Safety poster 简体操作手册
新颖水漏防护系统用户手册说明书
| MSDS | DoP |PRODUCT CODE: HB-2SIZE & PACKAGINGNewton 403 HydroBond is supplied in rolls of 1.0m x 20.0m (20m2), packaged 20 rolls to a crate (400m2). Product weight is 1.235kg/m2.METHODS OF APPLICATIONNewton 403 HydroBond is placed to formwork ready for the placement of concrete. For concrete rafts and slabs, Newton 403 HydroBond is fitted above a sound and uniform support such as a concrete blinding or compacted hardcore.When installed to walls, Newton 403 HydroBond is fitted to sound and uniform permanent formwork such as existing walls or faced-off piles. Please see page 4 for a list of suitable support substrates. CONSTRUCTIONThe construction should conform with current Building Regulations, British Standards and relevant Codes of Practice. New concrete should be designed by a Structural Engineer to EN 1992 (Formally BS 8110 & BS 8007) to be structurally capable for the intended use as an earth retained structure, resisting loading from earth as well as water pressure as recommended within BS 8102:2009.NEWTON 108 HYDROBOND-LMWhere shuttering is to be removed to expose the outer face of the concrete walls, Newton 108 HydroBond-LM should be used to complete the 108 HydroBond System. 108 HydroBond-LM is a liquid rubber membrane that is spray applied to provide a continuous and seamless membrane to concrete walls, lapping over 403 HydroBond for a complete system. Newton 108 HydroBond-LM is very elastic, requires no primer and can be installed in cool and damp conditions ensuring that your project is finished on time and within budget. Up to 1000mday can be installed making 108 HydroBond-LM a very quick and cost efficient alternative to adhesive sheet membranes. Newton 109-LM is a derivative of 108 HydroBond-LM that can be applied by brush or roller where access for the spray machine is not possible, or for detailing.For further information on Newton 108 HydroBond-LM and our comprehensive range of waterproofingand damp proofing products and systems please contact our sales office on 01732 360095 or our website 12 Sweep the support surface clean, Substrate should be smooth and firm. Concrete surfaces should be freeof voids and sharp projections. Surface irregularities should be removed before installation. Voids mustbe filled with mortar, and holes filled with proprietarynon-shrink mortar/grout.34Measure the perimeter of the formwork to determinethe length of the membrane required. Make provisionfor 70mm overlaps to each end joint of the 20m long membrane rolls. When cutting the membrane use a retractable craft knife or sharp shears whilst wearing safety gloves.Fold along the guide created in the previous stage.Sharpen the crease with a hard roller.At internal corners, make a crease at the change in direction. Once the crease is formed, lift up the flap marked A and invert the upstand marked B so that the upstand of the flap A is in front of the main sheet upstand as shown in Fig. 7.Step one: Form a crease as shown. Stage 2: Fold back.Holding the membrane at point A of the grey flap and fold back so that your hand is at point C. The upstand B of figure 7 should now be against the formwork at point B. At this stage only the white fleece should be facing upwards.Seal the 45 degree joint with the double sided HydroBond tape. Use a hard roller to ensure a firm bond of the tape to the between the two surfaces of 403 HydroBond.5678910AABBCB Fig. 9 shows the completed corner. At this stage only the white fleece should be seen. The fold is to theright hand side of the joint and the membrane is triple thickness.For external corners, cut a square of 403 HydroBond and from a corner of that square, cut out a small square of about 75mm x 75mm. Fit the square to the corner and when in place, tape the square under the 403 HydroBond already in place.Seal the joints with HydroBond Tape. Over tape the corner with two patches of Newton Mesh Tape.Once all the perimeter of the substrate has been completed, ensure that all edges of the membrane above the floor support have either an adhesive edge or have been prepared with the doublesided HydroBond Tape. Unroll strips of membrane, overlapping the 403 HydroBond that is already in place by 70mm.To complete the overlapped joints, remove 75mmof the clear film to the underside (grey side) of the 403 HydroBond. Peel off the protective release liner from the adhesive edge of the HydroBond Tape and press the laps together. Use a hard roller to ensure the laps are fully and constantly adhered.All joints should be adhered with either the adhesive edge or the double sided HydroBond Tape. To reinforce the joints, over tape with Newton Mesh Tape using a hard roller and a Hot Air Gun to ensure the butyl underside of the Mesh Tape is fully bonded into the upper fleece of the 403 HydroBond.1113141516Nail the 403 HydroBond to the formwork leaving the nails exposed to give a key for the concrete and to ensure that the formwork can be easily removed. The nails are cut flush with the membrane after the formwork is removed. A dab of 106 FlexProof or 109-LM can be used over the small hole, although the membrane will self-heal.12UNDULATING WALL PERMANENT FORMWORKIf not faced-off, on contiguous piling, ensure that soil columns between piles are cut back to no less than one third of the pile diameter, to create a fixing cleavage, and reduce the likelihood of soil dislodging behind the membrane.Use shot fired nails to install the membrane so that it is tightly fitted into the undulations of the formwork. Ensure that the 403 HydroBond is fully supported by the formwork. Pay particular attention to the joints which should be fully adhered by either the adhesive edge or the double sided HydroBond Tape.INSTALLATION ABOVE FLOOR SUPPORTTo faced-off formwork, install as instructed within page 4 to page 6. Use HydroBond Tape or the adhesive edge to make the final seal between the upturned 403 HydroBond to that already installed to the walls.To undulating wall formwork, cut the 403 HydroBond into 500mm wide strips to the measure of the perimeter, plus 70mm end overlaps, plus a small error margin. Fold to make a 250mm upstand. To force the upstand to the shape of the piles you will need to cut and splay the fold above the floor support to allow it to lay flat. Once the The adjacent drawings show examples of facing off secant and sheet piling ready for the application of Newton 403 HydroBond.For further information on these drawings or for the facing off of other irregular substrate, please contact our technical department on 01732 360095.Pipe Protrusion Movement jointInterface with Pile Interface with Small PileNewton 104Newton 403 HydroBond HydroBond TapeNewton 106 FlexProof-X1 Newton 106 FlexProof-NV Newton 307 PipeSealNewton Waterproofing Systems Is A Trading Name OfJohn Newton & Company Ltd.Newton House, 17-19 Sovereign WayTonbridge, Kent TN9 1RH T: +44 (0)1732 360095E: ***************************.uk W:MEMBRANE REPAIRInspect the membrane before installation of reinforcement steel, formwork and final placement of concrete. The membrane can be easily cleaned by brushing or jet washing if required.Repair damage by ensuring the area is clean and dry and free from dust. Repair small punctures (12mm or less) and cuts by applying a patch of Newton 403 HydroBond (clear film removed from polymer side) centred over the damaged area and secure with HydroBond Tape, pressing firmly using a hard roller to ensure a good bond. Over seal the outer edge of the patch with Newton Mesh Tape. Use a hard roller and a heat gun to fully adhere the Mesh Tape into the HydroBond fleece.Repair holes and large punctures by applying a patch of Newton 403 HydroBond membrane, which extends 150mm beyond the damaged area. Seal all edges of the patch with HydroBond Tape (clear film removed from 75mm from the edge of the patch on the polymer side), pressing firmly using a hard roller to ensure a good bond. Over seal the outer edge of the patch with Newton Mesh Tape. Use a hard roller and a heat gun to fully adhere the Mesh Tape into the membrane fleece.Where exposed adhesive edges have lost adhesion or laps have not been fully sealed, ensure the area is clean and dry and reseal with HydroBond Tape, resealing the lap and rolling firmly with a hard roller. Over tape with Newton Mesh Tape.Make a 403 HydroBond patch of correct size and seal Over seal edges of the lap with Newton Mesh Tape with HydroBond tapeLIMITATIONSHorizontal installation surfaces should be free of excessive standing water, particularly where concreteunder blinding is not utilised. Newton 403 HydroBond can be installed in most inclement weather conditions,providing the quality/accuracy of the installation is not affected e.g. 403 HydroBond floating, hydrophilic waterbars submersed, etc. 403 HydroBond is not designed for unconfined above-ground waterproofing applications.403 HydroBond is engineered for use under reinforced structural concrete rafts or slabs of 150mm thick orgreater. Do not install 403 HydroBond in horizontal split-slab, plaza deck and roof applications that will receive a poured concrete wear surface or other solid topping.。
启动前安全检查(PSSR)管理程序
启动前安全检查（PSSR）管理程序目录1 目的 (1)2 范围 (1)3 术语定义 (1)3.1 启动前安全检查(Pre-Startup Safety Review) (1)3.2 工程尾项A\B\C (1)3.3 人机工程 (1)3.4 工艺安全信息(PSI) (1)3.5 工艺危害分析（PHA） (1)3.6 偏离管理 (2)3.7 系统单试 (2)3.8 启动负责人 (2)4 进行PSSR的时机 (2)5 原则 (2)6 内容 (3)6.1 工作流程 (3)6.2 启动前安全检查(PSSR)组长确定 (4)6.3 确认PSSR工作任务及范围 (5)6.4 启动前安全检查(PSSR)小组 (5)6.5 准备 (5)6.6 检查内容 (6)6.7 检查 (7)6.8 检查汇总 (7)6.9 报告 (7)6.10跟踪 (8)6.11文件整理 (8)6.12偏离管理 (8)6.13培训和沟通 (8)7 审计要求 (8)1目的为确保项目所有装置、设备、设施能够顺利、安全投入使用，特制定本程序。
2范围本程序适用于公司所有项目中以下装置、设备和设施：（1）新、改、扩建的装置、设备、设施（2）变更的装置、设备、设施（3）检修后的装置、设备、设施（4）发生过意外事故后的装置、设备、设施（5）闲置封存的装置、设备、设施3术语定义3.1启动前安全检查(Pre-Startup Safety Review)在装置、设备、设施启动前对所有工艺安全要素进行核查确认，判定是否能安全启动，并跟踪验证的活动。
