螺丝标准,中英文对照表
螺栓标准件中英文对照表
DIN471
轴用弹性垫圈
Retaining rings for shafts(external),circlips
GB893-86
50
DIN472
孔用弹性垫圈
Retaining rings for bores(internal),circlips
GB893.86
51
DIN478
方头带垫螺栓
Square head bolts with collar
序号
Item
德国标准
DIN-Standard
中文品名
英文品名
Desciption in English
国际标准
ISO-Standard
中国标准
GB-Standard
69
DIN601
六角头螺栓
Hexagon blots
ISO4016
70
DIN603
大半圆头方颈螺栓（马车螺栓）
Mushroom head square neck bolts(carriage bolts)
I-sections
GB852-88
35
DIN436
方垫圈
Square washers
36
DIN438
开槽凹端紧定螺钉
Slotted set with cup point
ISO7436
GB74-85
37
DIN439
六角薄螺母
Hexagon thin nuts
ISO4035
GB6172-86
38
DIN439
Slotted knurled thumb screws with collar
46
DIN466
螺丝名称的中英文对照表
螺丝名称的中英文对照表The final revision was on November 23, 2020螺丝名称的中英文对照表常用英文单词及简写形式No. 单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread P T 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标47 ISO / 国际标准48 NFE / 法标49 GB / 国家标准50 Quality / 质量51 surface hardness 表面硬度52 product treatment 表面处理53 plating 电镀54 heat 热55 Screws And Shafts For Motorcycle Or Bicycle 机(踏)车用螺丝、轴心56 Screws And Shafts For Sewing Maching 针车用螺丝、轴心57 Socket Set Screws 止付螺丝58 Stainless Steel Coarse Thread Screws 不锈钢宽牙螺丝59 Stainless Steel High-Low Thread Screws 不锈钢高低牙螺丝60 Stainless Steel Machine Screws 不锈钢机械螺丝61 Stainless Steel Self Drilling Screws 不锈钢钻尾螺丝62 Stainless Steel Self Tapping Screws 不锈钢螺丝 class=a1>自攻螺丝63 Stainless Steel Thread Cutting Screws 不锈钢自削螺丝64 Stainless Steel Tri-Lobular Thread Screws 不锈钢三角牙螺丝65 Steel Ceiling Anchors 插片壁虎66 Drop in Anchors 内迫壁虎67 Steel Hit Anchors 碳钢锤钉壁虎68 Steel Hex Coupling Nuts 碳钢六角螺帽69 Wedge Anchors 强力车修壁虎70 Cut Anchors 外迫壁虎71 Chemical Anchors 化学壁虎72 Heavy Duty Expansion Anchors 不锈钢重载胀栓73 Tie Wire Anchors 鱼眼壁虎?企眼长螺帽74 Hammer Drive Anchors 锌合金打入式壁虎75 Strut Nuts 弹簧螺帽?76 Toggle Bolts (Spring Toggle & Gravity Toggle) 兰花夹系列77Nylon Frame Anchors or Metalframe Anchors 门窗、地板专用壁虎78 Hollow Wall Anchors 石膏板中空壁虎79 Sleeve Anchors 套管式壁虎80 Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors) 打入式壁虎鱼形尼龙壁虎81 Hit Anchors 强力式锤钉壁虎82 Bolt Anchors 电梯壁虎83 Heavy duty anchors 重载壁虎84 Loxin Masonry Anchors 两片夹85 Set Bolts 定位螺栓86 Short Strap Anchors 长型兰花夹87 Drop in Setting Tools 工具棒88 Elephant foot anchors 象脚壁虎89 Concrete Insert 水泥预埋件90 Drop in Anchor with Lip 翻边胀轴91 Legs Drywall Anchors 冲件92 Hex Cap Nuts 六角盖头螺帽93 Hex Serrated Nuts 六角锯齿螺帽?94 Hex Flange Nuts 六角轮缘螺帽?95 Hex Coupling Nuts(High Nuts) 高脚螺帽96 Round Nuts 圆螺帽97 Square Nuts 四角螺帽98 Pipe Nuts 管用螺帽99 Wheel Nuts 轮壳螺帽100 Wing Nuts 蝶型螺帽101 U Nuts U形螺帽?102 T Nuts T形螺帽103 Eye Nuts 环首螺帽104 Kep Nuts 齿形螺帽?105 Clinch Nuts 齿花螺帽106 Corten Steel Heavy Hex Nuts 耐候钢六角重型螺帽107 Weld Nuts 焊接螺帽108 Heigh Strength Nuts 高张力螺帽109 Structural Nuts 建业用螺帽110 Stainless Steel Nuts 不锈钢螺帽111 Brass Nuts 铜螺帽112 Aluminum Nuts 铝螺帽113 Alloy Steel Nuts 合金钢螺帽114 Heavy Duty Wheel Hub Nuts 重型车螺帽115 Acorn Cap Nuts 铁器焊接袋帽116 All-Metal Prevailing Torque Type Nuts 金属预置扭矩式螺帽117 Anchor Nuts 壁虎螺帽118 Big Size Nuts 大尺寸螺帽119 Closed End Acorn Nuts 铁盖袋帽120 Conical Washer Nuts 盘形华司螺帽121 Din 986 Domed Cap Nuts 铁盖+尼龙圈组合盖帽122 Flange Nylon Insert Lock Nuts 突缘尼龙盖帽123 Flat Waser Nuts 平面华司螺帽124 Hex Slotted Nut 六角割沟螺帽125 Self-Locking Nuts 自锁螺帽126 Sliding Nuts 制止螺帽127 Sln Self-Locking Nuts Sln-自动防松螺帽128 Special Nuts 其它特殊螺帽129 Spring Nuts 弹簧螺帽130 Stainless Steel Flange Nuts 不锈钢突缘螺帽131 Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角轮缘尼龙螺帽132 Stainless Steel Heavy Hex Nuts 不锈钢六角重型螺帽133 Stainless Steel Hex Nuts 不锈钢六角螺帽134 Stainless Steel Nylon Insert Lock Nuts 不锈钢尼龙嵌入螺帽135 Hex Nuts 普通六角螺帽136 Heavy Hex Nuts 六角重型螺帽137 Hex Jam Nuts 薄型螺帽138 Nylon Insert Lock Nuts 尼龙嵌入防松螺帽139 Hex Machine Screw Nut 机械螺丝用六角螺帽140 Hex Head Cap Screws(Hex Bolts) 六角螺丝(栓)141 Hex Head Machine Bolts 六角机械螺丝142 Hex Lag Bolts 六角木牙螺丝143 Square Head Bolts 四角螺丝144 Carriage Bolts 马车。
紧固件英语翻译及螺丝标准件英语对照大全
B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝) B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝) C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金5052d. Brass: 黄铜e. Bronze: 青铜f. UNS C11000 Copper: 锑铜Finish Code: 外观处理规格Head Code: 头部外型螺丝型号Drive Code: 头部剖沟,特征型号Length Code: 螺丝长度(mm)A-1: Thread Code: 螺丝型号A-2: Length Code: 螺丝长度:A-3: Drive Code/ 头部剖沟,特征.a. Slotted: 一字( Minus )b. Phillips: 十字( Plus )c. Phil-Slot: 一字/十字d. Hex Scoket: 内六角e. One Way: 单向(只可锁入,不可退出)A-4: Head Code/ 头部外型.a. Flat: 平头(锁入后,顶部与工作件齐平)b. Oval: 色拉头c. Round: 圆头d. Pan: 圆扁头e. Truss: 大圆扁头f. Hex : 六角头A-5: Finish Code/ 外观处理.a. Z: Zine-Plated: 镀锌b. Ni: Ni-Plated: 镀镍c. Tin-Plated: 镀锡d. Zine Plated / Green Iridite: 镀锌绿膜处理.e. Radiant Plated: 镀五彩f. Passivate: 抗氧化处理.g. Alodial Finish: 无外观处理螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度各类紧固件标准件产品英语翻译对照插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力车修壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors 鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors) 强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts 普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角木牙螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts马车螺丝Carriage Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws旋入螺丝Drive Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts突缘螺丝Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems)大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铜螺丝Brass Screws铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts 拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt车辆(汽车)螺丝、螺帽Automotive Fasteners航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control Bolts拉栓Blind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws 不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws 铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws 其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging 自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace 连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace 中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives成型冲模Header Punches In Various Drives螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass)螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine 止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉Spheroidizing Bright Annealing Furnace 球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd 电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage 螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers 螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod马达轴承轴心组件Bearing Shaft(Motor)轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind Nuts拉钉Blind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动拉钉钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet Metal Fasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle 针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-Low Thread Screws不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws。
螺丝标准 中英文对照表
ISO7090
平垫
plain washers
ISO7091
spring lock
重型弹垫
washers,tang
ends
spring lock
标准弹垫
washers,square
ends
鞍形弹垫
single coil spring lock washers
弹簧止动垫圈
curved spring washers
六角头精配螺栓（短 螺纹）
hexagon fitted bolts,short thread
77
DIN653
滚花平头螺钉
knurled thumb screws thin type
78
DIN660
半圆头铆钉
round head rivets
79
DIN661
沉头铆钉
contersunk head rivets
section
square taper
34
DIN435
方斜垫圈(I型)
washers for I-
sections
35
DIN436
方垫圈
square washers
36
DIN438
开槽凹端紧定螺钉
slotted set with cup point
37
DIN439
六角薄螺母
hexagon thin nuts
hexagon socket
93
DIN913 内六角平端紧定螺钉 set screws with
flat point
hexagon socket
94
DIN914 内六角尖端紧定螺钉 set screws with
螺丝类型中英文对照
