阀门及术语中英文对照
阀门专业术语中英文对照
阀门专业术语中英文对照1.缩写词和代号1.1 法兰结构形式及密封面代号BL---Blind Flange法兰盖LF/SE---Lapped Joint Flange对焊环松套法兰SO---Slip-On Welding Flange带颈平焊兰SW---Socket Welding Flange承插焊法兰Th---Thread Flange螺纹法兰WN---Welding Neck Flange带颈对焊法兰FF---All Flat Face全平面RF---Raised Face突面FM---Female Face凹面M---Male Face凸面T---Tongue Face榫面G---Groove Face槽面RJ---Ring Joint环连接面1.2 常用缩写词 `13Cr + STL---13Cr Trim with Stellited Seat DWD---Split Wedge Disc楔形双闸板MFR'S---Manufacturer's Standard 制造厂标准RWD---Resilient Wedge Disc弹性闸板13Cr阀芯带STL阀座"ENP---Electroless Nickel Plating 镍磷硼合金镀层NBR---Nitrile-butadiene Ruber丁腈橡胶Sch.No.---Schedule Number管表号Bana-N丁钠橡胶FE---Flanged End法兰连接端NPS---Nominal Pipe Size 管子公称尺寸（英制）STL---Stellited硬质合金（钴－铬－钨合金）BB---Bolted Bonnet螺栓连接的阀盖FLG---Flange法兰NPT---National Pipe Taper Thread 60°锥管螺纹SWD---Solid Wedge Disc楔形单闸板BC---Bolted Cap螺栓连接的阀帽FS---Forged Steel锻钢NRS---Non-Rising Stem暗杆SW----Socket Weld承插焊BN---Bayonet 卡套连接FWD---Flexible Wedge Disc 挠性楔形闸板OS---Outside Screw外螺纹TB---Thread Bonnet螺纹阀盖BRZ---Bronze青铜GALV---Galvanized 镀锌OS&Y---Outside Screw with Yoke外螺纹带支架TE---Thread End螺纹端BW---Butt Weld对焊连接HEX—六角头（螺栓）PTFE---Polytetrafluoroethylene聚四氟乙烯TC---Thread Cap 螺纹阀帽CI---Cast Iron铸铁HF---Hard Face硬表面RTFE---Reinforced PTFE增强PTFEWB---Welded Bonnet焊接阀盖CS---Carbon Steel碳钢HW---Handlewheel手轮缩写说明BE坡口BW对焊BL法兰盖BC.SWING螺栓阀盖旋启式BB.OS&Y螺栓阀盖外螺纹及轭式BC.LIFT螺栓阀盖升降式Dual-plate双蝶板FB.L.OP.全通径手工操作FB.GEAR OP.全通径齿轮操作FF全平面FL法兰F锻件GV镀锌HF硬质合金堆焊LJ活套法兰L翻边短节短规格LL翻边短节长规格MFR'S.ST'd制造商标准NPT螺纹(60O)PE平口PTFE聚四氟乙烯RPTFE增强聚四氟乙烯RF突面STR过滤器SM无缝STL硬质合金SW承插SO平焊Sch管道壁厚标号SB.ISRS螺纹阀盖内螺纹明杆ISNS内螺纹暗杆WL焊接WN带颈对焊WFR对夹Y2半硬不锈钢焊管专业名称中英文对照（一）锅炉热交换器用不锈钢钢管：stainless steel tube for boiler，heat – exchanger 材质：grade外径：OD焊接方式：welding method包装方式：packing标准：standard壁厚：wt产品应用：application捆包木箱包装：bundle or wooden case规格：specification薄壁不锈钢水管：light gauge stainless steel water pipes食品卫生不锈钢管：stainless steel sanitary tubes开卷 uncoiling活塞 loop成型 forming焊接 welding内外焊缝整平 outside inside weld bead rolling预矫正 precalibration感应热处理：induction heat treating定径矫直 sizing straightening涡流检测 eddy current test喷码 marking切断 cutting水压检查 hydrostatic test水下气压测试 under water air pressure testX射线检查 X ray inspection酸洗 pickling最终检查 final inspection发运 shipping光亮退火 bright annealing尺寸检测 dimention examination表面质量 surface examination液压试验 hydrostatic test气压测试 pneumatic test硬度测试 harness test金相组织测试分析 metallographic examination晶间腐蚀测试 intergranular corrosion test机械性能测试 mechanical property test拉伸试验 tension test压扁试验 flattering testASTM 标准下不锈钢焊管A249 关于奥氏体广泛用于热交换器，锅炉，过热器，冷凝器的焊管A269 一般用途用无缝和焊接的奥氏体不锈钢管制品标准A270 奥氏体铁素体无缝管卫生管A554 机械用焊管ASTM命名方法及扩充 (以ASTM A249为例):其中在ASTM标准下，分别有以A.B.C为首字母A：ferrous material 亚铁含铁材料黑色金属材料B：non—ferrous materials 不含铁材料有色金属材料C: cementitious materials 胶结材料ASTM A249 在A248 出版之后发展，分配可以用数字，在A25.0出现之前没有实际意义。
阀门及组件术语英汉对照表
阀门及组件术语英汉对照表一、阀门种类英汉术语对照Airvalves空气阀门AngleStopvalves角式截止阀AngleThrottleValves角式节流阀AngleTypeGlobeValves门角式截止阀Ashvalves排灰阀Aspiratingvalves吸（抽）气阀Auxiliaryvalves辅助（副）阀Balancevalves平衡阀Bellowsvalves波纹管阀Blowdownvalves泄料（放空，排污）阀Brakevalves制动阀ButterflyTypeNon-slamCheck蝶式缓冲止回阀ButterflyValveswithGearActuator蜗轮传动蝶阀Buttweldingvalves对焊连接阀Clampvalves对夹式阀门Cock二通Combinationvalves组合阀CQThreadBallValvesCQ螺纹球阀Culvertvalves地下管道阀Decelerationvalves减速阀DiaphragmValves隔膜阀Decompressionvalves泄压阀DoubleDiscFlatGateValves双闸板平板闸阀DoubleDiskParallelGateValves明杆平行式双闸板闸板DoubleOpeningExhaustValves双口排气球Drainagevalves排水阀ElectricActuatedStopValves电动截止阀ElectricActuatedWedgeGateValves电动楔式闸阀ElectricDoubleDiskParallelGateValves电动平行式双闸板闸板EmergenyCut-offValves紧急切断阀Exhaustvalves排气阀FreeFloatTypeSteamTrap浮球式疏水阀FlangeBallValves法兰球阀FlangeGateValves法兰闸阀FlangeGlobeValves法兰截止阀GaugeValves仪表阀Hand-operatedvalves手动阀HardSealButterflyValves金属密封碟阀HighTemperaturePressurePowerStationGateValves高温高压电站闸阀HighTemperaturePressurePowerStationGlobeValves高温高压电站截止阀Hydraulicrelayvalves液压继动阀LiftCheckValves升降式止回阀LiftCheckValves升降式止回阀Limitvalves限位阀LiningBallValves衬里球阀LiningButterflyValves衬里碟阀LiningCheckValves衬里止回阀LiningCock衬里二通LiningGlobeValves衬里截止阀LiningT-CockValves衬里三通旋塞阀LiquidIndicator液位计LPGPipeFitting液化气管件MagneticCo-operateGlobeValves磁耦合截止阀MagnetismForlePumps磁力泵ManualOilPumpsValves手摇油泵(阀) MeterNeedleTypeGlobeValves仪表针形截止阀ObliqueStopValves直流式截止阀ParallelSlideValves浆液阀Pintlevalve针形阀PipingCentrifugalPumps管道离心泵Plungervalves柱塞阀Pressurevalve压力（増压）阀PipingPumps管道泵PipingSafetyValves管道安全阀PlungerGlobeValves柱塞截止阀QuickDrainingValves快速排污阀RestrictorValves过流阀(或节流阀)SafetyValves安全阀ScrewPumps螺杆泵ScumGateValves排渣闸阀Solenoidvalves电磁阀SingleDiscFlatGateValves单闸板平板闸阀SingleOpeningExhaustValves单口排气球SlurryPumps泥浆泵StopValves截止阀Strainer过滤器SubmergedMotorPumps潜水电泵(排污泵)SwingCheckValves旋启式止回阀SwingCheckValves旋启式止回阀TankLorryBallValves槽车球阀T-Cock三通ThinGateValves薄型闸阀ThrottleValves节流阀TinyDragSlowShutCheckValves微阻缓闭止回阀Triple(tee)valves三通阀Two-wayvalves二通阀UnderWaterPumps液下泵VacuumPumps水力喷射器(真空泵) VerticalLiftCheckValves立式止回阀WaferCheckValves对夹式止回阀Waferplatevalves对夹蝶板阀WaferTypeButterflyValveswithRubberItning对夹式衬胶蝶阀WasteValves排污箱(阀)WaterSealGateValves水封闸阀WedgeGateValves楔式闸阀YTypeandCylinderFiltersY型筒型过滤器二、零部件英汉术语对照AxisGuide轴套Ball球、球芯Ballseat密封圈BlowdownSealingFace启、阀件密封面Body阀体Bonnet阀盖Disc阀瓣Mut螺母Screw螺栓Sealing密封件Spring弹簧Stem阀杆StemMut阀杆螺母Stemseal填料WedgeDisc闸板三、规范技术英语术语对照Applicablemedium适用介质Applicabletemperature适用温度ButtClamp对夹Chemicalanalysis化学成份Connectingformat连接形式Doubledisc双闸板Flexibledisc弹性闸板Flange法兰Hoop卡箍Insidethread内螺纹Jacket夹套Mains电源。
(完整版)阀门专业术语中英文对照
1.缩写词和代号1.1 法兰结构形式及密封面代号BL---Blind Flange 法兰盖LF/SE---Lapped Joint Flange 对焊环松套法兰SO---Slip-On Welding Flange 带颈平焊兰SW---Socket Welding Flange 承插焊法兰Th---Thread Flange 螺纹法兰WN---Welding Neck Flange 带颈对焊法兰FF---All Flat Face 全平面RF---Raised Face 突面FM---Female Face 凹面M---Male Face 凸面T---Tongue Face 榫面G---Groove Face 槽面RJ---Ring Joint 环连接面1.2 常用缩写词`13Cr + STL---13Cr Trim with Stellited Seat DWD---Split Wedge Disc 楔形双闸板MFR'S---Manufacturer's Standard 制造厂标准RWD---Resilient Wedge Disc 弹性闸板13Cr阀芯带STL阀座"ENP---Electroless Nickel Plating 镍磷硼合金镀层NBR---Nitrile-butadiene Ruber 丁腈橡胶Sch.No.---Schedule Number 管表号Bana-N 丁钠橡胶FE---Flanged End 法兰连接端NPS---Nominal Pipe Size 管子公称尺寸（英制）STL---Stellited 硬质合金（钴－铬－钨合金） BB---Bolted Bonnet 螺栓连接的阀盖FLG---Flange 法兰NPT---National Pipe Taper Thread 60°锥管螺纹SWD---Solid Wedge Disc 楔形单闸板BC---Bolted Cap 螺栓连接的阀帽FS---Forged Steel 锻钢NRS---Non-Rising Stem 暗杆SW----Socket Weld 承插焊BN---Bayonet 卡套连接FWD---Flexible Wedge Disc 挠性楔形闸板OS---Outside Screw 外螺纹TB---Thread Bonnet 螺纹阀盖BRZ---Bronze 青铜GALV---Galvanized 镀锌OS&Y---Outside Screw with Yoke 外螺纹带支架TE---Thread End 螺纹端BW---Butt Weld 对焊连接HEX—六角头（螺栓）PTFE---Polytetrafluoroethylene 聚四氟乙烯TC---Thread Cap 螺纹阀帽CI---Cast Iron 铸铁HF---Hard Face 硬表面RTFE---Reinforced PTFE 增强PTFEWB---Welded Bonnet 焊接阀盖CS---Carbon Steel 碳钢HW---Handlewheel 手轮缩写说明BE 坡口BW 对焊BL 法兰盖BC.SWING 螺栓阀盖旋启式BB.OS&Y 螺栓阀盖外螺纹及轭式BC.LIFT 螺栓阀盖升降式Dual-plate 双蝶板FB.L.OP. 全通径手工操作FB.GEAR OP. 全通径齿轮操作FF 全平面FL 法兰F 锻件GV 镀锌HF 硬质合金堆焊LJ 活套法兰L 翻边短节短规格LL 翻边短节长规格MFR'S.ST'd 制造商标准NPT 螺纹(60O)PE 平口PTFE 聚四氟乙烯RPTFE 增强聚四氟乙烯RF 突面STR 过滤器SM 无缝STL 硬质合金SW 承插SO 平焊Sch 管道壁厚标号SB.ISRS 螺纹阀盖内螺纹明杆ISNS 内螺纹暗杆WL 焊接WN 带颈对焊WFR 对夹Y2 半硬不锈钢焊管专业名称中英文对照（一）锅炉热交换器用不锈钢钢管：stainless steel tube for boiler，heat – exchanger 材质：grade外径：OD焊接方式：welding method包装方式：packing标准：standard壁厚：wt产品应用：application捆包木箱包装：bundle or wooden case规格：specification薄壁不锈钢水管：light gauge stainless steel water pipes食品卫生不锈钢管：stainless steel sanitary tubes开卷uncoiling活塞loop成型forming焊接welding内外焊缝整平outside inside weld bead rolling预矫正precalibration感应热处理：induction heat treating定径矫直sizing straightening涡流检测eddy current test喷码marking切断cutting水压检查hydrostatic test水下气压测试under water air pressure testX射线检查X ray inspection酸洗pickling最终检查final inspection发运shipping光亮退火bright annealing尺寸检测dimention examination表面质量surface examination液压试验hydrostatic test气压测试pneumatic test硬度测试harness test金相组织测试分析metallographic examination晶间腐蚀测试intergranular corrosion test机械性能测试mechanical property test拉伸试验tension test压扁试验flattering testASTM 标准下不锈钢焊管A249 关于奥氏体广泛用于热交换器，锅炉，过热器，冷凝器的焊管A269 一般用途用无缝和焊接的奥氏体不锈钢管制品标准A270 奥氏体铁素体无缝管卫生管A554 机械用焊管ASTM命名方法及扩充(以ASTM A249为例):其中在ASTM标准下，分别有以A.B.C为首字母A：ferrous material 亚铁含铁材料黑色金属材料B：non—ferrous materials 不含铁材料有色金属材料C: cementitious materials 胶结材料ASTM A249 在A248 出版之后发展，分配可以用数字，在A25.0出现之前没有实际意义。
阀门术语中英文对照
容积式压缩机positive displacement compressor往复式压缩机（活塞式压缩机）reciprocating compressor回转式压缩机rotary compressor滑片式压缩机sliding vane compressor单滑片回转式压缩机single vane rotary compressor滚动转子式压缩机rolling rotor compressor三角转子式压缩机triangle rotor compressor多滑片回转式压缩机multi-vane rotary compressor滑片blade旋转活塞式压缩机rolling piston compressor涡旋式压缩机scroll compressor涡旋盘scroll固定涡旋盘stationary scroll, fixed scroll驱动涡旋盘driven scroll, orbiting scroll斜盘式压缩机（摇盘式压缩机）swash plate compressor斜盘swash plate摇盘wobble plate螺杆式压缩机screw compressor单螺杆压缩机single screw compressor阴转子female rotor阳转子male rotor主转子main rotor闸转子gate rotor无油压缩机oil free compressor膜式压缩机diaphragm compressor活塞式压缩机reciprocating compressor单作用压缩机single acting compressor双作用压缩机double acting compressor双效压缩机dual effect compressor双缸压缩机twin cylinder compressor闭式曲轴箱压缩机closed crankcase compressor开式曲轴箱压缩机open crankcase compressor顺流式压缩机uniflow compressor逆流式压缩机return flow compressor干活塞式压缩机dry piston compressor双级压缩机compound compressor多级压缩机multistage compressor差动活塞式压缩机stepped piston compound compressor, differential piston compressor 串轴式压缩机tandem compressor, dual compressor截止阀line valve, stop valve排气截止阀discharge line valve吸气截止阀suction line valve部分负荷旁通口partial duty port能量调节器energy regulator容量控制滑阀capacity control slide valve容量控制器capacity control消声器muffler联轴节coupling曲轴箱crankcase曲轴箱加热器crankcase heater轴封crankcase seal, shaft seal填料盒stuffing box轴封填料shaft packing机械密封mechanical seal波纹管密封bellows seal转动密封rotary seal迷宫密封labyrinth seal轴承bearing滑动轴承sleeve bearing偏心环eccentric strap滚珠轴承ball bearing滚柱轴承roller bearing滚针轴承needle bearing止推轴承thrust bearing外轴承pedestal bearing臼形轴承footstep bearing轴承箱bearing housing止推盘thrust collar偏心销eccentric pin曲轴平衡块crankshaft counterweight, crankshaft balance weight 曲柄轴crankshaft偏心轴eccentric type crankshaft曲拐轴crank throw type crankshaft连杆connecting rod连杆大头crank pin end连杆小头piston pin end曲轴crankshaft主轴颈main journal曲柄crank arm, crank shaft曲柄销crank pin曲拐crank throw曲拐机构crank-toggle阀盘valve disc阀杆valve stem阀座valve seat阀板valve plate阀盖valve cage阀罩valve cover阀升程限制器valve lift guard阀升程valve lift阀孔valve port吸气口suction inlet压缩机气阀compressor valve吸气阀suction valve排气阀delivery valve圆盘阀disc valve环片阀ring plate valve簧片阀reed valve舌状阀cantilever valve条状阀beam valve提升阀poppet valve菌状阀mushroom valve杯状阀tulip valve缸径cylinder bore余隙容积clearance volume附加余隙（补充余隙）clearance pocket活塞排量swept volume, piston displacement理论排量theoretical displacement实际排量actual displacement实际输气量actual displacement, actual output of gas 气缸工作容积working volume of the cylinder活塞行程容积piston displacement气缸cylinder气缸体cylinder block气缸壁cylinder wall水冷套water cooled jacket气缸盖（气缸头）cylinder head安全盖（假盖）safety head假盖false head活塞环piston ring气环sealing ring刮油环scraper ring油环scrape ring活塞销piston pin活塞piston活塞行程piston stroke吸气行程suction stroke膨胀行程expansion stroke压缩行程compression stroke排气行程discharge stroke升压压缩机booster compressor立式压缩机vertical compressor卧式压缩机horizontal compressor角度式压缩机angular type compressor对称平衡型压缩机symmetrically balanced type compressor CQ螺纹球阀CQ Thread Ball ValvesL形三通式L-pattern three wayT形三通式T-pattern three way安全阀Safety valve暗杆闸阀Inside screw nonrising stem type gate valve百叶窗;闸板shutter百叶窗式挡板louver damper摆阀式活塞泵swing gate piston pump保温式Steam jacket type报警阀alarm valve报警阀;信号阀;脉冲阀sentinel valve背压调节阀back pressure regulating valve背压率Rate of back pressuec本体阀杆密封body stem seal波纹管阀Bellows valves波纹管密封阀bellow sealed valve波纹管密封式Bellows seal type波纹管平衡式安全阀Bellows seal balance safety valve波纹管式减压阀Bellows reducing valve波纹管式减压阀Bellows weal reducing valve薄膜thin film薄膜;隔膜diaphragm薄膜式减压阀Diapjragm reducing valve薄型闸阀Thin Gate Valves不封闭式Unseal type槽车球阀Tank Lorry Ball Valves颤振Flutter常闭式Normally closed type常开式Normally open type超低温阀门Cryogenic valve超高压阀门Super high pressure valve超过压力Overpressure of a safety valve衬胶隔膜阀rubber lined diaphragm衬胶截止阀rubber lined globe valve垂直板式蝶阀Vertical disc type butterfly valve磁耦合截止阀Magnetic Co-operate Globe Valves带补充载荷的安全阀Supplementary loaded safety valve带辅助装置的安全阀Assisted safety valve单阀碟双面平行密封闸阀parallel single disk gate valve单口排气阀Single Opening Exhaust Valves单向阀Non-return Valve单闸板Single gate disc单闸板平板闸阀Single Disc Flat Gate Valves弹簧薄膜式减压阀Spring diaphragm reducing valve弹簧式安全阀Direct spring loaded safety valve弹簧座Spring plate弹性闸板Flexible gate disc当量计算排量Equivalent calculated capacity挡板damper导阀Pilot valve导向套Valve guide disc guide低温阀门Sub-zero valve低压阀门Low pressure valve底阀bottom valve底阀Foot valve电磁动装置Eletro magnetic actuator电磁阀magnetic valve电磁阀solenoid valve电磁－液动装置Eletro magnetichydraulic actuator电动阀mortor operated valve电动阀motorized valve电动截止阀Electric Actuated Stop Valves电动平行式双闸板闸板Electric Double Disk Parallel Gate Valves 电动楔式闸阀Electric Actuated Wedge Gate Valves电动装置Electric actuator电－液动装置Eletro hydraulic actuator电液伺服阀electro-hydraulic servovalve调节弹簧Regulation spring调节阀adjusting valve调节阀control valve调节阀regulating valve调节螺套Adjusting bolt Adjusting screw调节圈Adjusting ring蝶板Disc蝶阀；瓣阀butterfly valve蝶阀；瓣阀；拍门；铰链阀flap valve蝶式缓冲止回阀Butterfly Type Non-slam Check蝶式止回阀Butterfly swing check valve定比减压阀Proprutioning pressure reducing valve定差减压阀Fixed differential reducing valve定值减压阀Fixed