最全的压铸模具相关英语注释.
压铸模具与成型专业名词(中英文版)
常用软件推荐(Common software recommendation)
Flow 3D / Pro cast Software（US）-目前国内小压铸厂比较多用，因为是免费软件。 Small die casting plant is more commonly used, because it is a free software. Magma-software（Germany）-汽配件大型压铸厂信赖的软件。 This software trusted by large automobile parts company for die casting. Any-casting （Korea）-国内小型压铸厂用的多些。 It was made in Korea, it was more used in the small die casting plant in China.
氮 碳 共 渗 是 在 含 有 活 性 碳 、 氮 原 子 的 介 质 中 同 时 渗 入 氮 和 碳 ， 并 以 渗 氮 为 主 的 低 温 氮 碳 共 渗 工 艺 （ 530℃580℃）。氮碳共渗的渗层脆性小，共渗时间比渗氮时间大为缩短。压铸模经氮碳共渗后，可显著提高其热疲劳性 能。
电镀涂层- Electroplating Coating
Item 1: 模具结构 . Die and Mold
• Prepared by : Danny • Date: 2024-1月
压铸模具零件结构-Mold components.
✓ 前模固定板 Cavity Fixing Plate/ A Plate
✓ 料套 Sprue Bush
模具安装在压铸机上。 Tooling fixed in the die casting machine.
模具专业术语英文
注塑、模具专业英语Surface Appearance外观Glossiness/gloss finish光洁度、粗糙度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface玻纤外露、浮纤Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹、料花Flow mark流纹Brittle/brittleness脆、脆性Bubbles/trapped gas气泡/困气Void孔、气泡Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃等级V-2Poor dispersion分散不好FR/PTFE …agglomerates etc阻燃剂/PTFE…结块Pellet porous颗粒料孔隙、Low impact/tensile strength etc低冲击强度/拉伸强度等High flow/filler content etc高流动性/过度填充Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles纤维结团Product was rejected due to 产品不能接受因为…High moisture level高水分、高湿度Warpage/warped翘曲/变形Shrinkage/shrink收缩/收缩率Sink marks凹陷、缩水Short shot/short molding打不满、欠注Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边、披锋、溢边Discoloration变色Off color颜色差异Flow rate流动速率Viscous/viscosity粘性的、粘的/黏度High flow高流动Low flow低流动Sticky粘的，粘性的Sticking core粘后模，粘模芯Sticking sprue粘水口Sticking cavity粘前模Mold release（agent）脱模(剂)Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in extra …添加多一点…Reduced …content减少…含量Dropped/reduced …by x％减少…含量…％Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption预计年/月用量模具方面：Ejection system顶出系统、脱模系统pin顶针、推杆spring弹簧Gate type浇口类型Sprue主流道runner分流道cavity模腔Sprue gate直浇口Pin point gate点浇口Tab gate护耳浇口Fan gate 扇形浇口Tunnel or submarine gate潜伏式浇口Jump gate跳跃式浇口Diaphragm gate片状浇口Ring gate 环形浇口The cavity of the mould模腔Heated cylinder加热料筒Surface finish表面光洁度Sink mark缩水Air trap困气Gas trapped气体困着，困气void空隙，孔galling烧焦Weld line熔接痕，熔合线Drag mark划伤、脱模痕Scratch mark模具刮花Deformed/ warp变形Ejector not returned顶针不回位slide滑块、行位streak波纹、条纹、色痕delamination分层Jetting mark喷射痕Gate mark浇口痕rib筋、加强筋、骨位boss凸台、凸起、凸痕Melt flow length熔体流线长度Ejector plate顶针板Stop pin限位销Push rod推杆、顶针Push back pin复位杆Ejector guide pin顶针导柱Cold-slug-well冷料井、冷料穴plate模板Ejected mark顶痕，顶白nozzle喷嘴Surface defect表面缺陷Air vent排气口Filling uneven走胶不平衡、进胶不平衡pressure:压力speed:速度control:控制protection pressure:保压mold:模set:设定option:选择injection:射胶pressure reducing valve :减压阀relief valve:泄压阀max:最大max:最大system:系统proportional:比例pressure transducer:压力传感器sampling试模pressure sensor压力感应器AMP 伺服放大器trial runrunninggatedosage 溶胶clamp open 开模。
模具英文术语精编版
根据国家标准，以下为部分塑料模具成形术语的标准翻译。
动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具术语的标准翻译。
压力铸造模具 Die-Casting Die压铸模零部件定模 Fixed Die Cover Die定模座板 Fixed Clamping Plate定模套板 Bolster Fixed Die动模 Moving Die Ejector Die动模座板 Moving Clamping Plate直流道 Sprue横流道 Runner内浇口 Gate模具分类Injection Mold 注塑模Plastic Rubber Mould 塑胶模Rubber Molding 橡胶成形Hot Chamber Die Casting 热室压铸Sand Mold Casting 砂模铸造Extrusion Mold 挤出模Multi-Cavity Mold 多模穴模具Stack Mold, Stack Injection Mould 叠层模Plaster Mold 石膏模Three Plates Mold 三板模Plain Die 简易模Pierce Die 冲孔模Forming Die 成型模Progressive Die 连续模Gang Dies 复合模Shearing Die 剪边模Cavity Die 型腔模Riveting Die 铆合模Compression Molding 压缩成型Flash Mold 溢流式模具Extrusion Mold 挤压式模具Split Mold 分割式模具Mould Cavity 型腔母模Mold Core 模芯公模Large Die Mold 大型模具Precise Die Mold 精密模具Complex Die Mold 复杂模具Foaming Mould 发泡模具Metal Die 金属模具Plastic Mold 塑料模具Press Tool Stamping Die Punch Die 冲压模具Extrusion Die 挤压模具Graphite Die 石墨模具流道浇口部分Runner System 浇道系统Sprue Cold Material Trap 浇道冷料井Sprue Puller 拉杆Runner Design 流道设计Main Runner 主流道Secondary Runner 次流道Mould Gate Design 浇口设计Submarine Gate 潜伏浇口Tunnel Gate 隧道式浇口Pinpoint Gate 点浇口Fan Gate 扇形浇口Side Gate 侧浇口Edge Gate 侧缘浇口Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口Dish Gate 盘形浇口Diaphragm Gate 隔膜浇口Ring Gate 环形浇口Runnerless 无浇道Sprueless 无射料管方式Long Nozzle 延长喷嘴方式Sprue 浇口，溶渣Insulated Runner Hot Runner 热浇道Runner Plat 浇道模块Valve Gate阀门浇口Slag Well 冷料井Cold Slag 冷料渣Sprue Gate 射料浇口，直浇口Nozzle 射嘴Sprue Lock Pin 料头钩销（拉料杆）注塑缺陷Flash 飞边Warpage 翘曲Air Trap 积风Blush 发赤Flow Line 流痕Splay 银纹Short Shot 短射Sink Mark 缩痕Streak 条纹Void 缩孔Weld Line 熔接线Gas Mark 烧焦Cold Slug 冷斑Delamination 起皮Burr 毛刺Flaw Scratch 刮伤Gloss 光泽Glazing 光滑Surface Check 表面裂痕Hesitation 迟滞注塑工艺Molding Conditions 成型条件Drying 烘干Barrel Temperature 料筒温度Melt Temperature 熔化温度Mold Temperature 模具温度Injection Pressure 注塑压力Back Pressure 背压Injection Speed 注塑速度Screw Speed 螺杆转速Tensile Strength 抗拉强度Tensile Elongation 延伸率Flexural Modulus 弯曲模数Flexural Strength 抗弯强度Shrinkage 收缩率Regrind Usage 次料使用Moulding 模塑机械设备Lathe 车床Planer 刨床Miller Milling Machine 铣床Grinder 磨床Driller 钻床Linear Cutting 线切割Electrical Sparkle 电火花Welder 电焊机Punching Machine 冲床Robot 机械手Common Equipment 常用设备EDM Electron Discharge Machining 放电加工3D Coordinate Measurement 三次元量床Boring Machine 搪孔机Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Cylindrical Grinding Machine 外圆磨床Die Spotting Machine 合模机Engraving Machine 雕刻机Engraving E.D.M 雕模放置加工机Form Grinding Machine 成形磨床, Graphite Machine 石墨加工机Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床模具零件Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具<, /SPAN> Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具常用之工作机械3D Coordinate Measurement 三次元量床Boring Machine 搪孔机CNC Milling Machine CNC铣床Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Copy Lathe 仿形车床Copy Milling Machine 仿形铣床Copy Shaping Machine 仿形刨床Cylindrical Grinding Machine 外圆磨床Die Spotting Machine 合模机Drilling Machine 钻孔机Engraving Machine 雕刻机Engraving E.D.M 雕模放置加工机Form Grinding Machine 成形磨床Graphite Machine 石墨加工机Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床Jig Boring Machine 冶具搪孔机Jig Grinding Machine 冶具磨床Lap Machine 研磨机Machine Center 加工制造中心Multi Model Miller 靠磨铣床NC Drilling Machine NC钻床NC Grinding Machine NC磨床NC Lathe NC车床NC Programming System NC程式制作系统Planer 龙门刨床Profile Grinding Machine 投影磨床Projection Grinder 投影磨床Radial Drilling Machine 旋臂钻床Shaper 牛头刨床Surface Grinder 平面磨床Try Machine 试模机Turret Lathe 转塔车床Universal Tool Grinding Machine 万能工具磨床Vertical Machine Center 立式加工制造中心Wire E.D.M 线割放电加工机入水 Gate进入位 Gate Location水口形式 Gate Type大水口 Edge Gate细水口 Pin-point Gate水口大小 Gate Size转水口 Switching Runner Gate唧嘴口径 Sprue Diameter流道 Mold Runner热流道 Hot Runner Hot Manifold温度控制器温控器 Thermostat Thermoregulators Temperature Controller热嘴冷流道 Hot Sprue Cold Runner唧嘴直流 Direct Sprue Gate圆形流道 Round Full Half Runner流道电脑分析 Mold Flow Analysis流道平衡 Runner Balance热嘴 Hot Sprue热流道板 Hot Manifold发热管 Cartridge Heater探针 Thermocouples插头 Connector Plug插座 Connector Socket密封封料 Seal运水 Water Line喉塞 Line Plug Throat Taps喉管 Tube塑胶管 Plastic Tube快速接头 Jiffy Quick Connector Quick Disconnect Coupling 模具零件 Mold Components三板模 3-Plate Mold二板模 2-Plate Mold边钉导边 Leader Pin Guide Pin边司导套 Bushing Guide Bushing中托司 Shoulder Guide Bushing中托边 Guide Pin顶针板 Ejector Retainner Plate托板 Support Plate螺丝 Screw管钉 Dowel Pin开模槽 Ply Bar Scot内模管位 Core Cavity inter-Lock顶针 Ejector Pin司筒 Ejector Sleeve司筒针 Ejector Pin推板 Eject Plate Push Plate Stripper Plate缩呵 Movable Core Return Core Puller扣机（尼龙拉勾） Nylon Latch Lock斜顶 Lifter模胚（架） Mold Base上内模 Cavity Insert下内模 Core Insert行位（滑块） Slide镶件 Insert压座 Wedge耐磨板油板 Wedge Wear Plate压条 Plate撑头 Support Pillar唧嘴 Sprue Bushing挡板 Stop Plate定位圈 Locating Ring锁扣 Latch扣机 Parting Lock Set推杆 Push Bar栓打螺丝 S.H.S.B顶板 Ejector Plate活动臂 Lever Arm分流锥 Sprue Spreader分流板 Spreader Plate水口司 Bush垃圾钉 Stop Pin隔片 Buffle弹弓柱 Spring Rod弹弓 Die Spring中托司 Ejector Guide Bush中托边 Ejector Guide Pin镶针 Pin销子 Dowel Pin波子弹弓 Ball catch喉塞 Pipe Plug锁模块 Lock Plate斜顶 Angle from Pin斜顶杆 Angle Ejector Rod尼龙拉勾 Parting Locks活动臂 Lever Arm复位键提前回杆 Early Return Bar气阀 Valves斜导边 Angle Pin术语 Terms承压平面平衡 Parting Surface Support Balance模排气 Parting Line Venting回针碰料位 Return Pin and Cavity Interference顶针碰运水 Water Line Interferes with Ejector Pin 料位出上下模 Part from Cavith （Core） Side不准用镶件 Do Not Use （Core Cavity） Insert用铍铜做镶件 Use Beryllium Copper Insert初步模图设计 Preliminary Mold Design正式模图设计 Final Mold Design弹弓压缩量 Spring Compressed length稳定性好 Good Stability Stable强度不够 Insufficient Rigidity均匀冷却 Even Cooling扣模 Sticking热膨胀 Thermal Expansion公差 Tolerance铜公（电极） Copper ElectrodeAir Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流挡板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom Board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting Lug 铸耳Cavity 模腔模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Joint Pipe Coupler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Inserts 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton Frameworks 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道残料顶销浇道推出杆Sprue Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板Pierce 冲孔Forming 成型（抽凸冲凸）Draw Hole 抽孔Bending 折弯Trim 切边Emboss 凸点Dome 凸圆Semi-Shearing 半剪Stamp Mark 冲记号Deburr or Coin 压毛边Punch Riveting 冲压铆合Side Stretch 侧冲压平Reel Stretch 卷圆压平Groove 压线Blanking 下料Stamp Letter 冲字（料号）Shearing 剪断Tick-Mark Nearside 正面压印Tick-Mark Farside 反面压印Extension Drawing 展开图procedure Drawing 工程图Die Structure Drawing 模具结构图Material 材质Material Thickness 料片厚度Factor 系数Upward 向上Downward 向下Press Specification 冲床规格Die Height Range 适用模高Die Height 闭模高度Burr 毛边Gap 间隙Weight 重量Total Weight 总重量Punch Weight 上模重量Compression Molding 压缩成型Flash Mold 溢流式模具Extrusion Mold 挤压式模具Split Mold 分割式模具Cavity 型腔母模Mold Core 模芯公模Taper 锥拔Leather Cloak 仿皮革Shiver 饰纹Flow Mark 流痕Welding Mark 溶合痕Post Screw Insert 螺纹套筒埋值Self Tapping Screw 自攻螺丝Striper Plate 脱料板Piston 活塞Cylinder 汽缸套Chip 细碎物Handle Mold 手持式模具Encapsulation Molding 低压封装成型Two Plate 两极式（模具）Well Type 蓄料井Insulated Runner 绝缘浇道方式Hot Runner 热浇道Runner Plat 浇道模块Valve Gate 阀门浇口Band Heater 环带状的电热器Spindle 阀针Spear Head 刨尖头Slag Well 冷料井Cold Slag 冷料渣Air Vent 排气道Welding Line 熔合痕Eject Pin 顶出针Knock Pin 顶出销Return Pin 回位销反顶针Sleeve 套筒Stripper Plate 脱料板Insert Core 放置入子Runner Stripper Plate 浇道脱料板Guide Pin 导销Eject Rod （Bar）（成型机）顶业捧Subzero 深冷处理Three Plate 三极式模具Runner System 浇道系统Stress Crack 应力电裂Orientation 定向Sprue Gate 射料浇口，直浇口Nozzle 射嘴Sprue Lock Pin 料头钩销（拉料杆）Slag Well 冷料井Side Gate 侧浇口Edge Gate 侧缘浇口Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口Fan Gate 扇形浇口Dish Gate 因盘形浇口Diaphragm Gate 隔膜浇口Ring Gate 环形浇口Submarine Gate 潜入式浇口Tunnel Gate 隧道式浇口Pin Gate 针点浇口Runnerless 无浇道Sprueless 无射料管方式Long Nozzle 延长喷嘴方式Sprue 浇口溶渣Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合式模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Bending Die 双折冷弯模具偏移弯曲模Extrusion Die 挤出模Palletizing Die 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runnerless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow（Blow） Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Barreling 滚光加工Belling 压凸加工Bending 弯曲加工Blanking 下料加工Bulging 撑压加工Burring 冲缘加工Cam Die Bending 凸轮弯曲加工Caulking 压合加工Coining 压印加工Compressing 压缩加工Compression Bending 押弯曲加工Crowning 凸面加工Curl Bending 卷边弯曲加工Curling 卷曲加工Cutting 切削加工Dinking 切断蕊骨Double Shearing 叠板裁断Drawing 引伸加工Drawing with Ironing 抽引光滑加工Embossing 浮花压制加工Extrusion 挤制加工Filing 锉削加工Fine Blanking 精密下料加工Finish Blanking 光制下料加工Finishing 精整加工Flanging 凸缘加工Folding 折边弯曲加工Folding 折叠加工Forming 成形加工Impact Extrusion 冲击挤压加工Indenting 压痕加工Ironing 引缩加工Knurling 滚花Lock Seaming 固定接合Louvering 百叶窗板加工MarKing 刻印加工Necking 颈缩加工Notching 冲口加工Parting 分断加工Piercing 冲孔加工Progressive Bending 连续弯曲加工Progressive Blanking 连续下料加工Progressive Drawing 连续引伸加工Progressive Forming 连续成形加工Reaming 铰孔加工Restriking 二次精冲加工矫形锻压Riveting 铆接加工Roll Bending 滚筒弯曲加工Roll Finishing 滚压加工Rolling 压延加工Roughing 粗加工Scrapless Machining 无废料加工Seaming 折弯重叠加工Shaving 缺口修整加工Shearing 切断加工Sizing 精压加工矫正加工Slitting 割缝加工Spinning 卷边旋接Staking 铆固Stamping 锻压加工Swaging 挤锻压加工Trimming 整缘加工Upsetting 锻粗加工顶锻镦粗Wiring 抽线加工Aberration 色差Atomization 雾化Bank Mark 料垄迹印Bite 咬入Blacking Hole 涂料孔（铸疵）Blacking Scab 涂料疤Blister 起泡Blooming 起霜Blow Hole 破孔Blushing 泛白Body Wrinkle 侧壁皱纹Breaking-in 冒口带肉Bubble 膜泡Burn Mark 糊斑Flash Burr 毛边Camber Warpage 翘曲Cell 气泡Center Buckle 表面中部波皱Check 细裂痕Checking 龟裂Chipping 修整表面缺陷Clamp-off 铸件凹痕Collapse 塌陷Color Mottle 色斑Corrosion 腐蚀Crackle 裂痕裂纹Crazing 碎裂Crazing 龟裂Distortion Deformation 变形Edge 切边碎片Edge Crack 裂边Fading 退色Filler Speak 填充料斑Fissure 裂纹Flange Wrinkle 凸缘起皱Flaw 刮伤Flow Mark 流痕Galling 毛边Glazing 光滑Gloss 光泽Grease Pits 污斑Grinding Defect 磨痕Haircrack 发裂Haze 雾度Incrustation 水锈Indentation 压痕Internal Porosity 内部气孔Mismatch 偏模Mottle 斑点Necking 缩颈Nick 割痕Orange peel 橘皮状表面缺陷Overflow 溢流Peeling 剥离Pit 坑Pitting Corrosion 点状腐蚀Plate Mark 模板印痕Pock 麻点Pock Mark 痘斑Resin Streak 树脂流纹Resin Wear 树脂脱落Riding 凹陷Sagging 松垂Saponification 皂化Scar 疤痕Scrap 废料Scrap Jam 废料阻塞Scratch 刮伤划痕Scuffing 深冲表面划伤Seam 裂痕Shock Line 模口挤痕Short Shot 充填不足Shrinkage Pool 凹孔Sink Mark 凹痕Skin Inclusion 表皮折叠Straightening 矫直Streak 条状痕Surface Check 表面裂痕Surface Roughening 橘皮状表皮皱折Surging 波动Sweat Out 冒汗Torsion Distortion 扭曲Warpage 翘曲Waviness 波痕Webbing 熔塌Weld Mark 焊痕Whitening 白化Wrinkle 皱纹Gas Aassisted Technology 气辅Bottle Cap Mold 瓶盖模具。
压铸专业英语
模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 扥架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴扥板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧销goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶镦冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢襯套knockout bar 脫模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料销spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 扥板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 钻孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程序制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机检验量测工具用语autocollimator 自动准直机bench comparator 比长仪block gauge 块规bore check 精密小测定器calibration 校准caliper gauge 卡规check gauge 校对规clearance gauge 间隙规clinoretee 测斜仪comparator 比测仪cylinder square 圆筒直尺depth gauge 测深规dial indicator 针盘指示表dial snap gauge 卡规digital micrometer 数位式测微计feeler gauge 测隙规gauge plate 量规定位板height gauge 测高规inside calipers 内卡钳inside micrometer 内分厘卡interferometer 干涉仪leveling block 平台limit gauge 限规micrometer 测微计mil 千分之一吋monometer 压力计morse taper gauge 莫氏锥度量规nonius 游标卡尺optical flat 光学平晶optical parallel 光学平行passimeter 内径仪position scale 位置刻度profile projector 轮廓光学投影仪protractor 分角器radius 半径ring gauge 环规sine bar 正弦量规snap gauge 卡模square master 直角尺stylus 触针telescopic gauge 伸缩性量规working gauge 工作量规模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板表面处理关连用语age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿扥木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理焊接用语acetylene 乙炔ampere 电流安培angle welding 角焊arc 电弧argon arc welding 氩弧焊接bare electrode 光熔接条butt welding 对接焊接camber 电弧弯曲cascade 阶迭熔接法clad weld 被覆熔接crator 焊疤excess metal 多余金属filler rod 焊条fillet weld 填角焊接gas shield 气体遮蔽groove welding 起槽熔接hand face shield 手握面罩hard facing 硬表面堆焊jig welding 工模焊接laser beam welding 雷射光焊接metal electrode insert gas welding MIG熔接nugget 点焊熔核overlaying 堆焊peening of welding 珠击熔接法plug welding 塞孔熔接positioned welding 正向熔接pressure welding 压焊propane gas cutting 丙烷气切割pure nickel electrode 纯镍熔接条reinforcement of weld 加强焊接resist 抗蚀护膜root running 背面熔接seam 焊缝seaming 接合seam welding 流缝熔接series seam welding 串联缝熔接skip welding process 跳焊法spark 火花spot welding 点焊接stitch welding 针角焊接stud arc welding 电弧焊接under laying 下部焊层void 焊接空隙weld flow mark 焊接流痕weld flush 焊缝凸起weld line 焊接纹weld mark 焊接痕weld penetration 熔接透入weld zone 焊接区welding 焊接welding bead 焊接泡welding direction 焊接方向welding distortion 焊接变形welding flux 焊剂welding ground 电熔接地welding interval 焊接周期welding stress 熔接应变welding torch 熔接气炬射出成形关联用语activator 活化剂bag moulding 气胎施压成形bonding strength 黏合强度breathing 排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 着色剂color matching 调色color masterbatch 色母料compound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度儀daylight 開隙dry cycle time 空料試車週期時間ductility 延性elastomer 弹性体extruded bead sealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floating platen 活动模板foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injection plunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 后固化premix 预混料purging 清除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑料片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率塑料原料acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CA cellulose acetate butyrate 醋酸丁酸纤维素CAB composite material 复合材料cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑料epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetate copolymer 乙烯-醋酸乙烯EV A ethylene-vinlacetate copolyme 醋酸乙烯共聚物EV A expanded polystyrene 发泡聚苯乙烯EPS fiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MF nitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑料polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PA polybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POM polyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPO polypropylene 聚丙烯PP polystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PU polyvinylacetate 聚醋酸乙烯PV AC polyvinylalcohol 聚乙烯醇PV A polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物silicone resin 硅树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑料unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差atomization 霚化bank mark 滞料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹模具常用刀具与工作法用语adjustable spanner 活动扳手angle cutter 角铣刀anvil 铁钻arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手计算机关联用语3D modeling 三次元模拟access 通路animation 卡通影片application 应用board 基板bug 故障bus 总线CAD 计算机辅助设计CAE 计算机辅助工程分析CAM 计算机辅助制造cassette 卡座color display 彩色显示器command 指令communication 通信compact 精简小型computer 计算机copy 复制cursor 游标curve modeling 曲面仿真database 数据库design 设计digitizing 数字化disk 磁盘dot 点eyelet 眼孔floppy 磁盘片format 格式化graphic 圆解hardware 硬件honeycomb 蜂巢interface 界面know how 秘诀laser printer 激光打印机lay out 布置memory 记忆memory swap 交换记忆microprocessor 微处理器modeling 造型module 模块monitor 屏幕mouse 鼠标need 需求network 网络new version 新版on line 上线中option 选择PC 个人计算机plotter 绘图机program 程序scanning 扫描simulation 仿真software 软件solid model 实体模型system 系统tape 磁带terminal 终端机texture 构造trim 修边venter 排气风扇word processor 文书处理器各种冲模加工关连用语barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工caulking 铆合加工coining 压印加工compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 迭板裁断drawing 引伸加工drawing with ironing 抽引光滑加工embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 精密下料加工finish blanking 光制下料加工finishing 精整加工flanging 凸缘加工folding 折边弯曲加工folding 折迭加工forming 成形加工impact extrusion 冲击挤压加工indenting 压痕加工ironing 引缩加工knurling 滚花lock seaming 固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工notching 冲口加工parting 分断加工piercing 冲孔加工progressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工reaming 铰孔加工restriking 二次精冲加工riveting 铆接加工roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工scrapless machining 无废料加工seaming 折弯重迭加工shaving 缺口修整加工shearing 切断加工sizing 精压加工/矫正加工slitting 割缝加工spinning 卷边铆接staking 铆固stamping 锻压加工swaging 挤锻压加工trimming 整缘加工upsetting 锻粗加工wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车buckle 剥砂面camlachie cramp 铸包casting on flat 铆合chamotte sand 烧磨砂charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼后熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部level 水平loader 供料器unloader 卸料机loop controller 闭回路控制器lower die 下模micro inching device 微寸动装置microinching equipment 微动装置motor 马达moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床seamless forging 无缝锻造separate 