x 产品技术支持信息周报 (2012年九月第五版)

合集下载

Power&存储产品技术支持信息周报 (八月第一版)

Power&存储产品技术支持信息周报 (八月第一版)【周报导读】一． 7042-CR6 中的 feature #1208 的含义，这个 feature 可以不配置吗；二． 7226-1U3 的物理参数介绍；三． Power 服务器的电源和耗电量计算方法；四．什么是 Thermal Power Management Device(TPMD), 它可以实现哪些功能；五 . V7000 mirrored volume 应用方式；六 .Nseries 中 NAS 和 SAN 的区别；七 . XIV 磁盘、缓存及接口详细参数【周报详情】一. 7042-CR6中的feature #1208的含义，这个feature可以不配置吗:解答：Feature #1208是USB闪存（U盘），它使用HMC上的USB端口，代替DVD RAM进行HMC自身数据的备份和恢复。

不配这个#feature从技术上讲是不会影响HMC使用的，但目前econfig会默认加上这个选项,不需要可以手动删除。

目前HMC备份自身数据有四种方式：1.通过自身的DVD-RAM光驱将数据刻录到光盘上。

2.通过NFS将数据备份到NFS server上。

3.通过FTP将数据备份到FTP server上。

4.将数据备份到USB闪存（U盘）上，需要HMC软件版本V7 R342 or later。

二. 7226-1U3的物理参数介绍:解答：宽: 480 mm (18.9 in)深: 454 mm (17.9 in)高: 43 mm (1.69 in)重量：空媒体抽屉：5.1 kg (11.2 lbs)典型配置：7.1 kg (15.6 lbs)供电电源：140 watts三. Power服务器的电源和耗电量计算方法：解答：POWER6/7 服务器的计算方式参考如下的网页：/see/EnergyEstimator1.注意，在每次进入计算工具之前，需要接受一个使用该计算工具的许可，您可以在看完该许可以后，点击“I accept”即可。

x 产品技术支持信息周报 (2012年一月第三版)

X3500M3(7380)X3400M3(7379,7378)X3250M3(4251,4252)X3200M3(7327,7328)四.哪些服务器集成了VFA II?A：除了标准PCIe的VFA II Option（49Y7950）外，x3850X5/x3950X5/x3690X5上还标配了Integrated VFAII（SBB: 49Y7940）。

这三种机型上都有一个专用的槽位，只能用来安装Integrated Emulex VFAII(49Y7940)。

Integrated VFA II（SBB: 49Y7940）和VFA II Option (option PN: 49Y7950)在功能上完全一致。

因此，您可以选择预装了Integrated Emulex VFA II的服务器型号，也可以通过安装VFA II Option Card 的方式，来使用Emulex 10Gb VFA II for IBM System x。

五.VFA II for x和for Blade的比较?A：VFA II for System x和VFA II for BladeCenter都是基于Emulex BladeEngine 3(BE3) 芯片,功能上一致。

都是2个10Gb物理端口，支持多达8个vNIC，通过付费升级的方式支持FCoE和iSCSI功能（当启用FCoE 或iSCSI功能时，每个物理端口虚拟的4个vNIC中有一个作为FCoE或iSCSI连接，其余三个仍为vNIC）。

VFA II for System x的vNIC管理与设置和VFA II for BladeCenter相同。

VFA II for System x的FCoE License（49Y4274）已经于2011/12/9 GA, iSCSI License即将发布。

而VFA II for BladeCenter的FCoE/iSCSI License都已经发布(49Y4265)。

DELTA DOP-B05高色彩宽屏用户友好HMI产品说明书

DOP -B05High Color Wide Screen User-Friendly HMI ProductsB05S111 Instrunction Sheet(1) PrefaceThank you for purchasing DELTA’s DOP-B series. This instruction sheet will be helpful in the installation, wiring and inspection of Delta HMI. Before using the product, please read this instruction sheet to ensure correct use. You should thoroughly understand all safety precautions before proceeding with the installation, wiring and operation. Place this instruction sheet in a safe location for future reference. Please observe the following precautions:Install the product in a clean and dry location free from corrosive and inflammable gases or liquids. Ensure that all wiring instructions and recommendations are followed. Ensure that HMI is correctly connected to a ground. The grounding method must comply with the electrical standard ofthe country (Please refer to NFPA 70: National Electrical Code, 2005 Ed.). Do not disassemble HMI, modify or remove wiring when power is applied to HMI. Do not touch the power supply during operation. Otherwise, it may cause electric shock.If you have any questions during operation, please contact our local distributors or Delta sales representatives.The content of this instruction sheet may be revised without prior notice. Please consult our distributors or download the most updated version at /ia(2) Safety PrecautionsCarefully note and observe the following safety precautions when receiving, inspecting, installing, operating,maintaining and troubleshooting. The following words, DANGER, WARNING and STOP are used to mark safety precautions when using the Delta’s HMI product. Failure to observe these precautions may void the warranty! InstallationWiringOperationD o not modify wiring during operation. Otherwise it may result in electric shock orpersonal injury.N ever use a hard or pointed object to hit or strike the screen as doing this may damage thescreen and let the screen has not respond at all, and then cause HMI to work abnormally.Maintenance and InspectionD o not touch any internal or exposed parts of the HMI as electrical shock may result.Do not remove operation panel while power is on. Otherwise electrical shock may result. W ait at least 10 minutes after power has been removed before touching any HMI terminalsor performing any wiring and/or inspection as an electrical charge may still remain in the HMI with hazardous voltages even after power has been removed. T urn the power off before changing backup battery and check system settings after finishing change. (all data will be cleared after changing battery). B e sure the ventilation holes are not obstructed during operation. Otherwise malfunction may result due to bad ventilation or overheating troubles.Wiring MethodCommunication Wiring(3) Pin Definition of Serial CommunicationNote2: B05S111 models do not support RS-422 flow control function. Note3: COM3 is the extension port (COM2 and COM3 share one physical port)(4) Parts NamesDOP-B05S111 (Front View)A Power LED Indicator (Lights in green when HMI works normally.) BTouch Screen / DisplayDOP-B05S111 (Rear View)(5) DimensionsNote:T=1.6mm(0.063")~ 6mm(0.24")BUnits: mm (inches)(6) SpecificationsL C D M O D U L EDisplay Type 5.6” TFT LCD (65536 colors) Resolution 320 x 234 pixelsBacklight LED Back Light (less than 20,000 hours half-life at 25C) (Note 1)Display Size113.28 x 84.70mm Operation SystemDelta Real Time OS MCU 32-bit RISC Micro-controllerNOR Flash ROMFlash ROM 128 MB(OS System: 30MB / Backup: 16MB / User Application: 82MB)SDRAM 64Mbytes Backup Memory 16MbytesSound EffectOutput Buzzer Multi-Tone Frequency2K ~ 4K Hz85dBAUX N/A Ethernet InterfaceN/AUSB 1 USB Host (Note 2) Ver 1.1 / 1 USB Slave Ver 2.0Memory Card N/ASerial COM PortCOM1 RS-232 (supports hardware flow control)COM2 RS-232RS-485 COM3RS-422RS-485Function Key N/A Perpetual Calendar (RTC) Built-inCooling Method Natural air circulation Safety ApprovalCEUL (Note 3)KCC (Note 3)WaterproofDegree IP65NEMA4OperationVoltage (Note 4) DC +24V -10% ~ +15%(please use isolated power supply)Voltage Endurance AC500V for 1 minute (between charging (DC24V terminal) and FG terminals) PowerConsumption (Note4) 3.0W Backup Battery 3V lithium battery CR2032 x 1Backup BatteryLife It depends on the temperature used and the conditions of usage,about 3 years or more at 25C.Operation Temp. 0oC ~ 50oC Storage Temp. -20oC ~ +60oCAmbient Humidity 10% ~ 90% RH [0 ~ 40C], 10% ~ 55% RH [41 ~ 50C]Pollution Degree 2Vibration IEC 61131-2 compliant 5Hz f 8.3Hz = Continuous: 3.5mm,8.3Hz f 150Hz = Continuous: 1.0gShock IEC 60068-2-27 compliant 15g peak for 11 ms duration, X, Y, Zdirections for 6 timesDimensions (W) x (H) x (D) mm 184 x 144 x 50 Panel Cutout (W) x (H) mm172.4 x 132.4 WeightApprox.670gsupplied to HMI. The life of LED backlight shown here is an estimated value under 25C normal temperature and humidity conditions.2) USB Host port can provide up to 5V/ 500mA of power.3) Some models are in the process of application to UL and KCC certification. For more information, please consult our distributors.4) The value of the power consumption indicates the electrical power consumed by HMI only without connecting to anyperipheral devices. In order to ensure the normal operation, it is recommended to use a power supply which the capacity is 1.5 ~2 times the value of the power consumption.5)The content of this quick start may be revised without prior notice. Please consult our distributors or download the most updated version at /ia/.。

x产品技术支持信息周报(2014年五月第三版)

