted weld 凹面焊缝jump-welded pipe 对缝焊管intermittent weld 断续焊缝butt-welded tube 对缝焊管forged weld 锻接焊缝block-sequence-welding 多段多层焊接法welded-joint 锻焊缝,锻接头seal-weld 密封焊,封闭焊percussion-welding 冲击焊,储能焊butt-seam-welding 对缝焊,对线焊welding-torch 焊接吹管,焊矩weld-zone 焊接区,焊接处thermit-welding 铝热焊,热剂焊tack-welding 点固焊,平头焊接fusion-welding 熔焊接,熔融焊接backstep-welding 后退焊接,分段退焊welding-force 阻焊加压,电极压力edge-weld 边缘焊接,端接焊接flash-welding 闪光焊接,闪光对焊upset-welding 电阻对焊,镦压焊接welded-pipe 锻接管,压力焊接管backhand-welding 后退焊接,反手焊接tack-weld 定位焊点,点固焊点discontinuous-welding 断续焊接,间断焊接as-welded 熔接状态,焊接状态welding-shop 焊接车间,焊接工场welding-leads 电焊引线,焊机电缆线pulsation-welding 脉冲焊接,多脉冲焊接strength-weld 高强度焊接,强密焊接fillet-welding-joint 填角焊缝接头,角焊接头parallel-welding 直接焊珠焊接,焊珠焊接weld 熔焊,结合；焊接,焊skip weld 间断焊缝welding characteristics 焊接特性weld flaw 焊接缺陷welding deformations 焊接变形welded frame 焊接骨架profection welding 凸出焊接welding department 焊接车间welding strees 焊接应力helical welding 螺旋焊接groove-welded joint 坡口焊缝welding characteristic 焊接性能blacksmiths weld 锻焊接头weld failure 焊缝开裂pipe welding 管路焊接weld hardening 焊接硬化backup weld 封底焊缝weld spatter 焊接飞溅weld metallurgy 焊接冶金back-step welding 分段退焊welding tangs 焊接夹钳frection welding 摩擦焊roll welding 滚压焊butt-welded seam 对焊缝union-melt welding 埋弧焊welding clamp 电焊夹头all-around weld 整周焊缝welding factor 焊接系数welded 熔焊,结合；焊接的welded 熔焊(结合)；焊接的manual-welding 手焊接resistance-welding 电阻焊welding-machine 焊接管weld-line 焊接线welding-heat 焊接热welding-operator 焊接工block-welding 块焊接welding-rod 焊条welding 焊接fusion-weld 熔焊slot-welding 槽焊gas-welding 气焊spot-welding 点焊skip-welding 跳焊smith-welding 锻焊lap-welding 搭焊plug-welding 塞焊flush-weld 平焊flat-welding 平焊manual-weld 手焊electric-welding 电焊spot-weld 焊点slot-weld 槽焊pressure-welding 压焊projection-weld 凸焊weld dressing 清理焊烽welding rules 焊接规则weld crosswise 交叉焊接double-vee weld X形焊缝flash butt-welding 闪光对接焊one-pass weld 联合筑路机full-penetration weld 全焊透焊缝welding gutter 焊管拉模welding crack 焊接裂纹weld cracking 焊缝破裂backing weld 底层焊接backing welding 底层焊接hand welding 手工焊接weld wire 包铜钢丝welding code 焊接规范welding cycle 焊接周期ripple weld 鳞纹焊缝welding mask 焊接面罩weld cycle 焊接周期weld jig 焊接夹具welding atmosphere 焊接气氛welding amperage 焊接电流welding voitage 焊接电压multilayer welding 多层焊接overhead weld 仰焊焊缝welding data 施焊工艺条件flash butt-weld 闪光对接焊缝mig welding 惰性气体保护金属极电极弧焊；米克焊接；金属惰性气体保护焊接,惰性气体保护金属极焊接machine welding 机械焊接，机械化焊接，自动焊接，自动焊，机械(化)焊（焊接网 ）mag welding 活性气体保护金属极焊接；MAG焊,活性气体保护电弧焊welding inspector 焊接工段检验员；焊接工段检验员,焊件检查员tack weld 点住焊，定位焊，定位焊点，定位焊接，钉焊mesh weld 压边焊接焊缝；压边焊接焊缝,啮合焊接焊缝welding head 烙铁头，焊枪，(自动电焊机的)机头，焊机头aircomatic welding 自动调弧氩弧焊, 惰性气体保护金属极弧焊welding outfit 焊接配备；焊接设备,焊机，焊接装置shallow weld 浅熔焊焊缝；浅熔焊焊缝,末焊透焊缝aircomatic welding 自动调弧氩弧焊,惰性气体保护金属极弧焊site welding 安装焊接,工地焊接,现场焊接,安装焊接heliarc welding 海利亚克法焊接；赫利焊接,氦气保welding precaution 焊接预防措施structural welding 建筑结构焊接oxy-hydrogen welding 氢氧焰焊接incomplete-penetration weld 未焊透焊缝sagged weld 成凹陷焊缝directarc welding 直接电弧焊multiple-row weld 多排焊接头girth weld 环形焊缝around weld 周围焊缝gas-welding flame 气焊火焰puddle welding 堆焊,熔焊hammer weld 锻接,锻程plasma welding 等离子焊接welding metallurgy 焊接冶金学welded break 捍接断裂处welding mill 焊管机welding grade 焊接级blacksmith's weld 锻焊缝gas-welding heat 气焊热welding pool 焊接池two-axis welding 双轴焊welding leads 焊接铅vibration welding 振动焊tape welding 带焊接welding shaft 焊接轴gas welded 气焊的welded bridge 焊接桥护焊接sealing weld 封底焊缝，密封焊缝，密封焊，封底焊rod welding 焊条焊,特种成分的焊条作为焊接的填充料back weld 封底焊缝，封底焊背面焊缝，背面焊welding torch 焊接喷灯，焊接吹管，焊炬，气焊嘴welded chert 熔合燧石；玉髓燧石,红色豆粒燧石horizontal welding 横焊，水平焊，水平焊接，横向焊接butt weld 对焊,对接焊缝；对接焊,对头焊缝Sigma welding 惰性气体保护金属极弧焊, 西格马焊接welding regulator 焊接气体减压器，焊接电流调节器spot weld 点焊缝，点焊接(电阻焊的一种) welding converter 焊接变流机；焊接变流机,电焊机wandering welding 分段跳焊；分段跳焊,分散间隔焊series welding 单边多电极焊接, 串焊, 系列焊接flash welding 火花〔电弧,闪光〕焊,电弧对焊接weld porosity 焊缝气孔；焊缝气孔,焊缝孔隙bevel weld 坡口焊缝,铲边焊缝；斜角焊缝welding goggles 焊工护目镜；黑玻璃,滤色玻璃forge welded 锻焊的pipeline welding 管线焊aluminithermic weld 铝热焊接dry weld 干式焊件production weld 制品焊接hydrogen welding 氢焊接。
焊接专业常用词汇中英文对照表
汉义English DescriptionK形坡口double bevel grooveU V组合坡口combination U and V grooveX射线探伤X-Ray radiographyX形坡口double V grooveγ射线探伤gamma radiography凹坑pit凹形角焊缝concave fillet weld白点fish eye摆动焊道weave bead保护气氛炉中钎焊brazing in controlled atmosphere 保护气体shielding gas保护气体-背部保护气backing flow保护气体集合管shielding gas manifold assembly 保护气体流量（速）shielding gas flow保护气体-拖尾保护气shielding trailing保留垫板permanent backing爆炸焊explosion welding并列断续角焊缝chain intermittent fillet weld并列断续角焊缝chain intermittent fillet weld补焊repair welding不熔化电极nonconsumable electrode步进缝焊step-by-step welding槽焊slot welding侧面角焊缝fillet weld in parallel shear层间温度interpass temperature层状撕裂lamellar tearing超声波焊ultrosonic welding超声波监视器ultrasonic monitor超声波钎焊ultrosonic brazing超声波探伤ultrasonic inspection超声波探伤ultrasonic test超声波探头ultrasonic transducer车间焊接shop welding虫状气孔worm hole porosity穿透型焊接法keyhole-mode welding船形焊fillet weld in flat position串联点焊series-spot welding磁粉探伤magnetic particle inspection 磁粉探伤magnetic particle test磁偏吹magnetic blow粗滴过渡globular transfer错位mismatch,offset打底焊道backing weld; backing run 带极堆焊strip surfacing单边V-V组合坡口combination bevel V groove 单边V形坡口bevel单道焊single pass welding单面J形坡口single J groove单面U形坡口single U groove单面V形坡口single V groove单面单边V形坡口single bevel groove单面点焊indirect spot welding单面盖板接头single strapped joint单面焊single side welding单面焊welding from one side单面坡口single groove导电咀wire guide; contact tube等离子弧堆焊plasma arc surfacing低尘低毒焊条low fume and harmless electrode低氢型焊条low hydrogen type electrode; hydrogen controlled electrode 滴状过渡globular transfer底层（封底）焊条uranami welding electrode (for root sealing)地线夹，地线卡earthing clamp; ground clamp电磁平台electromagnetic platen电弧点焊arc spot welding电弧动特性dynamic characteristic of arc电弧焊arc welding电弧静特性static charactristic of arc电弧力arc force电弧偏吹arc blow电弧钎焊arc brazing电弧挺度arc stiffness电弧稳定性arc stability电弧自身调节arc self-regulation电极压力electrode pressure电容贮能点焊condenser discharge spot welding电石carbide电渣焊electro-slag welding电子束功率beam power电阻对焊upset butt welding电阻钎焊resistance brazing顶锻upset顶锻电流upset current顶锻力upset force顶锻时间upset time定位板strong-back (to control the relative position of the weldment)定位焊缝tack weld端接焊缝edge weld短路过渡short circuiting transfer短路过渡short circuiting transfer断续焊缝intermittent weld断续角焊缝intermittent fillet weld锻压时间forge time堆焊surfacing;building up welding钝边root face钝边厚度thickness (width) of root face多层焊multi-layer welding多道焊multi-pass welding多点焊multiple-spot welding多点凸焊multiple projection welding多丝埋弧焊multiple-wire submerged arc welding惰性气体保护焊inert-gas arc welding二氧化碳气体保护焊carbon-dioxide arc welding返修焊rewelding防护白玻璃cover glass飞边upset metal; fin飞溅spatter飞溅率spatter loss coefficient非承载焊缝connective weld非转移弧nontransferred arc分段多层焊block sequence welding (several stages by multi layers) 分段退焊backstep sequence风动砂轮pneumatic grinder封底焊道back weld; sealing run干粉显示剂(渗透探伤用）dry developer感应钎焊induction brazing钢丝刷wire brush高频电阻焊H.F. Resistance welding高频引弧high frequency arc striking根部半径root radius根部焊道root pass根部间隙root gap工地焊接field welding工作压力表working-pressure gage挂渣adhering slag; slag (slag after cutting)管状焊丝（药芯焊丝）flux-cored electrode wire管状焊丝气体保护焊gas-shielded flux-cored welding滚点焊roller-spot welding过热区overheated zone氦弧焊helium arc welding焊波ripple焊材welding materials (including electrode, wire, flux, shielding gas etc.) 焊层weld layer焊穿burn through焊道下裂纹under bead crack焊道中心纵向裂纹centerline crack焊点welding spot焊缝（道）weld; bead焊缝凹度concavity焊缝背面back of weld焊缝长度weld length焊缝成形appearance of weld焊缝成形系数form factor(of the weld)焊缝代号welding symbols焊缝厚度weld actual throat; actual throat thickness 焊缝计算厚度theoretical throat焊缝金属weld metal焊缝宽度weld width焊缝类型-点焊缝spot weld焊缝类型-对接焊缝butt weld焊缝类型-缝焊焊缝seam weld焊缝类型-角焊缝fillet weld焊缝类型-喇叭口焊缝flare weld焊缝类型-椭长焊缝slot weld焊缝凸度convexity焊缝余高weld reinforcement焊缝正面face of weld焊缝轴线axis of weld焊割两用炬combined cutting and welding torch焊根root of weld焊根裂纹root crack焊工welder(or)焊工升降台welder's lifting platform焊工手套welding glove焊后热处理post welding heat treatment(PWHT)焊机welder; welding machine焊剂flux焊剂保护层shield produced by flux焊剂垫flux backing焊件weldment焊脚weld leg焊脚leg of fillet weld焊脚尺寸fillet weld size焊接welding焊接保护气气瓶welding shielding gas cylinder焊接变位机positioner焊接变形welding deformation焊接残余变形welding residual deformation焊接残余应力welding residual stress焊接操作机manipulator焊接衬垫welding backing焊接电极welding electrode焊接电缆welding cable焊接电流welding current焊接电压welding voltage焊接电源welding power supply焊接发尘量total amount of weld fumes焊接翻转机welding tilter焊接方法welding method焊接方法-等离子焊plasma arc welding焊接方法-点焊spot welding焊接方法-电子束焊electron beam welding焊接方法-电阻焊resistance welding焊接方法-激光焊接laser beam welding焊接方法-埋弧焊submerged arc welding焊接方法-气体火焰焊gas flame welding焊接方法-钎焊brazing; soldering焊接方法-闪光对焊flash but welding焊接方法-手弧焊shielded metal arc welding(SMAW) 焊接方法-钨极氩弧焊argon-arc welding焊接方法-药芯焊丝焊接flux-cored welding焊接飞溅welding spatter焊接工艺welding process(procedure, workmanship) 焊接工艺评定welding process qualification焊接工作台welding bench焊接滚轮架turning rolls焊接回路welding