简称PSSR。
3.2工程尾项A\B\C具体参见《项目移交试车安全管理程序》中的规定。
3.3人机工程是指使工作人员与设备、作业工具安全而有效地结合，环境更适合于人员作业，人机界面达到最佳匹配的系统工程。
3.4工艺安全信息(PSI)是指关于物料的危害性（包括原料、中间产品、成品、废料、添加剂、阻垢剂、缓蚀剂、润滑剂等等）、工艺设计基础（工艺的描述，包括工艺化学、材料、能量平衡、工序、工艺参数、工艺参数的限值及超出限值的后果等等）和设备设计基础（设备的设计所依据的假设条件和逻辑—包括工程数据、工程图、工艺和设备能力计算、设备规格、厂商的蓝图等等）的完整、准确的书面信息资料。
KYT手册
训
方式：危险点照片的情景分析
练
推进方法 ： ⑴ ＫＹＴ 试点期
ＫＹＴ
定 期 训
▲目标：根据 ＫＹ 基本方法，挖掘作业场所危险 方式：自己作业场所的分析
⑵ ＫＹＴ 展开期
练
作
业 前
▲目标：根据 ＫＹ 基本方法，作业分析 ／ 确认
⑶自主管理期
方式：设备保全 ／ 危险作业前的分析
ＫＹ
２． 基本方法 ： ——选定图片或以工作中的某个情景，领导介绍内容 ， 大家分析
题目 ： 叉车作业
２Ｒ １． 因物品堆放过高 ， 会挡住视线造成车祸
危 ２． 因未戴安全帽 ， 会被部品砸伤
⑴合并为 １－２ 项（按照带标记的项目是重点实施项目）；
４Ｒ
⑵设定团队行动目标；
⑶用手指着喊两遍
领导——喊一遍“…（ 干 ） 好！ …（ 干 ） 好”
全员——喊两遍
11
K iken Yochi Training 山东太阳纸业股份有限公司
SUNPAPER KYT危险预知训练培训
二二 ．． 什 什么么是是 ＫＫＹＹＴＴ
ＫＹＴ
１． 释义——全称危险预知活动，是针对生产特点 和作业全过程，以危险因素为对象，以作业班组为团队 开展的一项安全教育和训练活动，它是一种群众性的“自 主管理”活动，目的是控制作业过程中的危险，预测和 预防可能出现的事故。
训练（Ｔｒａｉｎｉｎｇ） 训练有素 预知（Ｙｏｃｈｉ） 预先掌握 危险（Ｋｉｋｅｎ） 不安全的状态
Ｈｉｄｄｅｎ Ｄｅｆｅｃｔｓ 潜在的问题
SUNPAPER KYT危险预知训练培训
任何一件事情，如果客观存在着发生某种事故的可能性，不管这个可能性有多小， 如果重复去做时，事故总会在某一时刻发生。
春节安全宣传海报英语版
春节安全宣传海报英语版Spring Festival Safety Publicity Poster (English Version) Title: Celebrate Spring Festival SafelySubtitle: Ensuring a Joyful and Secure Spring Festival for Everyone1. Top Section:- A vibrant image representing the festive atmosphere of the Spring Festival.- Text: "Welcome to the Year of [current year]."2. Middle Section:- Image 1: A family enjoying a traditional reunion dinner.- Text: "Importance of Family Reunion"Explanation: The Spring Festival is a time for families to come together and celebrate. Emphasize the significance of cherishing this time with loved ones.- Image 2: Fireworks display.- Text: "Fireworks Safety"Explanation: Highlight the potential hazards of fireworks and promote safe practices, such as attending organized fireworks displays and keeping a safe distance.- Image 3: Red envelope or money bag.- Text: "Financial Security"Explanation: Remind people to be cautious with their financial transactions during the festival, such as avoiding scams and securing their belongings.3. Bottom Section:- Image 4: Traffic scene with various means of transportation.- Text: "Travel Safety"Explanation: Promote safe travel practices, including following traffic rules, not drinking and driving, and wearing seatbelts.- Image 5: A clean and organized home.- Text: "Home Safety"Explanation: Encourage people to take precautions to prevent accidents at home, such as checking electrical appliances, installing smoke detectors, and keeping fire extinguishers handy.- Image 6: A healthy meal with fruits and vegetables.- Text: "Food Safety"Explanation: Educate on the importance of food safety during festive gatherings, including proper storage, cooking, and avoiding expired or contaminated food.4. Footer:- Important contact information for emergency services and helplines.- Text: "Emergency Contacts"Explanation: Provide relevant emergency contact numbers for fire, police, medical services, and helplines for immediate assistance.Note: The above suggestions are provided for reference only. The final design and content should be tailored to the specific needs and target audience of the Spring Festival safety campaign.。
AIS自动安全识别系统操作说明(中文)
AIS自动安全识别系统FA-100使用说明一、操作说明1.3调节显示器亮度和对比度1.同时按[CLR/ALM]+[SFT/+/-]键2.用[ ▲]或[▼]键调节亮度;用[ ◢]或[ ◣]调节对比度3.按[ENT]键关闭窗口.1.4 菜单介绍1.4.1菜单操作过程1.按[MENU]键显示主菜单2.按相应数字键进入子菜单,例如按[ 6 ]进入SYSTEM SETTING子菜单.(也可以按[ NEXT ] 选择,按[ ENT ] 键进入.3.继续按数字键进入下一级菜单,例如,按[ 5 ]进入SET BUZZER子菜单.4.按[ ENT ] 键保存.5.按[ MENU ]返回主菜单.1.4.2 注意事项确认输入如果修改数据后,未按[ ENT ] 而直接按[ MENU ] 会出现提示按YES 不保存退出,如果要保存,选NO ,按[ ENT ],再按[ ENT ] 保存.选择数据输入格式1.5 航行设置航行开始前, INIT SETTINGS 菜单中有5项数据要输入: draught 吃水destinatuon 目的地navigation status 航行状态ship type 船型number of crew 成员数1.按[ MENU ] 打开主菜单2.按[ 5 ] 打开INIT SETTINGS 菜单3.按[ 1 ] 选择SET SHIP DATA4.选择DRUGHT (吃水)5.按数字键输入本次航行的准确吃水。
（航行中吃水变化要进行修正）6.按[ ENT ] 确认后返回INIT SETINGS 菜单7.按[ 2 ] 选择SET DESTINATION8.选择DATA ,输入预计到达目的地的日.月,按NEXT 选择TIME9.输入预计到达目的地的时间,按NEXT 选择DESTINATION10.输入目的地的名称,按[ ENT ] 保存后返回INIT SETTINGS 菜单11.按[ 3 ] 选择SET NA V STATUS12. 用[▲] [ ▼] [◢] [ ◣] 在列表中选择相应的航行状态。
Safety-M 安全模块 操作手册说明书
operating manualforSafety-M modulesoperating manual (Vers. 1.-19.12.2007)Important advicetarget audience of this operating manual:maintaineance, replacement, electricians, usersDefinitionsThe synonym Safety-M is used as generic term for all derivates of the Safety-M product line. If the manual points directly to a certain derivate, though the entire term will be used (i.e. Safety-MS2).The following term …safe“ is used for safe function according to the EN 954-1 respectively according to EN 61508 in the particular category or level. Safety Adviceoperating and serviceBefore installation and demounting, or the disconnecting of signal- and power supply cables, the modules has to be de-energized.It has to be avoided to get electrostatics at the terminal blocks and connectors during the dismounting of the Safety-M modules.Guarantee and safety approval is void, if the modules has been manipulated.The Safety-M can only be operated in a temperature range between 0° and 50° C. Make sure that this temperature range will not exceeded.Checking the Certification Code (CRC)Before the normal operation of Safety-M at a machine or plant a safety audit has to be proceeded. As result a test report has to be existent. This report contains a certification code. This code assures that a Safety-M module will be operated with the correct program. By pressing the key “Function” in the normal operation mode …RUN“ (see underneath), the certification code is shown in the 7 – segment display. Compare these displayed numbers (i.e. C 56124) with the numbers of the test report of this particular machine or plant, that they are matching. If these numbers are different, the normal safe operation is not assured. In this case you have to stop the machine or plant at once and contact the company, who installed this machine.modification of an installationThe commissioning or changing of an installation of Safety-M can only achieved by qualified personal! Contact the company, who did the safety related test report. By changing the configuration the safety function of the module can be lost.programming interface7 segment display terminal blocks for input / output signalsLED´s show operating modefunction key for reset and CRC (test report code) encoder interfaceStart up sequencesAfter a start up is initiated, the particular start up phases are shown in the display. If no errors are occurring, the following phases will be passed.7 segment display mode description…1“ STARTUP synchronization, check of configuration- /firmware data…2“ SENDCONFIG synchronization, check of configuration- /firmware data zone check…3“ STARTUPBUSactivate bussystem…4“ RUN normal operating status…5“ STOP only for authorized personal available…A“ ALARM alarm can be reset by pressing the …Function“ key…F“FAILURE Failure can be reset by switching the Safety-M (power supply) OFF and ONLEDcolor mode descriptiongreen …blinking“ system OKyellow …blinking“ get in touch with authorized personalred …blinking“ alarmred …continious“ Fatal Error – Safety-M power supply must be disconnectednotice:Only the operating status 4 = RUN allows after a correct installation of the Safety-M to operate the machine or plant. All configurated safety functions are active. If the Safety-M is in the mode “alarm” = A or in the mode “failure” = F all safety related outputs are deactivated.modification / procedures with changes at the modules or installationrepairRepair of a module could only be achieved in the manufacturer.guaranteeBy changing the Safety-M layout or opening the enclosure the guarantee and safety approval is lost.mechanical modificationThrough modification of drives / mechanical transmission or changing the sensors (encoders) the safety function could be lost. Talk to the company who has installed or delivered the Safety-M modules, or to the person who has created the safety test report.electrical modificationThrough modification the cabling or wiring of the Safety-M modules the safety function could be lost. Talk to the company who has installed or delivered the Safety-M modules, or to the person who has created the safety test report. MaintaineanceExchange of a Safety-M modulAfter a Safety-M module has been changed it has to be assured, that the spare module contains the same configuration. The test report code (check sum / CRC) can be shown in the 7 segment display. It has to be sure, that the these numbers are the same in the test report.Follow the instructions by changing a Safety-M modul•disconnect the drive from the power supply•switch of the power supply of the Safety-M and disconnect ale cables and connections•loosen the connectors of the sensors and pull off•disconnect all further connections•get the Safety-M from the (DIN) rail and pack the Safety-M according to EMC prescriptions•install the new Safety-M at the (DIN) rail•rebuild all connections•switch on the drive•switch on the power supplynote:Basically no pluggable connection of the Safety-M can be disconnected or connected during the voltage is on. Especially the connected speed and position sensors (encoders) could be destroyed.failure modes of the Safety-MIn principle the Safety-M got two different failures according to the followingrelations:failure mode descriptionresult for thesystemreset conditionFatal Errorfatal exceptional error in theinternal program of the Safety-M.A cyclic program flow is not morepossible. The last active processis to operate the segment displayby system A. System B hasstopped.All outputs will bedisconnected - shutdown!Only resettable byswitching off thepower supply ofthe Safety-M(POR).Alarm functional failure, caused by aninternal process. Both systemswill still run in the cyclic processand handle all requirements ofthe communication interfaces.All outputs will bedisconnected - shutdown!Reset by the pre –defined reset inputIf an alarm or fatal error occurs more often, then contact the company who has installed the machine or plant.。
