Husky 气动隔膜泵 彩页
美国固瑞克716的技术参数
美国固瑞克716的详细信息
HUSKY716气动双隔膜泵:
性能：防爆、耐腐蚀、无泄露
最大工作流体压力:0.7兆帕(100psi，7巴)
工作空气压力范围:0.18～0.7兆帕（25～100psi,1.8～7巴）最大空气消耗量:0.672立方米/分（28scfm）
最大自由流量:61升/分（16加仑/分）
最大往复速度干抽:400循环/分
最大虹吸高度干抽:4.5米(15英尺)
湿抽:7.6米(25英尺)
每行程流量:0.075升（0.02加仑）
每往复流量:0.15升（0.04加仑）
最大输送固体颗粒:2.5毫米（3/32英寸）
空气进口尺寸:1/4英寸NPT（F）
空气出口尺寸:3/8英寸NPT（F）
流体进口尺寸:3/4英寸NPT（F）/BSP（F）
流体出口尺寸:3/4英寸NPT（F）/BSP（F）
浸液部件铝合金泵:铝合金，SST，TEFLON
重量铝泵:3.9千克（8.5英镑）
驱动方式：气动。
气动液压电动泵的工作原理和组成解读
Haskel气动液压电动泵工作原理和组成Haskel气动液体泵由气体驱动部分，液压部分和换向控制阀三个部分组成。
气体驱动部分的活塞和液压部分的柱塞连在一起，由换向阀控制自动做往复运动。
通过大面积的活塞和小面积的柱塞，将作用在活塞上的驱动气体的压强传递给柱塞，从而提高液体的出口压力。
Haskel气动液体泵的特点：以普通压缩空气或其它气体作为动力连续起停，不受限制最高压力可达：6800BAR适用于绝大多数介质无需任何润滑油产品范围广不产生热量和火花体积小Haskel气动液体泵型号字母代码：M 1"冲程，1/3HP泵系列XH2"冲程，1.5+2HP超高压泵系列S 不锈钢柱塞和泵体G 4-1/2"冲程，6HP泵系列29723 1/3HP化学泵84-1/2"冲程，8HP泵系列D（前缀）液体端加长的泵144"冲程，10HP泵系列D（后缀）双作用泵W聚氨脂U型密封4B 1"冲程，3/4"HP泵系列（底部）F UHMWPE（超高分子聚乙烯密封）A2"冲程，1.5+2HP泵系列T增强聚四氟乙烯密封H2"冲程，1.5+2HP高压泵列V合成橡胶密封B底部进口Haskel气动体泵适用液体种类：1、石油，煤油，柴油，含5%可溶油的水2、淡水3、大多数的磷酸酯基液压油，与UHMWPE和合成橡胶相兼容的石油基溶剂4、石油基溶剂，氯化了的溶剂，甲基丙酮，乙醇，氟里昂等5、航空液压油，丙酮，乙醇等6、去离子水Haskel气动液本泵应用：★压力测试★螺栓紧固★千斤顶★夹具★制动系统★爆破试验★液压控制系统产品简介：美国Haskel气体增压泵由通过连接杆与小面积气体活塞直接相连的空气驱动往复式大面积活塞构成。
在每一个气体腔端盖中都包含输入、输出单向阀，空气驱动部分包含有循环轴和导向阀。
当通入驱动气体时，二者提供连续往复运动。
气体增压泵中气体压缩腔与空气驱动腔的分离是由三级动态密封装置提供的。
隔膜泵的操作说明
隔膜泵的操作说明一、引言隔膜泵是一种常用的工业泵，具有结构简单、使用方便、维护成本低等特点，在化工、食品、医药等领域被广泛应用。
本文将为您介绍隔膜泵的操作说明，以帮助您更加高效地使用和维护隔膜泵。
二、安全操作1. 在操作隔膜泵之前，务必穿戴好必要的个人防护设备，如安全手套、安全眼镜和防护服等。
2. 隔膜泵在运行时会产生振动和噪音，为了减少对操作人员的影响，请确保泵的安装牢固，以防止泵在运行过程中产生过多的振动和噪音。
3. 在操作隔膜泵之前，确保操作人员已经熟悉隔膜泵的结构和工作原理，并按照相关的操作手册进行操作。
4. 严禁将手、脚或其他物体伸入正在运行的隔膜泵中，以免发生意外。
三、启动与停止1. 启动隔膜泵前，确保供电电源已经连接正确，且泵的进出口管路已经连接好。
2. 打开泵的进、出口阀门，允许介质流入和流出隔膜泵。
3. 按下隔膜泵的启动按钮或开关，启动泵的电机。
在启动之前，确保泵的泵头已经充满液体，以免干转损坏泵。
4. 在使用过程中，如发现泵有异常声响或温度升高等异常情况，请及时停止使用，并检查故障原因。
四、调整流量1. 调整隔膜泵的流量，可通过调节进出口阀门的开度来实现。
打开进口阀门，可以增大流量；关闭进口阀门，则可减小流量。
2. 在调整流量时，请逐步调整，并观察泵的工作状态。
过大或过小的流量都可能导致泵的故障或效率降低。
五、维护保养1. 定期检查隔膜泵的使用条件，如泵体是否有异常磨损、阀门是否漏水等情况。
如有异常情况，请及时更换受损部件。
2. 检查隔膜泵的密封件，并及时更换损坏或老化的密封件，以确保泵的正常运行。
3. 定期清洗隔膜泵，并确保泵内无异物堵塞。
清洗时，可使用清水或适当的清洗剂，但请勿使用具有腐蚀性的溶剂。
4. 如果隔膜泵长时间不使用，应将泵体内的介质排空，并放置在干燥、通风的地方存放。
六、故障排除1. 如果隔膜泵出现漏水现象，首先检查阀门是否关闭不严密，如有需要可以更换密封圈。
可帕特拉公司 Husky 400 细菌消化剂漩涡洁净剂说明书
CANBERRA CORPORATIONSAFETY DATA SHEET1. IdentificationProduct Identifier: HUSKY 400 BACTERIAL DIGESTANT DEODORANTApplication or recommended use: Drain maintenance and deodorizerRestrictions on use: Do not use in any fashion not specified on the product label.Manufacturer / supplier: Canberra Corporation3610 N. Holland-Sylvania Rd.Toledo, Ohio 43615 USATelephone: 419-841-6616Emergency phone: 800-832-8992 National Poison Center: 800-222-12222. Hazards IdentificationGHS Classification: Classification of this mixture in accordance with paragraph (d) of §1910.1200.Eye Damage/Irritation - Category 2ALabel Elements:Symbol:Signal word: WARNINGHazard statements: Causes serious eye irritation.Precautionary statements: Wash hands, face and any skin contact thoroughly after handling.Wear eye protection/face protection.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if presentand easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.Other Hazards: None known3. Composition / Information on IngredientsChemical characterization: Mixture of water, detergents, bacterial spores and auxiliary agents.Hazardous ingredients: The exact percentage of composition has been withheld as a trade secret.1 - 1.4% Alcohol ethoxylate CAS 68439-46-3, EINECS/ELINCS NLP1 - 1.4% Sodium dodecylbenzene sulfonate CAS 25155-30-0, EINECS/ELINCS 246-680-4Other ingredients (> 1%):> 90% Water CAS 7732-18-5, EINECS/ELINCS 231-791-24. First-Aid MeasuresSymptoms: Irritation of affected areas. Causes serious eye irritation.Have the product container or label with you when calling a poison control center or doctor, or going for treatment. Inhalation: Move person to fresh air. If respiratory irritation or dizziness occurs, seek immediate medical assistance.Skin Contact: Remove contaminated clothing and wash before reuse. Wash contaminated area with soap and water for 15-20 minutes. If irritation occurs, get medical advice/attention.Eye Contact: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after first 5 minutes, then continue rinsing eye. Immediately call a POISON CENTER or doctor/physician.Ingestion: Call a poison control center or doctor immediately for treatment advice. Have person sip a glass of water if able to swallow. Do not induce vomiting unless told to do so by the poison control center or doctor. Do not give anything by mouth to a person who is unconscious or convulsing. If vomiting occurs, keep head below hips to reduce risk of aspiration.Note to Physician: Treat exposed patients symptomatically.5. Fire-Fighting MeasuresSuitable Extinguishing Media: Not applicable. Product is not a fire hazard.Unsuitable Extinguishing Media: High pressure water jet. Specific hazards in case of fire: None