管道,风管,排水,燃料专业英语词汇
管道类术语英汉对照及名词解释
2 一般部分2.1 配管piping 按工艺流程、生产操作、施工、维修等要求进行的管道组装。
2.2 公称直径nominal diameter 表征管子、管件、阀门等口径的名义内直径。
2.3 公称压力nominal pressure 管子、管件、阀门等在规定温度下允许承受的以压力等级表示的工作压力。
2.4 工作压力working pressure 管子、管件、阀门等在正常操作条件下承受的压力。
2.5 设计压力design pressure 在正常操作过程中①,在相应设计温度下，管道可能承受的最高工作压力。
2.6 强度试验压力strength test pressure 管道强度试验的规定压力。
2.7 密封试验压力(严密性试验压力)sea1 test pressure 管道密封试验的规定压力。
2.8 工作温度working temperature 管道在正常操作条件下的温度。
2.9 设计温度design temperature 在正常操作过程中①，在相应设计压力下，管道可能承受的最高或最低温度。
2.10 适用介质suitable medium 在正常操作条件下，适合于管道材料的介质。
3 管子与管道3.1 管子pipe 一般为长度远大于直径的圆筒体，是管道的主要组成部分。
3.2 管道(管路)piping (pipe line) 由管子、管件、阀门等连接成的，输送流体或传递流体压力的通道口。
3.3 管道系统（管系）piping system 单独一组设计条件相互联系的管道。
3.4 管道组成件piping components 连接或装配成管道系统的元件，包括管子、管件、法兰、阀门、支撑件以及补偿器等。
3.5 管子表号pipe schedule number 工作压力与工作温度下的管子材料许用应力的比值乘以一个系数，并经圆整后的数值，是表征管子壁厚系列的代号。
3.6 无缝钢管seamless steel pipe 钢坯经穿孔轧制或拉制成的管子，以及用浇注方法制成的管子。
管道常用的英文单词
绝好的网址(下面没有粘贴完) 1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔(弧)焊钢板卷管electric-fusion (arc)-welded steel-plate pipe 螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbowk半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头(右向或左向)side outlet elbow (right hand or left hand)双支管弯头(形)double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通(右向或左向)side outlet tee (right hand or 1eft hand)异径三通(分支口为异径)reducing tee (reducing on outlet)异径三通(一个直通口为异径)reducing tee (reducing on one run)带支座三通base tee异径三通(一个直通口及分支口为异径)reducing tee (reducing on one run and outlet)异径三通(两个直通口为异径,双头式)reducing tee (reducing on both runs, bull head) 45°斜三通45° lateral45°斜三通(支管为异径)45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run)45°斜三通(一个直通口及支管为异径) 45° lateral (re ducing on one run and branch)Y型三通(俗称裤衩)true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通(一个分支口为异径)reducing cross (reducing on one outlet)异径四通(一个直通口及分支口为异径)reducing cross (reducing on one run and outlet)异径四通(两个分支口为异径)reducing cross (reducing on both outlet)异径四通(一个直通口及两个分支口为异径)reducing cross (reducing on one run and both outlet)异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台,插入式支管台boss管接头coupling, full coupling半管接头half coupling异径管接头reducing coupling活接头union内外螺纹缩接(俗称补芯)bushing管帽cap (C)堵头plug短节nipple异径短节reducing nipple; swage nipple 1.3 弯管Bend预制弯管fabricated pipe bend跨越弯管(^ 形)cross-over bend偏置弯管(~ 形)offset bend90°弯管quarter bend环形弯管cirele bend单侧偏置90°弯管(? 形)single offset quarter bend S形弯管“S” bend单侧偏置U形膨胀弯管(| ?形)single offset “U” bend U形弯管“U” bend双偏置U膨胀弯管double offset expansi on “U” bend 斜接弯管mitre bend三节斜接弯管3-piece mitre bend折皱弯管corrugated bend圆度roundness1.4 法兰Flange (FLG)整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰(包括平焊法兰)slip-on flange (SO); slip-on welding flange 承插焊法兰socket welding flange松套法兰lap joint flange (LJF)对焊法兰welding neckflange (WNF)法兰盖blind flange, blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange对焊环welding neck collar (与stub end相似)平焊环welding-on collar突缘短节stub end, lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating, pressure rating class压力—温度等级pressure-temperature rating法兰密封面,法兰面flange facing突面raised face (RF)凸面male face (MF)凹面female face (FMF)榫面tongue face槽面groove face环连接面ring joint face全平面;满平面flat face; full face (FF)光滑突面smooth raised face (SRF)法兰面加工facing finish粗糙度roughness光滑的smooth齿形serrated均方根root mean square (RMS)算术平均粗糙高度arithmetical average roughness height (AARH) 配对法兰companion-flange螺栓圆bolt circle (B.C.)1.5 垫片Gasket (GSKT)垫片的型式type of gasket平垫片flat gasket环形平垫片flat ring gasket平金属垫片flat metal gasket夹棉织物的橡胶elastomer with cotton fabric insertion夹石棉织物的橡胶elastomer with asbestos fabric insertion夹石棉织物及金属丝加强的橡胶elastomer with asbestos fabricinsertion and with wire reinforcement无石墨压缩白石棉垫片non graphited compressed white asbestos gasket 天然白橡胶垫片natural white rubber gasket压缩石棉垫片compressed asbestos class gasket浸聚四氟乙烯的石棉垫片PTFE impregnated asbestos gasket夹石棉的缠绕金属垫片spiral-wound metal gasket with asbestos filler 内环inner ring外环,外定位环outer ring波纹金属垫片corrugated metal gasket波纹金属包嵌石棉垫片corrugated metal gasket with asbestos inserted双夹套波纹金属包石棉垫片corrugated metal double jacketed asbestos filled gasket 双夹套垫片double jacketed gasket金属包石棉平垫片flat metal jacketed asbestos filled gasket整体金属齿形垫片solid metal serrated gasket槽形金属垫片grooved metal gasket环形连接金属垫片ring joint metal gasket八角环形垫片octagonal ring gasket椭圆环形垫片oval ring gasket透镜式垫片lens gasket非金属垫片non-metallic gasket1.6 阀门Valve1.6.1 阀门结构、零件阀轭yoke外螺纹阀杆及阀轭outside screw and yoke (OS & Y) 阀杆stem内螺纹inside screw (IS)阀轭套yoke sleeve阀杆环stem ring阀座valve seat (body seat)阀座环、密封圈seat ring整体(阀)座integral seat堆焊(阀)座deposited seat阀芯(包括密封圈、杆等内件)trim阀盘disc阀盘密封圈disc seat阀体body阀盖bonnet阀盖衬套bonnet bush螺纹阀帽screw cap螺纹阀盖screw bonnet螺栓连接的阀盖bolted bonnet (BB) 活接阀盖(帽)union bonnet (cap)螺栓连接的阀帽bolted cap (BC)焊接阀盖welded bonnet (WB)本体阀杆密封body stem seal石棉安全密封asbestos emenen seal倒密封back seal压力密封的阀盖pressure-tight bonnet 动力操纵器powered operator电动操纵器electric motor operator 气动操纵器pneumatic operator液压操纵器hydraulic operator快速操纵器quick-acting operator滑动阀杆sliding stem正齿轮传动spur gear operated伞齿轮传动bevel gear operated扳手操作wrench operated链轮chain wheel手轮hand wheel手柄hand lever (handle)气缸(或液压缸)操纵的cylinder operated链条操纵的chain operated等径孔道full bore; full port异径孔道reducing bore, reduced port,venturi port 短型short pattern紧凑型(小型)compact type笼式环lantern ring压盖gland阀杆填料stem packing阀盖垫片bonnet gasket升杆式(明杆)rising stem (RS)非升杆式(暗杆)non-rising stem (NRS)指示器/限位器indicator/stopper注油器grease injector可更换的阀座环renewable seat ring1.6.2 常用阀(1)闸阀gate valve平行双闸板double disc parallel seat开口楔形闸板split wedge挠性整体楔形闸扳flexible solid wedge整体楔形闸板solid wedge塞型闸阀plug gate valve直通型闸阀through conduit gate valve(2) 截止阀globe valve球心型阀盘globe type disc塞型阀盘plug type disc可转动的阀盘swivel disc(3) 节流闪阀throttle valve针阀needle valve(4) 角阀angle valve(5) Y型阀(Y 型阀体截止阀)Y-valve (Y-body globe valve)(6) 球阀ball valve三通球阀3-way ball valve装有底轴的trunnion mounted耐火型fire safe type浮动球型floating ball type防脱出阀杆blowout proof stem(7) 蝶阀butterfly valve对夹式(薄片型)wafer type凸耳式lug type偏心阀板蝶阀offset disc burerfly valve; eccentric butterfly valve 斜阀盘蝶阀canted disc butterfly valve连杆式蝶阀link butterfly valve8) 柱塞阀piston type valve(9) 旋塞阀plug valve三通旋塞阀three-way plug valve四通旋塞阀four-way plug valve旋塞cock衬套旋塞sleeve cock(10) 隔膜阀diaphragm valve橡胶衬里隔膜阀rubber lined diaphragm valve直通式隔膜阀straight way diaphragm valve堰式隔膜阀weir diaphragm valve(11) 夹紧式胶管阀pinch valve(用于泥浆、粉尘等)(12) 止回阀check valve升降式止回阀lift check valve旋启式止回阀swing check valve, flap check valve 落球式止回阀ball check valve弹簧球式止回阀spring ball check valve双板对夹式止回阀dual plate wafer type check valve 无撞击声止回阀non-slam cheek valve底阀foot valve切断式止回阀stop check valve; non-return valve活塞式止回阀piston check valve斜翻盘止回阀tilting disc check valve蝶式止回阀butterfly check valve1.6.3 其它用途的阀安全泄气阀safety valve (SV)安全泄液阀relief valve (RV)安全泄压阀safety relief valve杠杆重锤式lever and weight type引导阀操纵的安全泄气阀pilot operated safety valve复式安全泄气阀twin type safety valve罐底排污阀flush-bottom tank valve电磁阀solenoid valve, solenoid operated valve电动阀electrically operated valve, electric-motor operated valve 气动阀pneumatic operated valve低温用阀cryogenic service valve蒸汽疏水阀steam trap机械式疏水阎mechanical trap浮桶式疏水阀open bucket trap, open top bucket trap浮球式疏水阀float trap倒吊桶式疏水阀inverted bucket trap自由浮球式疏水阀loose float trap恒温式疏水阀thermostatic trap金属膨胀式蒸汽疏水阀metal expansion steam trap液体膨胀式蒸汽疏水阀liquid expansion steam trap双金属膨胀式蒸汽疏水阀bimetallic expansion steam trap压力平衡式恒温疏水阀balanced pressure thermostatic trap热动力式疏水阀thermodynamic trap脉冲式蒸汽疏水阀impulse steam trap放气阀(自动放气阀)air vent valve (automatic air vent valve) (疏水阀用)平板式滑动闸阀slab type sliding gate valve盖阀flat valve换向阀diverting valve, reversing valve热膨胀阀thermo expansion valve自动关闭阀self-closing gate valve自动排液阀self-draining valve管道盲板阀line-blind valve挤压阀squeeze valve(用于泥浆及粉尘等)呼吸阀breather valve风门、挡板damper减压阀pressure reducing valve, reducing valve控制阀control valve膜式控制阀diaphragm operated control valve执行机构actuator背压调节阀back pressure regulating valve差压调节阀differential pressure regulating valve 压力比例调节阀pressure ratio regulating valve 1.6.4 未指明结构(或阀型)的阀切断阀block valve; shut-off valve; stop valve调节阀regulating valve快开阀quick opening valve快闭阀quick closing valve隔断阀isolating valve三通阀three way valve夹套阔jacketed valve非旋转式阀non-rotary valve排污阀blowdown valve集液排放阀drip valve排液阀drain valve放空阀vent valve卸载阀unloading valve排出阀discharge valve吸入阀suction valve多通路阀multiport valve取样阀sampling valve手动阀hand-operated valve; manually operated valve 锻造阀forged valve铸造阀cast valve(水)龙头bibb; bib; faucet抽出液阀(小阀)bleed valve旁路阀by-pass valve软管阀hose valve混合阀mixing valve破真空阀vacuum breaker冲洗阀flush valve第一道阀;根部阀primary valve根部阀root valve总管阀header valve事故切断阀emergency valve1.7 管道特殊件Piping Specialty1.7.1 管道特殊件(组件)粗滤器strainer过滤器filter临时粗滤器(锥型)temporary strainer (cone type) y 型粗滤器y-type strainerT型粗滤器T-type strainer永久过滤器permanent filter丝网粗滤器gauze strainer洗眼器及淋浴器eye washer and shower视镜sight glass阻火器flame arrester喷嘴;喷头spray nozzle取样冷却器sample cooler消声器silencer膨胀节expansion joint波纹膨胀节bellow expansion joint单波single bellow双波double bellow多波multiple bellow压力平衡式膨胀节pressure balanced expansion带铰链膨胀节hinged expansion joint轴向位移型膨胀节axial movement type expansion joint 自均衡膨胀节(外加强环)self-equalizing expansion joint 带接杆膨胀节tied expansion joint万向型膨胀节universal type expansion joint球形补偿器ball type expansion joint填函式补偿器slip type (packed type) expansion joint单向滑动填料函补偿器single actionpacked slip joint1.7.2 管道特殊元件Piping Special Element软管接头hose connection (HC)快速接头quick coupling金属软管metal hose橡胶管rubber hose挠性管flexible tube鞍形补强板reinforcing saddles补强板reinforcement pad特殊法兰special flange漏斗funnel排液环drip ring排液漏斗drain funnel插板blank垫环spacer8字盲板spectacle blind; figure 8 blind 限流孔板restriction orifice爆破片rupture disk法兰盖贴面protective disc费托立克接头victaulic coupling1.8 端部连接End Connection法兰端flanged end坡口端beveled end (BE)对焊端butt welded end平端plain end (PE)承插焊端socket welding end螺纹端threaded end (TE)承口bell end焊接端welding end法兰连接(接头)flanged joint对焊连接(接头)butt welded joint螺纹连接,管螺纹连接threaded joint, pipe threaded joint 锥管螺纹密封焊连接seal-welded taper pipe threaded joint 承插焊连接(接头)socket welded joint承插连接(接头)bell and spigot joint环垫接头ring joint (RJ)万向接头universal joint软钎焊连接(接头)soldered joint搭接接头,松套连接lapped joint外侧厚度切斜角bevel for outside thickncss内侧厚度切斜角bevel for inside thickness内外侧厚度切斜角bevel for combined thickness 法兰式的flanged (FLGD)对焊的butt welded (BW)螺纹的threaded (THD)承插焊的socket welded (SW)小端为平的small end plain (SEP)大端为平的large end plain (LEP)两端平both ends plain (BEP)小端带螺纹small end thread (SET)大端带螺纹large end thread (LET)两端带螺纹both end thread (BET)一端带螺纹one end thread (OET)支管连接branch connection焊接支管 branch pipe welded directly to the run pipe。
管道工程英文术语缩写
管道工程英文术语缩写标准化文件发布号：（9312-EUATWW-MWUB-WUNN-INNUL-DDQTY-KII管道工程英文术语缩写（中英对照）1.管子及管件P 管子 PipeEL 弯头ELL 长半径弯头ELS 短半径弯头MEL 斜接弯头（虾米腰弯头）REL 异径弯头T 三通 TeeLT 斜三通RT 异径三通R 异径管接头（大小头） ReducerCR 同心异径管接头（同心大小头） Concentric reducerER 偏心异径管接头（偏心大小头） Eccentric reducerCPL 管箍 CouplingFCPL 双头管箍 Full couplingHCPL 单头管箍 Half couplingRCPL 异径管箍 Reducing couplingBU 内外螺纹接头 BushingUN 活接头 UnionHC 软管接头 Hose couplerSE 翻边短节 Stub endNIP 短节 Pipe nipple or straight nippleSNIP 异径短节 Swaged nippleCP 管帽（封头） CapPL 管堵（丝堵） PlugBLK 盲板 BlankSB 8字盲板 Spectacle blind (blank)RP 补强板 Reinforcing pad2.法兰 FLG 法兰 FlangeWNF 对焊法兰 Welding neck flangeSOF 平焊法兰 Slip-on flangeSWF 承插焊法兰 Socket-welding flangeT 螺纹法兰 Threaded flangeLJ 松套法兰 Lapped joint flangeREDF 异径法兰 Reducing flangeBF 法兰盖（日法兰） Blind flangeFSF 法兰密封面 Flange scaling FF 全平面 Flat face RF 凸台面 Raised faceMFF 凹凸面 Male and female faceLF 凹面 Female faceLM 凸面 Male faceRJ 环连接面 Ring joint faceTG 榫槽面 Tongue and groove faceTF 榫面 Tongue faceGF 槽面 Groove face3.垫片 G 垫片 GasketNMG 非金属垫片 Non-metallic gasketAG 石棉垫片 Asbestos gasketRG 橡胶垫片 Rubber gasketTEG 聚四氟乙烯包复垫片 PTFE envelope gasket SMG 半金属垫片 Semimetallic gasketMJG 金属包垫片 Meta-jacket gasketSWG 缠绕式垫片 Spiral wound gasketMG 金属垫片 Metallic gasketFMG 金属平垫片 Flat metallic gasketSMSG 齿形金属垫片 Solid metal serrated gasket LER 透镜式金属环垫 Lens ring gasketOCR 八角形金属环垫 Octagonal ring gasketOVR 椭圆形金属环垫 Oval ring gaksetIR/OR 内外定位环 Inner ring and outer ringIR 内定位环 Inner ringOR 外定位环 Outer ring4.坚固件 B 螺栓 BoltSB 螺柱 Stud boltNU 螺母 NutTB 花蓝螺母 TurnbuckleWSR 垫圈 WasherSWSR 弹簧垫圈 Spring washer5.阀门 GV 闸阀 Gate valveGLV 截止阀 Globe valveCHV 止回阀 Check valveBUV 蝶阀 Butterfly valveBAV 球阀 Ball valvePV 旋塞阀 Plug valve (cock)CV 调节阀 Control valveSV 安全阀 Safety valveRV 减压阀 Pressure reducing valveST 蒸汽疏水阀 Steam trapPRV 泄压阀 Pressur relief valveBV 呼吸阀 Breather valveNV 针形阀 Needle valveAV 角阀DV 隔膜阀TWV 三通阀SGV 插板阀6.管道上用的小型设备 SPR 气液分离器 Separator FA 阻火器 Flame arresterSR 过滤器 StrainerSRY Y型过滤器 Y-type strainerSRT T型过滤器 T-type strainerSRB 桶式过滤器 Bucket type strainerTSR 临时过滤器 Temporary strainerSIL 消声器 SilencerSG 视镜 Slight glassSC 取样冷却器 Sample coolerDF 排液漏斗 Drain funnelLM 管道混合器 Line mixerRO 限流孔板 Restriction orificeMO 混合孔板 Mixing orificeRD 爆破片（爆破膜） Rupture diskEJ 补偿器 Expansion joint7.隔热、伴热 INS 隔热 Thermal insulationH 保温 Hot insulationC 保冷 Cold insulationP 防烫伤隔热 Personnel protection insulationT&I 伴热 Tracing and insulationT 管道伴热（冷） TracingEST 蒸汽外伴热 External steam tracingIST 蒸汽内伴热 Internal steam tracingSJT 蒸汽夹套伴热 Steam-jacket tracingET 电伴热 Electric tracing8.配管材料和等级 M 金属材料 Metallic material CS 碳钢 Carbon steelCAS 铸钢 Cast steelFS 锻钢 Forged steelAS 合金钢 Alloy steelSS 不锈钢 Stainless steelAUSTSS 奥氏体不锈钢 Austenitic stainless-steelCI 铸铁 Cast ironMI 可锻铸铁 Malleable ironDI 球墨铸铁 Ductile ironAL 铝 AluminumBRS 黄铜 BrassBRZ 青铜 BronzeCU 紫铜 CopperLAS 低合金钢 Low alloy steelFLAS 低合金锻钢 Forged low alloy steelCLAS 低合金铸钢 Cast low alloy steelTHK 壁厚 ThicknessSCH 表号 Schedule numberSTD 标准 StandardXS 加强 Extra strongXXS 特强 Double extra strong9.装置布置 CN 建北 Construction northE 东 EastW 西 WestS 南 SouthN 北 NorthH 水平 HorizontalV 竖直、铅直、直立 VerticalGRD 地坪 GroundUG 地下 UndergroundBL 装置边界线 Battery limit lineESEW 事故沐浴洗眼器 Emergency shower and eye washer HS 软管站 Hose stationML 接续分界线 Match linePS 管道支架（管架） Piping supportPR 管桥 Pipe rackSTRU 构架（构筑物） StructureBLDG 建筑物 BuildingPD 清扫设施 Purge devicePT 池 PitSHLT 棚 ShelterCOFF 围堰 CofferdamFL 楼板 FloorPF 平台 Plateform10.尺寸标注 EL 标高 Elevation BOP 管底 Bottom of pipeCOP 管中心Center of pipeTOP 管顶 Top of pipeFOB 底平 Flat on bottomFOT 顶平 Flat on topCL(屯) 中心线 Center lineTL 切线 Tangent lineSYM 对称的 SymmetricalBOS 支架底 Bottom of supportTOS 支架顶 Top of supportCL 净距（净空） ClearanceCTC 中心至中心 Center to centerCTF 中心至面 Center to faceCTE 中心至端部 Center to endETE 端到端 End to endFEF 法兰端面 Flange and faceFTF 面到面 Face to faceD 直径 DiameterDN 公称直径 Nominal diameterID 内径 Inside diameterOD 外径 Outside diameterDIM 尺寸 DimensionMAX 最大 MaximumMIN 最小 MinimumAVG 平均 AverageAPP 约、近似 Approximate点标高 Point elevation11.图表 PFD 工艺流程图 Process flow diagramPID 管道和仪表流程图 Piping & instrument diagramCOD 接续图 Continued on drawingDTL 详图 DatailSPDWG(ISODWG) 管段图 Spool drawing (each line isometric drawing) DWGNO 图号 Drawing numberDWGI 所在图号 Drawing identificationLOW 材料表 List of materialMTO 汇料 Material take-offAPPX 附录 AppendixJOB. No. 工号 Job NumberBEDD 基础工程设计数据 Basic engineering design dataDEDD 详细工程设计数据 Detail engineering design dataREV. No. 修改号 Recision numberREFDWG 参考图 Reference drawingSC 采样接口 Sample connection12.操作方式及工作参数 AUT 自动 Automatic ML 手动 Manual controlCHOP 链条操作 Chain operatedCSC 铅封关 Car seal closeCSO 铅封开 Car seal openLC 锁闭 Lock closedLO 锁开 Lock openNC 正常关 Normally closeNO 正常开 Normally openATM 大气压 AtmospherePN 公称压力 Nominal pressureA 绝压G 表压(T) 温度 Temperature(P) 压力 Pressure13.施工 W 焊接 WeldingAW 电弧焊 Arc weldingGSAW 气体保护电弧焊 Gas shielded-acr welding EFW 电熔焊 Elecric fusion weldingERW 电阻焊 Electric Resistance weldingGW 气焊 Gas weldingLW 搭接焊 Lap weldingBW 对焊 Butt weldingTW 定位焊 Tack weldingSW 承插焊 Socket weldingCW 连续焊 Continuous weldingSEW 密封焊 Seal weldingSFG 堆焊 SurfacingFW 现场焊接 Field weldingHT 热处理 Heat treatmentPH 预热 PreheatingSR 应力消除 Stress reliefPWHT 焊后热处理 Post weld heat treatmentEIT 检查、探伤和实验 Examination, inspection & testing VE 外观检查 Visual examinationUI (UT) 超声探伤 Ultrasonic inspection (test)RI (RT) 射线探伤 Radiographic inspection (test)MPI (MT) 磁粉探伤 Magnetic particle inspection (test) LPI (PT) 液体渗透检验 Liquid penterant inspection (test) HADT 硬度实验 Hardness testingHYDT 水压实验 Hydraulic testingPNET 气压实验 Pneumatic testingCE 焊条 Covered electrodeWW 焊丝 Welding wireASSY 装配、组合 AssemblyF 现场 FieldF/F 现场制造 Field faricatedSF 现场决定 Suit in fieldCSP 冷紧 Cold springBCT 螺栓冷紧 Bolt cold tighteningBHY 螺栓热紧 Bolt hot tighteningCO 清洗口 Clean outANNY 退火 AnnealedPE 平端面 Plain endBE 坡口端 Belelled endTHR 螺纹 ThreadHB 布氏硬度 Brinnel hardnessRC 洛氏硬度14.其他 FDN 基础 FoundationINF 信息（资料） InformationREF 参考 ReferenceREV 修改 RevisionSEQ 序号（顺序） SequenceW/E 设备带来 With equipmentW/I 仪表带来 With instrumentCM 色标 Colour markCA 腐蚀裕度 Corrosion allowanceUTL 公用系统 UtilityUC 公用工程接头 Utility connectionQTY 数量 QuantityWT 重量 WeightMHR 工时 Man hourBC 螺栓分布圆 Bolt circleHP 高点 High pointLP 低点Low pointSUC 吸入（口） SuctionDIS 排出（口） DischargeSO 蒸气吹扫（口） Steam outNPT 美国标准锥管螺纹 National standard taper pipe thread NPS 美国标准直管螺纹 National standard straight pipe thread DR 排液 DrainVT 放气 VentRTG （压力）等级 RatingCL 等级 ClassSMLS 无缝 Seamless螺旋缝。
