海洋石油钻井英语手册
教材：石油钻井常用英语手册
A Handbook of English for Oil Drilling石油钻井常用英语手册职工培训教材系列辽河石油勘探局钻井二公司六分公司二OO七年四月A Handbook of English for Oil Drilling石油钻井常用英语手册一、DRILLING 钻井1.Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业.2.Prepared bell nipple. 准备”喇叭口”短节.3.Make up 2 joints of drill pipe. 接两根钻杆.4.Break out this connection. 卸开该接头.5.Make up bottom hole assembly. 组合下部钻具6.Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.7.Number stands on trip out and trip in. 起下钻时给立柱编号.8.Pick up BHA and run to seafloor. 将下部钻具下到海底.9.Pick up stands. 接立柱10.Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱11.Drop TOTCO. 投(陶特)测斜仪12.Fish TOTCO with overshot. 用打捞筒捞起测斜仪13.Resume drilling to T.D. 继续钻进到总深14.Circulate 15 minutes.循环15分钟15.Run in hole. 下钻16.Put out of hole. 起钻17.Make an inventory of all ring gaskets. 开一个所有垫圈的清单e spinning tong. 使用气动扳手19.Operate the air winch. 操作气动绞车y down 57 joints of 5” drill pipe. 甩57根钻杆21.Pick up drill stem test tool. 提起钻杆测试工具22.Circulate mud for 2 hours. 循环泥浆2小时23.Move string during circulation. 在循环时注意活动钻具24.Circulate hole clean. 循环清洗井眼25.Circulate bottoms up. 循环泥浆几周26.Fill up every 5 stands. 每5柱灌泥浆一次27.Check mud weight every 15 minutes. 每15分钟检查泥浆比重28.Reverse out excess cement. 反循环替出多余的泥浆29.Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆30.Stop drilling. 停止钻进31.Drilling ahead. 钻进32.Pull out of hole bit. 起出钻头33.Change bit. 换钻头34.Run the wear bushing. 下抗磨补心35.The bit thread type is regular pin. 钻头丝扣是正规公扣36.What’s the make-up torque? 上扣扭矩要多大?37.Run in 9” collars. 下9”钻铤38.The cathead ca n’t give enough torque. 猫头力量不够39.Connect crossover sub. 接上配合接头40.The tong angle is too small. 大钳的角度太小了41.Stop circulating. 停止循环泥浆42.Break out the stand. 卸立柱43.Set the single into the mousehole. 把这个单根放进鼠洞44.Can we break out the pipe with rotary table? 可用转盘卸扣吗?45.No! Break it out with tong. 不行! 要用大钳卸扣46.Spin it out with the air spanner. 用气动扳手卸扣47.Put the pipe wiper on the string. 装上钻杆刮泥器48.Don’t set this stand back. 这根钻杆不要放在钻杆盒上49.Make up the lift sub. 接好提升短节50.Secure the safety clamp. 上紧安全卡瓦51.The bit is nearing the shoe. 钻头快到套管鞋了52.Slow down the running speed. 放慢下放速度53.This is the undergauged interval. 这是缩径井段54.This is the drilling program. 这是钻井设计书55.How much weight on bit is required? 要加多少钻压?56.Keep the rotary speed at 120---140 RPM. 转速保持120---140转/分57.Keep the flow rate at 3000 LPM. 保持排量3000升/分58.The pump pressure is too high. 泵压太高了59.Don’t ream the hole too fast. 划眼不要太快60.Notice the rotary torque. 注意转盘扭矩的变化61.The penetration rate is getting slower. 钻速变慢了62.The bit is nearly worn out. 钻头快磨光了63.Stop drilling at 2000 meters. 钻至2000米停钻64.Circulate for one hour. 循环一个小时65.The pump pressure has increased. 泵压升高了66.One nozzle may be plugged. 可能有一个水眼(或: 喷嘴)堵了67.What is the hook load? 悬重多少?68.What’s the pick-up weight? 上提重量是多少?69.What’s the lowering weight? 下放重量是多少?70.Run in HWDP. 下加重钻杆71.A stabilizer is needed here. 这里需要一个扶正器72.This is a flexible sub. 这是挠性接头73.This is the BHA log. 这是下部钻具组合记录74.Record all outside and inside diameters. 记录好所有(入井工具的)内外径75.We need a short drill collar. 需要一根短钻铤76.Pull the cat line. 拉猫头77.Operate the break lever. 操作(或:扶)刹把78.Stop the pumps. 停泵79.Make a wiper trip. 通井80.Retrieve wear bushing. 取出抗磨补心81.Bleed off pressure. (释)放压(力)82.Keep 5 wraps on the drum. 滚筒上留5圈83.Set slips. 座上卡瓦84.If tight hole, repeat wiper trip. 如果井眼紧, 重复划眼85.Setback bottom hole assembly. 将下部钻具立于钻杆盒内86.Make sure all alarms are on. 确保所有的警报信号都开着y down TDS spinner. 拆下顶部驱动的旋扣器88.Run in hole bit #15 to bottom. 用15号钻头下钻到井底89.Run in hole to casing shoe. 下钻至套管鞋90.Pick up same bit and BHA. 装上同样的钻头和钻具组合y down 5” HW drill pipe. 甩5”加重钻杆92.Move string every 2 hours. 每2小时活动钻具一次93.Keep area around shaker clean. 保持振动筛区域干净94.Control trip gas. 控制起下钻气95.Ream if needed. 如必要时进行划眼96.Select the best penetration rate. 选择最佳钻进速度97.Fix the traveling assembly. 固定游动系统98.Check power tongs and spinning rope are on drill floor. 检查动力钳和尾绳是否在钻台99.What’s the we ight on bit? 钻压是多少?100.What is the BHA of this well? 这口井的下部钻具如何组合?101.Drill out cement. 钻穿水泥102.Drill out 20” casing shoe. 钻穿20”套管鞋tch the elevator. 扣吊卡104.Unlatch the elevator. 开吊卡105.Set the slips. 放卡瓦106.Adjust the crown-o-matic (crown saver). 调整防碰天车107.Lock the hook pin. 锁紧大钩销子108.Check OD of stabilizer. 检查扶正器的外径109.Perform leak off test. 进行地层破裂(或:渗漏)测试110.Connect kill and choke line. 接上压井和放喷管线111.Reverse out the drill pipe. 反循环清洗钻杆112.Make a short trip. 进行短途起下钻113.Change the cutters. 换割刀114.Slug the pipe. 灌重泥浆115.Drill the stand down. 钻完立柱116.Start/run the shale shaker. 开振动筛117.Start the desanders. 开除砂器118.Start the desilters. 开除泥器119.Change it with a 40 mesh screen. 换成40目筛布120.Shut it off. 关掉121.Pull it to the cat ramp. 把它拉到坡道上去122.Make a fast connection. 接单根要快123.Don’t dump the mud into the s ea. 不要把泥浆排放到海里124.Disconnect it with a chain tong. 用链钳卸开125.Put a thread protector. 加一个(丝扣)护箍126.Can we use the power slips? 可以使用动力卡瓦吗?二、CASING AND CEMENTING 下套管与固井127.R un in hole to bottom for wiper trip. 下钻通井128.T his is the casing program. 这是套管程序129.P repare for running casing. 准备下套管130.M ake everything ready for running 7”casing. 做好下7”套管的准备131.M ake cementing job. 固井132.D isplace cementing with mud pump. 用泥浆泵替泥浆133.S et cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞134.P ick up cementing head. 接水泥头135.C ement samples are hard. 水泥样已凝固136.P ump in 3 cubic meters of spacer. 注3方隔离液137.P ump down the plug. 泵压(胶)塞138.W ait on cement. 候凝139.T he guide shoe will be connected. 接引鞋140.C onnect the floor collar. 接浮箍141.C onnect the air line to the casing stabbing board. 接好套管扶正台的气管线142.R un casing with the 350T slip elevator. 用350吨卡瓦式吊卡下套管143.C lean and dry 20” casing threads with rags. 清洁并擦干20”套管丝扣144.W here is the rabbit for drifting the casing? 套管通径规在哪里?三、FISHING 打捞145.The bit cutters have been lost in the hole. 牙轮落井146.Run in the reverse-circulation basket. 下反循环打捞篮147.There is a lot of junk in the hole. 井下有很多落物148.The fish is 235.46 meters long. 落鱼长度235.46米149.The fish top is at 2478.34 meters. 鱼顶位置2478.34米四、FREEING STUCK PIPE 卡钻与解卡190.The down-hole problems are very complicated. 井下情况很复杂191.The hole is tight. 遇阻了192.Overpull while tripping out. 起钻遇卡(overpull: 超拉力)193.The formation is unstable. 地层不稳定194.The wall caving is severe. 井壁垮塌严重195.There are many return cuttings. 返出岩屑特别多196.The mud returns have decreased. 返出泥浆减少197.The hole is enlarged. 井眼扩大了198.The pipe’s stuck. 卡钻了199.Pull up to 150 tons. 上提150吨200.Slack off to 50 tons. 下放至50吨201.Ream down all the tight points. 在所有遇阻点进行划眼202.The rotary table can’t rotate. 转盘转不动203.Where is the sticking point? 卡点在哪里204.Make a tensile test. 做拉伸试验205.Back it off above the free point. 在卡点以上倒扣206.Where is the back-off position? 脱扣位置在哪207.Plug the well for side tracking. 打水泥塞侧钻五、ABNORMAL WELL CONDITION AND WELL CONTROL异常井况与压井168.The mud is gas out. 泥浆有气侵169.The pit has lowered quickly. 泥浆池液面下降很快170.The hole lost returns. 井口不返泥浆171.The returns are unstable. 返出泥浆量忽大忽小172.Where’s the thief zone? 漏失层在哪里173.Cut down the flow rate. 降低排量174.Lower the mud density. 降低比重175.Cut down the hydrostatic pressure. 减少静压176.The gas smell is strong. 天然气味度很浓177.There’s some trace of oil. 发现有油花178.The pump pressure is fluctuating. 泵压不稳179.It is a zone of abnormal pressure. 这是异常压力层180.The hole (well) is kicking! 井涌啦!181.Shut in the BOP! 关闭防喷器182.Sound the general alarm quickly! 快发出综合警报183.The stand pipe pressure is 10 kg/cm2. 立管压力10公斤/厘米2184.The casing pressure is 25 kg/cm2. 套压2510公斤/厘米2185.Fill out the kill sheet. 填写压井记录表186.Kill the well. 压井187.Ther e’s a combination of lost returns and the kick. 又喷又漏, 情况复杂188.Reverse the gas out of the hole. 反循环排气189.What’s the lag time? 迟到时间是多少190.The well is now stable. 现在井眼已经稳定六、PREPERATION BEFORE MAKING HOLE钻前准备191.Tell the mechanic to check the motor torque . 让机械师检查马达扭矩。
钻井英语手册2319
A Handbook of English for Oil Drilling一.承包商人员( Contractor’s Personnel )Rig Manager 平台经理Equipment Supervisor 设备总监Materials Supervisor 材料总监Senior Toolpusher 高级队长Junior Toolpusher 值班队长Driller 司钻Assistant Driller (AD) 副司钻Derrick Man 井架工Floor Man (roughneck) 钻工Crane Operator吊车工Mechanic 机械师Electrician 电气师Repairman 修理工Welder 焊工Warehouse Man (stock Keeper) 材料员Safety Supervisor 安全监督Interpreter (translator) 翻译Chief Steward 管事Cook 厨师Steward厨工Laundry Man洗衣工clean boy (清洗工) 常用于井队现场雇用外籍清洁员。
二.作业者及服务公司人员(Operator’s Personnel and Service Company Personnel) Drilling Superintendent 钻井监督Company Man (Operator’s Representative) 公司代表Geologist 地质师Mud Logging Engineer (Mud logger) 泥浆录井工程师Sample Catcher捞砂工Mud Engineer 泥浆工程师Cementer 固井工Cement Engineer 固井工程师Testing Engineer 试油工程师Coring Engineer 取芯工程师Wireline Logging Engineer电测工程师三.钻井设备(Drilling Equipment) Drawworks 钻井绞车Rotary Table 转盘Bushing 补心Top Drive System (TDS) 顶驱Swivel 水龙头Crown Block 天车Traveling Block 游车Hook 大钩Derrick 井架Pipe Spinning Wrench 钻杆气动扳手Ezy-Torq 液压猫头Elmagco Brake 涡磁刹车Pipe handling Equipment 钻杆移动设备Iron roughneck 铁钻工Pipe Racking System 钻杆排放系统Drill String 钻柱Drilling Sub 钻井短节Fishing Tool 打捞工具Power Tong 动力大钳Air Winch (air tugger) 气动绞车Crown-O-Matic (Crown Saver) 防碰天车四.泥浆系统(Mud System)Mud Pump 泥浆泵Shale shaker 振动筛Mud Cleaner 泥浆清洁器Desilter 除泥器Desander 除砂器Degasser 除气器Centrifuge 离心机Mud Agitator 泥浆搅拌器Mud Mixing System 泥浆混合系统Centrifugal Pump 离心泵Standpipe Manifold立管管汇Rotary Hose 水龙带Bulk Air System and Tank吹灰系统和灰罐五.井控设备(Well Control Equipment) Ram Type Preventor 闸板防喷器Annular Type Preventor 万能防喷器BOP Stack 防喷器组Gate Valve 闸阀Choke and Kill Manifold 阻流压井管汇Remotely Operated Panel 远程控制面板Choke Control Panel 阻流控制面板BOP Handling Equipment 防喷器搬运设备Diverter 转喷器六.机房(Engine Room)Diesel Engine 柴油机Emergency Generator 应急发电机Air Compressor 空气压缩机Boiler 锅炉Air-conditioning System 空调系统Piping System 管汇系统Generator 发电机Transformer 变压器DC Motor 直流马达AC Motor 交流马达七.安全设备(Safety Equipment)Fire Control System 消防控制系统Fire Detection System 火情探测系统CO2 System 二氧化碳系统Fixed Fire Extinguishing System 固定消防系统Portable Extinguisher 移动灭火器Fire-Fight Equipment 消防设备Foam System 泡沫系统Escape Routes 逃生路线Breathing Apparatus 呼吸器Gas Detection System 气体探测系统Helicopter Facility 直升机设施Sick-Bay (Hospital) 医务室Pollution Control 防污控制八.其他( Others)Cementing Unit 固井装置Well Testing Equipment 试油设备Mud Logging Unit 泥浆录井房Wire Logging Unit 电测装置Meter 米Foot 英尺Inch 英寸Day (night) Shift 白(夜)班Crew Change倒班Position 岗位Evacuation撤离Rig 钻机Quarters (living quarters, accommodation area) 生活区Drill Floor (Rig floor) 钻台Control Room 控制室Air Compressor Room 空气压缩机房BOP Control Room控制房Engine Room 机房Warehouse (Store) 材料库房Sack Storage Area 散装材料储存区Mud pit 泥浆池Riser Rack Area 隔水管排放区Pipe Rack Area 钻杆排放区Pipe Slide滑道Ramp坡道Pump Room 泵房Coffee Room 咖啡室Mess (dining) Room 餐厅Recreation Room 娱乐房TV RoomChange Room工衣房Kitchen 厨房附录四. 钻具,井口工具,打捞工具Drill Pipe 钻杆Drill Collar 钻铤H eavy W eight D rill P ipe 加重钻杆Elevator 吊卡Tong 大钳Make-up Tong 上扣大钳Break-out Tong 卸扣大钳Mud Box泥浆防喷盒Casing Stabbing Board套管扶正器Slips 卡瓦Spider卡盘(蜘蛛)Mouse Hole 小鼠洞(接单根用) Kelly Spinner 方钻杆旋转器Kelly Cock 方钻杆阀Chain Tong 链钳Casing 套管Tubing 油管Drill String 钻柱Jar (drilling jar) 震击器Right Hand Thread 正扣Left Hand Thread 反扣Stabilizer 扶正器Stabilize(v稳定) Liner 尾管Conductor 导管Thread Protector 护丝Stand (钻杆) 立柱Single (钻杆) 单根Joint (钻具) 根Bend弯头Sub 短节Pup Joint 短钻杆, 短节Connector 接头Bit 钻头Bit Breaker 钻头盒Box 母扣Pin公扣Hole Opener 开眼钻头Reamer 扩眼钻头Overshot打捞筒Junk Basket打捞篮Junk Mill 平头磨鞋Spear 打捞矛Fishing Tap 打捞公锥Cross Over Sub (XO Sub) 转换接头Bottom Hole Assembly (BHA) 下部钻具组合附录五. 材料和工具Steel 钢Iron 铁Wood 木Chemicals 化学品Cement 水泥Barite 重晶石Fuel 柴油Helifuel 飞机燃油Lubricant (Lube/Lube oil) 润滑油Grease 黄油Thread Dope 丝扣油Gasoline 汽油Mud 泥浆Bentonite 般土Additive 添加剂Caustic Soda烧碱Weight Material 加重材料Thinner 稀释剂Oxygen 氧气Nitrogen 痰气Hydrogen Sulphide 二氧化硫Acetylene乙炔Compressed Air 压缩空气Hydraulic Fluid 液压油Spanner 扳手Hammer 铁锤Screw Driver 螺丝刀Multi meter 万用表Welding Machine 焊机Bar 撬杠Shackle卸扣Sling (钢丝) 绳套Container 集装箱附录六. 常用缩写形式BHA: bottom hole assembly 下部钻具组合DP: drill pipe 钻杆DC: drill collar 钻铤HWDP: heavy weight drill pipe 加重钻杆BOP: blowout preventer 防喷器TD: total depth总深TVD: true vertical depth (定向井的)垂直深度SCR: silicon controlled rectifier 可控硅OD: outside diameter 外径ID: inside diameter 内径BBL: barrel 桶LB: (拉丁语) Libra=pound (重量单位) PSI: p ound per s quare i nch 磅/英寸2 GAL: gallon 加仑POOH: p ull o ut o f h ole 起钻RIH: r un i n h ole 下钻WOC: wait on cement候凝RPM: revolution p er m inute 转速/分钟LPM: liter per minute 升/分钟SWL: safe working load安全工作负荷API: American Petroleum Institute 美国石油协会IADC: international association of drilling contractors 国际钻井承包商协会MPI: magnetic particle inspection磁粉探伤附录七:常用语Drilling 钻井Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业.Prepared bell nipple. 准备”喇叭口”短节.Make up 2 joints of drill pipe. 接两根钻杆.Break out this connection(joint). 卸开该接头.Run hole opener to sea bed. 下扩眼器到海底Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆.Make up bottom hole assembly. 组合下部钻具Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.Number stands on trip out and trip in. 起下钻时给立柱编号.Pick up BHA and run to seafloor. 配下部钻具将其下到海底.Pick up stands. 接立柱Don’t drill faster than 15 minute s for 1 stand. 钻进速度别超过15分钟1根立柱Drop TOTCO. 投(陶特)测斜仪Fish TOTCO with overshot. 用打捞筒捞起测斜仪Resume drilling to T.D. 继续钻进到总深Circulate 15 minutes.循环15分钟Run in hole. 下钻Put out of hole. 起钻Make an inventory of all ring gaskets. 开一个所有垫圈的清单Use spinning tong. 使用气动扳手Operate the air winch. 操作气动绞车Lay down 57 joints of 5” drill pipe. 甩57根钻杆Pick up drill stem test tool. 提起钻杆测试工具Circulate mud for 2 hours. 循环泥浆2小时Move string during circulation. 在循环时注意活动钻具Circulate hole clean. 循环清洗井眼Circulate bottoms up. 循环泥浆几周Fill up every 5 stands. 每5柱灌泥浆一次Check mud weight every 15 minutes. 每15分钟检查泥浆比重Reverse out excess cement. 反循环替出多余的泥浆Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆Stop drilling. 停止钻进Drilling ahead. 钻进Pull out of hole bit. 起出钻头Change bit. 换钻头Run the wear bushing. 下抗磨补心The bit thread type is regular pin. 钻头丝扣是正规公扣What’s the make-up torque?上扣扭矩要多大?Run in 9” collars. 下9”钻铤The cathead can’t give enough torque. 猫头力量不够Connect crossover sub. 接上配合接头The tong angle is too small. 大钳的角度太小了Stop circulating. 停止循环泥浆Break out the stand. 卸立柱Set the single into the mousehole. 把这个单根放进鼠洞Can we break out the pipe with rotary table? 可用转盘卸扣吗? No! Break it out with tong. 不行! 要用大钳卸扣Spin it out with the air spanner. 用气动扳手卸扣Put the pipe wiper on the string. 装上钻杆刮泥器Don’t set this stand back. 这根钻杆不要放在钻杆盒上Make up the lift sub.接好提升短节Secure the safety clamp. 上紧安全卡瓦The bit is nearing the shoe. 钻头快到套管鞋了Slow down the running speed. 放慢下放速度This is the undergauged interval. 这是缩径井段This is the drilling program. 这是钻井设计书How much weight on bit is required? 要加多少钻压?Keep the rotary speed at 120---140 RPM. 转速保持120---140转/分Keep the flow rate at 30.00 LPM. 保持排量30升/分The pump pressure is too high. 泵压太高了Don’t ream the hole too fast. 划眼不要太快Notice the rotary torque. 注意转盘扭矩的变化The penetration rate is getting slower. 钻速变慢了The bit is nearly worn out. 钻头快磨光了Stop drilling at 2000 meters. 钻至2000米停钻Circulate for one hour. 循环一个小时The pump pressure has increased. 泵压升高了One nozzle may be plugged. 可能有一个水眼(或: 喷嘴)堵了What is the hook load? 悬重多少?What’s the pick-up weight? 上提重量是多少?What’s the lowering weight? 下放重量是多少?Run in HWDP. 下加重钻杆A stabilizer is needed here. 这里需要一个扶正器This is a flexible sub. 这是挠性接头This is the BHA log. 这是下部钻具组合记录Record all outside and inside diameters. 记录好所有(入井工具的)内外径We need a short drill collar. 需要一根短钻铤Pull the cat line. 拉猫头Operate the break lever. 操作(或:扶)刹把Stop the pumps. 停泵Make a wiper trip. 通井Retrieve wear bushing. 取出抗磨补心Bleed off pressure. (释)放压(力)Keep 5 wraps on the drum. 滚筒上留5圈Set slips. 座上卡瓦If tight hole, repeat wiper trip. 如果井眼缩径, 重复划眼Setback bottom hole assembly. 将下部钻具立于钻杆盒内Make sure all alarms are on. 确保所有的警报信号都开着Lay down TDS spinner. 拆下顶部驱动的旋扣器Run in hole bit #15 to bottom. 用15号钻头下钻到井底Run in hole to casing shoe. 下钻至套管鞋Pick up same bit and BHA. 装上同样的钻头和钻具组合Lay down5” HW drill pipe. 甩5”加重钻杆Move string every 2 hours. 每2小时活动钻具一次Keep area around shaker clean. 保持振动筛区域干净Control trip gas. 控制起下钻气Ream if needed. 如必要时进行划眼Select the best penetration rate. 选择最佳钻进速度Fix the traveling assembly.固定游动系统Check power tongs and spinning rope are on drill floor. 检查动力钳和尾绳是否在钻台What’s the weight on bit? 钻压是多少?What is the BHA of this well? 这口井的下部钻具如何组合?Drill out cement. 钻穿水泥Drill out 20” casing shoe. 钻穿20”套管鞋Latch the elevator. 扣吊卡Unlatch the elevator. 开吊卡Set the slips. 放卡瓦Adjust the crown-o-matic (crown saver). 调整防碰天车Lock the hook pin. 锁紧大钩销子Check OD of stabilizer. 检查扶正器的外径Perform leak off test. 进行地层破裂(或:渗漏)测试Connect kill and choke line. 接上压井和放喷管线Reverse out the drill pipe. 反循环清洗钻杆Make a short trip. 进行短途起下钻Change the cutters. 换割刀Slug the pipe. 灌重泥浆Drill the stand down. 钻完立柱Start/run the shale shaker. 开振动筛Start the desanders. 开除砂器Start the desilters. 开除泥器Change it with a 40 mesh screen. 换成40目筛布Shut it off. 关掉Pull it to the cat ramp. 把它拉到坡道上去Make a fast connection. 接单根要快Don’t dump the mud to the wellsite. 不要把泥浆排放到井场Disconnect it with a chain tong. 用链钳卸开Put a thread protector.加一个(丝扣)护箍Can we use the power slips? 可以使用动力卡瓦吗?Casing and Cementing 下套管与固井Run in hole to bottom for wiper trip. 下钻通井This is the casing program. 这是套管程序Prepare for running casing. 准备下套管Make everything ready for running 7”casing. 做好下7”套管的准备Make cementing job. 固井Displace cementing with mud pump. 用泥浆泵替泥浆Set cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞Pick up cementing head.接水泥头Cement samples are hard. 水泥样已凝固Pump in 3 cubic meters of spacer.注3方隔离液Pump down the plug. 泵压(胶)塞Wait on cement. 候凝The guide shoe will be connected. 接引鞋Connect the floor collar. 接浮箍Connect the air line to the casing stabbing board. 接好套管扶正台的气管线Run casing with the 350T slip elevator. 用350吨卡瓦式吊卡下套管Clean and dry 20” casing threads with rags. 清洁并擦干20”套管丝扣Where is the rabbit for drifting the casing? 套管通径规在哪里? How much is the horse power? 有多大马力?She has 6000 HP. 有6000马力Unleash the drilling tools. 卸开钻具Tighten up. 绷紧(或:上紧)一点Fishing 打捞The bit cutters have been lost in the hole. 牙轮落井Run in the reverse-circulation basket. 下反循环打捞篮There is a lot of junk in the hole. 井下有很多落物The fish is 235.46 meters long. 落鱼长度235.46米The fish top is at 2478.34 meters. 鱼顶位置2478.34米Coring 取芯Stop drilling for coring. 停钻准备取芯Make up core bit. 接取芯钻头What type of core bit is it? 这是什么型号的取芯钻头?Run in a diamond core bit. 下金刚石取芯钻头Let’s drop the ball for coring. 可以投球取芯The core has been broken off. 岩芯断了Put the core in the boxes. 把岩芯装在岩芯盒里Don’t brake suddenly. 不要猛刹车Take out the core. 岩芯出筒How long is the core? 岩芯多长The core recovery is 98%. 岩芯收获率是98%Run in the core barrel again. 继续下岩芯筒(或: 取芯筒)Run in hole core barrel. 下取芯筒Drop ball. 投钢球Recover core. 取出岩芯Use same parameters as for core #1.使用与1#取芯同样的参数Freeing Stuck Pipe 卡钻与解卡The down-hole problems are very complicated. 井下情况很复杂The hole is tight. 遇阻了Overpull while tripping out. 起钻遇卡(overpull: 超拉力) The formation is unstable. 地层不稳定The wall caving is severe. 井壁垮塌严重There are many return cuttings. 返出岩屑特别多The mud returns have decreased. 返出泥浆减少The hole is enlarged. 井眼扩大了The pipe’s stuck. 卡钻了Pull up to 150 tons. 上提150吨Slack off to 50 tons. 下放至50吨Ream down all the tight points. 在所有遇阻点进行划眼The rotary table can’t rotate. 转盘转不动Where is the sticking point? 卡点在哪里Make a tensile test. 做拉伸试验Back it off above the free point. 在卡点以上倒扣Where is the back-off position? 脱扣位置在哪Plug the well for side tracking. 打水泥塞侧钻Abnormal Well Condition and Well Control异常井况与压井The mud is gas out. 泥浆有气侵The pit has lowered quickly. 泥浆池液面下降很快The hole lost returns. 井口不返泥浆The returns are unstable. 返出泥浆量忽大忽小Where’s the thief zone? 漏失层在哪里Cut down the flow rate. 降低排量Lower the mud density. 降低比重Cut down the hydrostatic pressure. 减少静压The gas smell is strong. 天然气味度很浓There’s some trace of oil. 发现有油花The pump pressure is fluctuating. 泵压不稳It is a zone of abnormal pressure. 这是异常压力层The hole (well) is kicking! 井涌啦!Shut in the BOP! 关闭防喷器Sound the general alarm quickly! 快发出综合警报The stand pipe pressure is 10 kg/cm2. 立管压力10公斤/厘米2The casing pressure is 25 kg/cm2. 套压2510公斤/厘米2Fill out the kill sheet. 填写压井记录表Kill the well. 压井There’s a combination of lost returns and the kick. 又喷又漏, 情况复杂Reverse the gas out of the hole. 反循环排气What’s the lag time? 迟到时间是多少The well is now stable. 现在井眼已经稳定BOP and subsea Equipment 防喷器与水下设备Cut off the 30” conductor. 割掉30”隔水管Weld on the 30” bottom flange. 焊接30”法兰Hoist and nipple up 30” diverter. 吊装30”转喷器Change the 5” pipe rams to 3-1/2” rams. 把这个5”闸板换成3-1/2” Install blind ram. 安装防喷器的盲板芯子Check the seal ring of the conductor. 检查隔水管密封圈Cut off the lifting eye of the conductor. 切割隔水管耳环Test BOP. 测试防喷器Change annular BOP packing. 更换万能防喷器芯子Full pressure test the ram preventers. 对闸板防喷器进行全压试压Test annular BOP at 2500psi. 万能防喷器试压至2500psiCheck annular pressure. 检查环形空间压力Confirm the angle of the guide base. 确定基板角度The thread is covered with the quick-release protectors. 已戴好快卸护丝Establish the guide lines. 装导向绳Connect the TGB running tool. 接临时导向基板送入工具Land the TGB to sea. 下临时导向基板到海底Retrieve the running tool. 退出送入工具Run the BOP and risers. 下防喷器和隔水管Pick up the marine riser. 吊出隔水管Pick up the slip joint. 起伸缩节Adjust the riser tensioners. 调整隔水管张力Function test the diverter system. 对防喷器系统进行功能测试Retrieve the pin connector. 取出销钉连接器Run the test plug. 下试压塞Close the upper pipe ram. 关上部钻杆闸板防喷器Open the kill line valve. 开压井管线阀The compensation capacity is 400000 pounds. 补偿能力是400千磅The locking load is 1000000 pounds. 锁紧负荷1000千磅Land the BOP onto the well head. 座防喷器到井口头BOP carrier. 防喷器叉车Check for junk inside shoe joint. 检查浮鞋内有无落物Pick up 30” conductor handling slings and shackles. 吊上下30”导管的索具和卸扣Is slope indicator properly mounted? 水平仪是否装好?Check condition of all 30” casing connectors. 检查所有30”套管接头的情况Replace O-rings as required. 按需要, 更换O性密封圈Inspect and repair diverter. 检查并修理转喷器Record all pressure tests on a chart recorder. 用试压表记录试压记录Visually inspect all sealing element. 目视检查所有密封件Check and tighten all bolts. 检查并上紧所有螺栓Bleed off surface accumulators. 地面管线排空气Check for leaks. 检查有无泄漏Lift BOP stack and replace wellhead connector AX ring. 吊起防喷器组并更换连接器AX密封圈Function test wellhead. 对井口头进行功能试验Pressure test to 500psi then bleed off test pressure. 试压到500psi, 然后放掉压力Reduce hydraulic control manifold pressure to 5200 kpa. 将液压控制管线压力减少到5200千帕Switch to alternate control pod. 把闸门开关倒到控制面板Pressure test to 5000psi. 试压5000psiPick up test mandril and place in BOP. 吊起试压防喷器芯子并装入防喷器组Safety and Firefighting 安全与消防Get a Work Permit before you can start the hot work. 办理作业许可证才能进行动火作业Welding is not allowed. 不准动焊Put on your (safety) helmet. 戴上安全帽It’s a high voltage area. 这是高压区That’s against the rule. 这是违章作业Don’t walk under the crane load. 不要在吊物下走动The repairing is under way. 正在检修Keep your hands clear! (Keep you hands off! Do not touch!) 不要乱动Wear and secure your safety belt. 戴上并系好安全带Have your breathing apparatus near you. 保持防毒面具在附近It’s a drill. 这是演习It was a BOP drill. 这是防喷演习It’s for fire fighting. 这是消防用的This rope is too small. 这根绳子太细了A warning notice should be set up. 要挂警告牌Do you have an emergency program (contingency plan)? 你们有没有应急计划? It must be ready in an emergency condition. 必须始终保持良好的应急状态Sound fire alarm. 发消防警报This is a fire drill. 这是消防演习Remove the rust and paint with anti-corrosive primer. 除锈后上防锈底漆The station bills need to be updated. 应急部署表须更新Check the expiry date for all foam extinguisher. 检查所有泡沫灭火器的过期时间Safety procedure shall be followed at all the times. 在任何时候都应遵守安全程序Don’t switch on during drilling operation. 钻井作业期间不能合闸Provide two independent means to start the emergency generator engine. 应急发电机柴油机应有两套独立的起动方法Tell the base to get (or send) a chopper here. 通知基地派飞机来Helicopters are not allowed to land here. 飞机不能降落Report the weather condition to the pilot. 向飞行员报天气Repair and Maintenance 检修Have an overall check. 进行全面检查MPI the brake linkage system. 对刹车连接系统进行磁粉探伤Demonstrate that the make-up cathead can pull 7000 lbs. 证明上扣猫头能拉到7000磅Determine the origin of the air leak and rectify this. 找出漏气的地方并处理Note that the 3000 hour inspection on TDS is due. 注意顶驱的3000小时保养时间已到Check she ave rope pocket wear with a 1 3/8”+1 1/32 template. 用1 3/8”+1/32”量规检查绳槽磨损的情况Repair the handrails on the crown. 修理天车台的栏杆Function test the anti-freefall brake on monthly basis. 每月对天车防碰装置进行功能试验Get me a spanner, please. 请递给我一把扳手Renew brake rim because of excessive wear. 更换磨损严重的刹车鼓Clearly mark safe working load (SWL) on the air winch below the rig floor. 表明钻台底下气动绞车的安全工作负荷Measure the master bushings for wear. 测量主补心磨损情况Have BOP ram opened up for internal inspection. 打开防喷器闸板进行内部检查ground cable 地线triplex pump 三缸泵We need a 48” pipe wrench. 我们需要一把48”的管钳Strike it with a sledge hammer. 用大锤打We want a triangle file. 需要一把三角锉刀Tighten up the screw. 紧一下螺丝Check it with a level. 用水平尺量一下Put some engine oil. 抹点黄油Have it greased. 给它上黄油Check all the equipment. 检查所有设备There’s something wrong with it. 有点毛病Maintain the hoisting system. 保养提升系统Adjust the brake band. 调整绞车刹带Change the oil in the rotary gear box (transmission). 更换转盘变速箱机油Replace one water pump. 倒换一台冷却泵It’s quick-discharge air valve. 这是快速放气阀This clutch needs repair. 这台离合器需修理This tong needs replacing. 这把钳要更换了Cut off 45 meters of the drilling line. 切割大绳45米Check the pump liners and pistons. 检查(泥浆)泵缸套和活塞The piston has been washed. 活塞刺坏了The supercharge pump doesn’t take in water.灌注泵不上水Regulate the relief valve. 调整安全阀This part number is wrong. 这个配件号不对The multi-pen recorder has some problem. 多笔记录仪坏了Miscellaneous 其他No smoking here. 此处严禁吸烟Everything is OK. 一切准备就绪Speed up please. 请快点The geologist must be present. 地质人员必须到场Give me a hand, please. 请帮一下忙Do you understand? 明白吗?No way! 不行Help! Help! 救命Someone is injured. Medic! 有人受伤了, 医生Call for the medic. 叫医生Get a stretcher please. 拿担架来No more than 4 persons. 不能超过4人Drinking liquor is not allowed. 不许喝酒Don’t overrun your equipment. 不要超负荷运转Be careful at work. 工作时要小心No joking here. 别开玩笑Rig up for logging. 准备电测What is the next step? 下一步怎么办?Get everything ready as soon as possible! 尽快做好一切准备21。
海洋石油钻井常用英语
