LCD manual
7inch Capacitive Touch LCD User Manual
7inch Capacitive Touch LCDUser ManualChinese website: English website: Data download: /wiki Shenzhen Waveshare Electronics Ltd. Co.7inch Capacitive Touch LCD User ManualContents1.Overview (1)1.1AT070TN92 (1)1.2FT5X06 (3)2.Hardware description (6)3.Software dscription (10)4.Test result (12)5.Dimensions (12)1. Overview7inch Capacitive Touch LCD module is a 7 inch TFT-LCD with no LCD controller included. It adopts AT070TN92 as its LCD screen and FT5206GE1 (FT5x06 series ICs) as capacitive touch control chip, supporting multi-touch of up to 5 points. AT070TN92 can provide 800*480 pixel resolution with 24 bit pixel depth.1.1 AT070TN92controller is not included in this LCD. Here is the basic sequence of AT070TN92:Here are the meanings of symbols in the sequence diagram:Remarks:(1) Unit: CLK=1/f CLK, it is the duration for scanning a pixel; H=th, it is the duration forscanning a line.(2) This table is referenced from AT070TN92.pdfFrom the table above, we can see that:The clock of this LCD is come from an external clock source with the frequency of 26.4-46.8MHz. Notices that thfp+thb=46 and tvfp+tvb=23.From the figure above, we can learn that:The total time for scanning a line is: th = thp + thb + thd + thf; in the period of thd, when a clock plus comes, a pixel data will be transmitted via the parallel data interface. And there are 800 pixels each line for this LCD, so thd=800;The duration for scanning a frame is: tv = tvp + tvb + tvd + tvf;Hsync can be regarded as the clock of vertical signals. A clock cycle of Hsync refers to the duration for LCD displaying a line. When a falling edge comes in Hsync, a new line will be displayed in the LCD. However, the actual data transmission only occurs in the period of tvd. And the LCD will display the new line in this case merely. There are 480 lines for this LCD, so tvd = 480. Other parameters can be modified as required, according to the specifications listed in the tables above.1.2 FT5X06Optional interface: I2C/SPI (This module only has I2C interface);Working voltage: 2.8V-3.6V;Built-in 8051 based MCU with 32KB Program Memory, 6KB Data Memory and 256B Internal Data Space;Working temperature range: -40℃-85℃;Supports multi-touch of up to 5 points.I2C Read/Write Timing of FT5X06The figures below show the I2C read/write timing of FT5X06.Writes N bytes to I2C slaveReads N bytes from I2C slaveRegisters of FT5X06The MCU of FT5X06 can read the positions(x, y coordinates) of up to 5 points from the corresponding registers, when the working mode is configured. The following section will present the major registers of FT5X06. For other registers, please refer to FT5X06 Data Sheet.DEVIDE_MODE: FT5x06 mode configuration register; DEVIDE_MODE[6:4] can set three modes: Operating Mode, System Information Mode (reserved) and Testing Mode for reading raw data (reserved). Normally, Operating Mode is always set to read the positions of touch points.TD_STAaddressTOUCHn_XH (n=1-5): This register describes the MSB of the X coordinate of the nth touch point and the corresponding flag, in which the upper two bits of the register indicate the status of the nth touch point, and the lower four bits indicate the MSB of the touchTOUCHn_XL(n=1-5): This register describes the LSB of the X coordinate of the nth touch pointTOUCHn_YH(n=1-5): This register describes the MSB of the Y coordinate of the nth touch point and the corresponding ID, in which the upper four bits of the register indicate the corresponding ID of the nth touch point, and the lower four bits indicate the MSB of the touch point Y position.TOUCHn_YL(n=1-5): This register describes the LSB of the Y coordinate of the nth touch pointFT5x06 data reading flowInitialize I2C;Set the working mode of FT5x06;If there is touch interrupt, read out the corresponding X and Y position values of the touch point(s) from relative register.Notices: For adjacent points, the register addresses of their positions(X and Y coordinates) are not contiguous. For example, touch points A and B are two adjacent points. The position of point A will be stored in the register addresses of 0x03, 0x04, 0x05 and 0x06, and point B in 0x09, 0x0A, 0x0B and 0x0C. The addresses 0x07 and 0x08 are assigned no value.2. Hardware descriptionPin definitions of capacitive touch LCD:Pin24 B3The following figures show the connection of the LCD hardware interfaces based on Open429I-C development board.The hardware connection presented above is based on the TFT-LCD controller integrated in the STM32F429IGT6. In this application, the display is controlled by STM32F429IGT6. MCU reads/writes data from/to the capacitive touch control chip FT5X06 via I2C.In this application, SDRAM serves as the data buffer of LCD. TFT-LCD controller reads data from SDRAM and displays what it got on LCD. The data will be refreshed by the controller all the time, so when there is any change in SDRAM, the picture displayed on the LCD will be updated immediately. Hence, you only need to configure the registers of the TFT-LCD controller, and then manage the data in SDRAM to control the display on the LCD screen. The refresh frequency depends on the LCD clock cycle.The interfaces of the capacitive touch function are shown as follow.3. Software descriptionThe following program is written based on the application developed with Open407I-C. The MCU of Open407I-C development board is STM32F429IGT6, which integrates a TFT-LCD controller with 800*600 pixel resolution.The controller integrated in STM32F429IGT6 is as the figure below shows.HBP is for horizontal back porch and HFP is for horizontal front porch;VBP is for vertical back porch and VFP is for vertical front porch.- HSYNC Width and VSYNC Height: HSYNC Width is for Horizontal Synchronization Width and VSYNC Height is Vertical Synchronization Height. They can be set by the bits HSW(LTDC_SSCR[27:16]) and VSH(LTDC_SSCR[10:0]) of LTDC_SSCR register, where HSW= HSYNC Width – 1, and VSH = VSYNC Height – 1;- HBP and VBP can be set by the bits AHBP(LTDC_BPCR[27:16]) and AVBP(LTDC_BPCR[10:0]) of LTDC_BPCR register, where AHBP= HSYNC Width + HBP – 1, and AVBP= VSYNC Height + VBP – 1;- Active Width and Active Height can be set by the bits AAW(LTDC_AWCR[27:16]) and AAH(LTDC_AWCR[10:0]) of LTDC_AWCR register, where AAW= HSYNC Width + HBP+ Active Width – 1, and AAH= VSYNC Height + VBP+ Active Height – 1;- Total Width and Total Height can be set by the bits TOTALW(LTDC_TWCR[27:16]) and TOTALH(LTDC_TWCR[10:0]) of LTDC_TWCR register, where TOTALW= HSYNC Width + HBP+ Active Width +HFP – 1, and TOTALH= VSYNC Height + VBP+ Active Height +VFP – 1.Program flow chart:4. Test result5. Dimensions。
IMC LCD主显示面板说明说明书
IMC LCD MASTER DIGITAL DISPLAY PANEL connects to the DAT an RJ-45 jack and is supplied with a 3 foot long cable that can be substituted with a standard CAT5 cable up to150 feet long. These ethernet cables are available at most “electronic” retail stores. The display panel also has a PEAK RESET button located on the side to reset previous STORAGE temperature peaks.The Information listed here is for the Eagle 2 Differential Control. Other controllers will display as indicated in their respective instruction manual.COLLECTOR TEMPERATURE STORAGE TEMPERATUREDIFFERENTIAL CONTROL SETTING HI LIMIT CONTROL SETTING PUMP STATUSUPPER LIMIT STA TUSaster LCD has a second page that willAGE/RESET The auxiliary sensors will be displayed within 2 seconds. T o RESET the STORED PEAK temperatures of the storage tank, press and hold for 6 seconds the PAGE/RESET button. The ACTUAL SIZE DISPLAYwhen printed booklet size COL=174.1STO= 1 10 . 4PKH =18 0.4 P KL= 6 0 . 1AX1=-10.5AX2= 17 5 . 3PMP= O N UPL=ONDESCRIPTION:REMOTE “LCD” DISPLAY WITH 4 x 20 CHARACTERS FOR USE WITH EAGLE 1, 2 & D1. NOT FOR USE WITH D2 OR “WEB” CONTROLLER.USE THE 3 FT CAT-5 CABLE INCLUDED OR THE SAME TYPE UP TO 150 FT LONG . WHEN DISCONNECTING THE CAT-5 PLUG FROM THIS UNIT A SMALL SCREWDRIVER MAY BE REQUIRED TODEPRESS THE LEVER ON THE CONNECTOR. DO NOT PULL THE CABLE WITHOUT PROPER LEVER RELEASE OR DAMAGE WILL OCCUR.(-BE) OPTION INDICATES RJ-45 RECEPTACLE IS LOCATED INSIDE UNIT FOR BACKSIDE CABLE ENTRY . REMOVE COVER SCREWS TO ACCESS.THIS PRODUCT IS DESIGNED FOR PERMANENT INSTALLATION.IF IT WILL BE USED AS A PORTABLE SERVICE TOOL, INST ALL A CLEAR STRONG SHEET OVER THE DISPLAY SIDE OF THE UNIT TO PROTECT THE LABEL WINDOW AND “LCD” FROM DAMAGE.READ DISPLAY INSTRUCTIONS FOUND IN CONTROLLER’S SERVICE MANUAL OR VISIT OUR WEBSITE: DAMAGE CAUSED BY IMPROPER USE OR INSTALLATION WILL NOT BE REPAIRED UNDER WARRANTY .IMC INSTRUMENTS, INC.PRODUCT #: SOLR-RD80 & -BEIMC LCD MASTER DIGITAL DISPLAY PANEL connects to the DAT an RJ-45 jack and is supplied with a 3 foot long cable that can be substituted with a standard CAT5 cable up to150 feet long. These ethernet cables are available at most “electronic” retail stores. The display panel also has a PEAK RESET button located on the side to reset previous STORAGE temperature peaks.The Information listed here is for the Eagle 2 Differential Control. Other controllers will display as indicated in their respective instruction manual.COLLECTOR TEMPERATURE STORAGE TEMPERATUREDIFFERENTIAL CONTROL SETTING HI LIMIT CONTROL SETTING PUMP STATUSUPPER LIMIT STA TUSPEAK HI= MAXIMUM TEMPERATURE aster LCD has a second page that willAGE/RESET The auxiliary sensors will be displayed within 2 seconds. T o RESET the STORED PEAK temperatures of the storage tank, press and hold for 6 seconds the PAGE/RESET button. The ACTUAL SIZE DISPLAYwhen printed booklet size COL=174.1STO= 1 10 . 4PKH =18 0.4 P KL= 6 0 . 1AX1=-10.5AX2= 17 5 . 3PMP= O N UPL=ONDESCRIPTION:REMOTE “LCD” DISPLAY WITH 4 x 20 CHARACTERS FOR USEWITH EAGLE 1, 2 & D1, D2. NOT FOR USE WITH “WEB” E THE 3 FT CAT-5 CABLE INCLUDED OR THE SAME TYPE UP TO 150 FT LONG . WHEN DISCONNECTING THE CAT-5 PLUG FROM THIS UNIT A SMALL SCREWDRIVER MAY BE REQUIRED TODEPRESS THE LEVER ON THE CONNECTOR. DO NOT PULL THE CABLE WITHOUT PROPER LEVER RELEASE OR DAMAGE WILL OCCUR.(-BE) OPTION INDICATES RJ-45 RECEPTACLE IS LOCATED INSIDE UNIT FOR BACKSIDE CABLE ENTRY . REMOVE COVER SCREWS TO ACCESS.THIS PRODUCT IS DESIGNED FOR PERMANENT INSTALLATION.IF IT WILL BE USED AS A PORTABLE SERVICE TOOL, INST ALL A CLEAR STRONG SHEET OVER THE DISPLAY SIDE OF THE UNIT TO PROTECT THE LABEL WINDOW AND “LCD” FROM DAMAGE.READ DISPLAY INSTRUCTIONS FOUND IN CONTROLLER’S SERVICE MANUAL OR VISIT OUR WEBSITE: DAMAGE CAUSED BY IMPROPER USE OR INSTALLATION WILL NOT BE REPAIRED UNDER WARRANTY .IMC INSTRUMENTS, INC.PRODUCT #: SOLR-RD84 & -BE。
AOC U27U2 U27U2D Q27U2 Q27U2D 液晶顯示器使用手冊说明书
LCD顯示器使用手冊U27U2 U27U2DQ27U2 Q27U2D TM安全性 (1)符號慣例 (1)電源 (2)安裝 (3)清潔 (4)其他 (5)安裝 (6)包裝內容 (6)安裝支架與底座 (7)調整視角 (8)連接顯示器 (9)壁掛安裝 (10)調整 (11)快捷鍵 (11)OSD Setting (OSD 設定) (13)Luminance (亮度) (14)Color Setup (色彩設定) (16)Picture Boost (圖片增強) (18)OSD Setup (OSD 設定) (19)PIP Setting (PIP 設定)(U27U2/U27U2D) (20)Game Setting (遊戲設定) (21)Extra (其他) (23)Exit (退出) (24)LED 指示燈 (25)故障排除 (26)規格 (27)一般規格 (U27U2/U27U2D) (27)一般規格 (Q27U2/Q27U2D) (28)預設顯示模式(U27U2/U27U2D) (29)預設顯示模式(Q27U2/Q27U2D) (30)隨插即用 (32)安全性符號慣例下列子章節說明本文件中使用的符號慣例。
附註、注意及警告事項本指南中的文字區塊會伴隨圖示,以粗體或斜體列印。
這些區塊屬於附註、注意及警告事項,使用方式如下:附註:「附註」代表重要資訊,可協助您更有效利用電腦系統。
注意:「注意」代表會對硬體造成潛在的損害或資料遺失,並告知您如何避免此類問題。
警告:「警告」代表存在人身傷害的可能性,並告知您如何避免此類問題。
有些警告可能會以另一格式顯示,也可能無圖示伴隨顯示。
在此情況下,警告會以管理單位規定的特定顯示方式顯示。
本顯示器限制使用標籤所示的電源。
如不明住家使用的電源種類,請洽經銷商或當地的電力公司。
.本顯示器配備三腳(第三支接腳用於接地)接地插頭。
此種插頭因安全功能,僅適用接地插座。
插座如無三腳接地插孔,可請電工安裝正確插座,或用轉接頭將顯示器妥善安全接地。
Hikvision LCD显示器用户手册说明书
User ManualUser ManualCOPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co., Ltd.ALL RIGHTS RESERVED.Any and all informa ti on, including, among others, wordings, pictures, graphs are the proper ti es of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereina ft er referred to be “Hikvision”). This user manual (hereina ft er referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, par tiall y or wholly, by any means, without the prior wri tt en permission of Hikvision. Unless otherwise s ti pulated, Hikvision does not make any warran ti es, guarantees or representa ti ons, express or implied, regarding to the Manual.About this ManualThis Manual is applicable to the Monitor.The Manual includes instruc ti ons for using and managing the product. Pictures, charts, images and all other informa ti on hereina ft er are for descrip ti on and explana ti on only. The informa ti on contained in the Manual is subject to change, without no ti ce, due to firmware updates or other reasons. Please find the latest version in the company website (h tt p:///en/).Please use this user manual under the guidance of professionals.Trademarks Acknowledgementand other Hikvision’s trademarks and logos are the proper ti es of Hikvision in various jurisdic ti ons. Other trademarks and logos men ti oned below are the proper ti es of their respec ti ve owners.Legal DisclaimerTO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW,Regulatory Informa ti onFCC Informa ti onPlease take a tt en ti on that changes or modifica ti on not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec ti on against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc ti on manual, may cause harmful interference to radio communica ti ons. Opera ti on of this equipment in a residen ti al area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.FCC Condi ti onsThis device complies with part 15 of the FCC Rules. Opera ti on is subject to the following two condi ti ons:1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired opera ti on.EU Conformity StatementThis product and - if applicable - the supplied accessories too are marked with"CE" and comply therefore with the applicable harmonized European standards listed under the EMC Direc ti ve 2014/30/EU, the LVD Direc ti ve 2014/35/EU, the RoHS Direc ti ve 2011/65/EU.2012/19/EU (WEEE direc ti ve): Products marked with this symbol cannot bedisposed of as unsorted municipal waste in the European Union. For properrecycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collec ti on points. For more informa ti on see: 2006/66/EC (ba tt ery direc ti ve): This product contains a ba tt ery that cannot bedisposed of as unsorted municipal waste in the European Union. See theproduct documenta ti on for specific ba tt ery informa ti on. The ba tt ery is marked with this symbol, which may include le tt ering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the ba tt ery to your supplier or to a designated collec ti on point. For more informa ti on see: Industry Canada ICES-003 ComplianceThis device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.Applicable ModelsThis manual is applicable to the model: LCD Monitor.Symbol ConventionsThe symbols that may be found in this document are defined as follows. Symbol DescriptionProvides addi ti onal informa ti on to emphasize or supplement important points of the main text.Indicates a poten ti ally hazardous situa ti on, which if not avoided, could result in equipment damage, data loss, performance degrada ti on, or unexpected results.Indicates a hazard with a high level of risk, which if not avoided, will result in death or serious injury.Table of contentsFOR YOUR SAFETY (1)Precautions (1)Special precautions for LCD monitor (2)BEFORE YOU OPERATE THE MONITOR (3)Installation instruction (4)Cable connection (5)Adjusting the viewing angle (6)Operating instructions (7)General operating instructions (7)Front panel control (8)How to adjust settings (9)Adjusting the picture (10)Plug and play (12)TECHNICAL SUPPORT (FAQ) (13)APPENDIX (15)Specifications (15)Factory presetting table (17)Connector pin assignment (18)FOR YOUR SAFETYPlease read this manual carefully before using this monitor. Please keep it properly for further refer-ence.Warning:To avoid fire or electric shock, the monitor must not be exposed to the rain or moisture. The monitor has dangerous high voltage inside. Do not open the casing. Repair can only be performed by qualified professionals.Notes• Do not install the monitor in places near heat (e.g. heater or air hose) or easily exposed todirect sunlight, or dusty areas, or places easily affected by mechanical vibration or shock.• Please keep the original shipping carton and packaging material properly. These come in handy when carrying the monitor.• Please repackage the monitor like the way it was packaged for shipping to ensure the bestprotection.• Clean the monitor with a soft cloth regularly to keep it new. Slightly soak the soft cloth with neutral detergent to remove stubborn stains. Do not use strong solution, such as thinner,toluene or abrasive cleaner; otherwise the casing would be damaged. Please pull out the plug of the monitor before cleaning for safety concerns.• Do not scratch the screen with hard objects; otherwise permanent damage may occur.• Keep liquid out; otherwise component damage may occur.Precautions• Do not use the monitor near water, such as places near the sink, wash bowl, kitchen sink,laundry sink, swimming pool or damp basement.• Do not place the monitor on an unstable cart, base or table. Human injury and severe damage to the device may occur if the monitor falls. Only use the cart or base recommended by the manufacturer or sold with the monitor.• The notches and openings at the back and bottom of casing are for ventilation. Make sure that these openings are not blocked to ensure stable operation and avoid overheating. Do not place the monitor in a bed, on a sofa, carpet or a similar surface. Do not place the monitor near or above a heater or heating controller. Do not place the monitor on a bookshelf or in a cabinet set unless proper ventilation is available.