化工管道工程使用技术词汇中英文对照
化工管道工程使用技术词汇中英文对照化工管道工程是指针对化工领域的管道系统设计、施工、维护、管理和安全监控等的技术应用。
在化工管道工程中，有着大量的技术术语需要使用，下面将为大家介绍一些常见的化工管道工程技术词汇的中英文对照。
1. 阀门valve/gate valve2. 泵pump3. 压力pressure4. 流量flow rate5. 温度temperature6. 热传导thermal conductivity7. 尺寸dimensions8. 焊接welding9. 管道材料pipe material10. 耐蚀性corrosion resistance11. 管道尺寸diameter12. 压力等级pressure rating13. 压力容器pressure vessel14. 管件fittings15. 泄压valve relief valve16. 自动控制automatic control17. 管路输送pipeline transportation18. 管线管道pipeline19. 管路变化pipeline change20. 隔膜式阀门diaphragm valve21. 球阀ball valve22. 聚乙烯管道PVC pipe23. 聚氯乙烯管道PE pipe24. 钢管道steel pipe25. 抗震性seismic resistance26. 减震降噪shock absorption and noise reduction27. 绝缘insulation28. 推力补偿器thrust compensator29. 弹性支座elastic support30. 固定支座fixed support31. 密封seal32. 活塞泵piston pump33. 电导率conductivity34. 温度控制temperature control35. 动态平衡dynamic balance36. 冷却器cooler37. 管线附属设备pipeline ancillary equipment38. 流量计flow meter39. 泄漏检测器leak detector40. 自动取样器automatic sampler以上就是一些常见的化工管道工程技术词汇的中英文对照。
管道工程英文术语缩写
管道工程英文术语缩写（中英对照）1.管子及管件1.1 P 管子 Pipe1.2 EL 弯头1.2.1 ELL 长半径弯头1.2.2 ELS 短半径弯头1.2.3 MEL 斜接弯头（虾米腰弯头）1.2.4 REL 异径弯头1.3 T 三通 Tee1.3.1 LT 斜三通1.3.2 RT 异径三通1.4 R 异径管接头（大小头） Reducer1.4.1 CR 同心异径管接头（同心大小头） Concentric reducer 1.4.2 ER 偏心异径管接头（偏心大小头） Eccentric reducer 1.5 CPL 管箍 Coupling1.5.1 FCPL 双头管箍 Full coupling1.5.2 HCPL 单头管箍 Half coupling1.5.3 RCPL 异径管箍 Reducing coupling1.6 BU 内外螺纹接头 Bushing1.7 UN 活接头 Union1.8 HC 软管接头 Hose coupler1.9 SE 翻边短节 Stub end1.10 NIP 短节 Pipe nipple or straight nipple1.10.1 SNIP 异径短节 Swaged nipple1.11 CP 管帽（封头） Cap1.12 PL 管堵（丝堵） Plug1.13 BLK 盲板 Blank1.13.1 SB 8字盲板 Spectacle blind (blank)1.14 RP 补强板 Reinforcing pad2.法兰2.1 FLG 法兰 Flange2.1.1 WNF 对焊法兰 Welding neck flange2.1.2 SOF 平焊法兰 Slip-on flange2.1.3 SWF 承插焊法兰 Socket-welding flange2.1.4 T 螺纹法兰 Threaded flange2.1.5 LJ 松套法兰 Lapped joint flange2.1.6 REDF 异径法兰 Reducing flange2.1.7 BF 法兰盖（日法兰） Blind flange2.2 FSF 法兰密封面 Flange scaling face2.2.1 FF 全平面 Flat face 2.2.2 RF 凸台面 Raised face2.2.3 MFF 凹凸面 Male and female face2.2.4 LF 凹面 Female face2.2.5 LM 凸面 Male face2.2.6 RJ 环连接面 Ring joint face2.2.7 TG 榫槽面 Tongue and groove face2.2.8 TF 榫面 Tongue face2.2.9 GF 槽面 Groove face3.垫片3.1 G 垫片 Gasket3.1.1 NMG 非金属垫片 Non-metallic gasket3.1.1.1 AG 石棉垫片 Asbestos gasket3.1.1.2 RG 橡胶垫片 Rubber gasket3.1.1.3 TEG 聚四氟乙烯包复垫片 PTFE envelope gasket3.1.2 SMG 半金属垫片 Semimetallic gasket3.1.2.1 MJG 金属包垫片 Meta-jacket gasket3.1.2.2 SWG 缠绕式垫片 Spiral wound gasket3.1.3 MG 金属垫片 Metallic gasket3.1.3.1 FMG 金属平垫片 Flat metallic gasket3.1.3.2 SMSG 齿形金属垫片 Solid metal serrated gasket3.1.3.3 LER 透镜式金属环垫 Lens ring gasket3.1.3.4 OCR 八角形金属环垫 Octagonal ring gasket3.1.3.5 OVR 椭圆形金属环垫 Oval ring gakset3.1.3.6 IR/OR 内外定位环 Inner ring and outer ring3.1.3.7 IR 内定位环 Inner ring3.1.3.8 OR 外定位环 Outer ring4.坚固件4.1 B 螺栓 Bolt4.1.1 SB 螺柱 Stud bolt4.2 NU 螺母 Nut4.3 TB 花蓝螺母 Turnbuckle4.4 WSR 垫圈 Washer4.4.1 SWSR 弹簧垫圈 Spring washer5.阀门5.1 GV 闸阀 Gate valve5.2 GLV 截止阀 Globe valve5.3 CHV 止回阀 Check valve5.4 BUV 蝶阀 Butterfly valve5.5 BAV 球阀 Ball valve5.6 PV 旋塞阀 Plug valve (cock)5.7 CV 调节阀 Control valve5.8 SV 安全阀 Safety valve5.9 RV 减压阀 Pressure reducing valve5.10 ST 蒸汽疏水阀 Steam trap5.11 PRV 泄压阀 Pressur relief valve5.12 BV 呼吸阀 Breather valve5.13 NV 针形阀 Needle valve5.14 AV 角阀5.15 DV 隔膜阀5.16 TWV 三通阀5.17 SGV 插板阀6.管道上用的小型设备6.1 SPR 气液分离器 Separator 6.2 FA 阻火器 Flame arrester6.3 SR 过滤器 Strainer6.3.1 SRY Y型过滤器 Y-type strainer6.3.2 SRT T型过滤器 T-type strainer6.3.3 SRB 桶式过滤器 Bucket type strainer6.3.4 TSR 临时过滤器 Temporary strainer6.4 SIL 消声器 Silencer6.5 SG 视镜 Slight glass6.6 SC 取样冷却器 Sample cooler6.7 DF 排液漏斗 Drain funnel6.8 LM 管道混合器 Line mixer6.9 RO 限流孔板 Restriction orifice6.9.1 MO 混合孔板 Mixing orifice6.1 RD 爆破片（爆破膜） Rupture disk6.11 EJ 补偿器 Expansion joint7.隔热、伴热7.1 INS 隔热 Thermal insulation7.1.1 H 保温 Hot insulation7.1.2 C 保冷 Cold insulation7.1.3 P 防烫伤隔热 Personnel protection insulation7.2 T&I 伴热 Tracing and insulation7.3 T 管道伴热（冷） Tracing7.3.1 EST 蒸汽外伴热 External steam tracing7.3.2 IST 蒸汽内伴热 Internal steam tracing7.3.3 SJT 蒸汽夹套伴热 Steam-jacket tracing7.3.4 ET 电伴热 Electric tracing8.配管材料和等级8.1 M 金属材料 Metallic material 8.1.1 CS 碳钢 Carbon steel8.1.2 CAS 铸钢 Cast steel8.1.3 FS 锻钢 Forged steel8.1.4 AS 合金钢 Alloy steel8.1.5 SS 不锈钢 Stainless steel8.1.6 AUSTSS 奥氏体不锈钢 Austenitic stainless-steel8.1.7 CI 铸铁 Cast iron8.1.8 MI 可锻铸铁 Malleable iron8.1.9 DI 球墨铸铁 Ductile iron8.1.10 AL 铝 Aluminum8.1.11 BRS 黄铜 Brass8.1.12 BRZ 青铜 Bronze8.1.13 CU 紫铜 Copper8.1.14 LAS 低合金钢 Low alloy steel8.1.15 FLAS 低合金锻钢 Forged low alloy steel8.1.16 CLAS 低合金铸钢 Cast low alloy steel8.2 THK 壁厚 Thickness8.2.1 SCH 表号 Schedule number8.2.2 STD 标准 Standard8.2.3 XS 加强 Extra strong8.2.4 XXS 特强 Double extra strong9.装置布置9.1 CN 建北 Construction north9.2 E 东 East9.3 W 西 West9.4 S 南 South9.5 N 北 North9.6 H 水平 Horizontal9.7 V 竖直、铅直、直立 Vertical9.8 GRD 地坪 Ground9.9 UG 地下 Underground9.10 BL 装置边界线 Battery limit line9.11 ESEW 事故沐浴洗眼器 Emergency shower and eye washer 9.12 HS 软管站 Hose station9.13 ML 接续分界线 Match line9.14 PS 管道支架（管架） Piping support9.15 PR 管桥 Pipe rack9.16 STRU 构架（构筑物） Structure9.17 BLDG 建筑物 Building9.18 PD 清扫设施 Purge device9.19 PT 池 Pit9.20 SHLT 棚 Shelter9.21 COFF 围堰 Cofferdam9.22 FL 楼板 Floor9.23 PF 平台 Plateform10.尺寸标注10.1 EL 标高 Elevation 10.2 BOP 管底 Bottom of pipe10.3 COP 管中心Center of pipe10.4 TOP 管顶 Top of pipe10.5 FOB 底平 Flat on bottom10.6 FOT 顶平 Flat on top10.7 CL(屯) 中心线 Center line10.8 TL 切线 Tangent line10.9 SYM 对称的 Symmetrical10.10 BOS 支架底 Bottom of support10.11 TOS 支架顶 Top of support10.12 CL 净距（净空） Clearance10.13 CTC 中心至中心 Center to center 10.14 CTF 中心至面 Center to face10.15 CTE 中心至端部 Center to end10.16 ETE 端到端 End to end10.17 FEF 法兰端面 Flange and face10.18 FTF 面到面 Face to face10.19 D 直径 Diameter10.20 DN 公称直径 Nominal diameter10.21 ID 内径 Inside diameter10.22 OD 外径 Outside diameter10.23 DIM 尺寸 Dimension10.24 MAX 最大 Maximum10.25 MIN 最小 Minimum10.26 AVG 平均 Average10.27 APP 约、近似 Approximate10.28 PT.EL 点标高 Point elevation11.图表11.1 PFD 工艺流程图 Process flow diagram11.2 PID 管道和仪表流程图 Piping & instrument diagram11.3 COD 接续图 Continued on drawing11.4 DTL 详图 Datail11.5 SPDWG(ISODWG) 管段图 Spool drawing (each line isometric drawing) 11.6 DWGNO 图号 Drawing number11.7 DWGI 所在图号 Drawing identification11.8 LOW 材料表 List of material11.9 MTO 汇料 Material take-off11.10 APPX 附录 Appendix11.11 JOB. No. 工号 Job Number11.12 BEDD 基础工程设计数据 Basic engineering design data 11.13 DEDD 详细工程设计数据 Detail engineering design data 11.14 REV. No. 修改号 Recision number11.15 REFDWG 参考图 Reference drawing11.16 SC 采样接口 Sample connection12.操作方式及工作参数12.1 AUT 自动 Automatic 12.2 ML 手动 Manual control12.3 CHOP 链条操作 Chain operated12.4 CSC 铅封关 Car seal close12.5 CSO 铅封开 Car seal open12.6 LC 锁闭 Lock closed12.7 LO 锁开 Lock open12.8 NC 正常关 Normally close12.9 NO 正常开 Normally open12.10 ATM 大气压 Atmosphere12.11 PN 公称压力 Nominal pressure12.12 A 绝压12.13 G 表压12.14 (T) 温度 Temperature12.15 (P) 压力 Pressure13.施工13.1 W 焊接 Welding13.1.1 AW 电弧焊 Arc welding13.1.2 GSAW 气体保护电弧焊 Gas shielded-acr welding 13.1.3 EFW 电熔焊 Elecric fusion welding13.1.4 ERW 电阻焊 Electric Resistance welding13.1.5 GW 气焊 Gas welding13.1.6 LW 搭接焊 Lap welding13.1.7 BW 对焊 Butt welding13.4.8 TW 定位焊 Tack welding13.1.9 SW 承插焊 Socket welding13.1.10 CW 连续焊 Continuous welding13.1.11 SEW 密封焊 Seal welding13.1.12 SFG 堆焊 Surfacing13.1.13 FW 现场焊接 Field welding13.2 HT 热处理 Heat treatment13.2.1 PH 预热 Preheating13.2.2 SR 应力消除 Stress relief13.2.3 PWHT 焊后热处理 Post weld heat treatment13.3 EIT 检查、探伤和实验 Examination, inspection & testing 13.3.1 VE 外观检查 Visual examination13.3.2 UI (UT) 超声探伤 Ultrasonic inspection (test)13.3.3 RI (RT) 射线探伤 Radiographic inspection (test)13.3.4 MPI (MT) 磁粉探伤 Magnetic particle inspection (test) 13.3.5 LPI (PT) 液体渗透检验 Liquid penterant inspection (test) 13.3.6 HADT 硬度实验 Hardness testing13.3.7 HYDT 水压实验 Hydraulic testing13.3.8 PNET 气压实验 Pneumatic testing13.3.9 CE 焊条 Covered electrode13.3.10 WW 焊丝 Welding wire13.3.11 ASSY 装配、组合 Assembly13.3.12 F 现场 Field13.3.13 F/F 现场制造 Field faricated13.3.14 SF 现场决定 Suit in field13.3.15 CSP 冷紧 Cold spring13.3.16 BCT 螺栓冷紧 Bolt cold tightening13.3.17 BHY 螺栓热紧 Bolt hot tightening13.3.18 CO 清洗口 Clean out13.3.19 ANNY 退火 Annealed13.4 PE 平端面 Plain end13.5 BE 坡口端 Belelled end13.6 THR 螺纹 Thread13.7 HB 布氏硬度 Brinnel hardness13.8 RC 洛氏硬度14.其他14.1 FDN 基础 Foundation14.2 INF 信息（资料） Information14.3 REF 参考 Reference14.4 REV 修改 Revision14.5 SEQ 序号（顺序） Sequence14.6 W/E 设备带来 With equipment14.7 W/I 仪表带来 With instrument14.8 CM 色标 Colour mark14.9 CA 腐蚀裕度 Corrosion allowance14.10 UTL 公用系统 Utility14.11 UC 公用工程接头 Utility connection14.12 QTY 数量 Quantity14.13 WT 重量 Weight14.14 MHR 工时 Man hour14.15 BC 螺栓分布圆 Bolt circle14.16 HP 高点 High point14.17 LP 低点Low point14.18 SUC 吸入（口） Suction14.19 DIS 排出（口） Discharge14.20 SO 蒸气吹扫（口） Steam out14.21 NPT 美国标准锥管螺纹 National standard taper pipe thread 14.22 NPS 美国标准直管螺纹 National standard straight pipe thread 14.23 DR 排液 Drain14.24 VT 放气 Vent14.25 RTG （压力）等级 Rating14.26 CL 等级 Class14.27 SMLS 无缝 Seamless14.28 螺旋缝。
供热、供燃气、 通风及空调工程 英语
供热、供燃气、通风及空调工程英语英语1. 供热工程英语词汇1.1 Central heating system 中央供暖系统1.2 Radiator 散热器1.3 Boiler 锅炉1.4 Heat exchanger 热交换器1.5 Thermostat 温控器1.6 Heat pump 热泵1.7 Underfloor heating 地暖1.8 District heating 集中供热1.9 Heat transfer 传热1.10 Insulation isolation 绝缘隔离2. 供燃气工程英语词汇2.1 Gas pipeline 天然气管道2.2 Gas meter 燃气表2.3 Gas leak detector 燃气泄漏探测器2.4 Gas appliances 燃气器具2.5 Gas regulator 燃气调压器2.6 Gas valve 燃气阀门2.7 Liquefied petroleum gas (LPG) 液化石油气2.8 Natural gas 天然气2.9 Gas cooktop 燃气灶台2.10 Gas safety 燃气安全3. 通风工程英语词汇3.1 Ventilation 通风3.2 Air duct 风管3.3 Air purifier 空气净化器3.4 Exhaust fan 排气扇3.5 HVAC system 暖通空调系统3.6 Fresh air 新风3.7 Air circulation 空气循环3.8 Ventilation rate 通风率3.9 Indoor air quality 室内空气质量3.10 Ventilation design 通风设计4. 空调工程英语词汇4.1 Air conditioning 空调4.2 Split system 空调分体机4.3 Ductless air conditioner 无风管空调4.4 Chiller 冷水机组4.5 Air handler 空气处理器4.6 Cooling tower 冷却塔4.7 Thermostat 温控器4.8 Refrigerant 制冷剂4.9 HVAC technician 暖通空调技师4.10 Air conditioning maintenance 空调维护保养5. 结语以上就是部分供热、供燃气、通风及空调工程的英语词汇，这些词汇在工程施工、维护以及交流中都起到了非常重要的作用。
给排水专业英语词汇(上)
Trench n.沟，渠Cistern n.蓄水池，储水器Drainage n.排水，排水设备，排水的水Foul n.污浊的Siphon n.虹吸（管）；用虹吸管输送Settle n.澄清，（使）沉淀Hydraulic a.水力学的Distillation n.蒸馏（法）Still n.蒸馏器Filtration n.过滤Clarification n.澄清，净化Coagulation n.絮凝，混凝Sanitation n.（环境）卫生Sedimentation n.沉淀，沉积Grate v.装格栅于Basin n.水池，水槽Catch basin 集水池，沉水池Lagoon n.污水池Patent vt，n.为……取得专利，专利，专利品Anticipate vt.促进Turbidity n.浑浊性，浑浊度Coagulant n.混凝剂，凝结剂Modification n.改变，改进，改良Toxic a.有毒的，中毒的Pathogenic a.致病的，病原的Microorganism n.微生物Congregate v.聚集Contaminate v.污染，弄脏Precipitate v.降水，沉降Precipitation n.沉降物（如雨，雪等）Contaminant n.污染物质Hydrological a.水文学的Nutrient n.养分，养料Medium n.介质，培养基Microbial a.微生物的，细菌的Algae n.藻类，海藻Protozoa n.原生动物Inorganics n.无机物Seep vi.渗入Effluent n.污水，废水Epidemic n.流行病，时疫Trace n.痕量，微量，微量金属Monitor v.检验（放射性污染物）Bacteriology n.细菌学Discharge n.排泄（水汽），排泄物Annual a.一年一度的，每年的Typhoid n.伤寒Cholera n.霍乱Round n.循环，周期Eradicate vt.根除，杜绝Lay down 制定，提出Superimpose vt.添加，附加Distil v.蒸馏Distillation n.蒸馏法Electrodialysis n.电渗析Brackish a.稍咸的Estuary n.河口，海湾Osmosis n.渗透性Estuarine a,河口的，港湾的Barrage n.拦河坝Sterilize vt.消毒，杀菌Wholesome a.卫生的，有益于健康的Injurious a.有害的Conductive a.有助于……的，促进的Be conductive to 对……有益的Constituent n.组成物，构成物Turbid a.浑浊的，混乱的Pathogen n.病原体，病菌Sedimentation n.沉积法，沉积作用Flocculate v.絮凝，绒聚Flocculating agent 絮凝剂Settlting n.沉淀Settling out 沉淀出来Coarse a.粗粒的，大的Floc n.絮体，絮凝物体Filtration n.过滤，澄清Chlorinate vt.用氯消毒Sanitary properties 卫生系数（性能，特点等）Colloidal a.胶体（状，质）的Suspension n.悬浮（液），悬浮（体）Portability a.可饮用Detract v.降低，减损Rayon n.人造丝Cellulose n.纤维素Starch n.淀粉Odour n.气味，臭气Secretion n.分泌液Fungi n.真菌Phenol n.（苯）酚Chlorine n.氯气Malodorous a.恶臭的Chlorophenols n.氯酚Break-point chlorination 折点加氯Activated carbon 活性炭Chlorine dioxide 二氧化氯Ozone n.臭氧Silica n.二氧化硅Transparency n.透明（性，度）Mastic n.胶粘剂p.p.m=parts per million 百万分之（几）Coalesce vi.凝聚Decolorize vt.漂白Conductivity n.传导性Resistivity n.电阻性Bacteriological a.细菌学的Alkaline n./a.碱性，碱性的Acidity n.酸性（度）Alkalinity n.酸性（度）Alkalinity n.（强）碱性Corrosive a.腐蚀的Water-supply 给水的Storage reservoir 蓄水库（池）Pipeline n.管道（线）Distribution reservoir 配水库（池）Distribution pipe 配水管网High demands 高峰用水量Supply source 水源Air conditioning equipment 空调设备Water （supply）engineer 给水工程师The fire department 消防部门Catchment n.集水（量），汇水Catchment area 集水区Rainfall n.降雨量Refill v.再装满Runoff n.径流（量）Infiltration n.渗透（入）Infiltration water 渗透水Evaporation n.蒸发Evaporation water 蒸发水Impounding v.贮（水）备灌溉用Impounding reservoir 蓄水池Recharge v.再装，再补充Purify v.使纯净，使洁净Compressor n.压缩机Limestone n.石灰石Porous a.多孔的Formation n.地（岩）层Limestone formation 石灰岩层Porous formation 多空岩层Plumbing n.（自来水，卫生）管道（装置）室内给排水系统（管道，工程）System of plumbing 卫生工程系统（体系）Circulatory a.循环的，流通的Outbreak n.爆发，破裂Epidemic n.流行病，时疫Cross-connection 交叉传染Submerged a.水面下的Inlet n.进（气，水）口Submerged inlet 淹没式入口，进水口淹没Vent n.通风（排气）管（口）；排除，放气Deteriorate v.变质，损坏Appurtenance n.附属物，设备，附件，附属建筑（装置）Sanitary or storm drainage 生活用水或雨水的排放Distribution n.分布，配给Multitude n.许多，大批（量）A multitude of 许多的，众多的Uphill n.a.ad. 上坡，向上Valve n.阀门，开关Microbe n.微生物Lactic a.乳的Lactic acid 乳酸Breakdown n.分解，离解Fermentation n.发酵Equation n.反应式，公式Oxidize v.使氧化Acetic a.醋酸的，醋酸Oxidation n.氧化作用Atmospheric a.大气中的，空气的Butyric a.丁酸的，奶油的，丁酸Bacteria n.细菌Proliferate v.繁殖，繁衍Anaerobic a.厌氧的，厌气的Derivative a.转生的，派生的，衍生物Specialize v.使专门化，特殊化Attack vt.（化学）腐蚀，锈蚀Nutrition n.营养（学）Culture n.培养，养殖Media n.培养基Synthesize v.（人工）合成Preform vt.预先形成Biochemical a.生物化学的Municipal a.城市的Unsaturated a.未饱和的Suspended water 悬着水Intermolecular a.分子间的Aeration n.曝气，通气The zone of aeration 通气层Remainder n.剩余物Capillary a.n.毛细管的Fringe n.边缘，端Transpire v.蒸发，气化Compaction n.压实，压缩Pore n.小孔Intergranular a.颗粒间的Permeability n.渗透性，透气性Recharge well 回灌井Hydraulic a.水力学的Coefficient n.系数Substrate n.基质，底质Sediment n.沉积物Adjacent a.邻近的，相邻的Sodium n.钠Sodium chloride 氯化钠Ion n.离子Conduit n.导管，水管Sewerage n.下水道，污水（排水）工程（系统）Elevation n.高度，海拔Confines n.界限，范围，边界Rectangular a.矩（长方）形的Laminar a.层（式、状、流）的Turbulent a.湍流的Irrigation n.灌溉Nonuniform a.不均匀的，变化的Retard vt.延迟，减速流Retarded flow 滞流，减速流Component n.分（力，量，支）The component of the gravity 重力的分量Shear n.剪（切，力）切（变，力）Shear force 切力，剪力Spillway n.溢洪道Profile n.轮廓，断面（图）Resulting a.所引起（产生）的Resulting profile 所形成的剖面图Sanitary a.关于环境卫生的，卫生的Hydraulic a.水力的，水力学的，水压的Aqueduct n.沟渠，导水管，高架渠Reveal v.泄露，显示Archeological a.考古学的Pipeline n.管道线，输送管Cloaca n.暗渠，下水道，厕所Sewer n.污水池Cesspool n.阴沟，污水管，排水管，下水道Metropolis 首都，大城市，文化商业中心Tributary a.附属的，支流的Lawsuit n.诉讼Downstream a.ad.顺流的，在下游的Sewage n.污水，污物Range v.延伸，探寻，涉及Watershed n.流域，集水区Bedrock n.基岩Rainfall n.降雨，降水，降雨量Divert vt.转移，使转向Ecosystem n.生态系统Biosphere n.生物圈Biotope n.群落生境Inanimate a.非动物的Spatial a.空间的Biocoenosis n.生物群落Moor n.荒野，沼Savannah n.热带大草原Deciduous a.（在成熟期或一定季节）脱落的Flora n.植物群Fauna n.动物群Habitat n.栖息地Climatic a.气候的Terrestrial a.陆地的Aquatic a.水生的Abiotic a.非生物的Ecological a.生态的Autotrophic a.自养的Chloroplast a.叶绿体Herbaceous a.草本的Carbohydrate n.碳水化合物Assimilation n.吸收Heterotrophic a.异养的Herbivore a.食草的Decompose vt.分解Detritus n.腐质Invertebrate a.无脊椎的Carnivore n.食肉动物Arable a.适于耕作的Fluctuate v.波动，涨落Quantitative a.定量的Amplitude n.广大，充足Genetic a.遗传的Botanic a.植物的Compensate vt.补偿Integrated plant protection 综合植物保护Terminal community 最终群落Burgeon vt.发展，展开Deterioration n.恶化，变质Airborne a.空中的Adverse effect 反作用，不利影响Manifest a.明显的vt.表明，证明Catalytic a.催化的Copolymer n.共聚物Toxicity n.毒性，毒力Abatement n.减少，除去Emission n.散发，发射（物）Unrelenting a.不退让的，不松懈的Fusion n.合并，联合Megalopolis n.大城市（由几个城市及郊区连成者）Sparsely ad.稀疏地，稀少地Pollutant n.污染物Reside v.住（留），属于，与……靠得很近Juxtaposition n.并列，并置Severity n.严重性Intensification n.加强，强化Segment n.部分，分布Contaminant n.污染物质，杂质Internal combustion engine 内燃机Per capita 每人口Solid refuse 固体废物，固体垃圾Incinerator n.焚化炉，化灰炉Degradation n.退化，降低Originate vi.发起，发生Affluent a.富足的，丰富Dilution n.冲淡，稀释Dispersion n.分散（作用）弥散Irritation n.刺激，兴奋Hazardous a.有害的Handling characteristics 处理特性Garbage n.垃圾，废料Serve to 用于……Inoffensive a.无害的Inherent a.固有的，内在的Compost vt.把……做成堆肥Raw material 原材料Incineration n.焚化Supervision n.监督，管理Overweight vt.在重量上超过Densely ad.密集地，稠密地Landfill vi.土地掩埋Haul vt.用力拖（或拉）Option n.选择，选择权Municipal solid waste(MSW) 城市固体废物Ecological perspective 生态学观点Recoverable a.可重获的，可找到的Burial n.埋葬Pyrolysis n.热解作用Pyrolysis furnace 干馏炉，热解炉Destructive a.破坏性的Endothermic a.吸热的Exothermic a.放热的Oxygen-free environment 无氧环境Self-sustaining a.自给的Methane n.甲烷Methanol n.甲醇Tar n.焦油Combustible a.可燃的，易燃的Pose vt.造成，形成Aesthetic a.美学的Restrain…from(doing) 制止……（干）……Waste disposal 废物处理Feasibility n.可行性Enactment n.颁布Enforcement n.实施Combined sewer （system）合流制下水管（系统）Separated sewer (system) 分流制下水管（系统）Drain off 把……排除Bypass vt.越过，绕……走Minimize vt.使减少到最少Dilute vt.冲淡Settle out 沉淀出来Municipality n.市，市政府Undesirable a.讨厌的，令人不快的Inadequate a.不足的，不适当的Be acted on 受……作用Notably ad.显著地，著名地Tertiary a.第三极的Leach vt.滤去（物质）Leaching field 滤液场Septic a.引起腐烂的Septic tank 化粪池Detention n.滞留Interact vi.互相作用，互相影响Quest vi.追求，探索Biophysical a.生物物理学的Arithmetical a.算术的Coverage n.覆盖率Priority n.重点，优先Quantitative a.数量的，定量的Hygienic a.卫生的，卫生学的Indisputable a.无可争辩的，无可置疑的Programmer n.规划，订计划者Nationwide a.全国性的Criterion n.（批评，判断的）标准，准则Continuity n.连续性，持续性Forthcoming a.即将到来的，即将出现的Coherent a.一致的，粘附的Sustainable a.持续的，能忍受的Initiative n.倡议，首创精神Legislation n.立法，法规Implementation n.履行，实施Assessment n.评估，估价Underlying a.根本的，基础的Institutional a.制度上的，惯例的Undertaker n.承担者，承办人Water undertaker 自来水厂Privatization n.私有化Inspection n.检查，视察Entity n.实体，统一体。
