聚合物锂电池 YJ802040-600MAH 普通板规格书
聚合物锂离子电池产品规格书说明书
Product Specification for Li-ion Polymer Battery 聚合物锂离子电池产品规格书Model电芯型号: 702427(PCM)惠州基安比新能源有限公司HUIZHOU MARKYN NEW ENERGY CO.,LTD.电话: ************传真: ************TEL: ************ FAX : ************SPECIFICATION AMENDMENT RECORDS规格书变更记录1. Scope适用范围：This document describes the Product Specification of the Li-Polymer Rechargeable Battery supplied by Huizhou Markyn New Energy Co., LTD.本规格书描述了惠州基安比新能源有限公司的可充电锂离子聚合物电池的产品性能指标。
2. Description 说明2.1 Description: Li-Polymer Battery类型：锂离子聚合物电池2.2 Model: 702427型号：7024273. Specification产品规格4. Battery Cell Performance Criteria 电芯性能标准4.1 Standard testing environment标准测试环境Unless specifically stated otherwise, tests must be done within one month of delivery and the number of charging-recharging cycles is fewer than 5. The following is test conditions:Test conditions:Ambient Temperature：23ºC ± 2ºCAmbient Humidity：65±20%RH除非另有说明，测试应在电池出货的1个月内进行，且充放电循环的次数少于5次。
锂电池规格书参照
聚合物锂离子电池产品规格承认书：：JD220768430F（500Ah）品名：品名编制审核批准客户确认签名//日期客户名称//印章签名客户名称总部：北京神州巨电新能源技术开发有限公司Beijing Globe Super Power New Energy Technology Development Corp.地址：中国北京市海淀区上地3街9号嘉华大厦E座206ADD:Rm E-206,Gem Tech-Center,No.9,3rd Street,Haidian Dist.,Beijing,P.R.China 86-10--82783543-816Fax:86-1086-10--82780720-1073Tel:86-10工厂：河北神州巨电新能源科技开发有限公司Hebei Globe Super Power New Energy Technology Development Corp.地址：河北邢台市巨鹿县巨鹿工业园Hebei i Province,P.R.ChinaADD:Industrial District,Ju Jul l u,Xiangtan,Hebe产品规格承认书目录1.适用范围---------------------------------------------------------------------------------------------------------22.产品规格---------------------------------------------------------------------------------------------------23.电池性能检查测试-----------------------------------------------------------------------------------------24.外观尺寸图------------------------------------------------------------------------------------------------------35.使用指南--------------------------------------------------------------------------------------------------------36.其它事项------------------------------------------------------------------------------------------------------47.电芯处理须知---------------------------------------------------------------------------------------------------41.使用范围本规格书仅适用于巨电新能源制造的聚合物锂电池，型号JD220768430F.2.产品规格序号项目规格备注1充电电压 3.65V2标称电压 3.2V出货状态,电压为3.1V~3.3V.3标称容量500Ah容量是指标准充电后,0.2C放电到2.5V截止电压所放出的容量.平均容量520Ah最低容量500Ah4循环寿命≥2000每圈循环是以250A的电流充放到截止电压为2.5V的间歇过程.当放电容量降至初始容量的80%时,所完成的循环圈数定义为该电芯的循环寿命5自放电剩余容量>90%该容量是指标准充电后,在23°C±2°环境下贮存30天,以No.3的条件下所测得的容量.6内阻≤2mohm标准充电后,在AC1KHz条件下测量的交流阻抗. 7最大充电电流1C(500A)8最大放电电流1C(500A)9放电截止电压 2.5V10工作温度放电状态:-20°C~+60°C充电状态:0°C~+45°C贮存状态:-20°C~+45°C贮存电压为3.1V~3.3V.若需长时间存放,每隔90天需将电芯充放电一次.11温度特性60ºC@0.2C:98%23ºC@0.2C:100%-20ºC@0.2C:75%电池标准充电后,在测试温度下搁置4小时，然后在测试温度条件下以0.2C恒流放电至2.0V时所放出来的容量与在标准温度23°C±2°C)放电容量之比12净重约15kg13外型尺寸长：470.0mm Max宽：785.0mm Max厚：23.0mm Max不包括极耳3.电池性能检查测试3.1外观检查电芯表观应完整,不允许有刮痕,褶皱,裂纹,漏液等会导致电芯性能损坏的缺陷.3.2标准测试环境除非特别说明，本产品规格书中的所有测试均在以下环境条件下进行：温度：23°C±2°C湿度：65±20%3.3充放电方法和条件序号项目测试方法及条件1充电电流标准充电电流：0.2C(100A)快速充电电流：1C(500A)2标准充电先用0.2C(100A)恒流充电至3.65V,再用3.65V恒压(精度3.65±0.05V)充电至电流0.02C(10.0A)。
Li-ionPolymerBatterySpecification锂离子聚合物电池规格书
电芯容量：Customer Code：9深圳市红达科电子有限公司Shenzhen Hondark Electronics Co. Ltd.Li-ion Polymer BatterySpecification锂离子聚合物电池规格书电芯型号：Cell Capacity：文件页数：290mAhAdd：Cell Model：TY552325客户代码：Total Page：地址：中国，深圳市宝安区龙华大浪羊台山和发兴工业园1楼File No. /文件编号：TY-JS-SP-A107版本REV：A0Cover Page深圳市红达科电子有限公司Shenzhen Hondark Electronics Co. Ltd.Content目录Page1.Modified List 修订履历12.Scope 适用范围23. Initial Dimension 初始尺寸24. Specification 产品规格35.General Performance 常规性能46.Environment Performance 环境性能47.Safe Characteristic 安全性能58.Protection Circuit 保护电路59.Warnings 警告710.Cautions 注意711.Handling of Cells 电池操作注意事项812.Period of Warranty 保质期813.Others 其他事项81.Modified List 修订履历Product Modified Record List产品变更履历表2. 3.Scope 适用范围This specification describes the basic performance, technical requirement, testing method, warning and caution of the Li-ion Polymer rechargeable battery pack, the pack defined in this documentation is an assembly which include battery, PCM and wire, the specification only applies to Shenzhen Better Power technology Co. , Ltd本标准规定了锂离子聚合物可充电电池的基本性能、技术要求、测试方法及注意事项，电池组合定义的是包括电芯，保护板和连接线的组合，本标准只是用于红达科科技有限公司所生产的电芯。
锂离子聚合物电池规格书说明书
页码：1/15602030PL300mAhSpecification of Li-ion Rechargeable Battery锂离子电池规格书Model：602030PL300mAh/3.7VCustomer Confirmation Customer Name: Customer No.: Comment:Customer Approval:Prepared by Checked by Approved by 肖志军602030PL300mAh页码：2/15兴永恒（深圳）电子有限公司深圳宝安区沙井后亭E-mail：****************Website：TEL：86-0755-********FAX：86-0755-********AMENDMENT RECORDSREVISION DATE ORIGINATOR REASON FOR REVISION A001 2016-6-20602030PL300mAh页码：3/15Content目录1. Scope范围 (4)2. Reference Standard 参考标准 (4)3. Picture of battery电池图 (4)3.1 Picture of single cell 单体电芯图 (4)3.2 Picture of assembled battery 组合电池图 (6)4. Basic of performance 基本性能 (7)4.1 Single cell parameters 单体电芯参数 (7)4.2 Assembled cell parameters包装后电芯组参数 (8)5. Electrical Characteristics电性能 (8)5.1 Normal Test Conditions标准测试条件 (8)5.2 Electrochemical Characteristics电化学性能 (8)5.3 Environment Characteristics环境适应性能 (9)5.4 Safety Characteristics 安全性能 (10)6. PCM Specification PCM 规格 (11)6.1 Electrical Characteristics电性能 (11)6.2 Circuit Diagram 电路图 (11)6.3 Circuit topology Drawing and PIN Explanation电路布线图和焊盘说明 (12)6.4 PCM BOM 保护板物料清单 (12)7. Storage and Shipment Requirement存储及运输要求 (13)8. Warning and Cautions 警告及注意事项 (13)9. Note 声明 (15)页码：4/15602030PL300mAh1. Scope范围This specification describes the performance, testing method, warning and caution of the lithium-ion rechargeable battery.The specification applies to polymer battery supplied by Shenzhen biyate energy co., ltd本标准描述了锂离子电池的性能、测试方法及注意事项。
