常见数控机床报警信息(中英文对照),太全啦!
数控机床中英文对照表
数控机床中英文对照表ABS和REL——在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标ALL——全选，程序编辑时用PRGRM——程序（program）的缩写，用于查看程序NEXT——查看程序和查看参数时，下一页OPRT——在法那克系统中，选择编辑程序时，也就是按下PRGRM后，再按这个键，才能输入程序号HOST，CONECT——这两个是在系统与外界通信时用的，我没试过，不知道什么作用HELP——查看帮助信息SHIFT——换档键，有些键有两个字符，按下这个键，用来输入顶部那个字符ALTER——程序修改键，编辑程序时用INSERT——程序插入键，编辑程序时用EOB——程序结束符，在编辑程序时，没段程序结束时，要加这个符号CAN——取消键，用来取消输入INPUT——输入键，用来输入程序或参数POS——按此键显示当前机床位置画面PROS——按此键显示当前程序画面OFFSET——按此键显示刀具偏置画面SETTING——按此键显示刀具偏置设定画面SYSTEM——按此键显示系统信息及系统状态画面GRAPH——按此键显示加工时刀具轨迹的图形画面CUSTOM——按此键显示用户宏程序画面手动数据输入(MDI)直接数字控制方法(DNC)控制器单元或机控制器单元（MCU）法拉克：ALTER 修改程序及代码INSRT 插入程序DELET 删除程序EOB 完成一句(END OF BLOCK)CAN 取消(EDIT 或MDI MODE 情况下使用)INPUT 输入程序及代码OUTPUT START 输出程序及指令OFFSET 储存刀具长度、半径补当值AUX GRAPH 显示图形PRGRM 显示程序内容ALARM 显示发生警报内容或代码POS 显示坐标DGONS PARAM 显示自我诊断及参数功能RESET 返回停止CURSOR 光标上下移动PAGE 上下翻页常见机床报警信息中英文对照T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z 轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL（X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD （刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警)MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR MAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALARM(气压低报警)MOTOR OVERLOAD(电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERRORDOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误)SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCKTRY TO RUN SPINDLE WHILE TAIL NOT LOCKSPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭) SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ONHYDRAULIC MOTOR QF7 OFF（液压马达QF7关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED（液压过滤器阻止）HYDRAULIC OIL LEVEL LOW（液压油位低）HYDRAULIC FAN QF8 OFF（液压风扇QF8关闭）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF（冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK（内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF（内冷却液QF13关闭）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW（低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW（润滑油低）DOOR OPEN（门打开）FRONT DOOR(R) OPEN（前门打开）LEFT DOOR OPEN（左门打开）LUBRICATION OIL QF23 OFF（润滑油QF23关闭）LUBRICATION PRESS LOW（润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED（门没有全部关闭）IN M06,MAG NOT READY（在M06，刀库未准备好）MAGAZINE NOT READY（刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZ NOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG 关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG 机床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTERY VOLTAGE IS LOW 探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE（参数写使能）PMC EDIT ENABLE（PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION 主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR 因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC电池SIEMENS常用缩略语A Output 输出ASCII American Standard Code for Information Interchange 美国信息交换标准代码AV Preparation for work 运行准备BA Operating mode 运行方式BAG Operating mode groups 运行方式组BB Ready for operation 准备好运行BCD Binary Coded Decimals 二-十进制BHG Hand-held terminal 手提终端BOF User interface 用户接口CNC Computerized Numerical Control 计算机化数字控制CP Communication Processor 通迅处理器CPU Central Processing Unit 计算机中央处理装置CR Carriage Return 托架折回CSB Central Service Board(PLC module) 中央维护板，PLC 模块CTS Clear To Send 发送使能DAU Digital-Analog Converter 数模转换器DB Data Block 数据块DIN German Industrial Standards 德国工业标准DIO Data Input/Output 数据输入/输出DRF Differential Resolver Function 差分功能DRY Dry Run 空运行DSB Decoding Single Block 译码单段DSR Data Send Ready 备用输入DW Data Word 数据字E Input 输入EIA-Code Special tape code,number of holes per characters alwaysodd 特殊纸带码，每个字符的孔数为奇数EPROM Programm memory with fixed program 有固定程序的程序存储器E/R Controlled Supply and Energy Recovery Module 可控电源和能量恢复模块ETC ETC key:Extension of the softkey bar in the same menuETC 键：同级菜单扩展键FDB Product designation database 产品指定数据库FIFO First in First Out 先进先出FRA Frame module 帧频模块FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging 坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compensation 铣刀半径补偿FST Feed Stop 停止进给GUD Global User Data 全体用户数据HMS High-Resolution Measuring System 高分辨率测量系统HSA Main Spindle Drive 主轴驱动HW Hardware 硬件IM Interface Module 接口模块IM-S/R Interface Module(S=send/R=receive) 接口模块，S=发送/R=接收INC Increment 步进增量ISO-Code Special tape code,number of holes per character always even特殊纸带码，每个字符的孔数为偶数K1...k4 Channel 1 to Channel 4 通道1 到通道4KOP Ladder Diagram 梯形图KV Loop-Gain Factor 增益系数KUE Transformation Ratio 传动比LCD Liquid Crystal Display 液晶显示LED Light Emitting Diode 发光二极管显示LUD Local User Data 局部用户数据MB Megabyte 兆字节MD Machine Data 机床数据MK Measuring Circuit 测量回路MDA Manual Data Automatic 手动输入，自动执行MLFB Machine-readable product designation 机器可识别的产品代号MMC Man Machine Communication:User interface of the numerical controlsystem for operation,programming and simulation 人机通讯：系统操作界面，用操作，编程和模拟MPF Main Program File：NC part program(main program)NC 零件程序，主程序MPI Multi Point Interface 多点通讯接口MSTT Machine control panel 机床控制面板NC Numerical Control 数字控制NCK Numerical Control Kernel(numerical krnel with block preparation, traversing range etc.) 数字控制核心：具有程序段预处理,运行范围等等NCU Numerical Control Unit 数控单元NURBS Non Uniform Rational B Spline 非均值有理B样条NV Zero Offset 零点偏置OEM Original Equipment Manufacturer 原设备制造商OP Operator Panel 操作面板OPI Operator Panel Interface 操作面板接口PC Personal Comprter 个人计算机PCMCIA Personal Computer Menory Card International Association接口协议PG Programming Device 编程器PLC Programmable Logic Control 可编程逻辑控制器PRT Program Test 程序测试RAM Random Access Memory 随机存取存储器RISC Reduced Instruction Set Computer 处理器，具有指令组小、通过能力强ROV Rapid Override 快速修调RPA R Parameters Active(NCK memoty area for R parameter numbers) R 参数有效，NCK 中用于R 参数号的存储器区RTS Request To Send(control signal from serial data interfaces)发送请求：来自串行接口的控制信号SBL Single Block 单段SBL2 Single Block Decoding 译码单段SEA Setting Data Active(memory area for setting data in NCK)设定数据有效：用于NCK 中设定数据的存储区SD Setting Data 设定数据SKP Skip Block 程序段跳跃SM Signal Module 信号模块SPF Sub Program File 子程序文件SPS Programmable Logic Controller 可编程逻辑控制器SRK Cutter Radius Compensation 刀尖半径补偿SSFK Leadscrew Error Compensation 丝杠螺距误差补偿SSI Serial Synchronous Interface 串行同步接口SW Software 软件TEA Testing Data Active(with reference to the machine data) 测试数据有效：与机床数据有关TO Tool Offset 刀具补偿TOA Tool Offset Active(memory area for tool offset) 刀具补偿有效，用于刀补的存储区TRANSMIT Transform Milling into Turning(coordinate conversion on turning machines for milling)铣床转换为车床：车床坐标换算用于铣削加工VSA Feed drive(spindle) 主轴进给驱动V Bit type PLC variable PLC变量类型：位VB Byte type PLC variablePLC变量类型：字节WKZ Tool 刀具WZ Tool 刀具WZK Tool offset 刀具补偿ZOA Zero Offset Active(memory area for zero offsets) 零点偏置有效：零点偏置存储区。
机床按键与报警显示中英对照
法拉克：ALTER 修改程序及代码INSRT 插入程序DELET 删除程序EOB 完成一句 (END OF BLOCK)CAN 取消(EDIT 或 MDI MODE 情况下使用) INPUT 输入程序及代码OUTPUT START 输出程序及指令OFFSET 储存刀具长度、半径补当值AUX GRAPH 显示图形PRGRM 显示程序容ALARM 显示发生警报容或代码POS 显示坐标DGONS PARAM 显示自我诊断及参数功能RESET 返回停止CURSOR 光标上下移动PAGE 上下翻页数控机床中英文对照表ABS和REL——在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标ALL——全选，程序编辑时用PRGRM——程序（program）的缩写，用于查看程序NEXT——查看程序和查看参数时，下一页OPRT——在法那克系统中，选择编辑程序时，也就是按下PRGRM后，再按这个键，才能输入程序号HOST，CONECT——这两个是在系统与外界通信时用的，我没试过，不知道什么作用HELP——查看帮助信息SHIFT——换档键，有些键有两个字符，按下这个键，用来输入顶部那个字符ALTER——程序修改键，编辑程序时用INSERT——程序插入键，编辑程序时用EOB——程序结束符，在编辑程序时，没段程序结束时，要加这个符号CAN——取消键，用来取消输入INPUT——输入键，用来输入程序或参数POS——按此键显示当前机床位置画面PROS——按此键显示当前程序画面OFFSET——按此键显示刀具偏置画面SETTING——按此键显示刀具偏置设定画面SYSTEM——按此键显示系统信息及系统状态画面GRAPH——按此键显示加工时刀具轨迹的图形画面CUSTOM——按此键显示用户宏程序画面手动数据输入 (MDI)直接数字控制法 (DNC)控制器单元或机控制器单元（MCU常见机床报警信息中英文对照T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL（X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD （刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警) MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERRORMAGAZINE NOT IN POSITION OR SENSOR ERROR AIR PRESSURE LOW ALARM(气压低报警) MOTOR OVERLOAD(电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERRORDOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误) SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCK TRY TO RUN SPINDLE WHILE TAIL NOT LOCK SPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭)SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ONHYDRAULIC MOTOR QF7 OFF（液压马达QF7关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED（液压过滤器阻止）HYDRAULIC OIL LEVEL LOW（液压油位低）HYDRAULIC FAN QF8 OFF（液压风扇QF8关闭）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF（冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK（冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF（冷却液QF13关闭）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW（低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW（润滑油低）DOOR OPEN（门打开）FRONT DOOR(R) OPEN（前门打开）LEFT DOOR OPEN（左门打开）LUBRICATION OIL QF23 OFF（润滑油QF23关闭）LUBRICATION PRESS LOW（润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED（门没有全部关闭）IN M06,MAG NOT READY（在M06，刀库未准备好）MAGAZINE NOT READY（刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZNOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG 关于MAG的K 参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG 机床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTERY VOLTAGE IS LOW 探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE（参数写使能）PMC EDIT ENABLE（PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION 主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR 因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC电池SIEMENS常用缩略语A Output 输出ASCII American Standard Code for Information Interchange 美国信息交换标准代码AV Preparation for work 运行准备BA Operating mode 运行式BAG Operating mode groups 运行式组BB Ready for operation 准备好运行BCD Binary Coded Decimals 二-十进制BHG Hand-held terminal 手提终端BOF User interface 用户接口CNC Computerized Numerical Control 计算机化数字控制CP Communication Processor 通迅处理器CPU Central Processing Unit 计算机中央处理装置CR Carriage Return 托架折回CSB Central Service Board(PLC module) 中央维护板，PLC 模块CTS Clear To Send 发送使能DAU Digital-Analog Converter 数模转换器DB Data Block 数据块DIN German Industrial Standards 德国工业标准DIO Data Input/Output 数据输入/输出DRF Differential Resolver Function 差分功能DRY Dry Run 空运行DSB Decoding Single Block 译码单段DSR Data Send Ready 备用输入DW Data Word 数据字E Input 输入EIA-Code Special tape code,number of holes per characters always odd 特殊纸带码，每个字符的数为奇数EPROM Programm memory with fixed program 有固定程序的程序存储器E/R Controlled Supply and Energy Recovery Module 可控电源和能量恢复模块ETC ETC key:Extension of the softkey bar in the same menuETC 键：同级菜单扩展键FDB Product designation database 产品指定数据库FIFO First in First Out 先进先出FRA Frame module 帧频模块FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging 坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compensation 铣刀半径补偿FST Feed Stop 停止进给GUD Global User Data 全体用户数据HMS High-Resolution Measuring System 高分辨率测量系统HSA Main Spindle Drive 主轴驱动HW Hardware 硬件IM Interface Module 接口模块IM-S/R Interface Module(S=send/R=receive) 接口模块，S=发送/R=接收INC Increment 步进增量ISO-Code Special tape code,number of holes per character always even特殊纸带码，每个字符的数为偶数K1...k4 Channel 1 to Channel 4 通道1 到通道4KOP Ladder Diagram 梯形图KV Loop-Gain Factor 增益系数KUE Transformation Ratio 传动比LCD Liquid Crystal Display 液晶显示LED Light Emitting Diode 发光二极管显示LUD Local User Data 局部用户数据MB Megabyte 兆字节MD Machine Data 机床数据MK Measuring Circuit 测量回路MDA Manual Data Automatic 手动输入，自动执行MLFB Machine-readable product designation 机器可识别的产品代号MMC Man Machine Communication:User interface of the numerical controlsystem for operation,programming and simulation 人机通讯：系统操作界面，用操作，编程和模拟MPF Main Program File：NC part program(main program)NC 零件程序，主程序MPI Multi Point Interface 多点通讯接口MSTT Machine control panel 机床控制面板NC Numerical Control 数字控制NCK Numerical Control Kernel(numerical krnel with block preparation,traversing range etc.) 数字控制核心：具有程序段预处理,运行围等等NCU Numerical Control Unit 数控单元NURBS Non Uniform Rational B Spline 非均值有理B样条NV Zero Offset 零点偏置OEM Original Equipment Manufacturer 原设备制造商OP Operator Panel 操作面板OPI Operator Panel Interface 操作面板接口PC Personal Comprter 个人计算机PCMCIA Personal Computer Menory Card International Association 接口协议PG Programming Device 编程器PLC Programmable Logic Control 可编程逻辑控制器PRT Program Test 程序测试RAM Random Access Memory 随机存取存储器RISC Reduced Instruction Set Computer 处理器，具有指令组小、通过能力强ROV Rapid Override 快速修调RPA R Parameters Active(NCK memoty area for R parameter numbers)R 参数有效，NCK 中用于R 参数号的存储器区RTS Request To Send(control signal from serial data interfaces)发送请求：来自串行接口的控制信号SBL Single Block 单段SBL2 Single Block Decoding 译码单段SEA Setting Data Active(memory area for setting data in NCK)设定数据有效：用于NCK 中设定数据的存储区SD Setting Data 设定数据SKP Skip Block 程序段跳跃SM Signal Module 信号模块SPF Sub Program File 子程序文件SPS Programmable Logic Controller 可编程逻辑控制器SRK Cutter Radius Compensation 刀尖半径补偿SSFK Leadscrew Error Compensation 丝杠螺距误差补偿SSI Serial Synchronous Interface 串行同步接口SW Software 软件TEA Testing Data Active(with reference to the machine data) 测试数据有效：与机床数据有关TO Tool Offset 刀具补偿TOA Tool Offset Active(memory area for tool offset) 刀具补偿有效，用于刀补的存储区TRANSMIT Transform Milling into Turning(coordinate conversion onturning machines for milling)铣床转换为车床：车床坐标换算用于铣削加工VSA Feed drive(spindle) 主轴进给驱动..V Bit type PLC variable PLC变量类型：位VB Byte type PLC variablePLC变量类型：字节WKZ Tool 刀具WZ Tool 刀具WZK Tool offset 刀具补偿ZOA Zero Offset Active(memory area for zero offsets) 零点偏置有效：零点偏置存储区Word资料.。
机床按键与报警显示中英对照
