BDS14SMD05中文资料
士兰微电子 SD05M50DBE DBS 说明书
智能功率模块(IPM)，500V/5A 三相全桥驱动描述SD05M50DBE/DBS 是高度集成、高可靠性的三相无刷直流电机驱动电路，主要应用于风扇类的小功率电机驱动。
其内置了6个快恢复功率MOS 管和3个半桥高压栅极驱动电路。
SD05M50DBE/DBS 内部集成了欠压保护功能，提供了优异的保护和失效保护操作。
由于每一相都有一个独立的负直流端，其电流可以分别单独检测。
SD05M50DBE/DBS 采用了高绝缘、易导热和低电磁干扰的设计，提供了非常紧凑的封装体，使用非常方便，尤其适合内置于电机的应用和要求紧凑安装的场合。
主要特点♦ 内置6个500V/5A 的快恢复功率MOS 管 ♦ 内置高压栅极驱动电路(HVIC) ♦ 内置欠压保护♦ 内置自举二极管完全兼容3.3V 和5V 的MCU 的接口，高电平有效♦ 3个独立的负直流端用于变频器电流检测的应用 ♦优化并采用了低电磁干扰设计 ♦绝缘级别1500V rms /min应用♦ 室内/户外空调 ♦ 冰箱压缩机 ♦ 排气扇 ♦ 风扇 ♦ 空气净化器 ♦洗碗机水泵产品规格分类产品名称封装形式 打印名称 环保等级 包装 SD05M50DBE DIP-23E SD05M50DBE 无铅 料管 SD05M50DBSSOP-23HSD05M50DBS无铅料管内部框图极限参数参 数 符号 参 数 范 围 单位 加在P-N之间的电源电压V PN500 V单个功率MOS的漏极持续电流，I D25 3.0 A T C=25°C单个功率MOS的漏极持续电流，I D80 2.0 A T C=80°C单个功率MOS的漏极峰值电流I DP 5.0 A T C=25°C, 脉冲宽度<100μs最大功率耗散，T C=25°C P D14.7 W 控制电源电压V CC20 V 高侧控制电压V BS20 V 输入信号电压V IN-0.3~V CC+0.3 V 工作结温范围T J-40~150 °C 工作壳温范围, T J≤150°C（备注1）T C-40~125 °C 存储温度范围T STG-40~125 °C 结壳热阻RθJC8.5 °C/W绝缘电压，60Hz，正弦，交流1分钟，V ISO1500 V rms 引脚与散热片之间自举二极管正向电流，T C=25°C I F0.5 A自举二极管正向电流峰值，T C=25°C，I FP 1.5 A 脉宽1ms备注1：壳温测试点，请看图3所示。
SD Series 防静电设备说明书
T h e S D S e r i e s is a range of surge protection devices combining unparalleled packing densities, application versatility, proven reliable hybrid circuitry, simple installation and optional ‘loop disconnect’facilities – features which make the series the ultimate surge protection solution for process equipment, I/O systems and communications networks.T h e e x c e p t i o n a l l y h i g h p a c k i n g d e n s i t i e s are the consequence of an ultra slim ‘footprint’ for individual modules which can thus ‘double-up’ as feedback terminals. Each module provides full hybrid surge protection for 2 and 3 wire loop protection.M o d u l e s w i t h a c o m p r e h e n s i v e r a n g e o f v o l t a g e r a t i n g s cover all process related signals such as RTDs, THCs, 4 to 20mA loops, telemetry outstations, shut-down systems and fire and gas detectors.O p t i o n a l‘l o o p d i s c o n n e c t’,is a feature which allows commissioning and maintenance to be carried out without removal of the surge protection device.This facility is provided by the SD07, SD16,SD32 and SD55 units. In addition, a thirdconnection on the field and safe side ofthe protector is provided in order toterminate screens safely.F o r t h r e e w i r e a p p l i c a t i o n s the speciallydesigned SD RTD(ResistanceTemperature Detector) and the SD32T3,(for separately powered 4-20mA loops)provide full 3-wire protection in a singlecompact unit. The recommended choicefor the protection of 3-wire pressuretransducers on low power circuits is theSD07R3.F o r h i g h e r b a n d w i d t h a p p l i c a t i o n s,theSDR series has been developed to meetthe demands of today’s highest speedcommunication systems.120V a n d240V A C v e r s i o n sare available for I/O andpower supplies up tothree Amps of loadcurrent.T e l e p h o n e n e t w o r k s can be protected bythe SDPSTN.O n e s i m p l e m a n u a l o p e r a t i o n clampsmodules securely onto DIN rail, whichautomatically provides the essential high-integrity earth connection.‘T o p-h a t’(T-s e c t i o n)D I N r a i l is generallysuitable for mounting SD modulesalthough for adverse environments, aspecially-plated version is available fromMTL Surge Technologies. Acomprehensive range of mounting andearthing accessories can also besupplied, see page 7 for furtherdetails.G U l t r a-s l i m s p a c e-s a v i n g d e s i g n;e a s y i n s t a l l a t i o n G M u l t i s t a g e h y b r i d p r o t e c t i o n c i r c u i t r y–10k Am a x i m u m s u r g e c u r r e n tG R a n g e o f v o l t a g e r a t i n g s--t o s u i t a l l p r o c e s s I/Oa p p l i c a t i o n sG H i g h b a n d w i d t h,l o w r e s i s t a n c e,R T D,P S T N a n d3-w i r e t r a n s m i t t e r v e r s i o n s a v a i l a b l eA n a l o g u e i n p u t s(h i g h-l e v e l)2-w i r e t r a n s m i t t e r s,4-20m A,c o n v e n t i o n a l a n d s m a r tThe SPDs recommended for use with ‘conventional’and ‘smart’ 4-20mA transmitters(fed by a well-regulated supply) are the SD32 and SD55, the choice depending upon the maximum working voltage of the system (32V and 55V respec-tively). The diagram illustrates a prime exam-ple of an application for which the fuse/dis-connect facility is particularly useful, however, both models are available in ‘X’ versions with-out the optional fuse/disconnect feature.A n a l o g u e i n p u t s(l o w-l e v e l)R T D sThese applications are best served using the SD RTD. F or optimum accuracy, the energising current should be chosen to ensure the voltage across the RTD does not exceed 1V over the full measurement range. When using a PT100 device, we recommend an energising current of 1mA.P h o t o c e l l s,T H C s,m V s o u r c e s a n d t u r b i n ef l o w m e t e r sThe SD07 or SD16 (depending upon the operational voltage) are the favoured choices for this application. SD07X and SD16X are also suitable.F I E L D C I R C U I T P R O T E C T E D C I R C U I T2-w i r e t r a n s m i t t e r s3w i r e R T D sp h o t o c e l l s,T H C s,m V s o u r c e s a n dt u r b i n e f l o w m e t e r sAlso, loops can be removed from the circuit for maintenance reasons or added without needing additional disconnect terminals. The following guide to selection suggests the most suitable SDs for a number of specific applications. For technical information, see the detailed specifications on the back page of this publication (some field circuit protection is shown for completeness).D i g i t a l(o n/o f f)i n p u t sS w i t c h e sSuitable SPDs for switches include the SD07, SD16, SD32 and SD55 modules – the choice depending upon the operating voltage of the sys-tem. The ‘X’ versions of these are also suitable.D i g i t a l(o n/o f f)o u t p u t sA l a r m s,L E D s,s o l e n o i d v a l v e s,e t cThe recommended choice for this application is the SD32 or SD32X.T e l e m e t r y(P S T N)T e l e m e t r y o u t s t a t i o n sThe SD PSTN has been designed specifically for the protection of signals transmitted on public switched telephone networks.A C s u p p l i e d e q u i p m e n tP L C,I/O s y s t e m sFor systems on 110-120V ac, the SD150X is the recommended choice and for 220-240V ac sys-tems, the SD275X is recommended.C o n t r o l l e r o u t p u t s (I/P c o n v e r t e r s)S w i t c h e sA l a r m s,L E D s,s o l e n o i d v a l v e s,e t c. T e l e c o m l i n eP L C,I/O s y s t e m s2-w i r e t r a n s m i t t e r s o r s e n s o r s4-20m A t r a n s m i t t e r s,c o n v e n t i o n a l a n ds m a r tWhere the TP48 is not an acceptable solution,either because of technical suitability ordifficulties in mounting, the SD16X, SD32X andSD55X are an excellent alternative.3-w i r e t r a n s m i t t e r s o r s e n s o r sVibration Sensors and 4-20mA loop processcontrol systems invariably require threewire connections, when powered from anexternal source.This may be accomplished in one unit by usingthe SD32T3 three terminal Surge ProtectionDevice (SPD).Because the SD32T3 protects all threeconductors within the same unit, higherprotection is achieved, as the SPD hybridcircuitry is common to all three wires.The SD07R3 is available for the protection of 3-wire pressure transducers on low powercircuits.4-w i r e t r a n s m i t t e r s o r s e n s o r sF l o w m e t e r s,l e v e l d e t e c t o r s,e t c.4-wire systems such as level detectors requiretwo SDs, one for the supply and the other forthe transmitter output. Generally the voltagesacross the pairs are similar and so therecommended choice would be a pair ofSD16X, SD32X or SD55Xs. However, mainspowered transmitters should be protected withan SD150X or 275X (depending upon supplyvoltage) for the supply inputs.Loadcells are catered for by MTL SurgeTechnologies’ LC30 which is suitable for both 4and 6-wire load cells.2-w i r e t r a n s m i t t e r o r s e n s o r3-w i r e t r a n s m i t t e r o r s e n s o r4-w i r e t r a n s m i t t e r o r s e n s o rS D P R O T E C T E D F I E L D C I R C U I T T O H O S T C I R C U I T2by fixing the metallic transmitter housing to the plant structure. This bond ensures the voltage difference between the signal conductors and the transmitter