聚合物锂电池 规格
聚合物锂电池规格
聚合物锂电池规格
聚合物锂电池是一种新型的锂离子电池，具有高能量密度、轻量化、安全性好等优点，因此广泛应用于移动电源、智能手环、智能手表等电子产品中。
在选购聚合物锂电池时，需要了解其规格，下面列举一些常见的规格：
1. 电压：聚合物锂电池的标准电压为3.7V，也有一些规格为3.8V或3.2V。
2. 容量：容量是指电池储存电能的能力，单位为毫安时（mAh）。
聚合物锂电池的容量一般在100mAh到5000mAh之间，不同规格的电池容量不同，用户可以根据需要选择。
3. 尺寸：聚合物锂电池的尺寸也是选购时需要考虑的因素之一。
常见的尺寸有401020、501225、602030、103450等，不同尺寸的电池适用于不同的设备。
4. 放电倍率：放电倍率是指电池在一定时间内释放电能的速度，单位为C。
聚合物锂电池的放电倍率一般在1C到10C之间，不同倍率的电池适用于不同的设备。
5. 工作温度：聚合物锂电池的工作温度一般在-20℃到60℃之间，不同温度下电池的性能会有所不同，用户需要根据使用环境选择合适的规格。
总之，选购聚合物锂电池时需要考虑电压、容量、尺寸、放电倍率和工作温度等因素，选择合适的规格可以提高电池的使用效果和寿命。
聚合物锂电池规格表
版 本制定日期页 次1222441150140180 3.7 3.5±0.52263030200190130 3.74±1330153310095300 3.72±14301550170160200 3.7 3.4±0.55302029140130200 3.7 2.8±0.56302025110100270 3.7 2.8±0.57302040190185140 3.7 3.8±0.58302222105100300 3.7 2.1±0.59302236190190150 3.7 3.8±0.510302248260260100 3.7 5.2±0.511302425150140200 3.73±0.5123007457070380 3.7 1.4±0.51330074565380 3.7 1.3±0.514302323120120250 3.7 2.4±0.515302535210200140 3.7 4.2±0.516302540230230120 3.7 4.6±0.517302626150140200 3.73±118303040310310100 3.7 6.2±0.51930304840040090 3.78±12030345050050070 3.710±12130346060060060 3.712±12233344850070 3.710±12333346265065060 3.713±124303535310310100 3.7 6.2±12530404550049070 3.710±12630436068068045 3.713.6±1273245100140060 3.728±1283512205045450 3.7 1.5±0.5293514279090270 3.7 1.8±0.530352025********* 3.7 2.6±0.531353035********* 3.7 6.2±1323565852000195040 3.738±13336132070350 3.7 1.4±13437515295095045 3.719±135381429130240 3.7 2.6±13638345065065060 3.713±13.20-0.3 *45.0+0.5-0.5 *100.5+0.5-0.53.80.2-0.3 *14.0+0.5-0.5 *29.0+0.5-0.5A 2009-12-09PAGE 1 OF 63.90-0.3 *13.0+0.5-0.5 *20.0+0.5-0.53.80-0.3 *34.0+0.5-0.5 *50.0+0.5-0.53.50-0.3 *14.0+0.5-0.5 *27.0+0.5-0.53.50-0.3 *65.0+0.5-0.5 *85.0+0.5-0.53.10-0.3 *34.0+0.5-0.5 *50.0+0.5-0.53.00-0.3 *34.0+0.5-0.5 *59.0+0.5-0.53.30-0.3 *34.0+0.5-0.5 *61.0+0.5-0.53.10-0.3 *40.0+0.5-0.5 *45.0+0-0.5深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY TECHNOLOGY CO., LTD.尺寸(mm)序号最小容量（mAh） 3.70-0.3 *51.0+0.5-0.5 *52.0+0.5-0.53.10-0.3 *30.0+0.5-0.5 *48.0+0.5-0.5量产规格表3.10-0.3 *43.0+0.5-0.5 *60.0+0.5-0.53.50-0.3 *20.0+0.5-0.5 *25.0+0.5-0.53.50-0.3 *30.0+0.5-0.5 *35.0+0.5-0.5内阻（mΩ）标称容量（mAh）型号 3.10-0.3 *15.0+0.5-0.5 *50.0+0.5-0.53.10-0.3 *20.0+0.5-0.5 *29.0+0.5-0.53.10-0.3 *20.0+0.5-0.5 *25.0+0.5-0.53.10.1-0.3 *20.0+0.5-0.5 *40.0+0.5-0.53.00.3-0.3 *7.0+1.5-0.5 *45.0+0.5-0.53.10-0.3 *25.0+0.5-0.5 *35.0+0.5-0.53.10-0.3 *22.0+0.5-0.5 *36.0+0.5-0.5电压（V）重量（g)厚×宽×高2.750-0.3 *30.0+0.5-0.5 *30.0+0.5-0.52.20-0.3 *24.0+0.5-0.5 *41.0+0.5-0.53.10-0.3 *30.0+0.5-0.5 *40.0+0.5-0.53.10-0.3 *15.0+0.5-0.5 *33.0+0.5-0.53.10-0.3 *35.0+0.5-0.5 *35.0+0.5-0.53.10-0.3 *22.0+0.5-0.5 *48.0+0.5-0.53.10-0.3 *25.0+0.5-0.5 *40.0+0.5-0.53.10-0.3 *26.0+0.5-0.5 *26.0+0.5-0.53.10.1-0.3 *23.0+0.5-0.5 *23.0+0.5-0.53.50-0.3 *12.0+0.5-0.5 *20.0+0.5-0.53.30-0.3 *34.0+0.5-0.5 *48+0.5-0.53.10-0.3 *22.0+0.5-0.5 *22.0+0.5-0.53.20-0.3 *24.0+0.5-0.5 *25.0+0.5-0.53.00.3-0.3 *7.0+1.0-0.5 *45.0+0.5-0.5版 本制定日期页 次3738364155055070 3.711±13838112580330 3.7 1.6±13940103080330 3.7 1.5±0.5404011174040600 3.7 1.5±0.5414011206060430 3.72±0.5424012258075330 3.72±0.543401229100100300 3.72±0.544401235120120200 3.7 2.4±0.545401429120120200 3.7 2.4±0.546401445200200130 3.74±0.547401525110240 3.7 2.2±0.548401730160160180 3.7 3.2±0.549402020110110240 3.7 2.2±0.550402023130120200 3.7 2.6±0.551402025150145180 3.73±0.552402030190190130 3.7 3.8±0.553402035220220130 3.7 4.4±0.554402040280260100 3.7 5.6±155402535300300100 3.76±15640254034034090 3.7 6.8±157402626210210130 3.7 4.2±15840304046046070 3.79.2±15940304858058060 3.711.6±16040344050050070 3.710±16140345068068060 3.713.6±16240471082000200040 3.738±1634215155550420 3.7 1.1±0.5644315178080350 3.7 1.6±0.5654411206060380 3.7 1.2±0.56645102780330 3.7 1.6±0.5674511154040500 3.71±0.5684511175050500 3.71±0.56945121760430 3.71±0.5704512207070350 3.7 1.8±0.571451225100100300 3.72±0.572451235130200 3.7 2.6±0.54.00-0.3 *15.0+0.5-0.5 *25.0+0.5-0.54.00-0.3 *12.0+0.5-0.5 *35.0+0.5-0.54.00-0.3 *14.0+0.5-0.5 *29.0+0.5-0.54.00-0.3 *12.0+0.5-0.5 *29.0+0.5-0.54.00-0.3 *11.0+0.0-0.5 *17.0+0.5-0.53.80-0.3 *11.0+1.0-0.5 *25+0.5-0.54.00-0.3 *10.0+0.7-0.5 *30+0.5-0.54.00-0.3 *20.0+0.5-0.5 *30.0+0.5-0.54.00-0.3 *12.0+0.5-0.5 *25.0+0.5-0.54.50-0.3 *12.0+0.5-0.5 *35.0+0.5-0.54.00-0.3 *34.0+0.5-0.5 *40.0+0.5-0.54.00-0.3 *47.0+0.5-0.5 *108.0+0.5-0.54.00-0.3 *11.0+0.0-0.5 *20.0+0.5-0.5厚×宽×高内阻（mΩ）最小容量（mAh）A 2009-12-09PAGE 2 OF 6电压（V）重量（g)量产规格表序号型号标称容量（mAh） 4.00-0.3 *20.0+0.5-0.5 *40.0+0.5-0.54.00-0.3 *34.0+0.5-0.5 *50.0+0.5-0.54.50-0.3 *12.0+0.5-0.5 *20.0+0.5-0.54.50-0.3 *10.0+0.5-0.5 *27.0+0.5-0.54.20-0.3 *15.0+0.5-0.5 *15.0+0.5-0.54.30.2-0.3 *15.0+0.5-0.5 *17.0+0.5-0.54.50-0.3 *11.0+0-0.5 *17.0+0.5-0.54.50-0.3 *12.0+0.5-0.5 *25.0+0.5-0.54.40-0.3 *11.0+0.5-0.5 *20.0+0.5-0.54.00-0.3 *25.0+0.5-0.5 *35.0+0.5-0.54.00.1-0.3 *26.0+0.5-0.5 *26.0+0.5-0.54.00-0.3 *30.0+0.5-0.5 *40.0+0.5-0.54.00-0.3 *30.0+0.5-0.5 *48.0+0.5-0.54.00-0.3 *25.0+0.5-0.5 *40.0+0.5-0.54.00-0.3 *20.0+0.5-0.5 *25.0+0.5-0.54.00-0.3 *20.0+0.5-0.5 *35.0+0.5-0.54.00-0.3 *17.0+0.5-0.5 *30.0+0.5-0.53.80-0.3 *36.0+0.5-0.5 *41.0+0.5-0.5深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY TECHNOLOGY CO., LTD.