多功能表说明书
谐波多功能表使用手册说明书
用户手册User Manual谐波多功能表本设备只能由专业人员进行安装和检修。
对因不遵守本手册的说明所引起的故障,厂家将不承担任何责任。
危险与警告目录1 简介 (4)1.1概述 (4)1.2引用标准 (4)2 技术指标 (4)2.1基本参数 (4)2.2测量精度 (5)3 安装与接线 (6)3.1尺寸 (6)3.2间距 (6)3.3安装 (7)3.4接线端子排列 (7)3.5典型信号接线 (8)4面板说明与测量信息显示 (8)4.1 LED数码管显示 (8)4.2 LCD液晶显示 (10)5 编程设置 (11)6 通讯 (12)6.1特点 (12)6.2报文格式 (13)6.3通讯地址信息表 (15)7 其他功能模块 (19)7.1开关量输入 (19)7.2继电器输出 (19)7.3模拟量变送输出 (21)8 维护与故障排除 (23)8.1仪表的存储器 (23)8.2故障排除 (23)8.3服务承诺 (23)1 简介1.1概述谐波多功能电能表是高性能的监测仪表,用于配电系统的测量监视与控制,可真有效值测量三相电压、三相电流、有功功率、无功功率、视在功率、功率因数、频率、谐波,正反向有功/无功电能计量。
具有RS-485通讯、开关量输入、越限报警、遥控输出、模拟量变送输出和电能脉冲输出等功能。
谐波多功能电能表有着极高的性价比,可以直接取代常规电力变送器、测量仪表、电能计量表以及相关的辅助单元,应用领域非常广泛,如各种电力监控系统、工矿企业、公共设施、智能建筑和开关柜等。
1.2引用标准2 技术指标2.1基本参数2.2测量精度3 安装与接线3.1尺寸96规格3.2间距3.3安装安装该产品不需要专门的工具,它依靠2个固定卡架固定在安装屏上。
简单地,卸下2个固定卡架,将仪表插入为其打好的安装孔内,重新装配2个固定卡架,然后将它们紧紧按到薄金属板上,使之获得相应预紧效果即可。
3.4接线端子排列注意:根据具体型号和功能的不同,端子的配置会有所不同,用户在现场操作或者测试时,应当依据实物仪表上的端子铭牌进行线路连接。
PowerLogic PM5000系列基本多功能表计技术数据手册说明书
METSEPM5110METSEPM5330METSEPM5560PowerLogic PM5000 seriesTechnical datasheetBasic multi-function meters22013Functions and characteristicsP B 111776PowerLogic ™PM5000 Series meterPowerLogic ™ PM5100, PM5300 and PM5500 seriesThe PowerLogic ™ PM5000 power meter is the ideal fit for cost managementapplications. It provides the measurement capabilities needed to allocate energy usage, perform tenant metering and sub-billing, pin-point energy savings, optimize equipment efficiency and utilization, and perform a high level assessment of the power quality of the electrical network.In a single 96 x 96 mm unit, with a graphical display, all three phases, neutral and ground can be monitored simultaneously.The bright, anti-glare display features large characters and powerful backlighting for easy reading even in extreme lighting conditions and viewing angles.Easy to understand menus, text in 8 selectable languages, icons and graphics create a friendly environment to learn about your electrical network.Highly accurate devices with global billing certifications.ApplicationsCost management: Cost saving opportunities becomes clear once you understand how and when your facility uses electricity. The PowerLogic ™ PM5000 series meters are ideal for:• Sub billing / tenant metering: allows a landlord, property management firm,condominium association, homeowners association, or other multi-tenant property to bill tenants for individual measured utility (electricity) usage. MID approved meters for billing applications across Europe.• Cost allocation: allocate energy costs between different departments (HVAC,indoor and outdoor lighting, refrigeration, etc), different parts of an industrial process or different cost centres. Cost allocation systems can help you savemoney by making changes to your operation, better maintaining your equipment, taking advantage of pricing fluctuations, and managing your work management: Improving reliability of the electrical network is key for success in any business. Monitoring values such as voltage levels, harmonic distortion and voltage unbalance will help you to ensure proper operation andmaintenance of your electrical network and equipment. PowerLogic ™ PM5000 series meters are the perfect tool for:• Basic Power Quality monitoring: power quality phenomena can causeundesirable effects such as heating in transformers, capacitors, motors,generators and misoperation of electronic equipment and protection devices. • Min/ Max monitoring (with timestamp): understanding when electricalparameters, such as voltage, current and power demand, reach maximum and minimum values will give you the insight to correctly maintain your electrical network and assure equipment will not be damaged.• Alarming: alarms help you to be aware of any abnormal behavior on theelectrical network in the moment it happens.• WAGES monitoring: take advantage of the input metering on PM5000 metersto integrate measurements from 3rd party devices such as water, air, gas, electricity or steam, meters.Main characteristics Easy to installMounts using two clips, in standard cut out for DIN 96 x 96mm, no tools required. Compact meter with 72mm (77mm for PM5500) depth connectable up to 690 VL-L without voltage transformers for installations compliant with category III.Easy to operateIntuitive navigation with self-guided, language selectable menus, six lines, four concurrent values. Two LEDs on the meter face help the user confirm normaloperation with a green LED - heartbeat/communications indicator, and the amber LED - customizable either for alarms or energy pulse outputs.Easy circuit breaker monitoring and controlThe PM5300 provides two relay outputs (high performance Form A type) with capability to command most of the circuit breaker coils directly. For Digital Inputs, monitored switches can be wired directly to the meter without external power supply.PM5500 series have 4 status inputs (digital) and 2 digital output (solid state) to use for WAGES monitoring, control and alarm annunciation.Accurate energy measurement for precise cost allocation:32013Functions and characteristics (cont.)Direct metering of neutral currentThe PM5500 has a fourth CT for measuring neutral current. In demanding ITapplications, where loads are non-linear (i.e. switching power supplies on computers/servers), measuring neutral current is essential to avoid overload and resulting outage. In addition, the PM5500 provides a calculated ground current value, not available in meters with 3 CTs.Power Quality analysisThe PM5000 offers Total Harmonic Distortion (THD/thd), Total DemandDistortion (TDD) measurements and individual harmonics (odd) magnitudes and angles for voltage and current:These types of power quality parameters help to identify the source of harmonics that can harm transformers, capacitors, generators, motors and electronic equipment.Load managementPeak demands with time stamping are provided. Predicted demand values can be used in combination with alarms for basic load shedding applications.Alarming with time stampingA different combination of set point driven alarms and digital alarms with 1s time stamping are available in the PM5000 family:Alarms can be visualized as Active (the ones that have picked up and did not drop out yet) or Historical (the ones that happened in the past).Alarms can be programmed and combined to trigger digital outputs and mechanical relays (PM5300).The PM5000 series keeps an alarm log with the active and historical alarms with date and time stamping.Load timerA load timer can be set to count load running hours based on a minimum current withdraw, adjustable to monitor and advise maintenance