分离shave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slide balancer 滑动平衡器slug hole 逃料孔spin forming machine 旋压成形机spotting 合模stack feeder 堆栈拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程take out device 取料装置toggle press 肘杆式压力机transfer 传送transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机vibration feeder 振动送料机wiring press 嵌线卷边机线切割放电加工关连用语abnormal glow 不规则辉光放电arc discharge 电弧放电belt 皮带centreless 无心chrome bronze 铭铜clearance angle 后角corner shear drop 直角压陷deflection 桡曲度discharge energy 放电能量dressing 修整dwell 保压flange 凸缘gap 间隙graphite 石墨graphite contraction allowance 电极缩小余量graphite holder 电极夹座hair crack 发裂horn 电极臂jump 跳刀magnetic base 磁性座master graphite 标准电极pipe graphite 管状电极pulse 脉冲rib working 肋部加工roller electrode 滚轮式电极rotary surface 旋转面shank 柄部sharp edge 锐角部tough bronze 韧铜traverse 摇臂tungsten bronze 钨青铜waviness 波形起伏work 工件working allowance 加工余量working dischard 加工废料锻铸造关连用语accretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace 酸性平炉aerator 松砂机air set mold 常温自硬铸模airless blasting cleaning 离心喷光all core molding 集合式铸模all round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand 背砂base bullion 粗金属锭base permeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔board drop hammer 板落锤bottom pour mold 底浇bottom pouring 底注boxless mold 脱箱砂模break-off core 缩颈砂心brick molding 砌箱造模法buckle 剥砂面camber 错箱camlachie cramp 铸包cast blade 铸造叶片casting flange 铸造凸缘casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂core template 砂心模板core vent 砂蕊排气孔corner gate 压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔die approach 模口角度draw out 锻造拔长draw plate 起模板draw spike 起模长针dummying 预锻embedded core 加装砂心erosion 冲砂fettling 铸件清理filling core 埋入砂心filling in 填砂film play 液面花纹finishing slag 炼后熔渣flash gutter 锻模飞边槽flask molding 砂箱造模forging roll 辊锻机formboard 进模口板gutter 锻模飞边槽hammer man 锻工heading machine 顶镦机impacter 卧式锻造机inblock cast 整体铸造ingot 铸锭ingot blank 铸坯inlay casting 镶铸法investment casting 失模铸造isothermal forging 恒温锻造loose piece 木模活块molding pit 铸模地坑pouring process 浇注法recasting 重铸roll forging 轧锻rolled surface 轧制表面rough sand 粗砂roughing forge 粗锻sand crushing 塌箱seamless forging 无缝锻造separate 分离shave 崩砂shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slag 熔渣slag inclusion 夹渣stickness 黏模性strip layout 带状胚料排样法tap casting 顶注top gate 顶注浇口unworked casting 不加工铸件upender 翻转装置upending 顶锻uphill casting 底铸white cast iron 白口铸件模具加工方法barrel 滚筒(加工) bending 波纹加工broaching 拉刀切削centering 定中心cutting 切削cylindrical lathe cutting 外圆车削electric discharge machine 放电加工electrolytic grinding 电解研磨embossing 压花加工facing 面车削filing 锉刀修润hand finishing 手工修润hemming 卷边加工hobbing 滚齿加工joggling 摇动加工lapping 抛光/研磨修润laser beam machining 雷射加工lathe cutting 车床车削planning 刨削加工polishing 抛亮光reaming 铰孔修润rough machining 粗切削rounding 圆形加工sawing 锯削scaling 清除钢碇缺陷shaping 成形加工skiving 表面研磨slotting 切缝切削taper turning 锥度车削thread cutting 螺纹切削ultrasonic machining 超音波加工up cut milling 逆铣加工学理实验与试验用语air permeability test 透气性试验austenitic steel 沃斯田铁钢brinell hardness 布耐内尔硬度brinell hardness test 布氏硬度试验charpy impact test 夏比冲击试验conical cup test 圆锥杯突试验cup flow test 杯模式流动度试验dart drop impact test 落锤冲击试验Elmendorf test 埃罗门多撕裂强度试验environmental stress cracking test 环境应力龟裂试验ericessen test 埃留伸薄板拉伸试验falling ball impact test 落球冲击试验fatigue test 疲劳试验ferrite 纯铁体gantt chart 甘特图heat cycle test 热循环试验histogram 柱状图hot bend test 热弯试验izod impact test 埃左德冲击试验loop tenacity 环结强度martens heat distortion temperature test 马顿斯耐热试验martensite 马氏体mullen bursting strength tester 密廉式破裂强度试验机nol ring test 诺尔环试验normal distribution 常态分配ozone resistance test 抗臭氧试验pareto diagram 柏拉图peeling test 剥离试验pinhole test 针孔试验机rattler test 磨耗试验rockweel hardness test 洛氏硬度试验rockweel hardness 洛氏威尔硬度rolinx process 罗林克斯射出压缩成形法rossi-peakes flow test 罗西皮克斯流动试验sampling inspection 抽样检查scratch hardness 抗刮硬度shore hardness 萧氏硬度spiral flow test 螺旋流动试验surface abrasion test 表面磨耗试验taber abraser 泰伯磨耗试验机tensile impact test 拉伸冲击试验tensile strength 抗拉强度tension test 张力试验thermal shock test 冷热剧变试验torsion test 扭曲试验ubbelohde viscometer 乌别洛德黏度计vicat indentation test 维卡针压陷试验Vickers hardness test 维氏硬度试验warpage test 翘曲试验weatherometer 人工老化试验机weissenberg effect 威森伯格回转效应砂轮用语abrasive 砂轮Al2O3 氧化铝balance 平衡bond 结合borazon 氧化硼立方晶buffing wheel 抛光布轮diamond 钻石dresser 砂轮整修机dressing 修整endless grinding belt 循环式研磨带finishing allowance 加工余量grain 磨粒grinding disc 研磨盘jamp up 孔眼堵塞mesh 网筛目parameter 参数resinoid grinding wheel 半树脂型砂轮slitting 切缝量vitrified 陶瓷的wheel 旋转机械设计及周边其它用语assembly drawing 装配图auto tool change cycle 自动换刀时间周期beam 横梁bending moment 弯矩bending stress 弯曲应力bottoming 底靠buckling 纵弯曲chamfering 去角斜切channel 凹槽chattering 颤动check point 查核点chip 切屑chip conveyor 排屑输送机coefficient of friction 摩擦系数compact 小型的cooling pipe 冷却管coupon 试样胚deflection 挠曲量distortion 扭曲变形draft taper 拔模锥度draw out 拉拔fit tolerance 配合公差flexible rigidity 弯曲刚性gas vent 气孔hatching 剖面线heater cooler 加热器冷却装置hook cavity 钩穴inching 寸动lug 凸缘maintenance 维修保固metallurgy 冶金学notch effect 切口效果out of roughness 真圆度performance 动作性能pit 坑plane strain 倒角应力plug mill 蕊棒轧管机repeated load 重复载荷riveted joint 铆钉接合sand paper 砂纸shift 偏移shrink fit 热压配合shrinkage hole 缩孔sinking 凹陷sketch 草图spalling 剥落straightness 直度submarine 深陷式surface roughness 表面粗度tapping 攻螺丝thermocouple 热电耦torsion load 扭转载荷toughness 韧性tracing 描图under cut 凹割业务与贸易关连用语accept order 接受订货account 账户after service 售后服务amendment 修正annual sales 年销售额at sight 见票即付balance 余额bank draft 汇票bargain goods 廉价品batch 批次bid 出价bid sales 投标买卖bill of landing 提单bills receivable 应收票据brand 品牌bulk cargo 散装货business transaction 商业交易buyer 买方carbon copy 打字副本cargo collection 揽货carton 纸箱cash in advance 预付现金catalogue 型录cheque 支票CLF 运费保险费在内价格claim 索赔clearance goods 清仓品commision 佣金commission 批发商complain 抱怨container 货柜correspondence bank 往来银行cost 成本cost and freight; C&F 含运费价格custom broker 报关行customer 客户D/A 承兑交单D/P 付款交单deferred payment 分期付款deferred shipment 分期装运delivery on spot 当场交货delivery time 交期delivery order 交货单discount 折扣discount on draft 贴现documentary draft 跟单汇票down payment 订金enclosure 附件endorsement 背书enquete 调查exhibition 展览会export 出口factory visiy 工厂参观favourable price 合宜价格foreign exchange 外汇free on board 船上交货价idea price 希望价格import 进口Japanese Industrial 日本工业规格invoice 发票L/C 信用状margin 利润market 市价net weight 净重no payment 拒绝付款odd item 零头offer 报价open account 交互计算order 订单over looked 疏漏packing 包装pamphlet 小册子partial shipment 分批装船patent 专利paying price 合算价格payment method 付款方式port of destination 目地港port of trans-shipment 转口港price 价格price decending 减价price rising 涨价procurement 采办prompt delivery 实时交货purchase 购入purchasing agent 采购代理商quotation 报价单rebate 回扣reference 查询remittance 汇款repeat order 追加订货request letter 请求函rumor 风评second hand goods 二手货shipper 货主shipping 装船shipping mark 麦头shipment 出货sold out 卖完sole agent 总代理商special discount 特别折扣specification 规格sample order 指样订货standing 信用情形storage charge 仓租subcontract 外包subject to final confirmation 有待确认之报价supplier 供货商T/T 电汇tie-in sale 搭售trade fair 商展会trans-shipment 转运transferred 已转运wharf 码头A3D coordinate measurement 三次元量床3D modeling 三次元模拟aberration 色差abnormal glow 不规则辉光放电abrasive 砂轮access 通路account 账户accretion 炉瘤accurate die casting 精密压铸acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnance 酸性平炉activator 活化剂acetylene 乙炔。
压铸及机械英语词汇汇编
压铸及机械英语词汇(2009-09-01 20:11:44)压铸及机械词汇A 安装尺寸 install dimension 凹模固定板 retainer plate凹模 female die, female mold, negative moldB 备件 spare parts变质 modification变质剂 modification agent扒渣 slagging-off保温炉 holding furnace保压压力 dwell pressure表面缺陷 surface defectC 淬火硬度quenching hardness抽芯core侧面抽芯side core抽芯油缸core oil cylinder插拔式结构plug抽芯机构core puller抽芯油缸支架bracket of cylinder粗糙度roughness/degree铸件表面粗糙度surface roughness擦伤galling尺寸公差dimension tolerance of casting除气degassing吹气净化blow purifying除气剂degassing flux出渣de-slagging出渣口slag hole沉渣sludge出炉口tap hole菜花头Cauli-flowering超声波检验ultrasonic test重熔re-meltingD 端盖cover动模垫块spacer parallel锻钢 forged steel氮化处理nitriding treatment断裂fracture塑性断裂plastic fracture导柱guide pillar导套guide sleeve导向板guide plate导向件guide part动型moving die/ejector die/movable mould动模座板moving clamp plate/bottom clamping plate 定模座板fixed clamp plate/top plate定型fixed die/cover die定模套版bolster/fixed die顶杆ejector pin顶出结构ejector mechanism顶出ejector吊装孔lifting eye吊环lifting ring镀钛处理titanium plating treatment多肉缺陷metallic projection电火花electric spark打磨grindingF 分流锥 divider/blast cone分型面 mold parting/parting face/mold joint附页 attachment/appendix复位杆 reset bar(rod)附件故障 accessory覆盖剂 covering flux废金属料scrap浮渣cinder反射炉 reverberatory furnace废品 reject飞边joint flash仿真simulationG 规格 specification/standard数值孔径 numerical aperture (N.A)固定段 segment坩埚crucible坩埚炉crucible furnace感应电炉electric induction furnace沟槽 blind scab硅SiliconH 滑块 sliding block滑块部件 moving parts滑块退让 return/move back焊补 welding-on横浇道 runner合模 die locking横流道 runner回炉料foundry returns合型 mold assembling/closing/die locking合型力 die locking force化学成分不合格chemical consistence analysisJ 浇口套 sprue bush浇排道系统pouring system浇不足 misrun浇注 pouring浇注断裂interrupted pour浇道比 gating ratio浇包 ladle精整dressing and finishing精度 accuracy接口 connector击伤 shot damage金相组织 metallographic structure金属残液heel金相检验metallographic test金属型涂料 die coating/coating for metal mold 加压速度 rate of pressure increasing间隙 clearance精炼refining精炼剂refining flux精密铸造 precision casting静置holding/stewing渗透 impregnation集渣装置dirt traps夹杂类缺陷inclusion defects夹渣entrapped slag/slag inclusion夹具 tool fixturesK 壳体 housing开炉 blowing in孔洞缺陷cavity库存 inventoryL 冷却 cooling冷却水管 cooling water pipe冷却耐压管 cooling pressure pipe冷却水管用密封圈 O-ring/sealing ring/gasket ring冷室卧式压铸机 horizontal (cold chamber) die casting machine 冷却系统 cooling system冷却水接口 cooling water connector冷裂 cold crack冷隔 cold lap铝 Aluminum裂纹 crack拉伤 caught casting拉杆孔 draw bar螺纹 screw/thread螺纹结构 screw structure螺纹公称直径(直径 diameter)公称尺寸(名义尺寸) specified size/nominal dimension漏油 leakage of oil棱边倒角 edge炉料 charge炉衬 furnace lining炉气分析flue gas analysis炉前分析on-the-spot sample analysis流痕 bloom/flow line力学性能不合格 physical-mechanical characteristic abnormalM 毛坯 rough/blank毛坯铸件 rough casting毛刺 veining/burr模芯 core模框 frame模槽 mold channel模套 chase/bolster/frame模具钢 die steel模具图纸 mold drawing内浇口 in-gate冒口 riser/feeder head冒口浇注系统 feeder head gating system镁 Magnesium锰 Manganese密闭耐压系统 tightness testN 内浇道 in-gate镍 NickleP 配油盘 pressure plate排气块 exhaust block排气槽 air vent排气孔 vent/venting channel排气塞 venting plug配合套圆形:fitting sleeve 方型: fitting case 跑铝 aluminum slop out of mold喷射冶金 injecting metallurgy喷丸清理 shot blasting cleaning抛丸清理 wheel blasting cleaning偏析 segregation破坏性实验 destructive testQ 取件机 extractor去除浇冒口 de-gating清铲 chipping缺陷铸件 defecting casting气孔 blowhole/gas cavity/pinhole/porosity气孔缩 blowhole shrinkage去毛刺 de-burring去除氧化皮 de-scaling氢 Hydrogen清理 cleaningR 热处理 heat treatment热电偶测温孔 thermocouple well热电偶 thermocouple (TC)/pyod热裂 hot heating熔炼 smelting熔化率 melting rate熔炼损耗 total melting loss熔池 bath熔剂 flux熔渣 slagS 水管 water pipe三维造型 3 D三坐标测量仪 coordinate 3上模座板 upper clamping plate缩孔 shrinkage缩松 dispersed shrinkage疏松 porosity(dispersed shrinkage)渗漏 leakage缩陷 sink/sink in/depression试块 test block/test piece/coupon实时控制系统 real-time control system 试模 de-buggingT 推板 push plate推杆 push rod推板导柱 push plate guide pillar推板导套 push plate guide sleeve凸模固定板 punch-retainer plate铜 copper钛 TitaniumW 网状裂纹 craze crack/crazing/checking 未浇满 poured shortX 型芯 core型腔 mold cavity镶拼处 splicing place斜导柱孔 hole of inclined guide pillar楔紧块 wedge型芯弯曲 core bending下模座板 lowering clamping plate型芯固定板 core-retainer plateX 光射线检验 X-ray inspectionY 压铸机 die casting machine压室 pressure chamber压室止口(定位)尺寸 dimension/size压实 squeezing compaction压射 shot/injection压射冲头 injection piston(ram)/plunger压铸型 die casting die压力铸造模具 die-casting die易损镶块 wear insert易损件 wearing parts预应力 pre-stress永久型 permanent mold硬点 hard spot溢流槽 over flow well印痕 indentation氧 Oxygen荧光检验 fluorescent testZ 真空接口 vacuum connector真空排气管 vacuum exhaust block总接头 main connector中接头 middle connector直浇道 sprue转接处(转口)transit装配图(铸型装配图) mold assembly drawing 铸钢 cast steel支架 ejector housing/mold base leg造渣 slag forming真空熔炼 vacuum melting真空压铸 vacuum die casting/ evacuated die casting 增压 pressurization针孔 pinhole沾铝 adhesive aluminum直读光谱分析仪 direct-reading spectrograph转运包 transfer ladle转向器steering rack柴油式传动叉车 Diesel forklift复印机 copying machine服务器 Server绘图仪 Graphic plotter兼容机 compatible machine材料库 warehouse投影仪 projector半自动车床 semi-automatic lathe半自动立式钻床 drill machine表面粗度测量仪 surface roughness gauge布洛维硬度计 Brinell hardness gauge测氢仪 Hydrogen gauge叉车充电机 charger程控交换机 exchanger齿轮油泵 oil pump储气罐 accumulator tank电动葫芦 Gantry crane电动试压泵 press tester电动斜切机 bias cutter电子秤 weighing scale电子扫描仪 scanner吊斗 spoon hopper高压离心风机 combustion blower管道泵 process water pump烘箱 oven监控系统 monitoring system简易数控车床 digital lathe交流弧焊机 Are welder抛光机 polisher锯床 saw空压机 air compressor冷冻式干燥机 dryer红外线测温仪冷却塔 cooling tower立式带锯床 band saw滤油机 oil filter焊接机 welder模温机 die heater喷粉室回收设备 painter system平面磨床 grinder气动量仪 air gauge切割机 cut-off machine清洗机 washer散热器攻丝机 tapping machine台式光谱仪 spectrograph台式砂轮机 abrasive machine卧式液压拉床 broaching machine铣床 milling machine钻床 drilling machine液压机 hydraulic machine真空机 vacuum pump时效炉 aging furnace电阻炉 stress relief furnace探伤机 diagnostic machine加工中心 machining center车床 lathe钻削中心 drilling & cutting center别克 Buick切边机 trim press冷却塔循环泵 cooling tower pump循环水离心泵 process water pump脱模剂压送机 die lube station取件机 extractorFL充痒压铸系统 FL oxygen feed die cast system 装卸车 loader在建工程 construction in progress捡漏机 picker纸芯式滤油器paper element filter电磁阀 solenoid valve溢流阀spillover valve调速阀 speed control valve压力传感器pressure transducer三角带wedge shaped belt节流阀throttle governor同步齿型带timing belt喷涂机spray coater轴承(main) bearing浮球阀 float valve/ball cock行车bridge crane平衡重式叉车counter balanced forklift轮毂螺栓wheel hub bolt制动蹄片brake shoe制动液braking fluid叶片lamina/vane侧护板side guard plate单列向心推力球轴承single row radial thrust ball bearing 带防尘盖单列轴承single row bearing shielded急停按钮 scram button三相开关threephase switch行程开关limit/travel switch断路器circuit breaker接触器 contactor中间继电器intermediate relay时间继电器 time relay控制变压器control transformer开关电源switching supply节能灯energy-saving lamp日光灯管fluorescent tube自整流高压汞灯泡self-rectifying high pressure mercury lamp 电工胶布garrers/electrical tape焊条welding rod石笔slate pencil外圆磨床external grinderHydraulic fluid oil 液压油Safety hook/bolts 安全钩Crosshead 十字头Tail stock 尾架尾座Frame cover 护板框盖Toggle top cover 肘环顶Coupling 联轴器Tie-bar 拉杆, 系杆Control panel 控制面板Power board 分配板, 配电板Overhauling 大修, 拆修Hose 软管, 水龙带Warranty period 保修期Nozzle 管口, 喷嘴Nature tan 日晒后的颜色, 茶色Electric fitting 电装、Rubber pad 橡胶垫Shock absorbing rubber stopper 减震橡皮塞Die height 模子闭合高度Die stroke 动模行程Intensification ratio standard 增强比标准Plunger stroke 柱塞行程Plunger tip penetration 冲头穿透力Viscosity index 粘度指数Rated pressure 额定压力Plug socket 插口, 塞孔Ventilated 通风的Anchor bolt hole 地锚(脚)螺栓孔Inlet 入口Galvanize 通电流Carbon grain 碳粒Mortar 火泥, 砂浆Stretcher 拉伸机Earthing cable 接地电缆Manifold 总管, 集合管Clamp force sensor 夹紧力传感器Attenuate 削弱Emulsification 乳化作用中子线wire for sliding出模斜度 draft angle隔皮 bur掉肉 misrun研配 grindTurbidity 浑浊度Refract meter 折光仪Sediment 沉淀物Glycol 乙二醇Combustible 易燃的Water-soluble 水溶性的Grease pump 黄油泵，油脂泵Drooling 滴料Disulfide 二硫化物Lithium 锂Gauge cock 试水位旋塞Pressure match valve 压力拟合阀Lock/check nut 防松螺母Slant 倾斜Core sliding face 型芯滑面Flux treatment 熔剂处理Die clamping cylinder 模具夹紧气缸Clogging 堵塞，闭合Electrode bar 电极棒Fumigation certificate 熏蒸消毒证书Crate 条板箱，柳条箱Resin parts 树脂零件Oil ring 油环Gear box 齿轮箱，传动箱,变速箱Draft angle 出模斜度Tap and drill gauge 丝锥及钻头规Tap borer 螺纹底孔钻Tap cutter 丝锥刀具Tap die holder 丝锥板牙两用夹头Tap handle 丝锥扳手Screw funnel 分液漏斗Screw chasing machine 螺纹切削机Screw cutting 螺纹切削Screw pitch gauge 螺距规Screw rivet 螺纹铆钉Screw vent 螺杆通孔Rack housing 齿条罩Rack Tubes 油缸Cup Seals Feed Pipes 输油管Spools 卷轴Recuperating Seal(恢复性密封) Inflator Tubes 充气.Cut Seals Steering Hoses 转向胶管Biscuit thickness 料柄厚度注油孔 oil filter point牛皮纸 kraft/brown paper瓦楞纸 fluting paper崩料 charge downslide/collapse 卡涉现象 interference phenomenon 机械加工余量 stocking复制模 replaced mould偏心距 offset distance抽大缸 pull tie bar料头 biscuit抽芯 loose core光整平滑度 flatnessDrain cock 排气阀，放出开关Wrench 扳手Stopper 塞子，制动器Intensifier 增强器Check valve 止回阀Orifice 孔，口Pilot valve 领示阀，导阀Cold shut 冷疤，冷结Flow mark 波纹，流线谱Shot stroke 压射冲程Surge pressure 冲击压力，脉动压力Jack bolt 定位螺栓Anchor hole 锚栓孔Dust seal 档尘圈Valve cover 气门盖，阀盖Cylinder tube 汽缸筒Piston rod 活塞杆Piston ring 活塞环Shot cylinder 压射缸Wire clamp 钢丝钳Air hose 空气软管，送风管Atomizer 喷雾器Strainer 滤网Hollow shaft 空心轴，管轴Potentiometer 电位计，分压计Shaft 轴，杆状物Asbestos wire 石棉线Pulley 滑车，滑轮Spring washer 弹簧垫圈Inverter 电源交换器Cutting fluid 切削液refraction coefficient 折光系数Screw Cutting Tap 螺旋切削丝锥plug gauge 塞规color shade色泽red lead power 红丹粉stress relief 去应力casting film 铸型薄膜cast form铸造成形, 铸型cast house crane炉前[出铁场]吊车cast panel铸造面板cast rotor铸造转子cast superalloy铸造高温合金cast test block铸造试块[棒]casting character铸造性能casting crack缩裂casting fin铸件飞边, 铸件披缝, 铸件周缘翅片casting head浇冒口casting lap铸件皱纹casting scar铸疤, 浇注疤casting sealer铸件渗补剂casting strain铸造应变casting stress铸造应力spark plug 火花塞internal-combustion engine cylinder内燃机汽缸hydraulics 水力学pinion小齿轮pinion bearing小齿轮轴承pinion cage主动[行星]齿轮架, 差速器壳, 差速盘pinion cutting machine齿轴切削机床pinion head齿轴齿顶pinion shaped cutter插齿刀pinion spider差速器十字轴pinion stop(起动机的)齿轮停止器valve housing阀套valve actuating mechanism配气机构valve air relief自动放气阀valve bank阀组valve barrel阀缸valve body attachment阀体连接头valve bounce阀跳valve bush阀衬, 阀[衬]套valve chest gasket阀柜垫密片valve cock阀栓valve cottar气阀制销valve disc阀盘valve discharge centrifuge活门卸料式离心机valve follower阀推杆valve positioner阀门定位器分层Delaminationfilling-engine梳丝机器filling agent 填充剂;填料filling auger装载螺旋filling compoun填料filling funnel注液漏斗车架 (car) frame钣金 sheet metal测板 side plate内侧板Inner side plate焊钳soldering turret焊条 welding rod焊点 welding spot焊接机器人 welding robot寿命周期成本 life cycle cost前轴 fore/leading axle后翼子板 rear fender切削性能 cutting characteristic散热性能 heat dispersion耐磨性能 wear resistant property摩擦系数 friction coefficient灰铸铁 gray iron; graphitic cast iron过盈配合 tight/interference fit缸套 cylinder, sleeve, barrel tube pipe 导轨面 guide way (face)铣刀盘 face milling cutter/facing cutter 刀盘 tool pan/cutter head磨削余量 grinding allowance耐用性 endurance钝化 passivation刀尖圆弧 circular profile of knife point (刀具)主偏角 entering angle; plan angle 弹性变形量 amount of elastic deformation 燃烧室 combustion chamber磨屑 abrasive dust滤器芯 strainer core差速器 differential gear反冲减震器 recoiling shock absorber废气涡轮 exhaust turbine涡轮增压器 turbocharger增压盲区 turboloch喷油器 oil sprayer/atomizer汽化器 carburetor硬质合金刀具 carbide tipped tool精镗刀具 fine boring tool动力传动系统 power transmission system spanner 扳子 (美作:wrench)double-ended spanner 双头扳子adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子 (美作:socket wrenchcalipers 卡规pincers, tongs 夹钳wire cutters 剪线钳multipurpose pliers, universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规hacksaw 钢锯grease gun 注油枪oil can 油壶边刨床 side planer插床 slotting machine车刀 lathe tool车轮车床 car wheel lathe车削 turningBayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Belt drive 带传动Bending machines 弯曲机Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Crimping tools 卷边工具Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Etching machines 蚀刻机Honing machines 搪磨机Lapping machines 精研机Milling heads 铣头Mold polishing/texturing 模具打磨/磨纹Planing machines 刨床aberration 色差atomization 雾化bank mark 料纹bite 咬入blacking hole 涂料孔(铸疵)blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡centre buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷colour mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹表面处理关联用语时效硬化 age hardening气体硬化 air hardening空气韧化 air patterning退火 annealing阳极效应 anode effect阳极氧化处理 anodizing滚镀 barrel plating滚筒打光 barrel tumbling染黑法 blackening青熟脆性 blue shortness碳酸盐薄膜防锈法 bonderizing箱位退火 box annealing封箱渗碳 box carburizing辉面电镀 bright electroplating光辉热处理 bright heat treatment 旁路热处理 bypass heat treatment 化学电镀 chemical plating化学蒸镀 chemical vapor deposition 大气热处理 controlled atmosphere 锐角效应 corner effect儒缓放电 creeping discharge压花 embossing部分淬火 selective quenching。