螺丝类型中英文对照六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS) 六角机械螺丝 HEX HEAD MACHINE BOLTS六角木牙螺丝 HEX LAG BOLTS四角螺丝 SQUARE HEAD BOLTST头螺丝 T HEAD BOLTS马车螺丝CARRIAGE BOLTS环首螺丝EYE BOLTS内六角孔螺丝HEX SOCKET CAP SCREWS固定螺丝SET SCREWS螺椿栓STUD BOLTS螺旋椿SCREW STUDS轮壳螺栓WHEEL BOLTS翼形螺丝WING SCREWS自攻螺丝SELF TAPPING SCREWS自削螺丝THREAD CUTTING SCREWS钻尾螺丝SELF DRILLING SCREWS旋入螺丝DRIVE SCREWS机械螺丝MACHINE SCREWS木螺丝WOOD SCREWS家具螺丝FURNITURE SCREWS塑板螺丝CHIPBOARD SCREWS墙用螺丝DRYWALL SCREWS基础螺栓FOUNDATION BOLTSU型螺栓U BOLTS勾头螺栓HOOK BOLTS套挂螺丝TOGGLE BOLTS突缘螺丝FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS耐候钢螺丝 CORTEN STEEL HEAVY HEX BOLTS扭矩控制螺栓T.C.BOLTS高张力螺栓HIGH STRENGTH BOLTS剪力钉(焊接螺丝) WELDING STUDS螺丝附华司组合SCREWS AND WASHERS ASSEMBLED(SEMS) 大尺寸螺栓BIG SIZE BOLTS不锈钢小螺丝STAINLESS STEEL SHEET METAL SCREWS 不锈钢大螺丝STAINLESS STEEL BOLTS铜螺丝BRASS SCREWS铝螺丝ALUMINUM SCREWS合金钢螺丝ALLOY STEEL SCREWS电子螺丝ELECTRONIC SCREWS微小精密螺丝MICRO SCREWS塑胶螺丝PLASTIC SCREWS复合材料用螺丝PARTICLE BOARD SCREWS钛合金螺丝TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料TI,ZR,MO,NB PARE METAL BOLTS PARTS 拇指螺丝THUMB SCREWS双头牙螺丝DOUBLE END SCREWS HANGER BOLT车辆(汽车)螺丝、螺帽AUTOMOTIVE FAS TENERS航太用螺丝AEROSPACE FAS TENERS飞机特殊扣件SOURCE CONTROL BOLTS拉栓BLIND BOLTS面板螺丝PANEL FAS TENERS电梯螺丝ELEVATOR BOLTS四角头固定螺丝SQUARE SET SCREWS大头马车螺丝STEP BOLTS单向螺丝ONE WAY LAG SCREWS管夹螺丝HOSE CLAMP SCREWS不锈钢固定螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝HINGE SCREWS货柜螺丝CONTAINER SCREWS复合材料钻尾螺丝BI-METAL SELF DRILLING SCREWS三角牙螺丝TRILOBULAR THREAD SCREWS高低牙螺丝HIGH LOW SCREWS夹板用螺丝PARTICLE BOARD SCREWS马桶螺丝TOILET CLOSET BOLTS特长螺丝SPECIAL LONGER SCREWS建业螺丝BUILDING FASTENERS不锈钢六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS其它特殊螺丝SPECIAL SCREWS OR BOLTS不锈钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS宽牙螺丝（粗牙螺丝）COARSE THREAD SCREWS链带螺丝COLLATED SCREWS水泥螺丝CONCRETE SCREWS板模螺丝CONSTRUCTION BOLTS涞□萁z DIE CAST WING SCREWS; ZINC ALLOY重型车螺丝HEAVY DUTY WHEEL HUB BOLTS内六角固定螺丝HEX SOCKET SET SCREWS复合材料用螺丝（夹板用）PARTICLE BOARD SCREWS犁壁螺丝PLOW BOLTS机(踏)车用螺丝、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺丝、轴心SCREWS AND SHAFTS FOR SEWING MACHING止付螺丝SOCKET SET SCREWS不锈钢宽牙螺丝STAINLESS STEEL COARSE THREAD SCREWS不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS不锈钢三角牙螺丝TAINLESS STEEL TRI-LOBULAR THREAD SCREWS 不锈钢木螺丝STAINLESS STEEL WOOD SCREWS套挂螺栓及螺丝OGGLE BOLTS钛合金膨胀螺丝TITANIUM ALLOY EXPANSION BOLTS。
螺栓螺母型号及尺寸规格表中英文对照
螺栓螺母型号及尺寸规格表中英文对照
螺栓螺母型号及尺寸规格表中英文对照
螺栓螺母是经常被使用在机械设备中，也是很多工程设计系统中常见的一种零部件。
它通常用于将两个组件紧固在一起，以便紧固机械设备。
为了使用户在选购螺栓螺母时能够更准确地选取到正确的尺寸型号，下面将介绍螺栓螺母型号及尺寸规格英文表：
螺栓类型：
Hex Head Bolt - 六角头扣件
Flat Washer - 平垫片
Carriage Bolt - 马车螺栓
Socket Head Cap Screw - 套筒头螺丝
Socket Head Bolt - 套筒头螺栓
Locknut - 块状螺母
螺母类型：
Hex nut - 六角螺母
Nylon Nut - 尼龙螺母
Square Nut - 方形螺母
Plain Washer - 平垫圈
Star Lock Washer -星形锁紧垫圈
Wing Nut - 可转把螺母
上文已经介绍了常见的螺栓螺母的型号及尺寸规格表中的英文对照，从而使消费者可以更为准确的选择符合自己应用需求的恰当型号和尺寸的螺栓螺母。
从而不仅能够减少消费者的购买成本，同时也能够有效提升产品的使用效率和使用寿命，从而为客户提供更加优质的服务。
螺丝标准及中英文对照
‘M/M机械螺丝规格表2006-10-30 10:11:41环首螺帽EYE NUTS齿形螺帽KEP NUTS齿花螺帽CLINCH NUTS普通六角螺帽HEX NUTS六角重型螺帽HEAVY HEX NUTS薄型螺帽HEX JAM NUTS焊接螺帽WELD NUTS高张力螺帽HEIGH STRENGTH NUTS建业用螺帽STRUCTURAL NUTS不锈钢螺帽STAINLESS STEEL NUTS铜螺帽BRASS NUTS铝螺帽ALUMINUM NUTS合金钢螺帽ALLOY STEEL NUTS重型车螺帽HEAVY DUTY WHEEL HUB NUTS铁器焊接袋帽ACORN CAP NUTS金属预置扭矩式螺帽ALL-METAL PREVAILING TORQUE TYPE NUTS 耐候钢六角重型螺帽CORTEN STEEL HEAVY HEX NUTS铁盖+尼龙圈组合盖帽DIN 986 DOMED CAP NUTS突缘尼龙盖帽FLANGE NYLON INSERT LOCK NUTS不锈钢突缘螺帽STAINLESS STEEL FLANGE NUTS不锈钢六角轮缘尼龙螺帽STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS 不锈钢六角重型螺帽STAINLESS STEEL HEAVY HEX NUTS不锈钢六角螺帽STAINLESS STEEL HEX NUTS不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS机械螺丝用六角螺帽HEX MACHINE SCREW NUT圆螺帽ROUND NUTS四角螺帽SQUARE NUTS管用螺帽PIPE NUTS轮壳螺帽WHEEL NUTS壁虎螺帽ANCHOR NUTS大尺寸螺帽BIG SIZE NUTS平面华司螺帽FLAT WASER NUTS六角割沟螺帽HEX SLOTTED NUT自锁螺帽SELF-LOCKING NUTS制止螺帽SLIDING NUTSSLN-自动防松螺帽SLN SELF-LOCKING NUTS其它特殊螺帽SPECIAL NUTS弹簧螺帽SPRING NUTS铁盖袋帽CLOSED END ACORN NUTS盘形华司螺帽CONICAL WASHER NUTS六角盖头螺帽HEX CAP NUTS六角锯齿螺帽HEX SERRATED NUTS六角轮缘螺帽HEX FLANGE NUTS高脚螺帽HEX COUPLING NUTS(HIGH NUTS)蝶型螺帽WING NUTSU形螺帽U NUTST形螺帽T NUTS。
螺丝名称的中英文对照表
螺丝名称的中英文对照表常用英文单词及简写形式No. 单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread P T 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标47 ISO / 国际标准48 NFE / 法标49 GB / 国家标准50 Quality / 质量51 surface hardness 表面硬度52 product treatment 表面处理53 plating 电镀54 heat 热55 Screws And Shafts For Motorcycle Or Bicycle 机(踏)车用螺丝、轴心56 Screws And Shafts For Sewing Maching 针车用螺丝、轴心57 Socket Set Screws 止付螺丝58 Stainless Steel Coarse Thread Screws 不锈钢宽牙螺丝59 Stainless Steel High-Low Thread Screws 不锈钢高低牙螺丝60 Stainless Steel Machine Screws 不锈钢机械螺丝61 Stainless Steel Self Drilling Screws 不锈钢钻尾螺丝62 Stainless Steel Self Tapping Screws 不锈钢螺丝class=a1>自攻螺丝63 Stainless Steel Thread Cutting Screws 不锈钢自削螺丝64 Stainless Steel Tri-Lobular Thread Screws 不锈钢三角牙螺丝65 Steel Ceiling Anchors 插片壁虎66 Drop in Anchors 内迫壁虎67 Steel Hit Anchors 碳钢锤钉壁虎68 Steel Hex Coupling Nuts 碳钢六角螺帽69 Wedge Anchors 强力车修壁虎70 Cut Anchors 外迫壁虎71 Chemical Anchors 化学壁虎72 Heavy Duty Expansion Anchors 不锈钢重载胀栓73 Tie Wire Anchors 鱼眼壁虎企眼长螺帽74 Hammer Drive Anchors 锌合金打入式壁虎75 Strut Nuts 弹簧螺帽76 Toggle Bolts (Spring Toggle & Gravity Toggle) 兰花夹系列77 Nylon Frame Anchors or Metalframe Anchors 门窗、地板专用壁虎78 Hollow Wall Anchors 石膏板中空壁虎79 Sleeve Anchors 套管式壁虎80 Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors) 打入式壁虎鱼形尼龙壁虎81 Hit Anchors 强力式锤钉壁虎82 Bolt Anchors 电梯壁虎83 Heavy duty anchors 重载壁虎84 Loxin Masonry Anchors 两片夹85 Set Bolts 定位螺栓86 Short Strap Anchors 长型兰花夹87 Drop in Setting Tools 工具棒88 Elephant foot anchors 象脚壁虎89 Concrete Insert 水泥预埋件90 Drop in Anchor with Lip 翻边胀轴91 Legs Drywall Anchors 冲件92 Hex Cap Nuts 六角盖头螺帽93 Hex Serrated Nuts 六角锯齿螺帽94 Hex Flange Nuts 六角轮缘螺帽95 Hex Coupling Nuts(High Nuts) 高脚螺帽96 Round Nuts 圆螺帽97 Square Nuts 四角螺帽98 Pipe Nuts 管用螺帽99 Wheel Nuts 轮壳螺帽100 Wing Nuts 蝶型螺帽101 U Nuts U形螺帽102 T Nuts T形螺帽103 Eye Nuts 环首螺帽104 Kep Nuts 齿形螺帽105 Clinch Nuts 齿花螺帽106 Corten Steel Heavy Hex Nuts 耐候钢六角重型螺帽107 Weld Nuts 焊接螺帽108 Heigh Strength Nuts 高张力螺帽109 Structural Nuts 建业用螺帽110 Stainless Steel Nuts 不锈钢螺帽111 Brass Nuts 铜螺帽112 Aluminum Nuts 铝螺帽113 Alloy Steel Nuts 合金钢螺帽114 Heavy Duty Wheel Hub Nuts 重型车螺帽115 Acorn Cap Nuts 铁器焊接袋帽116 All-Metal Prevailing Torque Type Nuts 金属预置扭矩式螺帽117 Anchor Nuts 壁虎螺帽118 Big Size Nuts 大尺寸螺帽119 Closed End Acorn Nuts 铁盖袋帽120 Conical Washer Nuts 盘形华司螺帽121 Din 986 Domed Cap Nuts 铁盖+尼龙圈组合盖帽122 Flange Nylon Insert Lock Nuts 突缘尼龙盖帽123 Flat Waser Nuts 平面华司螺帽124 Hex Slotted Nut 六角割沟螺帽125 Self-Locking Nuts 自锁螺帽126 Sliding Nuts 制止螺帽127 Sln Self-Locking Nuts Sln-自动防松螺帽128 Special Nuts 其它特殊螺帽129 Spring Nuts 弹簧螺帽130 Stainless Steel Flange Nuts 不锈钢突缘螺帽131 Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角轮缘尼龙螺帽132 Stainless Steel Heavy Hex Nuts 不锈钢六角重型螺帽133 Stainless Steel Hex Nuts 不锈钢六角螺帽134 Stainless Steel Nylon Insert Lock Nuts 不锈钢尼龙嵌入螺帽135 Hex Nuts 普通六角螺帽136 Heavy Hex Nuts 六角重型螺帽137 Hex Jam Nuts 薄型螺帽138 Nylon Insert Lock Nuts 尼龙嵌入防松螺帽139 Hex Machine Screw Nut 机械螺丝用六角螺帽140 Hex Head Cap Screws(Hex Bolts) 六角螺丝(栓)141 Hex Head Machine Bolts 六角机械螺丝142 Hex Lag Bolts 六角木牙螺丝143 Square Head Bolts 四角螺丝144 Carriage Bolts 马车。
紧固件螺丝中英文对照
紧固件螺丝中英文对照标签：紧固件螺丝中英文对照上一篇：分享下一篇：[转贴]推陈出新《变形金刚》《GB/T 8-1988 方头螺栓 C 级 Square head bolts--Product grade C3 GB/T 10-1988 沉头方颈螺栓 Flat countersunk square neck bolts4 GB/T 11-1988 沉头带榫螺栓 Flat countersunk nib bolts5 GB/T 12-1988 半圆头方颈螺栓 Cup head square neck bolts6 GB/T 13-1988 半圆头带榫螺栓 Cup head nib bolts7 GB/T 15-1988 大半圆头带榫螺栓 Cup head nib bolts with large head8 GB/T 22-1976 小六角头导颈螺栓 Bolts, small hexagon head with fit neck9 GB/T 23-1976 小六角头螺杆带孔螺栓 Bolts, small hexagon head with hole through the shank10 GB/T 24-1976 小六角头螺杆带孔导颈螺栓 Bolts, small hexagon head with fit neck and hole through the shank11 GB/T 25-1976 小六角头头部带孔螺栓 Bolts, small hexagon head with holes through the head12 GB/T 26-1976 小六角头头部带孔导颈螺栓 Bolts, small hexagon head with fit neck and holes through the head13 GB/T 27-1988 六角头铰制孔用螺栓 A 和 B 级 Hexagon fit bolts--Product grade A and B14 GB/T 28-1988 六角头螺杆带孔铰制孔用螺栓 A 和 B 级 Hexagon fit bolts with Split pin hole on shank--Product grade A and B15 GB/T 29.1-1988 六角头头部带槽螺栓 A 和 B 级 Hexagon bolts with slot on head--Product grade A and B16 GB/T 29.2-1988 十字槽凹穴六角头螺栓 Cross recessed hexagon bolts with indentation17 GB/T 31.1-1988 六角头螺杆带孔螺栓 A 和 B 级 Hexagon bolts with split pin hole on shank--Product grade A and B18 GB/T 31.2-1988 六角头螺杆带孔螺栓细杆 B 级 Hexagon bolts with split pin hole on shank--Reduced shank--Product grade B19 GB/T 31.3-1988 六角头螺杆带孔螺栓细牙 A 和 B 级 Hexagon bolts with split pin hole on shank--Fine pitch thread--Product grade A and B20 GB/T 32.1-1988 六角头头部带孔螺栓 A 和 B 级 Hexagon bolts with wire holes on head--Product grade A and B 21 GB/T 32.2-1988 六角头头部带孔螺栓细杆 B 级 Hexagon bolts with wire holes on head--Reducedshank--Product grade B22 GB/T 32.3-1988 六角头头部带孔螺栓细牙 A 和 B 级 Hexagon bolts with wire holes on head--Fine pitch thread--Product grade A and B23 GB/T 35-1988 小方头螺栓 B 级 Square head bolts with