尺寸(mm)4.50-0.3 *12.0+0.5-0.5 *17.0+0.5-0.54.50-0.3 *11.0+0.5-0.5 *15.0+0.5-0.54.00-0.3 *20.0+0.5-0.5 *20.0+0.5-0.54.00-0.3 *20.0+0.5-0.5 *23.0+0.5-0.54.00-0.3 *14.0+0.5-0.5 *45.0+0.5-0.57345151880330 3.7 1.6±0.574452030********* 3.7 4.4±0.575452626********* 3.7 4.6±0.57645283742042080 3.78.4±0.5774538751450145040 3.729±0.5784538851650165035 3.733±0.5794538901800180035 3.736±0.580459555150140180 3.73±0.5814540851700170035 3.734±1824550601400140045 3.728±1834555601700170045 3.734±1844562712250225045 3.743±185471630180170180 3.7 3.6±0.5864808184038550 3.71±0.387481135140140200 3.73±1884812208075330 3.7 1.6±0.589481520100300 3.72±0.590481525130125220 3.7 2.6±0.591482020130125220 3.7 2.6±0.592501230********* 3.7 2.6±0.593501235150150200 3.73±0.594501430150150200 3.73±0.595501621110240 2.296501730********* 3.7 4.2±0.597501735260260130 3.7 5.2±0.598502025200200140 3.74±0.599502030250250120 3.75±0.510050203530030090 3.76±110150273035035080 3.77±110250303038038080 3.77.6±110350313045045080 3.79±110450304058058070 3.711.6±110550304872072045 3.714.4±110650344065065060 3.713±11075035621100110045 3.722±11085037591100110045 3.722±15.00-0.3 *37.0+0.5-0.5 *59.0+0.5-0.55.00-0.3 *30.0+0.5-0.5 *40.0+0.5-0.55.00-0.3 *30.0+0.5-0.5 *48.0+0.5-0.54.50-0.3 *9.0+0.5-0.5 *55.0+0.5-0.54.50-0.3 *38.0+0.5-0.5 *90.0+1.0-0.54.50-0.3 *15.0+0.5-0.5 *18.0+0.5-0.55.00-0.3 *34.0+0.5-0.5 *40.0+0.5-0.54.70-0.3 *16.0+0.5-0.5 *30.0+0.5-0.54.50-0.3 *55.0+0.5-0.5 *60.0+0.5-0.54.50-0.3 *41.5+0.5-0.5 *85.0+0.5-0.55.00-0.3 *12.0+0.5-0.5 *29.0+0.5-0.55.00-0.3 *12.0+0.5-0.5 *35.0+0.5-0.55.00-0.3 *30.0+0.5-0.5 *30.0+0.5-0.55.00-0.3 *31.0+0.5-0.5 *30.0+0.5-0.54.50-0.3 *20.0+0.5-0.5 *30.0+0.5-0.54.80-0.3 *11.0+0.5-0.5 *34.0+0.5-0.54.50-0.3 *62.0+0.5-0.5 *71.0+0.5-0.54.50-0.3 *50.0+0.5-0.5 *60.0+0.5-0.54.50-0.3 *26.0+0.5-0.5 *26.0+0.5-0.55.80-0.3 *8.0+0.5-0.5 *20.0+0.5-0.54.80-0.3 *11.5.0+0.5-0.5 *20.0+0.5-0.54.80-0.3 *15.0+0.5-0.5 *25.0+0.5-0.54.80-0.3 *20.0+0.5-0.5 *20.0+0.5-0.5尺寸(mm)5.00.1-0.3 *17.0+0.5-0.5 *34.0+0.5-0.54.80-0.3 *15.0+0.5-0.5 *20.0+0.5-0.54.50-0.3 *28.0+0.5-0.5 *37.0+0.5-0.54.50-0.3 *38.0+0.5-0.5 *85.0+0.5-0.54.50-0.3 *38.0+0.5-0.5 *75.0+0.5-0.55.00-0.3 *14.0+0.5-0.5 *29.0+0.5-0.55.00-0.3 *17.0+0.5-0.5 *30.0+0.5-0.5量产规格表序号型号标称容量（mAh）内阻（mΩ）电压（V）重量（g)厚×宽×高最小容量（mAh） 5.00-0.3 *35.0+0.5-0.5 *62.0+0.5-0.55.00-0.3 *16.0+0.5-0.5 *21.0+0.5-0.55.00-0.3 *20.0+0.5-0.5 *30.0+0.5-0.55.00-0.3 *20.0+0.5-0.5 *25.0+0.5-0.55.00-0.3 *27.0+0.5-0.5 *30.0+0.5-0.55.00-0.3 *20.0+0.5-0.5 *35.0+0.5-0.51095055601800180045 3.736±11105050681800180045 3.736±1111522022160160180 3.7 3.2±0.511252353355055070 3.711±11135350601800180045 3.736±1114551235170170170 3.7 3.4±111555345095095045 3.719±1116653759150045 3.730±111770242635035090 3.77±111870253252052070 3.710.4±1119701223130130200 3.7 2.6±0.512070255080080050 3.716±0.51217036381000100050 3.720±0.51227315158070330 3.7 1.6±0.5123751126180180180 3.7 3.6±0.512480102580330 3.7 1.6±0.5125801223160160200 3.7 3.2±0.512690186297597545 3.719.5±11273196509090300 3.7 2.3±0.5128552020170170200 3.7 3.4±0.51295551521400140045 3.728±113056223640090 3.78±1131582030300300100 3.76±113258313454070 3.710.8±1133601220100100300 3.72±1134601230170170180 3.7 3.4±0.5135601235200200150 3.74±1136601630240240120 3.7 4.8±1137601735300300120 3.76±1138601045220220130 3.8 4.4±1139602025240240120 3.7 4.8±11406032100A 170045 3.734±11416032100200035 3.738±11426034481000100060 3.720±1143602020170170200 3.7 3.4±114460204045045070 3.79±15.50-0.3 *34.0+0.5-0.5 *50.0+0.5-0.55.00-0.3 *50.0+0.5-0.5 *68.0+0.5-0.57.50-0.3 *12.0+0.0-0.5 *26.5+0.5-0.56.00-0.3 *34.0+0.5-0.5 *48.0+0.5-0.57.60-0.3 *12.0+0.5-0.5 *23.5+0.5-0.57.00.0-0.3 *36.0+0.5-0.5 *38.0+0.5-0.57.00.2-0.3 *12.0+0.5-0.5 *23.0+0.5-0.56.00-0.3 *20.0+0.5-0.5 *40.0+0.5-0.57.00.0-0.3 *25.0+0.5-0.5 *49.0+0.5-0.57.00.2-0.3 *15.0+0.5-0.5 *15.0+0.5-0.5重量（g)7.00-0.3 *24.0+0.5-0.5 *26.0+0.5-0.5电压（V）6.00-0.3 *20.0+0.5-0.5 *20.0+0.5-0.5序号最小容量（mAh） 6.00-0.3 *17.0+0.5-0.5 *35.0+0.5-0.5尺寸(mm)6.00-0.3 *12.0+0.5-0.5 *20.0+0.5-0.56.00-0.3 *32.0+0.5-0.5 *101+0.5-0.56.00-0.3 *32.0+0.5-0.5 *101+0.5-0.55.50-0.3 *51.0+0.5-0.5 *52.0+0.5-0.5型号 5.80-0.3 *20.0+0.5-0.5 *30.0+0.5-0.65.50-0.3 *12.0+0.5-0.5 *35.0+0.5-0.58.00-0.3 *10.0+0.5-0.5 *25+0.5-0.56.50-0.3 *37.0+0.5-0.5 *59.0+1.0-0.57.00-0.3 *25.0+0.5-0.5 *32.0+0.5-0.5内阻（mΩ）标称容量（mAh） 5.00-0.3 *55.0+0.5-0.5 *60.0+0.5-0.5量产规格表5.80-0.3 *31.0+0.5-0.5 *34.0+0.5-0.6厚×宽×高6.00-0.3 *10.0+0.8-0.5 *45.0+0.5-0.65.60-0.3 *22.5+0.5-0.5 *36.5+0.5-0.53.10-0.3 *9.6+0.5-0.5 *47.5+0.5-0.56.00-0.3 *16.0+0.5-0.5 *30.0+0.5-0.55.50-0.3 *20.0+0.5-0.5 *20.0+0.5-0.56.00-0.3 *12.0+0.5-0.5 *30.0+0.5-0.56.00-0.3 *12.0+0.5-0.5 *35.0+0.5-0.56.00-0.3 *20.0+0.5-0.5 *25.0+0.5-0.59.00-0.3 *18.0+0.5-0.5 *62.5+0.5-0.55.20-0.3 *20.0+0.5-0.5 *22.0+0.5-0.55.20-0.3 *35.0+0.5-0.5 *33.0+0.5-0.55.30-0.3 *50.0+0.5-0.5 *60.0+0.5-0.5145602425300300100 3.76±114660253240090 3.78±114760304890090045 3.718±1148653475175045 