housing is below the transmitter’s insulation rating. Please note that the transmitters or sensors are connected to the ‘Protected Equipment’ terminals of the SD and not the ‘Field Cables’.C o m m u n i c a t i o n s y s t e m sR S 232, R S 422, R S 485The recommended choice for these applications isthe SD16R or SD32R depending on the maximumdriver signal.B u s p o w e r e d s y s t e m sThere are a variety of bus powered systemsspecially designed for the process industry. Theideal surge protection device for these systemsis the SD32R as it has a very high bandwidth anda modest in-line resistance.T y p i c a l A p p l i c a t i o n sTable 1 shows suitable SD devices for differentapplications. In some applications alternativedevices may be used, for example, where lowerin-line resistance or a higher voltage powersupply is used.Telematic have operationally tested therecommended SD series with representativehighways listed but no formal approval for theiruse in systems by the respective bodies hasbeen sought.R S 232, R S 422, R S 485B u s p o w e r e d s y s t e m s T a b l e 1 P R O T E C T E D F I E L D C I R C U I T S D P R O T E C T E D H O S T C I R C U I T A p p l i c a t i o n P r e f e r r e d S P D A l t e r n a t i v e Allen Bradley Data Highway Plus SD16R Foundation Fieldbus 31.25kbits/s voltage mode SD32R 1.0/2.5 Mbits/s SD55R HART SD32X SD32, SD32R Honeywell DE SD32X SD32, SD32R LonWorks FFT-10SD32R LPT-10SD55RTP-78SD07RIS78†SD32RModbus ‘& Modbus Plus (RS485)SD16RPROFIBUSDP SD32RPA (IEC 1158, 31.25 kbits/s)FP32RS232SD16SD16XRS422SD07RRS423SD07RRS485SD07RWorldRP (IEC 1158)SD32R31.25 kbits/s voltage mode1.0/2.5 Mbits/s SD55RE a r t h i n g The recommended earthing for field mounted devices has been illustrated previously but it is the earthing at the control panel that is more critical as there are usually a number of earthing systems, each with their own requirements. The earthing system illustrated here replaces the instrument 0V bond, the control system PSU bond and the IS earth with one single earth connection to meet all the design requirements and give the most effective protection against the effects of lightning induced surges.outdoor installation where there is a highlikelihood of both lightning induced transientsand combustible gases requires the installationof SPDs to prevent possible ignition of thegases. Areas seen particularly at risk includeflammable liquid storage tanks, effluenttreatment plants, distillation columns inpetrochemical works and gas pipelines.SPDs for transmitter protection should beinstalled in Zone 1 but sufficiently close to theZone 0 boundary to prevent high voltagesentering Zone 0. The distance from the SPDto Zone 0 should be less than one metrewhere possible. However, in practice the SPDwould normally be mounted on the transmitteror sensor housing which usually lies in Zone 1and is very close to Zone 0. Because there isonly a very small free volume, the SD Series issuitable for mounting in flameproof orexplosion proof enclosures.Z o n e 2The SD series is suitable for protecting electricalcircuits in Division 2, Zone 2 and can be usedwithout affecting the safety aspects of the circuit.Non-incendive (low-current) circuits can beprotected using any SD series unit mounted ineither the safe or hazardous area including thosewith the fuse disconnect facility. Non arcing (highcurrent) circuits can also be protected exceptthat SPDs with the fuse disconnect facility mayonly be mounted in the safe area. F or use inthese circuits the units must be mounted in asuitable enclosure, normally the minimumrequirements are IP54 and 7Nm resistance toimpact. The SD series is self certified byTelematic Ltd as being suitable for this purpose.C e r t i f i c a t i o nIntroducing surge protection into IntrinsicallySafe (IS) circuits is trouble free as long as thecurrent and power parameters are notexceeded. In the SD Series, the SD**X, SD**R,SD**R3, SD RTD and SD**T3 all have ATEXcertification for use in IS circuits located inZones 0, 1 or 2. The certification parametersfor the SD**X and SD**T3 are:E E x i a I I C T 4, Li = 0.22mHIi = 260mA for Ui up to 20VIi = 175mA for Ui up to 26VIi = 140mA for Ui up to 28VIi = 65mA for Ui up to 60VThe certification parameters for the SD**R,SD**R3 and SD RTD are:E E x i a I I C T 4, Li = 0Ii = 260mA for Ui up to 60VThe power rating for each of the above isdependent on the table shown below.Pi = 1W (–30°C to +75°C)Pi = 1.2W (–30°C to +60°C)Pi = 1.3W (–30°C to +40°C)The SD** Series are classifed as simpleapparatus and are intended for use in Zone 2 orsafe areas only, because their fuses are not fullyencapsulated.the tops of individual SPDs. Both methods can be used conjointly. Replaceable fuses or solid links are available in packs of 5 (SD-F25, SD-F05 and SD-LNK).M o u n t i n g a c c e s s o r i e sISP7000Insulating spacerTHR2Standard DIN rail, 35mm x 7.5mmTHR7000T-section DIN rail, specially nickel plated,35mm x 7.5mm, 1m lengthE a r t h i n g /e a r t h r a i l a c c e s s o r i e sETL7000Earth terminal, DIN rail mountedIMB57Insulated mounting block (two needed)ERB57S Earth rail bracket, straightERB57O Earth rail bracket, offsetERL7Earth rail, 1m lengthETM7Earth terminal, pack of 50T a g g i n g a c c e s s o r i e sTAG57Tagging strip, 1m lengthTGL57Tagging strip labels, set of 10 x 0.5mBRI7000Barrier identifierBIL7000Barrier indentification labels, sheet of 120BIL7000L Barrier identification labels, A4 sheet of 126E n c l o s u r e sDX070Enclosure for up to 9 x SD series SPDsDX170Enclosure for up to 22 x SD series SPDsDX430Enclosure for up to 58 x SD series SPDsA c c e s s o r i e s (r e p l a c e m e n t )SD-F25Replaceable fuse pack - 250mA standard(available in packs of 5)SD-F05Replaceable fuse pack - 50mA special(available in packs of 5)SD-LNK Solid Link (available in packs of 5)D I M E N S I O N S (m m )C o u n t r y S t a n d a r d C e r t i f i c a t e /A p p r o v e d f o r P r o d u c t(A u t h o r i t y )F i l e N o .BASEEFA EN 50014:1997BASEEFA EEx ia IIC T4*SD07X,SD16X,SD32X,(EC)EN 50020:200202ATEX0211X SD55X,SD07R, SD16R,EN 50284:1999SD32R,SD55R,SDRTD,SD32T3,SD07R3,SD16R3,SD32R3,SD55R3CSA/C/US CSA C22.2 No. 0-M1991LR 103652-3EEx ia Class 1,SD07,SD16,SD32,SD55, (Canada, USA)CSA C22.2 No. 157-M1992Groups A, B SD07X,SD16X,SD32X, UL 913, 5th edition C and D, T4SD55X,SD07R,SD16R,CSA C22.2 No. 142-M1987Class 1, Div 2 SD32R,SD55R,SDRDT , CSA C22.2 No. 213-M1987Groups A,B,C, D T4SD32T3,SD07R3,SD16R3, UL 508, 17th edition SD32R3,SD55R3UL 1604, 3rd edition UL UL 497B Listed E220693Isolated loop SD07,SD16,SD32,SD55(USA)communication SD07X,SD16X,SD32X circuits SD55X,SD07R,SD16R SD32R,SD55R,SD07R3SD16R3,SD32R3,SD55R3SD32T3,SD55T3, SD07X3,SD16X3,SD32X3,SD55X3,SDRTD UL UL 1449 2nd Edition E217523AC power SD150X,SD275X (USA, Canada)Recognised Component protection Austel AS/NZ3548:1995__Private Wire SD07R (Australia)AS/NZS4117:1996TS001: 1997901-107 R e v H 5/03/06Note: all figures are typical at +25°C unless otherwise stated; *standard fuse; +over full working temperature range; †at 20mA with a 250mA standard fuse; ‡these units need external 3A fuses; ^Signal; **Power & Common; maximum energising current depends upon RTD resistance.820(10/350µs )2.5kA1.0kA (SD150X and SD275X only)R e s p o n s e t i m e<1nsR T D r e s i s t a n c e r a n g e (S D R T D )10 to 1500ΩD e g r a d a t i o n a c c u r a c y (S D R T D a t 1m A )0.1% (RTD resistance >100Ω)0.1Ω(RTD resistance < 100Ω)A m b i e n t t e m p e r a t u r e–40°C to +80°C (working)–40°C to +80°C (storage)H u m i d i t y5 to 95% RH (non-condensing)C a t e g o r y t e s t e dA2, B2, C1, C2, C3O v e r s t r e s s e d f a u l t m o d e i n =3k A12kA9kA (SD150X and SD275X only)I m p u l s e d u r a b i l i t y (8/20μs )10kA6.5kA (SD150X and SD275X only)T e r m i n a l s2.5mm 2(12 AWG)M o u n t i n gT-section DIN-rail(35 x 7.5 or 35 x 15mm rail)W e i g h t70g approximatelyC a s e f l a m m a b i l i t yUL94 V-2A C d u r a b i l i t y1A rms , 5TS e r v i c e c o n d i t i o n s80kPa - 160kPa5% - 95% RHE M C c o m p l i a n c eTo Generic Immunity Standards,EN 50082, part 2 for industrialenvironmentsR &T T E c o m p l i a n c eEN 50082-2 : 1995EN 41003 : 1999EN 60950 : 1992(not applicable to SD150X