检 验 报 告
合集下载
相关主题
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Classification of test: Commission test 检验类别：委托检验
Tested according to: ST/SG/AC, 10/11/Rev.5 Section 38.3: 2009 and of part 1 of packing instructions 967 of 52nd DGR manual of IATA 测试标准：UN38.3: 2009 +967 of 52nd DGR manual of IATA
Description of the sampling prwk.baidu.comcedure: 抽样程序的说明：
/
Description of the deviation from the standard, if any: 偏离标准方法的说明：
/
Remarks: 备注：
Throughout this report a comma is used as the decimal separator. 本报告中以逗号代替小数点。
Clause 章节
UN DOT 38.3 :2009/联合国专家委员会关于危险品的运输建议书
Requirements
Result
标准要求
测试结果
Verdict 判定
38,3
Lithium Batteries/锂电池
P
38,3,1
Purpose/目的
P
38,3,2
Scope/范围
P
38,3,3
Sample requirements/待测样品要求
The conditions of the batteries of sample No. b13# to b16# are after fifty cycles ending in fully charged state. 样品 b13#到 b16#在第五十个充放电循环，结束在完全充电状态。
The conditions of cells of sample c1# to c10# are at first cycle at 50% of the design rated capacity. 样品 c1#到 c10#在第一个充放电循环，结束在 50%的额定容量。
Approved by:
Reviewed by: Liu Yang
Tested by: Zhi Juncai
批准：
审核：
检测：
Ref. No.: RZUN2011-0813
Page 3 of 22 Pages
Description and illustration of the sample: 样品说明及描述：
Commission by: SHENZHEN REXPOWER ELECTRONICS CO., LTD 委托单位：深圳美拜电子有限公司
Commissioner address:BLK1-2, Hebei Industry Park, Longhua Town, Baoan Area, Shenzhen City, Guangdong Province 委托单位地址：广东省深圳市宝安区龙华镇三联村 河背工业区 1-2 栋
The samples’ status is good. 样品状态完好。
The Lithium Polymer Ion Batteries are 7255110-2P 7,4V 4900mAh 36,26Wh 7255110-2P 锂聚合物电池的额定值为 7,4V 4900mAh 36,26Wh。 The size of package is 323mm×420mm×320mm.Each package contains 5 batteries. The weight of the package is 10,30kg.
Manufacturer: SHENZHEN REXPOWER ELECTRONICS CO., LTD 制造商：深圳美拜电子有限公司
Manufacturer address: BLK1-2, Hebei Industry Park, Longhua Town, Baoan Area, Shenzhen City, Guangdong Province 制造商地址: 广东省深圳市宝安区龙华镇三联村河 背工业区 1-2 栋
Means of receiving: submitted by manufacturer 接样方式：厂家送样 Completing date: 鉴定完成日期：2011.09.28
Test conclusion:
The Lithium Polymer Ion Batteries submitted by SHENZHEN REXPOWER ELECTRONICS CO., LTD are tested according to Section 38.3:2009 of Amendments to the Fifth Revised Edition of the Recommendations on the Transport of Dangerous Goods, Manual of Test and Criteria (ST/SG/AC, 10/11/Rev.5). The package is conformed to the part 1 of packing instructions 967 of 52nd DGR manual of IATA 检验结论：
Appearance: ─ 样品外观颜色：─ Trade mark: 7255110 商标：7255110
Package of goods: ─ 样品外包装：─ Sample status: good 样品状态：完好
Quantity of sample：26pcs 样品数量：26pcs Sample identification: b1# ～b16#; c1#～c10# 样品标识序号：b1# ～b16#; c1#～c10#
Ref, No.: RZUN2011-0813
