MIL-PRF-6085D
表面光洁度标准
5.当元件质量指标要求划痕等级为20或优于此等级时,元件表面不准有 密集划痕即在元件中任何一个6.35mm面积的区域,不允许有4条或4条 以上的大等于10#划痕.
例:表面质量指标为20-10,20mm, 在如图(1)所示的区或有2条长1mm 和2条长0.5mm的10#划痕. 它符合5.1.1;5.1.4 (无需考虑5.1.2;5.1.3) 但它不符合5.1.5条.元件不合格 不合格. 不合格
18
编号13样品光洁度?
19
气泡和包络: 气泡和包络:包络当作气泡考虑. 依据美国军用标准MIL-PRF-13830B气泡的级数与麻点一 样,单位也相同.不规则气泡直也是取最大宽度和长度 的平均值. 气泡的允许值与麻点相同.但气泡和包络必须与麻点区 分开来,单独评价. 有灰斑的元件为不合格元件 不合格元件. 不合格元件
例:有一长30mm宽10mm的元件,元件的表面质量要求为60—40,元件上有2条 2mm的60#划痕,3条4mm的40#划痕. 它的等效直径 直径为20mm 直径 1/4D为1/4×20=5mm 最大划痕的长度和 长度和为: 长度和
40#划痕长4mm 60#划痕长2mm
2mm+2mm=4mm 4mm<5mm.符合2条. 但所有级数的划痕乘以划痕长度与元件直径之比所得乘积之和为: 1.60#划痕长度为(2+2);40#划痕长度为(4+4+4+4) 2.60#划痕乘以划痕长度与元件直径之比为60×(2+2)/20; 40#划痕乘以划痕长度与元件直径之比为40×(4+4+4+4)/20 3.所有级数的划痕乘以划痕长度与元件直径之比所得乘积之和为: [60×(2+2)/20]+[40×(4+4+4+4)/20=36 元件最大划痕级数为60;60的一半为60/2=30)36>30;因此,元件不合格 ; 不合格. 不合格
步步高MSD控制技术规范
步步高通信公司MSD控制技术规范1 目的、范围与简介:1.1目的为改进MSD控制水平，有效提高产品质量和可靠性，同时，提高技术人员对潮敏器件的认识水平，规范研发、市场和生产阶段对易潮敏器件的正确处理。
1.2范围本规范规定了潮湿敏感器件等级要求、包装要求、操作及处理方法等方面的技术指标和控制措施。
本规范适用于步步高通信公司及其子公司、分公司、办事处等分支机构（以下简称公司）潮湿敏感器件的控制。
合资企业和外协厂商均参照本规范执行。
1.3简介本规范遵照IPC/JEDEC有关的潮敏标准拟制，主要体现潮湿敏感器件在公司控制处理各环节的规范性要求。
本规范由塑封器件潮湿敏感定义、潮湿敏感器件分级要求、潮湿敏感器件包装要求、潮湿敏感器件干燥要求、潮湿敏感器件使用及注意事项等内容组成。
1.4关键词潮湿敏感、MSD、MSL、温度、相对湿度、干燥、烘烤、MBB23 术语和定义PSMD（Plastic Surface Mount Device）：塑料封装表面安装器件。
MSD（Moisture Sensitive Device）：潮湿敏感器件。
指非气密性封装的表面安装器件。
MSL（Moisture Sensitive Level）：潮湿敏感等级。
指MSD对潮湿环境的敏感程度。
MBB（Moisture Barrier Bag）：防潮包装袋。
MBB要求满足相应指标的抑制潮气渗透能力。
仓储寿命（Shelf Life）：指干燥包装的潮湿敏感器件能够储存在没有打开的内部环境湿度符合要求的湿气屏蔽包装袋中的最短时间。
车间寿命（Floor Life）：指湿度敏感器件从湿度屏蔽包装袋中取出或干燥储存或干燥烘烤后到过回流焊接前的时间。
制造商曝露时间（MET）：制造商烘烤完成至烤箱取出，到器件到达回流焊之前可能暴露到大气环境条件的最大累积时间。
干燥剂：一种能够保持相对低的湿度的吸收剂。
4 塑封器件潮湿敏感定义由于塑料封装材料的非气密性，塑封器件在潮湿环境中容易吸收水汽。
海军某型飞机表面清洗技术
文章编号: 1671 －8909( 2014) 4 －0001 －06海军某型飞机表面清洗技术陈跃良 1 ，王安东1* ，卞贵学 1 ，徐丽( 1. 海军航空工程学院青岛分院，山东青岛266041; 2. 海军航空兵学院，辽宁葫芦岛125001)摘要: 简要介绍了飞机表面清洗剂的基本类型及其主要性能指标。