海洋石油钻井常用英语第一篇：海洋石油钻井常用英语海洋石油钻井常用英语附录一：平台人员岗位名称一.承包商人员(Contractor’s Personnel)Rig Manager平台经理Equipment Supervisor设备总监Materials Supervisor材料总监Senior T oolpusher高级队长Junior T oolpusher值班队长Driller司钻Sub Sea Engineer(SSE)水下工程师Assistant Driller(AD)副司钻Derrick Man井架工Floor Man(roughneck)钻工Barge Master(captain)船长First Mate(Barge engineer)大副Control Room Operator(CRO)压载工Ballast Control Operator(BCO)压载工Chief Engineer轮机长Head of Routabout甲板班长Crane Operator吊车工Routabout甲板工Mechanic机械师Electrician电气师Repairman修理工Motorman轮机员Welder焊工Radio Operator电报员Warehouse Man(stock Keeper)材料员Medic医生Safety Supervisor安全监督Interpreter(translator)翻译Chief Steward管事Cook厨师Steward厨工Laundry Man洗衣工二.作业者及服务公司人员(Operator’s Personnel and Service Company Personnel)Drilling Superintendent钻井监督Company Man(Operator’s Representative)公司代表Geologist地质师Mud Logging Engineer(Mud logger)泥浆录井工程师Sample Catcher捞砂工Mud Engineer泥浆工程师ROV Engineer潜水工程师Cementer固井工Cement Engineer固井工程师Testing Engineer试油工程师Coring Engineer取芯工程师Wireline Logging Engineer电测工程师附录二：平台主要设备一.钻井设备(Drilling Equipment): Drawworks钻井绞车Rotary Table转盘Bushing补心Top Drive System(TDS)顶驱Swivel水龙头Crown Block天车Traveling Block游车Hook大钩Derrick井架Pipe Spinning Wrench钻杆气动扳手Ezy-Torq液压猫头Elmagco Brake涡磁刹车Pipe handling Equipment钻杆移动设备Iron roughneck铁钻工Pipe Racking System钻杆排放系统Drill String钻柱Drilling Sub钻井短节Fishing Tool打捞工具Power Tong动力大钳Air Winch(air tugger)气动绞车Crown-O-Matic(Crown Saver)防碰天车二.泥浆系统(Mud System)Mud Pump泥浆泵Shale shaker振动筛Mud Cleaner泥浆清洁器Desilter除泥器Desander除砂器Degasser除气器Centrifuge离心机Mud Agitator泥浆搅拌器Mud Mixing System泥浆混合系统Centrifugal Pump离心泵Standpipe Manifold立管管汇Rotary Hose水龙带Bulk Air System and Tank吹灰系统和灰罐三.井控设备(Well Control Equipment): Ram Type Preventor闸板防喷器Annular Type Preventor万能防喷器BOP Stack防喷器组Gate Valve闸阀Choke and Kill Manifold阻流压井管汇Remotely Operated Panel远程控制面板Choke Control Panel阻流控制面板BOP Handling Equipment防喷器搬运设备Diverter转喷器四.海事系统(Marine System)Ballast System压载系统Bilge System污水系统Vent通风口,通气口Air Supply Fan供气扇Mooring System锚泊系统Communication Equipment通讯系统Jacking System升降系统Skidding System井架滑移系统Windlass锚机Anchor锚Pendant短索Buoy浮标Lifting and Handling Equipment起吊和搬运设备五.机房(Engine Room)Diesel Engine柴油机Emergency Generator应急发电机Water Maker(desalinization unit)造淡机Air Compressor空气压缩机Boiler锅炉Air-conditioning System空调系统Sea Water Service Pump海水供给系统Piping System管汇系统Generator发电机Transformer变压器DC Motor直流马达AC Motor交流马达六.安全设备(Safety Equipment)Fire Control System消防控制系统Fire Detection System火情探测系统CO2 System二氧化碳系统Fixed Fire Extinguishing System固定消防系统Portable Extinguisher移动灭火器Fire-Fight Equipment消防设备Foam System泡沫系统Lifeboat救生艇(Inflatable)Life Raft(气涨式)救生筏Davit吊艇架Escape Routes逃生路线Breathing Apparatus呼吸器Life Buoy救生圈Gas Detection System气体探测系统Helicopter Facility直升机设施Sick-Bay(Hospital)医务室Pollution Control防污控制七.其他(Others)Cementing Unit固井装置Well Testing Equipment试油设备Mud Logging Unit泥浆录井房Wire Logging Unit电测装置ROV潜水器Meter米Foot英尺Inch英寸Supply Boat(supply vessel)供应船Standby boat值班船Day(night)Shift白(夜)班Crew Change倒班Crew船员,队员,井队Position岗位Draft(draught)吃水Air Gap空气间隙,气隙Penetration(桩腿插桩)入泥Evacuation撤离Rig(Drilling rig)钻机,钻井船附录三：平台场所Bow船首Stern船尾Forward(FWD)or fore船首的Aft船尾的Port左舷Starboard(STBD)右舷Upper Deck上部甲板Main Deck主甲板Quarters(living quarters, accommodation area)生活区Drill Floor(Rig floor)钻台Bridge(Pilot house, Steerwheel house)驾驶室Control Room控制室Helideck直升机甲板Cementing Unit Room固井泵房Air Compressor Room空气压缩机房BOP Control Room BOP控制房Radio Room报房Engine Room机房Thruster Room推进器房Warehouse(Store)材料库房Paint Room(paint locker)油漆房库Leg桩腿Jacking House升降室Column立柱Sack Storage Area散装材料储存区Mud pit泥浆池Cellar Deck圆井甲板Riser Rack Area隔水管排放区Pipe Rack Area钻杆排放区Pipe Slide滑道Ramp坡道Spud Tank桩脚箱Pontoon浮箱Moonpool月池/园井甲板Pump Room泵房Shale Shaker House振动筛房Coffee Room咖啡室Rig Office平台办公室Mess(dining)Room餐厅Recreation Room娱乐房TV Room Change Room工衣房Kitchen厨房附录四：钻具，井口工具，打捞工具Drill Pipe钻杆Drill Collar钻铤Heavy Weight Drill Pipe加重钻杆Elevator吊卡Tong大钳Make-up T ong上扣大钳Break-out Tong卸扣大钳Mud Box泥浆防喷盒Casing Stabbing Board套管扶正器Slips卡瓦Spider卡盘Mouse Hole小鼠洞(接单根用)Kelly Spinner方钻杆旋转器Kelly Cock方钻杆阀Chain Tong链钳Casing套管Tubing油管Drill String钻柱Jar(drilling jar)震击器Right Hand Thread正扣Left Hand Thread反扣Stabilizer扶正器Rabit通管器Liner尾管Conductor导管Thread Protector护丝Stand(钻杆)立柱Single(钻杆)单根Joint(钻具)根Bend弯头Sub短节Pup Joint短钻杆,短节Connector接头Bit钻头Bit Breaker钻头盒Box母扣Pin公扣Hole Opener开眼钻头Reamer扩眼钻头Overshot打捞筒Junk Basket打捞篮Junk Mill平头磨鞋Spear打捞矛Fishing Tap打捞公锥Cross Over Sub(XO Sub)转换接头Bottom Hole Assembly(BHA)下部钻具组合附录五：材料和工具Steel钢Iron铁Wood木Chemicals化学品Cement水泥Barite重晶石Potable Water淡水Drilling Water钻井水Sea Water海水Fuel柴油Helifuel飞机燃油Lubricant(Lube/Lube oil)润滑油Grease黄油Thread Dope丝扣油Ballast Water压载水Bilge Water舱底水Gasoline汽油Mud泥浆Bentonite般土Additive添加剂Caustic Soda烧碱Weight Material加重材料Thinner稀释剂Oxygen氧气Nitrogen痰气Hydrogen Sulphide二氧化硫Acetylene乙炔Compressed Air压缩空气Hydraulic Fluid液压油Spanner扳手Hammer铁锤Screw Driver螺丝刀Multimeter万用表Welding Machine焊机Bar撬杠Shackle卸扣Sling(钢丝)绳套Container集装箱附录六：常用缩写形式BHA: bottom hole assembly下部钻具组合DP: drill pipe钻杆DC: drill collar钻铤HWDP: heavy weight drill pipe加重钻杆BOP: blowout preventer防喷器TD: total depth总深TVD: true vertical depth(定向井的)垂直深度SCR: silicon controlled rectifier可控硅OD: outside diameter外径ID: inside diameter内径BBL: barrel桶LB:(拉丁语)Libra=pound(重量单位)PSI: pound per square inch 磅/英寸2 GAL: gallon加仑POOH: pull out of hole起钻RIH: run in hole下钻WOW: wait on weather等候天气WOC: wait on cement候凝JU: Jackup自升式(钻井船)SEMI: semi submersible半潜式(钻井船)RPM: revolution per minute转速/分钟LPM: liter per minute升/分钟KN: knot节(海里/小时)SWL: safe working load安全工作负荷API: American Petroleum Institute美国石油协会IADC: international association of drilling contractors国际钻井承包商协会MPI: magnetic particle inspection磁粉探伤第二篇：石油钻井英语行业英语之实用词汇现场实用词汇短语一、甲方乙方1.承包商人员(Contractor’s Personnel)Equipment Supervisor 设备总监Materials Supervisor 材料总监Senior T oolpusher 高级队长Junior T oolpusher 值班队长Driller 司钻Sub Sea Engineer(SSE)水下工程师Assistant Driller(AD)副司钻Derrick Man 井架工Floor Man(roughneck)钻工Crane Operator 吊车工Mechanic 机械师Electrician 电气师Repairman 修理工Welder 焊工Radio Operator 电报员Warehouse Man(stock Keeper)材料员Medic 医生Safety Supervisor 安全监督Interpreter(translator)翻译Chief Steward 管事Cook 厨师2、作业者及服务公司人员(Operator’s Personnel and Service Company Personnel) Drilling Superintendent 钻井监督Company Man(Operator’s Representative)公司代表Geologist 地质师Mud Logging Engineer(Mud logger)泥浆录井工程师Sample Catcher 捞砂工Mud Engineer 泥浆工程师ROV Engineer 潜水工程师Cementer 固井工Cement Engineer 固井工程师Testing Engineer 试油工程师Coring Engineer 取芯工程师Wireline Logging Engineer电测工程师二、主要设备1.钻井设备(Drilling Equipment):Drawworks 钻井绞车Rotary Table 转盘Bushing 补心Top Drive System(TDS)顶驱Swivel 水龙头Crown Block 天车Traveling Block 游车Hook 大钩Derrick 井架Pipe Spinning Wrench 钻杆气动扳手Ezy-Torq 液压猫头Elmagco Brake 涡磁刹车Pipe handling Equipment 钻杆移动设备Iron roughneck 铁钻工Pipe Racking System 钻杆排放系统Drill String 钻柱Drilling Sub 钻井短节Fishing Tool 打捞工具Power Tong 动力大钳Air Winch(air tugger)气动绞车Crown-O-Matic(Crown Saver)防碰天车2.泥浆系统(Mud System)Mud Pump 泥浆泵Shale shaker 振动筛Mud Cleaner 泥浆清洁器Desilter 除泥器Desander 除砂器Degasser 除气器Centrifuge 离心机Mud Agitator 泥浆搅拌器Mud Mixing System 泥浆混合系统Centrifugal Pump 离心泵Standpipe Manifold 立管管汇Rotary Hose 水龙带Bulk Air System and Tank 吹灰系统和灰罐3.井控设备(Well Control Equipment):Ram Type Preventor 闸板防喷器Annular Type Preventor 万能防喷器 BOP Stack 防喷器组Gate Valve 闸阀Choke and Kill Manifold 阻流压井管汇Remotely Operated Panel 远程控制面板Choke Control Panel 阻流控制面板BOP Handling Equipment 防喷器搬运设备Diverter 转喷器五.机房(Engine Room)Diesel Engine 柴油机Emergency Generator 应急发电机Water Maker(desalinization unit)造淡机Air Compressor 空气压缩机Boiler 锅炉Air-conditioning System 空调系统Piping System 管汇系统Generator 发电机Transformer 变压器DC Motor 直流马达AC Motor 交流马达4.安全设备(Safety Equipment)Fire Control System 消防控制系统Fire Detection System 火情探测系统Fixed Fire Extinguishing System 固定消防系统Portable Extinguisher 移动灭火器Fire-Fight Equipment 消防设备Foam System 泡沫系统Escape Routes 逃生路线Breathing Apparatus 呼吸器Gas Detection System 气体探测系统Helicopter Facility 直升机设施Sick-Bay(Hospital)医务室Pollution Control 防污控制5.其他(Others)Cementing Unit 固井装置Well Testing Equipment 试油设备Mud Logging Unit 泥浆录井房Wire Logging Unit 电测装置ROV 潜水器Meter 米Foot 英尺Inch 英寸Day(night)Shift 白(夜)班Crew Change 倒班 Position 岗位Penetration(桩腿插桩)入泥Evacuation 撤离Rig(Drilling rig)钻机, 钻井船Quarters(living quarters, accommodation area)生活区Drill Floor(Rig floor)钻台Bridge(Pilot house, Steerwheel house)驾驶室Control Room 控制室Helideck 直升机甲板Cementing Unit Room 固井泵房Air Compressor Room 空气压缩机房BOP Control Room BOP控制房Radio Room 报房Engine Room 机房Warehouse(Store)材料库房Paint Room(paint locker)油漆房库Mud pit 泥浆池Pipe Rack Area 钻杆排放区Pipe Slide 滑道Ramp 坡道Pump Room 泵房Shale Shaker House 振动筛房Coffee Room 咖啡室Mess(dining)Room 餐厅Recreation Room 娱乐房TV RoomChange Room 工衣房Kitchen 厨房三、钻具,井口工具,打捞工具Drill Pipe 钻杆Drill Collar 钻铤Heavy Weight Drill Pipe 加重钻杆Elevator 吊卡Tong 大钳Make-up T ong 上扣大钳Break-out Tong 卸扣大钳Mud Box 泥浆防喷盒Casing Stabbing Board 套管扶正器Slips 卡瓦Spider 卡盘Mouse Hole 小鼠洞(接单根用) Kelly Spinner 方钻杆旋转器Kelly Cock 方钻杆阀Chain Tong 链钳Casing 套管Tubing 油管Drill String 钻柱Jar(drilling jar)震击器Right Hand Thread 正扣Left Hand Thread 反扣Stabilizer 扶正器Rabit 通管器Liner 尾管Conductor 导管Thread Protector 护丝Stand(钻杆)立柱Single(钻杆)单根Joint(钻具)根Bend 弯头Sub 短节Pup Joint 短钻杆, 短节Connector 接头Bit 钻头Bit Breaker 钻头盒Box 母扣Pin 公扣Hole Opener 开眼钻头Reamer 扩眼钻头Overshot 打捞筒Junk Basket 打捞篮Junk Mill平头磨鞋Spear 打捞矛Fishing Tap 打捞公锥Cross Over Sub(XO Sub)转换接头Bottom Hole Assembly(BHA)下部钻具组合四.材料和工具Steel 钢Iron 铁Wood 木Chemicals 化学品Cement 水泥Barite 重晶石Potable Water 淡水 Fuel 柴油Lubricant(Lube/Lube oil)润滑油Grease 黄油Ballast Water 压载水 Gasoline 汽油Mud 泥浆Additive 添加剂Caustic Soda 烧碱Weight Material 加重材料Oxygen 氧气Nitrogen 痰气Hydrogen Sulphide 二氧化硫Acetylene 乙炔Compressed Air 压缩空气Hydraulic Fluid 液压油Spanner 扳手Hammer 铁锤Screw Driver 螺丝刀Multimeter 万用表Welding Machine 焊机Bar 撬杠Shackle 卸扣Sling(钢丝)绳套第三篇：海洋石油工程钻井工艺工程石油工程08级6班文果学号：0801010631海洋石油工程钻井工艺工程海洋钻井前先将钻井机械装在定位于海中的平台，钻井工艺基本上与陆地钻井相同。
石油专业英语(钻井)
石油专业英语（钻井）2008-08-02 21:02Drilling 钻井Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业. Prepared bell nipple. 准备”喇叭口”短节.Make up 2 joints of drill pipe. 接两根钻杆.Break out this connection. 卸开该接头.Run hole opener to sea bed. 下扩眼器到海底Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆.Make up bottom hole assembly. 组合下部钻具Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.Number stands on trip out and trip in. 起下钻时给立柱编号.Pick up BHA and run to seafloor. 将下部钻具下到海底.Pick up stands. 接立柱（一个立柱就是三根钻杆接在一起）Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱Drop TOTCO. 投(陶特)测斜仪Fish TOTCO with overshot. 用打捞筒捞起测斜仪Resume drilling to T.D. 继续钻进到总深Circulate 15 minutes.循环15分钟Run in hole. 下钻Put out of hole. 起钻Make an inventory of all ring gaskets. 开一个所有垫圈的清单Use spinning tong. 使用气动扳手Operate the air winch. 操作气动绞车Lay down 57 joints of 5”drill pipe. 甩57根钻杆Pick up drill stem test tool. 提起钻杆测试工具Circulate mud for 2 hours. 循环泥浆2小时Move string during circulation. 在循环时注意活动钻具Circulate hole clean. 循环清洗井眼Circulate bottoms up. 循环泥浆几周Fill up every 5 stands. 每5柱灌泥浆一次Check mud weight every 15 minutes.每15分钟检查泥浆比重Reverse out excess cement. 反循环替出多余的泥浆Change/replace old mud by new mud.用新的泥浆替换出旧的泥浆Stop drilling. 停止钻进Drilling ahead. 钻进Pull out of hole bit. 起出钻头Change bit. 换钻头Run the wear bushing. 下抗磨补心The bit thread type is regular pin. 钻头丝扣是正规公扣What’s the make-up torque? 上扣扭矩要多大?Run in 9”collars. 下9”钻铤The cathead can’t give enoughtorque. 猫头力量不够Connect crossover sub. 接上配合接头The tong angle is too small. 大钳的角度太小了地质年代术语英汉对照2008-08-0221:04stratum 地层stratigraphic correlation 地层对比horizon 层位key bed 标志层barren bed 哑层lacuna 缺失hiatus 间断continuity 连续discontinuity 不连续conformity 整合unconformity 不整合angular unconformity 角度不整合para-unconformity 平行不整合geochronologic unit 地质年代单位eon 宙era 代period 纪epoch 世stage 期chron 时chronostratigraphic unit 年代地层单位eonothem 宇erathem 界system 系series 统stage 阶chronozone 时带biostratigraphic unit 生物地层单位biostratigraphic zone 生物地层带lithostratigraphic unit 岩石地层单位group 群formation 组member 段bed 层geochronologic scale 地质年代表Phaneozoic Eon(Eonothem)显生宙（宇）Cainozoic Era(Erathem) 新生代（界）Cenozoic Era(Erathem) 新生代（界）Quaternary Period(System) 第四纪（系）Holocene Epoch(Series) 全新世（统）Pleistocene Epoch(Series) 更新世（统）Tertiary Period(System) 第三纪（系）Neogene Period(System) 新第三纪（系）Pliocene Epoch(Series) 上新世（统）Miocene Epoch(Series) 中新世（统）Paleogene Period(System) 老第三纪（系）Oligocene Epoch(Series) 渐新世（统）Eocene Epoch(Series) 始新世（统）Paleocene Epoch(Series) 古新世（统）Mesozoic Era(Erathem) 中生代（界）Cretaceous Period(System) 白垩纪（系）Jurassic Period(System) 侏罗纪（系）triassic Period(System) 三叠纪（系）Palaeozoic Era(Erathem) 古生代（界）Permian Period(System) 二叠纪（系）Carboniferous Period(System) 石炭纪（系）Devonian Period(System) 泥盆纪（系）Silurian Period(System) 志留纪（系）Ordovician Period(System) 奥陶纪（系）Cambrian Period(System) 寒武纪（系）Cryptozoic Eon(Eonothem) 隐生宙（宇）Proterozoic Eon(Eonothem) 元古宙（宇）Neoproterozoic Era(Erathem) 新元古代（界）Sinian Period(System 震旦纪（系）Mesoproterozoic Era(Erathem) 中元古代（界）Palaeoproterozoic Era(Erathem) 古元古代（界）Archaean Eon(Eonothem) 太古宙（宇）Precambrian 前寒武纪石油钻井词汇Part One SLICK-LINE（钢丝作业）A. TOOLS rope socket 绳帽stem 加重杆roll stem 滚轮加重杆Tungsten stem 钨加重杆Lead stem 铅加重杆link jar 机械震击器tubular jar 管状震击器hydraulic jar 液压震击器spring jar 弹簧震击器knuckle joint 万向节swivel joint 旋转节wellhead adapter 井口变扣短节X-Over 变扣gauge cutter 通井规selective downshift tool 选择性滑套开关工具shiftting tool 移位工具blind box 盲锤L.I.B(lead impression block) 铅印swaging tool 胀管器spear 打捞矛prong grab 内捞矛center spear 外捞矛catcher 捕捉器wirefinder 钢丝探测器Go devil-F.B 平底撞棍Go devil-C.B 刀杆撞棍retriever 钢丝打捞器overshot 卡瓦打捞筒magnetic fishing tool 磁力打捞工具sidewall cutter 刮管刀alligator grab 鳄鱼爪sand bailer 捞沙筒pipe wrench 管钳tong chain 链钳spanner 扳手wireline clamp 钢丝夹hay pulley 地滑轮dump bailer 倾倒筒saw 锯子saw blade 锯条punch 冲子file 锉刀flat file 板锉,扁锉hammer 榔头pliers,vice 老虎钳wire cutter 断线钳forfex 剪刀tongs 大钳,钳子,管钳flat bit tongs 扁嘴钳screwdriver 改锥，螺丝刀wire stripper 剥皮钳,掳线钳wire-stripper pliers 剥线钳B. EQUIPMENTstuffing box 防喷盒lubricator upper section 上防喷管lubricator middle section 中防喷管lubricator lower section 下防喷管blowout preventer(BOP) 防喷器wellhead adapter 井口变扣短节Lincoln pump 林肯泵hand pump assy.for stuffing box 手压泵Fire extinguisher 灭火器hand tool box 手工具箱injector 注油器lifting cap BOP吊帽trolly 防喷管支撑架parasol 阳伞work vice 台钳chain block 链葫芦tie down chain 系紧链fixed pulley 定滑轮wobble pump 手摇泵wire line clamp 钢丝绳夹wire rope sling 绳套,钢丝吊绳winch 绞车winch barrel(drum) 绞车滚筒winch brake 绞车刹车winch drive shaft universal joint 绞车主动轴万向节winch drum shaft 绞车滚动轴winch line 吊装用绳套winch control panel 绞车控制面板winch truck 吊车C. OPERATIONSRTTS Operation for Shoot andPull RTTS完井服务RTTS Operation for CementSqueezing RTTS固井服务（挤水泥）Pulling Y Block 捞Y堵塞器Open SSD(Slide Side Door) 开生产滑套Close SSD(Slide Side Door) 关生产滑套Open Circulating SSD(Slide SideDoor) 开循环滑套Close Circulating SSD(Slide SideDoor) 关循环滑套Running Gauge Cutter 通井Clean up 地面完井放喷Open Drain Valve 砸泻油阀Pulling Test Plug 捞测试阀Running Jet Pump 投射流泵Pulling Jet Pump 捞射流泵Running Flow Regulator 投配水器Pulling Flow Regulator 捞配水器Fishing Drop Bar 捞点火棒Measuring Static Pressure 测静压Measuring Flowing Pressure 测流压Measuring BHPBU(Bottom Hole Pressure Build Up) 测压力恢复Measuring BHP(Bottom Hole Pressure) Testing with Jet Pump 带泵测压（射流泵）Multi-Rate BHP(Bottom Hole Pressure) Testing 系统试井Slick-line Operation for Completion 钢丝配合完井服务Slick-line Operation for acidizing 配合酸化钢丝作业Running Plug 投堵塞器Pulling Plug 捞堵塞器Run Impression Block 下铅印Running Prong 投平衡杆Sand Level detection 探沙面Run Sand Bailer 下捞砂桶Open SSSV(Sub Surface Safety Valve) by Force 强行打开井下安全阀Running Go Devil 剪切钢丝Fishing Slickline 打捞钢丝Running Side Pocket Plug 投偏心堵塞器Pulling Side pocket Plug 捞偏心堵塞器Running Side Pocket Check Valve 投偏心阀Pulling Side Pocket Check Valve 捞偏心阀Sand Sampling 取砂样Stable Test 稳定试井Slickline Swab 抽吸Running Hanger 投悬挂器Pulling Hanger 捞悬挂器D. SPARE PARTSgrease injection control head 注脂头grease oil 注脂油grease oil tank 注脂油桶BOP pump c/w hose 手压泵及管线pressure test hose 试压管线lubricator bleed off manifold 防喷管针阀Martin Decker W-15 oil 马丁代克油Martin Decker WT indicator c/whose 指重器及管线picking for stuffing box 盘根bearing for the sheave for stuffingbox 轴承O-ring for lubricator 防喷管O环ram assembly for BOP 防喷管闸板总成O-ring for BOP BOP O环O-ring for wellhead adapter 井口变扣O环pin 销钉counter head 计数头cable for counter 计数器软轴bearing of hay pulley 地滑轮轴承Part two Pressure gaugeaccordance 一致,和谐accuracy 精确性,正确度acquisition 获得,获得物alignment 校直,调准append 附加,添加,悬挂apply 申请,应用available 可利用的,有用的battery 电池battery housing 电池筒battery tester 电池测量器baud rate 波特率bull nose 底堵cable 电缆,电线cable head 电缆头,电缆接头calculation 计算,考虑calibration 标度,刻度,校准calibration drift 漂移calibration parameter 标定参数cartesian 笛卡儿曲线certification 证书com port 串行通讯端口command 命令,掌握,支配communicate 沟通,交流,通讯compensate 偿还,补偿configuration 构造,结构,配置,外形configure 配置,设定consist 组成,构成control panel 控制面板convert 转换,使转变cross-over between gauge 压力计间变扣crystal 水晶,晶体current 电流damage 危险,损害data acquisition 获得数据decode 解码,译解delta time 累计时间deviate 偏离diagnostic 诊断diameter 直径digital 数字的directory 目录discussion 讨论display 显示器,显示,展示downhole tools 井下工具drain 消耗,耗尽dump data 回放数据durability 耐用性element 元素,元件,成分elevated temperature 高温encoder 译码器,编码器establish 建立,安置filter 过滤,筛选firmware 固件(软件硬件相结合)fixed rate 固定采样率flash 闪光,闪现frequency 频率,周率gauge 压力计graph 图表,曲线图grease for transducer 传感器用油housing 壳,壳体incorporate 合并,混合indicate 指出,显示individual 个别的,单独的install 安装,安置instrument 工具,器械,器具interface box 接口箱interface box 接口箱internal diagnostics 内部诊断lapse 失误,下降,过失linear plot 线性平面图log 日志maintenance 维护,保持manual 手册,指南manufacture 制造,加工merge 合并,并入,结合memory 存储器,内存module 模块observe 观察,观测offer 提供,企图parallel communication 并行通信period 周期,时期plug 堵,塞,插上,插栓port 端口,港口potential 潜在的,可能的presentation 陈述,表达presentation software 操作软件printer 打印机prior 优先的,在前的procedure 步骤,手续program 程序,节目prune 剪除,修剪,删除quality 质量,品质,性质quartz 石英range 范围,射程real time 实际时间record mode 记录模式reduce 减小,缩小,简化remote control 遥控,遥控操作remove 移动,开除,移交require 请求,要求resolution 分辨率response 回答,响应scale 刻度,天平,比例尺select 选择,挑选setup 机构,安装,装备,组织silicone oil 硅油sleep mode 休眠模式spanner for gauge 压力计专用扳手SRO(surface read-out) 地面直读surpass 超过,胜过talk mode 对话模式terminal 终点终端thread grease 丝扣油transducer 传感器,变频器,交换器transient 短暂的,瞬时的transmit 传输,传送,发射信号transport 传送器,运输机transportation box 压力计箱troubleshooting 发现并修理故障truncate 截取,修剪update 更新,校正,修正upload 上载variable rate 可变采样率various 不同的,多样的version 版本,译本volt 伏特voltage 电压wand 棒,棍,杖zoom 放大,缩放Part three PVT取样 air chamber plug extractor 空气室拉出手柄air chamber plug retaining ringextractor 梭管套旋出手柄air chamber tube assy 导流管air hose assy. 扫空管allen key 内六角autoclave vacuum nipple 抽真空头B/bench hose assy. 样瓶转样管back-up ring 背环compression spring 压缩弹簧filler funnel 漏斗flow regulator body 节流器flow regulator end cap 端帽flow regulator extractor 节流器拉出手柄fuse/110V 保险丝/110Vglycol 甘醇heating jacket for cylinder 样瓶加温器heating jacket for sampler 取样器加温器holder 装配手柄internal circlip 内簧卡internal circlip for cylinder 取样瓶卡环lock grubscrew 锁紧螺丝needle valve 针阀needle valve assy.extractor 针阀手柄needle valve body 针阀组件needle valve BUR former 针阀背环工具off ball 钢球off diskspring 弹簧片piston assy. 活塞总成piston removal 活塞移位工具piston ring 活塞环piston rod 活塞杆piston valve stem 梭阀杆pols-lock pin 锁定销钉pols-lock spring 锁定销钉弹簧posi lock pin depressing tool 锁定按压工具prime hand pump 注油器prime hand pump adaptor 注油器适配器prime port adaptor assy. 加压口适配器prime port nipple plug 加压口堵头prime port spanner 加压阀扳手prime pump assy. 手压泵适配器prime pump hose assy. 手压泵输出管push rod 推杆relief valve stem 调压阀杆retaining ring 制动环reversible circlip pliers 卡簧手钳safety solvent 清洗液sample analysis 试样分析,样品分析sample analyzer 试样分析器sample bailer 采样筒sample blob 井底取样器sample bomb 高压取样瓶,样品存储器sample bottle 取样瓶,采样瓶sample bottle valve adaptor 样瓶接头sample chamber 样品室sample cock 取样旋塞,取样拷克sample collection 取样,样品收集sample collection procedure 取样点,采样点sample collector 取样程序sample connection 试样收集器,采样员sample container 取样接头sample contamination 样瓶,样筒,样品容器sample cup 样品污染sample cylinder 样品杯sample cylinder tag 样瓶,样筒sample date 样瓶标签sample depth 取样日期sample frequency 采样深度sample hose 采样信号sample identification 取样井,采样井sample integrity 采样频率sample interval 样品管,采样胶皮管sample period 样品鉴定sample point 样品的真实性sample signal 取样间隔,取样速度sample well 取样周期sampler hose assy. 取样器软管总成setting screw 制动螺丝setting fork 导流叉管setting tool 空气定位销手柄setting tool 梭杆推进套shuttle mechanism assy. 触发机构tee ring seals T型密封环test gauge 压力表tool body clamp 取样器夹具tool dressing aids 更换'O'环工具torque wrench 扭矩扳手torque wrench adaptor 扭矩扳手接头torque wrench adaptor 扭矩扳手接头transfer bench assy. 转样器总成transfer lock sleeve 转样护帽transfer port adaptor 转样适配器transfer port plug 转样口堵头trigger mech. assy. 触发机构总成trigger spring 触发弹簧vacuum hand pump 真空泵vibra gauge 压力表Part four OthersAa directional engineer 定向井工程师a drilling engineer 钻井工程师a drilling supervisor 钻井监督a senior mud engineer 高级泥浆工程师a toolpusher 队长，技师abandoned drill 弃船演习accelevator 促凝剂acidity 酸性adapter 接头additive 添加剂/处理剂ahead water 先行水air chamber 空气包air hoist 气动绞车alarm 警报alkalinity 碱性泥浆比重amplitude log 声幅测井anchor 锚angle 角钢annular return velocity 泥浆返回流速annular space 环形空间annular velocity 环空流速apparent viscosity 视黏度asbestos 石棉assistant tug boat 护航船assistant driller 副钻aviation fuel 航空油Bback off 倒扣back pressure 回压back pressure valve 回压阀ball 球ball up 泥包barge engineer 平台工程师barite 重晶石bearing 轴承bearing angle 方位bed 床behind water 尾水bit 钻头bit bearing 钻头轴承bit breaker 钻头装卸器bit cost 钻头成本bit diameter 钻头直径bit gauge 钻头规bit life 钻头寿命bit nozzle 钻头水眼bit position 钻头位置bit sub 钻头接头bit time 钻头纯钻时间bit tooth 钻头牙齿bit torque 钻头扭矩bit type 钻头型号bit wear 钻头磨损blasting cap 雷管blow out 井喷blow out preventer 防喷器boiler 锅炉bolt 螺栓bolt,nut 螺丝,螺母bore hole 裸眼bore hole well 井壁boring 钻孔bottom hole 井底bottom fill 沉砂bottom hole pressure 井底压力bottom hole pressure 井底压力bottoms up 携带岩屑box 母扣brake 刹车break out 卸扣breech lock 泡栓build up 压力恢复bulk density 堆积密度;松装密度bulk tank 灰罐bumper sub 缓冲器buoyancy coefficient 浮力系数bushing 补芯butane 丁烷Ccable 电缆calcium remover 除钙剂calculating free piont 计算卡点深度calibration 刻度casing 套管,螺纹联接的兀接箍casing head 套管头casing spool 套管四通casing burst pressure 套管破裂压力casing elevator 套管吊卡casing monkey board 套管平台casing pressure 套压casing program 套管程序casing scraper 套管刮管器casing shoe 套管鞋casing sub 套管接头casing tong 套管大钳cathead 猫头cave in 坍塌cement 水泥cement basket 水泥伞cement bond log 固井质量检验cement flush 水泥冲洗cement slurry 水泥浆cement slurry for lead 先行水泥浆cementing 固井cementing line 固井管线cementing pump 固井泵center latch elevator 中开门吊卡centralizer 套管扶正器centrifugal pump 离心泵chain block 倒链change bit 换钻头chart 卡片check valve 单流阀chemical tank 化学药剂缸chemical treatment 化学处理chemicals 化学剂choke 油嘴choke line 阻流管汇choke manifold 试油树christmas tree 采油树circulating pressure 循环压力circulation 循环circulation rate 循环速度clamp 卡子clay contamination 粘土侵clock 时钟clog house 值班房cock 水龙头coefficient of friction 摩擦系数colloid 胶体completion 完井computer 计算机conductor 隔水导管cone 牙轮cone bit 牙轮钻头connector 联结器contamination of mud 泥浆污染contract 合同contractor 承包商control room 控制室conventional mud 普通泥浆cook 炊事员core 岩心core barrel 取芯筒core bit 取芯钻头core catcher 岩心爪core gun 取芯器core handling tools 取芯工具core recovery 取芯收获率coring 取芯coupling 联接扣cover 外壳crane operator 吊车司机critical velocity 临界速度cross 十字接头cross over,x-over(XO) 大小头，短节，变扣接头，旁通管crossover sub 配合接头crown block 天车cut off workline 割大绳cylinder 缸Ddaily production 日产量deadline 死绳deadline anchor 死绳固定器deck 甲板declination 偏差/方位角degas ser 除气器dehydration 失水densimeter 密度计depth 井深derrick 井架derrick man 架工desander 除砂器desilter 沉淀池, 滤水池detonator 炸药deviation survey 井斜测量diamond bit 金刚石钻头die collar 打捞卡瓦diesel oil 柴油different pressure sticking 压差卡钻directional well 定向井discharge of pump 泵排量dispersing agent 分散剂displace 替diver 潜水员doctor 医生drag 遇阻draw works 绞车drier(dring oven) 干燥计drift angle 倾角drift mandrel 通径规drifting 通径drill pipe 钻杆drill spool 钻井四通drill stem 钻柱drill strings 钻杆拄drill water 钻井水drill collar 钻铤drill floor 钻台drill floor 钻台driller 司钻drilling 钻进drilling technician 钻井技术员drilling assembly 钻具组合drilling break 进尺突然加快drilling cost 钻井成本drilling crew 钻井队员drilling engineer 钻井工程师drilling equipment 钻井装置,钻机drilling line 大绳drilling log 钻井记录drilling ration 钻速drilling recorder 钻井记录仪drilling rig 钻井船drilling troubles 井下事故drum shaft 滚筒轴DST(drill stem test) 延长DST测试dump valve 放泄阀duplex slush pump 双缸泥浆泵DV collar 分级注水泥短接DV port DV孔Eelbow 弯接头electric logging 电测electric submerged pump(ESP) 电潜泵electrician 电工elevator 吊卡elevator link 吊环emulsifier 乳化剂engine room 机舱erecting equipment 安装设备erecting tools 安装工具erode out 刺坏error 误差ethane 乙烷exploration 勘探extended well testing 延长测试external upset 外加厚Ffalse threading 造扣field maintenance 现场维护，现场保养fill line 灌泥浆管线filling up mud 灌泥浆filter cake 泥饼filter paper 滤纸filtration educing agent 降失水剂finger board 指梁fire drill 消防演习fishing 打捞fishing bumper sub 打捞缓冲器fishing jars 打捞震击器fishing job 打捞作业fishing neck 打捞颈fishing tools 打捞工具fishing up 打捞出落鱼flash welded tool joint 闪光焊接接头flashlight 手电float collar 浮箍float shoe 浮鞋floor man 钻工flow 放喷flow line 泥浆出口管线flow rate 流量flow line 出油管flow rate 流速flowing bean(nipple) 油嘴flowing pressure gradient 流压梯度fluid loss 失水量fluorescence 荧光反应formation 地层formation conductivities 地层电导率formation damage 破坏地层fracturing 压裂free pipe 未卡部分钻柱free point 自由点free standing mast 无绷绳轻便井架fresh water 淡水full hole(FH) 贯眼扣function 函数funnel viscometer 漏斗黏度计Ggamma ray 射线gamma ray log 自然测井gas reservoir 气层gas analysis 气体分析gas chromatography 气体色谱仪gas cut 气侵gas in mud 泥浆中气量gas oil ratio 油气比gas out 气侵gas showing 气体显示gasoline 汽油gauge 量规gear 牙轮gel 凝胶gel cement 胶质水泥gel mud 胶质泥浆gel strength 切力generator 发动机geothermal gradient 地温梯度goose neck 鹅颈管grade 级/等级grease 黄油guide shoe 引鞋gun perforation 射孔完井gypsum mud 石膏泥浆Hhammer 锤子hard ware 硬件heavy mud 重泥浆/加重泥浆heavy viscosity mud 高粘泥浆heavy weight drill pipe 加重钻杆heavy bodied 很稠的，粘滞的helicopter 直升飞机helicopter port 飞机平台helmet 安全帽hole opener 扩眼器hole size 井眼尺寸hole straightening 井眼校正/纠斜hook 大钩hook load 大钩负荷hook load off bottom 钻柱离底时大钩负荷hook position 大钩位置hopper 漏斗hose 软管/水龙带hull 船身hydraulic pressure 静水压力hydraulic oil 液压油hydrostatic pressure 静水压力IIF(internal flush) 内平扣indented bolt 齿纹螺栓indented chisel 齿状钻头，牙轮钻头indirect flushing 反循环洗井，反向冲洗induction electrical survey 感应电测井inertia brake 惯性刹车initial gel strength 出切inner barrel 内岩心筒inner string cementing 内管注水泥input 输入insert bit 镶齿钻头inside bop drill 安装回压凡尔演习intake profile 吸水剖面internal upset 内加厚internal-external upset 内外加厚interpreter 翻译invaded zone 侵入带invasion diameter 侵入直径inverse circulation 反洗井inverse well-flushing 反洗井isobutane 异丁烷isopentane 异戊烷Jjack knife mast 折叠式轻便井架jack up type drilling unit 自升式钻井船jars 震击器joint 单根junk basket 打捞蓝Kkelly 方钻杆kelly bushing 方钻杆补芯kelly cock 方钻杆考可kelly down 方入kelly down depth 方入深度kelly drive 方钻杆滚子补芯kelly spinner 方钻杆旋扣器kelly up 方余key seat 键槽key seating sticking 键槽卡钻kick 井涌kick control 控制井涌kill line 压井管汇killing a well 压井Llaminar flow 层流latching elevator 扣吊卡lay down 甩lay time 迟到时间leak 漏life raft 救生筏lifeboat 救生艇lift jacket 救生衣lifting sub 提升短接light weight mud 轻泥浆lignite 铁络盐lignite mud 铁络盐泥浆lime 石灰lime mud 石灰泥浆limit switch 相限开关line 管线line cleaning 管线清洗line test 管线试压liner 缸套,尾管liner hanger 尾管挂living quarters 居住区loading 装船logging cable 测井电缆logging program 测井程序logging tool 测井工具loosen 放松lost circulation 井漏lost circulation materials 堵漏剂lubricating oil 润滑油lubricator(assembly,system) 防喷管（装置，系统）Mmachine oil 机油main tug boat 主拖轮make up 上扣make up torque 上扣扭矩mast 钻机master bushing 转盘大补芯master valve 总闸门material man 材料员mean sea level 平均海平面mechanic 机械工mechanist 机械师methane 甲烷mica 云母milled teeth bit 铣齿钻头milling tool 铣具/磨鞋miring water 溶解水mixing pump 混合泵monkey board 二层台morning tour 白班motormen 机工mouse hole 鼠洞mud 泥浆mud agitator 泥浆搅拌器mud balance 泥浆密度计mud column 泥浆柱mud conditioning 泥浆处理/配泥浆mud conductivity 泥浆导电率mud density 泥浆密度mud ditch 泥浆槽mud flow meter 泥浆流量计mud gun 泥浆枪mud line 泥浆管线mud logging 泥浆录井mud pump 泥浆泵mud resistivity 泥浆电阻率mud retort 泥浆蒸馏水mud return line 泥浆返出管线mud tank 泥浆池mud temperature 泥浆温度mud testing 泥浆测试mud volume 泥浆量mud weight indicator 泥浆比重计mud tank 泥浆罐multiple completion 多层完井MW(mud weight) 泥浆重量,泥浆密度Nnail 钉子natural flow 自喷NDBOPS(nipple down blowout preventers) 卸下防喷器组NDT(nipple down tree) 拆卸井口装置，拆卸采油树near bit stabilizer 金钻头扶正器neutron 中子射线nipple down 卸下，拆卸nipple seating 座落接头no return 未返回水泥浆normal circulation 正循环normal butane 正丁烷normal pentane 正戊烷nozzle size 水眼尺寸nut 螺母Ooff bottom 不接触井底office 办公室oil base mud 油基泥浆oil reservoir 油层on bottom 接触井底open 打开open hole 裸眼opening 扩眼o-ring O环outer barrel 外岩心筒oven 烘箱over pulling 遇卡overshot 打捞筒Ppacker 封隔器packing 密封圈paint 油漆panel 面板paraffin plugging 蜡堵paraffin valve 清蜡闸门paraffin-treatment 清蜡处理paraffin-troubles 结蜡井parts 零件pentane 戊烷PH control additive PH控制剂phenolphthalein 酚酞pile hammer 打桩机pin 销子,公扣pincers 钳子pipe wrench 管子扳手piston 活塞piston rod 活塞杆pit drill 防喷演习pit level 泥浆液面pit level 泥浆池液面pit volume increase 泥浆增加量plastic viscosity 塑性黏度plug 水泥塞plug container 水泥头plug flow 塞流plugging back cementing 回堵注水泥pollution 污染polymer 聚合物portland cement 硅酸盐水泥potassium chlorate 氯化钾power slip 动力卡瓦power source 电源power swivel 动力水龙头power tong 动力大钳power law model 幂律模型pressure decline 压力降pressure equilibrium 压力平衡pressure gage 压力表pressure gradient 压力梯度pressure gradient 压力梯度pressure loss 压力损失pressure loss in pipe 管内压力损失pressure of mud column 泥浆柱压力pressure loss in annular 环空压力损失pressurized air 压缩空气preventer of double ram type 双闸板式防喷器production 生产propane 丙烷pry bar 撬杠，杠杆pull out of the hole 起钻pulley 滑轮pulley 滑轮pulling slip 起卡瓦pumice 浮石pump count 累计泵冲数pump efficiency 泵效pump pressure 泵压pump speed 泵速pump stroke counter 泥浆泵冲数pup joint 短接put into gear 挂挡put on break 刹车，制动PWV(production wing valve) 生产翼阀Qquick coupling 快速接头，快接管箍Rradio operator 电报员radioactivity log 放射性测井rag line 大棕绳rain density 颗粒密度rat hole 鼠洞rate of penetration 转速reamer 释放，丢手reaming 辊轴扶正器recorder 划眼red lead 记录仪reducer 丝扣油，铅油，管件润滑油regular 大小头release 正规扣relief valve 泄压阀,泄流阀reserve pit 储存池reservoir pressure 油层压力retarder 缓凝剂return 返回水泥浆return mud 反出泥浆returning fluid 井口反出液reverse circulation 反循环reverse circulation 反循环revolution 运转revolution 转数revolutions per minute 每分钟转数Reynolds number 雷诺数rig down 拆卸钻机rig up 安装钻机rig in 安装,连接rig out 拆卸ring gasket 钢圈/垫圈riser 隔水导管rope damp 绳头,绳卡rotary hose 泥浆水龙带rotary slip 转盘卡瓦rotary speed 转盘转数rotary table 转盘rotation bases 倒班roughneck 钻工roustabout 水手run casing 下套管run in the hole 下钻run length 进尺run bridge plug 下桥塞run gauge cutter 通井running tool 下入工具running in test 试车running repair 日常修理,现场维修RWTO(returned well to production) 井恢复生产Ssafety belt 安全带safety clamp 安全卡子safety joint 安全接头safety valve 安全阀sampling depth 取样井深sampling interval 取样间隔sand bridge 砂桥sand trouble 砂堵sandline 捞砂绳saturated salt-water mud 饱和盐水泥浆screw 螺钉seal 密封/封堵seating nipple 座落接头sea-water mud 海水泥浆sensor 传感器separater 分离器set back 立根盒setting slip 放卡瓦shaft 轴shale shaker 振动筛shallow gas 试气层shear rate 剪切速度shear pin 剪切销钉sheave 滑轮shock sub 减振器shoe guide 引鞋short trip 短起下钻shut in 关井shut in casing pressure 关井套管压力shut in drill pipe pressure 关井钻杆压力shut in pressure 关井压力shut off 关闭side wall neutron log 井壁中子测井silicon flour 硅粉silicon-controlled rectifier 可控硅整流器single joint elevator 单根吊卡single ram 单闸板slip 卡瓦slip type elevator 卡瓦式吊卡slip velocity 沉积速度slip workline 倒大绳slow pump 低泵速sludge tank 加重泥浆池slush pump 泥浆泵socket 插座solid content 固体含量sonic log 声波测井sonic wave 声波spacer 隔离液spare parts 备件spider 卡盘spontaneous potential log 自然电位测井spool 四通spring 弹簧spud in 开钻squeeze cementing 挤水泥stabilizer 扶正器stabilizing agent 稳定剂stage cementing 分级注水泥stainless steel 不锈钢stand 立柱stand pipe 立管stand the test 试验合格,经受考验standby 待机stand-by boat 值班船starting outfit 启动设备static pressure 静压steam 蒸气sticking 卡钻/被卡stinger 导向插头,引鞋,尾管stinger sub 插入式短节stop lost circulation 堵漏storm 风暴straight well 直井眼sub 接头,短接submerged pump 潜水泵substructure 井架底座sucking line 上水管线suction tank 吸入池supercharge pump 泥浆灌注泵supervisor 监督supply boat 供应船support 支架surge pressure 冲击压力suspending weight 悬重swab pressure 抽吸压力swabbing 抽吸switch 开关TT/B/G 牙齿/轴承/外径磨损table torque meter 转盘扭矩表table height 转盘高度taper milling 锥形刮刀technician 技术人员，技师tee 三通temperature log 温度测井ten minutes gel 终切test paper 试纸thread 丝扣tie back tool 回接工具tighten 上紧TOF(top of fishing) 落鱼顶部tong 大钳tong torque meter 大钳扭矩表ton-mile 吨-英里TOOH(tool out of hole) 起出下入井中的工具tool joint 钻杆接头tool pusher 钻井技师top valve 采油树清蜡闸门,试井闸门torch burner 喷灯torque 扭矩total depth 总井深total gas 气全量total pit 泥浆池总体积tour Shift 班towing 拖航transmission 传动装置/变速器traveling block 游动滑车tri-cone bit 三牙轮钻头trip 起下钻trip tank 计量罐tripping time 起下钻时间tubing 油管tubing hanger 油管挂tubing spool 油管四通tubing head 油管头tubing pressure 油压turbo drill 涡轮钻具turbulent flow 紊流twist off 脱扣typhoon 台风Uunconnect switch 非接触式开关unfreezing 解卡unlatching elevator 开吊卡unloading 卸栽upset 加厚Vvalve master 主阀variable density log 变密度测井V－door 井架大门vent pipe 放空管ventilate 放空,吹扫ventilation 通风,通风设备vertical depth 垂直深度viscosity 黏度volume inside pipe 管内容量volume of annulus 环空容量WW.O.O(wait on orders) 等待指令wait on 等指令wait on cement 候凝wait on(stand by) 待命walkie-talkie 对讲机wall scraper 井壁刮刀WAP(well performance analysis) 井的动态分析warning board 警告牌wash over 洗井,套洗,冲刷wash tank 洗罐,分离罐washer 洗衣机wash-over fishing operation 套洗打捞作业,套洗落鱼作业water flood pump(injection) 注水泵water flush 水循环洗井water injector(injection well) 注水井water lost(WL) 泥浆失水wax containing crude 含蜡原油waxy 蜡,蜡状物,含蜡的WDBS(weight going down before sticking) 仪器遇阻前下行重量weather 气候WEG(wireline entryguide) 喇叭口weight in air 空气中重量weight in mud 泥浆中重量weight indicator 指重表weight material 加重剂weight on bit 钻压weighted mud 重泥浆/加重泥浆welder 电焊工well 井well cleaning 洗井well head 井口well head assembly 井口装置well head pressure 井口压力well shooting 地震测井well bean 井口油嘴well blowout 井喷well bore clean up 洗井,well cementation 固井,挤水泥well cementing operation 固井作业well completing data 完井资料,数据well completing fluid 完井液well completinginformation 完井资料, wellcompleting test 完井测试well completion 完井well condition 井况well control device 井控装置well control equipment 井控设备well control fluid 压井液well control information 井控资料well control manifold 井口控制管汇well control operation 压井作业well deflection 井斜well flow under balance 诱喷well killing 压井well killing job 压井作业well killing method 压井方法well performance testing 系统试井,井动态测试,井生产测试well pulling job 起油管作业well pulling service 修井起下作业well sampling 井下取样well sand up 油井砂堵well screen 油井筛管well service tank 修井液罐well service hoist 修井机well service work 修井作业well site illumination 井场照明well testing supervisor 试油,测试监督well-completion practice 完井作业wellhead cap 井口帽wellhead choke 井口油嘴wellhead control valve 井口总阀门wellhead tap 井口短节wetting agent 润滑剂WHP(wellhead platform) 井口平台wiper trip 通井wire 钢丝wire line(WL) 电缆work accident 操作事故work assignment 工作安排work string reciprocation 工。
石油专业英语(钻井)课件
