您的位置：360文档中心› 模具图中常见英文词语

模具图中常见英文词语

合集下载

(完整版)模具专业英文术语大全

(完整版)模具专业英文术语大全

模具英语专业术语模具述语一、入水：gate进入位： gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口： switching runner/gate唧嘴口径： sprue diameter二、流道: runner热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴： hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头： connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件： mold components 三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin顶针板：ejector retainner plate托板： support plate螺丝： screw管钉：dowel pin 开模槽：ply bar scot内模管位：core/cavity inter-lock顶针： ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cuton B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length 稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft 滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate 动模座板 moving clamp plate. bottom clamping plate. bottom plate上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate 垫块 spacer parallel支架 ejector housing. mould base leg 压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材 khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance 绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage针pin 物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity 接触长度contact length接触件电镀层contact plating 接触压力contact pressure 接触件中心距contact space 接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ，Ribbon cable柔性印刷电线Flexible printed wiring多层印制电路Multilayer printed circuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board，Double-sided board表面安装surface Mounting翘曲warp， bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plate A板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush 直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force 锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core 螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板11 / 17Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具标准翻译。

模具常用术语中英文对照

模具常用术语中英文对照

富达金实业"Fudakin Insdustrial Co.,Ltd"模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料井Cold Slag /collect slag线切割Wire E.D.M轮廓，外廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针,垃圾钉 Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft落单会议Kick-Off Meeting装卸孔Handling Hole运输安全带Mold strap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap导柱位Leader Pin Location 耐落胶Teflon Paste偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hot nozzle火花机 E.D.M熔接线Weld line压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar下模水口铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin 顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹） Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven 走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板 A'plateB板 B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计简图Design Preliminary 丝印Silk print不干胶Adhesive Sticker 导向针Guide Din公差Tolerance 线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt 盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High Volume Running Mold 剖面图Cross Section模具结构Mold Construction模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension雕刻Engrave托司 EJ.GUIDE PIN料花 Silver。

模具英语术语

模具英语术语

die模具figure file, chart file 图档cutting die, blanking die 冲裁模progressive die, follow (-on)die 连续模compound die 复合模punched hole 冲孔panel board 镶块to cutedges=side cut=side scrap 切边to bending 折弯to pull, to stretch 拉伸Line streching, line pulling 线拉伸engraving, to engrave 刻印upsiding down edges 翻羽边to stake 铆合design modification 设计变化die block 模块folded block 折弯块sliding block 滑块location pin 定位销lifting pin 顶料销die plate, front board 模板padding block 垫块stepping bar 垫条upper die base 上模座lower die base 下模座upper supporting blank 上承板upper padding plate blank 上垫板spare dies模具备品spring弹簧bolt螺栓plate电镀mold成型material for engineering mold testing 工程试模材料not included in physical inventory 不歹^入盘点incoming material to be inspected 进货待验PCE assembly production schedule sheetPCE组装厂生产排配表model机锤work order 工令revision 版次production control confirmation 生产确认checked by 初审approved by 核准stock age analysis sheet库存货龄分析表on-hand inventory 现有库存available material 良品可使用obsolete material 良品已呆滞to be inspected or reworked待验或重工cause description 原因说明part number/ P/N 料号item/group/class 类另ijprepared by 制表year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory 盘点数量physical count quantity 帐面数量difference quantity 差异量good product/accepted goods/ accepted parts/good parts 良品defective product/non-good parts 不良品disposed goods 处理品on way location 在途仓oversea location 海夕卜仓spare parts physical inventory list 备品盘点清单spare molds location 模具备品仓skid/pallet 栈板tox machine 自铆机wire EDM 线割EDM放电机coil stock 卷料sheet stock 片料tolerance 工差score=groove 压线cam block 滑块pilot导正筒trim剪外边pierce剪内边drag form 压锻差pocket for the punch head 挂钩槽slug hole废料孔feature die 公母模expansion dwg 展开图shim(wedge)楔子torch-flame cut 火焰切割set screw 止付螺丝form block 折刀stop pin定位销round pierce punch=die button 圆冲子shape punch=die insert 异形子stock locater block 定位块under cut=scrap chopper 清角active plate 活动板baffle plate 挡块cover plate 盖板male die 公模female die 母模groove punch 压线冲子air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板bushing block 衬套insert入块capability 能力parameter 参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping 脱脂main manifold 主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization 去磁;消磁high-speed transmission 高速传递heat dissipation 热传rack上料degrease 脱脂rinse水洗alkaline etch 龄咬desmut剥黑膜D.I. rinse纯水次Chromate铭酸处理Anodize阳性处理seal封孔revision 版次part number/P/N 料号good products 良品scraped products 报放心品defective products 不良品finished products 成品disposed products 处理品barcode 条码flow chart流程表单stamping 冲压molding 成型spare parts=buffer 备品coordinate 座标dismantle the die 折模auxiliary fuction 辅助功能poly-line多义线heater band 力口热片thermocouple 热电偶sand blasting 喷沙grit砂砾derusting machine 除锈机degate 打浇口dryer烘干机induction 感应induction light 感应光response=reaction=interaction 感应ram连杆edge finder 巡边器concave 凸convex 凹short射料不足nick 缺口speck瑕疵shine亮班splay银纹gas mark 焦痕delamination 起鳞cold slug 冷块blush导色gouge沟槽;凿槽satin texture段面咬花witness line 证示线patent专利grit沙砾granule=peuet=grain 2细粒grit maker抽粒机cushion 缓冲magnalium镁铝合金magnesium 镁金metal plate 钣金lathe 车mill 锉plane 刨grind 磨drill 铝boring 镗blinster 气泡fillet镶;嵌边through-hole form 通孔形式voller pin formality 滚针形式cam driver 铡楔shank摸柄crank shaft 曲柄轴augular offset 角度偏差velocity 速度production tempo生产进度现状torque扭矩spline=the multiple keys 花键quenching 淬火tempering 回火annealing 退火carbonization 碳化alloy合金tungsten high speed steel 钨高速的moly high speed steel 钼高速的organic solvent 有机溶剂bracket小磁导liaison联络单volatile挥发性resistance 电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die 成型模progressive die 连续模gang dies复合模shearing die 剪边模riveting die 铆合模pierce 冲孑1forming成型（抽凸，冲凸）draw hole 抽孑1 bending 折弯trim切边emboss凸点dome凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch卷圆压平groove压线blanking 下料stamp letter 冲字（料号） shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度press specification 冲床规格die height range 适用模高die height闭模高度burr毛边gap间隙punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin固定销coil spring 弹簧lifter pin顶料销eq-height sleeves=spool 等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring 圆线弹簧outer guiding post 夕卜导柱stop screw 止付螺丝located pin 定位销outer bush夕卜导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder 上夹板stripper pad脱料背板up stripper上脱料板male die公模（凸模） feature die 公母模female die母模（凹模） upper plate 上模板lower plate 下模板die pad下垫板die holder下夹板die set下模座bottom block 下垫脚bottom plate下托板（底板） stripping plate内外打（脱料板）outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch冲头insert入块（嵌入件） deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller滚轴baffle plate 挡块located block 定位块supporting block for location 定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 力口强筋冲子ribbon punch 压筋冲子reel-stretch punch卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad导料块塑件&模具相关英文compre sion molding 压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak 仿皮革shiver饰纹flow mark 流痕welding mark 溶合痕post screw insert螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate 阀门浇口band heater环带状的电热器spindle 阀针spear head 刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line 熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)(成型机)顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation 定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate 侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate 闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate 隔膜浇口ring gate环形浇口subarine gate 潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusionmolding 挤出成形shell casting壳模铸造foam forming泡沫成形sinter forging 烧结锻造forging roll 轧锻six sidesforging 六面锻造gravity casting 重力铸造slush molding凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold有肩柱塞式模具burnishing die 挤光模landed positive mold有肩全压式模具button die镶入式圆形凹模loading shoe mold料套式模具center-gated mold中心浇口式模具loose detail mold活零件模具chill mold冷硬用铸模loose mold活动式模具clod hobbing冷挤压制模louvering die百叶窗冲切模composite dies 复合模具manifold die分歧管模具counter punch 反凸模modular mold组合式模具double stack mold 双层模具multi-cavity mold多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold反套制品模具plaster mold 石膏模blank through dies漏件式落料模porous mold通气性模具duplicated cavity plate 复板模positive mold全压式模具fantail die扇尾形模具pressure die 压紧模fishtail die鱼尾形模具profile die 轮廓模flash mold溢料式模具progressive die 顺序模gypsum mold石膏铸模protable mold手提式模具hot-runner mold热流道模具prototype mold雏形试验模具ingot mold钢锭模punching die 落料模lancing die 切口模raising(embossing)压花起伏成形re-entrant mold倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die对合模具segment mold 组合模semi-positive mold半全压式模具shaper定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold双并式模具sprueless mold无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle调节阻板angular pin 倾斜梢baffle plate折流档板ball button 球塞套ball plunger定位球塞ball slider球塞滑块binder plate 压板blank holder防皱压板blanking die落料冲头bolster上下模板bottom board浇注底板bolster 垫板bottom plate下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug铸耳cavity模穴（模仁）cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring螺旋弹簧cold punched nut 冷冲螺母cooling spiral螺旋冷却栓core心型core pin心型梢cotter 开口梢cross十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach模头料道die bed型底die block块形模体die body铸模座die bush合模衬套die button冲模母模die clamper 夹模器die fastener模具固定用零件die holder母模固定板die lip模唇die plate冲模板die set冲压模座direct gate 直接浇口dog chuck爪牙夹头dowel定位梢dowel hole导套孔dowel pin合模梢dozzle辅助浇口dowel pin定位梢draft拔模锥度draw bead张力调整杆drive bearing传动轴承ejection pad顶出衬垫ejector脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt环首螺栓filling core 椿入蕊film gate薄膜形浇口finger pin指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin带凸缘销flash gate毛边形浇口flask上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib凹形拉紧楔goose neck鹅颈管guide bushing引导衬套guide pin 导梢guide post 弓|导柱guide plate 导板guide rail 导轨head punch顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram压射柱塞inlay busher嵌入衬套inner plunger 内柱塞inner punch 内冲头insert嵌件insert pin嵌件梢king pin 转向梢king pin bush主梢衬套knockout bar 脱模杵land合模平坦面land area合模面leader busher导梢衬套lifting pin起模顶销lining内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush活动衬套making die打印冲子manifold block 歧管档块master plate靠模样板match plate 分型板mold base塑胶模座mold clamp铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set合模定位器pass guide穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate针尖浇口plate衬板pre extrusion punch 顶挤冲头punch冲头puncher 推杆pusher pin衬套梢rack机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin回位梢riding stripper 浮动脱模器ring gate环型浇口roller滚筒runner流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw固定螺丝shedder脱模装置shim 分隔片shoe模座之上下模板shoot流道shoulder bolt肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core)滑块slip joint滑配接头spacer block 间隔块spacer ring间隔环spider模蕊支架spindle 主轴sprue注道sprue bushing注道衬套sprue bushing guide 注道导套sprue lock bushing注道定位衬套sprue puller注道拉料spue line合模线square key 方键square nut方螺帽square thread 方螺纹stop collar 限位套stop pin止动梢stop ring止动环stopper定位停止梢straight pin 圆柱销stripper bolt脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate辅助浇口taper key推拔键taper pin拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin推力销tie bar拉杵tunnel gate隧道形浇口vent通气孔wortle plate拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC 铳床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe仿形车床copy milling machine 仿形铳床copy shaping machine 仿形刨床cylindrical grinding machine 夕卜圆磨床die spotting machine 合模机drilling machine 冲孔机engraving machine 雕刻机engraving E.D.M.雕模放置加工机form grinding machine 成形磨床graphite machine石墨加工机horizontal boring machine 臣卜式搪孔机horizontal machine center臣卜式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center加口工制造中心multi model miller 靠磨铳床NC drilling machine NC 钻床NC grinding machine NC 磨床NC lathe NC 车床NC programming system NC 程式制作系统planer龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M.线割放电加工机模具钢材alloy tool steel合金工具钢aluminium alloy 铝合金钢bearing alloy轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet被覆板clod work die steel 冷锻模用钢emery金钢砂ferrostatic pressure 钢铁水静压力forging die steel锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel超硬合金钢high speed tool steel高速度工具钢hot work die steel热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低镒铸钢marging steel马式体高强度热处理钢martrix alloy马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼车钢nickel chromium steel 镍铭钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite吐粒散铁tungsten steel 钨车钢vinyl tapped steel sheet 塑胶覆面钢板表面处理关连用语age hardening时效硬化ageing老化处理air hardening气体硬化air patenting空气韧化annealing 退火anode effect阳极效应anodizing阳极氧化处理atomloytreatment阿托木洛伊表面austempering奥氏体等温淬火austenite奥斯田体/奥氏体bainite贝氏体banded structure条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing磷酸盐皮膜处理box annealing箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening结晶粒粗大化coating涂布被覆cold shortness 低温脆性comemtite渗碳体controlled atmosphere 大气热处理corner effect锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching表面蚀刻ferrite肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size结晶粒度granolite treatment磷酸溶液热处理graphitizing石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding离子渗碳氮化ion carburizing离子渗碳处理ion plating离子电镀isothermal annealing 等温退火liquid honing液体喷砂法low temperature annealing 低温退火malleablizing可锻化退火martempering麻回火处理martensite马氏体/硬化铁炭metallikon金属喷镀法metallizing真空涂膜nitriding氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite针尖组织phosphating磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 力口压硬化process annealing 制程退火quench ageing淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力。