通过对不同表面清洗方式的概述，提出了海军飞机表面清洗过程中的几点要求，包括有效性、安全性、经济性和规范化等。
同时结合海军某型飞机的真实服役环境数据及其表面清洗技术的实例，说明了飞机表面清洗的必要性，并着重叙述了清洗工作的具体操作步骤和相关注意事项。
关键词: 海军飞机; 表面清洗; 技术中图分类号: TP241; V267文献标识码: BExterior washing technology of navy aircraftCHEN Yueliang1 ，WANG Andong1* ，BIAN Guixue1 ，XU Li2( 1. Naval Aeronautical Engineering Institute，Qingdao，Shandong 266041，China;2. N aval A ir Force Academy，Huludao，Liaoning 125001，China)Abstract: The basic types and their key performance indicators of aircraft exterior cleaners are intro-duced briefly. Through t he summarization of different exterior cleaning methods，several requests of na-vy aircraft surface cleaning process are proposed，including efficacy，safety，economy and standardiza-tion and so on. Meanwhile the necessity of the surface cleaning of the aircraft and the emphasis de-scribes on specific steps and precautions related to the cleaning work are illustrated through combining with the real data of naval aircraft service environment and the surface cleaning technology example. Key words: Navy aircraft; exterior wash; technology我国的海军飞机大多分布在沿海地区，如宁波市、海口市等地。
航空电连接器
文案编辑词条B 添加义项?文案，原指放书的桌子，后来指在桌子上写字的人。
现在指的是公司或企业中从事文字工作的职位，就是以文字来表现已经制定的创意策略。
文案它不同于设计师用画面或其他手段的表现手法，它是一个与广告创意先后相继的表现的过程、发展的过程、深化的过程，多存在于广告公司，企业宣传，新闻策划等。
基本信息中文名称文案外文名称Copy目录1发展历程2主要工作3分类构成4基本要求5工作范围6文案写法7实际应用折叠编辑本段发展历程汉字"文案"(wén àn)是指古代官衙中掌管档案、负责起草文书的幕友,亦指官署中的公文、书信等;在现代，文案的称呼主要用在商业领域，其意义与中国古代所说的文案是有区别的。
在中国古代，文案亦作" 文按"。
公文案卷。
《北堂书钞》卷六八引《汉杂事》:"先是公府掾多不视事，但以文案为务。
"《晋书·桓温传》:"机务不可停废，常行文按宜为限日。
" 唐戴叔伦《答崔载华》诗:"文案日成堆，愁眉拽不开。
"《资治通鉴·晋孝武帝太元十四年》:"诸曹皆得良吏以掌文按。
"《花月痕》第五一回:" 荷生觉得自己是替他掌文案。
"旧时衙门里草拟文牍、掌管档案的幕僚，其地位比一般属吏高。
《老残游记》第四回:"像你老这样抚台央出文案老爷来请进去谈谈，这面子有多大!"夏衍《秋瑾传》序幕:"将这阮财富带回衙门去，要文案给他补一份状子。
"文案音译文案英文:copywriter、copy、copywriting文案拼音:wén àn现代文案的概念:文案来源于广告行业，是"广告文案"的简称，由copy writer翻译而来。
多指以语辞进行广告信息内容表现的形式，有广义和狭义之分，广义的广告文案包括标题、正文、口号的撰写和对广告形象的选择搭配;狭义的广告文案包括标题、正文、口号的撰写。
