UG模具专业词汇

1 冲模dies (stamping and punching dies)
1.1 单工序模single operation dies
1.2 复合模compound dies
1.3 级进模progressive dies
1.4 无导向模opening dies
1.5 导板冲模guide plate dies
1.6 导柱模guide pillar dies
1.7 通用模universal dies
1.8 专用模dies for special purpose
1.9 自动模automatic dies
1.10 组合冲模combined dies
1.11 简易模low-cost dies
1.11.1 橡胶冲模rubber-dies
1.11.2 钢带模steel rule dies
1.11.3 低熔点合金模low-melting point alloys dies
1.11.4 锌基合金模zinc based dies
1.11.5 薄板模laminated dies
1.12 冲裁模blanking dies
1.1
2.1 落料模blanking dies
1.1
2.2 冲孔模piercing dies
1.1
2.3 切边模trimming dies
1.1
2.4 切口模notching dies
1.1
2.5 切舌模lancing dies
1.1
2.6 剖切模parting dies
1.1
2.7 整修模shaving dies
1.1
2.8 精冲模fine blanking dies
1.1
2.9 切断模cutting-off dies
1.13 弯曲模bending dies
1.13.1 卷边模curling dies
1.13.2 扭曲模twisting dies
1.14 拉伸模drawing dies
1.14.1 反拉伸模reverse redrawing dies
1.14.2 变薄拉伸模ironing dies
1.15 成形模forming dies
1.15.1 胀形模bulging dies
1.15.2 整形模sizing dies
1.15.3 缩口模necking dies
1.15.4 扩口模flaring dies
1.15.5 翻边模flanging dies
1.15.6 翻孔模burring dies
1.16 冷挤压模cold extruding dies
1.16.1 正挤压模forward extruding dies
1.16.2 反挤压模backward extruding dies
1.16.3 复合挤压模compound extruding dies
1.16.4 径向挤压模radial extruding dies
2 冲模零件
2.1 模架die、sets
2.1.1 弹压导板模架die sets with spring guide plate 2.1.2 后导柱模架back pillar (post) sets
2.1.3 对角导柱模架die gonal pillar (post) sets
2.1.4 中间导柱模架center pillar (post) sets
2.1.5 精冲模架fine blanking die sets
2.1.6 滑动导向模架sling guide die sets
2.1.7 滚动导向模架anti-frtion bearing die sets
2.1.8 通用模架universal die sets
2.2 工作零件working elements
2.2.1 凸模punch
2.2.2 凹模matrix
2.2.3 凸凹模punch-matrix
2.2.4 镶件insert
2.2.5 拼块section
2.2.6 柔性模flexile dies
2.3 定位零件locating elements
2.3.1 定位销locating pin (gauge pin)
2.3.2 定位板locating plate
2.3.3 挡料销stop pin
2.3.4 导正销pilot pin
2.3.5 导料板stock guide rail
2.3.6 定距侧刃pitch punch
2.3.7 侧刃挡块stop block for pitch punch
2.3.8 止退键die stop
2.3.9 始用挡料销(块) finger stop pin (block)
2.3.10 侧压板se-push plate
2.3.11 限位块(柱) limited block (post)
2.4 压料、卸料零件
2.4.1 卸料板stripper plate
2.4.2 推件块ejector
2.4.3 推杆ejector pin
2.4.4 推板ejector plate
2.4.5 连接推杆ejector tie rod
2.4.6 打杆knock out pin
2.4.7 顶件块ker
2.4.8 顶杆ker pin
2.4.9 卸料螺钉stripper bolt
2.4.10 拉杆tie rod
2.4.11 托杆pressure pin (cushion pin)
2.4.12 托板supporting plate (pressure plate)
2.4.13 废料切断刀scrap cutter
2.4.14 弹顶器cushion
2.4.15 承料板stock supporting plate
2.4.16 压料板pressure plate
2.4.17 压边圈blank holder
2.4.18 齿圈压板serrated ring
2.5 导向零件guide elements
2.5.1 导柱guide pillars (guide post)
2.5.2 导套guide bushes
2.5.3 导板guide plate
2.5.4 滑板sleek plate
2.5.5 耐磨板wear plate
2.5.6 弹压导板spring guide plate
2.5.7 钢球保持圈cage
2.5.8 止动件retainer
2.6 固定零件retaining elements
2.6.1 上模座punch holder (upper shoe)
2.6.2 下模座die holder (low shoe)
2.6.3 凸模固定板punch plate
2.6.4 凹模固定板matrix plate
2.6.5 垫板backing plate
2.6.6 模柄shank
2.6.7 浮动模柄self-centering shank
2.7 其他零件
2.7.1 斜楔cam driver
2.7.2 滑块sleek block
3 冲模设计术语
3.1 冲裁间隙blanking clearance
3.2 模具闭合高度die shut height
3.3 压力机闭合高度shut height of press machine 3.4 冲模寿命die life
3.5 压力中心center of load
3.6 冲模中心center of die
3.7 冲压方向pressing direction
3.8 送料方向feed direction
3.9 排样blank layout
3.10 搭边scrap
3.11 进距feed pitch
3.12 切边余量trimming allowance
3.13 毛刺burr
3.14 冲裁力blanking force
3.15 弯曲力bending force
3.16 拉伸力drawing force
3.17 挤压力extruding force
3.18 卸料力stripping force
3.19 推件力ejecting force
3.20 顶件力kking force
3.21 压料力pressure-plate-force
3.22 压边力blank holder force
3.23 毛坯blank
3.24 中性层neutral plane
3.25 弯曲角bending angle
3.26 弯曲线bending line
3.27 回弹spring back
3.28 相对弯曲半径relative bending radius
3.29 弯曲半径bending radius
3.30 最小弯曲半径minimum bending radius
3.31 弯曲件展开长度blank length of bends
3.32 拉伸系数drawing coefficient
3.33 拉伸比drawing ratio
3.34 拉伸次数drawing numbers
3.35 挤压比extruding ratio
3.36 缩口系数necking coefficient
3.37 扩口系数flaring coefficient
3.38 胀形系数bulging coefficient
3.39 翻孔系数burring coefficient
3.40 最小冲孔直径minimum diameter of piercing
3.41 转角半径radius
3.42 相对转角半径relative radius
3.43 相对高度relative height
3.44 相对厚度relative thickness
4 圆凸模结构要素
4.1 头部punch head
4.2 杆shank
4.3 刃口point
4.4 头厚punch head thickness
4.5 头部直径punch head diameter
4.6 连接半径radius
4.7 凸模圆角半径punch radius
4.8 杆直径shank diameter
4.9 引导直径lead diameter
4.10 过渡半径radius blend
4.11 刃口直径point diameter
4.12 刃口长度point length
4.13 凸模总长punch overall length
5 圆凹模结构要素
5.1 头部matrix head
5.2 模体body
5.3 刃口point
5.4 刃口直径hole diameter
5.5 刃口长度land length
5.6 刃口斜度point angle
5.7 凹模外径body diameter
5.8 头部直径matrix head diameter
5.9 头厚matrix head thickness
5.10 凹模圆角半径。

matrix fillet radius 5.11 凹模总长matrix overall length 5.12 引导直径lead diameter
5.13 排料孔relief hole
5.14 排料孔直径relief hole diameter 5.15 连接圆角fillet
5.16 压料板，压边圈blank holder
5.17 进料速度approaching speed
5.18 滑块上升速度slide upstroke speed 5.20 冲程stroke
5.21 支柱，支杆uprights。