模具常用语中英文对照

模具常用语中英文对照

种类中文名称英文名称中文名称英文名称模具种类连续模Progressive die 冲孔模Pierce die 机械手Transfer die 剪边模Trimming die 手动机械手Hand transferdie下料模Blanking die 单工程模Single die 成形模Forming die 铸造结构模Cast die 折弯模Bending die 简易模Prototype die 围边模Flange die 铆合模Riveting die 拉伸模Draw die 复合模Compound die 快换模Changeable die工序类料带strip 料带图strip layout 工序process 冲导正孔pilot pierce 冲孔pierce 侧冲cam pierce 切边notch 切侧刃notch french 折弯bend 墩薄 coin成形 form 侧成形 cam form整形 restrike 围边 flange打凸米boss / dimple 打凸包emboss打字印 stamp 打沙拉孔 hourglass 面押 coin burr 抽孔 extrude hole 拍平flat 卷圆curl种类中文名称英文名称中文名称英文名称工序类旋转rotate 铆接 rivet产品切边线 trim line 铆螺母stake nut 切断cutoff 接刀口 mismatch料带带料处carrier tab 毛刺方向burr direction 压线groove 下料blanking模板类上托板top plate 下托板bottom plate 上垫脚upper parallel 下垫脚lower parallel 上模座upper die set 下模座lower die set 上垫板punch backup 下垫板lower backup 上夹板punch holder 下夹板die holder 上脱料板stripper 下模板die plate 冲头punch 凹模die零件类浮块lifter 浮料板 lifter plate 成型公form punch 压料块pressure pad 切边冲头trim punch 刀口trim steel 沉头孔 counter bore 冲孔入子button顶针kick off /ejector废料切断刀slug breaker 成型凹模forming die 整形公restrike punch 导尺rail 导尺顶杆lifter bolt 导料板rail plate 镶件/入子insert侧冲组件 cam 滑块slide滑块上油槽oil groove 铲机 driver码模槽mounting slot 储运块storage block 限位柱stop block 起吊孔 handing hole 起吊环eyebolt 靠块 heel脱料拉杆spool 模座导正块thrust heel种类中文名称英文名称中文名称英文名称零件类耐磨片wear plate 垫片shim压块keeper 初始管位first start pin 键槽 key slot 键 key氮气弹簧nitrogenspring螺旋弹簧coil spring 聚氨酯弹簧urethane 导柱guide post 导套guide bushing 插针 pilot pin插针套 pilot bushing 侧刃 french传感器sensor 销dowel螺丝screw 拔牙 jackscrew垫圈washer 盲销blind dowel压毛边冲头deburring punch 挡块stopping plate 压线冲头groove punch 定位块location block 字模冲头stamp punch 圆冲头round punch压筋冲头ribbon punch 气垫板air cushion plate异形冲头special shapepunch气垫顶杆air-cushioneject-rod切边冲头trimming punch 上压块pressure block加强筋冲头stiffening ribpunch弹簧箱spring box定位板guide plate 弹簧箱顶杆spring-box eject-rod压边圈binder 弹簧箱顶板spring-box eject-plate公差类公差tolerance 公差范围tolerance range 上公差upper tolerance 下公差lower tolerance 公差+/- 0.05plus minus0.05形位公差图GD&T 平面度 flatness 直线度Straightness 倾斜度 angularity 垂直度perpendicularity 平行度 parallelism 圆度 roundness种类中文名称英文名称中文名称英文名称公差类圆柱度 cylindricity 面轮廓度 surface profile 线轮廓度line profile 位置度 true position 同轴度concentricity 对称度 symmetry圆跳动runout 全跳动total runout 尺寸 dimension 角度值angle degree 尺寸全检报告dimensionallayout三次元尺寸报告CMM report冲床机械冲床mechanicalpress油压机hydraulic press相关吨位 tonnage 行程stroke / travel 冲床上台面 ram 冲床下台面bolster冲床台面布置图press layout 冲床上的快速对正QDC 冲床气垫air cushion 码仔stirrup闭合高度 shut height T型槽T-slot送料机feeder 送料高度 feeding height工具卡尺caliper 千分尺micrometer 直尺ruler 高度尺height gage 丝攻screw tap 起子 screwdriver 拨牙器jacker 扳手wrench风磨机hand grinder 油石oil stone加工类开料cuttingmaterial钻drill (DR) 攻牙tap 铰 ream铣mill 车lathe 电脑锣NC mill 线切割wire cutting(W/C) 磨grind 刨planer 电火花EDM 镭射laser cutting 倒角chamfer xx的精加工 finish XX真空热处理vacuum heattreatment镀钛TD coating 退磁demagnetization烧焊 weld4.1.2 加工说明对照表：加工说明Machining Note注:有0.00的地方为数据填入处外导套 OUTER GUIDE BUISHING 起吊杆 HANDING PIN实数铣通 MILL THRU 正反两面各铣 TOP SIDE AND OPP SIDE MILLX:-￠0.00（氮气弹弓过孔，锣穿）单+0.00X:-￠0.00 (DR.THRU FOR GAS SPRING) S+0.00X:-￠0.00（氮气弹弓沉头，正面CNC单+0.00,锣深0.00.)X:-￠0.00 ( CNC C'BORE TOP SIDE FOR GAS SPRING, S+0.00, DP0.00)X:-￠0.00（氮气弹弓沉头，反面CNC单+0.00,锣深0.00.)X:-￠0.00 (CNC C'BORE OPP SIDE FOR GAS SPRING, S+0.00, DP0.00)X:-￠0.00（合销孔,铰)X:-￠0.00 (REAM FOR DOWEL)X:-￠0.00（合销孔,割)单+0.00X:-￠0.00 (W/C FOR DOWEL) S+0.00(正面沉头￠0.00*0.00深,内攻M0.00*1.5牙)(￠0.00*0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)(反面沉头￠0.00*0.00深,内攻M0.00*1.5牙)X:-￠0.00（合销孔,钻穿)X:-￠0.00 (DR.THRU FOR DOWEL)X:-￠0.00（一般孔,钻穿)X:-￠0.00 (DR.THRU HL)X:-￠0.00（穿丝孔,钻穿)X:-￠0.00 (DR.THRU FOR WEDM S.H.)X:-￠0.00（漏油孔,钻穿) 按向视图加工X:-￠0.00 (DR.THRU FOR DRAIN HL) ACCORDING VIEW DRAWING TO MACHINING X:-（漏油槽,反面CNC单+0.00,锣深0.00)X:- (CNC POCKET OPP.SIDE FOR DRAIN, S+0.00, DP0.00)X:-￠0.00（基准孔,铰)X:-￠0.00 (REAM FOR DATUM HL)X:-￠0.00钻穿（螺丝过孔)内攻M0.00牙X:-￠0.00 (DR.THRU FOR CLEARANCE HL, TAP M0.00 THR)(正面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 TOP SIDE)(反面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 OPP. SIDE)(侧面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)X:-M0.00钻穿,反面攻深0.00,有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 OPP.SIDE, THR DP0.00)X:-M0.00钻穿,正面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP SIDE, THR DP0.00)X:-M0.00钻穿,正反面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)X:-M0.00盲孔,反面攻深0.00,有效牙0.00X:-M0.00 BLIND HL, TAP WORK DP0.00 OPP. SIDE)X:-M0.00盲孔,正面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP WORK DP0.00 TOP SIDE, THR DP0.00)X:-M0.00盲孔,正反面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)X:-M0.00盲孔,侧面分中攻深0.00,组模自配X:-M0.00 BLIND HL, TAP DP0.00 ON EDGE FROM CENTER , DIE MAKER FIT) (侧面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)X:-M0.00盲孔,侧面分中钻深0.00X:-M0.00 BLIND HL, DR. DP0.00 ON EDGE FROM CENTERX:-M0.00（拨牙螺丝孔，攻穿）X:-M0.00 TAP.THRU FOR JACK SCREWX:-￠0.00（塞打过孔,钻穿)X:-￠0.00 DR.THRU FOR SPOOLX:-￠0.00（弹弓过孔,钻穿)X:-￠0.00 DR.THRU FOR SPRINGX:-￠0.00（弹弓孔,反面沉深0.00)有效深0.00X:-￠0.00（弹弓孔,正面沉深0.00)有效深0.00X:-（避空孔,锣穿)单+0.00X:- (POCKET THRU)S+0.00X:-（避空孔,正面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 TOP SIDE)X:-（避空孔,反面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 OPP SIDE)X:-￠0.00（避空孔,反面CNC单+0.00,锣深0.00)X:-￠0.00 (POCKET, CNC MILL S+0.00, DP0.00 OPP.SIDE)X:-￠0.00（避空孔,正面CNC单+0.00,锣深0.00)X:-￠0.00 (POCKET, CNC MILL S+0.00, DP0.00 EDGE SIDE)X:-￠0.00（两用销过孔,割)单+0.00X:-￠0.00 (LIFTER PIN, W/C S+0.00)X:-（导尺避空,CNC单+0.00锣穿)X:- (POCKET FOR RAIL, CNC MILL THRU, S+0.00)X:-（导尺避空,正面CNC单+0.00，锣深0.00)X:-（导尺避空,反面CNC单+0.00，锣深0.00)X:-（浮块避空,正面CNC单+0.00，锣深0.00)X:-（浮块孔,割）单+0.00(反面避空单+0.00，锣深0.00)X:-（LIFTER HL, W/C)S+0.00(POCKET DP0.00 S+0.00 OPP.SIDE)X:-（浮块孔,锣）单+0.00(反面避空单+0.00，锣深0.00)X:-（LIFTER HL, MILL)S+0.00(POCKET DP0.00 S+0.00 OPP.SIDE)X:-￠0.00（顶针孔,钻穿)（反面沉头￠0.00*0.00深，内攻M0.00*1.5牙)X:-￠0.00 (EJECT PIN, DR.THRU.)(￠0.00 C'BORE DP0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:-￠0.00（顶针孔,钻穿)（正面沉头￠0.00*0.00深，内攻M0.00*1.5牙)X:-￠0.00 (EJECT PIN, DR.THRU.)(￠0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)X:-￠0.00（导柱（导套）孔,CNC锣)单+0.00X:-￠0.00 CNC MILL FOR GUIDE PIN(BUSHING) S+0.00X:-￠0.00（导柱（导套）孔,割)单+0.00X:-￠0.00 W/C FOR GUIDE PIN(BUSHING) S+0.00X:-M0.00*1.5(止付螺丝，正面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 TOP SIDE)X:-M0.00*1.5(止付螺丝，反面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 OPP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:-（INSERT HL, CNC MILL THRU S+0.00)(阴影部分正面沉头单+0.00，锣深0.00)(SHADE AREA, MILL DP0.00 S+0.00 TOP SIDE)(阴影部分反面沉头单+0.00，锣深0.00)(SHADE AREA, MILL DP0.00 S+0.00 OPP SIDE)X:-（入子孔,割）单+0.00X:-（INSERT HL, W/C S+0.00)(阴影部分扣位正面锣深0.00)(SHADE AREA FOR HEAD POCKET, MILL DP0.00 TOP SIDE)(阴影部分扣位反面锣深0.00)(SHADE AREA FOR HEAD POCKET, MILL DP0.00 OPP. SIDE)(正面沉头单+0.00，锣深0.00)(POCKET, MILL DP0.00 TOP SIDE)注: 此处的沉头不能用C'BORE, 只有圆形的沉头才用C'BORE. (反面沉头单+0.00，锣深0.00)(POCKET, MILL DP0.00 TOP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:- (INSERT HL, CNC MILL THRU. S+0.00)X:-（入子孔,正面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 TOP SIDE)X:-（入子孔,反面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 OPP. SIDE)X:-￠0.00（插针孔,铰)单+0.00X:-￠0.00（REAM S+0.00 FOR PILOT PIN)X:-￠0.00（插针孔,割)单+0.00(正面沉头￠0.00*0.00深)X:-￠0.00（W/C FOR PILOT PIN)(￠0.00 C'BORE DP0.00 TOP SIDE)X:-￠0.00（插针孔,钻穿)(正面沉头￠0.00*0.00深)X:-￠0.00（DR.THRU FOR PILOT PIN)(￠0.00 C'BORE DP0.00 TOP SIDE)X:-（冲头过孔,割)单+0.00(正面避空，CNC单+0.00，锣深0.00)(阴影部分扣位正面锣深0.00)X:-（W/C S+0.00 FOR PUNCH CLEARANCE HL)(POCKET, CNC DP 0.00 S+0.00 TOP SIDE)(POCKET SHADE FOR HEAD, DP0.00 TOP SIDE)X:-（冲头过孔,锣穿)单+0.00(正面避空，CNC单+0.00，锣深0.00)X:-（MILL THRU.FOR PUNCH CLEARANCE HL)(POCKET DP0.00 CNC S+ TOP SIDE)X:-（异形冲孔,直x斜x,割)单+0.00(双线部分，割)单+0.00X:-（W/C FOR SPECIAL HL, 0.00 LAND 0.00 TAPER, S+0.00) (W/C PER DOUBLE LINE S+0.00)X:-（冲孔,直x斜x,割)单+0.00X:-（W/C FOR PIERCE DIE HL, 0.00 LAND 0.00 TAPER S+0.00) X:-（冲孔,割)单+0.00X:-（W/C FOR PIERCE DIE HL S+0.00)X:-￠0.00（冲孔漏屎,钻穿)X:-￠0.00 (DR. THRU FOR CHUTE)X:-（异形冲孔漏屎,CNC单+0.00,锣穿）X:-￠0.00 (MILL. THRU FOR SPECIAL CHUTE S+0.00)X:-（产品落料斜度，实数斜30o锣）X:-（MILL 30 TAPER FOR PART RAMP NO CLEARANCE)X:-（漏屎斜度，直x斜45o锣）X:-（MILL FOR CHUTE 0.00 LAND 45 TAPER)反面沉深底面留0.00MILL UNTIL DP正面沉深底面留MILL UNTIL DP五金模具单词总结模具种类:连续模 progressive die机械手 transfer die手动机械手 hand transfer die单工程模 single die/line die复合模 compound die铆接模 riveting die铸造结构模 cast die能快换的模 changeover die泡沫模 pattern互换性:公差 tolerance上公差 upper tolerance下公差 lower tolerance公差范围 tolerance range公差+/- 0.05 plus minus 0.05形位公差图 GD&T平面度 flatness直线度 straightness倾斜度 angularity垂直度 perpendicularity / squareness平行度 parallelism圆度 roundness / circularity圆柱度 cylindricity面轮廓度 surface profile线轮廓度 line profile位置度 true position同轴度 concentricity对称度 symmetry圆跳动 runout全跳动 total runout尺寸 dimension角度 angle degree全尺寸报告 dimensional layout工艺性:料带 strip料带图 strip layout工序 process冲导正孔 pilot pierce冲孔 pierce侧冲 cam pierce切边 notch成形后的切边 trim切侧刃 french trim / fringe trim 厚料切边后的精修边 shave折弯 bend墩薄 coin折弯处压筋 gusset成形 form侧成形 cam form整形 restrike / rehit围边 flange压线/压长条状筋 ribbon打凸米 boss / dimple打凸包 emboss打字印 stamp打沙拉孔 hourglass面押 coin burr抽孔 extrude hole拍平 flat / spanking包边 hem edge压角 cone张角 flare切舌 lance半剪knockout卷圆 curl/热恶劣旋转rotate铆接 rivet铆螺母 stake nut切断 cutoff接刀口 mismatch料带带料处 carrier tabs毛刺方向 burr direction产品切边线 trim line模具零件:模具 die / tool上托板 upper mounting plate上垫脚 upper parallel上模座 upper die set上垫板 punch backup上夹板 punch holder止挡板 traveling stop脱料板 stripper下模板 die plate下垫板 die backup plate下模座 lower die set下垫脚 lower parallel上托板 base mounting plate 浮块 lifter浮料板 lifter plate成型公 form punch压料块 pressure pad切边冲头 trim punch刀口 trim steel刀口直身位 land直5斜1 5mm Land 1 taper 刀口上沉头的深度 die life 沉头 counter bore冲头倒斜 shear高低冲 stagger punch球锁冲头 ball-lock punch球锁座 ball-lock retainer 冲孔入子 button顶针 kick off / ejector废料切断刀 slug breaker成型凹模form die整形公 restrike form punch 导尺 rail /stock guidance 导尺顶杆 lifter bolt导料板 rail plate镶件/入子 insert侧冲组件 cam滑块 slide滑块上油槽 oil groove铲机 driver码模槽 mounting slot储运块 storage block限位柱stop block起吊孔 handing hole起吊环 eyebolt模柄 shank靠块 heel摆块 rocker bender脱料板拉杆 stripper bolt模座导正块 thrust耐磨片 wear sheet耐磨板 wear plate垫片 shim两用销 lifter pin初始管位 first start pin内限位 standoff压块keeper导柱导套压块 keeper/ boss键槽 key slot键 key氮气弹簧 gas spring / nitrogen spring 氮气弹簧安装法兰 mounting flange氮气弹簧系统 nitrogen manifold螺旋弹簧 coil spring聚氨酯弹簧 urethane弹簧套 spring cage导柱 guide post导套 guide bushing插针 pilot pin插针套 pilot bushing插针通孔 pilot through hole侧刃 french误检装置 misfeeder传感器 sensor误检杆 trigger油嘴 oil nipple销针 dowel pin螺丝 screw牙 thread拔牙 jackscrew内六角螺钉 socket head screw垫圈 washer螺塞 screw plug盲销 blind dowel行程,走位 stroke / travel吨位 tonnage机械冲床 mechanical press油压机 hydraulic press冲床下台面 bolster冲床上台面 ram冲床台面布置图 press layout冲床码模槽 press mounting slot冲床气垫 air cushion码模钳 stirrup闭合高度 shut height送料高度 feeding height送料机 feederT型槽T-slot避位 clearance /pocket掏空 pocket挂台 head扣位 pocket of head通气孔 air vent hole漏油孔 drain hole漏料孔 slug hole基准孔 datum hole通孔 through hole穿丝孔 first wire holeT型槽T-slot拔牙?jackscrew摆块?rocker?bender闭合高度?shut?height避位?clearance?/pocket侧冲组件?cam侧刃?french插针?pilot?pin插针套?pilot?bushing插针通孔?pilot?through?hole铲机?driver沉头?counter?bore成型凹模form?die成型公?form?punch冲床码模槽?press?mounting?slot 冲床气垫?air?cushion冲床上台面?ram冲床台面布置图?press?layout冲床下台面?bolster冲孔入子?button冲头倒斜?shear初始管位?first?start?pin储运块?storage?block穿丝孔?first?wire?hole?传感器?sensor弹簧套?spring?cage氮气弹簧?gas?spring?/?nitrogen?spring 氮气弹簧安装法兰?mounting?flange氮气弹簧系统?nitrogen?manifold刀口?trim?steel刀口上沉头的深度?die?life刀口直身位?land导尺?rail?/stock?guidance导尺顶杆?lifter?bolt导料板?rail?plate导套?guide?bushing导柱?guide?post导柱导套压块?keeper/?boss垫片?shim垫圈?washer顶针?kick?off?/?ejector吨位?tonnage废料切断刀?slug?breaker浮块?lifter浮料板?lifter?plate?高低冲?stagger?punch挂台?head滑块?slide滑块上油槽?oil?groove机械冲床?mechanical?press基准孔?datum?hole键?key键槽?key?slot聚氨酯弹簧?urethane?靠块??heel扣位?pocket?of?head两用销???lifter?pin漏料孔?slug?hole?漏油孔?drain?hole螺塞?screw?plug螺丝?screw螺旋弹簧?coil?spring码模槽?mounting?slot码模钳?stirrup盲销?blind?dowel模柄?shank模具?die?/?tool模座导正块?thrust内六角螺钉?socket?head?screw 内限位?standoff耐磨板?wear?plate耐磨片?wear?sheet起吊环?eyebolt起吊孔?handing?hole切边冲头?trim?punch球锁冲头?ball-lock?punch球锁座?ball-lock?retainer上垫板?punch?backup上垫脚?upper?parallel上夹板?punch?holder上模座?upper?die?set下托板?base?mounting?plate 上托板?upper?mounting?plate 送料高度?feeding?height送料机?feeder掏空?pocket通孔?through?hole通气孔?air?vent?hole脱料板?stripper脱料板拉杆?stripper?bolt误检杆?trigger误检装置?misfeeder?