割草机的使用方法及注意事项外文文献翻译、中英文翻译

XXX
设计(XX)外文资料翻译
院系
专业
学生姓名
班级学号
外文出处WORD MODEL XSZ56
LAWN MOWER
附件：1.外文资料翻译译文（约3000汉字）；
2.外文资料原文(与课题相关的1万印刷符号左右)。

目录
第1节：检验铭牌 (1)
第2节：售后服务 (1)
第3节：倾斜范围 (1)
第4节：重要的安全操作规则 (1)
第5节：拆箱说明 (4)
第6节：装配说明 (4)
第7节：控制部件 (5)
第8节：操作 (6)
第9节：调节校准 (7)
第10节：维修包养 (8)
第1节：检验铭牌
这本操作者手册使用手册是你操作机器的重要部分。

它会帮助你在使用时的装配、筹备和维修工作。

请务必仔细阅读。

在你第一次使用机器之前，请从这本手册上确定机器的铭牌的位置和相关信息。

如果你从供应商或WORD售后服务部门请求帮助时，这些相关信息非常重要。

●每台机器都有一个机器铭牌。

你只要站在操作位置的后面然后往下看就能发现
这个机器铭牌
第2节：售后服务
●确定你的MODEL NUMBER和SERIAL NUMBER---查找机器各部分具体的
MODEL NUMBER和SERIAL NUMBER，参考第一节。