• Only use the type of power supply specified on the name plate. If you are not sure of the type of power supply in your home, consult your product dealer or local power company.• This monitor is equipped with a three-pin plug (a plug that comes with an earthing pin). This plug is for the socket with earthing protection only. If this socket does not support the three-pin plug, please ask an electrician to install a correct socket or use an adapter to ground thedevice safely. Do not damage the safety function of the earth plug.• Please unplug the device during thunderstorm or when the device is not used for a long time.This avoids damage by surge voltage.• Do not plug into a power strip or extension cord; otherwise overloading may occur. Overloading may lead to fire or electric shock.• Do not put any foreign object into the notch on the casing of monitor; otherwise parts might be shorted and fire or electric shock may occur. Do not spray liquid onto the monitor.• Do not repair the monitor by yourself. You might be exposed to dangerous voltage andother risks if opening or removing the casing. All repairs must be performed by a qualifiedmaintenance technician.• To ensure normal operation, the monitor can only be used with certified computer products.The voltage of the socket equipped with the computer must be between100 and 240V AC(minimum 5A).• The socket should be installed near this device and easily accessible.Special precautions for LCD monitorThe followings are normal for the LCD monitor, not faults.Notes• The monitor might blink when it is used for the first time because of LED. Please turn off and turn on the power switch and check if blinking stops.• The brightness of monitor might be uneven, depending on the wallpaper.• The effective pixel of LCD monitor is 99.99% (or higher) and 0.01% (or even lower) of the pixels might be defective. For example, the pixel might be missing or remains lit.• When the monitor shows the same image for a long time, the afterimage of the previous image might remain after switching to a new image due to the properties of LCD monitor. However, the monitor will gradually become normal.• If the monitor turns black, blinks or doesn't light up, please contact a dealer or repair center for part replacement. Do not repair the monitor by yourself!BEFORE YOU OPERATE THE MONITOR Features• 709mm (28”) TFT LCD color monitor• Clear display• Recommended resolution: 1920 x 1080@60Hz (VGA), 3840 x 2160@60Hz (HDMI2.0/ DP, graphics card support required)Package contentsThis product package includes the following objects:1. LCD monitor2. User manual3. Power cord4. HDMI wire5. BaseInstallation instructionInstallation:1. Open the package, take out the LCD monitor and lay the monitor flat on a table.2. Assemble the LCD monitor and base as shown. Tighten the screw clockwise.Disassembly:1. Lay the LCD monitor flat on a table as shown:2. Loose the screw counterclockwise and remove the base.Cable connectionSignal cable• Signal cable connection: Insert a 15-pin signal cable into the back of monitor and the VGA port of computer.• HDMI cable connection: Insert a 19-pin HDMI cable into the back of monitor and the HDMI port of computer.• DP cable connection: Insert a 20-pin cable into the back of monitor and the DP port ofcomputer.Power cord1. Be sure to use the power cord complying with local specifications.2. Connect the power cord with the AC port of adapter and socket matching the LCD monitor.Connect the DC cable of adapter with the DC plug of LCD monitor. Connect the AC power cable to the power socket or the socket of the computer, depending on the type of power cord that comes with the LCD monitor.Warning:The AC socket is not grounded (not the three-pin type). Please install a proper earthing adapter (not included).1Power In2HDMI In3DP In4D-Sub In5Audio In6Phone OutAdjusting the viewing angle• For the best view, it is recommended that you stare at the front of the screen and adjust the monitor angle for your preference.• Hold the base tight when adjusting the monitor angle to avoid pushing down the monitor.•Notes• Do not touch the LCD screen when adjusting the angle; otherwise the LCD monitor might be damaged or broken.• When adjusting the angle, make sure that your finger or hand is not pinched by the monitor.OPERATING INSTRUCTIONSGeneral operating instructionsPress the power button to turn on or off the monitor. Other control buttons are on the side of the monitor. Adjust the image for your preference by changing these settings.• Connect the power cable.• Insert the video cable for the monitor into the video card.External control buttons1Power button2Menu/Enter3+ / Volume4- / Eco Mode5Auto adjustment/Signal source/ExitFront panel control• Power button:Press it to turn on or off the monitor.• Power indicator:Blue - "Power on" modeOrange - "Standby" modeIndicator off - "Power off" mode• Menu / Enter:Turn on the OSD menu or check the function adjustment. Exit the OSD menu when entering the brightness/contrast OSD status.• + / Volume:Press a hot key to turn on the volume control. Press "-" to adjust settings. Press the "Menu" button to confirm and exit the OSD.• - / Eco Mode:Turn on the "Eco Mode"(亮度情景模式) when closing the OSD. Browse and adjust icons when opening the OSD. Adjust a function when activating it.• Auto adjustment button/Signal source/Exit:1. When closing the OSD menu, press the button in 3 seconds to active “Autoadjustment”(自动调整). "Auto adjustment"(自动调整)can be used tooptimize the "H. Position"(水平位置), "V. Position"(垂直位置), "clock"(时钟)and "phase”(相位)(for VGA only).2. Press the button to select the input source from the external signal source.3. When opening the OSD menu, press the button to exit the OSD menu.OSD Locked: To lock the OSD, press the "Menu" button when turning off the monitor. Press the power button to turn on the monitor. To unlock the OSD, press the "Menu" but-ton when turning off the monitor. Press the power button to turn on the monitor.How to adjust settings1. Press the "Menu" button to display the OSD menu.2. Press + or - to browse the entire menu. After highlighting the items you need, press the "Menu" button to open them.3. Press + or - to browse the entire sub-menu. After highlighting the items you need, press the "Menu" button to activate them.4. Press + or - to adjust settings.5. To exit and save, press the "Exit"(退出)button. To adjust other settings, repeat Steps 2-4.LuminanceBrightness Eco ModeStandard5090Contrast EXIT :REMOVE :INPUTAUTO MENUAdjusting the pictureDescription of the functions of LED control buttonPlug and playPlug & Play features of DDC2BThis monitor complies with the "VESA DDC Standard" and it is equipped with VESA DDC2B capabilities. This monitor notifies the host system of its information on identification and display function, depending on the DDC level.DDC2B is a two-way data channel based on I²C protocol. The host can request the EDID information through the DDC2B channel.If no image input signal is available, the function of this monitor will not be available. The image input signal must be available for normal operation of the monitor.This monitor complies with the "ECO" standard governed by VESA and NUTEK. The design of this function is to conserve electricity by reducing power consumption when the image input signal doesn't exist. If no image input signal is available, this function switches to "Off" mode automatically based on the setting of delay time. This helps reduces the power consumption of monitor. After the image input signal is recovered, the power is resumed and the image appears on the screen again. The image looks like "screen saver" (except when the monitor is turned off). Press a key on the keyboard or click mouse to return to the screen.TECHNICAL SUPPORT (FAQ)No signal • Please check the connection of the signal cable. If the connector is loose, please fasten the screw on the connector.• Please check if the pin of the signal cable is broken.The input signal is not supported.The display mode setting of the computer is wrong. Please carry out settings according to page 16 "Factory presetting table".*"Clock" manages the number of pixels scanned by a horizontal scanning line. If the frequency is wrong, vertical ripples appear on the screen and the image width would be wrong.*"Phase" is used to adjust the phase of signal of pixel frequency. Horizontal noise appears on brighter images if the phase calibration is wrong.APPENDIX SpecificationsLCD panel Drive system28” TFT color LCD monitor Size709 mm diagonal lines Pixel pitch0.16mm (H) × 0.16mm (V)Input Video signalRGB analog signals (VGA)Digital signals (HDMI2.0/DP) Horizontal frequen-cy30KHz – 99KHz (VGA),30KHz – 160KHz (HDMI2.0/DP) Vertical frequency50-75Hz (VGA), 23-80Hz (HDMI2.0/DP)Screen color 1.07 billion colorsDot frequency210MHz (VGA), 600MHz (HDMI2.0/DP)Highest resolution 1920 x 1080@60Hz(VGA),3840 x 2160@60Hz (HDMI2.0/DP, graphics card support required)Plug & Play VESA DDC2B™Power con-sumption "Boot" mode≤70W "Standby" mode≤0.5W "Shutdown" mode≤0.5WInput connector D-SUB (15-pin) HDMI (19-pin) DP (20-pin)Monitor size Horizontal: 620.93 mm Vertical: 341.28 mmPower Supply100-240V ~, 1.5A, 50/60HzOperating environment conditions Operating temperature: 0° to 40°C Storage temperature: -20° to 60°C Operating humidity: 5% to 85%Dimension659.7 (W) x 390.9 (H) x 49.3 (D) mm Weight (net weight): 5.6 kgExternal con-trol buttons:SwitchPower buttonMenu/Enter+ / Volume- / Eco Mode"Auto adjustment" button / Exit / Signal source Function buttonBrightnessImage SetupColor Temp.OSD SetupOtherSafety standard CCC,CE,FCCFactory presetting tableConnector pin assignmentColor display signal cable (19-pin)Q41G28M108301A。
艺卓flexscan s2203w color LCD user manual说明书
2-10 设定调整菜单显示......................... 19 ● 若要更新菜单设置 [ 菜单大小 / 菜单位置 / 菜单关闭计时器 / 透明度 ].................. 19
第 1 章 功能和概述........................... 4
2-11 设定方向................................. 20 ● 设定调整菜单的方向 [ 方向 ]................ 20
舒适地使用显示器
• 屏幕极暗或极亮可能会影响您的视力。请根据环境调节显示器的亮度。 • 长时间盯着显示器会使眼睛疲劳。每隔一小时应休息十分钟。
目录
有关此显示器的注意事项.......................... 1 目录......................................... 3
2-4 调节音量 [ 音量 ].......................... 17
2-5 在省电模式下关闭音频输出 [ 节能 ]......... 17
2-6 设定打开 / 关闭自动亮度调节功能 [Auto EcoView]........................... 18
3-1 将两台 PC 连接至显示器.................... 23 ● 切换输入信号............................. 23 ● 设定输入信号选择 [ 信号输入 ]............. 24
3-2 调节 DVI 输入调整 [DVI 输入调整 ]........... 24
第 4 章 疑难解答............................ 25
夏普液晶电视中文说明书
使用 HDMI 输出设备时的设定................................................. 36 选择输入源和信号类型....................................................... 37
选择输入源......................................................... 37 选择输入信号类型................................................... 37 输入标签................................................................... 38 HDMI/电脑输入跳跃......................................................... 38 彩色制式设置............................................................... 38
在打开电源之前.............................................................. 9 连接外部设备............................................................... 10
连接录影机、游戏机或摄录机......................................... 10 连接 DVD 影碟机.................................................... 10 连接数码电视机解码器 ( 机顶盒 )...................................... 11 连接电脑........................................................... 11 使用数码音频输出................................................... 11 装入电池................................................................... 12 使用遥控器................................................................. 12 关于遥控器的注意事项............................................... 12 打开或关闭电视机........................................................... 13 打开电源........................................................... 13 关闭电源........................................................... 13 选项表操作................................................................. 14 什么是选项表?..................................................... 14 基本的选项表操作................................................... 14 关于引导显示....................................................... 14 电视 / 影音输入模式选项表中的项目................................... 15 电脑输入模式选项表中的项目......................................... 16
LG 32UL750 32BL75U LED LCD显示器用户手册说明书
* L G LED Monitor applies LCD screen with LED backlights.Please read this manual carefully before operating your set andretain it for future reference.32UL75032BL75UCopyright © 2018 LG Electronics Inc. All Rights Reserved.2LICENSEEach model has different licenses. Visit for more information on the license.The terms HDMI and HDMI High-Definition Multimedia Interface,and the HDMI Logo are trademarks or registered trademarks ofHDMI Licensing Administrator, Inc. in the United States and othercountries.The SuperSpeed USB Trident logo is a registered trademark of USBImplementers Forum, Inc.VESA, VESA logo, DisplayPort compliance logo and DisplayPortcompliance logo for dual-mode source devices are all registeredtrademarks of the Video Electronics Standards Association.*TABLE OF CONTENTSLICENSE (2)OPEN SOURCE SOFTWARE NOTICEINFORMATION (3)ASSEMBLING AND PREPARING (3)USING THE MONITOR (8)USER SETTINGS (10)TROUBLESHOOTING (21)PRODUCT SPECIFICATION (23)OPEN SOURCE SOFTWARE NOTICE INFORMA-TIONTo obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit .In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to ******************. This offer is valid for a period of three years after our last shipment of this product. This offer is valid to anyone in receipt of this information.ASSEMBLING AND PREPARINGCAUTION•Always use genuine LG components to ensure safety and product performance.•The product warranty will not cover damage or injury caused by the use of unauthorized components.•It is recommended to use the supplied components.•If you use generic cables not certified by LG, the screen may not display or there may be image problems.•Illustrations in this document represent typical procedures, so they may look different from the actual product.•Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product. (Doing so may damage the product.)•Applying excessive force when tightening screws may cause damage to the monitor. Damage caused in this way will not be covered by the product warranty.•Do not carry the monitor upside down by just holding the base. This may cause the monitor to fall off the stand and could result in personal injury.•When lifting or moving the monitor, do not touch the monitor screen. The force applied to the monitor screen may cause damage to it.•For wave pattern on appearance, unlike the general method of coating, it’s applied to added glittering material in raw material.With no peeled-off appearance, it has good durability. Please use it with confidence because there is no problem in using the product at all.NOTE•The components may look different from those illustrated here.•Without prior notice, all product information and specifications contained in this manual are subject to changeto improve the performance of the product.•To purchase optional accessories, visit an electronics store or an online shopping site, or contact the retailerfrom which you purchased the product.•The power cord provided may differ depending upon the region.Supported Drivers and Software).34How to Use the Joystick ButtonYou can easily control the functions of the monitor by pressing the joystick button or moving it left/right/up/down with your finger.Basic FunctionsNOTE•The joystick button is located at the bottom of the monitor.Moving and Lifting the MonitorWhen moving or lifting the monitor, follow these instructions to prevent the monitor from being scratched or damaged and to ensure safe transportation, regardless of its shape or size.•Place the monitor in the original box or packing material before attempting to move it. •Before moving or lifting the monitor, disconnect the power cord and all other cables. •Hold the bottom and side of the monitor frame firmly. Do not hold the panel itself.•When holding the monitor, the screen should face away from you to prevent it from being scratched. •When transporting the monitor, do not expose the monitor to shock or excessive vibration.•When moving the monitor, keep it upright and never turn the monitor on its side or tilt it sideways.CAUTION•Avoid touching the monitor screen as much as possible.-This may result in damage to the screen or some of the pixels used to create images.•If you use the monitor panel without the stand base, its joystick button may cause the monitor to become unstable and fall, resulting in damage to the monitor or human injury. In addition, this may cause the joystick button to malfunction.5ENGLISHInstalling on a Table•Lift the monitor and place it on the table in an upright position. Place the monitor at least 100 mm (3.94 inches) away from the wall to ensure sufficient ventilation.CAUTION•Unplug the power cord before moving or installing the monitor. There is risk of electric shock.•Make sure to use the power cord that is provided in the product package and connect it to a grounded power outlet.