3.735±11494012154545500 3.7 1.1±0.51502314204040500 3.7 1.1±0.51514011299090270 3.72±0.51526011207575350 3.7 1.8±0.51536534611250125045 3.724.5±0.51543010305050430 3.7 1.4±0.51553510153030670 3.71±0.5156302029130130200 3.7 3.1±0.5157701837420400100 3.78.5±0.51584539661150105045 3.723±0.51594440841600160035 3.730±0.5159803450H 1100110035 4.128±1160481417H 5555170 4.1 1.5±0.2161551417H/601417H 7070160 4.12±0.2162400922H 40163701719H 140 4.1±0.2164701417H 9090140 4.1 2.4±0.2165452030H 15015090 4.1 4.5±0.3166502030H 20020070 4.1 5.3±0.3167501225H 7070150 4.12±0.3168602035H 30030055 4.17.6±0.3169603048H 60060035 4.115.5±0.5170383040H 35035050 4.19±0.5171401220H 4545250 4.1 1.6±0.5172703048H 80080025 4.119.5±0.5173523582H 1250125025 4.131±1174403048H 42042050 4.112±1175453048H 48048045 4.113±1176501723H 100100120 4.1 2.7±0.5177503465H 1000100025 4.126±1.04.50-0.3 *37.5+0.5-0.5 *83.50.5-0.5高倍率电池系列3.10-0.3 *20.0+0.5-0.5 *29.00.5-0.56.30-0.3 *33.5+0.5-0.5 *60.50.5-0.54.10-0.3 *10.5+0.5-0.5 *28.00.5-0.55.90-0.3 *10.5+0.5-0.5 *19.00.5-0.52.40-0.3 *14.0+0.5-0.5 *20.00.5-0.56.50-0.3 *34.0+0.5-0.5 *76+0.5-0.54.20-0.3 *12+0.5-0.5 *15.50.5-0.56.00-0.3 *30.0+0.5-0.5 *48.0+0.5-0.56.00-0.3 *25.0+0.5-0.5 *32+0.5-0.56.00-0.3 *24.0+0.5-0.5 *25.0+0.5-0.5量产规格表厚×宽×高4.50.2-0.3 *30.0+1.0-0.5 *48.0+1.0-0.5尺寸(mm)容量（mAh）8.00.2-0.3 *34.0+1.0-0.5 *50.0+1.0-0.57.00.2-0.3 *14.0+0.5-0.5 *18.0+0.5-0.55.00.2-0.3 *20.0+0.5-0.5 *30.0+0.5-0.56.00.20.3 *30.0+1.0-0.5 *48.0+1.0-0.53.80.20.3 *30.0+1.0-0.5 *40.0+1.0-0.54.00.2-0.3 *12.0+0.5-0.5 *20.0+0.5-0.55.20.2-0.3 *35.0+1.0-0.5 *82.0+1.0-0.54.00.2-0.3 *30.0+1.0-0.5 *48.0+1.0-0.5电压（V）重量（g)7.00.2-0.3 *30.0+1.0-0.5 *48.0+1.0-0.55.00.2-0.3 *17.0+1.0-0.5 *23.5+1.0-0.56.00.2-0.3 *20.0+1.0-0.5 *35.0+1.0-0.5序号型号容量（mAh）内阻（mΩ） 3.50-0.3 *9.5+0.5-0.5 *150.5-0.53.20-0.3 *9.5+0.5-0.5 *29.00.5-0.54.40-0.3 *39.5+0.5-0.5 *83.50.5-0.55.00.2-0.3 *34.0+1.0-0.5 *65+1.0-0.57.00-0.3 *18.0+0.5-0.5 *37.00.5-0.54.80-0.3 *14.0+0.5-0.5 *18.0+0.5-0.55.70.3-0.3 *14.0+0.5-0.5 *18.0+0.5-0.54.50.2-0.3 *12.0+0.5-0.5 *25.0+0.5-0.54.50-0.3 *20.0+0.5-0.5 *30.0+0.5-0.5178502025H 16016090 4.14±0.5版 本制定日期页 次179601719H 100100120 4.1 2.7±0.5180601717H 9090130 4.1 2.4±0.3181653562H 1100110025 4.127±1.0182701224H 100100140 3.7 2.5±0.3183702535H 45045045 3.712.5±0.5184483462H 85085025 3.722±0.5185553462H 95095025 3.723±0.5186703465H 1300130020 3.731±0.5187852040H 50050045 3.715±0.518875400H 15015090 3.74±0.5189581417H 7070145 3.7 2.06±0.319080600H 28028080 3.7 5.7±0.519180500H 21021080 3.7 4.8±0.519280400H 19019080 3.7 3.8±0.519375500H 17017090 3.74±0.519470350H 100100110 3.7 2.5±0.5195651723H 130±0.5196601723H 13013090 3.7 3.3±0.319775400H 120120110 3.7 3.6±0.3198551723H 120120100 3.7 3.0±0.3199903048H 20011500H 36038075 3.78.0±0.32011850020218650P 20318650204505068A 1550155035 3.729±1205535060A 1550155035 3.729±120550344335 3.70±15.30.2-0.3 *50.0+0.5-0.5 *60.0+0.50-0.5审 核制 定刘勇备注：规格表中产品内容仅供参考,详细内容以具体的产品规格书为准!※ 聚合物电芯的尺寸和规格可以按客户的要求定做※ 厚度不同（小于6mm）、长宽相同的电芯，不需另外开模※ 客户要求的电池容量若高于上述的标称容量，则要具体讨论，有颜色部分为新增型号，核 准 5.00.2-0.3 *50.0+0.5-0.5 *68.0+0.50-0.55.30.2-0.3 *50.0+0.5-0.5 *60.0+0.50-0.57.00.2-0.3 *25.0+1.0-0.5 *35+1.0-0.56.00.2-0.3 *17.0+1.0-0.5 *23.5+1.0-0.57.00.2-0.3 *34.0+1.0-0.5 *65.0+1.0-0.55.50.2-0.3 *34.0+1.0-0.5 *62.0+1.0-0.55.00.2-0.3 *34.0+1.0-0.5 *62.0+1.0-0.5深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY TECHNOLOGY CO., LTD.内阻（mΩ） 5.00.2-0.3 *20.0+1.0-0.5 *25.0+1.0-0.56.50.2-0.3 *35.0+1.0-0.5 *62+1.0-0.57.00.2-0.3 *12.0+1.0-0.5 *25+1.0-0.57.80.2-0.3 *50.0+1.0-0.56.00.2-0.3 *17.0+1.0-0.5 *20.0+1.0-0.56.00.2-0.3 *17.0+1.0-0.5 *18+1.0-0.57.80.2-0.3 *60.0+1.0-0.57.30.2-0.3 *40.0+1.0-0.56.80.2-0.3 *35.0+1.0-0.55.50.2-0.3 *17.0+1.0-0.5 *23.0+1.0-0.57.30.2-0.3 *50.0+1.0-0.5其他系列电芯7.80.2-0.3 *40.0+1.0-0.510.30.2-0.3 *50.0+1.0-0.58.30.2-0.3 *20.0+1.0-0.5 *40.0+1.0-0.57.30.2-0.3 *40.0+1.0-0.55.80.2-0.3 *14.0+1.0-0.5 *17.0+1.0-0.5A 2009-12-09PAGE 6 OF 6量产规格表电压（V）重量（g)厚×宽×高序号型号标称容量（mAh）最小容量（mAh）尺寸(mm)。
锂电池规格书参照
聚合物锂离子电池产品规格承认书：：JD220768430F（500Ah）品名：品名编制审核批准客户确认签名//日期客户名称//印章签名客户名称总部：北京神州巨电新能源技术开发有限公司Beijing Globe Super Power New Energy Technology Development Corp.地址：中国北京市海淀区上地3街9号嘉华大厦E座206ADD:Rm E-206,Gem Tech-Center,No.9,3rd Street,Haidian Dist.,Beijing,P.R.China 86-10--82783543-816Fax:86-1086-10--82780720-1073Tel:86-10工厂：河北神州巨电新能源科技开发有限公司Hebei Globe Super Power New Energy Technology Development Corp.地址：河北邢台市巨鹿县巨鹿工业园Hebei i Province,P.R.ChinaADD:Industrial District,Ju Jul l u,Xiangtan,Hebe产品规格承认书目录1.适用范围---------------------------------------------------------------------------------------------------------22.产品规格---------------------------------------------------------------------------------------------------23.电池性能检查测试-----------------------------------------------------------------------------------------24.外观尺寸图------------------------------------------------------------------------------------------------------35.使用指南--------------------------------------------------------------------------------------------------------36.其它事项------------------------------------------------------------------------------------------------------47.电芯处理须知---------------------------------------------------------------------------------------------------41.使用范围本规格书仅适用于巨电新能源制造的聚合物锂电池，型号JD220768430F.2.