●如果你在装配过程中有困难，或者注意到在机器的控制、操作和保养方面有问
题，请与供销商联系。

●在联系时确定好你的MODEL NUMBER和SERIAL NUMBER。

●这两个数字很重要，在与供销商联系时会被要求登记这组编号。

第3节：倾斜范围
警告
剪割斜度不要超过规定的斜度（每10英尺大约上升2～1/2英尺）。

如果一个剪草机操作者操作时达到这个角度，那么你将会很难继续前进，并且可能跌倒，受到很严重的伤害。

操作剪草机时请不要超过这个倾斜度。

第4节：重要的安全操作规则
注意：此标志指明一些重要的安全指令，如不遵循，可能危及到个人安全，自身
及其他人的财产。

在操作割草机之前通读并遵循这本手册中的指令。

错误的操作会导致个人损伤。

看到这种标志时请留意！
危险：操作割草机时必须按照手册上的安全操作措施的规定。

当接通电源时，任
何的粗心大意或过失都会导致不同的伤害。

这种机器有绞断手脚和卷带物体的危险。

如不严格的遵循以下安全指示，会导致伤亡。

1.普通操作
●在装配机器之前仔细全面的阅读顾客指南。

在操作前通读并完全遵循机器及手
册上的指示，要熟悉机器的控制及用途。

将手册妥善放置，整理参考书并保存替换零部件。

●旋转中的割草机是精密的动力设备，不是玩具。

因此，应付出百分之百的注意
力。

该机器只是设计用来割草的，请不要用作其他方面。

●不满14岁的儿童禁止使用运作中的割草机。

满14岁和大于14岁的儿童也必
须在家人的旁指和监督下才能使用。

只有对这些安全措施熟悉，有责任心的人
才能允许使用该机器。

●确保所有人的工作范围内无杂物，特别是小孩和宠物。

如有发现，关闭发动机
以防刀片伤人和飞物伤人。

尽管很仔细彻底地清除了异物，但总会漏看一两个东西，会被机器从任何方向甩出，造成操作者及工作区域中的人身伤害。

●彻底检查机器的工作区域。

清除所有的石头，树枝，电线，骨头，玩具及其他
又肯被机器甩出造成危害的异物。

规范割草模式，以免异物砸伤，保持儿童，旁观者及辅助者远离工作中的割草机75步以外。

●在操作或检修机器时要配戴安全眼睛或护目镜，保护眼睛不受飞物的伤害。

●穿戴结实的防滑工作鞋以及贴身舒适的便裤和上衣。

裤子和上衣要将腿和胳膊
包起来，推荐使用钢制斜钉的工作鞋，禁止穿宽松的衣服，挂带首饰以防在行动中被扯住。

禁止在工作中赤脚，穿凉鞋，穿易滑的鞋和轻巧的鞋（如网球鞋）●不要将手和脚靠近机器旋转的部分。

保持草屑通道不堵塞以防旋转的刀片造成
伤害。

●很多事故时由于割草机倾斜压在脚上造成的。

当倾斜时，不要再紧握，立即放
开手把。

●前行时不可将机器拖向自己，如果必须将机器从墙或堵塞物前拉回，首先向后
及地面看看，然后按一下步骤进行：
●向后退至胳膊足以展伸开的位置。

●确信此时保持平衡步履正常。

2.斜坡操作
为了你的安全，使用手册中的斜度测量仪器测量工作地，如斜坡或山陵。

工作所在地的斜坡度不得超过15°的斜坡上修理草坪。

●在坡地上割草时千万不要使机器一起一伏，在改变方向时必须集中注意
力。

●注意洞穴、凹沟、隐藏物或隆起的地。

茂盛的草丛里往往隐藏着意想不到
的东西。

●注意脚步，跌倒或摔跤会引起人身伤害。

当觉得自己失去平衡时，松掉刀
片以控制手柄，不到三秒钟刀片就会停止转动。

不应该做的：
●禁止在坡地、沟渠、筑堤附近割草，修理草坪，以防止操作者失去平衡。

●禁止在超过15°的斜坡上修理草坪。

●禁止在潮湿的地上割草，以防滑倒。

3.儿童须知
如果操作者不注意在场的儿童的话，很可能发生悲剧性的事故。

割草机及割草的过程往往对儿童有很大的吸引力。

不要想当然的认为他们会乖乖的站在他们该待的地方。

●让儿童待在修建范围之外，并且要有一个有责任的成年人照顾。

●保持警惕，假如儿童跑进工作区域，关掉机器。

●在后退之前观察身后的人或物。

4.服务
●使用汽油和其他燃料时要小心，它们都是易燃物并且蒸汽易爆炸。

●使用一种经批准合格的汽油容器。

●机器运转时不得打开燃气盖，补充汽油，在引擎熄火后两分钟后才能补充燃料。

●在启动前要小心打开燃器盖，擦干溢出的汽油，以防自燃或爆炸。

●熄灭所有的香烟、雪茄、烟斗等一切火源。

●不要在室内补充燃料，自燃蒸汽会积聚在室内。

●不能将机器和油箱放在屋里，因为屋里有明火，例如煤气加热器、小型取暖器
和火炉。

●不允许在封闭区域内启动引擎。

●为了防止火灾，使机器不接触干草、枯叶、垃圾草，清除溢出的汽油和燃料，
机器至少降温5分钟才能入库。

●在清洗、检验、修理之前，确定刀片和能动的部件已经停止不动了，断开火花
塞，并且断开电线以防机器突然启动。

警告：机器排除的尾气含有有害化学成分，据加利福尼亚州报道，曾引起癌症，先天不足或其他生殖危害。

警告—你的责任：务必保证操作本机器着详细阅读并遵守手册上和机器上的安全说明。

第5节：拆箱说明
把机器从纸箱中取出
●启开钉子，撬开顶部粘接处，或掘开箱子尾部的塞子，然后揭开顶部，打开箱
子。

●移开和机器相关的零散部件。

●沿虚线拆开箱子，并保持平放。

●移开拆箱工具。

●使机器小心从箱子中滚动或滑动出来。

仔细检查纸箱中的零散部件。

第6节：装配说明
装配条款
●一把钳子（不是必需，但很有用）
●润滑油
●纯净汽油
重要：机器在装运过程中没有装汽油和润滑油。

保证在你使用机器前，按照各部分说明把机器的相应部分加汽油或润滑油。

注意：多次从操作位置观测，左右对比参照
组装剪草机
请按步骤1-9来组装机器：
第一步：拿起装草屑的袋子，放在一边
第二步：提起上面的手柄，使它与下面的柄成一条线。