•If you need another power cord, please contact your local dealer or the nearest retail store.Adjusting the Stand Height1 Place the monitor mounted on the stand base in an upright position.2 Handle the monitor with both hands for safety.Max 110.0 mm (4.3 inches)WARNING•Adjusting the Angle1 2 experience. WARNING•To avoid injury to the fingers when adjusting the screen, do not hold the lower part of the monitor’s frame as illustrated below.•Be careful not to touch or press the screen area when adjusting the angle of the monitor.6Using the Kensington LockThe connector for the Kensington security system is located at the bottom of the monitor.For more information on installation and usage, refer to the Kensington lock owner’s manual or visit the website at .Connect the monitor to a table using the Kensington security system cable.NOTE•Installing the Wall Mount PlateThis monitor meets the specifications for the wall mount plate or other compatible devices. NOTE•The wall mount plate is sold separately.•For more information on installation, refer to the wall mount plate’s installation guide.•Be careful not to apply too much force while mounting the wall mount plate as it may cause damage to the screen.•Remove the stand before installing the monitor on a wall mount by performing the stand attachment in reverse.Installing on the WallInstall the monitor at least 100 mm (3.94 inches) away from the wall and leave about 100 mm (3.94 inches) of space at each side of the monitor to ensure sufficient ventilation. Detailed installation instructions can be obtained from your local retail store. Alternatively, please refer to the manual for how to install and set up a tilting wall mounting bracket.7CAUTION•Unplug the power cord before moving or installing the monitor to avoid electric shock.•Installing the monitor on the ceiling or on a slanted wall may result in the monitor falling off, which could lead to injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel.•Applying excessive force when tightening screws may cause damage to the monitor. Damage caused in this way will not be covered by the product warranty.•Use the wall mounting bracket and screws that conform to VESA standards. Damage caused by the use or misuse of inappropriate components will not be covered by the product warranty.•When measured from the back of the monitor, the length of each installed screw must be 8 mm (0.3 inches) or less.To install the monitor to a wall, attach a wall mounting bracket (optional) to the back of the monitor.Make sure that the wall mounting bracket is securely fixed to the monitor and to the wall.Wall Mount (mm)100 x 100Standard screw M4 x L10Number of screws4Wall Mount Plate (Optional)LSW 149NOTE•A non-VESA standard screw may damage the product and cause the monitor to fall. LG Electronics is not liable for any accidents relating to the use of non-standard screws.•The wall mount kit includes the installation guide and all necessary parts.•The wall mounting bracket is optional. You can obtain optional accessories from your local dealer.•The length of the screw may differ for each wall mounting bracket. If you use screws longer than the standard length, it may damage the inside of the product.•For more information, please refer to the user manual for the wall mounting bracket.USING THE MONITOR•Illustrations in this manual may differ from the actual product.Press the joystick button, go to [Settings] [Input], and then select the input option.CAUTION•Do not press the screen for a prolonged time. This may cause image distortion.•Do not display a still image on the screen for a prolonged time. This may cause image retention. Use a PC screensaver if possible.•When connecting the power cord to the outlet, use a grounded (3-hole) power strip or a grounded power outlet.•The monitor may flicker when turned on in an area where the temperature is low. This is normal.•Sometimes red, green, or blue spots may appear on the screen. This is normal. Connecting to a PC•This monitor supports the *Plug and Play feature.* Plug and Play: A feature that allows you to add a device to your computer without having to reconfigure anything or install any manual drivers.HDMI ConnectionTransmits digital video and audio signals from your PC to the monitor.CAUTION•Using a DVI to HDMI / DP (DisplayPort) to HDMI cable may cause compatibility issues.•Use a certified cable with the HDMI logo attached. If you do not use a certified HDMI cable, the screen may not display or a connection error may occur.•Recommended HDMI cable types-High-Speed HDMI®/TM cable-High-Speed HDMI®/TM cable with Ethernet DisplayPort ConnectionTransmits digital video and audio signals from your PC to the monitor.NOTE•There may be no video or audio output depending on the DP (DisplayPort) version of the PC.•Make sure to use the supplied DisplayPort cable of the product. Otherwise, this may cause the device to malfunction.•If you are using a Mini DisplayPort output graphics card, use a Mini DP to DP (Mini DisplayPort to DisplayPort) cable or gender that supports DisplayPort1.4. (Sold separately)USB-C connectionTransmits digital video and audio signals from your PC to the monitor.NOTE•PD(Power Delivery) and DP Alternate Mode(DP over USB-C) are supported via USB-C Port. •Features may not work properly depending on the connected device’s specifications and the environment.•USB-C port is not for the Monitor Power source but for a PC power source.Connect Adapter to supply power to the Monitor8Connecting AV DevicesHDMI ConnectionHDMI transmits digital video and audio signals from your AV device to the monitor.NOTE•Using a DVI to HDMI / DP (DisplayPort) to HDMI cable may cause compatibility issues.•Use a certified cable with the HDMI logo attached. If you do not use a certified HDMI cable, the screen may not display or a connection error may occur.•Recommended HDMI cable types-High-Speed HDMI®/TM cable-High-Speed HDMI®/TM cable with EthernetConnecting PeripheralsUSB Device connectionThe USB port on the product functions as a USB hub.NOTE•It is recommended you install all Windows Updates to keep your Windows up-to-date before connecting to the product for use.•Peripheral devices are sold separately.•A keyboard, mouse, or USB device can be connected to the USB port.•The charging speed may vary depending on the device.•To use USB Downstream port of monitor, user must connect Upstream port of monitor to Host PC using USB C-C or USB C-A cable.•When the USB C-C cable is connected between Upstream port of monitor and Host PC, the Downstream port of monitor support USB 2.0 device.•When the USB C-A cable is connected between Upstream port of monitor and Host PC, the Downstream port of monitor support USB 3.0 device.However, Host PC must support USB 3.0 function.CAUTIONCautions When Using a USB Device•A USB device with an automatic recognition program installed, or that uses its own driver, may not be recognized.•Some USB devices may not be supported or may not work properly.•It is recommended to use a USB hub or hard disk drive with power supplied. (If the power supply is not adequate, the USB device may not be recognized properly.)Headphones ConnectionConnect peripherals to the monitor via the headphones port.NOTE•Peripheral devices are sold separately.•Depending on the audio settings of the PC and external device, headphones and speaker functions may be limited.•If you use angled earphones, it may cause a problem with connecting another external device to the monitor.Therefore, it is recommended to use straight earphones.(Recommend)910ENGLISHMain Menu FeaturesMenu Settings1 To view the OSD menu, press the joystick button at the bottom of the monitor and then enter the [Settings].2 Move the joystick up/down and left/right to set the options.3 To return to the upper menu or set other menu items, move the joystick to or pressing () it.4If you want to exit the OSD menu, move the joystick tountil you exit.[Quick Settings][Input][Picture][General]NOTE •: On•: OffQuick SettingsInputPictureNOTE•The [Picture Mode] that can be set depends on the Input signal.[[Picture Mode] on HDR signal]ENGLISHENGLISHGeneralENGLISH21ENGLISHTROUBLESHOOTING2223ENGLISHPRODUCT SPECIFICATIONThe specifications are subject to change without notice.* The power consumption level can be different by operating condition and monitor setting.* The On mode power consumption is measured with ENERGY STAR® test standard.** The On mode power consumption is measured with LGE test standard (Full White pattern , Maximum resolution).*** In case of USB-C input, the power consumption of Sleep Mode may vary depending on the connected device.*** The monitor goes to the Sleep Mode in a couple of minutes(Max 5 minutes).Factory Support Mode (Preset Mode, PC) DisplayPort/ USB-C2425ENGLISHHDMIHDMI Timing (Video)26The model and serial number of the product are located on the back and on one side of the product. Record them below in case you ever need service.Model Serial No.Supplier’s Declaration of ConformityTrade Name LGResponsible Party LG Electronics USA, Inc.Address 1000 Sylvan Ave Englewood Cliffs, NJ 07632Telephone (201)266-2215As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.ENERGY STAR is a set of power-saving guidelines issued by the U.S.Environmental Protection Agency(EPA).Refer to ENERGY for more information on the ENERGY STAR program.。
TFT LCD 0.96英寸指南说明书
Instruction ManualOverviewAn IPS, full colour TFT module, offering 80 degree viewing angles allround, with a 500nit backlight. It is a transmissive type display operating in the normally black mode.This TFT LCD has a 0.96-inch diagonally measured active display area with 80 x 160 dot (80 horizontal by 160 vertical pixel) resolution. Each pixel is divided into Red, Green, Blue dots which are arranged in vertical stripes.Technical Specificationsz Size: 0.96 inchz Dot Matrix: 80 x RGB x 160(TFT) dotsz Module dimension: 13.5(W) x 27.95(H) x 3.00(D) mmz Active area: 10.8 x 21.696 mmz Dot pitch: 0.135 x 0.1356 mmz LCD type: TFT, Normally black, Transmissivez Viewing Angle: 80/80/80/80z Aspect Ratio: 1:2z IC: ST7735Sz Backlight Type: LED,Normally Whitez With /Without TP: Without TPz Surface: Glare*Colour tone slight changed by temperature and driving voltage.InterfacePin DefinitionTechnical DrawingAbsolute Maximum Ratings1. Temp. ≤60˚C, 90% RH MAX. Temp.>60˚C, Absolute humidity shall be less than 90% RH at 60˚C.Electrical CharacteristicsOperating conditions:Note 1 : There are 1 Groups LEDNote 2 : Ta = 25 ˚CNote 3 : Brightness to be decreased to 50% of the initial valueNote 4 : The single LED lamp caseData Colour Coding3-Wire SPI Mode: RGB 5-6-5-bit Input, 65K-Colours, 3AH=“05h”Look-up table for 65k colour mapping (16 bits to 18 bits) Note 1: Pixel data with the 16-bit colour depth informationNote 2: The most significant bits are: Rx4, Gx5 and Bx4Note 3: The least significant bits are: Rx0, Gx0 and Bx04-Wire SPI Mode: RGB 5-6-5-bit Input, 65K-Colours, 3AH=“05h”Look-up table for 65k colour mapping (16 bits to 18 bits) Note 1. Pixel data with the 16-bit colour depth informationNote 2. The most significant bits are: Rx4, Gx5 and Bx4Note 3. The least significant bits are: Rx0, Gx0 and Bx0Display Options availableTFT display as a stand-alone itemDisplay on pcb with mountingOptical CharacteristicsTa=25±2˚CNote 1: Definition of viewing angle rangeNote 2: Test equipment setup:After stabilizing and leaving the panel alone at a driven temperature for 10 minutes, the measurement should be executed. Measurement should be executed in a stable, windless, and dark room. Optical specifications are measured by Topcon BM-7orBM-5 luminance meter 1.0° field of view at a distance of 50cm and normal direction.Note 3: Definition of Response time:The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time, Tr, is the time between photo detector output intensity changed from 90%to 10%.Black(TFT ON)White(TFT OFF)White(TFT OFF)100%90%10%0%DisplayNote 4: Definition of contrast ratio:The contrast ratio is defined as the following expression.Luminance measured when LCD on the “White” state Contrast ratio (CR) = Luminance measured when LCD on the “Black” stateNote 5: White Vi = Vi50 ± 1.5V Black Vi = Vi50 ± 2.0V“±” means that the analog input signal swings in phase with VCOM signal.“±” means that the analog input signal swings out of phase with VCOM signal.The 100% transmission is defined as the transmission of LCD panel when all the input terminals of module are electrically opened.Note 6: Definition of colour chromaticity (CIE 1931)Colour coordinates measured at the center point of LCDNote 7: Measured at the center area of the panel when all the input terminals of LCD panel are electrically opened.ReliabilityContent of Reliability Test (Wide temperature, -20˚C~70˚C)Environmental TestNote1: No dew condensation to be observed.Note2: The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after remove from the test chamber.Note3: The packing have to including into the vibration testing.。
索尼 BRAVIA NX 系列 LCD 电视机说明书
BRAVIA NX Series: NX800 and NX700Model Code KDL-40NX800 KDL-46NX700 KDL-40NX700 LCD Screen Size 40 46 40TV System Digital: DVB-T Digital: DVB-TColour System NTSC 3.58, NTSC 4.43 (AVin only), PAL, PAL60 (AV inonly), SECAMNTSC 3.58, NTSC 4.43 (AV in only), PAL, PAL60(AV in only), SECAMVideo Signal480/60i, 480/60p, 576/50i,576/50p, 720/50p, 720/60p,1080/50i, 1080/60i,1080/24p (HDMI™),1080/50p (HDMI™ /Component), 1080/60p(HDMI™ / Component)480/60i, 480/60p, 576/50i, 576/50p, 720/50p,720/60p, 1080/50i, 1080/60i, 1080/24p (HDMI™),1080/50p (HDMI™ / Component), 1080/60p(HDMI™ / Component)PICTUREDisplay Resolution Full HD 1080 (1920x1080) Full HD 1080 (1920x1080) Backlight Type LED LED Motionflow™ 200Hz 100HzVideo Processing BRAVIA Engine 3™ BRAVIA Engine 3™ Live Colour™ Technology Yes Yes Intelligent Picture Intelligent Picture Intelligent Picture MPEG Noise Reduction Yes Yes24p True Cinema™TechnologyYes YesScreen FormatTV: Full/ Normal/ WideZoom/ ZoomPC: Full 1/ Full 2/ NormalTV: Full/ Normal/ Wide Zoom/ Zoom/ 14:9PC: Full 1/ Full 2/ NormalPicture ModeVivid/ Standard/ Custom/Cinema/ Game-Standard/Game-Original/ Graphics/Sports/ Photo-Vivid/ Photo-Standard/ Photo-Original/Photo-CustomVivid/ Standard/ Custom/ Cinema/ Game-Standard/ Game-Original/ Graphics/ Sports/Photo-Vivid/ Photo-Standard/ Photo-Original/Photo-CustomViewing Angle 178°178°AUDIOSony Original Surround S-Force Front Surround S-Force Front SurroundSound Mode Dynamic/ Standard/ ClearVoiceDynamic/ Standard/ Clear VoiceSurround Effect Cinema/ Music/ Live Sports/GameCinema/ Music/ Live Sports/ GameStereo System NICAM/ A2 NICAM/ A2Audio Power 20W (10W x 2) 20W (10W x 2) EASE OF USE FEATURESBRAVIA Sync Yes YesDLNA Photo (JPEG), Music (MP3,LPCM), Video (MPEG2,AVCHD)Photo (JPEG), Music (MP3, LPCM), Video(MPEG2, AVCHD)Photo MAP Yes Yes Picture Frame Mode Yes Yes PhotoTV HD Yes Yes XMB™ Yes YesOn Screen InstructionManualYes YesOn Screen Clock Yes Yes Sleep Timer Yes YesPAP Yes YesPC Input PIP Yes Yes NETWORK FEATURESBRAVIA Internet Video Yes Yes BRAVIA Internet Widgets Yes YesWi-Fi Wi-Fi Integrated Wi-Fi Integrated ECO FEATURESPC Power Management Yes YesIdle TV Standby Yes Yes Ambient Sensor Yes Yes Power Saving Modes Yes Yes Energy Saving Switch Yes YesProduct, Packaging & Printed Materials--> 70% Recycled Paper--> 70% Recycled PaperTERMINALHDMI™ 4 (2 Side/ 2 Rear) 4 (2 Side/ 2 Rear)USB 2.01 (Side)Photo (JPEG, RAW), Music(MP3), Video (AVC,AVCHD, MPEG4)1 (Side)Photo (JPEG, RAW), Music (MP3), Video (AVC,AVCHD, MPEG4)Ethernet Connection 1 (Rear) 1 (Rear)Component 1 (Side, Composite InputCommon Use)1 (Side, Composite Input Common Use)Composite 2 (1 Side, Component InputCommon Use)/ 1 Rear)2 (1 Side, Component Input Common Use)/ 1Rear)HD 15 PC Input 1 (Side) 1 (Side)Digital Audio Output(s) 1 (Rear) Optical DigitalOutput1 (Rear) Optical Digital OutputAudio Out 1 (Rear) 1 (Rear)Headphone Out 1 (Side) 1 (Side) GENERALDisplay Language English, Simplified Chinese,Arabic, Persian,Vietnamese, Thai, French,RussianEnglish, Simplified Chinese, Arabic, Persian,Vietnamese, Thai, French, RussianStand Swivel Yes YesStand Tilt Range 0°/ 6°Upward Style 0°/ 6°Upward StylePower Requirements (Voltage/ Frequency) AC 110-240V50/60HzAC 110-240V50/60HzPower Consumption (in Operation) 133W129W 109WPower Consumption (in Standby) 0.2W0.23W 0.2WTV Dimension (W x H x D) (mm) Approx. 994x635x64Approx.1127x716x64Approx. 994x641x64TV Dimension (with Stand) (W x H x D) (mm) Approx. 994x669x290Approx.1127x748x320Approx. 994x673x290TV Weight (kg) Approx. 20.1 Approx. 24.0 Approx. 19.2 TV Weight (with Stand) (kg) Approx. 23.8 Approx. 27.8 Approx. 22.6 ACCESSORIESSupplied Remote Control RM-GD011 RM-GD011 Supplied Batteries Type AAA x2 Type AAA x2 Optional Wall-mount Bracket SU-WL700 SU-WL-700 Optional Design Stand SU-40NX1 SU-46NX1 SU-40NX1。
欧普迪TG12864E 128X64 LCD手册