known.Special Fire Fighting Precautions: Fire fighters should wear appropriate protective equipment, including self-contained breathing apparatus and impervious clothing.6. Accidental Release MeasuresEmergency Procedures: Depending on the extent of release, consider the need for restriction of access to spill area. Personal Precautions: Do not eat, drink or smoke during clean up. Wear protective clothing, eye protection and impervious gloves (e.g. neoprene). Wash thoroughly after clean up.Environmental Precautions: Prevent spills from entering storm sewers/drains or contact with soil.6. Accidental Release Measures (cont.)Clean up Methods: Small spills may be wiped up and rinsed with water. For larger spills, contain spill with inert material (sand, clay). Transfer material to labeled containers for recovery or proper disposal. After removal, flush area with water. Follow good industrial hygiene practices.7. Handling and StoragePrecautions for Safe Handling: Read label before use. Avoid contact with skin or eyes. Wash hands, face and any skin contact thoroughly after handling. Do not eat, drink or smoke when using this product. Wear protective gloves, eye protection, face protection. Use product only according to label directions. If unsure about safe use, contact your supervisor. Conditions for Safe Storage: Keep out of reach of children. Do not contaminate water, food or feed by storage and disposal. Store in tightly closed, original container in a cool (10˚ - 30˚C), dry area.Incompatibility: None known.8. Exposure Controls / Personal ProtectionComponents with occupational exposure limits: NoneEngineering Controls: Proper ventilation in accordance with good industrial hygiene should be provided.Personal Protective EquipmentRespiratory: Respiratory protection is not necessary under normal conditions of use.Gloves: Recommended. Eye Protection: Chemical resistant goggles or face shield.Other: Protective clothing (long sleeves, pants), eyewash, safety shower are always advisable when working with chemicals.9. Physical and Chemical PropertiesPhysical State - Liquid Auto-ignition temperature - Not applicableColor - White Flash Point - NoneOdor - Balsam Flammability - Not applicableOdor Threshold - No data available Flammability Limits - Not applicableBoiling Point - 212°F Partition coefficient - Not applicableDecomposition temperature - No data available Solubility (Water) - CompleteFreezing Point - 32°F Vapor Density - No data availablepH (Neat) - 6.5 - 8.0 Vapor Pressure - No data availableRelative Density - 1.000 Viscosity - Water thinEvaporation Rate -Similar to water % VOC - < 1 (Excluding exempt material)10. Stability and ReactivityReactivity: No specific reactivity test data is available for this mixture. Under normal conditions of storage and use, hazardous reactions are not expected. Incompatible materials: Oxidizers.Chemical stability: This product is stable at ambient temperatures and pressures.Conditions to avoid: Temperatures above 50°C or below 10°C.Hazardous decomposition products: None known.11. Toxicological InformationAcute Toxicity: Toxicity data is not available for this mixture. Data below are estimates based on summation methods. Test Results Classification (A.0.4.1(c)) Basis (A.1.3.6.1)Oral > 2000mg/kg Not applicable Ingredient literature (Additive formula)Dermal > 2000mg/kg Not applicable Ingredient literature (Additive formula)Inhalation > 20 mg/L Not applicable Ingredient literature (Additive formula)Eye Damage/Irritation Irritation Category 2A Ingredient literatureSkin Damage/Irritation Not applicable Not applicable Ingredient literatureSummary: Skin and eye contact are most likely routes of exposure. Causes eye irritation.Subchronic/Chronic Toxicity:Test Results Classification BasisSkin Sensitization Not a sensitizer Not applicable Ingredient literature.Summary: Repeated or prolonged contact causes eye irritation.Carcinogens - Ingredients are not listed on the NTP Report on Carcinogens, IARC Monographs or by OSHAOther data - No other toxicological information is available for this mixture.12. Ecological InformationThis material has not been tested for acute environmental effects.Persistence and degradability: Material is not persistent. All organic components > 1% are readily biodegradable.Bio-accumulative potential: No evidence to suggest bio-accumulation will occur.Mobility: Accidental spillage may lead to penetration of soil and groundwater.13. Disposal ConsiderationsDo not contaminate water, food or feed by disposal. If these materials cannot be disposed of by use according to label directions, contact your State Environmental Control Agency, or the hazardous waste representative at the nearest EPA Regional Office for guidance. Rinse container promptly after emptying. Then offer for recycling or reconditioning, or puncture and dispose