超精密金属膜电阻军用标准(RE)规格书
D
50 0 -55 70 175 (°C) (RE)功率 - 温度曲线
型号 额定功率 (W) 最大工作电压(V) 尺寸(Unit: mm) 阻值范围(Ω) 工作溫度范围 标称阻值误差
70 °C L ± 0.3 D ± 0.4 A ± 0.05
RE50 0.125 200 4.0 1.4 0.40
1 ~ 3M
RE55 0.25 200 6.9 2.05 0.60
0.05 ~ 10M
RE60 0.5 250 9.8 3.2 0.60
0.05 ~ 10M
RE65 0.75 300 12.5 3.6 0.60
0.05 ~ 10M
RE70 1.0 350 14.1 4.65 0.80
0.05 ~ 10M
RE75 1.5 500 17.8 7.2 0.80
长期
无机械损伤，飞弧，绝缘击穿 短期
GJB244A (MIL-PRF-55182) 3.17/3.22/3.23 ΔR≤±(0.20%R+0.01Ω)
无机械损伤
GJB244A (MIL-PRF-55182)3.20 ΔR≤±(0.10%R+0.01Ω)
无机械损伤
Version 2014
德键电子工业股份有限公司
要求
GJB244A (MIL-PRF-55182) 3.24 ΔR≤±(0.5%R+0.01Ω) ΔR≤±(2%R+0.01Ω) GJB244A (MIL-PRF-55182)3.21 ΔR≤±(0.4%R+0.01Ω) GJB244A (MIL-PRF-55182)3.25 ΔR≤±(2.0%R+0.01Ω) GJB244A (MIL-PRF-55182) 3.18/3.29/3.16 ΔR≤±(0.15%R+0.01Ω)
国内外军用电子元器件质量等级及对应情况
国外军用电子元器件质量等级与国内对应情况为了保证元器件的质量,我国制定了一系列的元器件标准。
在上世纪７０年代末期制定了“七专”790５技术协议和80年代初制定了“七专”8406技术协议，已具备了军用器件标准的雏形，但标准是在改革开放之前制定的,有很多局限性,很难与国际接轨.从８0年代开始，我国标准化部门参照了美国军用标准（MＩL)体系建立了ＧJB体系，元器件的标准有规范、标准、指导性文件等三种形式。
2。
美国军标质量等级体系:(1)B-2级：不完全符合MＩL—STD—883的1。
2。
１节的要求,并按照政府批准文件,包括卖方等效的B级要求进行采购。
(２）B-1级:完全符合MIL—STＤ－8８3（微电子器件试验方法和程序)的1。
2．1节所要求，并按照标准军用图样（SＭD –Stａndard Microｃiｃuit Drａwing），国防电子供应中心(DＥＳC –Deｆence ＥlｅｃtroniｃSｕpplyＣeｎｔｅr)图样或政府批准的其它文件进行采购。
即通常称883级，器件上有５962–xｘx号。
（３）S-1级:完全按照MIL-STD－9７5(NAＳＡ标准的电子电气和机电源器件目录）或MＩL-STD-１547（航天飞行器和运载火箭用元器件、材料和工艺技术要求）进行采购，并有采购机关的规范批准.电阻、电容、电感元件MIL 标准中有可靠性指标的元件失效等级分五级3.欧空局元器件半导体分立器件：ＥSA／ＳCC（EurｏpｅSpacｅAgｅncy／SpａcｅComponet Cooperａtｉｏｎ)5000标准试验等级:B级、C级(从高到低）批接收等级：1级、2级、3级（从高到低)微电路:ＥＳA/SＣC（Eurｏpe Ｓpace Aｇency／Spａｃe Comｐonet Coopｅratｉon)９００0标准试验等级：B级、C级（从高到低）批接收等级：1级、2级、3级（从高到低)电阻、电容、电感器件:EＳＡ/ＳCC(Ｅurｏpe Sｐace Ａｇency／ＳpaceＣomｐonet Ｃoopｅraｔｉon）３000和40０0标准试验等级：B级、C级(从高到低)批接收等级：1级、2级、3级（从高到低）4.国外军用元器件与我国军用元器件质量等级对应关系半导体分立器件质量等级对应关系微电路质量对应等级国内外库存管理现状分析一、概要库存管理是指在物流过程中商品数量的管理，过去认为仓库里的商品多，表明企业发达、兴隆。
美国军用标准MIL