Photos of samples and markings 样品照片及标识
Battery（7255110-2P 7,4V 4900mAh 36,26Wh）
Page 4 of 22 Pages
Ref, No.: RZUN2011-0813
Photos of samples and markings 样品照片及标识
The conditions of the batteries of sample No. b5# to b8# are after fifty cycles ending in fully charged state. 样品 b5#到 b8#在第五十个充放电循环，结束在完全充电状态。
The conditions of the batteries of sample No. b9# to b12# are at first cycle, in fully charged state. 样品 b9#到 b12#在第一个充放电循环，结束在完全充电状态。
P
为未进行其他测试的样品
Test 7 may be conducted using
undamaged batteries previously used
in tests 1 to 5 for purposes of testing on cycled batteries/测试 7 中所采用的样
P
品可为通过测试 1 至测试 5 且未被损坏
six hour at ambient temperature (20±5℃)/将电芯和电池在温度为 20±5℃，大气
P
压力位不大于 11.6kPa 的环境中贮存不少于 6 个小时
38,3,4,1,3 Requirement/标准要求：
P
Cells and batteries Mass loss limit:≦0,1%/样品质量损失:≦0,1%
Test item: 7 items 测试项目: 7 项
Receiving date: 接样日期：2011.08.15
Name of samples: Lithium Polymer Ion Battery 样品名称: 锂聚合物电池
Type/ Model: 7255110-2P 7,4V 4900mAh 36,26Wh 型号规格：7255110-2P 7,4V 4900mAh 36,26Wh
packing photos
Page 5 of 22 Pages
Ref, No.: RZUN2011-0813
Photos of equipment 设备照片
Equipment (tablet / 平板电脑)
Page 6 of 22 Pages
Ref, No.: RZUN2011-0813
Page 7 of 22 Pages
检验报告
TEST REPORT
Page 1 of 22 Pages No.: RZUN2011-0813
NAME OF SAMPLE: Lithium Polymer Ion Battery 产品名称：锂聚合物电池
CLIENT: SHENZHEN REXPOWER ELECTRONICS CO., LTD 委托单位：深圳美拜电子有限公司
的样品
Ref, No.: RZUN2011-0813
Page 8 of 22 Pages
Clause 章节
UN DOT 38.3 :2009/联合国专家委员会关于危险品的运输建议书
Requirements
Result
标准要求
测试结果
Verdict 判定
38,3,4,1
Test 1:Altitude simulation/ 测试 1：高度模拟
Factory: SHENZHEN REXPOWER ELECTRONICS CO., LTD 生产厂：深圳美拜电子有限公司
Factory address: BLK1-2, Hebei Industry Park, Longhua Town, Baoan Area, Shenzhen City, Guangdong Province 生产厂地址：广东省深圳市宝安区龙华镇三联村河 背工业区 1-2 栋
P
38,3,4,1,1 Purpose/目的
P
This test simulate air transport under low-pressure conditions/本测试模拟低压条 件下的航空运输
P
38,3,4,1,2 Test procedure/测试步骤
P
Test cells and batteries shall be stored at a pressure of 11,6kPa or less for at least
由深圳美拜电子有限公司送检的锂聚合物电池,依据《关于危险品货物运输的建议书》第五修订版第 38.3 节进行检测。包装件依据 IATA 第 52 版 DGR 手册的包装说明 967 第一部分进行包装。
Test result: Pass. 检验结果：通过
Seal 公章 Date of issue: 签发日期：September 28,2011
P
38,3,4
Procedure/测试步骤
P
Test 1 to 5 must be conducted in
sequence. /测试 1 至测试 5 需按顺序
P
进行
Test 6 and 8 should be conducted
using not otherwise tested cells or batteries/测试 6 和测试 8 中所用的样品
包装箱尺寸为 323mm×420mm×320mm。每箱含 5 块电池。包装件重量为 10,30Kg。
The conditions of the batteries of sample No. b1# to b4# are at first cycle, in fully charged state. 样品 b1#到 b4#在第一个充放电循环，结束在完全充电状态。
CLASSIFICATION OF TEST: Commission test 检验类别：委托检测
广州邦禾检测技术有限公司
Guangzhou MCM Certification and Testing Co., Ltd