工业管道设计技术词汇(汉英)
Ⅰ. 按汉语分类编排1. 管道组成件piping component1.1 管子管子（按照配管标准规格制造的）pipe管子（不安配管标准规格制造的其他用管）Tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢管stainless steel pipe奥氏体不锈钢管Austenitic stainless steel pipe铁合金钢管Ferritic alloy steel pipe轧制钢管Wrought-steel pipe锻铁管Wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管Electric-resistance welded steel pipe电熔（弧）焊钢板卷管Electric-fusion (arc)-welded steel-plate pipe螺旋焊接钢管Spiral welded steel pipe镀锌钢管Galvanized steel pipe热轧无缝钢管Hot-rolling seamless pipe冷拔无缝钢管Cold-drawing seamless pipe水煤气钢管Water-gas steel pipe塑料管Plastic pipe玻璃管Glass tube橡胶管Rubber tube直管Run pipe; straight pipe1.2 管件Fitting弯头Elbow异径弯头Reducing elbow带支座弯头base elbow长半径弯头Long radius elbow短半径弯头short radius elbow长半径180℃弯头long radius return短半径180℃弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand)双支管弯头double branch elbow三通Tee异径三通Reducing tee等径三通straight tee带侧向口的三通（右向或左向）Side outlet tee (right hand or left hand)异径三通（分支口为异径）Reducing tee (reducing on outlet)异径三通（一个直通口为异径）Reducing tee (reducing on one run)带支座三通Base tee异径三通（一个直通口及分支口为异径）Reducing tee (reducing on one runand outlet异径三通（两个直通口为异径）（双头式）reducing tee (reducing on both runs)(bull head)45℃斜三通45℃lateral45℃斜三通（支管为异径）45℃lateral (reducing on branch)45℃斜三通（一个直通口为异径）45℃lateral (reducing on one run)45℃斜三通（一个直通口及支管为异径）45℃lateral (reducing on one run andbranch)Y型三通（裤衩）Tube Y四通Cross等径四通Straight cross异径四通Reducing cross异径四通(一个分支口为异径) Reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）Reducing cross (reducing on one runand one outlet)异径四通（两个分支口为异径）Reducing cross (reducing on both outlets)异径四通（一个直通口及两个分支口为异径）Reducing cross (reducing on onerun and both outlets)异径管Reducer同心异径管Concentric reducer偏心异径管Eccentric reducer锻制异径管Reducing swage螺纹支管台Threadolet焊接支管台Weldolet承插支管台Sockolet弯头支管台Elbolet斜接支管台Latrolet镶入式支管嘴Sweepolet短管支管台Nipolet支管台，插入式支管台Boss管接头Coupling; full coupling半管接头Half coupling异径管接头Reducing coupling活接头Union内外螺纹缩接（俗称补芯）Bushing管帽Cap [C]堵头Plug短节Nipple异径短节Reducing nipple; swage nipple1.3 弯管预制弯管Fabricated pipe bend跨越弯管Cross-over bend偏置弯管Offset bend90℃弯管Quarter bend环形弯管Circle bend单侧偏置90℃弯管Single offset quarter bendS型弯管S bend单侧偏置U形膨胀弯管single offset U bendU形弯管U bend双偏置U膨胀弯管Double offset expansion U bend斜接弯管Mitre bend三节斜接弯管3-piece mitre bend折皱弯管Corrugated bend圆度Roundness1.4 法兰Flange [FLG]整体管法兰Integral pipe flange钢管法兰Steel pipe flange螺纹法兰Threaded flange滑套法兰（包括平焊法兰）Slip-on flange [SO]; Slip-on welding flange承插焊法兰Socket welding flange松套法兰Lap joint flange [LJF]对焊法兰Weld neck flange [WNF]法兰盖Blind flange; Blind孔板法兰Orifice flange异径法兰Reducing flange盘座式法兰Pad type flange松套带颈法兰Loose hubbed flange焊接板式法兰Welding plate flange对焊环Welding neck collar (similar to stub end)平焊环Welding-on collar突缘短节Stub end; Lap翻边端Lapped pipe end松套板式法兰Loose plate flange压力级Pressure rating; Pressure rating class压力-温度等级Pressure-temperature rating法兰密封面：法兰面Flange facing突面Raised face [RF]凸面Male face [MF]凹面Female face [FMF]榫面Tongue face槽面Groove face环连接面Ring joint face全平面；满平面Flat face; Full face光滑突面Smooth raised face [SRF]法兰面加工Facing finish粗糙度Roughness光滑的Smooth齿形有Serrated均方根Root mean square [RMS]算术平均粗糙高度Arithmetical average roughness height [AARH]配对法兰Companion flange螺栓圆Bolt circle1.5 垫片Gasket [GSKT]垫片的型式type of gasket平垫片Flat gasket环形平垫片Flat ring gasket平金属垫片Flat metal gasket夹棉织物的橡胶Elastomer with cotton fabric insertion夹石棉织物的橡胶Elastomer with asbestos fabric insertion夹石棉织物及金属丝加强的橡胶Elastomer with asbestos fabric insertion andwith wire reinforcement无石墨压缩白石棉垫片Non-graphited compressed white asbestos gasket天然白橡胶垫片natural white rubber gasket压缩石棉垫片Compressed asbestos gasket浸聚四氟乙烯的石棉垫片PTFE impregnated asbestos gasket夹石棉的缠绕金属垫片spiral-wound metal gasket with asbestos filler内环Inner ring外环；外定位环Outer ring波纹金属垫片Corrugated metal gasket波纹金属包嵌石棉垫片Corrugated metal gasket with asbestos inserted双夹套波纹金属包石棉垫片Corrugated metal double jacketed asbestos filledgasket双夹套垫片Double jacketed gasket金属包石棉平垫片Flat metal jacketed asbestos filled gasket整体金属齿形垫片Solid metal serrated gasket槽形金属垫片Grooved metal gasket环形连接金属垫片Ring joint metal gasket八角环形垫片Octagonal ring gasket椭圆环形垫片Oval ring gasket透镜式垫片Lens gasket非金属垫片Non-metallic gasket1.6 阀门1.6.1 阀门结构，零件阀轭Yoke外螺纹阀杆及阀轭outside screw & yoke [OS&Y]阀杆Stem内螺纹Inside screw [IS]阀轭套Yoke sleeve阀杆环Stem ring阀座Valve seat (body seat)阀座环，密封圈Seat ring整体（阀）座Integral seat堆焊（阀）座Deposited seat阀芯（包括密封圈，杆等内件）Trim阀盘Disc阀盘密封圈Disc seat阀体Body阀盖Bonnet阀盖衬套Bonnet bush螺纹阀帽Screw cap螺纹阀盖Screw bonnet螺栓连接的阀盖Bolted bonnet [BB]活接阀盖（帽）Union bonnet [cap]螺栓连接的阀帽bolted cap [BC]焊接阀盖Welded bonnet [WB]本体阀杆密封Body stem seal石棉安全密封asbestos emergency seal倒密封Back seal压力密封的阀盖pressure seal bonnet动力操纵器Powered operator电动操纵器Electric motor operator气动操纵器pneumatic operator液压操纵器Hydraulic operator快速操纵器Quick-acting operator滑动阀杆Sliding stem正齿轮传动Spur gear operated伞齿轮传动Bevel gear operated扳手操作Wrench operated链轮Chain wheel手轮Hand wheel手柄Hand lever (handle)气缸（或液压缸）操纵的Cylinder operated链条操纵的Chain operated等径孔道Full bore; full port异径孔道Reducing bore; reduced port; Venturi port 短型short pattern紧凑型（小型）compact type笼式环(套环) lantern ring压盖Gland阀杆填料Stem packing阀盖垫片Bonnet gasket升杆式（明杆）Rising stem [RS]非升杆式（暗杆）Non-rising stem [NRS]指示器/限位器Indicator/stopper注油器Grease injector可更换的阀座环Renewable seat ring1.6.2 常用阀（1）闸阀Gate valve平行双闸板double disc parallel seat开口楔形闸板split wedge挠性整体楔形闸板Flexible solid wedge整体楔形闸板solid wedge塞型闸阀plug gate valve直通型闸阀Through conduit gate valve（2）截止阀Globe valve球心型阀盘Globe type disc塞型阀盘Plug type disc可转动的阀盘Swivel disc（3）节流闪阀Throttle valve针阀needle valve（4）角阀Angle valve（5）Y型阀（Y型阀体截止阀）Y-valve (Y-body globe valve)（6）球阀ball valve三通球阀3-way ball valve装有地轴的Trunnion mounted耐火型Fire safe type浮动球阀Floating ball type防脱出阀杆blowout proof stem（7）蝶阀butterfly valve对夹式（薄片型）Wafer type凸耳式Lug type偏心阀板蝶阀Offset disc butterfly valve; Eccentric butterfly valve斜阀盘蝶阀Canted disc butterfly valve连杆式蝶阀Link butterfly valve（8）柱塞阀Piston type valve（9）旋塞阀Plug valve三通旋塞阀3-way plug valve四通旋塞阀Four-way plug valve旋塞Cock衬套旋塞Sleeve cock（10）隔膜阀Diaphragm valve橡胶衬里隔膜阀Rubber lined diaphragm valve直通式隔膜阀Straight-way diaphragm valve堰式隔膜阀Weir diaphragm valve（11）夹紧式胶管阀Pinch valve (用于泥浆，粉尘等)（12）止回阀Check valve升降式止回阀Lift check valve旋启式止回阀Swing check valve; flap check valve落球式止回阀Ball check valve弹簧球式止回阀Spring ball check valve双板对夹式止回阀dual plate wafer type check valve无撞击声止回阀Non-slam check valve底阀Foot valve切断式止回阀Stop check valve, Non-return valve活塞式止回阀Piston check valve斜翻盘止回阀Tilting disc check valve蝶式止回阀Butterfly check valve1.6.3 其它用途的阀安全泄气阀Safety valve [SV]安全泄液阀Relief valve [RV]安全泄压阀Safety relief valve杠杆重锤式Lever and weight type引导阀操纵的安全泄气阀Pilot operated safety valve复式安全泄气阀Twin type safety valve罐底排污阀Flush-bottom tank valve波纹管密封阀Bellow sealed valve电磁阀Solenoid valve; Solenoid operated valve电动阀Electrically operated valve, electric-motor operated valve气动阀Pneumatic operated valve低温用阀Cryogenic service valve蒸汽疏水阀Steam trap机械式疏水阀Mechanical trap浮筒式疏水阀Open bucket trap; open top bucket trap浮球式疏水阀Float trap倒吊桶式疏水阀Inverted bucket trap自由浮球式疏水阀Loose float trap恒温式疏水阀Thermostatic trap金属膨胀式蒸汽疏水阀Metal expansion steam trap液体膨胀式蒸汽疏水阀Liquid expansion steam trap双金属膨胀式蒸汽疏水阀Bi-metallic expansion steam trap压力平衡式恒温疏水阀Balanced pressure thermostatic trap热动力式疏水阀Thermodynamic trap脉冲式蒸汽疏水阀Impulse steam trap放气阀(自动放气阀) Air vent valve (automatic air vent valve)平板式滑动闸阀Slab type sliding gate valve盖阀Flat valve换向阀Diverting valve; Reversing valve热膨胀阀Thermo expansion valve自动关闭阀Self-closing gate valve自动排液阀Self-draining valve管道盲板阀Line-blind valve挤压阀Squeeze valve (用于泥浆及粉尘等)呼吸阀Breather valve风门，挡板Damper减压阀Pressure reducing valve; Reducing valve控制阀Control valve膜式控制阀Diaphragm operated control valve执行机构Actuator背压调节阀Back pressure regulating valve差压调节阀Differential pressure regulating valve压力比例调节阀Pressure ratio regulating valve1.6.4 未指明结构（或阀型）的阀切断阀Block valve; Shut-off valve; Stop valve调节阀Regulating valve快开阀Quick opening valve快闭阀Quick closing valve隔断阀isolating valve三通阀Three-way valve夹套阀Jacketed valve非旋转式阀Non-rotary valve排污阀Blowdown valve集液排放阀Drip valve排液阀Drain valve放空阀Vent valve卸载阀Unloading valve排出阀Discharge valve吸入阀Suction valve多通路阀Multiport valve取样阀Sampling valve手动阀Hand-operated valve; Manually operated valve锻造阀Forged valve铸造阀Cast valve（水）龙头Bibb; Bid; Faucet抽出液阀（小阀—）Bleed valve旁路阀By-pass valve软管阀Hose valve混合阀Mixing valve破真空阀Vacuum breaker冲洗阀Flush valve第一道阀；根部阀Primary valve根部阀Root valve总管阀Header valve事故切断阀Emergency valve1.7 管道特殊件1.7.1 管道特殊件（组件）粗滤器Strainer过滤器Filter临时粗滤器（锥形）Temporary strainer (cone type)Y型粗滤器y-type strainerT型粗滤器T-type strainer永久过滤器Permanent filter丝网粗滤器Gauze strainer洗眼器及淋浴器Eye washer and shower视镜Sight glass阻火器Flame arrester喷嘴，喷头Spray nozzle取样冷却器Sample cooler消声器Silencer膨胀节Expansion joint波纹膨胀节Bellow expansion joint单波Single bellow双波Double bellow多波Multiple bellow压力平衡式膨胀节Pressure balanced expansion带铰链膨胀节Hinged expansion joint轴向位移型膨胀节Axial movement type expansion joint自均衡膨胀节（带外加强环）Self-equalizing expansion joint带接杆膨胀节Tied expansion joint万向型膨胀节Universal type expansion joint球形补偿器Ball type expansion joint; Flexible ball joint填函式补偿器Slip type (packed type) expansion joint单向滑动填料函补偿器Single action packed slip joint1.7.2 管道特殊原件Piping special element软管接头Hose connection [HC]快速接头Quick coupling金属软管Metal hose橡胶管Rubber hose挠性管Flexible tube鞍形补强板Reinforcing saddles补强板Reinforcement pad特殊法兰Special flange漏斗Funnel排液环Drip ring排液漏斗Drain funnel插板Blank垫环Spacer8字盲板Spectacle blind; Figure 8 blind限流孔板Restriction orifice爆破片Rupture disk法兰盖贴面Protective disc费托立克接头Victaulic coupling1.8 端部连接End connection法兰端Flanged end坡口端Beveled end[BE]对焊端Butt welded end平端Plain end [PE]承插焊端Socket welding end螺纹端Threaded end[TE]承口Bell end焊接端Welding end法兰连接（接头）Flanged joint对焊连接（接头）Butt welded joint螺纹连接；管螺纹连接Threaded joint; Pipe threaded joint锥管螺纹密封焊连接Seal-welded taper pipe threaded joint承插焊连接（接头）Socket welded joint承插连接（接头）Bell and spigot joint焊接接头Welded joint; Welding joint环垫接头Ring joint [RJ]万向接头Universal joint软钎焊连接（接头）Soldered joint搭接接头；松套连接Lapped joint外侧厚度切斜角Bevel for outside thickness内侧厚度切斜角Bevel for inside thickness内外侧厚度切斜角Bevel for combined thickness法兰式的Flanged [FLGD]对焊的Butt welded[BW]螺纹的Threaded [THD]承插焊的Socket welded [SW]小端为平的Small end plain [SEP]大端为平的Large end plain[LEP]两端平Both ends plain[BEP]小端带螺纹Small end thread [SET]大端带螺纹large end thread [LET]两端带螺纹Both end thread [BET]一端带螺纹One end thread [OET]支管连接Branch connection焊接支管Branch pipe welded directly to the run pipe 2. 管道用紧固件及螺纹2.1 紧固件螺栓Bolt六角头螺栓Hexagonal head bolt方头螺栓Square head bolt螺柱，双头螺柱Stud bolt环头螺栓Eye bolt沉头螺栓Countersunk (head) screw地脚螺栓Anchor bolt; Foundation bolt松紧螺旋扣（花兰螺丝）TurnbuckleU形螺栓U-boltT形螺栓T-bolt圆头螺钉Round head bolt机螺栓，机螺钉Machine bolt顶开螺栓，顶起螺栓Jack screw自攻螺钉Self-tapping screw膨胀螺栓Expansion bolt粗制的Coarse精制的Finished; fine螺母Nut六角螺母Hexagonal nut方螺母Square nut蝶形螺母Wing nut扁螺母Flat num锁紧螺母Lock num垫圈Washer平垫圈Plain washer球面垫圈Spherical washer弹簧垫圈Spring washer方垫圈Square washer斜垫圈Slant washer销轴Pined shaft销Pin开口销Cotter pin定位销Dowel pin带孔销Pin with hole圆锥销Taper pin铆钉Rivet键Key2.2 螺纹左螺纹Left hand thread右螺纹Right hand thread管螺纹Pipe thread锥管螺纹Taper pipe thread直管螺纹Straight pipe thread梯形螺纹Trapezoid thread螺距Pitch of thread粗牙螺纹Coarse thread细牙螺纹Fine thread特细牙螺纹Extra fine thread通长螺纹Full thread惠氏螺纹Whitworth thread公制螺纹Metric thread美国标准锥管螺纹American standard taper pipe thread [NPT]螺孔Tap3. 材料、型钢及填料3.1 金属材料3.1.1 黑色金属Ferrous metal碳素钢Carbon steel [C.S.]低碳钢Low-carbon steel中碳钢Medium-carbon steel高碳钢High-carbon steel普通碳素钢General carbon steel优质碳素钢High-quality carbon steel普通低合金结构钢General structure low-alloy steel合金结构钢Structural alloy steel合金钢Alloy steel低合金钢Low alloy steel中合金钢Medium alloy steel高合金钢High alloy steel耐热钢Heat resisting steel高强度钢High strength steel复合钢Clad steel工具钢Tool steel弹簧钢Spring steel钼钢Molybdenum steel镍钢Nickel steel铬钢Chromium steel铬钼钢Chromium-nickel steel不锈钢Stainless steel奥氏体不锈钢Austenitic stainless steel马氏体不锈钢martensitic stainless steel司特来合金（钨铬钴合金）Stellite耐蚀耐热镍基合金(哈氏合金) Hastelloy铬镍铁合金Inconel耐热铬镍铁合金Incoloy20合金20 alloy平炉钢（马丁钢）Martin steel镇静钢Killed steel半镇静钢Semi-killed steel沸腾钢Rimmed steel, rimming steel; open-steel锻钢Forged steel铸钢Cast steel铸铁Cast iron [C.I.]灰铸铁Grey cast iron可锻铸铁Malleable iron [MI]球墨铸铁Nodular cast iron; Nodular graphite iron生铁Pig iron熟铁，锻铁Wrought Iron铸件Casting高硅铸铁High silicon cast iron3.1.2 镀层及制造方法渗铬钢，镀铬钢Chromized steel镀铬的Chromium-plated; chrome-plated镀层Plating锻造、型钢Swage锻造的，锻造Forging轧制Rolling热轧Hot rolling冷轧Cold rolling挤压Extruding冷加工Cold working热加工Hot working拔制Drawing3.1.3 有色金属铝Aluminum铜,紫铜Copper黄铜Brass青铜Bronze铝青铜Aluminum bronze磷青铜Phosphor bronze铝镁合金Aluminum magnesium锰青铜Manganese bronze蒙乃尔（注：镍及铜合金）Monel镍铜合金Nickel copper alloy非铁合金Nonferrous alloy钛Titanium铅Lead硬铅Hard lead3.1.4 材料性能极限强度Ultimate strength抗拉强度Tensile strength屈服极限Yield limit屈服点Yield point延伸率Percentage elongation抗压强度Compressive strength抗弯强度Bending strength弹性极限Elastic limit冲击值Impact value疲劳极限Fatigue limit蠕变极限Creep limit持久极限Endurance limit布氏硬度Brinell hardness洛氏硬度Rockwell hardness维氏硬度Vickers diamond hardness; Diamond penetrator hardness蠕变断裂强度Creep rupture strength断面收缩率Reduction of area韧性Toughness脆性Brittleness延性Ductility冷脆Cold shortness冷流Cold flow3.2 非金属材料塑料Plastic丙烯腈-丁二烯-苯乙烯Acrylonitrile-butadiene-styrene[ABS]聚乙烯Polyethylene [PE]聚氯乙烯Polyvinyl chloride [PVC]苯乙烯橡胶Styrene-rubber [SR]聚丁烯Polybutylene[PB]聚丙烯Polypropylene [PP]聚苯乙烯Polystyrene [PS]氯化聚醚Chlorinated polyether [CPE]聚酰胺Polyamide[PA]聚碳酸酯Polycarbonate [PC]聚甲基丙烯酸甲酯Polymethyl methacrylate [PMMA]醋酸丁酸纤维素Cellulose acetate butyrate [CAB]氯化聚氯乙烯Chlorinated polyvinyl chloride [CPVC]聚偏二氟乙烯Polyvinylidene fluoride [PVDF]缩醛塑料Acetal plastic尼龙塑料Nylon plastic聚烯烃Polyolefin [PO]石墨酚醛塑料Graphite phenolic plastics聚四氟乙烯Polytetrafluoroethylene [PTFE]纤维增强热塑性塑料Fiber reinforced thermoplastics热塑性塑料Thermoplastic热固性塑料Thermosetting plastics胶粘剂Adhesive溶剂胶接剂Solvent cement树脂Resin环氧树脂Epoxy resin聚酯树脂Polyester resin聚酯纤维Polyester fibers氟塑料Fluoroplastics聚氨基甲酸酯Polyurethane丙烯酸树脂Acrylic resin脲醛树脂Urea resin呋喃树脂Furan resin乙稀丙烯二烃单体Ethylene propylene diene monomer [EPDM]合成橡胶Synthetic rubber橡胶Rubber丁腈橡胶Nitrile butadiene rubber氯丁橡胶Neoprene天然橡胶Natural rubber乙丙橡胶Ethylene propylene rubber [EPR]玻璃Glass硼硅玻璃Borosilicate glass耐火砖Fire brick陶瓷Ceramic搪瓷Porcelain enamel木材Wood3.3 型材型钢Shaped steel; Section steel; Swage角钢Angle steel槽钢Channel工字钢I-beam宽缘工字钢或H钢Wide flanged beamT型钢T-bar方钢Square bar扁钢Flat bar六角钢Hexagonal steel bar圆钢Round steel; Rod钢带Strap steel钢板Plate网纹钢板Checkered plate腹板（制定钢的立板）Web翼缘Wing3.4 填料及填料函填料Packing石棉绳Asbestos rope; Asbestos cordO形环O-ring自密封Self-sealing四氟带Teflon tap带铬镍合金丝的石棉绳Asbestos rope with inconel wire; Inconel wireasbestos浸聚四氟乙烯的石棉填料Teflon impregnated asbestos packing金属填料Metallic stuffing填料箱，填料函Packing box; Stuffing box填料函压盖Stuffing box gland4. 管道等级及材料统计4.1 管道材料规定Piping material specification管道等级Piping class; Piping classification管道等级号Class designation公称直径Nominal diameter[DN]; Nominal (pipe) size公称压力Nominal pressure[PN]压力级；等级；类别Class [CL]低压Low pressure[L.P.]中压Medium pressure [M.P.]高压High pressure [H.P.]大气压Atmosphere [ATM]真空Vacuum工作压力Operating pressure; Working pressure设计压力Design pressure工作温度Operating temperature设计温度Design temperature环境温度Ambient temperature腐蚀裕量Corrosion allowance管道附件Piping attachment管道元件Piping element壁厚Wall thickness[WT]壁厚系列号Schedule number [SCH.No]加厚的，加强的Extra heavy; Extra strong双倍加厚的，双倍加强的Double extra heavy; Double extra strong通用连接组Typical installation分组（类）形式（如管道等级表）Block form数据库Data base文件File4.2 材料统计Material take-off [MTO]汇总表Summary sheet材料表Bill of material[BM]综合管道材料表Consolidated piping material summary sheet [CPMSS]统计材料准确度Accuracy of take-off材料情况报告Material status report散装材料Bulk material编位号的Itemized代码Code number短代码Short code数量Quantity [QTY]重力Weight净重Net weight毛重Cross weight5．