柔性可热封静电防护材料特性规范美国军用标准MIL-PRF-81705D上海防静电工业协会王福良译本规范已批准用于军队的所有部门与国防部承包商。
1 范围1．1范围本规范建立了一套军用微电路、敏感半导体器件，敏感电阻和相关高档部件的柔性可热封静电防护包装材料的要求。
另外I型材料可提供防水防电磁辐射的性能（见6.1）。
1．2分类防护材料有以下三种类型：I类防水、防静电、静电屏蔽和电磁屏蔽。
1型无使用限制。
2型仅适用于自动制袋机。
II类透明、防水、静电耗散型。
1型无使用限制。
2型仅适用于自动制袋机。
III类透明、防水、防静电、静电屏蔽。
1型无使用限制。
2型仅适用于自动制袋机。
2 应用文件2.1 概述本节列出的文件由本规范第3、4节作出详细规定与说明。
本节所列文件不包括本规范其他章节引用的文件或附加建议的信息和例子。
尽管已努力做到确保所列文件的完整性，但文件使用者应注意必须满足本规范第3、4节所规定的要求。
不管它们是否已被列入表中。
2.2 政府文件2.2.1 规范、标准和手册下面的规范、标准和手册是本文件的组成部分。
除非另有规定，这些已列入国防部规范，标准和附录索引的文件均可被引用。
规范联邦文件QQ-S-698 片状和条状低碳钢QQ-A-250/4 铝合金、板状和片状标准FED-STD-101 包装材料的测试程序2.3 非政府出版物下列文件是本规范的扩展部分。
除非另有规定，国防部已采用的列入索引的文件可以被引用，没被列入索引的要求可参见6.2。
ANSI（美国国家标准协学会）J-STD-006焊料合金等级，有助焊剂和无助焊剂。
固体焊料应用要求。
ASQC（美国质量协会）ASQC-Z1.4 程序，检验抽样表（国防部已采用）ASTM-B451 用于印刷板的铜箔，铜棒，铜片和传送带规范ASTM-D257 绝缘材料的直流电阻或传导率（国防部已采用）ASTM-F15 铁-镍-钴封焊合金规范ASTM（美国试验与材料协会）EIA（电子工业协会）EIA-541 静电敏感物体的包装材料标准2.4 优先权当本文件与引用的参考文件发生矛盾时，则本文件优先。
PEM标准
Type Thread Size .112-40 (#4-40)
UNIFIED
Non-Locking Fastener Material Steel Stainless Steel AS AS AS AS AS AS AS AC AC AC AC AC AC AC
440 632 832 024NS 032 0420 0428NS
.289 .327 .367 .405 .405 .514 .514
.290 .335 .365 .405 .405 .510 .510
.36 .39 .44 .47 .47 .60 .60
.13 .13 .13 .17 .17 .21 .21
Black Dry-film Black Zinc per Lubricant per Dry-film ASTM MIL-PRF-46010 Passivated Lubricant 70 or B 633 over and/or per Less on SC1 (5µm) Cadmium tested per MIL-L-46010 the Type III, Chromate ASTM over Rockwell Colorless Prime A380 Silver “B” Scale • • • •
mounting hole over the shank of the fastener.
.25” / 8 mm Min. PUNCH
sheet. Do not perform any secondary operations such as deburring.
3.
With the punch and anvil surfaces parallel, apply sufficient squeezing force until flange contacts mounting sheet. Sketch at right shows suggested tooling for applying these forces. Installation force and performance data shown below.
