冲压模具制造检查表
合集下载
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
模具制造方代表:.
Construction Co. Rep
零件制造方代表:
Production Plant Rep.
冲压模具制造审核表（B）
DIE CONSTRUCTION REVIEW( B )
零件号:
Part Number
总成号:
Assembly Part#
工程更改号:
EWO#
零件名称:
Part Name
零件图纸号:
G D & T DWG #
零件图纸更改级别:
Part DWG E/C Level
年型/车型:
Year & Style
零件数模版本号:
Math Data Release #
模具编号:
Die Code
零件供应商:
Part Supplier
SQE ( SGM )
SQE ( SGM ):
电话:
Phone#
DUNS / Z编号:
DUNS / Z Code
模具工程师(供应商pplier)
电话:
D.冲孔头及引孔符合标准
Were the Pierce punch & punch entry as std.
E.斜锲操作平稳，回程装置安装正确
Camoperation is smooth, positive returns are fitted
14.模具的操作安全性
Is the safety cover installed properly
15.所有模具号标牌均正确固定，并按标准上漆
All die ID tags are fitted and painted as std.
注释:
Comments
批准人:
Approved by
模具工程师(供应商):
Die Engineer (Supplier)
SQE(SGM):
SQE(SGM):
日期
Date
模具制造方
DIE CONSTRUCTOR
模具工程师(供应商)
DIE ENGINEER
SQE
(SGM)
1.模具是否根据最新的数模制造?
Was die built to latest tool design & math data release level?
2.模具是否根据SGM最新的模具标准制造?
Was die built to latest SGM standards & construction tolerances?
D.最终的试模零件
Final try out sample
12.
成形（拉深、成形、弯曲、翻边、整形）Form(draw, form,
bend, flange, restrike )
A.所有模具表面应70%贴合
All die faces are matched 70%
B.压边圈、镶块接缝间隙及工作部分是否正确、完整?
Blank holder, insert steel gaps were correct and complete?
C.气垫位置及顶出高度检查
Cushion position and ejector stroke check
D.拉深模、成形模排气系统是否适合?
Are oil removing and air bleed appropriate for draw/form die?
13.
冲裁（落料、冲孔、切边）
Punch(blank, pierce, trim)
A.压料板接触面按标准为80%
Pad bearing is std. 80%
B.刃口间隙及切入量
The clearance and trim entrance for cut edge
C.镶块与安装座等的配合
Insert steel was matched with assembly retainer
7.所有压料、卸料及出件零件是否准确、适当?
Were die holder, stripper, lifter adequate and they functioned properly?
8.导向零件、支撑零件、连接零件是否完整、有效?
Are all guide, retainer, bolt, dowel etc. complete and functional?
Phone#
模具设计公司:
Die Design Co.
联系人:
Contact
电话:
Phone#
模具制造公司:
Die ConstructionCo.
联系人:
Contact
电话:
Phone#
零件制造地点:
Production Plant
联系人:
Contact
电话:
Phone#
冲压模具结构审核表
DIE CONSTRUCTION CHECK LIST
6.模具定位位置和尺寸是否正确，模具的定位装置与上模具有足够的间隙，与上料、卸料不干涉?
Was position and size of die location followed correctly, sufficient clearance between location and upper die, location will not interfere with load, unload?
11.
提供验证过的检测文件
Certification documentation is provided and verified
A.钢材的硬度检查
Steel hardness check
B.零件检测报告
Panel checking report
C.模具的静态和动态报告
Die Static check report and dynamic check report
3.合模高度
Die shut heigh
4.夹持螺栓的位置和尺寸
Were position and size of clamping slot adequate
5.板料定位装置是否稳定并可调，限位装置是否可靠?
Was panel location stable and adjustable, restrict reliability?
9.空气管接头及电气安装位置
Pneumatic connect and electric system location
10.用何种钢材制造模具；是否由材料供应商鉴定合格，按标准进行热处理? What type of tool steel was used and was it certified by the material supplier. Heat treatment as per standard?