设备布置及管道布置Plot plan and piping layout; Equipment and piping arrangement5.1 设备名称Equipment name5.1.1 容器Vessel（1）塔Tower; Column洗涤塔Scrubber吸收塔Absorber冷却塔Cooling tower精馏塔Fractionating tower蒸馏塔Distillation tower再生塔Regenerating tower造粒塔Prilling tower汽提塔Stripper脱气塔Degasifier合成塔Synthesis tower（2）反应器Reactor聚合釜Polymerizer转化器；变换器Converter脱硫反应器Desulphurization reactor甲烷化器Methanator（3）气柜Gas-holder螺旋式气柜helical gas-holder湿式气柜Wet gas-holder干式气柜Dry gas-holder（4）槽罐储罐Tank; Storage tank缓冲罐Knock out drum球罐Spheroid; Spherical tank罐Drum接受槽Receiver计量槽Measuring tank加料槽Feed tank排污罐Blow down tank闪蒸罐Flash drum汽包Steam drum溶液贮槽solution storage tank地下槽Slop tank（5）其他设备分离器Separator旋风分离器Cyclone分子筛Molecular sieve脱氧器Deaerator搅拌器Agitator干燥器Dryer混合器Mixer萃取器Extractor结晶器Crystallizer澄清器Gravity settler净化器Purifier气化器Vaporizer吸附器Adsorber融解槽Melter减温器Desuperheater升压器Booster喷射器Ejector喷头Sprayer火炬Flare消声器Silencer（6）换热器、加热器、冷却器换热器Heat exchanger空冷器Air cooler水冷却器Water cooler冷凝器Condenser螺旋板式换热器Spiral plate heat exchanger蒸发器Evaporator再沸器Reboiler急冷器Quencher深冷器Chiller预热器Preheater再热器Reheater加热器Heater电加热器Electric heater过热器Super heater给水加热器Feed water heater中间冷却器Inter cooler后冷却器After cooler5.1.2 工业炉及锅炉炉子Furnace烧咀Burner锅炉Boiler烟囱Stack废热锅炉Wasteheat boiler辅助锅炉Auxiliary boiler省煤器Economizer回热炉Direct-fired heater辐射段Radiant section对流段Convection section裂化炉Reformer焚烧炉Incinerator回转窑Rotary kiln炉管Furnace tube吹灰器Soot blower观察孔Observation door; Peep door防爆门Explosion door5.1.3 转动机器（1）泵Pump涡轮泵Turbine pump涡流泵Vortex pump离心泵Centrifugal pump喷射泵Jet pump转子泵；旋转泵Rotary pump管道泵Inline pump真空泵Vacuum pump柱塞泵Plunger pump往复泵Reciprocating pump计量泵Metering pump深井泵Deep well pump齿轮泵Gear pump手摇泵Hand-pump; Wobble pump锅炉给水泵Boiler feed water pump轴流泵Axial pump（2）压缩机Compressor往复式压缩机Reciprocating compressor多级压缩机Multiple stages compressor螺杆压缩机Helical screw compressor离心式压缩机Centrifugal compressor循环压缩机Circulating compressor涡轮压缩机Turbo compressor冷冻机Refrigerator（3）驱动机、发电机汽轮机、蒸汽透平Steam turbine燃气轮机Gas turbine电动机Motor发电机Generator（4）风扇、鼓风机风机Fan鼓风机Blower罗茨鼓风机Roots blower（5）其他机器挤压机Extruder造粒机Pelletizer离心机Centrifuger离心分离机Centrifugal separator离心过滤机Centrifugal filter压滤机pressure filter5.1.4 储运、装卸及起重机械起重机Crane桥式起重机Bridge crane电动葫芦Motor hoist手动葫芦；倒链Chain block装卸臂Loading arm,料仓Silo; Bin料斗Hopper输送机Conveyor皮带输送机Belt conveyor5.2 辅助用房名称5.2.1 生产用房分析室Analyzer room变压器室Transformer room配电室；变电所Substation; Switch room蓄电池室Battery room控制室Control room通风室Ventilating room贮藏室Storage room维修间Maintenance room办公室Office5.2.2 生活用房更衣室Locker room盥洗室；厕所Closet; Lavatory; Toilet5.3 图名管道布置平面Piping arrangement plan[PAP]管道布置Piping layout轴测图Isometric drawing分区索引图Key plan初版设备布置图（“A”版）Preliminary plot plan (“A” Issue)内部审查版设备布置图（“B”版）Internal approval plot plan (“B” Issue)用户审查版设备布置图（“C”版）Owner approval plot plan (“C” Issue)确认版设备布置图（“D”版）Confirm plot plan (“D” Issue)研究版设备布置图（“E”版）Planning plot plan (“E” Issue)设计版设备布置图（“F”版）Designing plot plan (“F” Issue)施工版设备布置图（“G”版）Construction plot plan (“G” Issue)5.4 厂房、站、单元压缩机房Compressor house (room)泵房Pump house (room)洗眼站Eye washer station泡沫站Foam station软管站；公用工程站Hose station; Utility station成套设备Package unit设施Facilities罐区Tank yard空分装置Air separation facility5.5 设备布置设备位号Equipment item number工厂Plant工厂区界Plant limit项目区界内侧Inside battery limit [ISBL]项目区界Battery limit [BL]区界Area limit区域边界Zone limit界外Offsite东East [E]西West[W]南South[S]北North[N]上Up下Down工厂北向Plant north真实北向True north道路Road小过道Cat walk; Cat way走道；过道Walk way; Gangway; Access way污水坑（井）Sump pit集水池Catch basin沟槽Trough预留区Future area场地Yard铺砌区Paving area非铺砌区Unpaved area碎石铺面Gravel paving橡皮铺面Rubber paving面积；区域Area体积；容积Volume [VOL]5.6 管道布置管道设计Piping design管道研究Piping design走向研究Routing study重要管道Critical piping地上管道Above ground piping地下管道Under ground piping管网Network of pipes管廊Pipe rack管沟Piping trench管间距Line spacing管道跨距Line span总管Header; Manifold旁路By pass排液Drain放空Vent上升管；垂直管Riser导管Conduit裸管Bare line管件直接Fitting to fitting[FTF]管段；接口Spool piece; Spool取样接口Sampling connection集液包Drip leg伴热管Tracing pipe蒸汽伴热Steam tracing热水伴热Hot-water tracing电伴热Electrical tracing夹套管Jacketed line; Jacketed piping 全夹套的Full Jacketed平面Plan详图Detail“X”视图View “X”“A-A”剖视Section “A-A”连接图Hook up drawing接续图Continue on drawing [COD] 接续线Match line[M.L.]比例Scale图例Legend符号Symbol管口表List of nozzles方位Orientation管口方位Nozzle orientation定位Location相交Intersection水平的Horizontal垂直的，立式的Vertical垂直；正交；垂直的Perpendicular平行；平行的Parallel水平安装Horizontal installation垂直安装Vertical installation对称的Symmetric相反（的）；对面（的）Opposite顺时针方向Clockwise逆时针方向Counter-clock wise计算机辅助设计Computer aided design [CAD] 5.7 图面标注绝对标高Absolute elevation海平面标高Over-sea mean level[OSL]标高；立面Elevation [EL]混凝土顶面Top of concrete架顶面Top of support [TOS]钢结构顶面Top of steel梁顶面Top of beam[TOB]支撑点Point of support [POS]管顶Top of pipe [TOP]管底Bottom of pipe[BOP]沟底Bottom of trench管子内底Invert (Inside bottom of pipe)底平Flat on bottom [FOB]顶平Flat on top [FOT]工作点Working point [W.P.]面至面Face to face[F-F]中心至端面Center to end [C-E]中心至面Center to face [C-F}中心至中心；中至中Center to Center [C-C]坐标Coordinate坐标原点Origin of coordinate出口中心线Center line of discharge入口中心线Center line of suction中心线Center line[CL]入口Inlet; Suction出口Outlet; Discharge排出口Exhaust距离Distance直径Diameter[D]; [DIA]半径Radius [R]外径Outside diameter [OD]内径Inside diameter[ID]净空Head room间隙Clearance尺寸Dimension高度Height高度；海拔Altitude厚度Thickness[THK]长度Length宽度Width深度Depth坡度Slope相当的；当量的Equivalent最大Maximum [Max.]最小Minimum [Min.]大约Approximate [APPROX]管线号Line number等级分界Material specification break隔热分界Insulation break未经允许不得开启Car seal close [C.S.C.]未经允许不得关闭Car seal open [C.S.O.]在关闭状态下锁定Locked closed [LC]在开启状态下锁定Locked opened [LO]由买方供货By buyer [BB]由卖方供货By seller [BS]由制造厂供货By vendor [BV]标记号Tag number公差Tolerance允差Allowance误差Error直度Straightness5.8 相关专业的专业词汇5.8.1 工艺（1）图及表流程图Flow diagram工艺流程图Process flow diagram [PFD]管道及仪表流程图Piping and instrument flow diagram [PID]公用工程流程图Utility flow diagram [UFD]管线表Line list; Line schedule命名表；管道表Nomenclature设备表Equipment list (Schedule)（2）流体Fluid空气Air仪表空气Instrument air工艺空气Process air低压蒸汽Low pressure steam中压蒸汽Medium pressure steam高压蒸汽High pressure steam伴热蒸汽Tracing steam饱和蒸汽Saturated steam过热蒸汽Superheated steam氧气Oxygen氢气Hydrogen氮气Nitrogen燃料气Fuel gas天然气Natural gas火炬气Flare gas酸性气Sour gas液化石油气Liquefied petroleum gas [LPG]氨气Ammonia gas冷却水Cooling循环水Circulating water锅炉给水Boiler feed water热水Hot water蒸汽冷凝水Steam condensate盐水Brine工艺水Process water化学污水Chemical sewage防腐剂Corrosion inhibitor重油Heavy oil石脑油Naphtha燃料油Fuel oil润滑油Lubricating oil密封油Sealing oil冷冻剂Refrigerant载热体Heating medium溶剂Solvent溶液Solution母液Mother liquor单体Monomer聚合物Polymer均聚物Homopolymer共聚物Copolymer工艺液体Process liquid工艺气体Process gas硫酸Sulfuric acid盐酸Hydrochloric acid硝酸Nitric acid烧碱Caustic soda（3）流体特性Fluid characteristics蒸汽压Vapor pressure临界温度Critical temperature临界点Critical point临界压力Critical pressure比热Specific heat湿度humidity密度Density比重Specific gravity粘度Viscosity闪点Flash point融点Melting point凝固点Freezing point浓度Concentration爆炸极限Limit of explosion有毒的Toxic可燃的，易燃的Flammable（4）其它回收Recovery再生Regeneration循环Circulation再循环；再生Recycle补充Make-up制备Preparation蒸汽吹扫Steaming out吹扫Purge抽空；排空Evacuation吹出Blow-off排污Blow down破真空Vacuum breaker大气腿Barometric leg备用Stand-by化学清洗Chemical cleaning净正吸入压头Net positive suction head [NPSH]进料Feed成品Product污染Contamination大气污染Atmospheric pollution环境温度Ambient temperature5.8.2 建筑、结构建筑物Building钢结构Steel structure已有钢结构Existing steel structure钢筋混凝土结构Reinforced concrete construction楼面Floor平台Platform [PF]地面Ground level栏杆Handrail楼梯Stair; Stair way直梯Ladder柱Column; Post; Stanchion基础Foundation; Footing梁Beam斜撑;支撑Bracing桁架；主梁Girder构件Member隔墙Partition wall墙Wall篦子板Grate; Grating吊装孔Erection opening吊梁Hoisting beam棚Shelter窗Window天窗Skylight门Door防火门Fire door地漏Floor drain防火层Fire-proofing总图General plot plan路肩Shoulder桩Pile灌浆Grouting风荷载Wind load雪荷载Snow load动力荷载Dynamic load静荷载Dead load活荷载Live load风速Wind Velocity主导风向Most frequent wind direction5.8.3 仪表盘（操作盘）Panel就地盘Local panel仪表盘Instrument panel常开Normally open常闭Normally closed电缆槽（架）Cable tray (Channel); Cable rack仪表电缆槽（架）Instrument cable tray (Duct)压力计Manometer; Pressure gauge热电偶Thermocouple温度计Thermometer液位计Level gauge玻璃液位计Ga(u)ge glass温度计保护管Thermowell流量计Flow meter孔板Orifice变送器Transmitter联锁Interlock。
管道工程英文术语缩写
管道工程英文术语缩写（中英对照）1.管子及管件P 管子 PipeEL 弯头ELL 长半径弯头ELS 短半径弯头MEL 斜接弯头（虾米腰弯头）REL 异径弯头T 三通 TeeLT 斜三通RT 异径三通R 异径管接头（大小头） ReducerCR 同心异径管接头（同心大小头） Concentric reducer ER 偏心异径管接头（偏心大小头） Eccentric reducer CPL 管箍 CouplingFCPL 双头管箍 Full couplingHCPL 单头管箍 Half couplingRCPL 异径管箍 Reducing couplingBU 内外螺纹接头 BushingUN 活接头 UnionHC 软管接头 Hose couplerSE 翻边短节 Stub endNIP 短节 Pipe nipple or straight nippleSNIP 异径短节 Swaged nippleCP 管帽（封头） CapPL 管堵（丝堵） PlugBLK 盲板 BlankSB 8字盲板 Spectacle blind (blank)RP 补强板 Reinforcing pad2.法兰 FLG 法兰 FlangeWNF 对焊法兰 Welding neck flangeSOF 平焊法兰 Slip-on flangeSWF 承插焊法兰 Socket-welding flangeT 螺纹法兰 Threaded flangeLJ 松套法兰 Lapped joint flangeREDF 异径法兰 Reducing flangeBF 法兰盖（日法兰） Blind flangeFSF 法兰密封面 Flange scaling FF 全平面 Flat face RF 凸台面 Raised faceMFF 凹凸面 Male and female faceLF 凹面 Female faceLM 凸面 Male faceRJ 环连接面 Ring joint faceTG 榫槽面 Tongue and groove faceTF 榫面 Tongue faceGF 槽面 Groove face3.垫片 G 垫片 GasketNMG 非金属垫片 Non-metallic gasketAG 石棉垫片 Asbestos gasketRG 橡胶垫片 Rubber gasketTEG 聚四氟乙烯包复垫片 PTFE envelope gasketSMG 半金属垫片 Semimetallic gasketMJG 金属包垫片 Meta-jacket gasketSWG 缠绕式垫片 Spiral wound gasketMG 金属垫片 Metallic gasketFMG 金属平垫片 Flat metallic gasketSMSG 齿形金属垫片 Solid metal serrated gasketLER 透镜式金属环垫 Lens ring gasketOCR 八角形金属环垫 Octagonal ring gasketOVR 椭圆形金属环垫 Oval ring gaksetIR/OR 内外定位环 Inner ring and outer ringIR 内定位环 Inner ringOR 外定位环 Outer ring4.坚固件 B 螺栓 BoltSB 螺柱 Stud boltNU 螺母 NutTB 花蓝螺母 TurnbuckleWSR 垫圈 WasherSWSR 弹簧垫圈 Spring washer5.阀门 GV 闸阀 Gate valveGLV 截止阀 Globe valveCHV 止回阀 Check valveBUV 蝶阀 Butterfly valveBAV 球阀 Ball valvePV 旋塞阀 Plug valve (cock)CV 调节阀 Control valveSV 安全阀 Safety valveRV 减压阀 Pressure reducing valveST 蒸汽疏水阀 Steam trapPRV 泄压阀 Pressur relief valveBV 呼吸阀 Breather valveNV 针形阀 Needle valveAV 角阀DV 隔膜阀TWV 三通阀SGV 插板阀6.管道上用的小型设备 SPR 气液分离器 Separator FA 阻火器 Flame arresterSR 过滤器 StrainerSRY Y型过滤器 Y-type strainerSRT T型过滤器 T-type strainerSRB 桶式过滤器 Bucket type strainerTSR 临时过滤器 Temporary strainerSIL 消声器 SilencerSG 视镜 Slight glassSC 取样冷却器 Sample coolerDF 排液漏斗 Drain funnelLM 管道混合器 Line mixerRO 限流孔板 Restriction orificeMO 混合孔板 Mixing orificeRD 爆破片（爆破膜） Rupture diskEJ 补偿器 Expansion joint7.隔热、伴热 INS 隔热 Thermal insulationH 保温 Hot insulationC 保冷 Cold insulationP 防烫伤隔热 Personnel protection insulationT&I 伴热 Tracing and insulationT 管道伴热（冷） TracingEST 蒸汽外伴热 External steam tracingIST 蒸汽内伴热 Internal steam tracingSJT 蒸汽夹套伴热 Steam-jacket tracingET 电伴热 Electric tracing8.配管材料和等级 M 金属材料 Metallic material CS 碳钢 Carbon steelCAS 铸钢 Cast steelFS 锻钢 Forged steelAS 合金钢 Alloy steelSS 不锈钢 Stainless steelAUSTSS 奥氏体不锈钢 Austenitic stainless-steelCI 铸铁 Cast ironMI 可锻铸铁 Malleable ironDI 球墨铸铁 Ductile ironAL 铝 AluminumBRS 黄铜 BrassBRZ 青铜 BronzeCU 紫铜 CopperLAS 低合金钢 Low alloy steelFLAS 低合金锻钢 Forged low alloy steelCLAS 低合金铸钢 Cast low alloy steelTHK 壁厚 ThicknessSCH 表号 Schedule numberSTD 标准 StandardXS 加强 Extra strongXXS 特强 Double extra strong9.装置布置 CN 建北 Construction northE 东 EastW 西 WestS 南 SouthN 北 NorthH 水平 HorizontalV 竖直、铅直、直立 VerticalGRD 地坪 GroundUG 地下 UndergroundBL 装置边界线 Battery limit lineESEW 事故沐浴洗眼器 Emergency shower and eye washer HS 软管站 Hose stationML 接续分界线 Match linePS 管道支架（管架） Piping supportPR 管桥 Pipe rackSTRU 构架（构筑物） StructureBLDG 建筑物 BuildingPD 清扫设施 Purge devicePT 池 PitSHLT 棚 ShelterCOFF 围堰 CofferdamFL 楼板 FloorPF 平台 Plateform10.尺寸标注 EL 标高 Elevation BOP 管底 Bottom of pipeCOP 管中心Center of pipeTOP 管顶 Top of pipeFOB 底平 Flat on bottomFOT 顶平 Flat on topCL(屯) 中心线 Center lineTL 切线 Tangent lineSYM 对称的 SymmetricalBOS 支架底 Bottom of supportTOS 支架顶 Top of supportCL 净距（净空） ClearanceCTC 中心至中心 Center to centerCTF 中心至面 Center to faceCTE 中心至端部 Center to endETE 端到端 End to endFEF 法兰端面 Flange and faceFTF 面到面 Face to faceD 直径 DiameterDN 公称直径 Nominal diameterID 内径 Inside diameterOD 外径 Outside diameterDIM 尺寸 DimensionMAX 最大 MaximumMIN 最小 MinimumAVG 平均 AverageAPP 约、近似 Approximate点标高 Point elevation11.图表 PFD 工艺流程图 Process flow diagramPID 管道和仪表流程图 Piping & instrument diagramCOD 接续图 Continued on drawingDTL 详图 DatailSPDWG(ISODWG) 管段图 Spool drawing (each line isometric drawing) DWGNO 图号 Drawing numberDWGI 所在图号 Drawing identificationLOW 材料表 List of materialMTO 汇料 Material take-offAPPX 附录 AppendixJOB. No. 工号 Job NumberBEDD 基础工程设计数据 Basic engineering design dataDEDD 详细工程设计数据 Detail engineering design dataREV. No. 修改号 Recision numberREFDWG 参考图 Reference drawingSC 采样接口 Sample connection12.操作方式及工作参数 AUT 自动 AutomaticML 手动 Manual controlCHOP 链条操作 Chain operatedCSC 铅封关 Car seal closeCSO 铅封开 Car seal openLC 锁闭 Lock closedLO 锁开 Lock openNC 正常关 Normally closeNO 正常开 Normally openATM 大气压 AtmospherePN 公称压力 Nominal pressureA 绝压G 表压(T) 温度 Temperature(P) 压力 Pressure13.施工 W 焊接 WeldingAW 电弧焊 Arc weldingGSAW 气体保护电弧焊 Gas shielded-acr welding EFW 电熔焊 Elecric fusion weldingERW 电阻焊 Electric Resistance weldingGW 气焊 Gas weldingLW 搭接焊 Lap weldingBW 对焊 Butt weldingTW 定位焊 Tack weldingSW 承插焊 Socket weldingCW 连续焊 Continuous weldingSEW 密封焊 Seal weldingSFG 堆焊 SurfacingFW 现场焊接 Field weldingHT 热处理 Heat treatmentPH 预热 PreheatingSR 应力消除 Stress reliefPWHT 焊后热处理 Post weld heat treatmentEIT 检查、探伤和实验 Examination, inspection & testing VE 外观检查 Visual examinationUI (UT) 超声探伤 Ultrasonic inspection (test)RI (RT) 射线探伤 Radiographic inspection (test)MPI (MT) 磁粉探伤 Magnetic particle inspection (test)LPI (PT) 液体渗透检验 Liquid penterant inspection (test) HADT 硬度实验 Hardness testingHYDT 水压实验 Hydraulic testingPNET 气压实验 Pneumatic testingCE 焊条 Covered electrodeWW 焊丝 Welding wireASSY 装配、组合 AssemblyF 现场 FieldF/F 现场制造 Field faricatedSF 现场决定 Suit in fieldCSP 冷紧 Cold springBCT 螺栓冷紧 Bolt cold tighteningBHY 螺栓热紧 Bolt hot tighteningCO 清洗口 Clean outANNY 退火 AnnealedPE 平端面 Plain endBE 坡口端 Belelled endTHR 螺纹 ThreadHB 布氏硬度 Brinnel hardnessRC 洛氏硬度14.其他 FDN 基础 FoundationINF 信息（资料） InformationREF 参考 ReferenceREV 修改 RevisionSEQ 序号（顺序） SequenceW/E 设备带来 With equipmentW/I 仪表带来 With instrumentCM 色标 Colour markCA 腐蚀裕度 Corrosion allowanceUTL 公用系统 UtilityUC 公用工程接头 Utility connectionQTY 数量 QuantityWT 重量 WeightMHR 工时 Man hourBC 螺栓分布圆 Bolt circleHP 高点 High pointLP 低点Low pointSUC 吸入（口） SuctionDIS 排出（口） DischargeSO 蒸气吹扫（口） Steam outNPT 美国标准锥管螺纹 National standard taper pipe threadNPS 美国标准直管螺纹 National standard straight pipe thread DR 排液 DrainVT 放气 VentRTG （压力）等级 RatingCL 等级 ClassSMLS 无缝 Seamless螺旋缝。
管道工程英文术语缩写
管道工程英文术语缩写管道工程英文术语缩写（中英对照）1.管子及管件P 管子 PipeEL 弯头ELL 长半径弯头ELS 短半径弯头MEL 斜接弯头（虾米腰弯头）REL 异径弯头T 三通 TeeLT 斜三通RT 异径三通R 异径管接头（大小头） ReducerCR 同心异径管接头（同心大小头） Concentric reducer ER 偏心异径管接头（偏心大小头） Eccentric reducer CPL 管箍 Coupling FCPL 双头管箍 Full couplingHCPL 单头管箍 Half couplingRCPL 异径管箍 Reducing couplingBU 内外螺纹接头 BushingUN 活接头 UnionHC 软管接头 Hose couplerSE 翻边短节 Stub endNIP 短节 Pipe nipple or straight nippleSNIP 异径短节 Swaged nippleCP 管帽（封头） CapPL 管堵（丝堵） PlugBLK 盲板 BlankSB 8字盲板 Spectacle blind (blank)RP 补强板 Reinforcing pad2.法兰 FLG 法兰 FlangeWNF 对焊法兰 Welding neck flangeSOF 平焊法兰 Slip-on flangeSWF 承插焊法兰 Socket-welding flangeT 螺纹法兰 Threaded flangeLJ 松套法兰 Lapped joint flangeREDF 异径法兰 Reducing flangeBF 法兰盖（日法兰） Blind flangeFSF 法兰密封面 Flange scaling FF 全平面 Flat face RF 凸台面Raised faceMFF 凹凸面 Male and female faceLF 凹面 Female faceLM 凸面 Male faceRJ 环连接面 Ring joint faceTG 榫槽面 T ongue and groove faceTF 榫面 T ongue faceGF 槽面 Groove face3.垫片 G 垫片 GasketNMG 非金属垫片 Non-metallic gasketAG 石棉垫片 Asbestos gasketRG 橡胶垫片 Rubber gasketTEG 聚四氟乙烯包复垫片 PTFE envelope gasketSMG 半金属垫片 Semimetallic gasketMJG 金属包垫片 Meta-jacket gasketSWG 缠绕式垫片 Spiral wound gasketMG 金属垫片 Metallic gasketFMG 金属平垫片 Flat metallic gasketSMSG 齿形金属垫片 Solid metal serrated gasketLER 透镜式金属环垫 Lens ring gasketOCR 八角形金属环垫 Octagonal ring gasketOVR 椭圆形金属环垫 Oval ring gaksetIR/OR 内外定位环 Inner ring and outer ringIR 内定位环 Inner ringOR 外定位环 Outer ring4.坚固件 B 螺栓 BoltSB 螺柱 Stud boltNU 螺母 NutTB 花蓝螺母 TurnbuckleWSR 垫圈 WasherSWSR 弹簧垫圈 Spring washer5.阀门 GV 闸阀 Gate valveGLV 截止阀 Globe valveCHV 止回阀 Check valveBUV 蝶阀 Butterfly valveBAV 球阀 Ball valvePV 旋塞阀 Plug valve (cock)CV 调节阀 Control valveSV 安全阀 Safety valveRV 减压阀 Pressure reducing valveST 蒸汽疏水阀 Steam trapPRV 泄压阀 Pressur relief valveBV 呼吸阀 Breather valveNV 针形阀 Needle valveAV 角阀DV 隔膜阀TWV 三通阀SGV 插板阀6.管道上用的小型设备SPR 气液分离器Separator FA 阻火器Flame arresterSR 过滤器 StrainerSRY Y型过滤器 Y-type strainerSRT T型过滤器 T-type strainerSRB 桶式过滤器 Bucket type strainerTSR 临时过滤器 Temporary strainerSIL 消声器 SilencerSG 视镜 Slight glassSC 取样冷却器 Sample coolerDF 排液漏斗 Drain funnelLM 管道混合器 Line mixerRO 限流孔板 Restriction orificeMO 混合孔板 Mixing orificeRD 爆破片（爆破膜） Rupture diskEJ 补偿器 Expansion joint7.隔热、伴热 INS 隔热 Thermal insulationH 保温 Hot insulationC 保冷 Cold insulationP 防烫伤隔热 Personnel protection insulationT&I 伴热 Tracing and insulationT 管道伴热（冷） TracingEST 蒸汽外伴热 External steam tracingIST 蒸汽内伴热 Internal steam tracingSJT 蒸汽夹套伴热 Steam-jacket tracingET 电伴热 Electric tracing8.配管材料和等级 M 金属材料 Metallic material CS 碳钢 Carbon steelCAS 铸钢 Cast steelFS 锻钢 Forged steelAS 合金钢 Alloy steelSS 不锈钢 Stainless steelAUSTSS 奥氏体不锈钢 Austenitic stainless-steelCI 铸铁 Cast ironMI 可锻铸铁 Malleable ironDI 球墨铸铁 Ductile ironAL 铝 AluminumBRS 黄铜 BrassBRZ 青铜 BronzeCU 紫铜 CopperLAS 低合金钢 Low alloy steelFLAS 低合金锻钢 Forged low alloy steelCLAS 低合金铸钢 Cast low alloy steelTHK 壁厚 ThicknessSCH 表号 Schedule numberSTD 标准 StandardXS 加强 Extra strongXXS 特强 Double extra strong9.