特殊材料检测项目及标准参考(1)
4
90°剥离强度
胶粘剂 90°剥离强度测定方法 （金属金属）
GJB 446-1988
5
高强度胶粘剂 剥离强度
高强度胶粘剂剥离强度的测定 浮辊 法
GB/T 7122-1996
1
胶粘剂
胶粘剂 180°剥离强度试验方法 （挠性 材料对刚性材料） GB/T 2790-1995 6 180°剥离强度
硫化橡胶与金属粘接 180°剥离试验 GB/T 15254-1994
增强材料 纱线试验方法第 3 部分： 玻 璃纤维断裂强力和断裂伸长的测定 GB/T 7690.3-2001
2
断裂强力和断 裂伸长 增强材料 机织物试验方法第 5 部分： 玻璃纤维拉伸断裂强力和断裂伸长的 测定
GB/T 7689.5-2001
碳素材料碳、氢、氮含量测定方法 3 碳、氢、氮 QJ 2781A-2004
11
粘度
胶黏剂黏度的测定单圆筒旋转黏度计 法 GB/T 2794-2013
1
胶粘剂
12
不挥发物含量
胶粘剂不挥发物含量的测定 GB/T 2793-1995
2
橡胶
1
拉伸应力应变 性能
硫化橡胶或热塑性橡胶拉伸应力应变 性能的测定 GB/T 528-2009
2
邵尔硬度
硫化橡胶或热塑性橡胶压入硬度试验 方法 第 1 部分：邵氏硬度计法（邵尔 硬度）GB/T 531.1-2008
热分析方法通则 1 热分析 JY/T 014-1996
2 9 固体材料
成分分析
微束分析 能谱法定量分析 GB/T 17359-2012
只测 B5～U92
固体材料高温热扩散率试验方法激光 脉冲法 3 高温热扩散率 GJB 1201.1-1991
干燥剂标准介绍
⼲燥剂标准介绍⼲燥剂标准介绍1、药品⾷品⼲燥剂相关标准药品⾷品⽤⼲燥剂的标准主要是由国家⾷品药品监督管理局制定的药品包装容器(材料)标准：《药⽤固体纸袋装⼲燥剂标准》YBB00122005。
该标准规定了对“固体制剂滤纸袋包装的细孔球型硅胶⼲燥剂”的要求，其中除了对⼲燥剂袋外观、强度，吸附剂的含⽔率、吸湿率等⼲燥剂基本性能要求外，着重就⼲燥剂在有害物质含量（如：砷含量等），微⽣物限度，脱⾊性能等⽅⾯进⾏了规定。
威胜针对药⽤⾷品⽤⼲燥剂，专门制定了两种产品标准，分别为《⼩圆柱⼲燥剂产品标准》WS-QWS-824-55和《透明条连续式⼲燥剂产品标准》WS-QWS-824-56，这两种产品在满⾜YBB00122005的基础上，增加了吸湿速度要求、粉尘要求、交货⽅式等要求，另外有使产品更适合进⾏⾃动化分装的要求。
具体差异见下表：交货要求产品规格及包装数量—已规定已规定药⽤⼲燥剂的包装袋要求也要符合药包材规定包装袋要求—符合YBB00072005 符合YBB00172002湿度指⽰卡—8% 8%其他透明条连续式横封及纵封——规定了试验⽅法及验收标准使透明条连续式⼲燥剂能适应⾃动化分装注：1“—”代表没有此项要求2、DIN55473标准《包装辅助⽤品⼲燥剂袋交货技术条件》DIN5473标准是德国标准化协会针对袋装⼲燥剂制定的⼀个标准，标准中对袋装⼲燥剂的原料性能、包材性能、成品性能、包装袋（阻隔性包装）性能、产品标识等均作了明确的规定。
A、原料（吸附剂）性能要求检验项⽬指标测试或检验⽅法PH 3.5~8.5 ⽔溶液PH计测定电导率≤0.3S/m⽔溶液电导率仪测定⽔溶物含量≤2.0%⽔溶液过滤蒸发法粒度≤0.25mm ≤2.0%≤6.3mm 100%标准⾦属筛⽹筛选单位吸湿能⼒（23℃、40%RH）≥6g动态法或恒温恒湿箱法测试吸湿能⼒百分⽐后根据单位重量换算⽽得单位重量②≤39g ⽣产前根据吸湿能⼒百分⽐制订单位重量数值，⽣产后根据⼲燥剂袋内吸附剂净重确认实际的单位重量数值单位体积≤45cm3测量堆积密度后根据单位重量换算⽽得B、包材（⼲燥剂袋⼦的材料，透⽓性包装）性能要求检验项⽬指标测试或检验⽅法防粉尘性A型：≤10mg/u带包装跌落试验，收集粉尘称重B型：≤1mg吸湿速度23℃、40%RH ≤16u：≥0.25g/7h·u带包装动态吸附7⼩时测试增重32u：≥0.1 g/7h·u印刷及标识⾄少需印刷有以下内容：1.