使用指南1：重要安全指示说明书
User GuideIMPORTANT SAFETY INSTRUCTIONS The device has been tested for conformance to safetyregulations and requirements,and has been certified forinternational use.However,like all electronic equipment,thedevice should be used with care.Please read and follow thesafety instructions to protect yourself from possible injury and tominimize the risk of damage to the unit.Please do not place the display screen towards the ground to avoid scratching the LCD surface.Please avoid heavy impact.Please do not use chemical solutions to clean this product.Simply wipe with a clean soft cloth to maintain the brightness of the surface.Please do not block any vent hole.Please follow the instructions and trouble-shooting to adjust the product. Internal adjustments or repairs must be performed by a qualified technician.Please keep user guide for future reference.Please unplug the power and remove the battery if long-term no-use,or thunder weather.FEATURESSupport multiple signal inputs3G-SDI,HDMI,DVI and VGA.Multiple View Display supports quad view split from different input singles simultaneously.Ultra HD4K screens containing8.3million pixel(3840×2160),so the resolution is four times that of Full HD.3D LUT for Accurate Color Reproduction and Color space display (Native/Rec.709/User1~User3).Support to upload3D LUT table via USB port.Equip HDR function.Image flip offers great convenience for user’s user to place the monitor with various mounting methods under different ers can view the monitor normally no matter what mounting angles.Perfect size for both suitcase and rack mount.Wireless HDMI function for optional.YP-01191008Contents1.PRODUCT DESCRIPTION (3)2.SUN SHADE INSTALLATION (6)3.MENU SETTING (7)4.ACCESSORIES (20)5.PARAMETERS (21)6.TROUBLE SHOOTING (22)1.PRODUCT DESCRIPTIONFront1.Speaker2.SDISignal switch to SDI mode when light on.3.HDMI1~4Signal switch to HDMI mode when light on.4.DVISignal switch to DVI mode when light on.5.VGASignal switch to VGA mode when light on.6.MENUPress to enter menu.Press to enter option in the menu.7.◄Select option in the menu.Decrease the option value.Before enter the menu,single press to activate volume,press again to decrease the volume.8.►Select option in the menu.Increase the option value.Before enter the menu,single press to activate volume,press again to increase the volume.9.EXITBack or exit.10.F1~F4User definable buttonsDefault function options：F1：Color Space F2：Display ModeF3：Safety Marker F4：Aspect（functions can be customized by long keep pressing any one of the 4buttons）11．Power indicating light(green light:working).12．Earphone jackBack1.Handle(Only available for23.8”/28”)2.VESA75×75&VESA100×100mounting portB port4.TALLY port5.VGA input port6.DVI input port7.HDMI input port×4。
国庆节安全海报英语版手绘
国庆节安全海报英语版手绘National Day Safety PosterIntroduction:National Day, also known as the Independence Day or the National Holiday, is a significant holiday in our country. It symbolizes the unity and progress of our nation. As we celebrate this important day, it is important to prioritize safety to ensure that everyone can enjoy the festivities without any accidents or incidents. This safety poster aims to raise awareness about the various safety precautions that should be taken during National Day.Poster Design:The poster should have a vibrant and eye-catching design to capture people's attention. It should include illustrations, symbols, and brief captions to convey the safety messages effectively. The following are some important safety precautions that should be emphasized in the poster:1. Fireworks Safety:Fireworks are an integral part of the National Day celebrations, but they also pose significant risks. The poster should highlight the importance of handling fireworks with care, keeping a safe distance from them, and following the instructions provided. It should also encourage people to attend professional fireworks displays organized by authorities rather than setting off their own fireworks.2. Road Safety:National Day often involves parades, special events, and anincrease in traffic. The poster should emphasize the importance of road safety, such as wearing seat belts, obeying traffic rules, refraining from drunk driving, and avoiding distractions while driving. It should also remind pedestrians to use designated crosswalks and be cautious while crossing the streets.3. Food Safety:During National Day, many people engage in barbecues, picnics, and outdoor gatherings. The poster should emphasize the importance of food safety, including proper handling, cooking, and storage of food. It should also remind people to bring and drink plenty of water to prevent dehydration, especially during the hot weather.4. Crowd Safety:National Day celebrations often attract large crowds. The poster should encourage people to be mindful of their personal safety in crowded places. It should advise people to be aware of their surroundings, keep their belongings secure, and avoid overcrowded areas to prevent accidents and potential incidents. 5. Fire Safety:The poster should highlight the importance of fire safety, especially during crowded celebrations. It should remind people to be cautious while using fire, such as grills or candles, and to keep them away from flammable materials. It should also encourage people to report any fire or emergency immediately to the relevant authorities.Conclusion:The National Day safety poster serves as a reminder for everyone to prioritize safety during the celebrations. Its vibrant design and clear messages will help raise awareness and ensure a safe and enjoyable National Day for all. Remember, safety should always be our top priority, enabling us to celebrate our nation's achievements while protecting ourselves and our loved ones.。
国庆节安全海报英语
国庆节安全海报英语National Day Safety PosterNational Day is a time for celebration and unity, but it is also important to remember to stay safe during this festive period. Here are some tips to ensure a safe and enjoyable National Day:1. Traffic Safety- Observe traffic rules: Always obey traffic signs and signals, and use pedestrian crossings when crossing the road.- Be cautious on the roads: Watch out for reckless drivers and be mindful of motorcycles, bicycles, and pedestrians.- Plan your journey: Before heading out, check the traffic conditions and plan your route to avoid congested areas.- Do not drink and drive: If you consume alcohol, make sure to have a designated driver or use public transportation.2. Fire Safety- Handle fireworks responsibly: Fireworks are a common sight during National Day celebrations, but they can be dangerous if not handled properly. Follow the instructions provided and keep a safe distance from the fireworks.- Barbecue safety: If you plan on having a barbecue, keep a fire extinguisher nearby and never leave the grill unattended. Ensure that the grilling area is well-ventilated and away from any flammable materials.- Avoid unauthorized firecrackers: Only purchase fireworks from authorized vendors and avoid using illegal firecrackers, as they can cause serious injuries.3. Water Safety- Supervise children near water: If you are spending National Day by the beach or at a swimming pool, always keep an eye on children to prevent accidents or drowning.- Follow lifeguard instructions: If there are lifeguards on duty, follow their instructions and swim only in designated areas.- Never swim alone: Always swim with a buddy, as it ensures that there is someone who can offer help in case of an emergency.- Use flotation devices: If you are not a strong swimmer, wear a life jacket or use other flotation devices.4. Food Safety- Practice good hygiene: Wash your hands before handling food and ensure that food preparation areas are clean. Keep raw and cooked foods separate to prevent cross-contamination.- Cook food thoroughly: Avoid undercooked or raw seafood, meat, and poultry, as they can cause foodborne illnesses. Use a food thermometer to ensure that food is cooked to the appropriate temperature.- Store leftovers properly: After the feast, refrigerate leftovers promptly to prevent the growth of bacteria.5. Personal Safety- Stay vigilant: Be aware of your surroundings and report any suspicious activities to the authorities.- Keep your belongings secure: Avoid carrying large sums of cash or valuable items. Keep your bag close to your body and securely fastened.- Stay in well-lit areas: If you are out at night, stick to well-lit areas and avoid dark alleys or secluded places.Remember, safety should always be a priority, even during moments of celebration. By following these safety tips, you can ensure a memorable and accident-free National Day. Enjoy the festivities and have a happy National Day!Note: The word count provided includes both the text in the poster and the additional information provided. The actual word count for the text in the poster alone is approximately 380 words.。
小学安全教育英文海报