第三步：旋转两侧的螺母。

第四步：完全抬起装配好的手柄，确保不要被钢丝绳缠住。

第五步：用钳子把下面的柄拧紧在固定托架上。

第六步：把下面的柄与托架用两侧螺母，放松螺母和螺栓连接起来，旋紧螺母。

第七步：把控制钢丝用柄处的拉绳系在手柄上。

第八步：把切割控制手柄压紧在上手柄处，然后慢慢移开发动机绳索。

第九步：把发动机绳索系在绳索控制环中。

第7节：控制部件
切割控制手柄
切割控制手柄在割草机的主手柄上，如图5。

开始操作机器时必须压低切割控制手柄。

停止切割时请松开切割控制手柄。

警告：切割控制手柄是一个安全装置。

不要忽视它的作用。

当机器运转时切割就
会运转。

减速器
减速器与发动机相连，用来控制机器的速率排挡。

警告：减速器不能停止机器。

不要在机器运行时调整减速器。

反冲控制器
反冲控制器手柄在下部手柄处，如图5.请站在启动机器位置的后面。

驱动离合器控制手柄
驱动时紧握驱动离合器控制手柄，停止驱动时松开驱动离合器控制手柄。

当越过障碍物要减速，或启动停止时松开驱动离合器控制手柄。

切割高度控制手柄
注意：在出厂时剪草机的剪草高度调到最低位置。

请根据需要调整高度。

切割高
度控制杆连在旋转轮盘的尾部。

调整切割高度时，先拔出操纵杆，然后向前或向后拨来新的切割高度。

见图6。

注意：在不平坦的草地上，请调到高一点的切割位置，以防连根切除。

发动机控制
请参阅发动机手册或发动机上标明的控制功能。

第8节：操作
警告：保持手脚远离切割层的斜槽处。

如图2。

操作任何割草机都有可能导致外
来物飞入眼睛，以致眼睛受伤。

请佩带眼镜或护目镜。

注意：请根据你的草坪的情况选择最适合的切割高度。

请参阅控制器章节中切割高度校正杆。

注入汽油或润滑油
请根据发动机说明给发动机注入汽油或润滑油。

仔细阅读说明。

警告：请不要在机器运行时或停下后至少冷却两分钟后注入汽油。

每次启动割草机
所有装置：
●把火花塞引线系在火花塞上。

确保火花塞引线尾部的金属帽牢系在火花塞的金
属顶端上。

●根据中间校正测试选择合适的驱动离合器操作。

中间校正测试
作中间校正测试前请先回答以下问题：
●当松开驱动离合器时，把机器推向前面或拉到后面，它的移动容易吗？
●紧握驱动离合控制器，然后向后拉机器，旋转轮盘锁了吗（不动）？
●驱动离合控制器的钢丝绳缠的松还是紧？
如果你3个问题的答案都是“是”，你的割草机通过测试，你可以使用割草机了。