⼲燥剂 DIN554732.⼚家名称及通信地址3.DIN检验标志及注册号（我司注册号为5B010）4.⼲燥剂单位数量（只允许有1/6、1/3、1/2、1、2、4、8、16、32单位）5.⼲燥剂袋的类型（A型或B型）不允许标有重量⽬视C、包装袋（阻隔性包装）检验项⽬指标测试或检验⽅法⽔蒸⽓透过率23℃、85%RH≤0.5g/m2·24h电解法测试⽔蒸⽓透过率湿度指⽰卡每袋8%点卡⽬视印刷及标识需印刷有以下内容（英⽂、德⽂）：1.注意！对潮⽓敏感；2.湿度指⽰卡必须为蓝⾊；3.应在使⽤时打开。
表面光洁度标准
左图是大家看的编号3的样品。 （图片是放大的不是实际尺寸）
图中有5条划痕，该元件直径为 6mm；对于表面质量要求20-10 该产品不合格。对于表面质量要 求40-20则该产品所有级数乘以划
痕长度与元件直径之比所得乘积之 和为： 20×2.2/5+10×7/5=8.8+17=25.8 25.8<40。元件符合40-20
A区的麻点直径的和: =40+20+10=70 < 40×2=80 B区的麻点直径的和: =20×2+10×4+5×1=85> 80， B区不合格。 因此元件不合格。
0.2mm A 区 B区 C 区
左图元件表面质量要求60-40： A区麻点直径和为10+10+20=40<80. B区麻点直径和为10 × 3+20 × 3=90>80. C区麻点直径和为20 ×2+10=50<80. B区不合格该元件不合格。
D 2
ah
B区：80-50
1mm
A区：20-10
3mm 4mm
2mm
A区等效直径为（1+3）/2=2mm B区等效直径为（2+4）/2=3mm
MILDF铝铬化中文版
MIL -DTL - 5541F铝和铝合金的化学转化膜1.范围范围..此规格涉及通过与表面爲铝和铝合金的化学转化材料反应而组成的化学转化膜..分类..化学转化膜有如下类型和等级..类型..化学转化膜有如下类型见3.1：类型I—包含六价铬的组成物类型II—无六价铬的组成物1.2.2 等级..通过于铝和铝合金化学反应贰组成的材料有如下等级见6.1和6.4等级1A—爲最大限度保护防止喷涂的或者未喷涂处的腐蚀、等级3—爲保护防止需低电性阻值处的腐蚀2. 适用文件2.1 大意：此部分所列文件在本说明的第三和第四部分都有详细列明..本部分不包含此说明中其他章节所引用的文件;推荐的附加信息文件以及用作事例的文件..爲确保此清单的完整性已作出很多努力;文件使用者应注意;必须满足章节3或4引用文件的要求;不管这些文件有没有在此列明..2.2 政府文件2.2.1 规格和标准..以下规格和标准组成本文件的一部分..除非特别指定;这些文件的问题引用在恳请或合同中..联邦标准FED-STD-141--- 喷涂、油漆、涂漆和其他相关材料：检验、抽验和测试的方法国防部标准MIL-PRF-23377 --- 涂底漆：环氧基树脂;高固形化MIL-DTL-81706--- 用于涂覆铝及铝合金的化学转化膜MIL-PRF-85582--- 涂底漆：环氧基树脂;waterborne这些文件的副本可以在网站或者在线查看;或者也可以从位于PA191 11-5094费城4D大厦700罗宾逊大街的标准文件预定服务台索取2.3 非政府出版物..以下规格和标准组成本文件的一部分..除非特别指定;这些文件的问题引用在恳请或合同中..美国材料试验协会ASTM-B117 ---- 盐雾试验仪器操作ASTM-D3359--- 胶带附着力测试这些文件副本可以从位于PA19428-2959 ;west conshohocken; ASTM 获得或者从网站了解美国质量协会ASQASQ-Z 1.4 --- 通过属性进行程序;抽样及台板检验此文件副本可从位于美国密尔沃基市的美国质量协会获得或从网站了解到..