GPS使用说明书
GPS使用说明书
GPS 使用说明一、仪器的架设1、打开三脚架及仪器盒，将脚架大致安平，将基准站和天线安装好，然后插线，天线带的线头插在电台下面（螺旋），将电瓶带的线头，单线头插在基准站蘑菇头下部（红点对准），将双线插在电台上端插口（红点对准），检查线头插接无误时，再将夹子夹在电瓶的两极（红色夹正极，蓝色插负极），检查无误后依次打开电台和基准站的电源。
二、仪器的连接与设置1、打开1、新建任务（如20160309），选择西安80坐标系统；2、保存任务；3、打开新建的任务20160309；4、在文件中查看任务属性、当前坐标参数（取消“水平平差、垂直平差”的“√”；5、在配置下找到手薄端口设置，打开选择蓝牙连接，先绑定基准站（＃＃＃＃＃＃61）；6、测量下打开开启基准站接收机，进入界面后，在右下角点击断开；返回后在测量下再一次打开开启基准站接收机进行设置，输入点号(如1），用卷尺测量地面到基准站蘑菇头下沿的高度，在天线高度一栏填写测量的高度（如1.60），选择天线底部，然后点击“此处”，然后点击下一步（不用修改如何设置），在然后确定，完成基准站连接；7、在配置下找到手薄端口设置，打开选择蓝牙连接，绑定移动站（＃＃＃＃＃＃41）；8、测量下打开开启移动站接收机，进入界面后，在右下角点击断开；返回后在测量下再一次打开开启移动站接收机进行设置，按电台上面最上面的按钮打开通道，在手薄上选择的通道和电台打开的通道保持一致，然后下一步、下一步，完成移动站的连接。
三、点校正1、在测量下打开测量点界面（地形点）将已知点的两点坐标进行测量（如A1、A2），在测量之前观察界面中的天线高度与移动站的天线高度是否保持一致，如果不一致就先将其调整成一致在进行测量；在键入下键入已知点坐标X、Y、H（注意将点号与原来测量的点号区分开，如JA1、JA2）；2、在测量下最后一行找到“点校正”，打开点校正，点击左下角的增加，进入界面后点击第一行“...”，选择A1，再点击第三行”...”，选择JA1，点击右下角的确定，再选择增加，进入界面后点击第一行“...”，选择A2，再点击第三行”...”，选择JA2，然后点击“计算”，计算后选择确定、是，返回主界面；3、在测量下打开测量点界面，测量（注意区分点号如A01）已知点A1或者A2,然后在文件下找到点管理器，打开点管理器，查看A01坐标与已知点A1坐标进行比较，点校正完成。
GPS卫星导航仪操作手册
GPS卫星导航仪操作手册欢迎使用本公司产品!★感谢您购买本公司的产品，在使用产品之前，请认真阅读本说明书。
当您开始使用本产品时，本公司认为您已经认真地阅读了本说明书;★本说明书提供的信息，经仔细核对，务求精准。
如有任何印刷或翻译错误，本公司不承担因此产生的后果;★此说明书的所有著作权都归本公司所有，不得随意复制或翻译此说明书的全部或部分进行商业活动，本公司保留对此说明书内容的最终解释权;★请先仔细阅读本《使用说明书》的操作说明与指示，并只使用原厂提供的配件，以免造成无法预期的损坏。
如果您未依照正确的程序使用本系统或连接不兼容的配件，此行为将导致保修自动失效，甚至可能危害您及他人的安全。
对此，本公司不承担任何责任;★本导航仪属于高技术产品，其中包括操作系统和其他第三方提供的软件。
制造商在硬件的制造过程和软件的开发以及运用过程中已经尽到了充分的注意义务，以确保产品能够正常工作。
如果产品发生故障，制造商除了根据品质保证规定承担维修责任之外，对于用户因使用本产品而导致的财产损害和经济损失不承担任何赔偿责任;★本导航器使用的电子地图由第三方提供，该第三方拥有的电子地图的版权受到法律保护，除了在本导航器上使用以外，用户不得复制或用于其他用途;★对于本导航器使用的电子地图中信息的有效性、完整性和准确性本导航器制造商不做任何明示或默示的担保或保证，对于由电子地图中存在缺陷给用户造成的任何人身损害和财产损失本产品制造商均不承担任何赔偿责任;★本手册中的图片仅供参考，请以实物为准。
目录第一章产品概述 (3)1.1产品特色 (3)1.2注意事项 (3)1.3GPS使用常识 (3)1.4产品包装 (4)第二章基本操作 (4)2.1屏幕显示说明 (4)2.2电池操作说明 (5)2.3开/关机操作说明 (6)2.4使用车载固定架固定导航仪 (6)2.5使用触摸笔 (6)第三章系统操作 (6)3.1音乐播放功能 (6)3.2视频播放功能 (7)3.3图片浏览功能 (8)3.4文本阅读功能 (9)3.5FLASH播放功能 (10)3.6预警系统 (10)3.7蓝牙功能(可选) (12)3.8游戏功能 (20)3.9工具 (20)3.10系统设置 (21)3.11GPS信息 (22)3.12导航功能使用 (22)第四章维护和简单故障处理 (22)4.1产品规格 (22)4.2简单故障排除 (22)第一章产品概述1.1产品特色ü5英寸高清晰、真彩色纯平显示屏，触控输入。
GPS车辆追踪器用户手册说明书
GPS Vehicle tracker(GPS+GSM+SMS/GPRS)User Manual(Version 5.0N)This user manual has been specially designed to guide you through the functions and features of your GPS vehicle tracker.1. Accessories:▶Device▶Power cord▶Relay▶Microphone▶SOS alarm cable & button▶User Manual2. SpecificationsDimension 106(L) x 54(W) x 16(H) mm Weight 96gBackup Battery 450mAh / 3.7VOperation Temperature-25℃-60℃Humidity 5% - 95%Standby Time 60hoursGSM Frequencies 850/900/1800/1900 MHz GPRS Class 12GPS Channel 20GPS Sensitivity -159dBmAcquisition Sensitivity -144dBmPosition Accuracy 10mTTFF （Open Sky）Cold Start: ＜38s Warm Start：＜15s Hot Start：＜2sGSM/GPS Antenna Built-in designLED Indicator GSM-green, GPS-blue, Power-redData Transmit TCP, SMSGeo-fence View any existing Geo-fence in the mapSpeeding Alarm Report when speeds higher than the pre-set value. Low Power Alarm Alarm when backup battery is running outNon-movement Detection Movement alarm based on built-in 3D motion sensor Mileage Report Track by time/distance intervalRemote Control Cut off petrol/electricity3. LED IndicationsGPS LED Indicator - BlueFlashing (interval 0.1s) Searching GPS signalSolid blue GPS fixOFF No GPS fix or initializingGSM LED Indicator - GreenQuick flashing (interval 0.1s) GSM initializingSlow flashing (flash 0.1s every 2s) Receive GSM signal normally Solid green Connected to GSM network OFF No GSM signalPower Status - RedFlashing (interval 0.1s) Low batterySlow flashing (interval 0.2s) Full chargeSlow flashing (flash 0.1s every 2s) Normal operatingSolid Red ChargingOFF Low battery/Power offIgnition detection indication: three LED indicators take turns flashing.4. Getting StartedPlease follow below instructions for ensuring safe and correct use.4.1 Install the SIM cardPlace the SIM card into the device with the gold-colored side facing down.Note: Make sure there is enough credit on the SIM card. If you will be using the GPRS function, you should pay attention to the current SIM card GPRS charge.4.2 Install the deviceYou need to choose somewhere that it won't be found, because the whole point of fitting covert GPS vehicle tracker is the secrecy element.Installation please refers to below picture.NOTE:1. Any high power devices such as reversing radar, anti-theft device or communication equipment would affect the signal of the device.2. All metallic cases of the windshield will attenuate the signal on the tracking device. It’s simply due to the shielding effects of the metal compound of the case.4.3 Wiring configurationLine No. Specification Color Instruction1. 2 Keypod Orange / Orange Connect to SOS button3. 