压铸业专业术语(英语)
文案大全Assembly line 组装线 Layout 布置图Conveyer 流水线物料板 Rivet table 拉钉机 Rivet gun 拉钉枪 Screw driver 起子Electric screw driver 电动起子 Pneumatic screw driver 气动起子 worktable 工作桌 OOBA 开箱检查fit together 组装在一起 fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板 barcode 条码barcode scanner 条码扫描器 fuse together 熔合 fuse machine 热熔机 repair 修理 operator 作业员 QC 品管supervisor 课长 ME 制造工程师 MT 制造生技cosmetic inspect 外观检查 inner parts inspect 内部检查 thumb screw 大头螺丝 lbs. inch 镑、英寸front plate 前板traightener 整平机punching machine 冲床 robot 机械手 hydraulic 液压 rear plate 后板 chassis 基座 bezel panel 面板power button 电源按键 reset button 重置键Hi-pot test of SPS 高源高压测试 Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件 plastic parts 塑胶件 SOP 制造作业程序material check list 物料检查表 work cell 工作间 trolley 台车 carton 纸箱 sub-line 支线 left fork 叉车personnel resource department 人力资源部production department 生产部门 planning department 企划部 QC Section 品管科stamping factory 冲压厂 painting factory 烤漆厂 common equipment 常用设备 uncoiler and s machine 油压机 lathe 车床planer |'plein|刨床 miller 铣床 grinder 磨床 driller??床linear cutting 线切割 electrical sparkle 电火花 welder 电焊机staker=reviting machine 铆合机 position 职务 president 董事长general manager 总经理special assistant manager 特助 factory director 厂长 department director 部长deputy manager | =vice manager 副理section supervisor 课长deputy section supervisor =vice section superisor 副课长 group leader/supervisor 组长 line supervisor 线长 assistant manager 助理to move, to carry, to handle 搬运 be put in storage 入库 pack packing 包装 to apply oil 擦油 final inspection 终检 to connect material 接料 to reverse material 翻料 wet station 沾湿台 Tiana 天那水cleaning cloth 抹布 tname of a department 部门名称 a o load material 上料 to unload material 卸料to return material/stock to 退料 scraped |'skræpid|报废 scrape ..v.刮;削deficient purchase 来料不良 manufacture procedure 制程 deficient manufacturing procedure 制程不良oxidation |' ksi'dein|氧化scratch 刮伤 dents 压痕defective upsiding down 抽芽不良 defective to staking 铆合不良 embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力 education and training 教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓 dministration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screwhead螺丝滑头slipped screwhead/shippery screwthread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterpriseexpansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-gradeproducts良品defective products, notup-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模文案大全to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified 不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---tothrow--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece,block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具文案大全figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap 切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetorysecond count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting departmentfor reference会计部存查end-user/using unit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventorylist will be sent to accountingdepartment together (Those of NHKwill be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records ofyear-end physical inventory Listandphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering moldtesting工程试模材料not included in physicalinventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by /prepared by核准/审核/承办PCE assembly production schedulesheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明文案大全part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts 不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆文案大全edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）文案大全top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口文案大全H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection新品首件检查FAA first article assurance 首件确认TVR tool verification report模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process模具制程能力参数SSQA standardized supplierquality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment品质机能展开FMEA failure modeleffectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output QualityLevel 平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece InspectionReport 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control统计制程管制SQC Statistical Quality Control统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management文案大全全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original EquipmentManufacture 原设备制造PCE Personal Computer Enclosure个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States ofAmerica 美国文案大全A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumerelectronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance策略品质保证DQA Desigh Quality Assurance设计品质保证MQA Manufacture QualityAssurance 制造品质保证SSQA Sales and service QualityAssurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic MagnetionInspect 高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll OxideSemiconductor 互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line Memory Module双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report改善报告NG Not Good 不良WPR Weekly Delivery Requirement周出货要求PPM Parts Per Million 百万分之一文案大全TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material Condition MMS Maximum Material SizeLMC Least Material Condition LMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形 rotaryforging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形 rubber molding橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形 shellcasting 壳模铸造foam forming ?泡成形sinterforging 烧结锻造forging roll 轧锻six sidesforging 六面锻造gravity casting 重力铸造slushmolding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfermolding 转送成形injection molding 射出成形 warmforging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landedplunger mold 有肩柱塞式模具burnishing die 挤光模landedpositive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具 manifolddie 分歧管模具counter punch 反凸模modularmold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswtbending die 双折冷弯模具extrusion die 挤出模 palletizingdie 叠层模family mold 反套制品模具 plastermold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具 pressuredie 压紧模fishtail die 鱼尾形模具 profiledie 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protablemold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavitymold 单腔模具solid forging die 整体锻模 splitforging die 拼合锻模split mold 双并式模具 spruelessmold 无注道残料模具squeezing die 挤压模stretch文案大全form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流档板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 托架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coilspring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢diaphragmgate 盘形浇口die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆drivebearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin顶出梢ejector plate 顶出板 ejector rod顶出杆ejector sleeve 顶出衬套 ejectorvalve 顶出阀eye bolt 环首螺栓 filling core椿入蕊film gate 薄膜形浇口 finger pin指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧?goose neck 鹅颈管 guide bushing引导衬套guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶?冲头headlesspunch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injectionram 压射柱塞inlay busher 嵌入衬套innerplunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockoutbar 脱模杵land 合模平坦面 land area 合模面leader busher 导梢衬套liftingpin 起模顶?lining 内衬locating centerpunch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush活动衬套making die 打印冲子manifoldblock 歧管档块master plate 靠模样板matchplate 分型板mold base 塑胶模座 mold clamp 铸模紧固夹mold platen 模用板movingbolster 换模保持装置moving bolster plate 可动侧模板文案大全。
压铸模具术语中英文对照
压铸模具英文对照压力铸造：die casting压铸模具：die-casting die定模：fixed die动模：moving die型腔：cavity分型面：parting line投影面积：project area收缩率：shrinkage锁模力：locking force压力中心：pressure centre充填速度：filling velocity压射速度：injection speed压射比压：injection pressure脱模斜度：draft闭合高度：die shut height最大开距：maximum opening daylight脱模距：stripper distance浇注系统：casting system直浇道：sprue横浇道：runner内浇口：gate溢流槽：overflow well排气槽：air vent定模座板：clamping plate of the fixed half 动模座板：clamping plate of the moving half 定模套板：bolster of the fixed half动模套板：bolster of the moving half支承板：support plat垫块：space block支承柱：support pillar型芯：core活动型芯：movable core螺纹型芯：threaded plug螺纹型环：threaded ring镶块：die insert定模镶块：die insert of the fixed half动模镶块：die insert of the moving half活动镶块：movable insert拼块：split斜销：angle pin弯销：angular cam滑块：slide 型芯滑块：core slide斜滑块：angled sliding split斜槽导板：finger guide plate限位块：stop block楔紧块：wedge block滑块导板：slide guide plate耐磨板：wear pad浇口套：sprue bush分流锥：sprue spreader导流块：baffle排气塞：venting plug排气板：venting plate导柱：guide pillar带头导柱：headed guide pillar带肩导柱：shouldered guide pillar矩形导柱：square guide pillar推板导柱：ejector guide pillar导套：guide bush直导套：straight guide bush带头导套：headed guide bush推板导套：ejector guide bush导板：guide plate推杆：ejector pin圆柱头推杆：ejector pin with a cylindrical head带肩推杆：shouldered ejector pin扁推杆：plat ejector pin成型推杆：forming ejector pin推管：ejector sleecve带肩推管：shouldered ejector sleeve推块：ejector pad推件板：stipping plate推杆固定板：ejector retaining plate推板：ejector plate限位钉：stop pin连接推杆：ejector tie rod推板连接推杆：ejector plate tie rod推板垫圈：ejector plate washer定位元件：locating element冷却环：cooling ring拉料杆：sprue puller pin隔流板：plug bffe。
最全的模具英语专业术语（超级实用）
最全的模具英语专业术语（超级实用）模具专业英语出模: mould unloading, mold stripping 出模角 : Draft Angle 出模方向: The direction of the mold Mold Parting Direction 入水： gate 进入位：gate location水口形式： gate type 大水口： edge gate细水口： pin-point gate 水口大小： gate size转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner流道电脑分析：mold flow analysis 流道平衡: runner balance 热嘴： hot sprue 热流道板： hot manifold发热管： cartridge heater 探针: thermocouples插头： connector plug 插座： connector socket密封/封料： seal三、运水：water line喉塞： line lpug 喉管： tube塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模： 3-plate mold 二板模： 2-plate mold边钉/导边：l eader pin/guide pin 边司/导套： bushing/guide bushing 中托司： shoulder guide bushing 中托边L： guide pin 顶针板： ejector retainner plate 托板： support plate螺丝： screw 管钉： dowel pin开模槽： ply bar scot 内模管位： core/cavity inter-lock顶针： ejector pin 司筒： ejector sleeve司筒针： ejector pin 推板： stripper plate缩呵： movable core,return core core puller扣机（尼龙拉勾）： nylon latch lock 斜顶： lifter模胚（架）： mold base 上内模： cavity insert下内模： core insert 行位（滑块）： slide镶件： insert 压座/斜鸡： wedge耐磨板/油板： wedge wear plate 压条： plate撑头: support pillar 唧嘴： sprue bushing挡板： stop plate 定位圈： locating ring锁扣： latch 扣鸡： parting lock set推杆： push bar 栓打螺丝： S.H.S.B顶板： eracuretun 活动臂： lever arm分流锥： spure sperader 水口司: bush垃圾钉： stop pin 隔片： buffle弹弓柱： spring rod 弹弓: die spring中托司： ejector guide bush 中托边： ejector guide pin镶针： pin 销子： dowel pin波子弹弓： ball catch模具成形不良用语英汉对照aberration 色差 atomization ? 化bank mark ? 料纹 bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜low hole 破孔 blushing 泛白body wrinkle 侧壁皱纹 breaking-in 冒口带肉bubble 膜泡 burn mark 糊斑burr 毛边 camber 翘曲cell 气泡 center buckle 表面中部波皱 check 细裂痕 checking 龟裂chipping 修整表面缺陷 clamp-off 铸件凹痕collapse 塌陷 colormottle 色斑corrosion 腐蚀 crack 裂痕crazing 碎裂 crazing 龟裂deformation 变形 edge 切边碎片edge crack 裂边 fading 退色filler speak 填充料斑 fissure 裂纹flange wrinkle 凸缘起皱 flaw 刮伤flow mark 流痕 galling 毛边glazing 光滑 gloss 光泽grease pits 污斑 grinding defect 磨痕haircrack 发裂 haze 雾度incrustation 水锈 indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点 necking 缩颈nick 割痕 orange peel 橘皮状表面缺陷overflow 溢流 peeling 剥离pit 坑 pitting corrosion 点状腐蚀plate mark 模板印痕 pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂 saponification 皂化scar 疤痕 scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗 torsion 扭曲warpage 翘曲 waviness 波痕webbing 熔塌 weld mark 焊痕whitening 白化 wrinkle 皱纹各式模具分类用语英汉对照landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具counter punch 反凸模 modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模 palletizing die 叠层模family mold 反套制品模具 plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模 positive mold 全压式模具fantail die 扇尾形模具 pressure die 压紧模fishtail die 鱼尾形模具 profile die 轮廓模flash mold 溢料式模具 progressive die 顺序模gypsum mold 石膏铸模 protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具 sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具solid forging die 整体锻模 split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模 stretch form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具 trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模各种模具常用成形方式英汉对照accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形 rubber molding 橡胶成形encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming ? 泡成形 sinter forging 烧结锻造forging roll 轧锻 six sides forging 六面锻造gravity casting 重力铸造 slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻hot forging 热锻 transfer molding 转送成形injection molding 射出成形 warm forging 温锻investment casting 精密铸造 matched die method 对模成形法laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模机械类常用英语：冲压模具-零件类Punch 冲头 insert 入块(嵌入件)deburring punch 压毛边冲子 groove punch 压线冲子stamped punch 字模冲子 round punch 圆冲子special shape punch 异形冲子 bending block 折刀roller 滚轴 baffle plate 挡块located block 定位块 supporting block for location 定位支承块air cushion plate 气垫板 air-cushion eject-rod 气垫顶杆trimming punch 切边冲子 stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子 reel-stretch punch 卷圆压平冲子guide plate 定位板 sliding block 滑块sliding dowel block 滑块固定块 active plate 活动板lower sliding plate 下滑块板 upper holder block 上压块upper mid plate 上中间板 spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆 spring-box eject-plate 弹簧箱顶板bushing block 衬套 cover plate 盖板guide pad 导料块模具工程常用词汇英汉对照——3high-speed transmission 高速传递 heat dissipation 热传rack 上料 degrease 脱脂rinse 水洗 alkaline etch 龄咬desmut 剥黑膜 D.I. rinse 纯水次Chromate 铬酸处理 Anodize 阳性处理Seal 封孔 Revision 版次part number/P/N 料号 good products 良品scraped products 报放心品 defective products 不良品finished products 成品 disposed products 处理品barcode 条码 flow chart 流程表单assembly 组装 stamping 冲压molding 成型 spare parts=buffer 备品coordinate 座标 dismantle the die 折模auxiliary fuction 辅助功能 poly-line 多义线heater band 加热片 thermocouple 热电偶sand blasting 喷沙 grit 砂砾derusting machine 除锈机 degate 打浇口dryer 烘干机 induction 感应induction light 感应光response=reaction=interaction 感应ram 连杆 edge finder 巡边器concave 凸 convex 凹short 射料不足 nick 缺口speck 瑕?? Shine 亮班splay 银纹 gas mark 焦痕delamination 起鳞 cold slug 冷块blush 导色 gouge 沟槽;凿槽satin texture 段面咬花 witness line 证示线patent 专利 grit 沙砾granule=peuet=grain 细粒 grit maker 抽粒机cushion 缓冲 magnalium 镁铝合金magnesium 镁金 metal plate 钣金lathe 车 mill 锉plane 刨 grind 磨drill 铝 boring 镗blinster 气泡 fillet 镶;嵌边through-hole form 通孔形式 voller pin formality 滚针形式cam driver 铡楔 shank 摸柄crank shaft 曲柄轴 augular offset 角度偏差velocity 速度 production tempo 生产进度现状torque 扭矩spline=the multiple keys 花键quenching 淬火tempering 回火annealing 退火 carbonization 碳化alloy 合金 tungsten high speed steel 钨高速的moly high speed steel 钼高速的organic solvent 有机溶剂bracket 小磁导 liaison 联络单volatile 挥发性 resistance 电阻ion 离子 titrator 滴定仪beacon 警示灯 coolant 冷却液crusher 破碎机模具工程常用词汇英汉对照——2stock age analysis sheet 库存货龄分析表 on-hand inventory 现有库存available material 良品可使用 obsolete material 良品已呆滞to be inspected or reworked 待验或重工 total 合计cause description 原因说明 part number/ P/N 料号type 形态 item/group/class 类别quality 品质 prepared by 制表notes 说明 physical inventory 盘点数量year-end physical inventory difference analysis sheet 年终盘点差异分析表physical count quantity 帐面数量 difference quantity 差异量cause analysis 原因分析 raw materials 原料materials 物料 finished product 成品semi-finished product 半成品 packing materials包材disposed goods 处理品 warehouse/hub 仓库on way location 在途仓 oversea location 海外仓spare parts physical inventory list 备品盘点清单spare molds location 模具备品仓 skid/pallet 栈板tox machine 自铆机 wire EDM 线割EDM放电机coil stock 卷料 sheet stock 片料tolerance 工差 score=groove 压线cam block 滑块 pilot 导正筒trim 剪外边 pierce 剪内边drag form 压锻差 pocket for the punch head 挂钩槽slug hole 废料孔 feature die 公母模expansion dwg 展开图 radius 半径shim(wedge) 楔子 torch-flame cut 火焰切割set screw 止付螺丝 form block 折刀stop pin 定位销 round pierce punch=die button 圆冲子shape punch=die insert 异形子 stock locater block 定位块under cut=scrap chopper 清角 active plate 活动板baffle plate 挡块 cover plate 盖板male die 公模 female die 母模groove punch 压线冲子 air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板 bushing block 衬套insert 入块 club car 高尔夫球车capability 能力 parameter r参数factor 系数 phosphate 皮膜化成viscosity 涂料粘度 alkalidipping 脱脂main manifold 主集流脉 bezel 斜视规blanking 穿落模 dejecting 顶固模demagnetization 去磁;消磁模具钢材及零件英语模具钢材alloy tool steel 合金工具钢 aluminium alloy 铝合金钢bearing alloy 轴承合金 blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板 carbon tool steel 碳素工具钢clad sheet 被覆板 clod work die steel 冷锻模用钢emery 金钢砂 ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢 galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢 high speed tool steel 高速度工具钢hot work die steel 热锻模用钢 low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢 marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金 meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁 merchant iron 市售钢材molybdenum high speed steel 钼系高速钢 molybdenum steel 钼钢nickel chromium steel 镍铬钢 prehardened steel 顶硬钢silicon steel sheet 硅钢板 stainless steel 不锈钢tin plated steel sheet 镀锡铁板 tough pitch copper 韧铜troostite 吐粒散铁 tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板塑件&模具相关英文compre sion molding 压缩成型 flash mold 溢流式模具plsitive mold 挤压式模具 split mold 分割式模具cavity 型控母模 core 模心公模taper 锥拔 leather cloak 仿皮革shiver 饰纹 flow mark 流痕welding mark 溶合痕 post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝 striper plate 脱料板piston 活塞 cylinder 汽缸套chip 细碎物handle mold 手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type 蓄料井 insulated runner 绝缘浇道方式hot runner 热浇道 runner plat 浇道模块valve gate 阀门浇口 band heater 环带状的电热器spindle 阀针 spear head 刨尖头slag well 冷料井 cold slag 冷料渣air vent 排气道 h=0.02~0.05mm w=3.2mm L=3~5mmwelding line 熔合痕 eject pin 顶出针knock pin 顶出销 return pin 回位销反顶针sleave 套筒 stripper plate 脱料板insert core 放置入子 runner stripper plate 浇道脱料板guide pin 导销 eject rod (bar) （成型机）顶业捧subzero 深冷处理 three plate 三极式模具runner system 浇道系统 stress crack 应力电裂orientation 定向 sprue gate 射料浇口，直浇口nozzle 射嘴 slag well 冷料井side gate 侧浇口 edge gate 侧缘浇口tab gate 搭接浇口 film gate 薄膜浇口flash gate 闸门浇口 slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口 H=F=1/2t~1/5t T=2.5~3.5mmdiaphragm gate 隔膜浇口 ring gate 环形浇口subarine gate 潜入式浇口 tunnel gate 隧道式浇口pin gate 针点浇口Φ0.8~1.0mm Runner less 无浇道(sprue less) 无射料管方式 long nozzle 延长喷嘴方式Sprue 浇口;溶渣 sprue lock pin 料头钩销(拉料杆)塑件模具相关英文——2eject pin 顶出针 knock pin 顶出销return pin 回位销反顶针 sleave 套筒stripper plate 脱料板 insert core 放置入子runner stripper plate 浇道脱料板 guide pin 导销eject rod (bar) （成型机）顶业捧 subzero 深冷处理three plate 三极式模具 runner system 浇道系统stress crack 应力电裂 orientation 定向sprue gate 射料浇口，直浇口 nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井塑件模具相关英文——1compre sion molding 压缩成型 flash mold 溢流式模具plsitive mold 挤压式模具 split mold 分割式模具cavity 型控母模 core 模心公模taper 锥拔 leather cloak 仿皮革shiver 饰纹 flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝 striper plate 脱料板piston 活塞 cylinder 汽缸套chip 细碎物 handle mold 手持式模具encapsulation molding 低压封装成型、射出成型用模具hot runner 热浇道 runner plat 浇道模块band heater 环带状的电热器 spindle 阀针spear head 刨尖头 cold slag 冷料渣模具相关英语——7Embosss 凸点 dome 凸圆semi-shearing 半剪 stamp mark 冲记号deburr or coin 压毛边 punch riveting 冲压铆合side stretch 侧冲压平 reel stretch 卷圆压平groove 压线 blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印 tick-mark farside 反面压印五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销 coil spring 弹簧lifter pin 顶料销 eq-height sleeves=spool 等高套筒pin 销 lifter guide pin 浮升导料销guide pin 导正销 wire spring 圆线弹簧outer guiding post 外导柱模具工程类plain die 简易模 pierce die 冲孔模forming die 成型模 progressive die 连续模gang dies 复合模 shearing die 剪边模riveting die 铆合模 pierce 冲孔forming 成型(抽凸,冲凸) draw hole 抽孔bending 折弯 trim 切边101个热处理常用英文词汇1. indication 缺陷2. test specimen 试样3. bar 棒材4. stock 原料5. billet 方钢，钢方坯6. bloom 钢坯,钢锭7. section 型材 8. steel ingot 钢锭9. blank 坯料，半成品 10. cast steel 铸钢11. nodular cast iron 球墨铸铁 12. ductile cast iron 球墨铸铁13. bronze 青铜 14. brass 黄铜15. copper 合金 16. stainless steel 不锈钢17. decarburization 脱碳 18. scale 氧化皮19. anneal 退火 20. process anneal 进行退火21. quenching 淬火 22. normalizing 正火23. Charpy impact text 夏比冲击试验 24. fatigue 疲劳25. tensile testing 拉伸试验 26. solution 固溶处理27. aging 时效处理 28. Vickers hardness 维氏硬度29. Rockwell hardness 洛氏硬度30. Brinell hardness 布氏硬度31. hardness tester 硬度计32. descale 除污，除氧化皮等33. ferrite 铁素体34. austenite 奥氏体35. martensite 马氏体 36. cementite 渗碳体37. iron carbide 渗碳体 38. solid solution 固溶体39. sorbite 索氏体 40. bainite 贝氏体41. pearlite 珠光体 44. grain 晶粒42. nodular fine pearlite/ troostite 屈氏体 45. chromium 铬43. black oxide coating 发黑 46. cadmium 镉47. tungsten 钨 48. molybdenum 钼49. manganese 锰 50. vanadium 钒52. silicon 硅 53. sulfer/sulphur 硫54. phosphor/ phosphorus 磷 55. nitrided 氮化的56. case hardening 表面硬化，表面淬硬 57. air cooling 空冷58. furnace cooling 炉冷 59. oil cooling 油冷60. electrocladding /plating 电镀 61. brittleness 脆性62. strength 强度 63. rigidity 刚性,刚度64. creep 蠕变 65. deflection 挠度66. elongation 延伸率 67. yield strength 屈服强度68. elastoplasticity 弹塑性 69. metallographic structure 金相组织70. metallographic test 金相试验 71. carbon content 含碳量72. induction hardening 感应淬火 73. impedance matching 感应淬火74. hardening and tempering 调质 75. crack 裂纹76. shrinkage 缩孔，疏松 77. forging 锻（件）78. casting 铸（件） 79. rolling 轧（件）80. drawing 拉（件） 81. shot blasting 喷丸（处理）82. grit blasting 喷钢砂（处理） 83. sand blasting 喷砂（处理）84. carburizing 渗碳 85. nitriding 渗氮86. ageing/aging 时效 87. grain size 晶粒度88. pore 气孔 89. sonim 夹砂90. cinder inclusion 夹渣91. lattice 晶格93. spectrum analysis 光谱分析 94. heat/thermal treatment 热处理95. inclusion 夹杂物 96. segregation 偏析97. picking 酸洗，酸浸 98. residual stress 残余应力99. remaining stress 残余应力 101. stress relief 应力释放100. relaxation of residual stress 消除残余应力92. abrasion/abrasive/rub/wear/wearing resistance (property) 耐磨性模具相关英语(5)semi-shearing 半剪 stamp mark 冲记号deburr or coin 压毛边 punch riveting 冲压铆合side stretch 侧冲压平 reel stretch 卷圆压平groove 压线 blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印 tick-mark farside 反面压印冲压名称类extension dwg 展开图 procedure dwg 工程图die structure dwg 模具结构图 material 材质material thickness 料片厚度 factor 系数upward 向上 downward 向下press specification 冲床规格 die height range 适用模高die height 闭模高度 burr 毛边gap 间隙 weight 重量total wt. 总重量 punch wt. 上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销 coil spring 弹簧lifter pin 顶料销 eq-height sleeves=spool 等高套筒pin 销 lifter guide pin 浮升导料销guide pin 导正销 wire spring 圆线弹簧outer guiding post 外导柱 stop screw 止付螺丝located pin 定位销 outer bush 外导套模板类top plate 上托板（顶板） top block 上垫脚punch set 上模座 punch pad 上垫板punch holder 上夹板 stripper pad 脱料背板up stripper 上脱料板 male die 公模(凸模)feature die 公母模 female die 母模(凹模)upper plate 上模板 lower plate 下模板die pad 下垫板 die holder 下夹板die set 下模座 bottom block 下垫脚bottom plate 下托板(底板) stripping plate 内外打(脱料板) outer stripper 外脱料板 inner stripper 内脱料板lower stripper 下脱料板注塑模部分中英文对照塑料成形模具 mould for plastics热塑性塑料模 mould for thermoplastics热固性塑料模 mould for thermosets压缩模 compression mould压注模、传递模 transfer mould注射模 injection mould热塑性塑料注射模 injection mould for thermoplastics热固性塑料注射模 injection mould for thermoses序号中文英语日语港台俗称定模座板 fixed clamp plate, top clamping plate. top plate动模座板moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate垫块 spacer parallel支架 ejector housing. mould base leg中文查英文：英语查中文根据国家标准，以下为部分压铸模具术语的标准翻译。
压铸模具专业英语1
landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformedmold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模。
最全的压铸模具相关英语注释
超值压铸英语A 安装尺寸install dimension凹模固定板retainer plate凹模female die, female mold，negative moldB 备件spare parts变质modification变质剂modification agent扒渣slagging—off保温炉holding furnace保压压力dwell pressure表面缺陷surface defectC 淬火硬度quenching hardness抽芯core侧面抽芯side core抽芯油缸core oil cylinder插拔式结构plug抽芯机构core puller抽芯油缸支架bracket of cylinder粗糙度roughness/degree 铸件表面粗糙度surface roughness擦伤galling尺寸公差dimension tolerance of casting除气degassing吹气净化blow purifying除气剂degassing flux出渣de-slagging出渣口slag hole沉渣sludge出炉口tap hole菜花头Cauli—flowering超声波检验ultrasonic test重熔re—meltingD 端盖cover动模垫块spacer parallel锻钢forged steel氮化处理nitriding treatment断裂fracture塑性断裂plastic fracture导柱guide pillar导套guide sleeve导向板guide plate导向件guide part动型moving die/ejector die/movable mould动模座板moving clamp plate/bottom clamping plate 定模座板fixed clamp plate/top plate定型fixed die/cover die定模套版bolster/fixed die顶杆ejector pin顶出结构ejector mechanism顶出ejector吊装孔lifting eye吊环lifting ring镀钛处理titanium plating treatment多肉缺陷metallic projection电火花electric spark打磨grindingF 分流锥divider/blast cone分型面mold parting/parting face/mold joint附页attachment/appendix复位杆reset bar(rod)附件故障accessory覆盖剂covering flux废金属料scrap浮渣cinder反射炉reverberatory furnace废品reject飞边joint flash仿真simulationG 规格specification/standard 数值孔径numerical aperture (N。
压铸模具专业英语
bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模transfer die连续自动冲切,连续冲模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 泡沫成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆)slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣常用塑料英语缩略语英文简称英文全称中文全称ABA Acrylonitrile-butadiene-acrylate 丙烯腈/丁二烯/丙烯酸酯共聚物ABS Acrylonitrile-butadiene-styrene 丙烯腈/丁二烯/苯乙烯共聚物AES Acrylonitrile-ethylene-styrene 丙烯腈/乙烯/苯乙烯共聚物AMMA Acrylonitrile/methyl Methacrylate 丙烯腈/甲基丙烯酸甲酯共聚物ARP Aromatic polyester 聚芳香酯AS Acrylonitrile-styrene resin 丙烯腈-苯乙烯树脂ASA Acrylonitrile-styrene-acrylate 丙烯腈/苯乙烯/丙烯酸酯共聚物CA Cellulose acetate 醋酸纤维塑料CAB Cellulose acetate butyrate 醋酸-丁酸纤维素塑料CAP Cellulose acetate propionate 醋酸-丙酸纤维素CE Cellulose plastics, general 通用纤维素塑料CF Cresol-formaldehyde 甲酚-甲醛树脂CMC Carboxymethyl cellulose 羧甲基纤维素CN Cellulose nitrate 硝酸纤维素CP Cellulose propionate 丙酸纤维素CPE Chlorinated polyethylene 氯化聚乙烯CPVC Chlorinated poly(vinyl chloride) 氯化聚氯乙烯CS Casein 酪蛋白CTA Cellulose triacetate 三醋酸纤维素EC Ethyl cellulose 乙烷纤维素EMA Ethylene/methacrylic acid 乙烯/甲基丙烯酸共聚物EP Epoxy, epoxide 环氧树脂EPD Ethylene-propylene-diene 乙烯-丙烯-二烯三元共聚物EPM Ethylene-propylene polymer 乙烯-丙烯共聚物EPS Expanded polystyrene 发泡聚苯乙烯ETFE Ethylene-tetrafluoroethylene 乙烯-四氟乙烯共聚物EVA Ethylene/vinyl acetate 乙烯-醋酸乙烯共聚物EVAL Ethylene-vinyl alcohol 乙烯-乙烯醇共聚物FEP Perfluoro(ethylene-propylene) 全氟（乙烯-丙烯）塑料FF Furan formaldehyde 呋喃甲醛HDPE High-density polyethylene plastics 高密度聚乙烯塑料HIPS High impact polystyrene 高冲聚苯乙烯IPS Impact-resistant polystyrene 耐冲击聚苯乙烯LCP Liquid crystal polymer 液晶聚合物LDPE Low-density polyethylene plastics 低密度聚乙烯塑料LLDPE Linear low-density polyethylene 线性低密聚乙烯LMDPE Linear medium-density polyethylene 线性中密聚乙烯MBS Methacrylate-butadiene-styrene 甲基丙烯酸-丁二烯-苯乙烯共聚物MC Methyl celluloseMDPE Medium-density polyethylene 中密聚乙烯MF Melamine-formaldehyde resin 密胺-甲醛树脂MPF Melamine/phenol-formaldehyde 密胺/酚醛树脂PA Polyamide (nylon) 聚酰胺（尼龙）PAA Poly(acrylic acid) 聚丙烯酸PADC Poly(allyl diglycol carbonate) 碳酸-二乙二醇酯·烯丙醇酯树脂PAE Polyarylether 聚芳醚PAEK Polyaryletherketone 聚芳醚酮PAI Polyamide-imide 聚酰胺-酰亚胺PAK Polyester alkyd 聚酯树脂PAN Polyacrylonitrile 聚丙烯腈PARA Polyaryl amide 聚芳酰胺PASU Polyarylsulfone 聚芳砜PAT Polyarylate 聚芳酯PAUR Poly(ester urethane) 聚酯型聚氨酯PB Polybutene-1 聚丁烯-[1]PBA Poly(butyl acrylate) 聚丙烯酸丁酯PBAN Polybutadiene-acrylonitrile 聚丁二烯-丙烯腈PBS Polybutadiene-styrene 聚丁二烯-苯乙烯PBT Poly(butylene terephthalate) 聚对苯二酸丁二酯PC Polycarbonate 聚碳酸酯PCTFE Polychlorotrifluoroethylene 聚氯三氟乙烯PDAP Poly(diallyl phthalate) 聚对苯二甲酸二烯丙酯PE Polyethylene 聚乙烯PEBA Polyether block amide 聚醚嵌段酰胺PEBA Thermoplastic elastomer polyether 聚酯热塑弹性体PEEK Polyetheretherketone 聚醚醚酮PEI Poly(etherimide) 聚醚酰亚胺PEK Polyether ketone 聚醚酮PEO Poly(ethylene oxide) 聚环氧乙烷PES Poly(ether sulfone) 聚醚砜PET Poly(ethylene terephthalate) 聚对苯二甲酸乙二酯PETG Poly(ethylene terephthalate) glycol 二醇类改性PETPEUR Poly(ether urethane) 聚醚型聚氨酯PF Phenol-formaldehyde resin 酚醛树脂PFA Perfluoro(alkoxy alkane) 全氟烷氧基树脂PFF Phenol-furfural resin 酚呋喃树脂PI Polyimide 聚酰亚胺PIB Polyisobutylene 聚异丁烯PISU Polyimidesulfone 聚酰亚胺砜PMCA Poly(methyl-alpha-chloroacrylate) 聚α-氯代丙烯酸甲酯PMMA Poly(methyl methacrylate) 聚甲基丙烯酸甲酯PMP Poly(4-methylpentene-1) 聚4-甲基戊烯-1PMS Poly(alpha-methylstyrene) 聚α-甲基苯乙烯POM Polyoxymethylene, polyacetal 聚甲醛PP Polypropylene 聚丙烯PPA Polyphthalamide 聚邻苯二甲酰胺PPE Poly(phenylene ether) 聚苯醚PPO Poly(phenylene oxide) deprecated 聚苯醚PPOX Poly(propylene oxide) 聚环氧（丙）烷PPS Poly(phenylene sulfide) 聚苯硫醚PPSU Poly(phenylene sulfone) 聚苯砜PS Polystyrene 聚苯乙烯PSU Polysulfone 聚砜PTFE Polytetrafluoroethylene 聚四氟乙烯PUR Polyurethane 聚氨酯PVAC Poly(vinyl acetate) 聚醋酸乙烯PVAL Poly(vinyl alcohol) 聚乙烯醇PVB Poly(vinyl butyral) 聚乙烯醇缩丁醛PVC Poly(vinyl chloride) 聚氯乙烯PVCA Poly(vinyl chloride-acetate) 聚氯乙烯醋酸乙烯酯PVDC Poly(vinylidene chloride) 聚（偏二氯乙烯）PVDF Poly(vinylidene fluoride) 聚（偏二氟乙烯）PVF Poly(vinyl fluoride) 聚氟乙烯PVFM Poly(vinyl formal) 聚乙烯醇缩甲醛PVK Polyvinylcarbazole 聚乙烯咔唑PVP Polyvinylpyrrolidone 聚乙烯吡咯烷酮S/MA Styrene-maleic anhydride plastic 苯乙烯-马来酐塑料SAN Styrene-acrylonitrile plastic 苯乙烯-丙烯腈塑料SB Styrene-butadiene plastic 苯乙烯-丁二烯塑料Si Silicone plastics 有机硅塑料SMS Styrene/alpha-methylstyrene plastic 苯乙烯-α-甲基苯乙烯塑料SP Saturated polyester plastic 饱和聚酯塑料SRP Styrene-rubber plastics 聚苯乙烯橡胶改性塑料TEEE Thermoplastic Elastomer,Ether-Ester 醚酯型热塑弹性体TEO Thermoplastic Elastomer, Olefinic 聚烯烃热塑弹性体TES Thermoplastic Elastomer, Styrenic 苯乙烯热塑性弹性体TPEL Thermoplastic elastomer 热塑(性)弹性体TPES Thermoplastic polyester 热塑性聚酯TPUR Thermoplastic polyurethane 热塑性聚氨酯TSUR Thermoset polyurethane 热固聚氨酯UF Urea-formaldehyde resin 脲甲醛树脂UHMWPE Ultra-high molecular weight PE 超高分子量聚乙烯UP Unsaturated polyester 不饱和聚酯VCE Vinyl chloride-ethylene resin 氯乙烯/乙烯树脂VCEV Vinyl chloride-ethylene-vinyl 氯乙烯/乙烯/醋酸乙烯共聚物VCMA Vinyl chloride-methyl acrylate 氯乙烯/丙烯酸甲酯共聚物VCMMA Vinyl chloride-methylmethacrylate 氯乙烯/甲基丙烯酸甲酯共聚物VCOA Vinyl chloride-octyl acrylate resin 氯乙烯/丙烯酸辛酯树脂VCVAC Vinyl chloride-vinyl acetate resin 氯乙烯/醋酸乙烯树脂VCVDC Vinyl chloride-vinylidene chloride 氯乙烯/偏氯乙烯共聚物常用塑料英语缩略语二英文简称英文全称中文全称PA Polyamide (nylon) 聚酰胺（尼龙）PAA Poly(acrylic acid) 聚丙烯酸PADC Poly(allyl diglycol carbonate) 碳酸-二乙二醇酯·烯丙醇酯树脂PAE Polyarylether 聚芳醚PAEK Polyaryletherketone 聚芳醚酮PAI Polyamide-imide 聚酰胺-酰亚胺PAK Polyester alkyd 聚酯树脂PAN Polyacrylonitrile 聚丙烯腈PARA Polyaryl amide 聚芳酰胺PASU Polyarylsulfone 聚芳砜PAT Polyarylate 聚芳酯PAUR Poly(ester urethane) 聚酯型聚氨酯PB Polybutene-1 聚丁烯-[1]PBA Poly(butyl acrylate) 聚丙烯酸丁酯PBAN Polybutadiene-acrylonitrile 聚丁二烯-丙烯腈PBS Polybutadiene-styrene 聚丁二烯-苯乙烯PBT Poly(butylene terephthalate) 聚对苯二酸丁二酯PC Polycarbonate 聚碳酸酯PCTFE Polychlorotrifluoroethylene 聚氯三氟乙烯PDAP Poly(diallyl phthalate) 聚对苯二甲酸二烯丙酯PE Polyethylene 聚乙烯PEBA Polyether block amide 聚醚嵌段酰胺PEBA Thermoplastic elastomer polyether 聚酯热塑弹性体PEEK Polyetheretherketone 聚醚醚酮PEI Poly(etherimide) 聚醚酰亚胺PEK Polyether ketone 聚醚酮PEO Poly(ethylene oxide) 聚环氧乙烷PES Poly(ether sulfone) 聚醚砜PET Poly(ethylene terephthalate) 聚对苯二甲酸乙二酯PETG Poly(ethylene terephthalate) glycol 二醇类改性PETPEUR Poly(ether urethane) 聚醚型聚氨酯PF Phenol-formaldehyde resin 酚醛树脂PFA Perfluoro(alkoxy alkane) 全氟烷氧基树脂PFF Phenol-furfural resin 酚呋喃树脂PI Polyimide 聚酰亚胺PIB Polyisobutylene 聚异丁烯PISU Polyimidesulfone 聚酰亚胺砜PMCA Poly(methyl-alpha-chloroacrylate) 聚α-氯代丙烯酸甲酯PMMA Poly(methyl methacrylate) 聚甲基丙烯酸甲酯PMP Poly(4-methylpentene-1) 聚4-甲基戊烯-1PMS Poly(alpha-methylstyrene) 聚α-甲基苯乙烯POM Polyoxymethylene, polyacetal 聚甲醛PP Polypropylene 聚丙烯PPA Polyphthalamide 聚邻苯二甲酰胺PPE Poly(phenylene ether) 聚苯醚PPO Poly(phenylene oxide) deprecated 聚苯醚PPOX Poly(propylene oxide) 聚环氧（丙）烷PPS Poly(phenylene sulfide) 聚苯硫醚PPSU Poly(phenylene sulfone) 聚苯砜PS Polystyrene 聚苯乙烯PSU Polysulfone 聚砜PTFE Polytetrafluoroethylene 聚四氟乙烯PUR Polyurethane 聚氨酯PVAC Poly(vinyl acetate) 聚醋酸乙烯PVAL Poly(vinyl alcohol) 聚乙烯醇PVB Poly(vinyl butyral) 聚乙烯醇缩丁醛PVC Poly(vinyl chloride) 聚氯乙烯PVCA Poly(vinyl chloride-acetate) 聚氯乙烯醋酸乙烯酯PVDC Poly(vinylidene chloride) 聚（偏二氯乙烯）PVDF Poly(vinylidene fluoride) 聚（偏二氟乙烯）PVF Poly(vinyl fluoride) 聚氟乙烯PVFM Poly(vinyl formal) 聚乙烯醇缩甲醛PVK Polyvinylcarbazole 聚乙烯咔唑PVP Polyvinylpyrrolidone 聚乙烯吡咯烷酮S/MA Styrene-maleic anhydride plastic 苯乙烯-马来酐塑料SAN Styrene-acrylonitrile plastic 苯乙烯-丙烯腈塑料SB Styrene-butadiene plastic 苯乙烯-丁二烯塑料Si Silicone plastics 有机硅塑料SMS Styrene/alpha-methylstyrene plastic 苯乙烯-α-甲基苯乙烯塑料SP Saturated polyester plastic 饱和聚酯塑料SRP Styrene-rubber plastics 聚苯乙烯橡胶改性塑料TEEE Thermoplastic Elastomer,Ether-Ester 醚酯型热塑弹性体TEO Thermoplastic Elastomer, Olefinic 聚烯烃热塑弹性体TES Thermoplastic Elastomer, Styrenic 苯乙烯热塑性弹性体TPEL Thermoplastic elastomer 热塑(性)弹性体TPES Thermoplastic polyester 热塑性聚酯TPUR Thermoplastic polyurethane 热塑性聚氨酯TSUR Thermoset polyurethane 热固聚氨酯UF Urea-formaldehyde resin 脲甲醛树脂UHMWPE Ultra-high molecular weight PE 超高分子量聚乙烯UP Unsaturated polyester 不饱和聚酯VCE Vinyl chloride-ethylene resin 氯乙烯/乙烯树脂VCEV Vinyl chloride-ethylene-vinyl 氯乙烯/乙烯/醋酸乙烯共聚物VCMA Vinyl chloride-methyl acrylate 氯乙烯/丙烯酸甲酯共聚物VCMMA Vinyl chloride-methylmethacrylate 氯乙烯/甲基丙烯酸甲酯共聚物VCOA Vinyl chloride-octyl acrylate resin 氯乙烯/丙烯酸辛酯树脂VCVAC Vinyl chloride-vinyl acetate resin 氯乙烯/醋酸乙烯树脂VCVDC Vinyl chloride-vinylidene chloride 氯乙烯/偏氯乙烯共聚物air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板die 模具die shoe 模瓦figure file, chart file 图档cutting die, blanking die冲模progressive die, follow (-on)die 连续模compound die 复合模punched hole 冲孔panel board 镶块to cutedges=side cut=side scrap 切边to bending 折弯to pull, to stretch 拉伸Line streching, line pulling 线拉伸engraving, to engrave 刻印upsiding down edges 翻边to stake 铆合design modification 设计变化die block 模块folded block 折弯块sliding block 滑块location pin 定位销lifting pin 顶料销die plate, front board 模板padding block 垫块stepping bar 垫条upper die base 上模lower die base 下模座upper supporting blank 上承板upper padding plate blank 上垫板spare dies 模具备品spring 弹簧bolt 螺栓plate 电镀mold 成型material for engineering mold testing 工程试模材料not included in physical inventory 不列入盘点incoming material to be inspected 进货待验PCE assembly production schedule sheet PCE 组装厂生产排配表model 机锺work order 工令revision 版次production control confirmation 生产确认checked by 初审approved by 核准stock age analysis sheet 库存货龄分析表on-hand inventory 现有库存available material 良品可使用obsolete material 良品已呆滞to be inspected or reworked 待验或重工cause description 原因说明part number/ P/N 料号item/group/class 类别prepared by 制year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory 盘点数量physical count quantity 帐面数量difference quantity 差异good product/accepted goods/ accepted parts/good parts 良品defective product/non-good parts 不良品disposed goods 处理品on way location 在途仓oversea location 海外仓spare parts physical inventory list 备品盘点清单spare molds location 模具备品仓skid/pallet 栈板tox machine 自铆机wire EDM 线割EDM 放电机coil stock 卷料sheet stock 片料tolerance 工差score=groove 压线cam block 滑块pilot 导正筒trim 剪外边pierce 剪内边drag form 压锻差pocket for the punch head 挂钩槽slug hole 废料孔feature die 公母模expansion dwg 展开图radius 半径shim(wedge) 楔子torch-flame cut 火焰切割set screw 止付螺丝form block 折刀stop pin 定位销round pierce punch=die button 圆冲子shape punch=die insert 异形子stock locater block 定位块under cut=scrap chopper 清角active plate 活动板baffle plate 挡块cover plate 盖板male die 公模female die 母模groove punch 压线冲子air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板bushing block 衬套insert 入块capability 能力parameter 参数factor 系数phosphate 皮膜化成viscosity 涂料粘度alkalidipping 脱脂main manifold 主集流脉bezel 斜视规blanking 穿落模dejecting 顶固模demagnetization 去磁;消磁high-speed transmission 高速传递heat dissipation 热传rack 上料degrease 脱脂rinse 水洗alkaline etch 龄咬desmut 剥黑膜D.I. rinse 纯水次Chromate 铬酸处理Anodize 阳性处理seal 封孔revision 版次part number/P/N 料号good products 良品scraped products 报放心品defective products 不良品finished products 成品disposed products 处理品barcode 条码flow chart 流程表单assembly 组装stamping 冲压molding 成型spare parts=buffer 备品coordinate 座标dismantle the die 折模auxiliary fuction 辅助功能poly-line 多义线heater band 加热片thermocouple 热电偶sand blasting 喷沙grit 砂砾derusting machine 除锈机degate 打浇口dryer 烘干机induction 感应induction light 感应光response=reaction=interaction 感应ram 连杆edge finder 巡边器concave 凸convex 凹short 射料不足nick 缺口speck 瑕疵shine 亮班splay 银纹gas mark 焦痕delamination 起鳞cold slug 冷块blush 导色gouge 沟槽;凿槽satin texture 段面咬花witness line 证示线patent 专利grit 沙砾granule=peuet=grain 细粒grit maker 抽粒机cushion 缓冲magnalium 镁铝合金magnesium 镁金metal plate 钣金lathe 车mill 锉plane 刨grind 磨drill 铝boring 镗blinster 气泡fillet 镶;嵌边through-hole form 通孔形式voller pin formality 滚针形式cam driver 铡楔shank 摸柄crank shaft 曲柄augular offset 角度偏差velocity 速度production tempo 生产进度现状torque 扭矩spline=the multiple keys 花键quenching 淬火tempering 回火annealing 退火carbonization 碳化alloy 合金tungsten high speed steel 钨高速的moly high speed steel 钼高速的organic solvent 有机溶剂bracket 小磁导liaison 联络单volatile 挥发性resistance 电阻ion 离子titrator 滴定仪beacon 警示灯coolant 冷却液crusher 破碎机plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模pierce 冲孔forming 成型(抽凸,冲凸)draw hole 抽孔bending 折弯trim 切边emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号)shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名塑件模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型、射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 冲孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程序制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机3-plate mold 三板模2-plate mold 二板模leader pin/guide pin 边钉/导边bushing/guide bushing 边司/导套shoulder guide bushing 中托司guide pin 中托边ejector retainner plate 顶针板support plate 托板screw 螺丝dowel pin 管钉ply bar scot 开模槽core/cavity inter-lock 内模管位ejector pin 顶针ejector sleeve 司筒ejector pin 司筒针stripper plate 推板movable core,return core core puller 缩呵nylon latch lock 扣机（尼龙拉勾）lifter 斜顶mold base 模胚（架）cavity insert 上内模core insert 下内模slide 行位（滑块）insert 镶件wedge 压座/斜鸡wedge wear plate 耐磨板/油板plate 压条Lsupport pillar 撑头sprue bushing 唧嘴stop plate 挡板locating ring 定位圈latch 锁扣parting lock set 扣鸡push bar 推杆S.H.S.B 栓打螺丝eracuretun 顶板lever arm 活动臂spure sperader 分流锥bush 水口司stop pin 垃圾钉buffle 隔片spring rod 弹弓柱die spring 弹弓ejector guide bush 中托司ejector guide pin 中托边pin 镶针dowel pin 销子ball catch 波子弹弓pipe plug 喉塞lock plate 锁模块angle from pin 斜顶angle ejector rod 斜顶杆parting locks 尼龙拉勾lever arm 活动臂early return bar 复位键、提前回杆valves 气阀angle pin 斜导边terms 术语parting surface support balance 承压平面平衡parting line venting 模排气return pin and cavity interference 回针碰料位mold base shut hight 模总高超出啤机规格water line interferes withejector pin 顶针碰运水part from cavith (core) side 料位出上/下模cavity direct cut on A-plate,core direct cut on B-plate. 模胚原身出料位Do not use (core/cavity) insert 不准用镶件use beryllium copper insert 用铍铜做镶件preliinary (final) mold design 初步（正式）模图设计reverse core 反呵spring compressed length 弹弓压缩量good stability,stable 稳定性好insufficient rigidity 强度不够even cooling 均匀冷却sticking 扣模thero expansion 热膨胀tolorance 公差copper electrode 铜公(电极）top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location 定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block滑块sliding dowel block 滑块固定块active plate活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块mold [mEuld] n. 模子, 铸型vt. 浇铸, 塑造tooling [5tu:liN] v. 加工模具专业英语入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate 圆形流道：round(full/half runner流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue 热流道板：hot manifold发热管：cartridge heater 探针: thermocouples插头：connector plug 插座：connector socket密封/封料：seal三、运水：water line 喉塞：line lpug 喉管：tube塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing中托司：shoulder guide bushing 中托边L：guide pin顶针板：ejector retainner plate 托板：support plate螺丝：screw 管钉：dowel pin开模槽：ply bar scot 内模管位：core/cavity inter-lock顶针：ejector pin 司筒：ejector sleeve司筒针：ejector pin 推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）：mold base 上内模：cavity insert下内模：core insert 行位（滑块）：slide镶件：insert 压座/斜鸡：wedge耐磨板/油板：wedge wear plate 压条：plate撑头: support pillar 唧嘴：sprue bushing挡板：stop plate 定位圈：locating ring锁扣：latch 扣鸡：parting lock set推杆：push bar 栓打螺丝：S.H.S.B顶板：eracuretun 活动臂：lever arm分流锥：spure sperader 水口司:bush垃圾钉：stop pin 隔片：buffle弹弓柱：spring rod 弹弓:die spring中托司：ejector guide bush 中托边：ejector guide pin镶针：pin 销子：dowel pin。