andSD275X)L V D c o m p l i a n c eSD150X & SD275XEN 60950 : 1992EN 61010 : 1995SD PSTNEN 41003 : 1999I E C c o m p l i a n c eEN 61643-21:2001T o o r d e r s p e c i f y -Order by module, as listed in the specification table and/or accessory part numbers as defined on page 7.Note: In accordance with our policy of continuous improvement, we reserve the right to change the product’s specification without notice.D e f i n i t i o n s o f t e r m i n o l o g y u s e d i n t a b l e 1W o r k i n g v o l t a g e (U n )Maximum voltage between lines or lines/ ground for the specified leakage current 2M a x i m u m l e a k a g e c u r r e n t (I c )Maximum current drawn by the SPD at the working voltage 3M a x i m u m c o n t i n u o u s o p e r a t i n g v o l t a g e (U c )Maximum voltage that can be applied to the protected terminals without damage 4V o l t a g e p r o t e c t i o n l e v e l (U p )Peak output voltage after injection of test impulse from 1kV/μs generator (often known as ‘let-through’ voltage)5B a n d w i d t h Frequency range up to which ac signals can be transmitted without undue attenuation; 3dB into 50Ω(600Ωfor the SD PSTN )A p p r o v a l s * See page 6 for further details M T L S u r g e T e c h n o l o g i e s Power Court, Luton, Bedfordshire, England LU1 3JJ Tel:+44(0)1582 723633 Fax: +44 (0)1582 422283E-mail:***********************:A m e m b e r o f t h e M T L I n s t r u m e n t s G r o u p p l c Blue colour signifies products ATEX certified EEx ia IIC T4.。
MS05马达 A07441N
10.5 [0.41]
11.3 [0.44]
11.25 [0.44]
30 [1.18]
35 [1.38]
见 “ 制动器” 部分
波克兰液压
1 G 1 0 Ø 92.7 Ø 140
Ø 170
201.2
Ø 228
Ø 18
10 x
-
1 2 3 4 [3.65 dia.] [5.51 dia.] [6.69 dia.] [7.92] [8.98 dia.] [0.71 dia.] M14x1.5
29 [39]
优先旋向 kW [HP]
19 [25] 19 [25]
19 [25]
19 [25]
非优先旋向 kW [HP]
15 [20] 15 [20]
15 [20]
15 [20]
tr/min [RPM]
265 250 240 220 200 200 190 175 160 145
200
bar [PSI]
41 kg [90 lb] 52 kg [114 lb] 0.50 L [30 cu.in] 0.50 L [30 cu.in]
轮边马达
轴马达
配流系统和液压基块
制动器
选项
01/07/2005
见 “ 配流系统和液压基块” 部分
9 / 32
模块化液压马达 MS05 - MSE05
轴承支撑类型 MS 0 5
[3.77 dia.] [5.51 dia.] [7.09 dia.] [5.72]
Ø 92.7 Ø 140
Ø 180
145.4
[3.65 dia.] [5.51 dia.] [7.09 dia.] [5.72]
S型全热产品说明书
型号
L
670 670 735 735
L1 W
65 65 75 75 55 0 55 0 63 0 63 0 85 0 85 0
W1 H
60 60 60 60 80 80 200 200 250 250
H1
100 100 125 125
D
E
F
D
G
19 19 19 19
W
W1
M
N
308 590 597 291 590 597 3 92 6 5 5 6 7 7 3 40 6 5 5 6 7 7
QFA-D1000S QFA-D1000S-Y 静压-风量性能曲线
600 500 400
高档
600 500 400 300
低档 低档
高档
300 200 100 0 200 400 600 800 1000 1200 1400 1600 1800 2000
QFA-D1500S QFA-D1500S-Y 静压-风量性能曲线
安装实例
备注：1 .必须安 装2个 室 外 风道（室内新 风 管 道 和排风管道） ， 以 防 止冷凝； （材 料 ： 保温材料， 厚 度 ：2 5 m m） 2 .检 修 空 间必须预留检 查 盖 下 方300以上。
Q FA-D 150 S-Y
线控型（普通型不表示） 薄型 风量150m³/ h 吊顶式安装 新风设备 全热型
保修卡 姓 名 电 话 年 月 日
单位或地址 保修期限
购买日期
1、 本 产 品 整 机 维 修 一 年,在 正 常 使 用 状 况 下 免 费 维 修 。 2、 保 修 期 的 起 始 日 期 以 产 品 发 票 日 期 为 准 。 3、 维 修 时 请 出 示 发 票 。 4、 在 保 修 期 间 ， 若 有 下 列 情 况 恕 不 免 费 维 修 。 •由 于 没 有 按 说 明 书 上 要 求 使 用 而 造 成 故 障 的 。 •由 于 自 行 修 理 改 装 以 致 损 坏 的 。 •由 于 不 可 抗 力 因 素 所 造 成 的 故 障 或 损 坏 的 。 •由 于 非 正 常 使 用 （ 如 长 时 间 使 用 于 环 境 恶 劣 的 场 所 或 车 辆 、 船舶上搭载）所造成之故障或损坏的。 •由 于 人 为 敲 击 、 摔 、 撞 、 切 、 割 等 损 坏 的 。 5、 超 过 保 修 期 或 不 属 于 免 费 保 修 的 产 品 ， 本 公 司 的 特 约 维 修 点 仍竭诚为您服务。
YM12S05-G;中文规格书,Datasheet资料
Turn-On Delay Time Full resistive load With Vin = (Converter Enabled, then Vin applied) From Vin = Vin(min) to Vo=0.1* Vo(nom) With Enable (Vin = Vin(nom) applied, then enabled) From enable to Vo= 0.1*Vo(nom) Rise time (Full resistive load) ON/OFF Control 2 Converter Off Converter On
Description Power-One’s point-of-load converters are recommended for use with regulated bus converters in an Intermediate Bus Architecture (IBA). The YM12S05 non-isolated DC-DC converters deliver up to 5A of output current in an industry-standard surface-mount package. Operating from a 9.6-14 VDC input, the YM12S05 converters are ideal choices for Intermediate Bus Architectures where Point-of-Load power (POL) delivery is generally a requirement. They provide an extremely tight regulated programmable output voltage of 0.7525 V to 5.5 V. The Y-Series converters provide exceptional thermal performance, even in high temperature environments with minimal airflow. No derating is required up to 85 C (up to 70 C for 5 V and 3.3 V outputs), even without airflow at natural convection. This is accomplished through the use of advanced circuitry, packaging and processing techniques to achieve a design possessing ultra-high efficiency, excellent thermal management and a very low body profile. The low body profile and the preclusion of heat sinks minimize impedance to system airflow, thus enhancing cooling for both upstream and downstream devices. The use of 100% automation for assembly, coupled with advanced power electronics and thermal design, results in a product with extremely high reliability.
至拉斯科普的CD、AD和BD系列脱水干燥器说明书
ATLAS COPCO DESICCANT AIR DRYERS FOR SIMPLE RELIABILITYCD series (360-1600 l/s, 763-3392 cfm) AD series (360-3450 l/s, 763-7314 cfm) BD series (360-3450 l/s, 763-7314 cfm)THE RIGHT DESICCANT DRYER FOR YOUR APPLICATIONA dry compressed air system is essential to maintain the reliability of production processes and the quality of your end products. Untreated air can cause corrosion in pipe work, premature failure of pneumatic equipment, and product spoilage. Atlas Copco’s desiccant dryers produce dry compressed air in a reliable and energy-efficient way while protecting your systems and processes.Working principleDesiccant dryers or twin tower dryers consist of two towers filled withdesiccant such as activated alumina or silica gel. While one tower isdrying compressed air, the other is being regenerated. Desiccantdryers can achieve dewpoints of down to -40°C/-40°F and -70°C/-100°F.Why desiccant dryers?Robust design.Total reliability.A constant, stable dewpoint in full load conditions.High reliabilityCompressed air entering the air net is always 100% saturated. When it cools, the moisture will condense, causing damage to your air system and finished products. Removing moisture from compressed air with a pressure dewpoint as low as -40°C/-40°F, Atlas Copco desiccant dryers eliminate system failures, production downtime and costly repairs.Competitive performanceA dewpoint down to -40°C/-40°F together with simple and easy controls guarantee the dryer operates in the best way possible.Good efficiencyProperly sized pipes and valves ensure a limited pressure drop. Several options are available to increase the efficiency and to reduce the energy consumption.Limited maintenanceAtlas Copco dryers have a small footprint thanks to the all-in-one design. Delivered ready for use, installation is straightforward, minimizing costly production downtime. All internal components are easily accessible to facilitate maintenance. The use of high-grade desiccant and high-quality valves results in three-year maintenance intervals.Assuring your peace of mindThrough continuous investment in our competent, committed and efficient service organization, Atlas Copco ensures superior customer value by maximizing productivity. With a presence in over 170 countries, we offer professional and timely service through interaction and involvement. Uptime is guaranteed by dedicated technicians and 24/7 availability.Blower purge dryers use a combination of air from an external blower, heat and minimal compressed air.Dry air from the outlet of the drying tower is expanded to atmospheric pressure and sent through the saturated desiccant, forcing the adsorbed moisture out (2) (4). After desorption, the blow-off valve is closed and the vessel is re-pressurized.The drying processThe regeneration processWet compressed air flows upward through the desiccant which adsorbs the moisture, from bottom to top (1).HEATLESS DESICCANT DRYERS4312Dry airWet airAfter regeneration, the functions of both towers are switched (3).SwitchingAWet compressed air flows upward through the desiccant which adsorbs the moisture, from bottom to top (1).Dry air from the outlet of the drying tower is expanded to atmospheric pressure (4) and sent over the heater (5). The heated air is then sent through the saturated desiccant (2) forcing the adsorbed moisture out, from top to bottom. After the heating process, the hot tower