4 MIC-,MIC+ Black / Red Connect to Microphone5 TX Green Sending data (TX) / backup6 RX White Receiving data (RX) / backup7 GND Black Ground wire8 MOTOR Yellow Connect to relay control line9 ACC White Connect to ACC ignition10 V- Black(thick) Negative side of 12V/24Vcar storage battery.11 V+ Red(thick)Notes of the relay wiringThe relay wiring of pump: oil connectors of both ends are a fine white line (85) and a fine yellow line (86). The fine white line (85) is connected to vehicle positive power (+12V). The fine yellow line is connected to the device relay control line.Cut off the positive connection line of the pump; then connect in series to the relay N.C. contact (thick green line 87a) and the other end to relay COM contact (thick green line 30).4.4 Device wiring diagramPlease choose the right relay (12V-standard / 24V-optional) for the proper installation. 4.5 Power/ACC/Tele-cutoff(petrol/electricity) control line (4 pin) 1. Your device comes with a power cord and is designed to use only manufacturer-specified original device. The red line is positive while the black one is negative (the side should not be connect with ground wire).2. The ACC line (white) connects to ACC switch of the vehicle. Please be sure to connect the ACC line; otherwise the device will enter ignition detectionstatus when disconnect the ACC line. If you don’t need to anti-theft temporarily, just connect the ACC line to the positive side in parallel.3. Tele-cutoff (petrol/ electricity) control line (yellow) is connected to pin 86 of the Tele-cutoff (petrol/ electricity) relay (equal to the yellow line of the relay socket).4. USB cable (3 pin)Firmware updating interface/expanded function to reserve space.5. MIC line (2 pin)Externally connect to microphone for voice monitoring function.6. SOS line (2 pin)Externally connect to SOS switch for SOS function.5. Quick Operation InstructionsOperation Tips: To properly use the device, common parameters should be set before initial use. This can be done by using the parameter editor or by sending SMS commands to the device. (“,”should be English comma and no space before and after the comma)5.1 APN settingTo connect default platform , please send the SMS command below:APN command format: APN,APN's Name#E.g: APN,internet# (“internet” is the APN of carrier)The device will reply “OK” if setting successfully.Note: The APN of some countries have user name and password, you may need to send SMS command as following:APN,APN name,user name,password#E.g: APN,internet,CLIENTE,AMENA#5.2 DNS settingTo connect other platform, please send the two SMS commands bleow: Command format：SERVER,1,DNS,Port,0#E.g:SERVER, 1,,8841,0#It will reply “OK” after set successfully.5.3 ON /OFF GPRSWhen you want to disable GPRS, you can SMS command to the SIM card number which used in the device.Command format:GPRS ON：GPRSON,1#GPRS OFF：GPRSON,0#It will reply “OK” after set successfully.5.4 Add specific numberSMS command to the device to set the SOS number.SOS,A,No.1,No.2,No.3#“A” means to add new numbers, for example:SOS,A,135****5991,135****5992,135****5993#If there is only one SOS number, you can appoint a specific number as SOS number. And the null means no adding.For example:SOS,A,135****5991#means to set the first number as SOS number SOS,A,,135****5992#means to set the second number as SOS number SOS,A,,,135****5993#means to set the third number as SOS numberIf set successfully, there is a “success” reply SMS.5.5 Delete specific numberBefore deleting specific number, please check its corresponding code. For the code, please SMS “PARAM#” to the device.SMS command to the device to delete the number.SOS,D,serial NO.1,serial NO.2,serial NO.3#“D” means to delete the number, for example:SOS,D,1# means to delete the first numberSOS,D,3# means to delete the third numberIf you want to delete more than one numbers, you can send this command: SOS,D,1,3# means to delete the first and third numbers.If you forget serial number of the mobile number you want delete, you can send this command:SOS,D,mobile number# means to delete the mobile number directly.For example:SOS,D,135****2360#meanstodeletethe135********directly.After deleting the SOS number, it will receive “Delete number 135XXXXXXXX success! specific number total 2” for successful deleting of the specific number.5.6 Set the center numberIf you want to cut off/restore oil by SMS command, you have to set a centernumber firstly. Only the center number can send the cut off/restore oil command to the device. You can set your own mobile number as center number.The command for setting center number is:CENTER,A,mobile number#Forexample:CENTER,A,159****3401#If set successfully, there is an “OK” reply message.NOTE：Only the SOS number can be used to set center number successfully.5.7 Delete the center numberSMS command to the device to delete the center number.The command is:CENTER,D#For example:CENTER,D#If set successfully, there is an “OK” reply SMS.NOTE：Only the SOS number