pressure reducing valve动态特性Dynamic characteristics对焊连接阀Buttwelding valves对夹蝶板阀Wafer plate valves对夹式衬胶蝶阀Wafer Type Butterfly Valves with Rubber Itning对夹式阀门Clamp valves对夹式止回阀Wafer Check Valves额定排量Certified capacity额定排量系数Derated coefficient of discharge 二通阀Two-way valves阀valve阀板valve deck plate阀板valve plate阀板式活塞泵valve deck plate type piston pump 阀板式活塞泵valve plate type piston pump阀瓣Disc阀操纵杆valve operating rod阀痤槽valve seat recess阀挡valve grid阀挡valve positioner阀挡valve stop阀导杆valve tail rod阀导向器valve guide阀盖bonnet阀盖衬套bonnet bush阀盖垫片bonnet gasket阀杆stem阀杆valve rod阀杆valve spindle阀杆端部尺寸Dimmension of valve stem end阀杆环stem ring阀杆螺母Yoke bushing Yoke nut阀杆填料stem packing阀杆头部尺寸Dimension of valve stem head阀簧valve spring阀簧压板valve spring plate阀控水锤泵valve-controlled hydraulic ram阀框架valve yoke阀门Valve阀门传动装置valve bandle set阀门和管件Valves and Fittings阀门盘根valve packing阀门手柄valve handle阀盘disc阀盘valve disc阀片Disc阀球valve ball阀驱动臂valve driving arm阀驱动臂valve motion arm阀式活塞valve type piston阀式活塞valve type bucket阀室式活塞泵valve box type piston pump阀室式活塞泵（美）valve pot type piston pump阀抬起装置valve lifting device阀体body阀体valve body阀箱valve box阀箱valve cage阀箱valve chest阀箱；阀限位器valve guard阀箱盖cover for valve box阀箱盖valve box cover阀箱式活塞泵（美）turret type piston pump阀形活塞泵valve type piston pump阀座Seat ring阀座valve carrier阀座valve seat(body seat)阀座；阀盘valve seat阀座环seat ring阀座密封嵌条sealing strip for valve seat法兰flange法兰堵头blind flange法兰端flange end法兰接头flange joint法兰连接紧固件（双头螺栓和螺帽）flange bolting 法兰密封面，法兰面flange facing法兰面加工flange facing finish法兰球阀Flange Ball Valves翻板阀Flap反冲盘Disc holder反向作用式减压阀Reverse acting reducing valve反向作用式减压阀Reverse acting reducing valve放空阀emptying valve放气阀air vent valve;vent valve放气阀；排气阀air evacuation valve放泄阀escape valve分置阀室式活塞泵separate valve box type piston pump 分置阀室式活塞泵（美）side pot type piston pump封闭式Seal type浮动式球阀Float ball valve浮球Ball float浮球阀Float Valve阀门种类中英文对照中文英文中文英文阀门valve 通用阀门General valve球阀Ball valve 槽车球阀Tank Lorry Ball ValvesCQ 螺纹球阀CQ Thread Ball Valves 法兰球阀Flange Ball Valves衬里球阀Lining Ball Valves API球阀API Ball valves浮动球阀Float Ball valves 固定球阀Trunnion-mounted Ball valves三通法兰球阀Three Ball valves V 型调节球阀V-Regulating Ball valves闸阀Gate valve 楔式闸阀Wedge Gate Valves法兰闸阀Flange Gate Valves 排渣闸阀Scum Gate V alves薄型闸阀Thin Gate Valves 水封闸阀Water Seal Gate Valves电动楔式闸阀Electric Actuated Wedge Gate Valves 平板闸阀Flat Gate Valve单闸板平板闸阀Single Disc Flat Gate Valves 电动平行式双闸板闸阀Electric Double Disk Parallel Gate Valves双闸板平板闸阀Double Disc Flat Gate Valves 明杆平行式双闸板闸阀Double Disk Parallel Gate Valves截止阀Globe valve 角式截止阀Angle Globe valves门角式截止阀Angle Type Globe V alves 电动截止阀Electric Actuated Stop V alves法兰截止阀Flange Globe Valves 衬里截止阀Lining Globe V alves直流式截止阀Oblique Stop Valves 柱塞截止阀Plunger Globe Valves止回阀Check valve 旋启式止回阀Swing Check Valves对夹式止回阀Wafer Check Valves 蝶式缓冲止回阀Butterfly Type Non-slam Check蝶式缓冲止回阀Butterfly Type Non-slam Check 升降式止回阀Lift Check Valves衬里止回阀Lining Check Valves 微阻缓闭止回阀Tiny Drag Slow Shut Check V alves立式止回阀Vertical Lift Check Valves蝶阀Butterfly Valve 对夹蝶板阀Wafer plate valve衬里蝶阀Lining Butterfly Valves 蜗轮传动蝶阀Butterfly Valves with Gear Actuator对夹式衬胶蝶阀Wafer Type Butterfly Valves with Rubber Itning 金属密封蝶阀Hard Seal Butterfly Valves隔膜阀diaphragm valve 旋塞阀plug valve安全阀safety valve 管道安全阀Piping Safety Valves回转阀rotary valve 减压阀pressure reducing valve减速阀Deceleration valves 泄压阀Decompression valves蒸汽疏水阀Automatic steam trap valve 组合阀Combination valves针形阀Pintle valve 仪表阀Gauge Valves仪表针形截止阀Meter Needle Type Globe Valves 空气阀门Air valves排灰阀Ash valves 吸（抽）气阀Aspirating valves辅助（副）阀Auxiliary valves 平衡阀Balance valves波纹管阀Bellows valves 泄料（放空，排污）阀Blowdown valves制动阀Brake valves 对焊连接阀Buttwelding valves地下管道阀Culvert valves 双口排气球Double Opening Exhaust Valves排水阀Drainage valves 紧急切断阀Emergeny Cut-off Valves排气阀Exhaust valves 浮球式疏水阀Free Float Type Steam Trap手动阀Hand-operated valves 液压继动阀Hydraulic relay valves限位阀Limit valves 衬里三通旋塞阀Lining T-Cock Valves 液位计Liquid Indicator 浆液阀Parallel Slide Valves柱塞阀Plunger valves 压力（増压）阀Pressure valve快速排污阀Quick Draining Valves 电磁阀Solenoid valves 过滤器Strainer 节流阀Throttle Valves阀门术语中英文对照中文英文口径bore公称通径Nominal diameter公称压力Nominal pressure工作温度Operating temperature工作压差Operating pressure工作背压Operating back pressure关闭压力Lockup pressure开启高度Lift壳体试验Shell test壳体试验压力Seal test pressure连接尺寸Conncetion cimension连接形式Type of connection流道面积Flow area流道直径Flow diameter流量孔板flow orifice plate流量特性Flow characteristics流量特性偏差Flow characteristics derivation漏汽量Steam loss密封面Sealing face密封试验Seal test密封试验压力Seal test pressure上密封Back seat上密封试验Back seal test适用介质Suitable medium适用温度Suitable temperature最大过冷度Maximum subcoold temperature最大流量Maximum flow rate最大压差Maximum differential pressure最低工作压力Minimum operating pressure最高背压率Maximum rate of back pressure最高允许压力Maximum allowable pressure最小过冷度Minimum subcooled temperature最小压差Minimum differntial pressure常闭式Normally closed type常开式Normally open type阀门零配件中英文对照中文英文阀体body阀盖bonnet阀盖垫片bonnet gasket阀盖衬套bonnet bush阀瓣Disc阀箱valve box阀座Seat ring阀杆Stem阀杆螺母Yoke bushing Yoke nut 法兰flange填料Packing填料垫Packing seat密封件Sealing挡板damper导向套Valve guide disc guide弹簧座Spring plate轴套Axis Guide球、球芯Ball密封圈Ball seat螺母Mut螺栓Screw弹簧Spring闸板Wedge Disc。
阀门种类英汉术语对照
阀门种类英汉术语对照Air valves 空气阀门Angle Stop valves 角式截止阀Angle Throttle Valves 角式节流阀Angle Type Globe Valves 门角式截止阀Ash valves 排灰阀Aspirating valves 吸（抽）气阀Auxiliary valves 辅助（副）阀Balance valves 平衡阀Bellows valves 波纹管阀Blowdown valves 泄料（放空，排污）阀Brake valves 制动阀Butterfly Type Non-slam Check 蝶式缓冲止回阀Butterfly Valves with Gear Actuator 蜗轮传动蝶阀Buttwelding valves 对焊连接阀Clamp valves 对夹式阀门Cock 二通Combination valves 组合阀CQ Thread Ball Valves CQ螺纹球阀Culvert valves 地下管道阀Deceleration valves 减速阀Diaphragm Valves 隔膜阀Decompression valves 泄压阀Double Disc Flat Gate Valves 双闸板平板闸阀Double Disk Parallel Gate Valves明杆平行式双闸板闸板Double Opening Exhaust Valves 双口排气球Drainage valves 排水阀Electric Actuated Stop Valves 电动截止阀Electric Actuated Wedge Gate Valves电动楔式闸阀Electric Double Disk Parallel Gate Valves电动平行式双闸板闸板 Emergeny Cut-off Valves 紧急切断阀Exhaust valves 排气阀Free Float Type Steam Trap 浮球式疏水阀Flange Ball Valves 法兰球阀Flange Gate Valves 法兰闸阀Flange Globe Valves 法兰截止阀Gauge Valves 仪表阀Hand-operated valves 手动阀Hard Seal Butterfly Valves 金属密封碟阀High Temperature Pressure Power Station Gate Valves 高温高压电站闸阀High Temperature Pressure Power Station Globe Valves 高温高压电站截止阀 Hydraulic relay valves 液压继动阀Lift Check Valves 升降式止回阀Lift Check Valves 升降式止回阀Limit valves 限位阀Lining Ball Valves 衬里球阀Lining Butterfly Valves 衬里碟阀Lining Check Valves 衬里止回阀Lining Cock 衬里二通Lining Globe Valves 衬里截止阀Lining T-Cock Valves 衬里三通旋塞阀Liquid Indicator 液位计LPG Pipe Fitting 液化气管件Magnetic Co-operate Globe Valves磁耦合截止阀Magnetism Forle Pumps 磁力泵Manual Oil Pumps Valves 手摇油泵(阀)Meter Needle Type Globe Valves 仪表针形截止阀Oblique Stop Valves 直流式截止阀Parallel Slide Valves 浆液阀Pintle valve 针形阀Piping Centrifugal Pumps 管道离心泵Plunger valves 柱塞阀Pressure valve 压力（増压）阀Piping Pumps 管道泵Piping Safety Valves 管道安全阀Plunger Globe Valves 柱塞截止阀Quick Draining Valves 快速排污阀Restrictor Valves 过流阀(或节流阀)Safety Valves 安全阀Screw Pumps 螺杆泵Scum Gate Valves 排渣闸阀Solenoid valves 电磁阀Single Disc Flat Gate Valves 单闸板平板闸阀Single Opening Exhaust Valves 单口排气球Slurry Pumps 泥浆泵Stop Valves 截止阀Strainer 过滤器Submerged Motor Pumps 潜水电泵(排污泵)Swing Check Valves 旋启式止回阀Swing Check Valves 旋启式止回阀Tank Lorry Ball Valves 槽车球阀T-Cock 三通Thin Gate Valves 薄型闸阀Throttle Valves 节流阀Tiny Drag Slow Shut Check Valves 微阻缓闭止回阀Triple (tee) valves 三通阀Two-way valves 二通阀Under Water Pumps 液下泵Vacuum Pumps 水力喷射器(真空泵)Vertical Lift Check Valves 立式止回阀Wafer Check Valves 对夹式止回阀Wafer plate valves 对夹蝶板阀Wafer Type Butterfly Valves with Rubber Itning对夹式衬胶蝶阀 Waste Valves 排污箱(阀)Water Seal Gate Valves 水封闸阀Wedge Gate Valves 楔式闸阀Y Type and Cylinder Filters Y型筒型过滤器阀门零部件英汉术语对照Axis Guide 轴套Ball 球、球芯Ball seat 密封圈Blowdown Sealing Face 启、阀件密封面Body 阀体Bonnet 阀盖Disc 阀瓣Mut 螺母Screw 螺栓Sealing 密封件Spring 弹簧Stem 阀杆Stem Mut 阀杆螺母Stem seal 填料Wedge Disc 闸板阀门规技术英语术语对照Applicable medium 适用介质Applicable temperature 适用温度Butt Clamp 对夹Chemical analysis 化学成份Connecting format 连接形式Double disc 双闸板Flexible disc 弹性闸板Flange 法兰 Hoop 卡箍Inside thread 螺纹Jacket 夹套Mains 电源Material chemical analysis and mechanical capacity材料化学成份和机械性能 materials 材料 Materials for main parts 主要零件材料Mechanical capacity 机械性能Max. Discharging Capacity 最大排水量Max. Operating Temperature 最高工作温度Max. Allowable Temperature 最高允许温度Max. Allowable Pressure 最高允许压力Model 型号Name of parts 零件名称nitrogen (N) 氮Nominal bore 公称通径Nominal Pressure 公称压力Nozzle 排气口Outside thread 外螺纹Oxidant 氧化性介质Parallel 平行Piping 管路Piston 活塞Reductant 还原性介质Rising stem 明杆Seal 阀座，密封面Seat testing pressure 压力气密封试验压力Socket 卡套Specifications 性能规Single disc 单闸板Solid 刚性Strengh testing pressure 强度试验压力Steam , condensate 蒸汽,凝结水Stroke 冲程，行程Water,oil,steam 水,温度,气Wedge 楔式 Welding 焊接阀门材质术语英汉对照Atbas metal 镍铬钢Buna-N rubber 丁晴橡胶Casting aluminium brass 铸铝黄铜Casting aluminium bronze 铸铝青铜Ceramic metal 瓷金属Chromel alloy 镍铬合金CHR rubber 氯晴橡胶Chrominm-molybdenum-vanadium steel 铬钼钒钢 Chromium stainless steel 铬不锈钢Chromium-molybdenum steel 铬钼钢Corrugation pad 波形垫Cuprum alloy 铜合金Ductile Cast iron 球墨铸铁Expanded graphite 柔性石墨Fine Steel Casting iron 优质碳素钢Fluorous rubber 氟橡胶Gray Cast iron 灰铸铁Hayne's alloy 钴铬钨合金High tem perature steel 高温钢Monel 蒙乃尔合金Low temperature steel 低温钢Nylon 尼龙塑料Polytetrafluoroethylene(PTEF) 聚四氟乙烯Polythene 聚乙烯Pure aluminium 纯铝Pure cupper 纯铜Rubber graphite board 橡胶石墨板Spring steel 弹簧钢Stainless acid-resisting steel 不锈耐酸钢 Stainless and Graphite 不锈钢/石墨Stainless steel 不锈钢Steel Casting iron 碳素钢铸件Shell Test Pressure 壳体试验压力Service Fluid 工作介质3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting & holding furnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws & nuts 螺栓,螺帽与螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软)板(片)材与自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal & vertical 卧式与立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & horizontal 立式与卧式铣床Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P型PVC高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe & tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 自动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches & buttons 开关与按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手。
阀门名词术语中英文对照
阀门名词术语中英文对照阀门valve闸阀 gate valve截止阀globe valve, stop valve节流阀throttle valve球阀ball valve蝶阀butterfly valve隔膜阀 diaphragm valve旋塞阀plug valve止回阀check valve, non-return valve安全阀safety valve, pressure减压阀pressure reducing valve疏水阀steam trap排污阀 blow-down valve调节阀(控制阀)control valve, adjusting valve 分配阀 dividing valve混合阀 mixing valve水力控制阀 hydraulic control valve手动阀门 manual operated valve电动阀门 electrical operated valve气动阀门 pneumatically operated valve 低压阀门 low pressure valve中压阀门 middle pressure valve高压阀门 high pressure valve超高压阀门 super high pressure valve 高温阀门 high temperature valve中温阀门 moderate temperature valve 常温阀门 normal temperature valve低温阀门 sub-zero valve超低温阀门 cryogenic valve结构长度 face-to-face dimension结构形式 type of construction直通式 through way type角式 angle type直流式 y-type三通式 three way typeT形三通式 T-pattern three wayL形三通式 L-pattern three way平衡式 balance type杠杆式 lever type常开式 normally open type 常闭式normally closed type保温式 steam jacket type波纹管式 bellows seal type全径阀门 full-port valve缩径阀门 reduced-port valve缩口阀门 reduced-bore valve单向阀门 unidirectional valve双向阀门 bidirectional valve上密封back seal压力密封pressure seal连接形式 type of connection壳体 shell阀体body阀盖bonnet启闭件disc阀座seat密封面 sealing face，surface阀杆 stem, spindle阀杆螺母yoke nut填料函（填料箱）stuffing box填料packing, packing rings填料垫packing seat, packing washer支架 yoke撞击手轮impact hand wheel阀瓣（阀芯） disc（valve core）楔式闸阀wedge gate valve闸板wedge单闸板single gate刚性闸版 rigid gate弹性闸板 flexible gate disc双闸板double gate楔式双闸板 wedge double gate平行式双闸板 parallel double gate浮动式球阀floating ball valve固定式球阀fixed ball valve球体 ball斜板式蝶阀inclined disc butterfly valve 蝶板 disc屋脊式隔膜阀weir diaphragm valve截止式隔膜阀 globe diaphragm valve隔膜diaphragm填料式旋塞阀 gland packing plug valve 油封式旋塞阀 lubricated plug valve塞子 plug升降式止回阀 lift check valve升降立式止回阀 vertical lift check valve 旋启式止回阀 swing check valve底阀 foot valve，bottom valve轴流式止回阀 axial flow check valve蝶式止回阀 butterfly swing check valve 销轴 hinge pin摇杆 arm先导式安全阀 pilot operated safety valve 全启式安全阀 full lift safety valve微启式安全阀 low lift safety valve双联弹簧式安全阀duplex safety valve真空安全阀vacuum relief valve敞开式安全阀openly sealed safety valve调节螺母adjusting screw弹簧座 spring plate导向套 dise guide反冲盘 disc holder调节圈 adjusting ring压力释放装置pressure relief device爆破片装置bursting disk device折断销装置breaking pin device弯折销装置buckling pin device剪切销装置shear pin device易熔塞装置fusible plug device排放面积discharge area流道面积flow area流道直径flow diameter帘面积curtain area开启高度lift额定开高rated lift密封面斜角seat angle密封面积seat area密封面平均直径seat mean diameter净流通面积net flow area喉径 throat diameter整定压力set pressure超过压力overpressure回座压力reseating pressure启闭压差blowdown排放压力 relieving pressure排放背压力 built-up back pressure附加背压力 superimposed back pressure理论排量 theoretical discharge capacity 额定排量 certified (discharge) capacity 频跳 chatter颤振 flutter封闭式 seal type非封闭式 unseal type在用试验in-service testing工作台上定压试验bench testing薄膜式减压阀 diaphragm reducing valve活塞式减压阀 piston reducing valve杠杆式减压阀 lever reducing valve膜片 diaphragm浮球式疏水阀 ball float steam trap浮桶式疏水阀 open bucket steam trap脉冲式疏水阀 impulse steam trap热动力式疏水阀 thermodynamic steam trap 蒸汽疏水阀 steam trap工作压力 operating pressure最高工作压力 maximum operating