装置布置 CN 建北 Construction northE 东 EastW 西 WestS 南 SouthN 北 NorthH 水平 HorizontalV 竖直、铅直、直立 VerticalGRD 地坪 GroundUG 地下 UndergroundBL 装置边界线 Battery limit lineESEW 事故沐浴洗眼器 Emergency shower and eye washer HS 软管站 Hose stationML 接续分界线 Match linePS 管道支架（管架） Piping supportPR 管桥 Pipe rackSTRU 构架（构筑物） StructureBLDG 建筑物 BuildingPD 清扫设施 Purge devicePT 池 PitSHLT 棚 ShelterCOFF 围堰 CofferdamFL 楼板 FloorPF 平台 Plateform10.尺寸标注 EL 标高 Elevation BOP 管底 Bottom of pipe COP 管中心Center of pipeTOP 管顶 Top of pipeFOB 底平 Flat on bottomFOT 顶平 Flat on topCL(屯) 中心线 Center lineTL 切线 Tangent lineSYM 对称的 SymmetricalBOS 支架底 Bottom of supportTOS 支架顶 Top of supportCL 净距（净空） ClearanceCTC 中心至中心 Center to centerCTF 中心至面 Center to faceCTE 中心至端部 Center to endETE 端到端 End to endFEF 法兰端面 Flange and faceFTF 面到面 Face to faceD 直径 DiameterDN 公称直径 Nominal diameterID 内径 Inside diameterOD 外径 Outside diameterDIM 尺寸 DimensionMAX 最大 MaximumMIN 最小 MinimumAVG 平均 AverageAPP 约、近似 Approximate点标高 Point elevation11.图表 PFD 工艺流程图 Process flow diagramPID 管道和仪表流程图 Piping & instrument diagramCOD 接续图 Continued on drawingDTL 详图 DatailSPDWG(ISODWG) 管段图 Spool drawing (each line isometric drawing) DWGNO 图号 Drawing numberDWGI 所在图号 Drawing identificationLOW 材料表 List of materialMTO 汇料 Material take-offAPPX 附录 AppendixJOB. No. 工号 Job NumberBEDD 基础工程设计数据 Basic engineering design dataDEDD 详细工程设计数据 Detail engineering design dataREV. No. 修改号 Recision numberREFDWG 参考图 Reference drawingSC 采样接口 Sample connection12.操作方式及工作参数 AUT 自动 AutomaticML 手动 Manual controlCHOP 链条操作 Chain operatedCSC 铅封关 Car seal closeCSO 铅封开 Car seal openLC 锁闭 Lock closedLO 锁开 Lock openNC 正常关 Normally closeNO 正常开 Normally openATM 大气压 AtmospherePN 公称压力 Nominal pressureA 绝压G 表压(T) 温度 Temperature(P) 压力 Pressure13.施工 W 焊接 WeldingAW 电弧焊 Arc weldingGSAW 气体保护电弧焊 Gas shielded-acr welding EFW 电熔焊Elecric fusion weldingERW 电阻焊 Electric Resistance weldingGW 气焊 Gas weldingLW 搭接焊 Lap weldingBW 对焊 Butt weldingTW 定位焊 Tack weldingSW 承插焊 Socket weldingCW 连续焊 Continuous weldingSEW 密封焊 Seal weldingSFG 堆焊 SurfacingFW 现场焊接 Field weldingHT 热处理 Heat treatmentPH 预热 PreheatingSR 应力消除 Stress reliefPWHT 焊后热处理 Post weld heat treatmentEIT 检查、探伤和实验 Examination, inspection & testing VE 外观检查 Visual examinationUI (UT) 超声探伤 Ultrasonic inspection (test)RI (RT) 射线探伤 Radiographic inspection (test)MPI (MT) 磁粉探伤 Magnetic particle inspection (test)LPI (PT) 液体渗透检验 Liquid penterant inspection (test) HADT 硬度实验 Hardness testingHYDT 水压实验 Hydraulic testingPNET 气压实验 Pneumatic testingCE 焊条 Covered electrodeWW 焊丝 Welding wireASSY 装配、组合 AssemblyF 现场 FieldF/F 现场制造 Field faricatedSF 现场决定 Suit in fieldCSP 冷紧 Cold springBCT 螺栓冷紧 Bolt cold tighteningBHY 螺栓热紧 Bolt hot tighteningCO 清洗口 Clean outANNY 退火 AnnealedPE 平端面 Plain endBE 坡口端 Belelled endTHR 螺纹 ThreadHB 布氏硬度 Brinnel hardnessRC 洛氏硬度14.其他 FDN 基础 FoundationINF 信息（资料） InformationREF 参考 ReferenceREV 修改 RevisionSEQ 序号（顺序） SequenceW/E 设备带来 With equipmentW/I 仪表带来 With instrumentCM 色标 Colour markCA 腐蚀裕度 Corrosion allowanceUTL 公用系统 UtilityUC 公用工程接头 Utility connectionQTY 数量 QuantityWT 重量 WeightMHR 工时 Man hourBC 螺栓分布圆 Bolt circleHP 高点 High pointLP 低点Low pointSUC 吸入（口） SuctionDIS 排出（口） DischargeSO 蒸气吹扫（口） Steam outNPT 美国标准锥管螺纹 National standard taper pipe thread NPS 美国标准直管螺纹 National standard straight pipe thread DR 排液 DrainVT 放气 VentRTG （压力）等级 RatingCL 等级 ClassSMLS 无缝 Seamless螺旋缝。
管道行业中英文词汇大全
管道行业中英文词汇大全1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbowk半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet) 异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet) 异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull head)45°斜三通45° lateral45°斜三通（支管为异径）45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run) 45°斜三通(一个直通口及支管为异径) 45° later al (reducing on one run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and outlet)异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run and both outlet) 异径管reducer 同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss管接头coupling, full coupling半管接头half coupling异径管接头reducing coupling活接头union内外螺纹缩接（俗称补芯）bushing管帽cap (C)堵头plug短节nipple异径短节reducing nipple; swage nipple1.3 弯管Bend预制弯管fabricated pipe bend跨越弯管（^ 形）cross-over bend偏置弯管（~ 形）offset bend90°弯管quarter bend环形弯管cirele bend单侧偏置90°弯管（? 形）single offset quarter bendS形弯管“S” bend单侧偏置U形膨胀弯管（| ?形）single offset “U” bendU形弯管“U” bend双偏置U膨胀弯管double offset expansion “U” bend斜接弯管mitre bend三节斜接弯管3-piece mitre bend折皱弯管corrugated bend圆度roundness1.4 法兰Flange (FLG）整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰（包括平焊法兰）slip-on flange (SO); slip-on welding flange承插焊法兰socket welding flange松套法兰lap joint flange (LJF)对焊法兰welding neckflange (WNF)法兰盖blind flange, blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange对焊环welding neck collar （与stub end相似）平焊环welding-on collar突缘短节stub end, lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating, pressure rating class压力—温度等级pressure-temperature rating法兰密封面，法兰面flange facing突面raised face (RF)凸面male face (MF)凹面female face (FMF)榫面tongue face槽面groove face环连接面ring joint face全平面；满平面flat face; full face (FF)光滑突面smooth raised face (SRF)法兰面加工facing finish粗糙度roughness光滑的smooth齿形serrated均方根root mean square (RMS)算术平均粗糙高度arithmetical average roughness height (AARH)配对法兰companion-flange螺栓圆bolt circle (B.C.)1.5 垫片Gasket (GSKT)垫片的型式type of gasket平垫片flat gasket环形平垫片flat ring gasket平金属垫片flat metal gasket夹棉织物的橡胶elastomer with cotton fabric insertion夹石棉织物的橡胶elastomer with asbestos fabric insertion夹石棉织物及金属丝加强的橡胶elastomer with asbestos fabric insertion and with wire reinforcement 无石墨压缩白石棉垫片non graphited compressed white asbestos gasket天然白橡胶垫片natural white rubber gasket压缩石棉垫片compressed asbestos class gasket浸聚四氟乙烯的石棉垫片PTFE impregnated asbestos gasket 夹石棉的缠绕金属垫片spiral-wound metal gasket with asbestos filler内环inner ring外环，外定位环outer ring波纹金属垫片corrugated metal gasket波纹金属包嵌石棉垫片corrugated metal gasket with asbestos inserted双夹套波纹金属包石棉垫片corrugated metal double jacketed asbestos filled gasket 双夹套垫片double jacketed gasket 金属包石棉平垫片flat metal jacketed asbestos filled gasket整体金属齿形垫片solid metal serrated gasket槽形金属垫片grooved metal gasket环形连接金属垫片ring joint metal gasket八角环形垫片octagonal ring gasket椭圆环形垫片oval ring gasket透镜式垫片lens gasket非金属垫片non-metallic gasket1.6 阀门Valve1.6.1 阀门结构、零件阀轭yoke外螺纹阀杆及阀轭outside screw and yoke (OS & Y)阀杆stem内螺纹inside screw (IS)阀轭套yoke sleeve阀杆环stem ring阀座valve seat (body seat)阀座环、密封圈seat ring整体（阀）座integral seat堆焊（阀）座deposited seat阀芯（包括密封圈、杆等内件）trim阀盘disc阀盘密封圈disc seat阀体body阀盖bonnet阀盖衬套bonnet bush螺纹阀帽screw cap螺纹阀盖screw bonnet螺栓连接的阀盖bolted bonnet (BB) 活接阀盖（帽）union bonnet (cap)螺栓连接的阀帽bolted cap (BC)焊接阀盖welded bonnet (WB)本体阀杆密封body stem seal石棉安全密封asbestos emenen seal 倒密封back seal压力密封的阀盖pressure-tight bonnet 动力操纵器powered operator电动操纵器electric motor operator 气动操纵器pneumatic operator液压操纵器hydraulic operator快速操纵器quick-acting operator滑动阀杆sliding stem正齿轮传动spur gear operated伞齿轮传动bevel gear operated扳手操作wrench operated链轮chain wheel手轮hand wheel手柄hand lever (handle)气缸（或液压缸）操纵的cylinder operated链条操纵的chain operated等径孔道full bore; full port异径孔道reducing bore, reduced port,venturi port 短型short pattern紧凑型（小型）compact type笼式环lantern ring压盖gland阀杆填料stem packing阀盖垫片bonnet gasket升杆式（明杆）rising stem (RS)非升杆式（暗杆）non-rising stem (NRS)指示器/限位器indicator/stopper注油器grease injector可更换的阀座环renewable seat ring1.6.2 常用阀(1）闸阀gate valve平行双闸板double disc parallel seat开口楔形闸板split wedge挠性整体楔形闸扳flexible solid wedge整体楔形闸板solid wedge塞型闸阀plug gate valve直通型闸阀through conduit gate valve(2) 截止阀globe valve球心型阀盘globe type disc塞型阀盘plug type disc可转动的阀盘swivel disc(3) 节流闪阀throttle valve针阀needle valve(4) 角阀angle valve(5) Y型阀（Y 型阀体截止阀）Y-valve (Y-body globe valve)(6) 球阀ball valve三通球阀3-way ball valve装有底轴的trunnion mounted耐火型fire safe type浮动球型floating ball type防脱出阀杆blowout proof stem(7) 蝶阀butterfly valve对夹式（薄片型）wafer type凸耳式lug type偏心阀板蝶阀offset disc burerfly valve; eccentric butterfly valve 斜阀盘蝶阀canted disc butterfly valve连杆式蝶阀link butterfly valve8) 柱塞阀piston type valve(9) 旋塞阀plug valve三通旋塞阀three-way plug valve四通旋塞阀four-way plug valve旋塞cock衬套旋塞sleeve cock(10) 隔膜阀diaphragm valve橡胶衬里隔膜阀rubber lined diaphragm valve直通式隔膜阀straight way diaphragm valve堰式隔膜阀weir diaphragm valve(11) 夹紧式胶管阀pinch valve（用于泥浆、粉尘等）(12) 止回阀check valve升降式止回阀lift check valve旋启式止回阀swing check valve, flap check valve落球式止回阀ball check valve弹簧球式止回阀spring ball check valve双板对夹式止回阀dual plate wafer type check valve无撞击声止回阀non-slam cheek valve底阀foot valve切断式止回阀stop check valve; non-return valve活塞式止回阀piston check valve斜翻盘止回阀tilting disc check valve蝶式止回阀butterfly check valve1.6.3 其它用途的阀安全泄气阀safety valve (SV)安全泄液阀relief valve (RV)安全泄压阀safety relief valve杠杆重锤式lever and weight type引导阀操纵的安全泄气阀pilot operated safety valve复式安全泄气阀twin type safety valve罐底排污阀flush-bottom tank valve电磁阀solenoid valve, solenoid operated valve电动阀electrically operated valve, electric-motor operated valve气动阀pneumatic operated valve低温用阀cryogenic service valve蒸汽疏水阀steam trap机械式疏水阎mechanical trap浮桶式疏水阀open bucket trap, open top bucket trap浮球式疏水阀float trap倒吊桶式疏水阀inverted bucket trap自由浮球式疏水阀loose float trap恒温式疏水阀thermostatic trap金属膨胀式蒸汽疏水阀metal expansion steam trap液体膨胀式蒸汽疏水阀liquid expansion steam trap双金属膨胀式蒸汽疏水阀bimetallic expansion steam trap压力平衡式恒温疏水阀balanced pressure thermostatic trap热动力式疏水阀thermodynamic trap脉冲式蒸汽疏水阀impulse steam trap放气阀（自动放气阀）air vent valve (automatic air vent valve) （疏水阀用）平板式滑动闸阀slab type sliding gate valve盖阀flat valve换向阀diverting valve, reversing valve热膨胀阀thermo expansion valve自动关闭阀self-closing gate valve自动排液阀self-draining valve管道盲板阀line-blind valve挤压阀squeeze valve（用于泥浆及粉尘等）呼吸阀breather valve风门、挡板damper减压阀pressure reducing valve, reducing valve控制阀control valve膜式控制阀diaphragm operated control valve执行机构actuator背压调节阀back pressure regulating valve差压调节阀differential pressure regulating valve压力比例调节阀pressure ratio regulating valve1.6.4 未指明结构（或阀型）的阀切断阀block valve; shut-off valve; stop valve调节阀regulating valve快开阀quick opening valve快闭阀quick closing valve隔断阀isolating valve三通阀three way valve夹套阔jacketed valve非旋转式阀non-rotary valve排污阀blowdown valve集液排放阀drip valve排液阀drain valve放空阀vent valve卸载阀unloading valve排出阀discharge valve吸入阀suction valve多通路阀multiport valve取样阀sampling valve手动阀hand-operated valve; manually operated valve 锻造阀forged valve铸造阀cast valve（水）龙头bibb; bib; faucet抽出液阀（小阀）bleed valve旁路阀by-pass valve软管阀hose valve混合阀mixing valve破真空阀vacuum breaker冲洗阀flush valve第一道阀；根部阀primary valve根部阀root valve总管阀header valve事故切断阀emergency valve1.7 管道特殊件Piping Specialty1.7.1 管道特殊件（组件）粗滤器strainer过滤器filter临时粗滤器（锥型）temporary strainer (cone type)y 型粗滤器y-type strainerT型粗滤器T-type strainer永久过滤器permanent filter丝网粗滤器gauze strainer洗眼器及淋浴器eye washer and shower视镜sight glass阻火器flame arrester喷嘴；喷头spray nozzle取样冷却器sample cooler消声器silencer膨胀节expansion joint波纹膨胀节bellow expansion joint单波single bellow双波double bellow多波multiple bellow压力平衡式膨胀节pressure balanced expansion带铰链膨胀节hinged expansion joint轴向位移型膨胀节axial movement type expansion joint 自均衡膨胀节（外加强环）self-equalizing expansion joint 带接杆膨胀节tied expansion joint万向型膨胀节universal type expansion joint球形补偿器ball type expansion joint填函式补偿器slip type (packed type) expansion joint单向滑动填料函补偿器single actionpacked slip joint1.7.2 管道特殊元件Piping Special Element软管接头hose connection (HC)快速接头quick coupling金属软管metal hose橡胶管rubber hose挠性管flexible tube鞍形补强板reinforcing saddles补强板reinforcement pad特殊法兰special flange漏斗funnel排液环drip ring排液漏斗drain funnel插板blank垫环spacer8字盲板spectacle blind; figure 8 blind限流孔板restriction orifice爆破片rupture disk法兰盖贴面protective disc费托立克接头victaulic coupling1.8 端部连接End Connection法兰端flanged end坡口端beveled end (BE)对焊端butt welded end平端plain end (PE)承插焊端socket welding end螺纹端threaded end (TE)承口bell end焊接端welding end法兰连接（接头）flanged joint对焊连接（接头）butt welded joint螺纹连接，管螺纹连接threaded joint, pipe threaded joint 锥管螺纹密封焊连接seal-welded taper pipe threaded joint 承插焊连接（接头）socket welded joint承插连接（接头）bell and spigot joint环垫接头ring joint (RJ)万向接头universal joint软钎焊连接（接头）soldered joint搭接接头，松套连接lapped joint外侧厚度切斜角bevel for outside thickncss内侧厚度切斜角bevel for inside thickness内外侧厚度切斜角bevel for combined thickness法兰式的flanged (FLGD)对焊的butt welded (BW)螺纹的threaded (THD)承插焊的socket welded (SW)小端为平的small end plain (SEP)大端为平的large end plain (LEP)两端平both ends plain (BEP)小端带螺纹small end thread (SET)大端带螺纹large end thread (LET)两端带螺纹both end thread (BET)一端带螺纹one end thread (OET)支管连接branch connection焊接支管branch pipe welded directly to the run pipe2 管道用紧固件及螺纹2.1 紧固件螺栓bolt六角头螺栓hexagonal head bolt方头螺栓square head bolt螺柱，双头螺栓stud bolt环头螺检eye bolt沉头螺栓countersunk (head) screw地脚螺栓anchor bolt; foundation bolt 松紧螺旋扣（花篮螺丝）turnbuckleU形螺栓U-boltT形螺栓T-bolt圆头螺钉round head bolt机螺栓，机螺钉maehine bolt顶开螺栓，顶起螺栓Jack screw自攻螺钉self tapping screw膨胀螺栓expansion bolt粗制的coarse精制的finished, fine螺母nut六角螺母hexagonal nut方螺母square nut蝶形螺母wing nut扁螺母flat nut锁紧螺母lock nut垫圈washer平垫圈plain washer球面垫圈spherical washer弹簧垫圈spring washer方垫圈square washer斜垫圈slant washer销轴pinned shan销pin开口销cotter pin定位销dowel pin带孔销pin with hole圆锥销taper pin铆钉rivet键key2.2 螺纹左螺纹left hand thread右螺纹right hand thread管螺纹pipe thread锥管螺纹taper pipe thread直管螺纹straight pipe thread梯形螺纹trapezoid thread螺距pitch of thread粗牙螺纹coarse thread细牙螺纹fine thread特细牙螺纹extra fine thread通长螺纹full thread惠氏螺纹whitworth thread公制螺纹metric ibread美国标准锥管螺纹American standard taper pipe thread (NPT) 螺孔tap3 材料、型钢及填料3.1 金属材料3.1.1 黑色金属Ferrous Metal碳素钢carbon steel (CS)低碳钢low-carbon steel中碳钢medium-carbon steel高碳钢high-carbon steel普通碳素钢general carbon steel优质碳素钢high-quality carbon steel普通低合金结构钢general structure low-alloy steel 合金结构钢structural alloy steel合金钢alloy steel低合金钢low alloy steel中合金钢medium alloy steel高合金钢high alloy steel耐热钢heat resisting steel高强度钢high strength steel复合钢clad steel工具钢tool steel弹簧钢spring steel钼钢molybdenum steel镍钢nickel steel铬钢chromium steel铬钼钢chrome-molybdenum steel铬镍钢chromium-nickel steel,chrome-nickel steel 不锈钢stainless steel (S.S.)奥氏体不锈钢Austenitic stainless steel马氏体不锈钢Martensitic stainless steel司特来合金（钨铬钴台金）Stellite耐蚀耐热镍基合金Hastelloy铬镍铁合金inconel耐热铬镍铁合金incoloy20合金20 alloy平炉钢（马丁钢）Martin steel镇静钢killed steel半镇静钢semi-killed steel沸腾钢rimmed steel; rimming steel; open-steel 锻钢forged steel铸钢cast steel铸铁cast iron (C.I.)灰铸铁grey cast iron可锻铸铁malleable iron (MI)球墨铸铁nodular cast iron; nodular graphite iron 生铁pig iron熟铁，锻铁wrought iron铸件casting高硅铸铁high silicon cast iron3.1.2 镀层及制造方法渗铬钢，镀铬钢chromized steel镀铬的chromium-plated, chrome-plated 镀层plating锻造，型钢swage锻造的，锻造forging轧制rolling热轧hot rolling冷轧cold rolling挤压extruding冷加工cold working热加工hot working拔制drawing3.1.3 有色金属Non-ferrous Metal铝aluminum铜，紫铜copper黄铜brass青铜bronze铝青铜aluminum bronze磷青铜phosphor bronze铝镁合金aluminum magnesium锰青铜manganese bronze蒙乃尔（注：镍及铜合金）Monel镍铜台金nickel copper alloy非铁合金nonferrous alloy钛titanium铅lead硬铅hard lead3.1.4 材料性能极限强度ultimate strength抗拉强度tensile strength屈服极限yield limit屈服点yield point延伸率percentage elongation抗压强度compressive strength抗弯强度bending strength弹性极限elastic limit冲击值impact value疲劳极限fatigue limit蠕变极限creep limit持久极限endurance limit布氏硬度Brinell hardness洛氏硬度Rockwell hardness维氏硬度Vickers diamond hardness, diamond penetrator hardness 蠕变断裂强度creep rupture strength断面收缩率reduction of area韧性toughess脆性brittleness延性ductility冷脆cold shortness冷流cold flow3.2 非金属材料Non-metallic Material塑料plastic丙烯腈—丁二烯—苯乙烯acrylonitrile-butadiene-styrene (ABS) 聚乙烯polyethylene (PE)聚氯乙烯polyvinyl chloride (PVC)苯乙烯橡胶styrene-rubber (SR)聚丁烯polybutylene (PB)聚丙烯polypropylene (PP)聚苯乙烯polystyrene (PS)氯化聚醚chlorinated polyether (CPE)聚酰胺polyamide (PA)聚碳酸酯polycarbonate (PC)聚甲基丙烯酸甲酯polymethyl methacrylate (PMMA)醋酸丁酸纤维素cellulose acetate butyrate (CAB)氯化聚氯乙烯chlorinated polyvinyl chloride (CPVC)聚偏二氟乙烯polyvinylidene fluoride (PVDF)缩醛塑料acetal plastic尼龙塑料nylon plastic聚烯烃polyolefin (PO)石墨酚醛塑料graphite phenolic plastics聚四氟乙烯polytetrafluoroethylene (PTFE)纤维增强热塑性塑料fiber reinforced thermoplastics热塑性塑料thermoplastic热固性塑料thermosetting plastics胶粘剂adhesive溶剂胶接剂solvent cement树脂resin环氧树脂epoxy, epoxy resin聚酯树脂polyester resin聚酯纤维polyester fibers氟塑料fluoroplastics聚氨基甲酸酯polyurethane丙烯酸树脂acrylic resin脲醛树脂urea resin呋哺树脂furan resin乙烯丙烯二烃单体ethylene propylene diene monomer (EPDM)合成橡胶synthetic rubber橡胶rubber丁腈橡胶nitrile butadiene rubber氯丁橡胶neoprene天然橡胶natural rubber乙丙橡胶ethylene propylene rubber (EPR) 玻璃glass硼硅玻璃borosilicate glass耐火砖fire brick陶瓷ceramic搪瓷porcelain enamel木材wood3.3 型材型钢shaped steel, section steel, swage角钢angle steel槽钢channel工字钢I-beam宽缘工字钢或H钢wide flanged beamT型钢T-bar方钢square bar扁钢flat bar角钢hexagonal steel bar圆钢round steel; rod钢带strap steel钢板plate网纹钢板checkered plate腹板（指型钢的立板）web翼缘（指型钢的缘）wing3.4 填料及填料函填料packing石棉绳asbestos rope, asbestos cord．