can be used to delete center number successfully.Only SOS phone number can send this command successfully to set the center number. There is only one center number can be set.5.8 Check parameter settingSend command to the terminal, you can check the parameter setting. Command format: PARAM#e.g.: PARAM# Information replied:IMEI: 353419032348877 ---IMEI number of the device;Timer: 10,10; ---GPS data uploading Interval;SENDS:5; --- the GPS working time when ACC is OFF;SOS:159****3401;---SOSnumbers,maximum3SOSnumberscanbeset and used for alarm and monitoring;CenterNumber:159****3401;---only1centernumbercanbesetandused for cutting off /restoring oil command;Sensorset:10,1,5,180 --- detect 5 vibrations in 10s; the alarm delay is 180s; Defense time: 10; --- the defense delay is 10 minute;TimeZone:E,8,0; --- set time zone; default as E8.The replied information contains IMEI number, GPS data uploading interval, SENDS, SOS, center number, sensor set time interval, defense time and time zone.5.9 Check GPRS parametersSMS command format：GPRSSET#Eg：GPRSSET#Reply message：GPRS:ON //GPRS on/off status// Currently use APN:,,; //APN setting information// Server:1,,8841,0; //platform information// URL:/maps?q=; //preset web link setting information // 5.10 GPS data uploading intervalThe default sending interval is 10,10. It means when ACC ON ,the device will upload positioning data to platform server every 10s.when ACC OFF ,the device will upload positioning data to platform server every 10s.Users can modify sending interval by SMS“TIMER,time1(seconds), time2(seconds)”The time1&time2 ranges from 10-18000sFor example:TIMER,10,20#It means when ACC ON ,the device will upload positioning data to platform server every 10s.when ACC OFF ,the device will upload positioning data to platform server every 20s.5.11 Sensor alarm time settingWhen the vehicle power is off and ACC is in low-level, if ACC is off over 10 minutes, the device will enter sensor alarm state. In this case, if the vehicle vibrates for a few times, it will activate the vibration alarm system. If the vehicle battery is still not on (ACC is in low level) after 3 minutes, the device will start vibration alarm.SMS format: “DEFENSE,TIME(minutes)#” The time ranges from 1 to 60 mins.For example: DEFENSE,15#. It means when ACC is in low level for 15mins, it will enter sensor alarm status (vehicle power is off)NOTE：1. Preset SOS numbers when send SMS alarm messages and calls2. If there is no need for vibration alarm, please SMS SENSOR,0# to close it.5.12 Restore to factory settingSMS command format: “FACTORY#” to set all parameter to default factory value. Once received “OK”, it succeeds.5.13 Reboot deviceWhen there is something wrong with the link of GPRS, e.g., The parameter setting of the device is correct, but you can't track the car on the platform. At this moment you can send a command to the device to reboot the device. The format is: RESET#After receiving this command, the device will reboot after 1mins.6. Operation of device6.1 Power on/ Power offPower on: Once insert a valid SIM card and connect all the wires, turn on the device, then Power LED will flash first, During signal searching process, GSM and GPS LED will flash. Once GPS LED keeps solid light, it means the device has been located and it starts to work.Power off: Just turn off the power switch.The device will begin to upload positioning data to server once inserting a valid SIM card and power on. During the working time, it can upload data to server every 10 seconds.6.2 Check location1. Via SMS1.1 SMS “WHERE#”, to the SIM number of device. The device will send a location message automatically. You can get the coordinates. If the device does not search any information of location, it will send “No data” to the cell phone.Example:Lat:N22.571285,Lon:E113.877115,Course:42.20,Speed:0.0740,DateTime:10-11-23 22:28:511.2 SMS “URL#”, to the SIM number of device. The device will send a location Google Map link. If the device does not search any information of location, it will send “No data” to the cell phone.Example:<Date Time：10-11-23 23:42:51> /maps?q=N22.571490,E113.8771032. Via platformGo to the platform website offered by dealers to check your vehicle location.6.3 SOS alarmIn emergent case, press SOS for 3s to activate SOS alarm. Then the device will send SOS SMS to preset specific numbers and then dial the numbers in circles until the call is picked up. At the meantime, the device will upload SOS alarm data to the server. And it will send:SOS Alarm! <DateTime:11-06-17 14：53：06>，/maps?q=N22576713,E113.916585Note: The specific numbers should be preset, just refer to 6.46.4 Wire cut-off alarmWhen the electricity supply of device is cut off, it will activate cut-off alarm. In this case, the device will send related SMS to the specific numbers and dial the numbers in circles. If nobody answers, the call just keeps 3 loops at most. At the meantime, the device will upload SOS alarm data to the server. And it will send:Cut Power！