smallhead--Product grade B24 GB/T 37-1988 T 型槽用螺栓 Bolts for T-Slot26 GB/T 39-1988 方螺母 C 级 Square nuts--Product grade C27 GB/T 41-1986 1 型六角螺母 C 级 Hexagon nuts--Style 1--Product grad C28 GB/T 56-1988 六角厚螺母 Hexagon thick nuts30 GB/T 62-1988 蝶形螺母 Wing nuts31 GB/T 63-1988 环形螺母 Lifting nuts32 GB/T 65-1985 开槽圆柱头螺钉 Slotted cheese head screws33 GB/T 67-1985 开槽盘头螺钉 Slotted pan head screws34 GB/T 68-1985 开槽沉头螺钉 Slotted countersunk head screws35 GB/T 69-1985 开槽半沉头螺钉 Slotted raised countersunk head screws36 GB/T 70-1985 内六角圆柱头螺钉 Hexagon socket cap head screws37 GB/T 71-1985 开槽锥端紧定螺钉 Slotted set screws with cone point38 GB/T 72-1988 开槽锥端定位螺钉 Slotted set screws with cone point39 GB/T 73-1985 开槽平端紧定螺钉 Slotted set screws with flat point40 GB/T 74-1985 开槽凹端紧定螺钉 Slotted set screws with cup point41 GB/T 75-1985 开槽长圆柱端紧定螺钉 Slotted set screws withlong dog point42 GB/T 77-1985 内六角平端紧定螺钉 Hexagon socket set screws with flat point43 GB/T 78-1985 内六角锥端紧定螺钉 Hexagon socket set screws with cone point44 GB/T 79-1985 内六角圆柱端紧定螺钉 Hexagon socket set screws with dog point45 GB/T 80-1985 内六角凹端紧定螺钉 Hexagon socket set screws with cup point46 GB/T 83-1988 方头长圆柱球面端紧定螺钉 Square set screws with long dog point and rounded end47 GB/T 84-1988 方头凹端紧定螺钉 Square set screws with cup point48 GB/T 85-1988 方头长圆柱端紧定螺钉 Square set screws with long dog point49 GB/T 86-1988 方头短圆柱锥端紧定螺钉 Square set screws with short dog point and cone end52 GB/T 91-1986 开口销 Split pins53 GB/T 93-1987 标准型弹簧垫圈 Single coil spring lock washers--Normal type57 GB/T 95-1985 平垫圈 -C 级 Plain washers--Product grade C90 GB/T 794-1993 加强半圆头方颈螺栓 Strengthened cap head square neck bolts91 GB/T 798-1988 活节螺栓 Eye bolts92 GB/T 799-1988 地脚螺栓 Eyelet bolts93 GB/T 800-1988 沉头双榫螺栓 Flat countersunk double nib bolts94 GB/T 802-1988 组合式盖形螺母 Acorn nuts95 GB/T 804-1988 球面六角螺母 Hexagon nuts with raised face96 GB/T 805-1988 扣紧螺母 Tight nuts97 GB/T 806-1988 滚花高螺母 Knurled nut with collar98 GB/T 807-1988 滚花薄螺母 Knurled nuts99 GB/T 808-1988 小六角特扁细牙螺母 Small hexagon thin nuts-Fine pitch thread100 GB/T 809-1988 嵌装圆螺母 Insert round nuts101 GB/T 810-1988 小圆螺母 Small round nuts102 GB/T 812-1988 圆螺母 Round nuts103 GB/T 815-1988 端面带孔圆螺母 Round nuts with drilled holes in one face104 GB/T 816-1988 侧面带孔圆螺母 Round nuts with set pin holes in side 105 GB/T 817-1988 带槽圆螺母 Slotted round nuts106 GB/T 818-1985 十字槽盘头螺钉 Cross recessed pan head screws107 GB/T 819-1985 十字槽沉头螺钉 Cross recessed countersunk head screws 108 GB/T 820-1985 十字槽半沉头螺钉 Cross recessed raised countersunk head screws109 GB/T 821-1988 方头倒角端紧定螺钉 Square set screws with chamfered end110 GB/T 822-1988 十字槽圆柱头螺钉 Cross recessed cheese head serews 111 GB/T 823-1988 十字槽小盘头螺钉 Cross recessed small pan head screws 112 GB/T 824-1976 圆柱头内花键螺钉 Screws,fluted socket head113 GB/T 825-1988 吊环螺钉 Eyebolts114 GB/T 827-1986 标牌铆钉 Rivets for name plate115 GB/T 828-1988 开槽盘头定位螺钉 Slotted pan head set setscrews with dog point116 GB/T 829-1988 开槽圆柱端定位螺钉 Slotted setscrews with dog point 117 GB/T 830-1988 开槽圆柱头轴位螺钉 Slotted cheese head screws with shoulder118 GB/T 831-1988 开槽无头轴位螺钉 Slotted shoulder screws119 GB/T 832-1988 开槽带孔球面圆柱头螺钉 Slotted capstan screws120 GB/T 833-1988 开槽大圆柱头螺钉 Slotted large cheese head screws 121 GB/T 834-1988 滚花高头螺钉 Knurled thumb screws122 GB/T 835-1988 滚花平头螺钉 Knurled screws123 GB/T 836-1988 滚花小头螺钉 Knurled screws with small head124 GB/T 837-1988 开槽盘头不脱出螺钉 Slotted pan head screws with waisted shank125 GB/T 838-1988 六角头不脱出螺钉 Hexagon screws with waisted shank 126 GB/T 839-1988 滚花头不脱出螺钉 Knurled thumb screws with waisted shank127 GB/T 840-1988 塑料滚花头螺钉 Plastic diamond knurlhead screws128 GB/T 845-1985 十字槽盘头自攻螺钉 Cross recessed pan head tapping screws129 GB/T 846-1985 十字槽沉头自攻螺钉 Cross recessed countersunk head tapping screws130 GB/T 847-1985 十字槽半沉头自攻螺钉 Cross recessed raised countersunk head tapping screws131 GB/T 848-1985 小垫圈 --A 级 Plain washers--Small series--Productgrade A132 GB/T 849-1988 球面垫圈 Weshers with ball face133 GB/T 850-1988 锥面垫圈 Washers with cone face134 GB/T 851-1988 开口垫圈 Washers with split135 GB/T 852-1988 工字钢用方斜垫圈 Square taper washers for I section 136 GB/T 853-1988 槽钢用方斜垫圈 Square taper washers for slot section 137 GB/T 854-1988 单耳止动垫圈 Tab washers with long tab138 GB/T 855-1988 双耳止动垫圈 Tab washers with long tab and wing139 GB/T 856-1988 外舌止动垫圈 External tab washers140 GB/T 858-1988 圆螺母用止动垫圈 Tab washers for round nut141 GB/T 859-1987 轻型弹簧垫圈 Single coil spring lock washers,Light type142 GB/T 860-1987 鞍形弹性垫圈 Curved spring washers143 GB/T 861.1-1987 内齿锁紧垫圈 Lock washers internal teeth144 GB/T 861.2-1987 内锯齿锁紧垫圈 Serrated lock washers internal teeth 145 GB/T 862.1-1987 外齿锁紧垫圈 Lock washers external teeth146 GB/T 862.2-1987 外锯齿锁紧垫圈 Serrated lock washers external teeth 147 GB/T 863.1-1986 半圆头铆钉 ( 粗制 ) Round head rivets--Black148 GB/T 863.2-1986 小半圆头铆钉 ( 粗制 ) Round head rivets with small head--Black149 GB/T 864-1986 平锥头铆钉 ( 粗制 ) Cone head rivets--Black150 GB/T 865-1986 沉头铆钉 ( 粗制 ) Countersunk head rivets-Black 151 GB/T 866-1986 半沉头铆钉 ( 粗制 ) Oval countersunk head rivets--Black 152 GB/T 867-1986 半圆头铆钉 Round head rivets153 GB/T 868-1986 平锥头铆钉 Cone head rivets154 GB/T 869-1986 沉头铆钉 Countersunk head rivets155 GB/T 870-1986 半沉头铆钉 Oval countersunk head rivets156 GB/T 871-1986 扁圆头铆钉 Flat round head rivets157 GB/T 872-1986 扁平头铆钉 Thin head rivets158 GB/T 873-1986 扁圆头半空心铆钉 Oval head semi-tubular rivets159 GB/T 874-1986 120° 沉头半空心铆钉 120 degree countersunk head semi-tubular rivets160 GB/T 875-1986 偏平头半空心铆钉 Thin head semi-tubular rivet161 GB/T 876-1986 空心铆钉 Tubular rivets162 GB/T 877-1986 开尾圆锥销 Taper pins with split163 GB/T 878-1986 螺纹圆柱销 Parallel pins with external thread164 GB/T 879-1986 弹性圆柱销 Spring-type straight pins—Slotted165 GB/T 880-1986 带孔销 Pins with split pin hole166 GB/T 881-1986 螺尾锥销 Taper pins with external thread167 GB/T 882-1986 销轴 Clevis pins with head168 GB/T 883-1986 锥销锁紧挡圈 Lock rings with cone pin169 GB/T 884-1986 螺钉锁紧挡圈 Lock ring with screw170 GB/T 885-1986 带锁圈的螺钉锁紧挡圈 Lock rings with screw and circlip 171 GB/T 886-1986 轴肩挡圈 Rings for shoulder172 GB/T 889-1986 1 型非金属嵌件六角锁紧螺母 Prevailing torque type hexagon nuts (with non-metallic insert),style 1173 GB/T 891-1986 螺钉紧固轴端挡圈 Lock rings at the end of shaft with screw174 GB/T 892-1986 螺栓紧固轴端挡圈 Lock rings at the end of shaft with bolt175 GB/T 893.1-1986 孔用弹性挡圈 --A 型 Circlips for holes--Type A 176 GB/T 893.2-1986 孔用弹性挡圈 --B 型 Circlips for hole--Type B177 GB/T 894.1-1986 轴用弹性挡圈 --A 型 Circlips for shaft--Type A 178 GB/T 894.2-1986 轴用弹性挡圈 --B 型 Circlips for shaft--Type B 179 GB/T 895.1-1986 孔用钢丝挡圈 Roundwire snap rings for hole180 GB/T 895.2-1986 轴用钢丝挡圈 Roundwire snap rings for shaft 181 GB/T 896-1986 开口挡圈 "E" rings182 GB/T 897-1988 双头螺柱 bm=1d Double end studs--bm=1d183 GB/T 898-1988 双头螺柱 bm=1.25d Double end studs bm=1.25d184 GB/T 899-1988 双头螺柱 bm=1.5d Double end studs bm=1.5d185 GB/T 900-1988 双头螺柱 bm=2d Double end studs bm=2d186 GB/T 901-1988 等长双头螺柱 B 级 Double end studs (clampingtype)--Product grade B187 GB/T 902.1-1989 手工焊用焊接螺柱 Weld studs for manual welding 188 GB/T 902.2-1989 机动弧焊用焊接螺柱 Weld studs for arc welding189 GB/T 902.3-1989 储能焊用焊接螺柱 Weld studs for capacitor discharge welding190 GB/T 921-1986 钢丝锁圈 Round wire circlips191 GB/T 922-1986 木螺钉技术条件 Specifications for wood screws192 GB/T 923-1988 盖形螺母 Acorn nuts193 GB/T 925-1988 轻型六角自锁螺母 Self-locking nuts,hexagon light 194 GB/T 927-1988 球面六角自锁螺母 Self-locking nuts,hexagon sphere 195 GB/T 929-1988 单耳托板自锁螺母 Self-locking nuts,singlelug, anchor 196 GB/T 930-1988 双耳托板自锁螺母 Self-locking nuts,twolug, anchor 197 GB/T 931-1988 角形托板自锁螺母 Self-locking nuts,angle, anchor 198 GB/T 932-1988 气密单耳托板自锁螺母 Self-locking nuts,singlelug, anchor, sealing,199 GB/T 933-1988 气密双耳托板自锁螺母 Self-locking nuts,twolug, anchor, sealing200 GB/T 937-1988 成组游动托板自锁螺母 Self-locking nuts, anchor, floating,Gang channel 201 GB/T 938-1988 游动自锁螺母 Self-locking nuts, floating202 GB/T 939-1988 单耳托板自锁螺母保护罩 Boots for self-locking nuts, singlelug, anchor203 GB/T 940-1988 双耳托板自锁螺母保护罩 Boots for self-lockingnuts,twolug, anchor204 GB/T 941-1988 角形托板自锁螺母保护罩 Boots for self-lockingnuts,angle, anchor205 GB/T 943-1988 自锁螺母技术条件 Procurement specification forself-locking nuts206 GB/T 945-1976 十字槽球面中柱头螺钉 Screws,cross