Contents1. Precautions in Use of LCD Module------------------------------------P32. General Specification-------------------------------------------------------P33. Absolute Maximum Ratings----------------------------------------------P34. Electrical Characteristics--------------------------------------------------P45. Backlight Information------------------------------------------------------P46. Optical Characteristics-----------------------------------------------------P57. Interface Description-------------------------------------------------------P68. Contour Drawing & Block Diagram-------------------------------------P79. Application circuit------------------------------------------------------------P810. Timing Characteristics----------------------------------------------------P911. Display Control Instruction--------------------------------------------P10 11.1 Instruction table-----------------------------------------------------P1011.2 Instruction description --------------------------------------------P1012. Reset and Initializing flow chart --------------------------------------P1213. Display Data RAM map ------------------------------------------------P1314. Revision records------------------------------------------------------P141. Precautions in Use of LCD Module(1) Avoid applying excessive shocks to the module or making any alterations or modifications to it.(2) Don’t make extra holes on the printed circuit board, modify its shape or change the components of LCDModule.(3) Don’t disassemble the LCM.(4) Don’t operate it above the absolute maximum rating.(5) Don’t drop, bend or twist LCM.(6) Soldering: only to the I/O terminals.(7) Storage: please storage in anti-static electricity container and clean environment.2. General SpecificationItem Standard Value Unit Number of dots 128X64 Dots DotsOutline dimension 54.0(W)X50.0(H)X9.0MAX.(T) mm View area 43.6(W)X29.0(H) mmActive area 40.92(W)X24.92(H) mmDot size 0.28(W)X0.35(H) mmDot pitch 0.32(W)X0.39(H) mmLCD type STN,Yellow-green,positive,TransflectiveView direction 6 o’clockBacklight Side,Yellow-green LEDDC-DC convertor Built-in3. Absolute Maximum RatingsITEM SYMBOL MIN. TYP. MAX. UNIT Operating Temperature T OP-20 -+70 ℃Storage Temperature T ST-30 -+80 ℃Input Voltage V I0 -V DD V Supply Voltage For Logic V DD0 - 5.5 V Supply Voltage For LCD V DD-V EE0 -10 V4. Electrical CharacteristicsITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT Logic Voltage V DD-V SS- 4.7 5.0 5.2 V Supply Voltage for LCD V DD-V O Ta=25℃--- 8.5 --- V Input High Volt. V IH- 2.0 -V DD V Input Low Volt. V IL--0.3 -0.8 V Output High Volt. V OH I oH=-0.2mA 2.4 -V DD V Output Low Volt. V OL I oL=1.6mA0 -0.4 V Supply Current I DD---- 5.0 --- mA 5. Backlight InformationAbsolute Maximum ratings (Ta=25℃)Item Symbol Conditions Rating Unit Reverse voltage Vr - 5.0 V Reverse Current I r Vr=5.0V 80 uA Absolute maximum forward Current Ifm 120 mA Peak forward current Ifp I msec plus 10% Duty Cycle 160 mA Power dissipation P d350 mW Operating Temperature Range T oper-30~+70 ℃Storage Temperature Range Tst -40~+80 ℃Electrical/Optical Characteristics (Ta=250C,If=10mA)Color Wavelengthλp(nm)Spectral line halfwidthΔλ(nm)OperatingVoltage(V)(±0.15V)ForwardCurrent (mA)Yellow-green --- --- 4.2 836. Optical CharacteristicsITEM SYMBOL CONDITION MIN TYP MAX UNIT View Angle(V)θCR≧2 10 -120 deg.(H)φCR≧2 -45 -45 deg. Contrast Ratio CR -- 5 --Response TimeT rise --200 300 msT fall --150 200 ms7.Interface DescriptionCN1Pin No. Symbol Level Description1 V SS0V Ground2 V DD 5.0V Power supply for Logic3 V O(Variable) Driving voltage for LCD4 RS H/L H:Data L :Instruction5 RW H/L H:Read L:Write6 E H/L Enable signal7~14 DB0~DB7 H/L Data bus. DB7 is used for Busy Flag .15 CS1 H Selection for IC1,active High16 CS2 H Selection for IC2,active High17 /RST L Reset signal, active low18 VEE -10.0V Negative voltage output for LCD driving voltage19 A(LED+) +5.0V Anode of LED Backlight20 K(LED-) 0V Cathode of LED BacklightCN2:21~40 NC --- No connection8. Contour Drawing & Block Diagram9. Application circuitInterfaces with 8080-series MPUInterfaces with 6800-series MPU10. Timing CharacteristicsCharacteristic Symbol Min. Type Max. UnitE cycle t C1000 --nsE high level width t WH450 --nsE low level width t WL450 --nsE rise time t R--25 nsE fall time t F--25 nsAddress set -up time t ASU140 --ns Address hold time t AH10 --ns Data set -up time t DSU200 --ns Data delay time t D--320 ns Data hold time (write) t DHW10 --ns Data hold time (read) t DHR20 --ns11. Display Control InstructionThe display control instructions control the internal state of the LCD module. Instruction is received from MPU to LCD module for the display control. The following table shows various instructions.11.1 Instruction tableInstruction RS RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 FunctionDisplay On/off 0 0 0 0 1 1 1 1 1 DControls the display ON orOFF.The internal statusand the DDRAM data isnot affected.D=0: OFF; D=1: ONSet Address (Y address) 0 0 0 1 Y address (0~63)Sets the Y address at thecolumn address counterSet Page (X address) 0 0 1 0 1 1 1 Page (0~7)Sets the X address at theX address register.Display Start Line 0 0 1 1 Display start line (0~63)Indicates the Display DataRAM displayed at the topof the screen.Status Read 0 1 Busy 0ON/OFFReset 0 0 0 0Reads the internal statusBUSY0: Ready1: In operationON/OFF0: Display ON1: Display OFFRESET0: Normal1: ResetWriteDisplay Data 1 0 Write dataWrites data (DB[0:7]) intothe DDRAM. After writinginstruction, Y address isincriminated by 1automaticallyReadDisplay Data 1 1 Read dataReads data (DB[0:7]) fromdisplay data RAM to thedata bus.11.2 Instruction Description1) Display On/OffThe display data appears when D is 1 and disappears when D is 0.Though the data is not on the screen with D=0, it remains in the display data RAM. Therefore,you can make it appear by changing D=0 into D=1.RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB00 0 0 0 1 1 1 1 1 D2) Set Address (Y Address)Y address (AC0~AC5) of the display data RAM is set in the Y address counter.An address is set by instruction and increased by 1 automatically by read or write operations of display data.RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB00 0 0 1 AC5 AC4 AC3 AC2 AC1 AC03) Set Page (X Address)X address (AC0~AC2) of the display data RAM is set in the X address register.Writing or reading to or from MPU is executed in this specified page until the next page is set.RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB00 0 1 0 1 1 1 AC2 AC1 AC04) Display Start Line (Z Address)Z address (AC0~AC5) of the display data RAM is set in the display start line register and displayed at the top of the screen.When the display duty cycle is 1/64 or others (1/32~1/64), the data of total line number of LCD screen, from the line specified by display start line instruction, is displayed.RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB00 0 1 1 AC5 AC4 AC3 AC2 AC1 AC05) Status ReadRS R/W DB7 DB6 DB5 DB4 DB DB2 DB DB00 1 BUSY 0 ON/OFF RESET 0 0 0 0l BUSYWhen BUSY is 1, the Chip is executing internal operation and no instructions are accepted.When BUSY is 0, the Chip is ready to accept any instructions.l ON/OFFWhen ON/OFF is 1, the display is off.When ON/OFF is 0, the display is on.l RESETWhen RESET is 1, the system is being initialized.In this condition,no instructions except status read can be accepted.When RESET is 0, initializing has finished and the system is in the usual operation condition.6) Write Display DataWrites data (D0~D7) into the display data RAM.After writing, Y address is increased by 1 automatically.RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB01 0 D7 D6 D5 D4 D3 D2 D1 D07) Read Display DataReads data (D0~D7) from the display data RAM.After reading instruction, Y address is increased by 1 automatically.RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB01 1 D7 D6 D5 D4 D3 D2 D1 D012.Reset and Initializing flow chart12.1 ResetThe system can be initialized by setting RSTB terminal at low level when turning power on, receiving instruction from MPU.When RSTB becomes low, following procedure is occurred. — Display off— Display start line register become set by 0. (Z-address 0)While RSTB is low, No instruction except status read can be accepted. Therefore, execute other instructions after making sure that DB4 = 0 (clear RSTB) and DB7 = 0 (ready) by status read instruction. The Conditions of power supply at initial power up are shown as follow.12.2 Initializing flow chartItem Symbol Min Typ Max UnitReset time t RS 1.0 - - uSRise time t R - - 200 nS13. Display Data RAM map14. Revision recordsVersion Ref.pages Revision Items Date A00 All New release 2011.02.15。
LCD Keypad Shield 用户手册说明书
LCD Keypad Shield Users ManualDreamfactory梦工厂LCD Keypad Shield Users ManualTEL:(成都办事处)卫先生159****8530(上海办事处)桑先生137****1234LCD Keypad ShieldA. 注意!在没有认真阅读本说明之前,请勿给模块加电!错误接线将导致模块永久性损坏或烧毁微控制器。
B. 注意!请认真查看引脚功能说明,正确接线!请勿将电源反接,否则将导致模块永久性损坏。
C. 注意!本产品使用电源电压为直流5V,请勿使用超出额定电压的电源!保证电源的稳定,如果出现高压脉冲,可能会导致微控制器永久性损坏。
D. 注意!本产品无防水防潮功能,请在干燥环境下保存或使用!不可将重物堆积在上面。
概 述自从推出DFRduino 控制器以后,有大量客户就抱怨没有LCD 的扩展板可用,如今我们设计了一款带AD 键盘的LCD 扩展板,方便大家使用DFRduino 控制器制作互动或机器人作品。
性能描述1. 工作电源:+5V 2. 工作电流:<20mA3. 工作温度范围 :-10℃~+70℃ 4. 模块尺寸80mm × 57 mm 5. 模块重量:约60g模块模块引脚定义引脚定义Arduino端口功能模拟0 5个功能按键数字4 DB4数字5 DB5数字6 DB6数字7 DB7数字8 RS数字9 EN数字10 背光控制模块的测试模块插到Arduino上,接上USB线,下载以下代码:/*The circuit:* LCD RS pin to digital pin 8* LCD Enable pin to digital pin 9* LCD D4 pin to digital pin 4* LCD D5 pin to digital pin 5* LCD D6 pin to digital pin 6* LCD D7 pin to digital pin 7* LCD BL pin to digital pin 10* KEY pin to analogl pin 0*/#include <LiquidCrystal.h>LiquidCrystal lcd(8, 13, 9, 4, 5, 6, 7);char msgs[5][16] = {"Right Key OK ","Up Key OK ","Down Key OK ","Left Key OK ","Select Key OK" };int adc_key_val[5] ={50, 200, 400, 600, 800 };int NUM_KEYS = 5;int adc_key_in;int key=-1;int oldkey=-1;void setup(){lcd.clear();lcd.begin(16, 2);lcd.setCursor(0,0);lcd.print("ADC key testing");}void loop(){adc_key_in = analogRead(0); // read the value from the sensor key = get_key(adc_key_in); // convert into key pressif (key != oldkey) // if keypress is detected{delay(50); // wait for debounce timeadc_key_in = analogRead(0); // read the value from the sensor key = get_key(adc_key_in); // convert into key pressif (key != oldkey){lcd.setCursor(0, 1);oldkey = key;if (key >=0){lcd.print(msgs[key]);}}}delay(100);}// Convert ADC value to key numberint get_key(unsigned int input){int k;for (k = 0; k < NUM_KEYS; k++){if (input < adc_key_val[k]){return k;}}if (k >= NUM_KEYS)k = -1; // No valid key pressedreturn k;}版本时间备注V1.0 2009年4月15日创建文档Copyright DFRobot。
液晶显示器 说明书
LCD Monitor User ManualGETTING STARTED (1)Introduction (1)Features (1)Unpacking and Checking of the Package Contents (1)Installing the Monitor (2)OPERATING THE MONITOR (3)How to Use the OSD (On Screen Display) (4)Menu Table (5)FOR YOUR SAFETY (6)SPECIAL NOTES ON LCD MONITORS (7)Cleaning (7)Power Management (7)Supported Timing (8)Troubleshooting Procedures (8)CONFORMITY AND COMPLIANCE (9)GETTING STARTEDWARNING: Do not operate the LCD monitor with unspecified power supply. Usage of incorrect voltage will cause malfunction and may cause fire or electric shock.IntroductionBright and sharp images of text and graphics are what you will find with your LCD color monitor. They provide a maximum resolution of 1280x1024 pixels with a flicker-free display at up to 75Hz refresh rate and offer bright, sharp and vibrant color display without the radiation emission and hazards of CRT monitors.Features˙Support SXGA resolution of 1280x1024 pixels with up to 16.2 M colors˙Wide viewing angle support˙Wide tilting angle : - 3 degrees to 20 degrees˙VESA DPMS-compliant power saving: automatically powers down the monitor after a defined period of inactivity.˙Digital Character Smoothing˙Automatic Set-Up˙Ergonomic Design: TCO ’95/’99 Approved˙Windows 95/98/2000/XP Plug & Play Compliant˙Versatile, functional & User friendly OSD˙Plug & Play: Conform to the VESA standards and support DDC1/2B spec. Unpacking and Checking of the Package ContentsBefore unpacking your LCD Monitor, prepare a stable, level, and clean surface near a wall outlet for your LCD Monitor.1. Set the LCD Monitor box in an upright position and open from the top of the boxbefore removing the right/left cushions.2. Remove the back cover from your monitor (pull from the bottom of cover to open)to install your PC system.1VGA Cable AC/DC Adaptor Power Cord Audio Cable User’s manual DVI Cable(Dual Model) Installing the Monitorz DO NOT install the monitor where sudden temperature changes may occur, or in humid, dusty, or smoky areas as it may cause fire, electric shock or damage.z DO NOT place your LCD Monitor near a window as it may be severely damaged if exposed to rain, water, moisture, or sunlight.z MAINTAIN good ventilation; covering of ventilation slots or holes may cause fire.z PLACE the monitor at least 4” (or 10 cm) way from the wallsz SAFE storage temperature of the LCD Monitor is in a range of -20 to +65℉. Connecting the monitor1. Turn off your PC and the LCD Monitor before connecting your LCD monitor to the PC.2. Use VGA cable to connect the VGA connector of the LCD Monitor to the VGA port of thePC system. Make sure the cable head is securely connected. (Option: If your systemis Dual signal model, then use the DVI cable to connect the DVI connector to the DVIport)3. Use Audio cable to connect “Audio in” jack on LCD Monitor and sound card’s “Audio out”jack.4. Plug the DC connector of the adaptor to your monitor’s DC jack.5. Plug the female end of the power cord into the AC adaptor.6. Connect the male end of the power cord into a wall socket.7. Turn on your computer, and then turn on your LCD Monitor.Audio in Connect with Audio cable.VGAconnectorConnect with VGA cable.Power Plug into the AC power adapter.DVI connector (optional) Connect with detachable DVI cableRemark: DVI Cable is for Dual Model use onlyNOTEFor added protection, it is recommendedto use a Surge Protection device plugged between the AC Adapter and theelectrical wall outlet to prevent the effectsof sudden current variations fromreaching the LCD Monitor. Sudden peaksof electricity may cause damage to the Monitor.23OPERATING THE MONITORThe LCD monitor has been preset at the factory with the Timing shown in Appendix to create optimal picture. Users are also able to adjust the picture to the desired brightness and sharpness by following the instructions.Adjusting the Viewing AngleYour LCD Monitor is designed to allow you to adjust it to an optimal viewing angle.ButtonsFunctions1 AUTOAutomatically adjust image Clock, Phase, H-Position, V-Position settings2 e Indicating the cursor movement or OSD manual selection in decremental values3 MENU Pop up OSD Menu or Enter into sub menu4 f Indicating the cursor movement or OSD manual selection in incremental values5 EXITExit OSD Menu and user setting saving6 PowerSwitchPower ON/OFF the monitorNOTEDo not touch the screen while changing the viewing angle. It may damage the screen. Make sure not to catch your fingers while changing the viewing angle.Model AModel B & CHow to Use the OSD (On Screen Display)OSD function allows the user to easily adjust the display to the desired quality. The OSD menu includes a main menu and a sub-menu.Structure of OSD MenusOperating ProcedureUse the buttons on the right side control panel to adjust the OSD1. Power on the LCD monitor.“MENU” button to pop up the OSD menu.2. Press“e” or “ f” button to select menu item.3. Press“MENU” button to select sub menu.4. Press“e” or “ f” button to select sub menu item.5. Press-If User setting does not appear then go to step 9.6. Press“MENU” button to the user setting.“e” or “ f” button to select or adjust.7. Press“EXIT” button when finished adjusting and accept the user setting.8. PressOR9. Press “MENU” button to process this item then accept or reject the setting.45Menu TableMain MenuSub MenuFunction Name Situation/OptionAll Reset Recall the all factory default settings.Auto AdjustAutomatically adjust image Clock, Phase, H-Position,V-Position settings Reset Color Recall the color default settingsReset OSD Recall the OSD default settingsAnalog Select Analog signal input (Dual model use only)Digital Select Digital signal input (Dual model use only)MuteDisable or enable soundVolume Volume control Brightness Adjust BrightnessContrast Adjust ContrastRGB AdjustAdjust Red, Green, Blue colorColor Temperature Change the color intensity of the temperatureselectedClock Adjust To correct flickering text or lines.Phase Adjust To correct flickering text or lines.H-PositionAdjust screen horizontal position.V-Position Adjust screen vertical position.OSD Time Out Set the length of time an OSD screen is displayedOSD Position Allow you to move the OSD Menu on the screen Accept And Exit User setting is saved and exitReject And Exit User setting isn’t saved and exitFOR YOUR SAFETYW ARNINGALWLAYS OPERATE UNDER SPECIFIED POWER SUPPLYUsage of incorrect voltage will cause malfunction and may cause fire or electric shock.PROTECT and CORRECTLY USE THE CABLEDo not pull or bend the power cable and signal cable or place the monitor or any heavy objects on the cables. If the cables are damaged, they may cause fire or electric shock.IMMEDIATELY STOP OPERATING THE MONITOR WHEN YOU DETECT ANY ABNORMAL OCCURENCEIf you notice any abnormal phenomenon such as strange noise, smoke or smells, unplug the monitor and contact your dealer or the nearest service center immediately.DO NOT REMOVE THE CABINETRemoving the cabinet may expose you to the danger of fire or electric shock.DO NOT PUT ANY FOREIGN OBJECT INSIDE THE MONITORIt may cause fire, electric shock or damage when operating the monitor with foreign objects inside. DO NOT USE THE MONITOR NEAR WATEROperating the monitor in close proximity to water where the water may be spilt or splashed onto the monitor may cause fire or electric shock.BAD WEATHER CONDITIONSIt is advisable not to operate the monitor during heavy thunderstorms as intermittent breaks in power may cause malfunction. Do not touch the plug under these circumstances as it may cause electric shock.C AUTIONDISCONNECT CABLES WHEN MOVING THE MONITORWhen moving the monitor, always turn off the switch, unplug the monitor, and disconnect the signal cable. If the cables are not properly disconnected when moving the monitor, it may cause fire or electric shock.DO NOT TOUCH THE PLUG WITH WET HANDSPulling or inserting the plug with wet hands may cause electric shock.HOLD THE PLUG WHEN DISCONNECTINGTo disconnect the power cable or signal cable, always pull the cable by the plug. Never pull on the cable as this may cause fire or electric shock.O THERSERGONOMICS RECOMMENDATIONSDo not operate the monitor in a dark room or against a bright background. For optimal viewing comfort, the monitor should be just below eye level and 30-60 cm (16-24 inches) away from your eyes. When using the monitor over a prolonged period of time, a ten-minute-break per hour is recommended.6SPECIAL NOTES ON LCD MONITORSThe following are normal with LCD monitors and do not indicate a problem.z When first turning on the LCD monitor, if the picture does not fit in the display area, it is because of the type of computer that is used. In such case, adjust the picture position to its correct position.