模具专业英文术语大全
模具英语专业术语模具述语一、入水：gate进入位： gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口： switching runner/gate唧嘴口径： sprue diameter二、流道: runner热流道： hot runner,hot manifold热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴： hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头： connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件： mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板： support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针： ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert 行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut onA-plate,core direct cuton B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length 稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machinecompre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate 型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate 垫块 spacer parallel支架 ejector housing. mould base leg压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate 定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate 直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage针pin 物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity 接触长度contact length接触件电镀层contact plating 接触压力contact pressure接触件中心距contact space 接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ，Ribbon cable柔性印刷电线Flexible printed wiring 多层印制电路Multilayer printedcircuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board，Double-sided board表面安装surface Mounting翘曲warp， bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould 熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time 闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top ClampingPlate Top Plate动模座板 Moving Clamp Plate Bottom ClampingPlate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具标准翻译。
最全的压铸模具相关英语注释
最全的压铸模具相关英语注释超值压铸英语A 安装尺⼨install dimension凹模固定板retainer plate凹模female die, female mold, negative moldB 备件spare parts变质modification变质剂modification agent扒渣slagging-off保温炉holding furnace保压压⼒dwell pressure表⾯缺陷surface defectC 淬⽕硬度quenching hardness抽芯core侧⾯抽芯side core抽芯油缸core oil cylinder插拔式结构plug抽芯机构core puller抽芯油缸⽀架bracket of cylinder粗糙度roughness/degree 铸件表⾯粗糙度surface roughness擦伤galling尺⼨公差dimension tolerance of casting除⽓degassing吹⽓净化blow purifying除⽓剂degassing flux出渣de-slagging出渣⼝slag hole沉渣sludge出炉⼝tap hole菜花头Cauli-flowering超声波检验ultrasonic test重熔re-meltingD 端盖cover动模垫块spacer parallel锻钢forged steel氮化处理nitriding treatment断裂fracture塑性断裂plastic fracture导柱guide pillar导套guide sleeve导向板guide plate导向件guide part动型moving die/ejector die/movable mould动模座板moving clamp plate/bottom clamping plate 定模座板fixed clamp plate/top plate 定型fixed die/cover die定模套版bolster/fixed die顶杆ejector pin顶出结构ejector mechanism顶出ejector吊装孔lifting eye吊环lifting ring镀钛处理titanium plating treatment多⾁缺陷metallic projection电⽕花electric spark打磨grindingF 分流锥divider/blast cone分型⾯mold parting/parting face/mold joint附页attachment/appendix复位杆reset bar(rod)附件故障accessory覆盖剂covering flux废⾦属料scrap浮渣cinder反射炉reverberatory furnace废品reject飞边joint flash仿真simulationG 规格specification/standard 数值孔径numerical aperture (N.A)固定段segment坩埚crucible坩埚炉crucible furnace感应电炉electric induction furnace沟槽blind scab硅SiliconH 滑块sliding block滑块部件moving parts滑块退让return/move back焊补welding-on横浇道runner合模die locking横流道runner回炉料foundry returns合型mold assembling/closing/die locking合型⼒die locking force化学成分不合格chemical consistence analysis J 浇⼝套sprue bush浇排道系统pouring system浇不⾜misrun浇注pouring浇注断裂interrupted pour浇道⽐gating ratio浇包ladle精整dressing and finishing精度accuracy接⼝connector击伤shot damage⾦相组织metallographic structure⾦属残液heel⾦相检验metallographic test⾦属型涂料die coating/coating for metal mold 加压速度rate of pressure increasing间隙clearance精炼refining精炼剂refining flux精密铸造precision casting静置holding/stewing渗透impregnation集渣装置dirt traps夹杂类缺陷inclusion defects夹渣entrapped slag/slag inclusion夹具tool fixturesK 壳体housing开炉blowing in孔洞缺陷cavity库存inventoryL 冷却cooling冷却⽔管cooling water pipe冷却耐压管cooling pressure pipe冷却⽔管⽤密封圈O-ring/sealing ring/gasket ring冷室卧式压铸机horizontal (cold chamber) die casting machine 冷却系统cooling system冷却⽔接⼝cooling water connector冷裂cold crack冷隔cold lap铝Aluminum裂纹crack拉伤caught casting拉杆孔draw bar螺纹screw/thread螺纹结构screw structure螺纹公称直径(直径diameter)公称尺⼨(名义尺⼨) specified size/nominal dimension漏油leakage of oil棱边倒⾓edge炉料charge炉衬furnace lining炉⽓分析flue gas analysis炉前分析on-the-spot sample analysis流痕bloom/flow line⼒学性能不合格physical-mechanical characteristic abnormalM ⽑坯rough/blank⽑坯铸件rough casting⽑刺veining/burr模芯core模框frame模槽mold channel模套chase/bolster/frame模具钢die steel模具图纸mold drawing内浇⼝in-gate冒⼝riser/feeder head冒⼝浇注系统feeder head gating system镁Magnesium锰Manganese密闭耐压系统tightness testN 内浇道in-gate镍NickleP 配油盘pressure plate排⽓块exhaust block排⽓槽air vent排⽓孔vent/venting channel排⽓塞venting plug配合套圆形:fitting sleeve ⽅型: fitting case 跑铝aluminum slop out of mold 喷射冶⾦injecting metallurgy喷丸清理shot blasting cleaning抛丸清理wheel blasting cleaning偏析segregation破坏性实验destructive testQ 取件机extractor去除浇冒⼝de-gating清铲chipping缺陷铸件defecting casting⽓孔blowhole/gas cavity/pinhole/porosity ⽓孔缩blowhole shrinkage去⽑刺de-burring去除氧化⽪de-scaling氢Hydrogen清理cleaningR 热处理heat treatment热电偶测温孔thermocouple well热电偶thermocouple (TC)/pyod热裂hot heating熔炼smelting熔化率melting rate熔炼损耗total melting loss熔池bath熔剂flux熔渣slagS ⽔管water pipe三维造型3 D三坐标测量仪coordinate 3上模座板upper clamping plate缩孔shrinkage缩松dispersed shrinkage疏松porosity(dispersed shrinkage)渗漏leakage缩陷sink/sink in/depression试块test block/test piece/coupon 实时控制系统real-time control system 试模de-buggingT 推板push plate推杆push rod推板导柱push plate guide pillar推板导套push plate guide sleeve凸模固定板punch-retainer plate铜copper钛TitaniumW ⽹状裂纹craze crack/crazing/checking未浇满poured shortX 型芯core型腔mold cavity镶拼处splicing place斜导柱孔hole of inclined guide pillar楔紧块wedge型芯弯曲core bending下模座板lowering clamping plate型芯固定板core-retainer plateX 光射线检验X-ray inspectionY 压铸机die casting machine压室pressure chamber压室⽌⼝(定位)尺⼨dimension/size 压实squeezing compaction 压射shot/injection压射冲头injection piston(ram)/plunger 压铸型die casting die压⼒铸造模具die-casting die易损镶块wear insert易损件wearing parts预应⼒pre-stress永久型permanent mold硬点hard spot溢流槽over flow well印痕indentation氧Oxygen荧光检验fluorescent testZ 真空接⼝vacuum connector真空排⽓管vacuum exhaust block总接头main connector中接头middle connector直浇道sprue转接处(转⼝)transit装配图(铸型装配图) mold assembly drawing铸钢cast steel⽀架ejector housing/mold base leg造渣slag forming真空熔炼vacuum melting真空压铸vacuum die casting/ evacuated die casting增压pressurization针孔pinhole沾铝adhesive aluminum直读光谱分析仪direct-reading spectrograph转运包transfer ladle转向器steering rack柴油式传动叉车Diesel forklift复印机copying machine服务器Server绘图仪Graphic plotter兼容机compatible machine材料库warehouse投影仪projector半⾃动车床semi-automatic lathe半⾃动⽴式钻床drill machine表⾯粗度测量仪surface roughness gauge 布洛维硬度计Brinell hardness gauge 测氢仪Hydrogen gauge叉车充电机charger程控交换机exchanger齿轮油泵oil pump储⽓罐accumulator tank电动葫芦Gantry crane电动试压泵press tester电动斜切机bias cutter电⼦秤weighing scale电⼦扫描仪scanner吊⽃spoon hopper⾼压离⼼风机combustion blower管道泵process water pump烘箱oven监控系统monitoring system简易数控车床digital lathe交流弧焊机Are welder抛光机polisher锯床saw空压机air compressor冷冻式⼲燥机dryer红外线测温仪冷却塔cooling tower⽴式带锯床band saw滤油机oil filter焊接机welder模温机die heater喷粉室回收设备painter system平⾯磨床grinder⽓动量仪air gauge切割机cut-off machine清洗机washer散热器攻丝机tapping machine 台式光谱仪spectrograph台式砂轮机abrasive machine 卧式液压拉床broaching machine 铣床milling machine 钻床drilling machine液压机hydraulic machine真空机vacuum pump时效炉aging furnace电阻炉stress relief furnace探伤机diagnostic machine加⼯中⼼machining center车床lathe钻削中⼼drilling & cutting center别克Buick切边机trim press冷却塔循环泵cooling tower pump循环⽔离⼼泵process water pump脱模剂压送机die lube station取件机extractorFL充痒压铸系统FL oxygen feed die cast system装卸车loader在建⼯程construction in progress捡漏机picker纸芯式滤油器paper element filter电磁阀solenoid valve溢流阀spillover valve调速阀speed control valve压⼒传感器pressure transducer三⾓带wedge shaped belt节流阀throttle governor同步齿型带timing belt喷涂机spray coater轴承(main) bearing浮球阀float valve/ball cock⾏车bridge crane平衡重式叉车counter balanced forklift轮毂螺栓wheel hub bolt制动蹄⽚brake shoe制动液braking fluid叶⽚lamina/vane侧护板side guard plate单列向⼼推⼒球轴承single row radial thrust ball bearing 带防尘盖单列轴承single row bearing shielded 急停按钮scram button三相开关threephase switch⾏程开关limit/travel switch断路器circuit breaker接触器contactor中间继电器intermediate relay时间继电器time relay控制变压器control transformer开关电源switching supply节能灯energy-saving lamp⽇光灯管fluorescent tube⾃整流⾼压汞灯泡self-rectifying high pressure mercury lamp 电⼯胶布garrers/electrical tape焊条welding rod⽯笔slate pencil外圆磨床external grinderHydraulic fluid oil 液压油Safety hook/bolts 安全钩Crosshead ⼗字头Tail stock 尾架尾座Frame cover 护板框盖Toggle top cover 肘环顶Coupling 联轴器Tie-bar 拉杆, 系杆Control panel 控制⾯板Power board 分配板, 配电板Overhauling ⼤修, 拆修Hose 软管, ⽔龙带Warranty period 保修期Nozzle 管⼝, 喷嘴Nature tan ⽇晒后的颜⾊, 茶⾊Electric fitting 电装、Rubber pad 橡胶垫Shock absorbing rubber stopper 减震橡⽪塞Die height 模⼦闭合⾼度Die stroke 动模⾏程Intensification ratio standard 增强⽐标准Plunger stroke 柱塞⾏程Plunger tip penetration 冲头穿透⼒Viscosity index 粘度指数Rated pressure 额定压⼒Plug socket 插⼝, 塞孔Ventilated 通风的Anchor bolt hole 地锚(脚)螺栓孔Inlet ⼊⼝Galvanize 通电流Carbon grain 碳粒Mortar ⽕泥, 砂浆Stretcher 拉伸机Earthing cable 接地电缆Manifold 总管, 集合管Clamp force sensor 夹紧⼒传感器。
模具常用语中英文对照解析
种类中文名称英文名称中文名称英文名称模具种类连续模Progressive die 冲孔模Pierce die 机械手Transfer die 剪边模Trimming die 手动机械手Hand transfer die 下料模Blanking die 单工程模Single die 成形模Forming die 铸造结构模Cast die 折弯模Bending die 简易模Prototype die 围边模Flange die 铆合模Riveting die 拉伸模Draw die 复合模Compound die 快换模Changeable die工序类料带strip 料带图strip layout 工序process 冲导正孔pilot pierce 冲孔pierce 侧冲cam pierce 切边notch 切侧刃notch french 折弯bend 墩薄coin成形form 侧成形cam form 整形restrike 围边flange打凸米boss / dimple 打凸包emboss打字印stamp 打沙拉孔hourglass 面押coin burr 抽孔extrude hole 拍平flat 卷圆curl种类中文名称英文名称中文名称英文名称工序类旋转rotate 铆接rivet产品切边线trim line 铆螺母stake nut 切断cutoff 接刀口mismatch 料带带料处carrier tab 毛刺方向burr direction 压线groove 下料blanking模板类上托板top plate 下托板bottom plate 上垫脚upper parallel 下垫脚lower parallel 上模座upper die set 下模座lower die set 上垫板punch backup 下垫板lower backup 上夹板punch holder 下夹板die holder 上脱料板stripper 下模板die plate 冲头punch 凹模die零件类浮块lifter 浮料板lifter plate 成型公form punch 压料块pressure pad 切边冲头trim punch 刀口trim steel 沉头孔counter bore 冲孔入子button 顶针kick off / ejector 废料切断刀slug breaker 成型凹模forming die 整形公restrike punch 导尺rail 导尺顶杆lifter bolt 导料板rail plate 镶件/入子insert侧冲组件cam 滑块slide滑块上油槽oil groove 铲机driver码模槽mounting slot 储运块storage block 限位柱stop block 起吊孔handing hole 起吊环eyebolt 靠块heel脱料拉杆spool 模座导正块thrust heel种类中文名称英文名称中文名称英文名称零件类耐磨片wear plate 垫片shim压块keeper 初始管位first start pin键槽key slot 键key氮气弹簧nitrogen spring 螺旋弹簧coil spring聚氨酯弹簧urethane导柱guide post 导套guide bushing 插针pilot pin插针套pilot bushing 侧刃french传感器sensor 销dowel螺丝screw 拔牙jackscrew垫圈washer 盲销blind dowel压毛边冲头deburring punch 挡块stopping plate压线冲头groove punch 定位块location block字模冲头stamp punch 圆冲头round punch压筋冲头ribbon punch 气垫板air cushion plate 异形冲头special shape punch 气垫顶杆air-cushion eject-rod 切边冲头trimming punch 上压块pressure block加强筋冲头stiffening rib punch 弹簧箱spring box 定位板guide plate 弹簧箱顶杆spring-box eject-rod 压边圈binder 弹簧箱顶板spring-box eject-plate公差类公差tolerance 公差范围tolerance range 上公差upper tolerance 下公差lower tolerance 公差+/- 0.05 plus minus 0.05 形位公差图GD&T 平面度flatness 直线度Straightness 倾斜度angularity 垂直度perpendicularity 平行度parallelism 圆度roundness种类中文名称英文名称中文名称英文名称公圆柱度cylindricity 面轮廓度surface profile差类线轮廓度line profile 位置度true position 同轴度concentricity 对称度symmetry 圆跳动runout 全跳动total runout 尺寸dimension 角度值angle degree 尺寸全检报告dimensional layout 三次元尺寸报告CMM report冲床相关机械冲床mechanical press 油压机hydraulic press 吨位tonnage 行程stroke / travel 冲床上台面ram 冲床下台面bolster冲床台面布置图press layout 冲床上的快速对正QDC 冲床气垫air cushion 码仔stirrup 闭合高度shut height T型槽T-slot送料机feeder 送料高度feeding height工具卡尺caliper 千分尺micrometer 直尺ruler 高度尺height gage 丝攻screw tap 起子screwdriver 拨牙器jacker 扳手wrench风磨机hand grinder 油石oil stone加工类开料cutting material 钻drill (DR) 攻牙tap 铰ream铣mill 车lathe电脑锣NC mill 线切割wire cutting(W/C) 磨grind 刨planer电火花EDM 镭射laser cutting 倒角chamfer xx的精加工finish XX真空热处理vacuum heattreatment镀钛TD coating 退磁demagnetization 烧焊weld4.1.2 加工说明对照表：加工说明Machining Note注:有0.00的地方为数据填入处外导套OUTER GUIDE BUISHING 起吊杆HANDING PIN实数铣通MILL THRU 正反两面各铣TOP SIDE AND OPP SIDE MILLX:-￠0.00（氮气弹弓过孔，锣穿）单+0.00X:-￠0.00 (DR.THRU FOR GAS SPRING) S+0.00X:-￠0.00（氮气弹弓沉头，正面CNC单+0.00,锣深0.00.)X:-￠0.00 ( CNC C'BORE TOP SIDE FOR GAS SPRING, S+0.00, DP0.00)X:-￠0.00（氮气弹弓沉头，反面CNC单+0.00,锣深0.00.)X:-￠0.00 (CNC C'BORE OPP SIDE FOR GAS SPRING, S+0.00, DP0.00)X:-￠0.00（合销孔,铰)X:-￠0.00 (REAM FOR DOWEL)X:-￠0.00（合销孔,割)单+0.00X:-￠0.00 (W/C FOR DOWEL) S+0.00(正面沉头￠0.00*0.00深,内攻M0.00*1.5牙)(￠0.00*0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)(反面沉头￠0.00*0.00深,内攻M0.00*1.5牙)(￠0.00*0.00 C'BORE DP.0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:-￠0.00（合销孔,钻穿)X:-￠0.00 (DR.THRU FOR DOWEL)X:-￠0.00（一般孔,钻穿)X:-￠0.00 (DR.THRU HL)X:-￠0.00（穿丝孔,钻穿)X:-￠0.00 (DR.THRU FOR WEDM S.H.)X:-￠0.00（漏油孔,钻穿) 按向视图加工X:-￠0.00 (DR.THRU FOR DRAIN HL) ACCORDING VIEW DRAWING TO MACHINING X:-（漏油槽,反面CNC单+0.00,锣深0.00)X:- (CNC POCKET OPP.SIDE FOR DRAIN, S+0.00, DP0.00)X:-￠0.00（基准孔,铰)X:-￠0.00 (REAM FOR DATUM HL)X:-￠0.00钻穿（螺丝过孔)内攻M0.00牙X:-￠0.00 (DR.THRU FOR CLEARANCE HL, TAP M0.00 THR)(正面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 TOP SIDE)(反面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 OPP. SIDE)(侧面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)X:-M0.00钻穿,反面攻深0.00,有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 OPP.SIDE, THR DP0.00)X:-M0.00钻穿,正面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP SIDE, THR DP0.00)X:-M0.00钻穿,正反面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)X:-M0.00盲孔,反面攻深0.00,有效牙0.00X:-M0.00 BLIND HL, TAP WORK DP0.00 OPP. SIDE)X:-M0.00盲孔,正面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP WORK DP0.00 TOP SIDE, THR DP0.00)X:-M0.00盲孔,正反面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)X:-M0.00盲孔,侧面分中攻深0.00,组模自配X:-M0.00 BLIND HL, TAP DP0.00 ON EDGE FROM CENTER , DIE MAKER FIT) (侧面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)X:-M0.00盲孔,侧面分中钻深0.00X:-M0.00 BLIND HL, DR. DP0.00 ON EDGE FROM CENTERX:-M0.00（拨牙螺丝孔，攻穿）X:-M0.00 TAP.THRU FOR JACK SCREWX:-￠0.00（塞打过孔,钻穿)X:-￠0.00 DR.THRU FOR SPOOLX:-￠0.00（弹弓过孔,钻穿)X:-￠0.00 DR.THRU FOR SPRINGX:-￠0.00（弹弓孔,反面沉深0.00)有效深0.00X:-￠0.00 (C'BORE FOR SPRING DP.0.00 OPP.SIDE, USED DP.0.00)X:-￠0.00（弹弓孔,正面沉深0.00)有效深0.00X:-￠0.00 (C'BORE FOR SPRING DP.0.00 TOP.SIDE, WORK DP.0.00)X:-（避空孔,锣穿)单+0.00X:- (POCKET THRU)S+0.00X:-（避空孔,正面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 TOP SIDE)X:-（避空孔,反面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 OPP SIDE)X:-￠0.00（避空孔,反面CNC单+0.00,锣深0.00)X:-￠0.00 (POCKET, CNC MILL S+0.00, DP0.00 OPP.SIDE)X:-￠0.00（避空孔,正面CNC单+0.00,锣深0.00)X:-￠0.00 (POCKET, CNC MILL S+0.00, DP0.00 EDGE SIDE)X:-￠0.00（两用销过孔,割)单+0.00X:-￠0.00 (LIFTER PIN, W/C S+0.00)X:-（导尺避空,CNC单+0.00锣穿)X:- (POCKET FOR RAIL, CNC MILL THRU, S+0.00)X:-（导尺避空,正面CNC单+0.00，锣深0.00)X:- (POCKET FOR RAIL, CNC MILL DP.0.00 TOP SIDE, S+0.00) X:-（导尺避空,反面CNC单+0.00，锣深0.00)X:- (POCKET FOR RAIL, CNC MILL DP.0.00 OPP. SIDE, S+0.00) X:-（浮块避空,正面CNC单+0.00，锣深0.00)X:- (POCKET FOR LIFTER, CNC MILL DP.0.00 TOP SIDE, S+0.00) X:-（浮块孔,割）单+0.00(反面避空单+0.00，锣深0.00)X:-（LIFTER HL, W/C)S+0.00(POCKET DP0.00 S+0.00 OPP.SIDE)X:-（浮块孔,锣）单+0.00(反面避空单+0.00，锣深0.00)X:-（LIFTER HL, MILL)S+0.00(POCKET DP0.00 S+0.00 OPP.SIDE)X:-￠0.00（顶针孔,钻穿)（反面沉头￠0.00*0.00深，内攻M0.00*1.5牙)X:-￠0.00 (EJECT PIN, DR.THRU.)(￠0.00 C'BORE DP0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:-￠0.00（顶针孔,钻穿)（正面沉头￠0.00*0.00深，内攻M0.00*1.5牙)X:-￠0.00 (EJECT PIN, DR.THRU.)(￠0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)X:-￠0.00（导柱（导套）孔,CNC锣)单+0.00X:-￠0.00 CNC MILL FOR GUIDE PIN(BUSHING) S+0.00X:-￠0.00（导柱（导套）孔,割)单+0.00X:-￠0.00 W/C FOR GUIDE PIN(BUSHING) S+0.00X:-M0.00*1.5(止付螺丝，正面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 TOP SIDE)X:-M0.00*1.5(止付螺丝，反面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 OPP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:-（INSERT HL, CNC MILL THRU S+0.00)(阴影部分正面沉头单+0.00，锣深0.00)(SHADE AREA, MILL DP0.00 S+0.00 TOP SIDE)(阴影部分反面沉头单+0.00，锣深0.00)(SHADE AREA, MILL DP0.00 S+0.00 OPP SIDE)X:-（入子孔,割）单+0.00X:-（INSERT HL, W/C S+0.00)(阴影部分扣位正面锣深0.00)(SHADE AREA FOR HEAD POCKET, MILL DP0.00 TOP SIDE)(阴影部分扣位反面锣深0.00)(SHADE AREA FOR HEAD POCKET, MILL DP0.00 OPP. SIDE)(正面沉头单+0.00，锣深0.00)(POCKET, MILL DP0.00 TOP SIDE)注: 此处的沉头不能用C'BORE, 只有圆形的沉头才用C'BORE.