下垫板?die?backup?plate下垫脚?lower?parallel下模板?die?plate下模座?lower?die?set?限位柱stop?block镶件/入子?insert销针?dowel?pin行程,走位?stroke?/?travel压块keeper压料块?pressure?pad牙?thread油压机?hydraulic?press油嘴?oil?nipple整形公?restrike?form?punch?直5斜1??5mm?Land?1?taper止挡板?traveling?stop机加工:开料 cutting material钻drill (DR)攻牙 tap铰 ream铣 mill车 lathe电脑锣 NC mill线切割wire cutting (W/C)磨 grind刨 planer电火花 EDM镭射laser cutting倒角 chamfer精加工 finish XX真空热处理 vacuum heat treatment镀钛TD coating退磁 demagnetization烧焊 weldG :40-M6BLIND HL,TAP DP18.00 OPP SIDE,THR DP18.00) 盲孔，反面攻深**G10:4-M30BLIND HL,TAP DP18.00 EDGE SIDE)盲孔，侧攻深**(%%c34.00*14.00 C'BORE DP14.00 TOP SIDE) 正面沉头多少×多少深G2 :24-%%c8.00(REAM FOR DOWEL WORK DP16.00 OPP SIDE,DR%%c6.00 HL)G2 :24-%%c8.00(合销,背铰深16.00,有效深,内钻%%C6.00通孔)G4 :3-%%c10.00(基准孔,背铰深20.00)背面锣25.00*25.00方形沉头，深1.00%%P0.01 (REAM FOR DATUM HL DP20.00,MILL25.00*25.00 OPP SIDE DP1.00%%P0.01)M:2-%%c15.00(弹簧孔,锣深33.00) (C'BORE OR SPRING DP33.00 TOP SIDE,WORK DP33.00)X :3-%%c32.00(导套孔,锣穿,单+0.01)(MILL THRU FOR GUIDE BUSHING S+0.01)G :2-M10盲孔,侧攻深30.00(有效深)(BLIND HL,TAP WORK DP30.00 EDGE SIDE)(沉头5.20%%P0.05深)(SLOT DP5.20%%P0.05 TOP SIDE)L :2-%%c8.000(合销,割)单+0.005 (W/C FOR DOWEL)S+0.005盲孔,攻深20.00(有效深) (BLIND HL,TAP DP20.00 TOP SIDE,THR DP20.00)(插针孔,割,单+0.01) (W/C S+0.01 FOR PILOT PIN)(避位孔,背锣9.80(有效深) (POCKET,MILL DP9.80 OPP SIDE WORK)(冲头过孔,锣穿) (MILL THRU FOR PUNCH CLEARANCE HL)(导柱孔,锣穿,单+0.005) (MILL FOR GUIDE PIN) S+0.005避位槽,背锣深19.00) (POCKET,MILL DP15.40 OPP SIDE)(背,沉头%%c14.00，掏深留11.00) (%%c14.00 C'BORE UNTIL DP14.00 OPP SIDE) 下模刀口，实数割，直5斜1.5 （内钻%%C5.0穿丝孔）W/C S+0.00 TRIM STEEL,5.0LAND 1.5TAPER,(DR THRU%%c3.00 WEDM S.H)(MILL FOR INSERT DP30.0%%P0.01 S+0.01)(入子槽,锣深30.00%%p0.01,单+0.01)(氮气槽,背锣深4.00%%P0.1,单+0.1) (GAS SPRING MILL DP4.00 OPP SIDE)S+0.1 按向视图加工ACCORDING VIEW DRAWING TO MACHINING试模材料:热扎板 HRS (hot-roll steel)冷扎板 CRS (cold-roll steel)不锈钢板Stainless steel镀锌板galvanized steel镀铝锌板galvalume steel热扎酸洗板HRPO steel (hot-rolled pickled and oiled steel)工具:卡尺 caliper千分尺 micrometer拨牙器 jacker扳手 wrench丝攻 screw tap起子 screwdriver码模钳 stirrup设备/工具:3D Programmable CMM三次元检测仪3D CMMBeam Drilling Machine摇臂钻Bench Drilling Machine钻铣床Caliper卡尺CNC EDM电火花机CNC Machine Center加工中心CNCCNC Milling Machine数控铣床CNCCNC Planer Type Milling Machine龙门刨铣床Hardness Tester硬度计Height Gauge高度仪High Wire Cutting快走丝Hole Puncher 打孔机Horizontal surface grinder小水磨/卧式平面磨床Horizontal surface large grinder大水磨Lathe车床Measurement Surface Plate测量平台Metal Saw Machine锯床Milling Machine铣床Oil Press油压机Pin Gauge标准针规Plastic Injection Machine注塑机Point to Point CMM三次元测量仪Precision surface grinder精密手摇磨Press冲床Projector profile投影机Shear Press剪板机Slow Wire Cutting慢走丝Vertical Milling Machine卧式强力铣床扳手?wrench拨牙器?jacker卡尺?caliper码模钳?stirrup起子?screwdriver千分尺?micrometer丝攻?screw?tapCARVE 雕刻pothook 挂钩SPECIAL HL 异形孔漏斗 filler角铁 ANGLE IRON展开 expanding微调开关 INCHING SWITCH合叶 HINGE优力胶 RUBBER球锁垫板 LOCK WASHER双线边刀口,不倒角TRIM STEEL NEAR THE DOUBLE LINE NO CHAMFER滑块座:SLIDE SET机械:（engine type) liquid cooled, in-line, 4cylinder, carb (发动机型号)水冷，直列，四缸，化油器式(engine) compression ratio (发动机)压缩比(engine) displacement (发动机)排量(engine) fuel (发动机)燃料13-mode 13工况3rd gear 三档齿轮3-way seat 三向座椅4WD control device 四轮驱动控制装置4WD indicator switch 四轮驱动指示灯开关4WD lamp electrical connection 四轮驱动指示灯接线4WD switch 四轮驱动开关5th synchromesh assy. 五档同步器总成6PK belt 6PK 多楔驱动皮带A / C compressor assembly 空调压缩机总成A / C control assembly 空调控制装置A/C & heater assy. 空调加热器总成A/C blower 空调鼓风机A/C clutch 空调压缩机离合器A/C compressor MTG bracket 空调压缩机安装支架A/C control assy. 空调控制器A/C housing assy. 空调箱总成A/C low pressure switch 空调低压开关A/C mode select switch 空调状态选择开关abdomen performance criterion 腹部性能指标Abdominal Peak Force 腹部力峰值ABS 防抱死制动系统acceleration fuel system 加速系统acceleration running noise level 加速行驶噪声accelerator interlocking type 加速踏板联锁式accounting foundation 财政基础Actual cycle work 实际循环功Actual torso angle 实际躯干角adapter 连接器additional features 附加装置additional rule 附加法规adjust screw 调整螺钉adjuster cable 调整拉线adjuster plug 调整盖adjuster screw assy. 调整螺栓总成adjuster washer 调整棘片adjuster, diff. bearing 差速器轴承调整螺母Adjustment system 调节装置Administration and Registration Division 管理科Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts Which Can Be Fitted and/or Be Used on WheeledVehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of These Prescriptions关于对轮式车辆、安装和/或用于轮式车辆的装备和部件采用统一条件并相互认可基于上述条件批准的协定书Agreement Regulations 协定法规air cleaner 空气滤清器air cleaner assy. 空气滤清器总成air cleaner cartridge 空气滤清器滤芯Air compressor 空压机air condition compressor 空调压缩机air direct 空气走向air filter 空气滤清器air flow 空气流向Air flow meter 空气流量计air jet 空气量孔air metering hole 空气量孔air path 气道Air Pressure of Tire 轮胎气压Air type 空气型air valve 空气阀air-cooled 风冷Aisles 通道Alcohol 酒精all bearing 球轴承alternater bracket 发动机支架alternator 交流发电机alterntor assembly 交流发电机总成alumininum-rim 铝合金钢圈alumininum opposed model 铝制对开式AM/FM cassette stereo radio 调幅/调频立体声收放机ambulance 救护车Amended by 修正文amount of exhaust emission 排气排放量Amplitude resolution 幅度分辨率Analogue magnetic recorder 模拟式磁记录仪ANALYZER 分析仪anchor plate, brake caliper 制动钳安装支架Anchorage 座椅固定装置Angle of divergence 偏离角Angle of rotation 旋转角angles drift off vertical line 指针偏离垂直线的角度Angular diameter of the retro-reflecting device 回复反射装置的角直径annex 附件Announcement 公告anti, shutdown screw 防不灭车调整螺钉Antilock Brake System 防抱死制动系统appendix 附录Applicable motor vehicle 适用机动车Applicable scope 适用范围applicant 申请人application 申请application for notification 认可申请书approval 认可arm, valve rocket 摇臂armature 转子总成armature shaft 电枢轴Arm-rests 靠手Article 条Article 1 第1条Asphalt solution 沥青溶剂Attached document 附署文件attached sheet 附表Attached Table 附表attaching location of seat belt anchorage 座椅安全带固定装置的固定位置attachment 附属文件Attendants onboard 车上值班人员automatic chock cover setting 自动阻风门盖调到automotive electric system 汽车电系automotive engine system 引擎系统automatic transmission 自动变速器，自动排挡变速箱Auxiliary Brake 辅助制动器Auxiliary Direction Indicator Lamps 辅助转向信号灯auxiliary spring 副簧Auxiliary Stop Lamp 辅助驻车灯axle case 桥壳axle case assy. 桥壳总成axle ratio 桥速比axle tube 桥管axle weight 轴重back angle level 靠背角水平仪back angle quadrant 靠背角量角器back pan 靠板back spring 回位弹簧backing plate 制动底板Backing sheet 衬背板Back-Up Light 倒车灯backup washer 支撑挡圈bail wire 卡紧环balance tube 平衡管ball 钢球ball bearing 球轴承ball joint assy. , upper 上球销总成ball valve 球阀ball valve, inlet 进油口球阀bar 拉杆barrier 障碍壁battery 蓄电池battery terminal 蓄电池接线柱bearing cap 轴承盖bearing cover, input shaft 输入轴轴承盖bearing, connecting rod 连杆轴承bearing, input shaft 输入轴轴承Bed for babies 婴儿床bell 带束层bench seat 长条座椅berived cap 轴承盖bezel assy. 框板总成bezel, cluster 表框be pilot 小批量产品blead door 混合风门bleeder screw 放气螺钉blower assy. 鼓风机总成blower motor 鼓风发电机blower resistor 鼓风机电阻blower switch 鼓风机开关body 车身,阀体body & liftgate assembly 车身和举升门总成body assy. 车身总成body block 人体模块body of A/C & heater 空调加热器壳体bolt 主缸连接螺栓bolt, connecting rod 连杆螺栓Booster 助力器boot 护罩BOSCH starter motor assembly “波舍”起动机总成bottle assy. , coolant recover 冷却液回收罐总成bottom houseing, fuel pump 燃油泵下壳体bottom housing, fuel tank 燃油箱下壳体bracket 支架bracket assy. , spring seat 弹簧座支架bracket, steering damper mounting 转向减振器支架brake alarm lamp 制动报警灯brake alarm lamp switch 制动报警灯开关Brake booster 制动助力器brake caliper 制动钳brake caliper assy. 制动钳总成brake caliper piston 制动钳活塞brake combination valve 制动组合阀brake disc 制动盘Brake drum 制动鼓brake fluid 刹车油Brake hose 制动软管brake lining 刹车来令brake line, LF 左前制动油管brake line, RF 右前制动油管brake oil flow 制动液流向brake paddle 制动踏板brake pedal 制动踏板Brake pipe 制动管brake shoes 刹车蹄片brake shoe 制动衬块Brake System 制动系Brake Systems for Tractors and Trailers 牵引车及挂车的制动装置Brake tester 制动器试验台brake valve 制动阀brake warning lamp 制动报警灯brake warning switch 制动报警开关Braking efficiency 制动效能braking force control system 制动控制装置Braking wheel 制动轮branch office 分署breaker 断电器bridge 过桥broadcasting vehicle 广播车brush 碳刷总成Buckle 带扣bulkhead 隔板Bulldozer 推土机bumper 保险杠Bumper element 保险杠构件bus transfer 车辆转移台bushing 衬套bushing, upper control arm 上控制臂衬套Business Place 业务场所bypass valve 旁通阀Cabinet Decision 内阁决议cable guide 拉线导向块cable-operated control system 液压式离合器系统Calibration factor of a data channel 数据通道校正系数calibration gas 标定气体calibration method 标定方法caliper assy. , front brake 前制动钳总成Camber 外倾camber angle 前轮外倾角camshaft 凸轮轴camshaft oil gallery 凸轮轴油道cap 加机油口盖cap assy. , power steering fluid reservoir 动力转向液油罐盖cap assy. , radiator 散热器盖总成cap screws 螺钉cap, connecting rod 连杆盖Capacity 容量,规格Capacity of the fuel tank 燃油箱容量capillary tube 毛细管carbon brushes & brush holder 电刷支架总成Carbon monoxide measuring instrument 一氧化碳分析仪Carburetor 化油器carburetor assy. 化油器总成carburetor bowl 化油器浮子室carburetor bowl vent system 化油器浮子室通风系统carburetor overhaul scheme 化油器分解图carburetor working scheme 化油器工作示意图carcase 胎体case runout (Max.) 差速器壳圆跳动（最大）Caster 后倾Catalyst 催化器category 类别cement and aggregate 水泥和混凝料Centreplane of occupant 乘员中心面Certified 经认证的Cetane number 十六烷值chain 驱动链chain drive 驱动链Channel amplitude class 幅度级通道Channel Frequency Class 频率级通道chassis 底盘chassis dynamometer 底盘测功机chassis shuttle 底盘平移台chassis number 底盘号Check and Maintenance 检查和保养check assy. , front door 前门限位器总成check assy. , rear door 后门限位器总成check ball 回止球check bracket 限位器支架check nut 限位器螺母check valve 单向阀check valve hole 回止阀孔check valve retainer 单向阀保持架check valve spring 单向阀弹簧check weight 回止块Chigi Circular No. 地技第…号Chigi No. 地技第…号Child Restraints 儿童约束装置chime module 蜂鸣器Chishin Circular No. 地审第…号Chishin No. 地审第…号chock heater 阻风门加热器总成chock plate 阻风门chock unloaded 阻风门连动装置choke 阻风门choke device 阻风装置choke unload mode 阻风门卸载状态cigarette lighter 点烟器circuit breaker, wiper/washer 刮水器/洗涤器电器断路器Circular 通告circular notice 通告clamp 卡圈Clamp ring type 锁紧圈式Cleaning efficiency 清洗效率Cleaning period 清洗周期clearance 最小离地间隙Clearance Lamp 示廓灯clinder head 气缸盖clip 卡子cluster housing 组合仪表壳Clutch system 离合器clutch assembly 离合器总成clutch control device 离合器控制装置clutch disc,clutch 离合器片clutch housing 离合器壳clutch master cylinder 离合器主缸clutch working cylinder 离合器工作缸Coating 涂层Code No. 型号Code of Federal Regulations 美国联邦法规总览Coefficient of luminous intensity (CIL) 亮度系数coil spring 圈状弹簧cold air 冷空气cold cranking voltage(min.) 最小冷启动电压collapsible spacer 可压缩隔垫collector 拼装台colorimeter 色度计coloured-light unit 有色灯光组column assy. 转向管柱总成combination brake switch and proporting 组合阀combined lamp 复合灯combined pump 复合泵combined pump diaphragm 复合泵膜片combined pump diaphragm rod 复合泵膜片杆combined pump lifter link 复合泵举升拉杆combined pump move direct 复合泵运动方向Combustion Chamber 燃烧室commutator 换向器compensate opening 补偿孔completion inspection certificate 终了检验证书Completion of notification 完成认可compressor 压缩机compression (both) 气环槽（两个）compression ignition type 压燃式Compression ratio 压缩比concrete mixer truck 混凝土搅拌车condenser 冷凝器condenser assy. 冷凝器总成conduit pipe 导管cone , diff. side bearing 差速器轴承，内圈带滚子cone, pinion front bearing 主动齿轮前轴承内圈带滚子cone, pinion rear bearing 主动齿轮后轴承内圈带滚子Confirmor 确认者connecting rod 连接杆connecting link 连接杆connecting rod journal diameter 连杆轴径connecting rod journal width 连杆轴径宽度connecting rod throttle 连杆喷油孔connector 连接器connector of service valve 维修阀接口Constant speed 等速construction and device 结构和装置control & tube assy. , hyd clutch 离合器工作缸和油管总成Control System 操纵系control valve 控制阀阀门control valve model 控制阀型式control valve seat 控制阀阀座convex plate 凸台cooling fan 冷却风扇cooling system 冷却系统Cornering Lamp 转弯灯corrected 修正的cotter 开口销counter 5th gear 中间轴五档齿轮counter shaft 中间轴coupled condition 连接状态Coupling Device 牵引装置cover 端盖cover & plate assy. 离合器盖及压盘总成cover assy. , air cleaner 空气滤清器盖总成cover, gear 侧盖cover, heater air 空气加热罩cover, rear axle case 后桥壳盖crane vehicle 起重车crankcase 曲轴箱crankshaft 曲轴crankshaft gear 曲轴齿轮crankshaft & connecting 曲轴连杆机构crankshaft oil gallery 曲轴油道crankshaft sprocket 轴承链轮critical flow 临界流Cross sensitivity of a linear transducer 线性传感器的横向灵敏度Crush distance 压碎距离Crush rate 压碎速率Crush Strength 压碎强度Cumulative time 累计时间cup 皮碗cup, diff. side bearing 差速器轴承外圈cup, pinion front bearing 主动齿轮前轴承外圈cup, pinion rear bearing 主动齿轮后轴承外圈Cut-off 明暗截止线cycle 冲程cyclinder head cover 气门室罩Cylinder 气缸cylinder block 汽缸体cylinder body 缸体Cylinder bore 缸径cylinder head 汽缸盖cylinder head cover 气门室罩cylinder number 气缸数cylinder working order(clockwise) 气缸工作顺序（顺时针）damper 转向减振器dangerous article 危险物darkroom 暗室Data channel 数据通道Data Processing 数据处理Date of notification 认可日期Deceleration of the structure 地板减速度Definitions 定义Definitions 术语deflection 偏移defroster 除霜器dehydrator 储液器和干燥器delay valve 延迟阀Design torso angle 设计躯干角。