如果你3个问题中有任何一个答案是“否”，你要根据驱动离合器校正说明来调整你的驱动离合控制器。

启动
●把减速器调到快挡。

●按照发动机说明的指示为发动机加满油。

●站在机器后面，把切割控制手柄紧握在上面的手柄上。

停机
停机时只要松开切割控制手柄紧。

警告：发动机停止后切割还要持续几分钟。

使用割草机
确保草坪上不要有石子、枯枝、金属丝或其他能损坏机器的杂物。

这些东西可能会被机器甩出至任何位置，会对操作者或其他人造成意外伤害。

最好不要修剪潮湿的草坪，它会阻塞机器底部，阻碍草屑排出，导致你跌倒。

新长出的、浓密的，或潮湿的草坪需要更精细的修剪。

一个优质的草坪，剪切量不要超过总高度的三分之一。

在秋季，只有它生长的时候才需修剪。

警告：如果遇到异物，关闭发动机，移开火花塞引线，仔细检查，在再次启动前
排除故障。

机器的大幅振动是故障的迹象，要立刻检查维修。

草屑袋
机器可以盛装草屑。

按步骤1、2来准备。

第1步，打开滑槽口。

第2步，把袋子装入接头中。

清空草屑袋
把靠在手柄下部和底部的草屑袋撑开，滑槽口处的绳子解开。

把袋子拆下来。

如图9所示。

拾起草屑袋尾部手柄，袋子就可以打开，排除草屑。

见图7。

当重新装上袋子时，确保袋子顶部把手间的撑架撑开。

尾部排草屑
割草机可以尾部排草屑。

按步骤1、2所示。

第1步：提升滑槽口/
第2步：用螺钉和螺母把排泄槽安装上。

第9节：调节校准
警告：在没有停止发动机和断开火花塞电线的情况下，禁止对割草机进行调节。

手柄调节高度
割草机提供三种手柄高度，原装的手柄位于中间位置。

按以下步骤调节高度：
●去除启动装置的绳索。

●松开手动调节器和车身的螺栓。

●移动手柄向上或向下调节高度，如图8。

●固定手柄：旋紧调节杆和螺栓以及放松螺栓。

●装回启动装置的绳索，按初装时的指示。

第10节：维修包养
警告：在修理和做任何保养前必须断开火花塞电线且接地。

注意：当倾斜机器时，放空油箱中的油并把火花塞放在一边。

不能将机器倾斜超
过90°并且不能使它长时间处于倾斜状态。

油料会流进发动机的上部，出现启动问题。

发动机
参阅不同引擎手册获得保养发动机的说明指示。

●按照随机附带手册指示保持发动机润滑，阅读并理解。

●在正常情况下，每25小时为空气清洁机提供保养。

在环境恶劣的条件下每几
小时就要进行清理。

发动机无力或太有力都表明空气清洁机需要清理。

参阅手册进行保养。

●每个季度火花塞要进行清洗，火花隙要重置。

推荐在每个割草季前替换火花塞。

检查引擎手册取得正确的型号及火花隙规格。

●定期用布或刷子擦洗发动机。

保持制冷装置干净并能提供适当的气流循环，对
于发达机工作和寿命都有好处。

确保消声器处草屑、污物和易燃垃圾。

底座
底座下表面在每次使用之后都要进行清洗以防碎草、叶子、污物或其他一些东西凝在一块儿。

若这些垃圾聚在一块，会导致生锈和腐蚀，并且妨碍覆盖、输送或装袋。

底板可以倾斜割草机来清洗，碎屑的清晰需要一种套配的工具（确保火花塞电线断开）。

切割刀的移动、更换和打磨
●当移动刀片重磨或更换时，戴厚手套或用破衣服包住刀片以防伤手。

●把刀片和刀片接头连在电机曲轴上的螺栓和刀片支架移开。

●将刀片和支架从曲轴上移开。

警告：定期的检查刀片转接头以防破裂，特别是控制异物时，必需时更换。

当磨刀的时候，按原始角度磨刀。

非常重要的是每一个刀口都要均匀地磨。

不均匀地磨刀会造成平衡测试。

将刀片安上刀头时，润滑发动机曲轴，用轻质油润滑刀片内表面。

●确保安装刀片时将刀片上有标记的一面向地。

●将电机曲轴与刀片嵌合。

●将刀头安装在接头上，确保刀头是校正过的并且与法兰盘相连接。

●将刀片外架装上，并确保也是校正过的。

●更换六角螺栓。

●紧固螺栓使应力达到450～600Ibs.max
注意：确保割草机安全操作，刀架螺栓必须定期检查是否达到应力要求。

皮带的移动及更换
第1步：断开火花塞电线且接地。

第2步：排空油箱或在油缸盖下一片塑料防油泄漏。

第3步：松开两颗六角螺栓，揭开皮带防护盖。

第4步：松开束带螺栓。

第5步：调节后面顶部的调节器至第六档。

第6步：朝一边倾斜机器。

第7步：去除固定皮带轮防护盖与底座的螺栓。

第8步：去除皮带防护盖。

第9步：将旧皮带卸下。

第10步：换上新皮带。

第11步：将皮带绕过传动装置，旋转防护盖使皮带进入轮槽。

第12步：紧固束带螺栓。

第13步：将防护盖安装回原来的位置，并旋上六角螺栓。

第14步：将机器放正，装回上盖并旋上螺栓。

重点：换皮带的时候不要拆开刀片与刀头。

CONTENTS
SECTION 1：FINDING YOUR MODEL NUMBER (1)
SECTION 2：CALLING CUSTOMER SUPPORT (1)
SECTION 3：SLOPE GAUGE (1)
SECTION 4：IMPORTANT SAFE OPERA TION PRACICES (1)
SECTION 5：UNPACKING INS TRUCTIONS (4)
SECTION 6：SET-UP INSTR UCTIONS (4)
SECTION 7：CONTROLS (5)
SECTION 8：OPERA TION (6)
SECTION 9：ADJUSTMENTS (7)
SECTION 10：MAINTENANCE (8)
Sorry to no longer advising if any changing to improve the function. SECTION 1：FINDING YOUR MODEL NUMBER
This Operator’s Manual is an important part of your new walk behind. It will help you assemble, prepare and maintain your walk behind. Please read and understand what it says.
Before you start to prepare your walk behind for its first use, please locate the model plate and copy the information form it in this Operator’s Manual. The information on the model plate is very important if you need help from your dealer or the WORD customer support department.
●Every walk behind has a model plate. You can locate it by standing behind the unit
in the operating position and looking down at the rear of the deck.
SECTION 2：CALLING CUSTOMER SUPPORT
●LOCATE YOUR MODEL NUMBERAND SERIAL NUMBER—Record this
information in the space provided. To find your unit’s specific model number and serial number, see SECTION 1: FINDING YOUR MODEL NUMBER.
●If you are having difficulty assembling this product or if you have any questions
regarding the controls, operation or maintenance of this unit, please call the dealer.
●Please have your model number and serial number ready when you call.
●Although both numbers are important, you will be asked to enter only your serial
number before you call can be processed.
SECTION 3：SLOPE GAUGE
WARNING
Do not mow on inclines with a slope in excess of degrees (arise of approximately 2-1/2 feet every 10 feet). If operating a walk-behind mower on such a slope, it is extremely difficult to maintain your footing and you could slip, resulting in serious injury. Operate WALK-BEHIND mowers across the face of slopes, never up and slpoes. SECTION 4：IMPORTANT SAFE OPERATION PRACICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PREPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEIMPTING TO OPERATE YOUR LAWN MOWER. FAILURE TO COMPL Y WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL, HEED ITS WARNING.