desiccant is cooled. Cooling is done by expanding dry compressed air from the outlet over the hot reactivated tower, from top to bottom.The blower (5) takes ambient air and blows it over the external heater (6). The heated air is then sent through the saturated desiccant (2), forcing the adsorbed moisture out, from top to bottom. After the heating, the hot tower desiccant is cooled. Cooling is done by expanding dry compressed air from the outlet of the adsorbing vessel over the hot reactivated tower, from top to bottom.After regeneration, the functions of both towers are switched (3).After regeneration, the functions of both towers are switched (3).BLOWER PURGE DESICCANT DRYERSThe drying processThe regeneration processSwitchingSwitching53124Dry airWet air56312Dry airWet airHigh-quality desiccantReliable high adsorption capacity desiccant for maximum performance. Pressure dewpoint of -40°C/-40°F .1Butterfly valvesHigh-performance butterfly valves with actuators ensure long lifetime.2Galvanized piping with flanged connectionsFlanged piping simplifies maintenance and minimizes the chance of leakages. Properly sized piping.3FiltersPre-filter(s) protect desiccant against oil contamination, increasing the lifetime of the desiccant. After-filter protects the network against desiccant dust, avoiding network contamination. Mounted directly on the inlet and outlet of the dryer, for easy assembly.4CubicleIP 54 protected.Electronic control board. Time-based steering. Load/unload freeze contact.5Robust and compact designStandard frame, including forklift slots and lifting eyes for easy handling. Vessel connecting flanges are integrated into the top and bottom shells, lowering the total unit height.6Check valveNickel-plated. Wafer type.With integrated fixed nozzle.71High-quality desiccantReliable high adsorption capacity desiccant for maximum performance.Pressure dewpoint of -40°C/-40°F.2Butterfly valvesHigh-performance butterfly valves with actuators ensure long lifetime.3Galvanized piping with flanged connectionsGalvanized piping simplifies maintenance and minimizes the chance of leakages.Properly sized piping.4Low-watt density heaterStainless steel design to ensure long lifetime.Galvanized heater pipe protects against corrosion.Heater is installed in an insulated heater pipe to assure the most energy-efficient setup.5Filters (optional)Pre-filter(s) protect desiccant against oil contamination, increasing the lifetime ofthe desiccant.After-filter protects network against desiccant dust, avoiding network contamination.Mounted directly on the inlet and outlet of the dryer, for easy assembly.6Advanced control and monitoring systemFitted inside a real IP54 cubicle for easy cablingand safety.Monitoring of all parameters to ensure maximum reliability for your installation.7Robust and compact designStandard frame, including forklift slots and lifting eyes for easy handling.Vessel connecting flanges are integrated intothe top and bottom shells, lowering the totalunit height.8Check valveNickel-plated.Wafer type.High-quality desiccantReliable high adsorption capacity desiccant for maximum performance. Pressure dewpoint of -40°C/-40°F .1Butterfly valvesHigh-performance butterfly valves with actuators ensure long lifetime.2Galvanized piping with flanged connectionsGalvanized and properly sized piping simplifies maintenance and minimizes the chance of leakages.3Low-watt density heaterStainless steel design to ensure long lifetime. Galvanized heater pipe protects against corrosion. Heater is installed in an insulated heater pipe to assure the most energy-efficient setup.4Advanced control and monitoring systemFitted inside a real IP54 cubicle for easy cabling and safety. Monitoring of all parameters to ensure maximum reliability for your installation.6Robust and compact designStandard frame, including forklift slots and lifting eyes for easy handling. Vessel connecting flanges are integrated into the top and bottom shells, lowering the total unit height.7Filters (optional)Pre-filter(s) protect desiccant against oil contamination, increasing the lifetime of the desiccant.After-filter protects network against desiccant dust, avoiding network contamination. Mounted directly on the inlet and outlet of the dryer, for easy assembly.5Atlas Copco's Elektronikon ® control and monitoring system takes continuous care of your desiccant dryer to ensure optimal productivity and efficiency at your site.ADVANCED CONTROL ANDMONITORINGAvailable in 32 languages, this graphical 3.5-inch high-definition color display with pictograms and LED indicators for key events is easy to use. The keyboard is durable to resist tough treatment in demanding environments.Valuable items of information displayed include the ServiceP lan indicator and preventive maintenance warnings.User-friendly interfaceComprehensivemaintenance display® system monitors and displays key parameters such as dewpoint, vessel pressure and inlet temperature, and includes an energy-savings indicator. Internet-based visualization of your dryeris possible by using a simple Ethernet connection.AIRConnect™ is an optional advanced remote monitoring package that offers complete analysis and accurate management. It is fully customizable to meet specific customer needs, from simple alarm notification via email or SMS to visualization via fieldbus, LAN or internet, including advanced reporting services.Control and monitoringInternet-based visualizationAIRConnect™OPTIMIZE YOUR SYSTEM Scope of supply: Not available : OptionalTECHNICAL SPECIFICATIONSHeatless desiccant dryersHeated purge desiccant dryersBlower purge desiccant dryersReference conditions:Compressed air inlet temperature: 35°C/100°F .Inlet relative humidity: 100%.Dryer inlet pressure for 11 bar variants, after inlet filtration.6996 1037 01 – P r i n t e d i n C h i n a - S u b j e c t t o a l t e r a t i o n w i t h o u t p r i o r n o t i c e . N e v e r u s e c o m p r e s s COMMITTED TO SUSTAINABLE PRODUCTIVITYWe stand by our responsibilities towards our customers, towards the environment and the people around us. We make performance stand the test of time. This is what we call — Sustainable Productivity.。
硫化镉光敏电阻器(PGM)规格书
1.0 2.0 5.0 10 20 20
0.6 0.7 0.7 0.8 0.8 0.8
30 30 30 30 30 30
40 30 30 30 30 30
德键电子工业股份有限公司
Version 2014
TOKEN
20mm CDS 光敏电阻器 - PGM 系列 外形尺寸
PGM20 CDS光敏电阻器
Ø20.5MAX
性 能 湿度 > 95% Drift of R10 = ± 20% 没有明显的损伤 Drift of R10 = ± 30% 没有明显的损伤 没有明显的损伤
没有明显的损伤 没有明显的损伤
料号标识
PGM5516 型号 包装方式 p
Version 2014
德键电子工业股份有限公司
03 of 07
Ø0.6 17.5
环氧树脂封装 (PGM 20mm) 外观
环氧树脂封装 (PGM 20mm) 尺寸
Plastic Case Ø 22 5 Epoxy Resin 17.5
金属外壳封装 (PGM 20mm) 外观
备注： 尺寸的单位是 (mm)， 且各部分尺寸不一。
金属外壳封装 (PGM 20mm) 尺寸
PGM5 CDS光敏电阻器
暗电阻 (MΩ)min 0.15 0.2 1.0 2.0 5.0 10.0 1.0 2.0 5.0 10.0 20.0 20.0
γ min 0.6 0.6 0.6 0.7 0.8 0.8 0.6 0.6 0.7 0.8 0.8 0.8
响应时间(ms) 上升 30 30 20 20 20 20 20 20 20 20 20 20 下降 40 40 30 30 30 30 30 30 30 30 30 30
MSC050SDA070B 零回收碳纤维氧化钙晶体瓷液晶体电对称扬音器说明书
MSC050SDA070BDatasheet Zero Recovery Silicon Carbide Schottky DiodeFinalMay 2018Contents1Revision History (1)1.1Revision A (1)2Product Overview (2)2.1Features (2)2.2Benefits (2)2.3Applications (2)3Electrical Specifications (3)3.1Absolute Maximum Ratings (3)3.2Electrical Performance (4)3.3Performance Curves (5)4Package Specification (7)4.1Package Outline Drawing (7)1Revision HistoryThe revision history describes the changes that were implemented in the document. The changes arelisted by revision, starting with the most current publication.1.1Revision ARevision A was published in May 2018. It is the first publication of this document.2Product OverviewThis section shows the product overview for the MSC050SDA070B device.2.1FeaturesThe following are key features of the MSC050SDA070B device:Ultra-fast recovery timesSoft recovery characteristicsLow forward voltageLow leakage currentAvalanche energy ratedRoHS compliant2.2BenefitsThe following are benefits of the MSC050SDA070B device:High switching frequencyLow switching lossesLow noise (EMI) switchingHigher reliability systemsIncreased system power density2.3ApplicationsThe MSC050SDA070B device is designed for the following applications: Power Factor Correction (PFC)Anti-parallel diodeSwitch-mode power supplyInverters/convertersMotor controllersFreewheeling