机床按键与报警显示中英对照法拉克：ALTER 修改程序及代码 INSRT 插入程序 DELET 删除程序EOB 完成一句 (END OF BLOCK) CAN 取消(EDIT 或 MDI MODE 情况下使用) INPUT 输入程序及代码 OUTPUT START 输出程序及指令 OFFSET 储存刀具长度、半径补当值 AUX GRAPH 显示图形 PRGRM 显示程序内容 ALARM 显示发生警报内容或代码POS 显示坐标 DGONS PARAM 显示自我诊断及参数功能 RESET 返回停止 CURSOR 光标上下移动 PAGE 上下翻页—欢迎下载 2 数控机床中英文对照表 ABS 和 REL——在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标 ALL——全选，程序编辑时用 PRGRM——程序（program）的缩写，用于查看程序 NEXT——查看程序和查看参数时，下一页 OPRT——在法那克系统中，选择编辑程序时，也就是按下 PRGRM 后，再按这个键，才能输入程序号HOST，CONECT——这两个是在系统与外界通信时用的，我没试过，不知道什么作用 HELP——查看帮助信息 SHIFT——换档键，有些键有两个字符，按下这个键，用来输入顶部那个字符ALTER——程序修改键，编辑程序时用 INSERT——程序插入键，编辑程序时用 EOB——程序结束符，在编辑程序时，没段程序结束时，要加这个符号 CAN——取消键，用来取消输入INPUT——输入键，用来输入程序或参数 POS——按此键显示当前机床位置画面 PROS——按此键显示当前程序画面OFFSET——按此键显示刀具偏置画面 SETTING——按此键显示刀具偏置设定画面—欢迎下载 3 SYSTEM——按此键显示系统信息及系统状态画面 GRAPH——按此键显示加工时刀具轨迹的图形画面CUSTOM——按此键显示用户宏程序画面手动数据输入 (MDI) 直接数字控制方法 (DNC) 控制器单元或机控制器单元（MCU —欢迎下载 4 常见机床报警信息中英文对照 T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T 代码出错，非法 T 代码）M CODE ERROR （M 代码出错，非法 M 代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC 没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流 24 断开）+24V NOT READY（+24V 没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）—欢迎下载 5 AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z 轴未回零）4TH ZERO POINT NOT REACHED （第 4 轴未回零）X AXIS OVERTRAVL（X 轴超限）Y AXIS OVERTRAVL （Y 轴超限）Z AXIS OVERTRAVL （Z 轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z 轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）—欢迎下载 6 DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）—欢迎下载 7 AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD （刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）—欢迎下载 8 LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警) NC BATTERY LOW ALARM(NC 电池低报警) MAGAZINE MOVE LIMIT SWITCH ERROR SPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR MAGAZINE NOT IN POSITION OR SENSOR ERROR AIR PRESSURE LOW ALARM(气压低报警) MOTOR OVERLOAD(电机过载) TCODE > MAGAZINE TOOLS T CODE < 1 ERROR 5TH AXIS HARDWARE OVERTRAVER LIMIT ERROR DOOR IS OPENED(开门) LUB PRESSURE SWITCH ERROR(油压开关错误) SPINDLE OIL COOLANT UNIT ERROR SPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFF—欢迎下载 9 HYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPT TRY TO RUN SPINDLE WHILE CHUCK NOT LOCK TRY TO RUN SPINDLE WHILE TAIL NOT LOCK SPINDLE NEUTRAL GEAR MAGAZINE ADJUST HYDRAULIC NOT RUN SAFETY DOOR BE OPENED SAFETY DOOR NOT CLOSE NOT ALL AXIS HAVE GONE BACK REF IN ADJUST,IGNORE GOING BACK REF AFTER EXCHANGE TOOL,CYCLE START ATC MOTOR QF16 OFF X AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）—欢迎下载 10 SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇 QF26 关闭) SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARD SPINDLE TOOL NOT CLAMP SPINDLE TOOL NOT UNCLAMP MAG NOT IN POSITION MAG DOES NOT ROTATE MAG DOES NOT STOP RUNNING A AXIS HAVE NOT CLAMPED A AXIS HAVE NOT UNCLAMPED SETD499=1,“MAG.JOG“ SWITCH ON HYDRAULIC MOTOR QF7 OFF （液压马达 QF7 关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED（液压过滤器阻止）HYDRAULIC OIL LEVEL LOW（液压油位低）—欢迎下载 11 HYDRAULIC FAN QF8 OFF（液压风扇 QF8 关闭）HELIX CONYER QF9 OR QF10 OFF CHAIN CONYER QF11 OFF COOLANT MOTOR QF12 OFF（冷却液电机 QF12 关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTES INNER COOLANT BLOCK（内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主轴冷却液电机QF14 关闭）INNER COOLANT QF13 OFF（内冷却液 QF13 关闭）MAG MOTOR QF15 OFF CABINET COOLANT EQUIP QF20 OFF OIL GATHER QF24 OFF AIR PRESSURE LOW（低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW（润滑油低）DOOR OPEN（门打开）FRONT DOOR(R) OPEN（前门打开）LEFT DOOR OPEN（左门打开）LUBRICATION OIL QF23 OFF（润滑油 QF23 关闭）LUBRICATION PRESS LOW（润滑油位低）—欢迎下载 12 IN ADJUST,MAG CAN"T EXCHANGE T（在调整，刀库不能交换 T）NOT ALL DOOR CLOSED（门没有全部关闭）IN M06,MAG NOT READY（在 M06，刀库未准备好）MAGAZINE NOT READY（刀库未准备好）POCKET NOT HORIZANTAL IN M06,Z NOT BACK TO 2ND REF IN M06,Z AXIS NOT IN PSW1 ATC NOT IN ZERO POSITION SPINDLE ORIENTATION UNCOMPLETE POCKET NOT HOR./MAG NOT BCKWRD POCKET NOT VER./MAG NOT FORWRD UNCLAMP TOOL HAS NOT COMPLETED CLAMP TOOL HAS NOT COMPLETED AIM TOOL NO. IS WRONG MAG NOT BACKWARD AFTER RETRACT,SET R.T.BACK OFF ZNOT IN PSW2,FORBID ATC RUNNING D499 EQUAL 1 MAG.JOG SOFT SWITCH IS ON Z NOT IN PSW2,FORBID MAG FORWARD—欢迎下载 13 CHEKE SPINDLE MODULE ALARM OIL WATER SEPARATOR QF24 OFF SET THE SOFT SWITCH MAG.JOG OFF SET D499 TO 0 设定 D499 为 0 K PARAM ABOUT MAG SET IS WRONG 关于 MAG 的 K 参数设定错误 MECHANICAL BRAKE NOT RELEASED 机床抱闸没有松开 MECHANICAL BRAKE IS WRONG 机床抱闸错误 PLEASE ADD LUB.OIL 请加润滑油 PROBE BATTERY VOLTAGE IS LOW 探头电池电压低 PROBE IS ERR 探头错误 PARAMETER WRITE ENABLE（参数写使能）PMC EDIT ENABLE（PMC 编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主轴档位信号消失T_CLAMPED_SIGNAL MISS T 夹紧信号消失 SP OVERRIDE SWITCH DISCONNECTION 主轴倍率开关断路 FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路 THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR 因为缺少压空交换停止—欢迎下载 14 THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷却水少立即加水 COOLANT LEVEL LOW,ADD COOLANT WATER 冷却水液位低 PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换 CNC电池 SIEMENS 常用缩略语A Output 输出ASCII American Standard Code for Information Interchange 美国信息交换标准代码AV Preparation for work 运行准备BA Operating mode 运行方式BAG Operating mode groups 运行方式组BB Ready for operation 准备好运行BCD Binary Coded Decimals 二-十进制BHG Hand-held terminal 手提终端BOF User interface 用户接口CNC Computerized Numerical Control 计算机化数字控制CP Communication Processor 通迅处理器CPU Central Processing Unit 计算机中央处理装置CR Carriage Return 托架折回CSB Central Service Board(PLC module) 中央维护板，PLC 模块—欢迎下载 15 CTS Clear To Send 发送使能DAU Digital-Analog Converter 数模转换器DB Data Block 数据块DIN German Industrial Standards 德国工业标准DIO Data Input/Output 数据输入/输出DRF Differential Resolver Function 差分功能DRY Dry Run 空运行DSB Decoding Single Block 译码单段DSR Data Send Ready 备用输入DW Data Word 数据字E Input 输入EIA-Code Special tape code,number of holes per characters always odd 特殊纸带码，每个字符的孔数为奇数EPROM Programm memory with fixed program 有固定程序的程序存储器E/R Controlled Supply and Energy Recovery Module 可控电源和能量恢复模块ETC ETC key:Extension of the softkey bar in the same menuETC 键：同级菜单扩展键FDB Product designation database 产品指定数据库FIFO First in First Out 先进先出—欢迎下载 16 FRA Frame module 帧频模块FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging 坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compensation 铣刀半径补偿FST Feed Stop 停止进给GUD Global User Data 全体用户数据HMS High-Resolution Measuring System 高分辨率测量系统HSA Main Spindle Drive 主轴驱动HW Hardware 硬件IM Interface Module 接口模块IM-S/R Interface Module(S=send/R=receive) 接口模块，S=发送/R=接收INC Increment 步进增量ISO-Code Special tape code,number of holes per character always even特殊纸带码，每个字符的孔数为偶数K1...k4 Channel 1 to Channel 4 通道 1 到通道 4KOP Ladder Diagram 梯形图KV Loop-Gain Factor 增益系数—欢迎下载 17 KUE Transformation Ratio 传动比LCD Liquid Crystal Display 液晶显示LED Light Emitting Diode 发光二极管显示LUD Local User Data 局部用户数据MB Megabyte 兆字节MD Machine Data 机床数据MK Measuring Circuit 测量回路MDA Manual Data Automatic 手动输入，自动执行MLFB Machine-readable product designation 机器可识别的产品代号MMC Man Machine Communication:User interface of the numerical controlsystem for operation,programming and simulation 人机通讯：系统操作界面，用操作，编程和模拟MPF Main Program File：NC part program(main program)NC 零件程序，主程序MPI Multi Point Interface 多点通讯接口MSTT Machine control panel 机床控制面板NC Numerical Control 数字控制NCK Numerical Control Kernel(numerical krnel with block preparation,—欢迎下载 18 traversing range etc.) 数字控制核心：具有程序段预处理,运行范围等等NCU Numerical Control Unit 数控单元NURBS Non Uniform Rational B Spline 非均值有理 B 样条NV Zero Offset 零点偏置OEM Original Equipment Manufacturer 原设备制造商OP Operator Panel 操作面板OPI Operator Panel Interface 操作面板接口PC Personal Comprter 个人计算机PCMCIA Personal Computer Menory Card International Association 接口协议PG Programming Device 编程器PLC Programmable Logic Control 可编程逻辑控制器PRT Program Test 程序测试RAM Random Access Memory 随机存取存储器RISC Reduced Instruction Set Computer 处理器，具有指令组小、通过能力强ROV Rapid Override 快速修调RPA R Parameters Active(NCK memoty area for R parameter numbers)R 参数有效，NCK 中用于 R 参数号的存储器区—欢迎下载 19 RTS Request To Send(control signal from serial data interfaces)发送请求：来自串行接口的控制信号SBL Single Block 单段SBL2 Single Block Decoding 译码单段SEA Setting Data Active(memory area for setting data in NCK)设定数据有效：用于 NCK 中设定数据的存储区SD Setting Data 设定数据SKP Skip Block 程序段跳跃SM Signal Module 信号模块SPF Sub Program File 子程序文件SPS Programmable Logic Controller 可编程逻辑控制器SRK Cutter Radius Compensation 刀尖半径补偿SSFK Leadscrew Error Compensation 丝杠螺距误差补偿SSI Serial Synchronous Interface 串行同步接口SW Software 软件TEA Testing Data A ctive(with reference to the machine data) 测试数据有效：与机床数据有关TO Tool Offset 刀具补偿—欢迎下载 20 TOA Tool Offset Active(memory area for tool offset) 刀具补偿有效，用于刀补的存储区TRANSMIT Transform Milling into Turning(coordinate conversion onturning machines for milling)铣床转换为车床：车床坐标换算用于铣削加工VSA Feed drive(spindle) 主轴进给驱动V Bit type PLC variable PLC 变量类型：位VB Byte type PLC variablePLC 变量类型：字节WKZ Tool 刀具WZ Tool 刀具WZK Tool offset 刀具补偿ZOA Zero Offset Active(memory area for zero offsets)零点偏置有效：零点偏置存储区。
机床报警号中英文对照
ARM NUMBER ALARM DESCRIPTIONA000.0A000.1A000.2A000.3A000.4A000.5A000.6A000.7A001.0A001.1A001.2A001.3A001.4A001.5A001.6A001.7A002.0A002.1A002.2A002.3A002.4A002.5A002.6A002.7A003.0 1030 A3.0 HYDRAULIC MOTOR OVERLOAD 液压马达过载Hydraulic adj. 水力的, 水压的Hydraulic motor 液压马达, 液压[液力]发动机A003.1 1031 A3.1 MACHINE AIR PRESS SW FAIL 机器的空气压力失败空气压缩失败Machine n. 机器, 机械, 机动车辆, 机构, 设计, 机械般工作的人, (政党的)领导集团, 核心组织vt.机器制造, 用车床加工A003.2 1032 A3.2 MACH AIR FILTER CLOGGED 空气过滤器堵塞Mach 一种UNIX操作系统, 采用微内核技术Filter n. 滤波器, 过滤器, 滤光器, 筛选vt. 过滤, 渗透, 用过滤法除去vi. 滤过, 渗入, (消息等)走漏, 慢慢传开Clog n. 木底鞋, 障碍v. 障碍, 阻塞A003.3 1033 A3.3 HYD OIL LEVEL LOW 液压油的油压低HYD=Hydraulic Pressure 液压HYDAC=Hybrid Digital Analog Computer 混合数字模拟计算机A003.4 1034 A3.4 HYD OIL OVERTEMP 液压油的温度过热Overtemperature 过热(温度)A003.5 1035 A3.5 HYD OIL FILTER CLOGGED 液压油的过滤器堵塞A003.6 1036 A3.6 HYD PRESSURE FAIL 液压启动失败A003.7 1037 A3.7 HYD PRESS SWITCH ON WITH HYD OFF？？？关闭时？？？的压力开关却打开Switch n. 开关, 电闸, 转换vt. 转换, 转变Press Switch 压力(传动)开关A004.0 1040 A4.0 SPINDLE COMMISSIONING FAIL 主轴试运转失败Commis n.<法>小职员, 副手Commissioning 试运转；试车Commission n. 委任, 委托, 代办(权), 代理(权), 犯(罪), 佣金vt. 委任, 任命, 委托, 委托制作, 使服役A004.1 1041 A4.1 PMC FUNCT INSTRUCTION FAIL 电磁功能是指令失效PME=Photomagneto Electric Effect光电磁效应Function n. 官能, 功能, 作用, 职责, 典礼, 仪式, [数]函数vi. (器官等)活动, 运行, 行使职责Instruction n.指示, 用法说明(书), 教育, 指导, 指令A004.2 2142 A4.2 LOW CLASS ALM ACT 15 MIN ？？？？？？？？？Alm n. 救济品,高山草旬Min abbr. 1.部长(Minister) 2.部(Ministry)A004.3 5043 A4.3 PMC FUNCT INSTR FAIL, PATH2 STOP ？？？？？电磁功能是指令失效，路径2停止A004.4 5044 A4.4 ALARM SEV LEVEL 10, PATH2 STOP ？？？？？A004.5 1045 A4.5 TLCHG ALARM, STOP AT M06 EXECUTE ？？？？？TLCHG 报警，在M06处停止运行Execute vt. 执行, 实行, 完成, 处死, 制成,[律]经签名盖章等手续使(证书)生效A004.6 1046 A4.6 TOOL QUEUE COMMISSIONING FAIL 刀盘旋转失败A004.7 1047 A4.7 TOOL CHAIN COMMISSIONING FAIL 刀库链运转失败A005.0 1050 A5.0 24V POWER SUPPLY 1 FAIL ？？24V电压没有供给A005.1 1051 A5.1 24V POWER SUPPLY 2 FAIL ？？24V电压没有供给A005.2 1052 A5.2 REAR ACCESS DOOR OPENED 后门是开着的Rear n. 后面, 背后, 后方, 屁股adj. 后面的, 背面的, 后方的vt. 培养, 饲养, 举起, 树立, 栽种vi.高耸, 暴跳, 用后腿站起Access n. 通路, 访问, 入门vt. 存取, 接近A005.3 2153 A5.3 REAR ACCESS DOOR OPEN 后门没有关闭A005.4 1054 A5.4 TOOLCHANGE DOOR OPENED 刀库门是开着的A005.5 2155 A5.5 TOOLCHANGE DOOR OPEN 刀库门没有关闭A005.6 2156 A5.6 SERVO FANS CB OFF ？？伺服电机风扇没有运转Fan n. 扇子, 鼓风机, 风扇, 迷, 狂热者, 爱好者vt. 煽动, 刺激, 扇, 吹拂vi. 飘动, 成扇形散开Cincinnati Lamb 16−MC−04026 Page 12−5A005.7 1057 A5.7 EMERG STOP CONDITION ACTIVE 急停Emergency n. 紧急情况, 突然事件, 非常时刻, 紧急事件A006.0 2160 A6.0 OPER DOOR OPEN/UNLKOpe v. 开放, 自由进出A006.1 2161 A6.1 MODE NOT IN AUTO OR MDI 没有在AUTO和MDI方式下A006.2 1062 A6.2 OPER DOOR LOCKING FAIL OPER DOOR没有关紧A006.3 1063 A6.3 OPER DOOR UNLKED/OPNED OPER DOOR没有关A006.4 2164 A6.4 OPER DOOR UNLK FAILA006.5 2165 A6.5 FEEDHOLD IS ACTIVE ？？？？进给停止A006.6 1066 A6.6 OPER DOOR OPEN,INCYC/SP NOT OFFA006.7A007.0A007.1A007.2A007.3A007.4A007.5A007.6A007.7A008.0A008.1A008.2A008.3A008.4A008.5A008.6A008.7A009.0 2190 A9.0 PATH 1 AXIS UNREF F120A009.1 2191 A9.1 PATH 2 AXIS UNREF F1120A009.2A009.3A009.4A009.5A009.6A009.7A010.0 1100 A10.0 TRANSPORT DEVICE NOT ALIGNED ？？？？？Device n. 装置, 设计, 图案, 策略, 发明物, 设备[计]安装设备驱动程序Align vi. 排列vt. 使结盟, 使成一行A010.1 1101 A10.1 QUEUE DEVICE NOT ALIGNEDA010.2 2202 A10.2 MECH RET REQ−CYC INHA010.3 1103 A10.3 TOOLCHAIN DEVICE NOT ALIGNEDA010.4 1104 A10.4 XYZBA AXIS MOVER NOT ALIGNEDA010.5 1105 A10.5 INTERCHANGE ARM NOT ALIGNEDA010.6 1106 A10.6 INTERCHANGE DOOR NOT ALIGNEDA010.7 1107 A10.7 TOOLCHANGE DRIVER NOT ALIGNEDA011.0 1110 A11.0 INVALID M CODEA011.1A011.2A011.3A011.4A011.5Page 12−6 Cincinnati Lamb 16−MC−04026A011.6A011.7A012.0 1120 A12.0 CNTR CHIP COV OVLDA012.1 1121 A12.1 REAR LEAF CONV OVLDA012.2 1122 A12.2 REAR DRAG CONV OVLDA012.3 1123 A12.3 CNTR CHIP CONV RUN FAILA012.4 1124 A12.4 REAR LEAF CONV RUN FAILA012.5 1125 A12.5 REAR DRAG CONV RUN FAILA012.6 2226 A12.6 CHIP CONVS ST OP−AUTO SELA012.7 2227 A12.7 CHIP CONV STOP−CC OFF PBA013.0 2230 A13.0 SLD LUBE PS ACT AT START OF LUBEA013.1 2231 A13.1 SLD LUBE PS NOT PICKNG UPA013.2 2232 A13.2 SLD LUBE PS NOT DROPPING OUT A013.3A013.4A013.5A013.6A013.7A014.0A014.1A014.2A014.3A014.4A014.5A014.6A014.7A015.0 1150 A15.0 M81 FAIL, Z AXIS NOT RETRACTA015.1 1151 A15.1 M80 FAIL, AXES NOT IN PSNA015.2A015.3A015.4A015.5A015.6A015.7A016.0 1160 A16.0 B AXIS CLAMPING TIMEOUTA016.1 1161 A16.1 B AXIS UNCLAMPING TIMEOUTA016.2 1162 A16.2 B AXIS CLAMP PS DROPOUTA016.3 1163 A16.3 B AXIS UNCLAMP PS DROPOUTA016.4 2264 A16.4 B AXIS NOT CLP/UNCLP CYC INHA016.5A016.6 1166 A16.6 M10 AND B NOT EVEN DEGREESA016.7 2267 A16.7 B AXIS NOT CLAMPED CYC INHA017.0 1170 A17.0 SERVOS ENABLED FEEDBACK FAILA017.1 1171 A17.1 ASL60 ACTIVE FOR 2 MINUTESA017.2 1172 A17.2 SERV/SPDL CONTACT ON W/MACH OFF A017.3 1173 A17.3 Y MOTOR AXIS BRAKE NOT RELEASEDA017.4 5174 A17.4 TLCHAIN MOTOR BRAKE NOT RELEASEDCincinnati Lamb 16−MC−04026 Page 12−7ALARM NUMBER ALARM DESCRIPTIONA017.5 1175 A17.5 LOAD STN COMMISSION FAILA017.6A017.7A018.0A018.1A018.2A018.3A018.4A018.5A018.6A018.7A019.0 1190 A19.0 X AXIS PMC MOVE CMD FAILA019.1 1191 A19.1 Y AXIS PMC MOVE CMD FAILA019.2 1192 A19.2 Z AXIS PMC MOVE CMD FAILA019.3 1193 A19.3 PMC AXIS MOVE INTERRUPTEDA019.4 1194 A19.4 B/A AXIS PMC MOVE CMD FAILA019.5 2295 A19.5 PATH1 PMC CMD ACTIVEA019.6A019.7A020.0A020.1A020.2 1202A020.3A020.4A020.5A020.6A020.7A021.0 1210 A21.0 SPINDLE M CODE 2 FAILA021.1 1211 A21.1 S CODE GREATER THAN MAXA021.2 1212 A21.2 SPINDLE M CODE 1 FAILA021.3 1213 A21.3 SPINDLE STOP PB, IN CYCLEA021.4 2314 A21.4 SPDL STOP PB,RESTART SPDLA021.5 2315 A21.5 SPDL FAN CB OFFA021.6A021.7A022.0 1220 A22.0 SPDL COMMAND AND NOT VALID GEAR A022.1 1221 A22.1 SPDL CMD AND NOT VALID SP STATEA022.2 1222 A22.2 SPDL NOT ZERO SPEED AT POWER ONA022.3 1223 A22.3 SPDL NOT IN VALID GEAR AT PWR ON A022.4 1224 A22.4 SPINDLE STOPPING TIMEOUT FAILA022.5 1225 A22.5 SPINDLE ORIENTING TIMEOUT FAILA022.6A022.7 1227 A22.7 SPDL CONTACTOR ON TIMEOUT FAILA023.0 1230 A23.0 SPINDLE UP TO SPEED TIMEOUT FAILA023.1 1231 A23.1 SPINDLE DECELERATE TIMEOUT FAIL A023.2 1232 A23.2 GEAR SHIFT ATTEMPTS MORE THAN 5 A023.3 1233 A23.3 SPDL SHIFT TO NEUTRAL FAILEDPage 12−8 Cincinnati Lamb 16−MC−04026ALARM NUMBER ALARM DESCRIPTIONA023.4 1234 A23.4 SPINDLE REORIENTING FAILDA023.5 1235 A23.5 SPDL RUN’G & GEARBOX SW FAILEDA023.6 2336 A23.6 SPDL NOT STOP/RUN/NEUTRALA023.7 2337 A23.7 SPDL NOT IN ANY GEARA024.0 1240 A24.0 SPINDLE STOP TIMEOUTA024.1A024.2 1242 A24.2 SPINDLE START TIMEOUTA024.3 1243 A24.3 SPINDLE ORIENT TIMEOUTA024.4 1244 A24.4 SPINDLE REORIENT TIMEOUTA024.5 1245 A24.5 SPINDLE ACC/DEC TIMEOUTA024.6A024.7A025.0A025.1A025.2A025.3A025.4A025.5A025.6A025.7A026.0 2360 A26.0 SPDL STOP/RUN−CYC INHA026.1 1261 A26.1 SPDL MOTOR