Oregon 电动橡胶擦边机设置提示说明书
合集下载
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Angle.
AGGRESSIVE SIDE PLATES Ground with too small of a grinding
wheel, or the wrong Top Plate Cutting Angle.
p. 16
8
Step 6 – Setting the vice Assembly w/“Down Angle”
Tip: Push the knob away “right away” from the operator for RH cutters until the raised line closest to the operator lines up with the triangular indicator on the vise base. Pull the knob towards operator for LH cutters, until the line furthest from the operator lines up with the triangular indicator on the vise base
4
wheel.
Step 3 – Centering the Grinder (511AX)
You may have to move the chain vice to be centered with the attachment bolt on the grinding wheel.
To move the chain vice assembly loosen the two 4mm Allan head bolts located under the chain vice. These bolts are located on each side of the “Red” adjustment knob.
6
Step 5 - Set the vice Assembly
Set the vise assembly to the manufacturers recommended top plate sharpening angle for your chain by loosening the knob and turning the vise clockwise for RH cutters counter clockwise for LH cutters.
Set the top-plate angle at 0 degrees
3
Step 2 – Centering the Grinder (511AX)
Place a carpenter square or straight edge into the chain vice pointing upwards.
5
Step 4 - Set the Grinder Head Angle
Set the grinder head angle to the manufacturers recommended Top Plate Sharpening Angle. Position the “0” reference mark on the angle desired when sharpening chains without “down Angle”. Position the “10 down” reference mark when sharpening chains with “down angle”.
9
Typical Grinding Errors
BURNED CUTTERS Grind in split second intervals with a
well dressed grinding wheel.
BACK SLOPED SIDE PLATES Ground with too large of a grinding wheel, or the wrong Top Plate Cutting
Pull the grinder head down until the
grinding wheel touches tent between chain vice
and center bolt attaching the grinding
Oregon® Grinder Setup Tips
Oregon Bench Grinder Set-up (511AX)
Grinder Head
Vise Assembly
2
Step 1 – Centering the Grinder (511AX)
Set the head angle to 90 degrees, straight up.
7
Step 6a – Setting the vice Assembly w/“Down Angle”
Loosen the knob and tilt the vice away from the operator for RH cutters. Tilt the vice towards the operator LH cutters. .
AGGRESSIVE SIDE PLATES Ground with too small of a grinding
wheel, or the wrong Top Plate Cutting Angle.
p. 16
8
Step 6 – Setting the vice Assembly w/“Down Angle”
Tip: Push the knob away “right away” from the operator for RH cutters until the raised line closest to the operator lines up with the triangular indicator on the vise base. Pull the knob towards operator for LH cutters, until the line furthest from the operator lines up with the triangular indicator on the vise base
4
wheel.
Step 3 – Centering the Grinder (511AX)
You may have to move the chain vice to be centered with the attachment bolt on the grinding wheel.
To move the chain vice assembly loosen the two 4mm Allan head bolts located under the chain vice. These bolts are located on each side of the “Red” adjustment knob.
6
Step 5 - Set the vice Assembly
Set the vise assembly to the manufacturers recommended top plate sharpening angle for your chain by loosening the knob and turning the vise clockwise for RH cutters counter clockwise for LH cutters.
Set the top-plate angle at 0 degrees
3
Step 2 – Centering the Grinder (511AX)
Place a carpenter square or straight edge into the chain vice pointing upwards.
5
Step 4 - Set the Grinder Head Angle
Set the grinder head angle to the manufacturers recommended Top Plate Sharpening Angle. Position the “0” reference mark on the angle desired when sharpening chains without “down Angle”. Position the “10 down” reference mark when sharpening chains with “down angle”.
9
Typical Grinding Errors
BURNED CUTTERS Grind in split second intervals with a
well dressed grinding wheel.
BACK SLOPED SIDE PLATES Ground with too large of a grinding wheel, or the wrong Top Plate Cutting
Pull the grinder head down until the
grinding wheel touches tent between chain vice
and center bolt attaching the grinding
Oregon® Grinder Setup Tips
Oregon Bench Grinder Set-up (511AX)
Grinder Head
Vise Assembly
2
Step 1 – Centering the Grinder (511AX)
Set the head angle to 90 degrees, straight up.
7
Step 6a – Setting the vice Assembly w/“Down Angle”
Loosen the knob and tilt the vice away from the operator for RH cutters. Tilt the vice towards the operator LH cutters. .