recessed,thin raised cheese head207 GB/T 946-1988 开槽球面圆柱头轴位螺钉 Slotted raised cheese head with shoulder208 GB/T 947-1988 开槽球面大圆柱头螺钉 Slotted large raised cheese head screws209 GB/T 948-1988 开槽沉头不脱出螺钉 Slotted countersunk head screws with waisted shank210 GB/T 949-1988 开槽半沉头不脱出螺钉 Slotted raised countersunk head screws with waisted shank211 GB/T 950-1986 十字槽圆头木螺钉 Cross recessed round head wood screws 212 GB/T 951-1986 十字槽沉头木螺钉 Cross recessed countersunk head wood screws213 GB/T 952-1986 十字槽半沉头木螺钉 Cross recessed raised countersunk head wood screws214 GB/T 953-1988 等长双头螺柱 C 级 Double end studs (clampingtype)--Product grade C215 GB/T 954-1986 120° 沉头铆钉120°degree countersunk head rivets 216 GB/T 955-1987 波形弹性垫圈 Wave spring washers217 GB/T 956.1-1987 锥形锁紧垫圈 Countersunk external toothed lock washers218 GB/T 956.2-1987 锥形锯齿锁紧垫圈 Countersunk serrated external toothed lock washers219 GB/T 959.1-1986 挡圈技术条件 -- 弹性挡圈 Specifications for ring—Circlips220 GB/T 959.2-1986 挡圈技术条件 -- 钢丝挡圈 Specifications for ring—Round wire snap rings221 GB/T 959.3-1986 挡圈技术条件 -- 切制挡圈 Specifications for ring—Cutting rings222 GB/T 960-1986 夹紧挡圈 Grip rings223 GB/T 961-1988 单耳托板自锁螺母垫片 Spacers for self-lockingnuts,singlelug, anchor224 GB/T 962-1988 双耳托板自锁螺母垫片 Spacers for self-lockingnuts,twolug, anchor225 GB/T 963-1988 角形托板自锁螺母垫片 Spacers for self-lockingnuts,angle, anchor226 GB/T 973-1976 十字槽扁圆头螺钉 Screws,cross recessed,oval head 227 GB/T 974-1976 十字槽120° 半沉头螺钉 Screws,crossrecessed,120°raised countersunk head228 GB/T 975-1986 管状铆钉 Pipe type rivets229 GB/T 1007-1976 小六角较扁螺母 Small hexagon medium thin nuts230 GB/T 1009-1978 螺母专用技术条件 Specified specifications for nuts231 GB/T 1011-1986 大扁圆头铆钉 Truss head rivets232 GB/T 1012-1986 120° 半沉头铆钉120°degree oval countersunk rivets 233 GB/T 1013-1986 平锥头半空心铆钉 Cone head semi-tubuler rivets234 GB/T 1014-1986 大扁圆头半空心铆钉 Truss head semi-tubuar rivets 235 GB/T 1015-1986 沉头半空心铆钉 Countersunk head semi-tublar rivets 236 GB/T 1016-1986 无头铆钉 Headless rivets237 GB/T 1017-1978 铆钉专用技术条件 Specified specifications for rivets 238 GB/T 1021-1976 角形垂直单耳止动垫圈 Lock washers with angular upturn tab perpendicular to the lug239 GB/T 1022-1976 角形单耳止动垫圈 Lock washers with angular upturn tab in line to the lug240 GB/T 1023-1976 角形垂直外舌止动垫圈 Lock washers with angular upturn tab perpendicular to the external tab241 GB/T 1024-1976 角形外舌止动垫圈 Lock washers with angular upturn tab in line to the external tab242 GB/T 1030-1988 内球面垫圈 Inner sphere washers243 GB/T 1047-1995 管道元件的公称通径 Nominal size for pipe components 244 GB/T 1048-1990 管道元件公称压力 Nominal pressure for pipe components 245 GB/T 1095-1979 平键键和键槽的剖面尺寸 Parallel keys--Dimensions of cross sections and keyways246 GB/T 1096-1979 普通平键型式尺寸 Plain parallel keys--Types and dimensions247 GB/T 1097-1979 导向平键型式尺寸 Feather keys--Types and dimensions 248 GB/T 1098-1979 半圆键键和键槽的剖面尺寸 Semi-circular (Woodruff) keys--Dimensions of cross sections and keyways249 GB/T 1099-1979 半圆键型式尺寸 Woodruff keys--Types and dimensions 250 GB/T 1144-1987 矩形花键尺寸、公差和检验 Straight-sided spline—Dimensions tolerances and verification251 GB/T 1168-1976 螺柱技术条件 Studs--Technical requirements252 GB/T 1228-1991 钢结构用高强度大六角头螺栓 High strength bolts with large hexagon head for steel structures 253 GB/T 1229-1991 钢结构用高强度大六角螺母 High strength large hexagon nuts for steel structures 254 GB/T 1230-1991 钢结构用高强度垫圈 High strength plain washers for steel structures255 GB/T 1231-1991 钢结构用高强度大六角头螺拴、大六角螺母、垫圈技术条件 Specifications of high strength bolts with large hexa-gon head, large hexagon nuts, plain washers for steel structures256 GB/T 1237-1988 紧固件的标记方法 Designation system for fasteners 257 GB/T 1337-1988 六角自锁螺母 Self-locking nuts,hexagon258 GB/T 1338-1988 小六角扁自锁螺母 Self-locking nuts,reduced hexagon oblate259 GB/T 1339-1988 小六角自锁螺母 Self-locking nuts,reduced hexagon 260 GB/T 1340-1988 成组游动托板自锁螺母支架 Supports for self-locking nuts,anchor floating,Gang channel261 GB/T 1356-1988 淅开线圆柱齿轮基本齿廓 Basic rack tooth profile of involute cylindrical gears262 GB/T 1357-1987 渐开线圆柱齿轮模数 Modules of involute cyindrical gears263 GB/T 1563-1979 楔键键和键槽的剖面尺寸 Taper keys--Cross section dimensions of keys and keyways264 GB/T 1564-1979 普通楔键型式尺寸 Taper keys for general use--Types and dimensions265 GB/T 1565-1979 钩头楔键型式尺寸 Gib-head taper keys--Types and dimensions266 GB/T 1566-1979 薄型平键键和键槽的剖面尺寸 Thin flat keys--Cross section dimensions and keyways267 GB/T 1567-1979 薄型平键型式尺寸 Thin flat keys--Types and dimensions277 GB/T 2672-1986 内六角花形盘头螺钉 Hexagon lobular socket pan head screws278 GB/T 2673-1986 内六角花形沉头螺钉 Hexagon lobular socket countersunk head screws279 GB/T 2674-1986 内六角花形半沉头螺钉 Hexagon lobular socket raised countersunk head screws450 GB/T 5281-1985 内六角圆柱头轴肩螺钉 Hexagon socket head shoulder screws451 GB/T 5282-1985 开槽盘头自攻螺钉 Slotted pan head tapping screws 452 GB/T 5283-1985 开槽沉头自攻螺钉 Slotted countersunk head tapping screws453 GB/T 5284-1985 开槽半沉头自攻螺钉 Slotted raised countersunk head tapping screws454 GB/T 5285-1985 六角头自攻螺钉 Hexagon head tapping screws455 GB/T 5286-1985 螺栓、螺钉和螺母用平垫圈总方案 Plain washers for bolts,screws and nuts--General plan456 GB/T 5287-1985 特大垫圈 C 级 Plain washers--Extra largeseries--Product grade C510 GB/T 5780-1986 六角头螺栓 --C 级 Hexagon head bolts—Product grade C511 GB/T 5781-1986 六角头螺栓 -- 全螺纹 --C 级 Hexagon head bolts—Full thread—Product grade C512 GB/T 5782-1986 六角头螺栓 --A 和 B 级 Hexagon head bolts—Product grades A and B513 GB/T 5783-1986 六角头螺栓 -- 全螺纹 A 和 B 级 Hexagon head bolts—Full thread—Product grades A and B514 GB/T 5784-1986 六角头螺栓 -- 细杆 B 级 Hexagon head bolts—Reduced shank—Product grade B515 GB/T 5785-1986 六角头螺栓 -- 细牙 --A 和 B 级 Hexagon head bolts—Fine pitch thread—Product grades A and B516 GB/T 5786-1986 六角头螺栓细牙全螺纹 A 和 B 级 Hexagon head bolts—Fine pitch thread—Full thread—Product grades A and B517 GB/T 5787-1986 六角法兰面螺栓 --B 级 Hexagon flange bolts—Product grade B518 GB/T 5788-1986 六角法兰面螺栓 -- 细杆 --B 级 Hexagon flangebolts--Reduced shank--Product grade B519 GB/T 5789-1986 六角法兰面螺栓 -- 加大系列 --B 级 Hexagon flange bolts—Heavy series—Product grade B520 GB/T 5790-1986 六角法兰面螺栓 -- 加大系列 -- 细杆 --B 级 Hexagon flange bolts—Heavg eries--Product grade B532 GB/T 6170-1986 1 型六角螺母 A 和 B 级 Hexagon nuts, style 1--Product grades A and B533 GB/T 6171-1986 1 型六角螺母细牙 A 和 B 级 Hexagon nuts, style1--Fine pitch thread--Product gra des A and B534 GB/T 6172-1986 六角薄螺母 A 和 B 级倒角 Hexagon thin nuts--Product grades A and B--Chamfered535 GB/T 6173-1986 六角薄螺母细牙 A 和 B 级 Hexagon thin nuts--Fine pitch thread--Product grades A and B536 GB/T 6174-1986 六角薄螺母 B 级无倒角 Hexagon thin nuts--Product grade B--Unchamfered537 GB/T 6175-1986 2 型六角螺母 A 和 B 级 Hexagon nuts, style 2--Product grades A and B538 GB/T 6176-1986 2 型六角螺母细牙 A 和 B 级 Hexagon nuts, style2--Fine pitch thread--Product grades A and B539 GB/T 6177-1986 六角法兰面螺母 A 级 Hexagon nuts withflange--Product grade A540 GB/T 6178-1986 1 型六角开槽螺母 A 和 B 级 Hexagon slotted and castle nuts, style 1--Product grades A and B541 GB/T 6179-1986 1 型六角开槽螺母 C 级 Hexagon slotted nuts, style 1--Product grade C542 GB/T 6180-1986 2 型六角开槽螺母 A 和 B 级 Hexagon slotted and castle nuts,style 2--Product grades A and B543 GB/T 6181-1986 六角开槽薄螺母 A 和 B 级 Hexagon thin slottednuts--Product grades A and B544 GB/T 6182-1986 2 型非金属嵌件六角锁紧螺母 Prevailing torque type hexagon nuts (with non-metallic insert), style 2545 GB/T 6183-1986 非金属嵌件六角法兰面锁紧螺母 Prevailing torque type hexagon nuts with flange (with non-metallic insert)546 GB/T 6184-1986 1 型全金属六角锁紧螺母 Prevailing torque typeall-metal hexagon nuts, style 1547 GB/T 6185-1986 2 型全金属六角锁紧螺母 Prevailing torque typeall-metal hexagon nuts, style 2--Property classes548 GB/T 6186-1986 2 型全金属六角锁紧螺母 9 级 Prevailing torque type all-metal hexagon nuts, style 2--Property class 9549 GB/T 6187-1986 全金属六角法兰面锁紧螺母 Prevailing torque typeall-metal hexagon nuts with flange550 GB/T 6188-1986 紧固件用六角花形 T 型 Hexagon lobular forfasteners--Type T551 GB/T 6189-1986 紧固件用六角花形 E 型 Hexagon lobular forfasteners--Type E552 GB/T 6190-1986 内六角花形圆柱头螺钉 4.8 级 Hexagon lobular socket head cap screws--Property class 4.8553 GB/T 6191-1986 内六角花形圆柱头螺钉 8.8 级 Hexagon lobular socket head cap screws--Property class 8.8562 GB/T 6560-1986 十字槽盘头自攻锁紧螺钉 Cross recessed pan head thread forming screws563 