circuit焊接机器人welding robot焊接机头welding head焊接夹(胎）具welding fixture (jig)焊接检验welding examination焊接裂纹weld crack焊接清理用刨锤chipping hammer焊接缺陷weld defect焊接缺陷weld defect焊接热循环weld thermal cycle焊接顺序welding sequence焊接速度welding rate焊接通电时间weld time焊接温度场welding temperature field焊接性（可焊性）weldability焊接性试验weldability test焊接循环welding cycle焊接烟尘weld fumes焊接应力welding stress焊接有害气体weld toxic gases焊炬welding torch焊瘤overlap; weld lap焊帽welder shielding helmet焊前预热preheat焊钳electrode holder焊枪welding gun焊丝wire焊丝间距distance between (two or above) wire焊丝盘electrode-wire reel焊态as welded焊条（棒）(covered) electrode焊条保温筒electrode dryer; quiver焊条工艺性usability of electrode焊条烘箱electrode baking oven; electrode dryer焊条夹持端electrode bare terminal焊条压涂机welding rod extrusion press焊条引弧端electrode striking end焊条直径electrode diameter焊芯（welding electrode ) core wire焊渣覆盖层slag blanket焊趾weld toe焊趾裂纹weld toe crack合金过渡系数transfer efficiency；recovery(of an element) 合金剂alloying constituent黑玻璃filter glass横角焊fillet weld in horizontal position横向焊缝transverse weld横向裂纹transverse crack弧长length of arc弧焊变压器arc welding transformer弧焊发电机arc welding generator弧焊整流器arc welding rectifier弧坑裂纹crater crack弧柱arc column弧柱压降voltage drop in the arc column护脚spats环缝焊接circular seamwelding环形焊缝girth weld; circumferential weld回火（烧）flash-back回火保险器flashback arrester回火防止器flashback arrestor混合气体保护焊mixed gas arc welding火焰钎焊flame brazing; torch brazing极性polarity加强板stiffener加强板strongback加速电压acceleration voltage夹钳tongs夹钨tungsten inclusion夹杂inclusion夹渣slag inclusion减压器pressure regulator碱度basicity; alkaline碱性焊条basic electrode; alkali coating electrode 碱性渣basic slag; alkali slag交错断续角焊缝staggered intermittent fillet weld交错断续角焊缝staggered intermittent fillet weld胶接点焊spotweld-bonding角焊缝断面形状profile of fillet weld接头型式joint type接头型式-T型接头T joint接头型式-搭接lap joint接头型式-端接接头edge joint接头型式-对接butt joint接头型式-翻（卷）边接头flanged joint接头型式-角接corner joint接头型式-十字接头cross joint接头型式-锁底对接接头lock butt joint接头型式-套管接头muff joint；sleeve joint接头型式-斜对接接头scarf butt joint金属极（熔化极）惰性气体保护焊gas metal arc welding (MIG)金属芯焊丝metal cored wire金属浴钎焊molten metal bath dip brazing浸沾钎焊dip brazing拘束度restraint intensity卷边端接corner flange开坡口beveling扩散焊diffusion welding; diffusion bonding 扩散氢diffusible hydrogen喇叭V形坡口flare V groove喇叭单边V形坡口single flare bevel烙铁solder iron烙铁钎焊iron soldering冷裂纹cold crack冷裂纹cold crack立角焊fillet weld in vertical position立向下焊条electrode for vertical down welding 连续点焊stitch welding连续焊缝continuous weld连续角焊缝continuous fillet weld链状夹杂line inclusion裂纹敏感性crack sensitivity裂纹试验cracking test临时垫板temporary backing炉中钎焊furnace brazing螺旋型焊缝spiral weld; helical weld螺柱焊stud welding脉冲等离子弧焊pulsed plasma arc welding脉冲点焊pulsed spot welding脉冲电弧pulsed arc脉冲喷射过渡pulsed spray transfer脉冲氩弧焊pulsed argon arc welding毛刺fin; flash密封焊缝seal weld密封性检验leak test母材base metal; parent metal耐压检验pressure test逆火backfire耦合剂（超声波探伤用）acoustic couplant喷溅splash (during spot welding, projection welding etc.) 喷咀nozzle喷射过渡spray transfer喷射过渡spray transfer疲劳裂纹fatigue crack偏心度eccentricity坡口表面groove surface坡口夹角groove angle( angle of Vee)坡口间隙groove angle坡口角度root gap; root openning坡口宽度groove width坡口深度groove depth坡口斜角bevel angle (angle of preparation)坡口型式groove type破坏检验destructive test铺展性spreadability气电立焊electro-gas welding; enclosed welding 气焊眼镜welding goggles(esp. in gas welding) 气孔blowhole；porosity气密试验pneumatic testing气密性检验air tight test气体保护电弧焊gas shielded arc welding气体减压器gas pressure regulator气体净化器gas purifier钎缝brazed seam钎缝金属brazed metal钎焊brazing; soldering钎焊间隙joint clearance of brazing钎焊接头brazed joint钎焊面faying face钎焊时间holding time钎焊温度brazing temperature钎焊性brazability; solderability钎剂brazing flux钎剂夹杂flux inclusion (in brazing or soldering) 钎炬brazing torch钎料brazing alloy; brazing filler metal钎着率ratio of brazing area氢致裂纹hydrogen induced crack倾斜焊Inclined position welding倾斜仰焊overhead position welding with weld inclined清根back chipping; gouging清渣slag remove热处理heat treatment热剂焊thermit welding热裂纹hot crack热影响区heat affected zone(HAZ)溶蚀erosion (the base metal was over-melted by the molten flux) 熔滴globule熔滴droplet熔滴过渡material transfer；metal transfer熔滴过渡形式modes of metal transfer熔滴接通熔池drop touches weld puddle熔敷金属deposition; deposited metal熔敷速度deposition rate熔敷系数deposition coefficient熔敷效率deposition efficiency熔焊fusion welding熔合比penetration ratio熔合线bond line; weld junction熔合线melt run (line of fusion)熔化电极consumable electrode熔化极惰性气体保护焊MIG welding熔化极脉冲氩弧焊pulsed metal argon arc welding熔化速度melting rate; burn-off rate熔化系数melting coefficient熔剂料斗flux hopper熔宽不足insufficient width熔宽过大excessive width熔炼焊剂fused flux熔深penetration; depth of fusion熔透焊道penetration bead熔透型焊法fusion type welding熔渣slag熔渣流动性fluidity of the slag软电弧soft arc软钎焊soldering (I.e with lead,tin etc.)软钎料solder (the melting point of which is below 450cent.) 润湿性wettability塞焊plug welding塞焊缝plug weld闪光对焊flash butt welding闪光时间flash time上坡焊upward welding in the inclined position上坡焊upward welding in inclined position烧穿melt-thru; burn-through烧结焊剂sintered flux; agglomerated flux射线探伤radiographic inspection; radioscopy深熔焊deep penetration welding渗透探伤penetrant inspection湿粉显示剂（渗透探伤用）wet developer实心焊丝solid wire electrode试件test piece; specimen试样test speciment; coupon手压点焊push welding束流beam current双面J形坡口double J groove双面U形坡口double groove双面盖板接头double strapped joint双面焊double side welding双面焊welding from both side水玻璃water glass(material); sodium silicate; soluble glass 水下焊under water welding水压试验hydraulic testing送丝机构wire feeder送丝速度wire feed rate酸度acidity酸性焊条acid electrode酸性渣acid slag损失系数loss efficiency塌陷excessive penetration钛钙型焊条calcium-titania coating electrode钛铁矿型焊条ilmenite type electrode钛型焊条titania coating electrode碳当量carbon equivalent碳弧焊carbon arc welding填充金属filler metal挑弧焊whipping welding (the arc apart the pool regularly 跳焊skip sequence铁粉焊条ferric (iron) powder type electrode铜滑块copper shore凸焊projection welding凸形角焊缝convex fillet weld涂料coating mixture; coating material脱氧剂dioxidizer脱渣性detachability外观检查visual examination微束等离子弧焊micro-plasma arc welding未焊满incompletely filled groove未焊透incomplete penetration; lack of penetration未钎透incomplete penetration (in brazing or soldering) 未熔合incomplete fusion; lack of fusion稳弧剂arc stabilizer涡流探伤eddy current test钨极惰性气体保护焊TIG welding钨极脉冲氩弧焊pulsed tungsten argon arc welding无损检验non-destructive testing稀释dilution稀释率dilution rate下脚料箱scrap iron box下坡焊downward welding in the inclined position纤维素型焊条cellulose type electrode线能量energy input; heat input线状焊道string bead向上立焊vertical up welding向下立焊vertical down welding小角缝焊接light fillet weld小孔效应keyhole effect斜交T形接头inclined tee joint斜交角焊缝oblique fillet weld旋转电弧rotating arc旋转电弧焊rotating arc welding压焊pressure welding压缩喷嘴constricting nozzle延迟裂纹delay crack延迟裂纹delayed crack盐浴钎焊salt bath brazing阳极斑点anode spot阳极区anode region阳极压降anode drop仰角焊fillet weld in overhead position氧化铁型焊条ferric oxide electrode氧气瓶oxygen cylinder氧炔焊炬oxyacetylene welding torch咬边undercut药皮coating药皮重量系数gravity coefficient of coating乙炔acetylene乙炔发生器acetylene generator乙炔瓶acetylene cylinder易熔塞fusible plug易碎安全塞frangible safety plug阴极斑点cathode spot阴极区cathode region阴极压降cathode drop引出板run-off tab; end tab引弧arc striking引弧板run-on tab; end tab引弧电压striking voltage荧光渗透试验fluorescent penetrant inspection硬电弧forceful arc硬钎焊brazing (I.e with copper, braze etc.)硬钎料brazing filler metal (the melting point of which is above 450cent.) 右焊法backhand welding( from the left end to the right)余高不足insufficient reinforcement余高过大excessive reinforcement预热时间preheat time预压时间squeeze time原子氢焊atomic-hydrogen arc welding再热裂纹reheat crack造气剂volatile constituent造渣剂slagforming constituent增感屏（射线探伤中）intensifying screen渣池slag bath渣壳solidified slag窄间隙焊narrow gap welding粘结焊剂bonded flux粘结剂binder真空钎焊vaccum brazing正面角焊缝fillet weld in normal shear直边坡口square groove至电源to power supply至焊丝送进装置to electrode wire supply重力焊gravity welding重力焊条gravity electrode (longer than common type electrode) 转移弧transferred arc着色渗透试验dye penetrant inspection自保护电弧焊self-shielded arc welding自钎剂钎料self-fluxing brazing alloy纵向焊缝longitudinal weld阻尼探头damped transducer左焊法forehand welding（from the right end to the left)。
焊接常用英汉对照
