起亚机床常见报警

起亚机床常见报警
SKT15/21常见报警
报警号序号屏幕显⽰信息含义
2000AL-0CP & FUSE TRIP数控模块保险丝熔断2001AL-1SPINDLE AMP ALARM主轴AMP报警
2002AL-2TAILSTOCK MOTOR OVERLOAD尾座电机过载
2003AL-3LUB. OIL LACK/FAULT润滑油不⾜或压⼒报警2004AL-4HYD. PRESSURE DROP液压压⼒不⾜
2005AL-5AIR PRESSURE DROP空⽓压⼒不⾜
2006AL-6X-AXIS TORQUE ALARM X轴扭矩报警
2007AL-7Z-AXIS TORQUE ALARM Z轴扭矩报警
2008AL-8
2009AL-9
2010AL-10
2011AL-11
2012AL-12POWER OFF NC ALARM断电报警
2013AL-13DOOR OPERATION INHIBIT安全门互锁
2014AL-14SPINDLE ROTATION FAULT主轴旋转故障
2015AL-15SPINDLE COMMAND TIME OVER主轴指令超时
2016AL-16Q-SETTER ARM DOWN对⼑仪未收起
2017AL-17ROBOT FAULT机械⼿故障
2018AL-18
2019AL-19
2020AL-20ZERO RETURN INCOMPLETED回零未完成
2021AL-21
2022AL-22
2023AL-23
2024AL-24POWER OFF PROGRAM END⾃动断电程序结束2025AL-25SPINDLE ORIENTATION FAIL主轴定向失败2026AL-26
2027AL-27
2028AL-28
2029AL-29
2030AL-30CHUCK CLAMP NG卡盘未夹紧
2031AL-31DOOR CLOSE NG安全门未关
2032AL-32CENTER POSITION NG顶尖位置不对
2033AL-33SPINDLE STOP INCOMPLETED主轴未完全停⽌
2034AL-34
2035AL-35END OF BAR棒料尾端
2036AL-36COUNT UP计数结束
2037AL-37SPINDLE-DOOR INTERLOCK主轴－安全门互锁2038AL-38
2039AL-39
2040AL-40
2041AL-41TURRET INDEX INHIBIT ZONE限制⼑塔分度区域
2042AL-42HYDRULIC MOTOR OVERLOAD液压马达过载
2043AL-43COOLENT MOTOR OVERLOAD冷却马达过载
2044AL-44
2045AL-45
2046AL-46X-AXIS OVERTRAVEL X轴超程
2047AL-47Z-AXIS OVERTRAVEL Z轴超程
2048AL-48
2049AL-49
2050AL-50CHIP CONVEYOR OVERLOAD排屑器马达过载2051AL-51
2052AL-52PART CATCHER FAULT接料器故障
2053AL-53PC PARAMETER SET NG PC参数设置有误2054AL-54
2055AL-55
2056AL-56
2057AL-57
2058AL-58
2059AL-59
2060AL-60
2061AL-61
2062AL-62TURRET AMP ALARM⼑塔AMP报警
2063AL-63TURRET COMPULSORY UNCLUMP⼑塔未夹紧
2064AL-64TURRET INDEX TIME OVER⼑塔分度超时
2065AL-65COMMAND TOOL NO. NG指令⼑具号错误2066AL-66TURRET INDEX CONDITION NG⼑塔分度条件未满⾜2067AL-67
2068AL-68
2069AL-69
2070AL-70
2071AL-71
2072AL-72
2073AL-73
2074AL-74
2075AL-75TURRET ADJUST MODE进⼊⼑塔调整模式。