O形环O-ring自密封self-sealing四氟带T eflon tap带铬镍合金丝的石棉绳asbestos rope with inconel wire, inconel wire asbestos 浸聚四氟乙烯的石棉填料Teflon impregnated asbestos packing金属填料metallic stuffing填料箱，填料函packing box, stuffing box填料函压盖stuffing box gland4 管道等级及材料统计4.1 管道材料规定Piping Material Specification管道等级piping class; piping classification管道等级号class designation公称直径nominal diameter (DN); nominal (pipe) size公称压力nominal pressure (PN)压力级，等级，类别class (CL)低压low pressure (L.P.)中压medium pressure (M.P.)高压high pressure (H.P.)大气压atmosphere (ATM)真空vacuum工作压力operating pressure; working pressure设计压力design pressure工作温度operating temperature设计温度design temperature环境温度ambient temperature腐蚀裕量corrosion allowance管道附件piping attachment管道元件piping element壁厚wall thickness (WT)壁厚系列号schedule number (SCH. No.)加厚的，加强的extra heavy, extra strong双倍加厚的，双倍加强的double extra heavy, double extra strong通用连接组typieal installation分组（类）形式（如管道等级表）block form数据库data base文件file4.2 材料统计Material T ake-off (MTO)汇总表summary sheet材料表bill of material (BM)综合管道材料表consolidated piping material summary sheet (CPMSS)统计材料准确度accuracy of take-off材料情况报告material status report (MSR) 散装材料bulk material编位号的itemized代码code number短代码short code数量quantity (QTY)重力weight净重net weight毛重gross weight再生塔regenering tower造粒塔prflling tower汽提塔stripper脱气塔degasifier合成塔synthesis tower(2) 反应器reactor聚台釜polymerizer转化器，变换器converter脱硫反应器desulphurization reactor 甲烷化器methanator(3) 气柜gas-holder螺旋式气柜helical gas-holder湿式气柜wet gas-holder干式气柜dry gas-holder(4) 槽罐贮罐tank; storage tank缓冲罐knock out drum球罐spheroid, spherical tank罐drum接受槽receiver计量槽measuring tank加料槽feed tank排污罐blow down tank闪蒸罐flash drum汽包steam drum溶液贮槽solution storage tank地下槽sloptank(5) 其它设备分离器separator旋风分离器cyclone分子筛molecular sieve脱氧器deaerator搅拌器agitator干燥器dryer混合器mixer萃取器extractor结晶器crystallizer澄清器gravity settler净化器purifier气化器vaporizer吸附器adsorber融解槽melter减温器desuperheater升压器booster喷射器ejector喷头sprayer火炬flare消声器silencer(6) 换热器、加热器、冷却器换热器heat exchanger空冷器air cooler水冷却器water cooler冷凝器condenser螺旋板式换热器spiral plate heat exchanger 蒸发器evaporator 再沸器reboiler急冷器quencher深冷器chiller预热器preheater再热器reheater加热器heater电加热器electric heater过热器super heater给水加热器feed water heater中间冷却器inter cooler后冷却器after cooler5.1.2 工业炉及锅炉炉子furnace烧嘴burner锅炉boiler烟囱stack废热锅炉waste heat boiler辅助锅炉auxiliary boiler省煤器economizer回热炉direct-fired heater辐射段radiant section对流段convection section裂化炉reformer焚烧炉incinerator回转窑rotary kiln炉管furnace tube吹灰器soot blower观察孔observation door, peep door防爆门explosion door5.2 辅助用房名称5.2.1 生产用房分析室analyzer room变压器室transformer room配电室，变电所substation, switch room 蓄电池室battery room控制室control room通风室ventilating room贮藏室storage room维修间maintenance room办公室office5.2.2 生活用房更农室locker room盥洗室，厕所closet, lavatory, toilet5.3 图名管道布置平面piping arrangement plan (PAP)管道布置piping layout轴测图isometric drawing分区索引图key plan初版设备布置图（―A‖版）preliminary plot plan ( ―A‖ issue)内部审查版设备布置图（―B‖版）inrernal a pproval plot plan ( ―B‖ issue)用户审查版设备布置图（―C‖版) owner approval plot plan ( ―C‖ issue)确认版设备布置图（―D‖版）confirm plot plan ( ―D‖ issue)研究版设备布置图（―e‖版）planning plot plan ( ―E‖ issue)设计版设备布置图（―F‖）designing plot plan ( ―F‖ issue)施工版设备布置图（―G‖版）construction pl ot plan ( ―G‖ issue)5.4 厂房、站、单元压缩机房compressor house (room)泵房pump house (room)洗眼站eye washer station泡沫站foam station软管站，公用工程站hose station (HS), utility station成套设备package unit设施facilities罐区tank yard空分装置air separation facility5.5 设备布置设备位号equipment item number工厂plant工厂区界plant limit项目区界内侧inside battery limit (I.S.B.L.)项目区界batterylimit (BL)区界area limit区域边界zone iimit界外off site东east (E)西west (W)南south (S)北north (N)上up下down工厂北向plant north真实北向true north道路road小过道cat walk, cat way走道，过道walk way, gangway, access way 污水坑（井）sump pit集水池catch basin沟槽through预留区trough场地future area铺砌区paving area非铺砌区unpaved area碎石铺面gravel paving橡皮铺面rubber paving面积，区域area体积，容积volume (VOL)5.6 管道布置管道设计piping design管道研究piping study走向研究routing study重要管道critical piping地上管道above ground piping地下管道under ground piping管网network of pipes管廊pipe rack管沟piping trench管间距line spacing管道跨距line span总管header, manifold旁路by pass排液drain放空vent上升管，垂直管riser导管canduit裸管bare iine管件直接fitting to fitting (FTF)管段，接口spool piece, spool取样接口sampling connection集液包drip leg伴热管tracing pipe蒸汽伴热steam tracing热水伴热hot-water tracing电伴热electrical tracing夹套管jacketed line, jacketed piping 全夹套的full jacketed平面plan详图detail― ‖视图X view ―X‖― ‖剖视A-A section ―A-A‖连接图hook up drawing接续图continue on drawing (COD)接续线match line (M.L.)比例scale图例legend符号symbol管口表list of nozzles方位orientation管口方位nozzle orientation定位location相交intersection水平的horizontal垂直的，立式的vertical垂直，正交，垂直的perpendicular平行，平行的parallel水平安装horizontal installation垂直安装vertical installafion对称的symmetric相反（的），对面（的）opposite顺时针方向clock wise逆时针方向counter clock wise计算机辅助设计computer aided design (CAD) 5.7 图面标注绝对标高abselute elevation海平面标高over-sea mean level (OSL)标高，立面elevation (EL)混凝土顶面top of concrete架顶面top of support (TOS)钢结构顶面top of steel梁项面top of beam (TOB)支撑点point of suppon (POS)管顶top of pipe (TOP)管底bouom of pipe (BOP)沟底boaom of trench管子内底invert (inside bottom of pipe) 底平flat on bottom (FOB)顶平flat on top (FOT)工作点working point (W.P.)面至面face to face (F-F)中心至端面center to end (C-E)中心至面center to face (C-F)中心至中心，中至中center to center (C-C) 坐标coordinate坐标原点origin of coordinate出口中心线center line of discharge入口中心线center line of suction中心线centerline (CL)入口inlet, suction出口outlet, discharge排出口exhaust距离distance。
管道及管件常用词汇
管道及管件常用词汇以下是管道及管件常用词汇：1. 管道（Pipe）2. 管件（Fitting）3. 弯头（Elbow）4. 管道接头（Pipe joint）5. 管道法兰连接（Flanged connection）6. 焊接连接（Welded connection）7. 螺纹连接（Threaded connection）8. 肩型连接（Shoulder connection）9. 快速接头（Quick coupling）10. 管道套筒（Pipe sleeve）11. 管道补偿器（Pipe compensator）112. 管道支架（Pipe hanger）13. 管道支撑（Pipe support）14. 管道附件（Pipe accessory）15. 管道密封（Pipe sealing）16. 管道阀门（Pipe valve）17. 膨胀节（Expansion joint）18. 排气阀（Air vent valve）19. 抽水阀（Drain valve）20. 截止阀（Stop valve）21. 调节阀（Control valve）22. 安全阀（Safety valve）23. 蝶阀（Butterfly valve）24. 球阀（Ball valve）25. 压力表（Pressure gauge）226. 温度计（Thermometer）27. 流量计（Flow meter）28. 规格（Specification）29. 材质（Material）30. 内径（Inner diameter）31. 外径（Outer diameter）32. 壁厚（Wall thickness）33. 长度（Length）34. 压力等级（Pressure rating）35. 温度等级（Temperature rating）36. 标准（Standard）37. 法兰（Flange）38. 异径（Reducer）39. 等径（Equal tee）340. 止回阀（Check valve）4。
管道专业术语常用英语单词
title
drawn No.
scale
temperature
design temperature
humidity
flow
flow velocity
centigrade scale(℃)
Fahrenheit scale(°F)
nominal diameter(DN)
steam pipe
condensate pipe
cooling water pipe
溢流管
循环管
放水管
煤气管
压缩空气管
液化石油气管
氧气管
乙炔管
真空管
地下管道
顶管
埋深
管沟
管道工
安装
安装工程
组装
热水采暖
蒸汽采暖
自动消防系统
喷水灭火系统
埋设、暗敷
总管
立管
横管
水平管
支管
向上去
向下去
坐标
绝对标高
相对标高
坡度
automatic fire system
sprinker system
built-in
main pipe
stack；riser
horizontal
horizontal
branch pipe
to above(T/A)
to below(T/B)
coordinates
absolute elevation；absolute level
管道专业术语常用英语单词
在引进装置、涉外及中外合资技术改造工程的技术资料中，经常要接触到英语单词。由于管道安装涉及多项工程技术，而不从属于任何一项工程技术分支，故其技术性质有一定特殊性，不少英语词汇是在实践中逐渐形成的，借助一般科技英汉词典有时也难以找到它们的确切含意。现将管道安装工程中出现较多的单词整理列出，如果能熟悉这些单词，对阅英文图纸能收到事半功倍的效果。
管道常用的英文单词
绝好的网址（下面没有粘贴完）/bbs/read.php?tid=55411 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe 螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbowk半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet)异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet)异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull head) 45°斜三通45° lateral45°斜三通（支管为异径）45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run)45°斜三通(一个直通口及支管为异径) 45° lateral (reducing on one run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and outlet)异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run and both outlet)异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss管接头coupling, full coupling半管接头half coupling异径管接头reducing coupling活接头union内外螺纹缩接（俗称补芯）bushing管帽cap (C)堵头plug短节nipple异径短节reducing nipple; swage nipple1.3 弯管Bend预制弯管fabricated pipe bend跨越弯管（^ 形）cross-over bend偏置弯管（~ 形）offset bend90°弯管quarter bend环形弯管cirele bend单侧偏置90°弯管（? 形）single offset quarter bendS形弯管“S” bend单侧偏置U形膨胀弯管（| ?形）single offset “U” bendU形弯管“U” bend双偏置U膨胀弯管double offset expansion “U” bend斜接弯管mitre bend三节斜接弯管3-piece mitre bend折皱弯管corrugated bend圆度roundness1.4 法兰Flange (FLG）整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰（包括平焊法兰）slip-on flange (SO); slip-on welding flange 承插焊法兰socket welding flange松套法兰lap joint flange (LJF)对焊法兰welding neckflange (WNF)法兰盖blind flange, blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange对焊环welding neck collar （与stub end相似）平焊环welding-on collar突缘短节stub end, lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating, pressure rating class压力—温度等级pressure-temperature rating法兰密封面，法兰面flange facing突面raised face (RF)凸面male face (MF)凹面female face (FMF)榫面tongue face槽面groove face环连接面ring joint face全平面；满平面flat face; full face (FF)光滑突面smooth raised face (SRF)法兰面加工facing finish粗糙度roughness光滑的smooth齿形serrated均方根root mean square (RMS)算术平均粗糙高度arithmetical average roughness height (AARH)配对法兰companion-flange螺栓圆bolt circle (B.C.)1.5 垫片Gasket (GSKT)垫片的型式type of gasket平垫片flat gasket环形平垫片flat ring gasket平金属垫片flat metal gasket夹棉织物的橡胶elastomer with cotton fabric insertion夹石棉织物的橡胶elastomer with asbestos fabric insertion夹石棉织物及金属丝加强的橡胶elastomer with asbestos fabric insertion and with wire reinforcement无石墨压缩白石棉垫片non graphited compressed white asbestos gasket天然白橡胶垫片natural white rubber gasket压缩石棉垫片compressed asbestos class gasket浸聚四氟乙烯的石棉垫片PTFE impregnated asbestos gasket夹石棉的缠绕金属垫片spiral-wound metal gasket with asbestos filler内环inner ring外环，外定位环outer ring波纹金属垫片corrugated metal gasket波纹金属包嵌石棉垫片corrugated metal gasket with asbestos inserted双夹套波纹金属包石棉垫片corrugated metal double jacketed asbestos filled gasket 双夹套垫片double jacketed gasket金属包石棉平垫片flat metal jacketed asbestos filled gasket整体金属齿形垫片solid metal serrated gasket槽形金属垫片grooved metal gasket环形连接金属垫片ring joint metal gasket八角环形垫片octagonal ring gasket椭圆环形垫片oval ring gasket透镜式垫片lens gasket非金属垫片non-metallic gasket1.6 阀门Valve1.6.1 阀门结构、零件阀轭yoke外螺纹阀杆及阀轭outside screw and yoke (OS & Y) 阀杆stem内螺纹inside screw (IS)阀轭套yoke sleeve阀杆环stem ring阀座valve seat (body seat)阀座环、密封圈seat ring整体（阀）座integral seat堆焊（阀）座deposited seat阀芯（包括密封圈、杆等内件）trim阀盘disc阀盘密封圈disc seat阀体body阀盖bonnet阀盖衬套bonnet bush螺纹阀帽screw cap螺纹阀盖screw bonnet螺栓连接的阀盖bolted bonnet (BB)活接阀盖（帽）union bonnet (cap)螺栓连接的阀帽bolted cap (BC)焊接阀盖welded bonnet (WB)本体阀杆密封body stem seal石棉安全密封asbestos emenen seal倒密封back seal压力密封的阀盖pressure-tight bonnet动力操纵器powered operator电动操纵器electric motor operator气动操纵器pneumatic operator液压操纵器hydraulic operator快速操纵器quick-acting operator滑动阀杆sliding stem正齿轮传动spur gear operated伞齿轮传动bevel gear operated扳手操作wrench operated链轮chain wheel手轮hand wheel手柄hand lever (handle)气缸（或液压缸）操纵的cylinder operated链条操纵的chain operated等径孔道full bore; full port异径孔道reducing bore, reduced port,venturi port短型short pattern紧凑型（小型）compact type笼式环lantern ring压盖gland阀杆填料stem packing阀盖垫片bonnet gasket升杆式（明杆）rising stem (RS)非升杆式（暗杆）non-rising stem (NRS)指示器/限位器indicator/stopper注油器grease injector可更换的阀座环renewable seat ring1.6.2 常用阀(1）闸阀gate valve平行双闸板double disc parallel seat开口楔形闸板split wedge挠性整体楔形闸扳flexible solid wedge整体楔形闸板solid wedge塞型闸阀plug gate valve直通型闸阀through conduit gate valve(2) 截止阀globe valve球心型阀盘globe type disc塞型阀盘plug type disc可转动的阀盘swivel disc(3) 节流闪阀throttle valve针阀needle valve(4) 角阀angle valve(5) Y型阀（Y 型阀体截止阀）Y-valve (Y-body globe valve)(6) 球阀ball valve三通球阀3-way ball valve装有底轴的trunnion mounted耐火型fire safe type浮动球型floating ball type防脱出阀杆blowout proof stem(7) 蝶阀butterfly valve对夹式（薄片型）wafer type凸耳式lug type偏心阀板蝶阀offset disc burerfly valve; eccentric butterfly valve 斜阀盘蝶阀canted disc butterfly valve连杆式蝶阀link butterfly valve8) 柱塞阀piston type valve(9) 旋塞阀plug valve三通旋塞阀three-way plug valve四通旋塞阀four-way plug valve旋塞cock衬套旋塞sleeve cock(10) 隔膜阀diaphragm valve橡胶衬里隔膜阀rubber lined diaphragm valve直通式隔膜阀straight way diaphragm valve堰式隔膜阀weir diaphragm valve(11) 夹紧式胶管阀pinch valve（用于泥浆、粉尘等）(12) 止回阀check valve升降式止回阀lift check valve旋启式止回阀swing check valve, flap check valve落球式止回阀ball check valve弹簧球式止回阀spring ball check valve双板对夹式止回阀dual plate wafer type check valve无撞击声止回阀non-slam cheek valve底阀foot valve切断式止回阀stop check valve; non-return valve活塞式止回阀piston check valve斜翻盘止回阀tilting disc check valve蝶式止回阀butterfly check valve1.6.3 其它用途的阀安全泄气阀safety valve (SV)安全泄液阀relief valve (RV)安全泄压阀safety relief valve杠杆重锤式lever and weight type引导阀操纵的安全泄气阀pilot operated safety valve复式安全泄气阀twin type safety valve罐底排污阀flush-bottom tank valve电磁阀solenoid valve, solenoid operated valve电动阀electrically operated valve, electric-motor operated valve 气动阀pneumatic operated valve低温用阀cryogenic service valve蒸汽疏水阀steam trap机械式疏水阎mechanical trap浮桶式疏水阀open bucket trap, open top bucket trap浮球式疏水阀float trap倒吊桶式疏水阀inverted bucket trap自由浮球式疏水阀loose float trap恒温式疏水阀thermostatic trap金属膨胀式蒸汽疏水阀metal expansion steam trap液体膨胀式蒸汽疏水阀liquid expansion steam trap双金属膨胀式蒸汽疏水阀bimetallic expansion steam trap压力平衡式恒温疏水阀balanced pressure thermostatic trap热动力式疏水阀thermodynamic trap脉冲式蒸汽疏水阀impulse steam trap放气阀（自动放气阀）air vent valve (automatic air vent valve) （疏水阀用）平板式滑动闸阀slab type sliding gate valve盖阀flat valve换向阀diverting valve, reversing valve热膨胀阀thermo expansion valve自动关闭阀self-closing gate valve自动排液阀self-draining valve管道盲板阀line-blind valve挤压阀squeeze valve（用于泥浆及粉尘等）呼吸阀breather valve风门、挡板damper减压阀pressure reducing valve, reducing valve控制阀control valve膜式控制阀diaphragm operated control valve执行机构actuator背压调节阀back pressure regulating valve差压调节阀differential pressure regulating valve压力比例调节阀pressure ratio regulating valve1.6.4 未指明结构（或阀型）的阀切断阀block valve; shut-off valve; stop valve调节阀regulating valve快开阀quick opening valve快闭阀quick closing valve隔断阀isolating valve三通阀three way valve夹套阔jacketed valve非旋转式阀non-rotary valve排污阀blowdown valve集液排放阀drip valve排液阀drain valve放空阀vent valve卸载阀unloading valve排出阀discharge valve吸入阀suction valve多通路阀multiport valve取样阀sampling valve手动阀hand-operated valve; manually operated valve锻造阀forged valve铸造阀cast valve（水）龙头bibb; bib; faucet抽出液阀（小阀）bleed valve旁路阀by-pass valve软管阀hose valve混合阀mixing valve破真空阀vacuum breaker冲洗阀flush valve第一道阀；根部阀primary valve根部阀root valve总管阀header valve事故切断阀emergency valve1.7 管道特殊件Piping Specialty1.7.1 管道特殊件（组件）粗滤器strainer过滤器filter临时粗滤器（锥型）temporary strainer (cone type)y 型粗滤器y-type strainerT型粗滤器T-type strainer永久过滤器permanent filter丝网粗滤器gauze strainer洗眼器及淋浴器eye washer and shower视镜sight glass阻火器flame arrester喷嘴；喷头spray nozzle取样冷却器sample cooler消声器silencer膨胀节expansion joint波纹膨胀节bellow expansion joint单波single bellow双波double bellow多波multiple bellow压力平衡式膨胀节pressure balanced expansion带铰链膨胀节hinged expansion joint轴向位移型膨胀节axial movement type expansion joint 自均衡膨胀节（外加强环）self-equalizing expansion joint 带接杆膨胀节tied expansion joint万向型膨胀节universal type expansion joint球形补偿器ball type expansion joint填函式补偿器slip type (packed type) expansion joint单向滑动填料函补偿器single actionpacked slip joint1.7.2 管道特殊元件Piping Special Element软管接头hose connection (HC)快速接头quick coupling金属软管metal hose橡胶管rubber hose挠性管flexible tube鞍形补强板reinforcing saddles补强板reinforcement pad特殊法兰special flange漏斗funnel排液环drip ring排液漏斗drain funnel插板blank垫环spacer8字盲板spectacle blind; figure 8 blind限流孔板restriction orifice爆破片rupture disk法兰盖贴面protective disc费托立克接头victaulic coupling1.8 端部连接End Connection法兰端flanged end坡口端beveled end (BE)对焊端butt welded end平端plain end (PE)承插焊端socket welding end螺纹端threaded end (TE)承口bell end焊接端welding end法兰连接（接头）flanged joint对焊连接（接头）butt welded joint螺纹连接，管螺纹连接threaded joint, pipe threaded joint 锥管螺纹密封焊连接seal-welded taper pipe threaded joint 承插焊连接（接头）socket welded joint承插连接（接头）bell and spigot joint环垫接头ring joint (RJ)万向接头universal joint软钎焊连接（接头）soldered joint搭接接头，松套连接lapped joint外侧厚度切斜角bevel for outside thickncss内侧厚度切斜角bevel for inside thickness内外侧厚度切斜角bevel for combined thickness法兰式的flanged (FLGD)对焊的butt welded (BW)螺纹的threaded (THD)承插焊的socket welded (SW)小端为平的small end plain (SEP)大端为平的large end plain (LEP)两端平both ends plain (BEP)小端带螺纹small end thread (SET)大端带螺纹large end thread (LET)两端带螺纹both end thread (BET)一端带螺纹one end thread (OET)支管连接branch connection焊接支管 branch pipe welded directly to the run pipe。
管道工程英文术语缩写