<Date Time:11-06-17 14：53：06>，/maps?q=N22576713,E113.916585Note: The specific numbers should be preset, just refer to 6.46.5 Low battery alarmWhen the device is only working with battery, once the internal voltage of battery is less than 3.7V, device will send low battery alarm sms to specific number and alarm on platform.Low battery alarm sms content example: “Attentionbattery too low, please charge.” Which means the battery is to low, to inform user charging it i n time. Note: The specific numbers should be preset, just refer to 6.46.6 Vibration alarmThe vibration alarm function is off by default. To activate this function, please send the following command: SENALM, ON#. The alarm will be sent to both the service platform and SOS numbers.When vehicle power is off, ACC status is low, and if the lead time of low ACC is more than 10 minutes （settable）, device will activate security alarm. When the security alarm is on, once the vehicle vibrates for several times, the alarm will be activated; in the next 3 minutes, if vehicle power is still off（ACC status is low）, device will start alarm. At this time, it will send alarm message to the service platform with the latitude and longitude, while the platform will reply the Chinese address. Then the terminal will send vibration alarm message to SOS numbers with the Chinese address, and call the SOS numbers in cycle. If nobody answers, it will stop calling after 3 loops.If the Chinese address can not be acquired for certain reason, the terminal will send a message with the website link to the SOS numbers.e.g.:Sensor Alarm！<11-23 14:53>,/maps?q=N22576713,E113.916585Note:1.The SOS numbers should be preset.2.Send “SEN ALM, OFF#” to turn off the vibration alarm.6.7 Voice monitoringWhen the special number cell phone dial device, ringing for 10 seconds, it will enter voice monitoring status. At this time, caller can monitoring the sound in vehicle. Incoming call from non special number will not activate voice monitoring function.Note:To realize this function, please set special number beforehand.The SIM card put into the device should be equipped with caller identification.6.8 Oil cut-off1. Via platformSend oil cut-off command on platform. To make sure the security of vehicle, tracker can only indicate to cut off oil when GPS is in valid position status, and the speed is less than 20KM/H or in static. Platform account password is needed when sending oil cut off command.2. Via SMSFirstly, you should set a center number. Please refer to 6.6.Only center number can send the command to the device to cut off and restore oil.The format is: RELAY,1#After the command is carried out, it will reply “Cut off the fuel supply: Success! Speed:0 Km/h”. If the command didn't carry out, it will reply the reason about fail to carry out.Note: To ensure the safety of the driver and the car, this command is valid only under two conditions: the GPS is located; the speed is less than 20km/h 6.9 Restoring Oil1. Via platformWhen the alarm is off, sending recover oil commands manually. Device will restore oil supplying, and vehicle will work normally again.Platform account password is needed when sending oil cut off command.2. Via SMSOnly center number can send the command to the device to restore oil.The format is: RELAY,0#After the command is carried out, it will receive “Restore fuel supply:Success!”6.10 Over speed AlarmWhen the car is moving over a limited speed in average in a limited time period, then the device will send over speed alarm SMS to user.To turn on the over speed function, please send below SMS command: SPEED,ON/OFF,Time,Limited speed,uploading mode#Speed alarm switch:ON/OFF default:OFFTime range (seconds):5-600s(default as 20s)Limited speed range(km/h):1-255km/h. default:100Mode:0/1. default:1 way of alarming,0 means GPRS only,1 meansSMS+GPRSExample:SPEED,ON,20,100,1#Means when the car is moving over 100km/h in average in 20 seconds,the device will send over speed alarm to user7．Web based tracking online activationThe GPRS web based tracking platform allows real time tracking with the latest Google maps. There is also a playback feature that allows you to view where the vehicle has been for up to 30 days in the past making it ideal for fleet management.8．