成品AQL检验标准

Revision History修改记录
1. Scope范围
This document specifies the general quality requirements for the category of Furniture including domestic furniture, outdoor furniture and office furniture, etc. It is used as a general guideline for inspection if clients have not defined their requirement.
此文件为针对家具产品(包括室内家具,户外家具,办公家具等)验货的通用标准。

如果客户没有特别的要求，在此定为通用的验货指南。

2. Inspection Criteria of Product / Package产品/包装的验货标准
Reference standard: 引用标准
- EN1725, EN747-1/2, EN716-1/2, EN1130-1/2, EN1728, EN1022, EN12520, EN12521, EN1335-1/2/3, EN1730, EN527-1/2/3, EN581-1/2/3, BS4875-1/5/7, ISO7170, BS14749 - ASTM F 1427, BIFMA X5.1, BIFMA X5.5, ASTM F 1858, ASNI A 161.1
Product: 产品
✧Must be without any unsafe defect for using;
不允许有在实际使用中任何对使用者造成伤害的缺陷；
✧Should be free of damaged, broken, scratch, crackle etc. Cosmetic / Aesthetics defect;
不应有任何损坏，破碎，擦伤，或碎裂等外观缺陷；
✧Must be conform to the shipping market legal regulation / client’s requirement;
必须符合销往国当地的法规以及客户的要求；
✧The construction, appearance, cosmetics and material of all units should comply with
client’s requirement / approved samples;
产品的结构，外观，材料等必须符合客户的要求或与样品保持一致；
✧All units should have full function complying with client’s requirement / approved
samples;
产品功能必须符合客户的要求或与样品保持一致；
✧The marking / label on unit should be legal and clear.
产品上的标记/标签必须符合法规要求且清晰明确。

Package: 包装
✧All units will be adequately packaged, and constructed from suitably robust materials,
such that it arrives in store in a merchantable condition;
产品要有足够强度的材料构成的充分包装，使得货物以可销售的状态到达目的仓库；
✧The packaging material can protect the goods from damage during transportation;
在运输过程中，包装材料能防止货物受损；
✧The shipping mark, bar code, label (such as price label), should conform to client’s spec.
and/or approved samples;
箱麦，条形码，标签（例如：价格标签）应符合客户的要求或与样品保持一致；
✧The package should comply to client’s requirement / approved samples;
包装必须符合客户的要求或与样品保持一致；
✧Text of illustration, instruction, label and warning statement etc. must be clearly printed
in user’s langu age;
图解，说明书，标签，警告声明等应清晰地印有使用者语言；
✧The illustration and instruction on the packaging must conform to the product and its
actual performance.
包装上的图解和说明书必须与实际产品及其功能保持一致；
✧The method and material of pallet/crate etc. should be approved by client.
栈板/板条箱包装的材料及方式必须经客户批准
3. Inspection Plan & Defects classification检验计划及缺陷分类
Sampling procedure & Defects Definition, please refer to SHOP-HI001 General Inspection Operation Procedure
抽样程序以及缺陷定义，详见SHOP-HI001 通用检查程序–最终随机检查。

Acceptable Quality Limit: 可接受的质量限
✧Critical0 Non-conformity is not allowed ✧AQL 1.5 For Major Non-Conformity
✧AQL 4.0 For Minor Non-Conformity
For the other top, bottom, shelf, load uniformly with the load of 1.5kg/dm2 last for:
1 hour that made of metal, glass and stone;
4 hours that made of other materials.
对于其它尺寸的储物柜，在每一层均匀施加1.5
Any defect or loss serviceability
缺陷产生或功能丧失
Drawer strength test
抽屉的强度测试
Open the drawer to its open stops, or if there are no open stops, to the point at which one-third of the inside length (depth), or at least
Any defect or loss serviceability
缺陷产生或功能丧失
Note: 备注
The above described defects are those most commonly found, but not necessarily cover all possible defects.
以上缺陷描述是普遍存在的，但是可能未覆盖到所有的缺陷。

If the factory absence of some kinds of test equipment for the above mentioned field tests & data measurement items, then the inspector should be reported in our inspection report for the reference to client
如果工厂缺乏以上测量要求所必需的测试设备，验货员要在报告中注明，以供客户参考。