石油专业英语（钻井）2008-08-02 21:02Drilling 钻井Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业. Prepared bell nipple. 准备”喇叭口”短节.Make up 2 joints of drill pipe. 接两根钻杆.Break out this connection. 卸开该接头.Run hole opener to sea bed. 下扩眼器到海底Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆.Make up bottom hole assembly. 组合下部钻具Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.Number stands on trip out and trip in. 起下钻时给立柱编号.Pick up BHA and run to seafloor. 将下部钻具下到海底.Pick up stands. 接立柱（一个立柱就是三根钻杆接在一起）Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱Drop TOTCO. 投(陶特)测斜仪Fish TOTCO with overshot. 用打捞筒捞起测斜仪Resume drilling to T.D. 继续钻进到总深Circulate 15 minutes.循环15分钟Run in hole. 下钻Put out of hole. 起钻Make an inventory of all ring gaskets. 开一个所有垫圈的清单Use spinning tong. 使用气动扳手Operate the air winch. 操作气动绞车Lay down 57 joints of 5”drill pipe. 甩57根钻杆Pick up drill stem test tool. 提起钻杆测试工具Circulate mud for 2 hours. 循环泥浆2小时Move string during circulation. 在循环时注意活动钻具Circulate hole clean. 循环清洗井眼Circulate bottoms up. 循环泥浆几周Fill up every 5 stands. 每5柱灌泥浆一次Check mud weight every 15 minutes.每15分钟检查泥浆比重Reverse out excess cement. 反循环替出多余的泥浆Change/replace old mud by new mud.用新的泥浆替换出旧的泥浆Stop drilling. 停止钻进Drilling ahead. 钻进Pull out of hole bit. 起出钻头Change bit. 换钻头Run the wear bushing. 下抗磨补心The bit thread type is regular pin. 钻头丝扣是正规公扣What’s the make-up torque? 上扣扭矩要多大?Run in 9”collars. 下9”钻铤The cathead can’t give enoughtorque. 猫头力量不够Connect crossover sub. 接上配合接头The tong angle is too small. 大钳的角度太小了地质年代术语英汉对照2008-08-0221:04stratum 地层stratigraphic correlation 地层对比horizon 层位key bed 标志层barren bed 哑层lacuna 缺失hiatus 间断continuity 连续discontinuity 不连续conformity 整合unconformity 不整合angular unconformity 角度不整合para-unconformity 平行不整合geochronologic unit 地质年代单位eon 宙era 代period 纪epoch 世stage 期chron 时chronostratigraphic unit 年代地层单位eonothem 宇erathem 界system 系series 统stage 阶chronozone 时带biostratigraphic unit 生物地层单位biostratigraphic zone 生物地层带lithostratigraphic unit 岩石地层单位group 群formation 组member 段bed 层geochronologic scale 地质年代表Phaneozoic Eon(Eonothem)显生宙（宇）Cainozoic Era(Erathem) 新生代（界）Cenozoic Era(Erathem) 新生代（界）Quaternary Period(System) 第四纪（系）Holocene Epoch(Series) 全新世（统）Pleistocene Epoch(Series) 更新世（统）Tertiary Period(System) 第三纪（系）Neogene Period(System) 新第三纪（系）Pliocene Epoch(Series) 上新世（统）Miocene Epoch(Series) 中新世（统）Paleogene Period(System) 老第三纪（系）Oligocene Epoch(Series) 渐新世（统）Eocene Epoch(Series) 始新世（统）Paleocene Epoch(Series) 古新世（统）Mesozoic Era(Erathem) 中生代（界）Cretaceous Period(System) 白垩纪（系）Jurassic Period(System) 侏罗纪（系）triassic Period(System) 三叠纪（系）Palaeozoic Era(Erathem) 古生代（界）Permian Period(System) 二叠纪（系）Carboniferous Period(System) 石炭纪（系）Devonian Period(System) 泥盆纪（系）Silurian Period(System) 志留纪（系）Ordovician Period(System) 奥陶纪（系）Cambrian Period(System) 寒武纪（系）Cryptozoic Eon(Eonothem) 隐生宙（宇）Proterozoic Eon(Eonothem) 元古宙（宇）Neoproterozoic Era(Erathem) 新元古代（界）Sinian Period(System 震旦纪（系）Mesoproterozoic Era(Erathem) 中元古代（界）Palaeoproterozoic Era(Erathem) 古元古代（界）Archaean Eon(Eonothem) 太古宙（宇）Precambrian 前寒武纪石油钻井词汇Part One SLICK-LINE（钢丝作业）A. TOOLS rope socket 绳帽stem 加重杆roll stem 滚轮加重杆Tungsten stem 钨加重杆Lead stem 铅加重杆link jar 机械震击器tubular jar 管状震击器hydraulic jar 液压震击器spring jar 弹簧震击器knuckle joint 万向节swivel joint 旋转节wellhead adapter 井口变扣短节X-Over 变扣gauge cutter 通井规selective downshift tool 选择性滑套开关工具shiftting tool 移位工具blind box 盲锤L.I.B(lead impression block) 铅印swaging tool 胀管器spear 打捞矛prong grab 内捞矛center spear 外捞矛catcher 捕捉器wirefinder 钢丝探测器Go devil-F.B 平底撞棍Go devil-C.B 刀杆撞棍retriever 钢丝打捞器overshot 卡瓦打捞筒magnetic fishing tool 磁力打捞工具sidewall cutter 刮管刀alligator grab 鳄鱼爪sand bailer 捞沙筒pipe wrench 管钳tong chain 链钳spanner 扳手wireline clamp 钢丝夹hay pulley 地滑轮dump bailer 倾倒筒saw 锯子saw blade 锯条punch 冲子file 锉刀flat file 板锉,扁锉hammer 榔头pliers,vice 老虎钳wire cutter 断线钳forfex 剪刀tongs 大钳,钳子,管钳flat bit tongs 扁嘴钳screwdriver 改锥，螺丝刀wire stripper 剥皮钳,掳线钳wire-stripper pliers 剥线钳B. EQUIPMENTstuffing box 防喷盒lubricator upper section 上防喷管lubricator middle section 中防喷管lubricator lower section 下防喷管blowout preventer(BOP) 防喷器wellhead adapter 井口变扣短节Lincoln pump 林肯泵hand pump assy.for stuffing box 手压泵Fire extinguisher 灭火器hand tool box 手工具箱injector 注油器lifting cap BOP吊帽trolly 防喷管支撑架parasol 阳伞work vice 台钳chain block 链葫芦tie down chain 系紧链fixed pulley 定滑轮wobble pump 手摇泵wire line clamp 钢丝绳夹wire rope sling 绳套,钢丝吊绳winch 绞车winch barrel(drum) 绞车滚筒winch brake 绞车刹车winch drive shaft universal joint 绞车主动轴万向节winch drum shaft 绞车滚动轴winch line 吊装用绳套winch control panel 绞车控制面板winch truck 吊车C. OPERATIONSRTTS Operation for Shoot andPull RTTS完井服务RTTS Operation for CementSqueezing RTTS固井服务（挤水泥）Pulling Y Block 捞Y堵塞器Open SSD(Slide Side Door) 开生产滑套Close SSD(Slide Side Door) 关生产滑套Open Circulating SSD(Slide SideDoor) 开循环滑套Close Circulating SSD(Slide SideDoor) 关循环滑套Running Gauge Cutter 通井Clean up 地面完井放喷Open Drain Valve 砸泻油阀Pulling Test Plug 捞测试阀Running Jet Pump 投射流泵Pulling Jet Pump 捞射流泵Running Flow Regulator 投配水器Pulling Flow Regulator 捞配水器Fishing Drop Bar 捞点火棒Measuring Static Pressure 测静压Measuring Flowing Pressure 测流压Measuring BHPBU(Bottom Hole Pressure Build Up) 测压力恢复Measuring BHP(Bottom Hole Pressure) Testing with Jet Pump 带泵测压（射流泵）Multi-Rate BHP(Bottom Hole Pressure) Testing 系统试井Slick-line Operation for Completion 钢丝配合完井服务Slick-line Operation for acidizing 配合酸化钢丝作业Running Plug 投堵塞器Pulling Plug 捞堵塞器Run Impression Block 下铅印Running Prong 投平衡杆Sand Level detection 探沙面Run Sand Bailer 下捞砂桶Open SSSV(Sub Surface Safety Valve) by Force 强行打开井下安全阀Running Go Devil 剪切钢丝Fishing Slickline 打捞钢丝Running Side Pocket Plug 投偏心堵塞器Pulling Side pocket Plug 捞偏心堵塞器Running Side Pocket Check Valve 投偏心阀Pulling Side Pocket Check Valve 捞偏心阀Sand Sampling 取砂样Stable Test 稳定试井Slickline Swab 抽吸Running Hanger 投悬挂器Pulling Hanger 捞悬挂器D. SPARE PARTSgrease injection control head 注脂头grease oil 注脂油grease oil tank 注脂油桶BOP pump c/w hose 手压泵及管线pressure test hose 试压管线lubricator bleed off manifold 防喷管针阀Martin Decker W-15 oil 马丁代克油Martin Decker WT indicator c/whose 指重器及管线picking for stuffing box 盘根bearing for the sheave for stuffingbox 轴承O-ring for lubricator 防喷管O环ram assembly for BOP 防喷管闸板总成O-ring for BOP BOP O环O-ring for wellhead adapter 井口变扣O环pin 销钉counter head 计数头cable for counter 计数器软轴bearing of hay pulley 地滑轮轴承Part two Pressure gaugeaccordance 一致,和谐accuracy 精确性,正确度acquisition 获得,获得物alignment 校直,调准append 附加,添加,悬挂apply 申请,应用available 可利用的,有用的battery 电池battery housing 电池筒battery tester 电池测量器baud rate 波特率bull nose 底堵cable 电缆,电线cable head 电缆头,电缆接头calculation 计算,考虑calibration 标度,刻度,校准calibration drift 漂移calibration parameter 标定参数cartesian 笛卡儿曲线certification 证书com port 串行通讯端口command 命令,掌握,支配communicate 沟通,交流,通讯compensate 偿还,补偿configuration 构造,结构,配置,外形configure 配置,设定consist 组成,构成control panel 控制面板convert 转换,使转变cross-over between gauge 压力计间变扣crystal 水晶,晶体current 电流damage 危险,损害data acquisition 获得数据decode 解码,译解delta time 累计时间deviate 偏离diagnostic 诊断diameter 直径digital 数字的directory 目录discussion 讨论display 显示器,显示,展示downhole tools 井下工具drain 消耗,耗尽dump data 回放数据durability 耐用性element 元素,元件,成分elevated temperature 高温encoder 译码器,编码器establish 建立,安置filter 过滤,筛选firmware 固件(软件硬件相结合)fixed rate 固定采样率flash 闪光,闪现frequency 频率,周率gauge 压力计graph 图表,曲线图grease for transducer 传感器用油housing 壳,壳体incorporate 合并,混合indicate 指出,显示individual 个别的,单独的install 安装,安置instrument 工具,器械,器具interface box 接口箱interface box 接口箱internal diagnostics 内部诊断lapse 失误,下降,过失linear plot 线性平面图log 日志maintenance 维护,保持manual 手册,指南manufacture 制造,加工merge 合并,并入,结合memory 存储器,内存module 模块observe 观察,观测offer 提供,企图parallel communication 并行通信period 周期,时期plug 堵,塞,插上,插栓port 端口,港口potential 潜在的,可能的presentation 陈述,表达presentation software 操作软件printer 打印机prior 优先的,在前的procedure 步骤,手续program 程序,节目prune 剪除,修剪,删除quality 质量,品质,性质quartz 石英range 范围,射程real time 实际时间record mode 记录模式reduce 减小,缩小,简化remote control 遥控,遥控操作remove 移动,开除,移交require 请求,要求resolution 分辨率response 回答,响应scale 刻度,天平,比例尺select 选择,挑选setup 机构,安装,装备,组织silicone oil 硅油sleep mode 休眠模式spanner for gauge 压力计专用扳手SRO(surface read-out) 地面直读surpass 超过,胜过talk mode 对话模式terminal 终点终端thread grease 丝扣油transducer 传感器,变频器,交换器transient 短暂的,瞬时的transmit 传输,传送,发射信号transport 传送器,运输机transportation box 压力计箱troubleshooting 发现并修理故障truncate 截取,修剪update 更新,校正,修正upload 上载variable rate 可变采样率various 不同的,多样的version 版本,译本volt 伏特voltage 电压wand 棒,棍,杖zoom 放大,缩放Part three PVT取样 air chamber plug extractor 空气室拉出手柄air chamber plug retaining ringextractor 梭管套旋出手柄air chamber tube assy 导流管air hose assy. 扫空管allen key 内六角autoclave vacuum nipple 抽真空头B/bench hose assy. 样瓶转样管back-up ring 背环compression spring 压缩弹簧filler funnel 漏斗flow regulator body 节流器flow regulator end cap 端帽flow regulator extractor 节流器拉出手柄fuse/110V 保险丝/110Vglycol 甘醇heating jacket for cylinder 样瓶加温器heating jacket for sampler 取样器加温器holder 装配手柄internal circlip 内簧卡internal circlip for cylinder 取样瓶卡环lock grubscrew 锁紧螺丝needle valve 针阀needle valve assy.extractor 针阀手柄needle valve body 针阀组件needle valve BUR former 针阀背环工具off ball 钢球off diskspring 弹簧片piston assy. 活塞总成piston removal 活塞移位工具piston ring 活塞环piston rod 活塞杆piston valve stem 梭阀杆pols-lock pin 锁定销钉pols-lock spring 锁定销钉弹簧posi lock pin depressing tool 锁定按压工具prime hand pump 注油器prime hand pump adaptor 注油器适配器prime port adaptor assy. 加压口适配器prime port nipple plug 加压口堵头prime port spanner 加压阀扳手prime pump assy. 手压泵适配器prime pump hose assy. 手压泵输出管push rod 推杆relief valve stem 调压阀杆retaining ring 制动环reversible circlip pliers 卡簧手钳safety solvent 清洗液sample analysis 试样分析,样品分析sample analyzer 试样分析器sample bailer 采样筒sample blob 井底取样器sample bomb 高压取样瓶,样品存储器sample bottle 取样瓶,采样瓶sample bottle valve adaptor 样瓶接头sample chamber 样品室sample cock 取样旋塞,取样拷克sample collection 取样,样品收集sample collection procedure 取样点,采样点sample collector 取样程序sample connection 试样收集器,采样员sample container 取样接头sample contamination 样瓶,样筒,样品容器sample cup 样品污染sample cylinder 样品杯sample cylinder tag 样瓶,样筒sample date 样瓶标签sample depth 取样日期sample frequency 采样深度sample hose 采样信号sample identification 取样井,采样井sample integrity 采样频率sample interval 样品管,采样胶皮管sample period 样品鉴定sample point 样品的真实性sample signal 取样间隔,取样速度sample well 取样周期sampler hose assy. 取样器软管总成setting screw 制动螺丝setting fork 导流叉管setting tool 空气定位销手柄setting tool 梭杆推进套shuttle mechanism assy. 触发机构tee ring seals T型密封环test gauge 压力表tool body clamp 取样器夹具tool dressing aids 更换'O'环工具torque wrench 扭矩扳手torque wrench adaptor 扭矩扳手接头torque wrench adaptor 扭矩扳手接头transfer bench assy. 转样器总成transfer lock sleeve 转样护帽transfer port adaptor 转样适配器transfer port plug 转样口堵头trigger mech. assy. 触发机构总成trigger spring 触发弹簧vacuum hand pump 真空泵vibra gauge 压力表Part four OthersAa directional engineer 定向井工程师a drilling engineer 钻井工程师a drilling supervisor 钻井监督a senior mud engineer 高级泥浆工程师a toolpusher 队长，技师abandoned drill 弃船演习accelevator 促凝剂acidity 酸性adapter 接头additive 添加剂/处理剂ahead water 先行水air chamber 空气包air hoist 气动绞车alarm 警报alkalinity 碱性泥浆比重amplitude log 声幅测井anchor 锚angle 角钢annular return velocity 泥浆返回流速annular space 环形空间annular velocity 环空流速apparent viscosity 视黏度asbestos 石棉assistant tug boat 护航船assistant driller 副钻aviation fuel 航空油Bback off 倒扣back pressure 回压back pressure valve 回压阀ball 球ball up 泥包barge engineer 平台工程师barite 重晶石bearing 轴承bearing angle 方位bed 床behind water 尾水bit 钻头bit bearing 钻头轴承bit breaker 钻头装卸器bit cost 钻头成本bit diameter 钻头直径bit gauge 钻头规bit life 钻头寿命bit nozzle 钻头水眼bit position 钻头位置bit sub 钻头接头bit time 钻头纯钻时间bit tooth 钻头牙齿bit torque 钻头扭矩bit type 钻头型号bit wear 钻头磨损blasting cap 雷管blow out 井喷blow out preventer 防喷器boiler 锅炉bolt 螺栓bolt,nut 螺丝,螺母bore hole 裸眼bore hole well 井壁boring 钻孔bottom hole 井底bottom fill 沉砂bottom hole pressure 井底压力bottom hole pressure 井底压力bottoms up 携带岩屑box 母扣brake 刹车break out 卸扣breech lock 泡栓build up 压力恢复bulk density 堆积密度;松装密度bulk tank 灰罐bumper sub 缓冲器buoyancy coefficient 浮力系数bushing 补芯butane 丁烷Ccable 电缆calcium remover 除钙剂calculating free piont 计算卡点深度calibration 刻度casing 套管,螺纹联接的兀接箍casing head 套管头casing spool 套管四通casing burst pressure 套管破裂压力casing elevator 套管吊卡casing monkey board 套管平台casing pressure 套压casing program 套管程序casing scraper 套管刮管器casing shoe 套管鞋casing sub 套管接头casing tong 套管大钳cathead 猫头cave in 坍塌cement 水泥cement basket 水泥伞cement bond log 固井质量检验cement flush 水泥冲洗cement slurry 水泥浆cement slurry for lead 先行水泥浆cementing 固井cementing line 固井管线cementing pump 固井泵center latch elevator 中开门吊卡centralizer 套管扶正器centrifugal pump 离心泵chain block 倒链change bit 换钻头chart 卡片check valve 单流阀chemical tank 化学药剂缸chemical treatment 化学处理chemicals 化学剂choke 油嘴choke line 阻流管汇choke manifold 试油树christmas tree 采油树circulating pressure 循环压力circulation 循环circulation rate 循环速度clamp 卡子clay contamination 粘土侵clock 时钟clog house 值班房cock 水龙头coefficient of friction 摩擦系数colloid 胶体completion 完井computer 计算机conductor 隔水导管cone 牙轮cone bit 牙轮钻头connector 联结器contamination of mud 泥浆污染contract 合同contractor 承包商control room 控制室conventional mud 普通泥浆cooker 炊事员core 岩心core barrel 取芯筒core bit 取芯钻头core catcher 岩心爪core gun 取芯器core handling tools 取芯工具core recovery 取芯收获率coring 取芯coupling 联接扣cover 外壳crane operator 吊车司机critical velocity 临界速度cross 十字接头cross over,x-over(XO) 大小头，短节，变扣接头，旁通管crossover sub 配合接头crown block 天车cut off workline 割大绳cylinder 缸Ddaily production 日产量deadline 死绳deadline anchor 死绳固定器deck 甲板declination 偏差/方位角degas ser 除气器dehydration 失水densimeter 密度计depth 井深derrick 井架derrick man 架工desander 除砂器desilter 沉淀池, 滤水池detonator 炸药deviation survey 井斜测量diamond bit 金刚石钻头die collar 打捞卡瓦diesel oil 柴油different pressure sticking 压差卡钻directional well 定向井discharge of pump 泵排量dispersing agent 分散剂displace 替diver 潜水员doctor 医生drag 遇阻draw works 绞车drier(dring oven) 干燥计drift angle 倾角drift mandrel 通径规drifting 通径drill pipe 钻杆drill spool 钻井四通drill stem 钻柱drill strings 钻杆拄drill water 钻井水drill collar 钻铤drill floor 钻台drill floor 钻台driller 司钻drilling 钻进drilling technician 钻井技术员drilling assembly 钻具组合drilling break 进尺突然加快drilling cost 钻井成本drilling crew 钻井队员drilling engineer 钻井工程师drilling equipment 钻井装置,钻机drilling line 大绳drilling log 钻井记录drilling ration 钻速drilling recorder 钻井记录仪drilling rig 钻井船drilling troubles 井下事故drum shaft 滚筒轴DST(drill stem test) 延长DST测试dump valve 放泄阀duplex slush pump 双缸泥浆泵DV collar 分级注水泥短接DV port DV孔Eelbow 弯接头electric logging 电测electric submerged pump(ESP) 电潜泵electrician 电工elevator 吊卡elevator link 吊环emulsifier 乳化剂engine room 机舱erecting equipment 安装设备erecting tools 安装工具erode out 刺坏error 误差ethane 乙烷exploration 勘探extended well testing 延长测试external upset 外加厚Ffalse threading 造扣field maintenance 现场维护，现场保养fill line 灌泥浆管线filling up mud 灌泥浆filter cake 泥饼filter paper 滤纸filtration educing agent 降失水剂finger board 指梁fire drill 消防演习fishing 打捞fishing bumper sub 打捞缓冲器fishing jars 打捞震击器fishing job 打捞作业fishing neck 打捞颈fishing tools 打捞工具fishing up 打捞出落鱼flash welded tool joint 闪光焊接接头flashlight 手电float collar 浮箍float shoe 浮鞋floor man 钻工flow 放喷flow line 泥浆出口管线flow rate 流量flow line 出油管flow rate 流速flowing bean(nipple) 油嘴flowing pressure gradient 流压梯度fluid loss 失水量fluorescence 荧光反应formation 地层formation conductivities 地层电导率formation damage 破坏地层fracturing 压裂free pipe 未卡部分钻柱free point 自由点free standing mast 无绷绳轻便井架fresh water 淡水full hole(FH) 贯眼扣function 函数funnel viscometer 漏斗黏度计Ggamma ray 射线gamma ray log 自然测井gas reservoir 气层gas analysis 气体分析gas chromatography 气体色谱仪gas cut 气侵gas in mud 泥浆中气量gas oil ratio 油气比gas out 气侵gas showing 气体显示gasoline 汽油gauge 量规gear 牙轮gel 凝胶gel cement 胶质水泥gel mud 胶质泥浆gel strength 切力generator 发动机geothermal gradient 地温梯度goose neck 鹅颈管grade 级/等级grease 黄油guide shoe 引鞋gun perforation 射孔完井gypsum mud 石膏泥浆Hhammer 锤子hard ware 硬件heavy mud 重泥浆/加重泥浆heavy viscosity mud 高粘泥浆heavy weight drill pipe 加重钻杆heavy bodied 很稠的，粘滞的helicopter 直升飞机helicopter port 飞机平台helmet 安全帽hole opener 扩眼器hole size 井眼尺寸hole straightening 井眼校正/纠斜hook 大钩hook load 大钩负荷hook load off bottom 钻柱离底时大钩负荷hook position 大钩位置hopper 漏斗hose 软管/水龙带hull 船身hydraulic pressure 静水压力hydraulic oil 液压油hydrostatic pressure 静水压力IIF(internal flush) 内平扣indented bolt 齿纹螺栓indented chisel 齿状钻头，牙轮钻头indirect flushing 反循环洗井，反向冲洗induction electrical survey 感应电测井inertia brake 惯性刹车initial gel strength 出切inner barrel 内岩心筒inner string cementing 内管注水泥input 输入insert bit 镶齿钻头inside bop drill 安装回压凡尔演习intake profile 吸水剖面internal upset 内加厚internal-external upset 内外加厚interpreter 翻译invaded zone 侵入带invasion diameter 侵入直径inverse circulation 反洗井inverse well-flushing 反洗井isobutane 异丁烷isopentane 异戊烷Jjack knife mast 折叠式轻便井架jack up type drilling unit 自升式钻井船jars 震击器joint 单根junk basket 打捞蓝Kkelly 方钻杆kelly bushing 方钻杆补芯kelly cock 方钻杆考可kelly down 方入kelly down depth 方入深度kelly drive 方钻杆滚子补芯kelly spinner 方钻杆旋扣器kelly up 方余key seat 键槽key seating sticking 键槽卡钻kick 井涌kick control 控制井涌kill line 压井管汇killing a well 压井Llaminar flow 层流latching elevator 扣吊卡lay down 甩lay time 迟到时间leak 漏life raft 救生筏lifeboat 救生艇lift jacket 救生衣lifting sub 提升短接light weight mud 轻泥浆lignite 铁络盐lignite mud 铁络盐泥浆lime 石灰lime mud 石灰泥浆limit switch 相限开关line 管线line cleaning 管线清洗line test 管线试压liner 缸套,尾管liner hanger 尾管挂living quarters 居住区loading 装船logging cable 测井电缆logging program 测井程序logging tool 测井工具loosen 放松lost circulation 井漏lost circulation materials 堵漏剂lubricating oil 润滑油lubricator(assembly,system) 防喷管（装置，系统）Mmachine oil 机油main tug boat 主拖轮make up 上扣make up torque 上扣扭矩mast 钻机master bushing 转盘大补芯master valve 总闸门material man 材料员mean sea level 平均海平面mechanic 机械工mechanist 机械师methane 甲烷mica 云母milled teeth bit 铣齿钻头milling tool 铣具/磨鞋miring water 溶解水mixing pump 混合泵monkey board 二层台morning tour 白班motormen 机工mouse hole 鼠洞mud 泥浆mud agitator 泥浆搅拌器mud balance 泥浆密度计mud column 泥浆柱mud conditioning 泥浆处理/配泥浆mud conductivity 泥浆导电率mud density 泥浆密度mud ditch 泥浆槽mud flow meter 泥浆流量计mud gun 泥浆枪mud line 泥浆管线mud logging 泥浆录井mud pump 泥浆泵mud resistivity 泥浆电阻率mud retort 泥浆蒸馏水mud return line 泥浆返出管线mud tank 泥浆池mud temperature 泥浆温度mud testing 泥浆测试mud volume 泥浆量mud weight indicator 泥浆比重计mud tank 泥浆罐multiple completion 多层完井MW(mud weight) 泥浆重量,泥浆密度Nnail 钉子natural flow 自喷NDBOPS(nipple down blowout preventers) 卸下防喷器组NDT(nipple down tree) 拆卸井口装置，拆卸采油树near bit stabilizer 金钻头扶正器neutron 中子射线nipple down 卸下，拆卸nipple seating 座落接头no return 未返回水泥浆normal circulation 正循环normal butane 正丁烷normal pentane 正戊烷nozzle size 水眼尺寸nut 螺母Ooff bottom 不接触井底office 办公室oil base mud 油基泥浆oil reservoir 油层on bottom 接触井底open 打开open hole 裸眼opening 扩眼o-ring O环outer barrel 外岩心筒oven 烘箱over pulling 遇卡overshot 打捞筒Ppacker 封隔器packing 密封圈paint 油漆panel 面板paraffin plugging 蜡堵paraffin valve 清蜡闸门paraffin-treatment 清蜡处理paraffin-troubles 结蜡井parts 零件pentane 戊烷PH control additive PH控制剂phenolphthalein 酚酞pile hammer 打桩机pin 销子,公扣pincers 钳子pipe wrench 管子扳手piston 活塞piston rod 活塞杆pit drill 防喷演习pit level 泥浆液面pit level 泥浆池液面pit volume increase 泥浆增加量plastic viscosity 塑性黏度plug 水泥塞plug container 水泥头plug flow 塞流plugging back cementing 回堵注水泥pollution 污染polymer 聚合物portland cement 硅酸盐水泥potassium chlorate 氯化钾power slip 动力卡瓦power source 电源power swivel 动力水龙头power tong 动力大钳power law model 幂律模型pressure decline 压力降pressure equilibrium 压力平衡pressure gage 压力表pressure gradient 压力梯度pressure gradient 压力梯度pressure loss 压力损失pressure loss in pipe 管内压力损失pressure of mud column 泥浆柱压力pressure loss in annular 环空压力损失pressurized air 压缩空气preventer of double ram type 双闸板式防喷器production 生产propane 丙烷pry bar 撬杠，杠杆pull out of the hole 起钻pulley 滑轮pulley 滑轮pulling slip 起卡瓦pumice 浮石pump count 累计泵冲数pump efficiency 泵效pump pressure 泵压pump speed 泵速pump stroke counter 泥浆泵冲数pup joint 短接put into gear 挂挡put on break 刹车，制动PWV(production wing valve) 生产翼阀Qquick coupling 快速接头，快接管箍Rradio operator 电报员radioactivity log 放射性测井rag line 大棕绳rain density 颗粒密度rat hole 鼠洞rate of penetration 转速reamer 释放，丢手reaming 辊轴扶正器recorder 划眼red lead 记录仪reducer 丝扣油，铅油，管件润滑油regular 大小头release 正规扣relief valve 泄压阀,泄流阀reserve pit 储存池reservoir pressure 油层压力retarder 缓凝剂return 返回水泥浆return mud 反出泥浆returning fluid 井口反出液reverse circulation 反循环reverse circulation 反循环revolution 运转revolution 转数revolutions per minute 每分钟转数Reynolds number 雷诺数rig down 拆卸钻机rig up 安装钻机rig in 安装,连接rig out 拆卸ring gasket 钢圈/垫圈riser 隔水导管rope damp 绳头,绳卡rotary hose 泥浆水龙带rotary slip 转盘卡瓦rotary speed 转盘转数rotary table 转盘rotation bases 倒班roughneck 钻工roustabout 水手run casing 下套管run in the hole 下钻run length 进尺run bridge plug 下桥塞run gauge cutter 通井running tool 下入工具running in test 试车running repair 日常修理,现场维修RWTO(returned well to production) 井恢复生产Ssafety belt 安全带safety clamp 安全卡子safety joint 安全接头safety valve 安全阀sampling depth 取样井深sampling interval 取样间隔sand bridge 砂桥sand trouble 砂堵sandline 捞砂绳saturated salt-water mud 饱和盐水泥浆screw 螺钉seal 密封/封堵seating nipple 座落接头sea-water mud 海水泥浆sensor 传感器separater 分离器set back 立根盒setting slip 放卡瓦shaft 轴shale shaker 振动筛shallow gas 试气层shear rate 剪切速度shear pin 剪切销钉sheave 滑轮shock sub 减振器shoe guide 引鞋short trip 短起下钻shut in 关井shut in casing pressure 关井套管压力shut in drill pipe pressure 关井钻杆压力shut in pressure 关井压力shut off 关闭side wall neutron log 井壁中子测井silicon flour 硅粉silicon-controlled rectifier 可控硅整流器single joint elevator 单根吊卡single ram 单闸板slip 卡瓦slip type elevator 卡瓦式吊卡slip velocity 沉积速度slip workline 倒大绳slow pump 低泵速sludge tank 加重泥浆池slush pump 泥浆泵socket 插座solid content 固体含量sonic log 声波测井sonic wave 声波spacer 隔离液spare parts 备件spider 卡盘spontaneous potential log 自然电位测井spool 四通spring 弹簧spud in 开钻squeeze cementing 挤水泥stabilizer 扶正器stabilizing agent 稳定剂stage cementing 分级注水泥stainless steel 不锈钢stand 立柱stand pipe 立管stand the test 试验合格,经受考验standby 待机stand-by boat 值班船starting outfit 启动设备static pressure 静压steam 蒸气sticking 卡钻/被卡stinger 导向插头,引鞋,尾管stinger sub 插入式短节stop lost circulation 堵漏storm 风暴straight well 直井眼sub 接头,短接submerged pump 潜水泵substructure 井架底座sucking line 上水管线suction tank 吸入池supercharge pump 泥浆灌注泵supervisor 监督supply boat 供应船support 支架surge pressure 冲击压力suspending weight 悬重swab pressure 抽吸压力swabbing 抽吸switch 开关TT/B/G 牙齿/轴承/外径磨损table torque meter 转盘扭矩表table height 转盘高度taper milling 锥形刮刀technician 技术人员，技师tee 三通temperature log 温度测井ten minutes gel 终切test paper 试纸thread 丝扣tie back tool 回接工具tighten 上紧TOF(top of fishing) 落鱼顶部tong 大钳tong torque meter 大钳扭矩表ton-mile 吨-英里TOOH(tool out of hole) 起出下入井中的工具tool joint 钻杆接头tool pusher 钻井技师top valve 采油树清蜡闸门,试井闸门torch burner 喷灯torque 扭矩total depth 总井深total gas 气全量total pit 泥浆池总体积tour Shift 班towing 拖航transmission 传动装置/变速器traveling block 游动滑车tri-cone bit 三牙轮钻头trip 起下钻trip tank 计量罐tripping time 起下钻时间tubing 油管tubing hanger 油管挂tubing spool 油管四通tubing head 油管头tubing pressure 油压turbo drill 涡轮钻具turbulent flow 紊流twist off 脱扣typhoon 台风Uunconnect switch 非接触式开关unfreezing 解卡unlatching elevator 开吊卡unloading 卸栽upset 加厚Vvalve master 主阀variable density log 变密度测井V－door 井架大门vent pipe 放空管ventilate 放空,吹扫ventilation 通风,通风设备vertical depth 垂直深度viscosity 黏度volume inside pipe 管内容量volume of annulus 环空容量WW.O.O(wait on orders) 等待指令wait on 等指令wait on cement 候凝wait on(stand by) 待命walkie-talkie 对讲机wall scraper 井壁刮刀WAP(well performance analysis) 井的动态分析warning board 警告牌wash over 洗井,套洗,冲刷wash tank 洗罐,分离罐washer 洗衣机wash-over fishing operation 套洗打捞作业,套洗落鱼作业water flood pump(injection) 注水泵water flush 水循环洗井water injector(injection well) 注水井water lost(WL) 泥浆失水wax containing crude 含蜡原油waxy 蜡,蜡状物,含蜡的WDBS(weight going down before sticking) 仪器遇阻前下行重量weather 气候WEG(wireline entryguide) 喇叭口weight in air 空气中重量weight in mud 泥浆中重量weight indicator 指重表weight material 加重剂weight on bit 钻压weighted mud 重泥浆/加重泥浆welder 电焊工well 井well cleaning 洗井well head 井口well head assembly 井口装置well head pressure 井口压力well shooting 地震测井well bean 井口油嘴well blowout 井喷well bore clean up 洗井,well cementation 固井,挤水泥well cementing operation 固井作业well completing data 完井资料,数据well completing fluid 完井液well completinginformation 完井资料, wellcompleting test 完井测试well completion 完井well condition 井况well control device 井控装置well control equipment 井控设备well control fluid 压井液well control information 井控资料well control manifold 井口控制管汇well control operation 压井作业well deflection 井斜well flow under balance 诱喷well killing 压井well killing job 压井作业well killing method 压井方法well performance testing 系统试井,井动态测试,井生产测试well pulling job 起油管作业well pulling service 修井起下作业well sampling 井下取样well sand up 油井砂堵well screen 油井筛管well service tank 修井液罐well service hoist 修井机well service work 修井作业well site illumination 井场照明well testing supervisor 试油,测试监督well-completion practice 完井作业wellhead cap 井口帽wellhead choke 井口油嘴wellhead control valve 井口总阀门wellhead tap 井口短节wetting agent 润滑剂WHP(wellhead platform) 井口平台wiper trip 通井wire 钢丝wire line(WL) 电缆work accident 操作事故work assignment 工作安排work string reciprocation 工。
A Handbook of English for Offshore Drilling - printed
链钳 倒链 链式吊索 麻花吊绳 纤维吊绳 金属箍 主吊环 链接环 工具箱 工作台 梯子 打磨机 砂轮 砂纸 护目镜 安全带 吊人吊带 电池 充电器 对讲机 手电筒 测量工具 卷尺 游标卡尺 生胶带 仪表 万用表 量杯 漏斗粘度计 泥浆比重计，泥浆天平 刷子 钢丝刷 垫木，模块 除锈机 锈 油壶 支撑架，底座 卡箍 手推车 滑轮 眼孔 平台
[splain] [end] ['spænə] [,kɔmbi'neiʃən] ['spænə] [ə'dʒʌstəbl]['spænə] [tɔ:k] [rentʃ] [paip] [rentʃ] ['ælən] [rentʃ] ['sɔkit] [siks] [pɔint]['sɔkit] [twelv] [pɔint] ['sɔkit] [,ju:ni'və:səl] ['sɔkit] [ə'dæptə] ['sɔkit] [iks'tenʃən] ['skru: ,draivə] ['filips]['skru: ,draivə] [flæt][tip]['skru:,draivə] ['plaiəz] ['lɔkiŋ] ['plaiəz] ['seifti]['waiə] ['twistə] ['ni:dl] [nəuz]['plaiəz] ['hæmə] [klɔ:]['hæmə] ['krəubɑ:] [sɔ:] ['hæksɔ:] [sɔ:][bleid] [ʃiə] ['nipə] [fail] ['tʃizl] [pʌntʃ] [huk][tʌɡ] [ɡri:s] [ɡʌn] [naif] [klɑ:sp] [naif] [ɡlʌv] [rəup] [kən'teinə] ['waiə] [lain] [tæɡ] [lain] [paip] [sliŋ] ['ʃækl] [tʃein]
钻井英语手册
第一部分海上钻井英语口语500句一、RIG JACKING-DOWN AND LEG-PULLING OUT 降船及拔桩1、Everything’s ready for the move? Has the unloading finished？准备工作做得怎么样？卸载做完没有？2、They are working to remove the wedges？现在正在拔桩脚楔块。
3、The derrick has been skidded to the towing position?井架已移到适航位置。
4、Drop NO.2 anchor first，and then No.3.先抛2号锚，后抛3号锚。
5、How far are going to lay out the anchor line？锚缆绳需要放多少？6、Keep five warps on the drum and lay out the rest.尽可能放，滚筒上留5圈。
7、We ’ve got through with the anchors，It ’s ready for the boat to connect now.已抛完锚，可以接拖了。
8、Have you got emergency equipments ready for the moving？拖航作业的应急器材准备完了吗？9、The variable load is over the allowable limit. We’ll have to unload the surpluscement，drilling to unload the surplus cement，drilling water and some diesel oil. 可变负荷超过允许量了，应该卸掉多余的水泥、钻井水，以及部分油。
10、Is it O.K to jack the rig down today?今天可以降船吗？11、We can’t jack down the rig as the weather is bad.天气不好，不能降船。
海上采油英语实用手册（英汉对照）-句子
海上采油英语实用手册（英汉对照）-句子2.Sentences 句子控制仪表1.The purpose of emergency shutdowe system is to protect personnel and the facility from threats 应急关断系统目的就是保护人身，设施免受威胁。
2.The emergency shutdown system consists of a number of individual process shutdowns.应急关断系统有许多单独的工艺流程关断组成.3.The emergeney shutdown is actuated by either manual controls or automatic devices sensing abnormol conditions.应急关断解即可由手动手动控制启动也可在感应到不正常状态下自动启动4.When a most hazardons situation has risen the total shutdown of the plant is performed manually.当最危险情况发生时，平台的最关断阀可自动启动5.Level 1A shutdown includes the shutdown of all wells and process facility.1A级关断将关断所有油井及工艺设施。
6.Level 1B causes a total shutdown , starting-up of emergency power and fire fighting system.1B级关断引起总关断，同时启动应急发电机救火系统。
7.When accidents happen during process operation ,the process shutdown is performed manually at the CCR.生产中产生意外事故，在CCR上即可手动关断工艺系统。
钻井英语手册
钻井英语手册第一部分海上钻井英语口语500句一、RIG JACKING-DOWN AND LEG-PULLING OUT 降船及拔桩1、Everything’s ready for the move? Has the unloading finished？准备工作做得怎么样？卸载做完没有？2、They are working to remove the wedges？现在正在拔桩脚楔块。
3、The derrick has been skidded to the towing position?井架已移到适航位置。
4、Drop NO.2 anchor first，and then No.3.先抛2号锚，后抛3号锚。
5、How far are going to lay out the anchor line？锚缆绳需要放多少？6、Keep five warps on the drum and lay out the rest.尽可能放，滚筒上留5圈。
7、We ’ve got through with the anchors，It ’s ready for the boat to connect now.已抛完锚，可以接拖了。
8、Have you got emergency equipments ready for the moving？拖航作业的应急器材准备完了吗？9、The variable load is over the allowable limit. We’ll have to unload the surpluscement，drilling to unload the surplus cement，drilling water and some diesel oil. 可变负荷超过允许量了，应该卸掉多余的水泥、钻井水，以及部分油。
10、Is it O.K to jack the rig down today?今天可以降船吗？11、We can’t jack down the rig as the weather is bad.天气不好，不能降船。
钻井常用英语手册