Trouble shootingIf you are having trouble with your device, try these troubleshooting procedures before contacting a service professional.Problems Causes SolutionsFail to connect platform The fuse blows Replace the fuse ACC ignition disconnected Turn on ACC with keyFail to connect network Wrong installation of SIMcardCheck SIM card installation(Refer to 4.1 Install SIM card) Filth on the SIM card ironsurface.Clean itUseless SIM Contact internet serviceproviderImproper installation Check installation of device(Refer to 4.2 Install the device) Beyond GSM service area Use it in effective GSM serviceoffer areaBad signal Try again in a better signalareaFail to charge The voltage is unsuitable Connect with power withsuitable voltage Improper connection Check connection withcharger1. The warranty is valid only when the warranty card is properly completed, and upon presentation of the proof of purchase consisting of original invoice indicating the date of purchase, model and serial No.of the product. Wereserve the right to refuse warranty if this information has been removed or changed after the original purchase of the product from the dealer.2. Our obligations are limited to repair of the defect or replacement the defective part or at its discretion replacement of the product itself.3. Warranty repairs must be carried out by our Authorized Service Centre. Warranty cover will be void, even if a repair has been attempted by any unauthorized service centre.4. Repair or replacement under the terms of this warranty does not provide right to extension or renewal of the warranty period.5. The warranty is not applicable to cases other than defects in material, design and workmanship.Maintenance RecordShenZhen Concox Information Technology CO.,LtdTel: +86 755 2912 1200Fax: +86 755 2912 1290E-mail:**************.Add: 4/F, Building B, Gaoxinqi Industrial Park,Liuxian 1st Road, No.67 Bao'an District, Shenzhen DateServiced by Product ModelIMEI NumberFaultDescriptionsCommentsWarranty instructions and service。
GPS 北斗定位模块说明书
GPS/北斗定位模块说明书GPS/北斗定位模块使用说明书V2.4济南智泽贸易有限公司目录1.产品介绍 (1)1.1.产品概述 (1)1.2.产品特点 (1)1.3.技术指标 (1)1.4.产品尺寸 (1)1.5.硬件接口 (2)2.通信协议 (3)2.1.通信协议 (3)2.2.寄存器定义 (4)3.协议详解 (6)3.1.读保持寄存器 (6)3.2.读取版本号 (6)3.3.读取设备地址 (7)3.4.读取设备波特率 (7)3.5.读取奇偶校验位 (7)3.6.读取定位数据（RMC） (8)3.7.定位数据（RMC）解析 (8)3.8.修改设备地址（广播） (9)3.9.修改波特率 (9)3.10.修改奇偶校验位 (9)4.保修期限 (10)5.技术支持 (10)6.联系方式 (10)7.免责声明 (10)1.产品介绍1.1.产品概述GPS/北斗定位模块，是一款具有GPS定位和北斗定位的双模定位终端，可以快速、精确定位位置。
定位模块内含双模定位芯片，快速定位位置，并且将定位信息以RS485接口和Modbus协议的方式提供给用户使用，串口波特率最高可达115200bps，可以通过PC机设置软件或串口命令轻松控制，使用方便快捷。
1.2.产品特点⏹同时支持GPS定位和北斗定位⏹串口波特率自定义，支持2400～115200bps⏹串口支持全双工和半双工串口通讯，支持RS485收发自动切换⏹模块串口波特率等参数可通过PC机或串口命令配置⏹RS485带TVS、过流等保护⏹提供天线状态诊断，提供天线开路、短路等状态信息1.3.技术指标环境参数⏹工作温度：-40℃~80℃⏹工作湿度：5%~95%RH，无凝露供电⏹工作电压：DC5~28V⏹功耗：≤0.3W定位精度⏹出色的定位功能，支持BDS/GPS/GLONASS卫星导航系统的单系统定位，以及任意组合的多系统联合定位⏹冷启动捕获灵敏度：-148dBm跟踪灵敏度：-162dBm⏹定位精度：2.5米（CEP50）⏹内置天线检测及天线短路保护功能1.4.产品尺寸产品尺寸长x宽x高为：95mm x50mm x30mm，其中95mm包含长度80mm和两个安装孔15m图1-1产品尺寸1.5.硬件接口图1-2硬件接口硬件接口定义见表1-2硬件接口定义。
(完整word版)GPS北斗接收机说明书
GPS/北斗接收机使用说明书北京华星北斗智控技术有限公司第1页目录前言 (3)注意事项 (4)第一章产品介绍 (5)1。
1 主要特点 (6)1。
2 灵活的测量模式 (6)第二章性能参数 (8)2。
1 技术参数 (8)2.2 电气参数 (9)第三章安装应用 (10)3。
1 供电说明及设备安装 (10)3。
2 网络的应用说明 (11)第四章硬件功能说明 (21)4。
1 主机外观 (21)4.2 面板及接口说明 (22)4。
3 SD/SIM 卡的安装 (26)第2页第五章常见问题 (27)5。
1 故障分析 (27)5。
2 常见问题及其解决方法 (27)前言关于本手册本手册对GPS/北斗的安装、使用方法及有关技巧进行了详细的介绍。
用户应该仔细阅读，并边读边用，以求达到最佳使用效果。
本手册版权归北京华星北斗智控技术有限公司。
在著作权保护的范围内，未经本公司书面同意，禁止对其进行翻印、改编等行为。
本产品符合国家认定的企标：Q/VCPV 1—2011《测地型GPS 接收机》。
第3页注意事项1 使用仪器前请认真阅读产品使用说明；2 用户不能自行拆卸仪器，若发生故障，请与供应商联系;3 请使用指定品牌稳压电源，并严格遵循仪器的标称电压，以免对电台和接收机造成损害；4 请使用原厂电池及附件，使用非专用电池、充电器可能引起爆炸、燃烧等意外情况，使用非原厂附件不享有保修资格；5 使用充电器进行充电时，请注意远离火源、易燃易爆物品，避免产生火灾等严重的后果;第4页6 请勿将废弃电池随意丢弃，须根据当地的有关特殊废品的法规处理；7 电台在使用中可能产生高温.使用时请注意防止烫伤；减少、避免电台表面不必要的遮蔽物,保持良好的通风环境；8 禁止边对蓄电池充电边对电台供电工作；9 请不要长时间在高增益天线下，长时间使用电台时应保持1—1。
5 米以外，避免辐射伤害；10 雷雨天请勿使用天线和对中杆，防止因雷击造成意外伤害；11 请严格按照用户手册中的连线方法连接您的设备，各接插件要注意插接紧,电源开关要依次打开；12 不要在没有切断电源的情况下对各连线进行插拔；13 各连接线材破损后请不要再继续使用，请及时购买更换新的线材，避免造成不必要的伤害。
GPS使用说明书
使用说明书
1、GPS基本用健说明
本机只适用于日常巡线作
用，不能打接电话或是发送短
信。
1、电源开关键：长按此
健可以可关机或开机；操作时，
按此健可以可以返回上一菜
单，长按此键可以返回待机界
面。
2、音量健：“+”可以曾大声
音，“—”可以减小声音。
3、手电筒开关键：上下拨动
可以启停夜间手电功能。
4、确认健：按此键可以确定
所选功能。
5、导航键：可以上下翻动光
标。
6、FM健：是收音机开启收
音机功能。
7、键盘锁：可以拨动键盘锁
开关将键盘锁定或是开启。
2、使用方法：
2.1、电池装好后，长按电源键，GPS将开机。
2.2、开机后待读卡成功后，显示屏上方将显示在等图标，
这样为正常状态，正常后，为便于携带，把键盘锁锁上。
2.3、
2.3．1、
2.3．2、
3、注意事项：
3.1、GPS使用过程中，不能进水、烘烤（电池会爆炸）、摔打等。
3.2、GPS要时常保证电池有电状态。
GPS使用使用说明
eTrex Venture（中文）——奇遇使用手册合众思壮隆重推出中文输入功能完善面积计算器人性化界面第一章序言说明书介绍感谢您购买eTrex Venture（奇遇）GPS接收机——我们不停努力的结果，为了可以使您的新型GPS接收机发挥最大的用途，并且了解所有的操作细节，您可以花些时间阅读一下本手册。
手册由四部分组成：一、序言部分二、速查部分介绍了一些Venture的细节、主要操作页面和基本导航方式三手册部分提供了使用Etrex Venture 的所有细节。
四、附录部分包括一些有关附件，说明书，维修向导，主题索引等方面的信息。
标准配置包括主机1个牵引绳索1根中文说明书1本本手册中，所有的按键将使用黑体字，所有的菜单选项将用“”括起来。
GPS介绍全球定位系统（Global Positioning System - GPS）是美国从本世纪70年代开始研制，历时20年，耗资200亿美元，于1994年全面建成，具有在海、陆、空进行全方位实时三维导航与定位能力的新一代卫星导航与定位系统。
经近10年我国测绘等部门的使用表明，GPS以全天候、高精度、=自动化、高效益等显著特点，赢得广大测绘工作者的信赖，并成功地应用于大地测量、工程测量、航空摄影测量、运载工具导航和管制、地壳运动监测、工程变形监测、资源勘察、地球动力学等多种学科，从而给测绘领域带来一场深刻的技术革命。
随着全球定位系统的不断改进，硬、软件的不断完善，应用领域正在不断地开拓，目前已遍及国民经济各种部门，并开始逐步深入人们的日常生活。
GPS系统的特点:1、全球，全天候工作：能为用户提供连续，实时的三维位置，三维速度和精密时间。
不受天气的影响。
2、定位精度高：单机定位精度优于10米，采用差分定位，精度可达厘米级和毫米级。
3、功能多，应用广：随着人们对GPS认识的加深，GPS不仅在测量，导航，测速，测时等方面得到更广泛的应用，而且其应用领域不断扩大GPS发展历程GPS实施计划共分三个阶段：第一阶段为方案论证和初步设计阶段。
GPS导航系统用户指南说明书