产品规格序号项目规格备注1充电电压 3.65V2标称电压 3.2V出货状态,电压为3.1V~3.3V.3标称容量500Ah容量是指标准充电后,0.2C放电到2.5V截止电压所放出的容量.平均容量520Ah最低容量500Ah4循环寿命≥2000每圈循环是以250A的电流充放到截止电压为2.5V的间歇过程.当放电容量降至初始容量的80%时,所完成的循环圈数定义为该电芯的循环寿命5自放电剩余容量>90%该容量是指标准充电后,在23°C±2°环境下贮存30天,以No.3的条件下所测得的容量.6内阻≤2mohm标准充电后,在AC1KHz条件下测量的交流阻抗. 7最大充电电流1C(500A)8最大放电电流1C(500A)9放电截止电压 2.5V10工作温度放电状态:-20°C~+60°C充电状态:0°C~+45°C贮存状态:-20°C~+45°C贮存电压为3.1V~3.3V.若需长时间存放,每隔90天需将电芯充放电一次.11温度特性60ºC@0.2C:98%23ºC@0.2C:100%-20ºC@0.2C:75%电池标准充电后,在测试温度下搁置4小时，然后在测试温度条件下以0.2C恒流放电至2.0V时所放出来的容量与在标准温度23°C±2°C)放电容量之比12净重约15kg13外型尺寸长：470.0mm Max宽：785.0mm Max厚：23.0mm Max不包括极耳3.电池性能检查测试3.1外观检查电芯表观应完整,不允许有刮痕,褶皱,裂纹,漏液等会导致电芯性能损坏的缺陷.3.2标准测试环境除非特别说明，本产品规格书中的所有测试均在以下环境条件下进行：温度：23°C±2°C湿度：65±20%3.3充放电方法和条件序号项目测试方法及条件1充电电流标准充电电流：0.2C(100A)快速充电电流：1C(500A)2标准充电先用0.2C(100A)恒流充电至3.65V,再用3.65V恒压(精度3.65±0.05V)充电至电流0.02C(10.0A)。
锂电池规格参数表
部分规格产品技术指标
序 系列
号
型号
标称容量 (mAh)
1 1030 PL321030 60
2 1116 PL651116 70
3 1230 PL051230 130
4
PL041235 120
1235
5
PL051235 140
6 1245 PL061245 240
7
PL381429 100
1429
8
PL041429 120
单体电池技术指标 4 方型锂离子电池 （钢壳、铝壳锂离子电池）
该电池充放电性能卓越，自放电小，无记忆效应；安全性能好；可在－ 20 ℃ ～ 60 ℃ 的环境下工作。其重 量、容量、充放电性能均优于其它类型电池。主要应用于手机。
部分规格产品技术指标
序
标称容量 内阻 标称电压
号 系列 型 号 (mAh) (mΩ) (V) 厚度(±0.2)
厚度 (±0.2) 3.2 6.5 5 4 5 6 3.8 4 4 5 5 6 3.8 5 8 3.8 3.5 3.8 4 5 5.2 5.8 4 5 6 6.3 5 5 4 5 5.8 5.2 4.2 6 6 5 4 7.2
尺寸(mm) 宽度(±0.5)
10.5 11.5 12.5 12.5 12.5 12.5 14.5 14.5 14.5 14.5 16.5 17.5 17.5 17.5 19.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 21.5 22.5 27.5 30.5 30.5 30.5 30.5 30.5
国际领先水平。
循环性能：在室温下 1C 充放电循环 1500 次，容量保持率 95 ％上；
锂离子电池产品规格书说明书
History of specification规格书修订记录Date Contents Remarks 2018-05-12First issue A0Content/目录1.Scope/适用范围Page42.Cell Specification/电芯规格说明Page4/53.Battery/Cell performance test Criteria/电池性能标准Page6 3.1Appearance inspection by visual/外观目测Page6 3.2Environmental test condition/外界环境条件Page6 3.3Electrical characteristics/电气特性Page6 3.4Mechanical characteristics/机械特性Page73.5Safety performance/安全性能Page7/84.Cell initial Dimensions/电芯初始尺寸Page84.2Picture of assembled battery组合电池图5.Protection Circuit保护电路5.1PCM parameter PCM参数6.Circuit topology Drawing and PIN Explanation电路布线图和焊盘说明6.1PCM BOM保护板物料清单6.2Assembled cell parameters包装后电芯组参数附录Page9 Page9 Page9 Page10 Page10 Page101.Scope/适用范围2.Cell Specification/电芯产品规格No.Item项目Specification性能1Rated Capacity额定容量3000mAh,0.2C discharging2Minimum Capacity最小容量3000mAh,0.2C discharging3Normal Voltage标称电压3.70V4O.C.V出厂电压 3.80-4.2V5Charge Ending Voltage充电截止电压4.20±0.03V6Discharge Ending Voltage放电截止电压3.0V7Standard charging method标准充电方式0.5C constant current charge to 4.2V,then constantvoltage4.2V charge till charged current declines to≤0.01C,0℃～45℃8Charge current充电电流Standard charge:0.5CRapid charge:1.0C9charging Time充电时间Standard charge:5.5～6.5hRapid charge:1.5～2.5h10Max.Charging Current最大充电电流1.0C(5℃～+45℃)11Standard dischargingCurrent标准放电电流0.5C constant current discharge to3.0V.10℃～+60℃12Max.Discharging Current最大放电电流1.0C(10℃～+60℃)13Operating environment工作环境Charging:0℃-45℃,65%±25%RHDischarging:10℃-60℃,65%±25%RH14Cell Impedance单电芯内阻＜45mohm，(4.2V AC1KHz measured)15Dimension of Single Cell单电芯尺寸Thickness Max8.0mmWidth Max56.5mmHeight Max60.5mm3.Picture of single cell单体电芯图Items Description Dimension and SpecT电芯厚度Max:8.0mmW电芯宽度Max:56.5mmH电芯长度Max:60.5mmC Tab间距18±2.0mmB Tab宽度 4.0±0.1mmD顶封宽度 4.0±0.5mmA极耳胶外露Max:2.0mmE极耳长度8.0±1.5mmFig.(1)The Dimension of Single Cell图(1)单体电池尺寸图4.Picture of assembled battery组合电池图Fig.(2)The Dimension of Assembled Battery图(2)组合电池外形尺寸图厚度T 宽度W 长度L 线径Ø线型插头型号Max:8.1Max:57.0Max:63.00.9UL1007/24#XH2.54-2P备注：UNIT 单位：MM5.产品规格及电气参数Product Specification and Electrical Parameters序号Item项目Specification性能1Assembled Mode组合方式1P2Normal Capacity标称容量≥3000mAh,0.2C discharging3Normal Voltage标称电压3.7V4Impedance成品内阻＜103mohm，(100%charge AC1KHz measured)5Assembly Dimension装配尺寸Thickness Max8.1mmWidth Max57.0mmHeight Max63.0mm4.Battery/Cell performance test Criteria/电池性能标准4.1Appearance inspection by visual/外观目测There shall be no such defect as rust,leakage,which may adversely affect commercial value of battery.电池外观应没有锈渍、污渍、漏液等影响商业价值的缺陷存在。
电池规格书模板
Specification Approval Sheet 产品规格承认书Customer 客户名称：域拓Model产品型号：4LType 产品类型：Li-ion battery Specification产品规格：3.7V/1400mAHAMENDMENT RECORDSCatalogue 目录1 .Battery type and scope电池型号和适用范围 (3)1 . 1: model产品型号： (4)1 . 2: scope适用范围：客户定义 (4)2 . Basic character and compose of battery电池的基本特性及组成 (4)2 . 1: fundamental performance parameter of battery电池基本性能参数： (4)2 . 2: Main components and parts主要零部件 (6)2 . 3: Regular performance and unfailing performance产品常规性能和可靠性能 (6)2 . 4: Contour Dimension of the Battery电池外形尺寸 (11)3 . Specifications of Parts零部件规格 (102)3 . 1: fender保护板 (102)3 . 2: general electric and protection characters一般电气与保护特征 (102)3 . 2: electric schematic diagram of battery电池电路原理图： (113)3 . 3 : PCB layout 电路布局图………………………………………………………………….错误!未定义书签。
34 . Specifications of the Cells电芯规格 (124)Announcements注意事项 (135)Danger 危险 (135)Warnings 警告 (146)Announcements 注意事项 (157)1 .Battery type and scope电池型号和适用范围This Specification Approval Sheet is for rechargeable Li-polymer battery provided by Shirui Battery Co., LTD.This product is according with the national standard of PRC. ‘GB/T18287-2000’. ‘General specification of lithium-ion battery for cellular phone’.本《规格书》为时瑞电池有限公司提供的可充电式锂离子电池规格。
聚合物锂离子电池组件规格书
范围1.