检验报告
TEST REPORT
NO.: RZUN2011-0813
Page 2 of 22 Pages
Tested according to: ST/SG/AC, 10/11/Rev.5 Section 38.3: 2009 and of part 1 of packing instructions 967 of 52nd DGR manual of IATA 测试标准：UN38.3: 2009 +967 of 52nd DGR manual of IATA
Description of the sampling prwk.baidu.comcedure: 抽样程序的说明：
/
Description of the deviation from the standard, if any: 偏离标准方法的说明：
/
Remarks: 备注：
Throughout this report a comma is used as the decimal separator. 本报告中以逗号代替小数点。
Clause 章节
UN DOT 38.3 :2009/联合国专家委员会关于危险品的运输建议书
Requirements
Result
标准要求
测试结果
Verdict 判定
38,3
Lithium Batteries/锂电池
P
38,3,1
Purpose/目的
P
38,3,2
Scope/范围
P
38,3,3
Sample requirements/待测样品要求
The conditions of the batteries of sample No. b13# to b16# are after fifty cycles ending in fully charged state. 样品 b13#到 b16#在第五十个充放电循环，结束在完全充电状态。
The conditions of cells of sample c1# to c10# are at first cycle at 50% of the design rated capacity. 样品 c1#到 c10#在第一个充放电循环，结束在 50%的额定容量。
Approved by:
Reviewed by: Liu Yang
Tested by: Zhi Juncai
批准：
审核：
检测：
Ref. No.: RZUN2011-0813
Page 3 of 22 Pages
Description and illustration of the sample: 样品说明及描述：
Commission by: SHENZHEN REXPOWER ELECTRONICS CO., LTD 委托单位：深圳美拜电子有限公司
Commissioner address:BLK1-2, Hebei Industry Park, Longhua Town, Baoan Area, Shenzhen City, Guangdong Province 委托单位地址：广东省深圳市宝安区龙华镇三联村 河背工业区 1-2 栋
The samples’ status is good. 样品状态完好。
The Lithium Polymer Ion Batteries are 7255110-2P 7,4V 4900mAh 36,26Wh 7255110-2P 锂聚合物电池的额定值为 7,4V 4900mAh 36,26Wh。 The size of package is 323mm×420mm×320mm.Each package contains 5 batteries. The weight of the package is 10,30kg.
Manufacturer: SHENZHEN REXPOWER ELECTRONICS CO., LTD 制造商：深圳美拜电子有限公司
Manufacturer address: BLK1-2, Hebei Industry Park, Longhua Town, Baoan Area, Shenzhen City, Guangdong Province 制造商地址: 广东省深圳市宝安区龙华镇三联村河 背工业区 1-2 栋
Means of receiving: submitted by manufacturer 接样方式：厂家送样 Completing date: 鉴定完成日期：2011.09.28
Test conclusion:
The Lithium Polymer Ion Batteries submitted by SHENZHEN REXPOWER ELECTRONICS CO., LTD are tested according to Section 38.3:2009 of Amendments to the Fifth Revised Edition of the Recommendations on the Transport of Dangerous Goods, Manual of Test and Criteria (ST/SG/AC, 10/11/Rev.5). The package is conformed to the part 1 of packing instructions 967 of 52nd DGR manual of IATA 检验结论：
Appearance: ─ 样品外观颜色：─ Trade mark: 7255110 商标：7255110
Package of goods: ─ 样品外包装：─ Sample status: good 样品状态：完好
Quantity of sample：26pcs 样品数量：26pcs Sample identification: b1# ～b16#; c1#～c10# 样品标识序号：b1# ～b16#; c1#～c10#
Ref, No.: RZUN2011-0813
Photos of samples and markings 样品照片及标识
Battery（7255110-2P 7,4V 4900mAh 36,26Wh）
