Honda CB1000RA Accessory Socket 安装说明书

Publication No.
MII 16775
Issue Date
August 2018
PARTS LIST
1. Remove the passenger seat as shown.
PASSENGER SEAT
(1)
(2) (3)
(4)
No.
Description
Qty
(1)
Accessory socket
2. Remove the main seat and disconnect the negative (-) cable of the battery.
BOLT
WASHER
MAIN SEAT
© 2018 American Honda Motor Co., Inc. - All Rights Reserved.
• Disconnect the negative (-) cable from the battery before installing this accessory.
• The memory of the clock will be erased when you disconnect the battery. Reset the clock after reconnecting the battery.
• Reinstall the removed parts on the motorcycle and make sure that the wires and harnesses are not pinched.
• Cut the wire tie at 5 mm from the lock part after attaching them to the wire harnesses. Do not allow the cut part of the wire tie to interfere with another harness or brake hose.
COVER
ACCESSORY SOCKET STAY
ACCESSORY SOCKET STAY
NUT (Reuse)
PROJECTION
ACCESSORY SOCKET
11. Install the cover as shown.
9. Remove the nut as shown.
ACCESSORY SOCKET
INSTALLATION
CAUTION • To prevent burns, allow the engine, exhaust system,
radiator, etc., to cool before installing the accessory.
NOTE:
• Refer to this manual and the Meter Visor Installation Instruction when the motorcycle is equipped with the Meter visor.
COLLAR
BOLT
HEADLIGHT
When installing the Meter visor
BOLT
2 of 5
7. Loosely install the bolt and collar as shown. • Perform this step for the motorcycle equipped with the meter visor. • Repeat on the right side.
1
(2)
Wire tie socket stay
1
(4)
Installation Instruction URL
1
TORQUE CHART
Refer to the Service Manual for the torque values of the removed parts.
10. Assemble the accessory socket as shown.
Install the cap in the direction as shown. CAP
COLLAR (Reuse)
BOLT (Reuse)
8. Move the cover as shown.
ACCESSORY SOCKET
Accessory
Application
INSTALLATION INSTRUCTIONS
ACCESSORY SOCKET P/N 08U72-MKJ-D00
CB1000RA
Honda Dealer: Please give a copy of these instructions to your customer.
NUT
COVER (Reuse) ACCESSORY SOCKET
3 of 5
12. Remove the dummy connector as shown.
2-PIN WATERPROOF DUMMY CONNECTOR (Black) (Save)
14. Install the assembled accessory socket as shown.
BOLT
COLLAR
BOLT
16. Install the collars to the headlight in the reverse order of removal.
• Repeat on the right side.
• Perform this step for the motorcycle equipped with the meter visor.
BOLT (Reuse)
ASSEMBLED ACCESSORY SOCKET
When installing the Meter visor
RIGHT METER VISOR STAY
LEFT METER VISOR STAY
BOLT (Reuse)
ASSEMBLED ACCESSORY SOCKET
15. Remove the bolt and collar as shown. • Perform this step for the motorcycle equipped with the meter visor. • Repeat on the right side.
LEFT METER VISOR STAY
• Confirm that any wire harness is not caught or too tight.
MOTORCYCLE’S 2-PIN WATERPROOF CONNECTOR (Black)
13. Remove the bolts as shown.
BOLT
When installing the Meter visor
1 of 5
72MKJ040
3. Remove the meter visor as shown.
• Perform this step for the motorcycle equipped with the meter visor.
5. Remove the headlight as shown.
4 of 5
17. Route and connect the accessory socket harness as shown.
2-PIN WATERPROOF ACCESSORY CONNECTOR (Black) SOCKET HARNESS
18. Secure the accessory socket harness with the wire tie as shown.
ACCESSORY SOCKET HARNESS WIRE TIE Secure the accessory socket harness to the motorcycle’s harness.
19. Install the motorcycle’s parts in the reverse order of removal. • Confirm that any wire harness is not caught or too tight.
20. Check the accessory socket, headlight and the other lights for proper operation. 5 of 5
HEADLIGHT Disconnect the connector.
WASHER (Black) BOLT
WASHER (White)
METER VISOR
4. Remove the bolt as shown. • Repeat on the right side.
<Left side>
6. Remove the collars as shown. • Perform this step for the motorcycle equipped with the meter visor.