Construction Co. Rep
零件制造方代表:
Production Plant Rep.
冲压模具制造审核表（B）
DIE CONSTRUCTION REVIEW( B )
零件号:
Part Number
总成号:
Assembly Part#
工程更改号:
EWO#
零件名称:
Part Name
零件图纸号:
G D & T DWG #
零件图纸更改级别:
Part DWG E/C Level
年型/车型:
Year & Style
零件数模版本号:
Math Data Release #
模具编号:
Die Code
零件供应商:
Part Supplier
SQE ( SGM )
SQE ( SGM ):
电话:
Phone#
DUNS / Z编号:
DUNS / Z Code
模具工程师(供应商pplier)
电话:
D.冲孔头及引孔符合标准
Were the Pierce punch & punch entry as std.
E.斜锲操作平稳，回程装置安装正确
Camoperation is smooth, positive returns are fitted
14.模具的操作安全性
Is the safety cover installed properly
15.所有模具号标牌均正确固定，并按标准上漆
All die ID tags are fitted and painted as std.
注释:
Comments
批准人:
Approved by
模具工程师(供应商):
Die Engineer (Supplier)
SQE(SGM):
SQE(SGM):
日期
Date
模具制造方
DIE CONSTRUCTOR
模具工程师(供应商)
DIE ENGINEER
SQE
(SGM)
1.模具是否根据最新的数模制造?
Was die built to latest tool design & math data release level?
2.模具是否根据SGM最新的模具标准制造?
Was die built to latest SGM standards & construction tolerances?
D.最终的试模零件
Final try out sample
12.
成形（拉深、成形、弯曲、翻边、整形）Form(draw, form,
bend, flange, restrike )
A.所有模具表面应70%贴合
All die faces are matched 70%
B.压边圈、镶块接缝间隙及工作部分是否正确、完整?
Blank holder, insert steel gaps were correct and complete?
C.气垫位置及顶出高度检查
Cushion position and ejector stroke check
D.拉深模、成形模排气系统是否适合?
Are oil removing and air bleed appropriate for draw/form die?
13.
冲裁（落料、冲孔、切边）
Punch(blank, pierce, trim)
A.压料板接触面按标准为80%
Pad bearing is std. 80%
B.刃口间隙及切入量
The clearance and trim entrance for cut edge
C.镶块与安装座等的配合
Insert steel was matched with assembly retainer
7.所有压料、卸料及出件零件是否准确、适当?
Were die holder, stripper, lifter adequate and they functioned properly?
8.导向零件、支撑零件、连接零件是否完整、有效?
Are all guide, retainer, bolt, dowel etc. complete and functional?
Phone#
模具设计公司:
Die Design Co.
联系人:
Contact
电话:
Phone#
模具制造公司:
Die ConstructionCo.
联系人:
Contact
电话:
Phone#
零件制造地点:
Production Plant
联系人:
Contact
电话:
Phone#
冲压模具结构审核表
DIE CONSTRUCTION CHECK LIST
6.模具定位位置和尺寸是否正确，模具的定位装置与上模具有足够的间隙，与上料、卸料不干涉?
Was position and size of die location followed correctly, sufficient clearance between location and upper die, location will not interfere with load, unload?
11.
提供验证过的检测文件
Certification documentation is provided and verified
A.钢材的硬度检查
Steel hardness check
B.零件检测报告
Panel checking report
C.模具的静态和动态报告
Die Static check report and dynamic check report
3.合模高度
Die shut heigh
4.夹持螺栓的位置和尺寸
Were position and size of clamping slot adequate
5.板料定位装置是否稳定并可调，限位装置是否可靠?
Was panel location stable and adjustable, restrict reliability?
9.空气管接头及电气安装位置
Pneumatic connect and electric system location
10.用何种钢材制造模具；是否由材料供应商鉴定合格，按标准进行热处理? What type of tool steel was used and was it certified by the material supplier. Heat treatment as per standard?