模具常用术语中英文对照

模具常用术语中英文对照

模芯Parting Core 耐落胶Teflon Paste局部视图Partial View 偏移量Offset冷料Cold Slag 水塞Water Line Plug线切割Wire E.D.M 撬模脚Ppy Slot轮廓Contour 重新加工Reworked螺纹孔Tapping Hole 配件Components连接件Fittings 补偿Compensation斜针Angle Pin 平面度Parallel接合Engage 倒角Chamfer替换镶件Interchangeable Mold Inserts 模胚Mold Base指定吨位的注塑机Specific Press 热嘴Hotnozzle水嘴接头Water Fitting 火花机Edm螺纹Eyebolt Thread 熔接线Weildline回针Stop Pin 压机Press二级顶出针Sub-Leaderd Pin 嗮纹Texturing镶件Mold Insert 梯形Trapezoid加硬Harden 凸缘、法兰Flange唧嘴Sprue 方铁Spacer Block设计筒图Design Preliminary 顶针板Ejector Plate名称块表Title Block 顶针底板Ejector Retainer Plate 版本标识Revision Level 垫板Retainer Plate材料清单Stock List 后模镶针Core Pin制模Build Mold 垃圾钉Stop Pin手动滑块Hand Slide 有托顶针Shoulder Ejector Pin漏水测试Leak Test 顶针板导套Guided Ejection Bushing流道排气Runner Vents 针板导柱Guided Ejection Leader Pin抛光Draw Polish 唧嘴Sprue Bushing侧抽芯Slide Action 三板模延伸式唧嘴Extension Noozzle Bulishing 加强筋Reinforcing 水口板导套Runner Stripper Pin三角撑Gusset 定位圈（法兰）Locating Ring柱子Bossed 管钉（定位销）Dowel Pin出模斜度Draft 管状管钉Tubular Dowel外廊Contour 吊环Safety Hoist Ring落单会议Kick-off 日期印Dating Insert装卸孔Handing Hole 环保印Recycling Insert运输安全带Moldstrap 气顶Air Poppet Valve码模槽Clamp Slot 截水口镶件Runner Shut-Off Insert撑头Support Pillar 早回Early Ejector Return螺牙1/2-13 Eye 1/2-13Tap 加速项Accelerated Ejector导柱位Leader Pin Location 客户Client产品名Part Name 产品编号Part No缩水Shrinkage 版本Rev下模镶件Core Block 上模镶件Cavity Block小镶件Sub-Insert 下模小镶件Core Sub-Insert上模小镶件Core Sub-Insert 行位Slide行位镶件Slide Insert 压条Gib压紧块（铲机）Jaw 扁顶Blade硬片（摩擦片）Wear Plate 出模斜波Draft水口铁Runner Bar 手动滑块模具Hand Slide-In Type Mold 上模水口铁Upper Runner Bar 回针板Backup下模水口铁Lower Runner Bar 合模Shutoff弹簧Spring 空隙槽Clearance Slot水口钩针Sprue Puller Pin 导柱及导套Leader Pin Bushing顶针Ejector Pin 水口拉钩Spuer Puller撑头Support Pillar 模框镶件Pocket Insert直身锁Side Lock 成型热固性塑料模具Thermoset Mold 斜度锁Inter Lock 三板模3-Plat Mold锁模板Safty Bar 分型面Parting Line‘O’令（密封圈）O’Ring 司筒Ejector Sleeve喉塞Plug 垫圈Washer隔水片Baffrle 烙接线（夹水纹）Weldlin波子螺丝（行为定位螺丝）吸针Sucker Pin斜顶Lifter 回针板Retainer Plate控制开关Switch 顶出板Knock-Out Plate回针Return Pin 电动安全开关Electrical-Safety Switch 斜导柱Angle Pin 脱开Cut Of Position推板Stripper Plate 预先决定PreloadA’板A’Plate 缓冲器BumperB’板B’Plate 衬垫Cushion方铁（垫铁）Spacer Block 公差Tolerance顶针板Ejector Plate 突然性动作Slam顶针底板Ejector Retainer Plate 销针Dowel垫板Retainer Plate 钩槽Gib精磨Finished 有托顶针Shoulder Ejector Pin通框Through Window 顶针板导套Guided Ejector Bushing 粘后模Stricking Core 针板导柱Guided Ejector Leader Pin 粘水口Sticking Sprue 不干胶Adhesive Sticker夹水纹Weld Line 线切割Wire-Cut变形Warpage 电火花Edm走水不平均Filling 抛光Polishing走不齐Short Shot 蚀纹Texture挂成品Part Hanging 探热针Thermocouple漏水Water Leakage 三打螺丝毫（限螺丝）Stripper Bolt 刮花（擦伤）Galling 盖板Cover Plate漏电Ele Leakage 齿轮Gear困气Air Trapping 油唧Hydraulic Cylinder温度Temperature 司筒Ejector Sleeve注塑模Injection Mold 导柱Leader Pin入水Gate 冷料Cold Slag试板Sampling 压力Pressure倒圆Fillet 螺纹孔Tapping Hole顶棍Ejector 连接件Fitting顶白Stress Mark 粘前模Sticking Cav名称块表Title Block 替换镶件Interchangeable Mold Insert版本标识Revision Level 制定吨位的注塑机Specific Press材料清单Stock List 水嘴接头Water Fitting斜导柱（斜边）Angle Pin 螺纹Eyebolt Thread分模面Parting Surface 倒扣Under-Cut披峰Flash 锁定位Lock缩水Sink Mark 楔子（铲机）Wedge氮化Nitride 高产量模量High Volume Running Mold 不规则四边形Trapezoid 剖面图Cross Section缩水Shrinkage 模具结构Mold Construction连续的Consecutive 出模角Draft热流道Manifold 擦位Shut-Off(S/O)型腔数Cav No 导套Bushing模号Mold No 导向针Guide Pin回针Return Pin 胶料Material加硬Harden 尺寸Dimension唧嘴Sprue 重要尺寸Critical Dimension设计筒图Design Preliminary 雕刻Engrave丝印Silkprint 托司EJ.Guide Pin。