GB/T 6561-1986 十字槽沉头自攻锁紧螺钉 Cross recessed countersunk head thread forming screws564 GB/T 6562-1986 十字槽半沉头自攻锁紧螺钉 Cross recessed raised countersunk head thread forming screws565 GB/T 6563-1986 六角头自攻锁紧螺钉 Hexagon head thread forming screws 566 GB/T 6564-1986 内六角花形圆柱头自攻锁紧螺钉 Hexagon lobular socket thread forming screws573 GB/T 7244-1987 重型弹簧垫圈 Single coil spring lock washers, Heavy type574 GB/T 7245-1987 鞍形弹簧垫圈 Curved single coil spring lock washers 575 GB/T 7246-1987 波形弹簧垫圈 Wave single coil spring lock washers 587 GB/T 8262-1987 圆头椭圆颈螺栓 Bolts,round head with oval neck594 GB/T 9074.1-1988 十字槽盘头螺钉和平垫圈组合件 Cross recessed pan head screw and plain washer assemblies595 GB/T 9074.2-1988 十字槽盘头螺钉和外锯齿锁紧垫圈组合件 Cross recessed pan head screw and serrated lock washer external teeth assemblies 596 GB/T 9074.3-1988 十字槽盘头螺钉和弹簧垫圈组合件 Cross recessed pan head screw and single coil spring lock washer assemblies597 GB/T 9074.4-1988 十字槽盘头螺钉 , 弹簧垫圈和平垫圈组合件 Cross recessed pan head screw,single coil spring lock washer and plain washer assemblies598 GB/T 9074.5-1988 十字槽小盘头螺钉和平垫圈组合件 Cross recessed small pan head screw and small plain washer assemblies599 GB/T 9074.6-1988 十字槽小盘头螺钉和大垫圈组合件 Cress recessed small pan head serew and big plain washer assemblies600 GB/T 9074.7-1988 十字槽小盘头螺钉和弹簧垫圈组合件 Cross recessed small pan head screw and single coil spring lock washer assemblies 601 GB/T 9074.8-1988 十字槽小盘头螺钉和弹簧垫圈及平垫圈组合件 Cross recessed small pan head screw,single coil spring lock washer and plain washer assemblies602 GB/T 9074.9-1988 十字槽沉头螺钉和锥形锁紧垫圈组合件 Cross recessed countersunk head screw and countersunk serrated external toothed lockwasher assemblies603 GB/T 9074.10-1988 十字槽半沉头螺钉和锥形锁紧垫圈组合件 Cross recessed raised countersunk head screw and countersunk external toothed lock washer assemblies604 GB/T 9074.11-1988 十字槽凹穴六角头螺栓和平垫圈组合件 Cross recessed hexagon bolt with indentation and plain washer assemblies 605 GB/T 9074.12-1988 十字槽凹穴六角头螺栓和弹簧垫圈组合件 Cross recessed hexagon bolt with indentation and single coil spring lock washer assemblies606 GB/T 9074.13-1988 十字槽凹穴六角头螺栓 , 弹簧垫圈和平垫圈组合件Cross recessed hexagon bolt with indentation, single coil lock washer and plain washer assemblies607 GB/T 9074.14-1988 六角头螺栓和平垫圈组合件 Hexagon head bolt and plain washer assemblies608 GB/T 9074.15-1988 六角头螺栓和弹簧垫圈组合件 Hexagon head bolt and single coil spring lock washer assemblies609 GB/T 9074.16-1988 六角头螺栓和外锯齿锁紧垫圈组合件 Hexagon head bolt and serrated lock washer external teeth assemblies610 GB/T 9074.17-1988 六角头螺栓 , 弹簧垫圈和平垫圈组合件 Hexagon head bolt, single coil spring lock washer and plain washer assemblies611 GB/T 9074.18-1988 十字槽盘头自攻螺钉和平垫圈组合件 Cross recessed pan head tapping screw and plain washer assemblies612 GB/T 9074.19-1988 十字槽盘头自攻螺钉和大垫圈组合件 Cross recessed pan head tapping screw and large plain washer assemblies613 GB/T 9074.20-1988 十字槽凹穴六角头自攻螺钉和平垫圈组合件 Cross recessed hexagon head tapping sorew with indentation and plain washer assemblies614 GB/T 9074.21-1988 十字槽凹穴六角头自攻螺钉和大垫圈组合件 Cross recessed hexagon head tapping screw with indentation and large plain washer assemblies615 GB/T 9074.22-1988 六角头自攻螺钉和平垫圈组合件 Hexagon head tapping screw and plain washer assemblies616 GB/T 9074.23-1988 六角头自攻螺钉和大垫圈组合件 Hexagon head tapping screw and big washer assemblies617 GB/T 9074.24-1988 组合件用平垫圈 Plain washer for assembly618 GB/T 9074.25-1988 组合件用大垫圈 Big plain washer for assembly 619 GB/T 9074.26-1988 组合件用弹簧垫圈 Single coil spring lock washer for assembly620 GB/T 9074.27-1988 组合件用外锯齿锁紧垫圈 Serrated lock washer external teeth for assembly621 GB/T 9074.28-1988 组合件用锥形锁紧垫圈 Countersunk external toothed lock washer for assembly622 GB/T 9074.29-1988 自攻螺钉组合件用平垫圈 Samll wasner for tapping screw assembly623 GB/T 9074.30-1988 自攻螺钉组合件用大垫圈 Big washer for tapping screw assembly808 GB/T 9456-1988 十字槽凹穴六角自攻螺钉 Cross recessed hexagon head tapping screws with indentation809 GB/T 9457-1988 1 型六角开槽螺母细牙 A 和 B 级 Hexagon slotted and castle nuts, style l--Fine pitch thread--Product grades A and B810 GB/T 9458-1988 2 型六角开槽螺母细牙 A 和 B 级 Hexagon slotted and castle nuts, style 2--Fine pitch thread--Product grades A and B811 GB/T 9459-1988 六角开槽薄螺母细牙 A 和 B 级 Hexagon thin slotted nuts--Fine pitch thread--Product grades A and B840 GB/T 10432-1989 无头焊钉 Headless studs for stud welding841 GB/T 10433-1989 圆柱头焊钉 Cheese head studs for stud welding900 GB/T 12615-1990 封闭型扁圆头抽芯铆钉 Mushroom head break mandrel closed end blind rivets900 GB/T 12615-1990 封闭型扁圆头抽芯铆钉 Mushroom head break mandrel closed end blind rivets922 GB/T 13680-1992 焊接方螺母 Square weld nuts923 GB/T 13681-1992 焊接六角螺母 Hexagon weld nuts927 GB/T 13806.1-1992 精密机械用紧固件十字槽螺钉 Fasteners for fine mechanics--Cross recessed screws928 GB/T 13806.2-1992 精密机械用紧固件十字槽自攻螺钉刮削端 Fasteners for fine mechanics--Cross recessed tapping screws--Scrape point937 GB/T 14210-1993 墙板自攻螺钉 Dry wall screws972 GB/T 15855.1-1995 扁圆头击芯铆钉 Flat round head drive rivets973 GB/T 15855.2-1995 沉头击芯铆钉 Countersunk head drive rivets974 GB/T 15855.3-1995 击芯铆钉技术条件 Specifications for drive rivets 975 GB/T 15856.1-1995 十字槽盘头自钻自攻螺钉 Cross recessed pan head self-drilling tapping screws976 GB/T 15856.2-1995 十字槽沉头自钻自攻螺钉 Cross recessed countersunk head self-drilling tapping screws977 GB/T 15856.3-1995 十字槽半沉头自钻自攻螺钉 Cross recessed raised countersunk head self-drilling tapping screws978 GB/T 15856.4-1995 六角法兰面自钻自攻螺钉 Hexagon flange headself-drilling tapping screws991 GB/T 16824.1-1997 六角凸缘自攻螺钉 Hexagon head tapping screws with collar992 GB/T 16824.2-1997 六角法兰面自攻螺钉 Hexagon flange head tapping screws1005 GB/T 96-1985 大垫圈 -A 和 C 级 Plain washers--Largeseries--Product grades A and C1006 GB/T 97.1-1985 平垫圈 -A 级 Plain washers--Normal series--Product grade A1007 GB/T 97.2-1985 平垫圈倒角型 -A 级 Plainwashers--Chamfered--Normal series--Product grade A1008 GB/T 98-1988 止动垫圈技术条件 Specification for tab washer1009 GB/T 99-1986 开槽圆头木螺钉 Slotted round head wood screws1010 GB/T 100-1986 开槽沉头木螺钉 Slotted countersink head wood screws 1011 GB/T 101-1986 开槽半沉头木螺钉 Slotted raised countersunk head wood screws1012 GB/T 102-1986 六角头木螺钉 Hexagon head wood screws1013 GB/T 109-1986 平头铆钉 Flat head rivets1014 GB/T 116-1986 铆钉技术条件 Specifications for rivet1015 GB/T 117-1986 圆锥销 Taper pins1016 GB/T 118-1986 内螺纹圆锥销 Taper pins with internal thread1017 GB/T 119-1986 圆柱销 Parallel pins1018 GB/T 120-1986 内螺纹圆柱销 Parallel pins with internal thread 1005 GB/T 96-1985 大垫圈 -A 和 C 级 Plain washers--Largeseries--Product grades A and C1006 GB/T 97.1-1985 平垫圈 -A 级 Plain washers--Normal series--Product grade A1007 GB/T 97.2-1985 平垫圈倒角型 -A 级 Plainwashers--Chamfered--Normal series--Product grade A1008 GB/T 98-1988 止动垫圈技术条件 Specification for tab washer1009 GB/T 99-1986 开槽圆头木螺钉 Slotted round head wood screws1010 GB/T 100-1986 开槽沉头木螺钉 Slotted countersink head wood screws 1011 GB/T 101-1986 开槽半沉头木螺钉 Slotted raised countersunk head wood screws1012 GB/T 102-1986 六角头木螺钉 Hexagon head wood screws1013 GB/T 109-1986 平头铆钉 Flat head rivets1014 GB/T 116-1986 铆钉技术条件 Specifications for rivet1015 GB/T 117-1986 圆锥销 Taper pins1016 GB/T 118-1986 内螺纹圆锥销 Taper pins with internal thread1017 GB/T 119-1986 圆柱销 Parallel pins1018 GB/T 120-1986 内螺纹圆柱销 Parallel pins with internal thread。
螺丝品名代号中英文对照表
SAW SLOT
14
N
#2 SQUARE RECESS（UAB）
2号四角孔（UAB）客户
#2 SQ
15
O
#0 SQUARE RECESS
0号四角孔
#0 SQ
16
P
#2 PHILLPS RECESS
2号十字孔
#2 PHIL
17
Q
#2 SQUARE RECESS
2号四角孔
#2 SQ
18
R
MFGR MARKS “TY”
SELF TAPPING SCREWS DIN STANDARD
自攻螺丝（DIN标准）
S/T/S TO DIN
25
Y
DRYWALL SCREWS墙用螺丝（MM） NhomakorabeaD/W/S
26
Z
SELF DRILL SCREWS
钻尾螺丝（IN+MM）
S/D/S
27
0
METAL NEOPRENE WASHER
铁华司+橡胶华司
澳洲墙用螺丝
DRYWALL SCREWS
11
K
SELF TAPPING SCREWS
澳洲攻牙螺丝
SELF TAPPING SCREWS
12
L
SELF DRILL SCREWS（TEK SCREW）
钻尾螺丝（IN）
S/D/S
13
M
MACHINE SCREWS
机械螺丝（IN）
M/S
14
N
NUTS
螺帽（IN）
头记“TY”
WITH MFGR MARKS “TY“
19
S
STRUCK SLOT
紧固件 螺丝 中英文对照表