(See Operating the Monitor)z The screen may flicker during initial use. Turn off the power switch and then turn it on again the flickering should disappear.z Users may notice a little uneven brightness on the screen depending on the desktop pattern they use. It is normal for LCD monitors to show such uneven brightness.z Due to the nature of the LCD screen, switching of images after a prolonged period of time of displaying the same image, the image from the previous screen may remain. In such case, the screen is recovered slowly by changing the image or turning off the power switch for hours.z If the screen becomes dark, flickers, or does not light-up, contact your dealer or the nearest service center for a backlight replacement. Do not attempt to replace it yourself.z If you need to return your unit for service and the original packaging was discarded, please contact your dealer or the nearest service center for advice or replacement of packaging. CleaningW ARNINGz If you dropped any material or liquid such as water onto the monitor when cleaning, unplug the power cable immediately and contact your dealer or the nearest service center. Always make sure your hands are dry when unplugging the power cable.C AUTIONz For safety reasons, turn-off the power switch and unplug the monitor before cleaning.z Do not scratch or rub the screen with a hard object.z Never use any of the following solvents on the LCD monitor. Such harsh chemicals may cause damage to the cabinet and the LCD screen.Thinner Spray-type cleaner Benzene Wax Abrasive cleaner Acid or Alkaline solventz Rubbing the cabinet with products made of rubber or plastic for a long period of time may cause degeneration or loss of paint on the cabinet.Cabinetz Remove dirt with a lightly moistened cloth and a mild solvent detergent. Then wipe the cabinet with a soft dry cloth.LCDz Periodic cleaning with a soft dry cloth is recommended.z Do not use tissue to clean the screen. It may damage the LCD screen.Power ManagementThe LCD Monitor complies with the VESA DPMS (version 1.0p) power management proposal. The VESA DPMS proposal provides four phases of power saving modes by detecting the horizontal or vertical sync signal.Item DPMS Mode Display PowerLEDPowerConsumptionRecoveryTimeH-sync V-sync1 On NormalGreenNormal --- On On2 Stand By No Display Amber ≦ 5W3 sec < 10 KHz On3 SuspendNoDisplayAmber ≦ 5W 3 sec On < 10 Hz4 Off No Display Amber ≦ 5W 3 sec <10KHz<10Hz78Supported TimingAnalogDisplay Mode Horizontal Frequency Vertical Frequency31.5 KHz 60 Hz VGA 640 x 48037.5 KHz 75 Hz 720 x 40031.5 KHz 70.1 Hz 35.2 KHz 56.3 Hz 37.9 KHz 60.3 Hz 46.9 KHz 75.0 Hz SVGA800 x 60048.1 KHz 72.0 Hz 48.4 KHz 60.0 Hz 56.5 KHz 70.1 Hz 58.1 KHz 72.0 Hz XGA1024 x 76860.0 KHz75.0 Hz 63.98 KHz60.02 Hz VESASXGA1280 x 1024 79.97 KHz75.02 Hz 640 x 48035.0 KHz 66.7 Hz Macintosh VGA832 x 624 49.7 KHz 74.6 Hz MS-DOS640 x 35031.5 KHz 70.1 HzTroubleshooting ProceduresIf the LCD monitor fails to function correctly, please follow the following steps for a possible solution. 1. Perform the adjustments according to Operating the Monitor . 2. Refer to the following items if you cannot find a proper item listed in the Operating the Monitoror if the problem remains.3. If the problem you have experienced is not described below or you cannot correct the problem,stop using the monitor and contact your dealer or the nearest service center for further assistance.PROBLEMCHECK TO SEENo Display.If the power cord is firmly plugged in the socket.If the power switch is turned on.a) Power indicator doesnot light up.If the AC socket is OK. Please check using another piece of equipment. If the blank screen saver is active, touch the keyboard or mouse. Increase the CONTRAST and/or BRIGHTNESS.If the computer is ON.If the signal cable is properly connected.b) Power indicator isgreen.If the signal timing of the computer is within the spec of the monitor.If the monitor is on power management mode, touch the keyboard or the mouse.If the computer is ON.If the signal cable is properly connected.c) Power indicator isamber.If the signal timing of the computer is within the spec.Display is too dark ortoo bright.If the video output level of the computer is within the spec.Display is not in thecenter.If the signal timing of the computer is within the spec.If the power voltage is within the spec.Display is shaking.If the signal timing of the computer is within the spec. If the signal cable is properly connected.If the signal timing of the computer is within the spec.Display is notsynchronized.If the video output level of the computer is within the spec.9Cablenot connected Change Computer Hz Mode Error CONFORMITY AND COMPLIANCEFCC Compliance StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception (this can be determined by turning, the device off and on), you are encouraged to try to correct the interference by one or more of the following measures:*Reorient or relocate the receiving antenna.*Increase the separation between the equipment and the receiver.*Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.*Consult the dealer or an experienced radio/TV technician for help.Caution:To comply with the limits for an FCC Class B computing device, you should use the shielded signal cord and shielded power cord supplied with this unit. The Federal Communication Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Radio Frequency Interference StatementWarning:This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.Canadian Doc NoticeFor Class B Computing DevicesThis digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications.CE MARKING DECLARATION OF CONFROMITYThe LCD monitor complies with the requirements of related European standards, which include: z Emission: EN 55022, EN 61000-3-2, EN-61000-3-3 z Immunity: EN 50082-1z Safety: EN 60950 [Low-Voltage Directive (73/23/EEC)ENERGY STARThis product meets the Energy Star guidelines for energy efficiency.TCO’99Congratulations! You have just purchased a TCO’99 approved and labeled products. Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.。
10.1inch HDMI LCD (B) User Manual
10.1inch HDMI LCD (B)User ManualIntroductin (3)The LCD and Control Board (3)How to Use (4)Holder Assembly (4)Working with PC (4)Hardware Connection (4)Tablet PC Settings (5)Workign with Raspberry Pi (8)OS Preparation (8)Hardware connection (10)Rotation (11)About Brightness of Backlight (13)10.1inch Capacitive Touch Screen LCD, IPS, 1280×800, Supports Multi mini-PCs, Multi Systems, Comes with US plug power adapter.THE LCD AND CONTROL BOARD⚫IPS screen,1280×800 high resolution⚫Capacitive touch control, supports up to ten-points touch⚫When works with Raspberry Pi, supports Raspbian, Ubuntu, single touch, and driver free⚫When work as a computer monitor, supports Windows 10/8.1/8/7, ten-points touch, and driver free⚫Supports Banana Pi, Banana Pro, comes with Lubuntu, Raspbian images⚫Supports BB Black, comes with Angstrom image⚫HDMI interface for displaying, USB interface for touch control⚫Supports 5-level backlight adjustmentHOLDER ASSEMBLYIf you require to assemble holders which are include in package, you can refer to this pages: How to assemble holders for 10.1inch HDMI LCD (B)WORKING WITH PCThis LCD supports Windows 10/8.1/8/7 OS. When working with Windows 10/8.1/8 OS, the touch screen supports multi-touch up to 10 points. For some Window 7 OS, the touch screen supports single touch only.HARDWARE CONNECTION1.Connect the Power Only port of LCD to a 5V2.5A power adapter with a Type A tomicro USB cable2.Connect the Touch port of the LCD to one of the USB ports on your PC3.Connect the HDMI port of the LCD to the HDMI port on your PC with a HDMIcableGenerally, you will see the desktop displayed in LCD as below. In this interface, slightly click the screen can slightly click the screen can perform the left-key mouse action, and long press the screen can perform the right-key mouse action.TABLET PC SETTINGSAs we know, when multiple displays are detected by your PC, the LCD can only be used to control the cursor on main display. So it is proposed to set the touch LCD as the main display. In Windows 10, there is Tablet PC Settings allow you to set touchscreen to control other displays instead of main display. Here we use Waveshare 7inch HDMI LCD (C) as example to show you how to do this setting.1.Connect your touchscreen as Hardware Connection.2.Open Control Panel and search Tablet PC Setting, then open this tool. Note that ifyou didn’t connect touchscreen first, this tool couldn’t be searched.3.C lick button “Setup…” to begin setting4.To this step, you can find there is prompt on your first screen with whitebackground color.5.Press “Enter” on keyboard, this operation work as tell the PC this screen is notthe touchscreen I want to control. Then, you can find that the prompt has turn tothe second display (the one we want the touch controls)6.Touch the center of touchscreen, to set this display as touchscreen. If there areonly two displays, after touch, the setting will finish, and you can find thattouchscreen controls itself now.【Note】This method can be used to make touchscreens control different displays if there are multiple touchscreen connected.WORKIGN WITH RASPBERRY PIOS PREPARATIONFor the Windows OS on PC, the resolution of the LCD is automatically identified. Hence, you do not need to make the relative settings. When working with RaspberryPi, you should set the resolution of the LCD by yourself, or else the LCD screen will not work. For more detail information, please read the following section.At the beginning, you should download the latest image file, RASPBIAN or UBUNTU MATE, from the website: /downloads/.1.Download the image file (zipped) into your PC, and extract it, then you will get afile with the expansion name .img2.Connect a TF card to your PC and format your TF card with the software SDFormatter. Notices: The capability of TF card in used here should be more than 4GB. In this operation, a TF card reader is also required, which should bepurchased separately.3.Start the software Win32DiskImager, and select image file downloaded in the firststep, then, click the button Write to program the system image file.4.When the programming finished, open the config.txt file under the root directoryin the TF card, and add the following lines at the end of the file. Then, save the modification and pop-out the TF card.5.If the statements above do not work properly, replace them with the followinglines:HARDWARE CONNECTION1.Connect the Power Only interface of the LCD to a 5V2.5A power adapter with aType A to micro USB cable (Normally, the LCD will perform screen-clear and self-checking. If there is nothing displayed on the screen, please check whether the LCD screen has been turned on. In case that the screen is ON, please check if the FFC cable is connected properly and in a good contact).2.Connect the HDMI interface of the LCD to the HDMI interface on your RaspberryPi with a HDMI cable3.Connect the Touch interface of the LCD to one of the USB interfaces on your Pi.4.Insert a TF card into the TF card socket on the Raspberry Pi, and then power upthe Pi. Waiting for a while, you may see the following interface. (Now, you can control the back light of the LCD with the back light adjustment button; see the mark 1 shows in the following figure.)ROTATIONDisplay Rotating1.To rotating the display, you can append this statement to the config file2.Reboot the Raspberry PiTouch RotatingNote: To rotate the touch, you can re-compile the kernel as well. There is an example for reference (use 7inch HDMI LCD (C).)⚫Re-Compilation MethodAnother way, you can set the libinput.1.Install libinput2.create an xorg.conf.d folder3.copy file 40-libinput-conf to the folder which we created4.Append a statement to touchscreen part of the file as below:5.save and reboot your PiAfter completing these steps. The LCD could rotate 90 degree both display and touch.【Note】90 degree: Option "CalibrationMatrix" "0 1 0 -1 0 1 0 0 1"180 degree: Option "CalibrationMatrix" "-1 0 1 0 -1 1 0 0 1"270 degree: Option "CalibrationMatrix" "0 -1 1 1 0 0 0 0 1"WORKIGN WITH BB BALCKWe provide and Angstrom image for BB Black, you can download and have a try. Note that you should boot your BB Black from SD card which has been written with test image, and image won’t be updated anymore.⚫Angstrom image for BB BlackWORKIGN WITH BANANAPI/BANANAPI PROWe provide Raspbain and Lubuntu images for BananaPi Pro and BananaPi. Note that they could only support for BananaPi Pro and BananaPi. For ther types of Banana Pi it is unavailable. and image won’t be updated anymore.⚫Raspbian image for BananaPi Pro/BananaPi⚫Lubuntu image for BananaPi Pro/Banana PiThis LCD support Supports 5-level backlight adjustment. You can adjust the brightness manually.After enter desktop, you can touch the virtual button to adjust the brightness.。
BM354S 3.5英寸TFT-LCD屏幕商品说明书
Yellow Video 1Yellow Video 2AUX VideoSource Camera Input1) AUX Video Source operation is controlled by Video Source (Monitor will stay in Stand-By mode unless video source is detected).2) Camera Input functions same as AUX but when Camera Signal is detected it overrides AUX source.VIDEO IN RCA (V1)- AUX Video input (DVD, MP4 etc.) This circuit is secondary andso it will be over written when Camera video is sensed.Black - Chassis GroundBackUp Camera RCA (V2)- Video input for camera (priority) This circuit switches automatically when video is sensed by powering up the reverse cameraImage 3)The Camera may not have sufficient back light for it to capture a clear image. Check to make sure that the vehicle reverse lamps are turning On when the vehicle is shifted into reverse.Image 1)The Camera may be receiving too much light into the lens. This is normally due to a poorly adjusted camera which may be capturing too much direct sunlight. Adjustcamera so that it does not capture too much sunlight.Image 2)The Camera may have excessive amount of dust/ dirt/ grime, using a mild detergent clean the camera lens and retest.Mirror / Standard Image Button (located at the right side lower position) :Press once to select between mirror/standard image.6. T rouble ShootingStand-Alone BackUp Monitor (3.5-inch)Owner's Manual BM354S。
COLOR TFT LCD MONITOR用户手册说明书
COLOR TFT LCD MONITOR User ManualCAUTIONS1.Please use the adapter attached in the accessories.2. Please keep away from strong light while using this product in order toobtain the clearest and the most colorful pictures.3. Please avoid heavy impact or drop onto the ground.4. Please do NOT use chemical solutions to clean this product. Please wipewith a clean soft cloth to maintain the brightness of the surface.5. Please follow the instructions and trouble-shootings to adjust the product.Other improper adjustment may result in damage. Any further adjustment must be performed or conducted by a qualified technician.6. Please unplug the power and remove the battery if long-term no-use, orthunder weather.To ensure the best use of this product, please read this manual carefullybeforehand.Table of Contents1. PRODUCT DESCRIPTION -----------------------------------------2. SETTING MENU -----------------------------------------------------3. ACCESSORIES -------------------------------------------------------4. PARAMETER ---------------------------------------------------------5. TROUBLESHOOTING ----------------------------------------------6.REMARK---------------------------------------------------------------1. PRODUCT DESCRIPTION1.Power: ON/OFF ;switch concurrence battery indicator light (red while standby; green while working)。
光电科技 Optix 系列 LCD 显示器 用户手册说明书