(反面沉头单+0.00，锣深0.00)(POCKET, MILL DP0.00 TOP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:- (INSERT HL, CNC MILL THRU. S+0.00)X:-（入子孔,正面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 TOP SIDE)X:-（入子孔,反面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 OPP. SIDE)X:-￠0.00（插针孔,铰)单+0.00X:-￠0.00（REAM S+0.00 FOR PILOT PIN)X:-￠0.00（插针孔,割)单+0.00(正面沉头￠0.00*0.00深)X:-￠0.00（W/C FOR PILOT PIN)(￠0.00 C'BORE DP0.00 TOP SIDE)X:-￠0.00（插针孔,钻穿)(正面沉头￠0.00*0.00深)X:-￠0.00（DR.THRU FOR PILOT PIN)(￠0.00 C'BORE DP0.00 TOP SIDE)X:-（冲头过孔,割)单+0.00(正面避空，CNC单+0.00，锣深0.00)(阴影部分扣位正面锣深0.00)X:-（W/C S+0.00 FOR PUNCH CLEARANCE HL)(POCKET, CNC DP 0.00 S+0.00 TOP SIDE)(POCKET SHADE FOR HEAD, DP0.00 TOP SIDE)X:-（冲头过孔,锣穿)单+0.00(正面避空，CNC单+0.00，锣深0.00)X:-（MILL THRU.FOR PUNCH CLEARANCE HL)(POCKET DP0.00 CNC S+ TOP SIDE)X:-（异形冲孔,直x斜x,割)单+0.00(双线部分，割)单+0.00X:-（W/C FOR SPECIAL HL, 0.00 LAND 0.00 TAPER, S+0.00) (W/C PER DOUBLE LINE S+0.00)X:-（冲孔,直x斜x,割)单+0.00X:-（W/C FOR PIERCE DIE HL, 0.00 LAND 0.00 TAPER S+0.00) X:-（冲孔,割)单+0.00X:-（W/C FOR PIERCE DIE HL S+0.00)X:-￠0.00（冲孔漏屎,钻穿)X:-￠0.00 (DR. THRU FOR CHUTE)X:-（异形冲孔漏屎,CNC单+0.00,锣穿）X:-￠0.00 (MILL. THRU FOR SPECIAL CHUTE S+0.00)X:-（产品落料斜度，实数斜30º锣）X:-（MILL 30 TAPER FOR PART RAMP NO CLEARANCE)X:-（漏屎斜度，直x斜45º锣）X:-（MILL FOR CHUTE 0.00 LAND 45 TAPER)反面沉深底面留0.00MILL UNTIL DP正面沉深底面留MILL UNTIL DP五金模具单词总结模具种类:连续模progressive die机械手transfer die手动机械手hand transfer die单工程模single die/line die复合模compound die铆接模riveting die铸造结构模cast die能快换的模changeover die泡沫模pattern互换性:公差tolerance上公差upper tolerance下公差lower tolerance公差范围tolerance range公差+/- 0.05 plus minus 0.05形位公差图GD&T平面度flatness直线度straightness倾斜度angularity垂直度perpendicularity / squareness平行度parallelism圆度roundness / circularity圆柱度cylindricity面轮廓度surface profile线轮廓度line profile位置度true position同轴度concentricity对称度symmetry圆跳动runout全跳动total runout尺寸dimension角度angle degree全尺寸报告dimensional layout工艺性:料带strip料带图strip layout工序process冲导正孔pilot pierce冲孔pierce侧冲cam pierce切边notch成形后的切边trim切侧刃french trim / fringe trim 厚料切边后的精修边shave折弯bend墩薄coin折弯处压筋gusset成形form侧成形cam form整形restrike / rehit围边flange压线/压长条状筋ribbon打凸米boss / dimple打凸包emboss打字印stamp打沙拉孔hourglass面押coin burr抽孔extrude hole拍平flat / spanking包边hem edge压角cone张角flare切舌lance半剪knockout卷圆curl/热恶劣旋转rotate铆接rivet铆螺母stake nut切断cutoff接刀口mismatch料带带料处carrier tabs毛刺方向burr direction产品切边线trim line模具零件:模具die / tool上托板upper mounting plate 上垫脚upper parallel上模座upper die set上垫板punch backup上夹板punch holder止挡板traveling stop脱料板stripper下模板die plate下垫板die backup plate下模座lower die set下垫脚lower parallel上托板base mounting plate浮块lifter浮料板lifter plate成型公form punch压料块pressure pad切边冲头trim punch刀口trim steel刀口直身位land直5斜1 5mm Land 1 taper 刀口上沉头的深度die life 沉头counter bore冲头倒斜shear高低冲stagger punch球锁冲头ball-lock punch球锁座ball-lock retainer冲孔入子button顶针kick off / ejector废料切断刀slug breaker成型凹模form die整形公restrike form punch 导尺rail /stock guidance导尺顶杆lifter bolt导料板rail plate镶件/入子insert侧冲组件cam滑块slide滑块上油槽oil groove铲机driver码模槽mounting slot储运块storage block限位柱stop block起吊孔handing hole起吊环eyebolt模柄shank靠块heel摆块rocker bender脱料板拉杆stripper bolt模座导正块thrust耐磨片wear sheet耐磨板wear plate垫片shim两用销lifter pin初始管位first start pin内限位standoff压块keeper导柱导套压块keeper/ boss 键槽key slot键key氮气弹簧gas spring / nitrogen spring 氮气弹簧安装法兰mounting flange 氮气弹簧系统nitrogen manifold螺旋弹簧coil spring聚氨酯弹簧urethane弹簧套spring cage导柱guide post导套guide bushing插针pilot pin插针套pilot bushing插针通孔pilot through hole侧刃french误检装置misfeeder传感器sensor误检杆trigger油嘴oil nipple销针dowel pin螺丝screw牙thread拔牙jackscrew内六角螺钉socket head screw垫圈washer螺塞screw plug盲销blind dowel行程,走位stroke / travel吨位tonnage机械冲床mechanical press油压机hydraulic press冲床下台面bolster冲床上台面ram冲床台面布置图press layout冲床码模槽press mounting slot冲床气垫air cushion码模钳stirrup闭合高度shut height送料高度feeding height送料机feederT型槽T-slot避位clearance /pocket掏空pocket挂台head扣位pocket of head通气孔air vent hole漏油孔drain hole漏料孔slug hole基准孔datum hole通孔through hole穿丝孔first wire holeT型槽T-slot拔牙jackscrew摆块rocker bender闭合高度shut height避位clearance /pocket侧冲组件cam侧刃french插针pilot pin插针套pilot bushing插针通孔pilot through hole铲机driver沉头counter bore成型凹模form die成型公form punch冲床码模槽press mounting slot冲床气垫air cushion冲床上台面ram冲床台面布置图press layout冲床下台面bolster冲孔入子button冲头倒斜shear初始管位first start pin储运块storage block穿丝孔first wire hole传感器sensor弹簧套spring cage氮气弹簧gas spring / nitrogen spring 氮气弹簧安装法兰mounting flange氮气弹簧系统nitrogen manifold刀口trim steel刀口上沉头的深度die life刀口直身位land导尺rail /stock guidance导尺顶杆lifter bolt导料板rail plate导套guide bushing导柱guide post导柱导套压块keeper/ boss垫片shim垫圈washer顶针kick off / ejector吨位tonnage废料切断刀slug breaker浮块lifter浮料板lifter plate高低冲stagger punch挂台head滑块slide滑块上油槽oil groove机械冲床mechanical press基准孔datum hole键key键槽key slot聚氨酯弹簧urethane靠块heel扣位pocket of head两用销lifter pin漏料孔slug hole漏油孔drain hole螺塞screw plug螺丝screw螺旋弹簧coil spring码模槽mounting slot码模钳stirrup盲销blind dowel模柄shank模具die / tool模座导正块thrust内六角螺钉socket head screw 内限位standoff耐磨板wear plate耐磨片wear sheet起吊环eyebolt起吊孔handing hole切边冲头trim punch球锁冲头ball-lock punch球锁座ball-lock retainer上垫板punch backup上垫脚upper parallel上夹板punch holder上模座upper die set下托板base mounting plate 上托板upper mounting plate 送料高度feeding height送料机feeder掏空pocket通孔through hole通气孔air vent hole脱料板stripper脱料板拉杆stripper bolt误检杆trigger误检装置misfeeder下垫板die backup plate下垫脚lower parallel下模板die plate下模座lower die set限位柱stop block镶件/入子insert销针dowel pin行程,走位stroke / travel压块keeper压料块pressure pad牙thread油压机hydraulic press油嘴oil nipple整形公restrike form punch 直5斜1 5mm Land 1 taper 止挡板traveling stop机加工:开料cutting material钻drill (DR)攻牙tap铰ream铣mill车lathe电脑锣NC mill线切割wire cutting (W/C)磨grind刨planer电火花EDM镭射laser cutting倒角chamfer精加工finish XX真空热处理vacuum heat treatment镀钛TD coating退磁demagnetization烧焊weldG :40-M6BLIND HL,TAP DP18.00 OPP SIDE,THR DP18.00) 盲孔，反面攻深**G10:4-M30BLIND HL,TAP DP18.00 EDGE SIDE)盲孔，侧攻深**(%%c34.00*14.00 C'BORE DP14.00 TOP SIDE) 正面沉头多少×多少深G2 :24-%%c8.00(REAM FOR DOWEL WORK DP16.00 OPP SIDE,DR%%c6.00 HL)G2 :24-%%c8.00(合销,背铰深16.00,有效深,内钻%%C6.00通孔)G4 :3-%%c10.00(基准孔,背铰深20.00)背面锣25.00*25.00方形沉头，深1.00%%P0.01 (REAM FOR DATUM HL DP20.00,MILL25.00*25.00 OPP SIDE DP1.00%%P0.01)M:2-%%c15.00(弹簧孔,锣深33.00) (C'BORE OR SPRING DP33.00 TOP SIDE,WORK DP33.00)X :3-%%c32.00(导套孔,锣穿,单+0.01)(MILL THRU FOR GUIDE BUSHING S+0.01)G :2-M10盲孔,侧攻深30.00(有效深)(BLIND HL,TAP WORK DP30.00 EDGE SIDE)(沉头5.20%%P0.05深)(SLOT DP5.20%%P0.05 TOP SIDE)L :2-%%c8.000(合销,割)单+0.005 (W/C FOR DOWEL)S+0.005盲孔,攻深20.00(有效深) (BLIND HL,TAP DP20.00 TOP SIDE,THR DP20.00)(插针孔,割,单+0.01) (W/C S+0.01 FOR PILOT PIN)(避位孔,背锣9.80(有效深) (POCKET,MILL DP9.80 OPP SIDE WORK)(冲头过孔,锣穿) (MILL THRU FOR PUNCH CLEARANCE HL)(导柱孔,锣穿,单+0.005) (MILL FOR GUIDE PIN) S+0.005避位槽,背锣深19.00) (POCKET,MILL DP15.40 OPP SIDE)(背,沉头%%c14.00，掏深留11.00) (%%c14.00 C'BORE UNTIL DP14.00 OPP SIDE)下模刀口，实数割，直5斜1.5 （内钻%%C5.0穿丝孔）W/C S+0.00 TRIM STEEL,5.0LAND 1.5TAPER,(DR THRU%%c3.00 WEDM S.H)(MILL FOR INSERT DP30.0%%P0.01 S+0.01)(入子槽,锣深30.00%%p0.01,单+0.01)(氮气槽,背锣深4.00%%P0.1,单+0.1) (GAS SPRING MILL DP4.00 OPP SIDE)S+0.1按向视图加工ACCORDING VIEW DRAWING TO MACHINING试模材料:热扎板HRS (hot-roll steel)冷扎板CRS (cold-roll steel)不锈钢板Stainless steel镀锌板galvanized steel镀铝锌板galvalume steel热扎酸洗板HRPO steel (hot-rolled pickled and oiled steel)工具:卡尺caliper千分尺micrometer拨牙器jacker扳手wrench丝攻screw tap起子screwdriver码模钳stirrup设备/工具:3D Programmable CMM三次元检测仪3D CMM Beam Drilling Machine摇臂钻Bench Drilling Machine钻铣床Caliper卡尺CNC EDM电火花机CNC Machine Center加工中心CNCCNC Milling Machine数控铣床CNCCNC Planer Type Milling Machine龙门刨铣床Hardness Tester硬度计Height Gauge高度仪High Wire Cutting快走丝Hole Puncher 打孔机Horizontal surface grinder小水磨/卧式平面磨床Horizontal surface large grinder大水磨Lathe车床Measurement Surface Plate测量平台Metal Saw Machine锯床Milling Machine铣床Oil Press油压机Pin Gauge标准针规Plastic Injection Machine注塑机Point to Point CMM三次元测量仪Precision surface grinder精密手摇磨Press冲床Projector profile投影机Shear Press剪板机Slow Wire Cutting慢走丝Vertical Milling Machine卧式强力铣床扳手wrench拨牙器jacker卡尺caliper码模钳stirrup起子screwdriver千分尺micrometer丝攻screw tapCARVE 雕刻pothook 挂钩SPECIAL HL 异形孔漏斗 filler角铁 ANGLE IRON展开 expanding微调开关 INCHING SWITCH合叶 HINGE优力胶 RUBBER球锁垫板 LOCK WASHER双线边刀口,不倒角TRIM STEEL NEAR THE DOUBLE LINE NO CHAMFER滑块座:SLIDE SET机械:（engine type) liquid cooled, in-line, 4cylinder, carb (发动机型号)水冷，直列，四缸，化油器式(engine) compression ratio (发动机)压缩比(engine) displacement (发动机)排量(engine) fuel (发动机)燃料13-mode 13工况3rd gear 三档齿轮3-way seat 三向座椅4WD control device 四轮驱动控制装置4WD indicator switch 四轮驱动指示灯开关4WD lamp electrical connection 四轮驱动指示灯接线4WD switch 四轮驱动开关5th synchromesh assy. 五档同步器总成6PK belt 6PK 多楔驱动皮带A / C compressor assembly 空调压缩机总成A / C control assembly 空调控制装置A/C & heater assy. 空调加热器总成A/C blower 空调鼓风机A/C clutch 空调压缩机离合器A/C compressor MTG bracket 空调压缩机安装支架A/C control assy. 空调控制器A/C housing assy. 空调箱总成A/C low pressure switch 空调低压开关A/C mode select switch 空调状态选择开关abdomen performance criterion 腹部性能指标Abdominal Peak Force 腹部力峰值ABS 防抱死制动系统acceleration fuel system 加速系统acceleration running noise level 加速行驶噪声accelerator interlocking type 加速踏板联锁式accounting foundation 财政基础Actual cycle work 实际循环功Actual torso angle 实际躯干角adapter 连接器additional features 附加装置additional rule 附加法规adjust screw 调整螺钉adjuster cable 调整拉线adjuster plug 调整盖adjuster screw assy. 调整螺栓总成adjuster washer 调整棘片adjuster, diff. bearing 差速器轴承调整螺母Adjustment system 调节装置Administration and Registration Division 管理科Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts Which Can Be Fitted and/or Be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of These Prescriptions关于对轮式车辆、安装和/或用于轮式车辆的装备和部件采用统一条件并相互认可基于上述条件批准的协定书Agreement Regulations 协定法规air cleaner 空气滤清器air cleaner assy. 空气滤清器总成air cleaner cartridge 空气滤清器滤芯Air compressor 空压机air condition compressor 空调压缩机air direct 空气走向air filter 空气滤清器air flow 空气流向Air flow meter 空气流量计air jet 空气量孔air metering hole 空气量孔air path 气道Air Pressure of Tire 轮胎气压Air type 空气型air valve 空气阀air-cooled 风冷Aisles 通道Alcohol 酒精all bearing 球轴承alternater bracket 发动机支架alternator 交流发电机alterntor assembly 交流发电机总成alumininum-rim 铝合金钢圈alumininum opposed model 铝制对开式AM/FM cassette stereo radio 调幅/调频立体声收放机ambulance 救护车Amended by 修正文amount of exhaust emission 排气排放量Amplitude resolution 幅度分辨率Analogue magnetic recorder 模拟式磁记录仪ANALYZER 分析仪anchor plate, brake caliper 制动钳安装支架Anchorage 座椅固定装置Angle of divergence 偏离角Angle of rotation 旋转角angles drift off vertical line 指针偏离垂直线的角度Angular diameter of the retro-reflecting device 回复反射装置的角直径annex 附件Announcement 公告anti, shutdown screw 防不灭车调整螺钉Antilock Brake System 防抱死制动系统appendix 附录Applicable motor vehicle 适用机动车Applicable scope 适用范围applicant 申请人application 申请application for notification 认可申请书approval 认可arm, valve rocket 摇臂armature 转子总成armature shaft 电枢轴Arm-rests 靠手Article 条Article 1 第1条Asphalt solution 沥青溶剂Attached document 附署文件attached sheet 附表Attached Table 附表attaching location of seat belt anchorage 座椅安全带固定装置的固定位置attachment 附属文件Attendants onboard 车上值班人员automatic chock cover setting 自动阻风门盖调到automotive electric system 汽车电系automotive engine system 引擎系统automatic transmission 自动变速器，自动排挡变速箱Auxiliary Brake 辅助制动器Auxiliary Direction Indicator Lamps 辅助转向信号灯auxiliary spring 副簧Auxiliary Stop Lamp 辅助驻车灯axle case 桥壳axle case assy. 桥壳总成axle ratio 桥速比axle tube 桥管axle weight 轴重back angle level 靠背角水平仪back angle quadrant 靠背角量角器back pan 靠板back spring 回位弹簧backing plate 制动底板Backing sheet 衬背板Back-Up Light 倒车灯backup washer 支撑挡圈bail wire 卡紧环balance tube 平衡管ball 钢球ball bearing 球轴承ball joint assy. , upper 上球销总成ball valve 球阀ball valve, inlet 进油口球阀bar 拉杆barrier 障碍壁battery 蓄电池battery terminal 蓄电池接线柱bearing cap 轴承盖bearing cover, input shaft 输入轴轴承盖bearing, connecting rod 连杆轴承bearing, input shaft 输入轴轴承Bed for babies 婴儿床bell 带束层bench seat 长条座椅berived cap 轴承盖bezel assy. 框板总成bezel, cluster 表框be pilot 小批量产品blead door 混合风门bleeder screw 放气螺钉blower assy. 鼓风机总成blower motor 鼓风发电机blower resistor 鼓风机电阻blower switch 鼓风机开关body 车身,阀体body & liftgate assembly 车身和举升门总成body assy. 车身总成body block 人体模块body of A/C & heater 空调加热器壳体bolt 主缸连接螺栓bolt, connecting rod 连杆螺栓Booster 助力器boot 护罩BOSCH starter motor assembly “波舍”起动机总成bottle assy. , coolant recover 冷却液回收罐总成bottom houseing, fuel pump 燃油泵下壳体bottom housing, fuel tank 燃油箱下壳体bracket 支架bracket assy. , spring seat 弹簧座支架bracket, steering damper mounting 转向减振器支架brake alarm lamp 制动报警灯brake alarm lamp switch 制动报警灯开关Brake booster 制动助力器brake caliper 制动钳brake caliper assy. 制动钳总成brake caliper piston 制动钳活塞brake combination valve 制动组合阀brake disc 制动盘Brake drum 制动鼓brake fluid 刹车油Brake hose 制动软管brake lining 刹车来令brake line, LF 左前制动油管brake line, RF 右前制动油管brake oil flow 制动液流向brake paddle 制动踏板brake pedal 制动踏板Brake pipe 制动管brake shoes 刹车蹄片brake shoe 制动衬块Brake System 制动系Brake Systems for Tractors and Trailers 牵引车及挂车的制动装置Brake tester 制动器试验台brake valve 制动阀brake warning lamp 制动报警灯brake warning switch 制动报警开关Braking efficiency 制动效能braking force control system 制动控制装置Braking wheel 制动轮branch office 分署breaker 断电器bridge 过桥broadcasting vehicle 广播车brush 碳刷总成Buckle 带扣bulkhead 隔板Bulldozer 推土机bumper 保险杠Bumper element 保险杠构件bus transfer 车辆转移台bushing 衬套bushing, upper control arm 上控制臂衬套Business Place 业务场所bypass valve 旁通阀Cabinet Decision 内阁决议cable guide 拉线导向块cable-operated control system 液压式离合器系统Calibration factor of a data channel 数据通道校正系数calibration gas 标定气体calibration method 标定方法caliper assy. , front brake 前制动钳总成Camber 外倾camber angle 前轮外倾角camshaft 凸轮轴camshaft oil gallery 凸轮轴油道cap 加机油口盖cap assy. , power steering fluid reservoir 动力转向液油罐盖cap assy. , radiator 散热器盖总成cap screws 螺钉cap, connecting rod 连杆盖Capacity 容量,规格Capacity of the fuel tank 燃油箱容量capillary tube 毛细管carbon brushes & brush holder 电刷支架总成Carbon monoxide measuring instrument 一氧化碳分析仪Carburetor 化油器carburetor assy. 化油器总成carburetor bowl 化油器浮子室carburetor bowl vent system 化油器浮子室通风系统carburetor overhaul scheme 化油器分解图carburetor working scheme 化油器工作示意图carcase 胎体case runout (Max.) 差速器壳圆跳动（最大）Caster 后倾Catalyst 催化器category 类别cement and aggregate 水泥和混凝料Centreplane of occupant 乘员中心面Certified 经认证的Cetane number 十六烷值chain 驱动链chain drive 驱动链Channel amplitude class 幅度级通道Channel Frequency Class 频率级通道chassis 底盘chassis dynamometer 底盘测功机chassis shuttle 底盘平移台chassis number 底盘号Check and Maintenance 检查和保养check assy. , front door 前门限位器总成check assy. , rear door 后门限位器总成check ball 回止球check bracket 限位器支架check nut 限位器螺母check valve 单向阀check valve hole 回止阀孔check valve retainer 单向阀保持架check valve spring 单向阀弹簧check weight 回止块Chigi Circular No. 地技第…号Chigi No. 地技第…号Child Restraints 儿童约束装置chime module 蜂鸣器Chishin Circular No. 地审第…号Chishin No. 地审第…号chock heater 阻风门加热器总成chock plate 阻风门chock unloaded 阻风门连动装置choke 阻风门choke device 阻风装置choke unload mode 阻风门卸载状态cigarette lighter 点烟器circuit breaker, wiper/washer 刮水器/洗涤器电器断路器Circular 通告circular notice 通告clamp 卡圈Clamp ring type 锁紧圈式Cleaning efficiency 清洗效率Cleaning period 清洗周期clearance 最小离地间隙Clearance Lamp 示廓灯clinder head 气缸盖clip 卡子cluster housing 组合仪表壳Clutch system 离合器clutch assembly 离合器总成clutch control device 离合器控制装置clutch disc,clutch 离合器片clutch housing 离合器壳clutch master cylinder 离合器主缸clutch working cylinder 离合器工作缸Coating 涂层Code No. 型号Code of Federal Regulations 美国联邦法规总览Coefficient of luminous intensity (CIL) 亮度系数coil spring 圈状弹簧cold air 冷空气cold cranking voltage(min.) 最小冷启动电压collapsible spacer 可压缩隔垫collector 拼装台colorimeter 色度计coloured-light unit 有色灯光组column assy. 转向管柱总成combination brake switch and proporting 组合阀combined lamp 复合灯combined pump 复合泵combined pump diaphragm 复合泵膜片combined pump diaphragm rod 复合泵膜片杆combined pump lifter link 复合泵举升拉杆combined pump move direct 复合泵运动方向Combustion Chamber 燃烧室commutator 换向器compensate opening 补偿孔completion inspection certificate 终了检验证书Completion of notification 完成认可compressor 压缩机compression (both) 气环槽（两个）compression ignition type 压燃式Compression ratio 压缩比concrete mixer truck 混凝土搅拌车condenser 冷凝器condenser assy. 冷凝器总成conduit pipe 导管cone , diff. side bearing 差速器轴承，内圈带滚子cone, pinion front bearing 主动齿轮前轴承内圈带滚子cone, pinion rear bearing 主动齿轮后轴承内圈带滚子Confirmor 确认者connecting rod 连接杆connecting link 连接杆connecting rod journal diameter 连杆轴径connecting rod journal width 连杆轴径宽度connecting rod throttle 连杆喷油孔connector 连接器connector of service valve 维修阀接口Constant speed 等速construction and device 结构和装置control & tube assy. , hyd clutch 离合器工作缸和油管总成Control System 操纵系control valve 控制阀阀门control valve model 控制阀型式control valve seat 控制阀阀座convex plate 凸台cooling fan 冷却风扇cooling system 冷却系统Cornering Lamp 转弯灯corrected 修正的cotter 开口销counter 5th gear 中间轴五档齿轮counter shaft 中间轴coupled condition 连接状态Coupling Device 牵引装置cover 端盖cover & plate assy. 离合器盖及压盘总成cover assy. , air cleaner 空气滤清器盖总成cover, gear 侧盖cover, heater air 空气加热罩cover, rear axle case 后桥壳盖crane vehicle 起重车crankcase 曲轴箱crankshaft 曲轴crankshaft gear 曲轴齿轮crankshaft & connecting 曲轴连杆机构crankshaft oil gallery 曲轴油道crankshaft sprocket 轴承链轮critical flow 临界流Cross sensitivity of a linear transducer 线性传感器的横向灵敏度Crush distance 压碎距离Crush rate 压碎速率Crush Strength 压碎强度Cumulative time 累计时间cup 皮碗cup, diff. side bearing 差速器轴承外圈cup, pinion front bearing 主动齿轮前轴承外圈cup, pinion rear bearing 主动齿轮后轴承外圈Cut-off 明暗截止线cycle 冲程cyclinder head cover 气门室罩Cylinder 气缸cylinder block 汽缸体cylinder body 缸体Cylinder bore 缸径cylinder head 汽缸盖cylinder head cover 气门室罩cylinder number 气缸数cylinder working order(clockwise) 气缸工作顺序（顺时针）damper 转向减振器dangerous article 危险物darkroom 暗室Data channel 数据通道Data Processing 数据处理Date of notification 认可日期Deceleration of the structure 地板减速度Definitions 定义Definitions 术语deflection 偏移defroster 除霜器dehydrator 储液器和干燥器。
模具术语英文翻译-25页文档资料
模具术语英文翻译根据国家标准，以下为部分塑料模具成形术语的标准翻译。
动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具术语的标准翻译。
压力铸造模具 Die-Casting Die压铸模零部件定模 Fixed Die Cover Die定模座板 Fixed Clamping Plate定模套板 Bolster Fixed Die动模 Moving Die Ejector Die动模座板 Moving Clamping Plate直流道 Sprue横流道 Runner内浇口 Gate模具分类Injection Mold 注塑模Plastic Rubber Mould 塑胶模Rubber Molding 橡胶成形Hot Chamber Die Casting 热室压铸Sand Mold Casting 砂模铸造Extrusion Mold 挤出模Multi-Cavity Mold 多模穴模具Stack Mold, Stack Injection Mould 叠层模Plaster Mold 石膏模Three Plates Mold 三板模Plain Die 简易模Pierce Die 冲孔模Forming Die 成型模Progressive Die 连续模Gang Dies 复合模Shearing Die 剪边模Cavity Die 型腔模Riveting Die 铆合模Compression Molding 压缩成型Flash Mold 溢流式模具Extrusion Mold 挤压式模具Split Mold 分割式模具Mould Cavity 型腔母模Mold Core 模芯公模Large Die Mold 大型模具Precise Die Mold 精密模具Complex Die Mold 复杂模具Foaming Mould 发泡模具Metal Die 金属模具Plastic Mold 塑料模具Press Tool Stamping Die Punch Die冲压模具Extrusion Die 挤压模具Graphite Die 石墨模具流道浇口部分Runner System 浇道系统Sprue Cold Material Trap 浇道冷料井Sprue Puller 拉杆Runner Design 流道设计Main Runner 主流道Secondary Runner 次流道Mould Gate Design 浇口设计Submarine Gate 潜伏浇口Tunnel Gate 隧道式浇口Pinpoint Gate 点浇口Fan Gate 扇形浇口Side Gate 侧浇口Edge Gate 侧缘浇口Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口Dish Gate 盘形浇口Diaphragm Gate 隔膜浇口Ring Gate 环形浇口Runnerless 无浇道Sprueless 无射料管方式Long Nozzle 延长喷嘴方式Sprue 浇口，溶渣Insulated Runner Hot Runner 热浇道Runner Plat 浇道模块Valve Gate阀门浇口Slag Well 冷料井Cold Slag 冷料渣Sprue Gate 射料浇口，直浇口Nozzle 射嘴Sprue Lock Pin 料头钩销（拉料杆）注塑缺陷Flash 飞边Warpage 翘曲Air Trap 积风Blush 发赤Flow Line 流痕Splay 银纹Short Shot 短射Sink Mark 缩痕Streak 条纹Void 缩孔Weld Line 熔接线Gas Mark 烧焦Cold Slug 冷斑Delamination 起皮Burr 毛刺Flaw Scratch 刮伤Gloss 光泽Glazing 光滑Surface Check 表面裂痕Hesitation 迟滞注塑工艺Molding Conditions 成型条件Drying 烘干Barrel Temperature 料筒温度Melt Temperature 熔化温度Mold Temperature 模具温度Injection Pressure 注塑压力Back Pressure 背压Injection Speed 注塑速度Screw Speed 螺杆转速Tensile Strength 抗拉强度Tensile Elongation 延伸率Flexural Modulus 弯曲模数Flexural Strength 抗弯强度Shrinkage 收缩率Regrind Usage 次料使用Moulding 模塑机械设备Lathe 车床Planer 刨床Miller Milling Machine 铣床Grinder 磨床Driller 钻床Linear Cutting 线切割Electrical Sparkle 电火花Welder 电焊机Punching Machine 冲床Robot 机械手Common Equipment 常用设备EDM Electron Discharge Machining 放电加工3D Coordinate Measurement 三次元量床Boring Machine 搪孔机Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Cylindrical Grinding Machine 外圆磨床Die Spotting Machine 合模机Engraving Machine 雕刻机Engraving E.D.M 雕模放置加工机Form Grinding Machine 成形磨床, Graphite Machine 石墨加工机Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床模具零件Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具<, /SPAN> Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具常用之工作机械3D Coordinate Measurement 三次元量床Boring Machine 搪孔机CNC Milling Machine CNC铣床Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Copy Lathe 仿形车床Copy Milling Machine 仿形铣床Copy Shaping Machine 仿形刨床Cylindrical Grinding Machine 外圆磨床Die Spotting Machine 合模机Drilling Machine 钻孔机Engraving Machine 雕刻机Engraving E.D.M 雕模放置加工机Form Grinding Machine 成形磨床Graphite Machine 石墨加工机Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床Jig Boring Machine 冶具搪孔机Jig Grinding Machine 冶具磨床Lap Machine 研磨机Machine Center 加工制造中心Multi Model Miller 靠磨铣床NC Drilling Machine NC钻床NC Grinding Machine NC磨床NC Lathe NC车床NC Programming System NC程式制作系统Planer 龙门刨床Profile Grinding Machine 投影磨床Projection Grinder 投影磨床Radial Drilling Machine 旋臂钻床Shaper 牛头刨床Surface Grinder 平面磨床Try Machine 试模机Turret Lathe 转塔车床Universal Tool Grinding Machine 万能工具磨床Vertical Machine Center 立式加工制造中心Wire E.D.M 线割放电加工机入水 Gate进入位 Gate Location水口形式 Gate Type大水口 Edge Gate细水口 Pin-point Gate水口大小 Gate Size转水口 Switching Runner Gate唧嘴口径 Sprue Diameter流道Mold Runner热流道 Hot Runner Hot Manifold温度控制器温控器 Thermostat Thermoregulators Temperature Controller 热嘴冷流道 Hot Sprue Cold Runner唧嘴直流 Direct Sprue Gate圆形流道 Round Full Half Runner流道电脑分析 Mold Flow Analysis流道平衡 Runner Balance热嘴 Hot Sprue热流道板 Hot Manifold发热管 Cartridge Heater探针 Thermocouples插头 Connector Plug插座 Connector Socket密封封料 Seal运水 Water Line喉塞 Line Plug Throat Taps喉管 Tube塑胶管 Plastic Tube快速接头 Jiffy Quick Connector Quick Disconnect Coupling模具零件 Mold Components三板模 3-Plate Mold二板模 2-Plate Mold边钉导边 Leader Pin Guide Pin边司导套 Bushing Guide Bushing中托司 Shoulder Guide Bushing中托边 Guide Pin顶针板 Ejector Retainner Plate托板 Support Plate螺丝 Screw管钉 Dowel Pin开模槽 Ply Bar Scot内模管位 Core Cavity inter-Lock顶针 Ejector Pin司筒 Ejector Sleeve司筒针 Ejector Pin推板 Eject Plate Push Plate Stripper Plate缩呵 Movable Core