actual weld-throat thick-ness 焊缝厚度all-around weld 整周焊缝all-around weld （整周焊缝）环焊缝angle butt weld 斜对接焊angle weld 角焊appearance of weld 焊缝成形arc-seam weld 电弧缝焊arc-spot weld 电弧点焊arc-weld 电弧焊aspect ratio of weld 焊缝成形系数at weld edge 在焊缝边上attachment weld 连接焊缝automatic spot weld 自动点焊法automatic weld 自动焊接axis of a weld 焊缝中心线; 焊接轴线axis of weld 焊缝轴线; 焊接轴线back of weld 焊缝背面backing groove of weld 焊缝反面坡口backing weld 底焊; 底焊焊缝bare metal arc weld 裸焊条电弧焊bead weld 珠焊; 堆焊bead-on-plate weld 堆焊焊缝beading weld 凸焊beam-to-beam weld 梁间焊接; 梁式引线焊接block sequence weld 分段多层焊bond weld 钢轨接头焊接bridge seam weld 桥缝焊接; 桥线焊brize weld 硬焊butt weld 对接焊缝butt weld ends 对头焊接端butt-weld 碰焊; 平式焊接; 对头焊接butt-weld in the downhand position 对butt-weld joint 对头焊接butt-weld pipe mill 对焊管轧机button spot weld 按电钮点焊cap weld 最后焊层; 盖面焊缝carbon content of weld materials 焊接材料的碳含量cast-weld construction 铸焊结构caulk weld 填缝焊caulking weld 密实焊缝chain intermittent fillet weld 链式分段角焊; 并列间断角焊缝chain intermittent weld 并列焊接circular weld 环形焊缝circumferential weld 环缝; 环焊缝cleft weld 裂口焊closed weld 底边无缝焊; 无间隙焊缝closed-chamber fusion weld 闭室熔焊cluster weld 丛聚焊缝coil weld 卷板对接焊; 卷板对接焊; 板卷焊cold weld 冷压接commutator- controlled weld 换向控制焊接complete penetration butt weld贯穿对焊composite weld 紧密焊缝; 强度密封焊缝concave filled weld 凹形角焊缝concave filler weld 凹角焊concave fillet weld 凹面填角焊concaveweld 凹焊缝; 凹面焊; 凹形焊缝; 轻型焊connective weld 联系焊缝continuous butt-weld mill 连续式炉焊管机组continuous fillet weld 连续（填）角焊缝; 连续角焊缝; 连续贴角焊continuous weld 连续焊缝continuous weld process 连续式炉焊管法contour weld 特形焊接convex fillet weld 凸角焊缝; 凸形角焊缝convex weld 凸焊缝; 凸形焊缝copper weld wire 包铜钢丝corner flange weld 单卷边角焊缝corner weld 角焊corner-flange weld 卷边角焊缝; 卷边角焊缝crack of weld 焊部裂纹cross weld 十字交叉焊缝; 横向焊缝cross-wire weld 十字焊crotch weld 楔接锻接; 楔接焊接cup weld 带盖板焊缝depth of weld 焊接深度dissimilar weld metal 不同的焊接金属; 不同金属的焊接distance between the toes of a weld 焊缝宽度double groove weld 双面坡口焊缝double-bevel groove weld 双斜边坡口焊缝; 双斜坡口焊double-flanged butt weld 双弯边对接焊缝double-V groove weld 双斜边坡口焊缝; 双斜坡口焊downhand weld 平焊缝duplex spot weld 双点点焊接头edge joint weld 边缘焊edge weld 端接焊; 端接焊缝; 端面焊缝; 对边焊electric resistance weld mill 电阻焊管机electric weld-pipe mill 电焊管机electric-weld pipe mill 电焊管机emporary weld 临时点定焊缝excess weld metal 焊缝补强金属; 补强; 补强焊料; 补强金属excess weld metal（焊缝的）余高explosive weld 爆炸焊接face of weld 焊缝表面; 焊接面fibrous weld 纤维状焊缝field weld 现场焊接filler weld 填角焊缝fillet weld 角焊缝; 填角焊; 贴角焊fillet weld in normal shear （搭接接头的）正面角焊缝fillet weld in parallel shear 侧面角焊缝; 侧面填角焊fillet weld in the flat position 角接平焊; 水平角焊缝fillet weld in the horizontal position 横向角焊缝fillet weld size 焊角尺寸; 填角焊缝尺寸flame weld 火焰焊接flange weld 卷边焊缝; 卷边焊缝flange-to-web weld 卷边焊缝; 卷边焊缝flanged butt weld 弯边对接焊flanged edge weld 卷边焊; 卷边焊flash butt weld 闪光焊flash weld 闪速对焊flat faced fillet weld 平顶角焊缝焊接flat fillet weld 平角焊ing of fillet weld 角焊缝平焊; 船形角焊flush fillet weld 平角焊flush weld 削平补强的焊缝; 平焊接; 无加强高的焊缝forge weld 锻焊焊缝forged weld （焊后锻压的）锻压焊缝form factor of the weld 焊缝成形系数formation of weld 焊缝成形front fillet weld 正侧面填角焊缝; 正面填角焊front（al） fillet weld 正面角焊缝full fillet weld 满角焊缝; 全角焊full penetration butt weld 满对接焊full weld 满焊full-fillet weld 满角焊full-sized weld 全尺寸焊缝fullstrength weld（与母材等强）等强焊缝gap weld 特殊点焊; 双极单点焊gas-pressure weld 气压焊girth weld 环形焊缝gravity weld 倚焊groove weld 坡口焊; 坡口焊缝; 有坡口焊缝; 凹槽焊groove-weld joint 有坡口焊接接头hammer weld 锻焊hand weld 手焊焊缝height of reinforcement of weld 加强焊缝高度helical-weld pipe 螺旋焊管high performance weld flux 高性能焊剂horizontal fillet weld 横向角缝焊接horizontal weld 横向焊缝horizontal-vertical fillet weld 横向垂直角焊缝hot weld encapsulation 热焊封袋hydraulic automatic weld 液压自动焊接hydraulic weld process 液压焊接法inclined weld 斜焊inconel weld 单面焊缝incorrect weld profile 焊缝形状不对incorrect weld size 焊缝尺寸不对induction weld mill 感应焊管机inside corner weld 内角焊接inside fillet weld 内角焊接inside weld 内焊缝insufficient or excess reinforcement of weld 加强焊缝不足或过量intermittent fillet weld 间断角缝焊接断续角焊缝intermittent weld 断续焊; 断续焊缝jam weld 对接焊; 对头焊接lap fillet weld 搭接角焊缝laser （beam） weld （ing）激光焊lateral weld 侧焊; 侧面焊缝leg of a fillet weld 角焊缝; 角焊缝焊脚leg of fillet weld 圆角焊肉厚length of weld 焊缝长度light closing weld 轻连续焊接light fillet weld 轻型填角焊; 小填角焊light weld 轻焊缝Lincolnweld埋弧自动焊longitudinal fillet weld 纵向角焊longitudinal weld 纵向焊缝longitudinal weld ( 焊接用语) 纵缝loose weld 脱焊main weld 主焊缝mash seam weld 压薄缝焊; 滚压焊mash weld 点焊; 点压焊melt thru weld 熔透焊缝melt-through weld 透溶焊melten weld pool 焊接熔池melting through weld 熔透焊缝miter weld 平顶角焊缝; 斜接角焊缝molten weld metal 熔融焊接金属mulitple impulse weld 多脉冲焊缝multilayer weld 多层焊缝multipass weld 多道焊缝multiple arc weld 多弧焊缝multiple-electrode submerged arc weld 多电极埋弧焊multiple-pass weld 多道焊缝; 多路焊接multirun weld 多道焊缝nonpressure thermit weld 不加压热剂焊缝normal weld 正常焊接oblique fillet weld 斜交角焊缝; 斜角焊接one-pass weld 单层焊缝open butt weld 开口对接焊open weld 留间隙焊缝; 空隙焊outside weld 外焊缝over weld 过焊overhead fillet weld 仰焊角焊缝overhead weld 仰焊oversize weld 超尺寸焊缝oxygen weld 氧气焊接parallel-arc weld 并列弧焊patch weld 补焊; 补孔焊缝Peltier's cross weld 珀耳帖交叉焊接penetration weld 熔透焊缝percussion weld 冲击焊缝; 冲击焊接periphera weld 环形焊缝pitch of weld 焊缝接距; 焊线距plain butt weld 无坡口对接焊; 平头对接焊缝plasma-arc weld 等离子弧焊接plug weld 塞焊焊缝point of weld 焊接点point weld 点焊poor weld 劣质焊缝; 有缺陷的焊缝porous weld 多孔焊缝; 疏松焊缝positioned weld 平位焊缝; 暂焊post weld ann ealed (PWA)焊后退火poured weld 铸焊焊缝powder weld process 粉末焊接法practice weld 试验焊缝pppppppppppp 压焊pressure-controlled weld 压力控制焊接pressure- tight weld 气密焊; 密封焊道principal weld 主要焊缝profile of fillet weld 填角焊缝轮廓progress of weld 焊向projection weld 凸焊; 凸焊焊缝projection weld machine 凸点电阻焊机pulsating weld 脉冲接触焊push weld 挤焊qqqqqqqqqqqq 钉焊reinforced butt weld 补强的对接焊缝; 补强式对接焊缝reinforced weld 加强焊接reinforcement of weld 焊缝加厚; 补强金属; 加强焊缝resistance weld mill 电阻焊管机resistance weld pipe 电阻焊管resonance butt weld 谐振式对接焊restarting a weld 再引弧ripple weld 鳞状焊缝rivet weld 电铆; 电铆焊缝root face of weld 焊缝根部钝边root gap of weld 焊缝根部间隙root of weld 焊缝根部; 焊根root opening of weld 焊缝根部间隙root radius of weld 焊缝坡口根部半径sagged weld 下垂焊缝scarf weld 楔口焊接seal weld 填焊; 致密焊缝; 密封焊; 密封焊道; 密封焊缝sealing weld 封焊seam weld 滚焊semi-automatic arc weld 半自动电弧焊sequence weld timer 序列焊接时间调节器shallow weld 浅焊shop weld 工厂焊接shot weld 点焊shoulder of weld 焊缝根部钝边side fillet weld 侧面角焊缝; 侧面填角焊缝; 侧面贴角焊side lap weld 侧边搭接焊; 弯边搭焊缝side weld 侧焊缝; 边焊single lap weld 单搭接焊single strap butt weld 单面盖板对接焊single-bevel groove weld 单斜角槽焊single-fillet weld 单边角接焊缝single-pass weld 单道焊site weld 现场焊接; 安装焊; 安装焊接size of a fillet weld 焊角尺寸size of weld 焊件的大小; 焊区尺寸skew weld 斜焊skin weld 表面焊接sleeve weld 套筒焊接slip-weld hanger 卡瓦焊接套管挂slot weld 槽塞焊; 长孔焊; 开槽搭焊缝切口焊缝ing slotted weld 槽焊slotted lap weld 切口搭接焊smooth fillet weld 平填角焊缝socket weld ends 承插焊接端soft-weld 铜镍焊条合金solvent weld 溶剂焊接space of intermittent weld 断续焊缝间距; 断续焊间距spiral weld 螺旋形焊缝spiral weld-pipe mill 螺旋焊管机spot weld 焊点spot weld bonding 胶结点焊spot weld nugget 点焊熔核spreading weld 宽缝焊接; 加宽的焊缝square butt weld 平头对接焊缝square groove weld 无坡口槽焊staggered intermittent fillet weld (ing) 交错断续角焊staggered intermittent weld 交错断续焊缝; 交错间断焊staggered plug weld 交错塞焊standard reinforced fillet weld 标准加强角焊缝stick-out weld 未熔合点焊接头stitch-and-seam weld 点线焊straight butt weld 无坡口对接接头strapped weld 搭板对接焊缝strength weld 受载焊缝; 强固焊接; 承载焊缝; 高强度焊接structural weld 强固焊缝surface of weld 焊缝表面surface weld 表面焊缝surface weld metal buildup 表面焊缝金属的形成synthetic apparatus for weld thermal cycle 焊接热循环模拟装置T weld 丁字接头焊缝T-filled weld 丁字形角焊T-fillet weld 丁字接头角焊缝tack weld 定位焊点; 定位焊缝; 临时点焊; 预焊; 平头焊接(welding) 定位焊tandem arc weld 前后弧焊temporary weld 临时点固焊缝tension weld 受拉焊缝test weld 试焊throat depth (thickness) of fillet weld 角焊缝厚度throat of fillet weld 凹角焊喉; 填角焊缝喉长throat of weld 凹角焊喉tight weld 密封焊接; 致密焊缝tight-strong weld 密实强固焊缝toe of the weld 焊缝边界toe of weld 焊趾toe weld 趾部焊缝torch weld 气焊焊缝total amount of weld fumes 焊接发尘量transverse fillet weld 横向角焊缝; 正面角焊transverse weld 横向焊缝trial weld 试验焊接undercut weld 底切焊接undressed weld (增加焊缝) 未加工焊缝unequal fillet weld 焊脚不等的角焊缝unfitness of butt weld 焊缝对口错边量union-melt weld 埋弧焊unload weld 非承载焊缝unspaced butted weld 无间隙对接焊缝upgrading of boiler weld 锅炉焊缝加强vertical fillet weld 立焊角焊缝vertical weld 立焊weak weld 不强固焊缝weaving weld 横向摆动焊缝weld 焊; 焊接的; 补焊weld all around 围焊weld appearance 焊缝外观weld assembly 焊接组件weld back-up 焊缝背垫weld backing 焊缝衬垫weld bead 焊缝; 熔敷焊道weld bead height 焊缝高度weld beading 焊瘤weld bond 熔合线weld bridge seam搭桥焊缝；桥接焊缝weld cap 焊帽weld center line 焊缝中心线weldcollar 加强焊缝焊瘤weld crack 焊接裂纹weld crater 熔池weld crosswise 交叉焊接weld decay 焊缝腐蚀；焊接接头晶间腐蚀；焊接侵蚀; 焊接区晶间腐蚀weld decay （焊接后）敏化区腐蚀weld defect 焊接缺陷weld delay time 焊接延迟时间weld deposit 堆焊weld deposits cleaning 焊接熔敷金属清理weld edge 焊缝边缘; 焊缝表面边缘weld edgewise 沿边焊接weld flange connection 焊接法兰连接weld flash 焊瘤weld flaw 焊接缺陷weld flush 焊缝隆起weld fumes 焊接烟尘weld gage 焊缝检查规; 焊缝卡规weld gauge 焊缝量规weld heat input 焊接热输入; 焊接线能量weld holder 焊接夹持架; 焊接架weld inspection 焊缝质量检验; 焊接检查weld interface 焊缝界面; 焊接界面weld interval 焊接时间weld is accepted 焊缝合格weld jig 焊接夹具weld joint 焊缝weld junction 熔焊线; 熔合线weld layer 焊接层weld length 焊缝长度weld line 焊缝线; 焊缝轴线; 焊接线; 焊线weld machined flush 削平补强的焊缝weld mark 焊缝符号; 焊缝记号; 焊接痕; 熔缝weld mesh crate 焊接网格weld metal 焊缝金属; 焊接金属weld metal buildup surface 金属堆焊表面weld metal composition 焊接金属组成weld metal cracking 焊缝裂纹weld metal zone 焊缝金属区; 焊接金属熔化区weld nugget 焊点熔核weld on bottom 底焊weld overlap 重叠区weld pass 焊接通道weld penetration 焊缝熔深; 焊透深度weld period 焊接时间weld pitch 焊缝距weld porosity 焊缝气孔weld preheating 焊前预热weld preparation 焊缝坡口加工weld puddle 熔池weld reinforcement 焊缝补强; 焊缝加强; 焊接补强weld repairs 焊接修补weld ripple 焊缝波纹weld root 焊件剖口; 焊接根weld root opening gap 焊缝根部间隙weld root reinforcement 焊缝反面加强weld rotation 焊缝转角weld seam pipe 焊缝管weld shape 焊缝形状weld shielding 焊接区保护; 焊接熔池保护weld slope 焊缝倾角weld spacing 焊点距; 焊缝间距weld strain 焊接应变weld strength 焊接强度weld surface 焊缝表面weld swell 焊缝隆起weld