汽车工程师协会SAESAE-AMS4027----铝合金薄片和薄板;1.0Mg-0.60Si-0.28Cu-0.20Cr;606 1；薄片是T6;薄板T651;溶液沈淀经热处理SAE-AMS4037---铝合金薄片和薄板;4.4Mg-1.5Si-0.60Cu-0.20Cr;2024；平薄片T3;薄板T351;溶液经热处理这些文件副本可从SAE获得或从网站http：了解到2.4 优先级别..如果发生此文件文字部分与此引用的参考相冲突;优先考虑本文件的文字部分..然而;文件中任何条款都不能超越适用法律及规章;除非获得特殊赦免..3. 要求3.1 材料.. 如果没有规定材料类型;使用类型I..除非在合同或订单中有声明;类型I代替类型II;或者类型II代替类型I;都是不允许..用来生産化学转化膜的材料应就选择类型、等级、形式及申请方法等方面受批准;使其与MIL-DTL-81760相符合并且应已被接受列入适用合格産品清单见6.5.. 补充化学物质;如加入浴室中维持其效率的氟化物;应不能减少所应用膜的性能..3.2 清洗.. 涂覆前;底部金属应机械或化学清洗;使得冲洗过后获得一个water break-free的表面..含带研磨料类铁如钢丝网、铁氧化物、红铁粉或者钢丝线在所有清洗操作中均不允许..弄脏的处理部件应使用能移除脏污的材料清洗;并且这种材料不能破坏底部金属、部件或者转化膜..如果转化膜遭破坏;破坏区域应重新清洗再重新涂覆;或者拒收此部件..3.3 应用..除非一种应用方法在合同或订单中有说明;化学转化膜应在所有热处理后通过喷洒、刷涂或沈浸非电解地应用;并且机械操作如成型、穿孔、机械加工、合金焊接等已经完成见6.11和6.14..组装件包含的非铝件有可能被化学转化流程袭击、弄碎或破坏;所以不应被涂覆除非这些非铝件被保护..3.4 修补..转化膜移除掉的机械损坏区域;如果在合同或订单中有声明;需修补或拒收..损坏区域应用MIL-DTL-81706材料修补;这种材料就应用类型、等级、形式和方法在QPL-81706得到认可..修补区域应不大于整个表面积的5%见6.4和6.17..3.5 外观..化学转化膜外观应持续并且在日光下清洗可见..它应没有粉末状或松散膜、空洞、刮痕、裂缝;以及其他会降低零件服务能力或者对保护值和喷涂绑定性质有害的不良或损伤.. 接触标志的尺寸和数量应最小并且一直良好..如果在合同或订单中有规定;接触标志MIL-DTL-81706材料修补来阻止局部腐蚀;这种材料就应用类型、等级、形式和方法在QP L-81706得到认可见6.4和6.8..3.6 性能特征3.6.1 耐腐蚀..4.4.1所述168小时暴露于5%盐雾测试结束后;经用适用等级转化膜处理的测试标本件4.2.2应满足以下耐腐蚀要求见6.14：a. 根据测试标本;不能有5处隔离的斑点或哇坑见6.9;其直径不能大于0.031inch..离边角0.25inch区域、辨别标示及处理或盐雾暴露时的等待点排除在外..顔色的遗失应不做拒收的理由..b. 在所有5个测试样本的联合表面区域;据盐雾测试;不超过15个隔离的斑点或哇坑;直径不能大于0.031inch..3.6.2 油漆附着力湿胶带..当生産油漆系统6.13或者描述的油漆系统应用于可适用的测试样本时见4.2.2;根据4.4.2测试根据ASTM-D3359 程序A;4A的附着力等级或者更高;内涂分离不能发生在油漆系统和转化膜之间;或者转化膜和底部金属之间..如果转化膜部件终端不需要喷涂;油漆附着力测试也许可以省除;如果此测试被特殊授权..3.7 等级三转化膜的电性接触电阻..电性接触电阻测试应在合同或订单中有规定见6.4..测试方法;测试频率及所需的阻值应被规定以满足特殊应用需要..3.8 转化膜溶液的化学分析..转化膜溶液的化学分析应包含容度、ph值及温度评估来确定液池在化学物质厂商规定的范围之内见6.11..3.9 工艺.. 