x产品技术支持信息周报（2014年五月第三版）【周报导读】一、X3850X6最多支持多少内存？二、X3950X6最多支持多少内存？三、X3250M5可以支持多少块硬盘？四、X3850X6标配什么网卡？五、X3850X6的PCI E插槽能否支持热插拔？六、CMM中如何改变计算节点的启动项？七、IO BOOK有哪几种？八、如何通过IMM安装操作系统？九、服务器CPU的基本功能？十、I NTEL超线程技术简介？【周报内容】一、X3850 X6最多支持多少内存？A: 使用RDIMMs: 配置4颗CPU时最多1.5 TB使用96x 16 GB RDIMMs 使用LRDIMMs:配置4颗CPU时最多6 TB 使用96x 64 GB LRDIMMs请参考以下红皮书：/Redbooks.nsf/RedbookAbstracts/tips1084.html二、X3950 X6最多支持多少内存？A: 使用RDIMMs:当配置8颗CPU时最多3TB使用192x 16 GB RDIMMs 使用LRDIMMs:当配置8颗CPU时最多12TB使用192x 64 GB LRDIMMs请参考以下红皮书：/Redbooks.nsf/RedbookAbstracts/tips1132.html三、X3250 M5 可以支持多少块硬盘？A: X3250 M5 可选的机型有：●Four 2.5-inch small form factor (SFF) SAS/SATA hot-swap drive bays●Eight 2.5-inch SFF SAS/SATA hot-swap drive bays●Four 2.5-inch SFF SAS/SATA simple-swap drive bays●Eight 2.5-inch SFF SAS/SATA simple-swap drive bays●Four 3.5-inch large form factor (LFF) SAS/SATA hot-swap drive bays●Four 3.5-inch LFF SATA simple-swap drive bays部分标配带M1115阵列卡或者N2115 HBA卡的机型可以添加选件00AL348 x3250 M5 HS 2.5" HDD 4 to 8 Upgrade Kit 升级到8块2.5寸硬盘，如果标配是H1110阵列卡的4块2.5寸硬盘机型不可以升级到8块硬盘，如下图所示：更多详细信息参考相关red book：/abstracts/tips1050.html?Open#disk_int四、X3850 X6标配什么网卡？A: 标配大部分的basemodel都是4个千兆网卡，也有标配带2个万兆的机型，具体情况参考下面表格：从上面表格可以看出，只有B3X的机型标配是Broadcom NetXtreme II ML2 Dual Port 10GbE SFP+的网卡，其他机型都市Intel I350-T4 ML2 Quad Port GbE Adapter (I350-AM4 based)。

IBM技术支持信息周报 (2011年八月第一版)

三.x3650M3是否可以支持系统下的mirror?A：系统下的mirror功能是一种软件模拟的阵列功能，由操作系统提供。

由于IBM的服务器在装系统的时候一般都已经做了硬件阵列，所以再配置软件阵列的意义不大。

关于windows系统下的安装方式，请参考微软网站的相关说明。

/kb/323432四.x3850X5两个固态硬盘背板需要几个阵列卡?A：x3850X5配置两个固态硬盘背板需要两个B5015阵列卡。

详情可参考红皮书：http:///abstracts/tips0817.html?Open如下图所示：五.如何把imm接口与第一个网口共享?A：可以进入服务器UEFI中进行设置，选项为System Settings --> Intergrated Managerment Module --> Network Configuration设置为Sharted。

详情如下图：六.17352GX如何进行网络配置?A：新的KVM有远程访问与控制的功能，要使用是这个功能需要先在本地的控制台里面配置好IP才行。

也就是按两下CTRL打开本地的控制界面，然后如下依次打开，就能进行网络配置：From the side navigation bar,select Unit View>Appliance>ApplianceSettings>Network>General.The Appliance General Network Settings screen appears.七.460w和675w HE电源的好处?A：1、选择460W的好处：v a.节约成本，460W电源配置的价格相较于675W较低，有利于竞争v b.简配实用，满足大多数需求，和竞争对手对应 --- HP同样实用460W电源v c.相对来说比675W传统电源更节能d.电源输出功率在50%额定功率下最节能，大多数应用的实际平均负载在200-300W之间2、选择675W HE的好处：v a.可以实现对所有配置的全冗余配置v b.相对于675W传统电源来说成本增加不大v c.提高电源效率3%，为客户节约电费支出八.BCS的硬盘笼能否实现存储共享?A：使用SAS Connectivity Module连接的BCS里的硬盘，目前只能分配给指定的刀片，供某个刀片独立使用，不能实现刀片之间的存储共享；SAS RAI D Module可以实现存储共享。

Power&存储产品技术支持信息周报 (三月第二版)

Power&存储产品技术支持信息周报 (三月第二版)【周报导读】一． Power 730CPU ，内存和带宽信息；二．如何实现 Power730 的 RAID 功能；三．是否可以在 Power 720(8202-E4C) 或 740(8205-E6C) 的 e-config 中删除或替换FC9055 ；四．如何实现 Power740 的背板分离；N3200 系列产品介绍；五 .V7000U 内部以及主机连接方式；六 .七 .LTFS e-config 配置注意事项【周报详情】一. Power 730 CPU，内存和带宽信息:解答：CPU:64-bit POWER73.0 GHz (4) | 83.7 GHz (4) | 83.7 GHz (6) | 123.55 GHz (8) | 16内存：8231-E2B：8 GB -128 GB (1066 MHz DDR3)8231-E2C：8 GB -256 GB (1066 MHz DDR3)带宽：L1(data) cache : 144 GB/s(3.0GHz); 170.4 GB/s(3.55GHz);178.56 GB/s(3.7 GHz)L2 Cache:144 GB/s(3.0GHz); 170.4 GB/s(3.55GHz);178.56 GB/s(3.7 GHz)L3 Cache: 96 GB/s(3.0GHz); 113.6 GB/s(3.55GHz); 119.04 GB/s(3.7 GHz)System Memory：136.44GB/s (68.22 GB/s per socket)GX++ Bus: 40GB/sGX+ Bus:10GB/sTotal IO: 50GB/s二. 如何实现Power730的RAID功能:解答：Power 730在e-config有两个版本，分别是8231-E2B和8231-E2C，8231-E2C是IBM新发布的Power730版本，以前的8231-E2B在e-config还可以配置。

x 产品技术支持信息周报 (2012年二月第一版)

A：x3650M3内存插槽及安装顺序如下：
内存配置规则：
◦每个CPU 3个内存通道
◦每个通道安装一条内存时，内存运行速度 1333MHz；
◦安装两条内存时，运行速度1066MHz；
◦安装三条内存时，运行在800MHz
◦如为x5600 CPU 不两条内存时不降频
二.x3650M3硬盘如何配置?
A：硬盘配置规则如下：
背板连接效果图：
三.Setup Utility常见功能?
A：系统启动后，按F1进入。

查看系统信息
- 如关键产品信息
- 系统配置信息
更改系统参数
- CPU设置，如开启超线程，开启/关闭核心
- 设置可用内存条数
- I/O设置
- 电源策略
- 运行模式
- Legacy 支持遗留系统
- IMM 设置（包括IMM 网络配置，重设等）
- 安全设置
- 驱动设置
- 网络设置
四.如何使用Vmware嵌入式管理程序?
A：Vmware 嵌入式管理程序：
◦为集成虚拟化软件
◦USB Memory Key安装在SAS转接卡的USB系统管理程序接口中◦目前可支持的选择包括：
要开始使用嵌入式虚拟化软件，必须先将USB存储钥匙添加到Setup Utility的启动顺序中
五.M5016阵列卡介绍?
A：请参考下图介绍：
六.SAS线缆选件39R6529/39R6531的接口是什么规格?
A：接口规格是标准Mini-SAS (SFF-8088)，如下图所示：
详细可参考红皮书内容：/abstracts/tips0824.html?Open
/abstracts/tips0844.html?Ope。

QFD(质量功能展开)【范本模板】

QFD（质量功能展开)—-一种以市场为导向、以用户需求为依据的计划方法:在“用户就是上帝"的今天,不断满足用户的需求已经成为各公司致力的目标，QFD正是一种以市场为导向、以用户需求为依据的强有力的计划方法.QFD产生于日本.在60年代，随着TQC的深入，日本人开始考虑能否在产品的设计阶段就确定制造过程中的质量控制要点，以减少生产初期大量错误的发生。

1972年，三菱重工有限公司神户造船厂首先使用了QFD。

QFD就是一种在开发阶段就对产品的适用性实施全方位保证的系统方法。

美国而后引入了QFD 技术,并在汽车工业和国防工业进行推广，进一步的提高了QFD技术。

目前，质量功能展开已在全球几十个国家得到应用。

QFD作为一种策划工具，已经不只被应用于最初的生产领域，而且被广泛的应用于非生产领域,如服务业，软件业等。

由前面的叙述可知,产品开发各阶段质量屋的建立目的是进行需求变换.来自市场顾客的原始需求由产品规划阶段质量屋转换成为工程特征要求，即通常意义上的工程设计目标要求，工程特征要求经零部件设计阶段质量屋转换成零部件特征要求，零部件特征要求由工艺规划阶段质量屋转换成对制造工艺的要求，制造工艺要求最后由生产计划阶段的质量屋转换成具体的生产要求、市场顾客需求通过一系列的转换最终由生产要求来满足。