A Handbook of English for Offshore Oil Drilling海洋石油钻井常用英语手册附录一: 平台人员岗位名称一. 承包商人员( Contractor’s Personnel )Rig Manager 平台经理Equipment Supervisor 设备总监Materials Supervisor 材料总监Senior Toolpusher 高级队长Junior Toolpusher 值班队长Driller 司钻Sub Sea Engineer (SSE) 水下工程师Assistant Driller (AD) 副司钻Derrick Man 井架工Floor Man (roughneck) 钻工Barge Master (captain) 船长First Mate (Barge engineer) 大副Control Room Operator (CRO) 压载工Ballast Control Operator (BCO) 压载工Chief Engineer 轮机长Head of Routabout 甲板班长Crane Operator 吊车工Routabout 甲板工Mechanic 机械师Electrician 电气师Repairman 修理工Motorman 轮机员Welder 焊工Radio Operator 电报员Warehouse Man (stock Keeper) 材料员Medic 医生Safety Supervisor 安全监督Interpreter (translator) 翻译Chief Steward 管事Cook 厨师Steward 厨工Laundry Man 洗衣工二. 作业者及服务公司人员( Operator’s Personnel and Service Company Personnel) Drilling Superintendent 钻井监督Company Man (Operator’s Representative) 公司代表Geologist 地质师Mud Logging Engineer (Mud logger) 泥浆录井工程师Sample Catcher 捞砂工Mud Engineer 泥浆工程师ROV Engineer 潜水工程师Cementer 固井工Cement Engineer 固井工程师Testing Engineer 试油工程师Coring Engineer 取芯工程师Wireline Logging Engineer电测工程师附录二: 平台主要设备一. 钻井设备(Drilling Equipment): Drawworks 钻井绞车Rotary Table 转盘Bushing 补心Top Drive System (TDS) 顶驱Swivel 水龙头Crown Block 天车Traveling Block 游车Hook 大钩Derrick 井架Pipe Spinning Wrench 钻杆气动扳手Ezy-Torq 液压猫头Elmagco Brake 涡磁刹车Pipe handling Equipment 钻杆移动设备Iron roughneck 铁钻工Pipe Racking System 钻杆排放系统Drill String 钻柱Drilling Sub 钻井短节Fishing Tool 打捞工具Power Tong 动力大钳Air Winch (air tugger) 气动绞车Crown-O-Matic (Crown Saver) 防碰天车二. 泥浆系统(Mud System)Mud Pump 泥浆泵Shale shaker 振动筛Mud Cleaner 泥浆清洁器Desilter 除泥器Desander 除砂器Degasser 除气器Centrifuge 离心机Mud Agitator 泥浆搅拌器Mud Mixing System 泥浆混合系统Centrifugal Pump 离心泵Standpipe Manifold 立管管汇Rotary Hose 水龙带Bulk Air System and Tank 吹灰系统和灰罐三. 井控设备(Well Control Equipment): Ram Type Preventor 闸板防喷器Annular Type Preventor 万能防喷器BOP Stack 防喷器组Gate Valve 闸阀Choke and Kill Manifold 阻流压井管汇Remotely Operated Panel 远程控制面板Choke Control Panel 阻流控制面板BOP Handling Equipment 防喷器搬运设备Diverter 转喷器四. 海事系统(Marine System)Ballast System 压载系统Bilge System 污水系统Vent 通风口, 通气口Air Supply Fan 供气扇Mooring System 锚泊系统Communication Equipment 通讯系统Jacking System 升降系统Skidding System 井架滑移系统Windlass 锚机Anchor 锚Pendant 短索Buoy 浮标Lifting and Handling Equipment 起吊和搬运设备五. 机房(Engine Room)Diesel Engine 柴油机Emergency Generator 应急发电机Water Maker (desalinization unit) 造淡机Air Compressor 空气压缩机Boiler 锅炉Air-conditioning System 空调系统Sea Water Service Pump 海水供给系统Piping System 管汇系统Generator 发电机Transformer 变压器DC Motor 直流马达AC Motor 交流马达六. 安全设备(Safety Equipment)Fire Control System 消防控制系统Fire Detection System 火情探测系统CO2 System 二氧化碳系统Fixed Fire Extinguishing System 固定消防系统Portable Extinguisher 移动灭火器Fire-Fight Equipment 消防设备Foam System 泡沫系统Lifeboat 救生艇(Inflatable) Life Raft (气涨式)救生筏Davit 吊艇架Escape Routes 逃生路线Breathing Apparatus 呼吸器Life Buoy 救生圈Gas Detection System 气体探测系统Helicopter Facility 直升机设施Sick-Bay (Hospital) 医务室Pollution Control 防污控制七. 其他( Others)Cementing Unit 固井装置Well Testing Equipment 试油设备Mud Logging Unit 泥浆录井房Wire Logging Unit 电测装置ROV 潜水器Meter 米Foot 英尺Inch 英寸Supply Boat (supply vessel) 供应船Standby boat 值班船Day (night) Shift 白(夜)班Crew Change 倒班Crew 船员, 队员, 井队Position 岗位Draft (draught) 吃水Air Gap 空气间隙, 气隙Penetration (桩腿插桩)入泥Evacuation 撤离Rig (Drilling rig) 钻机, 钻井船附录三. 平台场所Bow 船首Stern 船尾Forward (FWD) or fore 船首的Aft 船尾的Port 左舷Starboard (STBD) 右舷Upper Deck 上部甲板Main Deck 主甲板Quarters (living quarters, accommodation area) 生活区Drill Floor (Rig floor) 钻台Bridge (Pilot house, Steerwheel house) 驾驶室Control Room 控制室Helideck 直升机甲板Cementing Unit Room 固井泵房Air Compressor Room 空气压缩机房BOP Control Room BOP控制房Radio Room 报房Engine Room 机房Thruster Room 推进器房Warehouse (Store) 材料库房Paint Room (paint locker) 油漆房库Leg 桩腿Jacking House 升降室Column 立柱Sack Storage Area 散装材料储存区Mud pit 泥浆池Cellar Deck 圆井甲板Riser Rack Area 隔水管排放区Pipe Rack Area 钻杆排放区Pipe Slide 滑道Ramp 坡道Spud Tank 桩脚箱Pontoon 浮箱Moonpool 月池/园井甲板Pump Room 泵房Shale Shaker House 振动筛房Coffee Room 咖啡室Rig Office 平台办公室Mess (dining) Room 餐厅Recreation Room 娱乐房TV RoomChange Room 工衣房Kitchen 厨房附录四. 钻具,井口工具,打捞工具Drill Pipe 钻杆Drill Collar 钻铤Heavy Weight Drill Pipe 加重钻杆Elevator 吊卡Tong 大钳Make-up Tong 上扣大钳Break-out Tong 卸扣大钳Mud Box 泥浆防喷盒Casing Stabbing Board 套管扶正器Slips 卡瓦Spider 卡盘Mouse Hole 小鼠洞(接单根用) Kelly Spinner 方钻杆旋转器Kelly Cock 方钻杆阀Chain Tong 链钳Casing 套管Tubing 油管Drill String 钻柱Jar (drilling jar) 震击器Right Hand Thread 正扣Left Hand Thread 反扣Stabilizer 扶正器Rabit 通管器Liner 尾管Conductor 导管Thread Protector 护丝Stand (钻杆) 立柱Single (钻杆) 单根Joint (钻具) 根Bend 弯头Sub 短节Pup Joint 短钻杆, 短节Connector 接头Bit 钻头Bit Breaker 钻头盒Box 母扣Pin 公扣Hole Opener 开眼钻头Reamer 扩眼钻头Overshot 打捞筒Junk Basket 打捞篮Junk Mill 平头磨鞋Spear 打捞矛Fishing Tap 打捞公锥Cross Over Sub (XO Sub) 转换接头Bottom Hole Assembly (BHA) 下部钻具组合附录五. 材料和工具Steel 钢Iron 铁Wood 木Chemicals 化学品Cement 水泥Barite 重晶石Potable Water 淡水Drilling Water 钻井水Sea Water 海水Fuel 柴油Helifuel 飞机燃油Lubricant (Lube/Lube oil) 润滑油Grease 黄油Thread Dope 丝扣油Ballast Water 压载水Bilge Water 舱底水Gasoline 汽油Mud 泥浆Bentonite 般土Additive 添加剂Caustic Soda 烧碱Weight Material 加重材料Thinner 稀释剂Oxygen 氧气Nitrogen 痰气Hydrogen Sulphide 二氧化硫Acetylene 乙炔Compressed Air 压缩空气Hydraulic Fluid 液压油Spanner 扳手Hammer 铁锤Screw Driver 螺丝刀Multimeter 万用表Welding Machine 焊机Bar 撬杠Shackle 卸扣Sling (钢丝) 绳套Container 集装箱附录六. 常用缩写形式BHA: bottom hole assembly 下部钻具组合DP: drill pipe 钻杆DC: drill collar 钻铤HWDP: heavy weight drill pipe 加重钻杆BOP: blowout preventer 防喷器TD: total depth 总深TVD: true vertical depth (定向井的)垂直深度SCR: silicon controlled rectifier 可控硅OD: outside diameter 外径ID: inside diameter 内径BBL: barrel 桶LB: (拉丁语) Libra=pound (重量单位) PSI: pound per square inch 磅/英寸2 GAL: gallon 加仑POOH: pull out of hole 起钻RIH: run in hole 下钻WOW: wait on weather 等候天气WOC: wait on cement 候凝JU: Jackup 自升式(钻井船)SEMI: semi submersible 半潜式(钻井船)RPM: revolution per minute 转速/分钟LPM: liter per minute 升/分钟KN: knot 节(海里/小时)SWL: safe working load 安全工作负荷API: American Petroleum Institute 美国石油协会IADC: international association of drilling contractors 国际钻井承包商协会MPI: magnetic particle inspection 磁粉探伤附录七:常用语Drilling 钻井Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业.Prepared bell nipple. 准备”喇叭口”短节.Make up 2 joints of drill pipe. 接两根钻杆.Break out this connection. 卸开该接头.Run hole opener to sea bed. 下扩眼器到海底Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆.Make up bottom hole assembly. 组合下部钻具Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.Number stands on trip out and trip in. 起下钻时给立柱编号.Pick up BHA and run to seafloor. 将下部钻具下到海底.Pick up stands. 接立柱Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱Drop TOTCO. 投(陶特)测斜仪Fish TOTCO with overshot. 用打捞筒捞起测斜仪Resume drilling to T.D. 继续钻进到总深Circulate 15 minutes.循环15分钟Run in hole. 下钻Put out of hole. 起钻Make an inventory of all ring gaskets. 开一个所有垫圈的清单Use spinning tong. 使用气动扳手Operate the air winch. 操作气动绞车Lay down 57 joints of 5” drill pipe. 甩57根钻杆Pick up drill stem test tool. 提起钻杆测试工具Circulate mud for 2 hours. 循环泥浆2小时Move string during circulation. 在循环时注意活动钻具Circulate hole clean. 循环清洗井眼Circulate bottoms up. 循环泥浆几周Fill up every 5 stands. 每5柱灌泥浆一次Check mud weight every 15 minutes. 每15分钟检查泥浆比重Reverse out excess cement. 反循环替出多余的泥浆Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆Stop drilling. 停止钻进Drilling ahead. 钻进Pull out of hole bit. 起出钻头Change bit. 换钻头Run the wear bushing. 下抗磨补心The bit thread type is regular pin. 钻头丝扣是正规公扣What’s the make-up torque? 上扣扭矩要多大?Run in 9” collars. 下9”钻铤The cathead can’t give enough torque. 猫头力量不够Connect crossover sub. 接上配合接头The tong angle is too small. 大钳的角度太小了Stop circulating. 停止循环泥浆Break out the stand. 卸立柱Set the single into the mousehole. 把这个单根放进鼠洞Can we break out the pipe with rotary table? 可用转盘卸扣吗? No! Break it out with tong. 不行! 要用大钳卸扣Spin it out with the air spanner. 用气动扳手卸扣Put the pipe wiper on the string. 装上钻杆刮泥器Don’t set this stand back. 这根钻杆不要放在钻杆盒上Make up the lift sub. 接好提升短节Secure the safety clamp. 上紧安全卡瓦The bit is nearing the shoe. 钻头快到套管鞋了Slow down the running speed. 放慢下放速度This is the undergauged interval. 这是缩径井段This is the drilling program. 这是钻井设计书How much weight on bit is required? 要加多少钻压?Keep the rotary speed at 120---140 RPM. 转速保持120---140转/分Keep the flow rate at 3000 LPM. 保持排量3000升/分The pump pressure is too high. 泵压太高了Don’t ream the hole too fast. 划眼不要太快Notice the rotary torque. 注意转盘扭矩的变化The penetration rate is getting slower. 钻速变慢了The bit is nearly worn out. 钻头快磨光了Stop drilling at 2000 meters. 钻至2000米停钻Circulate for one hour. 循环一个小时The pump pressure has increased. 泵压升高了One nozzle may be plugged. 可能有一个水眼(或: 喷嘴)堵了What is the hook load? 悬重多少?What’s the pick-up weight? 上提重量是多少?What’s the lowering weight? 下放重量是多少?Run in HWDP. 下加重钻杆A stabilizer is needed here. 这里需要一个扶正器This is a flexible sub. 这是挠性接头This is the BHA log. 这是下部钻具组合记录Record all outside and inside diameters. 记录好所有(入井工具的)内外径We need a short drill collar. 需要一根短钻铤Pull the cat line. 拉猫头Operate the break lever. 操作(或:扶)刹把Stop the pumps. 停泵Make a wiper trip. 通井Retrieve wear bushing. 取出抗磨补心Bleed off pressure. (释)放压(力)Keep 5 wraps on the drum. 滚筒上留5圈Set slips. 座上卡瓦If tight hole, repeat wiper trip. 如果井眼紧, 重复划眼Setback bottom hole assembly. 将下部钻具立于钻杆盒内Make sure all alarms are on. 确保所有的警报信号都开着Lay down TDS spinner. 拆下顶部驱动的旋扣器Run in hole bit #15 to bottom. 用15号钻头下钻到井底Run in hole to casing shoe. 下钻至套管鞋Pick up same bit and BHA. 装上同样的钻头和钻具组合Lay down 5” HW drill pipe. 甩5”加重钻杆Move string every 2 hours. 每2小时活动钻具一次Keep area around shaker clean. 保持振动筛区域干净Control trip gas. 控制起下钻气Ream if needed. 如必要时进行划眼Select the best penetration rate. 选择最佳钻进速度Fix the traveling assembly. 固定游动系统Check power tongs and spinning rope are on drill floor. 检查动力钳和尾绳是否在钻台What’s the weight on bit? 钻压是多少?What is the BHA of this well? 这口井的下部钻具如何组合?Drill out cement. 钻穿水泥Drill out 20” casing shoe. 钻穿20”套管鞋Latch the elevator. 扣吊卡Unlatch the elevator. 开吊卡Set the slips. 放卡瓦Adjust the crown-o-matic (crown saver). 调整防碰天车Lock the hook pin. 锁紧大钩销子Check OD of stabilizer. 检查扶正器的外径Perform leak off test. 进行地层破裂(或:渗漏)测试Connect kill and choke line. 接上压井和放喷管线Reverse out the drill pipe. 反循环清洗钻杆Make a short trip. 进行短途起下钻Change the cutters. 换割刀Slug the pipe. 灌重泥浆Drill the stand down. 钻完立柱Start/run the shale shaker. 开振动筛Start the desanders. 开除砂器Start the desilters. 开除泥器Change it with a 40 mesh screen. 换成40目筛布Shut it off. 关掉Pull it to the cat ramp. 把它拉到坡道上去Make a fast connection. 接单根要快Don’t dump the mud into the sea. 不要把泥浆排放到海里Disconnect it with a chain tong. 用链钳卸开Put a thread protector. 加一个(丝扣)护箍Can we use the power slips? 可以使用动力卡瓦吗?Casing and Cementing 下套管与固井Run in hole to bottom for wiper trip. 下钻通井This is the casing program. 这是套管程序Prepare for running casing. 准备下套管Make everything ready for running 7”casing. 做好下7”套管的准备Make cementing job. 固井Displace cementing with mud pump. 用泥浆泵替泥浆Set cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞Pick up cementing head. 接水泥头Cement samples are hard. 水泥样已凝固Pump in 3 cubic meters of spacer. 注3方隔离液Pump down the plug. 泵压(胶)塞Wait on cement. 候凝The guide shoe will be connected. 接引鞋Connect the floor collar. 接浮箍Connect the air line to the casing stabbing board. 接好套管扶正台的气管线Run casing with the 350T slip elevator. 用350吨卡瓦式吊卡下套管Clean and dry 20” casing threads with rags. 清洁并擦干20”套管丝扣Where is the rabbit for drifting the casing? 套管通径规在哪里?Rig Move, Anchoring and Positioning 拖航, 抛锚, 定位What is our position now? 我们现在船位在哪里?Wh at’s the moving speed now? (What’s the towering speed?) 拖航速度是多少? The speed is about 4 knots. 船速是4节左右Which one is the main tug? 主拖是哪条船?The main tug is Nanhai 205. 主拖是南海205Which one is the chase boat? 护航船是哪一条?How much is the horse power? 有多大马力?She has 6000 HP. 有6000马力Move the rig off location 50 feet. 将平台移开50英尺We are ready to drop the anchor. 我们已经做好抛锚的准备了Secure all the movable equipment. 固定好各种活动的设备Preload. (自升式)压载Ballast. (半潜式)压载Put the preload water into the tank. 向压载舱灌压压载水We need 5500 tons of preload water. 需要5500吨压载水Shall we preload right now? 马上开始压载吗?Drain the water off. 放水The rig is overloaded. 平台已超载Jack up (jack down) the rig. 升(降)船The draft is 3.5 meters. 船体吃水3.5米The jetting pressure is 100psi. 冲桩压力是100psiPenetrate the legs. 插桩How much penetration do we have? 入泥多深了?No.1 and No.2 legs indicate 10 meters. 1,2号桩腿插入10米Fix the upper and lower wedges. 固定上下楔块Pay out the anchor line. 放出锚缆绳Skid the derrick. 移开井架The rig is short of potable water now. 平台缺乏饮用水Drop No.2 and No.3 anchors. 抛2号和3号锚Why has the main engine stopped? 主机为什么停?Unleash the drilling tools. 卸开钻具Tighten up. 绷紧(或:上紧)一点Turn on the cooling water for the windlasses. 开锚机刹车冷却水Retrieve the No.1 to No.8 anchors. 起1到8号锚Check the paint marks at the anchor winches. 检查锚机上的油漆记号Prepare for a location move. 准备好移井位Commence anchor handling. 开始起锚(或抛锚)Secure all equipment stored on deck. 固定好所有存放在甲板上的设备Carry out stability and load calculations. 做稳性和载荷计算Pass pendant line, shackle and buoy to anchor handling vessel. 将起抛锚短索, 卸扣和浮标吊起给起锚船Lower the windward anchor to seafloor. 抛上风锚到海底Pick up the leeward anchor first. 先起下风锚Take anchor chaser (or chaser) back to rig. 将捞/抛锚环送回平台Hook up towing lines to tug boat. 将拖缆连接到拖轮Sound fog signal for two seconds every twenty seconds. 发大雾信号, 每20秒钟响两秒Fishing 打捞The bit cutters have been lost in the hole. 牙轮落井Run in the reverse-circulation basket. 下反循环打捞篮There is a lot of junk in the hole. 井下有很多落物The fish is 235.46 meters long. 落鱼长度235.46米The fish top is at 2478.34 meters. 鱼顶位置2478.34米Coring 取芯Stop drilling for coring. 停钻准备取芯Make up core bit. 接取芯钻头What type of core bit is it? 这是什么型号的取芯钻头? Run in a diamond core bit. 下金刚石取芯钻头Let’s drop the ball for coring. 可以投球取芯The core has been broken off. 岩芯断了Put the core in the boxes. 把岩芯装在岩芯盒里Don’t brake suddenly. 不要猛刹车Take out the core. 岩芯出筒How long is the core? 岩芯多长The core recovery is 98%. 岩芯收获率是98%Run in the core barrel again. 继续下岩芯筒(或: 取芯筒)Run in hole core barrel. 下取芯筒Drop ball. 投钢球Recover core. 取出岩芯Use same parameters as for core #1. 使用与1#取芯同样的参数Freeing Stuck Pipe 卡钻与解卡The down-hole problems are very complicated. 井下情况很复杂The hole is tight. 遇阻了Overpull while tripping out. 起钻遇卡(overpull: 超拉力)The formation is unstable. 地层不稳定The wall caving is severe. 井壁垮塌严重There are many return cuttings. 返出岩屑特别多The mud returns have decreased. 返出泥浆减少The hole is enlarged. 井眼扩大了The pipe’s stuck. 卡钻了Pull up to 150 tons. 上提150吨Slack off to 50 tons. 下放至50吨Ream down all the tight points. 在所有遇阻点进行划眼The rotary table can’t rotate. 转盘转不动Where is the sticking point? 卡点在哪里Make a tensile test. 做拉伸试验Back it off above the free point. 在卡点以上倒扣Where is the back-off position? 脱扣位置在哪Plug the well for side tracking. 打水泥塞侧钻Abnormal Well Condition and Well Control异常井况与压井The mud is gas out. 泥浆有气侵The pit has lowered quickly. 泥浆池液面下降很快The hole lost returns. 井口不返泥浆The returns are unstable. 返出泥浆量忽大忽小Where’s the thief zone? 漏失层在哪里Cut down the flow rate. 降低排量Lower the mud density. 降低比重Cut down the hydrostatic pressure. 减少静压The gas smell is strong. 天然气味度很浓There’s some trace of oil. 发现有油花The pump pressure is fluctuating. 泵压不稳It is a zone of abnormal pressure. 这是异常压力层The hole (well) is kicking! 井涌啦!Shut in the BOP! 关闭防喷器Sound the general alarm quickly! 快发出综合警报The stand pipe pressure is 10 kg/cm2. 立管压力10公斤/厘米2The casing pressure is 25 kg/cm2. 套压2510公斤/厘米2Fill out the kill sheet. 填写压井记录表Kill the well. 压井There’s a combination of lost returns and the kick. 又喷又漏, 情况复杂Reverse the gas out of the hole. 反循环排气What’s the lag time? 迟到时间是多少The well is now stable. 现在井眼已经稳定BOP and subsea Equipment 防喷器与水下设备Cut off the 30” conductor. 割掉30”隔水管Weld on the 30” bottom flange. 焊接30”法兰Hoist and nipple up 30” diverter. 吊装30”转喷器Change the 5” pipe rams to 3-1/2” rams. 把这个5”闸板换成3-1/2” Install blind ram. 安装防喷器的盲板芯子Check the seal ring of the conductor. 检查隔水管密封圈Cut off the lifting eye of the conductor. 切割隔水管耳环Test BOP. 测试防喷器Change annular BOP packing. 更换万能防喷器芯子Full pressure test the ram preventers. 对闸板防喷器进行全压试压Test annular BOP at 2500psi. 万能防喷器试压至2500psiCheck annular pressure. 检查环形空间压力Confirm the angle of the guide base. 确定基板角度The thread is covered with the quick-release protectors. 已戴好快卸护丝Establish the guide lines. 装导向绳Connect the TGB running tool. 接临时导向基板送入工具Land the TGB to sea. 下临时导向基板到海底Retrieve the running tool. 退出送入工具Run the BOP and risers. 下防喷器和隔水管Pick up the marine riser. 吊出隔水管Pick up the slip joint. 起伸缩节Adjust the riser tensioners. 调整隔水管张力Function test the diverter system. 对防喷器系统进行功能测试Retrieve the pin connector. 取出销钉连接器Move the BOP to the moonpool door. 将防喷器移到园井甲板的活动门上Run the test plug. 下试压塞Close the upper pipe ram. 关上部钻杆闸板防喷器Open the kill line valve. 开压井管线阀The compensation capacity is 400000 pounds. 补偿能力是400千磅The locking load is 1000000 pounds. 锁紧负荷1000千磅Support the riser. 接隔水管支撑环Remove the hose bundles. 卸下垮接软管Assure the self-controlled rotation. 保证自控转动Set the LMRP on the test pump. 将下部防喷器插入总成座放到试压桩上Connect the flex joint to the riser. 连接隔水管与挠性接头Land the BOP onto the well head. 座防喷器到井口头Run the subsea TV for monitoring. 下水下电视观察Remove all the riser running tools. 取出所有的隔水管送入工具BOP carrier. 防喷器叉车Lower the universal guide frame. 下放万能导向架Paint mark the top 6 meters of 30” conductor white. 在30”隔水管的顶部6米处用白漆涂上记号Check adequate length for guidelines. 检查导向绳的长度是否足够Move temporary guide base (TGB) into moonpool. 将临时导向基板到园井甲板Test pull to check connection. 试拉检查连接Grease TGB and running tool as required. 按要求给导向基板及下入工具上黄油Test fit TGB and running tool. 用下入工具试临时导向基板连接Check for junk inside shoe joint. 检查浮鞋内有无落物Pick up 30” conductor handling slings and shackles. 吊上下30”导管的索具和卸扣Is slope indicator properly mounted? 水平仪是否装好?Ensure subsea TV is in good condition. 确保水下电视处于良好的状态Place BOP stack on the test pump. 将防喷器组放在试压桩上Check condition of all 30” casing connectors. 检查所有30”套管接头的情况Replace O-rings as required. 按需要, 更换O性密封圈Attach slope indicator below camera position. 在摄像机下面装上水平仪Inspect and repair diverter. 检查并修理转喷器Prepare spud plate and wireline to check water depth. 准备测深板和钢丝绳测量水深Record all pressure tests on a chart recorder. 用试压表记录试压记录Visually inspect all sealing element. 目视检查所有密封件Check and tighten all bolts. 检查并上紧所有螺栓Bleed off surface accumulators. 地面管线排空气Check for leaks. 检查有无泄漏Lift BOP stack and replace wellhead connector AX ring. 吊起防喷器组并更换连接器AX密封圈Function test wellhead. 对井口头进行功能试验Fill kill and choke valves with seawater. 将压井阀和阻流阀注满海水Pressure test to 500psi then bleed off test pressure. 试压到500psi, 然后放掉压力Reduce hydraulic control manifold pressure to 5200 kpa. 将液压控制管线压力减少到5200千帕Switch to alternate control pod. 把闸门开关倒到控制面板Guidelines are slacked off. 导向绳松了Slack off drill pipe and release running tool. 放松钻杆并卸开下入工具Run subsea TV to observe bit entering the TGB. 下水电视观察钻头是否进入临时导向基板Don’t rotate until ho le opener passes through the TGB. 在扩眼器通过临时导向基板前不要旋转Position permanent guide base (PGB) below rotary table. 在转盘下安放永久导向基板Monitor riser level via trip tank. 用计量罐来控制隔水管内的液面Pressure test to 5000psi. 试压5000psiPick up test mandril and place in BOP. 吊起试压防喷器芯子并装入防喷器组Safety and Firefighting 安全与消防Get a Work Permit before you can start the hot work. 办理作业许可证才能进行动火作业Welding is not allowed. 不准动焊Put on your (safety) helmet. 戴上安全帽It’s a high voltage area. 这是高压区That’s against the rule. 这是违章作业Don’t walk under the crane load. 不要在吊物下走动The repairing is under way. 正在检修Keep your hands clear! (Keep you hands off! Do not touch!) 不要乱动Wear and secure your safety belt. 戴上并系好安全带Life jacket must be worn when working outboard or overhead. 舷外或高空作业要穿救生衣Have your breathing apparatus near you. 保持放毒面具在附近It’s a drill. 这是演习It was a BOP drill. 这是防喷演习Get in the lifeboat in order. 按顺序进入救生艇Put on life jacket! 穿好救生衣Abandon the vessel! 弃船Sound the abandonment alarm! 发出弃船警报Go to the helideck! 去飞机坪集合Aboard the lifeboat. 登上救生艇Aboard the supply boat to shore! 乘拖船上岸Check life saving apparatus periodically. 定期检查救生设备It’s for fire fighting. 这是消防用的Start the fire pump. 启动消防泵This rope is too small. 这根绳子太细了It should be function tested. 需做功能测试A warning notice should be set up. 要挂警告牌Do you have an emergency program (contingency plan)? 你们有没有应急计划?It must be ready in an emergency condition. 必须始终保持良好的应急状态Will the typhoon hit our rig? 台风要袭击我们的平台吗?We will have to evacuate the rig. 我们要撤离平台Personnel on board (POB). 在船人员总数Sound fire alarm. 发消防警报This is a fire drill. 这是消防演习conduct abandon ship drill. 举行弃船演习Release the boat hooks. 释放救生艇吊钩Board the life boat. 登救生艇Remove the rust and paint with anti-corrosive primer. 除锈后上防锈底漆Three rafts are located near life boat station port side. 在左舷救生艇站附近还存放有3个救生筏Wear work vests when working below the cellar deck. 在圆井甲板面下面工作时须穿工作救生衣The station bills need to be updated. 应急部署表须更新Check the expiry date for all foam extinguisher. 检查所有泡沫灭火器的过期时间Close all the water-tight doors. 关闭所有水密门Safety procedure shall be followed at all the times. 在任何时候都应遵守安全程序Anchor wires should have a Spelter type socket at anchor side. 抛锚绳靠锚的一端应使用锌压头Colour code all the connection at the loading station. 在供给站管线接头处用颜色表明各管线Verify that a high level alarm is installed on the sludge tank. 确认污水舱安装有高位警报Don’t switch on during drilling operation. 钻井作业期间不能合闸Provide two independent means to start the emergency generator engine. 应急发电机柴油机应有两套独立的起动方法Have the boom pennant wires of port crane re-certified. 重新认证左舷吊车扒杆变幅绳Clean the internals of the emergency switchboard. 清洁应急配电盘内部Helicopter and Supply Vessel 直升机与供应船Load out Contractor’s riser at Zhanjiang anchorage. 在湛江锚地把承包商的隔水管装上平台Offload casing. (从供应船上)卸套管Load (offload or unload) the boat. 装(卸)船Get the food container loaded on the boat. 把食品集装箱装上船The helicopter will land on rig soon. 直升机很快就要在平台降落Tell the base to get (or send) a chopper here. 通知基地派飞机来Helicopters are not allowed to land here. 飞机不能降落Report the weather condition to the pilot. 向飞行员报天气Inform the boat come to standby. 通知拖轮过来待命Call the boat to come along port side. 通知拖轮过来靠左舷We will take the personnel basket. 我们乘坐吊篮。
海上采油英语实用手册(英汉对照)-单词及短语
Word and Phrases单词及短语柴油储罐一、The Process And Equipment OfOil Production采油工艺及设备差压控制阀1.atmospheric vent放空阀23.dispersed gas floatater加气浮选器2.auto-drain valve自动排放阀24.displacement oil pump置换油泵3.backwash return pump反冲洗循环泵25.drain pit排放池4.blind spectacle plange双孔盲法兰26.electric desalter电脱盐器5.blowdown vessel排放罐27.electric - hydraulic valve电液控制阀6.boiler make-up pump锅炉提升泵28.electrical submergible电潜泵7.centrifugul pump离心泵29.emergency shutdown valve紧急关断阀8.chemical seal化学密封30.fine filtration scour blower细滤器洗刷风机9.clean water surge tank净化水缓冲罐31.first (second) stage separator一(二)级分离器10.close drain tank闭式排放罐32.flare assembly火炬燃烧总成11.coalescer聚集器33.flare pilot gas火炬点火气12.condensate drum冷凝液罐34.floater controlled valve浮球控制阀13.corrugated plate incling separator(CPI separator)波形斜板隔油器35.FPSU-floating oil production and storge unit浮式生产储油系统14.crude cooler原油冷却器36.free water knock - out自由水分离器15.crude heat exchanger原油热交换器37.fresh water maker unit淡水制造装置(造水机)16.crude sucition strainer原油吸入滤器38.fuel gas heater燃烧气加热器17.D/P - drilling and production platform钻采平台39.fuel gas system燃烧气系统18.deaeration tower除氧塔40.fusible plug易熔塞19.dehydration preheater脱水与预热器41.heat traced pipeline伴热管线20.diaphragm valve薄膜调节阀42.heater加热器21.diesel storage tank柴油储罐43.heater treater feed pump热处理器供液泵22.differential pressure control valve差压控制阀44.high pressure condensate drum高压冷凝水罐45.high pressure gas knockout drum(HP gas K.O drum)高压燃料气分离器69.process module工艺模块46.high-high pressure separator(HHP separator)高高压分离器70.production manifold生产管汇47.hose connection软管接头71.production train shutdown panel生产系列关断盘48.hydraulic lines液压管线72.sample connection取样接头49.hydraulic operated valve液压控制阀73.sand filter 砂滤器50.hydraulic piston pump水力活塞泵74.sans scrubber 砂净化器51.ignitor点火器75.screw pump螺杆泵52.insrlation flange绝缘法兰76.scum vessel渣油罐53.jet pump射流泵77.solenoid operated with manual reset valve手动复位电磁阀54.jump hose(jimper hose)跨越软管78.solenoid valve电磁阀55.LCP-local control panel就地控制盘79.seawater coarse filter海水提升泵56.low perssure flare低压燃烧火炬80.self-contained pressure regulation valve自给式压力调节阀57.main boiler主锅炉81.service water supply system服务水供给系统58.main process lines主流程管线82.silencer清音器59.normally open(close)valve常开(关)阀83.skimmer撇油器60.oily water tank含油污水舱84.slop tank沉降罐,污油罐61.package equipment组块设备85.snubber缓冲器、减振器62.pig larncher清管球发射器86.SSSV-subsurface safety valve井下安全阀63.plate attachment板间连接件87.SSV-subsurface safety valve井口安全阀64.pneumatic operated valve气动控制阀88.steam distribution system蒸汽分配系统65.pneumatic operated with manual reset valve手动复位气动阀89.steam radiator蒸汽散热器66.position light状态灯90.submarine pipeline(subsea pipeline)海底管线67.pressure regulation valve压力调全阀91.swivel joint旋转接头68.pressure safety valve压力安全阀92."T"type strainer T型过滤器93.test manifold计量管汇94.transfer pump输送泵95.tube side of exchanger热交换器管程96.vacuum pump呼吸阀97.vacuum puessure relief valve真空泵98.vacuum injection coarse filtration package注水粗滤撬块99.water softener水软化器100.well space井口区二、The equipment of storage and loa储输装置1.access hatch 甲板舱口23.duplex filter双联滤器2.access up/down甲板上/下走道24.electric capstan电动绞缆车3.after peak tank艉尖舱25.emergency air reservoir应急空气瓶4.after winch船尾绞车26.export tank外输油轮5.air releaser除气器27.floating hose飘浮软管6.artomatic drainer自动排流器28.flow low limit低限流量7.ballast pump压载泵29.fore peak tank艏尖舱8.ballast wing tank压载侧舱30.fore castle艏楼甲板9.barge bumper靠船碰垫31.galley厨房舱10.batch sequence批量控制程序32.hawser系泊缆11.blind flange盲板法兰33.heating medium circulation pump热介质油循环泵12.boat landing platform靠船台34.heating medium drain tank热介质油排放泵13.bow winch船头绞车35.hose connection软管连接14.celler deck底甲板36.hydraulic winch package液压绞车撬块15.cleaning machine for cargo tank油舱清洗机37.initial flow初始流量16.closed paddle blind闭式闸盲板38.insulating flange joint隔离法兰连接17.collection sump收集坑（池）39.jacket walkway platform导管架人行道18.conductor installation platform导管架固定甲板40.kingpost将军柱19.crude loading (export) pump原油外输泵41.line size change管线尺寸改变20.crude storage tank原油储输（舱）42.loading arm输油臂21.crude transfer pump原油输送泵43.loading condition装载条件22.discharge muffler释放消音器44.lower deck下甲板45.machine room机舱69.specification break技术规范变化46.meter / prover unit计量/标定装置70.SPM frame support单点支撑构架47.middle deck中甲板71.stripping pump扫舱泵48.mooring head系泊头72.swivel joint旋转接头49.mooring head pitch bearing系泊头纵摇轴承73.tandem mooring串靠系泊50.mooring jacket系泊导管架74.thermal insulation热绝缘51.mooring leg系泊腿75.towing meter拖力计52.mooring structure系泊结构76.turbine flowmeter涡轮流量计53.mooring weight系泊配重77.upper deck上甲板54.mooring winch系泊绞车78.vent stack , vent line排烟道、放空管55.multi - path swivel多通道旋转头、多通道转盘79.water ballast tank压载水舱56.oily water drain system含油污水排放系统80.water barrage防水罩57.overboard舷外81.winch control pannel绞车控制盘58.piping specialty item管线专用项82.Y - type strainer Y型过滤器59.pneumatic gangway ladder气动舷梯60.process tank工艺舱61.production deck生产甲板62.production deck support生产甲板支架63.programmable logic controller可编程序逻辑控制器64.pump room泵舱65.retaining beam固定架66.roller bearing greasing sy滚动轴承注油系统67.soft yoke柔性轭架（软钢臂）68.spacer ring隔环（垫圈）三、Control instrument控制仪表1.callar shutdown panel (CSDP)井口系统关断盘，进口系统控制盘24.instrument air supply仪表气气源2.central control panel (CCP)中央控制盘25.level control valve (LCV)液位控制阀3.central control room (CCR)中央控制室26.level indicator (LI)液位显示器4.emergeney light应急灯27.local control panel就地控制盘5.emergency shutdown system应急关断系统28.local indicating light就地控制灯6.emergency shutdown valve (SDV)应急关断阀29.local shutdown panel就地关断盘7.flow control valve (FCV)流量控制阀30.local totallizing现场累加8.flow element流量元件31.locally mounted instrument现场仪表9.flow indication controller (FIC)流量显示控制器32.low level alarm (LSL)低液位报警器10.flow quantity recorder (FQ)累计流量计33.low level smitch (LSL)低液位开关11.flow quantity device (FE)限流器34.low pressure alarm (PAL)低压报警器12.flow straightening vanes稳流栅35.motor control center (MCC)电动机控中心13.flow transmitter流量变送器，流量传送器36.multifunction power record多功能功率记录仪14.high pressure alarm (PAH)高压报警器37.multifunction temperature 多功能温度记录仪15.high pressure differential alarm 高压差动报警器38.navigational light导航灯16.high pressure differential switch高压差动开关39.orifice plate孔板17.high temperature alam (TAH)高温报警器40.pilot light (indication la指示灯，引导灯，显示灯18.high-high level switch (LSHH)高高液位开关41.position light (ZL)状态灯19.high-high pressure switch (PSHH)高高压力开关42.position switch (ZS）状态开关20.high/low pressure switch (PSHL)高/低压力开关43.positive displacement mete容积式流量计21.high/low temperature switch (TSHL高低温开关44.pressure control valve压力控制阀22.indication lamp test switch指示灯试验开关45.pressure differential indi差压显示器23.instrument with two services or f同时具有两种功能或性能的仪表46.pressure indication contro压力显示控制器47.pressure indicator (PI)压力显示器48.pressure multifunction rec多功能记录仪49.pressure regulation valve压办调节阀50.pressure safety element (P压力安全膜片51.pressure transmitter(PI)压力变送器52.production shutdown panel(生产系统关断盘，生产系统控制盘53.pump stop switch停泵开关54.rotameter转子流量计55.shutdown switch关断开关56.shutdown valve关断阀57.temperature control valve(TCV)温度控制阀58.temperature control(TC)温度控制器59.temperature indicator温度指示器60.temperature well(TW)测温孔61.test separator shutdown panel(TSD计量分离器关断盘62.venturi or nozzle文丘里管或喷嘴四、Machinery机械类1.after winch船尾绞车23.electrcal submergible pump电潜泵2.antisweat防渗24.electrically traced电伴热3.artificial lift pump人工举升泵25.emulsion trabsfer pump乳化油输送泵4.automatic air pump自动排气26.evaporator蒸发器5.automatic air/vacume release自动呼气27.expansion bellows膨胀伸缩式波纹管6.backwash return pump反冲洗循环泵28.expansion joint膨胀接头7.barge bumper靠船碰垫29.flame arrestor阻火器8.blowndown valve泄压阀（放空阀）30.flex connector挠性连接9.boiler make-up pump锅炉提升泵31.floating hose漂浮软管10.bow winch船头绞车32.fresh water maker unint淡水制造装置、造水机11.centrol control room中控室33.fuel oil system燃油系统12.cold conservation保冷34.heat conservation电伴热、保温13.condensate drum冷凝液罐35.heater加热器14.conductor installation platform导管架固定板36.hose reel软管滚筒15.cooling water return冷却水回水37.hydraulic piston pump水力活塞泵16.cooling water supply冷却水源38.hydraulic winch package 液压绞车撬块17.diesel storage tank柴油储罐39.ignitor点火器18.direct acting正作用40.incinerator焚烧炉19.displacement oil tank置换油罐41.insulating flange joint隔离法兰连接20.duplex fiter双联滤器42.jet pump射流泵21.ejector喷射器43.line end termination管线终端22.electric oapstan电动绞缆机44.line size change管线尺寸改变45.liquid seal液体密封69.pump room泵房46.machine room机舱70.quick release hook快速解脱钩47.main boiler 主锅炉71.remote operated遥控阀48.main switchgear room主配电间72.retaining beam固定梁49.mooring head系泊头73.riser clamp立管卡子50.mooring head pitch bearing系泊头纵摇轴承74.roll/pitch articulation横摇/纵摆绞接头51.mooring jacket 系泊导管架75.roller bearing greasing sy滚动轴承注油系统52.mooring structure系泊结构76.roller bearing water barra滚动轴承防水罩53.mooring winch系泊绞车77.rotary oil burner旋转燃烧器54.motor operated valve马达驱动阀78.sample connetion取样接头55.mutli path swivel多通道旋转头（多通道转盘）79.seam to seam缝对缝56.normally open常开80.seawater lift pump海水提升泵57.package equiment组块设备（撬装设备）81.service water supply syste用水供给系统58.personnel protection个人保护82.set point设定点59.pig launcher清管球发射器83.shell side of exchanger热交换器壳60.plate attachment扳间连接件84.silencer消音器61.plate type exchanger板式热交换器85.space ring隔环62.pneumatic gangway ladder气动舷梯86.SPM frame support单点支撑构架63.power liquid动力液87.status light状态灯64.power water动力水88.steam boiler蒸汽锅炉65.preheater预热器89.seteam rediator蒸汽散热器66.pressure differential rilief valv差压安全阀90.stress relieve消除应力67.pressure safely valve压力安全阀91.surface safely valve(ssv)地面安全阀68.production deck support生产甲板支架92.swivel joint旋转接头93.tangent to tangent切面对切面94.trap疏水器95.vapor blower蒸汽鼓风机96.ventilation fan排风扇97.water softener水软化器98.well killing pump压井泵99.winch braker 滚筒刹车五、Electricity电气类1.aeronautical radio system航空无线电系统23.emergency air reservoir应急空气瓶2.alarm acknowledge switch 报警确认开关24.emergency fire pump room应急消防泵房（间）3.ammeter电流表25.emergency generator engine应急发电机引擎4.annumciator信号器(报警器)26.emergency light应急灯5.ballast pump压载泵27.emergency power station应急电站6.burner motor燃烧器马达28.emergency radio system应急通讯系统7.changing room更衣室29.emergency shutdown system应急关断系统8.chilling water thermostat冷却水恒温器30.emergency switch board应急配电板9.circuit breaker open断路器打开31.emergency switchgear room应急配电间munication system通迅系统32.export pump外输泵11.uninterrupted power supply(UPS)不间断电源33.fail to crank盘车失败12.control bus 控制总线(母线）34.fail to start启动失败13.crew cabin船员室35.fan room风机室14.D.C emergency supply直流应急电源36.fire fighting equipment ro消防设备间15.deep freeze compressor深冷压缩机37.flood light泛光灯16.discharge muffler释放消音器38.flow recorder流量记录仪17.electric capstan电动绞缆车39.flow restriction device限流器18.electric main fire pump电动主消防泵40.fluorescent lamp荧光灯19.electric trace电伴热41.frequncy频率20.electrical duct]电缆通道42.gas turbine power generato燃气透平发电机21.electrical single line diagram电路单线图43.general service pump总用泵22.emergency air compressor应急空压机44.generator synchronizing发电机同步45.halon fire protection海伦火灾保护69.power failure电源故障46.high pressure alarm(PAH)高压报警器70.pressure indicaion(PI)压力显示器47.high/low pressure switch(PSHL)高低压开关71.pressure indication contro压力显示控制器48.hour counter计时器72.pressure transmitter(PT)压力变送器49.ignition failure点火失败73.prodution shutdownpanel(PS生产系统关断盘50.illumination level照明度74.pump stop switch停泵开关51.incandescent lamp白炽灯75.radio battery room无线电蓄电池间52.indication lamp test switch指示灯试验开关76.radio equipment无线电设备53.individual auto synchronizer独立式自动同步器77.radio room报务室54.insulation material 绝缘材料78.radio telegraph无线电报55.insulation thickness绝缘厚度79.radio telephone无线电话56.loading condition装载状态80.recreation room娱乐室57.mail battery room主电瓶间81.removable insulation可卸式绝缘58.main switch room主配电间82.reset switch复位开关59.marine radio system船用无线电系统83.slop pump污水泵60.mobile radio system移动式无线电系统84.smoking room吸烟室61.motor control center(MCC)电动机控制中心85.start push button启动按钮62.navigational light导航灯86.stripping pump扫舱泵63.obstructionlight障碍灯87.store room储藏室64.over voltage过电压88.summary switch gear signal即时配电设备信号65.overspeed过速89.temperature controller温度控制盘66.pilot light(indication lamp)指示灯90.thermal conductivity导热系灵数67.platform-to-shore radio system平台-海岸无线电系统91.thermal insulation热绝缘68.portable radio for life boat逃生电台92.transfer pump输送泵93.transformer room变压器间18.explosion proof eqvipment防爆设备94.under voltage低电压19.explosion proof divisional防爆隔离墙95.unloading condition卸载状态20.extinguisher灭火器96.vent fan排风扇21.fire alarm box火灾报警盒97.very high frequency radio telepho甚高频电话22.fire control panel火灾控制盘98.voltmeter电压表23.fire fighting system消防系统六.Safety安全24.fire house消防站1.air foam chamber空气泡沫室25.fire hydrant消防栓2.air foam extinguisher空气泡沫装置26.fire proof door防火墙门3.audible alarm音响报警27.fire pump消防泵4.auto fire alarm system自动火灾报警系统28.fire push button 消防按钮5.auto/manual locked-out selector s手动/自动连锁选择开关]29.fire triangle 燃烧三角形6.bilge/fire pump舱底污水/消防泵30.fire water消防用水7.breathing apparatus防毒面具31.fire water life pump消防水提升泵8.carbon dioxide extinguisher二氧化碳灭火器32.fire-proof wall防火墙9.clear signal明显信号33.first aid kit急救箱10.cold work冷工作业34.foam deluge system水喷淋系统11.collision mat堵漏毯35.foam extinguishing system泡沫灭火系统12.damper reset valve box风门复位开关36.foam mixer泡沫混合器13.dry chemical extinguisher干粉灭火器37.foam monitor remote contro泡沫枪遥控盘14.distress signals救生信号38.foam/water pun泡沫/水枪15.docking sonar system入港声纳系统39.gas detecting alarm system可燃气探测报警系统16.emergency push button应急按钮40.gas detector可燃气探测器17.escape line逃生路线41.gas monitor panel可燃气监测盘42.halon cylinder海伦瓶66.light type combustible gas轻型可燃气体探测器43.halon discharge indicaor海伦释放器67.line throwing appliances抛绳设备44.halon extinguisher海伦灭火器68.main fire water ring消防主环形管路45.halon fire system海伦消防系统69.noise limit噪音限制46.halon local panel海伦就地控制盘70.noise pollution噪音污染47.halon manual switch海伦手动开关71.non-combustible不可燃物质48.halon nozzle海伦喷嘴72.non-directional navigation不定向航行警标49.halon portable extinguisher手提海伦灭火器73.oil concentration 含油浓度50.hazardous area危险区域74.oil fence围油栅51.hazardous area classfication 危险区等级75.oil fence reel围油栅卷筒52.heat actuating alarm system测温火灾报警装置76.oil pollution原油污染53.heat detector热探测器77.personnel protection人身保护54.high concentration gas alarm高浓度可燃器报警78.piston releaser活塞式释放55.hose box软管箱79.process drain生产流程排放56.hose station软管站80.rescue boat救助艇57.hot work明火作业81.restricted area限制区58.HS detecting alarm system硫化氢检测报警系统82.safety equipment安全设备59.life boat救生艇83.safety zone安全区60.life boat davit吊艇架84.smoke detector烟探测器61.life boat landing area救生艇登乘处85.spilled oil recovery溢油回收62.life buoy救生圈86.static electricity dischar静电释放63.life jacket救生衣87.survival belt救生带64.life saving appliances救生设备88.survival craft救生筏65.life saving system救生系统89.ultra-violet detector紫外线探测仪90.warning alarm报警系统19.dissolved gas oil ratio油解油气比91.water curtain水幕20.driver head驱动头92.water extinguishing system水灭火系统21.dynamic fliud level动液面93.wheeled extinguisher轮式灭火器22.ESP=electric submersible p电浅泵94.work boat工作艇23.extender加长短节，电机引线七.Mechnical Oil Production机械采油24.flat cable扁电缆1.artificial lift人工举升25.flow rate at cavitation po气蚀流量2. B.H.P.