of in a sanitary landfill. If container is one gallon or less, wrap empty container in plastic bag and discard in trash.14. Transport InformationProper Shipping Name: Not regulated RQ - Not ApplicableShipping emergency phone: 800-424-9300Transport hazard class: Not Applicable Hazard Label: Not ApplicablePacking Group: Not Applicable Emergency Guide No.: Not Applicable Marine Pollutant: No15. Regulatory InformationInventory status: All components are listed on TSCA(US), EINECS/ELINCS(EU), DSL(Canada), AICS(Australia),ENCS(Japan).OSHA Hazard Communication Standard: This product meets the §1910.1200 definition of a "Hazardous Chemical". Superfund Amendments and Reauthorization Act of 1986 Title III (EPCRA) Sections 311 and 312Immediate (Acute) Health Hazard Yes Delayed (Chronic) Health Hazard NoFire Hazard No Reactive Hazard NoSudden Release of Pressure Hazard NoSuperfund Amendments and Reauthorization Act of 1986 Title III (EPCRA) Section 313*Chemicals marked with an asterisk in “3. Composition/Information on Ingredients” are subject to reporting requirements for Section 313 of Title III of the Superfund Amendments and Reauthorization Act (SARA) of 1986 and 40CFR Part 372. Pennsylvania/New Jersey/Massachusetts Right to KnowSee “3. Composition/Information on Ingredients” for hazardous and top five ingredients over 1% (w/w).California Proposition 65: This product does not contain a listed substance known to the State of California to cause cancer, birth defects or other reproductive harm, at levels which would require a warning under the statute.16. Other informationDate issued: 31. 12. 2014 F400-001 Revision: N/ADisclaimer: No representation or warranty, either expressed or implied, of merchantability, fitness for a particular purpose, or of any other nature, is made with respect to information concerning the product referred to in this document. The information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, it is impossible to foresee every health effect or exposure risk incurred by the use of this product. All chemicals present some degree of hazard and should be used with caution. The information and recommendations contained herein are presented in good faith. The user should review this information in conjunction with their knowledge of the application intended to determine the suitability of this product for such purpose. In no event will the supplier be responsible for any damages of any nature whatsoever, resulting from the use, reliance upon, or the misuse of this information. Furthermore, it is the direct responsibility of the user to comply with all applicable regulations governing the use and disposal of this material. Prepared by: R&D,Canberra Corporation。
HUSKY机培训资料
培训资料培训目的通过对原料及注塑成型的基本原理的初步介绍，使大家进一步熟悉原材料的基本特性和注塑成型的基本原理、设备的性能、安全生产以及最基本的参数的调整、对简单缺陷处理方法、以控制质量，使我们开阔思路增加一个互相学习的机会，从而使设备、质量、生产、工艺等各方面发展有一个扎实基础的保证。
一、原料（PET）的基础知识PET（聚酯）的全称是聚对苯二甲酸乙二醇酯，是一种中高分子量（25000~50000）长链型聚合物，其高分子（31000~50000）常被用来制造双向拉伸的瓶子即通常所讲的瓶用（PET）。
该树脂是一种圆柱形或平行六面体立方状态，体积为34~40mm3为一种半结晶态物体。
根据不同牌号的原料其玻璃化温度为75o C~80o C左右，其熔融温度在250o C，其加工温度在260o C~290o C之间。
此三个温度指标通常用于该PET的拉伸加热温度、塑化温度及机器、模具温度的设定参数。
PET为亲水性物质，其熔融状态时遇水分时将加速降解。
因此加工之前必须进行有效的干燥。
在挤出、注塑过程中，会有乙醛（AA）的放出，其残留量使加工困难。
我司采用的PET的特性粘度一般在0.76~0.90之间。
二、原料热成型的基本理论通常在自然界里我们把物质在常温下的聚集状态分为气态、液态、固态，高分子聚合物由于分子结构的连续性以及其巨大的分子量，所以它们的聚集状态不同与一般低分子化合物而在不同热力条件下以独特的三种形态存在，即玻璃态、高弹态和粘流态。
高分子聚合物的玻璃态实际上是固态的一种表现形式，特点是在一定的温度范围内呈现出固态物质普遍具有的性质，在某些力学特性上类似于普通的玻璃。
高分子聚合物的粘流态是一种独特的液态。
在某个高温范围内具有既可以流动又有别于普通低分子液体的力学特性。
高分子聚合物的高弹态是介于玻璃态和粘流态温度范围的独有形态。
因此，在我们瓶坯生产过程中可以这样描述：原料由原来的颗粒状经过温度、压力、剪切的作用下，从玻璃态经历了高弹态转变成粘流态压注到模腔里，并在模腔和坯筒内通过冷却再从粘流态经历了高弹态转变成玻璃态，得到我们所需的瓶坯。
格兰富spk样本
267 102
554
287
24 4x 7
109 64 G 3/4
100 115 130
注意！ 所有单位均为[mm] ，除非另有说明。 免责声明： 简化版尺寸图没有显示所有细节。
从格兰富CAPS打印出 [2016.04.035]
7/8
3HDH0308 SPK 2-8/8 50赫兹
公司名称: 制作人: 电话:
N/A 12.1 千克 13.4 千克
从格兰富CAPS打印出 [2016.04.035]
2/8
3HDH0308 SPK 2-8/8 50赫兹
H [米]
40
公司名称: 制作人: 电话:
日期:
2016/7/20
SPK 2-8/8, 3*400 V, 50Hz eta [%]
输送的液体 = 水 流体温度 = 20 °C 密度 = 998.2 kg/m
0.40
0.45
0.0 P2 [千瓦]
P1 [千瓦]
2800 2600
n 0.8
P1 0.6
2400
0.4
2200
0.2
2000 从格兰富CAPS打印出 [2016.04.035]
0.0 6/8
3HDH0308 SPK 2-8/8 50赫兹
141
公司名称: 制作人: 电话:
日期:
2016/7/20
80
35
70
30
60
25
50
20
40
15
30
10
20
5
10
0 0
P [千瓦]
0.4
0.3
0.2
0
5
10
15
气动隔膜泵样本