这一系列的需求转换过程就是系统的QFD技术过程，将QFD方法称为系统化方法的意思即在于此。

将各阶段的质量屋接输入输出关系相联接就构成一个完整的产品开发的QFD系统，如图3—22所示。

图3—22 系统的QFD过程综合以上的论述，总结QFD的特点如下：1）QFD的整个过程是以满足市场顾客需求为出发点的,各阶段的质量屋输入和输出都是市场顾客的需求所驱动，以此保证最大限度地满足市场顾客需求.这是市场规律在工程实际中的灵活应用。

2）在QFD系统化过程的各阶段都是将市场顾客需求转化为管理者和工程人员能明确理解的各种工程信息,减少或避免了产品从规划到产出各环节的盲目性。

x 产品技术支持信息周报 (2011年十二月第三版)

三.C100如何设置热备盘?A：1.选择Drive Management->Select Drive Operations，在Select Drive中选择需要设置为Hot Spare盘的硬盘，在Drive Operation中选择Assign Global Hot Spare Drive，然后选择Start Operation执行操作。

2.在Drive Management->View Global Hot Spare Drives中可以查看设置好的Hot Spare硬盘3.同样在Drive Management->Select Drive Operations界面中可以将Drive Operation选择为Unassign Hot Spare Drive来取消Hot Spare硬盘。

四.Linux下C100的驱动如何安装?A：C100 Llinux驱动安装方法比较特殊请参考下面的说明。

安装下面版本的linux都可以自认网卡驱动，无需额外装。

·sles10 sp4/support/fixcentral/systemx/quickorder?parent=ibm~Systemx3100M4&product=ibm/systemx/2582&&platform=SLES+10&function=fixId&fixids=ibm_dd_megasr_14.05.0701.2011_sles10_32-64&includeRequisites=1&includeSupersedes=0&downloadMethod=http&source=fc·sles11 sp1/support/fixcentral/systemx/quickorder?parent=ibm~Systemx3100M4&product=ibm/systemx/2582&&platform=SLES+11+x64&function=fixId&fixids=i bm_dd_megasr_14.05.0701.2011_sles11_32-64&includeRequisites=1&includeSupersedes=0&downloadMethod=http&source=fc·rhel6.1/support/fixcentral/systemx/quickorder?parent=ibm~Systemx3100M4&product=ibm/systemx/2582&&platform=RHEL+6&function=fixId&fixids=ibm_dd _megasr_14.05.0701.2011_rhel6_32-64&includeRequisites=1&includeSupersedes=0&downloadMethod=http&source=fc·rhel5.6/support/fixcentral/systemx/quickorder?parent=ibm~Systemx3100M4&product=ibm/systemx/2582&&platform=RHEL+5&function=fixId&fixids=ibm_dd _megasr_14.05.0701.2011_rhel5_32-64&includeRequisites=1&includeSupersedes=0&downloadMethod=http&source=fc五.C100软件阵列如何检查硬盘状态?A：选择Drive Management->View Drive Properties，在Select Drive上按回车可以看到硬盘的数量和状态，在图里中我们看到安装了2块500G的硬盘，状态是Unconfigured Good，可以配置阵列。

USCAR-2(中文第5版)-2009[1].03.17

研究数据、分析、结论、观点和本文的其他内容仅仅是作者的产品。

无论是汽车工程师协会(SAE)还是美国汽车研究委员会(USCAR)都不会出具任何证明某些产品符合基本要求的证书，也不会对本文内容的准确性和适用性作任何介绍。

确定本文内容是否适用于自己的目的，完全是本文用户责任。

版权 2004, USCAR 美国印刷
版权所有
有关本文件的问题： (724) 772-8545 传真 (724)776-0243
要订购文件： (724) 776-4970 传真 (724) 776-0790
Lock overtravel
Forward stop contacted
向前止动接触
Decreasing
Recognizable travel
distance
如果有适用的设备，强烈建议绘制所施加的啮合力与插入距离之间的连续对照图。