Optix Series LCD MonitorOptix G24C6 (3BA0) Optix G24C6P (3BA0) Optix G27C6 (3CA9) Optix G27C6P (3CA9)ContentsGetting Started (3)Package Contents (3)Installing the Monitor Stand (Optix G24C6 / Optix G27C6) (4)Installing the Monitor Stand (Optix G24C6P / Optix G27C6P) (5)Adjusting the Monitor (6)Monitor Overview (7)Connecting the Monitor to PC (10)OSD Setup (11)Navi Key (11)Hot Key (11)OSD Menus (12)Gaming (12)Professional (14)Image (15)Input Source (16)Navi Key (16)Setting (17)Specifications (18)Preset Display Modes (20)Troubleshooting (21)Safety Instructions (22)Regulatory Notices (23)RevisionV1.0, 2020/102ContentsGetting StartedThis chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.∙Contact your place of purchase or local distributor if any of the items is damaged or missing.∙Package contents may vary by country.3Getting StartedInstalling the Monitor Stand (Optix G24C6 / Optix G27C6)1. Leave the monitor in its protective foam packaging. Align the stand bracket to themonitor groove.2. Tighten the stand bracket with screws.3. Connect the base to the stand and tighten the base screw to secure the base.4. Align the latches to place the stand cover.5. Make sure the stand assembly is properly installed before setting the monitorupright.4Getting StartedInstalling the Monitor Stand (Optix G24C6P / OptixG27C6P)1. Leave the monitor in its protective foam packaging. Align the stand bracket to the monitor groove.2. Tighten the stand bracket with screws.3. Connect the base to the stand and tighten the base screw to secure the base.4. Make sure the stand assembly is properly installed before setting the monitor upright.⚠Important∙Place the monitor on a soft, protected surface to avoid scratching the display panel.∙Do not use any sharp objects on the panel.∙The groove for installing the stand bracket can also be used for wall mount. Please contact your dealer for proper wall mount kit.5Getting Started6Getting StartedAdjusting the Monitor This monitor is designed to maximize your viewing comfort with its adjustment capabilities. ⚠Important ∙Avoid touching the display panel when adjusting the monitor.O 20OOptix G24C6 / Optix G27C6Optix G24C6P / Optix G27C6PO 20OMonitor OverviewOptix G24C6 / Optix G27C67Getting StartedOptix G24C6P / Optix G27C6P8Getting Started9Getting StartedConnecting the Monitor to PC1. Turn off your computer.2. Connect the video cable from the monitor to your computer.3. Assemble the monitor power adapter & power cord. (Figure A)4. Connect the power adapter to the monitor power jack. (Figure B)5. Plug the power cord into the electrical outlet. (Figure C)6. Turn on the monitor. (Figure D)7. Power on the computer and the monitor will auto detect the signal source.10Getting StartedOSD SetupThis chapter provides you with essential information on OSD Setup.⚠ImportantAll information is subject to change without prior notice.Navi KeyThe monitor comes with a Navi Key, a multi-directional control that helps navigate theUp/Down/Left/Right:∙selecting function menus and items∙adjusting function values∙entering into/exiting from function menusPress (OK):∙launching the On-Screen Display (OSD)∙entering submenus∙confirming a selection or settingHot Key∙Users may enter into Game Mode, Screen Assistance, Alarm Clock and Input Source function menus by moving the Navi Key up, down, left or right when the OSD menuis inactive.∙Users may customize their own Hot Keys to enter into different function menus.11OSD SetupOSD Menus12OSD Menus13OSD Menus14OSD Menus15OSD Menus16OSD Menus17OSD Menus20V 18Specifications* Based on CIE1976 test standards.19Specifications20Preset Display ModesTroubleshootingThe power LED is off.• Press the monitor power button again.• Check if the monitor power cable is properly connected.No image.• Check if the computer graphics card is properly installed.• Check if the computer and monitor are connected to electrical outlets and are turned on.• Check if the monitor signal cable is properly connected.• The computer may be in Standby mode. Press any key to activate the monitor. The screen image is not properly sized or centered.• Refer to Preset Display Modes to set the computer to a setting suitable for the monitor to display.No Plug & Play.• Check if the monitor power cable is properly connected.• Check if the monitor signal cable is properly connected.• Check if the computer and graphics card are Plug & Play compatible.The icons, font or screen are fuzzy, blurry or have color problems.• Avoid using any video extension cables.• Adjust brightness and contrast.• Adjust RGB color or tune color temperature.• Check if the monitor signal cable is properly connected.• Check for bent pins on the signal cable connector.The monitor starts flickering or shows waves.• Change the refresh rate to match the capabilities of your monitor.• Update your graphics card drivers.• Keep the monitor away from electrical devices that may cause electromagnetic interference (EMI).21TroubleshootingSafety Instructions∙Read the safety instructions carefully and thoroughly.∙All cautions and warnings on the device or user’s manual should be noted.∙Refer servicing to qualified personnel only.∙Keep the User’s Guide that comes with the package for future reference.∙To prevent fire or shock hazard, keep this device away from humidity and hightemperature.∙Lay this device on a reliable flat surface before setting it up.∙Make sure that the power voltage is within its safety range and has been adjustedproperly to the value of 100~240V before connecting the device to the power outlet.Do not disable the protective earth pin from the plug. The device must be connected to an earthed mains socket-outlet.∙Always disconnect the power cord or switch the wall socket off if the device would be left unused for a certain time to achieve zero energy consumption.∙The ventilator on the device is used for air convection and to prevent the device from overheating. Do not cover the ventilator.∙Do not leave the device in an unconditioned environment with a storage temperature above 60℃ or below -20℃, which may damage the device.∙NOTE: The maximum operating temperature is around 40℃.∙When cleaning the device, be sure to remove the power plug. Use a piece of softcloth rather than industrial chemical to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock.∙Place the power cord in a way that people are unlikely to step on it. Do not placeanything on the power cord.∙Always keep strong magnetic or electrical objects away from the device.∙If any of the following situations arises, get the device checked by service personnel:• The power cord or plug is damaged.• Liquid has penetrated into the device.• The device has been exposed to moisture.• The device does not work well or you can not get it work according to user’smanual.• The device has dropped and damaged.• The device has obvious sign of breakage.∙To prevent the monitor from tipping over, secure the monitor to a desk, wall or fixed object with a anti-tip fastener that helps to properly support the monitor and keep it safe in place.⚠ImportantPlease confirm the power distribution system in the installation site shall provide the circuit breaker rated 120/240V, 20A (maximum).22Safety InstructionsRegulatory NoticesCE ConformityThis device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member Statesrelating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), ErP Directive (2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested and found to comply with the harmonized standards for Information Technology Equipment published under Directives of Official Journal of the European Union.FCC-B Radio Frequency Interference StatementThis equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, maycause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below:∙Reorient or relocate the receiving antenna.∙Increase the separation between the equipment and receiver.∙Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.∙Consult the dealer or an experienced radio/television technician for help. Notice 1The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Notice 2Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.MSI Computer Corp.901 Canada Court, City of Industry, CA 91748, USA(626) 913-082823Regulatory NoticesWEEE StatementUnder the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2012/19/EU, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymoreand manufacturers of covered electronic equipment will be obligated totake back such products at the end of their useful life. Chemical Substances InformationIn compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides the information of chemical substances in products at: https:///html/popup/csr/evmtprtt_pcm.html RoHS StatementJapan JIS C 0950 Material DeclarationA Japanese regulatory requirement, defined by specification JIS C 0950, mandates that manufacturers provide material declarations for certain categories of electronic products offered for sale after July 1, 2006.https:///html/popup/csr/cemm_jp.htmlIndia RoHSThis product complies with the “India E-waste (Management and Handling) Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule. Turkey EEE RegulationConforms to the EEE Regulations of the Republic Of Turkey. Ukraine Restriction of Hazardous SubstancesThe equipment complies with requirements of the Technical Regulation, approved by the Resolution of Cabinet of Ministry of Ukraine as of December 3, 2008 № 1057, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.Vietnam RoHSAs from December 1, 2012, all products manufactured by MSI comply with Circular 30/2011/TT-BCT temporarily regulating the permitted limits for a number of hazardous substances in electronic and electric products.24Regulatory Notices25Regulatory Notices Green Product Features∙Reduced energy consumption during use and stand-by ∙Limited use of substances harmful to the environment and health∙Easily dismantled and recycled ∙Reduced use of natural resources by encouraging recycling ∙Extended product lifetime through easy upgrades ∙Reduced solid waste production through take-back policyEnvironmental Policy∙The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life. ∙Users should contact the local authorized point of collection for recycling and disposing of their end-of-life products. ∙Visit the MSI website and locate a nearby distributor for further recycling information. ∙*******************************************************************disposal, take-back, recycling, and disassembly of MSI products.Warning!Overuse of screens is likely to affect eyesight.Recommendations: 1. Take a 10-minute break for every 30 minutes of screen time. 2. Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day.Copyright and Trademarks Notice Copyright © Micro-Star Int’l Co., Ltd. All rights reserved. The MSI logo used is a registered trademark of Micro-Star Int’l Co., Ltd. All other marks and names mentioned may be trademarks of their respective owners. No warranty as to accuracy or completeness is expressed or implied. MSI reserves the right to make changes to this document without prior notice.Technical Support If a problem arises with your product and no solution can be obtained from the user’s manual, please contact your place of purchase or local distributor. Alternatively,please visit https:///support/ for further guidance.。
8英寸TFT液晶显示器用户手册说明书
TFT LCD COLORMONITOR OPERATION MANUALMode 1Mode 2Mode 3DEAR CUSTOMERSThanks you for purchasing 8”TFT COLOR MONITOR,We hope that you will have the enjoyment of your new mini color TFT LCD.SAFEGUARDS AND PRECAUTIONS1、Please adopt the matched home AC power adapter.2、Do not remove the rear panel of this product. If in need of service, please call aqualified technician.3、Keep away form strong light while using this product so as to obtain theclearest and the most colorful picture.4、Do not seriously impact or drop the product onto the ground.5、Don’t use chemical solutions to clean this TFT LCD set.Please simply wipe witha clean soft cloth to keep the brightness of the surface.CONTENTS1 FEATURE-----------------------------------------------2 CONNECTION-----------------------------------------3 REMOTE CONTROLLER----------------------------4 MENU OPERATION-----------------------------------5 PARAMETER-------------------------------------------6 ACCESSORIES-----------------------------------------7 TROUBLE SHOOTING-------------------------------1、 FEATURE1、Mode 1131. POWER.:ON/OFF2. Indication Light for power supply: Red light means stand by ,Green lightmeans to work.3. PC/A V:VGA , A V switch.4. :Program selection key or using to select function in OSD.5. :Program selection key or using to select function in OSD.6. IR Sensor7. MENU:Display MENU key;8. VOL+: V olume up or using to adjust the number of selected function in OSD.9. VOL-: V olume down or using to adjust the number of selected function inOSD.10. 14P SKS cable input jack11. 12V power input jack12. Folding Bracket13. Touch penMode 2101.-:V olume down key or used to move cursor down in OSD mode2.+:V olume up key or used to move the cursor up in OSD mode3.<:Program selection key or used to select function in OSD mode4.M/E:Display MENU key5.>:Program selection key or used to select function in OSD mode6.A/V:VGA, A V switch7.POWER:ON/OFF8.14P SKS input jack9. DC 12V input jack10. Touch penMode 31011129 8 7 6 5 4 3 2 11. Indication Light for power supply: Red light means stand by ,Green light meansto work.2. VOL+: V olume up key or used to move cursor down in OSD mode3.VOL-: V olume down key or used to move the cursor up in OSD mode4.>: Program selection key or used to select function in OSD mode5.MENU:Display MENU key6.< : Program selection key or used to select function in OSD mode7.A/V: VGA, A V switch8.POWER:ON/OFF9.IR Sensor10.DC 12V input jack11.14P SKS input jack12. Touch pen2. CONNECTIONMode 1Mode 2& Mode 33、REMOTE CONTROLLER: MUTE: To activate OSD menu: V olume up or to adjust the value of setting function: To select function on OSD~: Unit, double-digit, three-Picture, no use.: NO USE4、MENU OPERATIONAfter connected correctly and then Power on, Press “MENU” on the unit or by remote control to show MENUIN A V MODEPress “</>”on the unit or “” on the remote control to select item, eg. ,and it will be highlighted; and then press +/ - of the unit or to adjust the favorite values. It shows current picture format (NTSC&PAL) below the dialog box.BRIGHTNESS: to adjust the luminance of brightnessSATURATION: to adjust the level of saturationTINT: to adjust the hue of imageLANGUAGE:There are 2 languages provided for choice, English and ChineseRESET: you can reset adjustment of the unit when click “YES”OSD H-POSITION ADJUSTMENT: to adjust the OSD move in horizontal directionOSD V-POSITION ADJUSTMENT: to adjust the OSD move in vertical directionOSD DURATION: to adjust the duration of OSD from5-100seconds.picture over-turn to left or rightpicture over-turn to up or downEXIT OSD: select “YES” to exitIN PC MODE:Press “</>”on the unit or “” on the remote control to select item, eg. ,and it will be highlighted with yellow; and then press +/ - of the unit or to adjust the favorite values. It shows picture mode specifications below the dialog box.BRIGHTNESS: to adjust the luminance of brightnessPHASE:to adjust the beginning point and terminal point of imageFREQUENCY: to adjust the frequency range of imageOSD H-POSITION:to adjust the picture position in horizontal directionOSD H-POSITION:to adjust the picture position in vertical directionRESET: you can reset adjustment of the unit when click “YES”COLOR TEMPERATURE:choose color and temperature at first, such as: 65000 K, 75000 K or 93000 K.Only if under “USER” mode, can adjust RED, GREEN and BLUE to meet the color value you need.LANGUAGE:There are 2 languages provided for choice, English and ChineseMISCELLANEOUS:to select to enter next pageAs follows:EXIT OSD: select “YES” to exitOSD H-POSITION ADJUSTMENT: to adjust the OSD move in horizontal directionOSD V-POSITION ADJUSTMENT: to adjust the OSD move in vertical directionOSD DURATION: to adjust the duration of OSD from5-100seconds.OSD AUTO COLOR:If select “YES” it will adjust automatic color system to the bestpicture over-turn to left or rightpicture over-turn to up or down5、PARAMETERTFT LCD SCREENTFT LCD (8 inch)High Resolutions 800*600Average Brightness250 cd/㎡Contrast Ratio 500: 1Mode 1 & Mode 2 4:3Aspect RatioMode 3 16:9Mode 1& Mode 2 140°/120° (H/V)Viewing AngleMode 3 130°/110° (H/V)Color System PAL-4.43 NTSC-3.58Power consumption ≤8.5WAudio Output ≤1.2WInput V oltage DC11-13VMode1 205L×178W×67H mm(Folding)205 L×150 W×210 H mm(Unfolding)Mode 2 220 x166 x37.5 mmDimensionMode 3 196×116×32.5(mm)Mode 1 WITH TOUCH 1024gWITHOUT TOUCH 945gMode2 WITH TOUCH 526gWITHOUT TOUCH 588gWeightMode 3 WITH TOUCH 610gWITHOUT TOUCH 518g6、ACCESSORIES1 2 3 4 5 61 VGA signal cable with 9 holes 1piece2 14P SKS patch cord of A/V cable 1piece3 DC adapter 1piece4 Remote controller 1piece5 Driver disk(Matched with touch function)1piece6 Operation manual 1copy7、TROUBLE SHOOTING7.1、A V MODE7.2、PC MODE① Image excursionAccording to the operation of image station adjustments to adjust: A. Press“<”key, select automatic functionB. Manual adjust as per the operation manual in the menu.C. Select correct refurbish and resolution rate Lose colorPlease check the VGA cable if connect correctly, or what is matter with the VGA cable, if any bend or break in cable, please adopt new VGA cable. No pictureA 、After connecting the power, the indicator light will turn red, thenpress“POWER” button, the unit will work, if the screen display “NO SIGNAL”, that is to say no signal input, at this time, you should open your computer; if the screen display “OVERRANGE”, that is to say signal mode input exceed the range of display, please adjust the refurbish rate of unit.B 、If the green light on the monitor is turned on, the management mode of the power is activated. You may press any key on the computer to activate it. The power of the monitor also has the management mode. If no effect after pressing the keyboard of the PC ,please press “POWER” key on the monitor.C 、If the indicator light is turned off, please check the power connection.Case(condition)Possible causesOnly black and white picture1. The number of “color” function on Video menu is zero.2. The present program have only black and white image. No picture 1. Check power connectin(check the working indicatorlight).2. Check if the A V cable is connected well.The remote controller can not work or insensitive 1. Check battery install method. 2. The battery is used out.3.The signal are influencedNo clear or really image, shaky picturePlease select correct resolution rate, renew the refurbish rate.If any questions, you may be contact with the related dealers.If the whole screen turn light, please check computer refurbish rate is less than 72Hz.Remark:* If happen image interruptive, it is possible that the VGA signal frequency is not matched with normal standard.* It is a normal condition that some bright lines appear on the screen when you are closed the unit.*To ensure a longer use, please make power management function of PC active.。