requirements on the load.High Performance and accuracyIEC 61557-12 Performance measuring and monitoring devices (PMD)Defines the performance expectation based on classes. It defines the allowableerror in the class for real and reactive power and energy, frequency, current, voltage, power factor, voltage unbalance, voltage and current harmonics (odds), voltageTHD, current THD, as well as ratings for temperature, relative humidity, altitude, start-up current and safety. It makes compliant meters readings comparable - they will measure the same values when connected to the same load.Meets IEC 61557-12* PMD/[SD|SS]/K70/0.5 for PM5100 and PM5300Meets IEC 61557-12* PMD/[SD|SS]/K70/0.2 for PM5500Legal billing complianceMID compliance is compulsory for billing applications across Europe.In addition to billing applications, for facility managers responsible for energy cost MID means same level of quality as a billing meter.MID ready compliance, EN50470-1/3 – Class C *Pending approval.P B 111768P B 111770P B 111768PowerLogic ™ PM5500 meterPowerLogic ™ PM5300 meterPowerLogic ™ PM5100 meterBasic multi-function metering PM5000 SeriesFunctions and characteristics (cont.)42013Basic multi-function metering PM5000 SeriesFunctions and characteristics (cont.)52013Basic multi-function metering PM5000 SeriesFunctions and characteristics (cont.)*Electrical Characteristics still under verification at time of printing of the catalogue, may be subject to change.** PM5563 is DIN mounted*** Tests are conducted as per IEC 61557-12 (IEC 61326-1), 62052-11 and EN5047062013Basic multi-function metering PM5000 SeriesFunctions and characteristics (cont.)7201382013Basic multi-function meteringPM5000 SeriesDimensions and connectionPM5000 meter parts A Menu selection buttons B LED indicatorsC Navigation or menu selectionsD Maintenance and alarm notification areaPM5000 Series meter flush mounting*PM5000 Series meter dimensionsP B 111276P B 111279P B 111278P B 111277Please see the Installation Guidefor accurate and complete information on the installation of this product.PM5100 / PM5300 meter parts E Relay output (PM5300 only) F Voltage inputs G Control power H Current inputsI Status inputs/digital outputs J Communications port: Ethernet (PM5300 only) or RS-485)PM5100 / PM5300PM5500PM5500 meter parts E Voltage inputs F RS-485 comms G Digital inputs H Current inputs I Digital outputs J Ethernet ports K Control powerPM5500** PM5563 is DIN mountedA R T 059363 / © 2013 - S c h n e i d e r E l e c t r i c - A l l r i g h t s r e s e r v e dSchneider Electric Industries SAS 35, Rue Joseph Monier, CS 30323F - 92506 Rueil Malmaison Cedex RCS Nanterre 954 503 439Capital social 896 313 PLSED310052ENAs standards, specifications and designs develop from time to time, please ask for confirmation of the information given in this document.Design: Schneider Electric Photos: Schneider Electric07-201310-31-1247METSEPM5110METSEPM5330METSEPM5560。
华耐电气多功能表说明书
华耐电气多功能表说明书摘要:一、引言二、产品概述1.产品名称与型号2.产品功能三、产品结构与操作1.外观结构2.操作说明四、安装与接线1.安装环境2.接线步骤五、使用与维护1.使用注意事项2.维护保养六、技术参数1.电气参数2.环境参数七、产品配件与售后服务1.配件清单2.售后服务正文:一、引言华耐电气多功能表是一款具有高精度、多功能、易操作特点的电气测量仪表,广泛应用于工业、农业、商业等领域。
本文将详细介绍华耐电气多功能表的使用方法、功能特点、技术参数等内容,以帮助用户更好地了解和使用该产品。
二、产品概述1.产品名称与型号:华耐电气多功能表,型号为HN-MF01。
2.产品功能:华耐电气多功能表具有电压、电流、频率、功率、电能等多种测量功能,可满足用户对电气参数的监测需求。
三、产品结构与操作1.外观结构:华耐电气多功能表采用防水、防尘设计,表体为ABS 工程塑料,显示屏为LCD 液晶显示屏。
2.操作说明:用户可通过旋转开关、按键等方式进行操作,实现各种功能的选择与切换。
四、安装与接线1.安装环境:华耐电气多功能表适用于各种环境温度,安装时需避免阳光直射、潮湿、高温等恶劣条件。
2.接线步骤:用户需根据产品接线图正确接线,将红、黑、蓝三根线分别接到电源、负载和地线上。
五、使用与维护1.使用注意事项:在测量过程中,应确保表体与导线连接良好,避免短路、开路等现象发生。
2.维护保养:定期检查表体、导线接头等部件,保持清洁,发现问题及时处理。
六、技术参数1.电气参数:华耐电气多功能表具有较高的测量精度,电压、电流测量范围广泛。
2.环境参数:产品具有良好的抗干扰性能,能适应各种电磁环境。
七、产品配件与售后服务1.配件清单:产品附带说明书、合格证、保修卡等文件,以及红、黑、蓝三根接线线缆。
三相多功能表使用说明书
三相多功能表使用说明书一、产品概述本说明书旨在提供关于三相多功能表的使用说明。
该仪表是一种广泛应用于电力系统的测量设备,具有准确度高、稳定性好、功能丰富等特点。
通过本说明书,您将了解如何正确使用、安装、维护和故障排除三相多功能表,以确保其正常工作并提高测量精度。
二、型号与规格本产品型号为:XXXXXX主要技术参数:- 电压测量范围:XXX-XXXV- 电流测量范围:XXX-XXXA- 频率测量范围:XXX-XXXHz- 功率因数测量范围:-1-1- 精度等级:±0.5%- 工作温度:-20-70℃- 储存温度:-40-80℃- 重量:约+克- 尺寸:三、技术特性1. 高精度测量:采用先进的转换器和信号处理技术,实现电压、电流、频率、功率因数等参数的高精度测量。
2. 宽量程范围:适用于不同规模和类型的电力系统,能够准确测量大范围变化的电量参数。
3. 可靠性与稳定性:采用高质量的电子元件和材料,经过严格的质量控制和环境测试,确保长期稳定运行。
4. 多功能显示:具有大屏幕液晶显示界面,可以同时显示多个电量参数和统计数据。
5. 数据存储与导出:内置大容量存储器,可以存储大量的历史数据和事件记录,可通过通讯接口导出至计算机进行进一步分析。
6. 远程控制与通讯:支持多种通讯协议,可以通过RS485、以太网等接口与远程监控系统连接,实现远程控制和数据传输。
7. 防雷与浪涌保护:内置浪涌保护电路和防雷元件,有效防止雷电对仪表的损害。
8. 安装便捷:提供多种安装方式,可以固定在盘柜上或安装在导轨上,方便用户灵活配置。
四、安装与连接1. 安装位置:选择一个合适的位置来安装三相多功能表,确保周围环境干燥、无强磁场干扰,方便维护操作。
多功能表说明书
SD96-E3说明书1、概述SD96-E3多功能电力仪表用于测量三相电流、三相电压、功率因数、频率;显示采用数码管或液,可以同时显示4种电力参数,不需要切换;适用于高压进线柜、高压电容器柜、低压进线柜、低压电容器柜等;精度高、稳定性好、测量范围广、变比可任意设定,具有通讯功能,支持全数字校表,无可调电位器,具有很高的性价比。
2、技术参数(SD96-E3)性能参数输入测量显示网络三相三线、三相四线电压额定值AC100V、220V、380V(订货时需说明)过负荷测量:1.2倍瞬时:2倍/10s功耗<1V A (每相)阻抗>100kΩ电流额定值AC 1A、5A(订货时需说明)过负荷持续:1.2倍瞬时:10倍/10s功耗< 0.4V A (每相)电流电压三相电流、电压频率45~ 65Hz功率因数-1—0—1显示4排LED同时显示输出数字接口RS-485电源工作范围80~265AC或DC(无极性)45~65Hz 功耗≤5VA环境工作环境-25 ℃~ 55℃储存环境-35 ℃~ 75℃安全耐压输入和电源>AC 2kV 输入和输出>AC 2kV 绝缘输入、输出、电源对机壳>5MΩ外形尺寸120×120,96×96,80×80,72×72 重量0.55kg精度等级0.2级,0.5级3、附件:数字通讯SD96-E3提供串行异步半双工RS485 通讯接口,各种数据讯息均可在通讯线路上传送。
在一条线路上可以同时连接多达247个网络电力仪表,每个网络电力仪表均可设定其通讯地址(Address No.),不同系列仪表的通讯接线端子号码不同,通讯连接应使用带有铜网的屏蔽双绞线,线径不小于0.5mm2。
布线时应使通讯线远离强电电缆或其他强电场环境,推荐采用T 型网络的连接方式1,不建议采用星形或其他的连接方式。
主机查询:查询消息帧包括设备地址、功能代码、数据信息码、校准码。
多功能表使用说明书
多功能表使用说明书
一、功能介绍
多功能表是一款集计时、计数、秒表、闹钟、日期、时间、温湿度、气压等多种功能于一身的智能电子产品。
二、使用方法
1. 计时功能:在计时模式下,按“START/STOP”按钮开始计时,再次按下该按钮暂停计时,长按“RESET”键可清除计时器。
2. 计数功能:进入计数模式后,按下“START/STOP”按钮开始计数,再次按下该按钮停止计数。
计数器最大值是999,达到最大值后将自动清零。
3. 秒表功能:在任意模式下按下“SPLIT/RESET”键可进入秒表模式。
按下“START/STOP”按钮开始和停止记时,按下“SPLIT/RESET”键记录分段时间,长按“SPLIT/RESET”键可清除秒表。
4. 闹钟功能:在时间模式下,按下“ALARM”键进入闹钟设置界面。
按下“+”、“-”按钮调整小时和分钟,长按“ALARM”键可关闭闹钟。
5. 日期、时间功能:进入时间模式后,按下“SET”键进入时间设置界面。
依次
按下“+”、“-”按钮设定年、月、日、时、分。
按下“MODE”键可切换12小时制和24小时制。
6. 温湿度、气压功能:在任意模式下按下“C/F”键可切换温度单位(℃、℉),同时屏幕将显示当前温度、湿度、气压及其趋势。
三、注意事项
1. 请勿将多功能表暴露在高温、潮湿或过于寒冷的环境中,以免造成损坏。
2. 请勿对多功能表进行拆卸或修改,否则可能造成电路故障或人身伤害。
3. 当电池低电量时,请及时更换电池,以免造成影响。
4. 使用过程中如有任何疑问,可查看使用手册或联系售后服务人员。
多功能功率表说明书
4. 再次按下 FUNC(功能)按钮一次后松开,功率表会显示最大线路功率和 出现最大线路功率的时间,功率因数。按下 FUNC(功能)按钮并保 持 5 秒钟,会在该状态下清除最大线路功率显示。
5. 再次按下 FUNC(功能)按钮一次后松开,功率表会显示现行时间和累计 功率因数
10. 显示线路频率 11. 显示功率因数 12. 可调节的最大负载电流和最大负载警告 13. 可调节的价格/千瓦时
总共有 11 个时间段的划分,如下所示: 星期一 星期二 星期三 星期四 星期五 星期六 星期日 星期一 星期二 星期三 星期四 星期五 星期一 星期二 星期三 星期四 星期五 星期六 星期日 星期一 星期二 星期三 星期四 星期五
2. 设置单价 2
PDF created with pdfFactory trial version
在设置完单价 1 后,按下 FUNC(功能)按钮一次后松开,重复上面的步骤
来设置单价 2。
3. 设置过载电流数据
设置完单价 2 后,按下 FUNC(功能)按钮一次后松开
PDF created with pdfFactory trial version
10. LCD 显示——当总电量或总电费溢出时,OVER(过多)就会同时闪亮。 设置现行时间
1. 在时钟显示模式下,按下 SET(设置)按钮一次,“WEEK DAY(周)” 就会同时闪烁,时钟换到 SET(设置)模式。你现在可以设置现行时钟 了。所有进入设置状态时,LCD 会显示”SET”.