ALARM, FANUCA026.2 1262 A26.2 SP MOTOR WINDING SHFT FAILA026.3 1263 A26.3 SPDL ENABLE CONTACTOR ON FAILA026.4 1264 A26.4 SPDL ENABLE CONTACTOR OFF FAIL A026.5 1265 A26.5 RIGID TAPPING & SPDL MCODE FAIL A026.6A026.7A027.0A027.1 2371 A27.1 COOLANT FILTER CLOGGEDA027.2 2372 A27.2 MIST COLLECT MTR OVLDA027.3 1273 A27.3 CLNT LEVEL LOW WHILE STARTINGA027.4 2374 A27.4 COOLANT LEVEL LOWA027.5 2375A27.5 COOLANT TRANSFER FLOW FAILA027.6A027.7A028.0 2380 A28.0 LOW PRESS CLNT OVLDA028.1 1281 A28.1 HI PRESS/LOW PRESS CLNT MTR OVLDA028.2 1282 A28.2 HI PRESS CLNT FLOW FAILA028.3 1283 A28.3 HI PRESS COOL FLOW UNACTUATE FAIL A028.4 1284 A28.4 CHIP WASH MTR OVLDA028.5 1285 A28.5 PART WASH MTR OVLDA028.6A028.7 1287 A28.7 CLNT TRANS PUMP MTR OLDA029.0A029.1A029.2Cincinnati Lamb 16−MC−04026 Page 12−9ALARM NUMBER ALARM DESCRIPTIONA029.3A029.4A029.5A029.6A029.7A030.0A030.1A030.2A030.3A030.4A030.5A030.6A030.7A031.0A031.1A031.2A031.3A031.4A031.5A031.6A031.7A032.0 1320 A32.0 DRAWBAR AUTO COMMAND FAILA032.1 1321 A32.1 DRAWBAR CLAMP TIMEOUTA032.2 1322 A32.2 DRAWBAR UNCLAMP TIMEOUTA032.3 1323 A32.3 DRAWBAR FDBK SW FAILA032.4 1324 A32.4 DRBAR ACTUAT NOT RETR SPDL RUNA032.5 1325 A32.5 AUTO TOOLCHG DB CLAMPING FAILA032.6 2426 A32.6 DRAWBAR POSITION UNKNOWN CYC INH A032.7 2427 A32.7 DRBAR ACTUAT NOT ADV DB UNCLA033.0A033.1A033.2A033.3A033.4A033.5A033.6A033.7A034.0 2440 A34.0 SPDL LUBE PS NOT ONA034.1 2441 A34.1 SPDL LUBE PS NOT OFFA034.2A034.3A034.4A034.5A034.6 1346 A34.6 SPINDLE LUBE LEVEL LOWA034.7 1347 A34.7 SPDL LUBE PUMP MTR OVLDA035.0 2450 A35.0 DBAR SENS1 OVERRANGEA035.1 2451 A35.1 DBAR SENS1 OPEN CURCUITPage 12−10 Cincinnati Lamb 16−MC−04026ALARM NUMBER ALARM DESCRIPTIONA035.2 2452A35.2 DBAR SENS1 READING INVALIDA035.3 2453 A35.3 BDAR SENS1 CONFIG INVALIDA035.4 2454 A35.4 DBAR SENS1 DEFECTIV TERMA035.5 2455 A35.5 DBAR SENS1 UNDERRANGEA035.6 2456 A35.6 DBAR SENS2 OVERRANGEA035.7 2457 A35.7 DBAR SENS2 OPEN CURCUITA036.0 2460A36.0 DBAR SENS2 READING INVALID A036.1 2461 A36.1 DBAR SENS2 CONFIG INVALIDA036.2 2462 A36.2 DBAR SENS2 DEFECTIV TERMA036.3 2463 A36.3 DBAR SENS2 UNDERRANGEA036.4 1364A36.4 NO DRAWBAR SENSOR SELECTED A036.5A036.6A036.7A037.0A037.1A037.2A037.3A037.4A037.5A037.6A037.7A038.0 2480 A38.0 TOOL EJECT RET TIMEOUTA038.1 2481 A38.1 TOOL EJECT ADV TIMEOUTA038.2 2482 A38.2 TOOL EJECT NOT RETRACTEDA038.3A038.4A038.5A038.6A038.7A039.0 5390 A39.0 AUTO CHAIN POSITIONING FAIL A039.1 2491 A39.1 CHAIN DOOR NOT CLSD/LOCKA039.2 2492 A39.2 TOOL CHAIN MANUAL ACCESSA039.3 5393 A39.3 CH DOOR /LOCK BEFOR JOGA039.4 5394 A39.4 TLCHAIN SEQUENCE TIMEOUTA039.5 5395 A39.5 TOOLCHAIN MOVE INTERRUPTEDA039.6 5396 A39.6 CHAIN MOVE & DR/LCK OR EJT/RETA039.7 5397 A39.7 CHAIN INTERFERENCE W/TOOL TRANSPORT A040.0 2500 A40.0 TRANSP TOOL GRIP TIMEA040.1 2501 A40.1 TRANSP TOOL UNGRIP TIMEA040.2 2502 A40.2 TRANSP TO CHAIN TIMEA040.3 2503 A40.3 TRANSP FROM CHIAN TIMEA040.4 2504 A40.4 TRANSP TO DRUM TIMEA040.5 2505 A40.5 TRANSP FROM DRUM TIMEA040.6 2506 A40.6 TRANSP INSERT TIMEA040.7 2507 A40.7 TRANSP REMOVE TIMEA041.0 2510 A41.0 QUEUE CW TIMEOUTCincinnati Lamb 16−MC−04026 Page 12−11ALARM NUMBER ALARM DESCRIPTIONA041.1 2511 A41.1 QUEUE CCW TIMEOUTA041.2 2512 A41.2 QUEUE TOOL TO 0 TIMEOUTA041.3 2513 A41.3 QUEUE TOOL TO 90 TIMEOUTA041.4 2514 A41.4 TOOL QUEUE COMMAND 1 FAILA041.5 2515 A41.5 TOOL QUEUE COMMAND 2 FAILA041.6 2516 A41.6 TOOL QUEUE−CYC INHA041.7A042.0 2520 A42.0 INTERCHANGE ARM NOT CLEARA042.1 5421 A42.1 INTERCHG DOOR CLOSE TIMEOUTA042.2 5422 A42.2 INTERCHG DOOR OPN TIMEOUTA042.3 2523 A42.3 INTERCHG DOOR NOT CLOSEDA042.4 5424 A42.4 INTERCHG TOOLS COMMAND FAILA042.5 5425 A42.5 INTERCHG ARM MOVE INTERRUPTEDA042.6A042.7A043.1A043.2A043.3A043.4A043.5A043.6A043.7A044.0 1440 A44.0 M37 AND NO T CODE FAILA044.1 1441 A44.1 M37 AND INVALID T CODE FAILA044.2 1442 A44.2 M37 AND 200 TOOLS IN QUEUE LISTA044.3A044.4A044.5A044.6A044.7A045.0 1450 A45.0 T CODE ZERO AND NO M06A045.1 1451 A45.1 M06 ONLY AND T NOT PREV PROGA045.2 1452 A45.2 M06 AND DB CLP AND (SP TOOL = 0)A045.3 1453 A45.3 M06 & TL @5B@I430,D2304@5D@ EXPECTED IN SPDL A045.4 1454 A45.4 CHAIN POCK > 40,80,OR 120A045.5 2555A45.5 TOOL MGMT TL CONVERT FAILA045.6 1456 A45.6 INTERCHG TOOL DRAWBAR CLAMP FAILA045.7 1457 A45.7 UNLOAD TOOL DRAWBAR NOTOOL FAILA046.0 1460 A46.0 HANDY OP PANEL DISCONNECTEDA046.1 1461 A46.1 HANDY OP PANEL COMM ERRORA046.2 1462 A46.2 HANDY PANEL LCD ERROR @5B@I110,R2720@5D@ A046.3A046.4A046.5A046.6Page 12−12 Cincinnati Lamb 16−MC−04026ALARM NUMBER ALARM DESCRIPTIONA047.0 1470 A47.0 PALLET CLAMPING FAILA047.1 1471 A47.1 PALLET UNCLAMPING FAILA047.2 1472 A47.2 PALLET CLAMPED PRESSURE FAILUREA047.3 1473 A47.3 PALLET CHANGER RAISE FAILA047.4 1474 A47.4 PALLET CHANGER LOWER FAILA047.5 1475 A47.5 PALLET CLAMP CONES AIRBLAST FAILA047.6 1476 A47.6 PALLET SEAT CHECK IN CYCLE FAILA047.7 2577 A47.7 PALLET NOT SEATEDA048.0 1480 A48.0 PALLET DOOR LOCKING FAILA048.1 2581 A48.1 SHUTTLE PENDING− PRESS PALLET RES ET A048.2 1482 A48.2 PALLET SEAT CHECK AFTER CLAMP FAIL A048.3 1483 A48.3 PALLET DOOR UNLOCK FAILA048.4 1484 A48.4 PLT CHGR INVALID POSN FOR M02A048.5 2585 A48.5 PLT CHGR IN INVALID POSA048.6 5486 A48.6 B2 AXIS PMC MOVE COMMAND FAILA048.7 1487 A48.7 Z AXIS INTERFERS W/PALLETNOT LOWERED OR IN POSITIONA049.0 5490 A49.0 OPER DR INTERFERE W/PALLET CHGRA049.1 2591 A49.1 PALLET DOOR OPEN WHILE MOVINGA049.2 2592 A49.2 PAL IN POS AT LOAD NOT ONA049.3 2593 A49.3 PALLET DOOR NOT CLSDA049.4 2594 A49.4 OPERATOR DOOR NOT CLSDA049.5A049.6A049.7A050.0A050.1A050.2 1502 A50.2 INCH/METRIC MODE CHG FAILA050.4 1504 A50.4 MAIN XFORMER OVERTEMPA050.5 1505 A50.5 POWER PANEL OVERTEMPA050.6A050.7 1507 A50.7 EMERG STOP − HANDY PANELA051.0 2610 A51.0 SPINDLE LUBE AIR PRESS SW FAILA051.1 2611 A51.1 SPINDLE PROTECTION AIR SW FAILA051.2 1512 A51.2 SPINLDE CHILLER FAULTA051.3 2613 A51.3 SPINDLE PRELUBE REQUIREDA051.4 1514 A51.4 SPDL WARMUP TOOL MUST BE TOOL 1A051.5 2615 A51.5 SPINDLE PRELUBE OCCURRINGA051.6 2616 A51.6 SPINDLE WARMUP REQUIREDA051.7 2617 A51.7 SPINDLE WARMUP OCCURINGA052.0 2620 A52.0 TRANSPORT TOOL CMD1 FAILA052.1 2621 A52.1 TRANSPORT TOOL CMD2 FAILA052.2 2622 A52.2 TRANSPORT TOOL CMD3 FAILA052.3 2623 A52.3 TRANSPORT TOOL CMD4 FAILA052.4 2624 A52.4 TOOL TRANSPORT−CYC INHA052.5 1525 A52.5 NO TOOL PRESENT AT CHAIN, CAN’T LOAD TO DRUMCincinnati Lamb 16−MC−04026 Page 12−13ALARM NUMBER ALARM DESCRIPTIONA052.6 1526 A52.6 TOOL IS PRESENT AT CHAIN,CAN’T LOAD FROM DRUMA052.7A053.0 2630 A53.0 SET TOOL 0,DBAR MUST BE UNCL OR NO TOOLA053.1 2631 A53.1 SET TOOL 0 COMPLETE VERIFYTOOL QUEUE IS EMPTYA053.2A053.3 2633 A53.3 SPINDLE − UNKNOWN TOOLA053.4 2634 A53.4 TRANSPORT−UNKNOWN TOOLA053.5 2635 A53.5 QUEUE POCK1−UNKNOWN TOOLA053.6 2636 A53.6 QUEUE POCK2−UNKNOWN TOOLA053.7 2637 A53.7 INTERCHANGE ARM−UNKNOWN TOOLA054.0 2640 A54.0 DRAWBAR NOT ALIGNEDA054.1 2641 A54.1 BACKGND TOOL LOAD/UNL NOT ALIGNED A054.2 2642 A54.2 PALLET CHANGER NOT ALIGNDA054.3 2643 A54.3 ALIGN AND OPERATOR DOOR OPENA054.4 2644 A54.4 ALIGN AND REAR DOOR OPENA054.5 2645 A54.5 ALIGN AND CHAIN DOOR OPENA054.6 2646 A54.6 ALIGN AND ACCESS DOOR OPENA054.7 2647 A54.7 ALIGN AND PALLET DOOR OPENA055.0 1550 PROFIBUS SLAVE 03 COMM FAILA055.1 1551 PROFIBUS SLAVE 04 COMM FAILbus slave 总线受控A055.2 1552 PROFIBUS SLAVE 05 COMM FAILA055.3 1553 PROFIBUS SLAVE 06 COMM FAILA055.4 1554 PROFIBUS SLAVE 07 COMM FAILA055.5 1555 PROFIBUS SLAVE 08 COMM FAILA055.6 1556 PROFIBUS SLAVE 09 COMM FAILA055.7 1557 PROFIBUS SLAVE 10 COMM FAILA056.0A056.1 1561 PROFIBUS SLAVE 12 COMM FAILA056.2 1562 PROFIBUS SLAVE 13 COMM FAILA056.3 1563 PROFIBUS SLAVE 14 COMM FAILA056.4 1564 PROFIBUS SLAVE 15 COMM FAILA056.5 1565 PROFIBUS SLAVE 16 COMM FAILA056.6A056.7A057.0A057.1A057.2A057.3A057.4A057.5A057.6A057.7A058.0 1580PROFIBUS SLAVE 03 NOT READY FAIL A058.1 1581PROFIBUS SLAVE 04 NOT READY FAIL A058.2 1582PROFIBUS SLAVE 05 NOT READY FAIL Page 12−14 Cincinnati Lamb 16−MC−04026ALARM NUMBER ALARM DESCRIPTIONA058.3 1583PROFIBUS SLAVE 06 NOT READY FAIL A058.4 1584PROFIBUS SLAVE 07 NOT READY FAIL A058.5 1585PROFIBUS SLAVE 08 NOT READY FAIL A058.6 1586PROFIBUS SLAVE 09 NOT READY FAIL A058.7 1587PROFIBUS SLAVE 10 NOT READY FAIL A059.0A059.1 1591PROFIBUS SLAVE 12 NOT READY FAIL A059.2 1592PROFIBUS SLAVE 13 NOT READY FAIL A059.3 1593PROFIBUS SLAVE 14 NOT READY FAIL A059.4 1594PROFIBUS SLAVE 15 NOT READY FAIL A059.5 1595PROFIBUS SLAVE 16 NOT READY FAIL A059.6A059.7A060.0A060.1A060.2A060.3A060.4A060.5A060.6A060.7A061.0 2710 A61.0 SPDL RTD 1 OVERRANGEA061.1 2711 A61.1 SPDL RTD 1 OPEN/SHORT CIRCUIT A061.2 2712A61.1 SPDL RTD 1 READING INVALIDA061.3 2713 A61.3 SPDL RTD 1 CONFIG INVALIDA061.4 2714 A61.4 SPDL RTD 1 DEFECTIVE TERMINAL A061.5 2715 A61.5 SPDL RTD 1 UNDERRANGEA061.6 2716 A61.6 SPDL RTD 1 TEMP WARNINGA061.7 2717 A61.7 SPDL RTD 1 TEMP SHUTDOWNA062.0 2720 A62.0 SPDL RTD 2 OVERRANGEA062.1 2721 A62.1 SPDL RTD 2 OPEN/SHORT CIRCUIT A062.2 2722A62.2 SPDL RTD 2 READING INVALIDA062.3 2723 A62.3 SPDL RTD 2 CONFIG INVALIDA062.4 2724 A62.4 SPDL RTD 2 DEFECTIVE TERMINAL A062.5 2725 A62.5 SPDL RTD 2 UNDERRANGEA062.6 2726 A62.6 SPDL RTD 2 TEMP WARNINGA062.7 2726 A62.7 SPDL RTD 2 TEMP SHUTDOWNA063.0 2730 A63.0 SPDL RTD 3 OVERRANGEA063.1 2731 A63.1 SPDL RTD 3 OPEN/SHORT CIRCUIT A063.2 2732A63.2 SPDL RTD 3 READING INVALIDA063.3 2733 A63.3 SPDL RTD 3 CONFIG INVALIDA063.4 2734 A63.4 SPDL RTD 3 DEFECTIVE TERMINAL A063.5 2735 A63.5 SPDL RTD 3 UNDERRANGEA063.6 2736 A63.6 SPDL RTD 3 TEMP WARNINGA063.7 2737 A63.7 SPDL RTD 3 TEMP SHUTDOWNA064.0 2740 A64.0 SPDL RTD 4 OVERRANGEA064.1 2741 A64.1 SPDL RTD 4 OPEN/SHORT CIRCUITCincinnati Lamb 16−MC−04026 Page 12−15ALARM NUMBER ALARM DESCRIPTIONA064.2 2742A64.2 SPDL RTD 4 READING INVALIDA064.3 2743 A64.3 SPDL RTD 4 CONFIG INVALIDA064.4 2744 A64.4 SPDL RTD 4 DEFECTIVE TERMINAL A064.5 2745 A64.5 SPDL RTD 4 UNDERRANGEA064.6 2746 A64.6 SPDL RTD 4 TEMP WARNINGA064.7 2747 A64.7 SPDL RTD 4 TEMP SHUTDOWNA065.0 2750 A65.0 TOOL MGNT NPT CONVERT T CODEA065.1 2751A65.1 TOOL MGMT NOT UPDATE VARBSA065.2A065.3A065.4A065.5A065.6A065.7A066.0 2760A66.0 BACKGND LOAD TL # INVALIDA066.1A066.2A066.3A066.4A066.5A066.6A066.7A067.0 2170A67.0 CHIP CONV STOPPED − AUTO SELA067.1 2171A67.1 CHIP CONV STOPPED − OFF PBA067.2A067.3A067.4A067.5A067.6A067.7A068.0 1680 A68.0 SPDL PRB ERROR−CHECK PROBE UNIT A068.1 1681 A68.1 SPINDLE PROBE BATTERY POWER LOW A068.2 1682 A68.2 PRB SEAT LOST DURING RAPID MOVE A068.3 1683 A68.3 SPINDLE PROBE UNEXPECTED TRIGGER A068.4 1684 A68.4 SPDL PRB OFF BEFORE CHNG’G TOOLSA068.5 1685 A68.5 SPINDLE PROBE MAX SPEED EXCEEDEDA068.6 1686 A68.6 SPINDLE PROBE ON FAILED RETRYA068.7 2787A68.7 SPINDLE PROBE IS ACTIVEA069.0A069.1A069.2A069.3A069.4A069.5A069.6A069.7A070.0 2800 FEEDRATE OVERRIDE SET TO ZEROPage 12−16 Cincinnati Lamb 16−MC−04026ALARM NUMBER ALARM DESCRIPTIONA070.1 2801 OPER HANDHELD PENDANT ACTIVEA070.2 2802 HOP ENABLE FAILED−REQUIRESFDRATE OVERRIDES SET THE SAMEA070.3 2803 RAPID OVERRIDE ENABLEDA070.4A070.5A070.6A070.7 2807SPINDLE STOP REQUIRED−PB INHIB ITA071.0 2810 PALLET UNCLAMPED REQUIREDA071.1 2811 PALLET CHANGER IN POS REQ (0,180) PB INHIBIT A071.2 2812 MOTION INHIBIT − ALARM ACTIVEA071.3 2813 PALLET IN POSN AT LOAD REQUIREDA071.4 2814 PALLET IN UP POSITION REQ − PB INHIBITA071.5 2815 Z AXIS IN PALLET POSITION REQ − PB INHIBITA071.6 2816 PALLET IN DOWN POSITION REQ − PB INHIBITA071.7 2817 MACHINE ON REQUIREDA072.0 2820 MECH MANUAL MODE REQUIREDA072.1 2821 CYCLE ACTIVE − PB INHIBITA072.2 2822 SPINDLE NOT IN VALID GEAR − PB INHIBITA072.3 2823 RIGID TAPPING ACTIVE − PB INHIBITA072.4 2824 DRAWBAR NOT CLAMPED − PB INHIBITA072.5 2825 PALLET SWAP NOT IN VALID POS − PB INHIBITA072.6 2826 SPINDLE SPEED CODE=0 − PB INHIBITA072.7 2827 OPERATOR DOOR OPEN REQUIRED − PB INHIBITA073.0 2830 OPER DOOR CLOSED REQUIRED − PB INHIBITA073.1 2831 REAR DOOR CLOSED REQUIRED − PB INHIBITA073.2 2832 CHAIN DOOR CLOSED REQUIRED − PB INHIBITA073.3 2833 TC ACCESS DOOR CLOSED REQ − PB INHIBITA073.4 2834 PALLET DOOR CLOSED REQUIRED − PB INHIBITA073.5 2835 I−ARM CLEAR OF MACHINE REQ − PB INHIBITA073.6 2836 PALLET CHANGE SEQ ACTIVE − PB INHIBITA073.7 2837 B−AXIS UNCLAMPED REQUIRED − PB INHIBITA074.0 2840 QUEUE ARM AT ZERO POSN REQ − PB INHIBITA074.1 2841 QUEUE DRUM IN POSN REQ − PB INHIBITA074.2 2842 TRANSPORT C LEAR OF DRUM REQ − PB INHIBITA074.3 2843 FEEDHOLD ACTIVE−FRONT FEEDHOLD PB PRESSEDA074.4 2844 TRANSPORT CLEAR OF CHAIN REQ − PB INHIBITA074.5 2845 CHAIN ACCESS REQUESTEDA074.6 2846 CHAIN ACCESS MANUAL ENABLEA074.7 2874 INTERCHANGE DOOR OPEN REQ − PB I NHIBITA075.0 2850 BLOCK DEL− SKIP BLOCKS THAT BEGIN WITH /A075.1 2851 OPT STOP ACT − WAITING FOR M01 TO STOP EXECUTION A075.2 2852 PROG STOP ACTIVE, M00 ACTIVE IN PROGRAMA075.3 2853 PROGRAM TEST FUNCTION ACTIVEALL CUTTING AXES ARE INHIBITEDA075.4 2854 X AXIS INHIBIT ACTIVEA075.5 2855 Y AXIS INHIBIT ACTIVECincinnati Lamb 16−MC−04026 Page 12−17ALARM NUMBER ALARM DESCRIPTIONA075.6 2856 Z AXIS INHIBIT ACTIVEA075.7 2857 A AXIS INHIBIT ACTIVEA076.0 2860 B AXIS INHIBIT ACTIVEA076.1 2861 MACHINE LOCK− S ELECT AXIS PBA076.2 2862 DRY RUN MODE SELECTED − PROGRAMWILL RUN AT JOG FEEDRATEA076.3 2863 SPINDLE PROBE ACTIVE − PB INHIBITA076.4 2864 B AXIS IN POSITION REQUIRED − PB INHIBIT@0A@A076.5 2865 Z AXIS IN FIXED PROBE CLEAR POS’N REQUIRED− PB INHIBITA076.6 2866A076.7 2867A077.0 2870 TRANSPORT ARM IN TOOL INSERT POS REQ − PB INHIBIT A077.1 2871 TRANSPORT ARM AT CHAIN/DRUM POS REQ − PB INHIBIT A077.2 2872 TRANSPORT ARM GRIPPER RELEASED REQ − PB INHIBIT A077.3 2873TRANSPORT ARM FROM DRUM POS REQ − PB INH IBITA077.4 2874 TRANSPORT ARM GRIPPED REQ’D − PB INHIBITA077.5 2875 QUEUE POCKET AT 90 DEG POSITION REQ’D − PB INHIBIT A077.6 2876 NO TOOL PRESENT IN CHAIN REQ − PB INHIBITA077.7 2877 TRANSPORT AT CHIAN POS REQ’D − PB INHIBITA078.0 2880 CHAIN IN VAILID POSITION REQ’D PB INHIBITA078.1 2881A078.2 2882 INVALID POSITION TO START SELECTED MOTIONA078.3 2883A078.4 2884A078.5 2885。
数控机床报警大全
附录1：SINUMERIK 840D系统报警清单1“Battery alarm power supply”电池报警原因：电池电压低于规定值。
纠正措施：更换电池后用应答键消除报警。
（注意：系统必须带电更换电池。
）3“PLC stop”PLC停机原因：PLC没有准备。
纠正措施：用编程器PG读出中断原因（从ISTACK）并进行分析；分析NC屏幕上的PLC 报警。
4“Invalid unit system”非法的单位系统说明：在机床数据MD5002中选择了非法的单位组合，即测量系统的单位（位置控制分辨率）与输人系统的单位（转换系数大于10)之间的组合。
纠正措施：修改机床数据位MD5002，然后关掉电源重开。
5“Too many input buffer parameter”太多的输人缓冲参数说明：当使用“FORMAT USER M.”软键格式化用户程序存储器时扫描这个报警。
纠正措施：修改机床数据MD5（输入低一点的数值），然后重新格式化程序存储器。