螺丝产品名称中英文对照(螺丝螺)六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS)六角机械螺丝 HEX HEAD MACHINE BOLTS六角木牙螺丝 HEX LAG BOLTS四角螺丝 SQUARE HEAD BOLTST头螺丝 T HEAD BOLTS马车螺丝 CARRIAGE BOLTS环首螺丝 EYE BOLTS内六角孔螺丝 HEX SOCKET CAP SCREWS固定螺丝 SET SCREWS螺椿栓 STUD BOLTS螺旋椿 SCREW STUDS轮壳螺栓 WHEEL BOLTS翼形螺丝 WING SCREWS自攻螺丝 SELF TAPPING SCREWS自削螺丝 THREAD CUTTING SCREWS钻尾螺丝 SELF DRILLING SCREWS旋入螺丝 DRIVE SCREWS机械螺丝 MACHINE SCREWS木螺丝 WOOD SCREWS家具螺丝 FURNITURE SCREWS塑板螺丝 CHIPBOARD SCREWS墙用螺丝 DRYWALL SCREWS基础螺栓 FOUNDATION BOLTSU型螺栓 U BOLTS勾头螺栓 HOOK BOLTS套挂螺丝 TOGGLE BOLTS突缘螺丝 FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS耐候钢螺丝 CORTEN STEEL HEAVY HEX BOLTS扭矩控制螺栓 T.C.BOLTS高张力螺栓 HIGH STRENGTH BOLTS剪力钉(焊接螺丝) WELDING STUDS螺丝附华司组合 SCREWS AND WASHERS ASSEMBLED(SEMS) 大尺寸螺栓 BIG SIZE BOLTS不锈钢小螺丝 STAINLESS STEEL SHEET METAL SCREWS 不锈钢大螺丝 STAINLESS STEEL BOLTS铜螺丝 BRASS SCREWS铝螺丝 ALUMINUM SCREWS合金钢螺丝 ALLOY STEEL SCREWS电子螺丝 ELECTRONIC SCREWS微小精密螺丝 MICRO SCREWS塑胶螺丝 PLASTIC SCREWS复合材料用螺丝 PARTICLE BOARD SCREWS钛合金螺丝 TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料 TI,ZR,MO,NB PARE METAL BOLTS PARTS 拇指螺丝 THUMB SCREWS双头牙螺丝 DOUBLE END SCREWS HANGER BOLT车辆(汽车)螺丝、螺帽 AUTOMOTIVE FASTENERS航太用螺丝 AEROSPACE FASTENERS飞机特殊扣件 SOURCE CONTROL BOLTS拉栓 BLIND BOLTS面板螺丝 PANEL FASTENERS电梯螺丝 ELEVATOR BOLTS四角头固定螺丝 SQUARE SET SCREWS大头马车螺丝 STEP BOLTS单向螺丝 ONE WAY LAG SCREWS管夹螺丝 HOSE CLAMP SCREWS不锈钢固定螺丝 STAINLESS STEEL HEX SOCKET CAP SCREWS不锈钢内六角螺丝 STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝 HINGE SCREWS货柜螺丝 CONTAINER SCREWS复合材料钻尾螺丝 BI-METAL SELF DRILLING SCREWS三角牙螺丝 TRILOBULAR THREAD SCREWS高低牙螺丝 HIGH LOW SCREWS夹板用螺丝 PARTICLE BOARD SCREWS马桶螺丝 TOILET CLOSET BOLTS特长螺丝 SPECIAL LONGER SCREWS建业螺丝 BUILDING FASTENERS不锈钢六角螺丝 STAINLESS STEEL HEX SOCKET CAP SCREWS其它特殊螺丝 SPECIAL SCREWS OR BOLTS不锈钢特殊螺丝 SPECIAL STAINLESS STEEL SCREWS宽牙螺丝（粗牙螺丝） COARSE THREAD SCREWS链带螺丝 COLLATED SCREWS机(踏)车用螺丝、轴心 SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE针车用螺丝、轴心 SCREWS AND SHAFTS FOR SEWING MACHING止付螺丝 SOCKET SET SCREWS水泥螺丝 CONCRETE SCREWS板模螺丝 CONSTRUCTION BOLTS涞□萁z DIE CAST WING SCREWS; ZINC ALLOY重型车螺丝 HEAVY DUTY WHEEL HUB BOLTS内六角固定螺丝 HEX SOCKET SET SCREWS复合材料用螺丝（夹板用） PARTICLE BOARD SCREWS犁壁螺丝 PLOW BOLTS不锈钢宽牙螺丝 STAINLESS STEEL COARSE THREAD SCREWS不锈钢高低牙螺丝 STAINLESS STEEL HIGH-LOW THREAD SCREWS不锈钢机械螺丝 STAINLESS STEEL MACHINE SCREWS不锈钢钻尾螺丝 STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝 STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺丝 STAINLESS STEEL THREAD CUTTING SCREWS不锈钢三角牙螺丝 STAINLESS STEEL TRI-LOBULAR THREAD SCREWS 不锈钢木螺丝 STAINLESS STEEL WOOD SCREWS套挂螺栓及螺丝 TOGGLE BOLTS钛合金膨胀螺丝 TITANIUM ALLOY EXPANSION BOLTS。
关于螺丝的中英文对照25页word
(浏览56次) No. 英文单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread PT 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝（机牙螺丝）32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标螺丝相关参数英语对照A: Machine Screw: 机械螺丝B: Tapping Screw: 自攻螺丝 (分使用于金属与使用于塑料二种) B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝)C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金 5052d. Brass: 黄铜e. Bronze: 青铜f. UNS C11000 Copper: 锑铜Finish Code: 外观处理规格Head Code: 头部外型螺丝型号 Drive Code: 头部剖沟,特征型号Length Code: 螺丝长度 (mm)A-1: Thread Code: 螺丝型号A-2: Length Code: 螺丝长度:A-3: Drive Code/ 头部剖沟,特征.a. Slotted: 一字 ( Minus )b. Phillips: 十字 ( Plus )c. Phil-Slot: 一字/十字d. Hex Scoket: 内六角e. One Way: 单向 (只可锁入,不可退出)A-4: Head Code/ 头部外型.a. Flat: 平头 (锁入后,顶部与工作件齐平)b. Oval: 色拉头c. Round: 圆头d. Pan: 圆扁头e. Truss: 大圆扁头f. Hex : 六角头A-5: Finish Code/ 外观处理.a. Z: Zine-Plated: 镀锌b. Ni: Ni-Plated: 镀镍c. Tin-Plated: 镀锡d. Zine Plated / Green Iridite: 镀锌绿膜处理.e. Radiant Plated: 镀五彩f. Passivate: 抗氧化处理.g. Alodial Finish: 无外观处理螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度各类紧固件标准件产品英语翻译对照插片壁虎 Steel Ceiling Anchors内迫壁虎 Drop in Anchors碳钢锤钉壁虎 Steel Hit Anchors碳钢六角螺帽 Steel Hex Coupling Nuts强力车修壁虎 Wedge Anchors外迫壁虎 Cut Anchors化学壁虎 Chemical Anchors不锈钢重载胀栓 Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽 Tie Wire Anchors锌合金打入式壁虎 Hammer Drive Anchors弹簧螺帽 Strut Nuts兰花夹系列 Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎 Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎 Hollow Wall Anchors套管式壁虎 Sleeve Anchors打入式壁虎鱼形尼龙壁虎 Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎 Hit Anchors电梯壁虎 Bolt Anchors重载壁虎 Heavy duty anchors两片夹 Loxin Masonry Anchors定位螺栓 Set Bolts长型兰花夹 Short Strap Anchors工具棒 Drop in Setting Tools象脚壁虎 Elephant foot anchors水泥预埋件 Concrete Insert翻边胀轴 Drop in Anchor with Lip冲件 Legs Drywall Anchors六角盖头螺帽 Hex Cap Nuts六角锯齿螺帽 Hex Serrated Nuts六角轮缘螺帽 Hex Flange Nuts高脚螺帽 Hex Coupling Nuts(High Nuts) 圆螺帽 Round Nuts四角螺帽 Square Nuts管用螺帽 Pipe Nuts轮壳螺帽 Wheel Nuts蝶型螺帽 Wing NutsU形螺帽 U NutsT形螺帽 T Nuts环首螺帽 Eye Nuts齿形螺帽 Kep Nuts齿花螺帽 Clinch Nuts耐候钢六角重型螺帽 Corten Steel Heavy Hex Nuts焊接螺帽 Weld Nuts高张力螺帽 Heigh Strength Nuts建业用螺帽 Structural Nuts不锈钢螺帽 Stainless Steel Nuts铜螺帽 Brass Nuts铝螺帽 Aluminum Nuts合金钢螺帽 Alloy Steel Nuts重型车螺帽 Heavy Duty Wheel Hub Nuts铁器焊接袋帽 Acorn Cap Nuts金属预置扭矩式螺帽 All-Metal Prevailing Torque Type Nuts 壁虎螺帽 Anchor Nuts大尺寸螺帽 Big Size Nuts铁盖袋帽 Closed End Acorn Nuts盘形华司螺帽 Conical Washer Nuts铁盖+尼龙圈组合盖帽 Din 986 Domed Cap Nuts突缘尼龙盖帽 Flange Nylon Insert Lock Nuts平面华司螺帽 Flat Waser Nuts六角割沟螺帽 Hex Slotted Nut自锁螺帽 Self-Locking Nuts制止螺帽 Sliding NutsSln-自动防松螺帽 Sln Self-Locking Nuts其它特殊螺帽 Special Nuts弹簧螺帽 Spring Nuts不锈钢突缘螺帽 Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽 Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽 Stainless Steel Heavy Hex Nuts不锈钢六角螺帽 Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽 Stainless Steel Nylon Insert Lock Nuts普通六角螺帽 Hex Nuts六角重型螺帽 Heavy Hex Nuts薄型螺帽 Hex Jam Nuts尼龙嵌入防松螺帽 Nylon Insert Lock Nuts机械螺丝用六角螺帽 Hex Machine Screw Nut六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝 Hex Head Machine Bolts六角木牙螺丝 Hex Lag Bolts四角螺丝 Square Head BoltsT头螺丝 T Head Bolts马车螺丝 Carriage Bolts环首螺丝 Eye Bolts内六角孔螺丝 Hex Socket Cap Screws固定螺丝 Set Screws螺椿栓 Stud Bolts螺旋椿 Screw Studs轮壳螺栓 Wheel Bolts翼形螺丝 Wing Screws自攻螺丝 Self Tapping Screws自削螺丝 Thread Cutting Screws钻尾螺丝 Self Drilling Screws旋入螺丝 Drive Screws机械螺丝 Machine Screws木螺丝 Wood Screws家具螺丝 Furniture Screws塑板螺丝 Chipboard Screws墙用螺丝 Drywall Screws基础螺栓 Foundation BoltsU型螺栓 U Bolts勾头螺栓 Hook Bolts套挂螺丝 Toggle Bolts突缘螺丝 Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝 Corten Steel Heavy Hex Bolts 扭矩控制螺栓 T.C.Bolts高张力螺栓 High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合 Screws And Washers Assembled(Sems)大尺寸螺栓 Big Size Bolts不锈钢小螺丝 Stainless Steel Sheet Metal Screws不锈钢大螺丝 Stainless Steel Bolts铜螺丝 Brass Screws铝螺丝 Aluminum Screws合金钢螺丝 Alloy Steel Screws电子螺丝 Electronic Screws微小精密螺丝 Micro Screws塑料螺丝 Plastic Screws复合材料用螺丝 Particle Board Screws钛合金螺丝 Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料 Ti,Zr,Mo,Nb Pare Metal Bolts Parts 拇指螺丝 Thumb Screws双头牙螺丝 Double End Screws Hanger Bolt车辆(汽车)螺丝、螺帽 Automotive Fasteners航天用螺丝 Aerospace Fasteners飞机特殊扣件 Source Control Bolts拉栓 Blind Bolts面板螺丝 Panel Fasteners电梯螺丝 Elevator Bolts四角头固定螺丝 Square Set Screws大头马车螺丝 Step Bolts单向螺丝 One Way Lag Screws管夹螺丝 Hose Clamp Screws不锈钢固定螺丝 Stainless Steel Hex Socket Cap Screws 不锈钢内六角螺丝 Stainless Steel Hex Socket Cap Screws 铰链螺丝 Hinge Screws货柜螺丝 Container Screws复合材料钻尾螺丝 Bi-Metal Self Drilling Screws三角牙螺丝 Trilobular Thread Screws高低牙螺丝 High Low Screws夹板用螺丝 Particle Board Screws马桶螺丝 Toilet Closet Bolts特长螺丝 Special Longer Screws建业螺丝 Building Fasteners不锈钢六角螺丝 Stainless Steel Hex Socket Cap Screws 其它特殊螺丝 Special Screws Or Bolts不锈钢特殊螺丝 Special Stainless Steel Screws宽牙螺丝（粗牙螺丝） Coarse Thread Screws链带螺丝 Collated Screws水泥螺丝 Concrete Screws板模螺丝 Construction Bolts锌蝶螺丝 Die Cast Wing Screws; Zinc Alloy重型车螺丝 Heavy Duty Wheel Hub Bolts内六角固定螺丝 Hex Socket Set Screws复合材料用螺丝（夹板用） Particle Board Screws 犁壁螺丝 Plow Bolts不锈钢木螺丝 Stainless Steel Wood Screws套挂螺栓及螺丝 Toggle Bolts钛合金膨胀螺丝 Titanium Alloy Expansion Bolts六角盖头螺帽 Hex Cap Nuts六角锯齿螺帽 Hex Serrated Nuts六角轮缘螺帽 Hex Flange Nuts高脚螺帽 Hex Coupling Nuts(High Nuts)圆螺帽 Round Nuts四角螺帽 Square Nuts管用螺帽 Pipe Nuts轮壳螺帽 Wheel Nuts蝶型螺帽 Wing NutsU形螺帽 U NutsT形螺帽 T Nuts环首螺帽 Eye Nuts齿形螺帽 Kep Nuts齿花螺帽 Clinch Nuts耐候钢六角重型螺帽 Corten Steel Heavy Hex Nuts焊接螺帽 Weld Nuts高张力螺帽 Heigh Strength Nuts建业用螺帽 Structural Nuts不锈钢螺帽 Stainless Steel Nuts铜螺帽 Brass Nuts铝螺帽 Aluminum Nuts合金钢螺帽 Alloy Steel Nuts重型车螺帽 Heavy Duty Wheel Hub Nuts铁器焊接袋帽 Acorn Cap Nuts金属预置扭矩式螺帽 All-Metal Prevailing Torque Type Nuts 壁虎螺帽 Anchor Nuts大尺寸螺帽 Big Size Nuts铁盖袋帽 Closed End Acorn Nuts盘形华司螺帽 Conical Washer Nuts铁盖+尼龙圈组合盖帽 Din 986 Domed Cap Nuts突缘尼龙盖帽 Flange Nylon Insert Lock Nuts平面华司螺帽 Flat Waser Nuts六角割沟螺帽 Hex Slotted Nut自锁螺帽 Self-Locking Nuts制止螺帽 Sliding NutsSln-自动防松螺帽 Sln Self-Locking Nuts其它特殊螺帽 Special Nuts弹簧螺帽 