d. 按下 SET(设置)按钮一次后松开,第四个最大负载的数字闪烁,
按下 UP(向上)来设置。
安科瑞M1M 30C多功能表用户手册说明书
多功能表M1M 30C用户手册万兴P D FM 1M 30C 用户手册9A K K 108466A 0148FDP兴万M1M30C多功能表用户手册删除水印万兴PDF3目录1.一般信息 (5)1.1.手册的使用和保存 (5)1.2.版权 (5)1.3.免责声明 (5)1.4.一般安全警告 (5)1.5.网络安全免责声明 (6)2.包装内容 (7)3.技术特性 (8)3.1.设备说明 (8)3.2.主要功能 (8)3.3.型号 (8)3.4.外形尺寸 (9)3.5.技术数据 (10)4.安装 (12)4.1.装配 (12)4.2.拆卸 (13)4.3.接线图 (14)5.设备访问 (17)5.1.显示屏 (17)5.2.按钮 (19)5.3.数据输入 (20)6.首次调试 (23)6.1.首次使用所需密码(PWD) (23)6.2.实时时钟(RTC) (24)6.3.布线(WIRI) (24)6.4.电流互感器变比(C T ) (25)6.5.电压互感器变比(VT) (26)7.配置(CONF) (27)7.1.通用 (UNIT) (28)7.2.安装(INST) (31)7.3.历史(HIST) (34)7.4.输入/输出(I/O) (36)7.5.报警(ALM) (38)7.6.通信(COMM) (44)4册手户用表能功多 C 30 M 1M8.数据读取(READ) ...............................................................................................46 8.1.实时(REAL) ........................................................................................................46 8.2.电能(ENRG) .......................................................................................................48 8.3.电能质量(PWQT) .. (49)8.4.最大需量(DEMD ) ...............................................................................................50 8.5.平均值(AVG).. (51)8.6.最大值(MAX)......................................................................................................52 8.7.最小值(MIN). (53)8.8.I/O ...........................................................................................................................54 8.9.通知(NOTF).........................................................................................................55 8.10.历史记录(LOG)................................................................................................59 8.11.计时器(TIME) ...................................................................................................60删除水印万兴PDF9.废弃处理 (61)5 M1M 30C多功能表用户手册1.一般信息1.1.手册的使用和保存在使用本设备之前,请仔细阅读本手册并遵守所述指示。
多功能电力仪表使用说明书
多功能电力仪表使用手册使用手册USER MANUAL目录一、多功能电力仪表使用手册 (2)1、概述 (2)2、技术参数 (2)3、编程和使用 (3)测量显示 (3)编程操作 (5)4、通迅 (10)通迅报文举例 (11)MODBUS地址信息表 (11)5、功能输出 (13)二、多功能三相电压、三相电流、有功电度、无功电度表使用手册 (14)1、概述 (14)2、使用 (14)三、多功能有功电度、无功电度使用手册 (16)4、概述 (16)5、使用 (16)四、多功能三相电流、有功电度表使用手册 (18)1、概述 (18)2、使用 (18)五、接线图 (19)120*120接线图 (20)96*96接线图 (21)80*80接线图 (22)72*72接线图 (23)六、常见问题及解决方法: (24)多功能电力仪表--使用手册一、概述多功能电力仪表是一种具有可编程测量、显示、数字通讯和电能脉冲输出等功能的多功能电力仪表,能够完成电量测量、电能计量、数据显示、采集及传输,可广泛应用变电站自动化,配电自动化、智能建筑、企业内部的电能测量、管理、考核。
测量精度为0.5级、实现LED 现场显示和远程RS-485数字接口通讯,采用MODBUS-RTU通讯协议。
外形代号外形尺寸(mm)测量显示辅助功能42方形120*120*112 相电压、线电压、电流、总有功功率、总无功功率、总功率因素、总视在功率、频率、有功电能、无功电能3排LED分页显示电能脉冲输出数字通讯96方形96*96*1126方形80*80*76数字通讯72方形72*72*105性能参数输入测量显示网络三相三线、三相四线电压额定值AC100V、400V(订货时说明)过负荷持续:1.2倍瞬时:10倍/10s功耗<1VA(每相)阻抗>500kΩ精度RMS测量,精度等级0.5电流额定值AC1A、5A(订货时请说明)过负荷持续:1.2倍瞬时:10倍/10s功耗<0.4VA(每相)阻抗<2mΩ精度RMS测量,精度等级0.5频率40~60Hz,精度0.1Hz功率有功、无功、视在功率,精度0.5级电能四象限计量,有功精度0.5级,无功精度1级显示可编程、切换、循环(LED)显示电源频率AC/DC 85~270V 功率≤5VA输出电能RS-485、MODBUS-RTU协议显示2路电能脉冲输出,光耦继电器(6方形、72方形除外)环境工作范围-10~55℃功耗-20~75℃安全耐压输入/电源>2kV,输入/输出>2kV,电源/输出>1kV 绝缘输入、输出、电源对机壳>5MΩ1)辅助电源:多功能电力仪表具备通用的(AC/DC)电源输入接口,若不作特殊声明,提供的是AC/DC85~270V电源接口的标准产品,保证所提供的电源适用于该系列的产品,以防止损坏产品。
康比利仪表多功能电力仪表说明书
上海康比利仪表有限公司KLY-D96-M-C1、KLY-D96-M-C2KLY-D120-M-C2、KLY-D144-M-C2多功能电力仪表使用说明书$目录危险和警示 (2)基本操作 (2)外 观 (3)安装示意 (3)外形尺寸图 (4)连接示意图 (4)接 线 图 (5)设 置 (6)电压接线检查功能 (10)主要参数及技术指标 (12)功能特性 (13)正常显示操作电流 (14)电压 (14)功率、功率因数 (15)最大值平均值 (16)谐波 (18)电度 (19)端子安装示意图 (20)多功能表型号编写规则 (21)执行标准 (21)可选模块 (22)术语缩写 (23)版本号:V2.2危险及警示该装置必须由专业人员进行安装。
由于不遵守操作说明而导致的故障,制造商将不承担责任。
!不规范使用仪表有触电致死,燃烧以及爆炸的危险注意事项:·该装置必须由具备专业资质的人员进行安装与检修·对该装置进行任何内部或外部操作时,必须切断电压输入和辅助电源,将所有电流互感器的二次侧线圈短路·始终使用合适的电压检测装置来确定无电压·在给装置通电之前,将所有的机械装置、门、封盖都放回正常位置·始终供给装置正确的额定电压·请勿在结露状态下使用·本说明书的内容如有更新,恕不另行通知正常使用前需要检查以下几项:·辅助电源电压·配电系统的频率(50或60Hz)·经过电压输入端子(V1,V2,V3和VN)的最大线电压690VAC和最大相电压400VAC ·经过电流输入端(I1,I2,和I3)的最大电流6A基本操作为了个人和设备的安全,在对设备进行接线前,请务必仔细阅读本说明书。
当您收到货箱时,请检测以下几项:·包装完好无损·运输中产品未被破坏·产品编号与订货相符·包装内包含安装有可拆卸的端子条的产品·使用说明书外观显示的外观:1.6个双功能键(显示或设置,按键的具体功能见第8页。
楚达多功能表说明书
楚达多功能表说明书
多功能表的功能:
1、计量功能:具有正向、反向有功电能量和四象限无功电能量计量功能,同时包括累计计量和实时计量两类功能。
2、费率和时段功能:利用经济杠杆,使用电的峰值和谷值的电价有所差别,至少可设置尖、峰、平、谷四个费率,改善用电质量和经济效益。
3、最大需量计量。
4、测量功能:可测量各分相的有功功率、无功功率、功率因数、分相电压、分相(含零线)电流、频率等运行参数。
5、数据显示功能:多功能表对于电量数据的显示有两种方式:循环显示和固定显示。
显示内容可通过编程进行设置,且具有停电后唤醒显示的功能。
6、通信功能:通信信道物理层必须独立,任意一条通信信道的损坏都不得影响其他信道正常工作,当有重要事件发生时,宜支持主动上报。
此外,智能电能表还具有事件记录功能、停电抄表功能、安全保护功能、时钟功能、冻结功能、清零功能、报警功能辅助电源功能等多种功能。
多功能仪表使用说明书
多功能电力监测仪表使用手册U S E R M A N U A L目 录安全须知 (1)一、产品说明 (2)1.1概述 (2)1.2选型 (2)1.3测量 (3)1.4需量 (4)1.5电能计量 (4)1.6电能脉冲 (5)1.7开关量输入 (6)1.8继电器输出 (6)1.9模拟量输出 (7)1.10通信 (7)1.11电能质量 (7)二、安装与接线 (8)2.1安装尺寸 (8)2.2外形尺寸 (9)2.3安装 (9)2.4接线 (9)三、操作......................................... (11)3.1仪表面板.......................................... .113.2显示 (12)3.3显示界面总览 (14)四、设置 (15)4.1查看系统参数 (15)4.2进入和退出编程状态 (15)4.3设置菜单总览 (15)4.4设置菜单说明 (19)4.5通信设置 (21)4.6输入信号设置 (22)4.7报警项目表........................................ .234.8变送和需量项目表 (24)五、常见问题及解决办法 (24)5.1通信 (24)5.2测量不准确 (25)5.3电能不准确 (25)5.4仪表不亮 (26)5.5其它异常情况 (26)六、技术规格 (26)七、通信说明附录 (27)一、安全须知该装置必须由专业人员进行安装,由于不按照本手册操作而导致的故障,制造商将不承担责任。
请您在使用装置前仔细阅读本手册,并在使用时务必注意以下几点:◆该装置必须由专业人员进行安装与检修◆在对该装置进行任何内部或外部操作前,必须切断电源和输入信号◆始终使用合适的电压检测装置来确定仪表各部位无电压◆提供给该装置的电参数须在额定范围内下述情况会导致装置损坏或装置工作的异常◆辅助电源电压超范围◆配电系统频率超范围◆电流或电压输入极性不正确◆未按要求接线二、产品说明1.概述本系列多功能电力仪表可监测多种电气参数,如电压、电流、频率、功率、功率因数、电能等,并具有开关状态监测、越限报警、模拟量输出、电能脉冲和通信等功能。
MM10数字多功能表 Multimeter操作指南说明书
OPERATING INSTRUCTIONSSERIES MM10 DIGITAL MULTIMETERSAFETY INFORMATIONThe following safety information must be observed to insure maximum personal safety during the operation of this meter.Do not use the meter if the meter or test leads look damaged, or if you suspect that the meter is not operating properly.Never ground yourself when taking electrical measurements. Do not touch exposed metal pipes, outlets, fixtures, etc., which might be a ground potential. Keep your body isolated from ground by using dry clothing, rubber shoes, rubber mats, or any approved insulating material.Turn off power to the circuit under test before cutting, unsoldering, or breaking the circuit. Small amounts of current can be dangerous.Use caution when working above DC 60V or AC 30Vrms. Such voltages pose a shock hazard.When using the probes, keep your fingers behind the finger guards on the probes.Measuring voltage which exceeds the limits of the multimeter may damage the meter and expose the operator to a shock hazard. Always recognize the meter voltage limits as stated on the front of the meter.GENERAL SPECIFICATIONSDisplay: 3-1/2 digit liquid crystal display (LCD) with a maximum reading of 1999.Polarity: Automatic, positive implied, and (-) for negative polarity indication.Overload: (1) or (-1) is displayed on LCD.Low Battery Indication: When " " shows on LCD, battery needs to be replaced.Sampling Rate: 2.5 times per second.Operating Environment: 0°C~40°C 80% RH.Storage Temperature: -10°C~60°C 0~80% RH with battery removed from meter.Power: One 006P 9V standard battery. Battery Life: 150 hours approx.Dimension: 125 mm (H) x 68 mm (W) x 25 mm (D). Weight: 150g approx. including battery.Accessory: Instruction manual, test leads, (1) 9V battery.SPECIFICATIONSDCVRange Resolution Accuracy Input Impedance Overload Protection 2V 1mV 0.5% + 1 dgt 20V 10mV200V 100mV600V 1V 1.5% + 1 dgt 10M ΩDC 600V AC 600V rmsACVRange ResolutionAccuracyInput Impedance Overload Protection 200V 100mV 2% + 3 dgt(40 Hz-500 Hz)600V 1V 2.5% + 3 dgt 4.5M ΩDC 600V AC 600V rmsResistance (Ω) Range Resolution Accuracy Open Voltage Overload Protection200Ω 0.1Ω 2% + 2 dgt 2K Ω 1Ω 2.8V20K Ω 10Ω 200K Ω 100Ω 2M Ω 1K Ω1.5% + 2 dgt20M Ω 10K Ω 2.5% + 2 dgt0.3VDC/AC 500V rmsDiode TestRange ResolutionTest CurrentOpen VoltageOverloadProtection1mV 1mA ≈2.8V DC/AC 500V rmsOPERATIONDCV (ACV) Measurement1. Plug red test lead to "VΩmA" jack, and black test lead to"COM" jack.2. Turn the function/range selector to "DCV" or "ACV" region.