本文件描述了深圳市弘毅电池有限公司研制的聚合物锂离子电池的产品规格、测试方法。产品类别和产品型号2.
类别2.1
聚合物锂离子蓄电池
产品型号2.2
PL-052030
产品基本特性3.
备注项目特性序号AC时，0.2A充电2.5小1最小240mAhC553.1容量。恒流放电到典型250mAh 3.0V 3.2 3.7V工作电压3.3 4.20V最大充电终止电压3.0V
深圳电池有限公司SHENZHEN BATTERY CO., LTD.
编号:SPE-P001版本:00 :2005-9-7日期
聚合物锂离子电池组件
产品规格书
型号: PL-052030
编制/日期审核/日期批准/日期
深圳电池有限公司
SHENZHEN BATTERY CO., LTD.
:SPE-P001编号:00版本:2005-9-7日期
6AGE 3 OF P
深圳电池有限公司SHENZHEN BATTERY CO., LTD.
:SPE-P001编号:00版本:2005-9-7日期
产品规格书PL-052030
求目要项单序号元
0.049V 4.200±充电器充电终止电压1
0.025V 4.275±2过充保护电压0.050V±4.1753过充恢复电压
安全特性6.2
项目序号标准测试方法
3
以电流电流恒流放电至3.0V，电池以1CA51不爆炸、不起火过充实验小时。4.8V的制式充电8C限制电压5电流恒流放电至A3C电池完全充电后，以52不爆炸、不起火过放实验结束。-10V或超过2.5h的不锈钢钉在完全5.0mm将1根直径为2.0～3
不爆炸、不起火针刺实验充电的电池表面通过外力作用穿透而过。将充满电的电池放在重力对流或循环空气的4不爆炸、不起火热冲击实验烘箱中进行加热，烘箱的温度以5±2℃的速
聚合物锂电池401520规格书
egrahC dradnatS smetI
电充准标
1 .O N
能性电放充 scitsiretcarahc lacirtcelE 1.4
airetirC ecnamrofreP lleC yrettaB.4
试测及查检能性芯电
41 fo 4 :EGAP A : .VER 810 :.ON COD
司公限有技科子电达立迅海珠
寸尺芯电 noisnemiD lleC 量重芯电 thgieW lleC 度温存储 erutarepmet egarotS 度温作工 erutarepmet gnitarepO 压电止截电放 egatlov ffo-tuc egrahcsiD 流电电放大最 tnerruc egrahcsid.xaM 流电电充大最 tnerruc egrahc.xaM 间时电充 emit gnigrahC 法方电充准标 dohtem gnigrahC dradnatS 流电电充 tnerruc egrahC 量容称标 yticapac lanimoN 压电称标 egatlov lanimoN smetI 压电电充 egatlov egrahC
认确户客
准批
核审
定制
025154 SCI
025154 SCI �号
:ledoM
型
�芯电�书认确格规品产 )lleC(teehS lavorppA noitacificepS
41 fo 1 :EGAP A : .VER :.ON COD 810
司公限有技科子电达立迅海珠
31 21 11 01 01 9 8 7 7 6 5 4 3 3 3
定确商协方双经须�项事的及提未中书明说本何任 .NUJOUHZ dna remotsuc eht neewteb derrefnoc eb dluohs revoc ton seod noitacificeps siht taht srettam ynA 项事它其 srehtO )b
2400mAh聚合物锂离子电池规格书
产品规格书（Product Specification）型号（Model No.）GLP873496 2400mAh 25C 11.1V产品规格书（Product Specification）型号（Model No.）GLP873496 2400mAh 25C 11.1VCon tent目录1. 序言3Preface2. 型号：GLP873496 3Model: GLP8734963. 产品规格3Specification4. 电芯性能检查及测试4Battery Cell Performance Criteria5. 贮存及其它事项5Storage and Others6. 聚合物锂离子充电电芯操作指示及注意事项5- 8 Handling Precautions and Guideline6.1. 充电5- 6Charging6.2. 放电6- 7Discharging6.3. 贮存7Storage6.4. 电芯操作注意事项7Handling of Cells6.5. 电池外壳设计注意事项7Notice for Designing Battery Pack6.6. 电池与外壳组装注意事项7-8Notice for Assembling Battery Pack7. 其它事项8-9Others8.组装图9Packing plan型号（Model No.）GLP873496 2400mAh 25C 11.1V 产品规格书（Product Specification ）1. 序言 PREFACE此规格书适用于池能电子科技有限公司的锂聚合物可充电电池产品The s p e c i f i c a t i o n i s s u i t a b l e f o r t h e p e r f o r m a n c e o f Lithium-Polymer (LIP) r e c h a r g e a b l e b a tt e r y p r o d u c e d by t h e Dongguan Chineng Electronic Technology Co., Ltd .2. 型号 MODELGLP873496 2400 25C 11.1V3.产品规格 SPEC IFICAT ION单颗电池规格 S p e c i f i c a t i o n s o f s i n g l e c e ll4. 电芯性能检查及测试 BATTERY CELL PERFORMANCE CRITERIA在进行下例各项测试前每颗电池应用 0.5C 放至 3.0V 。
600ma聚合物锂电池最大放电电流
600ma聚合物锂电池最大放电电流600ma聚合物锂电池最大放电电流，是指该类型电池在正常使用时，可以提供的最大放电电流。
下面将从电池特点、使用注意事项和相关应用方面对该电池的最大放电电流进行详细介绍。
首先，600ma聚合物锂电池具有以下特点：1.高能量密度：聚合物锂电池相对于传统的液态锂电池具有更高的能量密度，可以提供更长的工作时间。
2.轻巧便携：因为聚合物锂电池使用了聚合物作为电解质，相比于传统液态锂电池，更轻薄，更适合于移动设备。
3.安全性高：聚合物锂电池具有较低的燃烧风险，该电池在高温、过充/过放和物理损坏等情况下的安全性更高。
在使用600ma聚合物锂电池时，需要注意以下几点：1.避免过度放电：尽量避免将电池放电至过低的电量，可以延长电池的寿命和使用时间。
2.避免过度充电：同样，避免将电池充电至过高的电量，过度充电会导致电池损坏甚至发生安全事故。
3.温度控制：尽量避免电池在极端高温或低温下使用，这样可以保持电池的正常工作状态。
600ma聚合物锂电池的最大放电电流在一些应用方面非常有指导意义，下面列举几种常见的应用场景：1.智能手表：智能手表通常对电池寿命和轻巧度有较高要求，600ma聚合物锂电池的最大放电电流能满足日常使用需求。
2.蓝牙耳机：蓝牙耳机体积小，使用600ma聚合物锂电池可以为其提供稳定的电力支持。
3.便携式充电器：便携式充电器通常需要较高的输出电流，在不过载的情况下，600ma聚合物锂电池是一个合适的选择。
4.智能家居设备：智能家居设备通常需要长时间的连续供电，而600ma聚合物锂电池的高能量密度可以满足这一需求。
最后，600ma聚合物锂电池的最大放电电流不仅在设计和生产过程中有重要意义，也对用户在日常使用中起到了指导作用。
用户在购买和使用时应注意电池的安全性和合适的使用环境，以保证其长时间、稳定的工作。
聚合物锂离子电池商品说明书
Item
Test Methods
Performance
At 20±5℃, charging batteries with constant current
7.1 Over charge 3C5A to voltage5V, then with constant voltage5V till current No explosion or fire decline to 0. Stop test till batteries’ temperature 10℃ lower
It is claimed that we should have no any responsibility with the contingency and loss due to the cells’ wrong usage (not preferred in the product specification).
8. Cautions
8.1 Cautions of batteries’ operation The batteries must be careful of proceed the operation for its soft package.
8.1.1 Aluminum packing materials The aluminum packing material was easily damaged by the sharp edge part, such as nickel-tabs. ⑴ forbid to use the sharp part touching the battery;
keeping time 16ms; all collision times 1000±10.