Traveling To Your DestinationSave Current LocationThis option tells the system to store the current location for later use. It does not change or cancel the route instructions you are using at the time to reach a destination.For example, you are following the system's directions to get to a destination. You are sitting at a stoplight and notice a curio shop on the corner. You do not have time to visit it right now, but you would like to in the future. This option saves the location of the intersection so you can select it as a destination at a later date.To save the location (while thevehicle is stopped), touch the vehicle position icon. When the current address is displayed, touch "Save Current Location." After the location is saved, select "Return" to return to the Map screen.The current location is saved in the previous destination list. Use the Previous Destination option in the Main Menu to select it. It will appear in the list as "Save" followed by the location.Navigation SystemTraveling To Your DestinationGPS Signal Strength Green — Strong Yellow — WeakNot shown — No signalNorth Pointer(In 1/20, 1/8, and 1/2 mile map scales, touch tochange map orientation)Time to DestinationMap Scale Adjustment (Appears only when you press Zoom In/Out buttons)Map Scale(Miles per half inch)Blue line — Calculated route White — HospitalYellow — Shopping Mall Orange — University Dark Green — ParkMedium Green — Golf CourseGray — Airport/Stadium/Business Light Blue — Body of WaterCurrent LocationCurrent RoadNavigation SystemMap ScreenDirection to DestinationDistance toDestinationTraveling To Your DestinationLandmark IconsLandmark icons will be shown in the screen if you select the "Show Icon on Map" in the "Set-up Screen". See "System Setup" on page 60.Going Off the RouteIf you leave the calculated route,"Off-route" (manual) or"Recalculating" (automatic) is displayed at the top of the screen.The system will recalculate the route from your current location anddirection to the desired destination;then give you a new route instruction.This recalculation is doneautomatically unless you set it to manual in the Setup Menu. See "System Setup" on page 60.Auto RecalculationIf this option is set to "Automatic"you will see. "Recalculating" flash at the top of the screen for several seconds as the system recalculates the route. This is followed by a new route instruction.Manual RecalculationIf this option is set to "Manual", you will hear a tone when the "Off-route"message is displayed. You mustpress the Joystick or "ReCal" icon in the screen before the system will recalculate your route.Navigation SystemTraveling To Your DestinationModifying the RouteSeveral functions in the system allow you to view the route the system has calculated. You can then have the system recalculate portions of the route. This is helpful if you are aware of road conditions along the calculated route that you wish to avoid.With the map screen displayed, you can push the MAP/GUIDE button at any time to display the guidance screen. With the guidance screen displayed, move the Joystick left or right to see the Direction List. This shows you all the route instructions between your current location and your destination.Instructions that have already been executed cannot be displayed.Push the joystick down to see the upcoming route instructions one at a time. Each push displays the next in-struction in the sequence. Push the joystick up to move backwardthrough the sequence to the current instruction. The display returns to the current route instruction in about 10 seconds if you stop pushing on the joystick.Navigation SystemTraveling To Your DestinationPressing the MENU button with either the map screen or theguidance screen displayed changes the display to:This menu lets you cancel or modify the current calculated route.DetourSelect this option if you encounter an unexpected obstacle, such as a closed road or extremely heavy traffic congestion. The system will calculate a route from your current location that detours you off the original route, and then back onto it after a certain distance.Avoid a StreetThis option lets you delete a street or streets from the current calculated route. This is helpful if you know of road construction or other snags on the prescribed route.Plan New TripSelecting this option cancels the current route and destination. The display returns to the "Main Menu".Back to Current RouteSelecting this option returns you to the original guidance screen.Navigation System。
GPS定位器 说明书
GPS定位器使用说明书1安装说明1.1连接线说明DC+ 电源正极ACC 点火线GND 地线pOff 断油/断电控制线1.2安装前检测:1、检查配件主机、4Pin连接线、油路控制器、说明书2、SIM卡购买SIM手机卡（支持GSM/3G网络），如果开通GPRS功能，可以实现网上查车，如果开通来电显示功能，能进行电话远程监听。
设备没有SIM卡，不能正常工作。
1.3安装调试步骤1) 检测电源按接线图安装完成后,通电,LED指示灯会闪,如果不亮,表示设备供电不正常或损坏。
2) LED光灯状态指示检查◆亮1秒灭1秒表示GSM注册成功,约三十秒左右。
◆亮0.1秒灭2.9秒表示GPS定位,约四十五秒左右。