diodeSwitch-mode power supplyInverters/convertersSnubber/clamp diode3Electrical SpecificationsThis section shows the electrical specifications for the MSC050SDA070B device.3.1Absolute Maximum RatingsThe following table shows the absolute maximum ratings for the MSC050SDA070B device.All ratings: T= 25 °C unless otherwise specified.CTable 1 • Absolute Maximum RatingsSymbol Parameter Ratings UnitV R Maximum DC reverse voltage700VV RRM Maximum peak repetitive reverse voltage700V RWM Maximum working peak reverse voltage700I F Maximum DC forward current (T = 25 °C)c88AMaximum DC forward current (T = 135 °C)c39Maximum DC forward current (T = 145 °C)c32128I FRM Repetitive peak forward surge current(T = 25 °C, t= 10 ms, half sine wave)c p124I FSM Non-repetitive forward surge current(T = 25 °C, t= 10 ms, half sine wave)c pP tot Power dissipation (T = 25 °C)c283WPower dissipation (T = 110 °C)c123T , TJ STG Operating and storage temperature range–55 to 175°CT L Lead temperature for 10 seconds300100mJE AS Single-pulse avalanche energy(starting T = 25 °C, L = 0.08 mH, peak I = 50 A)J LThe following table shows the thermal and mechanical characteristics of the MSC050SDA70B device.Table 2 • Thermal and Mechanical CharacteristicsSymbol Characteristic Min Typ Max UnitRθJC Junction-to-case thermal resistance0.370.53°C/WW T Package weight0.22oz5.9gMounting torque, 6-32 or M3 screw10lbf-in1.1N-mThe following table shows the static characteristics of the MSC050SDA070B device.Table 3 • Static CharacteristicsSymbol Characteristic Test Conditions Typ Max UnitV F Forward voltage I = 50 A, T = 25 °CF J 1.5 1.8VI = 50 A, T = 175 °CF J 1.9I RM Reverse leakage current V = 700 V, T = 25 °CR J15200μAV = 700 V, T = 175 °CR J250Q C Total capacitive charge V = 400 V, T = 25 °CR J133nCC J Junction capacitance V = 1 V, T = 25 °C, ƒ = 1 MHzR J2034pFJunction capacitance V = 200 V, T = 25 °C, ƒ = 1 MHzR J248Junction capacitance V = 400 V, T = 25 °C, ƒ = 1 MHzR J216This section shows the typical performance curves for the MSC050SDA070B device.Figure 1 • Maximum Transient Thermal ImpedanceFigure 2 • Forward Current vs Forward Voltage Figure 3 • Max Forward Current vs Case TempFigure 4 • Max Power Dissipation vs Case Temp Figure 5 • Reverse Current vs. Reverse VoltageFigure 4 • Max Power Dissipation vs Case Temp Figure 5 • Reverse Current vs. Reverse VoltageFigure 6 • Total Capacitive Charge vs. Reverse Voltage Figure 7 • Junction Capacitance vs Reverse Voltage4Package SpecificationThis section outlines the package specification for the MSC050SDA070B device.4.1Package Outline DrawingThis section shows the TO-247 package drawing of the MSC050SDA070B device. Dimensions are inmillimeters and (inches).Figure 8 • Package Outline DrawingMicrosemi Corporate HeadquartersOne Enterprise, Aliso Viejo,CA 92656 USAWithin the USA: +1 (800) 713-4113Outside the USA: +1 (949) 380-6100Fax: +1 (949) 215-4996Email:***************************© 2018 Microsemi Corporation. All rights reserved. Microsemi and the Microsemi logo are trademarks of Microsemi Corporation. All other trademarks and service marks are the property of their respective owners.Microsemi makes no warranty, representation, or guarantee regarding the information contained herein or the suitability of its products and services for any particular purpose, nor does Microsemi assume any liability whatsoever arising out of the application or use of any product or circuit. The products sold hereunder and any other products sold by Microsemi have been subject to limited testing and should not be used in conjunction with mission-critical equipment or applications. Any performance specifications are believed to be reliable but are not verified, and Buyer must conduct and complete all performance and other testing of the products, alone and together with, or installed in, any end-products. Buyer shall not rely on any data and performance specifications or parameters provided by Microsemi. It is the Buyer's responsibility to independently determine suitability of any products and to test and verify the same. The information provided by Microsemi hereunder is provided "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the Buyer. Microsemi does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other IP rights, whether with regard to such information itself or anything described by such information. Information provided in this document is proprietary to Microsemi, and Microsemi reserves the right to make any changes to the information in this document or to any products and services at any time without notice.Microsemi Corporation (Nasdaq: MSCC) offers a comprehensive portfolio of semiconductor and system solutions for aerospace & defense, communications, data center and industrial markets. Products include high-performance and radiation-hardened analog mixed-signal integrated circuits, FPGAs, SoCs and ASICs; power management products; timing and synchronization devices and precise time solutions, setting the world's standard for time; voice processing devices; RF solutions; discrete components; enterprise storage and communication solutions; security technologies and scalable anti-tamper products; Ethernet solutions; Power-over-Ethernet ICs and midspans; as well as custom design capabilities and services. Microsemi is headquartered in Aliso Viejo, California, and has approximately 4,800 employees globally. Learn more at .053-4080。
0805 ESD Suppressor SMD尺寸数据手册说明书
Artikelnummer / part number :823 50 120 101Datum / Date :2006-10-15Bezeichnung :description :0805 ESD SuppressorSMD size:0805A Mechanische Abmessungen / dimensions :SIZE(Unit : mm)B Elektrische Eigenschaften / electrical properties :TECHNICAL DATAWorking Max. ClampingTyp.Leakage ESD Pulse ESD Voltage Voltage Voltage Clamp. V Current Withstandair dischargeDC V(*1)V (*2)µA (*3)kV (*4)pF Spezifikation für Freigabe / specification for releasePart NumberKunde / customer :CapacitanceROHS Compliant823 50 120 1011250-1-+/-15100* 1 Max. Clamping Voltage at 8/20 waveformand 1 A pulse current Capacitance tolerance:+/-30%* 2 Typ. Clamping Voltage per 8 kV ESD contact discharge methodCapacitance measured at:1MHz* 3 Leakage Current at max operating voltage, the max leakage current was measured at reliability test * 4. ESD Typ. Withstands Voltage design and method guarantee this propertyWAVE FORMESD LEVEL IEC61000-4-2Severity Level Air DischargeDirect Discharge1 2 kV 2 kV 2 4 kV4 kV 38 kV 6 kV 415 kV 8 kV 5Special SpecialREFERENCE DATA Response timeT rise <1ns Operating ambientg temperature -40～+85℃Storage temperature -50～+125℃Max. temperature solder 260/10s℃OTHER DATA BodyZnO End termination Ag/Ni/Sn PackagingReelComplies with Standard IEC61000-4-2Procedure Solgel MarkingNoneD-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Würth Elektronik eiSos GmbH & Co.KG - Radialex departmentArtikelnummer / part number :823 50 120 101Bezeichnung :description :0805 ESD SuppressorSMD size:0805C Lötpad / soldering spec. :RECOMMENDED SOLDER PAD LAYOUT (Unit : mm)1 - The solder paste shall be printed in a thickness of 150 to 200µm.2 - The SIR test of the solder paste shall be done （Based on JIS-Z-3284）3 - IR reflow Pb Free Process suggestin profile (Based on J-STD-020-C):Spezifikation für Freigabe / specification for releaseKunde / customer :Rapid heating, partial heating or rapid cooling will easily cause defect of the component. So preheating and gradual cooling process is suggested. IR soldering has the highest yields due to controlled heating rates and solder liquidus times. Make sure that the element is notSoldering recommend paste is Sn 96.5/Ag 3.5- Preheat1.The temperature rising speed is suggested to be 2~3℃/s.2.Appropriate preheat time will be from 60 to 120 seconds.3.Temp. maintain at 175 +/-25°C 120 seconds. - Heating1.Careful about sudden rise in temperature as it may worsen the solder ability.2.Set the peak temperature in 235℃10-20s or 260°C 3-10s.- Cooling1.Ramp down rate 6°C/s max.