(If measuring an unknown voltage, start from the highestrange then adjust to a proper lower range for the bestresolution.)3. Connect the other ends of the test leads to the desiredcircuit.4. Get the reading from the LCD.DCA Measurement1. Plug red test lead to "VΩmA" jack (if measuring a currentbetween 200mA and 10A, plug to "10A" jack instead), andblack test lead to "COM" jack.2. Turn the function/range selector to "DCA" region. (Ifmeasuring an unknown current, start from the highest range then adjust to a proper lower range for the best resolution.)3. Connect the other ends of the test leads in series with thedesired circuit.4. Get the reading from the LCD.Resistance Measurement1. Plug red test lead to "VΩmA" jack, and black test lead to"COM" jack.2. Turn the function/range selector to "Ω" region (if measuringan unknown resistance, start from the highest range, thenadjust to a proper lower range for the best resolution).3. Connect the other ends of the test leads to the desiredresistor.4. Get the reading from the LCD.Diode () Measurement1. Plug red test lead to "VΩmA" jack, and black test lead to"COM" jack.2. Turn the function/range selector to "" range.3. Connect the other end of red test lead to the positive pole(P) of the diode, and the other end of the black test lead tothe negative pole (N).4. Get the reading from the LCD. (If connection to poles ofdiode is reverse, LCD would display "I".)Continuity x Measurement1. Plug red test lead to "VΩmA" jack, and black test lead to"COM" jack.2. Turn the function/range selector to " x" range.3. Connect the other ends of the test leads to the desiredresistor.4. Get the reading from the LCD.hFE Measurement (for Transistor)1. Turn the function/range selector to "hFE" (NPN or PNP)region.2. Insert the transistor pins into "hFE" jack according to E.B.C.sequence.3. Get the reading from the LCD.LED Test1. Turn the function/range selector to "NPN/LED" range.2. Insert the LED into the measuring jack according to the "+" "-" position, and a normal LED will be bright.3. This function is used only to judge a LED rated 15V~3V forits brightness or not. The reading on LCD means nothing. MAINTENANCEWARNING: Remove test leads before changing battery or fuse or performing any servicing.Battery ReplacementPower is supplied by a 9 volt "transistor" battery (006P DC9V). The " " shown on the LCD indicates that replacement is needed. When replacing, remove the two screws from the back of the meter and lift off the rear case. Remove the battery from the case on bottom.Fuse ReplacementIf no current measurements are possible, check for a blown overload protection fuse. Replace the fuse with the original type 0.5A/250V, fast acting type.。
多功能表操作说明
多功能表操作说明Acuvim390、330、327操作说明:1.查看电流、电压参数:V/A键,实现查看和翻屏功能2.查看功率参数:,实现查看系统有功功率P(KW)、无功功率Q(KVar)、视在功率S (KVA)3.查看电度:,实现查看系统有功电能Ep(KWh)、无功电能Eq(Kvarh)、视在电能Es(KVAh),其中常规看的电度为:系统有功电能Acuvim188操作说明:1.查看电流、电压、功率参数:V/A键,实现查看和翻屏功能2.查看电度:F键,实现查看系统有功电能Ep(KWh),其中常规看的电度为:系统有功电能仪表常见问题排查(确保接线正确情况下):1.电流测量不准情况:检测CT设置参数是否跟实际CT额定参数一致2.电压测量不准情况:检测pT设置参数是否跟实际pT额定参数一致3.电度测量不准情况:首先检测电流、电压测量参数是否正确,否则调整相应参数设置然后检查实际接线与系统设置接线方式是否正确,否则调整相应参数设置系统参数设置:Acuvim390、330、327设置:同时按F和V/A键,进入密码登陆界面,出厂默认密码为0000,如下图:按V/A键翻至仪表接线方式设定页。
“仪表接线方式”可设定为“3Ln”、“3LL”、“2LL”和“1Ln”。
相关内容请参考用户使用手册。
如下图:接线方式设定为3Ln。
使用“↑”键或者“↓”键进行接线方式切换。
按“V/A”键确认并进入下一屏设定页。
按V/A键进入系统参数设置,然后使用V/A键翻屏,翻到第四屏(PT设置界面),设置PT一次侧额定电压值,如下图按V/A键翻到如下界面,设置PT二次侧额定电压值(电压直接接入情况下,设定值与一次侧相同)按V/A键翻到如下界面,设置CT一次侧额定电流值,设定值应与现场CT一侧额定值一致按V/A键翻到如下界面,设置CT二次侧额定电流值,仪表出厂前根据客户要求设定5A或1A的固定值,其值不可更改AO模拟量的参数设置:在系统参数设置模式下,同时按F和按键,进入如下界面:模拟量AO1跟随量的设定界面:(根据仪表型号不同,其具体功能也不同,选定恰当的变送跟随量,如下表)按V/A键进入下图设置界面,为满足不同用户的需求,Acuivm 300 扩展AO提供变送范围选择。
三相多功能电力仪表 使用手册说明书
三相多功能电力仪表使用手册(适用于72 、80、96、120尺寸的单相电流表、单相电压表、三相电流表、三相电压表、多功能表)(液晶显示型)VER2.2 2022.11.25更新一、功能介绍● 测量功能电压测量:可直接测量或通过PT 测量三相相电压或线电压值,显示量程为999999V (测量范围10-450v )。
电流测量:可直接测量或通过CT 测量三相电流值,显示量程为9999A (测量范围0.005A-6A )。
有功功率:可测量三相总有功功率和分相(不含三相三)的有功功率,有符号位。
无功功率:可测量三相总无功功率和分相(不含三相三)的无功功率,有符号位。
功率因数:可测量三相总的功率因数和分相的功率因数,(范围为-1到+1)。
频率:可测量电网系统频率,单位为Hz 。
● 计量功能有功电量:可计量总有功电量和分相的有功电量。
电量采用累计的方式计算,除非用户清零,否则一 直累计到最大值后重新开始,电能计量的最大值为9999999kWh 。
总有功电量是分相有功电量的绝对值之和。
当电流大于0.005A 开始计量,电流大于0.25A (额定电流5A 的5%),满足计量精度标准 无功电度:可计量总的无功电量和分相的无功电量。
无功电量的单位为kvah 。
● 脉冲输出功能(选配)可选配脉冲输出:提供有功校验脉冲,为光耦开漏输出,使用时需要加5-24v 上拉,常数为3200imp/kWh 。
● 通讯功能(选配)485通讯,采用标准MODBUS-RTU 通讯协议。
波特率和数据格式可根据实际需要灵活配置。
在组网时,如果出现通讯不顺畅的现象,可在网路末端并联一个120欧姆左右的电阻进行信号匹配。
● 显示功能:采用高清白色段式液晶屏(LCD )显示,清晰直观。
● 开关量输入输出功能:(选配)仪表可选配最多8路开关量输入或4路开关量输出。
(使用方法见附加说明)二、安装尺寸和接线外形代号 外框尺寸mm A×B壳体尺寸mmC*C开孔尺寸mm E×F长度mm L72 72×72 66×66 67×67 38(短款)或58 80 83×83 75×75 76×76 38(短款)或5896 96×96 90×90 91×91 52 120 120×120110×110111×11171© Copyright reserved 安装、使用产品前请先阅读本操作手册,并保留备用1. 安装方式面板式安装,柜体的开孔尺寸可按照上表所示。
模型77系列IV数字多功能表器用户手册说明书
®Model 77 Series IVDigital MultimeterUsers ManualPN 2695884September 2006© 2006 Fluke Corporation. All rights reserved. Printed in USAAll product names are trademarks of their respective companies.Lifetime Limited WarrantyEach Fluke 20, 70, 80, 170 and 180 Series DMM will be free from defects in material and workmanship for its lifetime. As used herein, “life-time” is defined as seven years after Fluke discontinues manufacturing the product, but the warranty period shall be at least ten years fromthe date of purchase. This warranty does not cover fuses, disposable batteries, damage from neglect, misuse, contamination, alteration, accident or abnormal conditions of operation or handling, including failures caused by use outside of the product’s specifications, or normalwear and tear of mechanical components. This warranty covers the original purchaser only and is not transferable.For ten years from the date of purchase, this warranty also covers the LCD. Thereafter, for the lifetime of the DMM, Fluke will replace the LCD for a fee based on then current component acquisition costs.To establish original ownership and prove date of purchase, please complete and return the registration card accompanying the product, orregister your product on . Fluke will, at its option, repair at no