7“EPROM check error”EPROM检查错误说明：校对“检查和”发现一个错误。
纠正措施：关掉电源重开，屏幕显示出有缺陷的EPROM，换之。
8“Wrong assignment for axis/spindle"进给轴／主轴分配错误原因：机床数据MD200*或者MD400*或者MD461*设定错误。
纠正措施：检查修改机床数据MD200*、MD400*、MD461*。
9“Too small for UMS”UMS太小说明：系统启动后，UMS的内容被检查，然后准备一个地址清单。
这个地址清单需要一定量的内存空间，UMS清单太大。
10“UMS error”UMS错误原因：机床数据MD5015位6被设置，但没有插人UMS，、UMS不能装载，也就是说是空的。
纠正措施：插人UMS，装载UMS（RAM）。
11“Wrong UMS identifier”UMS标识符错误。
机床报警,中英文互译
T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z 轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL（X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD （刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警)MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR MAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALARM(气压低报警)MOTOR OVERLOAD(电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERRORDOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误) SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCK TRY TO RUN SPINDLE WHILE TAIL NOT LOCK SPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭)关注我们的微信公众号shukongzhpngguo，获取更多数控技术文章。
机床按键与报警显示中英对照
法拉克：ALTER 修改程序及代码INSRT 插入程序DELET 删除程序EOB 完成一句 (END OF BLOCK)CAN 取消(EDIT 或 MDI MODE 情况下使用) INPUT 输入程序及代码OUTPUT START 输出程序及指令OFFSET 储存刀具长度、半径补当值AUX GRAPH 显示图形PRGRM 显示程序内容ALARM 显示发生警报内容或代码POS 显示坐标DGONS PARAM 显示自我诊断及参数功能RESET 返回停止CURSOR 光标上下移动PAGE 上下翻页数控机床中英文对照表ABS和REL——在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标ALL——全选，程序编辑时用PRGRM——程序（program）的缩写，用于查看程序NEXT——查看程序和查看参数时，下一页OPRT——在法那克系统中，选择编辑程序时，也就是按下PRGRM后，再按这个键，才能输入程序号HOST，CONECT——这两个是在系统与外界通信时用的，我没试过，不知道什么作用HELP——查看帮助信息SHIFT——换档键，有些键有两个字符，按下这个键，用来输入顶部那个字符ALTER——程序修改键，编辑程序时用INSERT——程序插入键，编辑程序时用EOB——程序结束符，在编辑程序时，没段程序结束时，要加这个符号CAN——取消键，用来取消输入INPUT——输入键，用来输入程序或参数POS——按此键显示当前机床位置画面PROS——按此键显示当前程序画面OFFSET——按此键显示刀具偏置画面SETTING——按此键显示刀具偏置设定画面SYSTEM——按此键显示系统信息及系统状态画面GRAPH——按此键显示加工时刀具轨迹的图形画面CUSTOM——按此键显示用户宏程序画面手动数据输入 (MDI)直接数字控制方法 (DNC)控制器单元或机控制器单元（MCU常见机床报警信息中英文对照T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL（X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD （刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警)MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR MAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALARM(气压低报警)MOTOR OVERLOAD(电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERRORDOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误) SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCKTRY TO RUN SPINDLE WHILE TAIL NOT LOCKSPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭) SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ONHYDRAULIC MOTOR QF7 OFF（液压马达QF7关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED（液压过滤器阻止）HYDRAULIC OIL LEVEL LOW（液压油位低）HYDRAULIC FAN QF8 OFF（液压风扇QF8关闭）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF（冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK（内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF（内冷却液QF13关闭）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW（低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW（润滑油低）DOOR OPEN（门打开）FRONT DOOR(R) OPEN（前门打开）LEFT DOOR OPEN（左门打开）LUBRICATION OIL QF23 OFF（润滑油QF23关闭）LUBRICATION PRESS LOW（润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED（门没有全部关闭）IN M06,MAG NOT READY（在M06，刀库未准备好）MAGAZINE NOT READY（刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZNOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG 关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG 机床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTERY VOLTAGE IS LOW 探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE（参数写使能）PMC EDIT ENABLE（PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION 主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR 因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC 电池SIEMENS常用缩略语A Output 输出ASCII American Standard Code for Information Interchange 美国信息交换标准代码AV Preparation for work 运行准备BA Operating mode 运行方式BAG Operating mode groups 运行方式组BB Ready for operation 准备好运行BCD Binary Coded Decimals 二-十进制BHG Hand-held terminal 手提终端BOF User interface 用户接口CNC Computerized Numerical Control 计算机化数字控制CP Communication Processor 通迅处理器CPU Central Processing Unit 计算机中央处理装置CR Carriage Return 托架折回CSB Central Service Board(PLC module) 中央维护板，PLC 模块CTS Clear To Send 发送使能DAU Digital-Analog Converter 数模转换器DB Data Block 数据块DIN German Industrial Standards 德国工业标准DIO Data Input/Output 数据输入/输出DRF Differential Resolver Function 差分功能DRY Dry Run 空运行DSB Decoding Single Block 译码单段DSR Data Send Ready 备用输入DW Data Word 数据字E Input 输入EIA-Code Special tape code,number of holes per characters always odd 特殊纸带码，每个字符的孔数为奇数EPROM Programm memory with fixed program 有固定程序的程序存储器E/R Controlled Supply and Energy Recovery Module 可控电源和能量恢复模块ETC ETC key:Extension of the softkey bar in the same menuETC 键：同级菜单扩展键FDB Product designation database 产品指定数据库FIFO First in First Out 先进先出FRA Frame module 帧频模块FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging 坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compensation 铣刀半径补偿FST Feed Stop 停止进给GUD Global User Data 全体用户数据HMS High-Resolution Measuring System 高分辨率测量系统HSA Main Spindle Drive 主轴驱动HW Hardware 硬件IM Interface Module 接口模块IM-S/R Interface Module(S=send/R=receive) 接口模块，S=发送/R=接收INC Increment 步进增量ISO-Code Special tape code,number of holes per character always even特殊纸带码，每个字符的孔数为偶数K1...k4 Channel 1 to Channel 4 通道1 到通道4KOP Ladder Diagram 梯形图KV Loop-Gain Factor 增益系数KUE Transformation Ratio 传动比LCD Liquid Crystal Display 液晶显示LED Light Emitting Diode 发光二极管显示LUD Local User Data 局部用户数据MB Megabyte 兆字节MD Machine Data 机床数据MK Measuring Circuit 测量回路MDA Manual Data Automatic 手动输入，自动执行MLFB Machine-readable product designation 机器可识别的产品代号MMC Man Machine Communication:User interface of the numerical controlsystem for operation,programming and simulation 人机通讯：系统操作界面，用操作，编程和模拟MPF Main Program File：NC part program(main program)NC 零件程序，主程序MPI Multi Point Interface 多点通讯接口MSTT Machine control panel 机床控制面板NC Numerical Control 数字控制NCK Numerical Control Kernel(numerical krnel with block preparation,traversing range etc.) 数字控制核心：具有程序段预处理,运行范围等等NCU Numerical Control Unit 数控单元NURBS Non Uniform Rational B Spline 非均值有理B样条NV Zero Offset 零点偏置OEM Original Equipment Manufacturer 原设备制造商OP Operator Panel 操作面板OPI Operator Panel Interface 操作面板接口PC Personal Comprter 个人计算机PCMCIA Personal Computer Menory Card International Association 接口协议PG Programming Device 编程器PLC Programmable Logic Control 可编程逻辑控制器PRT Program Test 程序测试RAM Random Access Memory 随机存取存储器RISC Reduced Instruction Set Computer 处理器，具有指令组小、通过能力强ROV Rapid Override 快速修调RPA R Parameters Active(NCK memoty area for R parameter numbers)R 参数有效，NCK 中用于R 参数号的存储器区RTS Request To Send(control signal from serial data interfaces)发送请求：来自串行接口的控制信号SBL Single Block 单段SBL2 Single Block Decoding 译码单段SEA Setting Data Active(memory area for setting data in NCK)设定数据有效：用于NCK 中设定数据的存储区SD Setting Data 设定数据SKP Skip Block 程序段跳跃SM Signal Module 信号模块SPF Sub Program File 子程序文件SPS Programmable Logic Controller 可编程逻辑控制器SRK Cutter Radius Compensation 刀尖半径补偿SSFK Leadscrew Error Compensation 丝杠螺距误差补偿SSI Serial Synchronous Interface 串行同步接口SW Software 软件TEA Testing Data Active(with reference to the machine data) 测试数据有效：与机床数据有关TO Tool Offset 刀具补偿TOA Tool Offset Active(memory area for tool offset) 刀具补偿有效，用于刀补的存储区TRANSMIT Transform Milling intoTurning(coordinate conversion onturning machines for milling)铣床转换为车床：车床坐标换算用于铣削加工VSA Feed drive(spindle) 主轴进给驱动V Bit type PLC variable PLC变量类型：位VB Byte type PLC variablePLC变量类型：字节WKZ Tool 刀具WZ Tool 刀具WZK Tool offset 刀具补偿ZOA Zero Offset Active(memory area for zero offsets)零点偏置有效：零点偏置存储区。
数控机床报警大全
附录1：SINUMERIK840D系统报警清单1“Batteryalarmpowersupply”电池报警原因：电池电压低于规定值。
纠正措施：更换电池后用应答键消除报警。
（注意：系统必须带电更换电池。
）3“PLCstop”PLC停机4“5“7“8“Wrongassignmentforaxis/spindle"进给轴／主轴分配错误原因：机床数据MD200*或者MD400*或者MD461*设定错误。
纠正措施：检查修改机床数据MD200*、MD400*、MD461*。
9“ToosmallforUMS”UMS太小说明：系统启动后，UMS的内容被检查，然后准备一个地址清单。
这个地址清单需要一定量的内存空间，UMS清单太大。
原因：机床数据MD5015位6被设置，但没有插人UMS，、UMS不能装载，也就是说是空的。
纠正措施：插人UMS，装载UMS（RAM）。
11“WrongUMSidentifier”UMS标识符错误。
说明：没有装载UMS,是空的；UMS的内容没有定义：①UMS(RAM)被覆盖，②UMS（EPROM）是空的；插入了错误的UMS；当连接WS800时出现错误。
纠正措施：插入正确UMS，重装UMS（RAM）。
121314151617说明：NC系统还没有处理完传输的字符，外部装置又传送来新字符。
纠正措施：检查机床设定数据位5011、5013、5019,5021；测试外部装置；使用线控或者字符控制传输；降低传输波特率。
18“FrameerrorRS232C（V.24）”RS232C口形式错误说明：接口数据或者程序传输时停止位／波特率／数据位设置不正确。
位数，7位数据＋1位奇偶校验位。
19“1/0devicenotreadyRS232C（V.24）”RS232C口1/0装置没有准备原因：从外部设备传来的DSR信号弱。
纠正措施：激活外部设备；不用DSR。
20“PLCalarmmemorynotformatted”PLC报警存储器没有格式化22232426纠正措施：分成两个或者更多的程序块。
机床按键与报警显示中英对照
机床按键与报警显示中英对照法拉克：ALTER 修改程序及代码INSRT 插入程序DELET 删除程序EOB 完成一句 (END OF BLOCK)CAN 取消(EDIT 或 MDI MODE 情况下使用) INPUT 输入程序及代码OUTPUT START 输出程序及指令OFFSET 储存刀具长度、半径补当值AUX GRAPH 显示图形PRGRM 显示程序内容ALARM 显示发生警报内容或代码POS 显示坐标DGONS PARAM 显示自我诊断及参数功能RESET 返回停止CURSOR 光标上下移动PAGE 上下翻页数控机床中英文对照表ABS和REL——在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标ALL——全选，程序编辑时用PRGRM——程序（program）的缩写，用于查看程序NEXT——查看程序和查看参数时，下一页OPRT——在法那克系统中，选择编辑程序时，也就是按下PRGRM后，再按这个键，才能输入程序号HOST，CONECT——这两个是在系统与外界通信时用的，我没试过，不知道什么作用HELP——查看帮助信息SHIFT——换档键，有些键有两个字符，按下这个键，用来输入顶部那个字符ALTER——程序修改键，编辑程序时用INSERT——程序插入键，编辑程序时用EOB——程序结束符，在编辑程序时，没段程序结束时，要加这个符号CAN——取消键，用来取消输入INPUT——输入键，用来输入程序或参数POS——按此键显示当前机床位置画面PROS——按此键显示当前程序画面OFFSET——按此键显示刀具偏置画面SETTING——按此键显示刀具偏置设定画面SYSTEM——按此键显示系统信息及系统状态画面GRAPH——按此键显示加工时刀具轨迹的图形画面CUSTOM——按此键显示用户宏程序画面手动数据输入 (MDI)直接数字控制方法 (DNC)控制器单元或机控制器单元（MCU常见机床报警信息中英文对照T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL（X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD （刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警)MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR MAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALARM(气压低报警)MOTOR OVERLOAD(电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERRORDOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误) SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCKTRY TO RUN SPINDLE WHILE TAIL NOT LOCKSPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭) SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ONHYDRAULIC MOTOR QF7 OFF（液压马达QF7关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED（液压过滤器阻止）HYDRAULIC OIL LEVEL LOW（液压油位低）HYDRAULIC FAN QF8 OFF（液压风扇QF8关闭）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF（冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK（内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF（内冷却液QF13关闭）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW（低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW（润滑油低）DOOR OPEN（门打开）FRONT DOOR(R) OPEN（前门打开）LEFT DOOR OPEN（左门打开）LUBRICATION OIL QF23 OFF（润滑油QF23关闭）LUBRICATION PRESS LOW（润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED（门没有全部关闭）IN M06,MAG NOT READY（在M06，刀库未准备好）MAGAZINE NOT READY（刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZNOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG 关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG 机床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTERY VOLTAGE IS LOW 探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE（参数写使能）PMC EDIT ENABLE（PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION 主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR 因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC 电池SIEMENS常用缩略语A Output 输出ASCII American Standard Code for Information Interchange 美国信息交换标准代码AV Preparation for work 运行准备BA Operating mode 运行方式BAG Operating mode groups 运行方式组BB Ready for operation 准备好运行BCD Binary Coded Decimals 二-十进制BHG Hand-held terminal 手提终端BOF User interface 用户接口CNC Computerized Numerical Control 计算机化数字控制CP Communication Processor 通迅处理器CPU Central Processing Unit 计算机中央处理装置CR Carriage Return 托架折回CSB Central Service Board(PLC module) 中央维护板，PLC 模块CTS Clear To Send 发送使能DAU Digital-Analog Converter 数模转换器DB Data Block 数据块DIN German Industrial Standards 德国工业标准DIO Data Input/Output 数据输入/输出DRF Differential Resolver Function 差分功能DRY Dry Run 空运行DSB Decoding Single Block 译码单段DSR Data Send Ready 备用输入DW Data Word 数据字E Input 输入EIA-Code Special tape code,number of holes per characters always odd 特殊纸带码，每个字符的孔数为奇数EPROM Programm memory with fixed program 有固定程序的程序存储器E/R Controlled Supply and Energy Recovery Module 可控电源和能量恢复模块ETC ETC key:Extension of the softkey bar in the same menuETC 键：同级菜单扩展键FDB Product designation database 产品指定数据库FIFO First in First Out 先进先出FRA Frame module 帧频模块FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging 坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compensation 铣刀半径补偿FST Feed Stop 停止进给GUD Global User Data 全体用户数据HMS High-Resolution Measuring System 高分辨率测量系统HSA Main Spindle Drive 主轴驱动HW Hardware 硬件IM Interface Module 接口模块IM-S/R Interface Module(S=send/R=receive) 接口模块，S=发送/R=接收INC Increment 步进增量ISO-Code Special tape code,number of holes per character always even特殊纸带码，每个字符的孔数为偶数K1...k4 Channel 1 to Channel 4 通道1 到通道4KOP Ladder Diagram 梯形图KV Loop-Gain Factor 增益系数KUE Transformation Ratio 传动比LCD Liquid Crystal Display 液晶显示LED Light Emitting Diode 发光二极管显示LUD Local User Data 局部用户数据MB Megabyte 兆字节MD Machine Data 机床数据MK Measuring Circuit 测量回路MDA Manual Data Automatic 手动输入，自动执行MLFB Machine-readable product designation 机器可识别的产品代号MMC Man Machine Communication:User interface of the numerical controlsystem for operation,programming and simulation 人机通讯：系统操作界面，用操作，编程和模拟MPF Main Program File：NC part program(main program)NC 零件程序，主程序MPI Multi Point Interface 多点通讯接口MSTT Machine control panel 机床控制面板NC Numerical Control 数字控制NCK Numerical Control Kernel(numerical krnel with block preparation,traversing range etc.) 数字控制核心：具有程序段预处理,运行范围等等NCU Numerical Control Unit 数控单元NURBS Non Uniform Rational B Spline 非均值有理B样条NV Zero Offset 零点偏置OEM Original Equipment Manufacturer 原设备制造商OP Operator Panel 操作面板OPI Operator Panel Interface 操作面板接口PC Personal Comprter 个人计算机PCMCIA Personal Computer Menory Card International Association 接口协议PG Programming Device 编程器PLC Programmable Logic Control 可编程逻辑控制器PRT Program Test 程序测试RAM Random Access Memory 随机存取存储器RISC Reduced Instruction Set Computer 处理器，具有指令组小、通过能力强ROV Rapid Override 快速修调RPA R Parameters Active(NCK memoty area for R parameter numbers)R 参数有效，NCK 中用于R 参数号的存储器区RTS Request To Send(control signal from serial data interfaces)发送请求：来自串行接口的控制信号SBL Single Block 单段SBL2 Single Block Decoding 译码单段SEA Setting Data Active(memory area for setting data in NCK)设定数据有效：用于NCK 中设定数据的存储区SD Setting Data 设定数据SKP Skip Block 程序段跳跃SM Signal Module 信号模块SPF Sub Program File 子程序文件SPS Programmable Logic Controller 可编程逻辑控制器SRK Cutter Radius Compensation 刀尖半径补偿SSFK Leadscrew Error Compensation 丝杠螺距误差补偿SSI Serial Synchronous Interface 串行同步接口SW Software 软件TEA Testing Data Active(with reference to the machine data) 测试数据有效：与机床数据有关TO Tool Offset 刀具补偿TOA Tool Offset Active(memory area for tool offset) 刀具补偿有效，用于刀补的存储区TRANSMIT Transform Milling into Turning(coordinate conversion onturning machines for milling)铣床转换为车床：车床坐标换算用于铣削加工VSA Feed drive(spindle) 主轴进给驱动V Bit type PLC variable PLC变量类型：位VB Byte type PLC variablePLC变量类型：字节WKZ Tool 刀具WZ Tool 刀具WZK Tool offset 刀具补偿ZOA Zero Offset Active(memory area for zero offsets) 零点偏置有效：零点偏置存储区。