※Perform adequate test in advance as the reflow temperature profile will vary according to the conditions of the manufacturing process, and the specification of the reflow furnace4 - Hand Soldering ProcessPreheating 150°CTemperature of soldering iron tip 380°C max. 3 to 5 secThe Varistorrs shall be cooled gradually at room ambient temperature5 - Ultrasonic cleaningFor preventing failures or damages. Frequency 29MHz max - radied Power 20W/l max - Period 5mn maxsubjected to a thermal gradient steeper than 3 degrees per second. 2 degrees per second is the ideal gradient. During the soldering process, pre- heating to within 175 degrees of the solders peak temperature is essential to minimize thermal shock.Time (mn)T e m p e r a t u r e (°C )7525Time (mn)T e m p e r a t u r e (°C )2507510012515017520022501:00:002502:00:0003:00:0004:00:00Peak Temp.260°C (3 to 10sec)Preheat.175°C 150sec max.275D-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Würth Elektronik eiSos GmbH & Co.KG - Radialex departmentArtikelnummer / part number :823 50 120 101Bezeichnung :description :0805 ESD SuppressorSMD size:0805D Rollenspezifikation / tape and reel specification :1 - Carrier tape and transparent cover tape should be heat-sealed to carry the products, and the reel should be usedto reel the carrier tape.2 - The adhesion of the heat-sealed cover tape shall be 40 ﹢20/ ﹣15grams.3 - Both the head and the end portion of the taping shall be empty for reel package and SMT auto-pickup machine. And a normal paper tape shall be conected in the head of taping for the operator to handle.(Unit : mm)Spezifikation für Freigabe / specification for releaseKunde / customer:TAPE SPECIFICATION(Unit : mm)Würth Elektronik eiSos GmbH & Co.KG - Radialex departmentD-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Artikelnummer / part number :823 50 120 101Bezeichnung :description :0805 ESD SuppressorSMD size:0805D Rollenspezifikation / tape and reel specification :(Unit : mm)Spezifikation für Freigabe / specification for releaseKunde / customer :REEL DIMENSION(Unit : mm)QUANTITY PER PACKING UNIT Freigabe erteilt /Kunde / customergeneral release:JP. PENLOU Update Clamping Voltage 06-10-15Datum / dateUnterschrift / signature JP. PENLOU High Temperature Load06-07-31Würth ElektronikJP. PENLOU New P/N06-06-02JP. PENLOU Operating temp. Range 05-11-30JP. PENLOULead free soldering 05-11-04Geprüft / checked 2006-07-31Kontrolliert / approved JP. PenlouName Änderung / modificationDatum / dateWürth Elektronik eiSos GmbH & Co.KG - Radialex departmentD-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400。
迪瑞芬豪系列固定卫星通信电话说明书
TranSATRST620The Beam TranSAT Fixed Satellite Telephone provides acomplete hands-free voice and telephone for a wide range ofmobile and fixed site applications where easy access to reliablevoice and data communications is required.The terminal provides a compact fully functioned user handsetand supports both hands-free and privacy modes of operation,automatically switching between either mode with the handsetin or out of the cradle.The system can also be used as a permanent non hands-freesolution simply by not connecting the microphone. The loudring indication through the speaker system makes it an idealinstallation in a noisy environment.The RST620 is equipped with an RS232 serial data port toaccess Iridium data servicesEmergencyVehiclesHeavy TrucksCruise ShipsSmall Aircrafts Handsfree / Privacy ModeVoice/Data/Internet/FAX/SMSCommunication System InegrationEcho Cancellation / Full duplexLatest echo cancellation technology is deployed onTranSAT to enhance handsfree voice quality.Enhanced FeaturesSupport featuressuch as horn alert, radiomute,data connectivity and allow the use of a compactintelligent user handset in privacy mode.11-32V DC Power InputThe DC power input and terminal is capable ofbeing wired to an auxiliary/accessory power supplyas well as constant power.Auxiliary & constant powerThe unit is equipped with intelligent power offfeatures. Whereby the unit will turn off afterminutes when ignition is off. The unit also hasthe option of powering up on accessory power inemergency applications.Voice/Data/Internet/SMS/FaxThe complete range of Iridium data services allowsyou to simply and conveniently gain access toInternet, Email, and corporate LAN.The terminal also supports SMS and the followingIridium Data Services;• Circuit Switched Data• Direct Internet• RUDICS• Short Burst DataPrivate or Handsfree modeHands-free operation allows for quality integrationinto a vehicle/vessel/aircraft with easy access tomaking and receiving calls in a hands-free mode, italso allows the use for privacy mode.Compact Intelligent HandsetThe compact Intelligent Handset provides easyaccess to make and receive calls, access phonebook and SMS as well as switching betweenhandsfree and privacy mode.HandsfreeVoice Data Horn AlertHFISide2RED = +BATT (11 to 32 VDC)BLACK = -BATT (GND)GREEN = ACC PWRHFISide1MicrophoneAntenna1A FusePositive 3A Fuse GroundPOWER SPECIFICATIONSPower input voltage11 - 32 V DC Power Consumption ( AMPS )12 V DC 24 V DC Stand-by - inc handset0.330.14Transmit - inc handset 0.630.23ENVIRONMENT SPECIFICATIONS Temperature Degrees °C Degrees °FOperating Range -15 to +55+5 to +131Storage -30 to +85-22 to +185Humidity 85% non condensing CONNECTORS/INTERFACES Transceiver D25Intelligent Handset RJ45 DPL BUS Data Port RS232 Serial Interface Speaker 3.5mm mono Microphone 2.5mm mono Constant power Screw Connector Auxiliary power Screw Connector Horn Alert Screw Connector Audio MuteScrew ConnectorPHYSICAL SPECIFICATIONS LBT Interface Dimensions - mm 162.4 x 81.6x8183 x 130 x 27Dimensions - inches 38 x 3.16 x 1.17.2 x 5.1 x 1.0Weight - kg 4200.3Weight - lbs9260.66CERTIFICATIONSIEC60945Eelectrical Safety EMC ComplianceHFI - AS/NZ 4601: 1999 - 3.3.4 & 3.3.5Temperature/Humidity/Impact Vibration / Accelerated Aging Independent Aeronautical certification MUST be gained prior to installation.KIT CONTENTSIridium 9522B Transceiver module Main terminal Iridum Intelligent HandsetHandsfree and power InterfaceCable assemblies: DC cables, interface cables Mounting adhesive / velcroData cableUser & Installation manual RST710RST714RST715RST720RST932RST933RST972S RST972RST949Mast Mount Antenna WHIP Antenna (incl 5m cable)Magnetic Mount Antenna (incl 5m cable)Bolt Mount Antenna (incl 5m cable)6m / 19’ Iridium Antenna Cable 12m / 36’ Iridium Antenna Cable 15m extension cable for Intelligent Handset 30m extension cable for Intelligent Handset DPL Aplification cable to increase the headset volume for noisy environments。
5SDA 14F5007 洪流电路芯片产品说明书
Unit V
A
A
mA
A A A2s A2s kW
°C °C
Characteristics
VT0
Threshold voltage
rT
Forward slope resistance
IF = 1000 ÷ 3000 A
VFM
Maximum forward voltage
IFM = 4 000 A
Qrr
Tc = 85 °C
IFRMS
RMS forward current Tc = 85 °C
IRRM
Repetitive reverse current
VR = VRRM
IFSM
Non repetitive peak surge current tp = 8.3 ms
VR = 0 V, half sine pulse
ABB s.r.o., Novodvorska 1768/138a, 142 21 Praha 4, Czech Republic
ABB s.r.o. reserves the right to change the data contained herein at any time without notice
Recovered charge
VR = 100 V, IFM = 2 000 A, diF/dt = -5 A/s
Unless otherwise specified Tj = 160 °C
Value
Unit
min typ max
1.130 V
0.440 m
2.880 V
4 250
µC
Thermal Parameters
欧洲品牌电磁组件型号X12345产品说明书
