HGS-10C氢说明书V1.1版

5 启动 ........................................................................................................... 12
5.1 5.2 5.3 5.4 仪器启动与预热 ............................................................................................................................12 零点校准 ........................................................................................................................................12 量程校准 ........................................................................................................................................12 校准保存说明 ................................................................................................................................12
北京斯泰迪自控设备有限公司
HGS-10C 型氢气分析器说明书
目录
1 概述 ............................................................................................................. 1 2 工作原理 ..................................................................................................... 2
产品编号：
安装使用说明书
HGS-10C 型氢气分析器
（版本号：V1.1）
STD
北京斯泰迪自控设备有限公司
BEIJING STEAD AUTOMATION EQUIPMENT.,LTD
重要说明
使用产品之前，请认真阅读本说明！ 说明书是仪器的重要组成部分， 每次使用后请将说明书妥善保管。 其中用黑体加粗的部分请仔细阅读。用标记的部分请您注意遵守， 黑框()内诠注的部分请您务必遵守，否则可能产生不良后果。 由于仪器技术含量高、应用复杂，用户必须正确安装、使用和维 护，才能保证产品工作满足其技术规范。当用户安装、使用和维护这 些产品时，必须遵守说明书的有关规定，否则造成不良后果：如缩短 产品寿命、人身伤害、财产损失、损坏仪表及厂家保证失效等。在安 装、使用和维护这些产品之前，必须仔细阅读其说明书。如果发现说 明书有不正确或不完善的地方， 请与我公司销售部门或其他相关部门 联系，并可索取改进后的说明书或相关资料。
4 安装 ............................................................................................................. 7
4.1 开箱检查 ..........................................................................................................................................7 4.2 安全说明 ..........................................................................................................................................7 4.3 安装要求 ..........................................................................................................................................7 4.4 安装注意事项 ..................................................................................................................................7 4.5 仪器安装 ..........................................................................................................................................8 4.6 气路的安装与连接 ...........................................................................................................................8 4.7 电源的连接与保护 ..........................................................................................................................9 4.8 信号线的连接 ................................................................................................................................11
北京斯泰迪自控设备有限公司
7.3 测量显示 .........................................................................................................................................16 7.4 零点校准 .........................................................................................................................................17 7.5 量程校准 .........................................................................................................................................17 7.6 输出设置 .........................................................................................................................................18 7.7 通信设置 .........................................................................................................................................19 7.8 仪器设置 .................................................................................................................................................................................................................................. 5
3.1 3.2 3.3 3.4 3.5 应用范围 ..........................................................................................................................................5 技术指标 ..........................................................................................................................................5 工作条件 ..........................................................................................................................................5 输出信号 ..........................................................................................................................................6 基本参数 ..........................................................................................................................................6
7 画面（菜单）介绍 ................................................................................... 16
7.1 开机画面 .........................................................................................................................................16 7.2 主菜单.............................................................................................................................................16
6 菜单操作 ................................................................................................... 13
6.1 键盘操作说明 ................................................................................................................................13 6.2 屏幕对比度操作 ............................................................................................................................13 6.3 菜单快速索引 ................................................................................................................................13
2.1 2.2 2.3 2.4 气体的相对热导率 ..........................................................................................................................2 混合气体的热导率 ..........................................................................................................................2 仪器工作原理 ..................................................................................................................................2 仪器结构 ..........................................................................................................................................3