模具常用术语中英文对照

模具常用术语中英文对照

模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料# Cold Slag线切割Wire E。

D。

M轮廊Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick—Off Meeting装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2—13 Eye Bolt 1/2—13Tap 导柱位Leader Pin Location耐落胶Teflon Paste偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate 垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰) Locating Ring管钉(定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut—Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub—Insert下模小镶件Core Sub—Insert 上模小镶件Cavity Sub-Insert 行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar 下模水口铁Lower Runner Bar 弹簧Spring水口勾针Sprue Puller Pin 顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令(密封圈）O’Ring 喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball—Catch 斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA'板A’PlateB’板B'Plate方铁(垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing 针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉(定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut—Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide—In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3—Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹) Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock —Out Plate电动安全开关Electrical—Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花(擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模※※※※ction Mold 入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板A’plateB板B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut—Off(S/0）导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire—Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag线切割Wire E.D。

模具常用术语中英文对照

模具常用术语中英文对照

文档从网络中收集，已重新整理排版.word版本可编辑.欢迎下载支持.富达金实业"Fudakin Insdustrial Co.,Ltd"模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料井Cold Slag /collect slag线切割Wire E.D.M轮廓，外廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针,垃圾钉 Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft落单会议Kick-Off Meeting装卸孔Handling Hole运输安全带Mold strap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap导柱位Leader Pin Location 耐落胶Teflon Paste偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hot nozzle火花机 E.D.M熔接线Weld line压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar下模水口铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin 顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹） Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven 走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板 A'plateB板 B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计简图Design Preliminary 丝印Silk print不干胶Adhesive Sticker 导向针Guide Din公差Tolerance 线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt 盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High Volume Running Mold 剖面图Cross Section模具结构Mold Construction模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension雕刻Engrave托司 EJ.GUIDE PIN料花 Silver。

模具图中常见英文词语

模具图中常见英文词语

模具图中常见英文词语ADAPTER 管接头ADHESIVE GLUE 粘结剂AIR CYLINDER 气缸AIR PIPING SET 空气管路装置AIR VENT TUBE 空气排气管AIR VENT TUBE （COPPER）空气排气管（铜管）AIR VENT TUBE （NYLON）空气排气管（尼龙管）BACK UP KEY止退键BACKUP 止退5°BACK5°负角BEAD 拉延筋BELL CRANK LIFTER SET 曲柄顶升机构BLANCER PLATE 平衡块BLANK DIE 落料模BLANKHOLDER STOPPER BOLT 压边圈限位螺钉BLANCER BLOCK 平衡块BOSS HOOK 铸造吊柄BOTTOM BLOCK 压靠块BOTTOM DIE 凹模镶套BOTTOM MARKE 到底标记BOTTOM PLATE 到底块、镦靠块BOLSTER SIZE （压机）工作台尺寸B/H （BLANK HOLDER ）压边圈BOLT 螺栓BOLT TYPE HOOK 螺栓型吊钩BUSING 套管C/HCAM BOTTOM GUIDE PLATE 斜楔底部导向板CAM BOTTOM SLIDE PLATE 斜楔底部滑板CAM DIE 斜楔模1CAM PAD KEEPER 斜楔压料器保位装置CAM POSITIVE RETURN FOLLER 斜楔刚性回程随动器CAM RETURN PLATE 斜楔回程板CAM RETURN UNIT 斜楔返回装置CAM SLIDE 斜楔滑板CAM SPRING UNIT 斜楔弹簧组合件CAM STOPPER 斜楔限止器CAM STROKE PLATE 斜楔行程楔块CASTING DIMENSIONS 铸造尺寸CHECKING FIXTURE 检具CAST IN NUT 铸入式螺母CAST IN HOOK 铸入式挂钩CAST IN LIFTING BUSH 铸入式起重衬套CAST IN PIPE 铸入式导管COIL SPRING 卷形弹簧COIL SPRING GUIDE 弹簧导销COLLAR 杆环（轴环、垫圈等）CONTROL PANEL 控制板COTTER PIN 开尾销COUPLING NUT 联接螺母COUPLING PLATE 联接板COUPLING SLEEVE 联接套COVER 防护罩CUT SECTIONAL 分段切割(废料刀分布)DIE 模具DATUM LINE 基准线DIFFERENCE ELBOW 差异式管接头（不等径）DIFFERENCE SOCKET 差异式管接座（不等径）DISTANCE BLOCK 定距块（等高块）DOUBLE ACTION DRAW 双动拉延DOWEL PIN 销DETAIL 放大2DCP（DIE CHECK POINT）模具检测点DIRECTION OF FEED 送料方向ECONOMY REAR GAUGE 经济型后挡料器EJECTOR 顶出装置ELBOW 弯管接头ELECTRISTIC PARTS 电器部件EMBOSS（PUNCH INSERT）压印、压凸点（凸模镶嵌件）FASTENING SLOTS固定槽F EED 送料FINAL PRESSURE 最终压力FLANGE DIE 翻边模FLANGE LIFTER 翻边顶升器FLANGE LIFTER BLOCK 翻边顶升器顶升块FLANGE LIFTER GAUGE BLOCK 翻边顶升器挡料块FLANGE LIFTER PUSH PIN 翻边顶升器推销FLYING 飞行式（吊装式斜楔）FOME 成形FRONT GAUGE 前挡料板GAS SPRING 氮气弹簧GAS SPRING MOUNTING 氮气弹簧固定件GAS SPRING HOSE SYSTEM斥氮气弹簧管道系统GAUGE 测量、量规、样板GUARD 防护装置GU IDE PIN 导向销GUIDE POST 导向柱GUIDE BUSH 导向衬套GUIDE BAR 导板GUIDE ROLLER 导向滚轮3HARCROSS LIFTERHAND VALVE 换向阀HEADER BLOCK 管接头集成块H EEL 跟部HEM DIE 包边模HEX NUT 六角螺母HEX BOLT 六角螺栓HOLE SET PLUG 孔塞头HOLDER PLATE 托板HOOK 挂钩HOOK PIN 挂销HORIZONTAL DATUM LINE 水平基准线HOSE CLAMP 软管夹HOSE JOINT 管接头HEXAGON NUT 六角螺母INCLINED 倾斜式INCLINATION REAR GAUGE 倾斜式（偏翻式）后挡料器INR SLIDER 内滑块INR HEIGHT 内模高度INSERT 镶嵌件INITIAL PRESSURE 最初压力JECTOR PUNCH顶料凸模KEY 键KEEPER 保位物KEEPER PLATE 限位块LATCH LIFTER 碰锁式提升装置LIFTER 升降器LIFTING LOAD 顶升载荷LIMIT SWITCH 行程开关（终端开关）4LOAD 装料（装载）LOADING STAY 重量支撑、限止器LOCATING CONE 定位锥LOCATION KEY 定位键LOCATION PIN 定位销-LOCK BEAD 拉延槛LOCK NUT 锁紧螺母LOCKER CHAIN 链条LOWER STEEL 下刀块MCS(MASTER CONTRL SURFACE)主控面MAGNET 磁铁OTR SLIDER 外滑块OTR RISER 外垫板NEST GUIDE导向套NIPPLE 螺纹接头NUT 螺母NYLON TUBE 尼龙管PAD 压料芯PANEL CHUTE 板料滑槽（板料装卸托架）PIERCE DIE 冲孔模PIERCE PUNCH（BALL LOCK TYPE）冲孔凸模（球锁紧）PIERCE PUNCH（SHOULDER TYPE0 冲孔凸模（台肩式）PIERCE PUNCH（LIGHT DUTY）冲孔凸模（轻载荷）PIERCE PUNCH（HEA VY DUTY）冲孔凸模（重载荷）PIN TYPE GAUGE 销式挡料器PIN TYPE HOOK 销型吊钩（起重棒）PLAIN WASHER 垫圈--------PLAN VIEW OF LOWER DIE 模具下平面图PLATE TYPE HOOK 板式吊钩5PLATE TYPE GAUGE 板式挡料器PLUG 插头PNL IMPUT DETECOR 板件到位探测器POSITIVE RETURN 刚性回程装置（确定回位）PROGRESIVE DIE 连续模PUNCH 凸模PUNCH PROFILE 凸模轮廓线PUNCH RETAINER 凸模固定座（保持器）PUNCH WITH CENTER HOLE 带中心孔的冲头PUSH PIN 推销PUSHER 推进器QUICK EXHAUST V ALVE快速排气阀RACK 齿条REGULAR PUNCH 固定冲头RESTRIKE DIE 整形模R ETAINER BOLT 卸料螺钉、止动螺钉RETAINER PIN 导销RIB 肋RING BOLT/HOOK 环形吊钩REQUIRE PRESSURE 要求压力ROLLER CARRIER 滚动式传送器ROUGH GUIDES 粗导向器ROUGH TRIM 粗修边RUBBER ROLLER 橡胶滚轮SAFETY AREA 安全区域SAFETY BLOCK 安全块（或保险块）SAFETY BLOCK FOR STORAGE 存放装置SAFETY COVER 防护罩SCRAP BOX 废料盒SCRAP BOX GUIDE 废料盒导向板6SCRAP BREAKER 废料破碎装置SCRAP CHUTE 废料滑槽SCRAP CHUTE BRAKET 废料滑槽支架SCRAP CHUTE HINGE 废料滑槽铰链SCRAP CONVEYER 废料传送装置SCRAP CUT 废料刀SCREW 螺钉SCREW PLUG 螺塞SECTION 剖面SEPARATE 剖切、分离SETTING BLOCK 调整块、镶嵌块（或限位块）SHADE OFF 逐渐变化、逐渐过渡SHUT HIGHT 闭合高度SIDE CURVE GAUGE 侧曲面型挡料器SIDE GAUGE 侧挡料器SIDE PIN 侧销SILENCER 消音器SINGLE ACTION DRAW 单动拉延SPARE BOX 备件盒SPARE PUNCH BOX 备用冲头盒SPECIAL SHAPE PUNCH 特殊形状的冲头SPEED CONTROLLER 速度控制阀SPRING CUSHION SET 弹性垫（缓冲器）SPRING LIFTER 弹簧顶升器SPRING PLUNGER 弹簧芯柱SPRING WASHER 弹性垫圈SPLIT PIN 开口销SPOOL RETAINER 短管导圈S TART POINT 设计基准点S TART HEIGHT 基准高度STAY 支架、支柱STAINLESS DIMPLE SHUTE 不锈钢凸包型滑槽STEEL 钢，钢块7STOPPER PLATE 锁板（止片）STROKE 行程STUD BOLT 双头螺栓-------- SUBLIFTER 顶升部件SWING PAD URETHANE BLOCK 悬挂式聚氨脂压料器TAP ALLOWBLE LOAD螺接头允许载荷TIE STRAP PLATE 连接板TANKER 充气罐TANKER CYLINDER PIPING 充气缸管系TEE T型接头THRUST 推力TOWLINE BOLLARD 拖索系缆桩UNIVERSAL JOINT 万向接头UNLOAD 卸料（卸载）UPPER STEEL 上刀块URETHANE STOCK BLOCK 优力胶托块（缓冲器）URETHANE SPACER 聚氨脂隔片URETHANE STRIPPER UNIT 聚氨脂卸料器合件VIBRATOR 震荡器VIEW 视图VOLUTE GUARD COMPLATE 螺旋型防护装置全套WASHER 衬垫、垫圈、垫片WEAR PLATE 防磨板、导板WITNESS PUNCH 标据凸模φ100 AIR VENT CORE 通气孔型芯8检具图常见英语词汇ADJUST BOLT 调节螺栓ADJUST BRACKET 调节支架BASE 基准BACK UP 玻璃钢垫层BODY GAP 本体间隙BUSH 销套、衬套CASTER WHL 小脚轮CHECKING FIXTURE 检具C/H 协调孔（即定位孔）CLAMP 夹紧器CLAMP PLATE 夹紧器安装板CLAMP SPT 夹紧器支承座COVER——BASE 基准防护罩DATUM SURFACE 基准面ENZART 蝶形螺栓FRAME 骨架FLUSH GAUGE 齐平检测块HOLE GAP 孔间隙HOOK 挂钩定位销L/P SETMAIN BASE 主基准MAIN BODY 主体PIPE 管子PROTECT PLATE 防护板RESIN 树脂、可加工塑料RESIN BLOCK 树脂座STOPPER PLATE 限止块SUPT—CLAMP 夹紧器支座（SUPPORT）SUPT—EYE BOLT 有眼螺栓（环首螺栓）支座TEMPLATE 样板、卡板9ZERO PLATE 零面支承块0—SURFACE 零面3—GAP 3毫米间隙3---GAP SEPARATE 3间隙间隔1mm GAP SCRIBED 1毫米间隙（间隔）划线COLOR 颜色BLACK 黑色GREEN 绿色RED 红色WHITE 白色10。

模具专业术语英文

模具专业术语英文

模具专业术语英文1. “Core Cavity（型芯型腔），嘿，就像房子的里里外外。

比如说做个塑料小盒子的模具，Core Cavity就决定了盒子的形状，是凹进去还是凸出来的部分，要是搞混了，哎呀，那做出来的盒子可就奇形怪状啦。

”2. “Gating System（浇口系统），这就好比是给模具‘输血’的通道呢。

想象一下你在浇花，那个浇花的水管就像是Gating System。

如果这个通道设计不好，就像水管堵住或者水流太大太小，那模具可就‘营养不良’或者‘撑坏’啦。

”3. “Ejection Mecha nism（顶出机构）。

哟，这可是模具里的‘小助手’呢。

就像从蛋糕模具里把蛋糕取出来得有个东西帮忙顶一下，在模具里，Ejection Mechanism就是干这个的。

要是没有它呀，那些成型的零件就只能卡在里面干着急喽。

”4. “Mold Base（模架），它可是模具的‘骨架’啊。

就像人没了骨架就瘫了一样，模具没了Mold Base那可就散架了。

比如说做个大的汽车零件模具，Mold Base要是不结实，整个模具能行吗？肯定不行呀。

”5. “Runner（流道），这就像小河流一样。

塑料或者金属材料就像河水在这个‘小河’里流动。

要是Runner设计得弯弯曲曲的，就像河流里到处是石头和弯角，那材料流动起来磕磕绊绊的，能做出好的模具产品吗？我看悬。

”6. “Draft Angle（脱模斜度），嘿，这个很重要呢。

这就像是给模具里的零件一个小斜坡，方便它们‘走出来’。

你想想，如果没有这个小斜坡，就像把东西硬塞进一个严丝合缝的盒子里，再想拿出来可就难喽。

”7. “Cooling Channel（冷却通道），它就像模具的‘空调’。

比如说你在夏天干活，没有空调热得受不了。

模具在工作的时候，如果没有Cooling Channel来降温，那热得可就乱套了，可能会影响模具的精度和寿命呢。

”8. “Parting Line（分型线），这就像是模具的‘分界线’。

模具英语词汇.