Dimensions: [mm]Scale - 2,5:17447720101A74477201017447720101T e m p e r a t u r eT T T 7447720101Cautions and Warnings:The following conditions apply to all goods within the product series of WE-TI of Würth Elektronik eiSos GmbH & Co. KG:General:•This electronic component was designed and manufactured for use in general electronic equipment.•Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network, etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury.•Electronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer. •The component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the wire insulation may be damaged or dissolved.•Do not drop or impact the components, the component may be damaged.•Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time.•The customer is responsible for the functionality of their own products. All technical specifications for standard products also apply to customer specific products.Product specific:Soldering:•The solder profile must comply with the technical product specifications. All other profiles will void the warranty.•All other soldering methods are at the customers’ own risk.Cleaning and Washing:•Washing agents used during the production to clean the customer application might damage or change the characteristics of the wire insulation, marking or plating. Washing agents may have a negative effect on the long-term functionality of the product. Potting:•If the product is potted in the costumer application, the potting material might shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the core. Expansion could damage the components. We recommend a manual inspection after potting to avoid these effects. Storage Conditions:• A storage of Würth Elektronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment.•Do not expose the components to direct sunlight.•The storage conditions in the original packaging are defined according to DIN EN 61760-2.•The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components. Packaging:•The packaging specifications apply only to purchase orders comprising whole packaging units. If the ordered quantity exceeds or is lower than the specified packaging unit, packaging in accordance with the packaging specifications cannot be ensured. Handling:•Violation of the technical product specifications such as exceeding the nominal rated current will void the warranty.•Applying currents with audio-frequency signals might result in audible noise due to the magnetostrictive material properties. •Due to heavy weight of the components, strong forces and high accelerations might have the effect to damage the electrical connection or to harm the circuit board and will void the warranty.•Please be aware that products provided in bulk packaging may get bent and might lead to derivations from the mechanical manufacturing tolerances mentioned in our datasheet, which is not considered to be a material defect.•The temperature rise of the component must be taken into consideration. The operating temperature is comprised of ambient temperature and temperature rise of the component.The operating temperature of the component shall not exceed the maximum temperature specified.These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable.However, no responsibility is assumed for inaccuracies or incompleteness.Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODTRi001.0012019-07-17DIN ISO 2768-1mDESCRIPTIONWE-TI Radial Leaded Wire WoundInductor ORDER CODE7447720101SIZE/TYPE BUSINESS UNIT STATUS PAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODTRi001.0012019-07-17DIN ISO 2768-1mDESCRIPTIONWE-TI Radial Leaded Wire WoundInductor ORDER CODE7447720101SIZE/TYPE BUSINESS UNIT STATUS PAGE。
204-10SUGC-S400-A5中文资料
元器件交易网Technical Data Sheet 3.0mm Round Type LED Lamps204-10SUGC/S400-A5█ Features :● ● ● ● ●Choice of various viewing angles Available on tape and reel. Reliable and robust Pb free The product itself will remain within RoHS compliant version.█ Descriptions :●The series is specially designed for applications requiring higher brightness●The led lamps are available with different colors, intensities.█ Applications :● ● ● ●TV set Monitor Telephone ComputerPART NO.204-10SUGC/S400-A5MaterialInGaNEmitted ColorSuper GreenLens ColorWater ClearEVERLIGHT ELECTRONICS CO.,LTD. Device Number : CDLE-020-767http : // Prepared date: 2006/5/13Rev.:2Page: 1 of 6 HuaYing TaoPrepared by:BG0409080,R0402691元器件交易网Technical Data Sheet 3.0mm Round Type LED Lamps204-10SUGC/S400-A5Package DimensionsNotes: 1. All dimensions are in millimetres2. The height of flange must be less than 1.5mm(0.059"). 3. Without special declared,the tolerance is ±0.25mm.█ Absolute Maximum Ratings at Ta = 25℃Parameter Forward Current Operating Temperature Storage Temperature Electrostatic Discharge Soldering Temperature Power Dissipation Reverse Voltage Symbol IF Topr Tstg ESD Tsol Pd VR Rating 30 -40 to +85 -40 to +100 150 260 ± 5 110 5 Unit mA ℃ ℃ V ℃ mW VNote: *1:Soldering time ≦ 5 seconds.EVERLIGHT ELECTRONICS CO.,LTD. Device Number : CDLE-020-767http : // Prepared date: 2006/5/13Rev.:2 Prepared by:Page: 2 of 6 HuaYing Tao元器件交易网Technical Data Sheet 3.0mm Round Type LED Lamps204-10SUGC/S400-A5Electro-Optical Characteristics (Ta=25℃)Parameter Symbol Condition Min. Typ. Max. UnitForward VoltageVFIF=20mA／3.44.0VReverse CurrentIRVR=5V／／50μALuminous IntensityIvIF=20mA16003200／mcdViewing Angle2θ1/2IF=20mA／20／degPeak WavelengthλpIF=20mA／525／nmDominant Wavelength Spectrum Radiation BandwidthλdIF=20mA／530／nm△λIF=20mA／35／nmEVERLIGHT ELECTRONICS CO.,LTD. Device Number : CDLE-020-767http : // Prepared date: 2006/5/13Rev.:2Page: 3 of 6Prepared by: HuaYing Tao元器件交易网Technical Data Sheet 3.0mm Round Type LED Lamps204-10SUGC/S400-A5█Typical Electro-Optical Characteristic Curves:EVERLIGHT ELECTRONICS CO.,LTD. Device Number : CDLE-020-767http : // Prepared date: 2006/5/13Rev.: Prepared by:2Page: 4 of 6 HuaYing Tao元器件交易网Technical Data Sheet 3.0mm Round Type LED Lamps204-10SUGC/S400-A5█Reliability test items and conditions:The reliability of products shall be satisfied with items listed below. Confidence level：97% LTPD：3%NOItemTest ConditionsTest Hours/Cycle 10 SECSample SizeFailure Judgment CriteriaAc/Re1Solder HeatTEMP : 260℃ ± 5 ℃ H : +100℃ 15min ∫ 5 min L : -40℃ 15min H : +100℃ 5min ∫ 10 sec L : -10℃ 5min TEMP : 100℃76 PCS0/12Temperature Cycle300 CYCLES76 PCS0/13Thermal Shock High Temperature Storage Low Temperature Storage DC Operating Life High Temperature / High Humidity300 CYCLES76 PCS Iv≦Ivt*0.5 or Vf≧U or Vf≦L0/141000 HRS76 PCS0/15TEMP : -40℃ TEMP : 25℃ IF = 20mA 85℃ / 85% RH1000 HRS76 PCS0/16 71000 HRS 1000 HRS76 PCS 76 PCS0/1 0/1Note：Ivt：To test Iv value of the chip before the reliablility test Iv：The test value of the chip that has completed the reliablility test U：Upper Specification Limit L： Lower Specification LimitEVERLIGHT ELECTRONICS CO., Device Number : CDLE-020-767http : // Prepared date: 2006/5/13Rev.:2Page: 5 of 6 HuaYing TaoPrepared by:元器件交易网Technical Data Sheet 3.0mm Round Type LED Lamps 204-10SUGC/S400-A5Packing Quantity Specification1.1000PCS/1Bag，4Bags/1Box 2.10Boxes/1CartonLabel Form SpecificationCPN: Customer's Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks 204-10SUGC/S400-A5 HUE: Dominant Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production PlaceNotes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’sconsent.EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\EVERLIGHT ELECTRONICS CO.,LTD. Device Number : CDLE-020-767http : // Prepared date: 2006/5/13Rev.: 2 Prepared by:Page: 6 of 6 HuaYing Tao。
上海致达智利达系统控制有限责任公司
代号 D T B R A P O F S
表3
附加功能 通讯接口 剩余电流保护（接地/漏电） 电压功能 温度保护 4～20mA 模拟量输出 TE 时间保护
电能 失压重起（抗晃电）
故障记录
代号 C L V T A R E D F
●显示方式
表4
显示方式 一体式数码管显示 分体数码管显示，模块尺寸为 72*72，开孔 66*66（单位 mm） 分体数码管显示，模块尺寸为 90*50，开孔 86*49（单位 mm） 分体数码管显示，模块尺寸为 90*70，开孔 86*66（单位 mm）
电动机额定工作电流及额定
6.3A（1.6A-6.3A）2.2KW 25A（6.3A-25A）11KW
采用小型专用电流互感器检测模块
功率
100A（25A-100A）55KW
250A（63A-250A）132KW 800A（250A-800A）250KW
采用外置电流互感器
继电器输出触点，额定负载
阻性负载
安装类别
III 级
2、产品组成
合体式保护器由主体模块（保护控制功能模块）和电流检测模块组成；
分体式保护器由主体模块（保护控制功能模块）、显示模块和电流检测模块组成。
■ 主体模块
一体式主体模块完成测量、显示、保护和控制等功能，通过增加温度、电压、剩余电流、模拟量输
出等功能来完成整个测量与保护功能，通过显示界面来设定参数。
标配功能 √ √ √ √ √ √
√
功能配置 增选功能
√（温度保护） √(漏电)
√（电压功能）
√（增安保护） √(失压重起功能（抗晃电）)
√（选一种）
√（通讯功能） √
上海致达智利达系统控制有限责任公司
湖南三德科技热值分析系列产品说明书
官方微信官方网站目 录SDAC6000(u)量热仪SDACM4000量热仪SDACM3100量热仪SDC712量热仪SDC715量热仪01-05热值分析系列020*********-11元素分析系列SDCHN536碳氢氮元素分析仪SDCH536红外碳氢仪SDH536红外测氢仪SDS350红外定硫仪SDS820自动定硫仪SDS720自动定硫仪SDS-V 定硫仪SDFCl3000自动氟氯分析仪SDFCl1000(a)氟氯分析仪070707080909101111SDTGA8000(a)工业分析仪SDTGA6000工业分析仪SDTGA6000A 工业分析仪SDTGA6000V 工业分析仪SDTGA5000a 工业分析仪SDTGA520(a)水分测试仪SDTGA500光波水分测试仪SDIMF200智能马弗炉SDMF300马弗炉SDIDB413智能干燥箱SDDH315通氮鼓风干燥箱SDDH323鼓风干燥箱SDDH313鼓风干燥箱SDDH306鼓风干燥箱12-22成分分析系列1314151516171819202121222222SDAF105（a /b ）灰熔融性测试仪SDAF4000灰熔融性测试仪SDHG60a 哈氏可磨性指数测定仪23-26物理特性分析系列242526S DUC3150（D ）联合制样机S DHD150t 锤式破碎缩分机S DHC锤式破碎机S DJC颚式破碎机S DRC对辊破碎机S DHCW400×260湿煤破碎机S DPP制样粉碎机S DMD16自动机械缩分器S DNS300环保振筛机S DNS200a标准振筛机S DRD二分器采制样辅助工具30-38样品制备系列313232333334343535353637-38激光盘料仪系列SDLM200便携式激光盘料仪SDLM1250固定式激光盘料仪39-41404142-43公司简介44发展历程45运维服务2829S DVD25风透 式快速除湿干燥系统S DVD3mm 风透 干燥机27-29风透 式低温快速除湿干燥系列热值分析系列适用范围符合标准GB/T213-2008GB/T384-1981 GB/T30727-2014ASTM D5865-2007ISO 1928-2009 JC/T1005-2006《煤的发热量测定方法》《石油产品热值测定法》《固体生物质燃料发热量测定方法》《煤与焦炭总热值的标准试验方法》《固体矿物燃料-氧弹式量热计测定总值并计算净热值》《水泥黑生料发热量测定方法》三德科技是中国第一台自动量热仪(1996年)的发明者，先后自主研发出6代量热仪，缔造了2个“国家重点新产品”。
猎鹰1050气操作诊断膜泵配件包说明书