Page 4 of 22 Pages
Ref, No.: RZUN2011-0813
Photos of samples and markings 样品照片及标识
The conditions of the batteries of sample No. b5# to b8# are after fifty cycles ending in fully charged state. 样品 b5#到 b8#在第五十个充放电循环，结束在完全充电状态。
The conditions of the batteries of sample No. b9# to b12# are at first cycle, in fully charged state. 样品 b9#到 b12#在第一个充放电循环，结束在完全充电状态。
P
为未进行其他测试的样品
Test 7 may be conducted using
undamaged batteries previously used
in tests 1 to 5 for purposes of testing on cycled batteries/测试 7 中所采用的样
P
品可为通过测试 1 至测试 5 且未被损坏
six hour at ambient temperature (20±5℃)/将电芯和电池在温度为 20±5℃，大气
P
压力位不大于 11.6kPa 的环境中贮存不少于 6 个小时
38,3,4,1,3 Requirement/标准要求：
P
Cells and batteries Mass loss limit:≦0,1%/样品质量损失:≦0,1%
Test item: 7 items 测试项目: 7 项
Receiving date: 接样日期：2011.08.15
Name of samples: Lithium Polymer Ion Battery 样品名称: 锂聚合物电池
Type/ Model: 7255110-2P 7,4V 4900mAh 36,26Wh 型号规格：7255110-2P 7,4V 4900mAh 36,26Wh
packing photos
Page 5 of 22 Pages
Ref, No.: RZUN2011-0813
Photos of equipment 设备照片
Equipment (tablet / 平板电脑)
Page 6 of 22 Pages
Ref, No.: RZUN2011-0813
Page 7 of 22 Pages
检验报告
TEST REPORT
Page 1 of 22 Pages No.: RZUN2011-0813
NAME OF SAMPLE: Lithium Polymer Ion Battery 产品名称：锂聚合物电池
CLIENT: SHENZHEN REXPOWER ELECTRONICS CO., LTD 委托单位：深圳美拜电子有限公司
的样品
Ref, No.: RZUN2011-0813
Page 8 of 22 Pages
Clause 章节
UN DOT 38.3 :2009/联合国专家委员会关于危险品的运输建议书
Requirements
Result
标准要求
测试结果
Verdict 判定
38,3,4,1
Test 1:Altitude simulation/ 测试 1：高度模拟
Factory: SHENZHEN REXPOWER ELECTRONICS CO., LTD 生产厂：深圳美拜电子有限公司
Factory address: BLK1-2, Hebei Industry Park, Longhua Town, Baoan Area, Shenzhen City, Guangdong Province 生产厂地址：广东省深圳市宝安区龙华镇三联村河 背工业区 1-2 栋
P
38,3,4,1,1 Purpose/目的
P
This test simulate air transport under low-pressure conditions/本测试模拟低压条 件下的航空运输
P
38,3,4,1,2 Test procedure/测试步骤
P
Test cells and batteries shall be stored at a pressure of 11,6kPa or less for at least
由深圳美拜电子有限公司送检的锂聚合物电池,依据《关于危险品货物运输的建议书》第五修订版第 38.3 节进行检测。包装件依据 IATA 第 52 版 DGR 手册的包装说明 967 第一部分进行包装。
Test result: Pass. 检验结果：通过
Seal 公章 Date of issue: 签发日期：September 28,2011
P
38,3,4
Procedure/测试步骤
P
Test 1 to 5 must be conducted in
sequence. /测试 1 至测试 5 需按顺序
P
进行
Test 6 and 8 should be conducted
using not otherwise tested cells or batteries/测试 6 和测试 8 中所用的样品
包装箱尺寸为 323mm×420mm×320mm。每箱含 5 块电池。包装件重量为 10,30Kg。
The conditions of the batteries of sample No. b1# to b4# are at first cycle, in fully charged state. 样品 b1#到 b4#在第一个充放电循环，结束在完全充电状态。
CLASSIFICATION OF TEST: Commission test 检验类别：委托检测
广州邦禾检测技术有限公司
Guangzhou MCM Certification and Testing Co., Ltd
检验报告
TEST REPORT
NO.: RZUN2011-0813
Page 2 of 22 Pages