◆如果绿灯快闪(亮0.1秒,灭0.1秒) 超过三分钟后，可能SIM卡未插好,或设备损坏。
◆常亮表示GSM注册网络成功，并且GPS定位。
3) 拨打电话在LED灯常亮后,拨打设备的SIM号码,如果能通，即工作正常,可以进行短信操作或网络设置。
1.4安装注意事项●GPS天线与GSM天线内置,注意安装位置,否则会定不到位.●主机不防水，工作温度-40~60℃,注意固定位置。
●油路控制器分为12V和24V，安装时，注意与汽车供电电压是否一致。
2短信操作说明短信命令格式为：A******,功能序号，参数其中A表示命令开始，******为设备操作密码，初始化密码为000000，参数视具体的功能序号而定。
将短信发送到设备中的手机卡上，设备会自动回复应相的短信。
短信全部采用半角，如果密码错误、格式错误，设备将不会回复短信。
2.1位置请求（000）短信格式：A******, 000例如：A000000, 000设备收到短信后，回复位置信息，格式如下：Longitude E114.04577 Latitude N22.32405 08-10-20 17:38:30，如果没有定位，则经纬度时间都是0，为无效值，时间为格林威治时间，如北京为东8区，小时加8才能与本地时间一致。
GPS导航器操作手册说明书
Table of ContentsIntroduction (2)Important Safety Information (3)System Controls (4)Screen 4 MENU button (5)MAP/GUIDE button (5)CANCEL b utton (5)ZOOM button (5)SETUP icon (5)JOYSTICK (5)A/C button (5)System Start-up (6)Main Menu (7)Address (7)Intersection (7)Phone No. (POI) (7)Places (7)Map I nput (7)Personal Addresses (8)Previous Destination (8)Today's Destinations (8)Selecting By Address (9)Change State (9)Selecting the City (11)Selecting the Street Address...... 13Selecting By Intersection. (15)Selecting the City (16)Selecting the Street (18)Selecting By Phone No. (POI) (21)Selecting By Places (22)Name (22)Category (25)Selecting By Previous Destination (32)Selecting By Map Input (33)Current Position (33)A City (34)State 36Continental U SA (38)Selecting by Today's Destinations (39)Adding Destinations To The List (39)Selecting Destinations From the List (40)Editing the List (41)Traveling T o Your Destination (42)The Map Screen (46)Save Current Location (47)Landmark Icons (49)Going Off the Route (49)Modifying the Route (50)Personal Addresses (52)Entering a PIN (52)Entering Personal Addresses (53)Updating a Personal Address (57)Selecting a Personal Address Asa Destination (58)System Setup (60)Bright (60)Volume (60)Display (60)Reroute (61)Address (61)Location Correction (62)Personal PIN (63)Clock (63)Information (63)Show Icon on Map (64)System Security (65)System Limitations (66)Customer Assistance (68)DVD R emoval (69)Non-detailed Coverage (70)Detailed Coverage Areas (71)Climate Control System (76)Navigation SystemRefer to 2003 TL O wner's Manual for more information.User AgreementAlpha Indexv wIntroductionYour Acura Navigation System is a highly-sophisticated location system that uses satellites and a map database to show you where you are and to help guide you to a desired destination.The Navigation System receives signals from the Global Positioning System, a network of 24 satellites in orbit around the earth. By receiving signals from several of these satellites, the Navigation System can determine the latitude and longitude of your car.In addition, a gyroscopic sensor and a speed sensor in your car keep track of the direction and speed of travel at all times.The Navigation System applies thislocation, direction, and speedinformation to the maps and calcu-lates a route to the destination youenter. As you drive to thatdestination, the System providesguidance.The Navigation System is easy to use.The locations of many places ofbusiness and entertainment arealready entered in the system. Youcan select any of them as a desti-nation by pressing only one or two ofthe controls.If a desired destination is not in thesystem's database, you can enter itsaddress and the system will directyou to it. This destination can besaved for reuse at a later date.As you drive, the Navigation Systemprovides visual and audio drivinginstructions so you do not have totake your eyes off the road. Theseinstructions are provided in advanceof the actual driving maneuver soyou have time to slow down andchange lanes if necessary.Read this manual thoroughly so youare familiar with all the NavigationSystem's features. Afterwards, keepthis manual in the glove box of yourvehicle so you can refer to at anytime.Navigation SystemImportant Safety InformationThe Navigation System can distract your attention from the road if you focus on the screen or operate the system's controls while driving.You should always enter information into the system before you begin driving. Then, as you drive, you can listen to the audio instructions or glance at the screen.Operating the NavigationSystem controls while you aredriving can take your attentionaway from the road, causing acrash in which you could beseriously injured or killed.Enter information into thesystem only when your car isstopped.The Navigation System is designedto provide route information to helpyou reach your destination. However,this route guidance may sometimesconflict with road conditions such asstreet closures, road construction,and detours.Additionally, the system itself hascertain limitations (see page 66).Therefore, you must verify the audioand visual route informationprovided by the system by carefullyobserving the roadway, signs andsignals, etc. If you are unsure,proceed with caution. Always useyour own good judgment, and obeytraffic laws while driving.Navigation System。