pressure 最低工作压力 minimum operating pressure 工作背压 operating back pressure背压率 rate of back pressure最大压差 maximum differential pressure最小压差 minimum differential pressure开阀温度 operating valve temperature关阀温度 closing valve temperature过冷度 subcooled temperature最小过冷度 minimum subcooled temperature 冷凝结水排量 cold condensate capacity热凝结水排量 hot condensate capacity漏汽量 steam loss无负荷漏汽量 unload steam loss 有负荷漏汽量 load steam loss无负荷漏汽率 rate of unload steam loss有负荷漏汽率 rate of load steam loss负荷率 rate of load condensate阀片 disc钟形罩 inverted bucket浮球 float ball浮桶 float bucket执行机构 actuator基本误差 intrinsic error回差 hysteresis error死区 dead band行程 travel额定行程 rated travel相对行程（h） relative travel（h）额定行程偏差 deviation of rated travel额定流量（Q） rated flow（Q）泄漏量 leakage流量系数 flow coefficient额定流量系数（K V）rated flow coefficient（K V）相对流量系数（Φ）relative flow coefficient（Φ）固有流量特性 inherent flow characteristic 可调比（R） inherent rangea bility（R）阻塞流 choked flow斜率偏差 slope deviation遥控浮球阀remote float control valve水利控制减压阀 pressure reducing valve缓闭止回阀 low speed closed check valve 持压/泄压阀 pressure sustaining ,relief valve 水泵控制阀 pump control valve最小开启压力 minimum open pressure驱动装置 actuator多回转驱动装置multi-turn actuator部分回转驱动装置part-turn actuator电动装置electric actuator气动装置pneumatic actuator直线型气动装置 linear pneumatic actuator回转型气动装置rotary pneumatic actuator气动装置的行程stroke of pneumatic actuator 液压驱动装置 hydraulic actuator电磁驱动装置 electro magnetic actuator 电-液联动装置electro hydraulic actuator气-液驱动装置pneumatic-hydraulic actuator 蜗轮传动装置 worm gear actuator正齿轮传动装置cylindrical gear actuator锥齿轮传动装置conical gear actuator转矩torque推力thrust壳体试验 shell test壳体试验压力 shll test pressure密封试验 seal test密封试验压力 seal test pressure上密封试验 back seal test静压寿命试验potential pressure life test耐火试验 fire test防静电试验 anti-static test主要性能参数specification公称压力nominal pressure公称尺寸nominal diameter工作压力 working pressure最高工作压力 maximum operating pressure工作温度 working temperature最高工作温度 maximum operating temperature 泄漏量 leakage吻合度 percent of contact area连接尺寸 connection dimension最大压差 maximum pressure differential 位置指示器 position indicator压力边界 pressure boundary。
阀门种类英汉术语对照
阀门种类英汉术语对照Air valves 空气阀门Angle Stop valves 角式截止阀Angle Throttle Valves 角式节流阀Angle Type Globe Valves 门角式截止阀Ash valves 排灰阀Aspirating valves 吸（抽）气阀Auxiliary valves 辅助（副）阀Balance valves 平衡阀Bellows valves 波纹管阀Blowdown valves 泄料（放空，排污）阀Brake valves 制动阀Butterfly Type Non-slam Check 蝶式缓冲止回阀 Butterfly Valves with Gear Actuator 蜗轮传动蝶阀 Buttwelding valves 对焊连接阀Clamp valves 对夹式阀门Cock 二通Combination valves 组合阀CQ Thread Ball Valves CQ螺纹球阀Culvert valves 地下管道阀Deceleration valves 减速阀Diaphragm Valves 隔膜阀Decompression valves 泄压阀Double Disc Flat Gate Valves 双闸板平板闸阀 Double Disk Parallel Gate Valves明杆平行式双闸板闸板Double Opening Exhaust Valves 双口排气阀Drainage valves 排水阀Electric Actuated Stop Valves 电动截止阀Electric Actuated Wedge Gate Valves电动楔式闸阀Electric Double Disk Parallel Gate Valves电动平行式双闸板闸板Emergeny Cut-off Valves 紧急切断阀Exhaust valves 排气阀Free Float Type Steam Trap 浮球式疏水阀Flange Ball Valves 法兰球阀Flange Gate Valves 法兰闸阀Flange Globe Valves 法兰截止阀Gauge Valves 仪表阀Hand-operated valves 手动阀Hard Seal Butterfly Valves 金属密封碟阀High Temperature Pressure Power Station Gate Valves 高温高压电站闸阀High Temperature Pressure Power Station Globe Valves 高温高压电站截止阀Hydraulic relay valves 液压继动阀Lift Check Valves 升降式止回阀Lift Check Valves 升降式止回阀Limit valves 限位阀Lining Ball Valves 衬里球阀Lining Butterfly Valves 衬里碟阀Lining Check Valves 衬里止回阀Lining Cock 衬里二通Lining Globe Valves 衬里截止阀Lining T-Cock Valves 衬里三通旋塞阀Liquid Indicator 液位计LPG Pipe Fitting 液化气管件Magnetic Co-operate Globe Valves磁耦合截止阀 Magnetism Forle Pumps 磁力泵Manual Oil Pumps Valves 手摇油泵（阀）Meter Needle Type Globe Valves 仪表针形截止阀 Oblique Stop Valves 直流式截止阀Parallel Slide Valves 浆液阀Pintle valve 针形阀Piping Centrifugal Pumps 管道离心泵Plunger valves 柱塞阀Pressure valve 压力（増压）阀Piping Pumps 管道泵Piping Safety Valves 管道安全阀Plunger Globe Valves 柱塞截止阀Quick Draining Valves 快速排污阀Restrictor Valves 过流阀（或节流阀）Safety Valves 安全阀 Screw Pumps 螺杆泵Scum Gate Valves 排渣闸阀Solenoid valves 电磁阀Single Disc Flat Gate Valves 单闸板平板闸阀 Single Opening Exhaust Valves 单口排气阀Slurry Pumps 泥浆泵Stop Valves 截止阀Strainer 过滤器Submerged Motor Pumps 潜水电泵（排污泵）Swing Check Valves 旋启式止回阀Swing Check Valves 旋启式止回阀Tank Lorry Ball Valves 槽车球阀T-Cock 三通Thin Gate Valves 薄型闸阀Throttle Valves 节流阀Tiny Drag Slow Shut Check Valves 微阻缓闭止回阀 Triple （tee） valves 三通阀Two-way valves 二通阀Under Water Pumps 液下泵Vacuum Pumps 水力喷射器（真空泵）Vertical Lift Check Valves 立式止回阀Wafer Check Valves 对夹式止回阀Wafer plate valves 对夹蝶板阀Wafer Type Butterfly Valves with Rubber Itning对夹式衬胶蝶阀Waste Valves 排污箱（阀）Water Seal Gate Valves 水封闸阀Wedge Gate Valves 楔式闸阀Y Type and Cylinder Filters Y型筒型过滤器阀门零部件英汉术语对照Axis Guide 轴套Ball 球、球芯Ball seat 密封圈Blowdown Sealing Face 启、阀件密封面Body 阀体Bonnet 阀盖Disc 阀瓣Mut 螺母Screw 螺栓Sealing 密封件Spring 弹簧Stem 阀杆Stem Mut 阀杆螺母Stem seal 填料Wedge Disc 闸板阀门规范技术英语术语对照Applicable medium 适用介质 Applicable temperature 适用温度Butt Clamp 对夹Chemical analysis 化学成份Connecting format 连接形式Double disc 双闸板Flexible disc 弹性闸板Flange 法兰 Hoop 卡箍Inside thread 内螺纹Jacket 夹套Mains 电源Material chemical analysis and mechanical capacity 材料化学成份和机械性能materials 材料 Materials for main parts 主要零件材料Mechanical capacity 机械性能Max. Discharging Capacity 最大排水量Max. Operating Temperature 最高工作温度Max. Allowable Temperature 最高允许温度Max. Allowable Pressure 最高允许压力Model 型号Name of parts 零件名称nitrogen （N） 氮Nominal bore 公称通径Nominal Pressure 公称压力Nozzle 排气口Outside thread 外螺纹Oxidant 氧化性介质Parallel 平行Piping 管路Piston 活塞Reductant 还原性介质Rising stem 明杆Seal 阀座，密封面Seat testing pressure 压力气密封试验压力 Socket 卡套Specifications 性能规范Single disc 单闸板Solid 刚性Strengh testing pressure 强度试验压力 Steam ， condensate 蒸汽，凝结水Stroke 冲程，行程Water，oil，steam 水，温度，气Wedge 楔式 Welding 焊接阀门材质术语英汉对照Atbas metal 镍铬钢Buna-N rubber 丁晴橡胶Casting aluminium brass 铸铝黄铜Casting aluminium bronze 铸铝青铜 Ceramic metal 陶瓷金属 Chromel alloy 镍铬合金CHR rubber 氯晴橡胶Chrominm-molybdenum-vanadium steel 铬钼钒钢 Chromium stainless steel 铬不锈钢 Chromium-molybdenum steel 铬钼钢 Corrugation pad 波形垫Cuprum alloy 铜合金Ductile Cast iron 球墨铸铁Expanded graphite 柔性石墨Fine Steel Casting iron 优质碳素钢Fluorous rubber 氟橡胶Gray Cast iron 灰铸铁Hayne's alloy 钴铬钨合金High tem perature steel 高温钢Monel 蒙乃尔合金Low temperature steel 低温钢Nylon 尼龙塑料Polytetrafluoroethylene（PTEF） 聚四氟乙烯 Polythene 聚乙烯Pure aluminium 纯铝Pure cupper 纯铜Rubber graphite board 橡胶石墨板Spring steel 弹簧钢Stainless acid-resisting steel 不锈耐酸钢Stainless and Graphite 不锈钢/石墨Stainless steel 不锈钢Steel Casting iron 碳素钢铸件Shell Test Pressure 壳体试验压力Service Fluid 工作介质Air valves 空气阀门Angle Stop valves 角式截止阀Angle Throttle Valves 角式节流阀Angle Type Globe Valves 门角式截止阀 Ash valves 排灰阀Aspirating valves 吸（抽）气阀Auxiliary valves 辅助（副）阀Balance valves 平衡阀Bellows valves 波纹管阀Blowdown valves 泄料（放空，排污）阀 Brake valves 制动阀Butterfly Type Non-slam Check 蝶式缓冲止回阀Butterfly Valves with Gear Actuator 蜗轮传动蝶阀Buttwelding valves 对焊连接阀Clamp valves 对夹式阀门Cock 二通Combination valves 组合阀CQ Thread Ball Valves CQ螺纹球阀 Culvert valves 地下管道阀Deceleration valves 减速阀Diaphragm Valves 隔膜阀Decompression valves 泄压阀Double Disc Flat Gate Valves 双闸板平板闸阀Double Disk Parallel Gate Valves明杆平行式双闸板闸板Double Opening Exhaust Valves 双口排气球 Drainage valves 排水阀Electric Actuated Stop Valves 电动截止阀 Electric Actuated Wedge Gate Valves电动楔式闸阀Electric Double Disk Parallel Gate Valves 电动平行式双闸板闸板 Emergeny Cut-off Valves 紧急切断阀 Exhaust valves 排气阀Free Float Type Steam Trap 浮球式疏水阀 Flange Ball Valves 法兰球阀Flange Gate Valves 法兰闸阀Flange Globe Valves 法兰截止阀Gauge Valves 仪表阀Hand-operated valves 手动阀Hard Seal Butterfly Valves 金属密封碟阀 High Temperature Pressure Power Station Gate Valves 高温高压电站闸阀High Temperature Pressure Power Station Globe Valves 高温高压电站截止阀 Hydraulic relay valves 液压继动阀Lift Check Valves 升降式止回阀Lift Check Valves 升降式止回阀Limit valves 限位阀Lining Ball Valves 衬里球阀Lining Butterfly Valves 衬里碟阀Lining Check Valves 衬里止回阀Lining Cock 衬里二通Lining Globe Valves 衬里截止阀Lining T-Cock Valves 衬里三通旋塞阀 Liquid Indicator 液位计LPG Pipe Fitting 液化气管件Magnetic Co-operate Globe Valves磁耦合截止阀Magnetism Forle Pumps 磁力泵Manual Oil Pumps Valves 手摇油泵(阀) Meter Needle Type Globe Valves 仪表针形截止阀Oblique Stop Valves 直流式截止阀 Parallel Slide Valves 浆液阀Pintle valve 针形阀Piping Centrifugal Pumps 管道离心泵 Plunger valves 柱塞阀Pressure valve 压力（増压）阀Piping Pumps 管道泵Piping Safety Valves 管道安全阀Plunger Globe Valves 柱塞截止阀Quick Draining Valves 快速排污阀 Restrictor Valves 过流阀(或节流阀) Safety Valves 安全阀Screw Pumps 螺杆泵 Scum Gate Valves 排渣闸阀Air valves 空气阀门 Angle Stop valves 角式截止阀Angle Throttle Valves 角式节流阀 Angle Type Globe Valves 门角式截止阀Ash valves 排灰阀 Aspirating valves 吸（抽）气阀Auxiliary valves 辅助（副）阀 Balance valves 平衡阀Bellows valves 波纹管阀 Blowdown valves 泄料（放空，排污）阀Brake valves 制动阀 Butterfly Type Non-slam Check 蝶式缓冲止回阀Butterfly Valves with Gear Actuator 蜗轮传动蝶阀 Buttwelding valves 对焊连接阀Clamp valves 对夹式阀门 Cock 二通Combination valves 组合阀 CQ Thread Ball Valves CQ螺纹球阀Culvert valves 地下管道阀 Deceleration valves 减速阀Diaphragm Valves 隔膜阀 Decompression valves 泄压阀Double Disc Flat Gate Valves 双闸板平板闸阀 Double Disk Parallel Gate Valves明杆平行式双闸板闸板 Double Opening Exhaust Valves 双口排气球 Drainage valves 排水阀Electric Actuated Stop Valves 电动截止阀 Electric Actuated Wedge Gate Valves电动楔式闸阀Electric Double Disk Parallel Gate Valves电动平行式双闸板闸板 Emergeny Cut-off Valves 紧急切断阀Exhaust valves 排气阀 Free Float Type Steam Trap 浮球式疏水阀Flange Ball Valves 法兰球阀 Flange Gate Valves 法兰闸阀Flange Globe Valves 法兰截止阀 Gauge Valves 仪表阀Hand-operated valves 手动阀 Hard Seal Butterfly Valves 金属密封碟阀High Temperature Pressure Power Station Gate Valves 高温高压电站闸阀High Temperature Pressure Power Station Globe Valves 高温高压电站截止阀Hydraulic relay valves 液压继动阀 Lift Check Valves 升降式止回阀Lift Check Valves 升降式止回阀 Limit valves 限位阀Lining Ball Valves 衬里球阀 Lining Butterfly Valves 衬里碟阀Lining Check Valves 衬里止回阀 Lining Cock 衬里二通Lining Globe Valves 衬里截止阀 Lining T-Cock Valves 衬里三通旋塞阀Liquid Indicator 液位计 LPG Pipe Fitting 液化气管件Magnetic Co-operate Globe Valves磁耦合截止阀 Magnetism Forle Pumps 磁力泵Manual Oil Pumps Valves 手摇油泵(阀) Meter Needle Type Globe Valves 仪表针形截止阀 Oblique Stop Valves 直流式截止阀 Parallel Slide Valves 浆液阀Pintle valve 针形阀 Piping Centrifugal Pumps 管道离心泵Plunger valves 柱塞阀 Pressure valve 压力（増压）阀Piping Pumps 管道泵 Piping Safety Valves 管道安全阀Plunger Globe Valves 柱塞截止阀 Quick Draining Valves 快速排污阀Restrictor Valves 过流阀(或节流阀) Safety Valves 安全阀Screw Pumps 螺杆泵 Scum Gate Valves 排渣闸阀Solenoid valves 电磁阀 Single Disc Flat Gate Valves 单闸板平板闸阀 Single Opening Exhaust Valves 单口排气球 Slurry Pumps 泥浆泵Stop Valves 截止阀 Strainer 过滤器 Submerged Motor Pumps 潜水电泵(排污泵)Swing Check Valves 旋启式止回阀 Swing Check Valves 旋启式止回阀Tank Lorry Ball Valves 槽车球阀 T-Cock 三通Thin Gate Valves 薄型闸阀 Throttle Valves 节流阀Tiny Drag Slow Shut Check Valves 微阻缓闭止回阀 Triple (tee) valves 三通阀Two-way valves 二通阀 Under Water Pumps 液下泵Vacuum Pumps 水力喷射器(真空泵) Vertical Lift Check Valves 立式止回阀Wafer Check Valves 对夹式止回阀 Wafer plate valves 对夹蝶板阀Wafer Type Butterfly Valves with Rubber Itning对夹式衬胶蝶阀 Waste Valves 排污箱(阀)Water Seal Gate Valves 水封闸阀 Wedge Gate Valves 楔式闸阀Y Type and Cylinder Filters Y型筒型过滤器阀门零部件英汉术语对照Axis Guide 轴套 Ball 球、球芯Ball seat 密封圈 Blowdown Sealing Face 启、阀件密封面Body 阀体 Bonnet 阀盖Disc 阀瓣 Mut 螺母Screw 螺栓 Sealing 密封件Spring 弹簧 Stem 阀杆Stem Mut 阀杆螺母 Stem seal 填料Wedge Disc 闸板阀门规范技术英语术语对照Applicable medium 适用介质 Applicable temperature 适用温度Butt Clamp 对夹 Chemical analysis 化学成份Connecting format 连接形式 Double disc 双闸板Flexible disc 弹性闸板 Flange 法兰 Hoop 卡箍Inside thread 内螺纹 Jacket 夹套Mains 电源 Material chemical analysis and mechanical capacity材料化学成份和机械性能 materials 材料 Materials for main parts 主要零件材料 Mechanical capacity 机械性能Max. Discharging Capacity 最大排水量 Max. Operating Temperature 最高工作温度Max. Allowable Temperature 最高允许温度 Max. Allowable Pressure 最高允许压力Model 型号 N ame of parts 零件名称nitrogen (N) 氮 Nominal bore 公称通径Nominal Pressure 公称压力 Nozzle 排气口Outside thread 外螺纹 Oxidant 氧化性介质Parallel 平行 Piping 管路Piston 活塞 Reductant 还原性介质Rising stem 明杆 Seal 阀座，密封面Seat testing pressure 压力气密封试验压力 Socket 卡套Specifications 性能规范 Single disc 单闸板Solid 刚性 Strengh testing pressure 强度试验压力Steam , condensate 蒸汽,凝结水 Stroke 冲程，行程Water,oil,steam 水,温度,气 Wedge 楔式 Welding 焊接阀门材质术语英汉对照Atbas metal 镍铬钢 Buna-N rubber 丁晴橡胶Casting aluminium brass 铸铝黄铜 Casting aluminium bronze 铸铝青铜Ceramic metal 陶瓷金属 Chromel alloy 镍铬合金CHR rubber 氯晴橡胶 Chrominm-molybdenum-vanadium steel 铬钼钒钢 Chromium stainless steel 铬不锈钢 Chromium-molybdenum steel 铬钼钢Corrugation pad 波形垫 Cuprum alloy 铜合金Ductile Cast iron 球墨铸铁 Expanded graphite 柔性石墨Fine Steel Casting iron 优质碳素钢 Fluorous rubber 氟橡胶Gray Cast iron 灰铸铁 Haynes alloy 钴铬钨合金High tem perature steel 高温钢 Monel 蒙乃尔合金Low temperature steel 低温钢 Nylon 尼龙塑料Polytetrafluoroethylene(PTEF) 聚四氟乙烯 Polythene 聚乙烯Pure aluminium 纯铝 Pure cupper 纯铜Rubber graphite board 橡胶石墨板 Spring steel 弹簧钢Stainless acid-resisting steel 不锈耐酸钢 Stainless and Graphite 不锈钢/石墨Stainless steel 不锈钢 Steel Casting iron 碳素钢铸件Shell Test Pressure 壳体试验压力 Service Fluid 工作介质。
完整版阀门专业术语中英文对照