First choice whenForm No. 305-758Rev. B 2/98Husky ™3275Air-Operated Double Diaphragm Pumpquality counts.™The Husky 3275 is the biggest pump in Graco’s double diaphragm lineup. Its larger size enables it to deliver over 275 gallons (1041 liters) per minute.The lube-free Husky 3275 pump was engineered with the chemical,petrochemical, paper and mining industries in mind. It boasts the most reliable and trouble-free air switching valve in the world. The innovative design of the air switching valve prevents shut-down and air valve hang-up problems and can be serviced without disassembling the pump.The pump’s heavy-duty construction make it ideal for handling the most difficult chemical transfer, filter press feed, and dewatering applications.The most reliable and easy-to-service 3 in. (76 mm)pump on the market today!s Bolted leak-free flanged connections – no clamp bands used!s Large flow paths that can handle high viscositiess Easy air valve maintenance s Heavy-duty constructions Fluid flow up to 275 gpm (1040 lpm)Form No. 305-758Rev. B 2/98Technical SpecificationsMaximum fluid working pressure . . . . . . . . . . . . . . . . . . . . .120 psi (0.84 MPa, 8.4 bar)Air operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-120 psi (0.14-0.84 MPa, 1.4-8.4 bar)Maximum air consumption . . . . . . . . . . . . . . . . . . . . . . . . . . .325 scfm Air consumptionat 70 psi (480 kPa, 4.7 bar) / 100 gpm (379 lpm) . . . . . .120 scfm (1.26 m 3/min)Maximum free flow delivery . . . . . . . . . . . . . . . . . . . . . . . . .275 gpm (1,041 lpm)Maximum pump speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135 cpm Gallons (liters) per cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.0 (7.6)Maximum suction lift (water)Dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 ft. (2.4 m)Wet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 ft. (7.6 m)Maximum size pumpable solids . . . . . . . . . . . . . . . . . . . . . . .3/8 in. (9.4 mm)Air inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3/4 npt(f)Maximum operating temperature . . . . . . . . . . . . . . . . . . . . .150°F (65°C)Fluid inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 in. ANSI 4 bolt flange / DIN 8-bolt flange Fluid outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 in. ANSI 4 bolt flange / DIN 8-bolt flange Wetted partsAlumimum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .aluminum, T eflon, Santoprene, Hytrel, plated steel, acetal, SST WeightAlumimum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150 lbs. (68 kg)Instruction manualAlumimum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .308-639Performance Chart – Husky 32751142273414545686817959081022gpm lpmF L U I D P R E S S U R EFLUID FLOW(Pump tested in water with inlet submerged)140(9.8 0.98)120(8, 0.8)100(7, 0.7)80(5.5, 0.55)60(4.1, 0.41)40(2.8, 0.28)20(1.4, 0.14)0psi(bar, MPa)scfm (m 3/min)350(9.8)300(8.4)250(7.0)200(5.6)150(4.2)100(2.8)50(1.4)AIR CONSUMPTIONKey to Varying Air Pressures A at 120 psi (8 bar, 0.8 MPa)B at 100 psi (7 bar, 0.7 MPa)C at 70 psi (4.8 bar, 0.48 MPa)D at 40 psi (2.8 bar, 0.28 MPa)E at 20 psi (1.4 bar, 0.14 MPa)Form No. 305-758Rev. B 2/98Accessories110-197Quick-Connect (3/4) Air Supply Nipple Max. working pressure:300 psi (2.1 MPa, 21 bar).Inlet/outlet: 3/4 npt(f). Steel.110-200Quick-Connect (3/4) Air Supply Coupler Max. working pressure:300 psi (2.1 MPa, 21 bar).Inlet/outlet: 3/4 npt(f). Brass.107-141Air Shut-Off Valve BleedInlet/outlet: 3/4 npt(mxf). Bronze.224-040Air Guard Runaway ValveMax. working pressure:120 psi (0.83 MPa, 8.3 bar).Max. cfm @ 100 psi (0.7 MPa, 7 bar):250 scfm.Inlet/outlet: 3/4 npt(f). Aluminum alloy.238-881Integrated FR AssemblyMax. working pressure:120 psi (0.83 MPa, 8.3 bar).Inlet/outlet: 3/4 npt(f). Zinc.222-011Grounding Wire and ClampLength: 25 ft. (7.6 m). 12 ga. (1.5 mm 2).180-187High Volume Air RegulatorMax. working pressure:300 psi (2.1 MPa, 21 bar).Max. cfm @ 100 psi (0.7 MPa, 7 bar):380 scfm.Quick-disconnect: 1/4 in. gauge ports.Inlet/outlet: 3/4 npt(f).106-150Air FilterMax. working pressure:250 psi (1.72 MPa, 17.2 bar).Max. cfm @ 100 psi (0.7 MPa, 7 bar):260 scfm.Inlet/outlet: 3/4 npt(fbe). Zinc plated.Adapter Flange Kits Inlet/outlet: ANSI to npt.239-392Stainless steel 239-391Carbon steel 207-675Air Manifold 90°Inlet/outlet: 3/4 npt(f) x 3/4 npt(m).Quick-disconnect: 1/4 npt(f) and 1/8 npt(f) port.Carbon steel.238-765Air Valve Repair Kit3/4 npt(f)Air Exhaust(muffler not shown)FRONT VIEWSIDE VIEWDimension Drawings – Heavy-Duty Series© 1998, 1997 Graco Inc. Form No. 305-758 Rev. B 2/98 Printed in the U.S.A.GRACO INC.P .O. Box 1441Minneapolis, MN 55440-1441Sales/DistributionNorth America Toll Free 800-367-4023Telephone 612-623-6743Fax 612-623-6580Contact sales personnelLocate authorized distributors Product information literatureGraco Inc. is registered to I.S. EN ISO 9001.All written and visual data contained in this document are based on the latest productinformation available at the time of publication. Graco reserves the right to make changesat any time without notice.。
隔膜泵
例如：要选一台2寸的标准型聚丙烯泵，阀座为不锈钢，球及隔膜为特氟龙，则其编号应为DF2-311。
尺寸
