奔克bp300控制系统及系统菜单

德国奔克bp300控制系统技术手册以及系统菜单

Böhnke + Partner GmbH Werkskonfiguration BP公司出厂菜单设置———————————————————————————————————Steuerungsnr.控制器号: 87576

Kunde客户: ZHAO

Aufzugsnummer电梯号:

Sonderangaben特殊说明: ———————————————————————————————————

StrgNr.控制器号: 87576

AufzNr.电梯号:

ProVer.程序版本: 35X-9.04b 14:00

CDA-03

CLP-03

IO-CoP. 输入输出协处理器: V2.9

DCPCoP. DCP协处理器: V5.7 ———————————————————————————————————

base menu 基本菜单

lift data 电梯数据:

highest landing 最高层站: 5

lowest landing 最低层站: 1

SST at floor : no entry 未用

type of lift 电梯类型: rope with speed regul. frequency VVVF曳引梯

frequency reg. Type变频器类型: F20: ZETADYN 2CF Ziehl Abegg

type of system 系统类型: single lift 单梯

shaft copying 井道信息: without switches (encoder at SP7) 无磁开关,编码器接于SP7 type of control 控制类型: full collective select call cancel 全集选,行驶方向召唤消除

楼层显示: gray code 格雷码

All-level offset 所有层站偏移量: 0

via A14/A15 经A14/A15 : 7-segmentcode 7段码

: 2345

start.sp. l fl 启动速度: ssss

: 1234

functions rope 曳引梯功能:

safety switching 安全开关: : stop at level with blocking 平层停车,电梯禁用

re-levelling 再平层: with levelcontact 用平层接触开关

relevel-switch 再平层开关: make contact 常通

relevelling control 再平层控制: cancel releveling at landing 在门区时取消再平层

re-levelling 再平层: via main device 经主设备

re-levelling 再平层: with c1.153 用接线端153

levell.door close 关门时再平层: normal 正常

re-levelling 再平层: stop before normal start 在正常启动前停止

re-levelling 再平层: brake not delayed 制动不延时

PTC thermistor 温控电阻: immediate stop with blocking 立即停车,电梯禁用control term.9 监控线端9 : with blocking 电梯禁用

故障线端35 : immediate stop with blocking立即停车,电梯禁用

regulation contr. 调速器监控: immediate stop with blocking立即停车,电梯禁用travel direct. sig. 运行方向指示: when going down 正到达时

brake open after 制动开,当: signal c1.31=1 信号接线端31=1

brake close after 制动关,当: signal c1.31=0 信号接线端31=0

re-levelling 再平层: brake not delayed 制动不延时

signal c1.21 信号接线端21 : help-sig. brake 制动器辅助信号

signal c1.31 信号接线端31 : make contact 常通

signal c1.34 信号接线端34 : break contact 常断

speed reduction 减速: from Vs to Vz 从Vs到Vz

standard funct.标准功能:

inspection 检修: pushb.fast+door open/close=off 快速键+开关门键=关闭inspection 检修: up to level 直至平层

inspection 检修: without close door signal 无关门信号

inspection 检修: without lock-sig. c1.48 接线端48无门锁信号

insp./ : according EN81 按照EN81标准

start off zone 门区外启动: distant-triP 远程运行

correction signals 校正信号: break contact 常通

correction after 校正运行,当: lowest landing 底层

floor selector ctr 楼层选择监控: without blocking 电梯不禁用

top floor 顶层: without impuls 无脉冲

E35-configuration 输入35配置: with relevel switches 再平层开关emergency stop as紧急停车作为: message 警告

emergency stop 紧急停车: without call cancel 不删除召唤

emergency stop as紧急停车,当: switch 开关

emerg.stop-pushb.紧急停车按键: aft. open land. Door打开厅门后允许外召open saftey circuit打开安全回路: without call cancel 外召不删除

open saftey circuit打开安全回路: without correc.trip 无校正运行

singl.fault sign.A13 : variant 1 (B+P) BP型

故障信号输出A13

direction ind."up"上行方向指示: normal 正常

direct.indic."down"下行方向指示: normal 正常

direction indicat.运行方向指示: in idle state on空闲时开

start load-time开始加载时间: with load-button加载键按下

load lift pushb.电梯加载键: car calls cancel lift-load time加载时取消轿内召唤maintenan.interval 保养期内: without blocking电梯不禁用

mainten.call-back保养返回召唤: off 关

emergency norm紧急情况规范: german 德国标准

fireman's ctr.car消防员控制轿厢: door movement normal 门正常开关

after : return to fire-man's floor 返回消防层

floor funk.E28-E32 : off 关

楼层功能输入口28-32

clearing calls 清除召唤: when arriving 当到达时