机床按键与报警显示中英对照
法拉克：ALTER 修改程序与代码INSRT 插入程序DELET 删除程序EOB 完成一句 (END OF BLOCK)CAN 取消(EDIT 或 MDI MODE 情况下使用) INPUT 输入程序与代码OUTPUT START 输出程序与指令OFFSET 储存刀具长度、半径补当值AUX GRAPH 显示图形PRGRM 显示程序内容ALARM 显示发生警报内容或代码POS 显示坐标DGONS PARAM 显示自我诊断与参数功能RESET 返回停止CURSOR 光标上下移动PAGE 上下翻页数控机床中英文对照表ABS和REL——在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标ALL——全选，程序编辑时用PRGRM——程序（program）的缩写，用于查看程序NEXT——查看程序和查看参数时，下一页OPRT——在法那克系统中，选择编辑程序时，也就是按下PRGRM后，再按这个键，才能输入程序号HOST，CONECT——这两个是在系统与外界通信时用的，我没试过，不知道什么作用HELP——查看帮助信息SHIFT——换档键，有些键有两个字符，按下这个键，用来输入顶部那个字符ALTER——程序修改键，编辑程序时用INSERT——程序插入键，编辑程序时用EOB——程序完毕符，在编辑程序时，没段程序完毕时，要加这个符号CAN——取消键，用来取消输入INPUT——输入键，用来输入程序或参数POS——按此键显示当前机床位置画面PROS——按此键显示当前程序画面OFFSET——按此键显示刀具偏置画面SETTING——按此键显示刀具偏置设定画面SYSTEM——按此键显示系统信息与系统状态画面GRAPH——按此键显示加工时刀具轨迹的图形画面CUSTOM——按此键显示用户宏程序画面手动数据输入 (MDI)直接数字控制方法 (DNC)控制器单元或机控制器单元（MCU常见机床报警信息中英文对照T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL（X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD （刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警)MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR MAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALARM(气压低报警)MOTOR OVERLOAD(电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERRORDOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误) SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCK TRY TO RUN SPINDLE WHILE TAIL NOT LOCK SPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭)SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ONHYDRAULIC MOTOR QF7 OFF（液压马达QF7关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED（液压过滤器阻止）HYDRAULIC OIL LEVEL LOW（液压油位低）HYDRAULIC FAN QF8 OFF（液压风扇QF8关闭）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF（冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK（内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF（内冷却液QF13关闭）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW（低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW（润滑油低）DOOR OPEN（门打开）FRONT DOOR(R) OPEN（前门打开）LEFT DOOR OPEN（左门打开）LUBRICATION OIL QF23 OFF（润滑油QF23关闭）LUBRICATION PRESS LOW（润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED（门没有全部关闭）IN M06,MAG NOT READY（在M06，刀库未准备好）MAGAZINE NOT READY（刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZNOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG 关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG 机床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTERY VOLTAGE IS LOW 探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE（参数写使能）PMC EDIT ENABLE（PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION 主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR 因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC 电池SIEMENS常用缩略语A Output 输出ASCII American Standard Code for Information Interchange 美国信息交换标准代码AV Preparation for work 运行准备BA Operating mode 运行方式BAG Operating mode groups 运行方式组BB Ready for operation 准备好运行BCD Binary Coded Decimals 二-十进制BHG Hand-held terminal 手提终端BOF User interface 用户接口CNC Computerized Numerical Control 计算机化数字控制CP Communication Processor 通迅处理器CPU Central Processing Unit 计算机中央处理装置CR Carriage Return 托架折回CSB Central Service Board(PLC module) 中央维护板，PLC 模块CTS Clear To Send 发送使能DAU Digital-Analog Converter 数模转换器DB Data Block 数据块DIN German Industrial Standards 德国工业标准DIO Data Input/Output 数据输入/输出DRF Differential Resolver Function 差分功能DRY Dry Run 空运行DSB Decoding Single Block 译码单段DSR Data Send Ready 备用输入DW Data Word 数据字E Input 输入EIA-Code Special tape code,number of holes per characters always odd 特殊纸带码，每个字符的孔数为奇数EPROM Programm memory with fixed program 有固定程序的程序存储器E/R Controlled Supply and Energy Recovery Module 可控电源和能量恢复模块ETC ETC key:Extension of the softkey bar in the same menuETC 键：同级菜单扩展键FDB Product designation database 产品指定数据库FIFO First in First Out 先进先出FRA Frame module 帧频模块FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging 坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compensation 铣刀半径补偿FST Feed Stop 停止进给GUD Global User Data 全体用户数据HMS High-Resolution Measuring System 高分辨率测量系统HSA Main Spindle Drive 主轴驱动HW Hardware 硬件IM Interface Module 接口模块IM-S/R Interface Module(S=send/R=receive) 接口模块，S=发送/R=接收INC Increment 步进增量ISO-Code Special tape code,number of holes per character always even特殊纸带码，每个字符的孔数为偶数K1...k4 Channel 1 to Channel 4 通道1 到通道4KOP Ladder Diagram 梯形图KV Loop-Gain Factor 增益系数KUE Transformation Ratio 传动比LCD Liquid Crystal Display 液晶显示LED Light Emitting Diode 发光二极管显示LUD Local User Data 局部用户数据MB Megabyte 兆字节MD Machine Data 机床数据MK Measuring Circuit 测量回路MDA Manual Data Automatic 手动输入，自动执行MLFB Machine-readable product designation 机器可识别的产品代号MMC Man Machine Communication:User interface of the numerical controlsystem for operation,programming and simulation 人机通讯：系统操作界面，用操作，编程和模拟MPF Main Program File：NC part program(main program)NC 零件程序，主程序MPI Multi Point Interface 多点通讯接口MSTT Machine control panel 机床控制面板NC Numerical Control 数字控制NCK Numerical Control Kernel(numerical krnel with block preparation,traversing range etc.) 数字控制核心：具有程序段预处理,运行范围等等NCU Numerical Control Unit 数控单元NURBS Non Uniform Rational B Spline 非均值有理B 样条NV Zero Offset 零点偏置OEM Original Equipment Manufacturer 原设备制造商OP Operator Panel 操作面板OPI Operator Panel Interface 操作面板接口PC Personal Comprter 个人计算机PCMCIA Personal Computer Menory Card International Association 接口协议PG Programming Device 编程器PLC Programmable Logic Control 可编程逻辑控制器PRT Program Test 程序测试RAM Random Access Memory 随机存取存储器RISC Reduced Instruction Set Computer 处理器，具有指令组小、通过能力强ROV Rapid Override 快速修调RPA R Parameters Active(NCK memoty area for R parameter numbers)R 参数有效，NCK 中用于R 参数号的存储器区RTS Request To Send(control signal from serial data interfaces)发送请求：来自串行接口的控制信号SBL Single Block 单段SBL2 Single Block Decoding 译码单段SEA Setting Data Active(memory area for setting data in NCK)设定数据有效：用于NCK 中设定数据的存储区SD Setting Data 设定数据SKP Skip Block 程序段跳跃SM Signal Module 信号模块SPF Sub Program File 子程序文件SPS Programmable Logic Controller 可编程逻辑控制器SRK Cutter Radius Compensation 刀尖半径补偿SSFK Leadscrew Error Compensation 丝杠螺距误差补偿SSI Serial Synchronous Interface 串行同步接口SW Software 软件TEA Testing Data Active(with reference to the machine data) 测试数据有效：与机床数据有关TO Tool Offset 刀具补偿TOA Tool Offset Active(memory area for tool offset) 刀具补偿有效，用于刀补的存储区TRANSMIT Transform Milling intoTurning(coordinate conversion onturning machines for milling)铣床转换为车床：车床坐标换算用于铣削加工VSA Feed drive(spindle) 主轴进给驱动V Bit type PLC variable PLC变量类型：位VB Byte type PLC variablePLC变量类型：字节WKZ Tool 刀具WZ Tool 刀具WZK Tool offset 刀具补偿ZOA Zero Offset Active(memory area for zero offsets)零点偏置有效：零点偏置存储区。
机床按键与报警显示中英对照
机床按键与报警显示中英对照法拉克：ALTER修改程序及代码INSRT插入程序DELET删除程序EOB完成一句(END OF BLOCK)CAN取消(EDIT或MDI MODE情况下使用) INPUT输入程序及代码OUTPUT STAR输出程序及指令OFFSET储存刀具长度、半径补当值AUX GRAPH S示图形PRGRM B示程序内容ALARM S示发生警报内容或代码POS显示坐标DGONS PARA显示自我诊断及参数功能RESET返回停止CURSORS标上下移动数控机床中英文对照表ABS和RE 在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标ALL——全选，程序编辑时用PRGR——程序（program）的缩写，用于查看程序NEXT查看程序和查看参数时，下一页OPR——在法那克系统中，选择编辑程序时，也就是按下PRGR后，再按这个键，才能输入程序号HOST CONEC——这两个是在系统与外界通信时用的，我没试过，不知道什么作用HELP查看帮助信息SHIFT——换档键，有些键有两个字符，按下这个键，用来输入顶部那个字符ALTER程序修改键，编辑程序时用INSERT程序插入键，编辑程序时用EOB --- 程序结束符，在编辑程序时，没段程序结束时，要加这个符号CAN取消键，用来取消输入INPUT输入键，用来输入程序或参数POS按此键显示当前机床位置画面PRO——按此键显示当前程序画面OFFSE——按此键显示刀具偏置画面SETTING按此键显示刀具偏置设定画面GRAP——按此键显示加工时刀具轨迹的图形画面CUSTOM—按此键显示用户宏程序画面手动数据输入(MDI)直接数字控制方法(DNC)控制器单元或机控制器单元(MCUT WORD ERROR（ T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP；急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法 T代码） M CODE ERROR （ M代码出错，非法 M代码） SERVO NOT READ（伺服未准备好）NC NOT READY NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流 24 断开）+24V NOT READY（ +24V 没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME轴未回零）PLEASE DRUM RETURN HOM刀库未回零）AIRPRESSFAILURE 气压故障）UNCL TOOL FAL（松刀失败）AIR PRESSURE DROP（压缩空气压力过低）CLAMP TOOL FAL（夹刀失败）DRUM NOT PARKED^库未在原值）X ZERO POINT NOT REACHED（ X 车由未回零）Y ZERO POINT NOT REACHED（ Y 车由未回零）Z ZERO POINT NOT REACHED（ Z 车由未回零）4TH ZERO POINT NOT REACHE（第 4 车由未回零）X AXIS OVERTRAVL（ X 轴超限）Y AXIS OVERTRAVL （Y 轴超限）Z AXIS OVERTRAVL （Z 轴超限）COUNTER SWITCH REEOR计数开关故障）MASTERT RANSFER OVER TEM；主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z 轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK 请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL刀库摆向换刀位失败）MG SWING OVERLOA刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOA刀库移动电机过载）COOLANT MOTOR OVERLOA冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKE D刀具未锁紧）BATTER Y ALARM （电池报警）DRUMPOSITIONSWITCFERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK刀库未在原始位置）IT DANGOU TO MOVE DRU M 刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FAL；I机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED工件未夹紧）AUTO TOOL CHANGE FAULT 自动换刀失败）TOOL DATA OUT OF RANG（指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE 目标刀具在主轴上）THETHREESPINDLESWITCHFAULT （主轴上的接近开关） THE CENTRE COOLANT IS LOWER刀具内冷泵液位过低） DRUMRETURN 1# POSITION FAULT；刀库自动回零失败） SPINDLE OVERLOAD；主轴过载）TURRENT MOTOR OVERLOA刀盘转动电机过载）CHIP CONVE YER OVERLOAD拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED分度头未锁紧）MT NOT READY机床没准备好）MG OVERLOAD刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE气压不足）COOLANT NOT READY冷却没准备好）LUBE EMPTY油雾油位低，润滑油位低）LUB PRESSURE LOV润滑压力低）CONVE Y VERLOAJ排屑过载）LUB OVERLOAD润滑过载）LUBE PRESSURE LOW tt 雾压力低）SERIAL SPINDLE ALARM （串行主轴报警）NC BATTERY LOW ALARM（电也低报警）MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERRORMAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALAR气压低报警）MOTOR OVERLOAD机过载）T CODE > MAGAZINE TOOLSTCODE < 1 ERROR 5TH AXIS HARDWARE OVERTRAVER LIMIT ERROR DOOR IS OPENED开门）LUB PRESSURE SWITCH ERRSPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMA 主轴负荷异常）TRANSDUCER ALAR传感器报警）BED-HEAD LUBRICATE OFF 床头润滑关闭）EMG OFFHY DRAULIC CHUCK PRESS LQV液压夹头压力低）HY DRAULIC TAIL PRESS LO（液压尾座压力低）LUB 0IL LOW （油压低）TURRET CODE ERRQ转塔码错误）TURRET RUN OVERTIME专塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCKTRY TO RUN SPINDLE WHILE TAIL NOT LOCKSPINDLE NEUTRAL GEARMAGAZINE ADJUSTHY DRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,C YCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED （X 轴被锁定）Y AXIS IS LOCKED （Y 轴被锁定）Z AXIS IS LOCKED （Z 轴被锁定）A AXIS IS LOCKED （A 轴被锁定）SPINDLE MOTOR FAN QF26 OF主轴电机风扇 QF26关闭）SPINDLE ORIENTATION INCOMPLETE^ 轴定位不完全）M FUNCTION NOT COMPLETED 功能无法完成）SPINDLE NOT IN GEAR POSITION （齿轮不在主轴位置）SPINDLENOTCHANGEDO LOWGEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRA 主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ONHYDRAULIC MOTOR QF7 OFF 液压马达 QF7关闭）HY DRAULIC TEMPRETURE HIGH 液压使用温度高）HY DRAULIC FILTER BLOCKED液压过滤器阻止）HYDRAULIC OIL LEVEL LOW 液压油位低）HY DRAULIC FAN QF8 OFF 液压风扇 QF8 关闭）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OF冷却液电机 QF12 关闭）COOLNT LEVEL LOW,C YCLE STOP AFTER 20 MINUTES INNER COOLANT BLOCK内冷却堵塞）SPINDLECOOLANMOTOQF14OFF （主轴冷却液电机 QF14 关闭）INNER COOLANT QF13 OFF内冷却液 QF13关闭）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW低氐气压）SPINDLE COOLANT MOTOR FAUL主轴冷却液电机故障）LUB.OIL IS LOW （润滑油低）DOOR OPEN门打开）FRONT DOOR（R） OPEN前0 打开）LEFT DOOR OPEN 左门打开）LUBRICATION OIL QF23 OFF （润滑油 QF23关闭）LUBRICATION PRESS LOW润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T 在调整，刀库不能交换T）NOT ALL DOOR CLOSED门没有全部关闭）IN M06,MAG NOT READY在 M06,刀库未准备好）MAGAZINE NOT READY刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZNOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG .JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定 D499 为 0K PARAM ABOUT MAG SET IS WRONG于 MAG的 K参数设定错误MECHANICAL BRAKE NOT RELEAS机床抱闸没有松开MECHANICAL BRAKE IS WRONG床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTER Y VOLTAGE IS LOW 头电池电压低PROBE IS ERR探头错误PARAMETER WRITE ENABL 参数写使能）PMC EDIT ENABLE（ PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS主轴档位信号消失T_CLAMPED_SIGNAL MISS 夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION 由倍率开关断路FEED OVERRIDE SWITCH DISCONNECT 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO A因为缺少压空交换停止THECOOLANWATEFTOOLOW,ADLCOOLANWATEFAT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WA冷却水液位低PLEASE REPLACE CNC BATTER Y QUICK请立即更换 CNC 电池SIEMENS常用缩略语A Output 输出ASCII America n Stan dard Code for In formatio nIn tercha nge 美国信息交换标准代码AV Preparati on for work 运行准备BA Operati ng mode 运行方式BAG Operati ng mode groups 运行方式组BB Ready for operati on 准备好运行BCD Bin ary Coded Decimals 二-十进制BHG Han d-held termi nal 手提终端BOF User in terface 用户接口CNC Computerized Numerical C on trol 计算机化数字控制CP Communi cati on Processor 通迅处理器CPU Central Process ing Unit 计算机中央处理装置CR Carriage Retur n 托架折回CSB Cen tral Service Board(PLC module) 中央维护板， PLC 模块CTS Clear To Se nd 发送使能DAU Digital-A nalog Con verter 数模转换器DB Data Block 数据块DIN Germa n In dustrial Sta ndards 德国工业标准DRF Differe ntial Resolver Fun cti on差分功能DRY Dry Run空运行DSB Decodi ng Si ngle Block 译码单段DSR Data Send Ready 备用输入DW Data Word 数据字E In put 输入EIA-Code Special tape code ,nu mber of holes per characters always odd 特殊纸带码，每个字符的孔数为奇数EPROM Programm memory with fixed program 有固定程序的程序存储器E/R Con trolled Supply and En ergy Recovery Module 可控电源和能量恢复模块ETCETCkey:Extension of the softkey bar in the same menuETC键：同级菜单扩展键FDB Product desig natio n database 产品指定数据库FIFO First in First Out 先进先出FRA Frame module 帧频模块FRAME Coordin ate conv ersi on with the comp onents zerooffset ， rotation ， scaling ，mirror-imagi ng 坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compe nsati on铣刀半径补偿FST Feed Stop 停止进给GUD Global User Data 全体用户数据HMS High-Resolution Measuri ng System 高分辨率测量系统HSA Main Spi ndle Drive 主轴驱动HW Hardware 硬件IM In terface Module 接口模块IM-S/R In terface Module(S=se nd/R二receive) 接口模块，S二发送/R=接收INC In creme nt 步进增量ISO-Code Special tape code ,nu mber of holes per character always eve n特殊纸带码，每个字符的孔数为偶数K1...k4 Channel 1 to Channel 4 通道 1 到通道 4 KOP Ladder Diagram 梯形图KV Loop-Gain Factor 增益系数KUE Tran sformati on Ratio 传动比LCD Liquid Crystal Display 液晶显示LED Light Emitti ng Diode 发光二极管显示LUD Local User Data 局部用户数据MB Megabyte 兆字节MD Machine Data 机床数据MK Measuri ng Circuit 测量回路MDA Ma nual Data Automatic 手动输入，自动执行MLFB Machi ne-readable product desig natio n 机器可识别的产品代号MMCMa n Mach ine Com mun icatio n:User in terface of thenu merical con trolsystem for operation,programming and simulation 人机通讯：系统操作界面，用操作，编程和模拟MPFMain Program File : NCpart program(main program)NC零件程序，主程序MPI Multi Poi nt In terface 多点通讯接口MSTT Machi ne control pan el 机床控制面板NC Numerical Co ntrol 数字控制NCK Numerical Con trol Kern el( nu merical krnel with block preparati on,traversi ng range etc.) 