Polymer Lithium-Ion 600mAh 3.7V 电池说明书
304050304050Specification Approval Sheet Name：Polymer Lithium-Ion BatteryModel： CELLEVIA BATTERIES LPSPEC：3.7V/ 600mAhNumber:Specification Modification Records1.Scope:This specification describes the Product Specification of chargeable Polymer Lithium-IonBattery produced by Cellevia.Any copies are invalid without our company’s approval2.Model :3.Cell parameters Index:3.2 Parameters of batterythe temperature.4.Electronic Characteristics test and inspection:4.1 Standard testing environmentUnless special stated, tests should be done within one month of delivery and thecharging-recharging times is less than 5 times. The following is test conditions: Ambient Temperature： 25℃±0.5℃Ambient Humidity： 65 ±20%4.2 The requirement of measure instrument(1) The measure instrument is passed tested by qualified institute.(2) The accuracy of the size instrument is not more than 0.01mm.(3) The accuracy of multimeter is not less than 0.5%. while measure the voltage, theinternal resistance mustn’t less than 10KΩ.(4) The principal of the internal resistance is 1KHz LCR, the accuracy is 0.2%.(5) The internal resistance is changeable, it varies according to the temperature and thecharging mode. And it is relevant to the PTC and the length and the Capacity of the drawing line.(6) The current accuracy of the battery test system is more than ±0.1%,is obaricallyaccuracy is ±0.5%, timer accuracy is less than ±0.1%.(7) The accuracy of the temperature meter is less than ±0.5℃.4.3 Visual inspectionAny visual inspection defects will affect the electronic characteristics, such as cracks,leakage, and flaw, are not in existence.Notes： The Max. voltage while charging is not more than 4.25V.The Max.protective voltage designed on PCB board should not more than4.3V.5.1 Long Period StorageIf the cell has been stored for 3 month, it should be transfer to a dry and cool environment. Storage Voltage is between 3.6V and 3.9V and the storage conditions as Item 4.1.5.2Any matters that this specification does not cover should be conferred between thecustomer and CELLEVIA304050Specification Approval sheet6.Drawing6.1 Assembly diagram(not in scale)Model ：LP30adhesive wire black AWG2660wire red (+)AWG265070connector! Danger●Strictly prohibits heat or throw cell into fire.●Strictly prohibits throw and wet cell in liquid such as water, gasoline or drink etc.●Strictly prohibits use leave cell close to fire or inside of a car where temperature may be above60°C. Also do not charge / discharge in such conditions.●Strictly prohibits put batteries in your pockets or a bag together with metal objects such asnecklaces. Hairpins,coins, or screws. Do not store or transportation batteries with such objects.●Strictly prohibits short circuit the (+) and (-) terminals with other metals.●Do not place Cell in a device with the (+) and (-) in the wrong way around.●Strictly prohibits pierce Cell with a sharp object such as a needle.●Strictly prohibits disassemble or modify the cell.●Strictly prohibits welding a cell directly.●Do not use a Cell with serious scar or deformation.●Thoroughly read the user’s manual before use, inaccurate handling of lithium ion rechargeablecell may cause leakage, heat, smoke, an explosion, or fire, capacity decreasing.! Warning●Strictly prohibits put cell into a microwave oven, dryer, or high-pressure container.●Strictly prohibits use cell with dry cells and other primary batteries, or new and old battery orbatteries of a different package, type, or brand.●Stop charging the Cell if charging is not completed within the specified time.●Stop using the Cell if abnormal heat, odor, discoloration, deformation or abnormal condition isdetected during use, charge, or storage.●Keep away from fire immediately when leakage or foul odor is detected.●If liquid leaks onto your skin or clothes, wash well with fresh water immediately.●If liquid leaking from the Cell gets into your eyes, do not rub your eyes. Wash them well with cleanedible oil and go to see a doctor immediately.! Caution●Before using the Cell, be sure to read the user’s manual and cautions on handling thoroughly.●Charging with specific charger according to product specification. Charge with CC/CV method.Strictly prohibits revered charging. Connect cell reverse will not charge the cel. At the sametime, it will reduce the charge-discharge characteristics and safety characteristics, this will leadto product heat and leakage.●Store batteries out of reach of children so that they are not accidentally swallowed.●If younger children use the Cell, their guardians should explain the proper handling.●Before using the Cell, be sure to read the user’s manual and cautions on handling thoroughly.●Batteries have life cycles. If the time that the Cell powers equipment becomes much shorter thanusual, the Cell life is at an end. Replace the Cell with a new same one.●When not using Cell for an extended period, remove it from the equipment and store in aplace with low humidity and low temperature.●While the Cell pack is charged, used and stored, keep it away from objects or materials with staticelectric charges.●If the terminals of the Cell become dirty, wipe with a dry clothe before using the Cell.●Storage the cells in storage temperature range as the specifications, After full discharged, wesuggest that charging to 3.9~4.0V with no using for a long time.●Do not exceed these ranges of the following temperature ranges.Charge temperature range : 0 °C to 45 °C;Discharge temperature range : -20 °C to 60 °C.(When using equipment)Handling Precaution and GuidelineFor LIP (Lithium-Ion Polymer) Rechargeable BatteriesPrefaceThis document of ‘Handling Precautions and Guideline LIP Rechargeable Batteries’shall be applied to the battery cells manufactured by CELLEVIA.Note (1): The customer is requested to contact CELLEVIA in advance, if and when the customer needs other applications of operating conditions than those described in this document. Additional experimentation may be required to verify performance and safety under such condition.Note (2): CELLEVIA will take no responsibility for any accident when the cell is used under other condition.Note (3): CELLEVIA will inform, in a written form, the customer of improvement(s) regarding proper use and handling of the cell, if it is deemed necessary.1. Charging 1.1ChargingCurrent:Charging current should be less than maximum charge current specified in theSpecification Approval Sheet.1.2 Charging Voltage:Charging voltage should be less than the maximum nominal voltage 4.2V, andthe charging voltage upper limited is 4.30V(single pack).1.3 Charging Temperature:The cell should be charged within the range specified in this Specification ApprovalSheet.1.4 Notes:Since charging with constant current or constant voltage, reverse charging isprohibited. In case of the cell is connected improperly, the cell cannot be charged.Simultaneously, the reverse charging may cause damaging to the cell whichmay lead to degradation of cell performance and damage the cell safety, andcould cause heat generation or leakage.2. Discharging Current:The cell shall be discharged at less than the maximum discharge current specified in the Specification Approval Sheet. High discharging current may reduce the discharging capacity significantly or cause over-heat.3. Discharging TemperatureDischarging Temperature should be within the range specified in this Specification Approval Sheet.4.Over-DischargeOver-discharging will cause cell low-performance and function loss. The cell would be in a over-discharged state by its self-discharge characteristic. In order to prevent over-discharging, the cell shall be charged periodically to maintain between 3.6V and 3.9V. 5. Protective Circuit Module5.1 The cell / battery pack shall be with a PCM that can protect cell / battery packproperly. PCM shall have functions of(1) Overcharging prevention(2) Over-discharging prevention(3) Over current prevention to maintain safety and prevent significant deterioration5.2 Overcharging ProtectionOvercharging prevention function shall stop charging if any cell of the battery packreaches 4.30V.5.3 Over-discharging protectionOver-discharging protection function shall monitor the voltage of every cell in the pack, and work to avoid further drop in the cell voltage of 2.9V or less.6. StorageCells should be stored in proper temperature specified in Specification ApprovalSheet.7. AppearanceIt shall be free from any defects such as remarkable scratches, breaks, cracks,discoloration, leakage or deformation .8. Notice△!8.1 Handling