一个结构合理和密封系统，如适用的话) 应当能够绘制出一张图，其中显示力平稳上升至一个峰值，然后下降直至连接器完全啮合。

如果图中显示一个以上的力的峰值，锁止机构就可能存在错误。

第五修订版修订日期：2007-11
汽车电器连接器系统的性能标准
毫米/分的速率增加啮合力，直至完全啮合为止。

试验所有样品
．记录将每一套连接器的一半完全插入另外一半，直至锁定位置所需要使用的力并且用这些数值来验证每一对连接器是否符合5.4.2.4 章节的验收标准。

对已配合好的不包含端子和导线连接器。

、。

30115-EN

C ontentsC ontents1D escription of the measuring principle (3)2T ype overview (6)3M ounting instructions (8)4E lectrical connection4.1P reparing the connection (9)4.2W iring plan (9)5O peration5.1A djustment,general (13)6T echnical data (14)7D imensions (21)8P roduct code (23)T ake note of safety instructions for E x applicationsP lease note the E x speciﬁc safety information which you canﬁnd on our homepage \services\downloads and which comes with every instrument.I n hazardous areas you should take note of the appropriate regulations,conformity and type approval certiﬁcates of the sensors and power supply units.T he sensors must only be operated on intrinsically safe circuits.T he permissible electrical values are stated in the certiﬁcate.30115-EN-0811191D escription of the measuring principleM easuring principleVEGASWING is a point level sensor with tuning fork for level detection .I t is designed for industrial use in all areas of process technology ,but preferably in liquids .T he vibrating element (tuning fork )is energized piezoelectrically and vibrates at its mechanical resonance frequency .T he piezos are ﬁxed mechanically and are hence not subject to temperature shock limitations .I f the vibrating element is submerged in the product ,the vibrating frequency changes .T his change is de -tected by the integrated electronics module and converted into a switching command .T ypical applications are over ﬁll and dry run protection .T hanks to its simple and robust measuring system ,VEGASWING is virtually una ﬀected by the chemical and physical properties of the liquid .I t also works when subjected to strong external vibrations or changing products .F ault monitoringT he electronics module of VEGASWING monitors continuously the following criteria :l S trong corrosion or damage on the tuning fork l loss of vibrationl L ine break to the piezo driveI f one of the stated malfunctions is detected or in case of power failure ,the electronics takes on a de ﬁned switching condition ,for example ,the output transistor blocks (safe condition ).F unction testT he recurring function test is used to check the safety function ,in order to reveal possible non -detectable dangerous faults .T he function of the measuring system must be checked in regular ,adequate intervals .T here are two di ﬀerent ways to carry out a function test :VEGASWING 61,63with two -wire electronics in conjunctionwith a VEGATOR signal conditioning instrument .l T est key on the VEGATOR signal conditioning instrument VEGASWING 61,63with two -wire electronics in conjunctionwith a VEGALOG processing system or a PLC .l B rief interruption of the connection cable to the PLC VEGASWING 51T he small level switch model has a tuning fork 40mm long and a small ,compact stainless steel housing and is available as tran -sistor output and contactless electronic switch versions .VEGASWING 61,63VEGASWING series 60level switches are instruments from the VEGA plics ®series ,which are available in standard and tube version .plics ®instruments o ﬀer suitable versions for all applica -tions thanks to the many di ﬀerent process ﬁttings ,housings andelectronics versions .T hey have all the usual approvals and the tuning fork can also be polished ,e .g .for applications in the food processing industry .VEGASWING are virtually una ﬀected by product properties and thus do not have to be adjusted .T he level switches are used in applications with process temper -atures up to 250°C (482°F )and pressures of up to 64bar (928psig ).T hey detect liquids from 0.5…2.5g /cm ³(0.018…0.09lbs /in ³).A ll electronics are quali ﬁed for the function over ﬁll and dry run protection according to IEC 61508and 61511for SIL 2,in redun -dant version also for SIL 3.1.1A pplication examplesC hemical industry -SolventsF ig .1:L evel detection in vessels with solventsA part from the continuous level measurement ,level detection is an essential safety feature for storage tanks .M any modern sen -sors for continuous level measurement are actually approved as over ﬁll protectionsystem ,however ,a second ,physically di ﬀerent measuring system provides the best safety and redundance .T hanks to their manifold application possibilities ,VEGASWING vibrating level switches are ideal for all applications in the area of liquids warehousing .A large number of electrical and mechanical versions ensures simple integrationinto existing control systems .A dvantages :l V arious electrical versions l P roduct -independentl U niversal level detection for allliquids30115-E N -081119C hemical industry-reactorsF ig.2:L evel detection in chemical reactorsB ecause they prevent overﬁlling or dry runningof pumps,sensors for level detection are an important safety element in reactors.D ue to their universal applicability,VEGASWING level switches are well suited for use in reaction vessels.E ven high viscosities, temperaturesup to250°C and pressure up to64bar do not impair their function.T o provide the required chemical resistance,high resistance ma-terials and enamelled versions are available.I n toxic products,the VEGASWING version with metallic process separation ensures a high level of safety.T o prevent product leakage even in case of corrosion on the tuning fork,a glass seal is also welded in.T his guarantees optimum safety.T o provide optimal resistance to the measured medium,what-ever its composition and corrosive properties may be,sensors made of316L or H astelloy,or sensors in plastic-coated and enamelled versions,are available.T hanks to their manifold application possibilities,VEGASWING vibrating level switches are ideal for all applications in the area of liquids warehousing.A large number of electrical and mechanical versions ensures simple integrationinto existing control systems.A dvantages:l V arious electrical versionsl P roduct-independentl C ompletely gas-tightl H igh reliabilityl U niversal level detection for all liquids W ater/S ewage waterplantsF ig.3:P recipitants in sewage water processingC hemicals are required for sewage water treatment.T hey are applied to promote chemical precipitation in the process.P hos-phates and nitrates are sedimented and separated.I n addition to lime water and ferric chloride,various acids and lyes are stored for use in digested sludge treatment and neutralisation.T hese substances are subject to the regulations for water-endan-gering substances.I n accordance with this,overﬁll protection systems have to be installed on storage tanks.B ecause they prevent overﬁlling of vessels containing toxic prod-ucts,sensors for level detection are an important safety element.D ue to their versatile nature,VEGASWING vibrating level switches are also well qualiﬁed for use with water-endangering substances.T o provide optimal resistance to the measured me-dium,whatever its composition and corrosive properties may be, sensors made of316L,H astelloy,or sensors in plastic-coated or enamelled versions,are available.A dvantages:l H igh reproducibilityl H igh resistance sensor materials such as PFA,ECTFE,H as-telloy C4,enamelPipelinesF ig.4:D ry run protection in pipelinesM onitoring of levels is also important in pipelines,as dry running often causes damage or complete breakdown of the pumps.T he VEGASWING level switch is recommended as dry run pro-tection system,e.g.for drinking water pumps.W ith a fork only 40mm long,this level switch functions reliably,even in tubes with small diameters from DN32.A dvantages:l U niversal level detection for all liquidsl A djustment and maintenance-free30115-EN-081119F ood processing industryF ig .5:L evel detection and dry run protection in a tank storing milkT he processes in food processing tanks ,e .g .for milk ,place heavy demands on the installed measurement technology .H igh pressures and temperatures are generated during sterilization and cleaning of the tanks .T hat means that the implemented level measuring instruments and level detectors must meet the re -quirements of hygienic design .T he innocuousness of all wetted materials must be proven and optimum cleanability must be en -sured through hygienic technical design .VEGASWING is installed for level detection and as dry run pro -tection system .T he tuning fork is highly polished for use in sensi -tive foodstu ﬀs such as milk .A dvantages :l U niversal level detection for all liquidsl H igh resistance sensor materials such as PFA ,ECTFE ,H as -telloy C 4,enamell A djustment and maintenance -free30115-E N -0811192T ype overviewVEGASWING 51VEGASWING 61VEGASWING 63P referred application :L iquids L iquids L iquidsL ength :--80…6000mm (3.15…236.22in )P rocess ﬁtting :T hread G ¾A ,G 1AT hread G ¾A ,G 1A ,ﬂanges ,hygienic ﬁttingsT hread G ¾A ,G 1A ,ﬂanges ,hygienic ﬁttingsP rocess temperature :-40…+100°C (-40…+212°F )-40…+150°C (-40…+302°F )with temperature adapter-50…+150°C (-58…+302°F )-50…+250°C (-58…+482°F )with temperature adapter-50…+150°C (-58…+302°F )-50…+250°C (-58…+482°F )with temperature adapterP rocess pressure :-1…64bar (-14.5…928psig )-1…64bar (-14.5…928psig )-1…64bar (-14.5…928psig )S ignal output :transistor output ,contactless electronic switch R elay ,transistor ,two -wire ,NAMUR output ,contactless electronic switch R elay ,transistor ,two -wire ,NAMUR output ,contactless electronic switch R uggedness :+++S ensitivity :+++++B uildup :++++C leanability :++++++I nstallation length :++++++30115-EN -081119H ousingP lastic S tainless steel A luminiumA luminium (doublechamber )E lectronicsR elay output T ransistor outputC ontactless elec -tronic switchT wo -wire outputNAMUR outputS ensorsT uning forkA pprovalsG as explosion pro -tection30115-E N -0811193M ounting instructionsS witching pointI n general,VEGASWING can be installed in any position.T he instrument only has to be mounted in such a way that the vibrating element is at the height of the desired switching point.T he tuning fork has lateral markings(notches)marking the switchingpoint with vertical installation.T he switchingpoint refers tothemediumwaterwithbasicsettingofthedensityswitch≥0.7g/ cm³(0.025lbs/in³).K eep in mind that foams with a density>0.45g/cm³(0.016lbs/in³) are detected by the sensor.S ocketT he vibrating element should protrude into the vessel to avoid buildup.F or that reason,avoid using mountingbosses forﬂanges and screwedﬁttings.T his applies particularly to horizontal instal-lation and use with adhesive products.A gitatorsD ue to agitators,vibrations or similar,the level switch can be subjected to strong lateral forces.F or this reason,do not use an overly long extension tube for VEGASWING63,but check if a VEGASWING51or61level switch couldn't be used instead, mounted on the side of the vessel in horizontal position.E xtreme vibration caused by the process or the equipment,e.g. agitators or turbulence in the vessel,can cause the extension tube of VEGASWING to vibrate in resonance.T his leads to in-creased stress on the upper weld joint.S hould a longer tube version be necessary,you can provide a suitable support or guy directly above the vibrating element to secure the extension tube.T his measure applies mainly to applications in E x areas.M ake sure that the tube is not subject to bending stressdue to this measure.I nﬂowing mediumI f VEGASWING is mounted in theﬁlling stream,unwanted false measurement signals can be generated.F or this reason,mount VEGASWING at a position in the vessel where no disturbances, e.g.fromﬁlling openings,agitators,etc.,can occur.F ig.6:I nﬂowing mediumF lowsT o minimiseﬂow resistance caused by the tuning fork,VEGA-SWING should be mounted in such a way that the surfaces of the blades are parallel to the product movement.L ockﬁttingVEGASWING in tube version can be mounted with a lockﬁtting for inﬁnitely variable height adjustment.T ake note of the pressure speciﬁcations of the lockﬁtting.K eep in mind that the lockﬁtting must not be used with coated instrument versions.P ressure/V acuumT he processﬁtting must be sealed if there is gauge or low pres-sure in the vessel.C heck if the seal material is resistant against the measured product and the process temperature.P rotective coverT o protect the sensor against pollution and strong heat due to the sun,you can snap a weather protective cover onto the sensor housing.F ig.7:W eather protection cover in diﬀerentversions30115-EN-0811194E lectrical connection4.1P reparing the connectionN ote safety instructionsA lways keep in mind the following safety instructions :l C onnect only in the complete absence of line voltage T ake note of safety instructions for E x applicationsI n hazardous areas you should take note of the appro -priate regulations ,conformity and type approval certi ﬁ-cates of the sensors and power supply units .S elect power supplyC onnect the power supply according to the following diagrams .O scillators SW 60R and SW 60C are designed in protection class 1.T o maintain this protection class ,it is absolutely necessary that the ground conductor be connected to the internal ground termi -nal .T ake note of the general installation regulations .A s a rule ,connect VEGASWING to vessel ground (PA ),or in case of plastic vessels ,to the next ground potential .O n the side of the housing there is a ground terminal between the cable entries .T his con -nection serves to drain o ﬀelectrostatic charges .I n E x applica -tions ,the installation regulations for hazardous areas must be given priority .D ata for power supply is speci ﬁed in chapter "T echnical data ".S electing connection cableVEGASWING is connected with standard cable with round cross section .A n outer cable diameter of 5…9mm (0.2…0.35in )ensures the seal e ﬀect of the cable gland .I f cable with a di ﬀerent diameter or wire cross section is used ,exchange the seal or use an appropriate cable connection .I n hazardous areas ,only use approved cable connec -tions for VEGASWING .S elect connection cable for E x applicationsT ake note of the corresponding installation regulations for E x applications .4.2W iring planR elay output VEGASWING 61,63F ig .8:VEGASWING 61,63-electronics module with relay output 1C ontrol lamp2DIL switch for mode adjustment 3DIL switch for sensitivity adjustmentW e recommend connecting VEGASWING in such a way that the switching circuit is open when there is a level signal ,line break or failure (safe condition ).T he relays are always shown in non -operative condition .F ig .10:VEGASWING 61,63-wiring plan -relay output1R elay output 2R elay output 3V oltage supplyT ransistor outputW e recommend connecting VEGASWING in such a way that the switching circuit is open when there is a level signal ,line break or failure (safe condition ).T he instrument is used to control relays ,contactors ,magnet valves ,warning lights ,horns as well as PLC inputs .30115-E N -081119VEGASWING61,63F ig.12:VEGASWING61,63-electronics module with transistor output1C ontrol lamp2DIL switch for mode adjustment3DIL switch for sensitivity adjustmentF ig.14:VEGASWING61,63-transistor output-NPNactionF ig.16:VEGASWING61,63-transistor output-PNPaction F ig.18:W ire assignmentconnectioncable.T he numbers of the wires correspond to the terminals of the instrument.1brown(+)voltage supply2W hite3Y ellow4blue(-)voltage supply5S hieldingVEGASWING51F ig.19:VEGASWING51-transistor output with valve plug DIN43650PA P otential equalisationRL L oad resistance(contactor,relay,etc.)30115-EN-081119F ig .21:VEGASWING 51-transistor output with M 12x 1plug connection (housing )1B rown 2W hite 3B lue 4B lackRLL oad resistance (contactor ,relay ,etc .)C ontactless electronic switchW e recommend connecting VEGASWING in such a way that the switching circuit is open when there is a level signal ,line break or failure (safe condition ).T he contactless electronic switch is always shown in non -oper -ative condition .T he instrument is used for direct control of relays ,contactors ,magnet valves ,warning lights ,horns etc .I t must not be operated without an intermediately connected load ,because the elec -tronics would be destroyed if connected directly to the mains .I t is not suitable for connection to low voltage PLC inputs .T he domestic current is temporarily lowered below 1m A after switching o ﬀthe load so that contactors ,whose holding current is lower than the constant domestic current of the electronics ,are reliably switched o ﬀ.W hen VEGASWING is used as part of an over ﬁll protection sys -tem according to WHG ,also note the regulations of the general type approval .VEGASWING61,63F ig .23:VEGASWING 61,63-electronics module with contactlesselectronic switch 1C ontrol lamp2DIL switch for mode adjustment 3DIL switch for sensitivity adjustmentF ig .25:VEGASWING 61,63-wiring plan -output ,contactless electronic switch30115-E N -081119VEGASWING 51F ig .27:VEGASWING 51-contactlesselectronics switch with valve plug DIN 436501P rotection earthT wo -wire outputVEGASWING 61,63F ig .29:VEGASWING 61,63-electronics module with two -wire electronics1C ontrol lamp2DIL switch for sensitivity adjustmentW e recommend connecting VEGASWING in such a way that the switching circuit is open when there is a level signal ,line break or failure (safe condition ).F or connectionto a signal conditioninginstrument also E x .P ower supply via the connected signal conditioning instrument .F or fur -ther information see chapter "T echnical data ".T he wiring example is applicable for all suitable signal condition -ing instruments.F ig .31:VEGASWING 61,63-wiring plan -two -wire outputNAMUR output VEGASWING 61,63F ig .33:VEGASWING 61,63-electronics module with NAMUR electronics 1C ontrol lamp2DIL switch for characteristics reversal 3DIL switch for sensitivity adjustment 4S imulation keyF or connection of the ampli ﬁer according to NAMUR (IEC 60947-5-6,EN 50227).Y ou can ﬁnd further information in the "T echnical data ".F ig .35:W iring plan -NAMUR output30115-EN -0811195O peration5.1A djustment ,generalF ig .36:A djustment elements electronics module ,e .g .VEGASWING 61,63relay output (SW 60R )1S ignal lamp (LED )2DIL switch for mode adjustment 3DIL switch for sensitivity adjustmentS witching point adaptation VEGASWING 61,63W ith this DIL switch (2)you can set the switching point to liquids with a density between 0.5and 0.7g /cm ³(0.018and 0.025lbs /in ³).I n the basic adjustment ,liquids with a density >0.7g /cm ³(0.025lbs /in ³)can be detected .F or products with lower density,you have to set the switch to >0.5g /cm ³(0.018lbs /in ³).T he information about the position of the switching point relates to the medium water -density value 1g /cm ³(0.036lbs /in ³).W ith mediums of di ﬀering density ,the switching point shifts in the di -rection of the fork end ,depending on the density and manner of installation .VEGASWING 51P roducts with a density >0.7…2.5g /cm ³(0.025…0.09lbs /in ³)can be detected .T his setting cannot be modi ﬁed .T he switching status of VEGASWING can be checked when the housing is closed (signal lamp ,illuminated ring below the plug ).VEGASWING has an integrated test switch which can be acti -vated magnetically .T o test the instrument ,you have to hold the test magnet (accessory )to the magnet symbol on the instrument housing .T he test magnet changes the current switching condition of the instrument .Y ou can check the change on the signal lamp .P lease note that the connected instruments are activated during the test .M ode adjustment VEGASWING 61,63W ith the mode adjustment (min ./max .)you can change the switching condition of the output .Y ou can set the required mode (A /max .-max .detection or over ﬂow protection ,B /min .-min .detection or dry run protection ).VEGASWING 51W ith the correct polarity of the supply voltage ,the switching con -dition can be de ﬁned (max .detection /min .detection ).W ith the transistor output version ,PNP or NPN action can be reached by di ﬀerent connection of the consumer (load ).S ignal lamp (LED )VEGASWING 61,63D iode for indication of the switching status (with plastic housing visible from outside ).VEGASWING 51T he switching status of VEGASWING is visible from outside (con -trol lamp ,illuminated lens below the plug ).S imulation keyVEGASWING 61,63-NAMUR electronicsT he simulation key is located in a recess on the upper side of the electronics module .P ush the simulationkey with a suitable object (screwdriver ,pen ,etc .).W hen the key is pushed ,a line break between sensor and pro -cessing unit is simulated .T he signal lamp on the sensor extin -guishes .T he measuring system must signal a fault and take on a safe condition when the key is pushed .K eep in mind that downstream connected instruments will be activated during operation .T his allows you to check the correct function of the measuring system .C haracteristics reversalVEGASWING 61,63-NAMUR electronicsT he characteristics of the NAMUR electronics can be reversed with the DIL switch .Y ou can choose between falling character -istic curve (switch position max .)and rising characteristic curve (switch position min .).T his allows you to output the desired cur -rent .M odesl min .-rising characteristic curve (H igh current when im -mersed )l max .-falling characteristics (L ow current when immersed )T he NAMUR output can be switched to falling or rising character -istics .F or applications according to WHG ,the DIL switch must be set to position max .30115-E N -0811196T echnical dataG eneral dataM aterial 316L corresponds to 1.4404or 1.4435VEGASWING 51M aterials ,wetted parts -P rocess ﬁtting -thread 316L-P rocess seal K lingersil C -4400-vibrating element316LM aterials ,non -wetted parts -H ousing 316L and plastic PEI W eight250g (9oz )P rocess ﬁttings -T hreadG ¾A ,¾NPT ,G 1A ,1NPT-hygienic ﬁttings B olting DN 25PN 40,bolting DN 40PN 40,T ri -C lamp 1",T ri -C lamp 1½",SMSS urface quality -S tandardR a 3.2µm (1.26-4in )-H ygienic version R a <0.8µm (3.15-5in )VEGASWING 61,63M aterials ,wetted parts -P rocess ﬁtting -thread 316L ,H astelloy C 4(2.4610)-P rocess ﬁtting -ﬂange316L ,316L with H astelloy C 4coating ,steel enamelled ,316L with ECTFE coating ,316L with PFA coating -P rocess seal K lingersil C -4400-T uning fork316L /H astelloy C 4(2.4610)-E xtension tube :ø21.3mm (0.839in )316L ,H astelloy C 4(2.4610),H astelloy C 4(2.4610)enamelled ,316L with ECTFE coating ,316L with PFA coating S ensor length VEGASWING 61-L ength VEGASWING 61S ee chapter "D imensions "-switching point as VEGASWING 81or 81A L ength +51mm (+2in )S ensor length VEGASWING 63-316L ,H astelloy C 4(2.4610)80…6000mm (3.15…236.22in )-H astelloy C 4(2.4610)enamelled 80…1500mm (3.15…59.06in )-316L ,ECTFE coated 80…3000mm (3.15…118.11in )-316L ,PFA coated80…3000mm (3.15…118.11in )M aterials ,non -wetted parts -H ousingP lastic PBT (polyester ),A lu die -casting powder -coated ,316L -S eal between housing and housing cover NBR (stainless steel housing ),silicone (A lu /plastic housing )-L ight guide in housing cover PMMA (e .g .M akrolon )-G round terminal316L -T emperature adapter (optional )316L-G as -tight leadthrough (optional )316L /glassW eight-P lastic housing 760g (27oz )-A luminium housing 1170g (41oz )-S tainless steel housing1530g (54oz )-T ube extension VEGASWING 63approx .920g /m (9.9oz /ft )S urface quality -S tandardR a approx .3.2µm (1.26-4in )-H ygienic version (3A )R a <0.8µm (3.15-5in )-H ygienic version R a <0.3µm (1.18-5in )P rocess ﬁttings -T hread G ¾A ,¾NPT ,G 1A ,1NPT -F langesDIN from DN 25,ANSI from 1"-hygienic ﬁttings B olting DN 40PN 40,T ri -C lamp 1",T ri -C lamp 1½"PN 10,conus DN 25PN 40,T uchenhagen V arivent DN 50PN 10C oatings -ECTFE 0.5…0.8mm (0.02…0.031in )-PFA 0.3…0.5mm (0.01…0.02in )-E namel0.8mm (0.031in )H igh voltage test (enamel )>5KV30115-EN -081119G as -tight leadthrough (optional )-L eakage rate<10-6mbar l /s -P ressure resistance PN 64-hygienic ﬁttingsB olting DN 40PN 40,T ri -C lamp 1",T ri -C lamp 1½"PN 10,conus DN 25PN 40,T uchenhagen V arivent DN 50PN 10O utput variableR elay output O utputR elay output (DPDT ),2ﬂoating spdts T urn -on voltage -M in .10m V-M ax .253V AC ,253V DC S witching current -M in .10µA-M ax .3A AC ,1A DC B reaking capacity -M ax .1250VA ,50WC ontact material (relay contacts )A g C d O and A u plated M odes (adjustable )M in ./M ax .D elay time approx .-W hen immersed 0.5s -W hen laid bare 1sT ransistor output O utputﬂoating transistor output ,overload and permanently shortcircuit proof M ax .load current -VEGASWING 51250m A -VEGASWING 61,63400m A V oltage loss-VEGASWING 511V -VEGASWING 61,633VT urn -on voltage 55V DC B locking current <10µA M odes (adjustable )M in ./M ax .D elay time approx .-W hen immersed 0.5s -W hen laid bare1sC ontactless electronic switch O utputC ontactless electronic switch M odes (adjustable )M in ./M ax .D elay time approx .-W hen immersed 0.5s -W hen laid bare 1sT wo -wire output O utputT wo -wire outputS uitable signal conditioning instruments VEGATOR 536E x ,537E x ,636E xO utput signal -M ode min .V ibrating element uncovered :16m A ±1m A ,vibrating element covered :8m A ±1m A-M ode max .V ibrating element uncovered :8m A ±1m A ,vibrating element covered :16m A ±1m A -F ault message <2m AM odes (adjustable )min ./max .(changeover with the signal conditioning instrument )D elay time approx .-W hen immersed 0.5s -W hen laid bare 1sNAMUR output O utputT wo -wire NAMUR output30115-E N -081119C urrent consumption-F alling characteristics≥2.2m A uncovered/≤1m A covered-rising characteristics≤1m A uncovered/≥2.2m A covered-F ault message≤1m AN ecessary processing system NAMUR processing system according to IEC60947-5-6(EN50227/DIN19234)M odes(NAMUR output adjustable to falling or rising characteristics)-M in.rising characteristic curve(H igh current when immersed)-M ax.falling characteristics(L ow current when immersed)M easuring accuracyD eviation±1mm(0.04in)I nﬂuence of the process temperature on the switching point1S hifting of the switching point in mm(in)2P rocess temperature in°C(°F)3S witching point at reference conditions(notch)4T uning forkI nﬂuence of the product density on the switching point1S hifting of the switching point in mm(in)2P roduct density in g/cm³(lb/in³)3S witch position0.5g/cm³(0.018lb/in³)4S witch position0.7g/cm³(0.025lb/in³)5S witching point at reference conditions(notch) 6T uning fork 30115-EN-081119。