thermal cycle 焊接热循环weld thickness 焊缝厚度weld time 焊接时间; 焊接通电时间; 接触焊通电时间weld toxic gases 焊接有害气体weld trimmer 焊缝清理机weld up 焊补weld wheel conditioner 焊轮调节器weld width 焊缝宽度weld wire 包铜钢丝weld zone 焊缝区; 焊接区weld-form factor 焊缝形状系数weld-fusion line 焊缝熔合线weld-in nozzle 焊入式喷嘴weldinterval timer 焊接间隔记时器weld- shrunk cylinder 包扎式圆筒weld- shrunk multilayered cylinder 包扎式多层圆筒; 多层包扎式圆筒weldthroat thickness depth 焊缝厚度window type restraint weld cracking test 窗口拘束焊缝抗裂试验; 窗形拘束抗裂试验zigzag intermittent fillet weld 锯齿形断续角焊缝; 锯齿形断续角焊缝zone of weld 焊缝表面AC & D. C. arc welding machine 交直流弧焊机AC arc welding 交流电弧焊AC gas metal-arc welding process 交流熔化极气保护焊AC gas tungsten arc welding 交流钨极气保护焊AC welding set 交流焊机; 交流焊接变压器AC-dc welding machine 交直流两用焊机acetylene welding 气焊; 乙炔焊; 乙炔焊接acetylene welding torch 乙炔焊炬; 乙炔接焊吹管air-acetylene welding 空气- 乙炔焊接all-position welding 全位置焊接alloy steel gas welding rod 合金钢气焊条alternating current arc welding 交流电弧焊alternating current welding machine 交流电焊机aluminium alloy arc welding electrode 铝合金焊条aluminothermic welding 铝热焊; 铸焊angle backwards welding 后倾焊angle butt welding 斜口对接焊angle forwards welding 前倾焊annealing welding wave 退火焊波antogenous welding 氧炔焊apparatus for butt welding 平接压焊夹具arc braze welding 电弧钎焊arc flash welding 电弧闪光焊arc spot welding 电铆焊arc stud welding 柱钉电弧焊; 螺柱电弧焊arc voltage feedback controlling arc welding 弧压反馈电弧焊arc welding 电弧焊; 电弧焊接; 弧焊arc welding electrode 电弧焊条arc welding generator 电弧焊接用发电机; 弧焊发电机arc welding generator with independent excitation 自激弧焊发电机他激电焊发电机arc welding generator with selfexcitation 自激电焊发电机arc welding machine 弧焊机; 电焊机; 电弧焊机arc weldi ng mask电弧焊遮罩arc welding process 电弧焊接工艺过程arc welding rectifier 弧焊整流器arc welding robot 弧焊机器人弧焊变压器电弧焊用焊条电焊厂电弧氧乙炔焊arc welding 氩弧焊接welding 钨极氩弧焊氩弧焊自动氩弧焊氢原子焊welding 原子氢焊welding 原子氢焊接不锈钢焊接autogenous pressure welding 自动压合热焊autogenous welding 气焊automatic arcwelding head 自动电弧焊接机头automatic arcwelding machine 自动电焊机; 自动弧焊机automatic drying line forwelding electrode 电焊条自动烘焙线automatic slag poolwelding 自动电渣焊automatic spot welding 自动点焊automatic submerged arc welding 自动埋弧焊automatic submerged slag welding of rail 钢轨automatic submerged-arc welding machine 埋弧自动焊机automatic transverse welding 横向自动焊automatic welding 自动焊; 自动焊接automatic welding head 自动焊头automatic welding machine 自动焊接机automatic welding of circumferential seams环缝自动焊automatic welding process 自动焊接工艺规程automation of welding 焊接自动化back handwelding 后退焊; 反手焊接back step welding 反手焊接back ward welding 反手焊接back welding 底焊; 退焊法back-step welding 分段退焊法backhand welding 逆向焊; 右焊法; 后焊法; 向后焊backing welding 打底焊backstep welding 分段逆焊; 分段退焊; 反向焊; 逐步退焊法; 逆向焊backstep welding sequence 分段退焊次序backward welding 后倾焊; 后退焊; 向右焊balanced welding 对称焊bare welding rod 光焊条bare wire arc welding 光焊丝电弧焊bead welding 窄焊道焊接bench arc welding machine 台式弧焊机bevel welding 斜角焊blacksmith welding 锻工焊接; 锻焊block sequence welding 分段多层焊; 分段连续焊接block welding 块焊接block welding sequence 分段多层焊body welding machine 罐身焊接机both sides welding 双面焊接brass welding rod 黄铜焊条braze welding 钎焊; 钎焊接; 钎接; 铜焊braze-welding 钎接焊bridge spot welding 带接合板点焊; 单面衬垫点焊; 单面搭板点焊bridge welding 桥接焊; 盖板焊arc welding arcwelding arc-welding arc-welding arcogenweldingset 电弧焊机组transformerelectrode plantargon (shielded)argon tungsten-arcargon-arc weldingargonaut weldingatomic H weldingatomic hydrogenatomic-hydrogenaustenite weldingbrize welding 硬焊build (built) up welding 堆焊build-up welding 堆焊building-up by welding 堆焊butt resistance welding 电阻对焊; 对接电阻焊butt seamwelding 对接滚焊butt seamwelding machine 对接缝焊机butt welding 对接焊; 平对焊butt welding machine 对接焊机butt welding process 对接焊法butt-welding 对接焊butt-welding machine 对焊机capability of welding vertically upwards 直上焊接能力capacitor-discharge welding 电容放电焊接carbon arc welding 碳弧焊; 碳极弧焊carbon in materials for welding 焊接用材料中的碳carbon-dioxide arc welding 二氧化碳保护焊carriage of automatic welding machine 自动焊机走架cascadewelding 阶梯式焊; 山形多层焊cascadewelding sequence 串级叠置法cast welding 铸焊cement-welding 金属陶瓷焊接centralized installation of welding machine 多站焊接chain intermittent fillet welding 并列断续角焊缝; 链式断续角焊chemical welding 化学焊circular seam welding 环缝对接焊circular seam-welding machine 环形滚焊机cleaning before welding 焊接前的清理cleaning of welding deposits 焊接沉积的清理closed butt gas pressure welding 闭式加压气焊cold welding 冷焊; 冷压焊cold-pressure welding 冷压焊combined cutting and welding torch 焊割两用炬combined cutting and-welding blow-pipe 焊割两用炬combined thermit welding 加压铸焊complete penetraction and fusion in welding 全焊透condenser (discharge) spot-welding machine 电容器放电点焊机condenser discharge spot welding 电容储能点焊; 电容贮能点焊constant current welding machine 恒流电焊机constant energy welding machine 恒功率电焊机constant voltage welding machine 恒压电焊机constant-current arc welding power source 垂降特性弧焊电源constant-current welding source 恒流式焊接电源constant-power welding source 恒功率式焊接电源constant-pressure pressure welding 恒压压力焊constant-temperature pressure welding 恒温压力焊constant-voltage welding machine 恒电压焊机constant-voltage welding source 恒压式焊接电源; 平特性焊接电源consumable electrode welding 熔化极电弧焊consumable guide electroslag welding 自耗定向电渣焊contact welding 接触焊continuous feed welding 连续送丝电弧焊continuous welding 连续焊; 连续焊接contour welding 绕焊controlled arc welding 可控电弧焊接controlled atmosohere arc welding 充气室电弧焊con trolled atmospere arc weldi ng 充气式电弧焊con trolled tun gste n-arc weld ing 自动控制弧长的钨极电弧焊controlled-transfer welding 可控过渡电弧焊convex fillet welding 凸面角焊缝copper arc welding electrode 铜焊条copperwelding rod 铜焊条copper-alloy arc weldi ng electrode 铜合金焊条copper-aluminium welding rod 铜铝焊条copper-nickel welding rod 铜镍焊条copper-silicon welding rod 铜硅焊条copper-tin welding rod 铜锡焊条copperzinc welding rod 铜锌焊条core welding-wire 焊芯core wire for welding rod 焊条芯线corrosion due to welding 焊接腐蚀cosmetic weldi ng 盖面焊cover chain welding链节式药皮包丝焊接CO 2 arc welding machine 二氧化碳弧焊机crack ing test for automatic weldi ng 自动焊抗裂试验crankshaft flashbutt welding 曲轴电阻弧花压焊cross welding 横向焊缝cyc-arc welding圆环电弧焊deck welding 重力焊deep fillet weldi ng 深角焊deep penetration welding 深熔焊deep penetration welding electrode 深熔焊条deep welding 深焊die welding模焊;冲模堆焊diesel engine driven DC arc welding machine 柴油机驱动直流弧焊机differe ntial-excited welding generator差激电焊发电机diffusion welding 扩散焊接direct spot welding 双面点焊direct welding 双面点焊direction of welding焊接方位；焊接方向disc on ti nu ous weld ing 断续焊dot welding 点焊double carb on-arc weldi ng 间接碳弧焊double side welding 双面焊接down-hand welding 俯焊downhand welding 平焊downward welding in the inclined position 下坡焊downward welding in the vertical position 向下立焊dual-arc welding 双弧焊edgeseamwelding端面接头滚焊edge welding边缘焊接edgewise welding 沿边焊接electric and pressure welding 电压力焊接electric arc spot welding 电弧点焊electric arc welding generators 电弧焊接发电机electric arc welding machine 电弧焊机electric butt welding 电阻接触焊electric resista nee weldi ng 电阻焊接; 热电阻焊electric slag welding 电渣焊electric spot welding 电点焊electric welding 电焊electric welding cast copper solder 铸铜电焊条electric welding equipment 电焊设备electric welding generator 电焊发电机electric welding hammer 电焊锤electric welding machine 电焊机electric welding plant 电焊厂electric welding pliers 电焊钳electric welding rod 电焊条electric welding strip 电焊片electric-arc welding 电弧焊electric- resista nee seam-welding 电阻缝焊electric- resista nee seam-welding machine 电阻缝焊机electrical arc welding 电弧焊接electrical resista nee weldi ng tube 电阻焊接管electrically heated welding torch 电热焊枪electro-beam welding 电子束焊接electro-gas(e nclosed) weldi ng 气电立焊electro-slag welding电磁渣焊；电渣焊electro-slag welding with plate electrode 板极电渣焊electro-welding 电焊electrode for arc welding 电焊条；电弧焊条electrode for vertical down welding 向下立焊条electrode of vertical down welding 立向下焊条electrode welding 电弧焊electrogas welding气电焊;电气焊electromagnetic percussive welding 电磁冲击焊electromagnetic stored energy welding 电磁储能焊electron beam welding 电子束焊；电子束焊接electron beam welding machine 电子束焊接机electron-beam welding 电子束焊接electronbeam welding machine 电子束焊机electron-bombardment welding 真空电子束焊electrons leaves welding 电子束焊接electropercussive welding 电冲击焊; 冲击焊; 储能焊electroslag welding 电渣焊; 电阻焊electroslag welding machine 电渣焊机electroslag welding with consumable nozzle 熔嘴电渣焊electroslag welding with wire electrode 丝极电渣焊electrostatic (percussive) welding 电能储能焊接electrostatic percussing welding 静电焊; 静电焊; 冲击焊; 储能焊electrostatic percussive welding 静电冲击焊; 静电冲击焊enclosed welding 强制成形焊接energy storage welding 贮能焊; 储能焊; 脉冲焊接erecting welding 装配焊接erection welding 安装焊接eutectic welding 低温焊exothermic welding 铝热焊expanding or welding of tube with tubesheet 管子与管板的胀接或焊接explosive welding (EW) 爆炸焊eeeeeeeeeeeee孔焊;小孑L 熔焊fffffffffffff 快速焊接feedrate of welding wire 焊丝送进速度field of welding temperature 焊接温度场field welding 现场焊接; 工地焊接Filler arc welding 菲拉电弧焊距fillet welding (填角焊)贴角焊fillet welding in the downhand position 船形角焊fillet welding in the flat position 船形焊fillet welding in the horizontal position 横角焊fillet welding in the vertical position 立角焊fine welding 