---[Top Left Corner]Safety Awareness Campaign for Primary School Students[Center]"Safe Habits, Bright Future"---[Background]The poster is designed with a vibrant, playful background that incorporates elements of safety and learning. There are images of children in school uniforms, traffic signs, first aid kits, and a map of the school campus.---[Main Section]1. Fire SafetyBe Aware, Be Prepared!- Image: A child wearing a fire helmet and holding a fire extinguisher.- Text: "In case of a fire, don't panic. Use a fire extinguisher oralert the nearest adult. Always know the nearest exits and practice fire drills regularly."2. Road Safety♂️ Stay Safe on the Streets!- Image: A child wearing a reflective vest crossing the road with a pedestrian crossing sign.- Text: "Always cross the street at designated crossings. Wear bright clothes or a reflective vest in the dark. Listen to traffic signals and be aware of your surroundings."3. Water SafetySwim Smart, Stay Safe!- Image: A child wearing swimming goggles in a pool.- Text: "Never swim alone. Always have an adult present. Learn basic swimming skills and never enter deep water without supervision."4. Personal SafetyProtect Yourself!- Image: A child practicing a 'stranger danger' stance.- Text: "Trust your instincts. If someone makes you feel uncomfortable, tell a trusted adult. Never share personal information with strangers."5. Healthy EatingEat Right, Feel Right!- Image: A child choosing healthy snacks.- Text: "Make healthy choices. Eat a balanced diet, drink plenty of water, and avoid too much sugar and processed food."6. Computer SafetyStay Safe Online!- Image: A child using a computer safely.- Text: "Never share personal information online. Use strong passwords and be cautious of phishing scams. Always ask for permission before downloading apps or games."7. First Aid Basics♂️ Be Prepared to Help!- Image: A child showing how to perform a basic first aid technique.- Text: "Learn basic first aid skills. Know how to stop bleeding, treat burns, and perform CPR. Always have a first aid kit handy."8. Environmental SafetyProtect Our Planet!- Image: A child planting a tree.- Text: "Recycle, reuse, and reduce waste. Conserve water and energy. Be kind to animals and protect our environment."---[Footer][Bottom Left Corner]School Safety Committee- Contact Information: "For more information, contact the School Safety Committee at [Email Address] or [Phone Number]."[Bottom Right Corner]Joint Effort of Teachers and Students- Logo: The school logo alongside a heart symbolizing unity and care.---[Additional Notes]- The poster includes a "Safety Tips" section with a checklist for students to follow.- A "Remember This!" quote at the bottom: "Safety is a journey, not a destination. Take care of yourself and others every day."---[Closing]Safety First: A Secure Journey Through LifeThis poster is designed to remind all primary school students of the importance of safety in their daily lives. By promoting awareness and education, we hope to create a safer and more informed generation.---[Length]This poster encompasses approximately 1500 words, including images and text, providing a comprehensive guide to safety for young students.。
道路安全海报英文版
Road Safety PosterIntroductionRoad safety is of utmost importance for everyone, be it pedestrians or motorists. To spread awareness about road safety, a road safety poster can be an effective tool. This article aims to discuss the significance of road safety, the elements of an effective road safety poster, and some important tips for creating one.The Importance of Road SafetyEnsuring road safety is essential to prevent accidents, injuries, and fatalities. Here are some reasons highlighting the significance of road safety:1.Reducing Accidents: Road safety measures such as obeying trafficrules, wearing seat belts, and avoiding drunk driving cansignificantly reduce the number of accidents on the roads.2.Protecting Lives: Road accidents often result in severe injuriesand loss of life. By promoting road safety, we can protect lives and prevent families from experiencing the devastatingconsequences of accidents.3.Economic Impact: Road accidents have a considerable economicimpact, leading to medical expenses, property damage, and loss of productivity. Road safety measures can help reduce these economic burdens.Elements of an Effective Road Safety PosterCreating an impactful road safety poster requires careful consideration of various elements. Here are a few essential elements that should be present:1. Eye-Catching DesignA road safety poster should have a visually appealing design to grab attention. Colors, images, and typography should be carefully selected and coordinated to make the poster visually attractive and engaging.2. Clear MessageThe message conveyed by the road safety poster should be clear and concise. It should highlight the importance of road safety and urge viewers to take necessary precautions to ensure their safety and the safety of others.3. Use of VisualsIncorporating relevant visuals such as illustrations or photographs can effectively convey the message. Visuals can help create an emotional impact and make the message more memorable.4. Key InformationDisplaying key information such as emergency helpline numbers or important traffic rules can be helpful for viewers. This information should be provided in a legible and easily understandable format.5. Positive ReinforcementA positive and encouraging tone can be more effective in motivating people to adopt safe behavior on the roads. The poster should focus on the benefits of road safety and emphasize the positive outcomes of following traffic rules.Tips for Creating an Effective Road Safety PosterWhen creating a road safety poster, keep the following tips in mind:1. Research and PlanningBefore starting the design, conduct research to understand the target audience, their concerns, and the specific road safety issues prevalent in the area. Plan the message and visuals accordingly.2. Keep It SimpleAvoid cluttering the poster with excessive information or visuals. Keep the design clean and uncluttered, focusing on the main message and key information.3. Test for EffectivenessGet feedback from a diverse group of people to assess the effectiveness of the poster. This feedback can help identify any potential improvements or modifications to make the poster more impactful.4. Consider PlacementWhen displaying the posters, consider strategic placement in areas with high pedestrian or vehicular traffic. Ensure that the posters arevisible and easily readable from a distance.5. Regularly UpdateRoad safety campaigns should be ongoing efforts. Keep updating the poster design and message periodically to maintain interest and relevance.ConclusionRoad safety is a vital concern for everyone. By creating and displaying impactful road safety posters, we can raise awareness and promote safe behavior on the roads. Remember to focus on eye-catching design, clear messaging, relevant visuals, and important information while creating an effective road safety poster. Let’s work together to make our roads safer for everyone.。
LP外围热水器使用、安装和安全指南说明书
• T o the installer or person assembling this appliance: Leave this manual with this appliance for future reference.• T o consumer: Keep this manual for future reference. Thisinstruction manual contains important information necessary for the proper assembly and safe use of this product.Read a nd follow all warnings a nd i nstructions b efore assembling a nd u sing the appliance.Follow all warnings and instructions when using the appliance.DO NOT DISCARD THIS INSTRUCTION MANUAL.For outdoor use only.3985 N. 75 W. • Logan, UT 84321 • 1.800.650.2433 • Model HWD100711-HWD10-INSTRUCTIONSInstall and properly vent the water heater. Failure to properly install the water heater in this manual1. D o not leave this appliance unattended while in use. The user must remain in the immediatearea of the product and have aclear view of the product at all times during operation.2. K eep children and pets away from the burner at all times.3. T he use of alcohol, prescriptionor non-perscription drugs may impair your ability to properly assemble or safely operatethis appliance.4. F or OUTDOOR use only. Do NOT use in a building, garage or any other enclosed area. NEVER use this appliance as a heater.5. D o not operate appliance under ANY overhead construction. Keep a minimum clearance of 3 feet (1 m) from the sides, front and back of appliance to ANY construction. Keep the area clear of all combustable material and flammable liquids, including wood, dry plants, grass, brush, paper and canvas.6. K eep the fuel supply hose away from any heated surfaces.7. T o prevent accidental fires, before using the appliance check that the hose is not damaged and all joints and connections are not leaking by turning on the cylinder valve, and applying a soapy solutionto the joints and connections. Ifa continuous hissing sound is heard, or if the soapy solution bubbles, there is a leak. Do not use the appliance if there is a leak. Replace the faulty parts.8. E xtinguish all open flames before connecting the gas supply to the appliance and before checking for leaks.9. D o NOT move the appliance when in use. Allow unit to coolto 115°F (45°C) before movingor storing.10. I n case there is a fire, call thelocal fire department or dial 911.Stay clear from flames.11. T his product is not intended forcommercial use.12. S hould overheating occur or thegas supply fails to shut off turnoff the gas supply at the tank.ever operate this appliance unattended.ever operate this appliance13. D o not obstruct flow ofcombustion and ventilation to orfrom the appliance.14. T his appliance will be hot duringand after use. Use insulated ovenmitts or gloves for protectionfrom hot surfaces.15. A lways allow the appliance tocool before covering.16. A lways cover the appliance when notin use.Installation Safety Precautions • U se appliance only with LP (propane) gas and the regulator valve assembly supplied.• I nstallation must conform withlocal codes, or in their absence with National Fuel Gas Code, NFPA 54/ ANSI Z223.1. Handling and storageof LP cylinders must conform to LP Gas Code NFPA/ANSI 58.