模具英语词汇.

插头： connector plug 插座： connector socket 密封/封料： seal
三：运水： water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker
四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plat
file 锉刀 flange joint 凸缘接头 grinder 砂轮机 hammer 铁锤 hand brace 手摇钻 hatching 剖面线 hexagon headed bolt六角头螺栓 hexagon nut 六角螺帽 index head 分度头 jack 千斤 jig 治具
kit 工具箱
chipping 修整表面缺陷 clamp-off 铸件凹痕 collapse 塌陷 color mottle 色斑 corrosion 腐蚀 crack 裂痕 crazing 碎裂 deformation 变形 edge 切边碎片 edge crack 裂边 fading 退色 filler speak 填充料斑 fissure 裂纹 galling 毛边 glazing 光滑 gloss 光泽 grease pits 污斑 grinding defect 磨痕
（二）Mould Tool
制模工具词汇

模具常用语中英文对照

模具常用语中英文对照
storage block
限位柱
stop block
起吊孔
handing hole
起吊环
eyebolt
靠块
heel
脱料拉杆
spool
模座导正块
thrust heel
种类
中文名称
英文名称
中文名称
英文名称
零
件
类
耐磨片
wear plate
垫片
shim
压块
keeper
初始管位
first start pin
键槽
stripper
下模板
die plate
冲头
punch
凹模
die
零
件
类
浮块
lifter
浮料板
lifter plate
成型公
form punch
压料块
pressure pad
切边冲头
trim punch
刀口
trim steel
沉头孔
counter bore
冲孔入子
button
顶针
kick off / ejector
key slot
键
key
氮气弹簧
nitrogen spring
螺旋弹簧
coil spring
聚氨酯弹簧
urethane
导柱
guide post
导套
guide bushing
插针
pilot pin
插针套
pilot bushing
侧刃
french
传感器
sensor
销
dowel
螺丝
screw
拔牙

模具常用术语中英文对照

模具常用术语中英文对照

模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料# Cold Slag线切割Wire E.D.M轮廊Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting 装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位Leader Pin Location耐落胶Teflon Paste偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate 垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert 行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar 下模水口铁Lower Runner Bar 弹簧Spring水口勾针Sprue Puller Pin 顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring 喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch 斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing 针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹）Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模※※※※ction Mold 入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板A'plateB板B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High V olume Running Mold剖面图Cross Section模具结构Mold Construction 模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension 雕刻Engrave。

模具常用术语中英文对照

模具常用术语中英文对照

模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料# Cold Slag线切割Wire E.D.M轮廊Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting 装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位Leader Pin Location耐落胶Teflon Paste偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate 垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert 行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar 下模水口铁Lower Runner Bar 弹簧Spring水口勾针Sprue Puller Pin 顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring 喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch 斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing 针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹）Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模※※※※ction Mold 入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板A'plateB板B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High V olume Running Mold剖面图Cross Section模具结构Mold Construction 模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension 雕刻Engrave。

模具常用英文词汇

模具常用英文词汇

推板导住ejector guide 直导套 guide bush, straight[straight bushing] 带头导套 guide bush, straight {shoulder bushing} 推板导套 ejector guidebush[ejector bushing] 定位圈 Locating ring锥形定位件 mould bases locating elements复位杆 ejector plate return pin[push-back pin] 限位钉 stop pin[stop but ton] 限位块 stop block [stop pad] 定距拉杆puller[length]bolt 定距拉板 puller[limit]plate 成形推杆 forming ejector pin 圆柱头推杆 ejector pin with cylindrical head 带肩推杆 shouldered ejector pin 扁推杆 flat ejector pin 推管 ejector sleeve 推块 ejector pad 推件板 stripper plate 推杆固定板 ejector retainer plate ; 推板 ejection plate[elector plate] 连接推杆 ejector tie rod 冲裁间隙 blanking clearance 模具闭合高度 die shut height 压力机闭合高度 shut height Of press machine 冲模寿命die life 压力中心 center Of load 冲模中心center Of die 冲压方向 pressing direction 送料方向 feed direction 排样 blank layout 搭边scrap 进距 feed pitch 切边余量 trimming allowance 毛刺burr 冲裁力 blanking force 弯曲力 bending force 拉仲力drawing force 挤压力 extruding force 卸料力 stripping force 推件力 ejecting force 顶件力 kicking force 压料力 pressure plate force 压边力 black holder force 毛坯blank ;钣金设计中常用的其它术语扩孑L enlarge hole 自铆 self-chinching 全周压毛边 all round burr 平头拉钉 set-headrivet 表面处理finish 定位销dowel pin 挂钩hook 平头铆钉 closed-end rivet 焊接线weld line 塑料固定栓 fastener, plastic, push-type压合胶粘剂 pressure sensitive adhesive 尼龙绑带 tie wrap, nylon 五金件 hardware 泡棉静电导片 gasket, foam, emi 贴纸 labeling 铍铜静电导片 gasket, beck, emi 烤漆paint 圆头螺钉 button-head screw 电镀 plating 平头螺母nut flush 铭板 nameplate 平齐自铆flush, self-clinching 包装 packing 紧固螺丝fix screw 铁材零件 sheet metal parts 组装 assembly 塑料零件plastic parts 凹陷，顶针 sink mark 压边铆钉 open-end rivet 插孔jack弹簧螺丝caps 度 thick 文字,记号 charactor 半冲孑L spring slice 角 corner 基座 chassis 自锁螺母 nut self-clenching 承座 bracket 轴肘式铆接toggle lock 承架 horsi ng 卡尺 caliper 下盖base 打印字模stamp letter 去毛边deburr反面far side 中性层neutral plane正面inside 弯曲角bending angle下料blank(blanking) 弯曲线bending line ;去除remove 回弹spring back量具measuring tools 相对弯曲半径relative bending radius板规plate gauge 弯曲半径bending radius比例规proportional dividers 最小弯曲半径minimum bending radius标准规standard gauge 弯曲件展开长度blank length of bends齿轮规gear tooth gauge 拉伸系数drawing coefficient丁字尺t-square 胀形系数bulging coefficient分线规divider; dividers 翻孔系数burring coefficient钢尺steel rule 最小冲孔直径minimum diameter of piercing 工作量规working gauge 转角半径radius厚薄规feeler(gauge) 相对转角半径-relative adios ;角尺angle square 相对高度relative height角规angle gauge 相对厚度relative thinness金属卷尺metallic tape 凸模圆角半径punch radius卡尺calipers; caliper 凸模总长punch overall length亥U度尺graduation ruler 凹模圆角半径matrix radius块规gauge(block) 凹模总长matrix overall length量规gauge 排料孔直径relief hole diameter螺距规screw pitch gauge 分型面parting line螺纹千分尺screw micrometer 水平分型面horizontal parting line径千分尺micrometer inside caliper; inside micrometer 垂直分型面vertical parting line卡钳inside caliper 浇注系统feed system皮尺tape(/measure) 主流道sprue平面规surface gauge 分流道runner千分表dial indicator 浇口gate千分尺micrometer 直浇道sprue曲尺carpenters square 横浇道runner三角尺set square 溢流槽over flow well深度千分尺micrometer depth gauge; depth micrometer 直接浇口direct[spore]gate椭圆规ellipsograph 环形浇口ring gate夕卜径千分尺outside micrometer 轮辐浇口spoke[spider]gate夕卜卡钳outside caliper 点浇口pin-point gate隙规gap(/clearance) gauge 侧浇口edge gate线规wire gauge 盘形浇口disk [diaphragm]gate斜角规bevel square 潜伏浇口submarine[tunnel]gate游标卡尺vernier caliper 扇形浇口fan gate圆规compasses 护耳浇口tab gate折尺folding pocket measure(/ruler) 冷料穴cold-slug well直尺straight edge 溢料槽flash [spew]groove中心规centre gauge 排气槽(孔)vent(Of a mould)锥度规taper gauge 注射能力shot capacity组合角尺combination set 收缩率shrinkage其它用语OTHER 注射压力injection pressure圆角半径fillet radius 锁模力clamping[locking]force成形压力 moulding pressure 模压力 internal mould pressure [cavity pressure] 开模力 mould opening force 脱模力 ejection force 抽芯力 core-pulling 扌由芯距 core-pulling distance 最大开距 maximum daylight[open daylight] 投影面积 projected area 冲压加工 stamping(press working) 冲床Press 块ram 承块 bolster 冲压模具stamping die 剪应力 shear stress 抗剪强度 shear strength 模辊 die roll 切断加工cutting 分断力口工 parting 下料加下blanking 冲孔加工piercing 切边加工trimming 冲缺[]notching 冲切缝lancing 准下料加工half-blanking 准冲孔加工half-punching 舌U 光加工shaving 精密下料fine blanking 精整加工 finish blanking V 形弯曲 V — bending U 形弯曲 U — bending L 形弯曲 L — bendin9 O 形弯曲 0— bending Z 形弯曲 Z?bending 卷边加工curlin9 引伸加工drawing 深弓I 伸加工 deep drawing 浮压成形embossing 逆向引伸 reverse drawing 再引伸 redrawing 拉成形 stretch forming 冲锻成形 progressivecold forming 缩颈成形necking 冶间成形cold forming 鼓胀成形bulging 凸缘成形flanging 孑L 凸绿成形 hole flanging 管材液压成形 tubehydro forming双点冲床，两点压力机 two point press (金属)支撑板tie strap 基座 subplate 沉头孑L , 沉孑L counter bore 切断Cutting 分断parting 分切加工下料 blanking 冲孑 L piercing/punching 切边 trimming 冲缺口 notching 冲切缝lancing 准下料 half-blanking 舌U 光加工shaving 精密下料fine blanking 精整下料 finishblanking 突条成形beading 浮压成形embossing 肋条成形ribbing 鼓胀成形bluging 孔凸缘加工 hole flanging 锥皿成形deeping 卷边成形culing 凸缘成形flanging 压印加工coining 锻粗加工upsetting 压凹加工indenting 引缩加工ironing 旋锻加工swaging 定寸加工sizing刻印加工marking 侧向水平切边加工horizontal trimming侧向冲孔加工 cam piercing 单工序模single operation dies 复合模 compound dies级进模 progressive dies 无导向模openingdies 导板冲模 guide plate dies 导柱模 guide pillar dies 通用模 universal dies 专用模 dies for special purpose 自动模automatic dies 组合冲模combined dies 落料模 blanking dies 冲孔模 piercing dies 切边模 trimming dies 切口模 notching dies 剖切模parting整修模shaving dies 压印加工coining精冲模fine blanking dies 锻粗加工upsetting切断模cutting-off dies 引缩加工ironing弯曲模bending dies 旋锻加工swaging卷边模curling dies 定寸加工sizing扭曲模twisting dies 刻印加工marking拉伸模drawing dies 侧向冲孔加工cam plercing反拉伸模reverse redrawing dies 侧向水平切边加工horizontal trimming 变薄拉仲模ironing dies 中立面netural plance成形模forming dies 中立轴线netural axis胀形模bulging dies 胚料blank整形模sign dies 加热成形hot forming缩口模necking dies 引伸比drawing ratio扩口模flaring dies 弓丨伸率drawing rate翻边模flanging dies 成形极限forming limit翻孔模burring dies 引伸极限比limit drawing ratio冷挤压模cold extruding dies 成形极限图forming limit diagram正挤压模forward extruding dies 液压成形hydro forming反挤压模backward extruding dies 挤制加工extruding复合挤压模compound extruding dies 回弹spring back径向挤压模radial extruding dies 压延方向roll direction简易模low-cost dies 降伏点yield point橡胶冲模rubber-dies 降伏应力yield stress钢带模steel rule dies; 调质压延skin pass低熔点合金模low-melting point alloys dies 矫直加工straighting(1eveling)锌基合金模zinc based dies 加工硬化值n value薄板模laminated dies 冲头punch塑料成形模具mould for plastics 冲孔冲头piercing punch热塑性塑料模mould for thermoplastics 下料冲头blanking punch热固性塑料模mould for thermosets 弯曲冲头bending punch压缩模compression mould 成形冲头forming punch压注模transfer mould 弓丨伸冲头drawing punch注射模injection mould 模块die block热塑性塑料注射模injection mould for thermoplasties 整块式模块solid die block热固性塑料注射模injection mould for thermosets 窝座式模块socket die block溢式压缩模flash mould 共轭式模块yoke die block半溢式压缩模semi-positive mould 镶入式模块insert die block不溢式压缩模positive mould 模具die(tOO1) ?移动式压缩模portable compression mould 冲切模具cutting die(tOO1)移动式压注模portable transfer mould 下料模具blanking die(tOO1)固定式压缩模fixed compression mould 冲孔模具piercing die(tOO1)固定式压注模fixed transfer mould 弯曲模具bending die(tOO1)无流道模runner less mould 成形模具forming die(tOO1)热流道模hotrunner mould 引仲模具drawing die(tOO1)温流道模warm runner mould 复合模具compound die(tOO1)压力铸造模具die-casting die 连续模具progressive die(tOO1)模架die sets 精密下料模具fine blanking die(tOO1)弹压导板模架die sets with spring guide plate 传送模具transfer die(t001)后导柱模架back pillar[post]sets 模具寿命die(toot)life对角导柱模架dia gonal pillar[post]sets 卷材coils中间导柱模架center pillar[Post]sets 模具闭合高度die shut height精冲模架fine blanking die sets 送料高度feeding height(pass line) 滑动导向模架sliding guide die sets 材料利用率yield ratio滚动导向模架anti-friction bearing die sets 滚轮式送料机roller feeder通用模架universal die sets 夹送式送料机grip feeder标准模架standard mould bases 空气式送料机air feeder工作零件working elements 凸轮式送料机cam feeder定位零件locating elements; 模具缓冲器die cushion压料卸料零件elements for clamping and stripping 脱料板（压料板）stripper导向零件guide elements 固定式脱料板fixed stripper固定零件retaining elements 可动式脱料板movable stripper凸模punch 整块式脱料板solid stripper凹模matrix 多件式脱料板multi stripper凸凹模punch-matrix 镶入式脱料板insert stripper镶件insert 快速换模quick die change拼块section 多工程模具multi —station die 定位销locating[gauge]pm 单上程模具single station die定位板locating plate 模座die set挡料销stopping 上模座upper die set导正销pilot pin 下模座lower die set导料板stock guide rail 导柱guidepost定距侧刃pitch punch 导套guide bush侧刀挡块stop block for pitch punch 顶出具ejector始用挡料销finger stopping block 顶出销ejector pin侧压板side-push plate 辅助导柱sub guidepost限位块limited block 辅助导套sub guide bush限位柱limited post 等高块stopper卸料板stripper plate 冲头固定板punch plate推件块ejector 升料销（顶料销）lift pin推杆ejector pin 下模固定板die plate推板elector plate 凸轮cam连接推扌千ejector tie rod 先导杆（导冲）pilot pin打杆knockout pin 误送检知器misfeeder顶件块kicker 极限开关limit switch顶杆kicker pin 导料板guide plate卸料螺钉stripper bolt 导料块guide block拉杆tie rod 导料销guide pin托杆pressure[cushion]pin 模具单边间隙die clearance托板supporting [Pressure]plate 弓丨伸率drawing rate废料切断刀scrap cutter 桥带bridge弹顶器cushion 边系带carrier承料板stock supporting plate 压力销pressure pin压料板pressure plate 模柄die shank压边圈blank holder 定位销dowel pin齿圈压板serrated ring 导柱 guide pillars[post] 导套 guide bushes 导板 guideplate 滑板 slide plate 耐磨板wear plate 弹压导板 spring guide plate 钢球保持圈 cage 上模座 punch holder[upper shoe] 下模座 die holder [low shoe] 凸模固定板punch plate 凹模固定板matrix plate 垫板 backing plate 侧型芯side[slide]core 螺纹型芯 thread plug[threaded core] 螺纹型环 threading[threaded cavity] 嵌件 insert(for moulding) 浇口套 sprue bush[sprue bushing) 分流锥spreader 加料腔 loading chamber [transfer pot] 柱塞 force[pot ]plunger 拉料杆 sprue puller 钩形拉料杆 sprue puller, z-shaped 球头拉料杆 sprue puller ball headed 圆锥头拉料杆 sprue puller ,conical headed 分流道拉料杆 runner puller[runner lock pin] 支承柱 support pillar 支架 ejector housing[mould base leg] 斜销 angle pin [finger cam] 滑块 slide[camslide 滑块导板 slide guide strip楔紧块 heel[wedge]block 弯销 dog-leg cam. 斜块 angled-lift splits带头导柱 guide pillar, straight[straight leader pin] 带肩导柱 guide pillar,shouldered[shoulder leader pin]上模背板 punch backing plate 下模背板 die backing plate 脱料板背板 stripper backingplate 踢出销 kicker pin 吊钩hook 固定螺丝setscrew 后跟块heel block 毛头(毛边、毛刺)burr 料条布置strip layout 胚科布置blank layout 空坫 idle stage 切缝lance 砂漏形切缝 hourglass lance 圆形切缝 circular lance 送料节距feed pitch 直接导引direct pilot 间接导引 indirect pilot 胚料布列blank layout 侧边冲切side cut 有限元素法 finite element method 线架构wire frame 刀具路径tool path 材料清单 bill ofmaterial 计算机辅助设计 Computer Aided Design(CAD/ 计算机辅助制造 Computer Aided anufacture(CAM) 后处理 postprocessor 直艘数值控？ Direct Numerical Control(DNC) 计算机数值控制 Computwer Numerical ontrol(CNC) 人工程序设计 manual programming 自动柱式设计 automatic programming 表面模型surface model 实体模型so1id model 垫板 shimplate 墊片 backup plate 平垫圈 flat washer组装专业词汇Assembly line 组装线 Layout 布置图 Conveyer 流水线物料板 Rivet table 拉钉机 Rivet gun 拉钉枪 Screw driver 起子 Electric screw driver电动起子 Pneumatic screw driver气动起子front plate前板rear plate 后板 chassis |'/?si| 基座bezel panel 面板 power button 电源按键 reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS电源电压接柆键 SOP 制造作业程序T-slot T 形槽 tool for lathe 车刀 tool point angle 刀刃角 tool post 刀架 tosecan 划线盘 trimming 去毛边 waffle die flattening 压纹效平wiper 脱模钳 wrench 螺旋扳手 analog-mode device 类模器 die lifter 举模器 argon welding 氩焊 pedal 踩踏板 stopper 阻挡器 flow board 流水板 hydraulic handjack油压板车 forklift 叉车 pallet 栈板 glove(s)手套 glove(s) with exposed fingers 割手套 thumb 大拇指 forefinger 食指 midfinger 中指 ring finger 无名指worktable 工作桌 OOBAf 箱检查 fit together组装在一起fasten 锁紧（螺丝） fixture 夹具（治具） pallet 栈板 barcode 条形码 barcode scanner 条形码扫描仪fuse together 熔合 fuse machine 热熔机 repair 修理 operator 作业员QC 品管 supervisor 课长 ME 制造工程师 MT 制造生技 cosmetic inspect夕卜观检查inner parts inspect 部检查 thumb screw 大头螺丝 lbs.inch 镑、英寸 EMI gasket 导电条material check list 物料检查表 work cell 工作间 trolley 台车 carton 纸箱 sub-line 支线 left fork 叉车 personnel resourcedepartment 人: production department生产部门planning department 企划部 QC Section 品管科 common equipment 常用设备 uncoiler and straightener 整平机 to move, to carry, to handle搬运be put in storage 入库 pack packing 包装 to apply oil 擦油 to file burr锉毛刺final inspection 终检 to connect material接料 to reverse material翻料alcohol container 沾湿台 head of screwdriver 起子头 sweeper 扫把 mop 拖把vaccum cleaner 吸尘器 rag 抹布 garbage container 灰箕 garbage can 垃圾箱 garbage bag 垃圾袋 chain 链条 jack 升降机 production line 流水线 chain 链条槽 magnetizer 力口磁器 lamp holder 灯架 to mop the floor 拖地 to clean thefloor 扫地 to clean a table 擦桌子 air pipe 气管 packaging tool 打包机 packaging 打包 automatic screwdriver 电动启子 thickness gauge 厚薄规 gauge(orjig) 治具little finger 小指power wire 电源线band-aid创可贴buzzle蜂鸣器iudustrial alcohol 工业酒精。