数字控制核心：具有程序段预处理,运行范围等等NCU Numerical Control Un it 数控单元NURBS Non Uniform Rational B Spline 非均值有理 B 样条NV Zero Offset 零点偏置OEM Origi nal Equipme nt Manu facturer原设备制造商OP Operator Panel 操作面板OPI Operator Panel In terface 操作面板接口PC Perso nal Comprter 个人计算机PCMCIAPersonal Computer Menory Card International Association 接口协议PG Programmi ng Device 编程器PLC Programmable Logic Con trol 可编程逻辑控制器PRT Program Test 程序测试RAM Ra ndom Access Memory随机存取存储器RISC Reduced In structio n Set Computer 处理器，具有指令组小、通过能力强ROV Rapid Override 快速修调RPA R Parameters Active(NCK memoty area for R parameter nu mbers)R参数有效，NCK中用于R参数号的存储器区RTSRequest To Send(control signal from serial data in terfaces)发送请求：来自串行接口的控制信号SBL Si ngle Block 单段SBL2 Si ngle Block Decodi ng 译码单段SEASetting Data Active(memory area for setting data in NCK) 设定数据有效：用于 NCK中设定数据的存储区SD Setti ng Data 设定数据SKP Skip Block 程序段跳跃SM Sig nal Module 信号模块SPF Sub Program File 子程序文件SPS Programmable Logic Con troller 可编程逻辑控制器SRK Cutter Radius Compe nsation 刀尖半径补偿SSFK Leadscrew Error Compe nsation 丝杠螺距误差补偿SSI Serial Sy nchro nous In terface 串行同步接口SW Software 软件TEA Testi ng Data Active(with refere nee to the mach ine data) 测试数据有效：与机床数据有关TO Tool Offset 刀具补偿TOATool Offset Active(memory area for tool offset) 刀具补偿有效，用于刀补的存储区TRANSMITTransform Milling into Turning(coordinate conversion onturning machi nes for milli ng)铣床转换为车床：车床坐标换算用于铣削加工VSA Feed drive(spi ndle) 主轴进给驱动V Bit type PLC variable PLC变量类型：位VB Byte type PLC variablePLC变量类型：字节WKZ Tool 刀具WZ Tool刀具WZK Tool offset 刀具补偿ZOAZero Offset Active(memory area for zero offsets) 零点偏置有效：零点偏置存储区。
数控机床报警大全
数控机床报警大全(总16页) -CAL-FENGHAI.-(YICAI)-Company One1-CAL-本页仅作为文档封面，使用请直接删除附录1：SINUMERIK 840D系统报警清单1“Battery alarm power supply”电池报警原因：电池电压低于规定值。
纠正措施：更换电池后用应答键消除报警。
（注意：系统必须带电更换电池。
）3“PLC stop”PLC停机原因：PLC没有准备。
纠正措施：用编程器PG读出中断原因（从ISTACK）并进行分析；分析NC屏幕上的PLC报警。
4“Invalid unit system”非法的单位系统说明：在机床数据MD5002中选择了非法的单位组合，即测量系统的单位（位置控制分辨率）与输人系统的单位（转换系数大于10)之间的组合。
纠正措施：修改机床数据位MD5002，然后关掉电源重开。
5“Too many input buffer parameter”太多的输人缓冲参数说明：当使用“FORMAT USER M.”软键格式化用户程序存储器时扫描这个报警。
纠正措施：修改机床数据MD5（输入低一点的数值），然后重新格式化程序存储器。
7“EPROM check error”EPROM检查错误说明：校对“检查和”发现一个错误。
纠正措施：关掉电源重开，屏幕显示出有缺陷的EPROM，换之。
8“Wrong assignment for axis/spindle"进给轴／主轴分配错误原因：机床数据MD200*或者MD400*或者MD461*设定错误。
纠正措施：检查修改机床数据MD200*、MD400*、MD461*。
9“Too small for UMS”UMS太小说明：系统启动后，UMS的内容被检查，然后准备一个地址清单。
这个地址清单需要一定量的内存空间，UMS清单太大。
10“UMS error”UMS错误原因：机床数据MD5015位6被设置，但没有插人UMS，、UMS不能装载，也就是说是空的。
2017年数控机床维修常见机床报警中英文对照大全【推荐】
书山有路勤为径，学海无涯苦作舟
2017 年数控机床维修常见机床报警中英文对照大全
【推荐】
为帮助大家了解更多数控机床维修的相关知识，下面，小编为大家分享数控机床维修常见机床报警中英文对照大全，希望对大家有所帮助!
HYDRAULIC MOTOR QF7 OFF( 液压马达QF7 关闭)
HYDRAULIC TEMPRETURE HIGH( 液压使用温度高)
HYDRAULIC FILTER BLOCKED(液压过滤器阻止)
HYDRAULIC OIL LEVEL LOW( 液压油位低)
HYDRAULIC FAN QF8 OFF(液压风扇QF8 关闭)
HELIX CONYER QF9 OR QF10 OFF
CHAIN CONYER QF11 OFF
COOLANT MOTOR QF12 OFF(冷却液电机QF12 关闭)
COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTES
INNER COOLANT BLOCK(内冷却堵塞)
SPINDLE COOLANT MOTOR QF14 OFF(主轴冷却液电机QF14
关闭)
INNER COOLANT QF13 OFF(内冷却液QF13 关闭)
MAG MOTOR QF15 OFF
WORD ERROR (T 码错误)
LOW OIL LEVEL (油位低)
SPINPLE FAULT (主轴故障)
SPINDLE ALARM (主轴报警)
EXTERNAL EMG STOP (急停按钮被按下)。
最全的机床中英文对照
数控机床中英文对照表ABS和REL——在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标ALL——全选，程序编辑时用PRGRM——程序（program）的缩写，用于查看程序NEXT——查看程序和查看参数时，下一页OPRT——在法那克系统中，选择编辑程序时，也就是按下PRGRM后，再按这个键，才能输入程序号HOST，CONECT——这两个是在系统与外界通信时用的，我没试过，不知道什么作用HELP——查看帮助信息SHIFT——换档键，有些键有两个字符，按下这个键，用来输入顶部那个字符ALTER——程序修改键，编辑程序时用INSERT——程序插入键，编辑程序时用EOB——程序结束符，在编辑程序时，没段程序结束时，要加这个符号CAN——取消键，用来取消输入INPUT——输入键，用来输入程序或参数POS——按此键显示当前机床位置画面PROS——按此键显示当前程序画面OFFSET——按此键显示刀具偏置画面SETTING——按此键显示刀具偏置设定画面SYSTEM——按此键显示系统信息及系统状态画面GRAPH——按此键显示加工时刀具轨迹的图形画面CUSTOM——按此键显示用户宏程序画面手动数据输入(MDI)直接数字控制方法(DNC)控制器单元或机控制器单元（MCU）法拉克：ALTER 修改程序及代码INSRT 插入程序DELET 删除程序EOB 完成一句(END OF BLOCK)CAN 取消(EDIT 或MDI MODE 情况下使用)INPUT 输入程序及代码OUTPUT START 输出程序及指令OFFSET 储存刀具长度、半径补当值AUX GRAPH 显示图形PRGRM 显示程序内容ALARM 显示发生警报内容或代码POS 显示坐标DGONS PARAM 显示自我诊断及参数功能RESET 返回停止CURSOR 光标上下移动PAGE 上下翻页常见机床报警信息中英文对照T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z 轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL（X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD （刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警)MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR MAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALARM(气压低报警)MOTOR OVERLOAD(电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERRORDOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误)SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCKTRY TO RUN SPINDLE WHILE TAIL NOT LOCKSPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭) SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ONHYDRAULIC MOTOR QF7 OFF（液压马达QF7关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED（液压过滤器阻止）HYDRAULIC OIL LEVEL LOW（液压油位低）HYDRAULIC FAN QF8 OFF（液压风扇QF8关闭）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF（冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK（内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF（内冷却液QF13关闭）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW（低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW（润滑油低）DOOR OPEN（门打开）FRONT DOOR(R) OPEN（前门打开）LEFT DOOR OPEN（左门打开）LUBRICATION OIL QF23 OFF（润滑油QF23关闭）LUBRICATION PRESS LOW（润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED（门没有全部关闭）IN M06,MAG NOT READY（在M06，刀库未准备好）MAGAZINE NOT READY（刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZ NOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG 关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG 机床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTERY VOLTAGE IS LOW 探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE（参数写使能）PMC EDIT ENABLE（PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION 主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR 因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC电池SIEMENS常用缩略语A Output 输出ASCII American Standard Code for Information Interchange 美国信息交换标准代码AV Preparation for work 运行准备BA Operating mode 运行方式BAG Operating mode groups 运行方式组BB Ready for operation 准备好运行BCD Binary Coded Decimals 二-十进制BHG Hand-held terminal 手提终端BOF User interface 用户接口CNC Computerized Numerical Control 计算机化数字控制CP Communication Processor 通迅处理器CPU Central Processing Unit 计算机中央处理装置CR Carriage Return 托架折回CSB Central Service Board(PLC module) 中央维护板，PLC 模块CTS Clear To Send 发送使能DAU Digital-Analog Converter 数模转换器DB Data Block 数据块DIN German Industrial Standards 德国工业标准DIO Data Input/Output 数据输入/输出DRF Differential Resolver Function 差分功能DRY Dry Run 空运行DSB Decoding Single Block 译码单段DSR Data Send Ready 备用输入DW Data Word 数据字E Input 输入EIA-Code Special tape code,number of holes per characters alwaysodd 特殊纸带码，每个字符的孔数为奇数EPROM Programm memory with fixed program 有固定程序的程序存储器E/R Controlled Supply and Energy Recovery Module 可控电源和能量恢复模块ETC ETC key:Extension of the softkey bar in the same menuETC 键：同级菜单扩展键FDB Product designation database 产品指定数据库FIFO First in First Out 先进先出FRA Frame module 帧频模块FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging 坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compensation 铣刀半径补偿FST Feed Stop 停止进给GUD Global User Data 全体用户数据HMS High-Resolution Measuring System 高分辨率测量系统HSA Main Spindle Drive 主轴驱动HW Hardware 硬件IM Interface Module 接口模块IM-S/R Interface Module(S=send/R=receive) 接口模块，S=发送/R=接收INC Increment 步进增量ISO-Code Special tape code,number of holes per character always even特殊纸带码，每个字符的孔数为偶数K1...k4 Channel 1 to Channel 4 通道1 到通道4KOP Ladder Diagram 梯形图KV Loop-Gain Factor 增益系数KUE Transformation Ratio 传动比LCD Liquid Crystal Display 液晶显示LED Light Emitting Diode 发光二极管显示LUD Local User Data 局部用户数据MB Megabyte 兆字节MD Machine Data 机床数据MK Measuring Circuit 测量回路MDA Manual Data Automatic 手动输入，自动执行MLFB Machine-readable product designation 机器可识别的产品代号MMC Man Machine Communication:User interface of the numerical controlsystem for operation,programming and simulation 人机通讯：系统操作界面，用操作，编程和模拟MPF Main Program File：NC part program(main program)NC 零件程序，主程序MPI Multi Point Interface 多点通讯接口MSTT Machine control panel 机床控制面板NC Numerical Control 数字控制NCK Numerical Control Kernel(numerical krnel with block preparation, traversing range etc.) 数字控制核心：具有程序段预处理,运行范围等等NCU Numerical Control Unit 数控单元NURBS Non Uniform Rational B Spline 非均值有理B样条NV Zero Offset 零点偏置OEM Original Equipment Manufacturer 原设备制造商OP Operator Panel 操作面板OPI Operator Panel Interface 操作面板接口PC Personal Comprter 个人计算机PCMCIA Personal Computer Menory Card International Association接口协议PG Programming Device 编程器PLC Programmable Logic Control 可编程逻辑控制器PRT Program Test 程序测试RAM Random Access Memory 随机存取存储器RISC Reduced Instruction Set Computer 处理器，具有指令组小、通过能力强ROV Rapid Override 快速修调RPA R Parameters Active(NCK memoty area for R parameter numbers) R 参数有效，NCK 中用于R 参数号的存储器区RTS Request To Send(control signal from serial data interfaces)发送请求：来自串行接口的控制信号SBL Single Block 单段SBL2 Single Block Decoding 译码单段SEA Setting Data Active(memory area for setting data in NCK)设定数据有效：用于NCK 中设定数据的存储区SD Setting Data 设定数据SKP Skip Block 程序段跳跃SM Signal Module 信号模块SPF Sub Program File 子程序文件SPS Programmable Logic Controller 可编程逻辑控制器SRK Cutter Radius Compensation 刀尖半径补偿SSFK Leadscrew Error Compensation 丝杠螺距误差补偿SSI Serial Synchronous Interface 串行同步接口SW Software 软件TEA Testing Data Active(with reference to the machine data) 测试数据有效：与机床数据有关TO Tool Offset 刀具补偿TOA Tool Offset Active(memory area for tool offset) 刀具补偿有效，用于刀补的存储区TRANSMIT Transform Milling into Turning(coordinate conversion on turning machines for milling)铣床转换为车床：车床坐标换算用于铣削加工VSA Feed drive(spindle) 主轴进给驱动V Bit type PLC variable PLC变量类型：位VB Byte type PLC variablePLC变量类型：字节WKZ Tool 刀具WZ Tool 刀具WZK Tool offset 刀具补偿ZOA Zero Offset Active(memory area for zero offsets) 零点偏置有效：零点偏置存储区好好看看啊手机了好久的约。
机床按键与报警显示中英对照
INSRT 插入程序DELET 删除程序EOB 完成一句 (END OF BLOCK)CAN 取消(EDIT 或 MDI MODE 情况下使用)INPUT 输入程序及代码OUTPUT START 输出程序及指令OFFSET 储存刀具长度、半径补当值AUX GRAPH 显示图形PRGRM 显示程序内容ALARM 显示发生警报内容或代码POS 显示坐标DGONS PARAM 显示自我诊断及参数功能RESET 返回停止CURSOR 光标上下移动PAGE 上下翻页数控机床中英文对照表ABS和REL——在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标ALL——全选，程序编辑时用PRGRM——程序（program）的缩写，用于查看程序NEXT——查看程序和查看参数时，下一页OPRT——在法那克系统中，选择编辑程序时，也就是按下PRGRM后，再按这个键，才能输入程序号HOST，CONECT——这两个是在系统与外界通信时用的，我没试过，不知道什么作用HELP——查看帮助信息SHIFT——换档键，有些键有两个字符，按下这个键，用来输入顶部那个字符ALTER——程序修改键，编辑程序时用INSERT——程序插入键，编辑程序时用EOB——程序结束符，在编辑程序时，没段程序结束时，要加这个符号CAN——取消键，用来取消输入INPUT——输入键，用来输入程序或参数POS——按此键显示当前机床位置画面PROS——按此键显示当前程序画面OFFSET——按此键显示刀具偏置画面SETTING——按此键显示刀具偏置设定画面SYSTEM——按此键显示系统信息及系统状态画面GRAPH——按此键显示加工时刀具轨迹的图形画面CUSTOM——按此键显示用户宏程序画面手动数据输入 (MDI)直接数字控制方法 (DNC)控制器单元或机控制器单元（MCU常见机床报警信息中英文对照T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL（X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD （刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警)MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR MAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALARM(气压低报警)MOTOR OVERLOAD(电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERRORDOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误) SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCKTRY TO RUN SPINDLE WHILE TAIL NOT LOCKSPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭) SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"" SWITCH ONHYDRAULIC MOTOR QF7 OFF（液压马达QF7关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED（液压过滤器阻止）HYDRAULIC OIL LEVEL LOW（液压油位低）HYDRAULIC FAN QF8 OFF（液压风扇QF8关闭）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF（冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK（内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF（内冷却液QF13关闭）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW（低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）IS LOW（润滑油低）DOOR OPEN（门打开）FRONT DOOR(R) OPEN（前门打开）LEFT DOOR OPEN（左门打开）LUBRICATION OIL QF23 OFF（润滑油QF23关闭）LUBRICATION PRESS LOW（润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED（门没有全部关闭）IN M06,MAG NOT READY（在M06，刀库未准备好）MAGAZINE NOT READY（刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET OFFZNOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG 关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG 机床抱闸错误PLEASE ADD 请加润滑油PROBE BATTERY VOLTAGE IS LOW 探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE（参数写使能）PMC EDIT ENABLE（PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION 主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR 因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC 电池SIEMENS常用缩略语A Output 输出ASCII American Standard Code for Information Interchange 美国信息交换标准代码AV Preparation for work 运行准备BA Operating mode 运行方式BAG Operating mode groups 运行方式组BB Ready for operation 准备好运行BCD Binary Coded Decimals 二-十进制BHG Hand-held terminal 手提终端BOF User interface 用户接口CNC Computerized Numerical Control 计算机化数字控制CP Communication Processor 通迅处理器CPU Central Processing Unit 计算机中央处理装置CR Carriage Return 托架折回CSB Central Service Board(PLC module) 中央维护板，PLC 模块CTS Clear To Send 发送使能DAU Digital-Analog Converter 数模转换器DB Data Block 数据块DIN German Industrial Standards 德国工业标准DIO Data Input/Output 数据输入/输出DRF Differential Resolver Function 差分功能DRY Dry Run 空运行DSB Decoding Single Block 译码单段DSR Data Send Ready 备用输入DW Data Word 数据字E Input 输入EIA-Code Special tape code,number of holes per characters always odd 特殊纸带码，每个字符的孔数为奇数EPROM Programm memory with fixed program 有固定程序的程序存储器E/R Controlled Supply and Energy Recovery Module 可控电源和能量恢复模块ETC ETC key:Extension of the softkey bar in the same menuETC 键：同级菜单扩展键FDB Product designation database 产品指定数据库FIFO First in First Out 先进先出FRA Frame module 帧频模块FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging 坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compensation 铣刀半径补偿FST Feed Stop 停止进给GUD Global User Data 全体用户数据HMS High-Resolution Measuring System 高分辨率测量系统HSA Main Spindle Drive 主轴驱动HW Hardware 硬件IM Interface Module 接口模块IM-S/R Interface Module(S=send/R=receive) 接口模块，S=发送/R=接收INC Increment 步进增量ISO-Code Special tape code,number of holes per character always even特殊纸带码，每个字符的孔数为偶数K1...k4 Channel 1 to Channel 4 通道1 到通道4KOP Ladder Diagram 梯形图KV Loop-Gain Factor 增益系数KUE Transformation Ratio 传动比LCD Liquid Crystal Display 液晶显示LED Light Emitting Diode 发光二极管显示LUD Local User Data 局部用户数据MB Megabyte 兆字节MD Machine Data 机床数据MK Measuring Circuit 测量回路MDA Manual Data Automatic 手动输入，自动执行MLFB Machine-readable product designation 机器可识别的产品代号MMC Man Machine Communication:User interface of the numerical controlsystem for operation,programming and simulation 人机通讯：系统操作界面，用操作，编程和模拟MPF Main Program File：NC part program(main program)NC 零件程序，主程序MPI Multi Point Interface 多点通讯接口MSTT Machine control panel 机床控制面板NC Numerical Control 数字控制NCK Numerical Control Kernel(numerical krnel with block preparation,traversing range etc.) 