=bottom hole pressure井底压力26.flrid level surveyor液面测试仪3. B.H.P.=brake horse-power制动功率27.free gas游离气，自由气4.bleed valve泄油阀28.gas lift(valve)气举（阀）5.cable shield电缆护罩29.GOR=gas oil ratio油气比6.casing套管30.hydraulic horsepower水马力7.casing-tubing communicator油套连通器31.in-site gas oil ratio就地油气比8.check valve单流阀32.interlock/self-lock互锁/自锁9.centrifugal pump离心泵33.jet pump射流泵10.control line of safety valve安全阀控制管线34.juction box接线盒11.control pressure控制压力nding nipple座落接头12.control circuit控制回路36.lock mandrel锁心13.current dial电流记录卡37.lock/unlock锁定/释放14.current recorder (diagrammer)电路记录仪38.main circuit主回路15.dead oil死油，脱气油39.motor电机16.dead oil viscosity死油粘度40.motor base电机底座17.diffuser tube扩散管41.nozzle喷嘴18.dissolved salt content in fornati地层水溶解盐量42.non-welded staor centraliz非焊接式定子扶正器43.oil(water,gas)viscosity油（水，气）粘度67.sand content含砂量44.oil filled pump注油泵68.SCSSV(surface control subs地面控制井下安全阀45.overload过载69.secondary circuit次边回路，第二回路46.packer封隔器70.setting voltage(current)设定电压/电流47.PCP(progressive cavity pump)螺杆泵，空腔进动泵71.special well head for ESP电潜泵专用井口48.permanent packer永久封隔器72.SPM(side pocket mandrel)偏心工作筒49.power flat(rornd)cable动力扁（圆）电缆73.SSSV(subsurface safety val井下安全阀50.power liquid/water动力液/水74.SSV(suface safety valve)地面安全阀51.power liquid pressure动力液压力75.static fluid level静液面52.power liquid rate动力液量76.stator定子53.power cable动力电缆77.stock oil死油粘度，商品油54.prodution oil gas ratio生产油气比78.stride packer双管封隔器55.protector/balacer保护器/平衡阀79.sucker rod抽油杆56.PSI(pressure sensor&instrument)压力/温度传感器80.sulpher content含硫量57.pump body泵体81.switchboard配电盘（开关屏）58.pump outlet pressure泵出口压力82.tail pipe尾管59.pump suction pressure泵入口压力83.test/production plug测试/生产堵塞器60.pump setting depth泵挂深度84.throat喉管61.rating voltage(current)额定电压/电流85.transformer 变压器62.rod centralizer抽油杆扶正器86.tubing油管63.RODEMIP(PCP)螺杆泵87.tubing head油管头64.rotor转子88.tubing head hanger油管挂65.round cable圆电缆89.twin(dual)string tubing ha双管油管挂66.safety valve安全阀90.tein(dual)string X-mass tr双管采油树91.underload欠载14.areal drive面积驱油92.VSD=variable speed driver变速器，变频器15.asphaltene沥青质93.WC=water cut含水率，水侵量16.back flow回流，反循环洗井94.WHP=well head pressure井口压力17.back pressure回压95.WHT=well head temperature井口温度18.backwash 反洗96.wax content含蜡量19.bean back减小油嘴97.well bore井筒20.beam unit油梁抽油机98.working voltage/current工作电压/电流21.bean up放大油嘴99.X-mass tree=Christmass tree采油树22.blank pore死孔隙100.Y-connector“Y”接头23.bottom hole pump井下泵八.Petroleeun Geology 石油地质24.bottom water drive底水驱动1.abandonmont pressure 油层枯竭压力25.boundary边界2.abandoned well报废井26.brige type mandrel桥式配产器3.abnormal pressure异常压力27.build-up curve压力恢复曲线4.acid attack酸蚀28.build-up of pressure压力恢复5.acid fructuring treatment酸压裂处理29.cavitation气蚀6.acidify酸化30.center to edge flood顶部注水，中央注水7.accumulation of injected water累积注水量31.chanelling水窜8.addition agent 添加剂32.chock(choke)油嘴9.additional oil recovery增产油量33.clay stabillizing agent粘土稳定剂10.adjustable bean可调油嘴34.clear area有效面积11.air lift气举35.closd-in pressure关井压力12.allocation配产mbusion drive火烧驱油13.aquifuge隔水层busite WOR综合油气比38.contineous flow gas lift 连续流动气举ction valve排气阀39.counter-flush反循环洗井tor气举管40.cumulative production累计产量64.elastric drive弹性驱动41.cusping形成水舌65.enhanced recovery techniqu强化采油技术42.cyclic flooding周期注水66.enjector pump喷射泵43.damage removal解堵67.enrich富化44.dead well废井68.evaluation评价45.decline rate递减速度69.exhausted well枯竭井46.deep well pump深井泵70.fill in well加密井47.demulsifying agent破乳剂71.fish井下落物48.depleted formation枯竭层72.fishing job打捞作业49.depletion drive溶解气驱73.fishing tool打捞工具50.depth of plunger泵深74.flood front注水前缘51.determing depth of fluid测液面75.flooded strata水淹地层52.development program开发方案76.flood-response time注水见效时间53.drainage radius泄油半径77.fluid entry profile产液剖面54.drawdown test降压试井法78.flowing pressure流动压力55.dual-pipe production 双管采油法79.flowing tubing head pressu油管压力56.dynamometer card示功图80.flowing well自喷井57.eccentric mandrel偏心配水气81.foam泡沫58.echo meter回声仪82.foaming agent起泡剂59.echogram回声图83.forced oil production强化采油60.edge water drive边水驱84.formation evaluation产层评价61.edge water encroachment边水侵入85.formation gas-oil ratio地层油气比86.formation damage removal油层解堵110.immersidle pump沉没泵87.fracturing pressure破裂压力111.initial water break throug开始水窜88.free piston气举活塞112.inflow performance curve流入动态曲线89.frontal displacement前缘躯替113.injectivity and productivi注采能力90.gas anchor气锚114.injection-production equil注采平衡91.gas condensate field凝析气田115.injection interval注水井段92.gas drive气压驱动116.injectivity and productivi注水能力93.gas leadage气窜117.input profile注水剖面94.gas lift(valve)气举118.interference test干扰实验95.gas lift mandrel气举工作筒119.intertonguing舌井96.gas oil ratio气油比120.intermittent flow间歇自喷97.gas water surface气水界面121.kick-off valve气举启动阀98.gas zone含气带122.kill line压井管线99.gelling agent凝胶剂123.kill string压井管拄100.guide导向器124.knife a well油井清蜡101.gushing well自喷井125.leakage test漏失实验102.high water cut高含水126.leak resistance防漏103.horse head驴头127.line drive线性水驱104.huff-and-puff蒸汽吞吐128.main oil-bearing region主要含油区105.hydravlic pump水力活塞泵129.massive hydraulic fracturi大型水力压裂106.hydrofracturing水力压裂130.match匹配107.hydrophilic亲水的131.measuring dynamoeter diagr测示功图108.hydrophobic亲油的132.mechanical recovery机械采油109.hystersis滞后现象133.medium water cut well中含水井l type shoe磨鞋158.pilot area实验区135.miscible phase recovery混相区开采159.pilot flood试注水136.multiphase system多相系统160.pilot teat unit生产实验区137.multizone well test分层测试161.pllunger flood活塞气举138.natural drive自然驱动162.point water flooding点状注水139.nozzle喷嘴163.polymer flood聚合物驱油140.oil drain泄油164.positive reserves探明储量141.oil displacement驱油165.possible reserves可能储量142.oil originally in place地质储量166.pressure drop压力降143.off production停产167.pressure responsed curve压力响应曲线144.oleophilic亲油的168.pressure survey 测压145.oleophobic憎油的169.primary recovery一次采油146.open hole裸眼井170.producing pressure differe生产压差147.open-line production无嘴采油171.producing test试采148.over-all gas-oil ratio总油气比172.production engineering采油工程149.packer封隔器173.production history采油曲线150.packer seat封隔器座174.production on artificial l机械开采151.pattern drive面积驱油175.production platform采油平台152.pay section生产层厚度176.productive interval生产层段153.payzone产层177.productive life开采期154.PCF(production control facility)采油控制装置178.productivity生产率155.permeabilty渗透率179.productivity index采油指数156.permeabilty-saturation curve渗透率--饱和度曲线180.profile-log of water injec注水井吸水剖面157.petroleum engineering石油工程181.proppant支撑剂182.proppant concentration支撑剂浓度206.selective water injection选择性注水183.proration限产207.selective water plugging选择性堵水184.prospect well探井208.separate;layer pressure分层压力185.proved reserves探明储量209.separate layer water cut分层含水率186.pumping head泵压头210.shot density 射孔密度187.reciprocating motion往复运动211.shut in well关井188.recoverable reserve可采储量212.single tubing string produ单管采油189.recovery gas-oil ratio开采油气比213.skirt引管，导流管190.recovery rate 开采速度214.slug段塞191.reservoir stimulation油层改造215.solubility溶解剂192.residual oil saturation残油饱和度216.solvent溶剂193.reverse pressure perforating负压射孔217.stage-gas-lift多级气举194.rodless pump无杆泵218.standing valve固定凡尔195.rotary shoe铣鞋219.static bottom hole pressur井底静压196.safety measures安全措施220.static casing pressure静套压197.sample taker取样器221.static fluid level静液面198.sampling取样222.static pressure静压199.sand consolidation固砂223.steam flooding蒸汽驱200.sand control防砂224.stimulation增产措施201.sand up砂堵225.sting production多管采油202.sand well出砂井226.stuffing box防喷盒203.saturation饱和度227.submersible motor潜油电机204.secondary recovery二次采油228.sucker rod 抽油杆205.segregation drive重力驱油229.sucker rod pump杆式泵230.sudden water influx暴性水淹231.surfactant表面活性剂232.surging well间歇自喷井233.swabbing抽吸234.sweep area扫油面积235.typered string 变径油管236.tertiary recovery三次采油237.thermal recovery热力采油238.tracer示综计239.transitional belt(zone)过渡带240.travelling valve游动凡尔241.type of drive驱动类型242.tubing pump管式泵243.tubing spear油管打捞矛244.tubing string油管拄245.ultimate recovery最终采收率246.ultimate life极限寿命247.ultra-low viscosity oil超低粘度油248.undersaturated sand欠饱和油藏249.viscos crude oil粘性原油250.viscosity粘度251.walking beam游梁252.water block水堵254.water cone水锥255.water cut含水256.water drive水驱257.water fingering水指进258.water flood project注水方案259.water influx rate水侵速度260.water out水淹261.water swept zone水淹层262.water treatment水处理263.wellhead fitting井口装置配件264.well interference井的干扰。
海洋石油钻井常用英语手册13378
海洋石油钻井常用英语手册A Handbook of English for Offshore Oil Drilling海洋石油钻井常用英语手册Drilling 钻井1. Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业.2. Prepared bell nipple. 准备”喇叭口”短节.3. Make up 2 joints of drill pipe. 接两根钻杆.4. Break out this connection. 卸开该接头.5. Run hole opener to sea bed. 下扩眼器到海底6. Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆.7. Make up bottom hole assembly. 组合下部钻具8. Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.9. Number stands on trip out and trip in. 起下钻时给立柱编号.10. Pick up BHA and run to seafloor. 将下部钻具下到海底.11. Pick up stands. 接立柱12. Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱13. Drop TOTCO. 投(陶特)测斜仪14. Fish TOTCO with overshot. 用打捞筒捞起测斜仪15. Resume drilling to T.D. 继续钻进到总深16. Circulate 15 minutes.循环15分钟17. Run in hole. 下钻18. Put out of hole. 起钻19. Make an inventory of all ring gaskets. 开一个所有垫圈的清单20. Use spinning tong. 使用气动扳手21. Operate the air winch. 操作气动绞车22. Lay down 57 joints of 5”drill pipe. 甩57根钻杆23. Pick up drill stem test tool. 提起钻杆测试工具24. Circulate mud for 2 hours. 循环泥浆2小时25. Move string during circulation. 在循环时注意活动钻具26. Circulate hole clean. 循环清洗井眼27. Circulate bottoms up. 循环泥浆几周28. Fill up every 5 stands. 每5柱灌泥浆一次29. Check mud weight every 15 minutes. 每15分钟检查泥浆比重30. Reverse out excess cement. 反循环替出多余的泥浆31. Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆32. Stop drilling. 停止钻进33. Drilling ahead. 钻进34. Pull out of hole bit. 起出钻头35. Change bit. 换钻头36. Run the wear bushing. 下抗磨补心37. The bit thread type is regular pin. 钻头丝扣是正规公扣38. What’s the make-up torque? 上扣扭矩要多大?39. Run in 9”collars. 下9”钻铤40. The cathead can’t give enough torque. 猫头力量不够41. Connect crossover sub. 接上配合接头42. The tong angle is too small. 大钳的角度太小了43. Stop circulating. 停止循环泥浆44. Break out the stand. 卸立柱45. Set the single into the mousehole. 把这个单根放进鼠洞46. Can we break out the pipe with rotary table? 可用转盘卸扣吗?47. No! Break it out with tong. 不行! 要用大钳卸扣48. Spin it out with the air spanner. 用气动扳手卸扣49. Put the pipe wiper on the string. 装上钻杆刮泥器50. Don’t set this stand back. 这根钻杆不要放在钻杆盒上51. Make up the lift sub. 接好提升短节52. Secure the safety clamp. 上紧安全卡瓦53. The bit is nearing the shoe. 钻头快到套管鞋了54. Slow down the running speed. 放慢下放速度55. This is the undergauged interval. 这是缩径井段56. This is the drilling program. 这是钻井设计书57. How much weight on bit is required? 要加多少钻压?58. Keep the rotary speed at 120---140 RPM. 转速保持120---140转/分59. Keep the flow rate at 3000 LPM. 保持排量3000升/分60. The pump pressure is too high. 泵压太高了61. Don’t ream the hole too fast. 划眼不要太快62. Notice the rotary torque. 注意转盘扭矩的变化63. The penetration rate is getting slower. 钻速变慢了64. The bit is nearly worn out. 钻头快磨光了65. Stop drilling at 2000 meters. 钻至2000米停钻66. Circulate for one hour. 循环一个小时67. The pump pressure has increased. 泵压升高了68. One nozzle may be plugged. 可能有一个水眼(或: 喷嘴)堵了69. What is the hook load? 悬重多少?70. What’s the pick-up weight? 上提重量是多少?71. What’s the lowering weight? 下放重量是多少?72. Run in HWDP. 下加重钻杆73. A stabilizer is needed here. 这里需要一个扶正器74. This is a flexible sub. 这是挠性接头75. This is the BHA log. 这是下部钻具组合记录76. Record all outside and inside diameters. 记录好所有(入井工具的)内外径77. We need a short drill collar. 需要一根短钻铤78. Pull the cat line. 拉猫头79. Operate the break lever. 操作(或:扶)刹把80. Stop the pumps. 停泵81. Make a wiper trip. 通井82. Retrieve wear bushing. 取出抗磨补心83. Bleed off pressure. (释)放压(力)84. Keep 5 wraps on the drum. 滚筒上留5圈85. Set slips. 座上卡瓦86. If tight hole, repeat wiper trip. 如果井眼紧, 重复划眼87. Setback bottom hole assembly. 将下部钻具立于钻杆盒内88. Make sure all alarms are on. 确保所有的警报信号都开着89. Lay down TDS spinner. 拆下顶部驱动的旋扣器90. Run in hole bit #15 to bottom. 用15号钻头下钻到井底91. Run in hole to casing shoe. 下钻至套管鞋92. Pick up same bit and BHA. 装上同样的钻头和钻具组合93. Lay down 5”HW drill pipe. 甩5”加重钻杆94. Move string every 2 hours. 每2小时活动钻具一次95. Keep area around shaker clean. 保持振动筛区域干净96. Control trip gas. 控制起下钻气97. Ream if needed. 如必要时进行划眼98. Select the best penetration rate. 选择最佳钻进速度99. Fix the traveling assembly. 固定游动系统100. Check power tongs and spinning rope are on drill floor. 检查动力钳和尾绳是否在钻台100. What’s the weight on bit? 钻压是多少?101. What is the BHA of this well? 这口井的下部钻具如何组合?102. Drill out cement. 钻穿水泥103. Drill out 20”casing shoe. 钻穿20”套管鞋104. Latch the elevator. 扣吊卡105. Unlatch the elevator. 开吊卡106. Set the slips. 放卡瓦107. Adjust the crown-o-matic (crown saver). 调整防碰天车108. Lock the hook pin. 锁紧大钩销子109. Check OD of stabilizer. 检查扶正器的外径110. Perform leak off test. 进行地层破裂(或:渗漏)测试111. Connect kill and choke line. 接上压井和放喷管线112. Reverse out the drill pipe. 反循环清洗钻杆113. Make a short trip. 进行短途起下钻114. Change the cutters. 换割刀115. Slug the pipe. 灌重泥浆116. Drill the stand down. 钻完立柱117. Start/run the shale shaker. 开振动筛118. Start the desanders. 开除砂器119. Start the desilters. 开除泥器120. Change it with a 40 mesh screen. 换成40目筛布121. Shut it off. 关掉122. Pull it to the cat ramp. 把它拉到坡道上去123. Make a fast connection. 接单根要快124. Don’t dump the mud into the sea. 不要把泥浆排放到海里125. Disconnect it with a chain tong. 用链钳卸开126. Put a thread protector. 加一个(丝扣)护箍127. Can we use the power slips? 可以使用动力卡瓦吗?Casing and Cementing 下套管与固井128. Run in hole to bottom for wiper trip. 下钻通井129. This is the casing program. 这是套管程序130. Prepare for running casing. 准备下套管131. Make everything ready for running 7”casing. 做好下7”套管的准备132. Make cementing job. 固井133. Displace cementing with mud pump. 用泥浆泵替泥浆134. Set cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞135. Pick up cementing head. 接水泥头136. Cement samples are hard. 水泥样已凝固137. Pump in 3 cubic meters of spacer. 注3方隔离液138. Pump down the plug. 泵压(胶)塞139. Wait on cement. 候凝140. The guide shoe will be connected. 接引鞋141. Connect the floor collar. 接浮箍142. Connect the air line to the casing stabbing board. 接好套管扶正台的气管线143. Run casing with the 350T slip elevator. 用350吨卡瓦式吊卡下套管144. Clean and dry 20”casing threads with rags. 清洁并擦干20”套管丝扣145. Where is the rabbit for drifting the casing? 套管通径规在哪里?Rig Move, Anchoring and Positioning 拖航, 抛锚, 定位146. What is our position now? 我们现在船位在哪里?147. What’s the moving speed now? (What’s the towering speed?) 拖航速度是多少?148. The speed is about 4 knots. 船速是4节左右149. Which one is the main tug? 主拖是哪条船?150. The main tug is Nanhai 205. 主拖是南海205151. Which one is the chase boat? 护航船是哪一条?152. How much is the horse power? 有多大马力?153. She has 6000 HP. 有6000马力154. Move the rig off location 50 feet. 将平台移开50英尺155. We are ready to drop the anchor. 我们已经做好抛锚的准备了156. Secure all the movable equipment. 固定好各种活动的设备157. Preload. (自升式)压载158. Ballast. (半潜式)压载159. Put the preload water into the tank. 向压载舱灌压压载水160. We need 5500 tons of preload water. 需要5500吨压载水161. Shall we preload right now? 马上开始压载吗?162. Drain the water off. 放水163. The rig is overloaded. 平台已超载164. Jack up (jack down) the rig. 升(降)船165. The draft is 3.5 meters. 船体吃水3.5米166. The jetting pressure is 100psi. 冲桩压力是100psi167. Penetrate the legs. 插桩168. How much penetration do we have? 入泥多深了?169. No.1 and No.2 legs indicate 10 meters. 1,2号桩腿插入10米170. Fix the upper and lower wedges. 固定上下楔块171. Pay out the anchor line. 放出锚缆绳172. Skid the derrick. 移开井架173. The rig is short of potable water now. 平台缺乏饮用水174. Drop No.2 and No.3 anchors. 抛2号和3号锚175. Why has the main engine stopped? 主机为什么停?176. Unleash the drilling tools. 卸开钻具177. Tighten up. 绷紧(或:上紧)一点178. Turn on the cooling water for the windlasses. 开锚机刹车冷却水179. Retrieve the No.1 to No.8 anchors. 起1到8号锚180. Check the paint marks at the anchor winches. 检查锚机上的油漆记号181. Prepare for a location move. 准备好移井位182. Commence anchor handling. 开始起锚(或抛锚)183. Secure all equipment stored on deck. 固定好所有存放在甲板上的设备184. Carry out stability and load calculations. 做稳性和载荷计算185. Pass pendant line, shackle and buoy to anchor handling vessel. 将起抛锚短索,卸扣和浮标吊起给起锚船186. Lower the windward anchor to seafloor. 抛上风锚到海底187. Pick up the leeward anchor first. 先起下风锚188. Take anchor chaser (or chaser) back to rig. 将捞/抛锚环送回平台189. Hook up towing lines to tug boat. 将拖缆连接到拖轮190. Sound fog signal for two seconds every twenty seconds. 发大雾信号, 每20秒钟响两秒Fishing 打捞191. The bit cutters have been lost in the hole. 牙轮落井192. Run in the reverse-circulation basket. 下反循环打捞篮193. There is a lot of junk in the hole. 井下有很多落物194. The fish is 235.46 meters long. 落鱼长度235.46米195. The fish top is at 2478.34 meters. 鱼顶位置2478.34米Coring 取芯196. Stop drilling for coring. 停钻准备取芯197. Make up core bit. 接取芯钻头198. What type of core bit is it? 这是什么型号的取芯钻头?199. Run in a diamond core bit. 下金刚石取芯钻头200. Let’s drop the ball for coring. 可以投球取芯201. The core has been broken off. 岩芯断了202. Put the core in the boxes. 把岩芯装在岩芯盒里203. Don’t brake suddenly. 不要猛刹车204. Take out the core. 岩芯出筒205. How long is the core? 岩芯多长206. The core recovery is 98%. 岩芯收获率是98%207. Run in the core barrel again. 继续下岩芯筒(或: 取芯筒)208. Run in hole core barrel. 下取芯筒209. Drop ball. 投钢球210. Recover core. 取出岩芯211. Use same parameters as for core #1. 使用与1#取芯同样的参数Freeing Stuck Pipe 卡钻与解卡212. The down-hole problems are very complicated. 井下情况很复杂213. The hole is tight. 遇阻了214. Overpull while tripping out. 起钻遇卡(overpull: 超拉力) 215. The formation is unstable. 地层不稳定216. The wall caving is severe. 井壁垮塌严重217. There are many return cuttings. 返出岩屑特别多218. The mud returns have decreased. 返出泥浆减少219. The hole is enlarged. 井眼扩大了220. The pipe’s stuck. 卡钻了221. Pull up to 150 tons. 上提150吨222. Slack off to 50 tons. 下放至50吨223. Ream down all the tight points. 在所有遇阻点进行划眼224. The rotary table can’t rotate. 转盘转不动225. Where is the sticking point? 卡点在哪里226. Make a tensile test. 做拉伸试验227. Back it off above the free point. 在卡点以上倒扣228. Where is the back-off position? 脱扣位置在哪229. Plug the well for side tracking. 打水泥塞侧钻Abnormal Well Condition and Well Control异常井况与压井230. The mud is gas out. 泥浆有气侵231. The pit has lowered quickly. 泥浆池液面下降很快232. The hole lost returns. 井口不返泥浆233. The returns are unstable. 返出泥浆量忽大忽小234. Where’s the thief zone? 漏失层在哪里235. Cut down the flow rate. 降低排量236. Lower the mud density. 降低比重237. Cut down the hydrostatic pressure. 减少静压238. The gas smell is strong. 天然气味度很浓239. There’s some trace of oil. 发现有油花240. The pump pressure is fluctuating. 泵压不稳241. It is a zone of abnormal pressure. 这是异常压力层242. The hole (well) is kicking! 井涌啦!243. Shut in the BOP! 关闭防喷器244. Sound the general alarm quickly! 快发出综合警报245. The stand pipe pressure is 10 kg/cm2. 立管压力10公斤/厘米2246. The casing pressure is 25 kg/cm2. 套压2510公斤/厘米2247. Fill out the kill sheet. 填写压井记录表248. Kill the well. 压井249. There’s a combination of lost returns and the kick. 又喷又漏, 情况复杂250. Reverse the gas out of the hole. 反循环排气251. What’s the lag time? 迟到时间是多少252. The well is now stable. 现在井眼已经稳定BOP and subsea Equipment 防喷器与水下设备253. Cut off the 30”conductor. 割掉30”隔水管254. Weld on the 30”bottom flange. 焊接30”法兰255. Hoist and nipple up 30”diverter. 吊装30”转喷器256. Change the 5”pipe rams to 3-1/2”rams. 把这个5”闸板换成3-1/2”257. Install blind ram. 安装防喷器的盲板芯子258. Check the seal ring of the conductor. 检查隔水管密封圈259. Cut off the lifting eye of the conductor. 切割隔水管耳环260. Test BOP. 测试防喷器261. Change annular BOP packing. 更换万能防喷器芯子262. Full pressure test the ram preventers. 对闸板防喷器进行全压试压263. Test annular BOP at 2500psi. 万能防喷器试压至2500psi264. Check annular pressure. 检查环形空间压力265. Confirm the angle of the guide base. 确定基板角度266. The thread is covered with the quick-release protectors. 已戴好快卸护丝267. Establish the guide lines. 装导向绳268. Connect the TGB running tool. 接临时导向基板送入工具269. Land the TGB to sea. 下临时导向基板到海底270. Retrieve the running tool. 退出送入工具271. Run the BOP and risers. 下防喷器和隔水管272. Pick up the marine riser. 吊出隔水管273. Pick up the slip joint. 起伸缩节274. Adjust the riser tensioners. 调整隔水管张力275. Function test the diverter system. 对防喷器系统进行功能测试276. Retrieve the pin connector. 取出销钉连接器277. Move the BOP to the moonpool door. 将防喷器移到园井甲板的活动门上278. Run the test plug. 下试压塞279. Close the upper pipe ram. 关上部钻杆闸板防喷器280. Open the kill line valve. 开压井管线阀281. The compensation capacity is 400000 pounds. 补偿能力是400千磅282. The locking load is 1000000 pounds. 锁紧负荷1000千磅283. Support the riser. 接隔水管支撑环284. Remove the hose bundles. 卸下垮接软管285. Assure the self-controlled rotation. 保证自控转动286. Set the LMRP on the test pump. 将下部防喷器插入总成座放到试压桩上287. Connect the flex joint to the riser. 连接隔水管与挠性接头288. Land the BOP onto the well head. 座防喷器到井口头289. Run the subsea TV for monitoring. 下水下电视观察290. Remove all the riser running tools. 取出所有的隔水管送入工具291. BOP carrier. 防喷器叉车292. Lower the universal guide frame. 下放万能导向架293. Paint mark the top 6 meters of 30”conductor white. 在30”隔水管的顶部6米处用白漆涂上记号294. Check adequate length for guidelines. 检查导向绳的长度是否足够295. Move temporary guide base (TGB) into moonpool. 将临时导向基板到园井甲板296. Test pull to check connection. 试拉检查连接297. Grease TGB and running tool as required. 按要求给导向基板及下入工具上黄油298. Test fit TGB and running tool. 用下入工具试临时导向基板连接299. Check for junk inside shoe joint. 检查浮鞋内有无落物300. Pick up 30”conductor handling slings and shackles. 吊上下30”导管的索具和卸扣301. Is slope indicator properly mounted? 水平仪是否装好?302. Ensure subsea TV is in good condition. 确保水下电视处于良好的状态303. Place BOP stack on the test pump. 将防喷器组放在试压桩上304. Check condition of all 30”casing connectors. 检查所有30”套管接头的情况305. Replace O-rings as required. 按需要, 更换O性密封圈306. Attach slope indicator below camera position. 在摄像机下面装上水平仪307. Inspect and repair diverter. 检查并修理转喷器308. Prepare spud plate and wireline to check water depth. 准备测深板和钢丝绳测量水深309. Record all pressure tests on a chart recorder. 用试压表记录试压记录310. Visually inspect all sealing element. 目视检查所有密封件311. Check and tighten all bolts. 检查并上紧所有螺栓312. Bleed off surface accumulators. 地面管线排空气313. Check for leaks. 检查有无泄漏314. Lift BOP stack and replace wellhead connector AX ring. 吊起防喷器组并更换连接器AX密封圈315. Function test wellhead. 对井口头进行功能试验316. Fill kill and choke valves with seawater. 将压井阀和阻流阀注满海水317. Pressure test to 500psi then bleed off test pressure. 试压到500psi, 然后放掉压力318. Reduce hydraulic control manifold pressure to 5200 kpa. 将液压控制管线压力减少到5200千帕319. Switch to alternate control pod. 把闸门开关倒到控制面板320. Guidelines are slacked off. 导向绳松了321. Slack off drill pipe and release running tool. 放松钻杆并卸开下入工具322. Run subsea TV to observe bit entering the TGB. 下水电视观察钻头是否进入临时导向基板323. Don’t rotate until hole opener passes through the TGB. 在扩眼器通过临时导向基板前不要旋转324. Position permanent guide base (PGB) below rotary table. 在转盘下安放永久导向基板325. Monitor riser level via trip tank. 用计量罐来控制隔水管内的液面326. Pressure test to 5000psi. 试压5000psi327. Pick up test mandril and place in BOP. 吊起试压防喷器芯子并装入防喷器组328. Safety and Firefighting 安全与消防328. Get a Work Permit before you can start the hot work. 办理作业许可证才能进行动火作业329. Welding is not allowed. 不准动焊330. Put on your (safety) helmet. 戴上安全帽331. It’s a high voltage area. 这是高压区332. That’s against the rule. 这是违章作业333. Don’t walk under the crane load. 不要在吊物下走动334. The repairing is under way. 正在检修335. Keep your hands clear! (Keep you hands off! Do not touch!) 不要乱动336. Wear and secure your safety belt. 戴上并系好安全带337. Life jacket must be worn when working outboard or overhead. 舷外或高空作业要穿救生衣338. Have your breathing apparatus near you. 保持放毒面具在附近339. It’s a drill. 这是演习340. It was a BOP drill. 这是防喷演习341. Get in the lifeboat in order. 按顺序进入救生艇342. Put on life jacket! 穿好救生衣343. Abandon the vessel! 弃船344. Sound the abandonment alarm! 发出弃船警报345. Go to the helideck! 去飞机坪集合346. Aboard the lifeboat. 登上救生艇347. Aboard the supply boat to shore! 乘拖船上岸348. Check life saving apparatus periodically. 定期检查救生设备349. It’s for fire fighting. 这是消防用的350. Start the fire pump. 启动消防泵351. This rope is too small. 这根绳子太细了352. It should be function tested. 需做功能测试353. A warning notice should be set up. 要挂警告牌354. Do you have an emergency program (contingency plan)? 你们有没有应急计划?355. It must be ready in an emergency condition. 必须始终保持良好的应急状态356. Will the typhoon hit our rig? 台风要袭击我们的平台吗?357. We will have to evacuate the rig. 我们要撤离平台358. Personnel on board (POB). 在船人员总数359. Sound fire alarm. 发消防警报360. This is a fire drill. 这是消防演习361. conduct abandon ship drill. 举行弃船演习362. Release the boat hooks. 释放救生艇吊钩363. Board the life boat. 登救生艇364. Remove the rust and paint with anti-corrosive primer. 除锈后上防锈底漆365. Three rafts are located near life boat station port side. 在左舷救生艇站附近还存放有3个救生筏366. Wear work vests when working below the cellar deck. 在圆井甲板面下面工作时须穿工作救生衣367. The station bills need to be updated. 应急部署表须更新368. Check the expiry date for all foam extinguisher. 检查所有泡沫灭火器的过期时间369. Close all the water-tight doors. 关闭所有水密门370. Safety procedure shall be followed at all the times. 在任何时候都应遵守安全程序371. Anchor wires should have a Spelter type socket at anchor side. 抛锚绳靠锚的一端应使用锌压头372. Colour code all the connection at the loading station. 在供给站管线接头处用颜色表明各管线373. Verify that a high level alarm is installed on the sludge tank. 确认污水舱安装有高位警报374. Don’t switch on during drilling operation. 钻井作业期间不能合闸375. Provide two independent means to start the emergency generator engine. 应急发电机柴油机应有两套独立的起动方法376. Have the boom pennant wires of port crane re-certified. 重新认证左舷吊车扒杆变幅绳377. Clean the internals of the emergency switchboard. 清洁应急配电盘内部Helicopter and Supply Vessel 直升机与供应船378. Load out Contractor’s riser at Zhanjiang anchorage. 在湛江锚地把承包商的隔水管装上平台379. Offload casing. (从供应船上)卸套管380. Load (offload or unload) the boat. 装(卸)船381. Get the food container loaded on the boat. 把食品集装箱装上船382. The helicopter will land on rig soon. 直升机很快就要在平台降落383. Tell the base to get (or send) a chopper here. 通知基地派飞机来384. Helicopters are not allowed to land here. 飞机不能降落385. Report the weather condition to the pilot. 向飞行员报天气386. Inform the boat come to standby. 