完整版阀门专业术语中英文对照1. 缩写词和代号1.1 法兰结构形式及密封面代号BL---Blind Flange 法兰盖 LF/SE---Lapped Joint Flange SO---Slip-On Welding Flange SW---Socket Welding FlangeTh---Thread Flange 螺纹法兰 FF---All Flat Face 全平面RF---Raised Face 突面 FM---Female Face 凹面M---Male Face 凸面T---Tongue Face榫面 G---Groove Face槽面 RJ---Ring Joint 环连接面 1.2常用缩写词'13Cr + STL---13Cr Trim with Stellited Seat DWD---Split Wedge Disc 楔形双闸板MFR'S---Manufacturer's Standard 制造厂标准RWD---Resilient Wedge Disc13Cr 阀芯带 STL 阀座 "ENP---Electroless Nickel Plating 镍磷硼合金镀层NBR---Nitrile-butadiene Ruber丁腈橡胶 Sch.No.---Schedule Number管表号 Bana-N 丁钠橡胶FE---Flanged End 法兰连接端NPS---Nominal Pipe Size 管子公称尺寸（英制）STL---Stellited 硬质合金（钴－铬－钨合金） BB---Bolted Bonnet 螺栓连接的阀盖FLG---Flange 法兰NPT---National Pipe Taper Thread 60SWD---Solid Wedge Disc 楔形单闸板 BC---Bolted Cap 螺栓连接的阀帽 FS---Forged Steel 锻钢NRS---Non-Rising Stem 暗杆 SW Socket Weld 承插焊BN---Bayonet 卡套连接FWD---Flexible Wedge Disc挠性楔形闸板 OS---Outside Screw 外螺纹TB---Thread Bonnet 螺纹阀盖BRZ---Bronze 青铜GALV---Galvanized 镀锌OS&Y---Outside Screw with Yoke 外螺纹带支架WN---Welding Neck Flange带颈对焊法兰对焊环松套法兰带颈平焊兰承插焊法兰弹性闸板锥管螺纹TE---Thread End 螺纹端BW---Butt Weld 对焊连接HEX—六角头(螺栓)PTFE---Polytetrafluoroethylene 聚四氟乙烯TC---Thread Cap 螺纹阀帽CI---Cast Iron 铸铁HF---Hard Face 硬表面RTFE---Reinforced PTFE 增强PTFEWB---Welded Bonnet 焊接阀盖CS---Carbon Steel 碳钢HW---Handlewheel 手轮缩写说明BE 坡口BW 对焊BL 法兰盖BC.SWING 螺栓阀盖旋启式BB.OS&Y 螺栓阀盖外螺纹及轭式BC.LIFT 螺栓阀盖升降式Dual-plate 双蝶板FB.L.OP. 全通径手工操作FB.GEAR OP. 全通径齿轮操作FF 全平面FL 法兰F 锻件GV 镀锌HF 硬质合金堆焊LJ 活套法兰L 翻边短节短规格LL 翻边短节长规格MFR'S.ST'd 制造商标准NPT 螺纹(60O)PE 平口PTFE 聚四氟乙烯RPTFE 增强聚四氟乙烯RF 突面STR 过滤器SM 无缝STL 硬质合金SW 承插SO 平焊Sch 管道壁厚标号SB.ISRS 螺纹阀盖内螺纹明杆ISNS 内螺纹暗杆WL 焊接WN 带颈对焊WFR 对夹Y2 半硬不锈钢焊管专业名称中英文对照（一）锅炉热交换器用不锈钢钢管：stainless steel tube for boiler ，heat— excha nger材质：grade 外径：OD焊接方式：welding method包装方式：packing 标准：standard 壁厚：wt 产品应用：application 捆包木箱包装：bundle or wooden case 规格：specification薄壁不锈钢水管：light gauge stainless steel water pipes 食品卫生不锈钢管：stainless steel sanitary tubes 开卷uncoiling 活塞loop 成型forming 焊接welding内外焊缝整平outside inside weld bead rolling 预矫正precalibration感应热处理：induction heat treating 定径矫直sizing straightening 涡流检测eddy current test喷码marking 切断cutting 水压检查hydrostatic test水下气压测试under water air pressure testX 射线检查X ray inspection 酸洗pickling 最终检查final inspection 发运shipping 光亮退火bright annealing 尺寸检测dimention examination 表面质量surface examination 液压试验hydrostatic test 气压测试pneumatic test 硬度测试harness test 金相组织测试分析metallographic examination 晶间腐蚀测试intergranular corrosion test机械性能测试mechanical property test 拉伸试验tension test 压扁试验flattering testASTM 标准下不锈钢焊管A249 关于奥氏体广泛用于热交换器，锅炉，过热器，冷凝器的焊管A269 一般用途用无缝和焊接的奥氏体不锈钢管制品标准A270 奥氏体铁素体无缝管卫生管A554 机械用焊管ASTM 命名方法及扩充（以ASTM A249 为例）:其中在ASTM 标准下，分别有以A.B.C 为首字母A：ferrous material 亚铁含铁材料黑色金属材料B：non —ferrous materials 不含铁材料有色金属材料C: cementitious materials 胶结材料ASTM A249 在A248 出版之后发展，分配可以用数字，在A25.0 出现之前没有实际意义。
阀门术语中英文对照
容积式压缩机positive displacement compressor往复式压缩机（活塞式压缩机）reciprocating compressor回转式压缩机rotary compressor滑片式压缩机sliding vane compressor单滑片回转式压缩机single vane rotary compressor滚动转子式压缩机rolling rotor compressor三角转子式压缩机triangle rotor compressor多滑片回转式压缩机multi-vane rotary compressor滑片blade旋转活塞式压缩机rolling piston compressor涡旋式压缩机scroll compressor涡旋盘scroll固定涡旋盘stationary scroll, fixed scroll驱动涡旋盘driven scroll, orbiting scroll斜盘式压缩机（摇盘式压缩机）swash plate compressor斜盘swash plate摇盘wobble plate螺杆式压缩机screw compressor单螺杆压缩机single screw compressor阴转子female rotor阳转子male rotor主转子main rotor闸转子gate rotor无油压缩机oil free compressor膜式压缩机diaphragm compressor活塞式压缩机reciprocating compressor单作用压缩机single acting compressor双作用压缩机double acting compressor双效压缩机dual effect compressor双缸压缩机twin cylinder compressor闭式曲轴箱压缩机closed crankcase compressor开式曲轴箱压缩机open crankcase compressor顺流式压缩机uniflow compressor逆流式压缩机return flow compressor干活塞式压缩机dry piston compressor双级压缩机compound compressor多级压缩机multistage compressor差动活塞式压缩机stepped piston compound compressor, differential piston compressor 串轴式压缩机tandem compressor, dual compressor截止阀line valve, stop valve排气截止阀discharge line valve吸气截止阀suction line valve部分负荷旁通口partial duty port能量调节器energy regulator容量控制滑阀capacity control slide valve容量控制器capacity control消声器muffler联轴节coupling曲轴箱crankcase曲轴箱加热器crankcase heater轴封crankcase seal, shaft seal填料盒stuffing box轴封填料shaft packing机械密封mechanical seal波纹管密封bellows seal转动密封rotary seal迷宫密封labyrinth seal轴承bearing滑动轴承sleeve bearing偏心环eccentric strap滚珠轴承ball bearing滚柱轴承roller bearing滚针轴承needle bearing止推轴承thrust bearing外轴承pedestal bearing臼形轴承footstep bearing轴承箱bearing housing止推盘thrust collar偏心销eccentric pin曲轴平衡块crankshaft counterweight, crankshaft balance weight 曲柄轴crankshaft偏心轴eccentric type crankshaft曲拐轴crank throw type crankshaft连杆connecting rod连杆大头crank pin end连杆小头piston pin end曲轴crankshaft主轴颈main journal曲柄crank arm, crank shaft曲柄销crank pin曲拐crank throw曲拐机构crank-toggle阀盘valve disc阀杆valve stem阀座valve seat阀板valve plate阀盖valve cage阀罩valve cover阀升程限制器valve lift guard阀升程valve lift阀孔valve port吸气口suction inlet压缩机气阀compressor valve吸气阀suction valve排气阀delivery valve圆盘阀disc valve环片阀ring plate valve簧片阀reed valve舌状阀cantilever valve条状阀beam valve提升阀poppet valve菌状阀mushroom valve杯状阀tulip valve缸径cylinder bore余隙容积clearance volume附加余隙（补充余隙）clearance pocket活塞排量swept volume, piston displacement理论排量theoretical displacement实际排量actual displacement实际输气量actual displacement, actual output of gas 气缸工作容积working volume of the cylinder活塞行程容积piston displacement气缸cylinder气缸体cylinder block气缸壁cylinder wall水冷套water cooled jacket气缸盖（气缸头）cylinder head安全盖（假盖）safety head假盖false head活塞环piston ring气环sealing ring刮油环scraper ring油环scrape ring活塞销piston pin活塞piston活塞行程piston stroke吸气行程suction stroke膨胀行程expansion stroke压缩行程compression stroke排气行程discharge stroke升压压缩机booster compressor立式压缩机vertical compressor卧式压缩机horizontal compressor角度式压缩机angular type compressor对称平衡型压缩机symmetrically balanced type compressor CQ螺纹球阀CQ Thread Ball ValvesL形三通式L-pattern three wayT形三通式T-pattern three way安全阀Safety valve暗杆闸阀Inside screw nonrising stem type gate valve百叶窗;闸板shutter百叶窗式挡板louver damper摆阀式活塞泵swing gate piston pump保温式Steam jacket type报警阀alarm valve报警阀;信号阀;脉冲阀sentinel valve背压调节阀back pressure regulating valve背压率Rate of back pressuec本体阀杆密封body stem seal波纹管阀Bellows valves波纹管密封阀bellow sealed valve波纹管密封式Bellows seal type波纹管平衡式安全阀Bellows seal balance safety valve波纹管式减压阀Bellows reducing valve波纹管式减压阀Bellows weal reducing valve薄膜thin film薄膜;隔膜diaphragm薄膜式减压阀Diapjragm reducing valve薄型闸阀Thin Gate Valves不封闭式Unseal type槽车球阀Tank Lorry Ball Valves颤振Flutter常闭式Normally closed type常开式Normally open type超低温阀门Cryogenic valve超高压阀门Super high pressure valve超过压力Overpressure of a safety valve衬胶隔膜阀rubber lined diaphragm衬胶截止阀rubber lined globe valve垂直板式蝶阀Vertical disc type butterfly valve磁耦合截止阀Magnetic Co-operate Globe Valves带补充载荷的安全阀Supplementary loaded safety valve带辅助装置的安全阀Assisted safety valve单阀碟双面平行密封闸阀parallel single disk gate valve单口排气阀Single Opening Exhaust Valves单向阀Non-return Valve单闸板Single gate disc单闸板平板闸阀Single Disc Flat Gate Valves弹簧薄膜式减压阀Spring diaphragm reducing valve弹簧式安全阀Direct spring loaded safety valve弹簧座Spring plate弹性闸板Flexible gate disc当量计算排量Equivalent calculated capacity挡板damper导阀Pilot valve导向套Valve guide disc guide低温阀门Sub-zero valve低压阀门Low pressure valve底阀bottom valve底阀Foot valve电磁动装置Eletro magnetic actuator电磁阀magnetic valve电磁阀solenoid valve电磁－液动装置Eletro magnetichydraulic actuator电动阀mortor operated valve电动阀motorized valve电动截止阀Electric Actuated Stop Valves电动平行式双闸板闸板Electric Double Disk Parallel Gate Valves 电动楔式闸阀Electric Actuated Wedge Gate Valves电动装置Electric actuator电－液动装置Eletro hydraulic actuator电液伺服阀electro-hydraulic servovalve调节弹簧Regulation spring调节阀adjusting valve调节阀control valve调节阀regulating valve调节螺套Adjusting bolt Adjusting screw调节圈Adjusting ring蝶板Disc蝶阀；瓣阀butterfly valve蝶阀；瓣阀；拍门；铰链阀flap valve蝶式缓冲止回阀Butterfly Type Non-slam Check蝶式止回阀Butterfly swing check valve定比减压阀Proprutioning pressure reducing valve定差减压阀Fixed differential reducing valve定值减压阀Fixed pressure reducing valve动态特性Dynamic characteristics对焊连接阀Buttwelding valves对夹蝶板阀Wafer plate valves对夹式衬胶蝶阀Wafer Type Butterfly Valves with Rubber Itning对夹式阀门Clamp valves对夹式止回阀Wafer Check Valves额定排量Certified capacity额定排量系数Derated coefficient of discharge 二通阀Two-way valves阀valve阀板valve deck plate阀板valve plate阀板式活塞泵valve deck plate type piston pump 阀板式活塞泵valve plate type piston pump阀瓣Disc阀操纵杆valve operating rod阀痤槽valve seat recess阀挡valve grid阀挡valve positioner阀挡valve stop阀导杆valve tail rod阀导向器valve guide阀盖bonnet阀盖衬套bonnet bush阀盖垫片bonnet gasket阀杆stem阀杆valve rod阀杆valve spindle阀杆端部尺寸Dimmension of valve stem end阀杆环stem ring阀杆螺母Yoke bushing Yoke nut阀杆填料stem packing阀杆头部尺寸Dimension of valve stem head阀簧valve spring阀簧压板valve spring plate阀控水锤泵valve-controlled hydraulic ram阀框架valve yoke阀门Valve阀门传动装置valve bandle set阀门和管件Valves and Fittings阀门盘根valve packing阀门手柄valve handle阀盘disc阀盘valve disc阀片Disc阀球valve ball阀驱动臂valve driving arm阀驱动臂valve motion arm阀式活塞valve type piston阀式活塞valve type bucket阀室式活塞泵valve box type piston pump阀室式活塞泵（美）valve pot type piston pump阀抬起装置valve lifting device阀体body阀体valve body阀箱valve box阀箱valve cage阀箱valve chest阀箱；阀限位器valve guard阀箱盖cover for valve box阀箱盖valve box cover阀箱式活塞泵（美）turret type piston pump阀形活塞泵valve type piston pump阀座Seat ring阀座valve carrier阀座valve seat(body seat)阀座；阀盘valve seat阀座环seat ring阀座密封嵌条sealing strip for valve seat法兰flange法兰堵头blind flange法兰端flange end法兰接头flange joint法兰连接紧固件（双头螺栓和螺帽）flange bolting 法兰密封面，法兰面flange facing法兰面加工flange facing finish法兰球阀Flange Ball Valves翻板阀Flap反冲盘Disc holder反向作用式减压阀Reverse acting reducing valve反向作用式减压阀Reverse acting reducing valve放空阀emptying valve放气阀air vent valve;vent valve放气阀；排气阀air evacuation valve放泄阀escape valve分置阀室式活塞泵separate valve box type piston pump 分置阀室式活塞泵（美）side pot type piston pump封闭式Seal type浮动式球阀Float ball valve浮球Ball float浮球阀Float Valve阀门种类中英文对照中文英文中文英文阀门valve 通用阀门General valve球阀Ball valve 槽车球阀Tank Lorry Ball ValvesCQ 螺纹球阀CQ Thread Ball Valves 法兰球阀Flange Ball Valves衬里球阀Lining Ball Valves API球阀API Ball valves浮动球阀Float Ball valves 固定球阀Trunnion-mounted Ball valves三通法兰球阀Three Ball valves V 型调节球阀V-Regulating Ball valves闸阀Gate valve 楔式闸阀Wedge Gate Valves法兰闸阀Flange Gate Valves 排渣闸阀Scum Gate V alves薄型闸阀Thin Gate Valves 水封闸阀Water Seal Gate Valves电动楔式闸阀Electric Actuated Wedge Gate Valves 平板闸阀Flat Gate Valve单闸板平板闸阀Single Disc Flat Gate Valves 电动平行式双闸板闸阀Electric Double Disk Parallel Gate Valves双闸板平板闸阀Double Disc Flat Gate Valves 明杆平行式双闸板闸阀Double Disk Parallel Gate Valves截止阀Globe valve 角式截止阀Angle Globe valves门角式截止阀Angle Type Globe V alves 电动截止阀Electric Actuated Stop V alves法兰截止阀Flange Globe Valves 衬里截止阀Lining Globe V alves直流式截止阀Oblique Stop Valves 柱塞截止阀Plunger Globe Valves止回阀Check valve 旋启式止回阀Swing Check Valves对夹式止回阀Wafer Check Valves 蝶式缓冲止回阀Butterfly Type Non-slam Check蝶式缓冲止回阀Butterfly Type Non-slam Check 升降式止回阀Lift Check Valves衬里止回阀Lining Check Valves 微阻缓闭止回阀Tiny Drag Slow Shut Check V alves立式止回阀Vertical Lift Check Valves蝶阀Butterfly Valve 对夹蝶板阀Wafer plate valve衬里蝶阀Lining Butterfly Valves 蜗轮传动蝶阀Butterfly Valves with Gear Actuator对夹式衬胶蝶阀Wafer Type Butterfly Valves with Rubber Itning 金属密封蝶阀Hard Seal Butterfly Valves隔膜阀diaphragm valve 旋塞阀plug valve安全阀safety valve 管道安全阀Piping Safety Valves回转阀rotary valve 减压阀pressure reducing valve减速阀Deceleration valves 泄压阀Decompression valves蒸汽疏水阀Automatic steam trap valve 组合阀Combination valves针形阀Pintle valve 仪表阀Gauge Valves仪表针形截止阀Meter Needle Type Globe Valves 空气阀门Air valves排灰阀Ash valves 吸（抽）气阀Aspirating valves辅助（副）阀Auxiliary valves 平衡阀Balance valves波纹管阀Bellows valves 泄料（放空，排污）阀Blowdown valves制动阀Brake valves 对焊连接阀Buttwelding valves地下管道阀Culvert valves 双口排气球Double Opening Exhaust Valves排水阀Drainage valves 紧急切断阀Emergeny Cut-off Valves排气阀Exhaust valves 浮球式疏水阀Free Float Type Steam Trap手动阀Hand-operated valves 液压继动阀Hydraulic relay valves限位阀Limit valves 衬里三通旋塞阀Lining T-Cock Valves 液位计Liquid Indicator 浆液阀Parallel Slide Valves柱塞阀Plunger valves 压力（増压）阀Pressure valve快速排污阀Quick Draining Valves 电磁阀Solenoid valves 过滤器Strainer 节流阀Throttle Valves阀门术语中英文对照中文英文口径bore公称通径Nominal diameter公称压力Nominal pressure工作温度Operating temperature工作压差Operating pressure工作背压Operating back pressure关闭压力Lockup pressure开启高度Lift壳体试验Shell test壳体试验压力Seal test pressure连接尺寸Conncetion cimension连接形式Type of connection流道面积Flow area流道直径Flow diameter流量孔板flow orifice plate流量特性Flow characteristics流量特性偏差Flow characteristics derivation漏汽量Steam loss密封面Sealing face密封试验Seal test密封试验压力Seal test pressure上密封Back seat上密封试验Back seal test适用介质Suitable medium适用温度Suitable temperature最大过冷度Maximum subcoold temperature最大流量Maximum flow rate最大压差Maximum differential pressure最低工作压力Minimum operating pressure最高背压率Maximum rate of back pressure最高允许压力Maximum allowable pressure最小过冷度Minimum subcooled temperature最小压差Minimum differntial pressure常闭式Normally closed type常开式Normally open type阀门零配件中英文对照中文英文阀体body阀盖bonnet阀盖垫片bonnet gasket阀盖衬套bonnet bush阀瓣Disc阀箱valve box阀座Seat ring阀杆Stem阀杆螺母Yoke bushing Yoke nut 法兰flange填料Packing填料垫Packing seat密封件Sealing挡板damper导向套Valve guide disc guide弹簧座Spring plate轴套Axis Guide球、球芯Ball密封圈Ball seat螺母Mut螺栓Screw弹簧Spring闸板Wedge Disc。
阀门英语术语对照
阀门英语术语对照 Document number：WTWYT-WYWY-BTGTT-YTTYU-2018GT第二节阀门术语一、阀门类别（中英文对照）闸阀[Gatevalve;Slidevalve]截止阀[Globevalve;Stopvalve]止回阀[Checkvalve;Non-returnvalve]球阀[Ballvalve]蝶阀[Butterflyvalve]旋塞阀[Plugvalve]节流阀[Throttlevalve]隔膜阀[Diaphragmvalve]针型阀[Pintlemvalve]低温阀[Lowtemperaturevalve]二、结构及零件(中英文对照）结构长度[FacetoFace;EndtoEnd;FacetoEnddimension] 结构形式[Typeofconstruction]角式[Angletype]直通式[Throughwaytype]保温式[Steamjackettype]连接形式[Typeofconnecting]电动装置[Electricactuator]气动装置[Pneumaticactuator]齿轮操作[Gearoperation]手轮操作[Handwheel]阀体[Body]阀盖[Bonnet;cover;cap;lid]阀瓣[Disc]闸板[Wedge]阀杆[Stem;Spindle]阀杆螺母[Stemnut;Yokenut]填料函[Stuffingbox]填料压盖[Gland]支架[Yoke]上密封[Backseat]阀座[Seat]螺栓[Blot]螺母[Nut]填料[Packing]球体[Ball]销轴[Hingepin]摇杆[Arm;Hinge]密封面[Sealface]主要性能参数[Specification]公称压力(PN)[Nominalpressure]公称通径（DN）[Nominaldiameter]工作压力[Workingpressure]壳体试验[Shelltest]密封试验[Sealtest]三、其它术语(中英文对照）BW表示对焊连接方式SW表示承插焊连接方式=全通径BB-螺栓连接阀盖PSB-内压自密封阀盖=齿轮操作BG-伞齿轮PWHT-焊后热处理PCD-中心圆直径=硬质面CS-碳钢FS-锻钢AS-合金钢SS-不锈钢CI-铸铁OS&Y-明杆支架结构。