精密焊接fine wire welding 细丝焊fire cracker welding 躺焊fire welding 锻焊; 锻接fixed welding machine 固定式焊机fixed-position welding 定位焊接flame welding 熔气焊flare welding 喇叭形坡口焊接flash butt welding 闪光对焊; 闪光对接焊flash welding 闪光电弧焊; 闪光焊; 闪焊; 火花电弧焊; 火花对焊flash-butt welding 电阻闪光焊接flashover welding 闪光焊flat position welding 平焊; 顶面平卧焊flat position welding of fillet weld 角焊缝平焊; 船形角焊flat welding 平卧焊flexible welding rod 软焊条flexible wire for electric welding 电焊软线flow welding 流注焊接; 浇焊fluid welding 流焊flux-cored welding 包芯焊条焊接fly-wheel type friction welding 贮能摩擦焊; 储能摩擦焊flywheel friction welding 惯性摩擦焊forehand welding 向前焊; 向左焊; 左焊法; 左向焊; 正手焊forge welding 锻焊; 锻接焊forward welding 正手焊; 左焊法; 左向焊; 前进焊; 前倾焊; 向前焊friction welding 摩擦焊; 摩擦焊接friction welding machine 摩擦焊接机frontal fillet welding 正面角焊full automatic welding 全自动焊fullautomatic arc welding 全自动电弧焊fullfillet welding 满角焊full-fusion thermit welding 热剂铸焊full-fusion welding 全熔合焊full-length welding 满焊fusion pressurewelding 熔化压接fusion thermit welding 热剂熔焊; 熔化铝热焊fusion type plasma arc welding 熔透型等离子弧焊fusion type welding 熔透型焊接法fusion welding 熔焊接fusion welding metal 熔焊金属gas carbon-arc welding 气保护碳弧焊gaselectric welding 气电联合焊接gas metal arc welding 气体保护金属极电弧焊gasmetal-arc welding 气保护金属极电弧焊gas shield welding 气体保护弧焊gas shielded arc welding 气体保护电弧焊; 气体保护焊gas shielded arc welding machine 气保护弧焊机gas shielded arc-welding machine 气体保护弧焊机gas shielded magnetic flux arc welding 磁性焊剂气体保护电弧焊gas shielded metal-arc welding 气体保护金属弧焊gas shielded welding 气体保护焊gas torch welding 气炬焊gas tungsten arc welding 气体保护钨极电弧焊gas tungsten-arc welding 气保护钨极电弧焊gas tungstun arc welding 钨极气体保护焊gas welding 气焊; 乙炔焊gas welding device 气焊设备gas welding equipment 气焊设备gas welding machine 气焊机gas welding outfit 气焊机gas welding rod 气焊焊丝gaswelding rubber hose 气焊橡胶管gaswelding technique 气焊工艺gaswelding torch butt 气焊进气硬管gaswelding tube mill 瓦斯焊接机gaswelding work 气焊工作gas-arcwelding 气电焊; 气体保护电弧焊gas-arcwelding gun 气电焊焊嘴gas-presswelding 气压焊gas-pressure welding machine 气压焊接机gas-shielded stud welding 气保护柱钉焊接girth welding 环缝横向焊接gravity type arcwelding 重力焊gravity type welding 倚焊gravity welding 重力焊; 重力式电弧焊groove welding 槽焊; 坡口焊; 开槽焊guided automatic welding 导向自动焊接gun welding machine 手提式点焊机; 点焊枪hafnium welding wire 铪焊丝hammer welding 锻焊; 锻接; 锤焊hammered resistance welding 锤锻电阻焊; 电阻加热锻焊handwelding holdet 手焊焊把hard-welding 硬质合金熔焊headlessbolt for welding 焊接单头螺栓heat-welding adhesive 热熔性胶粘剂heated-tool welding 热烙铁焊接heavy welding 大断面焊接heavy welding electrode 粗电焊条heliarc welding 氦电弧焊Heliarc welding 氦弧焊法helium arcwelding 氦弧焊HF welding magnetic bar 高频焊接磁棒hidden arcwelding 埋弧焊; 潜弧焊high current arc welding 大电流弧焊high frequency AC welding machine 高频交流电焊机high frequency dielectric welding 高频介电焊high frequency induction welding 高频感应焊high frequency welding 高频焊接high gradeenergywelding 高能焊high tensile electric welding rod 高强焊条high-current plasma arc welding 大电流等离子弧焊high-frequency induction welding 高频感应焊接; 高频焊接high-frequency resistance welding 高频接触焊high-frequency resistance welding (HFRW) 高频电阻焊high-frequency welding 高频电焊highspeedwelding 快速焊接horizontal fillet welding 横角焊; 水平角焊horizontal position welding 水平焊接; 横焊horizontal welding 横焊; 水平焊horizontalposition welding 水平位置焊接horizontal- rolledposition welding 水平转动焊接; 滚动水平焊hot jet welding 热风焊接hot presswelding 热压焊接hot pressurewelding 预热压力焊hot welding 热焊hot wire welding 热丝焊hot(-)gas welding 热气焊接hot-gas welding 热风焊接; 热空气焊接hot-pressure welding 热压焊; 热压焊接hydrogen-welding 氢焊impact spotwelding 冲击点焊法impregnated-tape metal-arc welding 浸焊条金属弧焊impulse current automatic butt welding machine脉冲电流自动对焊机impulse current seam welding machine 脉冲电流缝焊机impulse current semiautomatic butt welding machine 脉冲电流半自动对焊机impulse electromagnetic automatic welding machine 电磁脉冲自动焊机impulse plasma welding machine 脉冲等离子焊机impulse welding 脉冲焊; 脉冲焊接impulsed spot welding 脉冲点焊inclined position welding 倾斜焊indirect (spot) welding 单面点焊indirect welding 单面点焊induction welding 感应焊; 感应焊接; 感应熔焊inert gas arc spot welding 惰性气体电弧点焊inert gas arc welding 惰性气体电弧焊inert gas spot welding 惰性气体保护电弧点焊inert gas welding 惰性气体焊接法inert-gas (inert gas) arc welding 惰性气体保护焊inertia welding 惯性焊接; 贮能摩擦焊; 储能摩擦焊inertial welding 惯性焊接infrared welding 红外线焊接intermediate current plasma arc welding 中电流等离子弧焊intermittent fillet welding 断续角焊intermittent point welding 断续点焊intermittent welding 断续焊International Institute of welding (IIW) 国际焊接学会inverted welding 仰焊joint welding 搭焊jump welding 丁字形焊keyhole-mode welding 小孔型等离子弧焊; 穿透型焊接法lap fillet welding 搭角焊; 搭接角焊lap resistance welding 搭接电阻焊lap seamwelding 搭接缝焊; 搭接焊lap welding 搭焊; 搭接焊laser welding 激光焊接laser welding chamber 激光焊接室laser welding head 激光焊接头laser welding machine for orthodontics 激光口腔矫形焊接机laser welding system 激光焊接系统laser-beam welding machine 激光焊接机laser-welding machine 激光焊接器lead welding 铅焊lefthand welding 左焊法leftward welding 左向焊法lever gun welding head 杠杆式点焊钳light beam welding machine 光束焊机light continuous welding 轻连续焊接light gauge welding 薄板焊接light ray welding 光束焊接light welding 轻焊接Linde welding 林德钢管对焊法line welding 直线焊缝焊接liquid metal welding 浇注补焊longitudinal resistance seam welding 纵向电阻缝焊longitudinal seam welding 纵缝焊接; 纵向缝焊longitudinal welding 纵缝焊接; 纵向焊接low carbon steel welding electrode 低碳钢电焊条low carbon welding wires 低碳焊接线材low idle voltage arc-welding power supply 低空载电压的弧焊电源low temperature welding 低温焊接low- alloy steel covered arc welding electrode 低合金钢焊条low-current plasma arc welding 小电流等离子弧焊low-hydrogen welding electrode 低氢型电焊条low-temperature welding 低温焊接lowest permissible temperature for welding 焊接允许的最低温度machine for magnetic welding 磁力焊接机machine welding 机器焊接machine welding torch 机械焊接吹管magnetic discharge welding 电磁储能焊; 电磁焊magnetic flux arc welding 磁性焊剂电弧焊magnetic flux gas shielded arc welding 磁性焊剂气体保护电弧焊magnetic force welding machine 磁力焊接机magnetic-force welding 磁力焊接法manual arc welding 手工电弧堆焊manual electic arc pile up welding 手工电弧堆焊manual electric arc welding 手工电弧堆焊manual electro-slag welding 手工电渣焊manual gas welding 手工气焊manual metal-arc welding 手弧焊manual TIG welding 手工钨极惰性气体保护焊manual welding 手工焊接; 人工焊接manual welding machine 手工焊机manually coating welding electrode 手涂焊条mash seam welding 滚压电阻缝焊mash stitch welding 多针缝式焊接mask welding 电焊眼罩match assemble welding 装架焊接metal arc welding 金属电弧焊metal buried welding 埋渣焊multi-head automatic arc-welding machine 多头自动电弧焊机multi-head automatic welding machine 多头自动焊机multi-operator welding set 多站电焊机multi-pass (multiple pass) welding 多道焊multiarc welding 多弧焊multihead automatic arc welding machine 多弧自动电焊机multilayer welding 多层焊丝nickel covered welding eleetrode 镍药皮焊条nickel steel gas welding rod 镍钢气焊条nickel-base alloy bare weldingfiller metal 镍基合金焊丝nitrogen-arc welding 氮弧焊no-gas welding 非气焊non gas shielded arc welding 无气体保护电弧焊multioperator welding generator 多工位焊接发电机multioperator welding machine 多站电焊机; 多站焊机multioperator welding set 多站焊机multipass welding 多道焊接multiple arc welding 多弧焊non shielded arc welding 无保护电弧焊non-pressure welding 不加压焊接nonvacuum electron beamwelding 大气压电子束焊接non-welding character 不可焊接性nonpressure thermit welding (NTW) 热剂铸焊metal inert gas arc welding (MIG) 惰性气体金属电弧焊metal inert-gas arc welding 金属极惰性气体保护焊metal inertia gas welding 金属焊条惰性气体保护焊; 熔化极惰性气体保护焊metal rectifier welding set 整流焊机metalarc gas-shielded welding 气保护金属极电弧焊metal-arc gas-shielded welding (MAGSW) 金属极气保护焊metal-arc welding 金属极电弧焊micro resistance welding 显微电阻焊micro-gap welding 微间隙焊接microplasma arc welding 微束等离子弧焊micro-welding 微型焊接; 显微焊接microgap welding 微隙间隙焊Miebach high efficiency flash welding machine 米巴赫高效闪光对焊机mild steel arc welding electrode 低碳钢焊条mild steel welding rod 低碳钢焊丝miter welding 斜接头焊接mixed gas arc welding 混合气体保护电弧焊molten bath arc welding 熔池电弧焊molten-bath arc welding 熔池焊motor driven welding machine 电动焊机; 电动机拖动式焊机motor-driven welding machine 电动旋转式焊机motor-generator welding unit 电动直流发电焊接设备multiple operator arc weldingmachine 复式弧焊机multiple projection welding 多点凸焊multiple resistance welding 多点电阻焊接; 复式电阻焊multiple spot welding 多点点焊multiple spot welding machine 多点点焊机multiple-arc welding plant 多弧焊接机multiple-electrodemachine 多极点焊机multiple-electrodemultiple-impulse 脉冲接触焊multiple-operator 作焊接单元multiple-spotmultiple-wiresubmerged-arcmultiple-wire 多丝埋弧焊multiplewire 丝埋弧焊nail head narrowgap 面焊spot weldingwelding 多焊条焊接welding 多脉冲焊; 多welding-unit 多重操welding 多点焊multiple-power welding 多丝埋弧焊submerged arc weldingsubmerged-arc welding 多type welding 钉头式焊接oneside welding 窄间隙单narrow gapwelding 窄间隙单面自动电弧焊narrow gap welding 窄间隙焊接; 狭间隙焊negative polarity welding 反极性焊接neli-arc welding 氦电弧焊nickel bare welding filter metal 镍焊one-side automatic。
焊接常用词语英汉对照