x_产品技术支持信息周报_(三月第四版).

x x 产品技术支持信息周报产品技术支持信息周报产品技术支持信息周报( ( (三月第三版三月第三版三月第三版【周报导读】一 .x3100M3 未知设备驱动;二 .x3620M3 如何安装内存;三 .x3650M3 如何安装光驱;四 .x3850X5 的 I/O 插槽;五 .x3850X5 如何安装 QPI 卡;六 .x3850x5 如何上机架;七 .CTO 如何做 x3950X5 ;八 .Open Fabric Manger 分几种版本;九 .智能直通模块网口对应关系; 十 .五款刀箱的区别; 【周报内容】一.x3100M3未知设备驱动?A:x3100M3的服务器如果安装windows系统,建议安装win2008 64bit,装完系统后系统下未知设备驱动链接如下:芯片组/support/entry/portal/docdisplay?lndocid=MIGR-5082466&brandind=5000008网卡/support/entry/portal/docdisplay?lndocid=MIGR-54793&brandind=5000008显卡/support/entry/portal/docdisplay?lndocid=MIGR-5083515&brandind=5000008二.x3620M3如何安装内存?A:一颗CPU的的内存安装顺序:3、6、8、2、5 和 7两颗CPU的的内存安装顺序:3、11、6、14、8、16、2、10、5、13、7 和 15 具体请参考x3620M3的用户手册。

x3620M3用户手册(69y4002_simplified_chinese.pdf这个是中文的:/support/entry/portal/docdisplay?lndocid=MIGR-5084233&brandind=5000008三.x3650M3如何安装光驱?A:x3650M3安装光驱需要打开机箱,找到光盘驱动器填充面板后部的蓝色松开卡口;然后在按住卡口的同时,将光盘驱动器填充面板推出驱动器托架。

TongFang Solder Paste TF225S-M305NI-D-885 TDS

同方科技
TONGFANG TECH
產品技術規格書
Product Technical Data Sheet
文件編號 TDS Code 制訂日期 Issued Date 修訂日期 Revised Date 頁碼頁數 Page Number
TF225S-M305NI-D-885 2015/10/31 2017/07/19 頁 Page 3/8
88.50
IPC-TM-650 2.2.20
170±30 Pa.S
Initial: 75.6 gm; Tack retention @ 24 hr: 120.2 gm; Tack retention @ 72 hr: 96 gm
JIS-Z-3284 6 @ Malcom PCU-205:10 rpm 3 min 25±1 ℃ <60% RH
IPC J-STD-004 IPC-TM-650 2.3.28.1 IPC-TM-650 2.3.32 IPC-TM-650 2.6.15
4.3 電氣性能 Electrical properties
表面絕緣阻抗 SIR
電遷移 Electromigration
Pass, Test Conditions: IPC 7 days @ 85°C 85% RH | Ordinary state 1x1012(Ω) or above After humidifying 1x 109(Ω) or above After 100hrs. in humidity
由同方公司研發的TF225S系列焊錫膏為客戶提供優良的可焊接性與印刷型。 TF225S系列焊錫膏解決了無鉛焊料在應用中出現的各種問題，如：儲存於運輸穩定性，潤濕性差以及由高溫焊料導致的錫膏不耐熱性

Power&存储产品技术支持信息周报 (2012九月第三版)

Power&存储产品技术支持信息周报 (九月第三版)【周报导读】一.7226-1U3的介绍；二.7226-1U3的物理参数介绍；三.7316-TF3切换器和线缆的配置；四.如何在e-config中选择7316-TF3；五.V7000U端口及连接；六.R06 路由功能在解决方案中的用法；七.N6210 e-config中常用许可配置(iSCSI，FCP，CIFS，NFS，FTP，HTTP)【周报详情】一.7226-1U3的介绍:解答：1、简介7226-1U3作为一款最新推出的媒体抽屉，代替了原来的7216-1U2(2012/04/27停产)。

可以通过SAS 接口、USB接口或者FC接口连接到Power6/POWER7以及IBM BladeCenter models PS700, PS701, PS702, PS703和PS704服务器。

7226-1U3可以连接两个磁带机，两个移动硬盘设备或者四个DVD光驱。

7226-1U3支持AIX、IBM i、Linux的操作系统，但是，USB设备不支持IBM i的操作系统。

目前，可用于7226-1U3的设备如下：DAT160 SAS Tape Drive (#5619)DAT160 USB Tape Drive (#EU16)Half-High LTO Ultrium 5 SAS Tape Drive (#8247)Half-High LTO Ultrium 5 Fibre Channel (FC) Tape Drive (#8248)DVD-RAM Sled w/1 DVD-RAM SAS Drive(#1420)DVD-RAM SAS Drive Only(#1422)DVD-RAM Sled w/1 DVD-RAM USB Drive(#5762)DVD-RAM USB Drive Only(#5757)RDX Removable Disk Drive Docking Station (#1103)320 GB Removable RDX Drive(#1708)500 GB Removable RDX Drive(#1107)1.0 TB Removable RDX Drive(#EU01)2、连接方式7226-1U3可以通过SAS接口、USB接口或者FC接口连接到Power6/POWER7以及IBM BladeCenter models PS700, PS701, PS702, PS703和PS704服务器。

Power&存储产品技术支持信息周报 (2012十二月第三版)

Power&存储产品技术支持信息周报 (十二月第三版)【周报导读】一.fc#5289串口卡与现有的fc#5785串口卡的区别；二.如何配置C/C++/Fortran/COBOL等语言编译器；三.5765-H23与5662-H23有什么区别,为什么5765-H23描述里有"1 Year SW Maint"字样；四.可以用IVM来激活Active Memory Expansion 吗；五.DS8870 e-Config中Drives的配置六.DS5100/DS5300 e-config中Exp.Attach选项配置七.N3200系列产品介绍【周报详情】一.fc#5289串口卡与fc#5785串口卡的区别:解答：fc#5289--2 Port Async EIA-232 PCIe Adapter是两口的串口卡，fc#5785--4 Port Async EIA-232 PCIe Adapter是四口的串口卡，他们的区别如下：fc#5289 的两个接口是RJ45的接口，而fc#5785的四个接口是9针的串口；因此c#5289在做串口心跳时，不能直接连接fc#3927或fc#3928的串口线，需要配置RJ45转9针串口的转换线fc#3930。

现在power710/720/730/740/750/770/780都可以订购fc#3930的转换线，如果客户需要配置fc#5289两口的串口卡时，务必配置fc#3930的转换线。

注：fc#5289和fc#5290都是两个RJ45口的串口卡，它们的区别在于fc#5289是full-height 的，fc#5290是low-profile的；它们实现的功能是一样的，fc#5289是插在full-height PCIe 的槽位上，fc#5290是插在low-profile PCIe的槽位上。