通知拖轮过来待命387. Call the boat to come along port side. 通知拖轮过来靠左舷388. We will take the personnel basket. 我们乘坐吊篮Repair and Maintenance 检修389. Have an overall check. 进行全面检查390. MPI the brake linkage system. 对刹车连接系统进行磁粉探伤391. Demonstrate that the make-up cathead can pull 7000 lbs. 证明上扣猫头能拉到7000磅392. Determine the origin of the air leak and rectify this. 找出漏气的地方并处理393. Adjust the brake band equalizer beam properly. 适当调整刹带平衡梁394. Note that the 3000 hour inspection on TDS is due. 注意顶驱的3000小时保养时间已到395. Check sheave rope pocket wear with a 1 3/8”+1 1/32 template. 用1 3/8”+1/32”量规检查绳槽磨损的情况396. Repair the handrails on the crown. 修理天车台的栏杆397. Function test the anti-freefall brake on monthly basis. 每月对天车防碰装置进行功能试验398. Get me a spanner, please. 请递给我一把扳手399. Renew brake rim because of excessive wear. 更换磨损严重的刹车鼓400. Clearly mark safe working load (SWL) on the air winch below the rig floor. 表明钻台底下气动绞车的安全工作负荷401. Measure the master bushings for wear. 测量主补心磨损情况402. Have BOP ram opened up for internal inspection. 打开防喷器闸板进行内部检查403. Install a ground cable on the triplex pump motor. 给三缸泵马达安装接地线404. We need a 48”pipe wrench. 我们需要一把48”的管钳405. Strike it with a sledge hammer. 用大锤打406. We want a triangle file. 需要一把三角锉刀407. Tighten up the screw. 紧一下螺丝408. Check it with a level. 用水平尺量一下409. Put some engine oil. 抹点黄油410. Have it greased. 给它上黄油411. Put out of hole test string. 取出测试管串412. Check all the equipment. 检查所有设备413. There’s something wrong with it. 有点毛病414. Rig inspection will be performed in August. 验船安排在8月份415. Maintain the hoisting system. 保养提升系统416. Adjust the brake band. 调整绞车刹带417. Change the oil in the rotary gear box (transmission). 更换转盘变速箱机油418. Replace one water pump. 倒换一台冷却泵419. It’s quick-discharge air valve. 这是快速放气阀420. This clutch needs repair. 这台离合器需修理421. This tong needs replacing. 这把钳要更换了422. Slip 6 meters of the drilling line. 滑移钻井大绳6米423. Cut off 45 meters of the drilling line. 切割大绳45米424. Check the pump liners and pistons. 检查(泥浆)泵缸套和活塞425. The piston has been washed. 活塞刺坏了426. The supercharge pump doesn’t take in water. 灌注泵不上水427. Regulate the relief valve. 调整安全阀428. This part number is wrong. 这个配件号不对429. The multi-pen recorder has some problem. 多笔记录仪坏了Miscellaneous 其他430. No smoking here. 此处严禁吸烟431. Everything is OK. 一切准备就绪432. Speed up please. 请快点433. The geologist must be present. 地质人员必须到场434. We have to wait on weather. 必须等候天气435. There will be strong wind. 有强风436. Give me a hand, please. 请帮一下忙437. Do you understand? 明白吗?438. No way! 不行439. Man overboard! 有人落水440. Help! Help! 救命441. Someone is injured. Medic! 有人受伤了, 医生442. Call for the medic. 叫医生443. Get a stretcher please. 拿担架来444. No more than 4 persons. 不能超过4人445. Drinking liquor is not allowed. 不许喝酒446. Don’t overrun your equipment. 不要超负荷运转447. Be careful at work. 工作时要小心448. No joking here. 别开玩笑449. Rig up for logging. 准备电测450. What is the next step? 下一步怎么办?451. Get everything ready as soon as possible! 尽快做好一切准备附录一: 平台人员岗位名称一. 承包商人员( Contractor’s Personnel ) Rig Manager 平台经理Equipment Supervisor 设备总监Materials Supervisor 材料总监Senior Toolpusher 高级队长Junior Toolpusher 值班队长Driller 司钻Sub Sea Engineer (SSE) 水下工程师Assistant Driller (AD) 副司钻Derrick Man 井架工Floor Man (roughneck) 钻工Barge Master (captain) 船长First Mate (Barge engineer) 大副Control Room Operator (CRO) 压载工Ballast Control Operator (BCO) 压载工Chief Engineer 轮机长Head of Routabout 甲板班长Crane Operator 吊车工Routabout 甲板工Mechanic 机械师Electrician 电气师Repairman 修理工Motorman 轮机员Welder 焊工Radio Operator 电报员Warehouse Man (stock Keeper) 材料员Medic 医生Safety Supervisor 安全监督Interpreter (translator) 翻译Chief Steward 管事Cook 厨师Steward 厨工Laundry Man 洗衣工二. 作业者及服务公司人员( Operator’s Personnel and Service Company Personnel) Drilling Superintendent 钻井监督Company Man (Operator’s Representative) 公司代表Geologist 地质师Mud Logging Engineer (Mud logger) 泥浆录井工程师Sample Catcher 捞砂工Mud Engineer 泥浆工程师ROV Engineer 潜水工程师Cementer 固井工Cement Engineer 固井工程师Testing Engineer 试油工程师Coring Engineer 取芯工程师Wireline Logging Engineer电测工程师附录二: 平台主要设备一. 钻井设备(Drilling Equipment):Drawworks 钻井绞车Rotary Table 转盘Bushing 补心Top Drive System (TDS) 顶驱Swivel 水龙头Crown Block 天车Traveling Block 游车Hook 大钩Derrick 井架Pipe Spinning Wrench 钻杆气动扳手Ezy-Torq 液压猫头Elmagco Brake 涡磁刹车Pipe handling Equipment 钻杆移动设备Iron roughneck 铁钻工Pipe Racking System 钻杆排放系统Drill String 钻柱Drilling Sub 钻井短节Fishing Tool 打捞工具Power Tong 动力大钳Air Winch (air tugger) 气动绞车Crown-O-Matic (Crown Saver) 防碰天车二. 泥浆系统(Mud System)Mud Pump 泥浆泵Shale shaker 振动筛Mud Cleaner 泥浆清洁器Desilter 除泥器Desander 除砂器Degasser 除气器Centrifuge 离心机Mud Agitator 泥浆搅拌器Mud Mixing System 泥浆混合系统Centrifugal Pump 离心泵Standpipe Manifold 立管管汇Rotary Hose 水龙带Bulk Air System and Tank 吹灰系统和灰罐三. 井控设备(Well Control Equipment):Ram Type Preventor 闸板防喷器Annular Type Preventor 万能防喷器BOP Stack 防喷器组Gate Valve 闸阀Choke and Kill Manifold 阻流压井管汇Remotely Operated Panel 远程控制面板Choke Control Panel 阻流控制面板BOP Handling Equipment 防喷器搬运设备Diverter 转喷器四. 海事系统(Marine System)Ballast System 压载系统Bilge System 污水系统Vent 通风口, 通气口Air Supply Fan 供气扇Mooring System 锚泊系统Communication Equipment 通讯系统Jacking System 升降系统Skidding System 井架滑移系统Windlass 锚机Anchor 锚Pendant 短索Buoy 浮标Lifting and Handling Equipment 起吊和搬运设备五. 机房(Engine Room)Diesel Engine 柴油机Emergency Generator 应急发电机Water Maker (desalinization unit) 造淡机Air Compressor 空气压缩机Boiler 锅炉Air-conditioning System 空调系统Sea Water Service Pump 海水供给系统Piping System 管汇系统Generator 发电机Transformer 变压器DC Motor 直流马达AC Motor 交流马达六. 安全设备(Safety Equipment)Fire Control System 消防控制系统Fire Detection System 火情探测系统CO2 System 二氧化碳系统Fixed Fire Extinguishing System 固定消防系统Portable Extinguisher 移动灭火器Fire-Fight Equipment 消防设备Foam System 泡沫系统Lifeboat 救生艇(Inflatable) Life Raft (气涨式)救生筏Davit 吊艇架Escape Routes 逃生路线Breathing Apparatus 呼吸器Life Buoy 救生圈Gas Detection System 气体探测系统Helicopter Facility 直升机设施Sick-Bay (Hospital) 医务室Pollution Control 防污控制七. 其他( Others)Cementing Unit 固井装置Well Testing Equipment 试油设备Mud Logging Unit 泥浆录井房Wire Logging Unit 电测装置ROV 潜水器Meter 米Foot 英尺Inch 英寸Supply Boat (supply vessel) 供应船Standby boat 值班船Day (night) Shift 白(夜)班Crew Change 倒班Crew 船员, 队员, 井队Position 岗位Draft (draught) 吃水Air Gap 空气间隙, 气隙Penetration (桩腿插桩)入泥Evacuation 撤离Rig (Drilling rig) 钻机, 钻井船附录三. 平台场所Bow 船首Stern 船尾Forward (FWD) or fore 船首的Aft 船尾的Port 左舷Starboard (STBD) 右舷Upper Deck 上部甲板Main Deck 主甲板Quarters (living quarters, accommodation area) 生活区Drill Floor (Rig floor) 钻台Bridge (Pilot house, Steerwheel house) 驾驶室Control Room 控制室Helideck 直升机甲板Cementing Unit Room 固井泵房Air Compressor Room 空气压缩机房BOP Control Room BOP控制房Radio Room 报房Engine Room 机房Thruster Room 推进器房Warehouse (Store) 材料库房Paint Room (paint locker) 油漆房库Leg 桩腿Jacking House 升降室Column 立柱Sack Storage Area 散装材料储存区Mud pit 泥浆池Cellar Deck 圆井甲板Riser Rack Area 隔水管排放区Pipe Rack Area 钻杆排放区Pipe Slide 滑道Ramp 坡道Spud Tank 桩脚箱Pontoon 浮箱Moonpool 月池/园井甲板Pump Room 泵房Shale Shaker House 振动筛房Coffee Room 咖啡室Rig Office 平台办公室Mess (dining) Room 餐厅Recreation Room 娱乐房TV RoomChange Room 工衣房Kitchen 厨房附录四. 钻具,井口工具,打捞工具Drill Pipe 钻杆Drill Collar 钻铤Heavy Weight Drill Pipe 加重钻杆Elevator 吊卡Tong 大钳Make-up Tong 上扣大钳Break-out Tong 卸扣大钳Mud Box 泥浆防喷盒Casing Stabbing Board 套管扶正器Slips 卡瓦Spider 卡盘Mouse Hole 小鼠洞(接单根用) Kelly Spinner 方钻杆旋转器Kelly Cock 方钻杆阀Chain Tong 链钳Casing 套管Tubing 油管Drill String 钻柱Jar (drilling jar) 震击器Right Hand Thread 正扣Left Hand Thread 反扣Stabilizer 扶正器Rabit 通管器Liner 尾管Conductor 导管Thread Protector 护丝Stand (钻杆) 立柱Single (钻杆) 单根Joint (钻具) 根Bend 弯头Sub 短节Pup Joint 短钻杆, 短节Connector 接头Bit 钻头Bit Breaker 钻头盒Box 母扣Pin 公扣Hole Opener 开眼钻头Reamer 扩眼钻头Overshot 打捞筒Junk Basket 打捞篮Junk Mill 平头磨鞋Spear 打捞矛Fishing Tap 打捞公锥Cross Over Sub (XO Sub) 转换接头Bottom Hole Assembly (BHA) 下部钻具组合附录五. 材料和工具Steel 钢Iron 铁Wood 木Chemicals 化学品Cement 水泥Barite 重晶石Potable Water 淡水Drilling Water 钻井水Sea Water 海水Fuel 柴油Helifuel 飞机燃油Lubricant (Lube/Lube oil) 润滑油Grease 黄油Thread Dope 丝扣油Ballast Water 压载水Bilge Water 舱底水Gasoline 汽油Mud 泥浆Bentonite 般土Additive 添加剂Caustic Soda 烧碱Weight Material 加重材料Thinner 稀释剂Oxygen 氧气Nitrogen 痰气Hydrogen Sulphide 二氧化硫Acetylene 乙炔Compressed Air 压缩空气Hydraulic Fluid 液压油Spanner 扳手。
钻井常用英语手册
A Handbook of English for Offshore Oil Drilling海洋石油钻井常用英语手册附录一: 平台人员岗位名称一. 承包商人员( Contractor’s Personnel )Rig Manager 平台经理Equipment Supervisor 设备总监Materials Supervisor 材料总监Senior Toolpusher 高级队长Junior Toolpusher 值班队长Driller 司钻Sub Sea Engineer (SSE) 水下工程师Assistant Driller (AD) 副司钻Derrick Man 井架工Floor Man (roughneck) 钻工Barge Master (captain) 船长First Mate (Barge engineer) 大副Control Room Operator (CRO) 压载工Ballast Control Operator (BCO) 压载工Chief Engineer 轮机长Head of Routabout 甲板班长Crane Operator 吊车工Routabout 甲板工Mechanic 机械师Electrician 电气师Repairman 修理工Motorman 轮机员Welder 焊工Radio Operator 电报员Warehouse Man (stock Keeper) 材料员Medic 医生Safety Supervisor 安全监督Interpreter (translator) 翻译Chief Steward 管事Cook 厨师Steward 厨工Laundry Man 洗衣工二. 作业者及服务公司人员( Operator’s Personnel and Service Company Personnel) Drilling Superintendent 钻井监督Company Man (Operator’s Representative) 公司代表Geologist 地质师Mud Logging Engineer (Mud logger) 泥浆录井工程师Sample Catcher 捞砂工Mud Engineer 泥浆工程师ROV Engineer 潜水工程师Cementer 固井工Cement Engineer 固井工程师Testing Engineer 试油工程师Coring Engineer 取芯工程师Wireline Logging Engineer电测工程师附录二: 平台主要设备一. 钻井设备(Drilling Equipment): Drawworks 钻井绞车Rotary Table 转盘Bushing 补心Top Drive System (TDS) 顶驱Swivel 水龙头Crown Block 天车Traveling Block 游车Hook 大钩Derrick 井架Pipe Spinning Wrench 钻杆气动扳手Ezy-Torq 液压猫头Elmagco Brake 涡磁刹车Pipe handling Equipment 钻杆移动设备Iron roughneck 铁钻工Pipe Racking System 钻杆排放系统Drill String 钻柱Drilling Sub 钻井短节Fishing Tool 打捞工具Power Tong 动力大钳Air Winch (air tugger) 气动绞车Crown-O-Matic (Crown Saver) 防碰天车二. 泥浆系统(Mud System)Mud Pump 泥浆泵Shale shaker 振动筛Mud Cleaner 泥浆清洁器Desilter 除泥器Desander 除砂器Degasser 除气器Centrifuge 离心机Mud Agitator 泥浆搅拌器Mud Mixing System 泥浆混合系统Centrifugal Pump 离心泵Standpipe Manifold 立管管汇Rotary Hose 水龙带Bulk Air System and Tank 吹灰系统和灰罐三. 井控设备(Well Control Equipment): Ram Type Preventor 闸板防喷器Annular Type Preventor 万能防喷器BOP Stack 防喷器组Gate Valve 闸阀Choke and Kill Manifold 阻流压井管汇Remotely Operated Panel 远程控制面板Choke Control Panel 阻流控制面板BOP Handling Equipment 防喷器搬运设备Diverter 转喷器四. 海事系统(Marine System)Ballast System 压载系统Bilge System 污水系统Vent 通风口, 通气口Air Supply Fan 供气扇Mooring System 锚泊系统Communication Equipment 通讯系统Jacking System 升降系统Skidding System 井架滑移系统Windlass 锚机Anchor 锚Pendant 短索Buoy 浮标Lifting and Handling Equipment 起吊和搬运设备五. 机房(Engine Room)Diesel Engine 柴油机Emergency Generator 应急发电机Water Maker (desalinization unit) 造淡机Air Compressor 空气压缩机Boiler 锅炉Air-conditioning System 空调系统Sea Water Service Pump 海水供给系统Piping System 管汇系统Generator 发电机Transformer 变压器DC Motor 直流马达AC Motor 交流马达六. 安全设备(Safety Equipment)Fire Control System 消防控制系统Fire Detection System 火情探测系统CO2 System 二氧化碳系统Fixed Fire Extinguishing System 固定消防系统Portable Extinguisher 移动灭火器Fire-Fight Equipment 消防设备Foam System 泡沫系统Lifeboat 救生艇(Inflatable) Life Raft (气涨式)救生筏Davit 吊艇架Escape Routes 逃生路线Breathing Apparatus 呼吸器Life Buoy 救生圈Gas Detection System 气体探测系统Helicopter Facility 直升机设施Sick-Bay (Hospital) 医务室Pollution Control 防污控制七. 其他( Others)Cementing Unit 固井装置Well Testing Equipment 试油设备Mud Logging Unit 泥浆录井房Wire Logging Unit 电测装置ROV 潜水器Meter 米Foot 英尺Inch 英寸Supply Boat (supply vessel) 供应船Standby boat 值班船Day (night) Shift 白(夜)班Crew Change 倒班Crew 船员, 队员, 井队Position 岗位Draft (draught) 吃水Air Gap 空气间隙, 气隙Penetration (桩腿插桩)入泥Evacuation 撤离Rig (Drilling rig) 钻机, 钻井船附录三. 平台场所Bow 船首Stern 船尾Forward (FWD) or fore 船首的Aft 船尾的Port 左舷Starboard (STBD) 右舷Upper Deck 上部甲板Main Deck 主甲板Quarters (living quarters, accommodation area) 生活区Drill Floor (Rig floor) 钻台Bridge (Pilot house, Steerwheel house) 驾驶室Control Room 控制室Helideck 直升机甲板Cementing Unit Room 固井泵房Air Compressor Room 空气压缩机房BOP Control Room BOP控制房Radio Room 报房Engine Room 机房Thruster Room 推进器房Warehouse (Store) 材料库房Paint Room (paint locker) 油漆房库Leg 桩腿Jacking House 升降室Column 立柱Sack Storage Area 散装材料储存区Mud pit 泥浆池Cellar Deck 圆井甲板Riser Rack Area 隔水管排放区Pipe Rack Area 钻杆排放区Pipe Slide 滑道Ramp 坡道Spud Tank 桩脚箱Pontoon 浮箱Moonpool 月池/园井甲板Pump Room 泵房Shale Shaker House 振动筛房Coffee Room 咖啡室Rig Office 平台办公室Mess (dining) Room 餐厅Recreation Room 娱乐房TV RoomChange Room 工衣房Kitchen 厨房附录四. 钻具,井口工具,打捞工具Drill Pipe 钻杆Drill Collar 钻铤Heavy Weight Drill Pipe 加重钻杆Elevator 吊卡Tong 大钳Make-up Tong 上扣大钳Break-out Tong 卸扣大钳Mud Box 泥浆防喷盒Casing Stabbing Board 套管扶正器Slips 卡瓦Spider 卡盘Mouse Hole 小鼠洞(接单根用) Kelly Spinner 方钻杆旋转器Kelly Cock 方钻杆阀Chain Tong 链钳Casing 套管Tubing 油管Drill String 钻柱Jar (drilling jar) 震击器Right Hand Thread 正扣Left Hand Thread 反扣Stabilizer 扶正器Rabit 通管器Liner 尾管Conductor 导管Thread Protector 护丝Stand (钻杆) 立柱Single (钻杆) 单根Joint (钻具) 根Bend 弯头Sub 短节Pup Joint 短钻杆, 短节Connector 接头Bit 钻头Bit Breaker 钻头盒Box 母扣Pin 公扣Hole Opener 开眼钻头Reamer 扩眼钻头Overshot 打捞筒Junk Basket 打捞篮Junk Mill 平头磨鞋Spear 打捞矛Fishing Tap 打捞公锥Cross Over Sub (XO Sub) 转换接头Bottom Hole Assembly (BHA) 下部钻具组合附录五. 材料和工具Steel 钢Iron 铁Wood 木Chemicals 化学品Cement 水泥Barite 重晶石Potable Water 淡水Drilling Water 钻井水Sea Water 海水Fuel 柴油Helifuel 飞机燃油Lubricant (Lube/Lube oil) 润滑油Grease 黄油Thread Dope 丝扣油Ballast Water 压载水Bilge Water 舱底水Gasoline 汽油Mud 泥浆Bentonite 般土Additive 添加剂Caustic Soda 烧碱Weight Material 加重材料Thinner 稀释剂Oxygen 氧气Nitrogen 痰气Hydrogen Sulphide 二氧化硫Acetylene 乙炔Compressed Air 压缩空气Hydraulic Fluid 液压油Spanner 扳手Hammer 铁锤Screw Driver 螺丝刀Multimeter 万用表Welding Machine 焊机Bar 撬杠Shackle 卸扣Sling (钢丝) 绳套Container 集装箱附录六. 常用缩写形式BHA: bottom hole assembly 下部钻具组合DP: drill pipe 钻杆DC: drill collar 钻铤HWDP: heavy weight drill pipe 加重钻杆BOP: blowout preventer 防喷器TD: total depth 总深TVD: true vertical depth (定向井的)垂直深度SCR: silicon controlled rectifier 可控硅OD: outside diameter 外径ID: inside diameter 内径BBL: barrel 桶LB: (拉丁语) Libra=pound (重量单位) PSI: pound per square inch 磅/英寸2 GAL: gallon 加仑POOH: pull out of hole 起钻RIH: run in hole 下钻WOW: wait on weather 等候天气WOC: wait on cement 候凝JU: Jackup 自升式(钻井船)SEMI: semi submersible 半潜式(钻井船)RPM: revolution per minute 转速/分钟LPM: liter per minute 升/分钟KN: knot 节(海里/小时)SWL: safe working load 安全工作负荷API: American Petroleum Institute 美国石油协会IADC: international association of drilling contractors 国际钻井承包商协会MPI: magnetic particle inspection 磁粉探伤附录七:常用语Drilling 钻井Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业.Prepared bell nipple. 准备”喇叭口”短节.Make up 2 joints of drill pipe. 接两根钻杆.Break out this connection. 卸开该接头.Run hole opener to sea bed. 下扩眼器到海底Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆.Make up bottom hole assembly. 组合下部钻具Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.Number stands on trip out and trip in. 起下钻时给立柱编号.Pick up BHA and run to seafloor. 将下部钻具下到海底.Pick up stands. 接立柱Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱Drop TOTCO. 投(陶特)测斜仪Fish TOTCO with overshot. 用打捞筒捞起测斜仪Resume drilling to T.D. 继续钻进到总深Circulate 15 minutes.循环15分钟Run in hole. 下钻Put out of hole. 起钻Make an inventory of all ring gaskets. 开一个所有垫圈的清单Use spinning tong. 使用气动扳手Operate the air winch. 操作气动绞车Lay down 57 joints of 5” drill pipe. 甩57根钻杆Pick up drill stem test tool. 提起钻杆测试工具Circulate mud for 2 hours. 循环泥浆2小时Move string during circulation. 在循环时注意活动钻具Circulate hole clean. 循环清洗井眼Circulate bottoms up. 循环泥浆几周Fill up every 5 stands. 每5柱灌泥浆一次Check mud weight every 15 minutes. 每15分钟检查泥浆比重Reverse out excess cement. 反循环替出多余的泥浆Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆Stop drilling. 停止钻进Drilling ahead. 钻进Pull out of hole bit. 起出钻头Change bit. 换钻头Run the wear bushing. 下抗磨补心The bit thread type is regular pin. 钻头丝扣是正规公扣What’s the make-up torque? 上扣扭矩要多大?Run in 9” collars. 下9”钻铤The cathead can’t give enough torque. 猫头力量不够Connect crossover sub. 接上配合接头The tong angle is too small. 大钳的角度太小了Stop circulating. 停止循环泥浆Break out the stand. 卸立柱Set the single into the mousehole. 把这个单根放进鼠洞Can we break out the pipe with rotary table? 可用转盘卸扣吗? No! Break it out with tong. 不行! 要用大钳卸扣Spin it out with the air spanner. 用气动扳手卸扣Put the pipe wiper on the string. 装上钻杆刮泥器Don’t set this stand back. 这根钻杆不要放在钻杆盒上Make up the lift sub. 接好提升短节Secure the safety clamp. 上紧安全卡瓦The bit is nearing the shoe. 钻头快到套管鞋了Slow down the running speed. 放慢下放速度This is the undergauged interval. 这是缩径井段This is the drilling program. 这是钻井设计书How much weight on bit is required? 要加多少钻压?Keep the rotary speed at 120---140 RPM. 转速保持120---140转/分Keep the flow rate at 3000 LPM. 保持排量3000升/分The pump pressure is too high. 泵压太高了Don’t ream the hole too fast. 划眼不要太快Notice the rotary torque. 注意转盘扭矩的变化The penetration rate is getting slower. 钻速变慢了The bit is nearly worn out. 钻头快磨光了Stop drilling at 2000 meters. 钻至2000米停钻Circulate for one hour. 循环一个小时The pump pressure has increased. 泵压升高了One nozzle may be plugged. 可能有一个水眼(或: 喷嘴)堵了What is the hook load? 悬重多少?What’s the pick-up weight? 上提重量是多少?What’s the lowering weight? 下放重量是多少?Run in HWDP. 下加重钻杆A stabilizer is needed here. 这里需要一个扶正器This is a flexible sub. 这是挠性接头This is the BHA log. 这是下部钻具组合记录Record all outside and inside diameters. 记录好所有(入井工具的)内外径We need a short drill collar. 需要一根短钻铤Pull the cat line. 拉猫头Operate the break lever. 操作(或:扶)刹把Stop the pumps. 停泵Make a wiper trip. 通井Retrieve wear bushing. 取出抗磨补心Bleed off pressure. (释)放压(力)Keep 5 wraps on the drum. 滚筒上留5圈Set slips. 座上卡瓦If tight hole, repeat wiper trip. 如果井眼紧, 重复划眼Setback bottom hole assembly. 将下部钻具立于钻杆盒内Make sure all alarms are on. 确保所有的警报信号都开着Lay down TDS spinner. 拆下顶部驱动的旋扣器Run in hole bit #15 to bottom. 用15号钻头下钻到井底Run in hole to casing shoe. 下钻至套管鞋Pick up same bit and BHA. 装上同样的钻头和钻具组合Lay down 5” HW drill pipe. 甩5”加重钻杆Move string every 2 hours. 每2小时活动钻具一次Keep area around shaker clean. 保持振动筛区域干净Control trip gas. 控制起下钻气Ream if needed. 如必要时进行划眼Select the best penetration rate. 选择最佳钻进速度Fix the traveling assembly. 固定游动系统Check power tongs and spinning rope are on drill floor. 检查动力钳和尾绳是否在钻台What’s the weight on bit? 钻压是多少?What is the BHA of this well? 这口井的下部钻具如何组合?Drill out cement. 钻穿水泥Drill out 20” casing shoe. 钻穿20”套管鞋Latch the elevator. 扣吊卡Unlatch the elevator. 开吊卡Set the slips. 放卡瓦Adjust the crown-o-matic (crown saver). 调整防碰天车Lock the hook pin. 锁紧大钩销子Check OD of stabilizer. 检查扶正器的外径Perform leak off test. 进行地层破裂(或:渗漏)测试Connect kill and choke line. 接上压井和放喷管线Reverse out the drill pipe. 反循环清洗钻杆Make a short trip. 进行短途起下钻Change the cutters. 换割刀Slug the pipe. 灌重泥浆Drill the stand down. 钻完立柱Start/run the shale shaker. 开振动筛Start the desanders. 开除砂器Start the desilters. 开除泥器Change it with a 40 mesh screen. 换成40目筛布Shut it off. 关掉Pull it to the cat ramp. 把它拉到坡道上去Make a fast connection. 接单根要快Don’t dump the mud into the sea. 不要把泥浆排放到海里Disconnect it with a chain tong. 用链钳卸开Put a thread protector. 加一个(丝扣)护箍Can we use the power slips? 可以使用动力卡瓦吗?Casing and Cementing 下套管与固井Run in hole to bottom for wiper trip. 下钻通井This is the casing program. 这是套管程序Prepare for running casing. 准备下套管Make everything ready for running 7”casing. 做好下7”套管的准备Make cementing job. 固井Displace cementing with mud pump. 用泥浆泵替泥浆Set cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞Pick up cementing head. 接水泥头Cement samples are hard. 水泥样已凝固Pump in 3 cubic meters of spacer. 注3方隔离液Pump down the plug. 泵压(胶)塞Wait on cement. 候凝The guide shoe will be connected. 接引鞋Connect the floor collar. 接浮箍Connect the air line to the casing stabbing board. 接好套管扶正台的气管线Run casing with the 350T slip elevator. 用350吨卡瓦式吊卡下套管Clean and dry 20” casing threads with rags. 清洁并擦干20”套管丝扣Where is the rabbit for drifting the casing? 套管通径规在哪里?Rig Move, Anchoring and Positioning 拖航, 抛锚, 定位What is our position now? 我们现在船位在哪里?Wh at’s the moving speed now? (What’s the towering speed?) 拖航速度是多少? The speed is about 4 knots. 船速是4节左右Which one is the main tug? 主拖是哪条船?The main tug is Nanhai 205. 主拖是南海205Which one is the chase boat? 护航船是哪一条?How much is the horse power? 有多大马力?She has 6000 HP. 有6000马力Move the rig off location 50 feet. 将平台移开50英尺We are ready to drop the anchor. 我们已经做好抛锚的准备了Secure all the movable equipment. 固定好各种活动的设备Preload. (自升式)压载Ballast. (半潜式)压载Put the preload water into the tank. 向压载舱灌压压载水We need 5500 tons of preload water. 需要5500吨压载水Shall we preload right now? 马上开始压载吗?Drain the water off. 放水The rig is overloaded. 平台已超载Jack up (jack down) the rig. 升(降)船The draft is 3.5 meters. 船体吃水3.5米The jetting pressure is 100psi. 冲桩压力是100psiPenetrate the legs. 插桩How much penetration do we have? 入泥多深了?No.1 and No.2 legs indicate 10 meters. 1,2号桩腿插入10米Fix the upper and lower wedges. 固定上下楔块Pay out the anchor line. 放出锚缆绳Skid the derrick. 移开井架The rig is short of potable water now. 平台缺乏饮用水Drop No.2 and No.3 anchors. 抛2号和3号锚Why has the main engine stopped? 主机为什么停?Unleash the drilling tools. 卸开钻具Tighten up. 绷紧(或:上紧)一点Turn on the cooling water for the windlasses. 开锚机刹车冷却水Retrieve the No.1 to No.8 anchors. 起1到8号锚Check the paint marks at the anchor winches. 检查锚机上的油漆记号Prepare for a location move. 准备好移井位Commence anchor handling. 开始起锚(或抛锚)Secure all equipment stored on deck. 固定好所有存放在甲板上的设备Carry out stability and load calculations. 做稳性和载荷计算Pass pendant line, shackle and buoy to anchor handling vessel. 将起抛锚短索, 卸扣和浮标吊起给起锚船Lower the windward anchor to seafloor. 抛上风锚到海底Pick up the leeward anchor first. 先起下风锚Take anchor chaser (or chaser) back to rig. 将捞/抛锚环送回平台Hook up towing lines to tug boat. 将拖缆连接到拖轮Sound fog signal for two seconds every twenty seconds. 发大雾信号, 每20秒钟响两秒Fishing 打捞The bit cutters have been lost in the hole. 牙轮落井Run in the reverse-circulation basket. 下反循环打捞篮There is a lot of junk in the hole. 井下有很多落物The fish is 235.46 meters long. 落鱼长度235.46米The fish top is at 2478.34 meters. 鱼顶位置2478.34米Coring 取芯Stop drilling for coring. 停钻准备取芯Make up core bit. 接取芯钻头What type of core bit is it? 这是什么型号的取芯钻头? Run in a diamond core bit. 下金刚石取芯钻头Let’s drop the ball for coring. 可以投球取芯The core has been broken off. 岩芯断了Put the core in the boxes. 把岩芯装在岩芯盒里Don’t brake suddenly. 不要猛刹车Take out the core. 岩芯出筒How long is the core? 岩芯多长The core recovery is 98%. 岩芯收获率是98%Run in the core barrel again. 继续下岩芯筒(或: 取芯筒)Run in hole core barrel. 下取芯筒Drop ball. 投钢球Recover core. 取出岩芯Use same parameters as for core #1. 使用与1#取芯同样的参数Freeing Stuck Pipe 卡钻与解卡The down-hole problems are very complicated. 井下情况很复杂The hole is tight. 遇阻了Overpull while tripping out. 起钻遇卡(overpull: 超拉力)The formation is unstable. 地层不稳定The wall caving is severe. 井壁垮塌严重There are many return cuttings. 返出岩屑特别多The mud returns have decreased. 返出泥浆减少The hole is enlarged. 井眼扩大了The pipe’s stuck. 卡钻了Pull up to 150 tons. 上提150吨Slack off to 50 tons. 下放至50吨Ream down all the tight points. 在所有遇阻点进行划眼The rotary table can’t rotate. 转盘转不动Where is the sticking point? 卡点在哪里Make a tensile test. 做拉伸试验Back it off above the free point. 在卡点以上倒扣Where is the back-off position? 脱扣位置在哪Plug the well for side tracking. 打水泥塞侧钻Abnormal Well Condition and Well Control异常井况与压井The mud is gas out. 泥浆有气侵The pit has lowered quickly. 泥浆池液面下降很快The hole lost returns. 井口不返泥浆The returns are unstable. 返出泥浆量忽大忽小Where’s the thief zone? 漏失层在哪里Cut down the flow rate. 降低排量Lower the mud density. 降低比重Cut down the hydrostatic pressure. 减少静压The gas smell is strong. 天然气味度很浓There’s some trace of oil. 发现有油花The pump pressure is fluctuating. 泵压不稳It is a zone of abnormal pressure. 这是异常压力层The hole (well) is kicking! 井涌啦!Shut in the BOP! 关闭防喷器Sound the general alarm quickly! 快发出综合警报The stand pipe pressure is 10 kg/cm2. 立管压力10公斤/厘米2The casing pressure is 25 kg/cm2. 套压2510公斤/厘米2Fill out the kill sheet. 填写压井记录表Kill the well. 压井There’s a combination of lost returns and the kick. 又喷又漏, 情况复杂Reverse the gas out of the hole. 反循环排气What’s the lag time? 迟到时间是多少The well is now stable. 现在井眼已经稳定BOP and subsea Equipment 防喷器与水下设备Cut off the 30” conductor. 割掉30”隔水管Weld on the 30” bottom flange. 焊接30”法兰Hoist and nipple up 30” diverter. 吊装30”转喷器Change the 5” pipe rams to 3-1/2” rams. 把这个5”闸板换成3-1/2” Install blind ram. 安装防喷器的盲板芯子Check the seal ring of the conductor. 检查隔水管密封圈Cut off the lifting eye of the conductor. 切割隔水管耳环Test BOP. 测试防喷器Change annular BOP packing. 更换万能防喷器芯子Full pressure test the ram preventers. 对闸板防喷器进行全压试压Test annular BOP at 2500psi. 万能防喷器试压至2500psiCheck annular pressure. 检查环形空间压力Confirm the angle of the guide base. 确定基板角度The thread is covered with the quick-release protectors. 已戴好快卸护丝Establish the guide lines. 装导向绳Connect the TGB running tool. 接临时导向基板送入工具Land the TGB to sea. 下临时导向基板到海底Retrieve the running tool. 退出送入工具Run the BOP and risers. 下防喷器和隔水管Pick up the marine riser. 吊出隔水管Pick up the slip joint. 起伸缩节Adjust the riser tensioners. 调整隔水管张力Function test the diverter system. 对防喷器系统进行功能测试Retrieve the pin connector. 取出销钉连接器Move the BOP to the moonpool door. 将防喷器移到园井甲板的活动门上Run the test plug. 下试压塞Close the upper pipe ram. 关上部钻杆闸板防喷器Open the kill line valve. 开压井管线阀The compensation capacity is 400000 pounds. 补偿能力是400千磅The locking load is 1000000 pounds. 锁紧负荷1000千磅Support the riser. 接隔水管支撑环Remove the hose bundles. 卸下垮接软管Assure the self-controlled rotation. 保证自控转动Set the LMRP on the test pump. 将下部防喷器插入总成座放到试压桩上Connect the flex joint to the riser. 连接隔水管与挠性接头Land the BOP onto the well head. 座防喷器到井口头Run the subsea TV for monitoring. 下水下电视观察Remove all the riser running tools. 取出所有的隔水管送入工具BOP carrier. 防喷器叉车Lower the universal guide frame. 下放万能导向架Paint mark the top 6 meters of 30” conductor white. 在30”隔水管的顶部6米处用白漆涂上记号Check adequate length for guidelines. 检查导向绳的长度是否足够Move temporary guide base (TGB) into moonpool. 将临时导向基板到园井甲板Test pull to check connection. 试拉检查连接Grease TGB and running tool as required. 按要求给导向基板及下入工具上黄油Test fit TGB and running tool. 用下入工具试临时导向基板连接Check for junk inside shoe joint. 检查浮鞋内有无落物Pick up 30” conductor handling slings and shackles. 吊上下30”导管的索具和卸扣Is slope indicator properly mounted? 水平仪是否装好?Ensure subsea TV is in good condition. 确保水下电视处于良好的状态Place BOP stack on the test pump. 将防喷器组放在试压桩上Check condition of all 30” casing connectors. 检查所有30”套管接头的情况Replace O-rings as required. 按需要, 更换O性密封圈Attach slope indicator below camera position. 在摄像机下面装上水平仪Inspect and repair diverter. 检查并修理转喷器Prepare spud plate and wireline to check water depth. 准备测深板和钢丝绳测量水深Record all pressure tests on a chart recorder. 用试压表记录试压记录Visually inspect all sealing element. 目视检查所有密封件Check and tighten all bolts. 检查并上紧所有螺栓Bleed off surface accumulators. 地面管线排空气Check for leaks. 检查有无泄漏Lift BOP stack and replace wellhead connector AX ring. 吊起防喷器组并更换连接器AX密封圈Function test wellhead. 对井口头进行功能试验Fill kill and choke valves with seawater. 将压井阀和阻流阀注满海水Pressure test to 500psi then bleed off test pressure. 试压到500psi, 然后放掉压力Reduce hydraulic control manifold pressure to 5200 kpa. 将液压控制管线压力减少到5200千帕Switch to alternate control pod. 把闸门开关倒到控制面板Guidelines are slacked off. 导向绳松了Slack off drill pipe and release running tool. 放松钻杆并卸开下入工具Run subsea TV to observe bit entering the TGB. 下水电视观察钻头是否进入临时导向基板Don’t rotate until ho le opener passes through the TGB. 在扩眼器通过临时导向基板前不要旋转Position permanent guide base (PGB) below rotary table. 在转盘下安放永久导向基板Monitor riser level via trip tank. 用计量罐来控制隔水管内的液面Pressure test to 5000psi. 试压5000psiPick up test mandril and place in BOP. 吊起试压防喷器芯子并装入防喷器组Safety and Firefighting 安全与消防Get a Work Permit before you can start the hot work. 办理作业许可证才能进行动火作业Welding is not allowed. 不准动焊Put on your (safety) helmet. 戴上安全帽It’s a high voltage area. 这是高压区That’s against the rule. 这是违章作业Don’t walk under the crane load. 不要在吊物下走动The repairing is under way. 正在检修Keep your hands clear! (Keep you hands off! Do not touch!) 不要乱动Wear and secure your safety belt. 戴上并系好安全带Life jacket must be worn when working outboard or overhead. 舷外或高空作业要穿救生衣Have your breathing apparatus near you. 保持放毒面具在附近It’s a drill. 这是演习It was a BOP drill. 这是防喷演习Get in the lifeboat in order. 按顺序进入救生艇Put on life jacket! 穿好救生衣Abandon the vessel! 弃船Sound the abandonment alarm! 发出弃船警报Go to the helideck! 去飞机坪集合Aboard the lifeboat. 登上救生艇Aboard the supply boat to shore! 乘拖船上岸Check life saving apparatus periodically. 定期检查救生设备It’s for fire fighting. 这是消防用的Start the fire pump. 启动消防泵This rope is too small. 这根绳子太细了It should be function tested. 需做功能测试A warning notice should be set up. 要挂警告牌Do you have an emergency program (contingency plan)? 你们有没有应急计划?It must be ready in an emergency condition. 必须始终保持良好的应急状态Will the typhoon hit our rig? 台风要袭击我们的平台吗?We will have to evacuate the rig. 我们要撤离平台Personnel on board (POB). 在船人员总数Sound fire alarm. 发消防警报This is a fire drill. 这是消防演习conduct abandon ship drill. 举行弃船演习Release the boat hooks. 释放救生艇吊钩Board the life boat. 登救生艇Remove the rust and paint with anti-corrosive primer. 除锈后上防锈底漆Three rafts are located near life boat station port side. 在左舷救生艇站附近还存放有3个救生筏Wear work vests when working below the cellar deck. 在圆井甲板面下面工作时须穿工作救生衣The station bills need to be updated. 应急部署表须更新Check the expiry date for all foam extinguisher. 检查所有泡沫灭火器的过期时间Close all the water-tight doors. 关闭所有水密门Safety procedure shall be followed at all the times. 在任何时候都应遵守安全程序Anchor wires should have a Spelter type socket at anchor side. 抛锚绳靠锚的一端应使用锌压头Colour code all the connection at the loading station. 在供给站管线接头处用颜色表明各管线Verify that a high level alarm is installed on the sludge tank. 确认污水舱安装有高位警报Don’t switch on during drilling operation. 钻井作业期间不能合闸Provide two independent means to start the emergency generator engine. 应急发电机柴油机应有两套独立的起动方法Have the boom pennant wires of port crane re-certified. 重新认证左舷吊车扒杆变幅绳Clean the internals of the emergency switchboard. 清洁应急配电盘内部Helicopter and Supply Vessel 直升机与供应船Load out Contractor’s riser at Zhanjiang anchorage. 在湛江锚地把承包商的隔水管装上平台Offload casing. (从供应船上)卸套管Load (offload or unload) the boat. 装(卸)船Get the food container loaded on the boat. 把食品集装箱装上船The helicopter will land on rig soon. 直升机很快就要在平台降落Tell the base to get (or send) a chopper here. 通知基地派飞机来Helicopters are not allowed to land here. 飞机不能降落Report the weather condition to the pilot. 向飞行员报天气Inform the boat come to standby. 通知拖轮过来待命Call the boat to come along port side. 通知拖轮过来靠左舷We will take the personnel basket. 我们乘坐吊篮。
海上采油英语实用手册(英汉对照)-单词及短语
diaphragm valve
diesel storage tank differential pressure
. control valve
单词及短语
柴油储罐
采油工艺及设备
差压控制阀
放空阀
23. dispersed gas floatater
自动排放阀 24. displacement oil pump
43. 44.