charge, replace or refund the purchase price of a defective product purchased through a Fluke authorized sales outlet and at the applicable international price. Fluke reserves the right to charge for importation costs of repair/replacement parts if the product purchased in one country is sent for repair elsewhere.If the product is defective, contact your nearest Fluke authorized service center to obtain return authorization information, then send the product to that service center, with a description of the difficulty, postage and insurance prepaid (FOB Destination). Fluke assumes no risk for damage in transit. Fluke will pay return transportation for product repaired or replaced in-warranty. Before making any non-warranty re-pair, Fluke will estimate cost and obtain authorization, then invoice you for repair and return transportation.THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE, AREEXPRESSED OR IMPLIED. FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAM-AGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY. AUTHORIZED RESELLERS ARE NOT AUTHORIZED TO EXTEND ANY DIFFERENT WARRANTY ON FLUKE’S BEHALF. Since some states do not allow the exclusion or limita-tion of an implied warranty or of incidental or consequential damages, this limitation of liability may not apply to you. If any provision of this warranty is held invalid or unenforceable by a court or other decision-maker of competent jurisdiction, such holding will not affect the validity or enforceability of any other provision.Fluke Corporation Fluke Europe B.V.P.O. Box 9090 P.O. Box 1186Everett, WA 98206-9090 5602 BD EindhovenNetherlandsU.S.A. TheVisit the Fluke website at: Register your Meter at: 2/02Table of ContentsPage TitleContacting Fluke (1)Warning and Caution Statements (1)Unsafe Voltage (1)Test Lead Alert (1)Battery Saver (Sleep Mode) (2)Terminals (2)Rotary Switch Positions (2)Display (3)MIN MAX AVG Recording Mode (4)AutoHOLD Modes (4)YELLOW Button (4)Display Backlight (4)Manual Ranging and Autoranging (5)Power-Up Options (5)Making Basic Measurements (6)Measuring AC and DC Voltage (6)Measuring Resistance (6)Measuring Capacitance (6)Testing for Continuity (7)Testing Diodes (7)Measuring AC or DC Current (8)Measuring Frequency (8)Using the Bar Graph (9)Cleaning (9)Testing the Fuses (9)Replacing the Battery and Fuses (10)Specifications (11)iXW Warning. Read before using the MeterTo avoid possible electrical shock or personal injury, follow these guidelines:⇒Use the Meter only as specified in this manual or the protection provided by the Meter might be impaired.⇒Do not use the Meter or test leads if they appear damaged, or if the Meter is not operating properly. If in doubt, have the Meter serviced.⇒Always use the proper terminals, switch position, and range for measurements.⇒Verify the Meter's operation by measuring a known voltage.⇒Do not apply more than the rated voltage, as marked on the Meter, between the terminals or between any terminal and earth ground.⇒Use caution with voltages above 30 V ac rms, 42 V ac peak, or 60 V dc. These voltages pose a shock hazard.⇒Disconnect circuit power and discharge all high-voltage capacitors before testing resistance, continuity, diodes, or capacitance.⇒Do not use the Meter around explosive gas or vapor.⇒When using the test leads, keep your fingers behind the finger guards.⇒Remove test leads from the Meter before opening the Meter case or battery door.SymbolsB AC (Alternating Current) I FuseF DC (Direct Current) P Conforms to European Union directivesFB DC/AC $Canadian Standards AssociationJ Earth ground T Double insulatedW Important Information; see manual X Hazardous Voltageb Battery (Low battery when shown ondisplay) ! Underwriters Laboratories, Inc.Meter in accordance with IEC 61010-1. 54CJs Inspected and licensed by TÜV(Technischer Überwachungs Verein)Product Services;N10140Conforms to relevant Australian standards#VDE (Verband Deutscher Electroniker)iiModel 77 Series IVDigital MultimeterThe Fluke Model 77 Series IV is a battery-powered, average responding-rms indicating multimeter (hereafter "the Meter"), with a 6000-count, 3 3/4-digit display, and a bar graph.This meter meets CAT III and CAT IV IEC 61010 standards. The IEC 61010 safety standard defines four measurement categories (CAT I to IV) based on the magnitude of danger from transient impulses. CAT III meters are designed to protect against transients in fixed-equipment installations at the distribution level; CAT IV meters are designed to protect against transients from the primary supply level (overhead or underground utility service).The Meter measures or tests the following:♦AC / DC voltage & current ♦Diodes♦Resistance ♦Continuity♦Voltage frequency ♦Capacitance Contacting FlukeTo contact Fluke, call:1-888-993-5853 in USA1-800-363-5853 in Canada+31 402-675-200 in Europe+81-3-3434-0181 in Japan+65-738-5655 in Singapore+1-425-446-5500 from anywhere in the worldVisit Fluke's web site at: Register your Meter at: Warning and Caution StatementsA X W Warning identifies hazardous conditions and actions that could cause bodily harm or death.A Caution identifies conditions and actions that could damage the Meter, the equipment under test, or cause permanent loss of data. Unsafe VoltageTo alert you to the presence of a potentially hazardous voltage, when the Meter detects a voltage ≥30 V or a voltage overload (OL), the Y symbol is displayed.Test Lead AlertTo remind you to check that the test leads are in the correct terminals, LEAd is momentarily displayed when you move the rotary switch to or from the mA or A position.W WarningAttempting to make a measurement with a test lead inan incorrect terminal might blow a fuse, damage theMeter, and cause serious personal injury.1Model 77 Series IV Users Manual2Battery Saver (Sleep Mode)The Meter enters the "Sleep" mode and blanks out the display if there is no function change or button press for 20 minutes. To disable the Sleep mode, hold down the yellow button while turning the Meter on. The Sleep mode is always disabled in the MIN MAX AVG mode and the AutoHOLD mode.TerminalsRotary Switch PositionsSwitch PositionMeasurement FunctionK Hz AC voltage from 0.001 to 1000 V. Frequency from 2 Hz to 99.99 kHz. L DC voltage from 1 mV to 1000 V. m L DC mV from 0.1 mV to 600 mV. e E Ohms from 0.1 Ω to 50 M Ω. Farads from 1 nF to 9999 μF.R G Beeper turns on at <25 Ω and turns off at >250 Ω. Diode test. Displays OL above 2.4 V. F B mA AC mA from 0.01 mA to 400 mA. DC mA from 0.01 mA to 400 mA. F B AAC A from 0.001 A to 10 A. DC A from 0.001 A to 10 A >10.00 display flashes. >20 A, OL is displayed.Display3DisplayNo. SymbolMeaning8 DC, ACDirect current, alternating current. 9 bLow battery. Replace battery. 10 610000mV All possible ranges. 11 Bar graph Analog display.12Auto RangeManual RangeThe Meter selects the range with the best resolution.The user selects the range. 