1=1/4” (6.35 mm) Standard:polypropylene center section 2=1/4” (6.35 mm) Remote:polypropylene center section 3=3/8” (9.52 mm) Standard:aluminum center section 5=1/2” (12.7 mm) Standard:polypropylene center section 4=1/2” (12.7 mm) Remote:polypropylene center section 5=3/4” (19.05 mm) Standard:polypropylene center section 4=3/4” (19.05 mm) Remote:polypropylene center section B=1-1/2” (38.1 mm) Standard:aluminum center section C=1-1/2” (38.1 mm) Remote:aluminum center section T=1-1/2” (38.1 mm) Standard:stainless steel center section U=1-1/2” (38.1 mm) Remote:stainless steel center section F=2” (50.8 mm) Standard:aluminum center section G=2” (50.8 mm) Remote:aluminum center section V=2” (50.8 mm) Standard:stainless steel center section W=2” (50.8 mm) Remote:stainless steel center section K=3” (76.2 mm) Standard:aluminum center section
美国威尔顿气动隔膜泵规格型号(T1～T20)
• Turbo-Flo ™•T1 - 1/2" (12.7 mm) 金属泵 • T2 - 1" (25.4 mm) 金属泵• T4 - 1 1/2" (38.1 mm) 金属泵 • T8 - 2" (50.8 mm) 金属泵 • T15 - 3" (76.2 mm) 金属泵 • T20 - 4" (101.6 mm) 金属泵威尔顿 T1 - 1/2" (12.7 mm) 金属泵 技术参数口径：1/2"最大流量：14.5GPM (53.9LPM) 最大工作压力：125PSI (8.6BAR)接液部结构材质：铝合金、316不锈钢、镍基合金干吸：5' (1.6m)可通过最大颗粒：1/16" (1.6mm)弹性体：聚氨脂、丁晴橡胶、氟化橡胶、SaniFlex ™、特氟龙PTFE 、Wil-Flex ™各种材质的温度范围 聚丙烯0°C(32°F) ~ +79°C(+175°F) 碳充乙缩醛-28.9°C(-20°F) ~ + 65.6°C(+150°F) 聚偏二氟乙烯-12.2°C(-10°F) ~ + 107.2°C(+225°F) 特氟龙®PFA(½" UPII&UPIII)-28.9°C(-20°F) ~ + 148.9°C(+300°F) 特氟龙®PFA(½" & 1½")-28.9°C(-20°F) ~ + 107.2°C(+225°F)尺寸- T1 Array（金属泵）序号公制(mm) 英制(inch)A 28.6 1 1/8B 115.9 4 9/16C 198.5 7 13/16D 203.2 8E 207.2 8 5/32F 222.3 8 3/4G 174.6 6 7/8H 139.7 5 1/2 J 111.9 4 13/32 K 82.6 3 1/4 L 101.6 4M 30.2 1 3/16 N 30.2 1 3/16 P 7.1 9/32* 进出水口可供BSP英制螺纹口径：1"最大流量：35GPM (132.5LPM)最大工作压力：125PSI (8.6BAR)接液部结构材质：铝合金、316不锈钢、镍基合金干吸：17' (5.2m)可通过最大颗粒：1/8" (3.17mm)弹性体：聚氨脂、氯丁橡胶、丁晴橡胶、三元橡胶、氟化橡胶、SaniFlex™、特氟龙PTFE、Wil-Flex™各种材质的温度范围聚丙烯0°C(32°F) ~ +79°C(+175°F)碳充乙缩醛-28.9°C(-20°F) ~ + 65.6°C(+150°F)聚偏二氟乙烯-12.2°C(-10°F) ~ + 107.2°C(+225°F)特氟龙®PFA(½" UPII&UPIII)-28.9°C(-20°F) ~ + 148.9°C(+300°F)特氟龙®PFA(½" & 1½")-28.9°C(-20°F) ~ + 107.2°C(+225°F)尺寸- T2 Array（金属泵）序号公制(mm) 英制(inch)A 267.5 10 17/32B 36.5 1 7/16C 138.0 5 7/16D 254.0 10E 279.4 11F 28.6 1 1/8G 47.6 1 7/8H 95.3 3 3/4 J 77.0 3 1/32 K 184.2 7 1/4 L 209.6 8 1/4 M 171.5 6 3/4 N 106.4 4 3/16 P 127.0 5R 7.9 5/16S 51.6 2 1/32 T 31.8 1 1/4* 进出水口可供BSP英制螺纹威尔顿T4 - 1 1/2" (38.1 mm) 金属泵技术参数口径：1 1/2"最大流量：81GPM (306.6LPM)最大工作压力：125PSI (8.6BAR)接液部结构材质：铝合金、316不锈钢、铸铁、镍基合金干吸：18' (5.5m)可通过最大颗粒：3/16" (4.76mm)弹性体：聚氨脂、氯丁橡胶、丁晴橡胶、三元橡胶、氟化橡胶、SaniFlex™、特氟龙PTFE、Wil-Flex™各种材质的温度范围聚丙烯0°C(32°F) ~ +79°C(+175°F)碳充乙缩醛-28.9°C(-20°F) ~ + 65.6°C(+150°F)聚偏二氟乙烯-12.2°C(-10°F) ~ + 107.2°C(+225°F)特氟龙®PFA(½" UPII&UPIII)-28.9°C(-20°F) ~ + 148.9°C(+300°F)特氟龙®PFA(½" & 1½")-28.9°C(-20°F) ~ + 107.2°C(+225°F)尺寸- T4 Array（金属泵）序号公制(mm) 英制(inch)A 369.1 14 17/32B 62.7 2 15/32C 224.6 8 27/32D 428.6 16 7/8E 287.4 11 5/16F 261.9 10 5/16G 223.8 8 3/16H 152.4 6J 177.8 7K 50.8 2L 11.7 3 1/32 M 335.7 13 7/32 N 222.3 8 3/4 P 150.8 5 15/16 R 194.5 7 21/32 S 48.4 1 29/32 T 12.7 1/2* 进出水口可供BSP英制螺纹口径：2"最大流量：163GPM (617.0LPM)最大工作压力：125PSI (8.6BAR)接液部结构材质：铝合金、316不锈钢、铸铁、镍基合金干吸：21' (6.4m)可通过最大颗粒：1/4" (6.35mm)弹性体：聚氨脂、氯丁橡胶、丁晴橡胶、三元橡胶、氟化橡胶、SaniFlex™、特氟龙PTFE、Wil-Flex™各种材质的温度范围聚丙烯0°C(32°F) ~ +79°C(+175°F)碳充乙缩醛-28.9°C(-20°F) ~ + 65.6°C(+150°F)聚偏二氟乙烯-12.2°C(-10°F) ~ + 107.2°C(+225°F)特氟龙®PFA(½" UPII&UPIII)-28.9°C(-20°F) ~ + 148.9°C(+300°F)特氟龙®PFA(½" & 1½")-28.9°C(-20°F) ~ + 107.2°C(+225°F)尺寸- T8 Array（金属泵）序号公制(mm) 英制(inch)A 404.0 15 29/32B 47.6 1 7/8C 628.7 24 3/4D 669.2 26 11/32E 372.3 14 21/32F 57.2 2 1/4G 61.7 2 7/16H 270.7 10 21/32 J 342.9 13 1/2 K 229.4 9 1/32 L 254.0 10M 255.6 10 1/16 N 313.5 12 11/32 P 14.3 9/16R 63.5 2 1/2 S 51.6 2 1/32 T 281.8 11 3/32 U 101.6 4V 280.2 11 1/32 W 386.6 15 7/32 X Ø14.3 Ø9/16* 进出水口可供BSP英制螺纹口径：3"最大流量：232GPM (878.1LPM)最大工作压力：125PSI (8.6BAR)接液部结构材质：铝合金、316不锈钢、铸铁、镍基合金干吸：19' (5.8m)可通过最大颗粒：3/8" (9.5mm)弹性体：聚氨脂、氯丁橡胶、丁晴橡胶、三元橡胶、氟化橡胶、SaniFlex™、特氟龙PTFE、Wil-Flex™各种材质的温度范围聚丙烯0°C(32°F) ~ +79°C(+175°F)碳充乙缩醛-28.9°C(-20°F) ~ + 65.6°C(+150°F)聚偏二氟乙烯-12.2°C(-10°F) ~ + 107.2°C(+225°F)特氟龙®PFA(½" UPII&UPIII)-28.9°C(-20°F) ~ + 148.9°C(+300°F)特氟龙®PFA(½" & 1½")-28.9°C(-20°F) ~ + 107.2°C(+225°F)尺寸- T15 Array（金属泵）序号公制(mm) 英制(inch)A 505.2 19 29/32B 59.5 2 11/32C 760.6 29 31/32D 821.7 32 3/8E 419.1 16 1/2F 71.4 2 13/16G 82.6 3 1/4H 312.5 12 5/16 J 425.5 16 3/4 K 360.4 14 3/16 L 304.8 12M 257.8 10 5/32 N 281.8 11 3/32 P 15.9 5/8R 69.9 2 3/4 S 65.8 2 19/32 T 305.4 12 1/32 U 42.9 1 11/16 V 305.4 12 1/32 W 475.9 18 3/4 X Ø15.9 Ø5/8* 进出水口可供BSP英制螺纹威尔顿T20 - 4" (101.6 mm) 金属泵技术参数口径：4"最大流量：275GPM (1040.0LPM)最大工作压力：125PSI (8.6BAR)接液部结构材质：铸铁干吸：12' (3.7m)可通过最大颗粒：1 3/8" (35mm)弹性体：聚氨脂、三元橡胶、氟化橡胶、SaniFlex™、特氟龙PTFE、Wil-Flex™各种材质的温度范围聚丙烯0°C(32°F) ~ +79°C(+175°F)碳充乙缩醛-28.9°C(-20°F) ~ + 65.6°C(+150°F)聚偏二氟乙烯-12.2°C(-10°F) ~ + 107.2°C(+225°F)特氟龙®PFA(½" UPII&UPIII)-28.9°C(-20°F) ~ + 148.9°C(+300°F)特氟龙®PFA(½" & 1½")-28.9°C(-20°F) ~ + 107.2°C(+225°F)威尔顿T20 - 4" (101.6 mm) 金属泵结构图尺寸- T20 Array（金属泵）序号公制(mm) 英制(inch)A 943 37.13B 825 32.50C 552 21.75D 438 17.25E 330 13F 118 4.63G 156 6.13H 158 6.25J 210 8.25K 229 9L 102 4M 190 7.5N 19 0.75P 454 17.88 R 375 14.75 S 330 13T 279 11U 14 0.56。
Husky1050油水提升泵说明书
固瑞克公司的质保条款. . . . . .