Spring Nuts不锈钢突缘螺帽 Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽 Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽 Stainless Steel Heavy Hex Nuts不锈钢六角螺帽 Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽 Stainless Steel Nylon Insert Lock Nuts锌压属螺帽 Zinc Die Casting Nuts普通六角螺帽 Hex Nuts六角重型螺帽 Heavy Hex Nuts薄型螺帽 Hex Jam Nuts尼龙嵌入防松螺帽 Nylon Insert Lock Nuts机械螺丝用六角螺帽 Hex Machine Screw Nut合金钢线材盘元 Alloy Steel Wire Rod球状化线材 Annealing Wire And Rod黑铁丝 Black Wire黄铜棒线 Brass Wire And Rod磨光棒钢 Bright Steel Bar(Hex/Round/Square)铜合金线 Copper Alloy Wire线切割线 E.D.M Cutting Wire快削钢线材盘元 Free Cutting Steel Wire Rod线材 Iron Or Steel Wire线材盘元 Iron Or Steel Wire Rod洋白铜线 Nickel Silver Wire磷青铜线 Phosphate Bronze Wire不锈钢条棒 Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材 Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire不锈钢线材 Stainless Steel Wire不锈钢线材及盘元 Stainless Steel Wire And Rod棒钢 Steel Bar(Hex/Round/Square)转回90度碾线头机 90讧evolving Wire Twisting Machine气动拉钉机 Air Riveter各式螺丝类产品自动包装 Automatic Packaging For All Kinds Of Packaging自动包装机 Automatic Packing Machine螺丝制造搓牙机械 Automatic Thread Rolling Machine螺丝割尾加工机械 Automatic Thread Slotting Machine螺丝制造成型机械 Automatic Trimming Machine拉钉打头机 Blind Rivet Heading Machine螺丝、螺帽成型机 Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理 Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉 Bolt Nut And Screws Heat Treatment Furnaces 球状化电器炖炉 Carburizing Furnace Vacuum And Bell Type Furnace 超防锈复合瓷膜 Ceramic Coating连续式光辉渗碳淬火炉 Continuous Bright Carburizing Quenching Furnace连续式光辉调质淬火炉 Continuous Bright Hardening Quenching Furnace中、高热镀锌光辉连续炉 Continuous Bright Heat Treat Furnace连续式光辉热处理炉 Continuous Type Bright Heat Treatment Furnace 螺丝割尾及特殊割遘加工 Machine Screw Shank Slotting螺丝钻孔加工 Screw Shank Drilling鸡眼上下模 Eyelets Dies一般线材、盘元、退火炉 General Wire,Wire Rod,Annealing Furnace 倒立式滑落型伸线机 Handstand Type Wire Drawing Machine十字冲模 Header Punches In Various Drives成型冲模 Header Punches In Various Drives螺丝打头机 Heading Machine螺丝制造高速搓牙机械 High Speed Automatic Thread Rolling Machine 高中低周波感应加热炉 High,Medium,Low Frequency Induction Heater 空心打头机 Hollow Heading Machine热浸镀锌螺丝、螺帽 Hot Dip Galvanizing Bolts And Nuts机械镀锌 Mechanical Galvanized迷你成型机 Mini-Formers成品自动收线机 Non-Stop Coiler精抽自动收线机 Non-Stop Coiler(Skinpass)螺帽模 Nut Forming Dies螺帽成型模 Nuts Formers特殊零件成型机 Parts Forming Maching冲模 Punch Dies冲子 Punch Pins罗拉成型机 Rollers Formers机(踏)车用螺丝成型机 Screw For Motorcycle Or Bicycle Heading Machine止付螺丝成型机 Set Screws Formers套高成型机 Sockets Formers一般线材、盘元、螺丝合金炖炉 Spheroidizing Bright Annealing Furnace 球状化热处理炉 Spheroidizing Heat Treatment Furnace攻牙机 Tapping Machine螺丝攻、车刀、模具 Taps Dies And Tools搓牙机铁屑分离装置 Thread Chip Separator滚牙轮 Thread Rolling Dies牙板 Thread Rolling Dies Plates精密油压滚牙机 Hydraulic Thread Rolling Machines模具 Tools六角整头模 Trimming Dies Hexagan碳化钨模具 Tungsten Carbide Die镀钛处理(Tin)专业加工服务 Tin Hard Coating For Cutting Tools And Punch By Pvd电镀化学原料 Various Electroplating Chemicals环规校正 Calibration For Ring Gage环规、牙规、三线规校正 Calibration For Ring Gage, Athread Gage, 3 Wire Gage螺丝、螺帽品检量测仪器 Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油 Forming And Tapping Oils For Bolts And Nuts Formers螺丝、螺帽五金等检验 Insptection Services For Fasteners And Hardware德国schatz扭力机代理 Representative Of Schatz Torque Machin Iso品质保证系统 Iso Quality Assurance System生产管理系统 Production Control System物料管理系统 Material Control System齿轮 Gears不锈钢牙条棒 Stainless Steel Hread Rod马达轴承轴心组件 Bearing Shaft(Motor)轴承轴心 Bearing Shaft开口铆钉 Blind Rivets长形拉帽 Blind Rivet Nuts拉帽 Blind Nuts拉钉 Blind Rivets实心梢 Clevis Pins And Straight Pins弹片 Clips卷钉 Coil Nails冷锻零件 Cold Forming Part开口销 Cotter PinsE型环 E-Rings膨胀螺栓 Expansion Anchor Bolts鸡眼钉 Eyelets RivetsR型销 Snap Pins闸、锁 Latches And Keeper Assembleds其它特殊铆钉 Other Specil Rivets销 Pins格式管夹、管束 Pipe Hanger铆钉 Rivets螺旋锔及螺旋圈 Screw Hook And Screw Rings 中空钉 Semi-Tubular Rivet开叉钉 Split Drive Anchors弹簧华司 Spring Washers弹簧蝴蝶夹 Spring Wings不锈钢华司 Stainlesssteel Washers钢铁钉 Steel And Iron Nails搓牙铁钉 Thread Nails钛合金铆钉 Titaium Alloy Rivets管形铆钉 Tubular Rivets华司 Washers真空热处理 Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件 Fasteners合金钢工具 Alloy Steel Tools螺栓模 Bolt Heading Dies手动拉钉钳 Hand Riveter船舶链 Anchor Chain脚踏车链锁 Bicycle Chain Locks螺丝起子 Bit罗拉 Chain Roller特殊铆合扣件 Collars(A Blindfastener For Huck Intl) 装饰链 Decorative Chains自攻螺纹衬套 Ensat Threaded Inserts六角扳手 Hexagon Keys超音螺纹压入式螺纹自动锁扣 Threaded Inserts For Plastic Injection Mouldeings汽车特殊杆接件 Special Auto-Mobile Fastener As Your Needs螺纹护套 Recoil Inserts链条用滚子 Roller For Roller Chain金属板镶嵌组件及自动夹扣组件 Sheet Metal Fasteners工具套筒组件 Socket Wrench Sets不锈钢链 Stainless Steel Chains轭子 T-Yoke轮胎链 Tire Chains狗链 Dog Chains喇叭头轭铁 U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道 Stainless Wheel's Rack For Transporter工业用链 Industrial Steel Link Chains拖链安全链 Tow Chains And Safety Chains机车离合器零件 Manufacture Of Motorcycle's Cvt Parts牙条棒 Thread Rod机(踏)车用螺丝、轴心 Screws And Shafts For Motorcycle Or Bicycle 针车用螺丝、轴心 Screws And Shafts For Sewing Maching止付螺丝 Socket Set Screws不锈钢宽牙螺丝 Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝 Stainless Steel High-Low Thread Screws不锈钢机械螺丝 Stainless Steel Machine Screws不锈钢钻尾螺丝 Stainless Steel Self Drilling Screws不锈钢自攻螺丝 Stainless Steel Self Tapping Screws不锈钢自削螺丝 Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝 Stainless Steel Tri-Lobular Thread Screws MFNI 克叻MFZN 锌Na tural 本色Nikel 叻B-TITE 三角身自攻B型牙P-TITE II 三角身自攻P型双丝牙Nylock 耐落No Nylock 无耐落Case hardness：HV430-530 表面硬度：HV430-530Core hardness：HV210-410 心部硬度：HV210-410Case depth：0.04-0.10mm 渗碳层厚度:0.04-0.10mmProduct compliance with RoHS requirement 产品符合RoHS要求希望以上资料对你有所帮助，附励志名言3条：1、理想的路总是为有信心的人预备着。
(整理)螺丝的国际标准
螺丝的国际标准J-日规（JIS）D-欧规（DIN）A-美规（AISI）G-国标（GB）B-英规（BSW）S-国际标准（ISO）T-特殊标准规格标准——GB标准十字槽盘头自攻螺钉GB 845-85十字槽沉头自攻螺钉GB 846-85十字槽半沉头自攻螺钉GB 847-85开槽盘头自攻螺钉GB 5282-85开槽沉头自攻螺钉GB 5283-85开槽半沉头自攻螺钉GB 5284-85六角头自攻螺钉GB 5285-85十字槽盘头自攻锁紧螺钉GB 6560-86十字槽沉头自攻锁紧螺钉GB 6561-86十字槽半沉头自攻锁紧螺钉GB 6562-86六角头自攻锁紧螺钉GB 6563-86内六角花形圆柱头自攻锁紧螺钉GB 6564-86十字槽头凹穴六角头自攻螺钉GB 9456-88精密机械用紧固件十字槽自攻螺钉刮削端GB /T 13806.2-92墙板自攻螺钉GB /T 14210-93十字槽盘头自钻自攻螺钉GB /T 15856.1-2002十字槽沉头自钻自攻螺钉GB /T 15856.2-2002十字槽半沉头自钻自攻螺钉GB /T 15856.3-2002六角法兰面自钻自攻螺钉GB /T 15856.4-2002六角凸缘自钻自攻螺钉GB /T 15856.5-2002六角凸缘自攻螺钉GB /T 16824.1-1997六角法兰面自攻螺钉GB /T 16824.2-1997规格标准——GB标准十字槽盘头自攻螺钉GB 845-85十字槽沉头自攻螺钉GB 846-85十字槽半沉头自攻螺钉GB 847-85开槽盘头自攻螺钉GB 5282-85开槽沉头自攻螺钉GB 5283-85开槽半沉头自攻螺钉GB 5284-85六角头自攻螺钉GB 5285-85十字槽盘头自攻锁紧螺钉GB 6560-86十字槽沉头自攻锁紧螺钉GB 6561-86十字槽半沉头自攻锁紧螺钉GB 6562-86六角头自攻锁紧螺钉GB 6563-86内六角花形圆柱头自攻锁紧螺钉GB 6564-86十字槽头凹穴六角头自攻螺钉GB 9456-88精密机械用紧固件十字槽自攻螺钉刮削端GB /T 13806.2-92墙板自攻螺钉GB /T 14210-93十字槽盘头自钻自攻螺钉GB /T 15856.1-2002十字槽沉头自钻自攻螺钉GB /T 15856.2-2002十字槽半沉头自钻自攻螺钉GB /T 15856.3-2002六角法兰面自钻自攻螺钉GB /T 15856.4-2002六角凸缘自钻自攻螺钉GB /T 15856.5-2002六角凸缘自攻螺钉GB /T 16824.1-1997六角法兰面自攻螺钉GB /T 16824.2-1997美制螺丝用于机械设备，电子产品，通讯设备，家具设备，建筑行业等行业的生产，安装维修和保养方面．英制6#-32：6#相当于公制的M多少，指螺纹规格；32相当于公制的牙距多少，指一英吋（25.4mm)里面有32个牙距,用25.4除以32即得牙距的公制数字,这个数字便是1个牙距.转载请注明出自六西格玛品质论坛/cdb/,本贴地址:/cdb/viewthread.php?tid=178182螺钉的性能与等级划分国际标准管理提醒：本帖被chenmiaooo 执行锁定操作(2008-09-23)1）.钢结构连接用螺栓性能等级分3.6、4.6、4.8、5.6、6.8、8.8、9.8、10.9、12.9等10余个等级。
螺栓中英文对照
螺栓中英文对照:六角螺丝(栓) HEX HEAD CAP SCREWS（HEX BOLTS）六角机械螺丝HEX HEAD MACHINE BOLTS六角木牙螺丝HEX LAG BOLTS四角螺丝SQUARE HEAD BOLTST头螺丝T HEAD BOLTS马车螺丝CARRIAGE BOLTS环首螺丝EYE BOLTS内六角孔螺丝HEX SOCKET CAP SCREWS固定螺丝SET SCREWS螺椿栓STUD BOLTS螺旋椿SCREW STUDS轮壳螺栓WHEEL BOLTS翼形螺丝WING SCREWS自攻螺丝SELF TAPPING SCREWS自削螺丝THREAD CUTTING SCREWS钻尾螺丝SELF DRILLING SCREWS旋入螺丝DRIVE SCREWS机械螺丝MACHINE SCREWS木螺丝WOOD SCREWS家具螺丝FURNITURE SCREWS塑板螺丝CHIPBOARD SCREWS墙用螺丝DRYWALL SCREWS基础螺栓FOUNDATION BOLTSU型螺栓U BOLTS勾头螺栓HOOK BOLTS套挂螺丝TOGGLE BOLTS突缘螺丝FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS耐候钢螺丝CORTEN STEEL HEAVY HEX BOLTS扭矩控制螺栓T.C。