• D o not modify this appliance. Modifications will result in a safety hazard. Questions regarding certification in other areas may be addressed to 1-435-752-3922.• A partment Dwellers: Checkwith management to learn the requirements and fire codes forusing an LP Gas appliance at an apartment. If allowed, use outsideon the ground floor with a 3 foot clearance from walls or rails. DoNOT use appliance on or under any apartment, condominum balconyor deck.• B efore opening LP tank valve,check the coupling nut for tightness. When appliance is notin use, turn off LP tank valve on supply cylinder.• N ever use LP tank if visibly rusted, damaged, or out of date.• T he regulator may make ahumming or whistling noise during operation.• C lean and inspect the hose beforeeach use of the appliance. If thereis evidence of abrasion, wear, cutsor leaks, the hose must be replaced prior to the appliance being putinto operation. See product sheetfor hose & regulator information.• D o not block holes in bottom, top or sides of appliance.• N ever operate appliance with LP tanks out of correct position specified in assembly instructions.• A lways close LP tank valve and remove coupling nut before moving LP tank form specified operating position.• N EVER store a spare LP tank under or near appliance or in enclosed areas. NEVER fill the cylinder beyond 80% full.An overfilled spare LP tank is hazardous due to possiblegas released fromthe safety reliefvalve. Failureto follow theseinstructionsexactly couldcause a fire resulting in death or serious injury.• I f you see, smell, or hear escaping gas, immediately get away from the LP tank/ appliance and call your fire department. Combustion by-products produced wcontain chemicals known to WARNING: HOSE IS A TRIP HAZARD• A ll spare LP tanks must have safety caps installed on the LP tank outlet.LP Tank Removal, Transport and Storage• T urn OFF all LP tank valve. Turn coupling nut counterclockwise by hand only – do not use tools to disconnect. Install safety cap onto LP tank valve. Always use cap and strap supplied with valve. Failure to use safety cap as directed may result in serious personal injury and/or property damage.• A disconnected LP tank in storageor being transported must have a safety cap installed (as shown). Donot store an LP tank in enclosed spaces such as a carport garage, porch, covered patio or other building. Never leave an LP tank inside a vehicle, which maybecome overheated by the sun.• D o not store LP tanks in an area where children play.• S torage of an appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance.LP TankThe LP tank used with your appliance must meet the following requirements:• P urchase LP tanks only with these required measurements: 12”(30.5cm) (diameter) x 18” (45.7cm) (tall) with 20 lb. (9 kg.) capacity maximum.• L P tank must be constructedand marked in accordance with specifications for LP tank of theU.S. Department of Transportation (DOT) or the National Standardof Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes forthe Transportation of Dangerous Goods.• T he propane cylinder used with this appliance must include a collar toprotect the cylinder valve.LP tank valvemust have:• T ype 1 outletcompatible withregulator orappliance.• Safety relief valve.• U L listed Overfill Protection Device (OPD). This OPD safety feature is identified by a unique triangular hand wheel. Use only tanks equipped with this type of valve.LP tank must be arranged forvapor withdrawal.LP (Liquefied Petroleum Gas)• L P gas is non-toxic, odorless and colorless when produced. For Your Safety, LP gas has been given an odor (similar to rotten cabbage) so that it can be smelled.• L P gas is highly flammable andLP TANK FILLING• U se only licensed and experienced dealers.• L P dealer must purge tanks before filling.• D ealer should NEVER fill LP tank more than 80% of LP tank volume. Volumeof propane in tanks will vary by temperature.• A frosty regulator indicates gas overfill. Immediately close LP tank valve and call local LP gas dealer for assistance.• D o not release liquid propane (LP) gas into the atmosphere. This is a hazardous practice.• T o remove gas from LP tank, contact an LP dealer or call a local fire department for assistance. Check the telephone directory under “Gas companies” for nearest certified LP dealers.LP Tank Exchange• M any retailers that sell appliances offer you the option of replacing your emptyLP tanks through an exchange service.OPDHandWheelUse only those reputable exchange companies that inspect, precision fill, test and certify their cylinders. Exchange your tank only for an OPD safety feature-equipped tank as described in the “LP Tank” section of this manual.• A lways keep new and exchanged LP tanks in upright position during use, transit or storage.• L eak test new and exchanged LP tanks BEFORE connecting to appliance.LP Tank Leak Test For your Safety• L eak test must be repeated each time LP tank is exchanged or refilled.• D o not smoke during leak test.• D o not use an open flame to check for gas leaks.• A ppliance must be leak checked outdoors in well-ventilated area, away from ignition sources such as gas fired or electrical appliance away from open flames or sparks. Use a clean paintbrush and 50/50 soap and water solution. Use mild soap and water. Do not use household cleaning agents. Damage to gas train components can result. Brush soapy solution onto all weld seams and entire valve area.Setup Using Mounting Brackets This appliance must be mounted toa non-combustible surface. Mount toa non-combustible surface using the supplied hardware. For a temporary mount the unit may be suspended from the top bracket. If mounting permanently the appliance should be mounted using both the bottom and top tabs.Outlet Hose and ShowerHead AssemblyAttach the shower nozzle to the hose. Make sure toinsert the suppliedrubber gasket atthe connection.Connect theopposite end ofthe hose to thebrass fitting onthe bottom of theappliance labeledsure to insert thesupplied rubber gasket at this connection. Hand tighten only.(Optional Garden Hose Connector To Output)An additional brass fitting for connecting a standard garden hose to the outlet of the appliance is included. If connectinga garden hose to theoutput first connectthe brass fitting usingthe supplied gasketto the brass fittingon the bottom of theappliance labeled water output. Hand tighten only. Attach the garden hose to this connection. Make sure the garden hose has a rubber gasket inserted in the connector.Water SupplyInput AssemblyAttach standardIf “growing” bubbles appear,do not use or move the LP tank. Contact an LP gas supplier or yourRUBBER GASKET Hot exhaust gases exit from the top of the appliance. The unit should not be installed whereRUBBER GASKETgarden hose to the fitting on the bottom of the appliance labeled water input. Make sure to insert the supplied rubber gasket at the connection.Battery InstallationInstall 2 “D” cell batteries in thecompartment on the bottom of theappliance. Make sure the batteries areinstalled in the correct direction. Cleanthe battery contacts and also those of the device prior to battery installation.Always purchase the correct size andgrade of battery most suitable for theintended use.Do not mix new and used batteries.Replace all batteries at the same time.Instructions For ConnectingRegulator To Appliance• A ttach gas regulator to the appliance. The regulator will attach the brass fitting on the bottom of the appliance labeled Gas Input. Tighten the fittings using wrencheson both the brass adapter fitting on the appliance and the brass fitting on the end of the hose. • U se two adjustable wrenches or 3/4” and7/8” wrenches for tightening the hose to the brass valve of the appliance.Instructions For Connecting Regulator To The TankOnly use the pressure regulator & hose supplied with this appliance. Replace only with low pressure regulator model RA328.1. P lace LP tank on a secure,level, and stable surface.2. T urn off water supply to the appliance.3. T urn LP tank OFF by turning hand wheel clockwise to a full stop.4. R emove the protective cap from LP tank valve. Always use cap and strap supplied with valve. Do not use a POL transport plug (plastic part with external threads) It will defeat the safety feature of the valve.5. H old regulator, insert nipple (B) into LP tank valve. Hand tighten coupling nut,holding regulator in a straight line (C)with LP tank valve so as not to cross thread the connection.6. T urn the coupling nut clockwise totighten to a full solid stop. The regulator will seal on the back-check feature in LPtank valve, resulting in some resistance. An additional one-half to three quarters turn is required to completeconnection. Tighten by hand only – donot use tools.NOTE: If you cannot complete connection, disconnect regulator and repeat steps 5 and 6. If you are still unable to complete the connection, do not use this regulator!• D o not insert any foreign objects into the valve outlet. You may damage the valve(C) Holdcoupling nut and regulator as shown for proper connection to LP tank valve.(B) Nipple has to be centered into the LP tank valveAttempting to tighten the hosefitting to the appliance withoutusing a wrench on the brassand cause a leak. Leaking propane may result in explosion, fire, severe personal injury, or death.• N ever attempt to attach this appliance to the self-contained LP gas system of a camper or trailer or motor home.Instructions For Leak Testing 1. T urn off water supply to the heater.2. B e sure regulator is tightly connected to LP tank.3. C ompletely open LP tank valve byturning hand wheel counter clockwise. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. Correct before proceeding.4. B rush soapy solution onto indicated connections shown at right.5. I f “growing bubbles appear, there is a leak. Close LP tank valve immediately and retightenconnections. If leaks cannot be stopped,do not try to repair. Call for replacement parts. Order new parts by giving the serial number, model number and name of the items needed to the Service Center 1.435.752.3922.6. A lways close LP tank valve afterperforming tank leak test by turning hand wheel clockwise.o not use appliance until leak checked.f you cannot stop a gas leak, IF THE FLAME IS ACCIDENTALLY EXTINGUISHED TURN OFF THE FLOW OF THE WATER AND WAIT 5 MINUTES BEFORE RESUMING THE FLOW OF THE WATER.All cleaning and maintenance should only be done when the appliance is cool and with the fuel Hose Check •B efore each use, check to see if hoses are cut or worn. Replace damaged hose assembly before using appliance. Use only valve/ hose / regulator specified by manufacturer. See product sheet for hose & regulator information.This appliance is capable ofproducing s caution s hould Using The ApplianceThis appliance is equipped with a Hi/Low switch. This switch can be used to increase or decrease the heating capacity on the appliance. For colder incoming water temperature, switch should be set to Hi. For warmer temperatures, the switch should be set to Low. 1. T urn on the gas supply at the tank.(Open valve slowly.)2. T urn the water valve on the front of the appliance to high. Turn the heat valve on the front ofest m ust unit being connected to the water.the appliance to low. (This is the lowest temperature setting)3. T urn the water supply on. (If water flows through the shower hosethe appliance will ignite.) If wateris not flowing through the shower head the shower nozzle can be rotated to the desired setting.4. O nce water is flowing through the system the appliance will ignite. During ignition there will be aseries of audible clicks and then the burner will ignite. If the burner does not ignite after 5 seconds see the section on troubleshooting. Adjustthe temperature of the water by first increasing the heat valve. If a hotter temperature is desired decrease the water flow by adjusting the water valve.The temperature of the wateris dependent on the incoming water temperature and flow andCleaning and Maintenance Correct care and maintenance will keep your appliance operating smoothly. NOTE: Clean the entire appliance each year and tighten all hardware on a regular basis (1-2 times a year or more depending on usage).Using with a pumpIf using the appliance with a pump a minimum 3.5 GPM on demand diaghram pump is recommended. Any typical on demand RV pump should work. Most bilge pumps will not pump the necessary flow at the required pressure for the appliance to function properly.A minimum sustained pressure of 35psi is required.If the appliance is not working properly when attached to a pump try connecting the appliance to a pressurized water source (garden hose from house. If appliance works properly the pump being used is probably not adequate.Draining the systemThe appliance must be properly drained if exposed to freezing temperature. To drain first disconnect the water inletand the shower hose from the bottomof the appliance.Second removethe drain valvefrom the bottomof the waterheater. Failure toproperly drain theappliance will cause damage that may not be repairable. Damage due to freezing is not covered by the warranty.TroubleshootingUnit will not ignite (There are no audible clicks at start up)1. M ake sure batteries are installed correctly or replace old batteries with new one.2. A djust tabs inside of battery compartment to ensure circuit is complete.3. M ake sure there is an adequate supply of water flowing through the system. The appliance requires a minimum of 5 quarts of water per minute flowing through the system at a minimum pressure of 35 psi before it will ignite the burners.4. M ake sure that the water inlet is connected to the correct fitting. The water inlet should be connected to the fitting on the right side closest to thebattery compartment.5. A wire has become disconnected on the inside of the unit. Make sure the gasis OFF. Remove the two knobs from the front of the appliance. Remove 1 screw from the bottom of the water heater going through the tab on the front cover. This is the only screw you need to remove. Make sure that the wire terminals are connected to the top of the battery compartment and all other wires are connected. (Call Technical Support at 1.800.650.2433)6. D ebris may have entered into the water regulator. Reverse the flow of waterby connecting the water source tothe outlet of the water heater and run water in reverse through the system. This back flushing will remove the debris.Unit will not ignite(There are audible clicks at startup but the burner does not ignite)1. M ake sure propane tank is full and tank is turned on.2. M ake sure there is an adequate supply of water flowing through the system. The appliance requires a minimum of 5 quarts of water per minute flowing through the system at a minimum pressure of 35 psi before it will ignite the burners.3. C heck gas connections for leaksusing the soapy water test. If leaksare found make sure the problem is resolved before attempting to ignite the appliance. A gas leak will cause the regulator to reduce the gas flow. When turning on the LP gas tank open the valve very slowly.4. R emove regulator hose from fittingon appliance and ensure there isno obstruction in the fitting on the appliance.Unit ignites and then shuts off 1. M ake sure there is an adequate supply of water flowing through the system. The appliance requires a minimum of 5 quarts of water per minute flowingthrough the system at a minimum pressure of 35 psi before it will ignite the burners.2. E xcessive winds may blow the flame out.3. M ake sure propane tank is full and tank is turned on.4. T he ignition sensor may not be adjusted properly. These wiresare located directly above the burner. The wires should be bentat 90 degrees and approximately1/4” above the burner. Use a pairof pliers to bend the wires as needed.5. T he thermocouple on the heat exchanger may need adjusted. The thermocouple should be centered in the hole on the heat exchanger.6. T here may be a problem with the thermostat. Call customer serviceat 1.800.650.2433.The manufacturer warrants heater components (exceptpaint and finish) to be free from defect in materials andworkmanship for 1 year from the date of purchase. Allaccessories (included with shower or purchased separately)are warranted from defect in materials and workmanship for 90days from the original purchasing date. Within these periods,the manufacturer will replace or repair defective parts deemedunusable from its original intent by making available the partsthereof FOB 3985 N. 75 W. Logan, UT 84318.Product paint and finish is not warranted. The exterior finish ofthe product will wear down over time.Clean the unit after each use to maintain the finish and prolongthe life of your product.Warranty does not cover normal wear of parts or damage caused by misuse, abuse, overheating and alteration. Repairs or alterations made by anyone other than Camp Chef are not covered in this Warranty. Manufacturer will not be held liable for any losses due to neglectful operation. Furthermore, this Warranty does not cover damaged caused by natural disasters such as earthquakes, hurricanes, tornadoes, floods,lightning, fires,etc. Upon the expiration of this warranty all such liabilitywill terminate.No other warranties are expressed or implied.Keep all original sales receipts. Proof of purchase is required toobtain Warranty services. Prior written approval and a ReturnAuthorization Number must be obtained. Returned items willbe accepted for repair or replacement only. Returns must beshipped prepaid. Collect shipment or shipments without aReturn Authorization Number will not be accepted. To obtainWarranty services call 1.800.650.2433.*Warranty applies to the contiguous US states only.The Triton portable gaspowered water heater heats water in seconds Automatically ignites when water is turned on • E asy turn brass garden hose connector• F ully adjustable heat and waterflow• 4 settings shower head: off, mist, shower, and jet.• I ncludes regulator hose for bulk propane tank• Includes 8 feet/96” shower hose• Comes with garden hose adapter• 2.6 gallons per min.• A djustable water temp. Increase upto 80°F• Wallmount• 25 lbs• 13.5 x 8.5 x 31”• For outdoor use only• U ses 2 D batteries for ignition (not included)• 1 standard LP tank is good for approx. 7 hrs. of continuous use, depending on set temperatureMaximum Flow2.6 Gallons/Min (Raises water temperature 35°FMinimum Flow1.1 Gallon/Min (Raises water temperature 81°F0711-HWD10-Instructions。
安全说明与操作指南：DSF 1201-15001、DSF 1205-10005 滤芯说明书