. . 32
有关固瑞克公司的资料. . . . . . . . . . . . . . . . . . . . . . . . . 32
相关手册
手册 312877 313597 313598 313840 406824 406825 406826
描述 Husky1050气动隔膜泵、操作 Husky UL-Listed1050A隔膜泵、操作 Husky 1050A CSA认证隔膜泵、操作 DataTrak指示/零件, 脉冲计数包、指令 磁簧开关与电磁包、指令 转矩指令(流形与流体覆盖)
剂制造商的警告。 z 要求MSDS从批发或零售商中获得关于资料的完整信息。 z 在设备被通电或压力时不要离开工作区域。在设备不使用时候，关闭所有的设备和遵循减压
程序手册。 z 日常检查设备。立即修理或更换磨损或损坏的部件，只能用真正制造商的更换部件。 z 不要变更或修改设备。 z 只使用设备为其预期的目的。打电话给你的经销商要求更多的信息。 z 软管和电缆远离交通区域,锋利边缘,运动部件,以及热的表面。 z 不要纠结或弯曲软管或用软管拉设备。 z •使孩子和动物离开工作区域。 z •符合所有适用的安全条例。
DataTrak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
止回阀检修. . . . . . . . . . . . . . . . . . . . . . 11
隔膜中心部分 . . . . . . . . . . . . 12
拆卸和清洁的空气阀，见到 第 9 页。 替换阀球和底座，见第 11 页。 替换导向阀，见第 12 页。
替换垫圈，见第 8 页。 安装减压组件。见附件, 第 29 页 泄压压力和清理阀门 清洁空气管 检查；清洁
米 顿 罗 米 顿 罗 - HASKEL增压泵 HIP高压阀门 气密封试验
C
6 级变频电机，B3,3Ph-50Hz-380V
D
6 级电机，B3,3Ph-50Hz-380V
E
8 级变频电机，B3,3Ph-50Hz-380V
F
8 级电机，B3,3Ph-50Hz-380V
X
其它
工作压力
代号 注明实际工况操作压力（bar）
流量调节
N
不可调节（标准）
A
50%-100% 流量调节
注 : 选项 A 适用于低压结构 ( ＜ 200bar)
填料结构
U
VEE 型填料 ( 标准 )
X
特殊要求填料
填料润滑
N
无润滑（标准）
A
润滑脂滑润
B
连续润滑脂滑润
C
滴油润滑
X
特殊要求
Poweroyal Triplex A 系列高压往复泵
045 45.45
050 50.80
055 57.15
电机功率
A B C D E F
060 63.50
5.5kW 7.5kW 11kW 15kW 18.5kW 22 kW
1815
1885/1935
B
773
815
835
880
885
915
950
C
1350
1500
1600
1700
1750
1800
1800
P ≥ 200bar
P>200bar
北京海德利森科技有限公司
中国 北京 西二环 100054 菜户营58号财富西环大厦2515室 电话：86 10 63357350 传真：86 10 63356406 邮箱：sales@
气动隔膜泵操作说明书
VERSA-MATIC®气动隔膜泵操作指南●安装注意事项●操作说明●零备件清单代理商: 北京休思机械设备有限公司北京西城区月坛北小街13号电话:+86 10 68053613邮编:100037 传真:+86 10 68018103本中文稿仅供使用者参考，如有理解歧义，请以英文原稿为准。
VERSA-MATIC®气动隔膜操作说明一、VERSA-MATIC®专利气阀系统VERSA-MA TIC®气阀系统是世界上唯一的专利气阀。
气阀系统由气阀、导向轴组成。
他是靠压力差和自身具有的永久磁性来驱动气阀。
压缩空气由气阀分配给左右气室，推动隔膜运动，隔膜运动的同时，隔膜内压板推动导向轴运动，导向轴可以将部分用过的一次气再次分配给气阀，推动气阀运动。
专利气阀系统的优势在于他是磁性气阀，没有死点，没有冰点，可以在低温下运行。
由于压缩空气的再次利用，与非专利气阀系统比较，专利气阀系统可以省气30%。
二、一般安全说明1、设备的输出压力等于供给的压缩空气的压力，所以不要超过推荐的使用压力。
金属材质泵供给压力不要超过9bar，塑料材质的供给压力不要超过7bar。
2、如果您输送的是危险介质，请您穿好防护服，戴好防护镜。
3、在启动前，应对压缩空气系统进行吹扫，确保压缩空气的洁净；并确认开关阀，压力调节器，压力泄放阀和其他仪表工作正常。
4、在进行维护和修理之前，必须关闭压缩空气，拆离供气管线。
并保证泵内的压力已被完全泄放掉。
5、在运转时，身体的任何部位不要接近泵的排气口。
6、不要使用有泄露的，有故障的，或已被腐蚀的泵，这样的泵不能保证获得足够的压力。
7、气动隔膜泵在设计上为使用压缩空气为动力源，其他的压缩气体没有被检测过，使用时可能会有不安全因素。
8、不要输送与泵不适合的介质，那样将造成严重的后果；如果不能确认介质是否与泵适合，请与您的经销商联系。
9、确保泵体和弹性体部件在规定的温度范围内工作。
Husky
操作Husky ®1050 气动膜隔泵配有模块化空气阀的 1 英寸泵，适用于流体输送应用。
仅适合专业用途。
有关型号资料和核准情况请参见第 4 页。
125 磅/平方英寸 (0.86 兆帕, 8.6 巴) 最大流体工作压力125 磅/平方英寸 (0.86 兆帕, 8.6 巴) 最大空气入口压力ti13844a端法兰1050P 聚丙烯1050C 导电聚丙烯1050FPVDF1050S 不锈钢1050H 哈氏合金ti14342a 1050A 铝质ti13946a 3A0549ZAGZH相关手册23A0549ZAG目录相关手册 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2查找离您最近的经销商 . . . . . . . . . . . . . . . . . . . . . . . 3指定新泵的配置 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3订购更换部件 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3经销商注释 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3泵表格 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4证书 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5警告 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6安装 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9设置前拧紧紧固件 . . . . . . . . . . . . . . . . . . . . . . . . 9减少气蚀秘诀 . . . . . . . . . . . . . . . . . . . . . . . . . . . 9安装 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10接地 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10空气管路 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11舌簧开关 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11排气通风 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12流体供应管路 . . . . . . . . . . . . . . . . . . . . . . . . . . 13流体出口管路 . . . . . . . . . . . . . . . . . . . . . . . . . . 13流体入口和出口接口 . . . . . . . . . . . . . . . . . . . . . 15流体泄压阀 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16操作 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17泄压流程 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17首次使用泵之前要对其进行冲洗 . . . . . . . . . . . . 17设置前拧紧紧固件 . . . . . . . . . . . . . . . . . . . . . . . 17启动和调节泵 . . . . . . . . . . . . . . . . . . . . . . . . . . 17DataTrak 操作 . . . . . . . . . . . . . . . . . . . . . . . . . . 18关闭泵 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18维护 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18维护计划 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18润滑 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18拧紧螺纹连接处 . . . . . . . . . . . . . . . . . . . . . . . . . 18冲洗和存放 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18扭矩说明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19尺寸和安装 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20铝质 (1050A) . . . . . . . . . . . . . . . . . . . . . . . . . . . 20聚丙烯 (1050P)、导电聚丙烯 (1050C) 和 PVDF(1050F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21哈氏合金 (1050H) 和不锈钢 (1050S) . . . . . . . . 22具有中心法兰歧管的不锈钢 (1050S) . . . . . . . . . 23不锈钢，中心三夹 (1050S) . . . . . . . . . . . . . . . . 24性能表 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25技术数据 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Graco Husky 泵标准担保 . . . . . . . . . . . . . . . . . . . . . 28Graco 信息 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28相关手册手册描述313435Husky 1050 气动隔膜泵，修理/零部件313597Husky 1050A UL 认证的隔膜泵，操作313598Husky 1050A CSA 认证的隔膜泵，操作313840DataTrak，零部件说明书406824脉冲计数配件包，说明书查找离您最近的经销商查找离您最近的经销商1.请访问 .2.单击“购买地点”并使用“经销商定位器”。
Husky 2150气动双隔膜泵
铝泵样品
装
流体卸压阀
警惕
一些系统要求在泵浦出口管处安装一个卸压阀， 以防止系统过压，而造成泵浦或软管的破裂，见 图 4。
流体在出口管的热膨胀可引起过压。这种情况一 般出现在使用较长的，暴露于阳光下或室温环境 下的流体管，或把流体从较冷区域抽吸至较热区 域时（如地下罐中流体抽吸）。
如果使用 Husky 泵浦向活塞泵供应流体，且活 塞泵的进给阀没有关闭，导致流体回流至 Husky 泵浦出口管，也可导致过压。
安
装
概述
1. 图 2 所示典型安装仅作为选择和安装系统部件的 一般指导。您所需特定设备的选择与安装，请联系 固瑞克分销商或固瑞克技术服务部门以获取技术 帮助。
2. 确保只使用正牌的固瑞克部件和附件。
3. 括号中的指示数字和字母代表第 22、23 页上的图 和零件清单中的 call out。
警告
危险流体 为减少严重人身伤害，流体溅入眼睛或 皮肤，有毒流体溅入等的危险，请不要 在泵浦中有压力时移动或提升它。否则， 一旦泵浦落下，泵浦流体部分将会崩裂。确保在移动 和提升泵浦之前，遵照第 9 页的卸压程序警告进行操 作。
支架橡皮撑脚 236-452 可以减少操作过程中的噪音和 振动。
空气管路
警告
泵浦设备中应配有一个漏式主空气阀（B），用以排 除积聚在此阀和泵浦之间的空气。积聚的空气可引起 泵浦空打，从而可能导致严重人身伤害，如流体溅入 眼睛，皮肤等，移动部件碰伤，或危险流体污染等。 见图 2
1. 如图 2 所示安装空气管附件。把这些附件固定在墙 壁上或支架上。确保空气管上的附件都已正确接 地。 a. 安装一个空气调压器（C）和气压表，用以控 制流体压力。流体出口压力应与空气调压器设 置压力一致。
隔膜泵培训
Frank Ren, Graco CQ 2001
GRACO主要产品