heater treater feed phuimgph pressure condensate drum
加气浮选器 置换油泵 排放池 电脱盐器 电液控制阀 电潜泵 紧急关断阀 细滤器洗刷风机 一(二)级分离器 火炬燃烧总成 火炬点火气 浮球控制阀 浮式生产储油系统 自由水分离器 淡水制造装置(造水机) 燃烧气加热器 燃烧气系统 易熔塞 伴热管线 加热器 热处理器供液泵 高压冷凝水罐
反冲洗循环泵 25. drain pit
双孔盲法兰 排放罐
锅炉提升泵 离心泵
化学密封 净化水缓冲罐 闭式排放罐
26. electric desalter
27.
electric - hydraulic valve
28. electrical submergible
29. 30. 31.
emergency shutdown vfailnveefiltration scour bfliorwsetr(second) stage separator
32. flare assembly
聚集器 冷凝液罐 波形斜板隔油器 原油冷却器
33. flare pilot gas
34. 35.
floater controlled vFaPlSvUe-floating oil production and storge
海洋石油钻井常用英语
海洋石油钻井常用英语附录一:平台人员岗位名称一.承包商人员( Contractor’s Personnel )Rig Manager平台经理Equipment Supervisor设备总监Materials Supervisor材料总监Senior Toolpusher高级队长Junior Toolpusher值班队长Driller司钻Sub Sea Engineer (SSE)水下工程师Assistant Driller (AD)副司钻Derrick Man井架工Floor Man (roughneck)钻工Barge Master (captain)船长First Mate (Barge engineer)大副Control Room Operator (CRO)压载工Ballast Control Operator (BCO)压载工Chief Engineer轮机长Head of Routabout甲板班长Crane Operator吊车工Routabout甲板工Mechanic机械师Electrician电气师Repairman修理工Motorman轮机员Welder焊工Radio Operator电报员Warehouse Man (stock Keeper)材料员Medic医生Safety Supervisor安全监督Interpreter (translator)翻译Chief Steward管事Cook厨师Steward厨工Laundry Man洗衣工二.作业者及服务公司人员( Operat or’s Personnel and Service Company Personnel) Drilling Superintendent钻井监督Company Man (Operator’s Representative)公司代表Geologist地质师Mud Logging Engineer (Mud logger)泥浆录井工程师Sample Catcher捞砂工Mud Engineer泥浆工程师ROV Engineer潜水工程师Cementer固井工Cement Engineer固井工程师Testing Engineer试油工程师Coring Engineer取芯工程师Wireline Logging Engineer电测工程师附录二:平台主要设备一.钻井设备(Drilling Equipment): Drawworks钻井绞车Rotary Table转盘Bushing补心Top Drive System (TDS)顶驱Swivel水龙头Crown Block天车Traveling Block游车Hook大钩Derrick井架Pipe Spinning Wrench钻杆气动扳手Ezy-Torq液压猫头Elmagco Brake涡磁刹车Pipe handling Equipment钻杆移动设备Iron roughneck铁钻工Pipe Racking System钻杆排放系统Drill String钻柱Drilling Sub钻井短节Fishing Tool打捞工具Power Tong动力大钳Air Winch (air tugger)气动绞车Crown-O-Matic (Crown Saver)防碰天车二.泥浆系统(Mud System) Mud Pump泥浆泵Shale shaker振动筛Mud Cleaner泥浆清洁器Desilter除泥器Desander除砂器Degasser除气器Centrifuge离心机Mud Agitator泥浆搅拌器Mud Mixing System泥浆混合系统Centrifugal Pump离心泵Standpipe Manifold立管管汇Rotary Hose水龙带Bulk Air System and Tank吹灰系统和灰罐三.井控设备(Well Control Equipment): Ram Type Preventor闸板防喷器Annular Type Preventor万能防喷器BOP Stack防喷器组Gate Valve闸阀Choke and Kill Manifold阻流压井管汇Remotely Operated Panel远程控制面板Choke Control Panel阻流控制面板BOP Handling Equipment防喷器搬运设备Diverter转喷器四.海事系统(Marine System)Ballast System压载系统Bilge System污水系统Vent通风口,通气口Air Supply Fan供气扇Mooring System锚泊系统Communication Equipment通讯系统Jacking System升降系统Skidding System井架滑移系统Windlass锚机Anchor锚Pendant短索。
石油专业英语（钻井）
石油专业英语（钻井）2008-08-02 21:02Drilli ng 钻井Carryout drilli ng operati on in accordance with the drilli ng progra m. 按钻井程序进行钻井作业.Prepared bell nipple. 准备”喇叭口”短节.Make up 2 joints of drill pipe. 接两根钻杆.Breakout this connection. 卸开该接头.Run hole opener to sea bed. 下扩眼器到海底Mix gel fluidfor drilli ng conductor hole. 为钻导管井眼配制高粘度泥浆.Make up bottom hole assembl y. 组合下部钻具Checkand resetcrown-saveron everytour. 每个班都要检查并重新调整天车防碰装置.Number stands on trip out and trip in. 起下钻时给立柱编号.Pick up BHA and run to seaflo or. 将下部钻具下到海底.Pick up stands. 接立柱（一个立柱就是三根钻杆接在一起）Don’t drill faster than 15 minute s for 1 stand. 钻进速度别超过15分钟1根立柱Drop TOTCO. 投(陶特)测斜仪Fish TOTCOwith oversh ot. 用打捞筒捞起测斜仪Resume drilli ng to T.D. 继续钻进到总深Circul ate 15 minute s.循环15分钟Run in hole. 下钻Put out of hole. 起钻Make an invent ory of all ring gasket s. 开一个所有垫圈的清单Use spinni ng tong. 使用气动扳手Operat e the air winch. 操作气动绞车Lay down 57 joints of 5”drill pipe. 甩57根钻杆Pick up drill stem test tool. 提起钻杆测试工具Circul ate mud for 2 hours. 循环泥浆2小时Move string during circul ation. 在循环时注意活动钻具Circul ate hole clean. 循环清洗井眼Circul ate bottom s up. 循环泥浆几周Fill up every 5 stands. 每5柱灌泥浆一次Checkmud weight every15 minutes. 每15分钟检查泥浆比重Reverse out excess cement. 反循环替出多余的泥浆Change/replace old mud by new mud.用新的泥浆替换出旧的泥浆Stop drilli ng. 停止钻进Drilli ng ahead. 钻进Pull out of hole bit. 起出钻头Change bit. 换钻头Run the wear bushin g. 下抗磨补心The bit thread type is regula r pin. 钻头丝扣是正规公扣What’s the make-up torque? 上扣扭矩要多大?Run in 9”collars. 下9”钻铤The cathea d can’t give enough torque. 猫头力量不够Connect crosso ver sub. 接上配合接头The tong anglei s too small. 大钳的角度太小了地质年代术语英汉对照2008-08-0221:04stra tum 地层strati graphi c correl ation地层对比horizo n 层位key bed 标志层barren bed 哑层lacuna缺失hiatus 间断contin uity连续discon tinui ty 不连续conformity整合unconformit y 不整合angula r unconformit y 角度不整合para-unconformit y 平行不整合geochronolo gi c unit 地质年代单位eon 宙era 代period纪epoch世stage期chron时chrono strati grap hic unit 年代地层单位eonoth em 宇erathe m 界system系series 统stage阶chrono zone时带biostratigraphic unit 生物地层单位biostratigraphic zone 生物地层带lithostrati graphi c unit 岩石地层单位group群formati on 组member段bed 层geochronolo gi c scale地质年代表Phaneo zoicEon(Eonoth em)显生宙（宇）Cainoz oi c Era(Erathe m) 新生代（界）Cenozoi c Era(Erathe m) 新生代（界）QuaternaryPeriod(System)第四纪（系）Holoce ne Epoch(Series) 全新世（统）Pleist ocene Epoch(Series) 更新世（统）Tertia ry Period(System) 第三纪（系）Neogen e Period(System) 新第三纪（系）Plioce ne Epoch(Series) 上新世（统）Miocen e Epoch(Series) 中新世（统）Paleog ene Period(System) 老第三纪（系）Oligocene Epoch(Series) 渐新世（统）Eocene Epoch(Series) 始新世（统）Paleocene Epoch(Series) 古新世（统）Mesozo i c Era(Erathe m) 中生代（界）CretaceousPeriod(System) 白垩纪（系）Jurassi c Period(System) 侏罗纪（系）triassi c Period(System) 三叠纪（系）Palaeo zoicEra(Erathe m) 古生代（界）Permia n Period(System) 二叠纪（系）Carboni fero u s Period(System) 石炭纪（系）Devoni an Period(System) 泥盆纪（系）Siluri an Period(System) 志留纪（系）Ordovi c ianPeriod(System) 奥陶纪（系）Cambri an Period(System) 寒武纪（系）Crypto zoicEon(Eonoth em) 隐生宙（宇）Proterozoic Eon(Eonoth em) 元古宙（宇）Neopro teroz oic Era(Erathe m) 新元古代（界）Sinian Period(System震旦纪（系）Mesoprotero zoicEra(Erathe m) 中元古代（界）Palaeo prote rozoi c Era(Erathem) 古元古代（界）Archae an Eon(Eonoth em) 太古宙（宇）Precam brian前寒武纪石油钻井词汇Part One SLICK-LINE（钢丝作业）A. TOOLSrope socket绳帽stem 加重杆roll stem 滚轮加重杆Tungst en stem 钨加重杆Lead stem 铅加重杆link jar 机械震击器tubula r jar 管状震击器hydrau lic jar 液压震击器spring jar 弹簧震击器knuckl e joint万向节swivel joint旋转节wellhe ad adapte r 井口变扣短节X-Over 变扣gaugecutter通井规select ive downsh ift tool 选择性滑套开关工具shiftt ing tool 移位工具blindbox 盲锤L.I.B(lead impres sionblock)铅印swagin g tool 胀管器spear打捞矛pronggrab 内捞矛center spear外捞矛catche r 捕捉器wirefi nder钢丝探测器Go devil-F.B 平底撞棍Go devil-C.B 刀杆撞棍retrie ver 钢丝打捞器oversh ot 卡瓦打捞筒magnet ic fishin g tool 磁力打捞工具sidewa ll cutter刮管刀alliga tor grab 鳄鱼爪sand bailer捞沙筒pipe wrench管钳tong chain链钳spanne r 扳手wireli ne clamp钢丝夹hay pulley地滑轮dump bailer倾倒筒saw 锯子saw blade锯条punch冲子file 锉刀flat file 板锉,扁锉hammer榔头pliers,vice 老虎钳wire cutter断线钳forfex剪刀tongs大钳,钳子,管钳flat bit tongs扁嘴钳screwd river改锥，螺丝刀wire stripp er 剥皮钳,掳线钳wire-stripp er pliers剥线钳B. EQUIPM ENTstuffi ng box 防喷盒lubric atoruppersectio n 上防喷管lubric atormiddle sectio n 中防喷管lubric atorlowersectio n 下防喷管blowou t preven ter(BOP) 防喷器wellhe ad adapte r 井口变扣短节Lincol n pump 林肯泵hand pump assy.for stuffi ng box 手压泵Fire exting uishe r 灭火器hand tool box 手工具箱inject or 注油器liftin g cap BOP吊帽trolly防喷管支撑架paraso l 阳伞work vice 台钳chainblock链葫芦tie down chain系紧链fixedpulley定滑轮wobble pump 手摇泵wire line clamp钢丝绳夹wire rope sling绳套,钢丝吊绳winch绞车winchbarrel(drum) 绞车滚筒winchbrake绞车刹车winchdriveshaftuniver sal joint绞车主动轴万向节winchdrum shaft绞车滚动轴winchline 吊装用绳套winchcontro l panel绞车控制面板winchtruck吊车C. OPERAT IONSRTTS Operat ion for ShootandPull RTTS完井服务RTTS Operat ion for CementSqueez ing RTTS固井服务（挤水泥）Pullin g Y Block捞Y堵塞器Open SSD(SlideSide Door) 开生产滑套CloseSSD(SlideSide Door) 关生产滑套Open Circul ating SSD(SlideSideDoor) 开循环滑套CloseCircul ating SSD(SlideSideDoor) 关循环滑套Runnin g GaugeCutter通井Cleanup 地面完井放喷Open DrainValve砸泻油阀Pullin g Test Plug 捞测试阀Runnin g Jet Pump 投射流泵Pullin g Jet Pump 捞射流泵Runnin g Flow Regula tor 投配水器Pullin g Flow Regula tor 捞配水器Fishin g Drop Bar 捞点火棒Measur ing Static Pressu re 测静压Measur ing Flowin g Pressu re 测流压Measur ing BHPBU(Bottom Hole Pressu re BuildUp) 测压力恢复Measur ing BHP(Bottom Hole Pressu re) Testin g with Jet Pump 带泵测压（射流泵）Multi-Rate BHP(Bottom Hole Pressu re) Testin g 系统试井Slick-line Operat ion for Comple tion钢丝配合完井服务Slick-line Operat ion for acidiz ing 配合酸化钢丝作业Runnin g Plug 投堵塞器Pullin g Plug 捞堵塞器Run Impres sionBlock下铅印Runnin g Prong投平衡杆Sand Leveldetect ion 探沙面Run Sand Bailer下捞砂桶Open SSSV(Sub Surfac e Safety V alve)by Force强行打开井下安全阀Runnin g Go Devil剪切钢丝Fishin g Slickl ine 打捞钢丝Runnin g Side Pocket Plug 投偏心堵塞器Pullin g Side pocket Plug 捞偏心堵塞器Runnin g Side Pocket CheckValve投偏心阀Pullin g Side Pocket CheckValve捞偏心阀Sand Sampli ng 取砂样Stable Test 稳定试井Slickl ine Swab 抽吸Runnin g Hanger投悬挂器Pullin g Hanger捞悬挂器D. SPAREPARTSgrease inject ion contro l head 注脂头grease oil 注脂油grease oil tank 注脂油桶BOP pump c/w hose 手压泵及管线pressu re test hose 试压管线lubric atorbleedoff manifo ld 防喷管针阀Martin Decker W-15 oil 马丁代克油Martin Decker WT indica tor c/whose 指重器及管线pickin g for stuffi ng box 盘根bearin g for the sheave for stuffi ngbox 轴承O-ring for lubric ator防喷管O环ram assemb ly for BOP 防喷管闸板总成O-ring for BOP BOP O环O-ring for wellhe ad adapte r 井口变扣O环pin 销钉counte r head 计数头cablefor counte r 计数器软轴bearin g of hay pulley地滑轮轴承Part two Pressu re gaugeaccord ance一致,和谐accura cy 精确性,正确度acquis ition获得,获得物alignm ent 校直,调准append附加,添加,悬挂apply申请,应用availa ble 可利用的,有用的batter y 电池batter y housin g 电池筒batter y tester电池测量器baud rate 波特率bull nose 底堵cable电缆,电线cablehead 电缆头,电缆接头calcul ation计算,考虑calibr ation标度,刻度,校准calibr ation drift漂移calibr ation parame ter 标定参数cartes ian 笛卡儿曲线certif icati on 证书com port 串行通讯端口comman d 命令,掌握,支配commun icate沟通,交流,通讯compen sate偿还,补偿config urati on 构造,结构,配置,外形config ure 配置,设定consis t 组成,构成contro l panel控制面板conver t 转换,使转变cross-over betwee n gauge压力计间变扣crysta l 水晶,晶体curren t 电流damage危险,损害data acquis ition获得数据decode解码,译解deltatime 累计时间deviat e 偏离diagno stic诊断diamet er 直径digita l 数字的direct ory 目录discus sion讨论displa y 显示器,显示,展示downho le tools井下工具drain消耗,耗尽dump data 回放数据durabi lity耐用性elemen t 元素,元件,成分elevat ed temper ature高温encode r 译码器,编码器establ ish 建立,安置filter过滤,筛选firmwa re 固件(软件硬件相结合)fixedrate 固定采样率flash闪光,闪现freque ncy 频率,周率gauge压力计graph图表,曲线图grease for transd ucer传感器用油housin g 壳,壳体incorp orate合并,混合indica te 指出,显示indivi dual个别的,单独的instal l 安装,安置instru ment工具,器械,器具interf ace box 接口箱interf ace box 接口箱intern al diagno stics内部诊断lapse失误,下降,过失linear plot 线性平面图log 日志mainte nance维护,保持manual手册,指南manufa cture制造,加工merge合并,并入,结合memory存储器,内存module模块observ e 观察,观测offer提供,企图parall el commun icati on 并行通信period周期,时期plug 堵,塞,插上,插栓port 端口,港口potent ial 潜在的,可能的presen tatio n 陈述,表达presen tatio n softwa re 操作软件printe r 打印机prior优先的,在前的proced ure 步骤,手续progra m 程序,节目prune剪除,修剪,删除qualit y 质量,品质,性质quartz石英range范围,射程real time 实际时间record mode 记录模式reduce减小,缩小,简化remote contro l 遥控,遥控操作remove移动,开除,移交requir e 请求,要求resolu tion分辨率respon se 回答,响应scale刻度,天平,比例尺select选择,挑选setup机构,安装,装备,组织silico ne oil 硅油sleepmode 休眠模式spanne r for gauge压力计专用扳手SRO(surfac e read-out) 地面直读surpas s 超过,胜过talk mode 对话模式termin al 终点终端thread grease丝扣油transd ucer传感器,变频器,交换器transi ent 短暂的,瞬时的transm it 传输,传送,发射信号transp ort 传送器,运输机transp ortat ion box 压力计箱troubl eshoo ting发现并修理故障trunca te 截取,修剪update更新,校正,修正upload上载variab le rate 可变采样率variou s 不同的,多样的versio n 版本,译本volt 伏特voltag e 电压wand 棒,棍,杖zoom 放大,缩放Part threePVT取样 air chambe r plug extrac tor 空气室拉出手柄air chambe r plug retain ing ringextrac tor 梭管套旋出手柄air chambe r tube assy 导流管air hose assy. 扫空管allenkey 内六角autocl ave vacuum nipple抽真空头B/benchhose assy. 样瓶转样管back-up ring 背环compre ssion spring压缩弹簧filler funnel漏斗flow regula tor body 节流器flow regula tor end cap 端帽flow regula tor extrac tor 节流器拉出手柄fuse/110V 保险丝/110Vglycol甘醇heatin g jacket for cylind er 样瓶加温器heatin g jacket for sample r 取样器加温器holder装配手柄intern al circli p 内簧卡intern al circli p for cylind er 取样瓶卡环lock grubsc rew 锁紧螺丝needle valve针阀needle valveassy.extrac tor 针阀手柄needle valvebody 针阀组件needle valveBUR former针阀背环工具off ball 钢球off disksp ring弹簧片piston assy. 活塞总成piston remova l 活塞移位工具piston ring 活塞环piston rod 活塞杆piston valvestem 梭阀杆pols-lock pin 锁定销钉pols-lock spring锁定销钉弹簧posi lock pin depres singtool 锁定按压工具primehand pump 注油器primehand pump adapto r 注油器适配器primeport adapto r assy. 加压口适配器primeport nipple plug 加压口堵头primeport spanne r 加压阀扳手primepump assy. 手压泵适配器primepump hose assy. 手压泵输出管push rod 推杆relief valvestem 调压阀杆retain ing ring 制动环revers iblecircli p pliers卡簧手钳safety solven t 清洗液sample analys is 试样分析,样品分析sample analyz er 试样分析器sample bailer采样筒sample blob 井底取样器sample bomb 高压取样瓶,样品存储器sample bottle取样瓶,采样瓶sample bottle valveadapto r 样瓶接头sample chambe r 样品室sample cock 取样旋塞,取样拷克sample collec tion取样,样品收集sample collec tionproced ure 取样点,采样点sample collec tor 取样程序sample connec tion试样收集器,采样员sample contai ner 取样接头sample contam inati on 样瓶,样筒,样品容器sample cup 样品污染sample cylind er 样品杯sample cylind er tag 样瓶,样筒sample date 样瓶标签sample depth取样日期sample freque ncy 采样深度sample hose 采样信号sample identi ficat ion 取样井,采样井sample integr ity 采样频率sample interv al 样品管,采样胶皮管sample period样品鉴定sample point样品的真实性sample signal取样间隔,取样速度sample well 取样周期sample r hose assy. 取样器软管总成settin g screw制动螺丝settin g fork 导流叉管settin g tool 空气定位销手柄settin g tool 梭杆推进套shuttl e mechan ism assy. 触发机构tee ring sealsT型密封环test gauge压力表tool body clamp取样器夹具tool dressi ng aids 更换'O'环工具torque wrench扭矩扳手torque wrench adapto r 扭矩扳手接头torque wrench adapto r 扭矩扳手接头transf er benchassy. 转样器总成transf er lock sleeve转样护帽transf er port adapto r 转样适配器transf er port plug 转样口堵头trigge r mech. assy. 触发机构总成trigge r spring触发弹簧vacuum hand pump 真空泵vibragauge压力表Part four OthersAa direct ional engine er 定向井工程师a drilli ng engine er 钻井工程师a drilli ng superv isor钻井监督a senior mud engine er 高级泥浆工程师a toolpu sher队长，技师abando ned drill弃船演习accele vator促凝剂acidit y 酸性adapte r 接头additi ve 添加剂/处理剂aheadwater先行水air chambe r 空气包air hoist气动绞车alarm警报alkali nity碱性泥浆比重amplit ude log 声幅测井anchor锚angle角钢annula r return veloci ty 泥浆返回流速annula r space环形空间annula r veloci ty 环空流速appare nt viscos ity 视黏度asbest os 石棉assist ant tug boat 护航船assist ant drille r 副钻aviati on fuel 航空油Bback off 倒扣back pressu re 回压back pressu re valve回压阀ball 球ball up 泥包bargeengine er 平台工程师barite重晶石bearin g 轴承bearin g angle方位bed 床behind water尾水bit 钻头bit bearin g 钻头轴承bit breake r 钻头装卸器bit cost 钻头成本bit diamet er 钻头直径bit gauge钻头规bit life 钻头寿命bit nozzle钻头水眼bit positi on 钻头位置bit sub 钻头接头bit time 钻头纯钻时间bit tooth钻头牙齿bit torque钻头扭矩bit type 钻头型号bit wear 钻头磨损blasti ng cap 雷管blow out 井喷blow out preven ter 防喷器boiler锅炉bolt 螺栓bolt,nut 螺丝,螺母bore hole 裸眼bore hole well 井壁boring钻孔bottom hole 井底bottom fill 沉砂bottom hole pressu re 井底压力bottom hole pressu re 井底压力bottom s up 携带岩屑box 母扣brake刹车breakout 卸扣breech lock 泡栓buildup 压力恢复bulk densit y 堆积密度;松装密度bulk tank 灰罐bumper sub 缓冲器buoyan cy coeffi cient浮力系数bushin g 补芯butane丁烷Ccable电缆calciu m remove r 除钙剂calcul ating free piont计算卡点深度calibr ation刻度casing套管,螺纹联接的兀接箍casing head 套管头casing spool套管四通casing burstpressu re 套管破裂压力casing elevat or 套管吊卡casing monkey board套管平台casing pressu re 套压casing progra m 套管程序casing scrape r 套管刮管器casing shoe 套管鞋casing sub 套管接头casing tong 套管大钳cathea d 猫头cave in 坍塌cement水泥cement basket水泥伞cement bond log 固井质量检验cement flush水泥冲洗cement slurry水泥浆cement slurry for lead 先行水泥浆cement ing 固井cement ing line 固井管线cement ing pump 固井泵center latch elevat or 中开门吊卡centra lizer套管扶正器centri fugal pump 离心泵chain block倒链change bit 换钻头chart卡片check valve单流阀chemic al tank 化学药剂缸chemic al treatm ent 化学处理chemic als 化学剂choke油嘴chokeline 阻流管汇choke manifo ld 试油树christ mas tree 采油树circul ating pressu re 循环压力circul ation循环circul ation rate 循环速度clamp卡子clay contam inati on 粘土侵clock时钟clog house值班房cock 水龙头coeffi cient of fricti on 摩擦系数colloi d 胶体comple tion完井comput er 计算机conduc tor 隔水导管cone 牙轮cone bit 牙轮钻头connec tor 联结器contam inati on of mud 泥浆污染contra ct 合同contra ctor承包商contro l room 控制室conven tiona l mud 普通泥浆cooker炊事员core 岩心core barrel取芯筒core bit 取芯钻头core catche r 岩心爪core gun 取芯器core handli ng tools取芯工具core recove ry 取芯收获率coring取芯coupli ng 联接扣cover外壳crane operat or 吊车司机critic al veloci ty 临界速度cross十字接头crossover,x-over(XO) 大小头，短节，变扣接头，旁通管crosso ver sub 配合接头crown block天车cut off workli ne 割大绳cylind er 缸Ddaily produc tion日产量deadli ne 死绳deadli ne anchor死绳固定器deck 甲板declin ation偏差/方位角degasser 除气器dehydr ation失水densim eter密度计depth井深derric k 井架derric k man 架工desand er 除砂器desilt er 沉淀池, 滤水池detona tor 炸药deviat ion survey井斜测量diamon d bit 金刚石钻头die collar打捞卡瓦diesel oil 柴油differ ent pressu re sticki ng 压差卡钻direct ional well 定向井discha rge of pump 泵排量disper sing agent分散剂displa ce 替diver潜水员doctor医生drag 遇阻draw works绞车drier(dringoven) 干燥计drift angle倾角driftmandre l 通径规drifti ng 通径drillpipe 钻杆drill spool钻井四通drillstem 钻柱drill string s 钻杆拄drill water钻井水drillcollar钻铤drillfloor钻台drillfloor钻台drille r 司钻drilli ng 钻进drilli ng techni cian钻井技术员drilli ng assemb ly 钻具组合drilli ng break进尺突然加快drilli ng cost 钻井成本drilli ng crew 钻井队员drilli ng engine er 钻井工程师drilli ng equipm ent 钻井装置,钻机drilli ng line 大绳drilli ng log 钻井记录drilli ng ration钻速drilli ng record er 钻井记录仪drilli ng rig 钻井船drilli ng troubl es 井下事故drum shaft滚筒轴DST(drillstem test) 延长DST测试dump valve放泄阀duplex slushpump 双缸泥浆泵DV collar分级注水泥短接DV port DV孔Eelbow弯接头electr ic loggin g 电测electr ic submer ged pump(ESP) 电潜泵electr ician电工elevat or 吊卡elevat or link 吊环emulsi fier乳化剂engine room 机舱erecti ng equipm ent 安装设备erecti ng tools安装工具erodeout 刺坏error误差ethane乙烷explor ation勘探extend ed well testin g 延长测试extern al upset外加厚Ffalsethread ing 造扣fieldmainte nance现场维护，现场保养fill line 灌泥浆管线fillin g up mud 灌泥浆filter cake 泥饼filter paper滤纸filtra tion educin g agent降失水剂finger board指梁fire drill消防演习fishin g 打捞fishin g bumper sub 打捞缓冲器fishin g jars 打捞震击器fishin g job 打捞作业fishin g neck 打捞颈fishin g tools打捞工具fishin g up 打捞出落鱼flash welded tool joint闪光焊接接头flashl ight手电float collar浮箍floatshoe 浮鞋floorman 钻工flow 放喷flow line 泥浆出口管线flow rate 流量flow line 出油管flow rate 流速flowin g bean(nipple) 油嘴flowin g pressu re gradie nt 流压梯度fluidloss 失水量fluore scenc e 荧光反应format ion 地层format ion conduc tivit ies 地层电导率format ion damage破坏地层fractu ring压裂free pipe 未卡部分钻柱free point自由点free standi ng mast 无绷绳轻便井架fresh water淡水full hole(FH) 贯眼扣functi on 函数funnel viscom eter漏斗黏度计Ggammaray 射线gammaray log 自然测井gas reserv oir 气层gas analys is 气体分析gas chroma togra phy 气体色谱仪gas cut 气侵gas in mud 泥浆中气量gas oil ratio油气比gas out 气侵gas showin g 气体显示gasoli ne 汽油gauge量规gear 牙轮gel 凝胶gel cement胶质水泥gel mud 胶质泥浆gel streng th 切力genera tor 发动机geothe rmal gradie nt 地温梯度gooseneck 鹅颈管grade级/等级grease黄油guideshoe 引鞋gun perfor ation射孔完井gypsum mud 石膏泥浆Hhammer锤子hard ware 硬件heavymud 重泥浆/加重泥浆heavy viscos ity mud 高粘泥浆heavy weight drillpipe 加重钻杆heavybodied很稠的，粘滞的helico pter直升飞机helico pterport 飞机平台helmet安全帽hole opener扩眼器hole size 井眼尺寸hole straig hteni ng 井眼校正/纠斜hook 大钩hook load 大钩负荷hook load off bottom钻柱离底时大钩负荷hook positi on 大钩位置hopper漏斗hose 软管/水龙带hull 船身hydrau lic pressu re 静水压力hydrau lic oil 液压油hydros tatic pressu re 静水压力IIF(intern al flush)内平扣indent ed bolt 齿纹螺栓indent ed chisel齿状钻头，牙轮钻头indire ct flushi ng 反循环洗井，反向冲洗induct ion electr icalsurvey感应电测井inerti a brake惯性刹车initia l gel streng th 出切inner barrel内岩心筒inner string cement ing 内管注水泥input输入insert bit 镶齿钻头inside bop drill安装回压凡尔演习intake profil e 吸水剖面intern al upset内加厚intern al-extern al upset内外加厚interp reter翻译invade d zone 侵入带invasi on diamet er 侵入直径invers e circul ation反洗井invers e well-flushi ng 反洗井isobut ane 异丁烷isopen tane异戊烷Jjack knifemast 折叠式轻便井架jack up type drilli ng unit 自升式钻井船jars 震击器joint单根junk basket打捞蓝Kkelly方钻杆kelly bushin g 方钻杆补芯kellycock 方钻杆考可kellydown 方入kelly down depth方入深度kelly drive方钻杆滚子补芯kelly spinne r 方钻杆旋扣器kellyup 方余key seat 键槽key seatin g sticki ng 键槽卡钻kick 井涌kick contro l 控制井涌kill line 压井管汇killin g a well 压井Llamina r flow 层流latchi ng elevat or 扣吊卡lay down 甩lay time 迟到时间leak 漏life raft 救生筏lifebo at 救生艇lift jacket救生衣liftin g sub 提升短接light weight mud 轻泥浆lignit e 铁络盐lignit e mud 铁络盐泥浆lime 石灰lime mud 石灰泥浆limit switch相限开关line 管线line cleani ng 管线清洗line test 管线试压liner缸套,尾管liner hanger尾管挂living quarte rs 居住区loadin g 装船loggin g cable测井电缆loggin g progra m 测井程序loggin g tool 测井工具loosen放松lost circul ation井漏lost circul ation materi als 堵漏剂lubric ating oil 润滑油lubric ator(assemb ly,system) 防喷管（装置，系统）Mmachin e oil 机油main tug boat 主拖轮make up 上扣make up torque上扣扭矩mast 钻机master bushin g 转盘大补芯master valve总闸门materi al man 材料员mean sea level平均海平面mechan ic 机械工mechan ist 机械师methan e 甲烷mica 云母milled teethbit 铣齿钻头millin g tool 铣具/磨鞋miring water溶解水mixing pump 混合泵monkey board二层台mornin g tour 白班motorm en 机工mousehole 鼠洞mud 泥浆mud agitat or 泥浆搅拌器mud balanc e 泥浆密度计mud column泥浆柱mud condit ionin g 泥浆处理/配泥浆mud conduc tivit y 泥浆导电率mud densit y 泥浆密度mud ditch泥浆槽mud flow meter泥浆流量计mud gun 泥浆枪mud line 泥浆管线mud loggin g 泥浆录井mud pump 泥浆泵mud resist ivity泥浆电阻率mud retort泥浆蒸馏水mud return line 泥浆返出管线mud tank 泥浆池mud temper ature泥浆温度mud testin g 泥浆测试mud volume泥浆量mud weight indica tor 泥浆比重计mud tank 泥浆罐multip le comple tion多层完井MW(mud weight) 泥浆重量,泥浆密度Nnail 钉子natura l flow 自喷NDBOPS(nipple down blowou t preven ters)卸下防喷器组NDT(nipple down tree) 拆卸井口装置，拆卸采油树near bit stabil izer金钻头扶正器neutro n 中子射线nipple down 卸下，拆卸nipple seatin g 座落接头no return未返回水泥浆normal circul ation正循环normal butane正丁烷normal pentan e 正戊烷nozzle size 水眼尺寸nut 螺母Ooff bottom不接触井底office办公室oil base mud 油基泥浆oil reserv oir 油层on bottom接触井底open 打开open hole 裸眼openin g 扩眼o-ring O环outer barrel外岩心筒oven 烘箱over pullin g 遇卡oversh ot 打捞筒Ppacker封隔器packin g 密封圈paint油漆panel面板paraff in pluggi ng 蜡堵paraff in valve清蜡闸门paraff in-treatm ent 清蜡处理paraff in-troubl es 结蜡井parts零件pentan e 戊烷PH contro l additi ve PH控制剂phenol phtha lein酚酞pile hammer打桩机pin 销子,公扣pincer s 钳子pipe wrench管子扳手piston活塞piston rod 活塞杆pit drill防喷演习pit level泥浆液面pit level泥浆池液面pit volume increa se 泥浆增加量plasti c viscos ity 塑性黏度plug 水泥塞plug contai ner 水泥头plug flow 塞流pluggi ng back cement ing 回堵注水泥pollut ion 污染polyme r 聚合物portla nd cement硅酸盐水泥potass ium chlora te 氯化钾powerslip 动力卡瓦power source电源power swivel动力水龙头powertong 动力大钳powerlaw model幂律模型pressu re declin e 压力降pressu re equili brium压力平衡pressu re gage 压力表pressu re gradie nt 压力梯度pressu re gradie nt 压力梯度pressu re loss 压力损失pressu re loss in pipe 管内压力损失pressu re of mud column泥浆柱压力pressu re loss in annula r 环空压力损失pressu rized air 压缩空气preven ter of double ram type 双闸板式防喷器produc tion生产propan e 丙烷pry bar 撬杠，杠杆pull out of the hole 起钻pulley滑轮pulley滑轮pullin g slip 起卡瓦pumice浮石pump count累计泵冲数pump effici ency泵效pump pressu re 泵压pump speed泵速pump stroke counte r 泥浆泵冲数pup joint短接put into gear 挂挡put on break刹车，制动PWV(produc tionwing valve)生产翼阀Qquickcoupli ng 快速接头，快接管箍Rradiooperat or 电报员radioa ctivi ty log 放射性测井rag line 大棕绳rain densit y 颗粒密度rat hole 鼠洞rate of penetr ation转速reamer释放，丢手reamin g 辊轴扶正器record er 划眼red lead 记录仪reduce r 丝扣油，铅油，管件润滑油regula r 大小头releas e 正规扣relief valve泄压阀,泄流阀reserv e pit 储存池reserv oir pressu re 油层压力retard er 缓凝剂return返回水泥浆return mud 反出泥浆return ing fluid井口反出液revers e circul ation反循环revers e circul ation反循环revolu tion运转revolu tion转数revolu tions per minute每分钟转数Reynol ds number雷诺数rig down 拆卸钻机rig up 安装钻机rig in 安装,连接rig out 拆卸ring gasket钢圈/垫圈riser隔水导管rope damp 绳头,绳卡rotary hose 泥浆水龙带rotary slip 转盘卡瓦rotary speed转盘转数rotary table转盘rotati on bases倒班roughn eck 钻工rousta bout水手run casing下套管run in the hole 下钻run length进尺run bridge plug 下桥塞run gaugecutter通井runnin g tool 下入工具runnin g in test 试车runnin g repair日常修理,现场维修RWTO(return ed well toproduc tion)井恢复生产Ssafety belt 安全带safety clamp安全卡子safety joint安全接头safety valve安全阀sampli ng depth取样井深sampli ng interv al 取样间隔sand bridge砂桥sand troubl e 砂堵sandli ne 捞砂绳satura ted salt-watermud 饱和盐水泥浆screw螺钉seal 密封/封堵seatin g nipple座落接头sea-watermud 海水泥浆sensor传感器separa ter 分离器set back 立根盒settin g slip 放卡瓦shaft轴shale shaker振动筛shallo w gas 试气层shearrate 剪切速度shearpin 剪切销钉sheave滑轮shocksub 减振器shoe guide引鞋shorttrip 短起下钻shut in 关井shut in casing pressu re 关井套管压力shut in drillpipe pressu re 关井钻杆压力shut in pressu re 关井压力shut off 关闭side wall neutro n log 井壁中子测井silico n flour硅粉silico n-contro lledrectif ier 可控硅整流器single joint elevat or 单根吊卡single ram 单闸板slip 卡瓦slip type elevat or 卡瓦式吊卡slip veloci ty 沉积速度slip workli ne 倒大绳slow pump 低泵速sludge tank 加重泥浆池slushpump 泥浆泵socket插座solid conten t 固体含量soniclog 声波测井sonicwave 声波spacer隔离液spare parts备件spider卡盘sponta neous potent ial log 自然电位测井spool四通spring弹簧spud in 开钻squeez e cement ing 挤水泥stabil izer扶正器stabil izing agent稳定剂stage cement ing 分级注水泥stainl ess steel不锈钢stand立柱standpipe 立管standthe test 试验合格,经受考验standb y 待机stand-by boat 值班船starti ng outfit启动设备static pressu re 静压steam蒸气sticki ng 卡钻/被卡stinge r 导向插头,引鞋,尾管stinge r sub 插入式短节stop lost circul ation堵漏storm风暴straig ht well 直井眼sub 接头,短接submer ged pump 潜水泵substr uctur e 井架底座suckin g line 上水管线suctio n tank 吸入池superc harge pump 泥浆灌注泵superv isor监督supply boat 供应船suppor t 支架surge pressu re 冲击压力suspen dingweight悬重swab pressu re 抽吸压力swabbi ng 抽吸switch开关TT/B/G 牙齿/轴承/外径磨损table torque meter转盘扭矩表tableheight转盘高度taper millin g 锥形刮刀techni cian技术人员，技师tee 三通temper ature log 温度测井ten minute s gel 终切test paper试纸thread丝扣tie back tool 回接工具tighte n 上紧。