VG24V系列LCD显示器用户指南说明书
VG24V Series LCD MonitorUser GuideCopyright © 2019 ASUSTeK COMPUTER INC. All Rights Reserved.No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.Table of contentsNotices .........................................................................................................iii Safety information ......................................................................................iv Care & Cleaning (vi)1.1 Welcome! ......................................................................................1-11.2Package contents .........................................................................1-11.3Assembling the monitor ..............................................................1-21.4Connect cables .............................................................................1-31.4.1 Rear of the LCD monitor .................................................1-31.5Monitor introduction ....................................................................1-41.5.1 Using the Controls button ..............................................1-42.1Adjusting the monitor ..................................................................2-12.2Detaching the arm/stand (for VESA wall mount) ......................2-23.1 OSD (On-Screen Display) menu .................................................3-13.1.1 How to reconfigure ..........................................................3-13.1.2 OSD Function Introduction ..............................................3-23.2 Specifications ...............................................................................3-93.3 Troubleshooting (FAQ) ..............................................................3-103.4Supported Timing List ...............................................................3-11NoticesFederal Communications Commission StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:• This device may not cause harmful interference, and• This device must accept any interference received including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference willnot occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Canadian Department of Communications StatementThis digital apparatus does not exceed the Class B limits for radionoise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.This class B digital apparatus complies with Canadian ICES-003.Safety information• Before setting up the monitor, carefully read all the documentation that came with the package.• To prevent fire or shock hazard, never expose the monitor to rain or moisture.• Never try to open the monitor cabinet. The dangerous high voltages inside the monitor may result in serious physical injury.• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.• Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage,contact your dealer immediately.• Slots and openings on the back or top of the cabinet are provided for ventilation. Do not block these slots. Never place this product near or over a radiator or heat source unless proper ventilation is provided.• The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.• Use the appropriate power plug which complies with your local power standard.• Do not overload power strips and extension cords. Overloading can result in fire or electric shock.• Avoid dust, humidity, and temperature extremes. Do not place the monitor in any area where it may become wet. Place the monitor on a stable surface.• Unplug the unit during a lightning storm or if it will not be used for a long period of time. This will protect the monitor from damage due to power surges.• Never push objects or spill liquid of any kind into the slots on the monitor cabinet.• To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles markedbetween 100 ~ 240V AC.• The socket-outlet shall be installed near the equipment and shall be easily accessible• If you encounter technical problems with the monitor, contact a qualified service technician or your retailer.• Provide an earthing connection before the mains plug is connected to the mains.WARNINGUsage of other than specified head- or earphones can result in hearing loss due to excessive sound pressures.Care & Cleaning• Before you lift or reposition your monitor, it is better to disconnect the cables and power cord. Follow the correct lifting techniques whenpositioning the monitor. When lifting or carrying the monitor, grasp the edges of the monitor. Do not lift the display by the stand or the cord.• Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor surface with a lint-free, non-abrasive cloth. Stubborn stainsmay be removed with a cloth dampened with mild cleaner.• Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended for use with the LCD. Never spray cleaner directly on thescreen, as it may drip inside the monitor and cause an electric shock. The following symptoms are normal with the monitor:• The screen may flicker during the initial use due to the nature of the fluorescent light. Turn off the Power Switch and turn it on again tomake sure that the flicker disappears.• You may find slightly uneven brightness on the screen depending on the desktop pattern you use.• When the same image is displayed for hours, an afterimage of the previous screen may remain after switching the image. The screen will recover slowly or you can turn off the Power Switch for hours.• When the screen becomes black or flashes, or cannot work anymore, contact your dealer or service center to fix it. Do not repair the screen by yourself!Conventions used in this guideWARNING: Information to prevent injury to yourself when trying tocomplete a task.CAUTION: Information to prevent damage to the componentswhen trying to complete a task.IMPORTANT: Information that you MUST follow to complete atask.NOTE: Tips and additional information to aid in completing a task.Where to find more informationRefer to the following sources for additional information and for product and software updates.1. ASUS websitesThe ASUS websites worldwide provide updated information on ASUS hardware and software products. Refer to 2. Optional documentationYour product package may include optional documentation that may have been added by your dealer. These documents are not part ofthe standard package.1.1 Welcome!Thank you for purchasing the ASUS® LCD monitor!The latest widescreen LCD monitor from ASUS provides a crisper, broader, and brighter display, plus a host of features that enhance your viewing experience.With these features, you can enjoy the convenience and delightful visual experience that the monitor brings you!1.2 Package contentsCheck your package for the following items:LCD MonitorQuick Start GuideWarranty Card1x Power Cord1x Adapter1x DisplayPort Cable (optional)1x HDMI Cable (optional)• If any of the above items is damaged or missing, contact your retailer immediately.1.3 Assembling the monitorTo assemble the monitor:• While assembling the monitor arm/base, we recommend that you keep the monitor inside its EPS (Expanded Polystyrene) packaging.1. Align the screw hole on the arm with the bundled screw on the base.Then insert the base into the arm.2. Fix the base to the arm by fastening the bundled screw.1.4 Connect cables1.4.1 Rear of the LCD monitor1. Earphone - out Port2. DisplayPort3. HDMI-2 Port4. HDMI-1 Port5. DC-IN Port6. Kensington Lock1. Power Indicator:• 2.Power Button:•Press this button to turn the monitor on/off.3.GameVisual: • Press this hotkey to switch from seven video preset modes (Scenery Mode, Racing Mode, Cinema Mode, RTS/RPG Mode, FPS Mode, sRGB Mode and MOBA Mode) with GameVisual™ Video Intelligence Technology.4.GamePlus Button:• GamePlus : The GamePlus Function provides a toolkit and creates a better gaming environment for users when playing different types of games. Particularly, Crosshair function is specially designed for new gamers or beginners interested in First Person Shooter (FPS) games.To active GamePlus:• Press GamePlus Button to enter the GamePlus main menu.• Activate Crosshair, Timer or FPS Counter or Display Alignment function.• Move the () button up/down to select and press () to confirm the function needed. Press to go off, and exit.• Crosshair/Timer/FPS Counter is movable by pressing 5-way key.5. Close Button:• Exit the OSD menu.6. (5-way) Button:• Turns on the OSD menu. Enacts the selected OSD menu item.• Increases/Decreases values or moves your selection up/down/left/right2.1 Adjusting the monitor• For optimal viewing, we recommend that you look at the full face of the monitor, then adjust the monitor to the angle that is most comfortable for you.• Hold the stand to prevent the monitor from falling when you change its angle.• You can adjust the monitor’s angle from +23˚ to -5˚ and it allows 62˚ swivel adjustment from either left or right. You can also adjust the monitor’s height within +/- 14cm.-5 ~ 232.2 Detaching the arm/stand (for VESA wallmount)The detachable stand of this monitor is specially designed for VESA wall mount.To detach the arm/stand1. Disconnect power and signal cables. Carefully put the monitorfacedown on its EPS packaging.2. Remove the screws covers.3. Remove the four (4) screws securing the arm to the rear of themonitor.4. Detach the stand (arm and base) from the monitor.• The VESA wall mount kit ( 100x100 mm) is purchased separately.• Use only the UL Listed Wall Mount Bracket with minimum weight/load 5.66 kg (Screw size: M4x10 mm).3.1OSD (On-Screen Display) menu 3.1.1How to reconfigure1.Press Central of 5-way to activate the OSD menu.2. Press the ❑ and ☐ buttons to toggle between options in the Menu. As you move from one icon to another, the option name is highlighted.3. To select the highlighted item on the menu press the Center key.4. Press the ❑ and ☐ buttons to select the desired parameter.5. Press the Center key to enter the slide bar and then use the ❑ or ☐ buttons, according to the indicators on the menu, to make your changes.6.Press the ◄/► to move left / right menu.3.1.2 OSD Function Introduction1. GameVisualThis function contains seven sub-functions that you can select for your preference. Each mode has the Reset selection, allowing you tomaintain your setting or return to the preset mode.•Scenery Mode : This is the best choice for scenery photo displaying with GameVisual™ Video Intelligence Technology.•Racing Mode : This is the best choice for racing game playing with GameVisual™ Video Intelligence Technology.•Cinema Mode : This is the best choice for movie watching with GameVisual™ Video Intelligence Technology.• RTS/RPG Mode: This is the best choice for Real-Time Strategy(RTS)/Role-Playing Game(RPG) playing with GameVisual™ Video Intelligence Technology.• FPS Mode: This is the best choice for First Person Shooter game playing with GameVisual™ Video Intelligence Technology.• sRGB Mode : This is the best choice for viewing photos and graphics from PCs.•MOBA Mode : This is the best choice for Multiplayer Online Battle Arena (MOBA) games playing with GameVisual™ Video intelligenceTechnology.•In the Racing Mode, the Saturation, Sharpness, and ASCR functions are not user-configurable.•In the sRGB, the Saturation, Skin Tone, Color Temp., Sharpness, Brightness, Contrast and ASCR functions are not user-configurable.• In the MOBA Mode, the Saturation, Sharpness and ASCR functions are not user-configurable.2. Blue Light FilterAdjust the energy level of blue light emitted from LED backlight.• Level 0: No change.• Level 1~4: The higher the level,the more blue light will be reduced.• When Blue Light Filter is activated,the default settings of Racing Mode will be automatically imported.• Between Level 1 to Level 3, the Brightness function is user-configurable.• Level 4 is optimized setting. It is compliance with TUV Low Blue LightCertification. The Brightness function is not user-configurable.Please refer to the following to alleviate eye strains:• Users should take some time away from the display if working for long hours.It is advised to take short breaks (at least 5 mins) after around 1 hour ofcontinuous working at the computer. Taking short and frequent breaks is moreeffective than a single longer break.• To minimize eye strain and dryness in your eyes, users should rest the eye periodically by focusing on objects that are far away.• Eye exercises can help to reduces eye strain. Repeat these exercises often. If eye strain continues please consult a physician. Eye exercises: (1) Repeatinglook up and down (2) Slowly roll your eyes (3) Move your eyes diagonal.• High energy blue light may lead to eye strain and AMD (Age-Related Macular Degeneration). Blue light Filter to reduce 70% (max.) harmful blue light toavoiding CVS (Computer Vision Syndrome).3. ColorSelect the image color you like from this function.• Brightness: The adjusting range is from 0 to 100.• Contrast: The adjusting range is from 0 to 100.• Saturation: The adjusting range is from 0 to 100.• Color Temp.: Contains three preset color modes (Cool, Normal, Warm) and User Mode.• Skin Tone: Contains three color modes including Reddish, Natural, and Yellowish.• In the User Mode, colors of R (Red), G (Green), and B (Blue) are user-configurable; the adjusting range is from 0 ~ 100.4. ImageYou can adjust the image Sharpness, Trace Free, Aspect Control, VividPixel, ASCR, ELMB, Adaptive-Sync/FreeSync, Shadow Boostfrom this main function.•Sharpness : Adjusts the picture sharpness. The adjusting range is from 0 to 100.•Trace Free: Speeds up the response time by Over Drive technology. The adjusting range is from lower 0 to faster 100.•Aspect Control : Adjusts the aspect ratio to “Full ”, and “4:3”. • VividPixel : ASUS Exclusive Technology that brings lifelike visuals for crystal-clear and detail-oriented enjoyment. The adjusting range is from 0 to 100.• ASCR : Select ON or OFF to enable or disable dynamic contrast ratio function,ASCR is Disabled when ELMB is on.• ELMB : Check to decrease motion blur and minimize ghosting part when on-screen objects are fast moving.• Adaptive-Sync/FreeSync : It can allow a Adaptive-Sync/FreeSync supported graphics source to dynamically adjust display refresh rate based on typical content frame rates for power efficient, virtually stutter free and low-latency display update.•Shadow Boost:Dark color enhancement adjust monitor gamma curve to enrich the dark tones in an image making dark scenes and objects mucheasier be found.• Choose 4:3 to display the picture according to the original aspect ratio of the input source.5. Input SelectSelect the input source from HDMI-1, HDMI-2 or DisplayPort inputsignal.6. System SetupAdjusts the system configuration.•GameVisual Demo Mode : Activate the demo mode for the GameVisual function.• Volume: Adjusts the output volume level.• ECO Mode: Activate the ecology mode for power saving.• OSD Setup: Adjusts the OSD Timeout, DDC/CI, and Transparency of the OSD screen.• Language: Select OSD language. The selections are: English, French, German, Spanish, Italian, Dutch, Russian, Poland, Czech, Croatia, Hungary, Romania, Portugal, Turkey, Simplified Chinese, Traditional Chinese, Japanese, Korean, Persian, Thai and Indonesian.• Key Lock: Disable all key functions. Pressing the down button for more than five seconds to disable key lock function.• Information: Displays the monitor information.• Power Indicator: Turn the power LED indicator on/off.• Power Key Lock: To disable / enable power key.• All Reset: Selects “Yes” to revert all settings to the factory default mode.7. MyFavoriteLoad/Save all settings on the monitor.3.2 Specifications3.3 Troubleshooting (FAQ)3.4 Supported Timing List* H DMI 1.4 does not support 3440x1440-75/100Hz. Use graphics card with HDMI 2.0 to support them.SD/HD Timings List of HDMI / DP input* T he modes not listed in the above tables may not be supported. For optimal resolution, we recommend that you choose a mode listed in the above tables.。
AOC 22B2H LED 背光 LCD 显示器用户手册说明书