汽车工业喷涂设备
一般工业喷涂设备
建筑业喷涂设备
润滑设备
流体输送设备
Frank Ren, Graco CQ 2001
流体输送设备：
HUSKY 气动双隔膜泵 PISTON气动输送泵
Frank Ren, Graco CQ 2001
Frank Ren, Graco CQ 2001
竞争对手回顾—性能比
特点
优势 无停机问题 流量大于Wilden, Yamada和其他公司 对于1/4”，3/8”，1/2”，3/4”泵，选择多样 具有更大的流量,更佳的性能 免润滑，无结冰滑阀空气马达 Teflon隔膜，满负荷输送 1/4“，3/8“，1/2”和3/4“多种型号选择 HUSKY1”，1.5”&2”泵使用相同空气阀
Frank Ren, Graco CQ 2001
HUSKY 产品系列
产品系列 HUSKY 205，307，308，515，716 HUSKY 1040，1590，2150，3275 工作原理 GRACO技术优势
Frank Ren, Graco CQ 2001
HUSKY205 简介
GRACO 液体腔特点
塑料泵体材质采用 纯 聚丙烯，导电乙缩醛 金属泵体材质采用 阳极氧化AL，316 SST ，铸铁 进出口位于泵两侧 提高安装的挠度 防止液体渗入空气腔 减少压损，流量更大 AL 电镀后提高抗腐蚀能力 SST 316 钝化处理 螺栓连接 夹箍连接
典型竞争对手
进出口位于泵中央（WILDEN，ARO）
GRACO公司流体输送泵
huskyhy手册4
第9章维护本章包括一份维护计划以及所有预防性和校正性维护任务的步骤。
维护计划表9-1列出了每日、每周、每月、每季、每半年以及每年的维护计划。
表9-1 维护计划– Hylectric注塑机。
项目频率任务说明参考页2每天清洁注口、定模板和清料安全门7-44页3每天检查机器安全设备7-5页4每天清洁机器和HMI9-4页9-4页5每周检查储能器预充压（注：在储能器充压后第一周结束时进行此项检查）6每周检查液压油箱中油的质量（注：在加注油箱后第一周9-25页结束时进行此项检查）7每周检查滤油器9-12页8每周检查并清洁磁力吸头9-14页9每周检查并清洁料斗、选装的料斗磁铁9-14页10每周检查油回收器9-16页11每月检查电器元件9-17页12每月检查所有液压油缸、阀及分流板9-17页13每月检查所有液压软管组件和接头9-18页14每月检查系统压力9-21页15每月检查所有冷却水元件9-22页16每月检查所有气动阀和软管9-22页表9-1 维护计划– Hylectric注塑机。
项目频率任务说明参考页18每月润滑锁板油缸活塞杆端部9-24页19每季度检查储能器预充压9-4页20每季度检查液压油箱中油的质量9-25页21每季度检查液压油箱油位9-27页22每季度检查齿轮箱油位9-31页23每季度检查电动马达9-34页24每季度润滑模具行程导柱衬套9-34页25每季度检查选装的注口分配阀衬套和插销9-36页26每六个月润滑线性轴承–动模板（H/HL225-H/HL500）9-37页27每六个月润滑线性轴承–选装的叠模托架9-39页28每六个月润滑线性轴承–注塑活塞9-40页29每六个月更换滤油器滤芯9-41页30每六个月检查注射座油缸衬套和插销9-44页31每年调节机器水平度和注口同心度9-45页32每年更换通风孔盖过滤器滤芯9-57页33每年更换空气过滤器滤芯9-58页34每年润滑泵马达轴承9-59页35每年更换齿轮箱油9-31页36每年更换ITT节水阀薄膜9-62页37根据需要更换液压油9-28页38根据需要检查安全装置（注：软件升级或者对联锁件进行维9-63页修后需要执行此项检查）表9-1 维护计划– Hylectric注塑机。
可布拉公司HUSKY 401磷酸酯消除器说明书
CANBERRA CORPORATIONSAFETY DATA SHEET1. IdentificationProduct Identifier: HUSKY 401 URIC ACID ERADICATORApplication or recommended use: Bacterial cleaner and deodorizerRestrictions on use: Do not use in any fashion not specified on the product label.Manufacturer / supplier: Canberra Corporation3610 N. Holland-Sylvania Rd.Toledo, Ohio 43615 USATelephone: 419-841-6616Emergency phone: 800-832-8992 National Poison Center: 800-222-12222. Hazards IdentificationGHS Classification: Classification of this mixture in accordance with paragraph (d) of §1910.1200.Eye Damage/Irritation - Category 2ALabel Elements:Symbol:Signal word: WARNINGHazard statements: Causes serious eye irritation.Precautionary statements: Wash hands, face and any skin contact thoroughly after handling.Wear eye protection/face protection.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if presentand easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.Other Hazards: None known3. Composition / Information on IngredientsChemical characterization: Mixture of water, detergents, bacterial spores and auxiliary agents.Hazardous ingredients: The exact percentage of composition has been withheld as a trade secret.1 - 1.4% Alcohol ethoxylate CAS 68439-46-3, EINECS/ELINCS NLP1 - 1.4% Sodium dodecylbenzene sulfonate CAS 25155-30-0, EINECS/ELINCS 246-680-4Other ingredients (> 1%):> 90% Water CAS 7732-18-5, EINECS/ELINCS 231-791-24. First-Aid MeasuresSymptoms: Irritation of affected areas. Causes serious eye irritation.Have the product container or label with you when calling a poison control center or doctor, or going for treatment. Inhalation: Move person to fresh air. If respiratory irritation or dizziness occurs, seek immediate medical assistance.Skin Contact: Remove contaminated clothing and wash before reuse. Wash contaminated area with soap and water for 15-20 minutes. If irritation occurs, get medical advice/attention.Eye Contact: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after first 5 minutes, then continue rinsing eye. Immediately call a POISON CENTER or doctor/physician.Ingestion: Call a poison control center or doctor immediately for treatment advice. Have person sip a glass of water if able to swallow. Do not induce vomiting unless told to do so by the poison control center or doctor. Do not give anything by mouth to a person who is unconscious or convulsing. If vomiting occurs, keep head below hips to reduce risk of aspiration.Note to Physician: Treat exposed patients symptomatically.5. Fire-Fighting MeasuresSuitable Extinguishing Media: Not applicable. Product is not a fire hazard.Unsuitable Extinguishing Media: High pressure water jet. Specific hazards in case of fire: None known.Special Fire Fighting Precautions: Prevent human exposure to fire, smoke, fumes or products of combustion. Fire fighters should wear appropriate protective equipment, including self-contained breathing apparatus and impervious clothing.6. Accidental Release MeasuresEmergency Procedures: Depending on the extent of release, consider the need for restriction of access to spill area. Personal Precautions: Do not eat, drink or smoke during clean up. Wear protective clothing, eye protection and impervious gloves (e.g. neoprene). Wash thoroughly after clean up.Environmental Precautions: Prevent spills from entering storm sewers/drains or contact with soil.6. Accidental Release Measures (cont.)Clean up Methods: Small spills may be wiped up and rinsed with water. For larger spills, contain spill with inert material (sand, clay). Transfer material to labeled containers for recovery or proper disposal. After removal, flush area with water. Follow good industrial hygiene practices.7. Handling and StoragePrecautions for Safe Handling: Read label before use. Avoid contact with skin or eyes. Wash hands, face and any skin contact thoroughly after handling. Do not eat, drink or smoke when using this product. Wear protective gloves, eye protection, face protection. Use product only according to label directions. If unsure about safe use, contact your supervisor. Conditions for Safe Storage: Keep out of reach of children. Do not contaminate water, food or feed by storage and disposal. Store in tightly closed, original container in a cool (10˚ - 30˚C), dry area.Incompatibility: None known.8. Exposure Controls / Personal ProtectionComponents with occupational exposure