13±Bar graph polarity. 14 0L The input out of range.15 LEAdW Test lead alert. Displayed when the rotary switch is moved to or from the mA or A position. Error MessagesbAtt Replace the battery immediately.diSC In the capacitance function, too much electrical charge is present on the capacitor being tested. EEPr Err Invalid EEPROM data. Have Meter serviced. CAL ErrInvalid calibration data. Calibrate Meter.Model 77 Series IV Users Manual4MIN MAX AVG Recording ModeThe MIN MAX AVG recording mode captures the minimum and maximum input values, and calculates a running average of all readings. When a new high or low is detected, the Meter beeps.NoteFor dc functions, accuracy is the specified accuracy of the measurement function ±12 counts for changes longer than 275 ms in duration.For ac functions, accuracy is the specified accuracy of the measurement function ±40 counts for changes longer than 1.2 s in duration.To use MIN MAX AVG recording:⇒ Make sure that the Meter is in the desired measurementfunction and range. (Autoranging is disabled in the MIN MAX AVG mode.)⇒ Press MIN MAX to activate MIN MAX AVG mode.m and MAX light, and the highest reading detected since entering MIN MAX AVG is displayed.⇒ Press MIN MAX to step through the low (MIN ), average(AVG ), and present readings.⇒ To pause MIN MAX AVG recording without erasing storedvalues, press HOLD . h is displayed.To resume MIN MAX AVG recording, press HOLD again. h turns off.⇒ To exit and erase stored readings, press MIN MAX for 1second or turn the rotary switch.AutoHOLD ModesXW WarningTo avoid electric shock, do not use the AutoHOLD mode to determine if a circuit is live. Unstable or noisy readings will not be captured.In the AutoHOLD mode, the Meter holds the reading on the display until it detects a new stable reading. Then the Meter beeps, and displays the new reading.⇒ Press HOLD to activate AutoHOLD. h lights.⇒ Press HOLD again or turn the rotary switch to resume normaloperation.YELLOW ButtonPress the yellow button to select alternate measurement functions on a rotary switch setting, e.g., to select DC mA, DC A, Hz, capacitance, or diode test.Display BacklightPress S to toggle the backlight on and off. The backlightautomatically turns off after 2 minutes.Manual Ranging and Autoranging5Manual Ranging and AutorangingThe Meter has both Manual range and Autorange modes.⇒ In the Autorange mode, the Meter selects the range with thebest resolution.⇒ In the Manual Range mode, you override Autorange and selectthe range yourself.When you turn the Meter on, it defaults to Autorange and Auto Range is displayed.1. To enter the Manual Range mode, press RANGE .Manual Range is displayed.2. In the Manual Range mode, press RANGE to increment therange. After the highest range, the Meter wraps to the lowest range.NoteYou cannot manually change the range in the MIN MAX AVG mode.If you press RANGE while in MIN MAX AVG, the Meter beeps, indicating an invalid operation, and the range does not change.3. To exit Manual Range, press RANGE for 1 second or turn therotary switch.The Meter returns to Autorange and Auto Range is displayed.Power-Up OptionsTo select a Power-Up Option, hold down the button indicated while turning the Meter on.Power-Up Options are cancelled when the Meter is turned OFF.ButtonPower-Up OptionsH Turns on all display segments when in VAC switch position.M Disables beeper. bEEP is diplayed when enabled. REnables "Smoothing" mode. '___ is displayed when enabled.Dampens display fluctuations of rapidly changing inputs by digital filtering.B(YELLOW)Disables automatic power-down ("Sleep mode"). PoFF is displayed when enabledSleep mode is also disabled while the Meter is in a MIN MAX AVG Recording mode, or the AutoHOLD mode.SDisables automatic 2-minute backlight timeout. LoFF is displayed when enabled.Model 77 Series IV Users Manual6Making Basic MeasurementsThe figures on the following pages show how to make basic measurements.When connecting the test leads to the circuit or device, connect the common (COM ) test lead before connecting the live lead; when removing the test leads, remove the live lead before removing the common test lead.XW WarningTo avoid electric shock or injury, or damage to the Meter, disconnect circuit power and discharge all high-voltage capacitors before testing resistance, continuity, diodes, or capacitance. Measuring AC and DC VoltageVolts ACVolts DCAIK03F.EPSMeasuring ResistanceAIK04F.EPSMeasuring CapacitanceAIK05F.EPSMaking Basic MeasurementsTesting for ContinuityAIK06F.EPS Testing DiodesOpenAIK07F.EPSUsers ManualMeasuring AC or DC CurrentXW WarningTo avoid personal injury or damage to the Meter: •Never attempt to make an in-circuit current measure-ment when the open-circuit potential to earth ground is >1000 V.•Check the Meter's fuses before testing. (See “Testing the Fuses”.)•Use the proper terminals, switch position, and range for your measurement.•Never place the probes in parallel with a circuit or component when the leads are plugged into thecurrent terminals.Turn power OFF, break circuit, insert Meter in series, turn power on.Measuring FrequencyX W WarningTo avoid electrical shock, disregard the bar graph forfrequencies >1 kHz. If the frequency of the measuredsignal is >1 kHz, the bar graph is unspecified.The Meter measures the frequency of a signal. The trigger level is 0 V ac for all ranges.AC Voltage FrequencyEOM09F.EPS ⇒To exit frequency, press yellow button or turn the rotary switch.⇒In frequency, the bar graph shows the ac voltage accurately up to 1 kHz.⇒Select progressively lower ranges using manual ranging for a stable reading.Using the Bar GraphUsing the Bar GraphThe bar graph is like the needle on an analog Meter. There is an overload indicator (►) to the right, and a polarity indicator (±) to the left.Because the bar graph is much faster than the digital display, the bar graph is useful for making peak and null adjustments, and for observing rapidly changing inputs.The bar graph is disabled when measuring capacitance. In frequency, the bar graph accurately indicates the voltage or current up to 1 kHz.The number of lit segments indicates the measured value and is relative to the full-scale value of the selected range.For example, in the 60 V range (see below), the major divisions on the scale represent 0, 15, 30, 45, and 60 V. An input of −30 V lights the negative sign and the segments up to the middle of thescale.AIK11F.EPS CleaningWipe the case with a damp cloth and mild detergent. Do not use abrasives or solvents. Dirt or moisture in the terminals can affect readings.Testing the FusesXW WarningTo avoid electrical shock or injury, remove the testleads and any input signals before replacing the fuse. Test fuses as shown below.AIK12F.EPSUsers ManualReplacing the Battery and FusesXW WarningTo avoid shock, injury, or damage to the Meter:•Use