阀门名词术语中英文对照
阀门名词术语中英文对照阀门valve闸阀 gate valve截止阀globe valve, stop valve节流阀throttle valve球阀ball valve蝶阀butterfly valve隔膜阀 diaphragm valve旋塞阀plug valve止回阀check valve, non-return valve安全阀safety valve, pressure减压阀pressure reducing valve疏水阀steam trap排污阀 blow-down valve调节阀(控制阀)control valve, adjusting valve 分配阀 dividing valve混合阀 mixing valve水力控制阀 hydraulic control valve手动阀门 manual operated valve电动阀门 electrical operated valve气动阀门 pneumatically operated valve 低压阀门 low pressure valve中压阀门 middle pressure valve高压阀门 high pressure valve超高压阀门 super high pressure valve 高温阀门 high temperature valve中温阀门 moderate temperature valve 常温阀门 normal temperature valve低温阀门 sub-zero valve超低温阀门 cryogenic valve结构长度 face-to-face dimension结构形式 type of construction直通式 through way type角式 angle type直流式 y-type三通式 three way typeT形三通式 T-pattern three wayL形三通式 L-pattern three way平衡式 balance type杠杆式 lever type常开式 normally open type 常闭式normally closed type保温式 steam jacket type波纹管式 bellows seal type全径阀门 full-port valve缩径阀门 reduced-port valve缩口阀门 reduced-bore valve单向阀门 unidirectional valve双向阀门 bidirectional valve上密封back seal压力密封pressure seal连接形式 type of connection壳体 shell阀体body阀盖bonnet启闭件disc阀座seat密封面 sealing face，surface阀杆 stem, spindle阀杆螺母yoke nut填料函（填料箱）stuffing box填料packing, packing rings填料垫packing seat, packing washer支架 yoke撞击手轮impact hand wheel阀瓣（阀芯） disc（valve core）楔式闸阀wedge gate valve闸板wedge单闸板single gate刚性闸版 rigid gate弹性闸板 flexible gate disc双闸板double gate楔式双闸板 wedge double gate平行式双闸板 parallel double gate浮动式球阀floating ball valve固定式球阀fixed ball valve球体 ball斜板式蝶阀inclined disc butterfly valve 蝶板 disc屋脊式隔膜阀weir diaphragm valve截止式隔膜阀 globe diaphragm valve隔膜diaphragm填料式旋塞阀 gland packing plug valve 油封式旋塞阀 lubricated plug valve塞子 plug升降式止回阀 lift check valve升降立式止回阀 vertical lift check valve 旋启式止回阀 swing check valve底阀 foot valve，bottom valve轴流式止回阀 axial flow check valve蝶式止回阀 butterfly swing check valve 销轴 hinge pin摇杆 arm先导式安全阀 pilot operated safety valve 全启式安全阀 full lift safety valve微启式安全阀 low lift safety valve双联弹簧式安全阀duplex safety valve真空安全阀vacuum relief valve敞开式安全阀openly sealed safety valve调节螺母adjusting screw弹簧座 spring plate导向套 dise guide反冲盘 disc holder调节圈 adjusting ring压力释放装置pressure relief device爆破片装置bursting disk device折断销装置breaking pin device弯折销装置buckling pin device剪切销装置shear pin device易熔塞装置fusible plug device排放面积discharge area流道面积flow area流道直径flow diameter帘面积curtain area开启高度lift额定开高rated lift密封面斜角seat angle密封面积seat area密封面平均直径seat mean diameter净流通面积net flow area喉径 throat diameter整定压力set pressure超过压力overpressure回座压力reseating pressure启闭压差blowdown排放压力 relieving pressure排放背压力 built-up back pressure附加背压力 superimposed back pressure理论排量 theoretical discharge capacity 额定排量 certified (discharge) capacity 频跳 chatter颤振 flutter封闭式 seal type非封闭式 unseal type在用试验in-service testing工作台上定压试验bench testing薄膜式减压阀 diaphragm reducing valve活塞式减压阀 piston reducing valve杠杆式减压阀 lever reducing valve膜片 diaphragm浮球式疏水阀 ball float steam trap浮桶式疏水阀 open bucket steam trap脉冲式疏水阀 impulse steam trap热动力式疏水阀 thermodynamic steam trap 蒸汽疏水阀 steam trap工作压力 operating pressure最高工作压力 maximum operating pressure 最低工作压力 minimum operating pressure 工作背压 operating back pressure背压率 rate of back pressure最大压差 maximum differential pressure最小压差 minimum differential pressure开阀温度 operating valve temperature关阀温度 closing valve temperature过冷度 subcooled temperature最小过冷度 minimum subcooled temperature 冷凝结水排量 cold condensate capacity热凝结水排量 hot condensate capacity漏汽量 steam loss无负荷漏汽量 unload steam loss 有负荷漏汽量 load steam loss无负荷漏汽率 rate of unload steam loss有负荷漏汽率 rate of load steam loss负荷率 rate of load condensate阀片 disc钟形罩 inverted bucket浮球 float ball浮桶 float bucket执行机构 actuator基本误差 intrinsic error回差 hysteresis error死区 dead band行程 travel额定行程 rated travel相对行程（h） relative travel（h）额定行程偏差 deviation of rated travel额定流量（Q） rated flow（Q）泄漏量 leakage流量系数 flow coefficient额定流量系数（K V）rated flow coefficient（K V）相对流量系数（Φ）relative flow coefficient（Φ）固有流量特性 inherent flow characteristic 可调比（R） inherent rangea bility（R）阻塞流 choked flow斜率偏差 slope deviation遥控浮球阀remote float control valve水利控制减压阀 pressure reducing valve缓闭止回阀 low speed closed check valve 持压/泄压阀 pressure sustaining ,relief valve 水泵控制阀 pump control valve最小开启压力 minimum open pressure驱动装置 actuator多回转驱动装置multi-turn actuator部分回转驱动装置part-turn actuator电动装置electric actuator气动装置pneumatic actuator直线型气动装置 linear pneumatic actuator回转型气动装置rotary pneumatic actuator气动装置的行程stroke of pneumatic actuator 液压驱动装置 hydraulic actuator电磁驱动装置 electro magnetic actuator 电-液联动装置electro hydraulic actuator气-液驱动装置pneumatic-hydraulic actuator 蜗轮传动装置 worm gear actuator正齿轮传动装置cylindrical gear actuator锥齿轮传动装置conical gear actuator转矩torque推力thrust壳体试验 shell test壳体试验压力 shll test pressure密封试验 seal test密封试验压力 seal test pressure上密封试验 back seal test静压寿命试验potential pressure life test耐火试验 fire test防静电试验 anti-static test主要性能参数specification公称压力nominal pressure公称尺寸nominal diameter工作压力 working pressure最高工作压力 maximum operating pressure工作温度 working temperature最高工作温度 maximum operating temperature 泄漏量 leakage吻合度 percent of contact area连接尺寸 connection dimension最大压差 maximum pressure differential 位置指示器 position indicator压力边界 pressure boundary。
阀门名词术语中英文对照
阀门名词术语中英文对照阀门valve闸阀 gate valve截止阀globe valve, stop valve节流阀throttle valve球阀ball valve蝶阀butterfly valve隔膜阀 diaphragm valve旋塞阀plug valve止回阀check valve, non-return valve安全阀safety valve, pressure减压阀pressure reducing valve疏水阀steam trap排污阀 blow-down valve调节阀(控制阀)control valve, adjusting valve 分配阀 dividing valve混合阀 mixing valve水力控制阀 hydraulic control valve手动阀门 manual operated valve电动阀门 electrical operated valve气动阀门 pneumatically operated valve 低压阀门 low pressure valve中压阀门 middle pressure valve高压阀门 high pressure valve超高压阀门 super high pressure valve 高温阀门 high temperature valve中温阀门 moderate temperature valve 常温阀门 normal temperature valve低温阀门 sub-zero valve超低温阀门 cryogenic valve结构长度 face-to-face dimension结构形式 type of construction直通式 through way type角式 angle type直流式 y-type三通式 three way typeT形三通式 T-pattern three wayL形三通式 L-pattern three way平衡式 balance type杠杆式 lever type常开式 normally open type 常闭式normally closed type保温式 steam jacket type波纹管式 bellows seal type全径阀门 full-port valve缩径阀门 reduced-port valve缩口阀门 reduced-bore valve单向阀门 unidirectional valve双向阀门 bidirectional valve上密封back seal压力密封pressure seal连接形式 type of connection壳体 shell阀体body阀盖bonnet启闭件disc阀座seat密封面 sealing face，surface阀杆 stem, spindle阀杆螺母yoke nut填料函（填料箱）stuffing box填料packing, packing rings填料垫packing seat, packing washer支架 yoke撞击手轮impact hand wheel阀瓣（阀芯） disc（valve core）楔式闸阀wedge gate valve闸板wedge单闸板single gate刚性闸版 rigid gate弹性闸板 flexible gate disc双闸板double gate楔式双闸板 wedge double gate平行式双闸板 parallel double gate浮动式球阀floating ball valve固定式球阀fixed ball valve球体 ball斜板式蝶阀inclined disc butterfly valve 蝶板 disc屋脊式隔膜阀weir diaphragm valve截止式隔膜阀 globe diaphragm valve隔膜diaphragm填料式旋塞阀 gland packing plug valve 油封式旋塞阀 lubricated plug valve塞子 plug升降式止回阀 lift check valve升降立式止回阀 vertical lift check valve 旋启式止回阀 swing check valve底阀 foot valve，bottom valve轴流式止回阀 axial flow check valve蝶式止回阀 butterfly swing check valve 销轴 hinge pin摇杆 arm先导式安全阀 pilot operated safety valve 全启式安全阀 full lift safety valve微启式安全阀 low lift safety valve双联弹簧式安全阀duplex safety valve真空安全阀vacuum relief valve敞开式安全阀openly sealed safety valve调节螺母adjusting screw弹簧座 spring plate导向套 dise guide反冲盘 disc holder调节圈 adjusting ring压力释放装置pressure relief device爆破片装置bursting disk device折断销装置breaking pin device弯折销装置buckling pin device剪切销装置shear pin device易熔塞装置fusible plug device排放面积discharge area流道面积flow area流道直径flow diameter帘面积curtain area开启高度lift额定开高rated lift密封面斜角seat angle密封面积seat area密封面平均直径seat mean diameter净流通面积net flow area喉径 throat diameter整定压力set pressure超过压力overpressure回座压力reseating pressure启闭压差blowdown排放压力 relieving pressure排放背压力 built-up back pressure附加背压力 superimposed back pressure理论排量 theoretical discharge capacity 额定排量 certified (discharge) capacity 频跳 chatter颤振 flutter封闭式 seal type非封闭式 unseal type在用试验in-service testing工作台上定压试验bench testing薄膜式减压阀 diaphragm reducing valve活塞式减压阀 piston reducing valve杠杆式减压阀 lever reducing valve膜片 diaphragm浮球式疏水阀 ball float steam trap浮桶式疏水阀 open bucket steam trap脉冲式疏水阀 impulse steam trap热动力式疏水阀 thermodynamic steam trap 蒸汽疏水阀 steam trap工作压力 operating pressure最高工作压力 maximum operating pressure 最低工作压力 minimum operating pressure 工作背压 operating back pressure背压率 rate of back pressure最大压差 maximum differential pressure最小压差 minimum differential pressure开阀温度 operating valve temperature关阀温度 closing valve temperature过冷度 subcooled temperature最小过冷度 minimum subcooled temperature 冷凝结水排量 cold condensate capacity热凝结水排量 hot condensate capacity漏汽量 steam loss无负荷漏汽量 unload steam loss 有负荷漏汽量 load steam loss无负荷漏汽率 rate of unload steam loss有负荷漏汽率 rate of load steam loss负荷率 rate of load condensate阀片 disc钟形罩 inverted bucket浮球 float ball浮桶 float bucket执行机构 actuator基本误差 intrinsic error回差 hysteresis error死区 dead band行程 travel额定行程 rated travel相对行程（h） relative travel（h）额定行程偏差 deviation of rated travel额定流量（Q） rated flow（Q）泄漏量 leakage流量系数 flow coefficient额定流量系数（K V）rated flow coefficient（K V）相对流量系数（Φ）relative flow coefficient（Φ）固有流量特性 inherent flow characteristic 可调比（R） inherent rangea bility（R）阻塞流 choked flow斜率偏差 slope deviation遥控浮球阀remote float control valve水利控制减压阀 pressure reducing valve缓闭止回阀 low speed closed check valve 持压/泄压阀 pressure sustaining ,relief valve 水泵控制阀 pump control valve最小开启压力 minimum open pressure驱动装置 actuator多回转驱动装置multi-turn actuator部分回转驱动装置part-turn actuator电动装置electric actuator气动装置pneumatic actuator直线型气动装置 linear pneumatic actuator回转型气动装置rotary pneumatic actuator气动装置的行程stroke of pneumatic actuator 液压驱动装置 hydraulic actuator电磁驱动装置 electro magnetic actuator 电-液联动装置electro hydraulic actuator气-液驱动装置pneumatic-hydraulic actuator 蜗轮传动装置 worm gear actuator正齿轮传动装置cylindrical gear actuator锥齿轮传动装置conical gear actuator转矩torque推力thrust壳体试验 shell test壳体试验压力 shll test pressure密封试验 seal test密封试验压力 seal test pressure上密封试验 back seal test静压寿命试验potential pressure life test耐火试验 fire test防静电试验 anti-static test主要性能参数specification公称压力nominal pressure公称尺寸nominal diameter工作压力 working pressure最高工作压力 maximum operating pressure工作温度 working temperature最高工作温度 maximum operating temperature 泄漏量 leakage吻合度 percent of contact area连接尺寸 connection dimension最大压差 maximum pressure differential 位置指示器 position indicator压力边界 pressure boundary。
阀门专业术语
阀门专业术语阀门大全（中英对照）air-compressor valve 空气压缩机阀门automatic cutout valve 自动切断阀门backlash valve 无游隙阀门High temperature valve 高温阀门hose valve 水带阀门pipe manifold valves 管道汇集器阀门pneumatic cylinder cock valve 风动汽缸排水阀阀门pneumatic positioner valve 气动阀门定位器pneumatic sander valve 风动撒砂器阀门quick opening valve 快开阀门quick-opening gate valve 速启阀门standby valve 应急阀门; 备用阀门two selenoid 双螺管阀门valve chest 阀门室valve clearance 阀门间隙；阀余隙valveman 阀门操作者wash-out valve 清洗阀门adjusting valve 调整阀, 调节阀admission valve 进气阀; 进浆阀air admission valve 进气阀air bleed(ing) valve 排气阀; 排气嘴air control valve 空调阀air cylinder valve 气筒阀air escape valve 泄气阀air inlet valve (=air intake valve) 进气阀; 进风阀air operated throttle motor 风动节流器, 风动节流阀马达air pilot valve 空气导向阀air pressure governor valve 风压调压阀air relay valve 空气中继阀air release valve (=air relief valve) 排气阀; 放空阀air reversing valve 空气换向阀air shut-off valve 空气关闭阀air signal reducing valve 空气信号减压阀air slide valve 空气分配阀air starting (control) valve 空气起动(控制)阀air straining check valve 空气滤尘止回阀air valve 空气阀air vent valve 气动调压阀, 排气阀air-actuated direction valve 气动控制换向阀air-compressor valve 空气压缩机阀门air-operated valve 气动换向阀air-vacuum proportional valve 空真比例阀air-vacuum two way valve 空真二位阀alarm valve 报警阀aligned grid valve 栅极中点校直的电子管阀Allan valve 阿伦滑阀altitude valve 【航空】高度阀(航空发动机汽化器的可调整阀) ammonia valve 【工】氨阀angle back-pressure valve 背压角阀angle globe valve 折角球形阀angle stop valve 弯形止阀, 折角止阀angle valve 角阀angle water valve 折角水阀annular ring valve 环形阀; 环状阀anti-g valve 【航空】防超重活门, 抗重力阀application pilot valve 作用导阀application valve 作用阀, 控制阀ashpan blower valve 灰盘吹风阀Askania valve 射流管阀atmos valve (=atmospheric valve) 大气阀, 空气阀; 放空阀autocontrol valve 自动控制阀automatic air valve 自动空气阀automatic brake valve 自动制动阀automatic control valve 自动控制阀automatic cutout valve 自动切断阀门automatic delivery control valve 自动输送控制阀automatic drain valve 自动排水阀automatic expansion valve (定压式)自动膨胀阀automatic gas sampling valve 自动气体进样阀automatic reducing valve 自动减压阀(高速制动机) automatic regulating valve 自动调节阀automatic spring loaded valve 自动弹簧阀automatic supplementary air valve 自动补充(空)气阀automatic unloading valve 自动卸载阀automatic valve 自动阀automatic water level valve 自动水准阀automatically operated valve 自动操作阀automatic-control servo valve 自动控制伺服阀auxiliary changeover valve 辅助切换阀auxiliary valve 辅助阀(暖汽调整阀用)back valve 回动阀, 止回阀, 逆止阀, 单向阀backflush valve 反冲阀backlash valve 无游隙阀门back-pressure valve 止回阀back-up valve 列车后端制动阀balance pressure reducing valve 平衡减压阀balance slide valve 平衡滑阀balance valve 平衡阀, 均压阀balanced distribution valve 平衡配气阀balanced safety valve 平衡式安全阀(可变动背压)ball check valve 止回球阀, 球形节流阀ball float