DANGER: Your lawn mower was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of operator can result in serious injury. This lawn mower is capable of
amputating hands and feet and throwing objects. Failure to observe the safety instructions could result in serious injury or death.
5.GENERAL OPERATION
●Read this owner’s guide carefully in its entirety before attempting to assemble this
machine. Read understand and follow all instructions on the machine and in the manuals before operation. Be completely familiar with the controls and the proper use of this machine before operating it. Keep this manual in a safe place foe future and regular reference and foe ordering replacement parts.
●Your rotary mower is a precision piece of power equipment, not a plaything.
Therefore, exercise extreme caution at times. Your unit has been designed to perform one job: to mow grass. Do not use it for any other purpose.
●Never allow children under 14 year old to operate a power mower. Children 14
years old and over should only operate mower under close parental supervision.
Only responsible individuals who are familiar with these rules of safe operation should be allowed to use your mower.
●Keep the area of operation clear of all persons, particularly small children and pets.
Stop engine when they are in the vicinity of our mower to help prevent blade contact or thrown object injury. Although the area of operation should be completely cleared of foreign objects, an object may have been overlooked and could be accidentally thrown by the mower in any direction and cause serious personal injury to the operator or any others allowed in the area.
●Thoroughly inspect the area where the equipment is to be used. Remove all stones,
sticks, wire, bones, toys and other foreign objects which could be picked up and thrown by the mower in any direction and cause serious personal injury to the operator or any others allowed in the area. Plan your mowing pattern to avoid discharge of material toward roads, sidewalks, bystanders and the like. To help avoid a thrown objects injury, keep children, by standers and helps at least 75 feet from the mower while it is in operation.
●Always wear safety glasses or safety goggles during operation or while performing
an adjustment or repair, to protect eyes from foreign objects that may be thrown from the machine in any direction.
●Wear sturdy, rough-soled work shoes and close-fitting slacks and shirts. Shirts and
pants that cover the arms and legs and steel-toed shoes are recommended. Do not wear loose fitting clothes or jewelry. They can be caught in moving parts. Never operate a unit in bare feet, sandals, slippery or light weight (e.g. canvas) shoes.
●Do not put hands or feet near or under rotating parts. Keep clear of discharge
opening at all times as the rotating blade can cause injury.
●Many injuries occur as a result of the mower being pulled over the foot during a
fall. Do not hang on to the mower if you are falling; release the handle immediately.
●Never pull the mower toward you while you are walking. If you must back the
mower away from a wall or obstruction first look down and behind, and then follow these steps.
●Step back from the mower to fully extend your arms.
●Be sure you are well balanced with sure footing.
6.SLOPE OPERATION
For your safety, use the slope gauge included as part of this manual to measure slope before operating this unit on a sloped or hilly area. If the slope is greater than 15 degrees as shown on the slope gauge, do not operate this unit on that area or serious injury could result.
●Mow across the face of slopes, never up and down. Exercise extreme caution when
changing direction on slopes.
●Watch for holes, ruts, hidden objects, or bumps. Tall grass can hide obstacles.
●Always be sure of your footing. A slip and fall can cause serious personal injury. If