管道工程英文术语缩写管道工程英文术语缩写标准化文件发布号：（9312-EUATWW-MWUB-WUNN-INNUL-DDQTY-KII管道工程英文术语缩写（中英对照）1.管子及管件P 管子 PipeEL 弯头ELL 长半径弯头ELS 短半径弯头MEL 斜接弯头（虾米腰弯头）REL 异径弯头T 三通 TeeLT 斜三通RT 异径三通R 异径管接头（大小头） ReducerCR 同心异径管接头（同心大小头） Concentric reducerER 偏心异径管接头（偏心大小头） Eccentric reducerCPL 管箍 CouplingFCPL 双头管箍 Full couplingHCPL 单头管箍 Half couplingRCPL 异径管箍 Reducing couplingBU 内外螺纹接头 BushingUN 活接头 UnionHC 软管接头 Hose couplerSE 翻边短节 Stub endNIP 短节 Pipe nipple or straight nippleSNIP 异径短节 Swaged nippleCP 管帽（封头） CapPL 管堵（丝堵） PlugBLK 盲板 BlankSB 8字盲板 Spectacle blind (blank)RP 补强板 Reinforcing pad2.法兰 FLG 法兰 FlangeWNF 对焊法兰 Welding neck flangeSOF 平焊法兰 Slip-on flangeSWF 承插焊法兰 Socket-welding flangeT 螺纹法兰 Threaded flangeLJ 松套法兰 Lapped joint flangeREDF 异径法兰 Reducing flangeBF 法兰盖（日法兰） Blind flangeFSF 法兰密封面 Flange scaling FF 全平面 Flat face RF 凸台面Raised faceMFF 凹凸面 Male and female faceLF 凹面 Female faceLM 凸面 Male faceRJ 环连接面 Ring joint faceTG 榫槽面 T ongue and groove faceTF 榫面 T ongue faceGF 槽面 Groove face3.垫片 G 垫片 GasketNMG 非金属垫片 Non-metallic gasketAG 石棉垫片 Asbestos gasketRG 橡胶垫片 Rubber gasketTEG 聚四氟乙烯包复垫片 PTFE envelope gasket SMG 半金属垫片 Semimetallic gasketMJG 金属包垫片 Meta-jacket gasketSWG 缠绕式垫片 Spiral wound gasketMG 金属垫片 Metallic gasketFMG 金属平垫片 Flat metallic gasketSMSG 齿形金属垫片 Solid metal serrated gasket LER 透镜式金属环垫 Lens ring gasketOCR 八角形金属环垫 Octagonal ring gasketOVR 椭圆形金属环垫 Oval ring gaksetIR/OR 内外定位环 Inner ring and outer ringIR 内定位环 Inner ringOR 外定位环 Outer ring4.坚固件 B 螺栓 BoltSB 螺柱 Stud boltNU 螺母 NutTB 花蓝螺母 TurnbuckleWSR 垫圈 WasherSWSR 弹簧垫圈 Spring washer5.阀门 GV 闸阀 Gate valveGLV 截止阀 Globe valveCHV 止回阀 Check valveBUV 蝶阀 Butterfly valveBAV 球阀 Ball valvePV 旋塞阀 Plug valve (cock)CV 调节阀 Control valveSV 安全阀 Safety valveRV 减压阀 Pressure reducing valveST 蒸汽疏水阀 Steam trapPRV 泄压阀 Pressur relief valveBV 呼吸阀 Breather valveNV 针形阀 Needle valveAV 角阀DV 隔膜阀TWV 三通阀SGV 插板阀6.管道上用的小型设备SPR 气液分离器Separator FA 阻火器Flame arresterSR 过滤器 StrainerSRY Y型过滤器 Y-type strainerSRT T型过滤器 T-type strainerSRB 桶式过滤器 Bucket type strainerTSR 临时过滤器 Temporary strainerSIL 消声器 SilencerSG 视镜 Slight glassSC 取样冷却器 Sample coolerDF 排液漏斗 Drain funnelLM 管道混合器 Line mixerRO 限流孔板 Restriction orificeMO 混合孔板 Mixing orificeRD 爆破片（爆破膜） Rupture diskEJ 补偿器 Expansion joint7.隔热、伴热 INS 隔热 Thermal insulationH 保温 Hot insulationC 保冷 Cold insulationP 防烫伤隔热 Personnel protection insulationT&I 伴热 Tracing and insulationT 管道伴热（冷） TracingEST 蒸汽外伴热 External steam tracingIST 蒸汽内伴热 Internal steam tracingSJT 蒸汽夹套伴热 Steam-jacket tracingET 电伴热 Electric tracing8.配管材料和等级 M 金属材料 Metallic material CS 碳钢 Carbon steelCAS 铸钢 Cast steelFS 锻钢 Forged steelAS 合金钢 Alloy steelSS 不锈钢 Stainless steelAUSTSS 奥氏体不锈钢 Austenitic stainless-steelCI 铸铁 Cast ironMI 可锻铸铁 Malleable ironDI 球墨铸铁 Ductile ironAL 铝 AluminumBRS 黄铜 BrassBRZ 青铜 BronzeCU 紫铜 CopperLAS 低合金钢 Low alloy steelFLAS 低合金锻钢 Forged low alloy steelCLAS 低合金铸钢 Cast low alloy steelTHK 壁厚 ThicknessSCH 表号 Schedule numberSTD 标准 StandardXS 加强 Extra strongXXS 特强 Double extra strong9.装置布置 CN 建北 Construction northE 东 EastW 西 WestS 南 SouthN 北 NorthH 水平 HorizontalV 竖直、铅直、直立 VerticalGRD 地坪 GroundUG 地下 UndergroundBL 装置边界线 Battery limit lineESEW 事故沐浴洗眼器 Emergency shower and eye washer HS 软管站 Hose stationML 接续分界线 Match linePS 管道支架（管架） Piping support。
给排水常用专有名词中英文对照
给排水常用专有名词中英文对照Introduction给排水工程是指在建筑物内设置一定的设施，以便实现供水、排水、雨水排放和污水处理等功能的工程。
在给排水领域，有很多专有名词，这些名词在建筑设计与施工过程中至关重要。
本文将介绍给排水常用专有名词的中英文对照，以帮助读者更好地了解这些名词的含义。
Pipes1. 水管Water Pipe水管是用来输送清洁水的管道。
水管通常使用聚乙烯、聚氯乙烯、水泥、铸铁等材料制成。
其直径有大小之分，根据工程需要进行选择。
2. 排水管Drain Pipe排水管是用来排放生活污水和雨水的管道。
排水管通常使用聚氯乙烯、铸铁、水泥、预制混凝土等材料制成，其直径大小也有不同规格。
3. 初次排污管Primary Drain Pipe初次排污管通常指从家庭、工厂、商场等的“首次”排污管。
这类管道的直径通常比较大，材料较粗，以便排放大量的污水。
4. 无压排水管Non-pressure Drain Pipe无压排水管是一种不需要压力的排水管道。
这种管道通常建立在建筑物的低处，以便将污水顺利排放出去。
5. 垂直排水管Vertical Drain Pipe垂直排水管是指垂直于地面的排水管道，主要负责将生活污水从建筑物内部排放出去。
Fittings1. 水管接头Water Pipe Joint水管接头通常用于连接水管，其形状很多，可以根据实际需要选择不同类型的接头。
例如，有夹紧接头、螺旋接头等。
2. 排水管接头Drain Pipe Joint排水管接头是用来连接排水管的管道连接件。
这类接头通常是由橡胶、铸铁等材料制成。
3. 弯头Elbow弯头是一种用于改变管道方向的管道连接件，通常由铸铁、钢、铜等材料制成。
4. 管道三通Tee管道三通是一种管道连接件，通常用于将三个管道连接在一起。
这种连接件可以分为不等口径三通和等口径三通。
Valves1. 关闭阀门Stop Valve关闭阀门是一种管道阀门，通常用于中止管道内的水流，以便对管道进行维修或更换。
给排水专业英语考试词汇
house water-supply system 建筑给水系统flange 法兰gate valve 闸阀communication pipe 引入管interior water-supply system室内给水系统domestic water-supply system 生活给水系统fire-protection water-supply system 消防给水系统industrial water-supply system 生产给水系统meter box 仪表点（段）pressure booster 增压设备storage tank 贮水箱piping line 管道water-dispensing fixture 配水器具de-aerator 除氧器hot water-supply system 热水供应系统water meter 水表cistern 水塔，水箱，水池air-operated water-dispensing tank 气压给水设备split system 分区系统series system 串联系统parallel system 并联系统fire line 消防管道fire hose 灭火水龙带hose barrel 水枪fire brigade 消防队standby pump 备用泵fire-line outlet 消火栓（箱）fire valve (指消火栓箱中的)阀门globe valve 球阀standpipe 立管control valve 控制阀sprinkler head 喷头sprinkler systems 喷淋系统drencher systems 水幕系统house drainage system 建筑排水系统sanitary drainage system 生活排水系统industrial drainage system 生产排水系统storm water(rainwater) drainage system 雨水排水系统fixture trap 存水弯plumbing fixture 卫生器具drainage piping 排水管道manhole 人孔，检查井building(house) connection 排水出户管（排出管）lift pumping plant(station) 提升泵站public sewer 市政管道（室外管网）bathtub 浴盆sitting tub 坐式浴盆shower stall 淋浴房washbasin 洗手盆bidet 坐便器single-bowl sink 单格洗涤盆double-bowl sink 双格洗涤盆。
管道工程常用英文术语
管道工程常用英文术语管道conduit,pipeline,duct工业管道industrial pipeline给水管道water supply conduit(pipeline)输水管道water transmission conduit(pipeline)配水管道water distribution pipeline排水管道sewer conduit(pipeline)雨水管道storm sewer conduit(pipeline)河流管道combined drainage conduit(pipeline)污水管道sewage conduit(pipeline)管道结构pipeline(conduit)stucture埋地管道,地下管道buried conuit(pipeline),under-ground conduit (pipeline)地上管道above=ground conduit(pipeline)水下管道submerged pipeline,subaqueous pipeline海底管道submarine pipeline架空管道overhead pipeline管桥pipe bridge涵洞culvert建筑给水管道pipeline for water supply in building建筑排水管道pipeline for waste water(sewerage)in building雨落管down pipe,down spout冷却水管道cooling water pipeline输油管道petroleum transmission pipeline输气管道gas transmission pipeline供热管道heat-supply pipeline采暖管道heating pipeline通风管道ventilating duct细颗粒固体输送管道finely divided solid transmission pipeline管沟pipe duct电缆沟cable duct通行地沟accessible duct不通行地沟unpassable duct综合管道，共同沟combined duct电工套管electrical conduits无压管道non-pressure conduit(pipeline)自流管道，重力流管道free-flow conduit(pipeline),gravity-flow conduit (pipeline)管道穿越pipeline under crossing管道跨越pipeline aerial(over)crossing管道支架pipeline trestle管道支墩pipeline pier刚性管rigid pipe柔性管flexible pipe半柔性管，半刚性管semi-flexible pipe,semi-rigid pipe内衬liner涂层coating,surface layer管道接头pipeline joint管件pipe fitting管道附件pipe accessory管道附属构筑物pipeline appurtenance止推墩，固定墩thrust blocks,anchor管道防腐corrosion prevetive of pipes管道隔热，管道保温thermal insulation of pipes钢管steel pipe焊接钢管welded steel pipe无缝钢管seamless steel pipe螺旋焊接钢管spiral welded steel pipe直缝焊接钢管longitudinal welded steel pipe电阻焊electirc resistence welding,ERW不锈钢管stainless steel pipe合金钢管alloy steel pipe铸铁管cast iron pipe(CIP)灰口铸铁管grey cast iron pipe(CIP)稀土铸铁管rare earth cast iron pipe球墨铸铁管，可延性铸铁管nodular castiron pipe,ductile cast iron pipe (DIP)铸态球墨铸铁管unannealed nodular(ductile)cast iron pipe混凝土管concrete pipe(CP)钢筋混凝土管reinforced concrete pipe(RCP)预应力混凝土管prestressed concrete pipe(PCP)自应力混凝土管self-prestressed concrete pipe,chemically prestressed concrete pipe预应力钢筒混凝土管prestressed concrete cylinder pipe(PCCP)内衬式预应力钢筒混凝土管lined type PCCP(PCCR-L),lined-cylinder pipe (LCP)埋置式预应钢管混凝土管embedded type PCCP(PCCP-E),embeded-cylinder pipe(ECP)石棉水泥管asbestos-cement pipe(ACP)陶土管vitrified clay pipe硬聚氯乙烯塑料管unplasticised polyvinyl chloride pipe(UPVC管)聚乙烯塑料管polyethylene pipe(PE管)聚丙烯塑料管polypropylene pipe(PP管)聚丁烯塑料管polybutylene pipe(PB管)红泥聚氯乙烯耐候塑料管red mud plastic anti-weather pipeABS工程塑料管acrylonitrile butadiene stryrene pipe(ABS管)玻璃纤维管，玻璃纤维增强热固性塑料管fiberglass reinforced pipe(FRP), glass fibre reinforced plastics pipe(GRP)增强热固性树脂管reinforced thermosetting resin pipe(RTRP)增强塑料砂浆管reinforced plastic mortar pipe(RPMP)复合管composite pipe混合结构管道mixed structure conduit圆形管道circular conduit(pipeline)矩形管道box(rectangular)conduit马蹄形管道horseshoe conduit半椭圆形管道semi-elliptical conduit椭圆形管道oval conduit,elliptical conduit卵形管道ovoid conduit波纹管corrugated pipe螺纹状helical corrugation圆圈状annular corrugation单壁波纹管single wall corrugated pipe双臂波纹管double wall corrugated pipe波纹钢管corrugated steel pipe波纹塑料管corrugated plastic pipe异型（肋型）塑料管profile(ribbed)wall plastic pipe开孔肋形管open profile pipeT形肋T-rib section竖肋vertical rib section闭孔肋形管closed profile pipe发泡塑料管plastic sandwich pipe保护套管protective cased pipe双层管pipe in pipe平口管straight butt(plain)end pipe斜口管beveled pipe,splayed end pipe承口管socket pipe企口管tongue and groove pipe,rebated pipe现浇管道cast-in-place(situ)conduit预制装配管道precast fabricated conduit离心法centrifugal process连续浇筑法continuous casting process砂型浇注法sand box casting process悬辊法roller suspension process径向挤压法，立式挤压法vertical compressed casting process立式振捣法vertical vibrated casting process芯模振捣法core vibrated casting process振动台振捣法table vibrated casting process。
化工管道工程使用技术词汇中英文对照
化工管道工程使用技术词汇中英文对照1 管道组成件Piping ponent1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube 钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe 铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbowk半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand) 异径三通（分支口为异径）reducing tee (reducing on outlet)异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet)异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull head)45°斜三通45° lateral45°斜三通（支管为异径）45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run)45°斜三通(一个直通口及支管为异径) 45° lateral (reducing on one run and branch)Y型三通（俗称裤衩）tr ue “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and outlet)异径四通（两个分支口为异径）reducing cross (reducing on both outlet) 异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run and both outlet)异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss管接头coupling, full coupling半管接头half coupling异径管接头reducing coupling活接头union内外螺纹缩接（俗称补芯）bushing管帽cap (C)堵头plug短节nipple异径短节reducing nipple; swage nipple1.3 弯管Bend预制弯管fabricated pipe bend跨越弯管（^ 形）cross-over bend偏置弯管（~ 形）offset bend90°弯管quarter bend环形弯管cirele bend单侧偏置90°弯管（? 形）single offset quarter bendS形弯管“S” bend单侧偏置U形膨胀弯管（| ?形）single offset “U” bend U形弯管“U” bend双偏置U膨胀弯管double offset expansion “U” bend斜接弯管mitre bend三节斜接弯管3-piece mitre bend折皱弯管corrugated bend圆度roundness1.4 法兰Flange (FLG）整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰（包括平焊法兰）slip-on flange (SO); slip-on welding flange 承插焊法兰socket welding flange松套法兰lap joint flange (LJF)对焊法兰welding neckflange (WNF)法兰盖blind flange, blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange对焊环welding neck collar （与stub end相似）平焊环welding-on collar突缘短节stub end, lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating, pressure rating class压力—温度等级pressure-temperature rating法兰密封面，法兰面flange facing突面raised face (RF)凸面male face (MF)凹面female face (FMF)榫面tongue face槽面groove face环连接面ring joint face全平面；满平面flat face; full face (FF)光滑突面smooth raised face (SRF)法兰面加工facing finish粗糙度roughness光滑的smooth齿形serrated均方根root mean square (RMS)算术平均粗糙高度arithmetical average roughness height (AARH) 配对法兰panion-flange螺栓圆bolt circle (B.C.)1.5 垫片Gasket (GSKT)垫片的型式type of gasket平垫片flat gasket环形平垫片flat ring gasket平金属垫片flat metal gasket夹棉织物的橡胶elastomer with cotton fabric insertion夹石棉织物的橡胶elastomer with asbestos fabric insertion夹石棉织物及金属丝加强的橡胶elastomer with asbestos fabric insertion and with wire reinforcement无石墨压缩白石棉垫片non graphited pressed white asbestos gasket天然白橡胶垫片natural white rubber gasket压缩石棉垫片pressed asbestos class gasket浸聚四氟乙烯的石棉垫片PTFE impregnated asbestos gasket夹石棉的缠绕金属垫片spiral-wound metal gasket with asbestos filler 内环inner ring外环，外定位环outer ring波纹金属垫片corrugated metal gasket波纹金属包嵌石棉垫片corrugated metal gasket with asbestos inserted 双夹套波纹金属包石棉垫片corrugated metal double jacketed asbestos filled gasket双夹套垫片double jacketed gasket金属包石棉平垫片flat metal jacketed asbestos filled gasket整体金属齿形垫片solid metal serrated gasket槽形金属垫片grooved metal gasket环形连接金属垫片ring joint metal gasket八角环形垫片octagonal ring gasket椭圆环形垫片oval ring gasket透镜式垫片lens gasket非金属垫片non-metallic gasket1.6 阀门Valve1.6.1 阀门结构、零件阀轭yoke外螺纹阀杆及阀轭outside screw and yoke (OS & Y) 阀杆stem内螺纹inside screw (IS)阀轭套yoke sleeve阀杆环stem ring阀座valve seat (body seat)阀座环、密封圈seat ring整体（阀）座integral seat堆焊（阀）座deposited seat阀芯（包括密封圈、杆等内件）trim阀盘disc阀盘密封圈disc seat阀体body阀盖bonnet阀盖衬套bonnet bush螺纹阀帽screw cap螺纹阀盖screw bonnet螺栓连接的阀盖bolted bonnet (BB) 活接阀盖（帽）union bonnet (cap) 螺栓连接的阀帽bolted cap (BC)焊接阀盖welded bonnet (WB)本体阀杆密封body stem seal石棉安全密封asbestos emenen seal 倒密封back seal压力密封的阀盖pressure-tight bonnet 动力操纵器powered operator电动操纵器electric motor operator气动操纵器pneumatic operator液压操纵器hydraulic operator快速操纵器quick-acting operator滑动阀杆sliding stem正齿轮传动spur gear operated伞齿轮传动bevel gear operated扳手操作wrench operated链轮chain wheel手轮hand wheel手柄hand lever (handle)气缸（或液压缸）操纵的cylinder operated链条操纵的chain operated等径孔道full bore; full port异径孔道reducing bore, reduced port,venturi port 短型short pattern紧凑型（小型）pact type笼式环lantern ring压盖gland阀杆填料stem packing阀盖垫片bonnet gasket升杆式（明杆）rising stem (RS)非升杆式（暗杆）non-rising stem (NRS)指示器/限位器indicator/stopper注油器grease injector可更换的阀座环renewable seat ring1.6.2 常用阀(1）闸阀gate valve平行双闸板double disc parallel seat开口楔形闸板split wedge挠性整体楔形闸扳flexible solid wedge整体楔形闸板solid wedge塞型闸阀plug gate valve直通型闸阀through conduit gate valve(2) 截止阀globe valve球心型阀盘globe type disc塞型阀盘plug type disc可转动的阀盘swivel disc(3) 节流闪阀throttle valve针阀needle valve(4) 角阀angle valve(5) Y型阀（Y 型阀体截止阀）Y-valve (Y-body globe valve)(6) 球阀ball valve三通球阀3-way ball valve装有底轴的trunnion mounted耐火型fire safe type浮动球型floating ball type防脱出阀杆blowout proof stem(7) 蝶阀butterfly valve对夹式（薄片型）wafer type凸耳式lug type偏心阀板蝶阀offset disc burerfly valve; eccentric butterfly valve 斜阀盘蝶阀canted disc butterfly valve连杆式蝶阀link butterfly valve8) 柱塞阀piston type valve(9) 旋塞阀plug valve三通旋塞阀three-way plug valve四通旋塞阀four-way plug valve旋塞cock衬套旋塞sleeve cock(10) 隔膜阀diaphragm valve橡胶衬里隔膜阀rubber lined diaphragm valve直通式隔膜阀straight way diaphragm valve堰式隔膜阀weir diaphragm valve(11) 夹紧式胶管阀pinch valve（用于泥浆、粉尘等）(12) 止回阀check valve升降式止回阀lift check valve旋启式止回阀swing check valve, flap check valve落球式止回阀ball check valve弹簧球式止回阀spring ball check valve双板对夹式止回阀dual plate wafer type check valve无撞击声止回阀non-slam cheek valve底阀foot valve切断式止回阀stop check valve; non-return valve活塞式止回阀piston check valve斜翻盘止回阀tilting disc check valve蝶式止回阀butterfly check valve1.6.3 其它用途的阀安全泄气阀safety valve (SV)安全泄液阀relief valve (RV)安全泄压阀safety relief valve杠杆重锤式lever and weight type引导阀操纵的安全泄气阀pilot operated safety valve复式安全泄气阀twin type safety valve罐底排污阀flush-bottom tank valve电磁阀solenoid valve, solenoid operated valve电动阀electrically operated valve, electric-motor operated valve 气动阀pneumatic operated valve低温用阀cryogenic service valve蒸汽疏水阀steam trap机械式疏水阎mechanical trap浮桶式疏水阀open bucket trap, open top bucket trap浮球式疏水阀float trap倒吊桶式疏水阀inverted bucket trap自由浮球式疏水阀loose float trap恒温式疏水阀thermostatic trap金属膨胀式蒸汽疏水阀metal expansion steam trap液体膨胀式蒸汽疏水阀liquid expansion steam trap双金属膨胀式蒸汽疏水阀bimetallic expansion steam trap压力平衡式恒温疏水阀balanced pressure thermostatic trap热动力式疏水阀thermodynamic trap脉冲式蒸汽疏水阀impulse steam trap放气阀（自动放气阀）air vent valve (automatic air vent valve) （疏水阀用）平板式滑动闸阀slab type sliding gate valve盖阀flat valve换向阀diverting valve, reversing valve热膨胀阀thermo expansion valve自动关闭阀self-closing gate valve自动排液阀self-draining valve管道盲板阀line-blind valve挤压阀squeeze valve（用于泥浆及粉尘等）呼吸阀breather valve风门、挡板damper减压阀pressure reducing valve, reducing valve 控制阀control valve膜式控制阀diaphragm operated control valve执行机构actuator背压调节阀back pressure regulating valve差压调节阀differential pressure regulating valve 压力比例调节阀pressure ratio regulating valve1.6.4 未指明结构（或阀型）的阀切断阀block valve; shut-off valve; stop valve调节阀regulating valve快开阀quick opening valve快闭阀quick closing valve隔断阀isolating valve三通阀three way valve夹套阔jacketed valve非旋转式阀non-rotary valve排污阀blowdown valve集液排放阀drip valve排液阀drain valve放空阀vent valve卸载阀unloading valve排出阀discharge valve吸入阀suction valve多通路阀multiport valve取样阀sampling valve手动阀hand-operated valve; manually operated valve 锻造阀forged valve铸造阀cast valve（水）龙头bibb; bib; faucet抽出液阀（小阀）bleed valve旁路阀by-pass valve软管阀hose valve混合阀mixing valve破真空阀vacuum breaker冲洗阀flush valve第一道阀；根部阀primary valve根部阀root valve总管阀header valve事故切断阀emergency valve1.7 管道特殊件Piping Specialty1.7.1 管道特殊件（组件）粗滤器strainer过滤器filter临时粗滤器（锥型）temporary strainer (cone type) y 型粗滤器y-type strainerT型粗滤器T-type strainer永久过滤器permanent filter丝网粗滤器gauze strainer洗眼器及淋浴器eye washer and shower视镜sight glass阻火器flame arrester喷嘴；喷头spray nozzle取样冷却器sample cooler消声器silencer膨胀节expansion joint波纹膨胀节bellow expansion joint单波single bellow双波double bellow多波multiple bellow压力平衡式膨胀节pressure balanced expansion带铰链膨胀节hinged expansion joint轴向位移型膨胀节axial movement type expansion joint 自均衡膨胀节（外加强环）self-equalizing expansion joint 带接杆膨胀节tied expansion joint万向型膨胀节universal type expansion joint球形补偿器ball type expansion joint填函式补偿器slip type (packed type) expansion joint单向滑动填料函补偿器single actionpacked slip joint1.7.2 管道特殊元件Piping Special Element软管接头hose connection (HC)快速接头quick coupling金属软管metal hose橡胶管rubber hose挠性管flexible tube鞍形补强板reinforcing saddles补强板reinforcement pad特殊法兰special flange漏斗funnel排液环drip ring排液漏斗drain funnel插板blank垫环spacer8字盲板spectacle blind; figure 8 blind限流孔板restriction orifice爆破片rupture disk法兰盖贴面protective disc费托立克接头victaulic coupling1.8 端部连接End Connection法兰端flanged end坡口端beveled end (BE)对焊端butt welded end平端plain end (PE)承插焊端socket welding end螺纹端threaded end (TE)承口bell end焊接端welding end法兰连接（接头）flanged joint对焊连接（接头）butt welded joint螺纹连接，管螺纹连接threaded joint, pipe threaded joint 锥管螺纹密封焊连接seal-welded taper pipe threaded joint 承插焊连接（接头）socket welded joint承插连接（接头）bell and spigot joint环垫接头ring joint (RJ)万向接头universal joint软钎焊连接（接头）soldered joint搭接接头，松套连接lapped joint外侧厚度切斜角bevel for outside thickncss内侧厚度切斜角bevel for inside thickness内外侧厚度切斜角bevel for bined thickness法兰式的flanged (FLGD)对焊的butt welded (BW)螺纹的threaded (THD)承插焊的socket welded (SW)小端为平的small end plain (SEP)大端为平的large end plain (LEP)两端平both ends plain (BEP)小端带螺纹small end thread (SET)大端带螺纹large end thread (LET)两端带螺纹both end thread (BET)一端带螺纹one end thread (OET)支管连接branch connection焊接支管branch pipe welded directly to the run pipe2 管道用紧固件及螺纹2.1 紧固件螺栓bolt六角头螺栓hexagonal head bolt方头螺栓square head bolt螺柱，双头螺栓stud bolt环头螺检eye bolt沉头螺栓countersunk (head) screw 地脚螺栓anchor bolt; foundation bolt 松紧螺旋扣（花篮螺丝）turnbuckle U形螺栓U-boltT形螺栓T-bolt圆头螺钉round head bolt机螺栓，机螺钉maehine bolt顶开螺栓，顶起螺栓Jack screw自攻螺钉self tapping screw膨胀螺栓expansion bolt粗制的coarse精制的finished, fine螺母nut六角螺母hexagonal nut方螺母square nut蝶形螺母wing nut扁螺母flat nut锁紧螺母lock nut垫圈washer平垫圈plain washer球面垫圈spherical washer 弹簧垫圈spring washer方垫圈square washer斜垫圈slant washer销轴pinned shan销pin开口销cotter pin定位销dowel pin带孔销pin with hole圆锥销taper pin铆钉rivet键key2.2 螺纹左螺纹left hand thread右螺纹right hand thread 管螺纹pipe thread锥管螺纹taper pipe thread直管螺纹straight pipe thread梯形螺纹trapezoid thread螺距pitch of thread粗牙螺纹coarse thread细牙螺纹fine thread特细牙螺纹extra fine thread通长螺纹full thread惠氏螺纹whitworth thread公制螺纹metric ibread美国标准锥管螺纹American standard taper pipe thread (NPT) 螺孔tap3 材料、型钢及填料3.1 金属材料3.1.1 黑色金属Ferrous Metal碳素钢carbon steel (CS)低碳钢low-carbon steel中碳钢medium-carbon steel高碳钢high-carbon steel普通碳素钢general carbon steel优质碳素钢high-quality carbon steel普通低合金结构钢general structure low-alloy steel合金结构钢structural alloy steel合金钢alloy steel低合金钢low alloy steel中合金钢medium alloy steel高合金钢high alloy steel耐热钢heat resisting steel高强度钢high strength steel复合钢clad steel工具钢tool steel弹簧钢spring steel钼钢molybdenum steel镍钢nickel steel铬钢chromium steel铬钼钢chrome-molybdenum steel铬镍钢chromium-nickel steel,chrome-nickel steel 不锈钢stainless steel (S.S.)