焊接常用词语英汉对照actual weld-throat thick-ness焊缝厚度all-around weld整周焊缝all-around weld (整周焊缝)环焊缝angle butt weld斜对接焊angle weld角焊appearance of weld焊缝成形arc-seam weld电弧缝焊arc-spot weld电弧点焊arc-weld电弧焊aspect ratio of weld焊缝成形系数at weld edge在焊缝边上attachment weld连接焊缝automatic spot weld自动点焊法automatic weld自动焊接axis of a weld焊缝中心线; 焊接轴线axis of weld焊缝轴线; 焊接轴线back of weld焊缝背面backing groove of weld焊缝反面坡口backing weld底焊; 底焊焊缝bare metal arc weld裸焊条电弧焊bead weld珠焊; 堆焊bead-on-plate weld堆焊焊缝beading weld凸焊beam-to-beam weld梁间焊接; 梁式引线焊接block sequence weld分段多层焊bond weld钢轨接头焊接bridge seam weld桥缝焊接; 桥线焊brize weld硬焊butt weld对接焊缝butt weld ends对头焊接端butt-weld碰焊; 平式焊接; 对头焊接butt-weld in the downhand position对接平焊butt-weld joint对头焊接butt-weld pipe mill对焊管轧机button spot weld按电钮点焊cap weld最后焊层; 盖面焊缝carbon content of weld materials焊接材料的碳含量cast-weld construction铸焊结构caulk weld填缝焊caulking weld密实焊缝chain intermittent fillet weld链式分段角焊; 并列间断角焊缝chain intermittent weld并列焊接circular weld环形焊缝circumferential weld环缝; 环焊缝cleft weld裂口焊closed weld底边无缝焊; 无间隙焊缝closed-chamber fusion weld闭室熔焊cluster weld丛聚焊缝coil weld卷板对接焊; 卷板对接焊; 板卷焊cold weld冷压接commutator-controlled weld换向控制焊接complete penetration butt weld贯穿对焊composite weld紧密焊缝; 强度密封焊缝concave filled weld凹形角焊缝concave filler weld凹角焊concave fillet weld凹面填角焊concave weld凹焊缝; 凹面焊; 凹形焊缝; 轻型焊connective weld联系焊缝continuous butt-weld mill连续式炉焊管机组continuous fillet weld连续(填)角焊缝; 连续角焊缝; 连续贴角焊continuous weld连续焊缝continuous weld process连续式炉焊管法contour weld特形焊接convex fillet weld凸角焊缝; 凸形角焊缝convex weld凸焊缝; 凸形焊缝copper weld wire包铜钢丝corner flange weld单卷边角焊缝corner weld角焊corner-flange weld卷边角焊缝; 卷边角焊缝crack of weld焊部裂纹cross weld十字交叉焊缝; 横向焊缝cross-wire weld十字焊crotch weld楔接锻接; 楔接焊接cup weld带盖板焊缝depth of weld焊接深度dissimilar weld metal不同的焊接金属; 不同金属的焊接distance between the toes of a weld焊缝宽度double groove weld双面坡口焊缝double-bevel groove weld双斜边坡口焊缝; 双斜坡口焊double-flanged butt weld双弯边对接焊缝double-V groove weld双斜边坡口焊缝; 双斜坡口焊downhand weld平焊缝duplex spot weld双点点焊接头edge joint weld边缘焊edge weld端接焊; 端接焊缝; 端面焊缝; 对边焊electric resistance weld mill电阻焊管机electric weld-pipe mill电焊管机electric-weld pipe mill电焊管机emporary weld临时点定焊缝excess weld metal焊缝补强金属; 补强; 补强焊料; 补强金属excess weld metal(焊缝的)余高explosive weld爆炸焊接face of weld焊缝表面; 焊接面fibrous weld纤维状焊缝field weld现场焊接filler weld填角焊缝fillet weld角焊缝; 填角焊; 贴角焊fillet weld in normal shear (搭接接头的)正面角焊缝fillet weld in parallel shear侧面角焊缝; 侧面填角焊fillet weld in the flat position角接平焊; 水平角焊缝fillet weld in the horizontal position横向角焊缝fillet weld size焊角尺寸; 填角焊缝尺寸flame weld火焰焊接flange weld卷边焊缝; 卷边焊缝flange-to-web weld卷边焊缝; 卷边焊缝flanged butt weld弯边对接焊flanged edge weld卷边焊; 卷边焊flash butt weld闪光焊flash weld闪速对焊flat faced fillet weld平顶角焊缝焊接flat fillet weld平角焊ing of fillet weld角焊缝平焊; 船形角焊flush fillet weld平角焊flush weld削平补强的焊缝; 平焊接; 无加强高的焊缝forge weld锻焊焊缝forged weld (焊后锻压的)锻压焊缝form factor of the weld焊缝成形系数formation of weld焊缝成形front fillet weld正侧面填角焊缝; 正面填角焊front(al) fillet weld正面角焊缝full fillet weld满角焊缝; 全角焊full penetration butt weld满对接焊full weld满焊full-fillet weld满角焊full-sized weld全尺寸焊缝full-strength weld (与母材等强)等强焊缝gap weld特殊点焊; 双极单点焊gas-pressure weld气压焊girth weld环形焊缝gravity weld倚焊groove weld坡口焊; 坡口焊缝; 有坡口焊缝; 凹槽焊groove-weld joint有坡口焊接接头hammer weld锻焊hand weld手焊焊缝height of reinforcement of weld加强焊缝高度helical-weld pipe螺旋焊管high performance weld flux高性能焊剂horizontal fillet weld横向角缝焊接horizontal weld横向焊缝horizontal-vertical fillet weld横向垂直角焊缝hot weld encapsulation热焊封袋hydraulic automatic weld液压自动焊接hydraulic weld process液压焊接法inclined weld斜焊inconel weld单面焊缝incorrect weld profile焊缝形状不对incorrect weld size焊缝尺寸不对induction weld mill感应焊管机inside corner weld内角焊接inside fillet weld内角焊接inside weld内焊缝insufficient or excess reinforcement of weld加强焊缝不足或过量intermittent fillet weld间断角缝焊接; 断续角焊缝intermittent weld断续焊; 断续焊缝jam weld对接焊; 对头焊接lap fillet weld搭接角焊缝laser (beam) weld (ing)激光焊lateral weld侧焊; 侧面焊缝leg of a fillet weld角焊缝; 角焊缝焊脚leg of fillet weld圆角焊肉厚length of weld焊缝长度light closing weld轻连续焊接light fillet weld轻型填角焊; 小填角焊light weld轻焊缝Lincoln weld埋弧自动焊longitudinal fillet weld纵向角焊longitudinal weld纵向焊缝longitudinal weld (焊接用语)纵缝loose weld脱焊main weld主焊缝mash seam weld压薄缝焊; 滚压焊mash weld点焊; 点压焊melt thru weld熔透焊缝melt-through weld透溶焊melten weld pool焊接熔池melting through weld熔透焊缝miter weld平顶角焊缝; 斜接角焊缝molten weld metal熔融焊接金属mulitple impulse weld多脉冲焊缝multilayer weld多层焊缝multipass weld多道焊缝multiple arc weld多弧焊缝multiple-electrode submerged arc weld多电极埋弧焊multiple-pass weld多道焊缝; 多路焊接multirun weld多道焊缝nonpressure thermit weld不加压热剂焊缝normal weld正常焊接oblique fillet weld斜交角焊缝; 斜角焊接one-pass weld单层焊缝open butt weld开口对接焊open weld留间隙焊缝; 空隙焊outside weld外焊缝over weld过焊overhead fillet weld仰焊角焊缝overhead weld仰焊oversize weld超尺寸焊缝oxygen weld氧气焊接parallel-arc weld并列弧焊patch weld补焊; 补孔焊缝Peltier's cross weld珀耳帖交叉焊接penetration weld熔透焊缝percussion weld冲击焊缝; 冲击焊接periphera weld环形焊缝pitch of weld焊缝接距; 焊线距plain butt weld无坡口对接焊; 平头对接焊缝plasma-arc weld等离子弧焊接plug weld塞焊焊缝point of weld焊接点point weld点焊poor weld劣质焊缝; 有缺陷的焊缝porous weld多孔焊缝; 疏松焊缝positioned weld平位焊缝; 暂焊post weld annealed (PWA)焊后退火poured weld铸焊焊缝powder weld process粉末焊接法practice weld试验焊缝pressure weld压焊pressure-controlled weld压力控制焊接pressure-tight weld气密焊; 密封焊道principal weld主要焊缝profile of fillet weld填角焊缝轮廓progress of weld焊向projection weld凸焊; 凸焊焊缝projection weld machine凸点电阻焊机pulsating weld脉冲接触焊push weld挤焊quilting weld钉焊reinforced butt weld补强的对接焊缝; 补强式对接焊缝reinforced weld加强焊接reinforcement of weld焊缝加厚; 补强金属; 加强焊缝resistance weld mill电阻焊管机resistance weld pipe电阻焊管resonance butt weld谐振式对接焊restarting a weld再引弧ripple weld鳞状焊缝rivet weld电铆; 电铆焊缝root face of weld焊缝根部钝边root gap of weld焊缝根部间隙root of weld焊缝根部; 焊根root opening of weld焊缝根部间隙root radius of weld焊缝坡口根部半径sagged weld下垂焊缝scarf weld楔口焊接seal weld填焊; 致密焊缝; 密封焊; 密封焊道; 密封焊缝sealing weld封焊seam weld滚焊semi-automatic arc weld半自动电弧焊sequence weld timer序列焊接时间调节器shallow weld浅焊shop weld工厂焊接shot weld点焊shoulder of weld焊缝根部钝边side fillet weld侧面角焊缝; 侧面填角焊缝; 侧面贴角焊side lap weld侧边搭接焊; 弯边搭焊缝side weld侧焊缝; 边焊single lap weld单搭接焊single strap butt weld单面盖板对接焊single-bevel groove weld单斜角槽焊single-fillet weld单边角接焊缝single-pass weld单道焊site weld现场焊接; 安装焊; 安装焊接size of a fillet weld焊角尺寸size of weld焊件的大小; 焊区尺寸skew weld斜焊skin weld表面焊接sleeve weld套筒焊接slip-weld hanger卡瓦焊接套管挂slot weld槽塞焊; 长孔焊; 开槽搭焊缝; 切口焊缝ing slotted weld槽焊slotted lap weld切口搭接焊smooth fillet weld平填角焊缝socket weld ends承插焊接端soft-weld铜镍焊条合金solvent weld溶剂焊接space of intermittent weld断续焊缝间距; 断续焊间距spiral weld螺旋形焊缝spiral weld-pipe mill螺旋焊管机spot weld焊点spot weld bonding胶结点焊spot weld nugget点焊熔核spreading weld宽缝焊接; 加宽的焊缝square butt weld平头对接焊缝square groove weld无坡口槽焊staggered intermittent fillet weld (ing)交错断续角焊staggered intermittent weld交错断续焊缝; 交错间断焊staggered plug weld交错塞焊standard reinforced fillet weld标准加强角焊缝stick-out weld未熔合点焊接头stitch-and-seam weld点线焊straight butt weld无坡口对接接头strapped weld搭板对接焊缝strength weld受载焊缝; 强固焊接; 承载焊缝; 高强度焊接structural weld强固焊缝surface of weld焊缝表面surface weld表面焊缝surface weld metal buildup表面焊缝金属的形成synthetic apparatus for weld thermal cycle焊接热循环模拟装置T weld丁字接头焊缝T-filled weld丁字形角焊T-fillet weld丁字接头角焊缝tack weld定位焊点; 定位焊缝; 临时点焊; 预焊; 平头焊接(welding)定位焊tandem arc weld前后弧焊temporary weld临时点固焊缝tension weld受拉焊缝test weld试焊throat depth (thickness) of fillet weld角焊缝厚度throat of fillet weld凹角焊喉; 填角焊缝喉长throat of weld凹角焊喉tight weld密封焊接; 致密焊缝tight-strong weld密实强固焊缝toe of the weld焊缝边界toe of weld焊趾toe weld趾部焊缝torch weld气焊焊缝total amount of weld fumes焊接发尘量transverse fillet weld横向角焊缝; 正面角焊transverse weld横向焊缝trial weld试验焊接undercut weld底切焊接undressed weld (增加焊缝)未加工焊缝unequal fillet weld焊脚不等的角焊缝unfitness of butt weld焊缝对口错边量union-melt weld埋弧焊unload weld非承载焊缝unspaced butted weld无间隙对接焊缝upgrading of boiler weld锅炉焊缝加强vertical fillet weld立焊角焊缝vertical weld立焊weak weld不强固焊缝weaving weld横向摆动焊缝weld焊; 焊接的; 补焊weld all around围焊weld appearance焊缝外观weld assembly焊接组件weld back-up焊缝背垫weld backing焊缝衬垫weld bead焊缝; 熔敷焊道weld bead height焊缝高度weld beading焊瘤weld bond熔合线weld bridge seam搭桥焊缝; 桥接焊缝weld cap焊帽weld center line焊缝中心线weld collar加强焊缝焊瘤weld crack焊接裂纹weld crater熔池weld crosswise交叉焊接weld decay焊缝腐蚀; 焊接接头晶间腐蚀; 焊接侵蚀; 焊接区晶间腐蚀weld decay (焊接后)敏化区腐蚀weld defect焊接缺陷weld delay time焊接延迟时间weld deposit堆焊weld deposits cleaning焊接熔敷金属清理weld edge焊缝边缘; 焊缝表面边缘weld edgewise沿边焊接weld flange connection焊接法兰连接weld flash焊瘤weld flaw焊接缺陷weld flush焊缝隆起weld fumes焊接烟尘weld gage焊缝检查规; 焊缝卡规weld gauge焊缝量规weld heat input焊接热输入; 焊接线能量weld holder焊接夹持架; 焊接架weld inspection焊缝质量检验; 焊接检查weld interface焊缝界面; 焊接界面weld interval焊接时间weld is accepted焊缝合格weld jig焊接夹具weld joint焊缝weld junction熔焊线; 熔合线weld layer焊接层weld length焊缝长度weld line焊缝线; 焊缝轴线; 焊接线; 焊线weld machined flush削平补强的焊缝weld mark焊缝符号; 焊缝记号; 焊接痕; 熔缝weld mesh crate焊接网格weld metal焊缝金属; 焊接金属weld metal buildup surface金属堆焊表面weld metal composition焊接金属组成weld metal cracking焊缝裂纹weld metal zone焊缝金属区; 焊接金属熔化区weld nugget焊点熔核weld on bottom底焊weld overlap重叠区weld pass焊接通道weld penetration焊缝熔深; 焊透深度weld period焊接时间weld pitch焊缝距weld porosity焊缝气孔weld preheating焊前预热weld preparation焊缝坡口加工weld puddle熔池weld reinforcement焊缝补强; 焊缝加强; 焊接补强weld repairs焊接修补weld ripple焊缝波纹weld root焊件剖口; 焊接根weld root opening gap焊缝根部间隙weld root reinforcement焊缝反面加强weld rotation焊缝转角weld seam pipe焊缝管weld shape焊缝形状weld shielding焊接区保护; 焊接熔池保护weld