数字控制核心：具有程序段预处理,运行范围等等NCU Numerical Control Unit 数控单元NURBS Non Uniform Rational B Spline 非均值有理B 样条NV Zero Offset 零点偏置OEM Original Equipment Manufacturer 原设备制造商OP Operator Panel 操作面板OPI Operator Panel Interface 操作面板接口PC Personal Comprter 个人计算机PCMCIA Personal Computer Menory Card International Association 接口协议PG Programming Device 编程器PLC Programmable Logic Control 可编程逻辑控制器PRT Program Test 程序测试RAM Random Access Memory 随机存取存储器RISC Reduced Instruction Set Computer 处理器，具有指令组小、通过能力强ROV Rapid Override 快速修调RPA R Parameters Active(NCK memoty area for R parameter numbers)R 参数有效，NCK 中用于R 参数号的存储器区RTS Request To Send(control signal from serial data interfaces)发送请求：来自串行接口的控制信号SBL Single Block 单段SBL2 Single Block Decoding 译码单段SEA Setting Data Active(memory area for setting data in NCK)设定数据有效：用于NCK 中设定数据的存储区SD Setting Data 设定数据SKP Skip Block 程序段跳跃SM Signal Module 信号模块SPF Sub Program File 子程序文件SPS Programmable Logic Controller 可编程逻辑控制器SRK Cutter Radius Compensation 刀尖半径补偿SSFK Leadscrew Error Compensation 丝杠螺距误差补偿SSI Serial Synchronous Interface 串行同步接口SW Software 软件TEA Testing Data Active(with reference to the machine data) 测试数据有效：与机床数据有关TO Tool Offset 刀具补偿TOA Tool Offset Active(memory area for tool offset) 刀具补偿有效，用于刀补的存储区TRANSMIT Transform Milling intoTurning(coordinate conversion onturning machines for milling)铣床转换为车床：车床坐标换算用于铣削加工VSA Feed drive(spindle) 主轴进给驱动V Bit type PLC variable PLC变量类型：位VB Byte type PLC variablePLC变量类型：字节WKZ Tool 刀具WZ Tool 刀具WZK Tool offset 刀具补偿ZOA Zero Offset Active(memory area for zero offsets)零点偏置有效：零点偏置存储区。
机床按键与报警显示中英对照
法拉克：ALTER 修改程序及代码INSRT 插入程序DELET 删除程序EOB 完成一句 (END OF BLOCK)CAN 取消(EDIT 或 MDI MODE 情况下使用) INPUT 输入程序及代码OUTPUT START 输出程序及指令OFFSET 储存刀具长度、半径补当值AUX GRAPH 显示图形PRGRM 显示程序内容ALARM 显示发生警报内容或代码POS 显示坐标DGONS PARAM 显示自我诊断及参数功能RESET 返回停止CURSOR 光标上下移动PAGE 上下翻页数控机床中英文对照表ABS和REL——在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标ALL——全选，程序编辑时用PRGRM——程序（program）的缩写，用于查看程序NEXT——查看程序和查看参数时，下一页OPRT——在法那克系统中，选择编辑程序时，也就是按下PRGRM后，再按这个键，才能输入程序号HOST，CONECT——这两个是在系统与外界通信时用的，我没试过，不知道什么作用HELP——查看帮助信息SHIFT——换档键，有些键有两个字符，按下这个键，用来输入顶部那个字符ALTER——程序修改键，编辑程序时用INSERT——程序插入键，编辑程序时用EOB——程序结束符，在编辑程序时，没段程序结束时，要加这个符号CAN——取消键，用来取消输入INPUT——输入键，用来输入程序或参数POS——按此键显示当前机床位置画面PROS——按此键显示当前程序画面OFFSET——按此键显示刀具偏置画面SETTING——按此键显示刀具偏置设定画面SYSTEM——按此键显示系统信息及系统状态画面GRAPH——按此键显示加工时刀具轨迹的图形画面CUSTOM——按此键显示用户宏程序画面手动数据输入 (MDI)直接数字控制方法 (DNC)控制器单元或机控制器单元（MCU常见机床报警信息中英文对照T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL（X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD （刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警) MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERRORMAGAZINE NOT IN POSITION OR SENSOR ERROR AIR PRESSURE LOW ALARM(气压低报警)MOTOR OVERLOAD(电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERROR DOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误) SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCK TRY TO RUN SPINDLE WHILE TAIL NOT LOCK SPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭)SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ONHYDRAULIC MOTOR QF7 OFF（液压马达QF7关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED（液压过滤器阻止）HYDRAULIC OIL LEVEL LOW（液压油位低）HYDRAULIC FAN QF8 OFF（液压风扇QF8关闭）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF（冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK（内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF（内冷却液QF13关闭）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW（低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW（润滑油低）DOOR OPEN（门打开）FRONT DOOR(R) OPEN（前门打开）LEFT DOOR OPEN（左门打开）LUBRICATION OIL QF23 OFF（润滑油QF23关闭）LUBRICATION PRESS LOW（润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED（门没有全部关闭）IN M06,MAG NOT READY（在M06，刀库未准备好）MAGAZINE NOT READY（刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRD UNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZNOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG 关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG 机床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTERY VOLTAGE IS LOW 探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE（参数写使能）PMC EDIT ENABLE（PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION 主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERR CHANGE T STOPED BECAUSE NO AIR 因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC电池SIEMENS常用缩略语A Output 输出ASCII American Standard Code for Information Interchange 美国信息交换标准代码AV Preparation for work 运行准备BA Operating mode 运行方式BAG Operating mode groups 运行方式组BB Ready for operation 准备好运行BCD Binary Coded Decimals 二-十进制BHG Hand-held terminal 手提终端BOF User interface 用户接口CNC Computerized Numerical Control 计算机化数字控制CP Communication Processor 通迅处理器CPU Central Processing Unit 计算机中央处理装置CR Carriage Return 托架折回CSB Central Service Board(PLC module) 中央维护板，PLC 模块CTS Clear To Send 发送使能DAU Digital-Analog Converter 数模转换器DB Data Block 数据块DIN German Industrial Standards 德国工业标准DIO Data Input/Output 数据输入/输出DRF Differential Resolver Function 差分功能DRY Dry Run 空运行DSB Decoding Single Block 译码单段DSR Data Send Ready 备用输入DW Data Word 数据字E Input 输入EIA-Code Special tape code,number of holes per characters always odd 特殊纸带码，每个字符的孔数为奇数EPROM Programm memory with fixed program 有固定程序的程序存储器E/R Controlled Supply and Energy Recovery Module 可控电源和能量恢复模块ETC ETC key:Extension of the softkey bar in the same menuETC 键：同级菜单扩展键FDB Product designation database 产品指定数据库FIFO First in First Out 先进先出FRA Frame module 帧频模块FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging 坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compensation 铣刀半径补偿FST Feed Stop 停止进给GUD Global User Data 全体用户数据HMS High-Resolution Measuring System 高分辨率测量系统HSA Main Spindle Drive 主轴驱动HW Hardware 硬件IM Interface Module 接口模块IM-S/R Interface Module(S=send/R=receive) 接口模块，S=发送/R=接收INC Increment 步进增量ISO-Code Special tape code,number of holes per character always even特殊纸带码，每个字符的孔数为偶数K1...k4 Channel 1 to Channel 4 通道1 到通道4KOP Ladder Diagram 梯形图KV Loop-Gain Factor 增益系数KUE Transformation Ratio 传动比LCD Liquid Crystal Display 液晶显示LED Light Emitting Diode 发光二极管显示LUD Local User Data 局部用户数据MB Megabyte 兆字节MD Machine Data 机床数据MK Measuring Circuit 测量回路MDA Manual Data Automatic 手动输入，自动执行MLFB Machine-readable product designation 机器可识别的产品代号MMC Man Machine Communication:User interface of the numerical controlsystem for operation,programming and simulation 人机通讯：系统操作界面，用操作，编程和模拟MPF Main Program File：NC part program(main program) NC 零件程序，主程序MPI Multi Point Interface 多点通讯接口MSTT Machine control panel 机床控制面板NC Numerical Control 数字控制NCK Numerical Control Kernel(numerical krnel with block preparation,traversing range etc.) 数字控制核心：具有程序段预处理,运行范围等等NCU Numerical Control Unit 数控单元NURBS Non Uniform Rational B Spline 非均值有理B样条NV Zero Offset 零点偏置OEM Original Equipment Manufacturer 原设备制造商OP Operator Panel 操作面板OPI Operator Panel Interface 操作面板接口PC Personal Comprter 个人计算机PCMCIA Personal Computer Menory Card International Association 接口协议PG Programming Device 编程器PLC Programmable Logic Control 可编程逻辑控制器PRT Program Test 程序测试RAM Random Access Memory 随机存取存储器RISC Reduced Instruction Set Computer 处理器，具有指令组小、通过能力强ROV Rapid Override 快速修调RPA R Parameters Active(NCK memoty area for R parameter numbers)R 参数有效，NCK 中用于R 参数号的存储器区RTS Request To Send(control signal from serial data interfaces) 发送请求：来自串行接口的控制信号SBL Single Block 单段SBL2 Single Block Decoding 译码单段SEA Setting Data Active(memory area for setting data in NCK) 设定数据有效：用于NCK 中设定数据的存储区SD Setting Data 设定数据SKP Skip Block 程序段跳跃SM Signal Module 信号模块SPF Sub Program File 子程序文件SPS Programmable Logic Controller 可编程逻辑控制器SRK Cutter Radius Compensation 刀尖半径补偿SSFK Leadscrew Error Compensation 丝杠螺距误差补偿SSI Serial Synchronous Interface 串行同步接口SW Software 软件TEA Testing Data Active(with reference to the machine data) 测试数据有效：与机床数据有关TO Tool Offset 刀具补偿TOA Tool Offset Active(memory area for tool offset) 刀具补偿有效，用于刀补的存储区TRANSMIT Transform Milling into Turning(coordinate conversion onturning machines for milling)铣床转换为车床：车床坐标换算用于铣削加工VSA Feed drive(spindle) 主轴进给驱动V Bit type PLC variable PLC变量类型：位VB Byte type PLC variablePLC变量类型：字节WKZ Tool 刀具WZ Tool 刀具WZK Tool offset 刀具补偿ZOA Zero Offset Active(memory area for zero offsets) 零点偏置有效：零点偏置存储区。
数控机床设备资料中英文对照
数控机床设备资料中英文对照一：说明书名词解释：lubrication hole[机]润滑孔; [机]滑油孔; 加油孔; [机]注润滑油孔Pressure Lubrication[机]压力润滑; 强制润滑; [机]加压润滑lubrication device润滑装置; 润滑油; 润滑装配AUTO LUBE 自动润滑Spindle motor 主轴马达Hydraulic pump motor 油压马达Auto Cross feed motor 前后马达High Pressure Through Coolant刀具高压冷却系统once-through coolant system一次流过冷却系统Coolant through spindle油水别离机sp. through coolant主轴通过冷却液through coolant通过冷却剂coolant jet冷却剂喷嘴flood coolant motor洪水冷却电机base coolant/gun motor基地冷却剂/枪电动机mist collect motor雾收集电动机Coolant motor (for tools/chips) 切削水马达Chip conveyor motor 铁屑输送机马达ATC motor 储刀仓马达fan cooler风扇冷却器fan draught cooler冷风机fan cooler(for amp):风扇冷却器〔对放大器〔amplifier〕〕containment fan cooler平安壳风机冷却器fan-draught cooler风扇冷却器fan unit 风扇设备风扇单元风扇装置panel cooling 嵌入式降温panel door 镶板门panel heating 板壁供热tool counter工具柜台MAGAZINE CW 刀库正转MAGAZINE CCW 刀库反转 ...COUNTER 〔计数器〕TOTAL COUNTER〔总计数器〕Mate：配对物〔伴侣〕Rotation：旋转回转Caution：慎重radiator brake：散热器制动air duster blow gun吹尘器喷枪air-blow pipe喷气管Air Blow：鼓风Overload：超载overload protection防止过载，超载防护information overload信息过载；信息超载；信息超负荷overload capacity过载容量overload operation超负荷运行，超载运行thermal overload relay热继电器；热过载继电器overload current[电]过载电流 ; 过载电流过负荷电流dis connect jumper pin in case of using sub op存保方案连接跳线针如果使用子运算〔in case of using如果使用；usb op 子运算〕disconnect jumper pin断开连接跳线针beta-i servo ：β-i 伺服spindle amplifer:主轴放大器manual feed delay：手动进给延迟rigid tapping ontime：刚性攻丝准时z-axis cancel：z轴取消Current Tool Number现行刀具号Reset Current Tool恢复当前工具预设servo amp module伺服放大器模块optical fiber cable：光缆、光纤光缆sheet key板键Head sheet Key头型图要点key sheet键盘纸; 转印盘纸i series servo motor：i系列伺服电动机call light：警示灯lub. motor on :润滑泵接通〔lubricant润滑剂motor-on signal马达接通信号ATC forward：ATC 向前ATC reverse ：ATC反向Ball screw:滚珠丝杠Binary code :二进制DETACH:别离，脱开Follow-up ：位置跟踪Black format：程序段格式Tool post interference check：刀架碰撞检查Abnormal load detection：异常负载检测Manual handle interruption:手轮中断Ladder diagram:梯形图〔阶梯，关系图〕Tool counter：工具柜台Magazine：刀库Brake module：制动模块Machine side：机侧Twist pair：双绞线Main power source：主电源Wiring diagram：接线图Current：现时状态、现行状态Dual table ：双工作台Spare：备用件、预置Aux：辅助Brake on：制动器Mist ：雾状、雾Coolant tank capacity：冷却泵油箱容量Enclosure：外壳、套、附件Overload：过载Flag：标志Condition：条件Machine ready delay：机床准备延迟Encoder：编码器Etherent：以太网口Orientation：主轴定向Spindle positioning：主轴定位Fault：故障Motion：运转Dwell：停歇，保压Feed rate：进给率Interlock/start-lock:互锁/启动-锁Spindle speed arrival check：主轴速度到达检测concent for maintenance容许为维护AC reactor:交流电抗器APC：绝对位置编码器反应(Absolute position encoder feedback) arm in position z-axis interlock:手臂位置Z轴互锁Pressure：压力，压强，是……压迫Pressure valve[机]压力阀; [机]压力值; 止回阀; [机]回压阀air pressure气压; 空气压力; [建]工作气压; [物]气源压力consuming volume耗用量Oil：油Oller：n. 轮胎式压路机Capacity:n. 能力；容量；资格，地位；生产力bearing capacity[力]承载能力; [力]承载力; [力]承重能力; 支持力oil type 油的类型pumping n. [机] 抽吸；脉动；抽气效应v. 抽水〔pump的ing形式〕pumping out抽空; 扬水; 排出; 泵出pumping frequency[电子]泵频; 抽运频率; 泵送频率interval：间隔间距class interval[统计]组距; 组区间; 级距; 标度分组间隔Time interval[天]时间间隔; [天]时间区间; 时距; [天]时段interval scale[统计]区间尺度; 等距量表; [计]等距尺度; 等距量尺capacity：容量consuming：adj. 消费的；强烈的v. 消耗〔consume的ing形式distributor分配器metering n. 计量，[测] 测量；测光模式v. 