limits: NoneEngineering Controls: Proper ventilation in accordance with good industrial hygiene should be provided.Personal Protective EquipmentRespiratory: Respiratory protection is not necessary under normal conditions of use.Gloves: Recommended. Eye Protection: Chemical resistant goggles or face shield.Other: Protective clothing (long sleeves, pants), eyewash, safety shower are always advisable when working with chemicals.9. Physical and Chemical PropertiesPhysical State - Liquid Auto-ignition temperature - Not applicableColor - Light purple Flash Point - NoneOdor - Vanilla Flammability - Not applicableOdor Threshold - No data available Flammability Limits - Not applicableBoiling Point - 212°F Partition coefficient - Not applicableDecomposition temperature - No data available Solubility (Water) - CompleteFreezing Point - 32°F Vapor Density - No data availablepH (Neat) - 6.5 - 8.0 Vapor Pressure - No data availableRelative Density - 1.000 Viscosity - Water thinEvaporation Rate -Similar to water % VOC - < 1 (Excluding exempt material)10. Stability and ReactivityReactivity: No specific reactivity test data is available for this mixture. Under normal conditions of storage and use, hazardous reactions are not expected. Incompatible materials: Oxidizers.Chemical stability: This product is stable at ambient temperatures and pressures.Conditions to avoid: Temperatures above 50°C or below 10°C.Hazardous decomposition products: None known.11. Toxicological InformationAcute Toxicity: Toxicity data is not available for this mixture. Data below are estimates based on summation methods. Test Results Classification (A.0.4.1(c)) Basis (A.1.3.6.1)Oral > 2000mg/kg Not applicable Ingredient literature (Additive formula)Dermal > 2000mg/kg Not applicable Ingredient literature (Additive formula)Inhalation > 20 mg/L Not applicable Ingredient literature (Additive formula)Eye Damage/Irritation Irritation Category 2A Ingredient literatureSkin Damage/Irritation Not applicable Not applicable Ingredient literatureSummary: Skin and eye contact are most likely routes of exposure. Causes serious eye irritation.Subchronic/Chronic Toxicity:Test Results Classification BasisSkin Sensitization Not a sensitizer Not applicable Ingredient literature.Summary: Repeated or prolonged contact causes serious eye irritation.Carcinogens - Ingredients are not listed on the NTP Report on Carcinogens, IARC Monographs or by OSHAOther data - No other toxicological information is available for this mixture.12. Ecological InformationThis material has not been tested for acute environmental effects.Persistence and degradability: Material is not persistent. All organic components > 1% are readily biodegradable.Bio-accumulative potential: No evidence to suggest bio-accumulation will occur.Mobility: Accidental spillage may lead to penetration of soil and groundwater.13. Disposal ConsiderationsDo not contaminate water, food or feed by disposal. If these materials cannot be disposed of by use according to label directions, contact your State Environmental Control Agency, or the hazardous waste representative at the nearest EPA Regional Office for guidance. Rinse container promptly after emptying. Then offer for recycling or reconditioning, or puncture and dispose of in a sanitary landfill. If container is one gallon or less, wrap empty container in plastic bag and discard in trash.14. Transport InformationProper Shipping Name: Not regulated RQ - Not ApplicableShipping emergency phone: 800-424-9300Transport hazard class: Not Applicable Hazard Label: Not ApplicablePacking Group: Not Applicable Emergency Guide No.: Not Applicable Marine Pollutant: No15. Regulatory InformationInventory status: All components are listed on TSCA(US), EINECS/ELINCS(EU), DSL(Canada), AICS(Australia),ENCS(Japan).OSHA Hazard Communication Standard: This product meets the §1910.1200 definition of a "Hazardous Chemical". Superfund Amendments and Reauthorization Act of 1986 Title III (EPCRA) Sections 311 and 312Immediate (Acute) Health Hazard Yes Delayed (Chronic) Health Hazard NoFire Hazard No Reactive Hazard NoSudden Release of Pressure Hazard NoSuperfund Amendments and Reauthorization Act of 1986 Title III (EPCRA) Section 313*Chemicals marked with an asterisk in “3. Composition/Information on Ingredients” are subject to reporting requirements for Section 313 of Title III of the Superfund Amendments and Reauthorization Act (SARA) of 1986 and 40CFR Part 372. Pennsylvania/New Jersey/Massachusetts Right to KnowSee “3. Composition/Information on Ingredients” for hazardous and top five ingredients over 1% (w/w).California Proposition 65: This product does not contain a listed substance known to the State of California to cause cancer, birth defects or other reproductive harm, at levels which would require a warning under the statute.16. Other informationDate issued: 31. 12. 2014 F401-001 Revision: N/ADisclaimer: No representation or warranty, either expressed or implied, of merchantability, fitness for a particular purpose, or of any other nature, is made with respect to information concerning the product referred to in this document. The information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, it is impossible to foresee every health effect or exposure risk incurred by the use of this product. All chemicals present some degree of hazard and should be used with caution. The information and recommendations contained herein are presented in good faith. The user should review this information in conjunction with their knowledge of the application intended to determine the suitability of this product for such purpose. In no event will the supplier be responsible for any damages of any nature whatsoever, resulting from the use, reliance upon, or the misuse of this information. Furthermore, it is the direct responsibility of the user to comply with all applicable regulations governing the use and disposal of this material. Prepared by: R&D,Canberra Corporation。