slope焊缝倾角weld spacing焊点距; 焊缝间距weld strain焊接应变weld strength焊接强度weld surface焊缝表面weld swell焊缝隆起weld thermal cycle焊接热循环weld thickness焊缝厚度weld time焊接时间; 焊接通电时间; 接触焊通电时间weld toxic gases焊接有害气体weld trimmer焊缝清理机weld up焊补weld wheel conditioner焊轮调节器weld width焊缝宽度weld wire包铜钢丝weld zone焊缝区; 焊接区weld-form factor焊缝形状系数weld-fusion line焊缝熔合线weld-in nozzle焊入式喷嘴weld-interval timer焊接间隔记时器weld-shrunk cylinder包扎式圆筒weld-shrunk multilayered cylinder包扎式多层圆筒; 多层包扎式圆筒weld-throat thickness depth焊缝厚度window type restraint weld cracking test窗口拘束焊缝抗裂试验; 窗形拘束抗裂试验zigzag intermittent fillet weld锯齿形断续角焊缝; 锯齿形断续角焊缝zone of weld焊缝表面AC & D. C. arc welding machine交直流弧焊机AC arc welding交流电弧焊AC gas metal-arc welding process交流熔化极气保护焊AC gas tungsten arc welding交流钨极气保护焊AC welding set交流焊机; 交流焊接变压器AC-dc welding machine交直流两用焊机acetylene welding气焊; 乙炔焊; 乙炔焊接acetylene welding torch乙炔焊炬; 乙炔接焊吹管air-acetylene welding空气-乙炔焊接all-position welding全位置焊接alloy steel gas welding rod合金钢气焊条alternating current arc welding交流电弧焊alternating current welding machine交流电焊机aluminium alloy arc welding electrode铝合金焊条aluminothermic welding铝热焊; 铸焊angle backwards welding后倾焊angle butt welding斜口对接焊angle forwards welding前倾焊annealing welding wave退火焊波antogenous welding氧炔焊apparatus for butt welding平接压焊夹具arc braze welding电弧钎焊arc flash welding电弧闪光焊arc spot welding电铆焊arc stud welding柱钉电弧焊; 螺柱电弧焊arc voltage feedback controlling arc welding弧压反馈电弧焊arc welding电弧焊; 电弧焊接; 弧焊arc welding electrode电弧焊条arc welding generator电弧焊接用发电机; 弧焊发电机arc welding generator with independent excitation自激弧焊发电机; 他激电焊发电机arc welding generator with self-excitation自激电焊发电机arc welding machine弧焊机; 电焊机; 电弧焊机arc welding mask电弧焊遮罩arc welding process电弧焊接工艺过程arc welding rectifier弧焊整流器arc welding robot弧焊机器人arc welding set电弧焊机组arc welding transformer弧焊变压器arc-welding electrode电弧焊用焊条arc-welding plant电焊厂arcogen welding电弧氧乙炔焊argon (shielded) arc welding氩弧焊接argon tungsten-arc welding钨极氩弧焊argon-arc welding氩弧焊argonaut welding自动氩弧焊atomic H welding氢原子焊atomic hydrogen welding原子氢焊atomic-hydrogen welding原子氢焊接austenite welding不锈钢焊接autogenous pressure welding自动压合热焊autogenous welding气焊automatic arc welding head自动电弧焊接机头automatic arc welding machine自动电焊机; 自动弧焊机automatic drying line for welding electrode电焊条自动烘焙线automatic slag pool welding自动电渣焊automatic spot welding自动点焊automatic submerged arc welding自动埋弧焊automatic submerged slag welding of rail钢轨automatic submerged-arc welding machine埋弧自动焊机automatic transverse welding横向自动焊automatic welding自动焊; 自动焊接automatic welding head自动焊头automatic welding machine自动焊接机automatic welding of circumferential seams环缝自动焊automatic welding process自动焊接工艺规程automation of welding焊接自动化back hand welding后退焊; 反手焊接back step welding反手焊接back ward welding反手焊接back welding底焊; 退焊法back-step welding分段退焊法backhand welding逆向焊; 右焊法; 后焊法; 向后焊backing welding打底焊backstep welding分段逆焊; 分段退焊; 反向焊; 逐步退焊法; 逆向焊backstep welding sequence分段退焊次序backward welding后倾焊; 后退焊; 向右焊balanced welding对称焊bare welding rod光焊条bare wire arc welding光焊丝电弧焊bead welding窄焊道焊接bench arc welding machine台式弧焊机bevel welding斜角焊blacksmith welding锻工焊接; 锻焊block sequence welding分段多层焊; 分段连续焊接block welding块焊接block welding sequence分段多层焊body welding machine罐身焊接机both sides welding双面焊接brass welding rod黄铜焊条braze welding钎焊; 钎焊接; 钎接; 铜焊braze-welding钎接焊bridge spot welding带接合板点焊; 单面衬垫点焊; 单面搭板点焊bridge welding桥接焊; 盖板焊brize welding硬焊build (built) up welding堆焊build-up welding堆焊building-up by welding堆焊butt resistance welding电阻对焊; 对接电阻焊butt seam welding对接滚焊butt seam welding machine对接缝焊机butt welding对接焊; 平对焊butt welding machine对接焊机butt welding process对接焊法butt-welding对接焊butt-welding machine对焊机capability of welding vertically upwards直上焊接能力capacitor-discharge welding电容放电焊接carbon arc welding碳弧焊; 碳极弧焊carbon in materials for welding焊接用材料中的碳carbon-dioxide arc welding二氧化碳保护焊carriage of automatic welding machine自动焊机走架cascade welding阶梯式焊; 山形多层焊cascade welding sequence串级叠置法cast welding铸焊cement-welding金属陶瓷焊接centralized installation of welding machine多站焊接chain intermittent fillet welding并列断续角焊缝; 链式断续角焊chemical welding化学焊circular seam welding环缝对接焊circular seam-welding machine环形滚焊机cleaning before welding焊接前的清理cleaning of welding deposits焊接沉积的清理closed butt gas pressure welding闭式加压气焊cold welding冷焊; 冷压焊cold-pressure welding冷压焊combined cutting and welding torch焊割两用炬combined cutting and-welding blow-pipe焊割两用炬combined thermit welding加压铸焊complete penetraction and fusion in welding全焊透condenser (discharge) spot-welding machine电容器放电点焊机condenser discharge spot welding电容储能点焊; 电容贮能点焊constant current welding machine恒流电焊机constant energy welding machine恒功率电焊机constant voltage welding machine恒压电焊机constant-current arc welding power source垂降特性弧焊电源constant-current welding source恒流式焊接电源constant-power welding source恒功率式焊接电源constant-pressure pressure welding恒压压力焊constant-temperature pressure welding恒温压力焊constant-voltage welding machine恒电压焊机constant-voltage welding source恒压式焊接电源; 平特性焊接电源consumable electrode welding熔化极电弧焊consumable guide electroslag welding自耗定向电渣焊contact welding接触焊continuous feed welding连续送丝电弧焊continuous welding连续焊; 连续焊接contour welding绕焊controlled arc welding可控电弧焊接controlled atmosohere arc welding充气室电弧焊controlled atmospere arc welding充气式电弧焊controlled tungsten-arc welding自动控制弧长的钨极电弧焊controlled-transfer welding可控过渡电弧焊convex fillet welding凸面角焊缝copper arc welding electrode铜焊条copper welding rod铜焊条copper-alloy arc welding electrode铜合金焊条copper-aluminium welding rod铜铝焊条copper-nickel welding rod铜镍焊条copper-silicon welding rod铜硅焊条copper-tin welding rod铜锡焊条copper-zinc welding rod铜锌焊条core welding-wire焊芯core wire for welding rod焊条芯线corrosion due to welding焊接腐蚀cosmetic welding盖面焊cover chain welding链节式药皮包丝焊接CO 2 arc welding machine二氧化碳弧焊机cracking test for automatic welding自动焊抗裂试验crankshaft flashbutt welding曲轴电阻弧花压焊cross welding横向焊缝cyc-arc welding圆环电弧焊deck welding重力焊deep fillet welding深角焊deep penetration welding深熔焊deep penetration welding electrode深熔焊条deep welding深焊die welding模焊; 冲模堆焊diesel engine driven DC arc welding machine柴油机驱动直流弧焊机differential-excited welding generator差激电焊发电机diffusion welding扩散焊接direct spot welding双面点焊direct welding双面点焊direction of welding焊接方位; 焊接方向discontinuous welding断续焊dot welding点焊double carbon-arc welding间接碳弧焊double side welding双面焊接down-hand welding俯焊downhand welding平焊downward welding in the inclined position下坡焊downward welding in the vertical position向下立焊dual-arc welding双弧焊edge seam welding端面接头滚焊edge welding边缘焊接edgewise welding沿边焊接electric and pressure welding电压力焊接electric arc spot welding电弧点焊electric arc welding generators电弧焊接发电机electric arc welding machine电弧焊机electric butt welding电阻接触焊electric resistance welding电阻焊接; 热电阻焊electric slag welding电渣焊electric spot welding电点焊electric welding电焊electric welding cast copper solder铸铜电焊条electric welding equipment电焊设备electric welding generator电焊发电机electric welding hammer电焊锤electric welding machine电焊机electric welding plant电焊厂electric welding pliers电焊钳electric welding rod电焊条electric welding strip电焊片electric-arc welding电弧焊electric-resistance seam-welding电阻缝焊electric-resistance seam-welding machine电阻缝焊机electrical arc welding电弧焊接electrical resistance welding tube电阻焊接管electrically heated welding torch电热焊枪electro-beam welding电子束焊接electro-gas (enclosed) welding气电立焊electro-slag welding电磁渣焊; 电渣焊electro-slag welding with plate electrode板极电渣焊electro-welding电焊electrode for arc welding电焊条; 电弧焊条electrode for vertical down welding向下立焊条electrode of vertical down welding立向下焊条electrode welding电弧焊electrogas welding气电焊; 电气焊electromagnetic percussive welding电磁冲击焊electromagnetic stored energy welding电磁储能焊electron beam welding电子束焊; 电子束焊接electron beam welding machine电子束焊接机electron-beam welding电子束焊接electron-beam welding machine电子束焊机electron-bombardment welding真空电子束焊electrons leaves welding电子束焊接electropercussive welding电冲击焊; 冲击焊; 储能焊electroslag welding电渣焊; 电阻焊electroslag welding machine电渣焊机electroslag welding with consumable nozzle熔嘴电渣焊electroslag welding with wire electrode丝极电渣焊electrostatic (percussive) welding电能储能焊接electrostatic percussing welding静电焊; 静电焊; 冲击焊; 储能焊electrostatic percussive welding静电冲击焊; 静电冲击焊enclosed welding强制成形焊接energy storage welding贮能焊; 储能焊; 脉冲焊接erecting welding装配焊接erection welding安装焊接eutectic welding低温焊exothermic welding铝热焊expanding or welding of tube with tubesheet管子与管板的胀接或焊接explosive welding (EW)爆炸焊eyelet welding孔焊; 小孔熔焊faster welding快速焊接feed rate of welding wire焊丝送进速度field of welding temperature焊接温度场field welding现场焊接; 工地焊接Filler arc welding菲拉电弧焊距fillet welding (填角焊)贴角焊fillet welding in the downhand position船形角焊fillet welding in the flat position船形焊fillet welding in the horizontal position横角焊fillet welding in the vertical position立角焊fine welding精密焊接fine wire welding细丝焊fire cracker welding躺焊fire welding锻焊; 锻接fixed welding machine固定式焊机fixed-position welding定位焊接flame welding熔气焊flare welding喇叭形坡口焊接flash butt welding闪光对焊; 