奥氏体不锈钢Austenitic stainless steel马氏体不锈钢Martensitic stainless steel司特来合金（钨铬钴台金）Stellite耐蚀耐热镍基合金Hastelloy铬镍铁合金inconel耐热铬镍铁合金incoloy20合金20 alloy平炉钢（马丁钢）Martin steel镇静钢killed steel半镇静钢semi-killed steel沸腾钢rimmed steel; rimming steel; open-steel 锻钢forged steel铸钢cast steel铸铁cast iron (C.I.)灰铸铁grey cast iron可锻铸铁malleable iron (MI)球墨铸铁nodular cast iron; nodular graphite iron 生铁pig iron熟铁，锻铁wrought iron铸件casting高硅铸铁high silicon cast iron3.1.2 镀层及制造方法渗铬钢，镀铬钢chromized steel镀铬的chromium-plated, chrome-plated镀层plating锻造，型钢swage锻造的，锻造forging轧制rolling热轧hot rolling冷轧cold rolling挤压extruding冷加工cold working热加工hot working拔制drawing3.1.3 有色金属Non-ferrous Metal 铝aluminum铜，紫铜copper黄铜brass青铜bronze铝青铜aluminum bronze磷青铜phosphor bronze铝镁合金aluminum magnesium锰青铜manganese bronze蒙乃尔（注：镍及铜合金）Monel 镍铜台金nickel copper alloy非铁合金nonferrous alloy钛titanium铅lead硬铅hard lead3.1.4 材料性能极限强度ultimate strength抗拉强度tensile strength屈服极限yield limit屈服点yield point延伸率percentage elongation抗压强度pressive strength抗弯强度bending strength弹性极限elastic limit冲击值impact value疲劳极限fatigue limit蠕变极限creep limit持久极限endurance limit布氏硬度Brinell hardness洛氏硬度Rockwell hardness维氏硬度Vickers diamond hardness, diamond penetrator hardness 蠕变断裂强度creep rupture strength断面收缩率reduction of area韧性toughess脆性brittleness延性ductility冷脆cold shortness冷流cold flow3.2 非金属材料Non-metallic Material塑料plastic丙烯腈—丁二烯—苯乙烯acrylonitrile-butadiene-styrene (ABS) 聚乙烯polyethylene (PE)聚氯乙烯polyvinyl chloride (PVC)苯乙烯橡胶styrene-rubber (SR)聚丁烯polybutylene (PB)聚丙烯polypropylene (PP)聚苯乙烯polystyrene (PS)氯化聚醚chlorinated polyether (CPE)聚酰胺polyamide (PA)聚碳酸酯polycarbonate (PC)聚甲基丙烯酸甲酯polymethyl methacrylate (PMMA)醋酸丁酸纤维素cellulose acetate butyrate (CAB)氯化聚氯乙烯chlorinated polyvinyl chloride (CPVC)聚偏二氟乙烯polyvinylidene fluoride (PVDF)缩醛塑料acetal plastic尼龙塑料nylon plastic聚烯烃polyolefin (PO)石墨酚醛塑料graphite phenolic plastics聚四氟乙烯polytetrafluoroethylene (PTFE)纤维增强热塑性塑料fiber reinforced thermoplastics热塑性塑料thermoplastic热固性塑料thermosetting plastics胶粘剂adhesive溶剂胶接剂solvent cement树脂resin环氧树脂epoxy, epoxy resin聚酯树脂polyester resin聚酯纤维polyester fibers氟塑料fluoroplastics聚氨基甲酸酯polyurethane丙烯酸树脂acrylic resin脲醛树脂urea resin呋哺树脂furan resin乙烯丙烯二烃单体ethylene propylene diene monomer (EPDM) 合成橡胶synthetic rubber橡胶rubber丁腈橡胶nitrile butadiene rubber氯丁橡胶neoprene天然橡胶natural rubber乙丙橡胶ethylene propylene rubber (EPR)玻璃glass硼硅玻璃borosilicate glass耐火砖fire brick陶瓷ceramic搪瓷porcelain enamel木材wood3.3 型材型钢shaped steel, section steel, swage 角钢angle steel槽钢channel工字钢I-beam宽缘工字钢或H钢wide flanged beam T型钢T-bar方钢square bar扁钢flat bar角钢hexagonal steel bar圆钢round steel; rod钢带strap steel钢板plate网纹钢板checkered plate腹板（指型钢的立板）web翼缘（指型钢的缘）wing3.4 填料及填料函填料packing石棉绳asbestos rope, asbestos cord．O形环O-ring自密封self-sealing四氟带Teflon tap带铬镍合金丝的石棉绳asbestos rope with inconel wire, inconel wire asbestos浸聚四氟乙烯的石棉填料Teflon impregnated asbestos packing金属填料metallic stuffing填料箱，填料函packing box, stuffing box填料函压盖stuffing box gland4 管道等级及材料统计4.1 管道材料规定Piping Material Specification管道等级piping class; piping classification管道等级号class designation公称直径nominal diameter (DN); nominal (pipe) size公称压力nominal pressure (PN)压力级，等级，类别class (CL)低压low pressure (L.P.)中压medium pressure (M.P.)高压high pressure (H.P.)大气压atmosphere (ATM)真空vacuum工作压力operating pressure; working pressure设计压力design pressure工作温度operating temperature设计温度design temperature环境温度ambient temperature腐蚀裕量corrosion allowance管道附件piping attachment管道元件piping element壁厚wall thickness (WT)壁厚系列号schedule number (SCH. No.)加厚的，加强的extra heavy, extra strong双倍加厚的，双倍加强的double extra heavy, double extra strong通用连接组typieal installation分组（类）形式（如管道等级表）block form数据库data base文件file4.2 材料统计Material Take-off (MTO)汇总表summary sheet材料表bill of material (BM)综合管道材料表consolidated piping material summary sheet (CPMSS) 统计材料准确度accuracy of take-off材料情况报告material status report (MSR)散装材料bulk material编位号的itemized代码code number短代码short code数量quantity (QTY)重力weight净重net weight毛重gross weight5 设备布置及管道布置Plot Plan and Piping Layout,Equipment and Piping Arrangement 5.1 设备名称Equipment Name5.1.1 容器Vessel(1) 塔tower, column洗涤塔scrubber吸收塔absorber冷却塔cooling tower精馏塔fractionating tower蒸馏塔distillation tower再生塔regenering tower造粒塔prflling tower汽提塔stripper脱气塔degasifier合成塔synthesis tower(2) 反应器reactor聚台釜polymerizer转化器，变换器converter脱硫反应器desulphurization reactor 甲烷化器methanator(3) 气柜gas-holder螺旋式气柜helical gas-holder湿式气柜wet gas-holder干式气柜dry gas-holder(4) 槽罐贮罐tank; storage tank缓冲罐knock out drum球罐spheroid, spherical tank罐drum接受槽receiver计量槽measuring tank加料槽feed tank排污罐blow down tank闪蒸罐flash drum汽包steam drum溶液贮槽solution storage tank 地下槽sloptank(5) 其它设备分离器separator旋风分离器cyclone分子筛molecular sieve脱氧器deaerator搅拌器agitator干燥器dryer混合器mixer萃取器extractor结晶器crystallizer澄清器gravity settler净化器purifier气化器vaporizer吸附器adsorber融解槽melter减温器desuperheater升压器booster喷射器ejector喷头sprayer火炬flare消声器silencer(6) 换热器、加热器、冷却器换热器heat exchanger空冷器air cooler水冷却器water cooler冷凝器condenser螺旋板式换热器spiral plate heat exchanger 蒸发器evaporator再沸器reboiler急冷器quencher深冷器chiller预热器preheater再热器reheater加热器heater电加热器electric heater过热器super heater给水加热器feed water heater中间冷却器inter cooler后冷却器after cooler5.1.2 工业炉及锅炉炉子furnace烧嘴burner锅炉boiler烟囱stack废热锅炉waste heat boiler辅助锅炉auxiliary boiler省煤器economizer回热炉direct-fired heater辐射段radiant section对流段convection section裂化炉reformer焚烧炉incinerator回转窑rotary kiln炉管furnace tube吹灰器soot blower观察孔observation door, peep door防爆门explosion door5.2 辅助用房名称5.2.1 生产用房分析室analyzer room变压器室transformer room配电室，变电所substation, switch room 蓄电池室battery room控制室control room通风室ventilating room贮藏室storage room维修间maintenance room办公室office5.2.2 生活用房更农室locker room盥洗室，厕所closet, lavatory, toilet5.3 图名管道布置平面piping arrangement plan (PAP)管道布置piping layout轴测图isometric drawing分区索引图key plan初版设备布置图（“A”版）preliminary plot plan ( “A” issue)内部审查版设备布置图（“B”版）inrernal approval plot plan ( “B” issu e) 用户审查版设备布置图（“C”版) owner approval plot plan ( “C” issue)确认版设备布置图（“D”版）confirm plot plan ( “D” issue)研究版设备布置图（“e”版）planning plot plan ( “E” issue)设计版设备布置图（“F”）designing plot plan ( “F” issue)施工版设备布置图（“G”版）construction plot plan ( “G” issue)5.4 厂房、站、单元压缩机房pressor house (room)泵房pump house (room)洗眼站eye washer station泡沫站foam station软管站，公用工程站hose station (HS), utility station 成套设备package unit设施facilities罐区tank yard空分装置air separation facility5.5 设备布置设备位号equipment item number工厂plant工厂区界plant limit项目区界内侧inside battery limit (I.S.B.L.)项目区界batterylimit (BL)区界area limit区域边界zone iimit界外off site东east (E)西west (W)南south (S)北north (N)上up下down工厂北向plant north真实北向true north道路road小过道cat walk, cat way走道，过道walk way, gangway, access way 污水坑（井）sump pit集水池catch basin沟槽through预留区trough场地future area铺砌区paving area非铺砌区unpaved area碎石铺面gravel paving橡皮铺面rubber paving面积，区域area体积，容积volume (VOL)5.6 管道布置管道设计piping design管道研究piping study走向研究routing study重要管道critical piping地上管道above ground piping 地下管道under ground piping 管网network of pipes管廊pipe rack管沟piping trench管间距line spacing管道跨距line span总管header, manifold旁路by pass排液drain放空vent上升管，垂直管riser导管canduit裸管bare iine管件直接fitting to fitting (FTF) 管段，接口spool piece, spool 取样接口sampling connection 集液包drip leg伴热管tracing pipe蒸汽伴热steam tracing热水伴热hot-water tracing电伴热electrical tracing夹套管jacketed line, jacketed piping 全夹套的full jacketed平面plan详图detail“ ”视图X view “X”“ ”剖视A-A section “A-A”连接图hook up drawing接续图continue on drawing (COD) 接续线match line (M.L.)比例scale图例legend符号symbol管口表list of nozzles方位orientation管口方位nozzle orientation定位location相交intersection水平的horizontal垂直的，立式的vertical垂直，正交，垂直的perpendicular 平行，平行的parallel水平安装horizontal installation垂直安装vertical installafion对称的symmetric相反（的），对面（的）opposite顺时针方向clock wise逆时针方向counter clock wise计算机辅助设计puter aided design (CAD)5.7 图面标注绝对标高abselute elevation海平面标高over-sea mean level (OSL)标高，立面elevation (EL)混凝土顶面top of concrete架顶面top of support (TOS)钢结构顶面top of steel梁项面top of beam (TOB)支撑点point of suppon (POS)管顶top of pipe (TOP)管底bouom of pipe (BOP)沟底boaom of trench管子内底invert (inside bottom of pipe)底平flat on bottom (FOB)顶平flat on top (FOT)工作点working point (W.P.)面至面face to face (F-F)中心至端面center to end (C-E)中心至面center to face (C-F)中心至中心，中至中center to center (C-C) 坐标coordinate坐标原点origin of coordinate出口中心线center line of discharge入口中心线center line of suction中心线centerline (CL)入口inlet, suction出口outlet, discharge排出口exhaust距离distance5.8 相关专业的专业词汇5.8.1 工艺(1) 图及表流程图flow diagram工艺流程图process flow diagram (PFD)管道及仪表流程图piping and instrument flow diagram (PID)公用工程流程图utility flow diagram (UFD) 管线表line list; line schedule命名表；管道表nomenclature设备表equipment list (schedule)(2) 流体fluid空气air仪表空气instrument air工艺空气process air低压蒸汽low pressure steam中压蒸汽medium pressure steam高压蒸汽high pressure steam伴热蒸汽tracing steam饱和蒸汽saturated steam过热蒸汽superheated steam氧气oxygen氢气hydrogen氮气nitrogen燃料气fuel gas天然气natural gas火炬气flare gas酸性气sour gas液化石油气liquefired petroleum gas (LPG)氨气ammonia gas冷却水cooling循环水circulating water锅炉给水boiler feed water热水hot water蒸汽冷凝水steam condensate 盐水brine工艺水process water化学污水chemical sewage防腐剂corrosion inhibitor重油heavy oil石脑油naphtha燃料油fuel oil润滑油lubricating oil密封油sealing oil冷冻剂refrigerant载热体heating medium溶剂solvent溶液solution母液mother liquor单体monomer聚合物polymer均聚物homopolymer共聚物copolymer工艺液体process liquid工艺气体process gas硫酸sulphuric acid盐酸chlorhydric acid硝酸nitric acid烧碱caustic soda(3) 流体特性fluid characteristics 蒸汽压vapor pressure临界温度critical temperature临界点critical point临界压力critical pressure比热specific heat湿度humidity密度density比重specific gravity粘度viscosity闪点flash point融点melting point凝固点freezing point浓度concentration爆炸极限limit of explosion有毒的toxic可燃的；易燃的flammable(4) 其它回收recovery再生regeneration循环cireulatlon再循环；再生recycle补充make-up制备preparation蒸汽吹扫steaming out吹扫purge抽空；排空evacuation吹出blow-off排污blow down破真空vacuum breaker大气腿barometric leg备用stand-by化学清洗chemical cleaning净正吸入压头net positive suction head (NPSH) 进料feed成品product污染contamination大气污染atmospheric pollution环境温度ambient temperature5.8.2 建筑、结构建筑物building钢结构steel structure已有钢结构existing steel structure钢筋混凝土结构reinforced concrete construction 楼面floor平台platform (PF)地面ground level栏杆handrail楼梯stair; stair way直梯ladder柱column; post; stanchion基础foundation; footing粱beam斜撑；支撑bracing桁架；主粱girder构件member隔墙partition wall墙wall。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Plumbing 管道包括所有的供水污水排水Trench 地槽Foul water [faʊl] 废水，粪水，总称Drain 排水管总称Waste pipe 污水管Soil pipe 粪水管Main Discharge stack 主排水管道(竖管) Branch discharge stack支排水管道(横管) Rainwater pipe 雨水管Dilator 扩张器coupling sleeve 连接套筒slippage 滑移collar 箍环manifold 英['mænɪfəʊld] 歧管Bypasses 旁通Interception 拦截lever handle 杆式手柄handwheel 手轮inside screw 内螺纹male connection 外螺纹连接butterfly valve 蝴蝶阀lever 英['liːvə] 杠杆，控制杆，手柄retainer valve 压力保持阀bronze clapper 青铜瓣（止回阀用）water hammer 水锤check valves disc 止回阀阀瓣threaded bolt螺纹栓calibration valve 校准阀stop cock 龙头control gauge 仪表控制half shell pressure vessel 瓦片式压力容器mantle 英['mænt(ə)l] 覆盖物; 幕; 罩hydrostatic pressure 静水压力泵类suction manifold吸入支管；进气岐管；discharge manifoldjockey pump 管道补压泵hydraulic component 液压组件in series 串联in parallel ['pærəlel] 并联star-delta switch 星型三角开关clamping bracket 夹紧托架Gully trap 连接stack和pipe Eave Gutter ['gʌtə] 天沟Faucet ['fɔːsɪt] 水龙头Tap 水龙头Spray faucet喷水龙头Soak away ['səʊkəweɪ] 渗水坑cesspool ['sespu:l] 污水池septic tank ['septɪk] 化粪池Bracket 将管道固定在墙体的夹具Plumbing reservation 管道预埋Vent 排气管Main Stack 竖管Branch stack横管Clean-out 检修口Access point 检修口Trap 存水弯Flushing pipe 冲水管道DOMESTIC WATER SUPPLY 生活用水Tee 三通Pipe fitting 管件Junction 接头Pipe Shaft 管道井patio['pætɪəʊ] 露台；天井Polypropylene pipes (PPR) 聚丙烯管Fuel 燃料Black steel pipes 黑钢管Seamless 无缝Insulation and Lagging 隔热和保温Gate Valve 闸阀Float Valve 浮阀Check Valve 止回阀Water Stop Flange[flændʒ] 止水法兰Automatic Air Vent 自动跑风门Strainer 过滤器Panel board 配电盘Pad衬垫Cylindrical Water Tank 圆柱形水箱Overflow 溢流管isolating valve 隔离阀drain valve 排水阀Fuel Tank 燃料箱filling line pipe 灌装线管道Electric Water Heater 电热水器Thermostat['θə:məustæt]恒温器pressure relief valve 泄压阀Shaft 井Drainage['dreinidʒ] 排水The removal of excess surface water or groundwater from land by means of surface or subsurface drainsTrench drain 排水沟Manhole 检修孔，观察井（大的）Inspection chamber观察井(小的)ductile iron 球墨宙铁Sump pit 污水坑Sump pump污水泵submersible[səb'mə:səbl] pump 潜水泵sewage ['sju:idʒ] 污水SANITARY['sænitəri] FIXTURES 洁具Sanitary appliance 卫生器具Angle valve 角阀Waste outlet trap 废物排出阱Water closet['klɔzit]坐便器Bidet ['bi:dei]洗浴坐便器Lavatory ['lævətəri, -,tɔ:ri] 洗手池Bathtub['bɑ:θtʌb]浴缸siphon ['saifən] trap 虹吸阱；虹吸封气；[建] 虹吸式存水弯Bathtub handleBasin ['beisən] 洗手盆vanity basin 洗脸盆handrinse basin 洗手盆towel rail n. 手巾架urinal ['juərinəl] 小便器extraction valve 抽气阀extractor 抽气机卫浴产品vitreous china 玻璃瓷enamel [ɪ'næm(ə)l] coating 搪瓷涂层enamel 瓷釉feldspar 长石limestone 石灰石空调安装Refrigerant[rɪ'frɪdʒ(ə)r(ə)nt] 制冷剂inverter system 变频器heat dissipation 散热cooling capacity 制冷量Multi-unit多联机组。
One drag three 一拖三组合式空调机组modular air conditioning units模块化冷水机组modular cold water unitsfresh air unit 新风机组split air-conditioning unit分体空调机组air-cooling cold water unit 风冷冷水机组Cooling mode 制冷模式Chiller 空调主机Diffuser 风口Fan coil 风机盘管Brass 铜管supports and hangers 支架，吊架shipping skid 运输托架safety barricade 安全路障tamper proof latch[lætʃ]防盗门栓tamper proof 干预防护（防止接近有危险的主机）storage tank 蓄水或储油罐子shipping weight装运重量（）也叫装船重量purge valve 放气阀stud 双头螺栓liquid flashing 液体闪蒸inverted trapaccess valve 入口阀，清洗用pulsation 震动ESEER 季节能效比(Seasonal Energy Efficiency Ratio) reciprocating compressor 往复式压缩机；[机] 活塞式压缩机分体拖一至拖三主机Split drag one to drag three chiller铜弯头Copper elbow三通tee变径reducercabinet['kæbɪnɪt] 柜子power supply cabinet电源控制柜Flame retardant hose阻燃软管Ventilation [,venti'leiʃən]通风Exhaust Air Louver ['lu:və]排气百叶窗Exhaust register 排气调节器Supply Diffuser 供风分布口Return Diffuser 回风分布口vibration isolator 隔振器Duct Work 风管工程Volume damper 风量调节阀Non Return damper 止回阀Fire Damper 防火阀Motorized Smoke Damper 电动排烟风门Motorized Damper 电动风门Duct lining 风道衬里Condenser 冷凝器Compressor 压缩机Absorbed power 吸收功率capillary soldering or brazing 钎焊连接flux 助焊剂solder 焊料FIRE FIGHTING 消防Fire hydrant 消防栓Automatic Air Vent 自动跑风门Portable fire extinguisher 便携式消防灭火器strobe light 频闪灯Landing Valve 起落阀Zone Control Valve 区控制阀门Alarm Check Valve 警报单向阀Siamese connection 消防水泵接合器Sprinkler ['spriŋklə]喷头（upright正立，pendant吊坠, sidewall侧墙）Testing and Commissioning 测试和调试fire hydrants 消防栓hose 软管spear 喷枪wrench 扳手jockey pump 管道补压泵portable fire extinguisher 便携式灭火器route 路线drainage point 排流点male connection 外螺纹连接lance 喷枪pillar fire hydrant 立柱消防栓spout 喷口male plug 插头fire engine 消防车hose reel 软管卷盘hydrostatic testing 液压测试sparklet ['spɑrklɪt]发泡粉Deflector 转向器Stem 阀杆风管Kraft paper牛皮纸Rock wool 岩棉galvanised steel mesh 镀锌钢网pulley 皮带轮belt 皮带impeller [ɪm'pɛlɚ] 叶轮，推动器ball bearing 球轴承squirrel cage 鼠笼型collar type flange 轴环型法兰relief type flange 溢流型法兰non-ferrous 有色金属inspection tunnel 检查隧洞gallery 英['gæl(ə)rɪ] 廊道fire compartment 隔火间tapered ['tepɚd] fitting 锥形配件three-way cock 三通旋塞。