you feel you are losing your balance release the blade control handle immediately and the blade will stop in less than 3 seconds.
DO NOT:
●Do not mow near drop-offs, ditches or embankments. The operator could lose
footing or balance.
●Do not mow slope greater than 15 degrees as shown on the slope gauge.
●Do not mow on wet grass. Reduced footing could cause gauge.
7.CHILDREN
Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the mower and the mowing activity. Never assume that children will remain where you last saw them.
●Keep children out of the mowing area and under the watchful care of a
responsible adult other than the operator.
●Be alert and turn mower off if a child enters the area.
●Before and while moving backwards, look behind and down for small children
or other objects.
8.SERVICE
●Use extreme care in handing gasoline and other fuels. They are extremely
flammable and the vapors are explosive.
●Use only an approved gasoline container.
●Never remove gas cap or add fuel while the engine is running. Allow engine
to cool at least two minutes before refueling.
●Replace gasoline cap securely and wipe off any spilled gasoline before
starting the engine as it may cause a fire or explosion.
●Extinguish all cigarettes, cigars, pipes and other sources of ignition.
●Never refuel machine indoors because flammable vapors will accumulate in
the area.
●Never store the machine or fuel container inside where is an open flame or
spark such as a gas water heater, space heater, or furnace.
●Never run an engine inside a closed area.
●To reduce fire hazard, keep mower free of grass, leaves, or other debris
build-up. Clean up oil or fuel spillage. Allow mower to cool at least 5 minutes
before storing.
●Before cleaning, repairing, or inspecting, make certain the blade and all
moving parts have stopped. Disconnect the spark plug wire, and keep the wire
away from the spark plug to prevent accidental starting.
SECTION 5：UNPACKING INS TRUCTIONS
REMOVE UNIT FROM CARTOM
●Remove staples, break glue on top flaps, or cut tape at carton end and peel along
top flap to open carton.
●Remove loose parts if included with unit.
●Cut along dotted lines and lay carton down flat.
●Remove packing material.
●Roll or slide unit out of carton. Check carton thoroughly for loose parts.
SECTION 6：SET-UP INSTR UCTIONS
ITEMS REQUIRED FOR ASSEMBLY
●Pair of pliers (Not necessary, but helpful)
●Motor Oil
●Fresh Gasoline
IMPO RTANT: This unit is shipped WITHOUT GASOLINE or OIL in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your mower.
NOTE: Reference to right or left hand side of the mower is observed from the operation position.
SET UP YOUR LAWN MOWER
Follow steps 1 through 9 to set up your lawn
Step1: remove grass bag from unit and set it out of the way.
Step2: Life upper handle. Align it with lower handle.
Step3: Tighten wing nuts.
Step4: Raise complete handle assembly. Make sure not to kink the control cables.
Step5: Pinch lower handle against mounting bracket with pliers.
Step6: Connect lower handle and mounting bracket with nuts, locknut and bolt.
Step7: Attack control cables to handle with pull ties found on the handle.
Step8: Squeeze the blade control against the upper handle and pull out the starter rope slowly.
Step9: Thread the starter rope into the rope guide.
SECTION 7：CONTROLS
BLADE CONTROL HANDLE
The blade control handle is located on the handle of the mower. See Figure 5. The blade control handle must be depressed in order to start and operate the unit. Release the blade control handle to stop the engine and blade.
WARNING: The blade control handle is a safety device. Never attempt to bypass its operations. The blade will be rotating whenever the engine is running.
THROTTLE
The throttle is located on the engine. It is used to regulate the engine speed. WARNING:The throttle control cannot be used to stop the engine. Do not adjust the throttle control with the engine running.
RECOIL STARTER
The recoil starter handle is attached to the lower handle. See Figure 5. Stand behind the unit in the operating position to start the unit.
DRIVVE CLUTCH CONTROL