二.如何配置C/C++/Fortran/COBOL等语言编译器解答：双击"Software Products"打开软件配置窗口,将产品分类中的"Programming Languages"选中,"next"到产品选择窗口,根据需求选择相应的编译器产品即可三.5765-H23与5662-H23有什么区别,为什么5765-H23描述里有"1 Year SW Maint"字样:解答：5765-H23包括按照CPU数量的软件license和1年的软件免费服务,这里CPU的数量是服务器上需要使用PowerHA的分区总的处理器核数,可以少于整台服务器处理器核数。

FUJITSU Software Interstage XWand V13 产品说明书

Datasheet FUJITSU Software Interstage XWandDatasheetFUJITSU SoftwareInterstage XWand V13Interstage XWand is a complete solution for creating, validating, reading and enriching XBRL.Interstage XWand V13Interstage XWand V13 marks the first commercial implementation of the Table Linkbase specification, which has been adopted in new taxonomies provided by EBA and EIOPA. Interstage XWand V13 also includes the improved, high-performance Formula processor to handle large instance documents. This release provides application developers with more power and flexibility while providing the tools users greater usability and agility in working with XBRL.About Interstage XWandInterstage XWand is a complete solution that allows you to create, review, modify, validate and convert XBRL taxonomies and instances. Interstage XWand is for everyone –users wanting to start quickly working with XBRL through the packaged tools as well as application developers wanting to create XBRL based solutions through a rich API. Interstage XWand allows users to create business rules and multiple views of their XBRL documents and automatically manage changes. Interstage XWand facilitates organizations to make XBRL in integral part of their reporting process through:∙Support for the complete XBRL specification ∙Creating and viewing of Inline XBRL (including native support of upcoming ESMA filing requirements)∙Tagging of MS Excel and MS Word documents∙EDGAR Filer Manual, Global Filer Manual and ESMA Filer Manual validation∙High-performance Formula engine ∙Table Linkbase support∙business user-friendly XBRL reportcreation for all Table Linkbase-basedtaxonomies like those of EBA/EIOPA by GUItools and via auto-generated Excel forms –perfect alternative for T4U users.PRODUCT FEATURESGuranteeing XBRL ComplianceInterstage XWand V13 builds on thecapabilities of previous versions to extendits enviable reputation in complying with thelatest XBRL specification requirements.Interstage XWand V13 supports the TableLinkbase specification and provides data modelAPI that represents the rendered tablesaccording to the definition of Table Linkbase.Table Linkbase specification is built on theexisting XBRL specifications such asDimensions and Formula, which Interstage XWandcompletely supports from earlier versions;making our Table Linkbase implementation veryreliable.Adherence to Complex RulesInterstage XWand V13 provides high-performance Formula processor, which canprocess large instance documents. This allowsusers to define their own business rules tovalidate documents irrespective of complexityand size; ensuring complete adherence to theneeds of the regulators and the business.Interstage XWand V13 supports automatedvalidation based on the Global Filing Manual,which defines the common rules filers mustpass before submitting their reports.Interstage XWand V13 supports the latest EDGARFiler Manual rules, so companies can ensuretheir documents comply with the SEC'srequirements completely.Integration with Business SystemsThe powerful and robust XBRL processor and APIof Interstage XWand V13 are available for .NETand Java platforms; allowing organizations tofully integrate XBRL into their existingbusiness systems. It also allows softwarevendors to build fully compliant XBRLapplications.Cloud PlatformInterstage XWand ToolkitUsers can select from a complete range of XBRL tools which best suit their requirements. Windows 10, Windows 10 x64 – Pro or EnterpriseWindows 8.1 , Windows 8.1 x64 – Pro or EnterpriseWindows 7, Windows 7 x64 – Enterprise, Ultimate or ProfessionalInterstage XWand Application DeveloperAn Application Programming Interface (API) which allows organizations and solution providers to XBRL-enable applications in Java or .NET environments. Windows 10, Windows 10 x64 – Pro or EnterpriseWindows 8.1 , Windows 8.1 x64 – Pro or EnterpriseWindows 7, Windows 7 x64 – Enterprise, Ultimate or ProfessionalInterstage XWand RuntimeEnables applications developed using Interstage XWand Application Developer to be deployed to multi-user environments. Windows Server 2016 - Standard or Datacenter Edition Fujitsu Global Cloud Platform Windows Server 2012 R2 – Standard or Datacenter EditionOracle Solaris 11, 10Red Hat Enterprise Linux 7, 6, 5Datasheet FUJITSU Software Interstage XWandNEW IN XWAND V13XBRL REVIEW⏹ Easy XBRL report creation for Table Linkbase-based taxonomies like those ofEBA/EIOPA by GUI tools and Auto-generated Excel forms⏹ Taxonomy creation including Formula and Table Linkbase by integrated GUI tools ⏹ Performance improvement of the Formula processing for large instance documents ⏹ API for rendered table based on Table Linkbase definition ⏹ Support for the Global Filing Manual validationXBRL CREATION⏹ Best environment to reliably and completely create XBRL taxonomies and theirextensions including Dimensios, Formula, and Table Linkbase⏹ Enhanced support to create XBRL and Inline XBRL instances in full compliancewith the guidelines of the respective regulators⏹ Strong integration with the latest Microsoft Word and Microsoft Exceldocuments expedites and automates the largely repeatable creation of reports⏹ Customizable user interface gives users total control over the look & feel ofthe tools⏹ Powerful search, multiple views and customizablereports provide full XBRLaccess for the accountant, the financial report expert as well as the uninitiatedXBRL VALIDATION⏹ Check the form as well as content of the XBRL documents incorporating theXBRL 2.1, Dimensions and Inline XBRL specifications⏹ Use Formula for defining custom, business specific rules for validatinginstances⏹ Support for validating large instance documents⏹ Regulator specific validations including the EDGAR Filing Manual from the SEC(US)and the Inline XBRL Guidelines from the HMRC (UK)⏹ Support for compliance with best practices through the incorporation of FRTAand FRIS rules as well as the Global Filing Manual validation⏹ Additional support for creating custom validations through Fujitsu's own Querylanguage⏹ Support viewing of documents based on the schema order or one of the linkbases in a well-structured tabular format⏹ Allow users to review inline XBRL documents along with the detail information of taxonomies ⏹ Support for the SEC Previewer provides access to the regulator (SEC)- specified viewingguidelines⏹ Allow users to define and customize reporting views for transforming the XBRL documentsinto HTML and/or Excel spreadsheets⏹ Allow users to define their own custom filters and views of the documents using Fujitsu'spowerful Query interface⏹ Facilitate collaboration between users through the support of user comments to eachcomponent of XBRL dataUSER BENEFITS⏹ Novice and power users alike can create, extend and validate taxonomies and financialreports with a minimum of time and effort⏹ Users can easily create XBRL reports for EBA, EIOPA, or Table Linkbase-based taxonomiesby user friendly GUI tool supporting Excel import/export.⏹ Users can easily build a system or an application based on the Table Linkbase using APIthat represents rendered tables⏹ Business rules created with Formula ensure that reporting organizations can fully validatetheir documents, even if they are very large, before filing with full transparency and visibility into the rules⏹ Users can continue to create financial reports in a format (Microsoft Word and MicrosoftExcel) that they are familiar with and then automatically generate XBRL documents from these documents⏹ Organizations submitting filings can validate their filings against all the automatableSEC rules, the Inline XBRL guidelines for submissions to the HMRC, and the Global Filing Manual⏹ Users can automatically migrate their instances from previous filings and previoustaxonomies to the new regulatory taxonomies and extensions alike by utilizing VersioningIn addition to Interstage XWand, Fujitsu provides a range of platform solutions. They combine reliable Fujitsu products with the best in services, know-how and worldwide partnerships.Dynamic InfrastructuresWith the Fujitsu Dynamic Infrastructures approach, Fujitsu offers a full portfolio of IT products, solutions and services, ranging from clients to datacenter solutions, Managed Infrastructure and Infrastructure-as-a-Service.Software/software/⏹ Interstage: Application infrastructure softwareComputing products/global/services/computing/⏹ PRIMERGY: Industrial standard server ⏹ SPARC Enterprise: UNIX server⏹ PRIMEQUEST: Mission-critical IA server ⏹ ETERNUS: Storage systemLearn more about Interstage XWand, please contact your Fujitsu sales representative, Fujitsu business partner, or visit our website. /interstage/Fujitsu Green Policy Innovation is our worldwide project for reducing burdens on the environment. Using our global know-how, we aim to resolve issues of environmental energy efficiency through IT. Please find further information at: /global/about/environment/ContactCenter of Excellence for EMEA Region FQS Poland Ltd. (FUJITSU Group) Address: Parkowa 11 Street 30-538 Krakow, PolandEmail:***********Tel. (+48 12) 429 43 45Website: www.fqs.pl/en/finance/products© Copyright 2017 FUJITSU Limited. Fujitsu, the Fujitsu logo, Interstage, and XWand are trademarks or registeredtrademarks of Fujitsu Limited in Japan and other countries.XBRL is a trademark or service mark of XBRL International, Inc., registered in the United States and in other countries. Other company, product and service names may be trademarks or registered trademarks of their respective owners. Technical data is subject to modification and delivery is subject to availability. Any liability that the data and illustrations are complete, actual or correct is excluded. Designations may be trademarks and/or copyrights of the respective manufacturer, the use of which by third parties for their own purposes may infringe the rights of such owner.。