GENUINE GRACO PARTS AND ACCESSORIESBolt-Through Diaphragm KitsHusky ® 1050 Diaphragm PumpsKit 24B622, Buna-NKits 24B623, 25A858, Geolast ®Kits 24B624, 25A857, TPEKits 24B628, 25A859, 25A863, Santoprene ®Kits 24B629, 25A861,Fluoroelastomer® manual 313435. Save all instructions.Ref.Description Qty.101DIAPHRAGM, material shown at left 2103O-RING, shaft bolt, for 1050A (aluminum), 1050H (hastelloy), and 1050S (stainless steel) models2104TOOL, diaphragm install 1105O-RINGS, manifold, PTFE (not shown)8---ADHESIVE, anaerobic (not shown)1---SEAT (not shown), TPE (25A857), Geo-last (25A858), polypropylene (25A859), Fluoroelastomer (25A861), Santoprene (25A863)4---BALL (not shown), acetal (25A857), Geo-last (25A858), Santoprene (25A859,25A863), Fluoroelastomer (25A861)4Rounded side faces diaphragm.1Apply lithium-based grease.2Torque to 20-25 ft-lb (27-34 N•m) at 100 rpm maximum.3AIR SIDE markings on diaphragm must face center housing.4(Metal Pumps)11033(Plastic Pumps)10112104ti14022a4Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441Original instructions. MM 406807, Rev, D 05/2016Copyright 2009, Graco Inc. is registered to ISO 9001See reverse for assembly instructions.406807DENAssembly1.Follow the steps for your type of pump to assemblethe diaphragms and attach one of the fluid covers. Metal Pumps (1050A, 1050H, 1050S)a.Install the o-ring (102) on the shaft bolt.b.Assemble the fluid side plate, the diaphragm(101), and the air side diaphragm plate on thebolt exactly as shown on page 1.c.Apply medium-strength (blue) Loctite or equiva-lent to the bolt threads. Screw the bolt into theshaft hand tight.d.Grease the shaft u-cups (in center housing) andthe length and ends of the diaphragm shaft.Slide the shaft into the housing.e.Repeat Steps a-c for the other diaphragmassembly.f.Hold one shaft bolt with a wrench and torquethe other bolt to 20-25 ft-lb (27-34 N•m) at 100rpm maximum. Do not over-torque.g.Reattach the first fluid cover (3). See TorqueInstructions in the manual. Go to Step 2. Plastic Pumps (1050C, 1050F, 1050P)a.Assemble the diaphragm (101) and the air sidediaphragm plate onto the fluid side plate.b.Apply medium-strength (blue) Loctite or equiva-lent to the threads of the screw on the fluid sideplate. Screw the assembly into the shafthand-tight.c.Grease the shaft u-cups (in center housing) andthe length and ends of the diaphragm shaft.Slide the shaft into the housing.d.Repeat Steps a and b for the other diaphragmassembly.e.Hold one of the plates with a wrench, andtorque the other plate to 20-25 ft-lb (27-34 N•m)at 100 rpm maximum. Do not over-torque.f.Reattach the first fluid cover. See TorqueInstructions in the manual.2.To ensure proper seating and extend diaphragm life,attach the second fluid cover with air pressure onthe pump.a.Place the supplied tool (104) where the air valvegasket normally goes. Arrows (A) must faceb.Reattach the air valve.c.Supply a minimum of 20 psi (0.14 MPa, 1.4 bar)air pressure to the air valve. Shop air may beused. The diaphragm will shift so the secondfluid cover will seat properly. Keep air pressureon until the second fluid cover is attached.d.Attach the second fluid cover. Follow TorqueInstructions in the manual.e.Remove the air valve and the tool (104). NOTE: If you are replacing the diaphragms but not the air valve, you must remove the air valve and gasket, put the tool in place of the gasket, and put the air valve back on to get the air pressure needed for proper installation of the second fluid cover. Remember to remove the tool and replace the gasket when finished.3.Reassemble the ball check valves and manifolds asexplained in the manual.2406807D。
方向控制功能的D5S方向式座囊式阀门目录说明书
Series D5STechnical Information General DescriptionSeries D5S seat valves are designed for directional control functions. They enable individual hydraulicsolutions for nominal flow up to 800 LPM (211.6 GPM) due to a large variety of poppets, springs and covers, including shuttle valves, stroke limiters, solenoid valves (VV01) and position control.Features• Leak-free seat valve design.• 2- and 3-port bodies.• SAE61 flange.• Numerous pilot options.• 6 poppet types.• 4 sizes (SAE 3/4", 1", 1 1/4", 1 1/2").D5S 2-PortD5S 3-PortSeat Pilot Body Size D5SBodyPilot SleeveSpoolDesign BSeal OptionsSwitching SpringC odeD escription O mit Standard 013 Position Control with ProtectionSolenoid D5S 3-Port3.4 kg (7.5 lbs)4.4 kg (9.7 lbs)5.0 kg (11.0 lbs) 7.8 kg (17.2 lbs)Series D5STechnical InformationSpecificationsD5S Pilot ConfigurationPerformance CurvesD5S 2-Port*D5S 3-Port*Selection of CartridgesD5S 2-Port ExamplesSeat Entry Annular EntryStroke Limiter D5S 2-Port ExamplesSeat Entry Annular EntryD5S 3-Port Examples Stroke Limiter D5S 3-Port ExamplesSeat Entry Annular EntryD5S 2-Port with Solenoid Valve VV01 and Shuttle Valve Examples Seat EntryAnnular EntryD5S 3-Port with Solenoid Valve VV01 and Shuttle Valve ExamplesSeat EntryAnnular EntrySeat Entry Annular EntrySeat Entry Annular EntrySeat Entry Annular EntryDimensions — D5S with VV01Inch equivalents for millimeterPilot oil from X1 to Z Example PIlot Oil External from X1, Pilot Drain Internal Out of B with Vent ValveDimensions — D5S with Position ControlInch equivalents for millimeter dimensions are shown in (**)Example PIlot Oil External from X1, Pilot Drain Internal Out of B with Position ControlX1 = external pilot-oil (optional)Note: Stroke limiter not for use with D5S06, solenoid valve VV01, shuttle valve and position control.D5S Stroke LimiterD5S Stroke Limiter DimensionsD5S with Shuttle Valve DimensionsShuttle valve only in connection with vent valve VV01.Annular EntryPorts Function Port size D5S06D5S08D5S10A Inlet or outlet 3/4" SAE 611" SAE 611-1/4" SAE 61B Outlet or inlet 3/4" SAE 611" SAE 611-1/4" SAE 61X1External pilot port SAE 4Y1External pilot drainSize l1l2l3b1h1h2h3h4d1d20677.0(3.03)101.0(3.98)22.2(0.87)60.0(2.36)37.0(1.46)47.6(1.87)90.0(3.54)127.6(5.02)19.0(0.75)10.5(0.41)0894.0(3.70)120.5(4.74)26.2(1.03)60.0(2.36)45.0(1.77)52.4(2.06)96.0(3.78)133.6(5.26)25.0(0.98)10.5(0.41)1094.0(3.70)128.0(5.04)30.2(1.19)75.0(2.95)48.0(1.89)58.7(2.31)109.0(4.29)146.6(5.77)32.0(1.26)12.5(0.49)2-Port Seal KitsSize Nitrile Fluorocarbon 06S16-91850-0S16-91850-508S16-91851-0S16-91851-510S16-91852-0S16-91852-5Ports FunctionPort sizeD5S06D5S08D5S10D5S12A (2x)Inlet or outlet ¾" SAE 611" SAE 611¼" SAE 611½" SAE 61B Outlet or inlet ¾" SAE 611" SAE 611¼" SAE 611½" SAE 61X1*External pilot port SAE 4Y1External pilot drain MPressure gaugeSize l1l2l3l4b1b2h1h2h3h4h5h6d1t1d2d30649.0(1.93)47.6(1.87)56.0(2.20)63.0(2.48)22.2(0.87)60.0(2.36)41.0(1.61)47.6(1.87)28.0(1.10)22.2(0.87)82.0(3.23)119.0(4.69)3/8" UNC 20.0(0.79)19.0(0.75)10.5(0.41)0855.0(2.17)52.4(2.06)58.0(2.28)65.0(2.56)26.2(1.03)60.0(2.36)47.0(1.85)52.4(2.06)29.0(1.14)26.2(1.03)103.0(4.06)141.0(5.55)3/8" UNC 23.0(0.91)25.0(0.98)10.5(0.41)1057.0(2.24)58.7(2.31)64.0(2.52)61.0(2.40)30.2(1.19)75.0(2.95)65.0(2.56)58.7(2.31)36.0(1.42)30.2(1.19)113.0(4.45)150.0(5.91)7/16" UNC 22.0(0.87)32.0(1.26)12.5(0.49)1237.0(1.46)69.8(2.75)55.0(2.17)93.0(3.66)35.7(1.41)80.0(3.15)73.0(2.87)69.8(2.75)72.0(2.83)35.7(1.41)140.0(5.51)178.0(7.01)1/2" UNC27.0(1.06)38.0(1.50)13.5(0.53)* closed when supplied.。
BDS产品介绍
6
部件套装系列
主控器套装
旧
新
产品说明 特性
包括含中央处理器的主控盒 1 个、电池盒 1 个
旧 （99-LCE75299-S）
新 （99-BSK88999HB）
1. 1 个下载通道，6 个模拟量通道， 1. 1 个下载通道，6 个模拟量通道，
7 个数字量通道，8 个马达通道 7 个数字量通道，8 个马达通道
“第十届中国青少年机器人竞赛”机器人基本技能比赛---机器人范例 “第十届中国青少年机器人竞赛”机器人基本技能比赛---比赛场地
人形系列
I-SOBOT
MRC
ROBOT-X
2
培训套装系列
BDS 初级培训套装
产 品 说 明
特性
包括主控器 1 个、巡线传感器 2 个、减速马达箱 2 个、火焰传感器 1 个、 碰撞开关 1 个、行程开关 1 个、电池盒 1 个、下载线 1 条、基板 2 个、方条 13(2 个)、方条 15(2 个)、方条 17(2 个)、方条 2(15 个)、方条 3(15 个))、 方条 3-A(12 个)、方条 5(12 个)、方条 7(10 个)、扁条 5(4 个)、扁条 7(4 个)、 扁条 9(4 个)、三排扁条 2(2 个)、三排扁条 4(2 个)、三排扁条 7(2 个)、螺丝 1(12 个)、螺丝 15(12 个)、螺丝 2(12 个)、螺丝 25(12 个)、螺丝 3 (6 个)、 螺丝 35(6 个)、螺丝 4(6 个)、螺丝 5(2 个)、螺母 50 个、拐角方条 1(2 个)、 拐角方条 2(2 个)、拐角方条 3(2 个)、钉头轴 4 个、轴 3(3 个)、轴 4(3 个)、 轴 5(4 个)、轴 7(4 个)、轴 9(2 个)、10 齿齿轮 2 个、20 齿齿轮 2 个、30 齿 齿轮 2 个、40 齿齿轮 2 个、50 齿齿轮 2 个、差速器 1 个、20 齿冠齿轮 1 个、 20 齿伞齿轮 3 个、20 齿斜齿轮 1 个、30 齿斜齿轮 1 个、齿条 2 个、齿条压板 2 个、蜗杆 1 个、半轴套 15 个、轴套 12 个、联轴套 2 个、直角轴套 1(2 个)、 直角套 2(2 个)、直角轴套 3(2 个)、拐角轴套 1(2 个)、拐角轴套 2(2 个)、拐 角轴套 3(2 个)、拐角轴套 4(2 个)、拐角轴套 5(2 个)、内接头 1 个、轴座 1 个、拖轮座 1 个、定轴板 1 个、辅助轮架 1 个、胶介 48 个、线固定件 10 个、 小车轮 1 个、大车轮 2 个等共 367 个零件，并送光碟 1 张、工具 1 套，赠送配 件包 1 包