闪光对接焊wire welding焊网flash welding闪光电弧焊; 闪光焊; 闪焊; 火花电弧焊; 火花对焊flash-butt welding电阻闪光焊接flashover welding闪光焊flat position welding平焊; 顶面平卧焊flat position welding of fillet weld角焊缝平焊; 船形角焊flat welding平卧焊flexible welding rod软焊条flexible wire for electric welding电焊软线flow welding流注焊接; 浇焊fluid welding流焊flux-cored welding包芯焊条焊接fly-wheel type friction welding贮能摩擦焊; 储能摩擦焊flywheel friction welding惯性摩擦焊forehand welding向前焊; 向左焊; 左焊法; 左向焊; 正手焊forge welding锻焊; 锻接焊forward welding正手焊; 左焊法; 左向焊; 前进焊; 前倾焊; 向前焊friction welding摩擦焊; 摩擦焊接friction welding machine摩擦焊接机frontal fillet welding正面角焊full automatic welding全自动焊full-automatic arc welding全自动电弧焊full-fillet welding满角焊full-fusion thermit welding热剂铸焊full-fusion welding全熔合焊full-length welding满焊fusion pressure welding熔化压接fusion thermit welding热剂熔焊; 熔化铝热焊fusion type plasma arc welding熔透型等离子弧焊fusion type welding熔透型焊接法fusion welding熔焊接fusion welding metal熔焊金属gas carbon-arc welding气保护碳弧焊gas electric welding气电联合焊接gas metal arc welding气体保护金属极电弧焊gas metal-arc welding气保护金属极电弧焊gas shield welding气体保护弧焊gas shielded arc welding气体保护电弧焊; 气体保护焊gas shielded arc welding machine气保护弧焊机gas shielded arc-welding machine气体保护弧焊机gas shielded magnetic flux arc welding磁性焊剂气体保护电弧焊gas shielded metal-arc welding气体保护金属弧焊gas shielded welding气体保护焊gas torch welding气炬焊gas tungsten arc welding气体保护钨极电弧焊gas tungsten-arc welding气保护钨极电弧焊gas tungstun arc welding钨极气体保护焊gas welding气焊; 乙炔焊gas welding device气焊设备gas welding equipment气焊设备gas welding machine气焊机gas welding outfit气焊机gas welding rod气焊焊丝gas welding rubber hose气焊橡胶管gas welding technique气焊工艺gas welding torch butt气焊进气硬管gas welding tube mill瓦斯焊接机gas welding work气焊工作gas-arc welding气电焊; 气体保护电弧焊gas-arc welding gun气电焊焊嘴gas-press welding气压焊gas-pressure welding machine气压焊接机gas-shielded stud welding气保护柱钉焊接girth welding环缝横向焊接gravity type arc welding重力焊gravity type welding倚焊gravity welding重力焊; 重力式电弧焊groove welding槽焊; 坡口焊; 开槽焊guided automatic welding导向自动焊接gun welding machine手提式点焊机; 点焊枪hafnium welding wire铪焊丝hammer welding锻焊; 锻接; 锤焊hammered resistance welding锤锻电阻焊; 电阻加热锻焊hand welding holdet手焊焊把hard-welding硬质合金熔焊headless bolt for welding焊接单头螺栓heat-welding adhesive热熔性胶粘剂heated-tool welding热烙铁焊接heavy welding大断面焊接heavy welding electrode粗电焊条heliarc welding氦电弧焊Heliarc welding氦弧焊法helium arc welding氦弧焊HF welding magnetic bar高频焊接磁棒hidden arc welding埋弧焊; 潜弧焊high current arc welding大电流弧焊high frequency AC welding machine高频交流电焊机high frequency dielectric welding高频介电焊high frequency induction welding高频感应焊high frequency welding高频焊接high grade energy welding高能焊high tensile electric welding rod高强焊条high-current plasma arc welding大电流等离子弧焊high-frequency induction welding高频感应焊接; 高频焊接high-frequency resistance welding高频接触焊high-frequency resistance welding (HFRW)高频电阻焊high-frequency welding高频电焊highspeed welding快速焊接horizontal fillet welding横角焊; 水平角焊horizontal position welding水平焊接; 横焊horizontal welding横焊; 水平焊horizontal-position welding水平位置焊接horizontal-rolledposition welding水平转动焊接; 滚动水平焊hot jet welding热风焊接hot press welding热压焊接hot pressure welding预热压力焊hot welding热焊hot wire welding热丝焊hot(-)gas welding热气焊接hot-gas welding热风焊接; 热空气焊接hot-pressure welding热压焊; 热压焊接hydrogen-welding氢焊impact spot welding冲击点焊法impregnated-tape metal-arc welding浸焊条金属弧焊impulse current automatic butt welding machine脉冲电流自动对焊机impulse current seam welding machine脉冲电流缝焊机impulse current semiautomatic butt welding machine脉冲电流半自动对焊机impulse electromagnetic automatic welding machine电磁脉冲自动焊机impulse plasma welding machine脉冲等离子焊机impulse welding脉冲焊; 脉冲焊接impulsed spot welding脉冲点焊inclined position welding倾斜焊indirect (spot) welding单面点焊indirect welding单面点焊induction welding感应焊; 感应焊接; 感应熔焊inert gas arc spot welding惰性气体电弧点焊inert gas arc welding惰性气体电弧焊inert gas spot welding惰性气体保护电弧点焊inert gas welding惰性气体焊接法inert-gas (inert gas) arc welding惰性气体保护焊inertia welding惯性焊接; 贮能摩擦焊; 储能摩擦焊inertial welding惯性焊接infrared welding红外线焊接intermediate current plasma arc welding中电流等离子弧焊intermittent fillet welding断续角焊intermittent point welding断续点焊intermittent welding断续焊International Institute of welding (IIW)国际焊接学会inverted welding仰焊joint welding搭焊jump welding丁字形焊keyhole-mode welding小孔型等离子弧焊; 穿透型焊接法lap fillet welding搭角焊; 搭接角焊lap resistance welding搭接电阻焊lap seam welding搭接缝焊; 搭接焊lap welding搭焊; 搭接焊laser welding激光焊接laser welding chamber激光焊接室laser welding head激光焊接头laser welding machine for orthodontics激光口腔矫形焊接机laser welding system激光焊接系统laser-beam welding machine激光焊接机laser-welding machine激光焊接器lead welding铅焊lefthand welding左焊法leftward welding左向焊法lever gun welding head杠杆式点焊钳light beam welding machine光束焊机light continuous welding轻连续焊接light gauge welding薄板焊接light ray welding光束焊接light welding轻焊接Linde welding林德钢管对焊法line welding直线焊缝焊接liquid metal welding浇注补焊longitudinal resistance seam welding纵向电阻缝焊longitudinal seam welding纵缝焊接; 纵向缝焊longitudinal welding纵缝焊接; 纵向焊接low carbon steel welding electrode低碳钢电焊条low carbon welding wires低碳焊接线材low idle voltage arc-welding power supply低空载电压的弧焊电源low temperature welding低温焊接low-alloy steel covered arc welding electrode低合金钢焊条low-current plasma arc welding小电流等离子弧焊low-hydrogen welding electrode低氢型电焊条low-temperature welding低温焊接lowest permissible temperature for welding焊接允许的最低温度machine for magnetic welding磁力焊接机machine welding机器焊接machine welding torch机械焊接吹管magnetic discharge welding电磁储能焊; 电磁焊magnetic flux arc welding磁性焊剂电弧焊magnetic flux gas shielded arc welding磁性焊剂气体保护电弧焊magnetic force welding machine磁力焊接机magnetic-force welding磁力焊接法manual arc welding手工电弧堆焊manual electic arc pile up welding手工电弧堆焊manual electric arc welding手工电弧堆焊manual electro-slag welding手工电渣焊manual gas welding手工气焊manual metal-arc welding手弧焊manual TIG welding手工钨极惰性气体保护焊manual welding手工焊接; 人工焊接manual welding machine手工焊机manually coating welding electrode手涂焊条mash seam welding滚压电阻缝焊mash stitch welding多针缝式焊接mask welding电焊眼罩match assemble welding装架焊接metal arc welding金属电弧焊metal buried welding埋渣焊metal inert gas arc welding (MIG)惰性气体金属电弧焊metal inert-gas arc welding金属极惰性气体保护焊metal inertia gas welding金属焊条惰性气体保护焊; 熔化极惰性气体保护焊metal rectifier welding set整流焊机metal-arc gas-shielded welding气保护金属极电弧焊metal-arc gas-shielded welding (MAGSW)金属极气保护焊metal-arc welding金属极电弧焊micro resistance welding显微电阻焊micro-gap welding微间隙焊接micro-plasma arc welding微束等离子弧焊micro-welding微型焊接; 显微焊接microgap welding微隙间隙焊Miebach high efficiency flash welding machine米巴赫高效闪光对焊机mild steel arc welding electrode低碳钢焊条mild steel welding rod低碳钢焊丝miter welding斜接头焊接mixed gas arc welding混合气体保护电弧焊molten bath arc welding熔池电弧焊molten-bath arc welding熔池焊motor driven welding machine电动焊机; 电动机拖动式焊机motor-driven welding machine电动旋转式焊机motor-generator welding unit电动直流发电焊接设备multi-head automatic arc-welding machine多头自动电弧焊机multi-head automatic welding machine多头自动焊机multi-operator welding set多站电焊机multi-pass (multiple pass) welding多道焊multiarc welding多弧焊multihead automatic arc welding machine多弧自动电焊机multilayer welding多层焊multioperator welding generator多工位焊接发电机multioperator welding machine多站电焊机; 多站焊机multioperator welding set多站焊机multipass welding多道焊接multiple arc welding多弧焊multiple operator arc welding machine复式弧焊机multiple projection welding多点凸焊multiple resistance welding多点电阻焊接; 复式电阻焊multiple spot welding多点点焊multiple spot welding machine多点点焊机multiple-arc welding plant多弧焊接机multiple-electrode spot welding machine多极点焊机multiple-electrode welding多焊条焊接multiple-impulse welding多脉冲焊; 多脉冲接触焊multiple-operator welding-unit多重操作焊接单元multiple-spot welding多点焊multiple-wire multiple-power submerged-arc welding多丝埋弧焊multiple-wire submerged arc welding多丝埋弧焊multiplewire submerged-arc welding多丝埋弧焊nail head type welding钉头式焊接narrow gap one side welding窄间隙单面焊narrow gap one-side automatic welding窄间隙单面自动电弧焊narrow gap welding窄间隙焊接; 狭间隙焊negative polarity welding反极性焊接neli-arc welding氦电弧焊nickel bare welding filter metal镍焊丝nickel covered welding eleetrode镍药皮焊条nickel steel gas welding rod镍钢气焊条nickel-base alloy bare welding filler metal镍基合金焊丝nitrogen-arc welding氮弧焊。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
裂纹
Cracking
磁粉探伤
Magnetic particle
气孔
Porosity
着色渗透探伤
Dye penetrant
夹渣
slag inclusion
管材涡流检测
Eddy current
飞溅
Spatter
X光射线探伤
Radiographic
咬边
UnSubmerged arc weld
多道焊缝
Multiple-pass weld
仰焊
Underside welding
电焊机
Arc welder
平焊
Downward welding
堆焊
Overlaying welding
点焊
Pinpoint welding
立焊
Vertical position welding
塌陷(未填满)
Underfill
凸度
convexity
凹度
Concave
焊脚不等
Unequal leg for fillet weld
焊缝表面粗糙
Rough weld surface
电弧擦伤
Arc strike
对接
Butt
角焊
Corner
搭接
Lap
卷边焊
Edge
T型焊
T
可焊性
Weldability
埋弧焊
焊瘤
Overlap
拉伸
Tensile
弧坑
Crater
冲击
Impact
未焊透
Insufficient penetration
剪切
Shear
单面错边
Mismatch for single weld
韧性
toughness
双面错边
Mismatch for double weld
坡口
groove
余高
Face reinforcement
对称焊
Symmetry welding
X光探伤
Radiography
磁粉探伤
Magnetic particle
着色探伤
Penetrant
压弯
Bend
宏观检查
Macro
惰性气体保护碳弧焊接
Inert gas carbon arc weld
二氧化碳气体保护焊接
Carbon dioxide gas arc welding