ONLY fuses with the amperage, interrupt, voltage, and speed ratings specified. Disconnect test leads before opening case.SpecificationsSpecificationsAccuracy is specified for 1 year after calibration, at operating temperatures of 18 °C to 28 °C, with relative humidity at 0 % to 90 %. Accuracy specifications take the form of the following calculations:± ( [ % of Reading ] + [ Counts ] )Maximum voltage between anyterminal and earth ground: 1000Surge Protection: 8 kV peak per IEC 61010W Fuse for mA inputs: W Fuse for A input: 440 mA, 1000 V FAST Fuse 11 A, 1000 V FAST FuseDisplay: Digital: 6000 counts, updates 4/secBar Graph: 33 segments; updates 32/secFrequency: 10,000 countsCapacitance: 1,000 countsAltitude: Operating: 2000 m; Storage: 12,000 mTemperature: Operating: −10 °C to +50 °C;Storage: −40 °C to +60 °CTemperature coefficient: 0.1 X (specified accuracy) / °C(<18 °C or >28 °C)Electromagnetic Compatibility(EN 61326-1:1997): In an RF field of 3 V/M, accuracy = specified accuracy.Relative Humidity:Maximum, noncondensing90 % to 35 °C75 % to 40 °C;45 % to 50 °CBattery Life: Alkaline: 400 hrs typicalSize (H x W x L): 4.3 cm x 9 cm x 18.5 cmWeight: 420 gSafety Compliances: ANSI/ISA S82.02.01, CSA C22.2-1010.1, IEC 61010 to 1000 V Measurement Category III, 600 V Measurement Category IVCertifications: CSA, TÜV (EN61010), UL, P, ; (N10140),VDEUsers ManualFunction Range Resolution Accuracy ± ( [ % of Reading ] + [ Counts ] )AC Volts (Average responding) 6.000 V60.00 V600.0 V1000 V0.001 V0.01 V0.1 V1 V2.0 % + 2(45 Hz to 1 kHz)DC mV 600.0 mV 0.1 mV 0.3 % + 1DC Volts 6.000 V60.00 V600.0 V1000 V 0.001 V0.01 V0.1 V1 V0.3 % + 1Continuity 600Ω 1ΩMeter beeps at <25 Ω, beeper turns off at >250 Ω;detects opens or shorts of 250 μs or longer.Ohms 600.0 Ω6.000 kΩ60.00 kΩ600.0 kΩ6.000 MΩ50.00 MΩ0.1 Ω0.001 kΩ0.01 kΩ0.1 kΩ0.001 MΩ0.01 MΩ0.5 % + 20.5 % + 10.5 % + 10.5 % + 10.5 % + 12.0 % + 1Diode test 2.400 V 0.001 V 1 % + 2Capacitance 1000 nF10.00 μF100.0 μF9999 μF[1]1 nF0.01 μF0.1 μF1 μF1.2 % + 21.2 % + 21.2 % + 210 % typicalAC Amps (Average responding)[2] 60.00 mA400.0 mA[3]6.000 A10.00 A[4]0.01 mA0.1 mA0.001 A0.01 A2.5 % + 2(45 Hz to 1 kHz)[1] In the 9999 μF range for measurements to 1000 μF, the measurement accuracy is 1.2 % + 2.[2] Amps input burden voltage (typical): 400 mA input 2 mV/mA, 10 A input 37 mV/A.[3] 400.0 mA accuracy specified up to 600 mA overload.[4] >10 A unspecified.Specifications Function Range Resolution Accuracy ± ( [ % of Reading ] + [ Counts ] )DC Amps[3]60.00 mA400.0 mA[4]6.000 A10.00 A[5]0.01 mA0.1 mA0.001 A0.01 A1.5 % + 2Hz [1][ 2](ac voltage input ) 99.99 Hz999.9 Hz9.999 kHz99.99 kHz0.01 Hz0.1 Hz0.001 kHz0.01 kHz0.1 % + 1MIN MAX AVG For dc functions, accuracy is the specified accuracy of the measurement function ±12 counts for changes longer than 275 ms in duration.For ac functions, accuracy is the specified accuracy of the measurement function ±40 counts for changes longer than1.2 s in duration.[1] Frequency is specified from 2 Hz to 99.99 kHz.[2] Below 2 Hz, the display shows zero Hz.[3] Amps input burden voltage (typical): 400 mA input 2 mV/mA, 10 A input 37 mV/A.[4] 400.0 mA accuracy specified up to 600 mA overload.[5] >10 A unspecified.Users ManualFunction Overload Protection[1]Input Impedance(Nominal)Common Mode Rejection Ratio(1 k Ω Unbalanced) Normal Mode RejectionVolts AC 1000 V >10 M Ω <100 pF >60 dB @ dc, 50 Hz or 60 HzVolts DC1000 V>10 M Ω <100 pF >120 dB @ dc, 50 Hz or 60 Hz >60 dB @ 50 Hz or 60 Hz mV 1000 V [2]>10 M Ω <100 pF>120 dB @ dc, 50 Hz or 60 Hz >60 dB @ 50 Hz or 60 HzOpen Circuit TestVoltageFull Scale Voltage To:6.0 M Ω 50 M ΩShort Circuit Current Ohms/Capacitance 1000 V [2] <8.0 V dc <660 mV dc<4.6 V dc<1.1 mA Continuity/Diode test1000 V [2]<8.0 V dc2.4 V dc<1.1 mA[1] 10 7V-Hz maximum.[2] For circuits <0.3 A short circuit. 660 V for high energy circuits.Function Overload Protection OverloadmA Fused, 440 mA, 1000 V FAST Fuse 600 mA overload for 2 minutes maximum, 10minutes rest.AFused, 11 A, 1000 V FAST Fuse20 A overload for 30 seconds maximum, 10 minutes rest.。
SPM-3 Multi-Function Power Meter 多功能数位电力表说明书
SPM-3Multi-Function Power Meter多功能數位電力表User guide使用手冊士林電機廠股份有限公司Shihlin Electric Corporation新竹縣湖口鄉鳳凰村中華路二十三號.電話:886-3-598-1921 傳真:886-3-598-1480網址:目錄第一章產品介紹1.1 SPM-3簡介1.2 安全須知1.2.1 危險注意1.2.2 產品保固及售後服務1.3 產品規格第二章安裝及接線2.1 產品檢查2.2 產品安裝2.2.1 產品外型第三章線路接線圖3.1 背面接線3.1.1 輔助電源3.1.2 數位輸出Digital Output 3.1.3 電流輸入端子3.1.4 電壓輸入端子3.2 接線圖3.2.1 單相二線式/1CT3.2.2 單相三線式/2CT3.2.3 三相三線式/2CT3.2.4 三相三線式/3CT3.2.5 三相四線式/3CT第四章面板顯示及設定4.1面板顯示4.2 執行期模式4.2.1按鍵M4.2.2按鍵P4.2.3按鍵E/T4.2.4按鍵V/A4.3 設定期模式4.3.1 一般設定N4.3.2 清除設定C4.3.3 警報設定A4.4 特殊功能按鍵第五章通訊5.1 RS4855.1.1 RS485標準5.1.2儀器通訊接線5.2 Modbus5.2.1 Modbus的格式5.3 通訊協定5.4浮點格式5.5 Modbus RTU Mode5.6 Modbus Function Code 5.7 通訊參數明細第一章產品介紹1.1 SPM-3簡介SPM-3為一高精度多功能電表,可應用於一般單、三相系統之電力監視量測、分析、儲存,具有完整的電力量測功能,包括電流、電壓、電量、瓦特、功因、瓦時、頻率、需量,有效及無效電能計算等。
其產品特色如下:●符合IEC62053-22 Class 0.5規範●精度高,V.I.精度優於0.2%,Wh精度優於0.5%,可做雙向電能量測。
casiomultiband6说明
casiomultiband6说明
(原创版)
目录
1.产品简介
2.产品特点
3.应用范围
4.使用说明
5.总结
正文
1.产品简介
Casio Multiband 6 是一款由卡西欧公司推出的多功能手表,具备六局电波接收、太阳能充电、全自动日历等功能。
这款手表以其精准的计时、节能环保的设计以及时尚的外观在市场上备受欢迎。
2.产品特点
Casio Multiband 6 具有以下显著特点:
(1) 六局电波接收:该手表能够接收来自六个不同频率的电波信号,确保时间精确无误。
(2) 太阳能充电:手表采用太阳能充电技术,环保节能,无需更换电池。
(3) 全自动日历:具备全自动日历功能,可自动调整为闰年和平年,方便用户使用。
(4) 背光功能:在弱光环境下,手表具备背光功能,方便用户清晰读取时间。
(5) 防水设计:Casio Multiband 6 具有防水功能,可在日常生活中
进行游泳、洗澡等活动。
3.应用范围
Casio Multiband 6 适用于各种场合,包括商务、休闲、运动等,适合不同年龄层和性别的用户。
4.使用说明
(1) 在使用前,请确保手表在充足阳光下充电,以确保手表有足够的电量运行。
(2) 手表在充电过程中,请勿操作手表按钮,以免影响充电效果。
(3) 在佩戴手表时,请注意保持手表干燥,避免手表进水。
(4) 如需调整时间,请按照手表说明书中的指引进行操作。
5.总结
Casio Multiband 6 凭借其精准的计时、节能环保的设计以及时尚的外观,成为消费者心中的理想选择。
数字多功能表计说明书
TM/exclusive-brands /exclusive-brands72-260572-1040572-261072-1041072-10415TM/exclusive-brands /exclusive-brands General CharacteristicsSafety Rating : CAT III 1000V, CAT IV 600V Power : 9V Battery (6F22)LCD Size : 65mm × 43mm Colour : Orange and Grey Weight: 370gDimension (H × W × L): 180mm × 87mm × 47mmElectrical SpecificationsParameters 72-260572-1040572-261072-1041072-10415DC Voltage(V)400mV/4V/40V/400V/1000V±(0.5% +1 digit)40mV/400mV/4V/40V/400V/1000V±(0.5% +1 digit)60mV/600mV/6V/60V/600V/1000V±(0.5% +1 digit)220mV/2.2V/22V/220V/1000V±(0.1% +2 digits)AC Voltage(V)400mV/4V/40V/400V/ 750V±(1% +3 digits)40mV/400mV/4V/40V/400V/750V± (1% +3 digits)60mV/600mV/6V/60V/600V/750V±(1% +3 digits)220mV/2.2V/22V/220V/750V±(0.8% +10 digits)DC Current(A)400μA/4000μA/40mA/400mA/4A/10A± (1% +2 digits)600μA/6000μA/60mA/600mA/6A/10A±(1% +3 digits)200μA/2200μA/22mA/220mA/ 2.2A/10A ±(0.5% +10 digits)AC Current(A)400μA/4000μA/40mA/400mA/4A/10A±(1.2% +5 digits)600μA/6000μA/60mA/600mA/6A/10A±(1.2% +5 digits)200μA/2200μA/22mA/220mA/10A ±(0.8% +10 digits)Resistance(Ω)400Ω/4kΩ/40kΩ/400kΩ/4MΩ/40MΩ±(1% +2 digits)600Ω/6kΩ/60kΩ/600kΩ/6MΩ/60MΩ±(1% +2 digits)220Ω/2.2kΩ/22kΩ/220kΩ/2.2MΩ/22MΩ /220MΩ ±(0.5% +10 digits)Capacitance(F)40nF/400nF/4μF/40μF/400μF/4000μF±(3% +5 