LCD Monitor User Manual 22B2HLED backlightSafety (3)National Conventions (3)Power (4)Installation (5)Cleaning (6)Other (7)Setup (8)Contents in Box (8)Setup Base (9)Adjusting Viewing Angle (10)Connecting the Monitor (11)Hotkeys (12)OSD Setting (14)Luminance (15)Image Setup (16)Color Setup (17)Picture Boost (18)OSD Setup (19)Extra (20)Exit (21)LED Indicator (22)i-Menu (23)e-Saver (24)Screen+ (25)Troubleshoot (26)Specification (28)General Specification (28)Preset Display Modes (29)Pin Assignments (30)Plug and Play (31)SafetyNational ConventionsThe following subsections describe notational conventions used in this document.Notes, Cautions, and WarningsThroughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows:NOTE: A NOTE indicates important information that helps you make better use of your computer system.CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.PowerThe monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.Do not overload power strips and extension cords. Overloading can result in fire or electric shock.To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 - 240V ~, Min. 1.5AThe wall socket shall be installed near the equipment and shall be easily accessible.For use only with the attached power adapterManufacturers: TPV ELECTRONICS(FUJIAN)CO.,LTD.Model:ADPC1925EX (19VDC,1.31A)InstallationDo not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the man ufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electric shock. Never spill liquids on the monitor.Do not place the front of the product on the floor.Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence overheating may cause a fire or damage to the monitor.See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or with the stand:Installed with standLeave at lease this spacearound the setCleaningClean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead ofstrong-detergent which will cauterize the product cabinet.When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.Please disconnect the power cord before cleaning the product.OtherIf the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center.Make sure that the ventilating openings are not blocked by a table or curtain.Do not engage the LCD monitor in severe vibration or high impact conditions during operation.Do not knock or drop the monitor during operation or transportation.For display with glossy bezel the user should consider the placement of the display as the bezel may cause disturbing reflections from surrounding light and bright surfaces.SetupContents in BoxMonitorCD Manual Warranty card Base StandAUDIO VGA HDMI AdapterNot all signal cables (VGA, AUDIO, HDMI cables),CD manual will be provided for all countries and regions.Please check with the local dealer or AOC branch office for confirmation.Setup BasePlease setup or remove the base following the steps as below.Please place the monitor on a soft and flat surface to prevent the scratch. Setup:Remove:Adjusting Viewing AngleFor optimal viewing, it is recommended to look at the full face of the monitor, and then adjust the monitor's angle to your own preference.Hold the stand so you will not topple the monitor when you change the monitor's angle.NOTE:Do not adjust the viewing angle over 20 degrees in order to avoid damage.Connecting the MonitorCable Connections In Back of Monitor and Computer:1 HDMI2 Analog (D-Sub 15-Pin VGA cable)3 Earphone out4 PowerTo protect equipment, always turn off the PC and LCD monitor before connecting.1 Connect the power cable to the DC port on the back of the monitor.2 Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to thecomputer's D-Sub port.3 Optional – (Requires a video card with HDMI port) – Connect one end of the HDMI cable to the back of themonitor and connect the other end to the computer’s HDMI port.4 Turn on your monitor and computer.If your monitor displays an image, installation is complete. If it does not display an image, please refer Troubleshooting.Hotkeys1 Source/Auto/Exit2 Clear Vision/3 Image Ratio/Volume/4 Menu/Enter5 PowerMenu/EnterPress to display the OSD or confirm the selection.PowerPress the Power button to turn on/off the monitor.Image Ratio/Volume/When there is no OSD, Press Volume button to active volume adjustment bar, Press or to adjust volume under HDMI signal input. When there is no OSD, press hotkey continuously to change 4:3 or wide image ratio under D-sub signal input. (If the product screen size is 4:3 or input signal resolution is wide format, the hot key is disable to adjust).Auto / Exit / Source hot keyWhen there is no OSD, Press Auto/Source button continuously about 2 second to do auto configure. When the OSD is closed, press Source button will be Source hot key function. Press Source button continuously to select the input source showed in the message bar, press Menu/Enter button to change to the source selected.Clear Vision1. When there is no OSD, Press the “” button to activate Clear Vision.2. Use the “” or “” buttons to select between weak, medium, strong, or off settings. Default setting is always“off”.3. Press and hold “” button for 5 seconds to activate the Clear Vision Demo, and a message of “Clear VisionDemo: on” will be display on the screen for a duration of 5 seconds. Press Menu or Exit button, the message will disappear. Press and hold “” button for 5 seconds again, Clear Vision Demo will be off.Clear Vision function provides the best image viewing experience by converting low resolution and blurry images into clear and vivid images.Clear Vision OffAdjust the Clear Vision WeakMediumStrongClear Vision Demo on or off Disable or Enable DemoOSD SettingBasic and simple instruction on the control keys.1. Press the MENU-button to activate the OSD window.2. Press or to navigate through the functions. Once the desired function is highlighted,press the MENU-button to activate it. If there is a sub-menu, press or to navigate through thesub-menu functions.3. Press or to change the settings of the selected function. Press AUTO to exit. If you want toadjust any other function, repeat steps 2-3.4. OSD Lock Function: To lock the OSD, press and hold the MENU-button while the monitor is off and thenpress power button to turn the monitor on. To un-lock the OSD - press and hold the MENU-button while the monitor is off and then press power button to turn the monitor on.Notes:1. If the product has only one signal input, the item of "Input Select" is disabled.2. If the product screen size is 4:3 or input signal resolution is native resolution, the item of "Image Ratio" isdisabled.3. One of Clear vision, DCR, Color Boost, and Picture Boost functions is activated; the other three functions areturned off accordingly.Luminance1 Press MENU (Menu) to display menu.2 Press or to select (Luminance), and press MENU to enter.3 Press or to select submenu.4 Press or to adjust.5 Press AUTO to exit.Contrast 0-100 Contrast from Digital-register.Brightness 0-100 Backlight AdjustmentEco mode Standard Standard Mode Text Text Mode Internet Internet Mode Game Game Mode Movie Movie Mode Sports Sports Mode Reading Reading ModeGamma Gamma1 Adjust to Gamma 1 Gamma2 Adjust to Gamma 2 Gamma3 Adjust to Gamma 3DCR Off Disable dynamic contrast ratio On Enable dynamic contrast ratio1 Press MENU (Menu) to display menu.2 Press or to select (Image Setup), and press MENU to enter.3 Press or to select submenu.4 Press or to adjust.5 Press AUTO to exit.Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise.Phase 0-100 Adjust Picture Phase to reduce Horizontal-Line noise.Sharpness 0-100 Adjust picture sharpness.H. Position 0-100 Adjust the horizontal position of the picture.V. Position 0-100 Adjust the vertical position of the picture.1 Press MENU (Menu) to display menu.2 Press or to select (Color Setup), and press MENU to enter.3 Press or to select submenu.4 Press or to adjust.5 Press AUTO to exit.Color Temp. Warm Recall Warm Color Temperature from EEPROM. Normal Recall Normal Color Temperature from EEPROM. Cool Recall Cool Color Temperature from EEPROM. sRGB Recall SRGB Color Temperature from EEPROM. User Recall User Color Temperature from EEPROMDCB Mode FullEnhanceON/OFF Disable or Enable Full Enhance Mode. Nature Skin ON/OFF Disable or Enable Nature Skin Mode. Green Field ON/OFF Disable or Enable Green Field Mode. Sky-blue ON/OFF Disable or Enable Sky-blue Mode. AutoDetect ON/OFF Disable or Enable AutoDetect Mode.DCB Demo ON/OFF Disable or Enable Demo.Red 0-100 Red gain from Digital-register. Green 0-100 Green gain from Digital-register. Blue 0-100 Blue gain from Digital-register.LowBlue Mode MultimediaDecrease blue light wave by controlling colortemperatureInternetOfficeReadingOffPicture Boost1 PressMENU (Menu) to display menu. 2 Press or to select(Picture Boost), and press MENU to enter.3 Press or to select submenu.4 Pressorto adjust.5 Press AUTO to exit .Bright Frame ON/OFF Enable/Disable Bright Frame Frame Size 14-100 Adjust the Size of the FrameBrightness 0-100 Brightness Adjustment for Enhance Area Contrast 0-100 Contrast Adjustment for Enhance Area H. position 0-100 Adjust the horizontal position of the Frame V. position0-100Adjust the vertical position of the FrameNote:Adjust the brightness, contrast, and position of the Bright Frame for better viewing experience.OSD Setup1 Press MENU (Menu) to display menu.2 Press or to select (OSD Setup), and press MENU to enter.3 Press or to select submenu.4 Press or to adjust.5 Press AUTO to exit.Language Select the OSD language.Timeout 5-120 Adjust the OSD timeout.V. Position 0-100 Adjust the vertical position of the OSD.H. Position 0-100 Adjust the horizontal position of the OSD.Transparence 0-100 Adjust the OSD.Break Reminder on or off Break reminder if the user continuously work for more than 1hrs.Extra1 Press MENU (Menu) to display menu.2 Press or to select (Extra), and press MENU to enter.3 Press or to select submenu.4 Press or to adjust.5 Press AUTO to exit.Input Select Auto Auto Detect input signalD-SUB Select D-SUB signal source as input HDMI Select HDMI signal Source as inputAuto Config. Yes / No Auto adjust.the picture to default. Off Timer 0-24 hrs Select DC off time.Image Ratio wide or 4:3 Select wide or 4:3 format for display.DDC/CI Yes / No Turn on or off DDC/CI Support. Reset Yes / No Reset the menu to default.Exit1 Press MENU (Menu) to display menu.2 Press or to select (Exit), and press MENU to enter.3 Press AUTO to exit.Exit Exit the main OSDLED IndicatorWelcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation guide.Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below).Please click on "driver/e-Saver/setup.exe" to start installing the e-Saver software, follow the install wizard to complete software installation.Under each of the four PC statuses, you may choose the desired time (in minutes) from the pull-down menu for your monitor to automatically shutdown. The example below illustrated:1) The monitor will never shutdown when the PC is powered on.2) The monitor will automatically shutdown 5 minutes after the PC is powered off.3) The monitor will automatically shutdown 10 minutes after the PC is in sleep/stand-by mode.4) The monitor will automatically shutdown 20 minutes after the screen saver appears.You can click “RESET” to set the e-Saver to its default settings like below.Screen+Welcome to "Screen+" software by AOC. Screen+ software is a desktop screen splitting tool; it splits the desktop into different panels, and each panel displays a different window. You only need to drag the window to a corresponding panel when you want to access it. It supports multiple monitor display to make your task easier. Please follow the installation software to install it.TroubleshootSpecification General SpecificationPreset Display ModesPin Assignments15-Pin Color Display Signal CablePin No. Signal Name Pin No. Signal Name1 Video-Red 9 +5V2 Video-Green 10 Ground3 Video-Blue 11 Ground4 Ground 12 DDC-Serial data5 Detect Cable 13 H-sync6 GND-R 14 V-sync7 GND-G 15 DDC-Serial clock8 GND-B19-Pin Color Display Signal CablePin No. Signal Name Pin No. Signal Name1 TMDS Data 2+ 11 TMDS Clock Shield2 TMDS Data 2 Shield 12 TMDS Clock3 TMDS Data 2 13 CEC4 TMDS Data 1+ 14 Reserved (N.C. on device5 TMDS Data 1Shield 15 SCL6 TMDS Data 1 16 SDA7 TMDS Data 0+ 17 DDC/CEC Ground8 TMDS Data 0 Shield 18 +5V Power9 TMDS Data 0 19 Hot Plug Detect10 TMDS Clock +Plug and PlayPlug & Play DDC2B FeatureThis monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.31。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
带中文字库的128X64液晶模块一、液晶显示模块概述1.液晶显示模块是128×64点阵的汉字图形型液晶显示模块,可显示汉字及图形,内置8192个中文汉字(16X16点阵)、128个字符(8X16点阵)及64X256点阵显示RAM(GDRAM)。
可与CPU直接接口,提供两种界面来连接微处理机:8-位并行及串行两种连接方式。
具有多种功能:光标显示、画面移位、睡眠模式等。
2.外观尺寸:93×70×12.5mm3.视域尺寸:73×39mm外形尺寸图二、模块引脚说明128X64 引脚说明*注释1:如在实际应用中仅使用串口通讯模式,可将PSB接固定低电平,也可以将模块上的J8和“GND”用焊锡短接。
*注释2:模块内部接有上电复位电路,因此在不需要经常复位的场合可将该端悬空。
*注释3:如背光和模块共用一个电源,可以将模块上的JA、JK用焊锡短接。
2.2并行接口管脚号管脚名称电平管脚功能描述1VSS0V电源地2VCC 3.0+5V电源正3V0-对比度(亮度)调整4RS=“H”,表示DB7——DB0为显示数据RS(CS)H/LRS=“L”,表示DB7——DB0为显示指令数据5R/W(SID)H/L R/W=“H”,E=“H”,数据被读到DB7——DB0R/W=“L”,E=“H→L”, DB7——DB0的数据被写到IR或DR6E(SCLK)H/L使能信号7DB0H/L三态数据线8DB1H/L三态数据线9DB2H/L三态数据线10DB3H/L三态数据线11DB4H/L三态数据线12DB5H/L三态数据线13DB6H/L三态数据线14DB7H/L三态数据线15PSB H/L H:8位或4位并口方式,L:串口方式(见注释1)16NC-空脚17/RESET H/L复位端,低电平有效(见注释2)18VOUT-LCD驱动电压输出端19A VDD背光源正端(+5V)(见注释3)20K VSS背光源负端(见注释3)*注释1:如在实际应用中仅使用并口通讯模式,可将PSB接固定高电平,也可以将模块上的J8和“VCC”用焊锡短接。
*注释2:模块内部接有上电复位电路,因此在不需要经常复位的场合可将该端悬空。
*注释3:如背光和模块共用一个电源,可以将模块上的JA、JK用焊锡短接。
二、控制器接口信号说明:1、RS,R/W的配合选择决定控制界面的4种模式:RS R/W功能说明L L MPU写指令到指令暂存器(IR)读出忙标志(BF)及地址记数器(AC)的状L H态H L MPU写入数据到数据暂存器(DR)H H MPU从数据暂存器(DR)中读出数据2、E信号E状态执行动作结果高——>低I/O缓冲——>DR配合/W进行写数据或指令高DR——>I/O缓冲配合R进行读数据或指令低/低——>高无动作BF标志提供内部工作情况.BF=1表示模块在进行内部操作,此时模块不接受外部指● 忙标志:BF令和数据.BF=0时,模块为准备状态,随时可接受外部指令和数据. 利用STATUS RD 指令,可以将BF读到DB7总线,从而检验模块之工作状态.ROM(CGROM) 字型产生ROM(CGROM)提供8192个此触发器是用于模块屏幕显示开● 字型产生和关的控制。
DFF=1为开显示(DISPLAY ON),DDRAM 的内容就显示在屏幕上,DFF=0为关显示(DISPLAY OFF)。
DFF 的状态是指令DISPLAY ON/OFF和RST信号控制的。
●显示数据RAM(DDRAM)模块内部显示数据RAM 提供64×2个位元组的空间,最多可控制4行16字(64个字)的中文字型显示,当写入显示数据RAM时,可分别显示CGROM与CGRAM的字型;此模块可显示三种字型,分别是半角英数字型(16*8)、CGRAM字型及CGROM的中文字型,三种字型的选择,由在DDRAM中写入的编码选择,在 0000H—0006H的编码中(其代码分别是0000、0002、0004、0006共4个)将选择CGRAM的自定义字型,02H—7FH的编码中将选择半角英数字的字型,至于A1以上的编码将自动的结合下一个位元组,组成两个位元组的编码形成中文字型的编码BIG5(A140—D75F),GB (A1A0-F7FFH)。
RAM(CGRAM) 字型产生RAM提供图象定义(造字)功能, 可以提供四组16×16点的自● 字型产生定义图象空间,使用者可以将内部字型没有提供的图象字型自行定义到CGRAM中,便可和CGROM中的定义一样地通过DDRAM显示在屏幕中。
AC地址计数器是用来贮存DDRAM/CGRAM之一的地址,它可由设定指令暂存器来改变,● 地址计数器之后只要读取或是写入DDRAM/CGRAM的值时,地址计数器的值就会自动加一,当RS为“0”时而R/W 为“1”时,地址计数器的值会被读取到DB6——DB0中。
●光标/闪烁控制电路此模块提供硬体光标及闪烁控制电路,由地址计数器的值来指定DDRAM中的光标或闪烁位置。
外形尺寸ITEM NOMINAL DIMEN UNIT模块体积 93×78×12.5 mm视域 70.7×38.8 mm行列点阵数 128×64 dots点距离 0.52×0.52 mm点大小 0.48×0.48 mm三、液晶硬件接口1、逻辑工作电压(VDD):4.5~5.5V2、电源地(GND):0V3、工作温度(Ta):0~60℃(常温) / -20~75℃(宽温)4、电气特性见附图1 外部连接图(参考附图2)模块有并行和串行两种连接方法(时序如下):1、8位并行连接时序图MPU写资料到模块MPU从模块读出资料2、串行连接时序图四、用户指令集1、指令表1:(RE=0:基本指令集)指令表—2:(RE=1:扩充指令集)HS12864-12串口接线方式:备注:1、当模块在接受指令前,微处理顺必须先确认模块内部处于非忙碌状态,即读取BF标志时BF需为0,方可接受新的指令;如果在送出一个指令前并不检查BF标志,那么在前一个指令和这个指令中间必须延迟一段较长的时间,即是等待前一个指令确实执行完成,指令执行的时间请参考指令表中的个别指令说明。
2“RE”为基本指令集与扩充指令集的选择控制位元,当变更“RE”位元后,往后的指令集将维持在最后的状态,除非再次变更“RE”位元,否则使用相同指令集时,不需每次重设“RE”位元。
具体指令介绍:1、清除显示CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L L L L L L L H功能:清除显示屏幕,把DDRAM位址计数器调整为“00H”2、位址归位CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L L L L L L H X功能:把DDRAM位址计数器调整为“00H”,游标回原点,该功能不影响显示DDRAM3、位址归位CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L L L L L H I/D S功能:把DDRAM位址计数器调整为“00H”,游标回原点,该功能不影响显示DDRAM功能:执行该命令后,所设置的行将显示在屏幕的第一行。
显示起始行是由Z地址计数器控制的,该命令自动将A0-A5位地址送入Z地址计数器,起始地址可以是0-63范围内任意一行。
Z地址计数器具有循环计数功能,用于显示行扫描同步,当扫描完一行后自动加一。
4、显示状态 开/关CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L L L L H D C B 功能: D=1;整体显示ON C=1;游标ON B=1;游标位置ON5、游标或显示移位控制CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L L L H S/C R/L X X 功能:设定游标的移动与显示的移位控制位:这个指令并不改变DDRAM的内容6、功能设定CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L L H DL X 0 RE X X 功能:DL=1(必须设为1) RE=1;扩充指令集动作 RE=0:基本指令集动作7、设定CGRAM位址CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L H AC5 AC4 AC3 AC2 AC1 AC0 功能:设定CGRAM位址到位址计数器(AC)8、设定DDRAM位址CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L H AC6 AC5 AC4 AC3 AC2 AC1 AC0 功能:设定DDRAM位址到位址计数器(AC)9、读取忙碌状态(BF)和位址CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L H BF AC6 AC5 AC4 AC3 AC2 AC1 AC0功能:读取忙碌状态(BF)可以确认内部动作是否完成,同时可以读出位址计数器(AC)的值 10、写资料到RAMCODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0H L D7 D6 D5 D4 D3 D2 D1 D0功能:写入资料到内部的RAM(DDRAM/CGRAM/TRAM/GDRAM)11、读出RAM的值CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0H H D7 D6 D5 D4 D3 D2 D1 D0功能:从内部RAM读取资料(DDRAM/CGRAM/TRAM/GDRAM)12、 待命模式(12H)CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L L L L L L L H功能:进入待命模式,执行其他命令都可终止待命模式13、卷动位址或IRAM位址选择(13H)CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L L L L L L H SR功能:SR=1;允许输入卷动位址 SR=0;允许输入IRAM位址14、反白选择(14H)CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L L L L L H R1 R0功能:选择4行中的任一行作反白显示,并可决定反白的与否15、睡眠模式(015H)CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L L L L H SL X X功能:SL=1;脱离睡眠模式 SL=0;进入睡眠模式16、扩充功能设定(016H)CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L L H H X 1 RE G L功能:RE=1;扩充指令集动作 RE=0;基本指令集动作 G=1;绘图显示ON G=0;绘图显示OFF 17、设定IRAM位址或卷动位址(017H)CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L L H AC5 AC4 AC3 AC2 AC1 AC0功能:SR=1;AC5~AC0为垂直卷动位址 SR=0;AC3~AC0写ICONRAM位址18、设定绘图RAM位址(018H)CODE: RW RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0L L H AC6 AC5 AC4 AC3 AC2 AC1 AC0功能:设定GDRAM位址到位址计数器(AC)五、显示坐标关系1、图形显示坐标2、汉字显示坐标X坐标Line180H81H82H83H84H85H86H87HLine290H91H92H93H94H95H96H97HLine388H89H8AH8BH8CH8DH8EH8FHLine498H99H9AH9BH9CH9DH9EH9FH六、显示步骤1、显示资料RAM(DDRAM)显示资料RAM提供64×2个位元组的空间,最多可以控制4行16字(64个字)的中文字型显示,当写入显示资料RAM时,可以分别显示CGROM、HCGROM与CGRAM的字型;ST7920A可以显示三种字型 ,分别是半宽的HCGROM 字型、CGRAM字型及中文CGROM字型 ,三种字型的选择,由在DDRAM中写入的编码选择,在0000H—0006H的编码中将自动的结合下一个位元组,组成两个位元组的编码达成中文字型 的编码(A140—D75F),各种字型详细编码如下:1、显示半宽字型 :将8位元资料写入DDRAM中,范围为02H—7FH的编码。