Return Core Puller扣机（尼龙拉勾） Nylon Latch Lock斜顶 Lifter模胚（架） Mold Base上内模 Cavity Insert下内模 Core Insert行位（滑块） Slide镶件 Insert压座 Wedge耐磨板油板 Wedge Wear Plate压条 Plate撑头 Support Pillar唧嘴 Sprue Bushing挡板 Stop Plate定位圈 Locating Ring锁扣 Latch扣机 Parting Lock Set推杆 Push Bar栓打螺丝 S.H.S.B顶板 Ejector Plate活动臂 Lever Arm分流锥 Sprue Spreader分流板 Spreader Plate水口司 Bush垃圾钉 Stop Pin隔片 Buffle弹弓柱 Spring Rod弹弓 Die Spring中托司 Ejector Guide Bush中托边 Ejector Guide Pin镶针 Pin销子 Dowel Pin波子弹弓 Ball catch喉塞 Pipe Plug锁模块 Lock Plate斜顶 Angle from Pin斜顶杆 Angle Ejector Rod尼龙拉勾 Parting Locks活动臂 Lever Arm复位键提前回杆 Early Return Bar气阀 Valves斜导边 Angle Pin术语 Terms承压平面平衡 Parting Surface Support Balance模排气 Parting Line Venting回针碰料位 Return Pin and Cavity Interference顶针碰运水 Water Line Interferes with Ejector Pin 料位出上下模 Part from Cavith （Core） Side不准用镶件 Do Not Use （Core Cavity） Insert用铍铜做镶件 Use Beryllium Copper Insert初步模图设计 Preliminary Mold Design正式模图设计 Final Mold Design弹弓压缩量 Spring Compressed length稳定性好 Good Stability Stable强度不够 Insufficient Rigidity均匀冷却 Even Cooling扣模 Sticking热膨胀 Thermal Expansion公差 Tolerance铜公（电极） Copper Electrode Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流挡板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom Board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting Lug 铸耳Cavity 模腔模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Joint Pipe Coupler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Inserts 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton Frameworks 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道残料顶销浇道推出杆Sprue Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板Pierce 冲孔Forming 成型（抽凸冲凸）Draw Hole 抽孔Bending 折弯Trim 切边Emboss 凸点Dome 凸圆Semi-Shearing 半剪Stamp Mark 冲记号Deburr or Coin 压毛边Punch Riveting 冲压铆合Side Stretch 侧冲压平Reel Stretch 卷圆压平Groove 压线Blanking 下料Stamp Letter 冲字（料号）Shearing 剪断Tick-Mark Nearside 正面压印Tick-Mark Farside 反面压印Extension Drawing 展开图procedure Drawing 工程图Die Structure Drawing 模具结构图Material 材质Material Thickness 料片厚度Factor 系数Upward 向上Downward 向下Press Specification 冲床规格Die Height Range 适用模高Die Height 闭模高度Burr 毛边Gap 间隙Weight 重量Total Weight 总重量Punch Weight 上模重量Compression Molding 压缩成型Flash Mold 溢流式模具Extrusion Mold 挤压式模具Split Mold 分割式模具Cavity 型腔母模Mold Core 模芯公模Taper 锥拔Leather Cloak 仿皮革Shiver 饰纹Flow Mark 流痕Welding Mark 溶合痕Post Screw Insert 螺纹套筒埋值Self Tapping Screw 自攻螺丝Striper Plate 脱料板Piston 活塞Cylinder 汽缸套Chip 细碎物Handle Mold 手持式模具Encapsulation Molding 低压封装成型Two Plate 两极式（模具）Well Type 蓄料井Insulated Runner 绝缘浇道方式Hot Runner 热浇道Runner Plat 浇道模块Valve Gate 阀门浇口Band Heater 环带状的电热器Spindle 阀针Spear Head 刨尖头Slag Well 冷料井Cold Slag 冷料渣Air Vent 排气道Welding Line 熔合痕Eject Pin 顶出针Knock Pin 顶出销Return Pin 回位销反顶针Sleeve 套筒Stripper Plate 脱料板Insert Core 放置入子Runner Stripper Plate 浇道脱料板Guide Pin 导销Eject Rod （Bar）（成型机）顶业捧Subzero 深冷处理Three Plate 三极式模具Runner System 浇道系统Stress Crack 应力电裂Orientation 定向Sprue Gate 射料浇口，直浇口Nozzle 射嘴Sprue Lock Pin 料头钩销（拉料杆）Slag Well 冷料井Side Gate 侧浇口Edge Gate 侧缘浇口Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口Fan Gate 扇形浇口Dish Gate 因盘形浇口Diaphragm Gate 隔膜浇口Ring Gate 环形浇口Submarine Gate 潜入式浇口Tunnel Gate 隧道式浇口Pin Gate 针点浇口Runnerless 无浇道Sprueless 无射料管方式Long Nozzle 延长喷嘴方式Sprue 浇口溶渣Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合式模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Bending Die 双折冷弯模具偏移弯曲模Extrusion Die 挤出模Palletizing Die 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runnerless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow（Blow） Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Barreling 滚光加工Belling 压凸加工Bending 弯曲加工Blanking 下料加工Bulging 撑压加工Burring 冲缘加工Cam Die Bending 凸轮弯曲加工Caulking 压合加工Coining 压印加工Compressing 压缩加工Compression Bending 押弯曲加工Crowning 凸面加工Curl Bending 卷边弯曲加工Curling 卷曲加工Cutting 切削加工Dinking 切断蕊骨Double Shearing 叠板裁断Drawing 引伸加工Drawing with Ironing 抽引光滑加工Embossing 浮花压制加工Extrusion 挤制加工Filing 锉削加工Fine Blanking 精密下料加工Finish Blanking 光制下料加工Finishing 精整加工Flanging 凸缘加工Folding 折边弯曲加工Folding 折叠加工Forming 成形加工Impact Extrusion 冲击挤压加工Indenting 压痕加工Ironing 引缩加工Knurling 滚花Lock Seaming 固定接合Louvering 百叶窗板加工MarKing 刻印加工Necking 颈缩加工Notching 冲口加工Parting 分断加工Piercing 冲孔加工Progressive Bending 连续弯曲加工Progressive Blanking 连续下料加工Progressive Drawing 连续引伸加工Progressive Forming 连续成形加工Reaming 铰孔加工Restriking 二次精冲加工矫形锻压Riveting 铆接加工Roll Bending 滚筒弯曲加工Roll Finishing 滚压加工Rolling 压延加工Roughing 粗加工Scrapless Machining 无废料加工Seaming 折弯重叠加工Shaving 缺口修整加工Shearing 切断加工Sizing 精压加工矫正加工Slitting 割缝加工Spinning 卷边旋接Staking 铆固Stamping 锻压加工Swaging 挤锻压加工Trimming 整缘加工Upsetting 锻粗加工顶锻镦粗Wiring 抽线加工Aberration 色差Atomization 雾化Bank Mark 料垄迹印Bite 咬入Blacking Hole 涂料孔（铸疵）Blacking Scab 涂料疤Blister 起泡Blooming 起霜Blow Hole 破孔Blushing 泛白Body Wrinkle 侧壁皱纹Breaking-in 冒口带肉Bubble 膜泡Burn Mark 糊斑Flash Burr 毛边Camber Warpage 翘曲Cell 气泡Center Buckle 表面中部波皱Check 细裂痕Checking 龟裂Chipping 修整表面缺陷Clamp-off 铸件凹痕Collapse 塌陷Color Mottle 色斑Corrosion 腐蚀Crackle 裂痕裂纹Crazing 碎裂Crazing 龟裂Distortion Deformation 变形Edge 切边碎片Edge Crack 裂边Fading 退色Filler Speak 填充料斑Fissure 裂纹Flange Wrinkle 凸缘起皱Flaw 刮伤Flow Mark 流痕Galling 毛边Glazing 光滑Gloss 光泽Grease Pits 污斑Grinding Defect 磨痕Haircrack 发裂Haze 雾度Incrustation 水锈Indentation 压痕Internal Porosity 内部气孔Mismatch 偏模Mottle 斑点Necking 缩颈Nick 割痕Orange peel 橘皮状表面缺陷Overflow 溢流Peeling 剥离Pit 坑Pitting Corrosion 点状腐蚀Plate Mark 模板印痕Pock 麻点Pock Mark 痘斑Resin Streak 树脂流纹Resin Wear 树脂脱落Riding 凹陷Sagging 松垂Saponification 皂化Scar 疤痕Scrap 废料Scrap Jam 废料阻塞Scratch 刮伤划痕Scuffing 深冲表面划伤Seam 裂痕Shock Line 模口挤痕Short Shot 充填不足Shrinkage Pool 凹孔Sink Mark 凹痕Skin Inclusion 表皮折叠Straightening 矫直Streak 条状痕Surface Check 表面裂痕Surface Roughening 橘皮状表皮皱折Surging 波动Sweat Out 冒汗Torsion Distortion 扭曲Warpage 翘曲Waviness 波痕Webbing 熔塌Weld Mark 焊痕Whitening 白化Wrinkle 皱纹Gas Aassisted Technology 气辅Bottle Cap Mold 瓶盖模具。
的压铸模具相关英语注释
超值压铸英语.安装尺.instal.dimensio.凹模固定.retaine.plat.凹.femal.die.femal.mold.negativ.mol....spar.part...modificatio..质.modificatio.agen...slagging-of.保温.holdin.furnac.保压压.dwel.pressur.表面缺.surfac.defec..淬火硬度quenchin.hardnes..芯cor.侧面抽芯sid.cor.抽芯油缸cor.oi.cylinde.插拔式结构plu.抽芯机构cor.pulle.抽芯油缸支架bracke.o.cylinde.粗糙度roughness/degre.铸件表面粗糙度surfac.roughnes..伤gallin.尺寸公差dimensio.toleranc.o.castin..气degassin.吹气净化blo.purifyin.除气剂degassin.flu..渣de-slaggin.出渣口sla.hol..渣sludg.出炉口ta.hol.菜花头Cauli-flowerin.超声波检验ultrasoni.tes..熔re-meltin....盖cove.动模垫块space.paralle...forge.stee.氮化处理nitridin.treatmen..裂fractur.塑性断裂plasti.fractur..柱guid.pilla..套guid.sleev.导向板guid.plat.导向件guid.par..型movin.die/ejecto.die/movabl.moul.动模座板movin.clam.plate/botto.clampin.plat.定模座板fixe.clam.plate/to.plat.定型fixe.die/cove.di.定模套版bolster/fixe.di..杆ejecto.pi.顶出结构ejecto.mechanis..出ejecto.吊装孔liftin.ey..环liftin.rin.镀钛处理titaniu.platin.treatmen.多肉缺陷metalli.projectio.电火花electri.spar..磨grinding.分流.divider/blas.con.分型.mol.parting/partin.face/mol.join...attachment/appendi.复位.rese.bar(rod.附件故.accessor.覆盖.coverin.flu.废金属料scra..渣cinde.反射.reverberator.furnac...rejec..边join.flas..真simulatio....specification/standar.数值孔.numerica.apertur.(N.A.固定.segmen..埚crucibl.坩埚炉crucibl.furnac.感应电炉electri.inductio.furnac...blin.sca.硅Silico.....slidin.bloc.滑块部.movin.part.滑块退.return/mov.bac...welding-o.横浇.runne...di.lockin.横流.runne.回炉料foundr.return...mol.assembling/closing/di.lockin.合型.di.lockin.forc.化学成分不合格chemica.consistenc.analysi...浇口.spru.bus.浇排道系统pourin.syste.浇不.misru...pourin.浇注断裂interrupte.pou.浇道.gatin.rati.dl..整dressin.an.finishin...accurac...connecto...sho.damag.金相组.metallographi.structur.金属残液hee.金相检验metallographi.tes.金属型涂.di.coating/coatin.fo.meta.mol.加压速.rat.o.pressur.increasin...clearanc..炼refinin.精炼剂refinin.flu.精密铸.precisio.castin..置holding/stewin...impregnatio.集渣装置dir.trap.夹杂类缺陷inclusio.defect..渣entrappe.slag/sla.inclusio...too.fixtures...housin...blowin.i.孔洞缺陷cavit...inventor....coolin.冷却水.coolin.wate.pip.冷却耐压.coolin.pressur.pip.冷却水管用密封.O-ring/sealin.ring/gaske.rin.冷室卧式压铸.horizonta.(col.chamber.di.castin.machin.冷却系.coolin.syste.冷却水接.coolin.wate.connecto...col.crac...Aluminu...crac...caugh.castin.拉杆.dra.ba...screw/threa.螺纹结.scre.structur.螺纹公称直径(直.diameter.公称尺寸(名义尺寸.specifie.size/nomina.dimensio...leakag.o.oi.棱边倒.edg...charg...furnac.linin.炉气分析flu.ga.analysi.炉前分析on-the-spo.sampl.analysi...bloom/flo.lin.力学性能不合.physical-mechanica.characteristi.abnorma....rough/blan.毛坯铸.roug.castin...veining/bur...cor...fram...mol.channe...chase/bolster/fram.模具.di.stee.模具图.mol.drawin.内浇.in-gat...riser/feede.hea..口浇注系.feede.hea.gatin.syste..Magnesiu..Manganes.密闭耐压系.tightnes.tes..内浇.in-gat..Nickl..配油.pressur.plat.排气.exhaus.bloc.排气.ai.ven.排气.vent/ventin.channe.排气.ventin.plu.配合.圆形:fittin.sleev.方型.fittin.cas...aluminu.slo.ou.o.mol.喷射冶.injectin.metallurg.喷丸清.sho.blastin.cleanin.抛丸清.whee.blastin.cleanin...segregatio.破坏性实.destructiv.test.取件.extracto.去除浇冒.de-gatin...chippin.缺陷铸.defectin.castin...blowhole/ga.cavity/pinhole/porosit.气孔.blowhol.shrinkag.去毛.de-burrin.去除氧化.de-scalin..Hydroge...cleanin..热处.hea.treatmen.热电偶测温.thermocoupl.wel. 热电.thermocoupl.(TC)/pyo...ho.heatin...smeltin.熔化.meltin.rat.熔炼损.tota.meltin.los...bat...flu...sla.....wate.pip.三维造...三坐标测量.coordinat..上模座.uppe.clampin.plat...shrinkag...disperse.shrinkag...porosity(disperse.shrinkage...leakag...sink/sin.in/depressio. ..tes.block/tes.piece/coupo. 实时控制系.real-tim.contro.syste.试.de-buggin....pus.plat...pus.ro.推板导.pus.plat.guid.pilla.推板导.pus.plat.guid.sleev.凸模固定.punch-retaine.plat..coppe..Titaniu..网状裂.craz.crack/crazing/checkin.未浇.poure.shor....cor...mol.cavit.镶拼.splicin.plac.斜导柱.hol.o.incline.guid.pilla.楔紧.wedg.型芯弯.cor.bendin.下模座.lowerin.clampin.plat.型芯固定.core-retaine.plat..光射线检.X-ra.inspectio..压铸.di.castin.machin...pressur.chambe.压室止口(定位)尺.dimension/siz.pactio.压.shot/injectio.压射冲.injectio.piston(ram)/plunge.压铸.di.castin.di.压力铸造模.die-castin.di.易损镶.wea.inser.易损.wearin.part.预应.pre-stres.永久.permanen.mol...har.spo.溢流.ove.flo.wel...indentatio..Oxyge.荧光检.fluorescen.tes..真空接.vacuu.connecto.真空排气.vacuu.exhaus.bloc.总接.mai.connecto.中接.middl.connecto.直浇.spru.转接处(转口)transi.装配图(铸型装配图.mol.assembl.drawin...cas.stee...ejecto.housing/mol.bas.le.造.sla.formin.真空熔.vacuu.meltin.真空压.vacuu.di.casting.evacuate.di.castin.增.pressurizatio...pinhol...adhesiv.aluminu.直读光谱分析.direct-readin.spectrograp.转运dl.转向器steerin.rack柴油式传动叉.Diese.forklif.复印.copyin.machin.服务.Serve.绘图.Graphi.plotte.兼容.compatibl.machin.材料.warehous.投影.projecto.半自动车th.半自动立式钻.dril.machin.表面粗度测量.surfac.roughnes.gaug. 布洛维硬度.Brinel.hardnes.gaug.测氢.Hydroge.gaug.叉车充电.charge.程控交换.exchange.齿轮油.oi.pum.储气.accumulato.tan.电动葫.Gantr.cran.电动试压.pres.teste.电动斜切.bia.cutte.电子.weighin.scal.电子扫描.scanne.吊.spoo.hoppe.高压离心风.combustio.blowe.管道.proces.wate.pum.烘.ove.监控系.monitorin.syste.简易数控车th.交流弧焊.Ar.welde.抛光.polishe.锯.sa.空压presso.冷冻式干燥.drye.红外线测温.冷却.coolin.towe.立式带锯.ban.sa.滤油.oi.filte.焊接.welde.模温.di.heate.喷粉室回收设.painte.syste.平面磨.grinde.气动量.ai.gaug.切割.cut-of.machin.清洗.washe.散热器攻丝.tappin.machin.台式光谱.spectrograp.台式砂轮.abrasiv.machin. 卧式液压拉.broachin.machin.铣.millin.machin.钻.drillin.machin.液压.hydrauli.machin.真空.vacuu.pum.时效.agin.furnac.电阻.stres.relie.furnac.探伤.diagnosti.machin.加工中.machinin.cente.车.lath.钻削中.drillin..cuttin.cente.别.Buic.切边.tri.pres.冷却塔循环.coolin.towe.pum.循环水离心.proces.wate.pum.脱模剂压送.di.lub.statio.取件.extracto.FL充痒压铸系.F.oxyge.fee.di.cas.syste.装卸.loade.在建工.constructio.i.progres.捡漏.picke.纸芯式滤油器pape.elemen.filte.电磁.solenoid valv.溢流阀spillove.valv.调速.spee.contro.valv.压力传感器pressur.transduce.三角带wedg.shape.bel.节流阀erno.同步齿型带timin.belt喷涂机spra.coate.轴承(main.bearin.浮球.floa.valve/bal.coc.行车bridg.cran.平衡重式叉车counte.balance.forklif.轮毂螺栓whee.hu.bol.制动蹄片brak.sho.制动液brakin.flui.叶片lamina/van.侧护板sid.guar.plat.单列向心推力球轴承singl.ro.radia.thrust bal.bearin.带防尘盖单列轴承singl.ro.bearin.shielde.急停按.scra.butto.三相开关threephas.switc.行程开关limit/trave.switc.断路器circui.breake.接触.contacto.中间继电器intermediat.rela.时间继电.tim.rela.控制变压器contro.transforme.开关电源switchin.suppl.节能灯m.日光灯管fluorescen.tub.自整流高压汞灯泡m.电工胶布garrers/electrica.tap.焊条weldin.ro.石笔slat.penci.外圆磨床externa.grinderHydrauli.flui.oi.液压.Safet.hook/bolt.安全.Crosshea.十字.Tai.stoc.尾.尾.Fram.cove.护.框.Toggl.to.cove.肘环.Couplin.联轴.Tie-ba.拉杆.系.Contro.pane.控制面.Powe.boar.分配板.配电.Overhaulin.大修.拆.Hos.软管.水龙.Warrant.perio.保修.Nozzl.管口.喷.Natur.ta.日晒后的颜色.茶.Electri.fittin.电装.Rubbe.pa.橡胶.Shoc.absorbin.rubbe.stoppe.减震橡皮.Di.heigh.模子闭合高.Di.strok.动模行. Intensificatio.rati.standar.增强比标.Plunge.strok.柱塞行.Plunge.ti.penetratio.冲头穿透.Viscosit.inde.粘度指.Rate.pressur.额定压.Plu.socke.插口.塞.Ventilate.通风.Ancho.bol.hol.地锚(脚)螺栓.Inle.入.Galvaniz.通电.Carbo.grai.碳.Morta.火泥.砂.Stretche.拉伸.Earthin.cabl.接地电.Manifol.总管.集合.Clam.forc.senso.夹紧力传感.Attenuat.削.Emulsificatio.乳化作.中子线wir.fo.slidin.出模斜.draf.angl.隔.bu.掉.misru.研.grin.Turbidit.浑浊度Refrac.mete.折光.Sedimen.沉淀.Glyco.乙二.Combustibl.易燃.Water-solubl.水溶性. Greas.pum.黄油泵，油脂.Droolin.滴.Disulfid.二硫化.Lithiu..Gaug.coc.试水位旋. Pressur.matc.valv.压力拟合.Lock/chec.nu.防松螺.Slan.倾.Cor.slidin.fac.型芯滑.Flu.treatmen.熔剂处. Di.clampin.cylinde.模具夹紧气.Cloggin.堵塞，闭.Electrod.ba.电极. Fumigatio.certificat.熏蒸消毒证.Crat.条板箱，柳条.Resi.part.树脂零.Oi.rin.油.Gea.bo.齿轮箱，传动箱,变速.Draf.angl.出模斜.Ta.an.dril.gaug.丝锥和钻头.Ta.bore.螺纹底孔.Ta.cutte.丝锥刀.Ta.di.holde.丝锥板牙两用夹.Ta.handl.丝锥扳.Scre.funne.分液漏. Scre.chasin.machin.螺纹切削.Scre.cuttin.螺纹切.Scre.pitc.gaug.螺距.Scre.rive.螺纹铆.Scre.ven.螺杆通.Rac.housin.齿条.Rac.Tube.油.Cu.Seal.Fee.Pipe.输油.Spool.卷. Recuperatin.Seal(恢复性密封.Inflato.Tube.充气.Cu.Seal.Steerin.Hose.转向胶.Biscui.thicknes.料柄厚度注油.oi.filte.poin.牛皮.kraft/brow.pape.瓦楞.flutin.pape.崩.charg.downslide/collaps. 卡涉现.interferenc.phenomeno.机械加工余.stockin.复制.replace.moul.偏心.offse.distanc.抽大.pul.ti.ba.料.biscui.抽.loos.cor.光整平滑.flatnes.Drai.coc.排气阀，放出开.Wrenc.扳.Stoppe.塞子，制动.Intensifie.增强.Chec.valv.止回.Orific.孔，.Pilo.valv.领示阀，导.Col.shu.冷疤，冷.Flo.mar.波纹，流线.Sho.strok.压射冲. Surg.pressur.冲击压力，脉动压.Jac.bol.定位螺.Ancho.hol.锚栓.Dus.sea.档尘.Valv.cove.气门盖，阀.Cylinde.tub.汽缸.Pisto.ro.活塞.Pisto.rin.活塞.Sho.cylinde.压射.Wir.clam.钢丝.Ai.hos.空气软管，送风.Atomize.喷雾.Straine.滤.Hollo.shaf.空心轴，管. Potentiomete.电位计，分压.Shaf.轴，杆状.Asbesto.wir.石棉.Pulle.滑车，滑.Sprin.washe.弹簧垫.Inverte.电源交换.Cuttin.flui.切削. refractio.coefficien.折光系数Scre.Cuttin.Ta.螺旋切削丝.plu.gaug.塞.colo.shade色.re.lea.powe.红丹.stres.relie.去应.castin.fil.铸型薄.cas.form铸造成形.铸. cas.hous.crane炉前[出铁场]吊.cas.panel铸造面.cas.rotor铸造转. cas.superalloy铸造高温合.cas.tes.block铸造试块[棒.castin.character铸造性.castin.crack缩.castin.fin铸件飞边.铸件披缝.铸件周缘翅.castin.head浇冒.p铸件皱.castin.scar铸疤.浇注.castin.sealer铸件渗补.castin.strain铸造应.castin.stress铸造应.spar.plu.火花.internal-combustio.engin.cylinder内燃机汽.hydraulic.水力.pinion小齿.pinio.bearing小齿轮轴.pinio.cage主动[行星]齿轮架.差速器壳.差速.pinio.cuttin.machine齿轴切削机.pinio.head齿轴齿.pinio.shape.cutter插齿.pinio.spider差速器十字.pinio.stop(起动机的)齿轮停止.valv.housing阀.valv.actuatin.mechanism配气机.valv.ai.relief自动放气.valv.bank阀.valv.barrel阀.valv.bod.attachment阀体连接.valv.bounce阀.valv.bush阀衬.阀[衬].valv.ches.gasket阀柜垫密.valv.cock阀.valv.cottar气阀制.valv.disc阀盘valv.discharg.centrifuge活门卸料式离心.valv.follower阀推.valv.positioner阀门定位.分层Delaminatio.filling-engine梳丝机.fillin.agen.填充剂;填.fillin.auger装载螺.poun填.fillin.funnel注液漏.车.(car.fram.钣.shee.meta.测.sid.plat.内侧板Inne.sid.plat.焊钳solderin.turre.焊.weldin.ro.焊.weldin.spo.焊接机器.weldin.robo.寿命周期成.lif.cycl.cos.前.fore/leadin.axl.后翼子.rea.fende.切削性.cuttin.characteristi.散热性.hea.dispersio.耐磨性.wea.resistan.propert.摩擦系.frictio.coefficien.灰铸.gra.iron.graphiti.cas.iro.过盈配.tight/interferenc.fi. 缸.cylinder.sleeve.barre.tub.pip.导轨.guid.wa.(face.铣刀lin.cutter/facin.cutte.刀.too.pan/cutte.hea.磨削余.grindin.allowanc.耐用.enduranc.钝.passivatio.刀尖圆.circula.pr.knif.poin.(刀具)主偏.enterin.angle.pla.angl.弹性变形.amoun.o.elasti.deformatio.燃烧.combustio.chambe.磨.abrasiv.dus.滤器.straine.cor.差速.differentia.gea.反冲减震.recoilin.shoc.absorbe.废气涡.exhaus.turbin.涡轮增压.turbocharge.增压盲.turboloch喷油.oi.sprayer/atomize.汽化.carbureto.硬质合金刀.carbid.tippe.too.精镗刀.fin.borin.too.动力传动系.powe.transmissio.syste.spanne.扳.(美作:wrench.double-ende.spanne.双头扳. adjustabl.spanner.monke.wrenc.活扳子,活络扳.bo.spanne.管钳.(美作:socke.wrenc.caliper.卡.pincers.tong.夹.wir.cutter.剪线. multipurpos.pliers.universa.plier.万能手.adjustabl.plier.可调手.punc.冲.scrape.三角刮.reame.扩孔.callipe.gaug.孔径.hacksa.钢.greas.gu.注油.oi.ca.油.边刨.sid.plane.插.slottin.machin.车.lath.too.车轮车th.车.turnin.Bayone.卡.Bearin.fitting.轴承配. Bearin.processin.equipmen.轴承加工.Bel.driv.带传.Bendin.machine.弯曲.Borin.head.搪孔.Borin.machine.镗.Cabl.makin.tool.造线.CN.bendin.presse.电脑数控弯折.CN.borin.machine.电脑数控镗.CN.drillin.machine.电脑数控钻.CN.ED.wire-cuttin.machine.电脑数控电火花线切削.CN.electri.discharg.machine.电脑数控电火花.CN.engravin.machine.电脑数控雕刻.CN.grindin.machine.电脑数控磨床the.电脑数控车.CN.machin.too.fitting.电脑数控机床配.lin.machine.电脑数控铣.CN.shearin.machine.电脑数控剪切.C刀.CN.wire-cuttin.machine.电脑数控线切削.Conveyin.chain.输送.Crimpin.tool.卷边工.Disposabl.toolholde.bit.舍弃式刀.Drawin.machine.拔丝.Etchin.machine.蚀刻.Honin.machine.搪磨.Lappin.machine.精研.Millin.head.铣.Mol.polishing/texturin.模具打磨/磨.Planin.machine.刨.aberratio.色.atomizatio.雾.ban.mar.料.bit.咬.blackin.hol.涂料孔(铸疵.blackin.sca.涂料.bliste.起.bloomin.起.blo.hol.破.blushin.泛.bod.wrinkl.侧壁皱.breaking-i.冒口带.bubbl.膜.bur.mar.糊.bur.毛.cambe.翘.cel.气.centr.buckl.表面中部波.chec.细裂.checkin.龟. chippin.修整表面缺.clamp-of.铸件凹.collaps.塌.colou.mottl.色.corrosio.腐.crac.裂.crazin.碎.crazin.龟裂deformatio.变.edg.切边碎.edg.crac.裂.fadin.退.fille.spea.填充料.fissur.裂. flang.wrinkl.凸缘起.fla.刮.flo.mar.流.gallin.毛.glazin.光.glos.光.greas.pit.污.grindin.defec.磨.haircrac.发.haz.雾.incrustatio.水.indentatio.压. interna.porosit.内部气.mismatc.偏.mottl.斑.neckin.缩.nic.割. orang.pee.橘皮状表面缺.overflo.溢.peelin.剥.pi..pittin.corrosio.点状腐.plat.mar.模板印.poc.麻.poc.mar.痘.resi.strea.树脂流.resi.wea.树脂脱.ridin.凹.saggin.松.saponificatio.皂.sca.疤.scra.ja.废料阻.scratc.刮伤/划.scuffin.深冲表面划.sea.裂.shoc.lin.模口挤.shor.sho.充填不.shrinkag.poo.凹孔sin.mar.凹.ski.inclusio.表皮折.straightenin.矫.strea.条状.surfac.chec.表面裂. surfac.roughenin.橘皮状表皮皱.surgin.波.swea.ou.冒.torsio.扭.warpag.翘.wavines.波.webbin.熔.wel.mar.焊.whitenin.白.wrinkl.皱.表面处理关联用.时效硬.ag.hardenin.气体硬.ai.hardenin.空气韧.ai.patternin.退.annealin.阳极效.anod.effec.阳极氧化处.anodizin.滚.barre.platin.滚筒打.barre.tumblin.染黑.blackenin.青熟脆.blu.shortnes.碳酸盐薄膜防锈.bonderizin.箱位退.bo.annealin.封箱渗.bo.carburizin. 辉面电.brigh.electroplatin.光辉热处.brigh.hea.treatmen. 旁路热处.bypas.hea.treatmen.化学电.chemica.platin.化学蒸.chemica.vapo.depositio. 大气热处.controlle.atmospher.锐角效.corne.effec.儒缓放.creepin.discharg.压.embossin.部分淬.selectiv.quenching。
压铸常用英文词汇V5资料