valve 浮子阀, 浮球阀ball non-return valve 球形止回阀ball relief valve 球形安全阀ball safety valve 球形安全阀ball stop valve 球形止阀ball valve 球阀, 弹子阀ball-and-lever valve 杠杆球阀bell valve 钟形阀, 装料钟bellows valve 波纹管阀bellows-operated pilot valve 膜盒控制导阀, 膜盒导引阀bevel seat valve 斜座阀, 角阀biased valve 承载阀blast furnace gas valve 高炉煤气阀blast regulation valve 通风调节阀bleed valve 排出阀; 放泄阀bleeder valve 放液阀, 放水阀block valve 隔断阀blocking valve 闭塞阀blow valve 通风阀, 安全阀, 放空阀blow-down valve 排气阀blower drain valve 鼓风机放泄阀blower regulation valve 通风调节阀blower valve 鼓风机阀blow-off valve 排出[泄]阀, 放泄[空]阀, 喷放阀blowout valve 排气管, 排出阀boiler check valve 锅炉止回阀boiler feed valve 锅炉给水阀bonnet valve 帽状阀bottom drain valve 底部放泄阀bottom valve 底阀brake application magnet valve 电磁制动阀brake application valve 制动作用阀brake control valve 制动控制阀brake cylinder release valve 制动缸缓解阀, 制动缸放风阀brake metering valve 制动调节阀brake pipe compensating valve 制动管补偿阀brake release magnet valve 缓解电磁阀brake valve 制动阀brass valve 黄铜阀brass-fitted cast-iron valve 黄铜配制铸铁阀brass-trimmed valve 黄铜配制阀breather valve 通气阀, 呼吸阀breathing type safety valve 呼吸式安全阀(罐车)brine retaining valve 盐水箱保持阀bucket valve 活塞阀buffer change valve 缓变阀building block valve 积木式阀, 集成阀built-in check valve 内装式单向阀bullet valve 球阀buried valve with key 液下控制阀butterfly control valve 蝶形控制阀butterfly throttle valve 蝶形节流阀butterfly valve 蝶阀by-pass valve 旁通阀, 辅助阀, 回流阀by-path valve 旁通阀, 辅助阀, 回流阀caboose valve 守车阀cage type valve 笼形阀cam-operated valve 凸轮控制阀capless tyre valve 无帽胎阀car discharge valve 车辆放风阀car signal valve 车辆信号阀, 车辆放风阀cartridge inserted valve 筒式插装式阀, 插装阀cement valve 【机】水泥止回阀center valve 中心阀centre bypass valve 中间位置旁通的换向阀, M型机能换向阀centre spool valve 中心柱形阀centrifugal saw plate valve 离心机的圆盘保险(溢流)阀centrifugal type injection valve 离心式喷射阀change valve 活页阀;旋转阀, 转换阀;多向阀charge valve 充气阀, 加载阀, 加液阀charging check valve 充气止回阀charging valve 充气阀, 加载阀, 加液阀check valve 单向阀, 止回阀, 防逆阀;检验阀check-valve pump 止回阀配流泵chimney valve 烟道阀choker checkvalve 阻气单向阀cindervalve 卸灰阀Cineston controller brake valve 钦式控制制动联合阀(用于地下铁道) circulating-water valve 循环水阀circulation valve 环流阀clack valve 止回阀clapper valve 瓣阀clock valve 单向绞链阀closed center valve 中间位置封闭的阀(方向阀); 闭中心阀closed crossover valve 正遮盖的换向阀closed exhaust valve 密闭排气阀closed-type fuel valve 密闭形燃油阀closing valve 隔离阀, 节制阀, 隔断阀, 停汽阀clutch application valve 离合器作用阀clutch temperature adjusting valve 离合器温度调节阀coasting valve 滑行阀, 惯性运动阀coaxial valve 同轴管[阀]cold water stop valve 凉水止阀column shut-off valve 柱关闭阀column switching valve 柱转换阀column valve 柱阀combination sliding and rotary spool valve 又移动又旋转的圆柱滑阀combination valve 组合阀combined inlet-outlet valve 进出组合阀combined strainer and check valve 混合滤尘止回阀common slide valve 普通滑阀compensated flow control valve 带压力补偿的流量控制阀;调速阀compensated relief valve 平衡式溢流阀compensating air valve 补充空气阀, 补偿气阀, 平衡气阀compensating valve 补偿阀compensation valve 平衡阀, 补偿阀compression release valve 减压阀compression valve (减振器的)压缩行程阀concentric valve 同心阀condensate valve 凝结水阀condenser level control valve 凝汽器水位调节阀condenser relief valve 凝气器安全阀condenser valve 凝汽阀conductor‘s valve 车长阀, 紧急制动阀cone valve 锥形阀cone-way valve 单向阀conical seat valve 锥形座阀conical valve 锥形阀constant pressure expansion valve 恒压膨胀活门, 恒压膨胀阀constant pressure valve 恒压阀control air type reducing valve 控制空气型减压阀control air valve 控制空气阀control valve 控制阀, 调节阀;控制管, 调节管controllable check valve 可控单向[止回检验]阀controller pilot valve 控制器管制阀conversion valve 转换阀;转向阀Air valves空气阀门Angle Stop valves 角式截止阀Angle Throttle Valves 角式节流阀Angle Type Globe Valves门角式截止阀Ash valves 排灰阀Aspirating valves 吸（抽）气阀Auxiliary valves 辅助（副）阀Balance valves 平衡阀Bellows valves 波纹管阀Blowdown valves 泄料（放空，排污）阀Brake valves 制动阀Butterfly Type Non-slam Check蝶式缓冲止回阀Butterfly Valves with Gear Actuator蜗轮传动蝶阀Buttwelding valves 对焊连接阀Clamp valves 对夹式阀门Cock二通Combination valves 组合阀CQ Thread Ball ValvesCQ螺纹球阀Culvert valves 地下管道阀Deceleration valves 减速阀Diaphragm Valves隔膜阀Decompression valves 泄压阀Double Disc Flat Gate Valves双闸板平板闸阀Double Disk Parallel Gate Valves明杆平行式双闸板闸板Double Opening Exhaust Valves双口排气球Drainage valves 排水阀Electric Actuated Stop Valves电动截止阀Electric Actuated Wedge Gate Valves电动楔式闸阀Electric Double Disk Parallel Gate Valves电动平行式双闸板闸板Emergeny Cut-off Valves紧急切断阀Exhaust valves 排气阀Free Float Type Steam Trap浮球式疏水阀Flange Ball Valves法兰球阀Flange Gate Valves法兰闸阀Flange Globe Valves法兰截止阀Gauge Valves仪表阀Hand-operated valves 手动阀Hard Seal Butterfly Valves金属密封碟阀High Temperature Pressure Power Station Gate Valves 高温高压电站闸阀High Temperature Pressure Power Station Globe Valves 高温高压电站截止阀Hydraulic relay valves 液压继动阀Lift Check Valves升降式止回阀Lift Check Valves升降式止回阀Limit valves 限位阀Lining Ball Valves衬里球阀Lining Butterfly Valves衬里碟阀Lining Check Valves衬里止回阀Lining Cock衬里二通Lining Globe Valves衬里截止阀Lining T-Cock Valves衬里三通旋塞阀Liquid Indicator液位计LPG Pipe Fitting液化气管件Magnetic Co-operate Globe Valves 磁耦合截止阀Magnetism Forle Pumps磁力泵Manual Oil Pumps Valves手摇油泵(阀)Meter Needle Type Globe Valves 仪表针形截止阀Oblique Stop Valves直流式截止阀Parallel Slide Valves浆液阀Pintle valve 针形阀Piping Centrifugal Pumps管道离心泵Plunger valves 柱塞阀Pressure valve 压力（増压）阀Piping Pumps管道泵Piping Safety Valves管道安全阀Plunger Globe Valves柱塞截止阀Quick Draining Valves快速排污阀Restrictor Valves过流阀(或节流阀)Safety Valves安全阀Screw Pumps螺杆泵Scum Gate Valves排渣闸阀Solenoid valves 电磁阀Single Disc Flat Gate Valves单闸板平板闸阀Single Opening Exhaust Valves单口排气球Slurry Pumps泥浆泵Stop Valves截止阀Strainer过滤器Submerged Motor Pumps潜水电泵(排污泵)Swing Check Valves旋启式止回阀Swing Check Valves旋启式止回阀Tank Lorry Ball Valves槽车球阀T-Cock三通Thin Gate Valves薄型闸阀Throttle Valves节流阀Tiny Drag Slow Shut Check Valves微阻缓闭止回阀Triple (tee) valves 三通阀Two-way valves 二通阀Under Water Pumps液下泵Vacuum Pumps水力喷射器(真空泵)Vertical Lift Check Valves立式止回阀Wafer Check Valves对夹式止回阀Wafer plate valves 对夹蝶板阀Wafer Type Butterfly Valves with Rubber Itning 对夹式衬胶蝶阀Waste Valves排污箱(阀)Water Seal Gate Valves水封闸阀Wedge Gate Valves楔式闸阀Y Type and Cylinder Filters Y型筒型过滤器2.零部件术语Axis Guide轴套Ball球、球芯Ball seat密封圈Blowdown Sealing Face 启、阀件密封面Body阀体Bonnet阀盖Disc阀瓣Mut螺母Screw螺栓Sealing密封件Spring弹簧Stem阀杆Stem Mut阀杆螺母Stem seal填料Wedge Disc闸板3.规范技术术语Applicable medium适用介质Applicable temperature适用温度对夹Chemical analysis化学成份Connecting format连接形式Double disc双闸板Flexible disc弹性闸板Flange法兰Hoop卡箍Inside thread内螺纹Jacket 夹套Mains 电源Material chemical analysis and mechanical capacity 材料化学成份和机械性能materials材料Materials for main parts主要零件材料Mechanical capacity机械性能Max. Discharging Capacity最大排水量Max. Operating Temperature最高工作温度Max. Allowable Temperature最高允许温度Max. Allowable Pressure最高允许压力Model型号Name of parts零件名称nitrogen (N) 氮Nominal bore 公称通径Nominal Pressure公称压力Outside thread外螺纹Oxidant氧化性介质Parallel 平行Piping管路Piston 活塞Reductant还原性介质Rising stem明杆Seal 阀座，密封面Seat testing pressure压力气密封试验压力Socket卡套Specifications性能规范Single disc单闸板Solid刚性Strengh testing pressure 强度试验压力Steam , condensate蒸汽,凝结水Stroke 冲程，行程Water,oil,steam水,温度,气Wedge楔式Welding焊接4、材料术语Atbas metal镍铬钢Buna-N rubber 丁晴橡胶Casting aluminium brass 铸铝黄铜Casting aluminium bronzeCeramic metal 陶瓷金属Chromel alloy 镍铬合金CHR rubber氯晴橡胶Chrominm-molybdenum-vanadium steel 铬钼钒钢Chromium stainless steel铬不锈钢Chromium-molybdenum steel铬钼钢Corrugation pad波形垫Cuprum alloy铜合金Ductile Cast iron球墨铸铁Expanded graphite柔性石墨Fine Steel Casting iron优质碳素钢Fluorous rubber氟橡胶Gray Cast iron灰铸铁Hayne's alloy钴铬钨合金High tem perature steel高温钢Monel 蒙乃尔合金Low temperature steel低温钢Nylon尼龙塑料Polytetrafluoroethylene(PTEF)聚四氟乙烯Polythene 聚乙烯Pure aluminium纯铝Pure cupper纯铜Rubber graphite boardSpring steel弹簧钢Stainless acid-resisting steel不锈耐酸钢Stainless and Graphite不锈钢/石墨Stainless steel不锈钢Steel Casting iron碳素钢铸件Shell Test Pressure壳体试验压力Service Fluid工作介质阀门名称阀门名称CQ 螺纹球阀CQ Thread Ball ValvesL 形三通式L-pattern three wayT 形三通式T-pattern three way安全阀Safety valve暗杆闸阀Inside screw nonrising stem type gate valve 百叶窗; 闸板shutter百叶窗式挡板louver damper摆阀式活塞泵swing gate piston pump保温式Steam jacket type报警阀alarm valve报警阀; 信号阀; 脉冲阀sentinel valve背压调节阀back pressure regulating valve背压率Rate of back pressure本体阀杆密封body stem seal波纹管阀Bellows valves波纹管密封阀bellow sealed valve波纹管密封式Bellows seal type波纹管平衡式安全阀Bellows seal balance safety valve 波纹管式减压阀Bellows reducing valve波纹管式减压阀Bellows weal reducing valve薄膜thin film薄膜; 隔膜diaphragm薄膜式减压阀Diapjragm reducing valve薄型闸阀Thin Gate Valves不封闭式Unseal type槽车球阀Tank Lorry Ball Valves颤振Flutter常闭式Normally closed type常开式Normally open type超低温阀门Cryogenic valve超高压阀门Super high pressure valve超过压力Overpressure of a safety valve衬胶隔膜阀rubber lined diaphragm衬胶截止阀rubber lined globe valve垂直板式蝶阀Vertical disc type butterfly valve磁耦合截止阀Magnetic Co-operate Globe Valves带补充载荷的安全阀Supplementary loaded safety valve 带辅助装置的安全阀Assisted safety valve单阀碟双面平行密封闸阀parallel single disk gate valve 单口排气阀Single Opening Exhaust Valves单向阀Non-return Valve单闸板Single gate disc单闸板平板闸阀Single Disc Flat Gate Valves弹簧薄膜式减压阀Spring diaphragm reducing valve弹簧式安全阀Direct spring loaded safety valve弹簧座Spring plate弹性闸板Flexible gate disc当量计算排量Equivalent calculated capacity挡板damper导阀Pilot valve导向套Valve guide disc guide低温阀门Sub-zero valve低压阀门Low pressure valve底阀bottom valve底阀Foot valve电磁动装置Eletro magnetic actuator电磁阀magnetic valve电磁阀solenoid valve电磁－液动装置Eletro magnetichydraulic actuator电动阀mortor operated valve电动阀motorized valve电动截止阀Electric Actuated Stop Valves电动平行式双闸板闸板Electric Double Disk Parallel Gate Valves 电动楔式闸阀Electric Actuated Wedge Gate Valves电动装置Electric actuator电－液动装置Eletro hydraulic actuator电液伺服阀electro-hydraulic servovalve调节弹簧Regulation spring调节阀adjusting valve调节阀control valve调节阀regulating valve调节螺套Adjusting bolt Adjusting screw调节圈Adjusting ring蝶板Disc蝶阀；瓣阀butterfly valve蝶阀；瓣阀；拍门；铰链阀flap valve蝶式缓冲止回阀Butterfly Type Non-slam Check蝶式止回阀Butterfly swing check valve定比减压阀Proprutioning pressure reducing valve定差减压阀Fixed differential reducing valve定值减压阀Fixed pressure reducing valve动态特性Dynamic characteristics对焊连接阀Buttwelding valves对夹蝶板阀Wafer plate valves对夹式衬胶蝶阀Wafer Type Butterfly Valves with Rubber Itning对夹式阀门Clamp valves对夹式止回阀Wafer Check Valves额定排量Certified capacity额定排量系数Derated coefficient of discharge二通阀Two-way valves阀valve阀板valve deck plate阀板valve plate阀板式活塞泵valve deck plate type piston pump阀板式活塞泵valve plate type piston pump阀瓣Disc阀操纵杆valve operating rod阀痤槽valve seat recess阀挡valve grid阀挡valve positioner阀挡valve stop阀导杆valve tail rod阀导向器valve guide阀盖bonnet阀盖衬套bonnet bush阀盖垫片bonnet gasket阀杆stem阀杆valve rod阀杆valve spindle阀杆端部尺寸Dimmension of valve stem end阀杆环stem ring阀杆螺母Yoke bushing Yoke nut阀杆填料stem packing阀杆头部尺寸Dimension of valve stem head阀簧valve spring阀簧压板valve spring plate阀控水锤泵valve-controlled hydraulic ram阀框架valve yoke阀门Valve阀门传动装置valve bandle set阀门和管件Valves and Fittings阀门盘根valve packing阀门手柄valve handle阀盘disc阀盘valve disc阀片Disc阀球valve ball阀驱动臂valve driving arm阀驱动臂valve motion arm阀式活塞valve type piston阀式活塞valve type bucket阀室式活塞泵valve box type piston pump阀室式活塞泵（美）valve pot type piston pump 阀抬起装置valve lifting device阀体body阀体valve body阀箱valve box阀箱valve cage阀箱valve chest阀箱；阀限位器valve guard阀箱盖cover for valve box阀箱盖valve box cover阀箱式活塞泵（美）turret type piston pump阀形活塞泵valve type piston pump阀座Seat ring阀座valve carrier阀座valve seat(body seat)阀座；阀盘valve seat阀座环seat ring阀座密封嵌条sealing strip for valve seat法兰flange法兰堵头blind flange法兰端flange end法兰接头flange joint法兰连接紧固件（双头螺栓和螺帽）flange bolting 法兰密封面，法兰面flange facing法兰面加工flange facing finish法兰球阀Flange Ball Valves翻板阀Flap反冲盘Disc holder反向作用式减压阀Reverse acting reducing valve 反向作用式减压阀Reverse acting reducing valve 放空阀emptying valve放气阀air vent valve;vent valve放气阀；排气阀air evacuation valve放泄阀escape valve分置阀室式活塞泵separate valve box type piston pump 分置阀室式活塞泵（美）side pot type piston pump封闭式Seal type浮动式球阀Float ball valve浮球Ball float浮球阀Float Valve浮球式疏水阀Ball float steam trap浮球式疏水阀Free Float Type Steam Trap浮桶Bucket float浮桶式疏水阀Open bucket steam trap辅助（副）阀Auxiliary valves负荷率Rate of load condensate附加背压力Superimposed back pressure复位弹簧Returnning spring杠杆式Lever type杠杆式安全阀Lever and weight loaded safety valve杠杆式减压阀Lever reducing valve高温阀门High temperature valve高压阀门High pressure valve格兰密封gland隔离阀isolating valve隔膜Diaphragm隔膜阀diaphragm valve隔膜式控制阀diaphragm operated comtrol valve工作背压Operating back pressure工作温度Operating temperature工作温度Working temperature工作压差Operting differential pressure工作压力Operating pressure工作压力Working pressure公称通径Nominal diameter公称压力Nominal pressure固定式球阀Fixed ball valve关闭压力Lockup pressure关阀过冷度Subcooled temperature of close valve关阀温度Closing valve temperature管道安全阀Piping Safety Valves过冷度Subcoold temperature过流阀( 或节流阀) Restrictor Valves喉径Throat diameter滑阀slide valve滑阀式回转活塞泵rotary piston pump with slide gate 滑阀型转子泵eccentric rotary pump with sliding sleeve 环形阀annular valve环形阀double beat valve换向阀selector valve换向阀shuttle valve回转滑阀活塞泵piston pump with rotary gate回座压力Re-seating pressure of a safety valve活塞暱减压阀Piston reducing valve活塞式阀piston valve活塞式阀；柱塞式阀plunger valve活塞式减压阀Piston reducing valve减速阀Deceleration valves减压比Pressure reducing ratio减压阀pressure reducing valve浆液阀Parallel Slide Valves角阀Angle Valve角阀isolation valve angle configuration角式Angie type角式节流阀Angle Throttle Valves角式截止阀Angle Stop valves铰链阀；片状阀flapper valve节流阀throttle valve节流阀choke valve节流阀；节流throttle结构长度Face-to-face dimension End-to-end dimension Face-to-centre dimension 结构形式Type of construction截止阀Globe valve截止阀Shut-off Valve截止阀；关断阀shut-off valve截止式隔膜阀Globe diaphragm valve紧急切断阀Emergeny Cut-off Valves进气阀air intake valve进水阀；进口阀门inlet valve静态特性Static characteristics静态特性偏差Static characteristics derivation开阀过冷度Subcooled