BOLTS高张力螺栓HIGH STRENGTH BOLTS剪力钉(焊接螺丝）WELDING STUDS螺丝附华司组合SCREWS AND WASHERS ASSEMBLED(SEMS）大尺寸螺栓BIG SIZE BOLTS不锈钢小螺丝STAINLESS STEEL SHEET METAL SCREWS不锈钢大螺丝STAINLESS STEEL BOLTS铜螺丝BRASS SCREWS铝螺丝ALUMINUM SCREWS合金钢螺丝ALLOY STEEL SCREWS电子螺丝ELECTRONIC SCREWS微小精密螺丝MICRO SCREWS塑胶螺丝PLASTIC SCREWS复合材料用螺丝PARTICLE BOARD SCREWS钛合金螺丝TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料TI,ZR,MO,NB PARE METAL BOLTS PARTS拇指螺丝THUMB SCREWS双头牙螺丝DOUBLE END SCREWS HANGER BOLT车辆（汽车)螺丝、螺帽AUTOMOTIVE FASTENERS航太用螺丝AEROSPACE FASTENERS飞机特殊扣件SOURCE CONTROL BOLTS拉栓BLIND BOLTS面板螺丝PANEL FASTENERS电梯螺丝ELEVATOR BOLTS四角头固定螺丝SQUARE SET SCREWS大头马车螺丝STEP BOLTS单向螺丝ONE WAY LAG SCREWS管夹螺丝HOSE CLAMP SCREWS不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝HINGE SCREWS货柜螺丝CONTAINER SCREWS复合材料钻尾螺丝BI—METAL SELF DRILLING SCREWS三角牙螺丝TRILOBULAR THREAD SCREWS高低牙螺丝HIGH LOW SCREWS夹板用螺丝PARTICLE BOARD SCREWS马桶螺丝TOILET CLOSET BOLTS特长螺丝SPECIAL LONGER SCREWS建业螺丝BUILDING FASTENERS其它特殊螺丝SPECIAL SCREWS OR BOLTS不锈钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS宽牙螺丝（粗牙螺丝）COARSE THREAD SCREWS链带螺丝COLLATED SCREWS水泥螺丝CONCRETE SCREWS板模螺丝CONSTRUCTION BOLTS涞□萁z DIE CAST WING SCREWS；ZINC ALLOY重型车螺丝HEAVY DUTY WHEEL HUB BOLTS内六角固定螺丝HEX SOCKET SET SCREWS复合材料用螺丝（夹板用）PARTICLE BOARD SCREWS犁壁螺丝PLOW BOLTS机（踏)车用螺丝、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺丝、轴心SCREWS AND SHAFTS FOR SEWING MACHING止付螺丝SOCKET SET SCREWS不锈钢宽牙螺丝STAINLESS STEEL COARSE THREAD SCREWS不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS不锈钢三角牙螺丝STAINLESS STEEL TRI—LOBULAR THREAD SCREWS 不锈钢木螺丝STAINLESS STEEL WOOD SCREWS套挂螺栓及螺丝TOGGLE BOLTS钛合金膨胀螺丝TITANIUM ALLOY EXPANSION BOLTSNo. 单词简写中文1 screw scr 螺丝CSK screw 埋头螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头Hexagon hex(a）六角High Control H.C。
螺栓中英文对照
螺栓中英文对照:六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS）六角机械螺丝HEX HEAD MACHINE BOLTS六角木牙螺丝HEX LAG BOLTS四角螺丝SQUARE HEAD BOLTST头螺丝T HEAD BOLTS马车螺丝CARRIAGE BOLTS环首螺丝EYE BOLTS内六角孔螺丝HEX SOCKET CAP SCREWS固定螺丝SET SCREWS螺椿栓STUD BOLTS螺旋椿SCREW STUDS轮壳螺栓WHEEL BOLTS翼形螺丝WING SCREWS自攻螺丝SELF TAPPING SCREWS自削螺丝THREAD CUTTING SCREWS钻尾螺丝SELF DRILLING SCREWS旋入螺丝DRIVE SCREWS机械螺丝MACHINE SCREWS木螺丝WOOD SCREWS家具螺丝FURNITURE SCREWS塑板螺丝CHIPBOARD SCREWS墙用螺丝DRYWALL SCREWS基础螺栓FOUNDATION BOLTSU型螺栓U BOLTS勾头螺栓HOOK BOLTS套挂螺丝TOGGLE BOLTS突缘螺丝FLANGE BOLTS轨道螺栓(鱼尾螺丝）TRACK BOLTS耐候钢螺丝CORTEN STEEL HEAVY HEX BOLTS扭矩控制螺栓T。
C。
BOLTS高张力螺栓HIGH STRENGTH BOLTS剪力钉（焊接螺丝) WELDING STUDS螺丝附华司组合SCREWS AND WASHERS ASSEMBLED（SEMS) 大尺寸螺栓BIG SIZE BOLTS不锈钢小螺丝STAINLESS STEEL SHEET METAL SCREWS不锈钢大螺丝STAINLESS STEEL BOLTS铜螺丝BRASS SCREWS铝螺丝ALUMINUM SCREWS合金钢螺丝ALLOY STEEL SCREWS电子螺丝ELECTRONIC SCREWS微小精密螺丝MICRO SCREWS塑胶螺丝PLASTIC SCREWS复合材料用螺丝PARTICLE BOARD SCREWS钛合金螺丝TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料TI，ZR，MO,NB PARE METAL BOLTS PARTS 拇指螺丝THUMB SCREWS双头牙螺丝DOUBLE END SCREWS HANGER BOLT车辆（汽车)螺丝、螺帽AUTOMOTIVE FASTENERS航太用螺丝AEROSPACE FASTENERS飞机特殊扣件SOURCE CONTROL BOLTS拉栓BLIND BOLTS面板螺丝PANEL FASTENERS电梯螺丝ELEVATOR BOLTS四角头固定螺丝SQUARE SET SCREWS大头马车螺丝STEP BOLTS单向螺丝ONE WAY LAG SCREWS管夹螺丝HOSE CLAMP SCREWS不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝HINGE SCREWS货柜螺丝CONTAINER SCREWS复合材料钻尾螺丝BI—METAL SELF DRILLING SCREWS三角牙螺丝TRILOBULAR THREAD SCREWS高低牙螺丝HIGH LOW SCREWS夹板用螺丝PARTICLE BOARD SCREWS马桶螺丝TOILET CLOSET BOLTS特长螺丝SPECIAL LONGER SCREWS建业螺丝BUILDING FASTENERS其它特殊螺丝SPECIAL SCREWS OR BOLTS不锈钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS宽牙螺丝(粗牙螺丝）COARSE THREAD SCREWS链带螺丝COLLATED SCREWS水泥螺丝CONCRETE SCREWS板模螺丝CONSTRUCTION BOLTS涞□萁z DIE CAST WING SCREWS; ZINC ALLOY重型车螺丝HEAVY DUTY WHEEL HUB BOLTS内六角固定螺丝HEX SOCKET SET SCREWS复合材料用螺丝（夹板用) PARTICLE BOARD SCREWS犁壁螺丝PLOW BOLTS机（踏)车用螺丝、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺丝、轴心SCREWS AND SHAFTS FOR SEWING MACHING止付螺丝SOCKET SET SCREWS不锈钢宽牙螺丝STAINLESS STEEL COARSE THREAD SCREWS不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS不锈钢三角牙螺丝STAINLESS STEEL TRI—LOBULAR THREAD SCREWS 不锈钢木螺丝STAINLESS STEEL WOOD SCREWS套挂螺栓及螺丝TOGGLE BOLTS钛合金膨胀螺丝TITANIUM ALLOY EXPANSION BOLTSNo。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
ISO299
59
DIN551
ISO4776
60 61 62 63 64
DIN553 DIN555 DIN557 DIN558 DIN561
65
DIN562
slotted set 开槽锥端紧定螺钉 screws with cone point 六角螺母 hexagon nuts 方螺母-C square nuts 六角头螺钉 hexagon screws hexagon set 六角头圆柱端紧定螺 screws with full 钉 dog point square nuts without 薄型方螺母-B bevel(pressed nuts)
ISO7434 ISO4034 ISO4018
66 67 68 69 70
DIN571 DIN580 DIN582 DIN601 DIN603
六角头木螺钉 吊环螺钉 吊环螺母 六角头螺栓 大半圆头方颈螺栓(马 车螺栓) 沉头带插销马车螺栓 沉头长方颈马车螺栓 半圆头带插销马车螺 栓 沉头短方颈马车螺栓 六角头精配螺栓（长 螺纹） 六角头精配螺栓（短 螺纹） 滚花平头螺钉 半圆头铆钉 沉头铆钉 半沉头铆钉 大扁头铆钉
94
DIN914
内六角尖端紧定螺钉 内六角圆柱端紧定螺 钉 内六角凹端紧定螺钉 薄型盲螺母 开槽小圆柱头螺钉
ISO4027
95
DIN915
ISO4028
96 97 98
DIN916 DIN917 DIN920
ISO4029
99
DIN921
开槽大圆柱头螺钉
100 101 102 103 104
DIN923 DIN927 DIN928 DIN929 DIN931
slotted knurled 开槽滚花高头螺钉 thumb screws with collar knurled thumb 滚花高螺母 nuts with collar knurled thumb 滚花薄螺母 thin nuts 锁紧垫圈 sealing washers retaining rings for 轴用弹性挡圈 shafts(external),c irclips retaining rings for 孔用弹性挡圈 bores(internal),ci rclips square head 方头带垫螺栓 bolts with collar square head 方头圆柱底端螺栓 bolts with half dog point square head bolts with 方头带垫半圆底端螺 collar,half dog 栓 point and rounded end T型槽螺母 T-slot nuts 单头螺柱 single end studs 地脚螺栓 masonry bolts slotted round 带槽圆螺母 nuts round nuts with 端面带孔圆螺母 drilled holes in one face 开槽平端紧定螺钉 slotted sit screws with flat point
DIN127-B DIN128-A DIN137-A DIN137-B DIN186 DIN188 DIN258 DIN261
22 23 24 25 26 27 28
DIN315AF DIN315DF DIN316AF DIN317DF DIN319 DIN404 DIN417
ቤተ መጻሕፍቲ ባይዱ
蝶型螺母(美制) 蝶型螺母(德制) 蝶型螺钉(美制) 蝶型螺钉(德制) 圆球型盖型螺母 开槽带孔球面圆柱头 螺钉 开槽长圆柱端紧定螺 钉 开槽平端紧定螺钉(半 牙) 小六角特薄细牙螺母 外舌止动垫圈 小垫圈(用于圆柱头螺 钉) 方斜垫圈(U型)
29 30 31 32
DIN427 DIN431 DIN432 DIN433
33
DIN434
34 35 36 37 38 39
DIN435 DIN436 DIN438 DIN439 DIN439 DIN440
方斜垫圈(I型) 方垫圈 开槽凹端紧定螺钉 六角薄螺母 细牙六角薄螺母 木螺钉专用垫圈
40 41 42 43 44
71 72 73 74 75 76 77 78 79 80 81
DIN604 DIN605 DIN607 DIN608 DIN609 DIN610 DIN653 DIN660 DIN661 DIN662 DIN674
82
DIN703
重型侧面带孔圆螺母
83 84 85 86
DIN705 DIN741 DIN787 DIN835
侧面带孔圆螺母 卡头 T型槽螺钉 双头螺柱（牙长 =2D）
hexagon head wood screws (coach screws) lifting eye bolts lifting eye nuts hexagon bolts mushroom head square neck bolts (carriage bolts) flat countersunk nib bolts flat countersunk long square neck bolts cup head nib bolts flat countersunk short square neck bolts hexagon fitted bolts,long thread hexagon fitted bolts,short thread knurled thumb screws thin type round head rivets contersunk head rivets raised contersunk head rivets mushroom head rivets adjusting rings,heavy range (shafting collars) adjusting rings,light range (shafting collars) wire rope clips T-slot screws studs-metal (end=2d)
外六角直型闭锁螺钉 内六角扳手 内六角圆柱头螺钉 内六角平端紧定螺钉
hexagon socket pipe plugs,conical thread hexagon socket screw plugs,cyl. thread hexagon head pipe plugs,conical thread hexagon head screw plugs,cyl.thread socket wrenches hexagon socket cap screws hexagon socket set screws with flat point hexagon socket set screws with cone point hexagon socket set screws with dog point hexagon socket set screws with cup point hexagon cap nuts slotted short cheese head screws slotted large cheese head screws slotted pan head screws with shoulder slotted shoulder screws square weld nuts hexagon weld nuts hexagon head screws ISO2936 ISO4762 ISO4026
7月5日
德国标准和国际标准、中国标准中英文对照表
德国标准和国际标准、中国标准中英文对照表 中文品名 英文品名 国际标准 Description in Description in ISO-Standard Chinese English 圆锥销 taper pins ISO2339 圆柱销 parallel pins ISO2338 slotted cheese 开槽圆柱头螺钉 ISO1207 head screws slotted pan head 开槽盘头螺钉 ISO1580 screws 单耳止动垫圈 tab washers 开口销 split cotter pins ISO1234 slotted raised 开槽半沉头木螺钉 csk head wood screws slotted round 开槽半圆头木螺钉 head wood screws slotted countersunk 开槽沉头木螺钉 head wood screws 平垫 plain washers ISO7089 平垫(带倒角) mediun washers ISO7090 平垫 plain washers ISO7091 spring lock 重型弹垫 washers,tang ends spring lock 标准弹垫 washers,square ends single coil spring 鞍形弹垫 lock washers curved spring 弹簧止动垫圈 washers wave spring 波形弹垫 washers T-head bolts with T型方颈螺栓 square neck T-head bolts with T型双接头螺栓 double nip taper pins with 螺纹圆锥销 ISO8737 threaded end T型头螺栓 T-head bolts
DIN443 DIN444 DIN462 DIN463 DIN464
密封帽 活节螺栓B 型 内舌止动垫圈 双耳止动垫圈 滚花高头螺钉
wing nuts amercia form wing nuts germany form wing screws amercia form wing screws germany form ball knobs slotted capstan screws slotted set srews with full dog point slotted set srews with chamfered end pipe nuts with thread external tap washers for cheese head screws square taper washers for Usection square taper washers for Isections square washers slotted set with cup point hexagon thin nuts hexagon thin nuts rounds washers for wood constructions sealing caps,push-in type eye bolts form B internal tab washers washers with two taps knurled thumb screws with collar