The pressure filter with change-over valve, type DSF 1201-15001, DSF 1205-10005 are designed for filtration of operating fluids according to the technical parameters of the data sheets 2133, 2136 and 2134 (or in case of special design the corresponding data sheet). 1. Safety instructions - Prior to operating the filter, manual and maintenance instructions have to be read carefully. - Follow the instructions of this manual under any circumstances! - The manufacturer does not assume liability for any damage, which occurs due to disregarding these instructions. - If operations are carried out differently, the safety of the pressurized device can not be assured! - Operating conditions given in the data sheet, especially excess pressure, temperature range and operating fluid, have to be followed unconditionally. Variation of these parameters can cause damage to important pressure holding parts and sealing. Also take in consideration the compatibility of filter components with the operating fluid. - Under working conditions the filter housing is pressurized. Do not try to loosen or remove any part of the filter or the filter housing during operation. The operating fluid could escape at high pressure and high temperatures. This does not a pply for parts of the decompressed or the turned off side of the filter (see …Maintenance“). - Leaking operating fluid always bears the danger of injuries and burns! - Do not open the filter housing until you made sure it is not pressurized any more! - Touching parts of the filter may cause burning, depending on the operating temperature. - When exchanging the filter keep in mind that it might have operating temperature. Danger of burning! - Always wear safety goggles and gloves when working on the filter! - If you come into contact with the operating fluid please follow the instructions of the fluid manufacturer!! - Only use original spare parts. 2. InstallationThe filter is supplied and delivered ready to be installed. The fitting position of the filter is vertical. The filter has to be fitted with fastening screws in size and amount according to the corresponding fastening bore holes of the filter housings. The fitting of the filter has to be carried out in the way that the least possible transmission of tensible forces on the filter housing and the change-over valve is given. The connection of the pipework has to be made with flanges for pipework. Ensure upon assembling that - no dirt and no impurities of foreign fluids penetrate the filter - the connections for input and output are correctly connected to the pipe system - the pipe system is connected with the filter; as stress-free as possible - the extension to demount and the accessibility to the service elements is guaranteed Filter with electrical respectively electronical clogging indicators have to be installed according to the unit specific conditions and according to the technical parameters of the corresponding data sheets. 3. Commissioning Before commissioning the completeness of the filter (filter elements and seals) and the cleanness have to be controlled. Air bleeding of the controlled filter has to be carried out to the following instructions: - The positioning pin of the selector shaft has to be located in the middle position - Opening of the air-bleed screws or air-bleed connections (air-bleed connections according to data sheet 1651 and connection of suitable airbleeding tubes with coolecting pan for the flow out of the operating fluid - Connection of the unit volume flow (reduced volume flow; from 10 to 50 l/min) until bubble-free operating fluid flows out of both airbleeding tubes - Disconnection of the unit volume flow - Remove the airbleeding tubes and close the air-bleed bore holes or air-bleed connections (air-bleed connections according to data sheet 1651) - Connection to the required filter side at the positioning pin of the selector shaft (see instruction plate at filter) 4. Change of Elements The changing of the filter elements is necessary when raching the unit specific pressure difference respectively reaching the maximum pressure difference given by the clogging indicator. If there is no unit specific definition, the change of the elements should be done at a maximum of p 6 bar. This has to be carried out as follows: - Opening of the pressure balance valve - Switching over the positioning pin from the operating side through the other side - Closing the pressure balance valve - Connect the air-bleed and the drain plug of filter side to be maintained with suitable pipes and place a collecting pan for the operating fluid flowing out - Opening of the air-bleed and drain plugs of the filter side to be maintained until no more operating fluid flows out - Release of the screws of the lid of the filter side to be maintained and remove the filterlid - Remove the retaining plate for the filter elements (DSF 1201-15001)EDV 08/12 - Englisch+49 (0)6205 2094-0 +49 (0)6205 2094-40 phone fax Friedensstrasse 41, 68804 Altlussheim, Germany e-mail url**************************/filtration+49 (0)6205 2094-0 +49 (0)6205 2094-40 phone fax Friedensstrasse 41, 68804 Altlussheim, Germany e-mail url**************************/filtration。
ICHEM Safety Centre - 操作手册说明书
How process safety can apply outside the process industries -Taming the wildriver rapidsTrish KerinDirector, IChemE Safety CentreHazards 29May 2019, BirminghamThunder River Rapids Ride,Dreamworld, Gold Coast.Source: .auWhat is the IChemE Safety Centre? Current Operating and Industry PartnersCurrent supporting partners and collaboratorsThe Incident25th October 2016 pump failureWaterleveldroppedEmptyraftbecamestuckFollowingraft with6 peoplecollideswith itRaft withpeopleflips,fatallyinjuring 4Incident details Graphics from HeraldSunA model for process safety•Lack of training for operators –Informal at best, lasted 90 minutes –“showed me the front page of the manual and just flipped through it. I had to go through it myself. She said just sign off on it when you are happy”•Not trained on emergency stop –“don’t worry about it, you don’t need to use it”–“would have waited for the senior operator to tell her to hit the e stop”How effective and comprehensive is your facility training?Do your operators fully understand how to safely operate the facility?Do they understand the hazards of theequipment? Do they know what to do in the event of an emergency?–Timber slats–The pump–Low water–Emergency stop –Maintenance –SeatbeltsPhoto: Thunder River Rapids ride after theincident showing large gaps between slats.Source: .auPhoto: Infinity Falls Orlando,showing correct slats.Source: Intamin–Pumps had tripped out 3 times in days leading up to the incident and twice that day–Cause of tripping not investigated, just reset–Lack of indication that pumps had tripped•Low water–Known hazard–Water droppedwhen pumps tripped–No indication ofwater level otherthan scum line–Safety rateddetection and shutdown system wouldhave cost approx.USD2,200Photo: Thunder River Rapids ride showingwater line. Source: •Emergency stop–Recommendation tosimplify E-stop rejectedbased on risk beingacceptable–Poor location–Function unknown –senior operator“surprised” to knowone existed Photo: Sample control panelSource: •Maintenance–All maintenance spending was cut 7months prior–Maintainer stated he performedregular checks–Regulator stated ride was in“generally poor condition”–Ride shut annually for overhaul, butmaintenance planner said he never saw an engineer inspect it on 9 occasions he witnessed shutdown Photo: Thunder River Rapids ride after the incident. Source: .au•Seatbelts–In May 2017 a fatality occurred atDrayton Manor due to no seat beltsbeing installed–Thunder River Rapids had Velcroseatbelts that were very worn and didnot hold–Other rides have mechanical bucklesPhoto: CoventryTelegraph of DraytonManor Splash CanyonrideHow robust is your MoC process?How reliable is your equipment?Do your operators have the correctinstrumentation?Do they understand how to safely shut the plantdown?Do you have the right maintenance regimes and competent maintainers?Do you have suitable PPE?•Similar incident in 2001 where empty raft flipped•Investigation determined chance of repeat with passengers in “is nil”•Senior engineer believed the 2016 incident was caused by operators not following procedures•No emergency drills conducted before or since incidentHow thorough are your incident investigations?Is your system resilient to procedural deviation? Do you have regular emergency drills and evaluate their effectiveness for learnings?•Three years earlier recommended simplifying to one E-stop –not done •In 2016 ride given extension as could not find a competent person to inspect •Inspector approved ride weeks before incident without completing required checksHow thorough are your audits and inspections?How are recommendations managed and addressed?Are required regulatory audits or inspections carried out as required?stop set up–Two different stops available and no one appeared to understand how they worked •36 checks per minute to be performed by operator, from safety to customer service •Lack of understanding of human factors –“In my view if procedures are followed the system is a safe system, you may as well not open the park. Procedures are there to be followed, if we don't follow procedures in everyday life, things happen”How much load is being placed on your operators?Are your procedures simple to follow?Do you have engineered safety systems or are you relying on administrative controls only?•New rides prioritised over maintenance of existing rides•Culture of fear among operators •Lack of learning from incidents •No effective incident tracking system •Regarding safety “everyone thought it was someone else’s responsibility”How much focus is ageing plant getting versus new plant?Do people feel safe to report issues?How are learnings captured and shared?Who is accountable for safety in your facility?QuestionsPhoto: Floral tributes at Dreamworld entrance. Source: .auContact detailsTrish Kerin, CEng, FIChemE, FIEAust, Professional Process Safety Engineer, Director IChemE Safety Centre–Email ***********************–Phone +61 408 925 536––Twitter @TkerinTrish& @SafetyIChemE –LinkedInhttps:///in/trishkerinhttps://www.bit.ly/ISCLinkedIn。
自编IABP的使用手册