temperature of open valve开阀温度Opening valve temperature开启高度Lift壳体试验Shell test壳体试验压力Sheal test pressure空气阀门Air valves快速排污阀Quick Draining Valves类型Type冷凝结水排量Cold condensate capacity冷态试验差压力Cold differential test pressure理论排量Theoretical flowing capacity连接槽尺寸Dimension of connecting channel连接尺寸Connection dimension连接形式Type of connection帘面积Curtain area流道面积Flow area流道直径Flow diameter流量孔板flow orifice plate流量控制阀flow control valve流量特性Flow characteristics流量特性偏差Flow characteristics derivation漏汽量Steam loss脉冲式疏水阀Impulse steam trap密封面Sealing face密封试验Seal test密封试验压力Seal test pressure明杆平行式双闸板闸板Double Disk Parallel Gate Valves明杆闸阀Outside screw stem rising through handwheel type gate valve 膜片Diaphragm内压自封Pressure seat逆止阀；止回阀check valve逆止阀；止回阀non-return valve逆止阀; 止回阀; 单向阀check valve排放背压力Brilt-up back pressure排放压力Relieving pressure排灰阀Ash valves排量系数Coefficient of discharge排气阀air release valve排气阀Exhaust valves排气阀Vent Valve排水阀Drainage valves排水温度Temperature at discharging condensate排污阀blowdown valve排污箱( 阀) Waste Valves排渣闸阀Scum Gate Valves盘阀moushroom valve盘状阀plate valve旁路阀by pass valve配汽活塞阀缸套piston valve line喷射阀injection valve喷射阀sprayer valve喷水阀spray water valve频跳Chatter平衡阀Balance valves平衡式Balance type平行式闸阀Parallel gate valve Parallel slide valve启闭件Disc启闭压差Blowdown of a safety valve起始升程Commencement of lift气动装置Pneumatic actuator气阀摇臂valve arm气－液动装置Pneumatic-hydraulic actuator潜水电泵( 排污泵) Submerged Motor Pumps切断阀; 截止阀block valve;shut-off valve;stop valve 切断式止回阀stop check valve切换阀; 多向阀changeover valve球、球芯Ball球阀Ball valve球阀globe valve球体Ball全启式安全阀Fall lift safety valve热凝结水排量Hot condensate capacity入口隔离门suction isolating valve塞子Plug三通阀three-way isolating valve三通阀three-way valve三通式Three way type上密封Back seat上密封试验Back seal test渗漏量Leckage升降立式止回阀Vertical lift check valve升降式止回阀Lift check valve适用介质Suitable medium适用温度Suitable temperature手摇油泵( 阀) Manual Oil Pumps Valves疏水阀drain valve双金属片式疏水阀Bimetal elements steam trap 双口排气球Double Opening Exhaust Valves双联弹簧式安全阀Duplex safety valve双闸板Double gate disc双闸板平板闸阀Double Disc Flat Gate Valves 水封闸阀Water Seal Gate Valves水力喷射器( 真空泵) Vacuum Pumps伺服阀servovalve填料Packing填料垫Packing seat填料函填料式旋塞阀Gland packing plug valve填料箱Stuffing box填料压盖Gland通气阀breather valve通气阀；呼吸器breather通用阀门General valve吐出阀；排出阀discharge valve吐出阀限位器delivery valve guard微启式安全阀Low lift safety valve微阻缓闭止回阀Tiny Drag Slow Shut Check Valves吻合度Percent of contact area蜗轮传动蝶阀Butterfly Valves with Gear Actuator蜗轮传动装置Wormgear actuator屋脊式隔膜阀Weir diaphragm valve无阀泵valveless pump无阀隔膜泵valveless diaphragm pump无阀振动泵valveless vibration pump无负荷漏汽量No-load steam loss无负荷漏汽率Rate of no-load steam loss吸（抽）气阀Aspirating valves吸入阀suction valve吸入阀限位器suction valve guard先导式安全阀Pilot operated safety valve先导式液压阀Pilot-operated reducing valve相对静偏差Relative static characteristics derivation相对流量特性偏差Relative flow characteristics derivation相对压力特性偏差Relative pressure characteristics derivation 销轴Hinge pin楔式闸阀Wedge gate valve斜板式蝶阀Indined disc butterfly valve泄料（放空，排污）阀Blowdown valves泄压阀Decompression valves泄压阀pressure release valve泄压阀；安全阀relief valve卸荷式减压阀Balanced reducing valve型号Type Model旋启多瓣式止回阀Multi-disc swing foot valve旋启式止回阀Swing check valve旋启双瓣式底阀Double disc swing foot valve旋塞阀Cock旋塞阀plug valve压力（増压）阀Pressure valve压力调节阀；压力控制阀pressure controlled valve 压力特性Pressure characteristics压力特性偏差Pressure characteristics derivation 压力增长系数Pressure increasing ratio摇杆Arm液动装置Hydraulic actuator液化气管件LPG Pipe Fitting液下泵Under Water Pumps液压执行器hydraulic actuator仪表针形截止阀Meter Needle Type Globe Valves 溢流阀overflow valve翼形阀；锥形阀wing valve油封式旋塞阀Lubricated plug valve有阀翼板double acting wing有阀翼板wing with valve有负荷漏汽量Load steam loss有负荷漏汽率Rate of load steam loss圆板阀；圆盘阀disc valve圆盘式疏水阀Shemostatic team trap圆柱齿轮传动装置Cylindrical gear actuator圆锥齿轮传动装置Conical gear actuator闸板Wedge disc闸板式隔膜阀Wedge diaphragm valve闸阀gate valve闸阀sluice valve针形阀Pintle valve真空破坏阀vacuum breaker valve蒸汽疏水阀Automatic steam trap Trap整定压力Set pressure正向作用式减压阀Direct acting reducing valve支架Yoke直接载荷式安全阀Direct loaded safety valve 直接作用式减压阀Direct-acting reducing valve 直流式Y-globe type直流式截止阀Oblique Stop Valves直通单向阀inline check valve直通单向阀straightway check valve直通阀Throughway Valve止回阀Check Valve止回阀；回流阀reflux valve制动阀Brake valves中压阀门Middle pressure valve钟形浮子式疏水阀Inverted bucket steam trap 钟形罩Inverted bucket轴套Axis Guide主阀Main valve主要外形尺寸Prime out-form dimensions主要性能参数Specifeca tion speeification注液漏斗阀Priming Tundish Valve柱塞阀Plunger valves柱塞截止阀Plunger Globe Valves柱塞型摆动阀rocking plunger valve撞击手轮Impact handwheel锥形阀；翼形阀conical valve自动循环阀Automatic Recirculation Valve组合阀Combination valves最大过冷度Maximum subcoold temperature最大流量Maximum flow rate最大压差Maximum differential pressure最低工作压力Minimum operating pressure最高背压率Maximum rate of back pressure最高工作背压Maximum operating back pressure最高工作温度Maximum operating temperature最高工作压力Maximum operating pressure最高排水温度Maximum temperature at discharging 最高允许温度Maximum allwable temperature 最高允许压力Maximum allowable pressure最小过冷度Minimum subcooled temperature最小压差Minimum differntial pressure。
阀门英语术语对照
第二节阀门术语一、阀门类别（中英文对照）闸阀[Gatevalve;Slidevalve]截止阀[Globevalve;Stopvalve]止回阀[Checkvalve;Non-returnvalve]球阀[Ballvalve]蝶阀[Butterflyvalve]旋塞阀[Plugvalve]节流阀[Throttlevalve]隔膜阀[Diaphragmvalve]针型阀[Pintlemvalve]低温阀[Lowtemperaturevalve]二、结构及零件(中英文对照）结构长度[FacetoFace;EndtoEnd;FacetoEnddimension]结构形式[Typeofconstruction]角式[Angletype]直通式[Throughwaytype]保温式[Steamjackettype]连接形式[Typeofconnecting]电动装置[Electricactuator]气动装置[Pneumaticactuator]齿轮操作[Gearoperation]手轮操作[Handwheel]阀体[Body]阀盖[Bonnet;cover;cap;lid]阀瓣[Disc]闸板[Wedge]阀杆[Stem;Spindle]阀杆螺母[Stemnut;Yokenut]填料函[Stuffingbox]填料压盖[Gland]支架[Yoke]上密封[Backseat]阀座[Seat]螺栓[Blot]螺母[Nut]填料[Packing]球体[Ball]销轴[Hingepin]摇杆[Arm;Hinge]密封面[Sealface]主要性能参数[Specification]公称压力(PN)[Nominalpressure]公称通径（DN）[Nominaldiameter]工作压力[Workingpressure]壳体试验[Shelltest]密封试验[Sealtest]三、其它术语(中英文对照）BW表示对焊连接方式SW表示承插焊连接方式F.P=全通径BB-螺栓连接阀盖PSB-内压自密封阀盖G.O=齿轮操作BG-伞齿轮PWHT-焊后热处理PCD-中心圆直径H.F=硬质面CS-碳钢FS-锻钢AS-合金钢SS-不锈钢CI-铸铁OS&Y-明杆支架结构。
阀门零部件中英文对照
阀门零部件英汉术语对照Axis Guide 轴套Ball 球、球芯Ball seat 密封圈Blowdown Sealing Face 启、阀件密封面Body 阀体Bonnet 阀盖Disc 阀瓣Mut 螺母Screw 螺栓Sealing 密封件Spring 弹簧Stem 阀杆Stem Mut 阀杆螺母Stem seal 填料Wedge Disc 闸板阀门规范技术英语术语对照Applicable medium 适用介质Applicable temperature 适用温度Butt Clamp 对夹Chemical analysis 化学成份Connecting format 连接形式Double disc 双闸板Flexible disc 弹性闸板Flange 法兰 Hoop 卡箍Inside thread 内螺纹Jacket 夹套Mains 电源Material chemical analysis and mechanical capacity材料化学成份和机械性能materials 材料 Materials for main parts 主要零件材料Mechanical capacity 机械性能Max. Discharging Capacity 最大排水量Max. Operating Temperature 最高工作温度Max. Allowable Temperature 最高允许温度Max. Allowable Pressure 最高允许压力Model 型号Name of parts 零件名称nitrogen (N) 氮Nominal bore 公称通径Nominal Pressure 公称压力Nozzle 排气口Outside thread 外螺纹Oxidant 氧化性介质Parallel 平行Piping 管路Piston 活塞Reductant 还原性介质Rising stem 明杆Seal 阀座，密封面Seat testing pressure 压力气密封试验压力Socket 卡套Specifications 性能规范Single disc 单闸板Solid 刚性Strengh testing pressure 强度试验压力Steam , condensate 蒸汽,凝结水Stroke 冲程，行程Water,oil,steam 水,温度,气Wedge 楔式 Welding 焊接阀门材质术语英汉对照Atbas metal 镍铬钢Buna-N rubber 丁晴橡胶Casting aluminium brass 铸铝黄铜Casting aluminium bronze 铸铝青铜Ceramic metal 陶瓷金属Chromel alloy 镍铬合金CHR rubber 氯晴橡胶Chrominm-molybdenum-vanadium steel 铬钼钒钢 Chromium stainless steel 铬不锈钢Chromium-molybdenum steel 铬钼钢Corrugation pad 波形垫Cuprum alloy 铜合金Ductile Cast iron 球墨铸铁Expanded graphite 柔性石墨Fine Steel Casting iron 优质碳素钢Fluorous rubber 氟橡胶Gray Cast iron 灰铸铁Hayne's alloy 钴铬钨合金High tem perature steel 高温钢Monel 蒙乃尔合金Low temperature steel 低温钢Nylon 尼龙塑料Polytetrafluoroethylene(PTEF) 聚四氟乙烯Polythene 聚乙烯Pure aluminium 纯铝Pure cupper 纯铜Rubber graphite board 橡胶石墨板Spring steel 弹簧钢Stainless acid-resisting steel 不锈耐酸钢Stainless and Graphite 不锈钢/石墨Stainless steel 不锈钢Steel Casting iron 碳素钢铸件Shell Test Pressure 壳体试验压力Service Fluid 工作介质。
各种阀门,管件及其部件名称中英文对照表.docx
各种阀门,管件及其部件名称中英文对照表.docx'\\各种阀门、管件及部件名称中英文对照表1螺纹球阀CQ Thread Ball Valves2形三通式pattern three way3形三通式pattern three way4安全阀Safety valve5暗杆闸阀Inside screw nonrising stem type gate valve6百叶窗闸板shutter7百叶窗式挡板louver damper8摆阀式活塞泵swing gate piston pump9保温式Steam jacket type10报警阀alarm valve11报警阀信号阀脉冲阀sentinel valve12背压调节阀back pressure regulating valve13背压率Rate of back pressure14本体阀杆密封body stem seal15波纹管阀Bellows valves16波纹管密封阀bellow sealed valve17波纹管密封式Bellows seal type18波纹管平衡式安全阀Bellows seal balance safety valve 19波纹管式减压阀Bellows reducing valve20波纹管式减压阀Bellows weal reducing valve21薄膜thin film22薄膜隔膜diaphragm23薄膜式减压阀Diaphragm reducing valve24薄型闸阀Thin Gate Valves25不封闭式Unseal type26槽车球阀Tank Lorry Ball Valves27颤振Flutter28常闭式Normally closed type29常开式Normally open type30超低温阀门Cryogenic valve31超高压阀门Super high pressure valve32超过压力Overpressure of a safety valve33衬胶隔膜阀rubber lined diaphragm34衬胶截止阀rubber lined globe valve35垂直板式蝶阀Vertical disc type butterfly valve36磁耦合截止阀Magnetic Co-operate Globe Valves 37带补充载荷的安全阀Supplementary loaded safety valve 38带辅助装置的安全阀Assisted safety valve39单阀碟双面平行密封闸阀parallel single disk gate valve40单口排气阀Single Opening Exhaust Valves41单向阀Non-return Valve42单闸板Single gate disc43单闸板平板闸阀Single Disc Flat Gate Valves44弹簧薄膜式减压阀Spring diaphragm reducing valve 45弹簧式安全阀Direct spring loaded safety valve 46弹簧座Spring plate 47弹性闸板Flexible gate disc48当量计算排量Equivalent calculated capacity49挡板damper50导阀Pilot valve51导向套Valve guide disc guide52低温阀门Sub-zero valve53低压阀门Low pressure valve54底阀bottom valve55底阀Foot valve56电磁动装置Eletro magnetic actuator57电磁阀magnetic valve58电磁阀solenoid valve59电磁－液动装置Eletro magnetichydraulic actuator 60电动阀mortor operated valve61电动阀motorized valve62电动截止阀Electric Actuated Stop Valves63电动平行式双闸板闸板Electric Double Disk Parallel Gate Valves64电动楔式闸阀Electric Actuated Wedge Gate Valves 65电动装置Electric actuator66电－液动装置Eletro hydraulic actuator67电液伺服阀electro-hydraulic servovalve68调节弹簧Regulation spring69调节阀adjusting valve70调节阀control valve71调节阀regulating valve72调节螺套Adjusting bolt Adjusting screw73调节圈Adjusting ring74蝶板Disc75蝶阀；瓣阀butterfly valve76蝶阀；瓣阀；拍门；铰链阀flap valve77蝶式缓冲止回阀Butterfly Type Non-slam Check78蝶式止回阀Butterfly swing check valve79定比减压阀Proprutioning pressure reducing valve80定差减压阀Fixed differential reducing valve 81定值减压阀Fixed pressure reducing valve82动态特性Dynamic characteristics 83对焊连接阀Buttwelding valves84对夹蝶板阀Wafer plate valves85对夹式衬胶蝶阀Wafer Type Butterfly Valves with Rubber Itning86对夹式阀门Clamp valves87对夹式止回阀Wafer Check Valves88额定排量Certified capacity89额定排量系数Derated coefficient of discharge 90二通阀Two-way valves91阀valve92阀板valve deck plate93阀板valve plate94阀板式活塞泵valve deck plate type piston pump 95阀板式活塞泵valve plate type piston pump96阀瓣Disc97阀操纵杆valve operating rod98阀痤槽valve seat recess99阀挡valve grid100阀挡valve positioner101阀挡valve stop102阀导杆valve tail rod103阀导向器valve guide104阀盖bonnet105阀盖衬套bonnet bush106阀盖垫片bonnet gasket107阀杆stem108阀杆valve rod109阀杆valve spindle110阀杆端部尺寸Dimmension of valve stem end 111阀杆环stem ring112阀杆螺母Yoke bushing Yoke nut113阀杆填料stem packing114阀杆头部尺寸Dimension of valve stem head 115阀簧valve spring116阀簧压板valve spring plate117阀控水锤泵valve-controlled hydraulic ram 118阀框架valve yoke119阀门Valve120阀门传动装置valve bandle set121阀门和管件Valves and Fittings122阀门盘根valve packing123阀门手柄valve handle124阀盘disc125阀盘valve disc126阀片Disc127阀球valve ball128阀驱动臂valve driving arm129阀驱动臂valve motion arm130阀式活塞valve type piston131阀式活塞valve type bucket132阀室式活塞泵valve box type piston pump 133阀室式活塞泵（美）valve pot type piston pump 134阀抬起装置valve lifting device135阀体body136阀体valve body137阀箱valve box138阀箱valve cage139阀箱valve chest140阀箱；阀限位器valve guard141阀箱盖cover for valve box142阀箱盖valve box cover143阀箱式活塞泵（美）turret type piston pump 144阀形活塞泵valve type piston pump 145阀座Seat ring146阀座valve carrier147阀座valve seat(body seat)148阀座；阀盘valve seat149阀座环seat ring150阀座密封嵌条sealing strip for valve seat 151法兰flange 152法兰堵头blind flange153法兰端flange end154法兰接头flange joint155法兰连接紧固件（双头螺栓和螺flange bolting 帽）156法兰密封面，法兰面flange facing157法兰面加工flange facing finish158法兰球阀Flange Ball Valves159翻板阀Flap160反冲盘Disc holder161反向作用式减压阀Reverse acting reducing valve 162反向作用式减压阀Reverse acting reducing valve 163放空阀emptying valve164放气阀air vent valve;vent valve165放气阀；排气阀air evacuation valve166放泄阀escape valve167分置阀室式活塞泵separate valve box type piston pump 168分置阀室式活塞泵（美）side pot type piston pump 169封闭式Seal type170浮动式球阀Float ball valve171浮球Ball float172浮球阀Float Valve173浮球式疏水阀Ball float steam trap174浮球式疏水阀Free Float Type Steam Trap175浮桶Bucket float176浮桶式疏水阀Open bucket steam trap177辅助（副）阀Auxiliary valves178负荷率Rate of load condensate179附加背压力Superimposed back pressure180复位弹簧Returnning spring181杠杆式Lever type182杠杆式安全阀Lever and weight loaded safety valve 183杠杆式减压阀Lever reducing valve184高温阀门High temperature valve185高压阀门High pressure valve186格兰密封gland187隔离阀isolating valve188隔膜Diaphragm189隔膜阀diaphragm valve190隔膜式控制阀diaphragm operated comtrol valve 191工作背压Operating back pressure192工作温度Operating temperature193工作温度Working temperature194工作压差Operting differential pressure195工作压力Operating pressure196工作压力Working pressure197公称通径Nominal diameter198公称压力Nominal pressure199固定式球阀Fixed ball valve200关闭压力Lockup pressure201关阀过冷度Subcooled temperature of close valve 202关阀温度Closing valve temperature203管道安全阀Piping Safety Valves204过冷度Subcoold temperature205过流阀或节流阀Restrictor Valves206喉径Throat diameter207滑阀slide valve208滑阀式回转活塞泵rotary piston pump with slide gate209滑阀型转子泵eccentric rotary pump with