压铸常用英文词汇V5资料---------------------考试---------------------------学资学习网---------------------押题------------------------------广东文灿压铸有限公司Wencan die casting Co., Ltd常用英语术语列表List of die casting terms and vocabulariesV6)( 2011-9-23 re-editproducts and tooling developing 1.新产品以及模具开发2D/3D drawing 平面图/3维图bump among products 货与货之间碰撞capital equipment 资本设备, 固定设备chamfering倒角classification 分类、级别datums 基准datum level 基准水平面datum line 基准线datumplane 【测】基(准)面design/process FMEA D设计/P过程FMEAdie casting 压铸die fabrication 模具加工Die location layout 工模排位图Die polished 省模Die trial 试模electrode for EDM 放电用铜公machining by CNC wire-cut machine 线切割加工machining by electric discharge machine ( EDM ) 电蚀火花加工potential effects of failure 潜在失效后果potential failure mode 潜在失效模式rib and corner 筋肋和尖角subcontractor 外包商set die-casting parameter/locking force/ injection force/injection velocity/shot time/volume of release agent/die-open time/ ejector time/pressure rating/metal temperature/ control temperature/ operation according to WI按工作指示设定压铸参数/锁模力/射料力/射料速度/打锤时间/喷雾量/开模时间/顶出时间/压力参数/料温/控制温度/按照作业指导书作业；thermal expansion 热膨胀2．热处理heat treatmentair cooling 空气冷却annealing 退火carbonization 碳化case hardening 表面硬化，表面淬硬full annealing 完全退火1热处理heat treatment金相组织metallographic structure金相试验metallographic testquenching 淬火residual stress 残余应力tempering 回火3．压铸设备及模具die casting machine and die toolingangle pin 斜导销biscuit /slug 料饼/余料blister 气泡burner 燃烧器casting area最大压铸面积casting insert 铸件镶件casting fin铸件飞边, 铸件披缝, 铸件周缘翅片cavity fill time 充型时间cavity insert 型腔镶块cavity 型腔center furnace 中央熔炉clamp force max. 最大压力coefficient 系数cold chamber machine 冷压室压铸机cold/hot chamber pressure die-casting machine 冷/热室压铸机contraction 收缩core slides/core 活动抽芯（型芯）cover die half(stationary half )/ ejector die half (moveable half ) 前（定）模/后（动）模crucible furnace 坩埚炉crucible pot 坩埚degassing 除气/去气充型流速/浇注速度delivery rate；pouring ratedesign of gating system 浇注系统设计die layout模具排位图模具寿命die life开模行程die stroke拔模斜度draftejector force顶出力ejector pad 顶针痕顶针ejector pinejector stroke 顶出行程feeding 补缩回炉料foundry returnsgating/running system 浇注系统holding furnace 保温炉ingate 内浇道压射冲头injection plungerladle 浇包2锁模力locking force压铸机模板machine platen定模板moving/fixed platen 动/ /最小压模厚度maximum/minimum die height 最大（金属）流动性metal fluidity molten metal 熔化金属nitrogen pressure 氮气压力normalpressure工作压力numerical simulation of casting solidification 铸件凝固数值模拟/开型时间opening time 留型时间渣包溢流槽/ overflow量产模production die样板模prototype dierefining 精炼精炼剂refining agent重熔remelting冒口riser/feeder head横浇道runner浇口流道/runner/gate废金属料scrap再生合金secondary alloy压射室司筒,shot sleeve模板尺寸size of die platen炉渣熔/slag/浮渣sludge/dross 沉凝固solidification直浇道锥（分流器）spreader）sprue pin（spure 直浇道die frame 模架切向横浇道tangential runner导柱/拉杆哥林柱tie bar / 熔损、烧损total melting loss 熔炼损耗率冲模trim die排气口vent冷却水通道water cooling channeldie casting and secondary process4．压铸工艺与后加工工艺alloy component assay report 合金成份化验报告appearance外观中央溶炉center furnace特性characteristics冲水口degatingdie casting 压铸分型线parting line/磨抛光polishing/buffing抛光、磨光polishing3polishing/cotton wheels 抛光用布轮removing burrs round pads of ejector pin 刮项针位批锋磨分型线removing parting line flash砂布轮sanding wheelsmachining process5．精加工工艺rough maching boring 镗精加工fine maching ; 粗加工Horizontal machining center drill bit 钻头卧式加工中心立式加工中心chuck vertical machining center车床卡盘，夹具刀具cutting tools /内螺纹external/internal thread 外file 锉成型刀form tool磨grind夹具jig/fixturelathe 车床left-hand thread左旋螺纹length of thread engagement螺纹旋合长度loose thread滑牙加工精度machining accuracy 铸件机械加工余量machining allowance of casting machining allowance加工余量加工误差machining error机加工芯轴mandrel mill 铣minor diameter小径parallel screw thread 圆柱螺纹中径pitch diameter 螺距pitch,plane 刨铰孔Reaming right-hand thread 右旋螺纹挤牙rolled threads底径root diameter 螺纹screw thread攻牙tappingtight thread牙紧uncompleted tapping 牙不完整surface treatment6．表面处理3分油混合分水a mixture of 2 parts water and 3 parts oil 2 aciddip/pickling 酸洗acid 酸水碱洗alkali cleaning阳极氧化Anodizing烘干baking4/化学氧化blueing /chemical oxide 钢铁发蓝化成处理chemical pretreatment化chromating 铬clear black e-coatings透明黑色泳漆无色铬化clear chroming彩色钝化colored passivationconcentration 浓度dedusting 除尘脱脂，除油degreasing刻蚀descaling浸渍dipping电泳electrophoresis电泳漆electrophoretic coating镀硬铬electroplating hard chromeelectrostatics powder coatings 静电粉沫喷涂电镀E-platinghexavalent chromium 六价铬浸渗impregnationmechanical polishing机械抛光中和neutralization/丝印PAD printing/silk screening 移印passivating 钝化phosphating 磷化resin 树脂rinsing 过清水粗化Roughtening喷粉spray powder下挂taking down三价铬trivalent chromium超声波清洗ultrasonic clean抹天那水wiping with toluenesalt spray testing 盐雾试验quality control7．品质控制外观全检appearance full-inspection回收collectionevaluation / measurement technique 评价/测量技术件首检5first inspection for 5 shotsFreq=frequency 次数来料质量抽查报告incoming quality sampling inspection report工序间质量抽查报告interprocess quality sampling inspection reportpile products up due to laying in disorder 摆放不正确堆积产品processing tour-inspection 制程巡回检查公差过程规范/产品product/process specification /tolerance / projector 投影仪QC 巡检QC tour-inspectionquality final-inspection report 最终检验质量报告5质量首件检查报告quality first piece inspection reportquality traceability analysis report 质量追踪分析表return to supplier 退回供应商抽检sampling inspection自检self-inspection特殊特性分类Special Char. classspot check 抽样检查visual standard 外观标准workmanship standard 工作质量标准defects8.质量缺陷常用语气密性air tightness起泡blister/pimple/bubble碰伤bumps狗牙caniniform/dentate 铸件周缘翅片铸件披缝, casting fin铸件飞边,cold lap 冷隔冷纹cold shutContamination 污染尘点dirt pits变形distortion/deformation重皮double skin顶针位凹凸ejector marks raised or depressedelephant skin皱皮slag inclusion 夹渣entrapped slag；filling to excess 多料flow line 流痕/波纹flow mark缺料incomplete filling形状不合格incorrect casting form凹痕印痕/indentation铸件内在质量internal quality of casting疏松【显微疏松】；porosity micro-shrinkage 尺寸不合格；off dimensionoff size油渍oil marksorange peel 桔皮缺陷out of size 尺寸不符oxidation 氧化partial breakage of a casting 崩料电镀脱皮peeling针孔pinhole pits 面麻砂孔porosityroughness 粗糙sand inclusion 砂眼/scratches 划痕刮伤shrinkage 缩水炉渣slag6stain 污渍致密性texturing热缩裂产品中的)thermal shrinkage crack （on product）() 产品表面凸起的龟裂线raised crack mark line (on product) ( visual quality of casting 铸件外观质量气孔砂眼/void挠曲warpageyellowing发黄铸件合格品率yield of castingmissrun 欠铸testing9. 压铸件试验常用语adhesion 附着性挠度deflection弹塑性elastoplasticityelongation 延伸率延伸extend涂膜厚度film thicknessfilm thickness gauge 膜厚仪屈曲挠性flexibility硬度hardnessheat impact test 热冲击试验high humidity test 高湿测试humidity resistance 耐湿impact resistance 抗冲击力冲击性impact strength 胶带附着力测试measuring adhesion by tape test 中性盐雾neutral salt-spray NSS test残余应力residual stressspraying viscosity 喷涂粘度加强、巩固strengthen拉紧、张力tension粘度viscositywater resistance 耐水性yield strength 屈服强度chemical analysis 化学成份mechanical property 力学性能measurement and gauge10.测量工具常用语高度仪Altitude gauge平均值average块规Block Gauge孔规Bore Gauge间隙规/Clearance gauge 塞尺CMM 三坐标测试仪深度千分尺Depth MicrometerDigital caliper 电子卡尺Digital Height Gauge 数字高度测量仪7硬度计durometer/hardness meter电子称Electric/digital Balance电镀厚度测试仪Electroplating THK.T ester设备变差equipment variation重复性和再现性报告gage repeatability and reproducibility report 量具的R&R 通-止规“过”-- “不过”验规go-no-go gauge Rockwell testing /维氏硬度仪HRC/HV Hardness Tester 洛冲击仪impact tester外径千分尺内/Inside/outer Micrometer测量设备分析measurement unit analysis千分卡尺Micrometer Calipersmetallographic microscope 金相显微镜Microscope 显微镜electric universal testing 电子万能试验机万用表Multimeter normal distribution curve 正态分布曲线零件数量number of parts实验次数number of trials单极差one rangepart variation 零件变差针规pin gauge塞规Plug gage光学影像测量仪Optical image Projector 投影仪公差带range极差控制图range control chart重复性repeatability再现性reproducibility 环规Ring Gauge光谱仪spectrometerThermometer 温度计螺纹规Thread Gaugethread plug gage螺纹塞规Torque Meter 力矩计total variation 总变差力仪Twisting Meter 转扭游标卡尺Vernier Caliper 粘度计viscosimeter目测visual check。
压铸用语中英词汇表
壓鑄用語中英詞彙表Accumulator: 蓄壓器在油壓迴路上用來儲存油壓動力來源之壓力油的容器。
Accumulator Charge: 蓄壓器充填通常指蓄壓器內部所充填的氮氣量。
Area,Vent: 排氣面積排氣槽的截面積或全部模腔的總排氣面積。
Automatic Operation: 自動操作表達一部壓鑄機連續操作不需要操作員去啟動每一次循環的用語。
Bushing: 襯套以軸銷相配的圓柱筒套。
Bushing,Clearance: 襯套間隙襯套內徑與軸銷外徑之配合公差。
Bushing,Guide Pin: 導銷襯套與導銷配合的襯套。
Casting: 鑄件熔解的金屬在模具內凝固成形的產品。
Casting,Cycle: 鑄造循環或過程以壓鑄而言，通常包括凝固時間、機器動作和順序時間。
Casting,Defect: 鑄件缺陷任何一項不能滿足鑄件的設計或品質標準之要點的缺陷。
Casting,Defective: 鑄件不良沒有達到設計或品質規格要求的鑄件。
Casting Rate: 鑄造效率機器持續運行一小時所鑄造的平均射次。
Casting Removal: 鑄件取出將固化成形的鑄件從開啟的模具上拿出的動作。
Casting Section Thickness: 鑄件剖面厚度鑄件的壁厚。
Casting Shrinkage: 鑄件收縮量鑄件在模具中固化成形時與冷卻至室溫時的每一個單位長度尺寸之變化量。
Casting,Temperature: 鑄造溫度在射出時的鑄造溫度。
Casting,Thickness: 鑄件厚度鑄件的剖面厚度。
Casting,Thin Wall: 薄壁鑄件定義一個鑄件滿足功能需求之最小壁厚的用語。
Casting,Volume: 鑄件容積鑄件中金屬的總立方單位（例如：立方英吋或立方公分）。
Cavities,Multiple: 多模穴一副模具上有一個以上的模穴。
Cavity: 模穴壓鑄模具上用來鑄造零件外形尺寸的空間。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
超值压铸英语A 安装尺寸install dimension凹模固定板retainer plate凹模female die, female mold, negative moldB 备件spare parts变质modification变质剂modification agent扒渣slagging-off保温炉holding furnace保压压力dwell pressure表面缺陷surface defectC 淬火硬度quenching hardness抽芯core侧面抽芯side core抽芯油缸core oil cylinder插拔式结构plug抽芯机构core puller抽芯油缸支架bracket of cylinder粗糙度roughness/degree 铸件表面粗糙度surface roughness擦伤galling尺寸公差dimension tolerance of casting除气degassing吹气净化blow purifying除气剂degassing flux出渣de-slagging出渣口slag hole沉渣sludge出炉口tap hole菜花头Cauli-flowering超声波检验ultrasonic test重熔re-meltingD 端盖cover动模垫块spacer parallel锻钢forged steel氮化处理nitriding treatment断裂fracture塑性断裂plastic fracture导柱guide pillar导套guide sleeve导向板guide plate导向件guide part动型moving die/ejector die/movable mould动模座板moving clamp plate/bottom clamping plate 定模座板fixed clamp plate/top plate定型fixed die/cover die定模套版bolster/fixed die顶杆ejector pin顶出结构ejector mechanism顶出ejector吊装孔lifting eye吊环lifting ring镀钛处理titanium plating treatment多肉缺陷metallic projection电火花electric spark打磨grindingF 分流锥divider/blast cone分型面mold parting/parting face/mold joint附页attachment/appendix复位杆reset bar(rod)附件故障accessory覆盖剂covering flux废金属料scrap浮渣cinder反射炉reverberatory furnace废品reject飞边joint flash仿真simulationG 规格specification/standard 数值孔径numerical aperture (N.A)固定段segment坩埚crucible坩埚炉crucible furnace感应电炉electric induction furnace沟槽blind scab硅SiliconH 滑块sliding block滑块部件moving parts滑块退让return/move back焊补welding-on横浇道runner合模die locking横流道runner回炉料foundry returns合型mold assembling/closing/die locking合型力die locking force化学成分不合格chemical consistence analysisJ 浇口套sprue bush浇排道系统pouring system浇不足misrun浇注pouring浇注断裂interrupted pour浇道比gating ratio浇包ladle精整dressing and finishing精度accuracy接口connector击伤shot damage金相组织metallographic structure金属残液heel金相检验metallographic test金属型涂料die coating/coating for metal mold加压速度rate of pressure increasing间隙clearance精炼refining精炼剂refining flux精密铸造precision casting静置holding/stewing渗透impregnation集渣装置dirt traps夹杂类缺陷inclusion defects夹渣entrapped slag/slag inclusion夹具tool fixturesK 壳体housing开炉blowing in孔洞缺陷cavity库存inventoryL 冷却cooling冷却水管cooling water pipe冷却耐压管cooling pressure pipe冷却水管用密封圈O-ring/sealing ring/gasket ring冷室卧式压铸机horizontal (cold chamber) die casting machine冷却系统cooling system冷却水接口cooling water connector冷裂cold crack冷隔cold lap铝Aluminum裂纹crack拉伤caught casting拉杆孔draw bar螺纹screw/thread螺纹结构screw structure螺纹公称直径(直径diameter)公称尺寸(名义尺寸) specified size/nominal dimension漏油leakage of oil棱边倒角edge炉料charge炉衬furnace lining炉气分析flue gas analysis炉前分析on-the-spot sample analysis流痕bloom/flow line力学性能不合格physical-mechanical characteristic abnormalM 毛坯rough/blank毛坯铸件rough casting毛刺veining/burr模芯core模框frame模槽mold channel模套chase/bolster/frame模具钢die steel模具图纸mold drawing内浇口in-gate冒口riser/feeder head冒口浇注系统feeder head gating system镁Magnesium锰Manganese密闭耐压系统tightness testN 内浇道in-gate镍NickleP 配油盘pressure plate排气块exhaust block排气槽air vent排气孔vent/venting channel排气塞venting plug配合套圆形:fitting sleeve 方型: fitting case 跑铝aluminum slop out of mold喷射冶金injecting metallurgy喷丸清理shot blasting cleaning抛丸清理wheel blasting cleaning偏析segregation破坏性实验destructive testQ 取件机extractor去除浇冒口de-gating清铲chipping缺陷铸件defecting casting气孔blowhole/gas cavity/pinhole/porosity 气孔缩blowhole shrinkage去毛刺de-burring去除氧化皮de-scaling氢Hydrogen清理cleaningR 热处理heat treatment热电偶测温孔thermocouple well热电偶thermocouple (TC)/pyod热裂hot heating熔炼smelting熔化率melting rate熔炼损耗total melting loss熔池bath熔剂flux熔渣slagS 水管water pipe三维造型3 D三坐标测量仪coordinate 3上模座板upper clamping plate缩孔shrinkage缩松dispersed shrinkage疏松porosity(dispersed shrinkage)渗漏leakage缩陷sink/sink in/depression试块test block/test piece/coupon 实时控制系统real-time control system试模de-buggingT 推板push plate推杆push rod推板导柱push plate guide pillar推板导套push plate guide sleeve凸模固定板punch-retainer plate铜copper钛TitaniumW 网状裂纹craze crack/crazing/checking未浇满poured shortX 型芯core型腔mold cavity镶拼处splicing place斜导柱孔hole of inclined guide pillar楔紧块wedge型芯弯曲core bending下模座板lowering clamping plate型芯固定板core-retainer plateX 光射线检验X-ray inspectionY 压铸机die casting machine压室pressure chamber压室止口(定位)尺寸dimension/size 压实squeezing compaction压射shot/injection压射冲头injection piston(ram)/plunger 压铸型die casting die压力铸造模具die-casting die易损镶块wear insert易损件wearing parts预应力pre-stress永久型permanent mold硬点hard spot溢流槽over flow well印痕indentation氧Oxygen荧光检验fluorescent testZ 真空接口vacuum connector真空排气管vacuum exhaust block总接头main connector中接头middle connector直浇道sprue转接处(转口)transit装配图(铸型装配图) mold assembly drawing铸钢cast steel支架ejector housing/mold base leg造渣slag forming真空熔炼vacuum melting真空压铸vacuum die casting/ evacuated die casting增压pressurization针孔pinhole沾铝adhesive aluminum直读光谱分析仪direct-reading spectrograph转运包transfer ladle转向器steering rack柴油式传动叉车Diesel forklift复印机copying machine服务器Server绘图仪Graphic plotter兼容机compatible machine材料库warehouse投影仪projector半自动车床semi-automatic lathe半自动立式钻床drill machine表面粗度测量仪surface roughness gauge 布洛维硬度计Brinell hardness gauge测氢仪Hydrogen gauge叉车充电机charger程控交换机exchanger齿轮油泵oil pump储气罐accumulator tank电动葫芦Gantry crane电动试压泵press tester电动斜切机bias cutter电子秤weighing scale电子扫描仪scanner吊斗spoon hopper高压离心风机combustion blower管道泵process water pump烘箱oven监控系统monitoring system简易数控车床digital lathe交流弧焊机Are welder抛光机polisher锯床saw空压机air compressor冷冻式干燥机dryer红外线测温仪冷却塔cooling tower立式带锯床band saw滤油机oil filter焊接机welder模温机die heater喷粉室回收设备painter system平面磨床grinder气动量仪air gauge切割机cut-off machine清洗机washer散热器攻丝机tapping machine 台式光谱仪spectrograph台式砂轮机abrasive machine 卧式液压拉床broaching machine 铣床milling machine钻床drilling machine液压机hydraulic machine真空机vacuum pump时效炉aging furnace电阻炉stress relief furnace探伤机diagnostic machine加工中心machining center车床lathe钻削中心drilling & cutting center别克Buick切边机trim press冷却塔循环泵cooling tower pump循环水离心泵process water pump脱模剂压送机die lube station取件机extractorFL充痒压铸系统FL oxygen feed die cast system装卸车loader在建工程construction in progress捡漏机picker纸芯式滤油器paper element filter电磁阀solenoid valve溢流阀spillover valve调速阀speed control valve压力传感器pressure transducer三角带wedge shaped belt节流阀throttle governor同步齿型带timing belt喷涂机spray coater轴承(main) bearing浮球阀float valve/ball cock行车bridge crane平衡重式叉车counter balanced forklift轮毂螺栓wheel hub bolt制动蹄片brake shoe制动液braking fluid叶片lamina/vane侧护板side guard plate单列向心推力球轴承single row radial thrust ball bearing 带防尘盖单列轴承single row bearing shielded急停按钮scram button三相开关threephase switch行程开关limit/travel switch断路器circuit breaker接触器contactor中间继电器intermediate relay时间继电器time relay控制变压器control transformer开关电源switching supply节能灯energy-saving lamp日光灯管fluorescent tube自整流高压汞灯泡self-rectifying high pressure mercury lamp 电工胶布garrers/electrical tape焊条welding rod石笔slate pencil外圆磨床external grinderHydraulic fluid oil 液压油Safety hook/bolts 安全钩Crosshead 十字头Tail stock 尾架尾座Frame cover 护板框盖Toggle top cover 肘环顶Coupling 联轴器Tie-bar 拉杆, 系杆Control panel 控制面板Power board 分配板, 配电板Overhauling 大修, 拆修Hose 软管, 水龙带Warranty period 保修期Nozzle 管口, 喷嘴Nature tan 日晒后的颜色, 茶色Electric fitting 电装、Rubber pad 橡胶垫Shock absorbing rubber stopper 减震橡皮塞Die height 模子闭合高度Die stroke 动模行程Intensification ratio standard 增强比标准Plunger stroke 柱塞行程Plunger tip penetration 冲头穿透力Viscosity index 粘度指数Rated pressure 额定压力Plug socket 插口, 塞孔Ventilated 通风的Anchor bolt hole 地锚(脚)螺栓孔Inlet 入口Galvanize 通电流Carbon grain 碳粒Mortar 火泥, 砂浆Stretcher 拉伸机Earthing cable 接地电缆Manifold 总管, 集合管Clamp force sensor 夹紧力传感器Attenuate 削弱Emulsification 乳化作用中子线wire for sliding出模斜度draft angle隔皮bur掉肉misrun研配grindTurbidity 浑浊度Refract meter 折光仪Sediment 沉淀物Glycol 乙二醇Combustible 易燃的Water-soluble 水溶性的Grease pump 黄油泵，油脂泵Drooling 滴料Disulfide 二硫化物Lithium 锂Gauge cock 试水位旋塞Pressure match valve 压力拟合阀Lock/check nut 防松螺母Slant 倾斜Core sliding face 型芯滑面Flux treatment 熔剂处理Die clamping cylinder 模具夹紧气缸Clogging 堵塞，闭合Electrode bar 电极棒Fumigation certificate 熏蒸消毒证书Crate 条板箱，柳条箱Resin parts 树脂零件Oil ring 油环Gear box 齿轮箱，传动箱,变速箱Draft angle 出模斜度Tap and drill gauge 丝锥及钻头规Tap borer 螺纹底孔钻Tap cutter 丝锥刀具Tap die holder 丝锥板牙两用夹头Tap handle 丝锥扳手Screw funnel 分液漏斗Screw chasing machine 螺纹切削机Screw cutting 螺纹切削Screw pitch gauge 螺距规Screw rivet 螺纹铆钉Screw vent 螺杆通孔Rack housing 齿条罩Rack Tubes 油缸Cup Seals Feed Pipes 输油管Spools 卷轴Recuperating Seal(恢复性密封)Inflator Tubes 充气.Cut Seals Steering Hoses 转向胶管Biscuit thickness 料柄厚度注油孔oil filter point牛皮纸kraft/brown paper瓦楞纸fluting paper崩料charge downslide/collapse 卡涉现象interference phenomenon 机械加工余量stocking复制模replaced mould偏心距offset distance抽大缸pull tie bar料头biscuit抽芯loose core光整平滑度flatnessDrain cock 排气阀，放出开关Wrench 扳手Stopper 塞子，制动器Intensifier 增强器Check valve 止回阀Orifice 孔，口Pilot valve 领示阀，导阀Cold shut 冷疤，冷结Flow mark 波纹，流线谱Shot stroke 压射冲程Surge pressure 冲击压力，脉动压力Jack bolt 定位螺栓Anchor hole 锚栓孔Dust seal 档尘圈Valve cover 气门盖，阀盖Cylinder tube 汽缸筒Piston rod 活塞杆Piston ring 活塞环Shot cylinder 压射缸Wire clamp 钢丝钳Air hose 空气软管，送风管Atomizer 喷雾器Strainer 滤网Hollow shaft 空心轴，管轴Potentiometer 电位计，分压计Shaft 轴，杆状物Asbestos wire 石棉线Pulley 滑车，滑轮Spring washer 弹簧垫圈Inverter 电源交换器Cutting fluid 切削液refraction coefficient 折光系数Screw Cutting Tap 螺旋切削丝锥plug gauge 塞规color shade色泽red lead power 红丹粉stress relief 去应力casting film 铸型薄膜cast form铸造成形, 铸型cast house crane炉前[出铁场]吊车cast panel铸造面板cast rotor铸造转子cast superalloy铸造高温合金cast test block铸造试块[棒]casting character铸造性能casting crack缩裂casting fin铸件飞边, 铸件披缝, 铸件周缘翅片casting head浇冒口casting lap铸件皱纹casting scar铸疤, 浇注疤casting sealer铸件渗补剂casting strain铸造应变casting stress铸造应力spark plug 火花塞internal-combustion engine cylinder内燃机汽缸hydraulics 水力学pinion小齿轮pinion bearing小齿轮轴承pinion cage主动[行星]齿轮架, 差速器壳, 差速盘pinion cutting machine齿轴切削机床pinion head齿轴齿顶pinion shaped cutter插齿刀pinion spider差速器十字轴pinion stop(起动机的)齿轮停止器valve housing阀套valve actuating mechanism配气机构valve air relief自动放气阀valve bank阀组valve barrel阀缸valve body attachment阀体连接头valve bounce阀跳valve bush阀衬, 阀[衬]套valve chest gasket阀柜垫密片valve cock阀栓valve cottar气阀制销valve disc阀盘valve discharge centrifuge活门卸料式离心机valve follower阀推杆valve positioner阀门定位器分层Delaminationfilling-engine梳丝机器filling agent 填充剂;填料filling auger装载螺旋filling compoun填料filling funnel注液漏斗车架(car) frame钣金sheet metal测板side plate内侧板Inner side plate焊钳soldering turret焊条welding rod焊点welding spot焊接机器人welding robot寿命周期成本life cycle cost前轴fore/leading axle后翼子板rear fender切削性能cutting characteristic散热性能heat dispersion 耐磨性能wear resistant property 摩擦系数friction coefficient灰铸铁gray iron; graphitic cast iron 过盈配合tight/interference fit缸套cylinder, sleeve, barrel tube pipe 导轨面guide way (face)铣刀盘face milling cutter/facing cutter 刀盘tool pan/cutter head磨削余量grinding allowance耐用性endurance钝化passivation刀尖圆弧circular profile of knife point(刀具)主偏角entering angle; plan angle弹性变形量amount of elastic deformation燃烧室combustion chamber磨屑abrasive dust滤器芯strainer core差速器differential gear反冲减震器recoiling shock absorber废气涡轮exhaust turbine涡轮增压器turbocharger增压盲区turboloch喷油器oil sprayer/atomizer汽化器carburetor硬质合金刀具carbide tipped tool精镗刀具fine boring tool动力传动系统power transmission systemspanner 扳子(美作:wrench)double-ended spanner 双头扳子adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子(美作:socket wrenchcalipers 卡规pincers, tongs 夹钳wire cutters 剪线钳multipurpose pliers, universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规hacksaw 钢锯grease gun 注油枪oil can 油壶边刨床side planer插床slotting machine车刀lathe tool车轮车床car wheel lathe车削turningBayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Belt drive 带传动Bending machines 弯曲机Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Crimping tools 卷边工具Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Etching machines 蚀刻机Honing machines 搪磨机Lapping machines 精研机Milling heads 铣头Mold polishing/texturing 模具打磨/磨纹Planing machines 刨床aberration 色差atomization 雾化bank mark 料纹bite 咬入blacking hole 涂料孔(铸疵)blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡centre buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷colour mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹表面处理关联用语时效硬化age hardening气体硬化air hardening空气韧化air patterning退火annealing阳极效应anode effect阳极氧化处理anodizing滚镀barrel plating滚筒打光barrel tumbling染黑法blackening青熟脆性blue shortness碳酸盐薄膜防锈法bonderizing 箱位退火box annealing封箱渗碳box carburizing辉面电镀bright electroplating 光辉热处理bright heat treatment旁路热处理bypass heat treatment 化学电镀chemical plating化学蒸镀chemical vapor deposition 大气热处理controlled atmosphere 锐角效应corner effect儒缓放电creeping discharge压花embossing部分淬火selective quenching。