模具专业英语词汇

模具专业英语词汇

ＩnjectiｏｎMｏｌd Techniｃal Terms（一)模具专业基本用词Ｐroｆessional Tｅrｍs1．塑料 - ｐlastiｃ，rｅsｉn2．样件—sample3．钢料—sｔeel4．注塑机—injection machine，pｒess5．产品—parｔ，product，ｍouｌding6．模具 - molｄ，ｍould，ｔoolA 简易模(样板模)—pｒｏtotype moｌdB 量产用模具—ｐroduction mold 7．三维造型（数模）—3D model，3D ｄａｔa8．二维产品图—2D pａrt drａｗｉng9．设计- desｉgｎ10．制造—maｎufactｕrｅ, builｄｕp，conｓｔrｕctｉon11．检验—cｈecｋ，iｎsｐectｉｏn12．测量—measｕre，inspection13．修改 - cｈaｎgｅ，modify,ｃｏrrecｔion14．工程更改 - enginｅer change15．质量—quａlｉty16．数量—quantitｙ17．基准 - daｔum，referenｃe牛角入水—ｒads gate(二)如何解析2Ｄ产品图？How ｔｏread 2D part drawing?一．产品几何Geomｅtry1．点—poｉnt２．线（边) —line, ｅｄｇe3．面faceA 侧面—ｓiｄｅB 表面 - sｕrfaceC 外观面—appearaｎce sｕｒfａce４。

壁厚—waｌｌtｈicｋnｅss, stoｃk thicknesｓ5.加强筋（骨位）—ｒｉb6。

孔 - ｈolｅ７。

细长得槽—sｌot８。

柱位—ｂｏss9．角—cornerＡ圆角—fiｌｌet B 倒角—cｈamfeｒ C 尖角—ｓhａrp cｏrner10。

斜度—angｌe,taper11、凹槽—rｅcｅss, ｇroove二．分模信息Splｉtting1．分型线 - pａrｔiｎｇline (P／L)，sｐｌittinｇliｎe2．主分模方向—ｍain diｒectioｎ，line oｆdｒaw3．浇口设定—gating产品标识Part Identifｉcaｔｉon1．产品名称—pａｒt namｅ(P／N）2．产品编号+版本号 - part ｎｕmber + reｖｉsioｎ(Reｖ、)3．型腔号 - cavｉty nｕmber4．材料标记—ｍaterｉaｌsyｍbol5．模具编号—ｍold ｎumbｅｒ（nｏ、）6．日期印 - daｔing insert，daｔeｃode7．循环印—ｃyｃlｉnｇcoｄｅ8．公司标志- paｎy logo三．技术要求Specifiｃaｔioｎ(Specｉal Reqｕirement）1．项目启动表Ｋiｃk—ｏff sheet1）项目名称—ｐrogrａm name，ｐroject nａme2）产品名称—part name, proｄuct name，pａｒt dｅsｃrｉptioｎ3）产品编号—part ｎumbｅr （P/Ｎ)4）客户模号—custｏmer moｌd nｏ、5）项目启动日期—kick ｏff date，ｓｔarｔｄate6）项目完成日期 - due date，leａｄｔimｅ7）内模件用钢 - tｏol steｅl8）型腔数量 - ｎumber of caｖitieｓ9）数据文件编号—ｄata 、10）注塑材料—rｅｓin，plastic, raw materiａl11）收缩率 - shriｎk，shｒinkage，shrｉnk factｏr12）注塑机吨位 - molｄingｍachiｎｅsize，iｎjection ｍacｈｉneｓize 13）成型周期- cyｃle tｉme14）型腔光洁度—caｖity poliｓh15）型芯光洁度—core poｌiｓｈ16）皮纹（晒纹）—ｔextuｒｅ,grain17）拔模斜度—draft ａｎgｌｅ，rｅｍovaｌｔaｐｅr18）注塑件颜色及光泽—molｄed ｃolｏr ＆gloss19）模具加工地 - manufacｔｕrinｇｆaｃility20）热流道供应商—manifold manufacturｅr，manifoｌd supplier21）浇口位置- gate locaｔioｎ/pｏsｉｔion22）浇口类型- gate type23）产品标识—ｓtamｐinforｍａtion，parｔidenｔificatiｏn24）特殊要求- special insｔrｕctioｎs25）安全模数—ｓafeｓtｅeｌ2．产品质量及外观要求ParｔQualitｙ＆Appeaｒance Requirｅmｅnt1）尺寸及公差Dｉmensｉon & Toleｒaｎce①重要尺寸—criｔical dｉmensiｏn，imｐortant dim、，key dim、②理论尺寸—ｎominaｌｄiｍｅnsion③实际尺寸—ａcｔｕal dimension④公差—toｌeraｎce⑤公差带—ｔｏｌeｒance rａnge⑥尺寸超差—dimeｎsioｎdeｖiａｔion⑦接受(合格)-acｃept，ＯK⑧拒绝(不合格) —ｒeject, refuse,ｏbsolｅte，NG⑨让步接受- concessiｏn，sｐeciａl adｍit⑩返工—ｒe-work2）产品缺陷(常见得)Defeｃts （noｒｍal)①缩水—sinｋｍａrk，ｓhｒｉnkａgｅ②飞边，毛边—fｌaｓh,burr③段差—ｍisｍａtch dｉscｒepａncｙ④银丝纹,蛇纹—ｓnａke mａrｋs，streaｋ⑤弯曲,变形—warpage, distoｒtion⑥打不饱（缺料）—shｏrt shｏｔ⑦熔接线—weld lｉne⑧多胶—unwanted plastｉc⑨拉伤—ｄamage3．产品外观Part Appearanｃe①产品颜色—parｔcolor②产品光泽—gloss③皮纹粒度—ｇrain4．常用词汇、词组及短语Ｎoｒmａl Wｏrd，Short Sentence1）单边—peｒsｉdｅ2）双边 - ｂotｈsｉdes3）加入,添加-aｄd,incｏrporａｔe4）去除,取消—rｅｍovｅ，caｎcel5）满足…得要求，符合，与…要求一致—acｃordiｎg tｏ,ｃoｎｆormｔo，ｓatｉｓｆy,meet6）要求，需要—requｉre，ｎeｅd，demaｎd7）确认—be ａpｐrｏved，agｒeed by…8）允许—permit，ａllｏｗ9）在…范围之内—ｗｉｔｈｉｎ10）不可以,不允许，禁止—free from，prｅvｅnt，ａvoｉd11）…,除非有另指—…unｌeｓs otｈeｒwise speｃifiｅd12）…或少于—…or lｅss13）自动化运作—ａｕtｏmatｉｃｏperaｔion14）未注尺寸(详细形状)见三维造型Ｎoｎdimensioned contoｕr(ｄｅｔaｉｌed shａpe）see3D mｏdel、15）分型线上得飞边（披缝)或段差应小于…Ｂuｒｒｓor diｓｃｒｅpａncｙoｎthｅP／L shall be …or lｅｓs、四．标题栏TitleＢｌock1．产品名称—ｐarｔnaｍe2．图纸编号+ 版本号（索引号）- drawing no、+ｌｅvel （indｅｘ）3．一般公差—ｇｅneｒal tolｅrance(三) 如何阅读制模标准？Hoｗｔｏrｅad tooliｎｇstandard？一.模具结构术语Mold ConsｔrｕctｉoｎTermsＡ。

