Model 710底标签打印机说明书
合集下载
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
• Latch the printhead and ensure the liner is threaded through the gap sensor.
• Slide the printer forward to until it latches.
• Close the printer door to operate the unit.
Printer Latch
Locking Clip
Takeup Spool
SupplySpool
CLOSE OPEN
NOTICE
PROPERTY DAMAGE Do not spray or wash down. Disconnect all power to this unit before cleaning. Follow the cleaning instructions detailed in the manual.
Loading Labels
• Press the label roll onto the supply spool.
• Hold down on the printer latch and slide the printer to the left.
• Unlatch the printhead by pulling the printhead support first right and down and then lower printhead.
The Model 710 is a bottom label printer and applicator that allows placing nonmarketing type information on the bottom of a wrapped tray. Information such as Safe Handling Information, Nutrition Facts, Country of Origin Labeling, and bar code pricing that take up space on a label can be moved to the bottom of the package allowing more of the product to be seen by the consumer.
• Thread the liner up and back into the printhead, then onto the takeup spool. Secure the liner with the locking clip.
• Advance the liner until a label is visible at the eject end of the printhead.
• Thread the label liner up as shown with the liner coming off of the roll to the right side.
• Insert the labels into the rear of the printer making sure the labels are fed between the gap sensor.
Access Door
Power Switch
Use a dampened clean cloth to clean the surfaces
of the Model 710.
Printhead Latch
Do not directly spray the unit.
Open the Access Door for access to label supply.
Model 710 Bottom Label Printer and Applicator OperatNING
ELECTRICAL SHOCK HAZARD Disconnect all power to this unit before cleaning or servicing.
©2012 METTLERTOLEDO P/N: 17185200A R01
Label Specifications
Width: 57mm, 64mm, 80mm Length: 61mm to 107 mm (2.4” to 4.2”)
Cleaning
Use a clean cloth dampened with warm water to wipe the exterior surfaces. Do not spray liquids directly on the unit. Do not use solvents or cleaners on the unit.
• Slide the printer forward to until it latches.
• Close the printer door to operate the unit.
Printer Latch
Locking Clip
Takeup Spool
SupplySpool
CLOSE OPEN
NOTICE
PROPERTY DAMAGE Do not spray or wash down. Disconnect all power to this unit before cleaning. Follow the cleaning instructions detailed in the manual.
Loading Labels
• Press the label roll onto the supply spool.
• Hold down on the printer latch and slide the printer to the left.
• Unlatch the printhead by pulling the printhead support first right and down and then lower printhead.
The Model 710 is a bottom label printer and applicator that allows placing nonmarketing type information on the bottom of a wrapped tray. Information such as Safe Handling Information, Nutrition Facts, Country of Origin Labeling, and bar code pricing that take up space on a label can be moved to the bottom of the package allowing more of the product to be seen by the consumer.
• Thread the liner up and back into the printhead, then onto the takeup spool. Secure the liner with the locking clip.
• Advance the liner until a label is visible at the eject end of the printhead.
• Thread the label liner up as shown with the liner coming off of the roll to the right side.
• Insert the labels into the rear of the printer making sure the labels are fed between the gap sensor.
Access Door
Power Switch
Use a dampened clean cloth to clean the surfaces
of the Model 710.
Printhead Latch
Do not directly spray the unit.
Open the Access Door for access to label supply.
Model 710 Bottom Label Printer and Applicator OperatNING
ELECTRICAL SHOCK HAZARD Disconnect all power to this unit before cleaning or servicing.
©2012 METTLERTOLEDO P/N: 17185200A R01
Label Specifications
Width: 57mm, 64mm, 80mm Length: 61mm to 107 mm (2.4” to 4.2”)
Cleaning
Use a clean cloth dampened with warm water to wipe the exterior surfaces. Do not spray liquids directly on the unit. Do not use solvents or cleaners on the unit.