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Drilling 钻井Casing and Cementing 下套管与固井Fishing 打捞Coring 取芯Freeing Stuck Pipe 卡钻与解卡Abnormal Well Condition and Well Control异常井况与压井BOP and subsea Equipment 防喷器与水下设备Safety and Firefighting 安全与消防Repair and Maintenance 检修Miscellaneous 其他附录一: 平台人员岗位名称附录二: 平台主要设备附录三. 平台场所附录四. 钻具,井口工具,打捞工具附录五. 材料和工具Drilling 钻井1.Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业.2.Prepared bell nipple. 准备”喇叭口”短节.3.Make up 2 joints of drill pipe. 接两根钻杆.4.Break out this connection. 卸开该接头.5.Run hole opener to sea bed. 下扩眼器到海底6.Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆.7.Make up bottom hole assembly. 组合下部钻具8.Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.9.Number stands on trip out and trip in. 起下钻时给立柱编号.10.Pick up BHA and run to seafloor. 将下部钻具下到海底.11.Pick up stands. 接立柱12.Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱13.Drop TOTCO. 投(陶特)测斜仪14.Fish TOTCO with overshot. 用打捞筒捞起测斜仪15.Resume drilling to T.D. 继续钻进到总深16.Circulate 15 minutes.循环15分钟17.Run in hole. 下钻18.Put out of hole. 起钻19.Make an inventory of all ring gaskets. 开一个所有垫圈的清单e spinning tong. 使用气动扳手21.Operate the air winch. 操作气动绞车y down 57 joints of 5” drill pipe. 甩57根钻杆23.Pick up drill stem test tool. 提起钻杆测试工具24.Circulate mud for 2 hours. 循环泥浆2小时25.Move string during circulation. 在循环时注意活动钻具26.Circulate hole clean. 循环清洗井眼27.Circulate bottoms up. 循环泥浆几周28.Fill up every 5 stands. 每5柱灌泥浆一次29.Check mud weight every 15 minutes. 每15分钟检查泥浆比重30.Reverse out excess cement. 反循环替出多余的泥浆31.Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆32.Stop drilling. 停止钻进33.Drilling ahead. 钻进34.Pull out of hole bit. 起出钻头35.Change bit. 换钻头36.Run the wear bushing. 下抗磨补心37.The bit thread type is regular pin. 钻头丝扣是正规公扣38.What’s the make-up torque? 上扣扭矩要多大?39.Run in 9” collars. 下9”钻铤40.The cathead can’t give enough torque. 猫头力量不够41.Connect crossover sub. 接上配合接头42.The tong angle is too small. 大钳的角度太小了43.Stop circulating. 停止循环泥浆44.Break out the stand. 卸立柱45.Set the single into the mousehole. 把这个单根放进鼠洞46.Can we break out the pipe with rotary table? 可用转盘卸扣吗?47.No! Break it out with tong. 不行! 要用大钳卸扣48.Spin it out with the air spanner. 用气动扳手卸扣49.Put the pipe wiper on the string. 装上钻杆刮泥器50.Don’t set this stand back. 这根钻杆不要放在钻杆盒上51.Make up the lift sub. 接好提升短节52.Secure the safety clamp. 上紧安全卡瓦53.The bit is nearing the shoe. 钻头快到套管鞋了54.Slow down the running speed. 放慢下放速度55.This is the under gauged interval. 这是缩径井段56.This is the drilling program. 这是钻井设计书57.How much weight on bit is required? 要加多少钻压?58.Keep the rotary speed at 120---140 RPM. 转速保持120---140转/分59.Keep the flow rate at 3000 LPM. 保持排量3000升/分60.The pump pressure is too high. 泵压太高了61.Don’t ream the hole too fast. 划眼不要太快62.Notice the rotary torque. 注意转盘扭矩的变化63.The penetration rate is getting slower. 钻速变慢了64.The bit is nearly worn out. 钻头快磨光了65.Stop drilling at 2000 meters. 钻至2000米停钻66.Circulate for one hour. 循环一个小时67.The pump pressure has increased. 泵压升高了68.One nozzle may be plugged. 可能有一个水眼(或: 喷嘴)堵了69.What is the hook load? 悬重多少?70.What’s the pick-up weight? 上提重量是多少?71.What’s the lowering weight? 下放重量是多少?72.Run in HWDP. 下加重钻杆73.A stabilizer is needed here. 这里需要一个扶正器74.This is a flexible sub. 这是挠性接头75.This is the BHA log. 这是下部钻具组合记录76.Record all outside and inside diameters. 记录好所有(入井工具的)内外径77.We need a short drill collar. 需要一根短钻铤78.Pull the cat line. 拉猫头79.Operate the break lever. 操作(或:扶)刹把80.Stop the pumps. 停泵81.Make a wiper trip. 通井82.Retrieve wear bushing. 取出抗磨补心83.Bleed off pressure. (释)放压(力)84.Keep 5 wraps on the drum. 滚筒上留5圈85.Set slips. 座上卡瓦86.If tight hole, repeat wiper trip. 如果井眼紧, 重复划眼87.Setback bottom hole assembly. 将下部钻具立于钻杆盒内88.Make sure all alarms are on. 确保所有的警报信号都开着y down TDS spinner. 拆下顶部驱动的旋扣器90.Run in hole bit #15 to bottom. 用15号钻头下钻到井底91.Run in hole to casing shoe. 下钻至套管鞋92.Pick up same bit and BHA. 装上同样的钻头和钻具组合y down 5” HW drill pipe. 甩5”加重钻杆94.Move string every 2 hours. 每2小时活动钻具一次95.Keep area around shaker clean. 保持振动筛区域干净96.Control trip gas. 控制起下钻气97.Ream if needed. 如必要时进行划眼98.Select the best penetration rate. 选择最佳钻进速度99.Fix the traveling assembly. 固定游动系统100. Check power tongs and spinning rope are on drill floor. 检查动力钳和尾绳是否在钻台100.What’s the weight on bit? 钻压是多少?101.What is the BHA of this well? 这口井的下部钻具如何组合?102.Drill out cement. 钻穿水泥103.Drill out 20” casing shoe. 钻穿20”套管鞋tch the elevator. 扣吊卡105.Unlatch the elevator. 开吊卡106.Set the slips. 放卡瓦107.Adjust the crown-o-matic (crown saver). 调整防碰天车108.Lock the hook pin. 锁紧大钩销子109.Check OD of stabilizer. 检查扶正器的外径110.Perform leak off test. 进行地层破裂(或:渗漏)测试111.Connect kill and choke line. 接上压井和放喷管线112.Reverse out the drill pipe. 反循环清洗钻杆113.Make a short trip. 进行短途起下钻114.Change the cutters. 换割刀115.Slug the pipe. 灌重泥浆116.Drill the stand down. 钻完立柱117.Start/run the shale shaker. 开振动筛118.Start the desanders. 开除砂器119.Start the desilters. 开除泥器120.Change it with a 40 mesh screen. 换成40目筛布121.Shut it off. 关掉122.Pull it to the cat ramp. 把它拉到坡道上去123.Make a fast connection. 接单根要快124.Don’t dump the mud into the sea. 不要把泥浆排放到海里125.Disconnect it with a chain tong. 用链钳卸开126.Put a thread protector. 加一个(丝扣)护箍127.Can we use the power slips? 可以使用动力卡瓦吗?Casing and Cementing 下套管与固井128.Run in hole to bottom for wiper trip. 下钻通井129.This is the casing program. 这是套管程序130.Prepare for running casing. 准备下套管131.Make everything ready for running 7”casing. 做好下7”套管的准备132.Make cementing job. 固井133.Displace cementing with mud pump. 用泥浆泵替泥浆134.Set cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞135.Pick up cementing head. 接水泥头136.Cement samples are hard. 水泥样已凝固137.Pump in 3 cubic meters of spacer. 注3方隔离液138.Pump down the plug. 泵压(胶)塞139.Wait on cement. 候凝140.The guide shoe will be connected. 接引鞋141.Connect the floor collar. 接浮箍142.Connect the air line to the casing stabbing board. 接好套管扶正台的气管线143.Run casing with the 350T slip elevator. 用350吨卡瓦式吊卡下套管144.Clean and dry 20” casing threads with rags. 清洁并擦干20”套管丝扣145.Where is the rabbit for drifting the casing? 套管通径规在哪里?Rig Move, Anchoring and Positioning 拖航, 抛锚, 定位146.What is our position now? 我们现在船位在哪里?147.What’s the moving speed now? (What’s the towering speed?) 拖航速度是多少?148.The speed is about 4 knots. 船速是4节左右149.Which one is the main tug? 主拖是哪条船?150.The main tug is Nanhai 205. 主拖是南海205151.Which one is the chase boat? 护航船是哪一条?152.How much is the horse power? 有多大马力?153.She has 6000 HP. 有6000马力154.Move the rig off location 50 feet. 将平台移开50英尺155.We are ready to drop the anchor. 我们已经做好抛锚的准备了156.Secure all the movable equipment. 固定好各种活动的设备157.Preload. (自升式)压载158.Ballast. (半潜式)压载159.Put the preload water into the tank. 向压载舱灌压压载水160.We need 5500 tons of preload water. 需要5500吨压载水161.Shall we preload right now? 马上开始压载吗?162.Drain the water off. 放水163.The rig is overloaded. 平台已超载164.Jack up (jack down) the rig. 升(降)船165.The draft is 3.5 meters. 船体吃水3.5米166.The jetting pressure is 100psi. 冲桩压力是100psi167.Penetrate the legs. 插桩168.How much penetration do we have? 入泥多深了?169.No.1 and No.2 legs indicate 10 meters. 1,2号桩腿插入10米170.Fix the upper and lower wedges. 固定上下楔块171.Pay out the anchor line. 放出锚缆绳172.Skid the derrick. 移开井架173.The rig is short of potable water now. 平台缺乏饮用水174.Drop No.2 and No.3 anchors. 抛2号和3号锚175.Why has the main engine stopped? 主机为什么停?176.Unleash the drilling tools. 卸开钻具177.Tighten up. 绷紧(或:上紧)一点178.Turn on the cooling water for the windlasses. 开锚机刹车冷却水179.Retrieve the No.1 to No.8 anchors. 起1到8号锚180.Check the paint marks at the anchor winches. 检查锚机上的油漆记号181.Prepare for a location move. 准备好移井位mence anchor handling. 开始起锚(或抛锚)183.Secure all equipment stored on deck. 固定好所有存放在甲板上的设备184.Carry out stability and load calculations. 做稳性和载荷计算185.Pass pendant line, shackle and buoy to anchor handling vessel. 将起抛锚短索, 卸扣和浮标吊起给起锚船186.Lower the windward anchor to seafloor. 抛上风锚到海底187.Pick up the leeward anchor first. 先起下风锚188.Take anchor chaser (or chaser) back to rig. 将捞/抛锚环送回平台189.Hook up towing lines to tug boat. 将拖缆连接到拖轮190.Sound fog signal for two seconds every twenty seconds. 发大雾信号, 每20秒钟响两秒Fishing 打捞191.The bit cutters have been lost in the hole. 牙轮落井192.Run in the reverse-circulation basket. 下反循环打捞篮193.There is a lot of junk in the hole. 井下有很多落物194.The fish is 235.46 meters long. 落鱼长度235.46米195.The fish top is at 2478.34 meters. 鱼顶位置2478.34米Coring 取芯196.Stop drilling for coring. 停钻准备取芯197.Make up core bit. 接取芯钻头198.What type of core bit is it? 这是什么型号的取芯钻头?199.Run in a diamond core bit. 下金刚石取芯钻头200.Let’s drop the ball for coring. 可以投球取芯201.The core has been broken off. 岩芯断了202.Put the core in the boxes. 把岩芯装在岩芯盒里203.Don’t brake suddenly. 不要猛刹车204.Take out the core. 岩芯出筒205.How long is the core? 岩芯多长206.The core recovery is 98%. 岩芯收获率是98%207.Run in the core barrel again. 继续下岩芯筒(或: 取芯筒)208.Run in hole core barrel. 下取芯筒209.Drop ball. 投钢球210.Recover core. 取出岩芯e same parameters as for core #1. 使用与1#取芯同样的参数Freeing Stuck Pipe 卡钻与解卡212.The down-hole problems are very complicated. 井下情况很复杂213.The hole is tight. 遇阻了214.Overpull while tripping out. 起钻遇卡(overpull: 超拉力)215.The formation is unstable. 地层不稳定216.The wall caving is severe. 井壁垮塌严重217.There are many return cuttings. 返出岩屑特别多218.The mud returns have decreased. 返出泥浆减少219.The hole is enlarged. 井眼扩大了220.The pipe’s stuck.卡钻了221.Pull up to 150 tons. 上提150吨222.Slack off to 50 tons. 下放至50吨223.Ream down all the tight points. 在所有遇阻点进行划眼224.The rotary table can’t rotate. 转盘转不动225.Where is the sticking point? 卡点在哪里226.Make a tensile test. 做拉伸试验227.Back it off above the free point. 在卡点以上倒扣228.Where is the back-off position? 脱扣位置在哪229.Plug the well for side tracking. 打水泥塞侧钻Abnormal Well Condition and Well Control异常井况与压井230.The mud is gas out. 泥浆有气侵231.The pit has lowered quickly. 泥浆池液面下降很快232.The hole lost returns. 井口不返泥浆233.The returns are unstable. 返出泥浆量忽大忽小234.Where’s the thief zone? 漏失层在哪里235.Cut down the flow rate. 降低排量236.Lower the mud density. 降低比重237.Cut down the hydrostatic pressure. 减少静压238.The gas smell is strong. 天然气味度很浓239.There’s some trace of oil. 发现有油花240.The pump pressure is fluctuating. 泵压不稳241.It is a zone of abnormal pressure. 这是异常压力层242.The hole (well) is kicking! 井涌啦!243.Shut in the BOP! 关闭防喷器244.Sound the general alarm quickly! 快发出综合警报245.The stand pipe pressure is 10 kg/cm2. 立管压力10公斤/厘米2 246.The casing pressure is 25 kg/cm2. 套压2510公斤/厘米2247.Fill out the kill sheet. 填写压井记录表248.Kill the well. 压井249.There’s a combination of lost returns and the kick. 又喷又漏, 情况复杂250.Reverse the gas out of the hole. 反循环排气251.What’s the lag time? 迟到时间是多少252.The well is now stable. 现在井眼已经稳定BOP and subsea Equipment 防喷器与水下设备253.Cut off the 30” conductor. 割掉30”隔水管254.Weld on the 30” bottom flange. 焊接30”法兰255.Hoist and nipple up 30” diverter. 吊装30”转喷器256.Change the 5” pipe rams to 3-1/2” rams. 把这个5”闸板换成3-1/2”257.Install blind ram. 安装防喷器的盲板芯子258.Check the seal ring of the conductor. 检查隔水管密封圈259.Cut off the lifting eye of the conductor. 切割隔水管耳环260.Test BOP. 测试防喷器261.Change annular BOP packing. 更换万能防喷器芯子262.Full pressure test the ram preventers. 对闸板防喷器进行全压试压263.Test annular BOP at 2500psi. 万能防喷器试压至2500psi264.Check annular pressure. 检查环形空间压力265.Confirm the angle of the guide base. 确定基板角度266.The thread is covered with the quick-release protectors. 已戴好快卸护丝267.Establish the guide lines. 装导向绳268.Connect the TGB running tool. 接临时导向基板送入工具nd the TGB to sea. 下临时导向基板到海底270.Retrieve the running tool. 退出送入工具271.Run the BOP and risers. 下防喷器和隔水管272.Pick up the marine riser. 吊出隔水管273.Pick up the slip joint. 起伸缩节274.Adjust the riser tensioners. 调整隔水管张力275.Function test the diverter system. 对防喷器系统进行功能测试276.Retrieve the pin connector. 取出销钉连接器277.Move the BOP to the moonpool door. 将防喷器移到园井甲板的活动门上278.Run the test plug. 下试压塞279.Close the upper pipe ram. 关上部钻杆闸板防喷器280.Open the kill line valve. 开压井管线阀281.The compensation capacity is 400000 pounds. 补偿能力是400千磅282.The locking load is 1000000 pounds. 锁紧负荷1000千磅283.Support the riser. 接隔水管支撑环284.Remove the hose bundles. 卸下垮接软管285.Assure the self-controlled rotation. 保证自控转动286.Set the LMRP on the test pump. 将下部防喷器插入总成座放到试压桩上287.Connect the flex joint to the riser. 连接隔水管与挠性接头nd the BOP onto the well head. 座防喷器到井口头289.Run the subsea TV for monitoring. 下水下电视观察290.Remove all the riser running tools. 取出所有的隔水管送入工具291.BOP carrier. 防喷器叉车292.Lower the universal guide frame. 下放万能导向架293.Paint mark the top 6 meters of 30” conductor white. 在30”隔水管的顶部6米处用白漆涂上记号294.Check adequate length for guidelines. 检查导向绳的长度是否足够295.Move temporary guide base (TGB) into moonpool. 将临时导向基板到园井甲板296.Test pull to check connection. 试拉检查连接297.Grease TGB and running tool as required. 按要求给导向基板及下入工具上黄油298.Test fit TGB and running tool. 用下入工具试临时导向基板连接299.Check for junk inside shoe joint. 检查浮鞋内有无落物300.Pick up 30” conductor handling slings and shackles. 吊上下30”导管的索具和卸扣301.Is slope indicator properly mounted? 水平仪是否装好?302.Ensure subsea TV is in good condition. 确保水下电视处于良好的状态303.Place BOP stack on the test pump. 将防喷器组放在试压桩上304.Check condition of all 30” casing connectors. 检查所有30”套管接头的情况305.Replace O-rings as required. 按需要, 更换O性密封圈306.Attach slope indicator below camera position. 在摄像机下面装上水平仪307.Inspect and repair diverter. 检查并修理转喷器308.Prepare spud plate and wireline to check water depth. 准备测深板和钢丝绳测量水深309.Record all pressure tests on a chart recorder. 用试压表记录试压记录310.Visually inspect all sealing element. 目视检查所有密封件311.Check and tighten all bolts. 检查并上紧所有螺栓312.Bleed off surface accumulators. 地面管线排空气313.Check for leaks. 检查有无泄漏314.Lift BOP stack and replace wellhead connector AX ring. 吊起防喷器组并更换连接器AX密封圈315.Function test wellhead. 对井口头进行功能试验316.Fill kill and choke valves with seawater. 将压井阀和阻流阀注满海水317.Pressure test to 500psi then bleed off test pressure. 试压到500psi, 然后放掉压力318.Reduce hydraulic control manifold pressure to 5200 kpa. 将液压控制管线压力减少到5200千帕319.Switch to alternate control pod. 把闸门开关倒到控制面板320.Guidelines are slacked off. 导向绳松了321.Slack off drill pipe and release running tool. 放松钻杆并卸开下入工具322.Run subsea TV to observe bit entering the TGB. 下水电视观察钻头是否进入临时导向基板323.Don’t rotate until hole opener passes through the TGB. 在扩眼器通过临时导向基板前不要旋转324.Position permanent guide base (PGB) below rotary table. 在转盘下安放永久导向基板325.Monitor riser level via trip tank. 用计量罐来控制隔水管内的液面326.Pressure test to 5000psi. 试压5000psi327.Pick up test mandril and place in BOP. 吊起试压防喷器芯子并装入防喷器组328.Safety and Firefighting 安全与消防328.Get a Work Permit before you can start the hot work. 办理作业许可证才能进行动火作业329.Welding is not allowed. 不准动焊330.Put on your (safety) helmet. 戴上安全帽331.It’s a high voltage area. 这是高压区332.That’s against the rule. 这是违章作业333.Don’t walk under the crane load. 不要在吊物下走动334.The repairing is under way. 正在检修335.Keep your hands clear! (Keep you hands off! Do not touch!) 不要乱动336.Wear and secure your safety belt. 戴上并系好安全带337.Life jacket must be worn when working outboard or overhead.舷外或高空作业要穿救生衣338.Have your breathing apparatus near you. 保持放毒面具在附近339.It’s a drill. 这是演习340.It was a BOP drill. 这是防喷演习341.Get in the lifeboat in order. 按顺序进入救生艇342.Put on life jacket! 穿好救生衣343.Abandon the vessel! 弃船344.Sound the abandonment alarm! 发出弃船警报345.Go to the helideck! 去飞机坪集合346.Aboard the lifeboat. 登上救生艇347.Aboard the supply boat to shore! 乘拖船上岸348.Check life saving apparatus periodically. 定期检查救生设备349.It’s for fire fighting. 这是消防用的350.Start the fire pump. 启动消防泵351.This rope is too small. 这根绳子太细了352.It should be function tested. 需做功能测试353. A warning notice should be set up. 要挂警告牌354.Do you have an emergency program (contingency plan)? 你们有没有应急计划?355.It must be ready in an emergency condition. 必须始终保持良好的应急状态356.Will the typhoon hit our rig? 台风要袭击我们的平台吗? 357.We will have to evacuate the rig. 我们要撤离平台358.Personnel on board (POB). 在船人员总数359.Sound fire alarm. 发消防警报360.This is a fire drill. 这是消防演习361.conduct abandon ship drill. 举行弃船演习362.Release the boat hooks. 释放救生艇吊钩363.Board the life boat. 登救生艇364.Remove the rust and paint with anti-corrosive primer. 除锈后上防锈底漆365.Three rafts are located near life boat station port side. 在左舷救生艇站附近还存放有3个救生筏366.Wear work vests when working below the cellar deck. 在圆井甲板面下面工作时须穿工作救生衣367.The station bills need to be updated. 应急部署表须更新368.Check the expiry date for all foam extinguisher. 检查所有泡沫灭火器的过期时间369.Close all the water-tight doors. 关闭所有水密门370.Safety procedure shall be followed at all the times. 在任何时候都应遵守安全程序371.Anchor wires should have a Spelter type socket at anchor side.抛锚绳靠锚的一端应使用锌压头372.Colour code all the connection at the loading station. 在供给站管线接头处用颜色表明各管线373.Verify that a high level alarm is installed on the sludge tank. 确认污水舱安装有高位警报374.Don’t switch on during drilling operation. 钻井作业期间不能合闸375.Provide two independent means to start the emergency generator engine. 应急发电机柴油机应有两套独立的起动方法376.Have the boom pennant wires of port crane re-certified. 重新认证左舷吊车扒杆变幅绳377.Clean the internals of the emergency switchboard. 清洁应急配电盘内部Helicopter and Supply Vessel 直升机与供应船378.Load out Contractor’s riser at Zhanjiang anchorage. 在湛江锚地把承包商的隔水管装上平台379.Offload casing. (从供应船上)卸套管380.Load (offload or unload) the boat. 装(卸)船381.Get the food container loaded on the boat. 把食品集装箱装上船382.The helicopter will land on rig soon. 直升机很快就要在平台降落383.Tell the base to get (or send) a chopper here. 通知基地派飞机来384.Helicopters are not allowed to land here. 飞机不能降落385.Report the weather condition to the pilot. 向飞行员报天气rm the boat come to standby. 通知拖轮过来待命387.Call the boat to come along port side. 通知拖轮过来靠左舷388.We will take the personnel basket. 我们乘坐吊篮Repair and Maintenance 检修389.Have an overall check. 进行全面检查390.MPI the brake linkage system. 对刹车连接系统进行磁粉探伤391.Demonstrate that the make-up cathead can pull 7000 lbs. 证明上扣猫头能拉到7000磅392.Determine the origin of the air leak and rectify this. 找出漏气的地方并处理393.Adjust the brake band equalizer beam properly. 适当调整刹带平衡梁394.Note that the 3000 hour inspection on TDS is due. 注意顶驱的3000小时保养时间已到395.Check sheave rope pocket wear with a 1 3/8”+1 1/32 template.用1 3/8”+1/32”量规检查绳槽磨损的情况396.Repair the handrails on the crown. 修理天车台的栏杆397.Function test the anti-freefall brake on monthly basis. 每月对天车防碰装置进行功能试验398.Get me a spanner, please. 请递给我一把扳手399.Renew brake rim because of excessive wear. 更换磨损严重的刹车鼓400.Clearly mark safe working load (SWL) on the air winch below the rig floor. 表明钻台底下气动绞车的安全工作负荷401.Measure the master bushings for wear. 测量主补心磨损情况402.Have BOP ram opened up for internal inspection. 打开防喷器闸板进行内部检查403.Install a ground cable on the triplex pump motor. 给三缸泵马达安装接地线404.We nee d a 48” pipe wrench. 我们需要一把48”的管钳405.Strike it with a sledge hammer. 用大锤打406.We want a triangle file. 需要一把三角锉刀407.Tighten up the screw. 紧一下螺丝408.Check it with a level. 用水平尺量一下409.Put some engine oil. 抹点黄油410.Have it greased. 给它上黄油411.Put out of hole test string. 取出测试管串412.Check all the equipment. 检查所有设备413.There’s something wrong with it. 有点毛病414.Rig inspection will be performed in August. 验船安排在8月份415.Maintain the hoisting system. 保养提升系统416.Adjust the brake band. 调整绞车刹带417.Change the oil in the rotary gear box (transmission). 更换转盘变速箱机油418.Replace one water pump. 倒换一台冷却泵419.It’s quick-discharge air valve. 这是快速放气阀420.This clutch needs repair. 这台离合器需修理421.This tong needs replacing. 这把钳要更换了422.Slip 6 meters of the drilling line. 滑移钻井大绳6米423.Cut off 45 meters of the drilling line. 切割大绳45米424.Check the pump liners and pistons. 检查(泥浆)泵缸套和活塞425.The piston has been washed. 活塞刺坏了426.The supercharge pump doesn’t take in water. 灌注泵不上水427.Regulate the relief valve. 调整安全阀428.This part number is wrong. 这个配件号不对429.The multi-pen recorder has some problem. 多笔记录仪坏了Miscellaneous 其他430.No smoking here. 此处严禁吸烟431.Everything is OK. 一切准备就绪432.Speed up please. 请快点433.The geologist must be present. 地质人员必须到场434.We have to wait on weather. 必须等候天气435.There will be strong wind. 有强风436.Give me a hand, please. 请帮一下忙437.Do you understand? 明白吗?438.No way! 不行439.Man overboard! 有人落水440.Help! Help! 救命441.Someone is injured. Medic! 有人受伤了, 医生442.Call for the medic. 叫医生443.Get a stretcher please. 拿担架来444.No more than 4 persons. 不能超过4人445.Drinking liquor is not allowed. 不许喝酒446.Don’t overrun your equipment. 不要超负荷运转447.Be careful at work. 工作时要小心448.No joking here. 别开玩笑449.Rig up for logging. 准备电测450.What is the next step? 下一步怎么办?451.Get everything ready as soon as possible! 尽快做好一切准备附录一: 平台人员岗位名称一. 承包商人员( Contractor’s Personnel )Rig Manager 平台经理Equipment Supervisor 设备总监Materials Supervisor 材料总监Senior Toolpusher 高级队长Junior Toolpusher 值班队长Driller 司钻Sub Sea Engineer (SSE) 水下工程师Assistant Driller (AD) 副司钻Derrick Man 井架工Floor Man (roughneck) 钻工Barge Master (captain) 船长First Mate (Barge engineer) 大副Control Room Operator (CRO) 压载工Ballast Control Operator (BCO) 压载工Chief Engineer 轮机长Head of Roustabout甲板班长Crane Operator 吊车工甲板工RoustaboutMechanic 机械师Electrician 电气师Repairman 修理工maintenance man Motorman 轮机员Welder 焊工Radio Operator 电报员Warehouse Man (stock Keeper) 材料员Medic 医生Safety Supervisor 安全监督Interpreter (translator) 翻译Chief Steward 管事Cook 厨师Steward 厨工Laundry Man 洗衣工二. 作业者及服务公司人员( Operator’s Personnel and Service CompanyPersonnel)Drilling Superintendent 钻井监督Company Man (Op erator’s Representative) 公司代表Geologist 地质师Mud Logging Engineer (Mud logger) 泥浆录井工程师Sample Catcher 捞砂工Mud Engineer 泥浆工程师ROV Engineer 潜水工程师Cementer 固井工Cement Engineer 固井工程师Testing Engineer 试油工程师Coring Engineer 取芯工程师Wireline Logging Engineer电测工程师附录二: 平台主要设备一. 钻井设备 (Drilling Equipment):Draw works 钻井绞车Rotary Table 转盘Bushing 补心Top Drive System (TDS) 顶驱Swivel 水龙头Crown Block 天车Traveling Block 游车Hook 大钩Derrick 井架Pipe Spinning Wrench 钻杆气动扳手Ezy-Torq 液压猫头hydraulic cathead Elmagco Brake 涡磁刹车Pipe handling Equipment 钻杆移动设备Iron roughneck 铁钻工Pipe Racking System 钻杆排放系统Drill String 钻柱Drilling Sub 钻井短节Fishing Tool 打捞工具Power Tong 动力大钳Air Winch (air tugger) 气动绞车Crown-O-Matic (Crown Saver) 防碰天车二. 泥浆系统 (Mud System)Mud Pump 泥浆泵Shale shaker 振动筛Mud Cleaner 泥浆清洁器Desilter 除泥器Desander 除砂器Degasser 除气器Centrifuge 离心机Mud Agitator 泥浆搅拌器Mud Mixing System 泥浆混合系统Centrifugal Pump 离心泵Standpipe Manifold 立管管汇Rotary Hose 水龙带Bulk Air System and Tank 吹灰系统和灰罐三. 井控设备 (Well Control Equipment): Ram Type Preventer 闸板防喷器Annular Type Preventer 万能防喷器BOP Stack 防喷器组Gate Valve 闸阀Choke and Kill Manifold 阻流压井管汇Remotely Operated Panel 远程控制面板Choke Control Panel 阻流控制面板BOP Handling Equipment 防喷器搬运设备Diverter 转喷器四. 海事系统 (Marine System)Ballast System 压载系统Bilge System 污水系统Vent 通风口, 通气口Air Supply Fan 供气扇Mooring System 锚泊系统Communication Equipment 通讯系统Jacking System 升降系统Skidding System 井架滑移系统Windlass 锚机Anchor 锚Pendant 短索Buoy 浮标Lifting and Handling Equipment 起吊和搬运设备五. 机房 (Engine Room)Diesel Engine 柴油机Emergency Generator 应急发电机Water Maker (desalinization unit) 造淡机Air Compressor 空气压缩机Boiler 锅炉Air-conditioning System 空调系统Sea Water Service Pump 海水供给系统Piping System 管汇系统Generator 发电机Transformer 变压器DC Motor 直流马达AC Motor 交流马达六. 安全设备 (Safety Equipment)Fire Control System 消防控制系统Fire Detection System 火情探测系统CO2 System 二氧化碳系统Fixed Fire Extinguishing System 固定消防系统Portable Extinguisher 移动灭火器Fire-Fight Equipment 消防设备Foam System 泡沫系统Lifeboat 救生艇(Inflatable) Life Raft (气涨式)救生筏Davit 吊艇架Escape Routes 逃生路线Breathing Apparatus 呼吸器Life Buoy 救生圈Gas Detection System 气体探测系统Helicopter Facility 直升机设施Sick-Bay (Hospital) 医务室Pollution Control 防污控制七. 其他 ( Others)Cementing Unit 固井装置Well Testing Equipment 试油设备Mud Logging Unit 泥浆录井房Wire Logging Unit 电测装置ROV 潜水器Meter 米Foot 英尺Inch 英寸Supply Boat (supply vessel) 供应船Standby boat 值班船Day (night) Shift 白(夜)班Crew Change 倒班Crew 船员, 队员, 井队Position 岗位Draft (draught) 吃水Air Gap 空气间隙, 气隙Penetration (桩腿插桩)入泥Evacuation 撤离Rig (Drilling rig) 钻机, 钻井船附录三. 平台场所Bow 船首Stern 船尾Forward (FWD) or fore 船首的Aft 船尾的Port 左舷Starboard (STBD) 右舷Upper Deck 上部甲板Main Deck 主甲板Quarters (living quarters, accommodation area) 生活区Drill Floor (Rig floor) 钻台Bridge (Pilot house, Steerwheel house) 驾驶室Control Room 控制室Helideck 直升机甲板Cementing Unit Room 固井泵房Air Compressor Room 空气压缩机房BOP Control Room BOP控制房Radio Room 报房Engine Room 机房Thruster Room 推进器房Warehouse (Store) 材料库房Paint Room (paint locker) 油漆房库Leg 桩腿Jacking House 升降室Column 立柱Sack Storage Area 散装材料储存区Mud pit 泥浆池Cellar Deck 圆井甲板Riser Rack Area 隔水管排放区Pipe Rack Area 钻杆排放区Pipe Slide 滑道Ramp 坡道Spud Tank 桩脚箱Pontoon 浮箱Moon pool 月池/园井甲板Pump Room 泵房Shale Shaker House 振动筛房Coffee Room 咖啡室Rig Office 平台办公室Mess (dining) Room 餐厅Recreation Room 娱乐房TV RoomChange Room 工衣房Kitchen 厨房附录四. 钻具,井口工具,打捞工具Drill Pipe 钻杆Drill Collar 钻铤Heavy Weight Drill Pipe 加重钻杆Elevator 吊卡Tong 大钳Make-up Tong 上扣大钳Break-out Tong 卸扣大钳Mud Box 泥浆防喷盒Casing Stabbing Board 套管扶正器Slips 卡瓦Spider 卡盘Mouse Hole 小鼠洞 (接单根用) Kelly Spinner 方钻杆旋转器Kelly Cock 方钻杆阀Chain Tong 链钳Casing 套管Tubing 油管Drill String 钻柱Jar (drilling jar) 震击器Right Hand Thread 正扣Left Hand Thread 反扣Stabilizer 扶正器Rabbit 通管器Liner 尾管Conductor 导管Thread Protector 护丝Stand (钻杆) 立柱Single (钻杆) 单根Joint (钻具) 根Bend 弯头Sub 短节Pup Joint 短钻杆, 短节Connector 接头Bit 钻头Bit Breaker 钻头盒Box 母扣Pin 公扣Hole Opener 开眼钻头Reamer 扩眼钻头Overshot 打捞筒Junk Basket 打捞篮Junk Mill 平头磨鞋Spear 打捞矛Fishing Tap 打捞公锥Cross Over Sub (XO Sub) 转换接头Bottom Hole Assembly (BHA) 下部钻具组合。