of cells:Avoid any short-circuit, it will caused the pole hot and lost electronic functions.Soft packing is very damaged by sharp edge parts such as needles and knives.Avoid cells touch with sharp edge part, when handling and storage.Beside the poles is the sealed edge. Don’t bend or fold dealing edge, for it is a sensitive part.Don’t open the folding edge on both sides of the cells.Don’t bend the tabs, for the tabs are not so stubborn.Avoid mechanical shock to the cells.Don’t put the cells into the heater, washing machine or high-voltage container.Don’t use the charger without any safety guarantee, and recommend you use specified charger.You should immediately stop charging, as cell is overheating, delivery any smell, changed color, distortion etc.Before Children use batteries, adults should explain the usage first.Before use batteries, please read the handling guideline carefully and fully understand.Away from the static-electronic field, while using, charging and storing cells.Don’t put the cells together with metal conductors such as chains, barrette, bolt into the pocket or stored them together.Don’t use metal conductor to shortcut the positive and negative poles.Don’t mis-assemble the positive pole with the negative one.8.2 Notice for Designing Battery Pack8.2.1 Package DesignBattery pack should have sufficient strength and battery should be protected from mechanical shock.No sharp edge components should be inside the pack containing the battery.8.2.2 PCM DesignThe overcharge threshold voltage should not be exceed 4.30V (single pack)The over-discharge threshold voltage should not be lower than 2.9V (single pack)8.3 Notice for Assembling Battery Pack8.3.2 Tab connectionUltrasonic welding or spot welding is recommended to connect battery with PCM or other parts.If apply manual solder method to connect tab with PCM, below notice is very important to ensure battery performance.8.3.2.1 The solder iron should be temperature controlled and ESDsafe.8.3.2.2 Soldering temperature should not exceed 350℃.8.3.2.3 Soldering time should not be longer than 3 seconds .8.3.2.4 Keep battery tab cold down before next time soldering.8.3.2.5 Directly heat cell body is strictly prohibited. Battery shouldbe damaged by heat above approx. 60℃.8.3.3 Cell fixingThe battery should be fixed to the battery pack by its large surface area.No sharp edge at the assembling position.No cell movement in the battery pack should be allowed.9.Others9.1 The disassembling may generate internal shout circuit in the cell, which may causegassing, firing, or other problem.9.2 Prohibition of dumping of cells into fireNever incinerate or dispose the cells in fire, for these may cause firing of the cells.9.3 The cells should never be soaked with liquids such as water, drinks or oil.9.4 Prohibit using the cells mixed with different manufactories. Prohibit using new cellsmixed with old ones.▲Special Notice: If the cell isn’t used for a long time, Please Keep the cells in half-charged state, which is keeping them unfully charged or incompletely discharged. Recharge the cells and use half of the power after 2-3months. Store the cells in cool and dry place. It will protect the cell from damage effectively and long-term.10. StatementIf our specifications material, product process or product control system has changed, the information will be transmitted to consumer by way of written with quality and reliability data.。
4000mAh 7.4V 8.4V聚合物锂电池规格书与使用注意事项
1、适用范围本规格书描述电池之标称参数，电气特性，安全性能，环境适用性及其实验和判定，使用说明和安全规程，质量评定及包装，标志，贮存，运输等。
适用于采用单体锂电芯制成的电池。
2、引用标准GB/T18287-2000 中华人民共和国蜂窝电话用锂离子电池总规范；3、电芯说明4、电气特性189g±1g4.5环境温度4.5.1充电温度:0～45℃4.5.2放电温度:-20～50℃4.5.3存储:3个月内存储在温度:-20℃～45℃,相对湿度：45%～75%，大气压力：70～106Kpa；3个月上存储在温度:5℃～35℃,相对湿度：45%～75%，大气压力：70～106Kpa。
4.6保用期限1年5、标准条件下的电气特性及其试验方法和判定规则5.1标准测试条件温度 20℃±5%相对湿度 60±15%大气压力86～106Kpa5.2测试仪表要求电压表要求：测量电压的仪表准确度不低于0.5级内阻不小于10KΩ/V。
电流表要求：测量电流的仪表准确度不低于0.5级。
温度计要求：测量温度的仪表准确度不低于±0.5℃。
恒流源的电流恒定可调，其电流变化应在±1%范围内。
恒压源的电压可调，其电压变化应在±0.5%范围内。
A放电容量5.4.1 0.2C5试验方法：电池按规定充电方式标准充电后，搁置一段时间（0.5h～1.0h），在20℃±5℃以0.2CA电流放电至终止电压6.0V5判定标准；上述试验可以重复循环5次，当循环过程中有一次电池放电时间不小于300分钟，试验时取该次放电容量。
5.4.2 2000mA放电容量试验方法：电池按规定充电方式快速充电后，搁置一段时间（0.5h～1.0h），在20℃±5℃的以 2000mA电流放电至终止电压6.0V判定标准；电池放电时间不小于110分钟。
5.4.3温度适应性5.4.3.1高温放电性能试验方法：在环境温度为20℃±5℃的条件下,电池标准充电后,将电池放入55℃±2℃的高温箱中恒温2小时,然后以2000A电流放电至6.0V，将电池取出放在20℃±5℃的环境下搁置2小时后检查外观。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
A
First Edition
Page 2 o f 1 6
VER: A
深 圳 市 言 九 电 子 科 技 有 限 公 司 YJ POWER GROUP LIMITED
1
DATE:15.10.10
Scope（适用范围） This specification is applied to the reference battery in this Specification and manufactured by
VER: A
深 圳 市 言 九 电 子 科 技 有 限 公 司 YJ POWER GROUP LIMITED
Customer/客户: DATE:15.10.10
Li-ion Polymer Battery Specification
锂离子聚合物电池规格书
MODEL/型号: YJ-PL802040（600mAh）
7
Standard discharge （标准放电）
8
Fast charge (快速充电)
Charge time : Approx 2.5h （充电时间：大约 2.5 个小时）
Page 3 o f 1 6
VER: A
深 圳 市 言 九 电 子 科 技 有 限 公 司 YJ POWER GROUP LIMITED
3.1 Standard Test Conditions（标准测试条件） Test should be conducted with new batteries within one week after shipment from our factory and the cells shall not be cycled more than five times before the test. Unless otherwise specified, test and measurement shall be done under temperature of 20 ± 5 ℃ and relative humidity of 45~85%. If it is judged that the test results are not affected by such conditions, the tests may be conducted at temperature 15~30℃ and humidity 25~85%RH. 测试必须使用出厂时间不超过一个星期的新电池， 且未进行过五次以上的充放电循环。 除非特别说明， 否则测试会在温度 20±5℃，相对湿度 45~85%的条件下进行。如果经鉴定测试结果不受上述条件影响， 测试也可以在温度 15~30℃，相对湿度 25~85%RH 的条件下进行。 3.2 Measuring Instrument or Apparatus（测量器具及设备） 3.2.1 Dimension Measuring Instrument（尺寸测量器具） The dimension measurement shall be implemented by instruments with equal or more precision scale of 0.01mm. 尺寸测量器具的精度等级应不小于 0.01 mm 。 3.2.2 Voltmeter（伏特计） Standard class specified in the national standard or more sensitive class having inner impedance more than 10kΩ/V 按照国家标准指定规格等级或采用灵敏度更高的，测量电压时内阻不应小于 10kΩ/V。 3.2.3 Ammeter（安培计） Standard class specified in the national standard or more sensitive class. Total external resistance including ammeter and wire is less than 0.01Ω. 按照国家标准指定规格等级或采用灵敏度更高的，包括电流表及电线在内的总外阻应小于 0.01Ω。 3.2.4 Impedance Meter（电阻计） Impedance shall be measured by a sinusoidal alternating current method(1kHz LCR meter). 内阻测试仪测量原理应为交流阻抗法（1kHz LCR） 。 3.3 Standard Charge\Discharge（标准充放电） 3.3.1 Standard Charge ：Test procedure and its criteria are referred as follows: 标准充电：测试过程及标准如下： 0.5C5A =300mA Charging shall consist of charging at a 0.5C5A constant current rate until the cell reaches 4.2V. The cell shall then be charged at constant voltage of 4.2 volts while tapering the charge current. Charging shall be terminated when the charging current has tapered to 0.01 C5A . Charge time : Approx 4.0h, The cell shall demonstrate no permanent degradation when charged between 0 ºC and 45 ºC. 电池先 0.5C5A 恒流充至 4.2V，当充电电流逐渐减小时再以 4.2V 恒压充至电流减小到 0.01 C5A， 充电时间大约为 4 个小时。在 0℃-45℃内充电电池应没有永久损害。 3.3.2 Standard Discharge（标准放电） 0.2C5A =120mA Cells shall be discharged at a constant current of 0.2 C5A to 2.75 volts @ 20º 5C 电池以 0.2 C5A 恒流放电至 2.75V @ 20º 5C 3.3.3 If no otherwise specified, the rest time between Chare and Discharge amount to 30min. 如果没有特别说明，电池充放电间隔时间为 30 分。
2
3
2.75V
4
4.2±0.03V Internal resistance measured at AC 1KHZ after 50% charge （半电态下用交流法测量内阻） The measure must uses the new batteries that within one week after shipment and cycles less than 5 times (使用出货后不到一个星期及循 环次数少于 5 次的新电池测量) Charge time : Approx 4.0h （充电时间：大约 4 个小时）
Prepared By/Date 编 制/日 期 Checked By/Date 审 核/日 期 Approved By/Date 批 准/日 期
MNX/2015.10.10
FCY/2015.10.10
LP/2015.10.10
Signature/Date(签名/日期)
Company Name(公司名称)
Customer Approval
Company Stamp(公司印章)
Page 1 o f 1 6
VER: A
深 圳 市 言 九 电 子 科 技 有 限 公 司 YJ POWER GROUP LIMITED
DATE:15.10.10
Amendment Records （修正记录）
Edition (版 本) Description （记 述） Prepared by （编 制） Approved by （批 准） Date （日 期）
60±25%R.H. Bare Cell （单体电池储存湿度范围）
Less than 1 year: -20~25℃ （小于一年：-20~25℃） 13 Storage Temperature Range （储存温度范围） less than 3 months: -20~40℃ （小于 3 个月：-20~40℃） Height: Max 41.5 mm (高度：最大 41.5mm) Pack Dimension （包装后尺寸） Width: Max20.5mm (宽度：最大 20.5mm) Thickness: Max8.2mm (厚度：最大 8.2mm)
60±25%R.H. at the shipment state （出货状态时的湿度范围）
14
Initial Dimension （初始尺寸）
Page 4 o f 1 6
VER: A
深 圳 市 言 九 电 子 科 技 有 限 公 司 YJ POWER GROUP LIMITED
3 Performance And Test Conditions (电池性能及测试条件)
DATE:15.10.10
9
Fast discharge (快速放电)
10
Maximum Continuous Charge Current (最大充电持续电流)
1 C5A
11
Maximum Continuous Discharge Current （最大放电持续电流）
1.5C5A
Charge（充电）: 0~45℃ 12 Operation Temperature Range （工作温度范围） Discharge（放电）: -20~60℃