以计量器计量〔meter的ing形式metering valve[机]计量阀; 限流阀; [机]限量阀; [机]配量阀metering jet量孔; [油气]测油孔; 计量喷流OPTION：选择〔选择功能块〕ARM:机械手ARM home position：机械手原点位置soft key cable：软键电缆PUNCH PANEL:开孔面板MOTHER BOARD:母版Name：名称Description：描述Connector：连接器Clamp：夹紧Unclamp：松开Lamp：灯noise filter：噪声滤波器二、操作面板中英文对照：ABS和REL——在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标ALL——全选，程序编辑时用PRGRM——程序〔program〕的缩写，用于查看程序NEXT——查看程序和查看参数时，下一页OPRT——在法那克系统中，选择编辑程序时，也就是按下PRGRM后，再按这个键，才能输入程序号HOST，CONECT——这两个是在系统与外界通信时用的，我没试过，不知道什么作用HELP——查看帮助信息SHIFT——换档键，有些键有两个字符，按下这个键，用来输入顶部那个字符ALTER——程序修改键，编辑程序时用INSERT——程序插入键，编辑程序时用EOB——程序完毕符，在编辑程序时，没段程序完毕时，要加这个符号CAN——取消键，用来取消输入INPUT——输入键，用来输入程序或参数POS——按此键显示当前机床位置画面PROS——按此键显示当前程序画面OFFSET——按此键显示刀具偏置画面SETTING——按此键显示刀具偏置设定画面SYSTEM——按此键显示系统信息及系统状态画面GRAPH——按此键显示加工时刀具轨迹的图形画面CUSTOM——按此键显示用户宏程序画面手动数据输入(MDI)直接数字控制方法(DNC)控制器单元或机控制器单元〔MCU〕法拉克：ALTER 修改程序及代码INSRT 插入程序DELET 删除程序EOB 完成一句(END OF BLOCK)CAN 取消(EDIT 或MDI MODE 情况下使用)INPUT 输入程序及代码OUTPUT START 输出程序及指令OFFSET 储存刀具长度、半径补当值AUX GRAPH 显示图形PRGRM 显示程序内容ALARM 显示发生警报内容或代码POS 显示坐标DGONS PARAM 显示自我诊断及参数功能RESET 返回停顿CURSOR 光标上下移动PAGE 上下翻页三、机床报警信息中英文对照：T WORD ERROR 〔T 码错误〕LOW OIL LEVEL 〔油位低〕SPINPLE FAULT 〔主轴故障〕SPINDLE ALARM 〔主轴报警〕EXTERNAL EMG STOP 〔急停按钮被按下〕AC NOT READY 〔交流盘未准备好〕SPINPLE LUBE FAULT 〔主轴润滑故障〕T CODE ERROR 〔T代码出错，非法T代码〕M CODE ERROR 〔M代码出错，非法M代码〕SERVO NOT READY 〔伺服未准备好〕NC NOT READY〔NC没准备好〕TURRET FAULT 〔转塔故障〕TURRET LIMIT 〔转塔限位〕DC 24V OPEN 〔直流24断开〕+24V NOT READY〔+24V没准备好〕GRAR DRIFT 〔档位漂移〕PLEASE AXIS RETURN HOME〔轴未回零〕PLEASE DRUM RETURN HOME〔刀库未回零〕AIRPRESSFAILURE〔气压故障〕UNCL TOOL FALL〔松刀失败〕AIR PRESSURE DROP 〔压缩空气压力过低〕CLAMP TOOL FALL〔夹刀失败〕DRUM NOT PARKED〔刀库未在原值〕X ZERO POINT NOT REACHED 〔X 轴未回零〕Y ZERO POINT NOT REACHED 〔Y 轴未回零〕Z ZERO POINT NOT REACHED 〔Z 轴未回零〕4TH ZERO POINT NOT REACHED 〔第4轴未回零〕X AXIS OVERTRAVL〔X轴超限〕Y AXIS OVERTRAVL 〔Y轴超限〕Z AXIS OVERTRAVL 〔Z轴超限〕COUNTER SWITCH REEOR 〔计数开关故障〕MASTERT RANSFER OVER TEMP 〔主变压器过热〕Z AXIS NOT AT FIRST REF POSITION 〔Z轴未在第一参考点〕SPINDLE ORIENTATION FALLURE 〔主轴定向失败〕TOOL DESENT OR TOOL DATA REEOR 〔刀具数据错误〕PLEASE UNLOAD THE TOOL ON SPRINELK 〔请卸下主轴上的刀〕PLEASE LOAD TOOL ON APINDLE 〔请装上主轴上的刀〕A AXIS UNCLAMP FAIL 〔A 轴松开失败〕A AXIS CLAMP FAIL 〔A 轴夹紧失败〕DRUM OUT TO APRONDLEIS FALL 〔刀库摆向换刀位失败〕MG SWING OVERLOAD〔刀库摆动过载〕DRUM BACK PARK IS FALL 〔刀库摆回原始位失败〕TURRENT MOTOR1 OVERLOAD 〔刀库移动电机过载〕COOLANT MOTOR OVERLOAD 〔冷却泵过载〕DRUM ATC FAULT 〔自动换刀失败〕TOOLS UNLOCKED 〔刀具未锁紧〕BATTERY ALARM 〔电池报警〕DRUM POSITION SWITCH ERROR 〔刀库位置检测开关故障〕DRUM NOW NOT AT PARK 〔刀库未在原始位置〕IT DANGOU TO MOVE DRUM 〔刀库禁动〕POT UO FAILOR POT NOT AT UP POSITION 〔刀套未在水平位〕POT DOWN FAIL 〔刀套翻下动作失败〕IT IS DANGOUR TO MOVE ARM 〔机械手禁动〕THE SPINDLE STATU IS ERROR 〔主轴状态错误〕ARM MOTOR OR ARM SWITCH FALL 〔机械手或机械手开关故障〕CENTRE LUBRICATION FALL 〔中心润滑故障〕THE WORK NOT CLAMPED 〔工件未夹紧〕AUTO TOOL CHANGE FAULT 〔自动换刀失败〕TOOL DATA OUT OF RANGE 〔指令刀具号超出范围〕THE ORDER TOOL NOW IN SPINDLE 〔目标刀具在主轴上〕THE THREE SPINDLE SWITCH FAULT 〔主轴上的接近开关〕THE CENTRE COOLANT IS LOWER 〔刀具内冷泵液位过低〕DRUM RETURN 1# POSITION FAULT 〔刀库自动回零失败〕SPINDLE OVERLOAD 〔主轴过载〕TURRENT MOTOR OVERLOAD 〔刀盘转动电机过载〕CHIP CONVEYER OVERLOAD 〔拉屑器过载〕HARD LIMIT OR SERVO ALARM 〔硬限位或伺服报警〕NO LUB OIL 〔无润滑油〕INDEX HEAD UNLOCKED 〔分度头未锁紧〕MT NOT READY〔机床没准备好〕MG OVERLOAD 〔刀库过载〕LUB EMPTY〔润滑无油〕AIR PRESSURE〔气压缺乏〕COOLANT NOT READY〔冷却没准备好〕LUBE EMPTY〔油雾油位低，润滑油位低〕LUB PRESSURE LOW〔润滑压力低〕CONVEY VERLOAD〔排屑过载〕LUB OVERLOAD〔润滑过载〕LUBE PRESSURE LOW〔油雾压力低〕SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警)MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR MAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALARM(气压低报警)MOTOR OVERLOAD(电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERRORDOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误)SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL〔主轴负荷异常〕TRANSDUCER ALARM〔传感器报警〕BED-HEAD LUBRICATE OFF〔床头润滑关闭〕EMG OFFHYDRAULIC CHUCK PRESS LOW〔液压夹头压力低〕HYDRAULIC TAIL PRESS LOW〔液压尾座压力低〕LUB 0IL LOW〔油压低〕TURRET CODE ERROR〔转塔码错误〕TURRET RUN OVERTIME〔转塔运行超时〕MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCKTRY TO RUN SPINDLE WHILE TAIL NOT LOCKSPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED〔X 轴被锁定〕Y AXIS IS LOCKED〔Y 轴被锁定〕Z AXIS IS LOCKED〔Z 轴被锁定〕A AXIS IS LOCKED〔A 轴被锁定〕SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭) SPINDLE ORIENTATION INCOMPLETE〔主轴定位不完全〕M FUNCTION NOT COMPLETE〔M 功能无法完成〕SPINDLE NOT IN GEAR POSITION〔齿轮不在主轴位置〕SPINDLE NOT CHANGED TO LOW GEAR〔主轴没有变为低档〕SPINDLE NOT CHANGED TO HIGH GRAR〔主轴没有变为高档〕MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ONHYDRAULIC MOTOR QF7 OFF〔液压马达QF7关闭〕HYDRAULIC TEMPRETURE HIGH〔液压使用温度高〕HYDRAULIC FILTER BLOCKED〔液压过滤器阻止〕HYDRAULIC OIL LEVEL LOW〔液压油位低〕HYDRAULIC FAN QF8 OFF〔液压风扇QF8关闭〕HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF〔冷却液电机QF12关闭〕COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK〔内冷却堵塞〕SPINDLE COOLANT MOTOR QF14 OFF〔主轴冷却液电机QF14关闭〕INNER COOLANT QF13 OFF〔内冷却液QF13关闭〕MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW〔低气压〕SPINDLE COOLANT MOTOR FAULT〔主轴冷却液电机故障〕LUB.OIL IS LOW〔润滑油低〕DOOR OPEN〔门翻开〕FRONT DOOR(R) OPEN〔前门翻开〕LEFT DOOR OPEN〔左门翻开〕LUBRICATION OIL QF23 OFF〔润滑油QF23关闭〕LUBRICATION PRESS LOW〔润滑油位低〕IN ADJUST,MAG CAN'T EXCHANGE T〔在调整，刀库不能交换T〕NOT ALL DOOR CLOSED〔门没有全部关闭〕IN M06,MAG NOT READY〔在M06，刀库未准备好〕MAGAZINE NOT READY〔刀库未准备好〕POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZ NOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG 关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG 机床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTERY VOLTAGE IS LOW 探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE〔参数写使能〕PMC EDIT ENABLE〔PMC编辑使能〕CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION 主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR 因为缺少压空交换停顿THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC电池四、SIEMENS常用缩略语：SIEMENS常用缩略语A Output 输出ASCII American Standard Code for Information Interchange 美国信息交换标准代码AV Preparation for work 运行准备BA Operating mode 运行方式BAG Operating mode groups 运行方式组BB Ready for operation 准备好运行BCD Binary Coded Decimals 二-十进制BHG Hand-held terminal 手提终端BOF User interface 用户接口CNC Computerized Numerical Control 计算机化数字控制CP Communication Processor 通迅处理器CPU Central Processing Unit 计算机中央处理装置CR Carriage Return 托架折回CSB Central Service Board(PLC module) 中央维护板，PLC 模块CTS Clear To Send 发送使能DAU Digital-Analog Converter 数模转换器DB Data Block 数据块DIN German Industrial Standards 德国工业标准DIO Data Input/Output 数据输入/输出DRF Differential Resolver Function 差分功能DRY Dry Run 空运行DSB Decoding Single Block 译码单段DSR Data Send Ready 备用输入DW Data Word 数据字E Input 输入EIA-Code Special tape code,number of holes per characters always odd 特殊纸带码，每个字符的孔数为奇数EPROM Programm memory with fixed program 有固定程序的程序存储器E/R Controlled Supply and Energy Recovery Module 可控电源和能量恢复模块ETC ETC key:Extension of the softkey bar in the same menuETC 键：同级菜单扩展键FDB Product designation database 产品指定数据库FIFO First in First Out 先进先出FRA Frame module 帧频模块FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging 坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compensation 铣刀半径补偿FST Feed Stop 停顿进给GUD Global User Data 全体用户数据HMS High-Resolution Measuring System 高分辨率测量系统HSA Main Spindle Drive 主轴驱动HW Hardware 硬件IM Interface Module 接口模块IM-S/R Interface Module(S=send/R=receive) 接口模块，S=发送/R=接收INC Increment 步进增量ISO-Code Special tape code,number of holes per character always even特殊纸带码，每个字符的孔数为偶数K1...k4 Channel 1 to Channel 4 通道1 到通道4KOP Ladder Diagram 梯形图KV Loop-Gain Factor 增益系数KUE Transformation Ratio 传动比LCD Liquid Crystal Display 液晶显示LED Light Emitting Diode 发光二极管显示LUD Local User Data 局部用户数据MB Megabyte 兆字节MD Machine Data 机床数据MK Measuring Circuit 测量回路MDA Manual Data Automatic 手动输入，自动执行MLFB Machine-readable product designation 机器可识别的产品代号MMC Man Machine Communication:User interface of the numerical control system for operation,programming and simulation 人机通讯：系统操作界面，用操作，编程和模拟MPF Main Program File：NC part program(main program)NC 零件程序，主程序MPI Multi Point Interface 多点通讯接口MSTT Machine control panel 机床控制面板NC Numerical Control 数字控制NCK Numerical Control Kernel(numerical krnel with block preparation, traversing range etc.) 数字控制核心：具有程序段预处理,运行范围等等NCU Numerical Control Unit 数控单元NURBS Non Uniform Rational B Spline 非均值有理B样条NV Zero Offset 零点偏置OEM Original Equipment Manufacturer 原设备制造商OP Operator Panel 操作面板OPI Operator Panel Interface 操作面板接口PC Personal Comprter 个人计算机PCMCIA Personal Computer Menory Card International Association 接口协议PG Programming Device 编程器PLC Programmable Logic Control 可编程逻辑控制器PRT Program Test 程序测试RAM Random Access Memory 随机存取存储器RISC Reduced Instruction Set Computer 处理器，具有指令组小、通过能力强ROV Rapid Override 快速修调RPA R Parameters Active(NCK memoty area for R parameter numbers)R 参数有效，NCK 中用于R 参数号的存储器区RTS Request To Send(control signal from serial data interfaces)发送请求：来自串行接口的控制信号SBL Single Block 单段SBL2 Single Block Decoding 译码单段SEA Setting Data Active(memory area for setting data in NCK)设定数据有效：用于NCK 中设定数据的存储区SD Setting Data 设定数据SKP Skip Block 程序段跳跃SM Signal Module 信号模块SPF Sub Program File 子程序文件SPS Programmable Logic Controller 可编程逻辑控制器SRK Cutter Radius Compensation 刀尖半径补偿SSFK Leadscrew Error Compensation 丝杠螺距误差补偿SSI Serial Synchronous Interface 串行同步接口SW Software 软件TEA Testing Data Active(with reference to the machine data) 测试数据有效：与机床数据有关TO Tool Offset 刀具补偿TOA Tool Offset Active(memory area for tool offset) 刀具补偿有效，用于刀补的存储区TRANSMIT Transform Milling into Turning(coordinate conversion onturning machines for milling)铣床转换为车床：车床坐标换算用于铣削加工VSA Feed drive(spindle) 主轴进给驱动V Bit type PLC variable PLC变量类型：位VB Byte type PLC variablePLC变量类型：字节WKZ Tool 刀具WZ Tool 刀具WZK Tool offset 刀具补偿ZOA Zero Offset Active(memory area for zero offsets) 零点偏置有效：零点偏置存储区五、常用缩写：启动start STRT停顿stop ST运行run正转forward FWD反转reverse REV加速accelerate减速reduce RED低速low L中速medium M高速high H主轴方向spindle direction向前forward FWD向后backward向左left L向右 right R诊断：DGNOS信息：MSG操作员：OPER参数：PARAM目录：DIR取代：ALTER公共地线，公共线：COM六、知识补充：金属切削 metal cutting机床 machine tool金属工艺学 technology of metals刀具 cutter摩擦 friction联结 link传动 drive/transmission轴 shaft弹性 elasticity频率特性 frequency characteristic 误差 error响应 response定位 allocation机床夹具 jig动力学 dynamic运动学 kinematic静力学 static分析力学 analyse mechanics拉伸 pulling压缩 hitting剪切 shear扭转 twist弯曲应力 bending stress强度 intensity三相交流电 three-phase AC磁路 magnetic circles变压器 transformer异步电动机 asynchronous motor几何形状 geometrical精度 precision正弦形的 sinusoid交流电路 AC circuit机械加工余量 machining allowance 变形力 deforming force变形 deformation应力 stress硬度 rigidity热处理 heat treatment退火 anneal正火 normalizing脱碳 decarburization渗碳 carburization电路 circuit半导体元件 semiconductor element 反应 feedback发生器 generator直流电源 DC electrical source门电路 gate circuit逻辑代数 logic algebra外圆磨削 external grinding内圆磨削 internal grinding平面磨削 plane grinding变速箱 gearbox离合器 clutch绞孔 fraising绞刀 reamer螺纹加工 thread processing螺钉 screw铣削 mill铣刀 milling cutter功率 power工件 workpiece齿轮加工 gear mechining齿轮 gear主运动 main movement主运动方向 direction of main movement进给方向 direction of feed进给运动 feed movement合成进给运动 resultant movement of feed合成切削运动 resultant movement of cutting合成切削运动方向 direction of resultant movement of cutting 切削深度 cutting depth前刀面 rake face刀尖 nose of tool前角 rake angle后角 clearance angle龙门刨削 planing主轴 spindle主轴箱 headstock卡盘 chuck加工中心 machining center车刀 lathe tool车床 lathe钻削镗削 bore车削 turning磨床 grinder基准 benchmark钳工 locksmith锻 forge压模 stamping焊 weld拉床 broaching machine拉孔 broaching装配 assembling铸造 found流体动力学 fluid dynamics流体力学 fluid mechanics加工 machining液压 hydraulic pressure切线 tangent机电一体化 mechanotronics mechanical-electrical integration 气压 air pressure pneumatic pressure稳定性 stability介质 medium液压驱动泵 fluid clutch液压泵 hydraulic pump阀门 valve失效 invalidation强度 intensity载荷 load应力 stress平安系数 safty factor可靠性 reliability螺纹 thread螺旋 helix键 spline销 pin滚动轴承 rolling bearing滑动轴承 sliding bearing弹簧 spring制动器 arrester brake十字结联轴节 crosshead联轴器 coupling链 chain皮带 strap精加工 finish machining粗加工 rough machining变速箱体 gearbox casing腐蚀 rust氧化 oxidation磨损 wear耐用度 durability随机信号 random signal离散信号 discrete signal超声传感器 ultrasonic sensor集成电路 integrate circuit挡板 orifice plate剩余应力 residual stress套筒 sleeve扭力 torsion冷加工 cold machining电动机 electromotor汽缸 cylinder过盈配合 interference fit热加工 hotwork摄像头 CCD camera倒角 rounding chamfer优化设计 optimal design工业造型设计 industrial moulding design 有限元 finite element滚齿 hobbing插齿 gear shaping伺服电机 actuating motor铣床 milling machine钻床 drill machine镗床 boring machine步进电机 stepper motor丝杠 screw rod导轨 lead rail组件 subassembly可编程序逻辑控制器 Programmable Logic Controller PLC 电火花加工 electric spark machining电火花线切割加工 electrical discharge wire - cutting 相图 phase diagram热处理 heat treatment固态相变 solid state phase changes有色金属 nonferrous metal陶瓷 ceramics合成纤维 synthetic fibre电化学腐蚀 electrochemical corrosion车架 automotive chassis悬架 suspension转向器 redirector变速器 speed changer板料冲压 sheet metal parts孔加工 spot facing machining车间 workshop工程技术人员 engineer气动夹紧 pneuma lock数学模型 mathematical model画法几何 descriptive geometry机械制图 Mechanical drawing投影 projection视图 view剖视图 profile chart标准件 standard component零件图 part drawing装配图 assembly drawing尺寸标注 size marking技术要求 technical requirements刚度 rigidity内力 internal force位移 displacement截面 section疲劳极限 fatigue limit断裂 fracture塑性变形 plastic distortion脆性材料 brittleness material刚度准那么 rigidity criterion垫圈 washer垫片 spacer直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear直齿锥齿轮 straight bevel gear运动简图 kinematic sketch齿轮齿条 pinion and rack蜗杆蜗轮 worm and worm gear虚约束 passive constraint曲柄 crank摇杆 racker凸轮 cams共轭曲线 conjugate curve范成法 generation method定义域 definitional domain值域 range导数\\微分 differential coefficient求导 derivation定积分 definite integral不定积分 indefinite integral曲率 curvature偏微分 partial differential毛坯 rough游标卡尺 slide caliper千分尺 micrometer calipers攻丝 tap二阶行列式 second order determinant逆矩阵 inverse matrix线性方程组 linear equations概率 probability随机变量 random variable排列组合 permutation and combination气体状态方程 equation of state of gas动能 kinetic energy势能 potential energy机械能守恒 conservation of mechanical energy 动量 momentum桁架 truss轴线 axes余子式 cofactor逻辑电路 logic circuit触发器 flip-flop脉冲波形 pulse shape数模 digital analogy液压传动机构 fluid drive mechanism机械零件 mechanical parts淬火冷却 quench淬火 hardening回火 tempering调质 hardening and tempering磨粒 abrasive grain结合剂 bonding agent砂轮 grinding wheel。
2016年最新版数控机床报警信息中英文对照
2016年最新版数控机床报警信息中英文对照WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z 轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL（X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）关注我们的微信公众号shukongzhpngguo，获取更多数控技术文章。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
常见数控机床报警信息（中英文对照），太全啦！平时在操作数控机床时，总会遇到报警的信息提示，有些英文的对照不免让新学者头疼，小编特意整理了一些常见的数控机床报警信息中英文对照版的，没事翻翻就当小小工具书了！T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z 轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL（X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD （刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警)MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR MAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALARM(气压低报警)MOTOR OVERLOAD(电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERROR DOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误) SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFF太HYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCK TRY TO RUN SPINDLE WHILE TAIL NOT LOCK SPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭)关注我们的微信公众号shukongzhpngguo，获取更多数控技术文章。
SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ONHYDRAULIC MOTOR QF7 OFF（液压马达QF7关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED（液压过滤器阻止）HYDRAULIC OIL LEVEL LOW（液压油位低）HYDRAULIC FAN QF8 OFF（液压风扇QF8关闭）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF（冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK（内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF（内冷却液QF13关闭）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW（低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW（润滑油低）DOOR OPEN（门打开）FRONT DOOR(R) OPEN（前门打开）LEFT DOOR OPEN（左门打开）LUBRICATION OIL QF23 OFF（润滑油QF23关闭）LUBRICATION PRESS LOW（润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED（门没有全部关闭）IN M06,MAG NOT READY（在M06，刀库未准备好）MAGAZINE NOT READY（刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZ NOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG 关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG 机床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTERY VOLTAGE IS LOW 探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE（参数写使能）PMC EDIT ENABLE（PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION 主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR 因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC电池有些还没有翻译，仅供参考。