常用模具英语单词

常用模具英语单词

die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品bolt螺栓模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner, hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainer plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate 压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode模具零件：mold components三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin顶针板：ejector retainner plate 托板：support plate螺丝：screw 管钉：dowel pin开模槽：ply bar scot 内模管位：core/cavity inter-lock顶针：ejector pin 司筒：ejector sleeve司筒针：ejector pin 推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）：mold base 上内模：cavity insert下内模：core insert 行位（滑块）：slide镶件：insert 压座/斜鸡：wedge耐磨板/油板：wedge wear plate 压条：plate撑头: support pillar 唧嘴：sprue bushing挡板：stop plate 定位圈：locating ring锁扣：latch 扣鸡：parting lock set推杆：push bar 栓打螺丝：S.H.S.B顶板：eracuretun 活动臂：lever arm分流锥：spure sperader 水口司:bush垃圾钉：stop pin 隔片：buffle弹弓柱：spring rod 弹弓:die spring中托司：ejector guide bush 中托边：ejector guide pin镶针：pin 销子：dowel pin波子弹弓：ball catch模具成形不良用语英汉对照aberration 色差atomization ?化 bank mark ?料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜low hole 破孔blushing 泛白body wrinkle 侧壁皱纹 breaking-in 冒口带肉bubble 膜泡burn mark 糊斑 burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱 check 细裂痕check ing 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹各式模具分类用语英汉对照landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模各种模具常用成形方式英汉对照accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模。

模具常用语中英文对照

模具常用语中英文对照
压边圈
binder
弹簧箱顶板
spring—box eject—plate
公
差
类
公差
tolerance
公差范围
tolerance range
上公差
upper tolerance
下公差
lower tolerance
公差+/- 0.05
plus minus 0。05
形位公差图
GD&T
平面度
flatness
吨位
tonnage
行程
stroke / travel
冲床上台面
ram
冲床下台面
bolster
冲床台面布置图
press layout
冲床上的快速对正
QDC
冲床气垫
air cushion
码仔
stirrup
闭合高度
shut height
T型槽
T-slot
送料机
feeder
送料高度
feeding height
X：-￠0.00（合销孔,钻穿)
X：-￠0.00（DR。THRU FOR DOWEL）
X:-￠0。00(一般孔,钻穿）
X:—￠0.00 (DR.THRU HL）
X：-￠0。00（穿丝孔,钻穿)
X:—￠0。00 (DR。THRU FOR WEDM S。H。)
X:-￠0.00（漏油孔,钻穿)按向视图加工
storage block
限位柱
stop block
起吊孔
handing hole
起吊环
eyebolt
靠块
heel
脱料拉杆
spool
模座导正块

模具常用术语中英文对照

模具常用术语中英文对照

模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料# Cold Slag线切割Wire E。

D.M轮廊Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick—Off Meeting 装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2—13Tap 导柱位Leader Pin Location耐落胶Teflon Paste偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate 垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut—Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub—Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机) Jaw硬片(摩擦片) Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar下模水口铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball—Catch斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A’PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing 针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈(法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide—In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3—Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹）Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花(擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模※※※※ction Mold 入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板A'plateB板B’plate倒扣Under—Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫(限螺丝）Stripper Bolt 盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料＃Cold Slag线切割Wire E。

  1. 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

模具图中常见英文词语ADAPTER 管接头ADHESIVE GLUE 粘结剂AIR CYLINDER 气缸AIR PIPING SET 空气管路装置AIR VENT TUBE 空气排气管AIR VENT TUBE （COPPER）空气排气管（铜管）AIR VENT TUBE （NYLON）空气排气管（尼龙管）BACK UP KEY止退键BACKUP 止退5°BACK5°负角BEAD 拉延筋BELL CRANK LIFTER SET 曲柄顶升机构BLANCER PLATE 平衡块BLANK DIE 落料模BLANKHOLDER STOPPER BOLT 压边圈限位螺钉BLANCER BLOCK 平衡块BOSS HOOK 铸造吊柄BOTTOM BLOCK 压靠块BOTTOM DIE 凹模镶套BOTTOM MARKE 到底标记BOTTOM PLATE 到底块、镦靠块BOLSTER SIZE （压机）工作台尺寸B/H （BLANK HOLDER ）压边圈BOL T 螺栓BOL T TYPE HOOK 螺栓型吊钩BUSING 套管C/HCAM BOTTOM GUIDE PLATE 斜楔底部导向板CAM BOTTOM SLIDE PLATE 斜楔底部滑板CAM DIE 斜楔模CAM PAD KEEPER 斜楔压料器保位装置CAM POSITIVE RETURN FOLLER 斜楔刚性回程随动器CAM RETURN PLATE 斜楔回程板CAM RETURN UNIT 斜楔返回装置CAM SLIDE 斜楔滑板CAM SPRING UNIT 斜楔弹簧组合件CAM STOPPER 斜楔限止器CAM STROKE PLATE 斜楔行程楔块CASTING DIMENSIONS 铸造尺寸CHECKING FIXTURE 检具CAST IN NUT 铸入式螺母CAST IN HOOK 铸入式挂钩CAST IN LIFTING BUSH 铸入式起重衬套CAST IN PIPE 铸入式导管COIL SPRING 卷形弹簧COIL SPRING GUIDE 弹簧导销COLLAR 杆环（轴环、垫圈等）CONTROL PANEL 控制板COTTER PIN 开尾销COUPLING NUT 联接螺母COUPLING PLATE 联接板COUPLING SLEEVE 联接套COVER 防护罩CUT SECTIONAL 分段切割(废料刀分布)DIE 模具DATUM LINE 基准线DIFFERENCE ELBOW 差异式管接头（不等径）DIFFERENCE SOCKET 差异式管接座（不等径）DISTANCE BLOCK 定距块（等高块）DOUBLE ACTION DRAW 双动拉延DOWEL PIN 销DETAIL 放大DCP（DIE CHECK POINT）模具检测点DIRECTION OF FEED 送料方向ECONOMY REAR GAUGE 经济型后挡料器EJECTOR 顶出装置ELBOW 弯管接头ELECTRISTIC PARTS 电器部件EMBOSS（PUNCH INSERT）压印、压凸点（凸模镶嵌件）FASTENING SLOTS固定槽F EED 送料FINAL PRESSURE 最终压力FLANGE DIE 翻边模FLANGE LIFTER 翻边顶升器FLANGE LIFTER BLOCK 翻边顶升器顶升块FLANGE LIFTER GAUGE BLOCK 翻边顶升器挡料块FLANGE LIFTER PUSH PIN 翻边顶升器推销FL YING 飞行式（吊装式斜楔）FOME 成形FRONT GAUGE 前挡料板GAS SPRING 氮气弹簧GAS SPRING MOUNTING 氮气弹簧固定件GAS SPRING HOSE SYSTEM斥氮气弹簧管道系统GAUGE 测量、量规、样板GUARD 防护装置GU IDE PIN 导向销GUIDE POST 导向柱GUIDE BUSH 导向衬套GUIDE BAR 导板GUIDE ROLLER 导向滚轮HARCROSS LIFTERHAND VALVE 换向阀HEADER BLOCK 管接头集成块H EEL 跟部HEM DIE 包边模HEX NUT 六角螺母HEX BOLT 六角螺栓HOLE SET PLUG 孔塞头HOLDER PLATE 托板HOOK 挂钩HOOK PIN 挂销HORIZONTAL DATUM LINE 水平基准线HOSE CLAMP 软管夹HOSE JOINT 管接头HEXAGON NUT 六角螺母INCLINED 倾斜式INCLINATION REAR GAUGE 倾斜式（偏翻式）后挡料器INR SLIDER 内滑块INR HEIGHT 内模高度INSERT 镶嵌件INITIAL PRESSURE 最初压力JECTOR PUNCH顶料凸模KEY 键KEEPER 保位物KEEPER PLATE 限位块LATCH LIFTER 碰锁式提升装置LIFTER 升降器LIFTING LOAD 顶升载荷LIMIT SWITCH 行程开关（终端开关）LOAD 装料（装载）LOADING STAY 重量支撑、限止器LOCATING CONE 定位锥LOCATION KEY 定位键LOCATION PIN 定位销-LOCK BEAD 拉延槛LOCK NUT 锁紧螺母LOCKER CHAIN 链条LOWER STEEL 下刀块MCS(MASTER CONTRL SURFACE)主控面MAGNET 磁铁OTR SLIDER 外滑块OTR RISER 外垫板NEST GUIDE导向套NIPPLE 螺纹接头NUT 螺母NYLON TUBE 尼龙管PAD 压料芯PANEL CHUTE 板料滑槽（板料装卸托架）PIERCE DIE 冲孔模PIERCE PUNCH（BALL LOCK TYPE）冲孔凸模（球锁紧）PIERCE PUNCH（SHOULDER TYPE0 冲孔凸模（台肩式）PIERCE PUNCH（LIGHT DUTY）冲孔凸模（轻载荷）PIERCE PUNCH（HEA VY DUTY）冲孔凸模（重载荷）PIN TYPE GAUGE 销式挡料器PIN TYPE HOOK 销型吊钩（起重棒）PLAIN WASHER 垫圈--------PLAN VIEW OF LOWER DIE 模具下平面图PLATE TYPE HOOK 板式吊钩PLATE TYPE GAUGE 板式挡料器PLUG 插头PNL IMPUT DETECOR 板件到位探测器POSITIVE RETURN 刚性回程装置（确定回位）PROGRESIVE DIE 连续模PUNCH 凸模PUNCH PROFILE 凸模轮廓线PUNCH RETAINER 凸模固定座（保持器）PUNCH WITH CENTER HOLE 带中心孔的冲头PUSH PIN 推销PUSHER 推进器QUICK EXHAUST VALVE快速排气阀RACK 齿条REGULAR PUNCH 固定冲头RESTRIKE DIE 整形模R ETAINER BOLT 卸料螺钉、止动螺钉RETAINER PIN 导销RIB 肋RING BOLT/HOOK 环形吊钩REQUIRE PRESSURE 要求压力ROLLER CARRIER 滚动式传送器ROUGH GUIDES 粗导向器ROUGH TRIM 粗修边RUBBER ROLLER 橡胶滚轮SAFETY AREA 安全区域SAFETY BLOCK 安全块（或保险块）SAFETY BLOCK FOR STORAGE 存放装置SAFETY COVER 防护罩SCRAP BOX 废料盒SCRAP BOX GUIDE 废料盒导向板SCRAP BREAKER 废料破碎装置SCRAP CHUTE 废料滑槽SCRAP CHUTE BRAKET 废料滑槽支架SCRAP CHUTE HINGE 废料滑槽铰链SCRAP CONVEYER 废料传送装置SCRAP CUT 废料刀SCREW 螺钉SCREW PLUG 螺塞SECTION 剖面SEPARATE 剖切、分离SETTING BLOCK 调整块、镶嵌块（或限位块）SHADE OFF 逐渐变化、逐渐过渡SHUT HIGHT 闭合高度SIDE CURVE GAUGE 侧曲面型挡料器SIDE GAUGE 侧挡料器SIDE PIN 侧销SILENCER 消音器SINGLE ACTION DRAW 单动拉延SPARE BOX 备件盒SPARE PUNCH BOX 备用冲头盒SPECIAL SHAPE PUNCH 特殊形状的冲头SPEED CONTROLLER 速度控制阀SPRING CUSHION SET 弹性垫（缓冲器）SPRING LIFTER 弹簧顶升器SPRING PLUNGER 弹簧芯柱SPRING WASHER 弹性垫圈SPLIT PIN 开口销SPOOL RETAINER 短管导圈S TART POINT 设计基准点S TART HEIGHT 基准高度STAY 支架、支柱STAINLESS DIMPLE SHUTE 不锈钢凸包型滑槽STEEL 钢，钢块STOPPER PLATE 锁板（止片）STROKE 行程STUD BOL T 双头螺栓-------- SUBLIFTER 顶升部件SWING PAD URETHANE BLOCK 悬挂式聚氨脂压料器TAP ALLOWBLE LOAD螺接头允许载荷TIE STRAP PLATE 连接板TANKER 充气罐TANKER CYLINDER PIPING 充气缸管系TEE T型接头THRUST 推力TOWLINE BOLLARD 拖索系缆桩UNIVERSAL JOINT 万向接头UNLOAD 卸料（卸载）UPPER STEEL 上刀块URETHANE STOCK BLOCK 优力胶托块（缓冲器）URETHANE SPACER 聚氨脂隔片URETHANE STRIPPER UNIT 聚氨脂卸料器合件VIBRATOR 震荡器VIEW 视图VOLUTE GUARD COMPLATE 螺旋型防护装置全套W ASHER 衬垫、垫圈、垫片WEAR PLATE 防磨板、导板WITNESS PUNCH 标据凸模φ100 AIR VENT CORE 通气孔型芯检具图常见英语词汇ADJUST BOLT 调节螺栓ADJUST BRACKET 调节支架BASE 基准BACK UP 玻璃钢垫层BODY GAP 本体间隙BUSH 销套、衬套CASTER WHL 小脚轮CHECKING FIXTURE 检具C/H 协调孔（即定位孔）CLAMP 夹紧器CLAMP PLATE 夹紧器安装板CLAMP SPT 夹紧器支承座COVER——BASE 基准防护罩DATUM SURFACE 基准面ENZART 蝶形螺栓FRAME 骨架FLUSH GAUGE 齐平检测块HOLE GAP 孔间隙HOOK 挂钩LOC.PIN 定位销L/P SETMAIN BASE 主基准MAIN BODY 主体PIPE 管子PROTECT PLATE 防护板RESIN 树脂、可加工塑料RESIN BLOCK 树脂座STOPPER PLATE 限止块SUPT—CLAMP 夹紧器支座（SUPPORT）SUPT—EYE BOLT 有眼螺栓（环首螺栓）支座TEMPLATE 样板、卡板ZERO PLATE 零面支承块0—SURFACE 零面3—GAP 3毫米间隙3---GAP SEPARATE 3间隙间隔1mm GAP SCRIBED 1毫米间隙（间隔）划线COLOR 颜色BLACK 黑色GREEN 绿色RED 红色WHITE 白色。

相关文档
最新文档