Squeeze the drive clutch control to engage the drive system. Release the clutch control to disengage the drive system. Release the clutch control to slow down when negotiating an obstacle, making a turn or stopping.
CUTTING HEIGHT ADUJSTMENT LEVER
NOTE: Your mower is shipped with the cutting height in the lowest position. Sdjust the cutting height as follows.
The cutting height adjustment lever is located above the right rear wheel. To adjust the cutting height, pull the lever out and away from the mower and then move it forward or backward to select a new cutting height.
ENGINE CONTROLS
See the engine manual for the location and function of the controls located on the engine.
SECTION 8：OPERATION
WARNING: Keep hands and feet away from the chute area on the cutting deck. See figures 2. The operation of any lawn mower can result in foreign objects being thrown into the eyes, which can result in sever eye damage. Always wear safety glasses or eye shields.
NOTE: For best results raise the cutting position until it is determined which height is best for your lawn. See CUTTING HEIGHT ADJUSTMENT LEVER in the CONTROLS section.
GAS AND OIL FILL-UP
Service the engine with gasoline and oil as instructed in the separate engine manual. Read all instruction carefully.
WARNING: Never fill fuel tank indoors with engine running or until the engine has been allowed to cool for at least two minutes after running.
EACH TIME YOU START YOUR MOWER
ALL UNITS:
●Attach spark plug wire to spark plug. Make certain the metal cap on the end of the
spark plug wire is fastened securely over the metal tip on the spark plug.
●Check for proper drive clutch operation using the NEUTRAL ADJUSTMENT
TEST.
NEUTRAL ADJUSTMENT TEST
To perform the NEUTRAL ADJUSTMENT TEST answer the following questions.
●With the drive clutch control release, push mower forward and pull it backward.
Does it move freely?
●Squeeze the drive clutch control and pull the mover backward. Do the rear wheels
lock (not turn)?
●Is the drive clutch control cable free of kinks or sharp bends?
If you answered “yes” to all three questions, your mower passed the test and can start your mower.
If you answered “no” to any of the three questions, you will have to adjust the drive clutch control following instructions in the DRIVE CLUTCH CONTROL ADJUSTMENT section.
TO START ENGINE AND ENGAGE BLADE
●Move the throttle control on the engine to the fast (rabbit) position.
●Prime engine is instructed in the separate engine manual.
●Stand behind the unit, squeeze the blade control handle and hold it against the
upper handle.
NOTE: If any problems are encountered, refer to the TROUBLE SHOOTING section of this manual.
TO STOP ENGINE AND BLADE
Release the blade control handle to stop the engine and the blade.
WARNING: The blade continues to rotate for a few seconds the engine is shut off. USING YOUR ROTARY MOWER
Be sure that the lawn is clear of stones, sticks, wire, or other objects which could damage the lawn mower or the engine. Such objects could be accidently thrown by the mower in any direction and cause serious personal injury to the operator and others. For best results, do not cut wet grass clippings, and could cause you to slip and fall. New grass, thick grass or wet grass may require a narrower cut.
For a healthier lawn, never cut off more than one-third of the total length of the grass. Your lawn should be cut in the fall as long as there is growth.
This mower is designed to be operated at full throttle to give you the best cut and do the most effective job of mowing or mulching.
WARNING: If you strike a foreign object, stop the engine. Remove wire from the
spark plug, thoroughly inspect the mower for any damage, and repair the damage before restarting and operating the mower. Extensive vibration of the mower during operation is an indication of damage. The unit should be promptly inspected and repaired.
BAGGING GRASS CLIPPINGS
This mower can bag grass clippings. Follow steps 1 and steps 2 to ready the mower for bagging.
Step1. Lift chute door.
Step2. Slide bag onto adapter.。