sliding sleeve210环形阀annular valve211环形阀double beat valve212换向阀selector valve213换向阀shuttle valve214回转滑阀活塞泵piston pump with rotary gate215回座压力Re-seating pressure of a safety valve 216活塞昵减压阀Piston reducing valve217活塞式阀piston valve218活塞式阀；柱塞式阀plunger valve219活塞式减压阀Piston reducing valve220减速阀Deceleration valves221减压比Pressure reducing ratio222减压阀pressure reducing valve223浆液阀Parallel Slide Valves224角阀Angle Valve225角阀isolation valve angle configuration 226角式Angie type227角式节流阀Angle Throttle Valves228角式截止阀Angle Stop valves229铰链阀；片状阀flapper valve230节流阀throttle valve231节流阀choke valve232节流阀；节流throttle233结构长度Face-to-face dimension ;End-to-end dimension; Face-to-centre dimension234结构形式Type of construction235截止阀Globe valve236截止阀Shut-off Valve237截止阀；关断阀shut-off valve238截止式隔膜阀Globe diaphragm valve239紧急切断阀Emergeny Cut-off Valves240进气阀air intake valve241进水阀；进口阀门inlet valve242静态特性Static characteristics243静态特性偏差Static characteristics derivation244开阀过冷度Subcooled temperature of open valve 245开阀温度Opening valve temperature246开启高度Lift247壳体试验Shell test248壳体试验压力Seal test pressure249空气阀门Air valves250快速排污阀Quick Draining Valves251类型Type252冷凝结水排量Cold condensate capacity253冷态试验差压力Cold differential test pressure 254理论排量Theoretical flowing capacity255连接槽尺寸Dimension of connecting channel 256连接尺寸Conncetion cimension257连接形式Type of connection258帘面积Curtain area259流道面积Flow area260流道直径Flow diameter261流量孔板flow orifice plate262流量控制阀flow control valve263流量特性Flow characteristics264流量特性偏差Flow characteristics derivation 265漏汽量Steam loss266脉冲式疏水阀Impulse steam trap267密封面Sealing face268密封试验Seal test269密封试验压力Seal test pressure270明杆平行式双闸板闸板Double Disk Parallel Gate Valves271明杆闸阀Outside screw stem rising through handwheel type gate valve272膜片Diaphragm273内压自封Pressure seat274逆止阀；止回阀check valve275逆止阀；止回阀non-return valve276逆止阀止回阀单向阀check valve277排放背压力Brilt-up back pressure 278排放压力Relieving pressure279排灰阀Ash valves280排量系数Coefficient of discharge 281排气阀air release valve282排气阀Exhaust valves283排气阀Vent Valve284排水阀Drainage valves285排水温度Temperature at discharging condensate286排污阀blowdown valve 287排污箱阀Waste Valves288排渣闸阀Scum Gate Valves 289盘阀moushroom valve 290盘状阀plate valve291旁路阀by pass valve292配汽活塞阀缸套piston valve line293喷射阀injection valve294喷射阀sprayer valve295喷水阀spray water valve296频跳Chatter297平衡阀Balance valves298平衡式Balance type299平行式闸阀Parallel gate valve Parallel slide valve 300启闭件Disc301启闭压差Blowdown of a safety valve302起始升程Commencement of lift303气动装置Pneumatic actuator304气阀摇臂valve arm305气－液动装置Pneumatic-hydraulic actuator306潜水电泵排污泵Submerged Motor Pumps307切断阀截止阀block valve;shut-off valve;stop valve 308切断式止回阀stop check valve309切换阀多向阀changeover valve310球、球芯Ball311球阀Ball valve312球阀globe valve313球体Ball314全启式安全阀Fall lift safety valve315热凝结水排量Hot condensate capacity316入口隔离门suction isolating valve317塞子Plug318三通阀three-way isolating valve319三通阀three-way valve320三通式Three way type321上密封Back seat322上密封试验Back seal test323渗漏量Leckage324升降立式止回阀Vertical lift check valve325升降式止回阀Lift check valve326适用介质Suitable medium327适用温度Suitable temperature328手摇油泵阀Manual Oil Pumps Valves329疏水阀drain valve330双金属片式疏水阀Bimetal elements steam trap 331双口排气球Double Opening Exhaust Valves 332双联弹簧式安全阀Duplex safety valve333双闸板Double gate disc334双闸板平板闸阀Double Disc Flat Gate Valves 335水封闸阀Water Seal Gate Valves336水力喷射器真空泵Vacuum Pumps337伺服阀servovalve338填料Packing339填料垫Packing seat340填料函Stuffing341填料式旋塞阀Gland packing plug valve342填料箱Stuffing box343填料压盖Gland344通气阀breather valve345通气阀；呼吸器breather346通用阀门General valve347吐出阀；排出阀discharge valve348吐出阀限位器delivery valve guard349微启式安全阀Low lift safety valve350微阻缓闭止回阀Tiny Drag Slow Shut Check Valves 351吻合度Percent of contact area352蜗轮传动蝶阀Butterfly Valves with Gear Actuator 353蜗轮传动装置Wormgear actuator354屋脊式隔膜阀Weir diaphragm valve355无阀泵valveless pump356无阀隔膜泵valveless diaphragm pump357无阀振动泵valveless vibration pump358无负荷漏汽量No-load steam loss359无负荷漏汽率Rate of no-load steam loss360吸（抽）气阀Aspirating valves361吸入阀suction valve362吸入阀限位器suction valve guard363先导式安全阀Pilot operated safety valve364先导式液压阀Pilot-operated reducing valve365相对静偏差Relative static characteristics derivation366相对流量特性偏差Relative flow characteristics derivation367相对压力特性偏差Relative pressure characteristics derivation368销轴Hinge pin369楔式闸阀Wedge gate valve370斜板式蝶阀Indined disc butterfly valve 371泄料（放空，排污）阀Blowdown valves372泄压阀Decompression valves 373泄压阀pressure release valve374泄压阀；安全阀relief valve375卸荷式减压阀Balanced reducing valve376型号Type Model377旋启多瓣式止回阀Multi-disc swing foot valve378旋启式止回阀Swing check valve379旋启双瓣式底阀Double disc swing foot valve380旋塞阀Cock381旋塞阀plug valve382压力（増压）阀Pressure valve383压力调节阀；压力控制阀pressure controlled valve384压力特性Pressure characteristics385压力特性偏差Pressure characteristics derivation 386压力增长系数Pressure increasing ratio387摇杆Arm388液动装置Hydraulic actuator389液化气管件LPG Pipe Fitting390液下泵Under Water Pumps391液压执行器hydraulic actuator392仪表针形截止阀Meter Needle Type Globe Valves 393溢流阀overflow valve394翼形阀；锥形阀wing valve395油封式旋塞阀Lubricated plug valve396有阀翼板double acting wing397有阀翼板wing with valve398有负荷漏汽量Load steam loss399有负荷漏汽率Rate of load steam loss400圆板阀；圆盘阀disc valve401圆盘式疏水阀Shemostatic team trap402圆柱齿轮传动装置Cylindrical gear actuator403圆锥齿轮传动装置Conical gear actuator404闸板Wedge disc405闸板式隔膜阀Wedge diaphragm valve406闸阀gate valve407闸阀sluice valve408针形阀Pintle valve ; Needle valve409真空破坏阀vacuum breaker valve410蒸汽疏水阀Automatic steam trap Trap411整定压力Set pressure412正向作用式减压阀Direct acting reducing valve 413支架Yoke414直接载荷式安全阀Direct loaded safety valve 415直接作用式减压阀Direct-acting reducing valve 416直流式Y-globe type417直流式截止阀Oblique Stop Valve418直通单向阀inline check valve419直通单向阀straightway check valve420直通阀Throughway Valve421止回阀Check Valve422止回阀；回流阀reflux valve423制动阀Brake valves424中压阀门Middle pressure valve425钟形浮子式疏水阀Inverted bucket steam trap 426钟形罩Inverted bucket427轴套Axis Guide428主阀Main valve429主要外形尺寸Prime out-form dimensions 430主要性能参数Specifeca tion speeification 431注液漏斗阀Priming Tundish Valve432柱塞阀Plunger valve433柱塞截止阀Plunger Globe Valve434柱塞型摆动阀rocking plunger valve435撞击手轮Impact handwheel436锥形阀；翼形阀conical valve437自动循环阀Automatic Recirculation Valve438组合阀Combination valves439最大过冷度Maximum subcoold temperature 440最大流量Maximum flow rate441最大压差Maximum differential pressure442最低工作压力Minimum operating pressure443最高背压率Maximum rate of back pressure444最高工作背压Maximum operating back pressure 445最高工作温度Maximum operating temperature 446最高工作压力Maximum operating pressure447最高排水温度Maximum temperature at discharging 448最高允许温度Maximum allwable temperature449最高允许压力Maximum allowable pressure450最小过冷度Minimum subcooled temperature 451最小压差Minimum differntial pressure。
阀门相关术语英汉对译
配管法兰：JB79 GB9112～9131实验与检验：GB/T13927―92性能规范（美标
压力-温度等级：ANSIB16.34 实验与检验：AP1598
门地主要零件有采用塑料橡胶等非金属材料或力学性能和温度极限低于表中地材料
阀门技术参数
配管法兰：JB79 GB9112～9131实验与检验：GB/T13927―92性能规范（美标
压力-温度等级：ANSIB16.34 实验与检验：AP1598
门地主要零件有采用塑料橡胶等非金属材料或力学性能和温度极限低于表中地材料
阀门技术参数
性能规范：配管法兰：JB79 GB9112～9131实验与检验：GB/T13927―92性能规范（美标
压力-温度等级：ANSIB16.34 实验与检验：AP1598
结构长度：GB12221 配管法兰：JB79 GB9112～9131实验与检验：GB/T13927―92
结构长度：ANSIB16.10 配管法兰：ANSIB16.5 GB9112～9131 压力-温度等级：ANSIB16.34 实验与检验：AP1598
注：1、当工作温度为表中温度级中间值时，可用内插法决定最大工作压力.2、当阀门地主要零件有采用塑料橡胶等非金属材料或力学性能和温度极限低于表中地材料时，不能使用此表. 3、如用户需要详细技术资料及尺寸，请向本公司技术部索取。
阀门中文英文专业术语
Grounding ball 基座球体Mud box污泥箱Sight glass视镜，观察孔Single acting 单作用的；单动的；单动式Gland follower 填料盖；密封压盖随动件SG iron spheroidal graphite cast iron 球墨铸铁DIN deutsche industrie-norm （德）西德工业标准Expansion joint 伸缩接头BB bolted bonnet 螺栓连接阀盖OS &Y Outside screw & Yoke 明杆带支架Manifold valve 汇流阀Housing 阀体Union type bonnet 活接头阀盖Sewage 污水，下水道（系统）Position indicator 位置指示器Ditto 同上NPT national standard pipe taper thread 美国标准锥管螺纹QA quality assurance 质量保证QC quality control 质量控制Steam condensate 冷凝蒸汽Freight collect 到付Charpy impact test 夏比冲击试验（摆锤冲击试验）PSI product support instruction 产品供应说明书Stuffing box 填料箱Flat face flange 平面法兰Tensile test 拉伸试验Prime paint 底漆Fig. No。
figure number 图表数据Data book 数据手册Solid wedge gate valve楔式单闸板闸阀Bolted gland 螺栓连接式填料压盖W．O．G water oil gas 水、油、气（阀门介质）Design condition 设计工况Galvanized 镀锌Split body组合（分）体Split body ball valve组合式球阀Blind flange 盲板法兰Tapping 攻（螺）丝；钻孔，开孔；导出流体Serrated gasket锯齿形垫片Black pipe 非镀管，无镀层管Retaining ring 卡环、挡圈End connection 端部连接Gunmetal 锡锌青铜、炮铜SBR styene-butadiene rubber 苯乙烯聚丁橡胶EPR ethylene propylene rubber 聚乙丙烯橡胶Short pattern 短型Double offset 双效补偿Chevron gear 人字齿轮Limit stop 极限开关、终点开关，限制器，止动器，挡块Operating force 操纵力，控制力Spindle 阀杆Corrosion protection 防蚀Fusion bonded 熔接的Expoxide resin 环氧树脂Film thickness油膜厚度Pinhole销孔；针孔Foreign matter 进口器材、杂质Spark test 火花试验（鉴别）Legibly 易读地；明了地Durably 经久地，坚牢地Identification mark标志（识别），商标Body end（阀体）连接端Adequate shielding 安全屏蔽Cathodic corrosion 阴极腐蚀Rubber lined衬胶Liner衬垫[套，里]，炉衬Piston liner 活塞缸Refractory liner耐火材料衬里RTJ ring type joint 环连接TM，twisting moment 扭矩Limiting conditions 极限状态SF，steel forged 锻钢Perforation 钻（穿，打）孔Hexagon nut 六角螺母Blow-out proof stem防泄漏阀杆Non-slam valve 缓冲阀BF：blind flange 盲板法兰ACC：accessories附件SCRD：screwed螺纹SW：socket welding 承插焊C．S：carbon steel 碳钢BW：butt welding 对焊S．O．F：slip-on flange 松套法兰LP：long pattern 长系列Wrought iron 熟铁，锻铁Pig iron 生铁Blast furnace 高炉Flaky 片状的。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
关键字：阀门1.阀门种类术语AngleStopValves角式截止阀AngleThrottleValves角式节流阀AngleTypeGlobeValves角式截止阀ButterflyTypeNon-slamCheck蝶式缓冲止回阀ButterflyValveswithGearActuator蜗轮传动蝶阀Cock二通CQThreadBallValvesCQ螺纹球阀DiaphragmValves隔膜阀DoubleDiscFlatGateValves双闸板平板闸阀DoubleDiskParallelGateValves明杆平行式双闸板闸板DoubleOpeningExhaustValves双口排气球ElectricActuatedStopValves电动截止阀ElectricActuatedWedgeGateValves电动楔式闸阀ElectricDoubleDiskParallelGateValves电动平行式双闸板闸板EmergenyCut-offValves紧急切断阀FreeFloatTypeSteamTrap浮球式疏水阀FlangeBallValves法兰球阀FlangeGateValves法兰闸阀FlangeGlobeValves法兰截止阀GaugeValves仪表阀HardSealButterflyValves金属密封碟阀HighTemperaturePressurePowerStationGateValves高温高压电站闸阀HighTemperaturePressurePowerStationGlobeValves高温高压电站截止阀LiftCheckValves升降式止回阀LiftCheckValves升降式止回阀LiningBallValves衬里球阀LiningButterflyValves衬里碟阀LiningCheckValves衬里止回阀LiningCock衬里二通LiningGlobeValves衬里截止阀LiningT-CockValves衬里三通旋塞阀LiquidIndicator液位计LPGPipeFitting液化气管件MagneticCo-operateGlobeValves磁耦合截止阀MagnetismForlePumps磁力泵ManualOilPumpsValves手摇油泵(阀) MeterNeedleTypeGlobeValves仪表针形截止阀ObliqueStopValves直流式截止阀ParalleslSlideValves浆液阀PipingCentrifugalPumps管道离心泵PipingPumps管道泵PipingSafetyValves管道安全阀PlungerGlobeValves柱塞截止阀QuickDrainingValves快速排污阀RestrictorValves过流阀(或节流阀)SafetyValves安全阀ScrewPumps螺杆泵ScumGateValves排渣闸阀SingleDiscFlatGateValves单闸板平板闸阀SingleOpeningExhaustValves单口排气球SlurryPumps泥浆泵StopValves截止阀Strainer过滤器SubmergedMotorPumps潜水电泵(排污泵) SwingCheckValves旋启式止回阀SwingCheckValves旋启式止回阀TankLorryBallValves槽车球阀T-Cock三通ThinGateValves薄型闸阀ThrottleValves节流阀TinyDragSlowShutCheckValves微阻缓闭止回阀UnderWaterPumps液下泵VacuumPumps水力喷射器(真空泵) VerticalLiftCheckValves立式止回阀WaferCheckValves对夹式止回阀WaferTypeButterflyValveswithRubberItning对夹式衬胶蝶阀WasteValves排污箱(阀)WaterSealGateValves水封闸阀WedgeGateValves楔式闸阀YTypeandCylinderFiltersY型筒型过滤器2.零部件术语AxesGuide轴套Ball球、球芯Ballseat密封圈BlowdownSealingFace启、阀件密封面Body阀体Bonnet阀盖Disc阀瓣Mut螺母Screw螺栓Sealing密封件Spring弹簧Stem阀杆StemMut阀杆螺母Stemseal填料WedgeDisc闸板3.性能术语Applicablemedia适用介质Applicabletempure适用温度ButtClamp对夹Chemicalanaiysis化学成份Connectingformat连接形式Doubledisc双闸板Flexibledisc弹性闸板Flange法兰Hoop卡箍Insidetheread内螺纹Materialchemicalanalysisandmechanicalcapacity材料化学成份和机械性能materials材料Materialsformainparts主要零件材料Mechanicalcapacity机械性能Max.DischargingCapacity最大排水量Max.OperatingTemperature最高工作温度Max.AllowableTemperature最高允许温度Max.AllowablePressure最高允许压力Model型号Nameofparts零件名称NominalPressure公称压力Outsidetheread外螺纹Oxidant氧化性介质Parallet平行Reductant还原性介质Risingstem明杆Seattestingpressure压力气密封试验压力Socket卡套Specifications性能规范Singledisc单闸板Solid刚性Strenghtestingpressure强度试验压力Steam,condensate蒸汽,凝结水Water,oil,steam水,温度,气Wedge楔式Welding焊接4.材料术语Buna-Nrubber丁晴橡胶Castingaluminiumbrass铸铝黄铜Castingaluminiumbronze铸铝青铜CHRrubber氯晴橡胶Chrominm-molybdenum-vanadiumsteel铬钼钒钢Chromiumstainlesssteel铬不锈钢Chromium-molybdenumsteel铬钼钢Corrugationpad波形垫Cuprumalloy铜合金DuctileCastiron球墨铸铁Expandedgraphite柔性石墨FineSteelCastingiron优质碳素钢Fluorousrubber氟橡胶GrayCastiron灰铸铁Hayne’salloy钴铬钨合金Hightemperaturesteel高温钢Lowtemperaturesteel低温钢Nylon尼龙塑料Polytetrafluoroethylene聚四氟乙烯Purealuminum纯铝Purecupper纯铜Rubbeergraphiteboard橡胶石墨板Springsteel弹簧钢Stainlessacid-resistingsteel不锈耐酸钢StainlessandGraphite不锈钢/石墨Stainlesssteel不锈钢SteelCastingiron碳素钢铸件ShellTestPressure壳体试验压力ServiceFluid工作介质阀门零部件Axis Guide 轴套Ball 球、球芯Ball seat 密封圈Blowdown Sealing Face 启、阀件密封面 Body 阀体Bonnet 阀盖Disc 阀瓣Mut 螺母Screw 螺栓Sealing 密封件Spring 弹簧Stem 阀杆Stem Mut 阀杆螺母Stem seal 填料Wedge Disc 闸板英语阀门Atbas metal 镍铬钢Buna-N rubber 丁晴橡胶Casting aluminium brass 铸铝黄铜Casting aluminium bronze 铸铝青铜Ceramic metal 陶瓷金属Chromel alloy 镍铬合金CHR rubber 氯晴橡胶Chrominm-molybdenum-vanadium steel 铬钼钒钢Chromium stainless steel 铬不锈钢Chromium-molybdenum steel 铬钼钢Corrugation pad 波形垫Cuprum alloy 铜合金Ductile Cast iron 球墨铸铁Expanded graphite 柔性石墨Fine Steel Casting iron 优质碳素钢Fluorous rubber 氟橡胶Gray Cast iron 灰铸铁Hayne’s alloy 钴铬钨合金High tem perature steel 高温钢Monel 蒙乃尔合金Low temperature steel 低温钢Nylon 尼龙塑料Polytetrafluoroethylene(PTEF) 聚四氟乙烯Polythene 聚乙烯Pure aluminium 纯铝Pure cupper 纯铜Rubber graphite board 橡胶石墨板Spring steel 弹簧钢Stainless acid-resisting steel 不锈耐酸钢Stainless and Graphite 不锈钢/石墨Stainless steel 不锈钢Steel Casting iron 碳素钢铸件Shell Test Pressure 壳体试验压力Service Fluid 工作介质。