技术支持工程师周报总结

技术支持工程师周报总结一、本周工作概述本周我作为技术支持工程师，主要负责处理客户反馈的技术问题，并为公司内部的项目提供技术支持。

工作内容涵盖了软件系统故障排查、硬件设备维护以及与客户和团队成员的沟通协调。

二、软件系统故障处理在软件系统方面，我们接到了多个客户关于系统运行不稳定和功能异常的报告。

其中，客户名称 1反馈其使用的业务管理系统频繁出现卡顿和数据丢失的情况。

经过深入排查，发现是由于数据库中的部分索引损坏以及服务器内存资源不足导致。

我及时与运维团队协作，对数据库进行了修复和优化，并调整了服务器的内存分配策略，成功解决了该问题，确保系统恢复稳定运行。

另外，客户名称 2在使用我们新推出的移动应用时，遇到了登录失败和界面显示异常的问题。

通过对用户端和服务器端的日志分析，确定是由于新的版本更新中存在兼容性漏洞。

我们迅速组织开发团队进行紧急修复，并及时为客户推送了更新补丁，保证了客户能够正常使用该应用。

三、硬件设备维护硬件设备维护也是本周工作的重要组成部分。

客户名称 3的办公网络出现了频繁掉线的情况，影响了正常的工作效率。

我前往现场进行检测，发现是由于路由器老化和部分网线接口松动所致。

更换了新的路由器，并重新制作和固定了网线接口后，网络恢复了稳定，解决了客户的困扰。

此外，客户名称 4的服务器出现了硬盘故障的警报。

我第一时间协助客户备份了重要数据，并联系了硬件供应商更换了故障硬盘，重新配置了服务器的存储设置，确保了服务器能够正常运行，数据安全得到保障。

四、技术支持与协作在为公司内部项目提供技术支持方面，积极参与了项目名称 1的开发过程。

与开发团队紧密合作，对新功能进行了测试和评估，提出了一些优化建议，例如改进用户界面的交互设计，以提高用户体验。

同时，还参与了项目名称 2的上线前准备工作。

协助配置服务器环境，进行压力测试，确保系统能够在高并发的情况下稳定运行。

与项目团队的良好沟通和协作，有效推进了项目的进展，为项目的成功上线奠定了基础。

2024年公司岗位工作总结（六篇）

2024年公司岗位工作总结时光荏苒，转眼间，我已在公司服务数载。

自我入职以来，个人成长与工作能力均有了显著的提升。

在过去的年份里，我圆满完成了各项任务，实现了自身的价值。

随着新年的钟声敲响，新一年度的工作也已拉开序幕，我认为有必要对过去一年的工作进行梳理，以明确自身不足，为新一年的发展奠定坚实基础。

一、工作表现回顾在过去的一年中，我在工作上的表现可圈可点，对各项任务的处理已能做到得心应手。

二、工作不足与改进我也注意到自己在工作中仍存在一些不足。

例如，我容易受到外界干扰，无法将全部精力集中于工作，这有时会导致小的失误。

尽管我能够迅速纠正这些错误，但它们仍然对我的工作产生了一定影响。

为此，我计划在未来的工作中更加专注，努力克服这一弱点，以提升工作效率和个人能力。

我在完成每项工作后都会进行反思，旨在发现并改进自身的不足，确保持续进步。

我深知，要想将工作做到极致，必须投入更多的时间和精力，并不断提高自身素质。

虽然我在公司服务年限较长，但与优秀同事相比，仍有一定差距。

因此，我将以更加饱满的热情投入到新的工作中。

在过去的一年里，我在各个领域均取得了良好的成绩，工作能力也有了显著提升。

但我不会因此而沾沾自喜，我将保持目前的工作态度，争取在新的一年里取得更大的进步。

我要对同事和领导在过去一年中给予我的帮助和支持表示衷心的感谢。

在新的一年里，我将继续努力，以优异的成绩回报领导的期望。

2024年公司岗位工作总结（二）在履行运维工作职责的过程中，我们始终秉承精细化管理理念，严格按照既定计划执行日常运维任务。

一、全面细致地推进日常运维工作1. 自运维工作启动之初，信息技术部门的领导即寄予我们厚望，并提出了提升服务水平的明确要求。

____的稳健发展为宗旨，以对用户高度负责的态度，将“严把质量，服务至上”的原则融入日常运维工作的各个环节，从而显著提升了客户满意度，并多次获得用户认可。

2. 针对信息技术部门提出的新的工作要求与方案，我们迅速响应，坚持“严格要求”的原则，对提出的要求进行科学分析，及时制定周密的解决方案，并邀请用户试用或测试，确保运维工作的及时性与有效性。

技术质量周报格式

技术质量周报尊敬的者，本周的技术质量周报将为您带来最新的技术趋势与质量控制方面的重要内容。

是本报告的主要内容：一、技术趋势本周，我们将聚焦于最新的技术趋势，其中包括自动化、人工智能和物联网等领域的发展。

自动化在质量管理中扮演着越来越重要的角色，它可以高效率、减少人工错误，并确保质量。

人工智能和物联网的蓬勃发展对于各行业来说都是一大机遇，但同时也带来了新的技术挑战和风险，如数据隐私和安全性等方面的考虑。

我们将探讨如何在这些领域中保持技术质量和安全性。

二、质量控制本周，我们将重点关注质量控制方面的最新实践和策略。

在开发生命周期中，质量控制是确保最终产品符合预期标准的重要环节。

我们将一些质量控制的最佳实践，包括审查、回归和缺陷管理等方面的技术和方法。

我们还将探讨如何建立有效的质量度量体系，以监控和改进质量。

三、案例分析本周，我们将为您带来一些实际案例的分析，这些案例涉及到质量管理中的一些典型问和解决方案。

通过分析真实案例，我们可以更好地理解如何应对各种挑战，并从中汲取经验教训。

我们将探讨一些成功的案例，例如如何应对需求变更、如何有效地进行团队合作以及如何管理外包开发等方面的问。

四、专家观点本周，我们还将邀请来自业界的一些专家他们在技术质量领域的观点和经验。

他们将从不同的出发，他们对于技术趋势、质量控制和案例分析等方面的见解和建议。

通过专家的观点，我们可以更加全面地了解当前技术质量的状况和发展趋势。

五、者互动为了增加者的参与度，我们鼓励者在本周报下方留言区留下自己的想法和问。

我们将选取一些有代表性的留言，并在下期报告中进行回复和讨论。

通过者互动，我们可以更好地了解者的需求和关注点，并供更加贴近实际需求的内容。

我们希望本周的技术质量周报能够为您供有价值的信息和见解，并激发您对技术质量的思考和探索。

如果您对任何内容有疑问或建议，请随时与我们取得。

谢谢阅！技术质量周报编辑部敬上。

技术支持工程师周报报告范本

技术支持工程师周报报告范本周报日期：开始日期结束日期员工姓名：＿____部门：＿____一、本周工作内容（一）客户问题处理1、问题概述客户 A 反映其使用的软件在进行数据导入时出现错误，提示“文件格式不支持”。

客户 B 称系统运行缓慢，影响工作效率。

客户 C 遇到网络连接故障，无法访问公司内部资源。

2、处理过程对于客户 A 的问题，首先检查了导入的文件格式，发现其与软件要求的格式存在差异。

指导客户将文件转换为正确的格式后，成功完成数据导入。

针对客户 B 系统运行缓慢的情况，远程登录其电脑进行系统性能检测。

发现后台存在多个占用大量资源的进程，关闭不必要的进程并优化系统设置后，系统运行速度明显提升。

对于客户 C 的网络连接问题，通过排查网络配置和路由器设置，发现是 DNS 服务器配置错误。

更正 DNS 服务器地址后，网络连接恢复正常。

（二）系统维护与优化1、服务器巡检对公司的服务器进行了定期巡检，包括硬件状态检查、系统日志分析等。

未发现硬件故障，但在系统日志中发现了一些潜在的安全风险警告，已及时采取措施进行防范。

2、软件更新与补丁安装对公司使用的关键软件进行了更新，并安装了最新的安全补丁，以确保系统的稳定性和安全性。

3、性能优化针对部分员工反映的办公软件响应速度慢的问题，对相关软件的配置进行了优化，提高了软件的运行效率。

（三）新需求评估与方案制定1、需求收集与业务部门进行沟通，收集了关于系统功能改进的新需求，包括增加报表生成功能、优化用户界面等。

2、评估与分析对收集到的需求进行了详细的评估和分析，考虑了技术可行性、实施难度、对现有系统的影响等因素。

3、方案制定根据评估结果，制定了初步的技术方案，并与相关部门进行了讨论和确认。

二、本周遇到的问题及解决方案（一）技术难题1、在处理客户 A 的数据导入问题时，遇到了一种罕见的文件格式解析错误。

经过查阅大量技术文档和在线资源，最终找到了一个开源的文件格式转换工具，解决了问题。