GPS北斗定位模块用户手册.doc说明书
GPS/北斗定位模块使用说明书文档版本：V1.2目录1.产品介绍 (3)1.1产品概述 (3)1.2功能特点 (3)1.3设备技术参数 (3)1.4产品选型 (3)2.设备使用说明 (4)2.1设备安装前检查 (4)2.2接口定义 (4)3.配置软件安装及使用 (5)3.1软件选择 (5)4.通信协议 (6)4.1通讯基本参数 (6)4.2数据帧格式定义 (6)4.3寄存器地址 (7)4.4通讯协议示例以及解释 (8)4.4.1读取设备地址0x01的定位状态 (8)4.4.2读取设备地址0x01的经度 (8)4.4.3修改地址 (9)5.联系方式 (10)6.文档历史 (10)附录：壳体尺寸 (11)1.产品介绍1.1产品概述我公司研发生产的GPS/北斗定位模块，是一款具有GPS定位和北斗定位的双模定位终端，可以快速、有效、精确定位位置。
GPS/北斗定位模块内含双模定位芯片，可快速定位位置，并且将定位信息以RS232/485接口和ModBus协议的方式提供给用户使用，并可以通过PC 机设置软件或串口命令轻松控制，使用方便快捷。
1.2功能特点同时支持GPS定位和北斗定位（北斗二号和北斗三号1-63号全部卫星）采用WGS84世界大地坐标系，精准定位经纬度信息可实时读取对地速度、对地航向、海拔高度等信息串口波特率自定义，支持1200~115200bps模块串口波特率等参数可通过PC机或串口命令配置RS232/485带TVS、过流等保护提供天线状态诊断，提供天线开路、短路等状态信息1.3设备技术参数供电DC7~30V功耗0.348W使用环境工作温度-20℃~+60℃，0%RH~95%RH非结露通信接口RS232/485接口可选；通信波特率：1200~115200可设天线接口接我公司提供的GPS+北斗双频天线定位精度 2.5m（CEP50）海拔高度典型精度：±10m对地速度<0.36km/h（1σ）1.4产品选型RS-公司代号GPSBDS-GPS北斗定位模块N01-RS485（ModBus-RTU协议）N02-RS232（标准RS232-DB9接口）1GPS北斗定位模块外壳2.设备使用说明2.1设备安装前检查设备清单■GPS北斗定位模块1台■产品合格证、保修卡等■GPS+北斗双频天线安装尺寸：Φ2.5mm88mm2.2接口定义序号标识说明1DC10-30V电源输入设备供电10-30VDC宽压供电2Ant北斗+GPS双频天线3通信设备485通信灯4运行设备运行灯5电源正电源输出正6电源负电源输出负7485A通信：485-A8485B通信：485-B注：通信灯在设备485通信时亮0.1s，设备运行灯正常工作（定位成功）时亮0.5s，熄灭0.5s，异常（未定位成功）时亮0.1s，熄灭0.9s，且模块只需要一端供电就可以正常工作，另一端电源是为后级供电而准备，如不对后级进行供电，可悬空。
马歇尔GPS快速入门指南说明书
GPS 快速入门指南恭喜您购买了马歇尔GPS 。
您会发现它不仅仅只是一台顶尖的追踪产品。
客户不断反馈告诉我们，它从根源上改善了鹰猎这项运动，这在几年前是无法想象的。
我们希望它会成为您鹰猎装备中不可或缺的一件工具。
如何开始使用您的新GPS 系统：1.从您Apple 设备上的App Store 下载官方APP ：“ AeroVision4”。
2.确保您Apple 设备的蓝牙功能已打开。
3.点击手机屏幕上的APP 图标，打开AeroVision4。
4.允许APP 启用定位服务。
以上步骤完成后，APP 将显示您所在区域的地图，该地图的中心位置会显示一个红点（即您Apple 设备的GPS 定位位置*）。
5.用电磁棒触碰您中继器的电源图标以启动中继器（数据接收器）。
6.在AeroVision APP 中，点击左上角的Marshall 马歇尔图标以打开“ 设置”菜单。
您将在“设置”菜单的顶部看到您的中继器序列号。
点击此序列号以连接您的中继器和您的Apple 设备。
7.在户外视野良好，可以看清天空的情况下，将电池安装到您的RT GPS 发射头中。
8. 发射头一旦获取到GPS 信号，LED 指示灯将闪烁绿色灯光，绿色（启动）然后橙色（搜索定位卫星），并且将在2-3分钟内变成蓝色。
9. 观看这些视频教程以熟悉您的马歇尔GPS 系统。
教程视频简短且按主题排列，教程里包含您现在和未来将会用到的基本操作知识。
随着您使用GPS 系统经验的增长和新问题的出现，可以反复观看教程视频以发现新的基础操作知识。
我们将教学视频直接放于APP 中以方便客户查看。
如需在线观看视频，请访问https:///cn/。
使用腿部搭载发射头的用户注意事项：所有发射头均配有尾部弹簧夹。
如需拆卸尾部弹簧夹，请扭转松开天线保护套。
松开后您会看见有一个蓝色垫圈固定着弹簧夹。
向下拉弹簧夹和垫圈，来回摆动直到它们松脱。
卸下弹簧夹后，重新将垫圈和天线保护套安装回发射头即可。
北斗星二代GPS定位器使用说明书
GPS定位器使用说明书目录一、前言二、产品基本参数三、安装四、开始使用设备五、设备功能详解l短信功能5.1基本功能5.1.1获取位置信息5.1.2围栏5.1.3定时定位5.1.4断油电，通油电5.1.5 省电模式5.2防护模式5.2.1防盗报警5.2.2震动灵敏度设置5.2.3超速提醒5.3设备维护操作5.3.1设备重启5.4设备特殊参数设置5.4.1时区设置5.4.2数据通讯时间设置5.5其他功能l网络功能六、常见问题七、短信命令总表1一、前言非常感谢您使用本公司产品！该产品是本公司定位器系列中的一款新品。
该产品集GPS全球卫星定位系统、移动通信和因特网络平台于一体，性能稳定、精确、灵敏，使用方法简单，积小巧，便于安装与使用。
产品核心功能：本产品通过GPS 卫星定位系统，准确获取设备的地理位置，用户可通过手机短信及网络（电脑网络地址：www. ；手机网络地址/wap）来提取设备的地理位置信息，并对目标进行实时监控。
声明本公司对因用户的错误操作及不当维修所引起的个人数据资料丢失和意外损坏的情况不负任何责任，也不对由此造成的间接损失负责。
未经本公司授权许可，不得以任何形式或任何方式复制、传播、转录本手册的任何部分。
二、产品基本参数尺寸：40*58*14.5mm工作电压：DC: 6~30V工作环境：-25 ~ +80C(工作温度) 40% to 80% RH(工作湿度)频段：850/900/1800/1900MHzGPRS : class 12,TCP/IP.GPS: U-BLOX 7频率：L1, 1575.42 MHzGPS 敏感度：-159dBm定位精度：10m(2D RMS)工作电流：小于30MA,(12V). 小于20MA(24V)省电模式电流：4MA(12V)2三、安装1. 红线接电瓶电源正极6~30V DC2. 黑线接电瓶电源负极3. 黄线接继电器的86脚。
85接地。
继电器的30脚和87A串接在油泵线上.4. 绿线接ACC或者其他报警装置；可选作SOS键设备安放建议位置：AB3A B注：避免雨水淋湿，安装时设备一定要正面朝上，并且正上方不可有金属遮蔽物。
GPS定位器使用手册
GPS定位器使用手册
1、第一步：打来手簿，开启管理软件点击配置选项→手簿端口配置
→配置搜索→搜索到蓝牙某某某某（移动站PIN号）→绑定→退出→确定。
2、基准站、移动站信号灯及按键的名称和作用
红色按键（开关机键）红色指示灯（电源指示灯）蓝色指示灯（卫星
接收指示灯）绿色指示灯（接收基准站信号指示灯，1S/1次）黄色指示
灯（数据指示灯）3.、启动→点击测量（点击图标）→启动移动站接收器
4.、文件→新建任务→输入任务名称
5.、配置→坐标系管理→点管理器→查看中央子午线（每个地方不一样）和投影高（一般是甲方提供或默认为0）。
6.、成果桩导入手簿方法：用某l表格制作好原始坐标数据更改为（某、Y、Z）格式，保存时选择CSV格式，保存好后重命名后缀调为dat
格式。
拷贝dat文件到手簿。
将手簿和计算机连接，找到移动设备，将
dat文件拷贝到Built—in→RTKCE文件包内。
拷贝完后再手簿上操作将
文件导入。
点击文件→导入→当地点（类型选择为callfile）确定。
完
成后导入成功。
7.当基准站关机后再开启时，要进行点的校对。
在控制点处点击手簿（测量→测量点→确定），（点击文件→元素管理器→点管理→选择测量
点→点击详细→替换测量点位控制点）完成后对当前控制点进行点放样）。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
GPS 使用说明
一、仪器的架设
1、打开三脚架及仪器盒，将脚架大致安平，将基准站和天线安装好，然后插线，天线带的线头插在电台下面（螺旋），将电瓶带的线头，单线头插在基准站蘑菇头下部（红点对准），将双线插在电台上端插口（红点对准），检查线头插接无误时，再将夹子夹在电瓶的两极（红色夹正极，蓝色插负极），检查无误后依次打开电台和基准站的电源。
二、仪器的连接与设置
1、打开
1、新建任务（如20160309），选择西安80坐标系统；
2、保存任务；
3、打开新建的任务20160309；
4、在文件中查看任务属性、当前坐标参数（取消“水平平差、垂直平差”的“√”；
5、在配置下找到手薄端口设置，打开选择蓝牙连接，先绑定基准站（＃＃＃＃＃＃61）；
6、测量下打开开启基准站接收机，进入界面后，在右下角点击断开；返回后在测量下再一次打开开启基准站接收机进行设置，输入点号(如1），用卷尺测量地面到基准站蘑菇头下沿的高度，在天线高度一栏填写测量的高度（如1.60），选择天线底部，然后点击“此处”，然后点击下一步（不用修改如何设置），在然后确定，完成基准站连接；
7、在配置下找到手薄端口设置，打开选择蓝牙连接，绑定移动站（＃＃＃＃＃＃41）；
8、测量下打开开启移动站接收机，进入界面后，在右下角点击断开；返回后在
测量下再一次打开开启移动站接收机进行设置，按电台上面最上面的按钮打开通道，在手薄上选择的通道和电台打开的通道保持一致，然后下一步、下一步，完成移动站的连接。
三、点校正
1、在测量下打开测量点界面（地形点）将已知点的两点坐标进行测量（如A1、A2），在测量之前观察界面中的天线高度与移动站的天线高度是否保持一致，如果不一致就先将其调整成一致在进行测量；在键入下键入已知点坐标X、Y、H（注意将点号与原来测量的点号区分开，如JA1、JA2）；
2、在测量下最后一行找到“点校正”，打开点校正，点击左下角的增加，进入界面后点击第一行“...”，选择A1，再点击第三行”...”，选择JA1，点击右下角的确定，再选择增加，进入界面后点击第一行“...”，选择A2，再点击第三行”...”，选择JA2，然后点击“计算”，计算后选择确定、是，返回主界面；
3、在测量下打开测量点界面，测量（注意区分点号如A01）已知点A1或者A2,然后在文件下找到点管理器，打开点管理器，查看A01坐标与已知点A1坐标进行比较，点校正完成。
四、注意事项
1、测量完成后收拾仪器时，先将基准站、移动站、电台关机，再拔下电源线；
2、收拾仪器时检查是否将所有部件装箱；
3、测量回来后将仪器的电池进行充电，将有电的电池不要装在仪器内；
4、及时将数据在手薄上导出。