digits)40nF/400nF/4μF/40μF/400μF/4000μF±(3% +5 digits)22nF/220nF/2.2μF/22μF/220μF/2.2mF/22mF/220mF ±(3% +5 digits)Frequency (Hz)10Hz to 10MHz ±(0.1% +4 digits)10Hz to 10MHz ±(0.1% +4 digits)10Hz to 10MHz ±(0.1% +4 digits)10Hz to 10MHz ±(0.1% +4 digits)10Hz to 220MHz ±(0.01% +5 digits)Temperature(°C)--40°C to 1000°C ±(1.2% +3 digits)-40°C to 1000°C ±(1.2% +3 digits)--Temperature(°F)--40°F to 1832°F ±(1.2% +4 digits)-40°F to 1832°F ±(1.2% +4 digits)--Display Count 400040006000600022000True RMS ---Yes Yes Bandwidth (Hz)45Hz - 400Hz45Hz - 400Hz45Hz - 1kHz45Hz - 3kHz45Hz - 10kHzTransistor Yes ----NCV Yes ----Peak Value ----Yes RS232-Yes Yes Yes Yes Analog Bar Graph 41 Segments 41 Segments61 Segments61 Segments46 SegmentsStandard AccessoriesBattery, Test Lead, Multi-Purpose Socket, Instruction ManualBattery, Test Lead, Multi-Purpose Socket,RS-232 Interface Cable, Software,Point Contact Temperature Probe, Instruction ManualBattery, Test Lead, Multi-Purpose Socket,RS-232 Interface Cable, Software, Instruction ManualFeatures• LCD backlight • Analog Bar Graph• Manual Function Select & Auto Ranging • Auto Power Off• Low Battery Indication: ≤ 7.5V •Diode Test• Continuity Buzzer• MAX / MIN / Relative Modes • Data Hold• Duty Cycle: 0.1% ~ 99.9%• Input Protection•Input Impedance for DC Voltage: 10MΩTM/exclusive-brands /exclusive-brands Important Notice : This data sheet and its contents (the “Information”) belong to the members of the Premier Farnell group of companies (the “Group”) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its negligence. Tenma is the registered trademark of the Group. © Premier Farnell Limited 2016.Part Number TableDescriptionPart Number Digital Multimeter, Handheld 72-2605Digital Multimeter, Handheld 72-10405Digital Multimeter, Handheld 72-2610True RMS Digital Multimeter, Handheld 72-10410True RMS Digital Multimeter, Handheld72-10415。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
一、产品简介1.1 引用标准引用国家标准GB/T 17883-1999 0.2S 级和0.5S 级静止式交流有功电度表GB/T 17882-1999 2 级和3 级静止式交流无功电度表GB/T 15284-2002 多费率电能表特殊要求DL/T 614-1997 多功能电能表GB/T13850-1998 交流电量转换为模拟量或者数字信号的电测量变送器相应国际标准IEC 62053-22:2003 电量测量设备(交流)-特殊要求-第22 部分:静态电度表(0.2S 和0.5S 级)IEC 62053-23:2003 电量测量设备(交流)-特殊要求-第23 部分:静态无功表(2S 和3S 级)IEC 61010-1:2001 测量,控制以及实验室用电气设备的安全要求-第1 部分:一般要求IEC 61000-2-11 电磁兼容性(EMC)-第2-11 部分IEC 60068-2-30 环境测试-第2-30 部分1.2 产品概述数显多功能电力仪表是针对电力系统、工矿企业、公共设施、智能大厦等的电力智能监控和电能计量等需求而设计,能够高精度测量三相电网中的所有常用电力参数,三相电压,三相电流,有功功率,无功功率,视在功率,频率,功率因数,四象限电能,UIPQ 需量,模拟量输入监测,开关量输入监测,并带有通讯接口,模拟量输出,继电器输出控制,电能脉冲输出等功能。
数显多功能电力仪表具备多种扩展功能的输入输出方式可供选择:2 路通讯接口、4 路模拟量输出、4 路继电器输出、本地或远程的开关信号监测和控制输出功能( 遥信和遥控功能)、12 路开关监测、2 路模拟量输入测量、2 路电能脉冲输出、事件记录功能。
数显多功能电力仪表具有极高的性能价格比,可以直接取代常规电力变送器,测量指示仪表,电能计量仪表以及相关的辅助单元。
作为一种先进的智能化,数字化的电网前端采集元件,已广泛应用于各种控制系统,SCADA 系统和能源管理系统,变电站自动化,配电网自动化,小区电力监控,工业自动化,智能建筑,智能型配电盘,开关柜中,具有安装方便,接线简单,维护方便,工程量小,现场可编程设置输入参数等特点,能够完成业界不同PLC,工业控制计算机通讯软件的组网。
三相四线Y34/三相三线V33持续:1.2倍 瞬时:2倍持续:1.2倍 瞬时:2倍AC/DC 80~270V <5VA无源光耦集电极输出固定脉宽 80mS±20%Rs485通讯接口,物理层隔离符合国际标准的MODBUS-RTU 协议通讯速度4800~38400校验方式N81,E81,O810/4~20mA 或0~5/10V 变送输出可编程设置变送项目和对应值可编程遥控/报警继电器输出容量5A/250VAC 5A/30VDC可编程报警电量,开关输入,模拟输入或者遥控方式遥测开关输入测量,无源干结点输入可编程关联报警输出0/4~20mA 模拟量输入测量可编程报警输出电量:0.5 频率:±0.1Hz 有功电能:0.1S 无功电能:0.5模拟输入:0.5数码显示:3排12个高亮度数码管工作温度:-10-55 C 储存温度:-20-75 C绝缘:信号,电源,输出端子对壳电阻>5MΩ耐压,信号输入,电源,输出间>AC2KV尺寸:42型:120*120*106mm 96型:96*96*95mm 3型:80*80*81 A型:72*72*67mm重量:42型:0.6KG 96型:0.5KG 3型:0.3KG A型:0.2KG接线电压电流信号输入频率量程过载功耗量程过载功耗400V/100V<1VA 5A/1A<1VA 40~65 Hz 电源电能脉冲通讯模拟输出继电器输出遥测开关模拟输入测量等级显示方式环境安全外形参数三、技术参数°°4.1 仪表尺寸安装尺寸:a×b 开孔尺寸:s×y面板尺寸:l×h (单位mm)外 形代 号 外形尺寸(l×h)Unit(mm)屏装配合尺寸 (a×b)Unit(mm) 开 孔 尺 寸(s×y)Unit(mm)最小安装距离总长(N)(mm)水平(mm)垂直(mm)42963A120×12096×9680×8072x72110×11090×9075×7566×66111×11191×9176×7667×671209680721209680721149689784. 2 安装方法前视图后视图四、安装与接线1) 在固定配电柜开s×y(mm)的孔;2) 取出仪表,松开螺丝,取下固定支架;3) 仪表由前安入安装孔;4) 插入仪表固定支架,并拧紧螺丝固定仪表。
接线说明:(a) 电压输入:输入电压不要高于产品的额定输入电压(100V 或400V),否则应考虑使用PT,为了便于维护,建议使用接线排.(b) 电流输入:标准额定输入电流为5A,大于5A 的情况应使用外部CT.如果使用的CT 上连有其它仪表,接线应采用串接方式,去除产品的电流输入连线之前,一定要先断开CT 一次回路或者短接二次回路,为便于维护建议使用接线排.(c )要确保输入电压,电流相对应,相序一致,方向一致;否则会出现数值和符号错误!(功率和电能).(d)仪表可以工作在三相四线方式或者三相三线方式,用户应根据现场使用情况选择相应的接线方式.一般在没有中心线的情况下使用三相三线方式.在有中心线的情况下使用三相四线方式,三相三线可以只安装2 个CT(A 和C 相),三相四线需要安装三个CT(在只有2CT 情况下可以合成另一相电流).注意:仪表内可设置两种接线方式,实际接线方式和表内设置方式必须一致,否则仪表的测量数据不准确.注:具体接线方式,脉冲常数等技术参数以产品随机接线图为准.五、产品端子示意图96型端子示意图显示信息测量信息有7页(默认disp 设置为ALL即关闭循环显示,设置为其他时,则通电时优先显示设置项),可用“ ”,“ ”进行页面切换,用“ ”进行同页信息.每页信息切换如下表所示.说明:以上界面为功能最全的示意图,如实物不具备某项功能则不显示。
八、功能模块8.1 通讯8.1.1 物理层1) RS485 通讯接口,异步半双工模式;2) 通讯速度4800~38400bps 可设置,出厂默认为9600 bps;3)字节传送格式:1 位起始位,8 位数据位,1 位校验位,2-3 位停止位(N81 E81 O81)可选;8.1.2 通讯协议 MODBUS-RTUMODBUS 协议在一根通讯线采用主从应答方式的通讯连接方式。
主机的信号寻址到一台唯一地址的从机,从机发出的应答信号以相反的方向传输给主机,即在一根单独的通讯线,信号沿着相反的两个方向传输所有的通讯数据流(半双工的工作模式)。
MODBUS 协议只允许在主机(PC,PLC 等)和终端设备之间通讯,而不允许独立的终端设备之间的数据交换,这样各终端设备不会在它们初始化时占据通讯线路,而仅限于响应到达本机的查询信号。
地址命令起始寄存器地址(高位)起始寄存器地址(低位)寄存器个数 (低位)寄存器个数 (高位) CRC16 高位 CRC16 低位0CH10H00H04H00H01H41H15H响应数据帧(从机),表明数据已写入。
地址命令起始寄存器地址(高位)起始寄存器地址(低位)寄存器个数 (高位)寄存器个数(低位)CRC16 低位 CRC16 高位 写入字节数 写入数据0CH 10H 00H 04H 00H 01H 02H00H50HFFH78H查询数据帧(主机)预置数据(功能码:16):此功能允许用户改变多个寄存器的内容(电度量可用此功能号写入,需要强调的是所写入的数据为可写属性参数,个数不超过地址范围,下面的例子是写入电流变比为 400A/5A=80 通讯方式地址命令0CH03H数据字节 长度数据 1 2 3 4 5 6CRC16 低位 CRC16 高位06H72HE5H13H 80H 13H 90H 13H 70H响应数据帧(从机),表明Ia=1380H(4.992),Ib=1390H(5.008),Ic=1370H(4.976).地址命令起始寄存器地址(高位)起始寄存器地址(低位)寄存器个数 (低位)寄存器个数 (高位) CRC16 高位 CRC16 低位0CH03H00H2BH00H03H74HDEH查询数据帧(主机)MODBUS地址信息表地址项目描述字节地址说明设置信息0MM编程设置密码0,12字节,1-99991DZTXK仪表地址21字节,1-247见位地址说明通讯控制字32XS1SRS电量显示选择输入控制字45电量显示方式,0-6见位地址说明3 4PTCT电压倍率电流倍率6,78,9PT=电压1次侧/2次侧(1-9999)CT=电流1次侧/2次侧(1-9999)5 6 7 8 9 10DOS1DOS2DOS3DOS4开关量输出1设置开关量输出2设置开关量输出3设置开关量输出4设置10,11,1213,14,1516,17,1819,20,21见开关量模块部分描述11 12 13 14 15 16MNS1MNS2MNS3MNS4模拟量输出1设置模拟量输出1设置模拟量输出1设置模拟量输出1设置22,23,2425,26,2728,29,3031,32,33见模拟量模块部分描述17LIGHTAUTOLED显示亮度自动抄表日期34351:最暗,15:最亮自动抄表日 1-3118 19 20 21 22 23 24 25 26 27 28 29SDS1SDS2SDS3SDS4SDS5SDS6SDS7SDS8时段设置1时段设置2时段设置3时段设置4时段设置5时段设置6时段设置7时段设置836,37,3839,40,4142,43,4445,46,4748,49,5051,52,5354,55,5657,58,59见复费率模块部分描述运 行 信 息30 31 32 3334 35 36DATETIMEDIOINFOAIDPTDCTDPQSIGN日期时间开关量信息运行信息模拟量输入电压小数点位置电流小数点位置功率小数点位置功率符号位60,61,6263,64,65666768,6970717273YY-MM-DDHH-MM-SS见开关量模块说明保留保留见数据格式描述地址项目描述字节地址说明电 量 信 息Ua 74,75Ub Uc Uab Ubc Uca Ia 61电 能 信 息37383940414243444546474849525051535455565758596062Ib Ic Pa Pc Pb Ps Qa Qc Qb Qs PFa PFc PFb PFs Sa Sc Sb Ss FRA相电压B相电压C相电压AB线电压BC线电压CA线电压A相电流B相电流C相电流A相有功功率B相有功功率C相有功功率总有功功率A相无功功率B相无功功率C相无功功率总无功功率A相功率因数B相功率因数C相功率因数总功率因数A相视在功率B相视在功率C相视在功率总视在功率频率76,7778,7980,8182,8384,8586,8788,8990,9192,9394,9596,9798,99100,101102,103104,105106,107108,109110,111112,113114,115116,117118,119120,121122,123124,12563646566676869707172737475767778WPP WPN WQP WQN EPP EPN EQP EQN正向有功电能负向有功电能负向无功电能正向无功电能正向有功电能负向有功电能负向无功电能正向无功电能126,127,128,129130,131,132,133134,135,136,137138,139,140,141142,143,144,145146,147,148,149150,151,152,153154,155,156,157数据格式描述:采用2字节电量寄存器(0-9999)和1字节小数点寄存器(0-15)描述电量数据。