ASTMA781报告模板

Brand: AUTOCARE
Weifang Fangda Material Co., Ltd
The West of Qianlou Village Zhuliu Subdistrict Changle County Weifang City Shandong Province, China
Made in China
P
If aminimum heat treatment temperature is not specified for thegrade, then the survey temperature shall be not more than 50°F(30°C) below nor more than 175°F (100°C) above the furnaceset point used.
P
4.2.3
The maximum variation in measured temperature asdetermined by the difference between the highest temperatureand the lowest temperature shall be as agreed between thepurchaser and producer except that during production heattreatment no portion of the furnace shall be below theminimum specified temperature nor above the maximumspecified temperature for the grade being processed.
Pass (P)
Test object does not meet the requirement ..:
Fail (F)
Testing:
Date of receipt of test item ….......................:
November01, 2018
Date(s) of performance of test ….................:
P
Samples for carbon analysis of carbon and alloy steel shall betaken no closer than 1⁄4 in. to a cast surface, except that castingstoo thin for this shall be analyzed on representative material.
Report Reference No.:
TCF-WFD-8948.08
Tested by (+ signature):
Kevin Ya3; signature):
King Hu
Date of issue:
November 19, 2018
Testing Laboratory:
“(see remark #)” refers to a remark appended to the report.
“(see Annex #)” refers to an annex appended to the report.
“(see appended table)” refers to a table in the Test Report.
P
The chemical composition thus determined shall meet therequirements specified in the applicable specification for thegrade involved, or shall be subject to rejection by the purchaser,except that the chemical composition determined forcarbon and low alloy steel castings may vary from the specifiedlimits by the amounts shown in Table 1.
P
The chemical composition thus determinedshall conform to the requirements in the individualspecification for the grade being poured.
P
5.3
Product Analysis—
P
The analysis shall be made from a test samplepreferably taken during the pouring of the heat.
P
When drillingsare used, they shall be taken not less than 1⁄4 in. [6.4 mm]beneath the surface.
-
4.1
Melting Process—
-
The steel shall be made by openhearthor electric furnace process with or without separaterefining such as argon-oxygen-decarburization (AOD) unlessotherwise specified in the individual specification.
November01, 2018 toNovember 19, 2018
General remarks:
The test results presented in this report relate only to the item(s) tested.
This report shall not be reproduced, except in full, without the written approval of the testing laboratory.
P
4.2
Heat Treatment
-
4.2.1
Castings shall be heat treated in the working zone of afurnace that has been surveyed in accordance with Test MethodA 991/A 991M.
P
4.2.2
When castings are heat treated at temperatures above2000°F (1100°C), then the working zone shall have beenestablished by a survey performed at not more than 25°F(15°C) below nor more than 200°F (110°C) above the minimumheat treatment temperature specified for the grade.
N/A
Model:
140*130, 333*333
Parameter:
-
Version
Version
Record
Version
Chapter
Date
Modifier
Remark
00
November 19,2018
Original
Copy of marking plate:
Pallet
Model 140*130, 333*333
P
The product analysistolerances of Table 1 are not applicable as acceptance criteriafor heat analysis by the casting manufacturer.
Commission Test
Non-standard test method…………..:
N/A
Test Report Form No.:
TRF Originator:
SBD
Master TRF:
Dated 2017-05
Test item description:
Pallet
Trademark:
NoMarking
Summary of testing:
The submitted samples were tested and found toCOMPLY WITHall clauses ofASTM A781 / A781M
Test Report Content
This test report consists of:
P
5.
Chemical Composition
-
5.1
Chemical Analysis—
P
Chemical analysis of materialscovered by this specification shall be in accordance with TestMethods, Practices, and Terminology A 751.
Address:
Testingprocedure:
Commission Test
Applicant’s name:
Weifang Fangda Material Co., Ltd
Address:
The West of Qianlou Village Zhuliu Subdistrict Changle County Weifang City Shandong Province, China