球囊的位置 (2)建立测压连接 (2)IABP的连接 (3)IABP的禁忌症： (4)IABP球囊的使用 (4)球囊规格 (4)IAB导管的插入部位准备 (10)准备IAP导管 (10)无鞘插入 (10)带鞘插入FOR SHEATH INSERTION (11)常规球囊导管的组成 (11)穿刺包盘 (12)压力监测设置PRESSURE MONITORING SET UP (12)如何拔出？ (13)反搏压不足如何处理？ (14)IABP的作用 (14)工作模式有三种 (14)快速启动的特性Rapid Start (14)系统设计 (15)屏幕显示 (15)操作方法 (15)故障排除Troubleshooting (16)1. 电子系统的报警 (16)2. 气动系统的报警 (17)触发报警可能原因及更正操作 (17)导管报警可能原因及更正操作 (19)3.警示（alert）信息 (23)警示信息原因及更正操作 (23)球囊反搏泵的脱机标准 (25)主动脉血压波形 (25)第 1 页共38 页2012-09-11反搏治疗时动脉波形变化 (26)正常的球囊压力波形 (27)时相错误- 充气过早 (30)时相错误- 充气过晚 (31)时相错误- 放气过早 (31)时相错误- 放气过晚 (31)使用IABP期间的护理 (35)IABP机器管理 (36)常见并发症护理 (36)球囊的位置球囊位于降主动脉内左锁骨下动脉远端。
X线下，在第2-3肋间隙水平。
建立测压连接第 2 页共38 页2012-09-11压力系统包括盐水袋、冲洗装置和压力传感器，有三个接头：加压盐水袋、IAB泵的动脉压力输入和压力延长管（不超过8ft.；引出主动脉内压力和冲洗IAB内腔；接入中心腔接头）IABP的连接第 3 页共38 页2012-09-11IABP的禁忌症：①主瓣关闭不全②主动脉病变③与动脉穿刺相关的其他禁忌症④下肢缺血⑤穿刺部位渗血⑥血小板减少⑦球囊导管不动导致血栓形成⑧球囊破损⑨感染IABP球囊的使用球囊规格25cc：身高<152cm34cc：152-163cm40cc：163-183cm50cc：>183cm第 4 页共38 页2012-09-11球囊的包装穿刺包（穿刺针【造影针】、J形钢丝、扩张器、三通、肝素帽、带止血阀和扩张器的鞘管、）打开球囊包（也有扩张管），用单向阀连接注射器和球囊，抽吸30ml 空气后，取出球囊。
SICK Safety Designer软件发布说明说明书
A D D I T I O N A L I N F O R M A T I O NSafety Designer Software – Release NotesmicroScan3New product outdoorScan3: Core I/O and Pro EtherNet/IP 4 m availableMajor bugfix: Fixed a bug that prevented Safety Designer 1.6 to work with microScan3 Core I/O with version of functional scope 1.0.0Report improvement: Device temperature (temperature inside of device) now visible in report chapter device statusDefault device names are introduced, instead of microScan3, now complete naming is used. E.g. mS3 Core I/O instead of only microScan3. These default names are also set when resetting device to default settingsMinor bugfix Event history did not show events if very first event was triggered by contour detection or reference contour fieldEtherNet/IP™ is a registered trademark of ODVA, Inc.GeneralGeneral stability improvements and bugfixesPerformance optimizationsFlexi Soft product familySupport for the following modules of the Flexi Soft safety controller:o Main module: FX3-CPU0 (FW 4.x)o Gateway modules: FX0-GETC, FX0-GMOD, FX0-GCAN, FX0-GPNT (FW 3.x), FX0-GENT (FW 3.x)o I/O modules: FX3-XTIO (FW 3.x), FX3-XTDI (FW 3.x), FX3-XTDS (FW 3.x), FX3-STIO (FW 3.x)o Motion Control module: FX3-MOC1 (FW 3.x)New product Flexi Soft EFI-pro gateway module: FX3-GEPREFI-pro systemEasy creation of safety networks for EFI-pro devicesSupport of time synchronization in the EFI-pro system via sNTPIntegration of EtherNet/IP CIP Safety devices into the EFI-pro systemmicroScan3New product microScan3: Core and Pro EFI-pro 4/5,5/9 m availableNew function: time synchronization over sNTP now supported by all new microScan3 EFI-pro and EtherNet/IP variants.General bugfixesMeasurement data output: Updated texts to match data output description, context help now workingError report improved. Now also shows details to time of occurencePasswords limited to ASCII symbolsLive Monitor now availableCase table can be printed as pdfGeneralThe system requirements are checked when starting the program General stability improvements and bugfixesPerformance optimizationsmicroScan3New product microScan3 Core and Pro EtherNet/IP 9 m available New product microScan3 Core and Pro EFI-pro 9 m availableNew product microScan3 Core and Pro PROFINET 9 m available New product microScan3 Core IO 9 m and IO AIDA 9 m available General bugfixesBetter stability by resolving all known causes for crashesCorrections of textsVarious improvements for usabilityEtherNet/IP™ is a registered trademark of ODVA, Inc.GeneralImprovements in diagnosis/event historyGeneral stability improvementsA problem is corrected that lead to a mix of languages of some texts.microScan3New product microScan3 Pro PROFINET availableNew product microScan3 Pro EtherNet/IP™ availableNew product microScan3 Pro EFI-pro availableNew product microScan3 Core EFI-pro availableNew functions for microScan3 Core EtherNet/IP™ become available.Device version 1.2 introduces measurement data output and the possibility to configure behavior after connection is lost. It is now possible to configure an automatic restart after connection loss.General bugfixesBetter stability by resolving all known causes for crashes.Corrections of textsVarious improvements for usabilityEtherNet/IP™ is a registered trademark of ODVA, Inc.GeneralImprovements of message historyPreparation for PROFINET, EtherNet/IP™ and AIDA safety laser scannersDisplay of device path on the device tileImproved performance of data recorderGeneral bugfixing and stability improvementsmicroScan3 CoreEvent history for all microScan3 variants now available in Safety Designer V1.3New product microScan3 Core – EtherNet/IP™ availableSupport of EtherNet/IP™ CIP Safety™ ProtocolNew product microScan3 Core – PROFINET availableSupport of PROFINET PROFIsafe ProtocolNew product microScan3 Core I/O AIDA availableNote: The version number of microScan3 Core I/O can now be selected when a microScan3 is created offline. New version number of microScan3 Core I/O is added.(version 1.1.).Devices with version number 1.1 will be available in December 2017 and are downward compatible to any configuration that was created as version 1.0.General bugfixesBetter stability by resolving all known causes for crashes.The visualisation of the checksums is improvedCorrections of textsVarious improvements for usability, e.g. editing of polygons in the field editor is improved.Added more languages: now available German, English, Spanish, Italian, French, Portuguese, Czech, Polish, Chinese and Japanese.Improvement of simulation, now fields can be moved into background.EtherNet/IP™ and CIP Safety™ are registered trademarks of ODVA, Inc.Version 1.2GeneralNew and enhanced functionalities in Safety Designer V1.2:Additional languages; now available: German, English, Spanish, Italian, French, Portuguese, Czech, Polish, Chinese and Japanese..NET Runtime is now part of SD distributionImprovements:Various bugs fixed within multi-language systemImproved stability in on-line use casesGeneral stability improved by consolidation and bug fixingmicroScan3 Core I/OGeneral bugfixesBetter stability by resolving all known causes for crashes.The visualisation of the checksums is improvedCorrections of textsVarious usability improvements, e.g. the editing of polygons in the field editor is improved.Improvement of simulation, now fields can be moved into background.Optimized calculation of checksums. When using this new version of Safety Designer, the check sum will change once (see Service Note S17121).Version 1.1 SP1GeneralIncreased communication performanceTools-menu extendedGeneral bugfixing and stabilizationUsability improvementsComplete integration of 5 languages (DE, EN, IT, ES, FR); corrections to the German version of the textsError, that prohibited starting Safety Designer on Turkish Windows-PCs, is resolved.microScan3 Core I/OmicroScan3 device window of Safety Designer and microScan3 user manuals are updated and available in German, English, French, Spanish and Italian.Display texts are updated and available in all 5 languages (DE, EN, IT, ES, FR)Error, that the display would show an error when accessing the infringement history on the display, is resolved.Version 1.1microScan3 Core I/O1. Increased stability of the Software:Sporadic crashes while carrying out the following actions are resolved: - Adding the microScan3 to a new project- Quickly changing between configuration tabs- while using the data recorderSporadic issues may be experienced during general usage/the following actions: - Connection to the device is lost- Field set editor freezes; a software restart is needed- The user level “maintenance” is not accessible; use authorized client instead- Transferring the configuration to the device occasionally fails- The “Verify” button is not shown- Drawing the reference contour field is not possible2. Improvement of usability and general bugfixing:The wrong date may be shown in the optical window replacement windowFields may not be shown correctly, when opening a saved projectHelp icons are not always shown in languages other than GermanPictures in help pop-ups are sometimes not shown correctlyWhen changing size of fields by mm in field editor, a double click is sometimes required to confirm changes; normal it would be single click.Drag and drop of fields in monitoring case table is only possible when the correct number of switch off paths has been created beforehand. This should happenautomatically.Using comma in field set editor can create problemsZooming in on the field editor also selects drawn shapesWhen no OSSD is assigned to a safety field, now a “to do” appearsWhen assigning an OSSD to a warning field now a “to do” and warning message appearsUndo and redo are added in field editorBackground image in field editor now in actual backgroundArea for showing measurement data in data recorder enlargedIcon to add a field and to add a field set optimizedWhen changing between fields, the zoom level stays the same now.Version 1.0.0GeneralFirst release of Software Safety Designer Version 1.0DocumentationUser Manual Safety Designer 8018179 DEUser Manual Safety Designer 8018180 ENUser Manual Safety Designer 8018191 FRUser manual microScan3 CoremicroScan3 Core I/OFirst module for Safety laser scanner microScan3 CoreSICK | Configuration Software Safety Designer – Release Notes Page 11 8019527/121A ● Release date: 2019-02-12/DS。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
ex
TEXTURE ANALYSIS FEATURES &SAFETY
校正平台 机型)力量感应元 器HI[计:1自]:l 倒霉3负载力量 仪器可以施加超过样品测试区 样品的地方。
Extrusion 周边附件 测试样品 要特别注意摆放测试样品，特。
可把
如果样品或者容器容易被破碎，应该在摆放样品或者操作仪器时，戴、、、
如需更多的讯息或者说明，请联络超技仪器
lotun_sales@ ；lotun168@
电路板 控制物性测试仪底
座的电路板(硬软件) 。
通
过一个简单的软件接口下载更新软件，安装后就添加新的特征。
、
PC 端口 连接计算机的插口，可以使软件控制仪器并能分析数据。
控制接口 操作物性测试仪力臂。
台北TEL:886-2-8228-0770 FAX:886-2-8228-0760 新北市中和区中正路716号14楼
北京TEL:010-8599-9920 FAX:010-8599-9920-800 北京市朝阳区安立路68号飘亮阳光广场A311室
上海TEL:021-6484-5711 FAX:021-6417-0072 上海市天钥桥路380弄20号15F(汇峰大厦) 成都TEL:028-8733-2977 FAX:028-8733-7404 成都市顺城大街308号冠城广场7楼S 座。