此规格涉及的化学转化膜应使用生産此规格中所描述的涂覆零件的处理和流程来生産..4. 确认4.1 检验的分类..在此规定的检验要求分类如下：a. 流程控制检验见4.2b. 一致性检验见4.34.2流程控制检验4.2.1流程控制测试和溶液分析..测试样本的测试应符合表格I和除了表格I中测试;还需针对所有在化学转化线见3.8上的流程溶液进行溶液分析以确保化学容度在设立的最适宜性能范围之内见6.11和6.14..流程控制测试是用来确定化学转化膜符合此规格要求并且可以作爲采用设备和程序获得特征的鉴证..流程控制测试和溶液分析的频率..溶液分析至少应一周一次见6.15.. 表格I中所描写的流程控制测试至少每月一次..另外;每月测试的间隔期不应超过35天..如果符合本规格的生産没有35天或更多的时间测测试;那麽流程控制测试和溶液分析要在生産的重新开始进行..4.2.2 流程控制测试样本..用来流程控制特使的测试样本英3英寸宽;1 0英寸长;并且名义厚度不能超过0.020英寸..生産运行时测试样本需用五金处理;包括所有的预处理和后处理如清洗和冲洗;除下列描述之外..除非合同或订单中特别说明见6.4;否则需使用下面流程控制测试样本合金选择之一..选择1----每月流程控制期间应爲每种合金和处理调剂使用一组测试样本选择 2---测试样本需爲符合SAE-AMS4037等级1A转化膜的2024-T3铝合金;以及符合SAE-AMS4037等级3的6061-T6铝合金测试样本..对于测试等级3转化膜;2024-T3铝合金也许可用来代替6061-T6铝合金测试样本见6.10..当处理铸件所用清洗程序对制成的测试样本有害时;测试样本必须以合格的方式清洗见3.2并且转化膜覆盖铸件..如果生産零件非2024-T3铝合金并且蚀刻或脱氧剂也许对测试样本有害时;应适用厂商建议的清洗操作..油漆附着力样本的准备..除非在合同或订单中特别描述见6.4;用于附着力测试的测试样本油漆系统英和生産工作使用的爲同一系统和生産工作使用同一种方式或者是所述油漆系统....环氧树脂涂底漆. 测试样本需配备一层膜;这层膜是根据MIL-PRF-23377或者MIL-PRF-85582符合挥发性有机化合物VOC的环氧树脂聚酰亚胺底漆.在任何一种情况下;底漆需应用于厚度爲0.0006至0.0009英寸0.6至0. 9mil的一层干膜上并且在测试前根据所适用的底漆规范弄干..4.2.3 失败..对于任何不能遵循表格I中流程控制要求的失败需立即停止生産..在生産恢复前;失败的原因应确定并且得到改正..从上一次可接受的流程控制测试到失败的确定;所有可追踪的和可改正的工作应抵制; 除非此工作审查时被证明是满足此规范要求..除非特别声明;已经喷涂或结合入组装的部件应不能视爲可改正的..4.3 合格检验4.3.1 抽样检验..取作外观检查的样品应从物品、项目、部件或零件的每个批次见4.3.2中选择..除非在合同或订单中有特别说明见6.4和6.1 8;抽样计划和接受标准应爲ASQZ1.4检验等级II所述一致..4.3.2 批次目视检查..所选择符合4.4 测试方法5. 包装5.1 不适用6. 注释此章节包含大概或解释性质的信息;这些信息有可能有用但不是强制性的6.1 预期用途..本规范覆盖的化学转化膜将用于未阳极氧化的铝和铝合金基材;遍及国防部门..它们被用于修复铝上阳极化化学膜..它们被指定爲应用于许多军事平台的离子蒸汽沈积IVD一种后处理;作爲一种镉的代替品或者直流电阻蚀剂..类型I和类型II化学转化膜给未喷涂项目提供防腐蚀保护;另外提高铝和铝合金上喷涂处理系统的附着力..此规范鉴于其用于航空的特殊性质;覆盖的化学转化膜超出商业可用産品;6.2 检验责任..除非合同或订单另有说明;否则合同商应负责操作在此所述的所有检验要求检查和测试..除非合同或订单另有说明;并且未得到政府认可;否则合同商也许利用自己或其他合适设备来实行在此规定的检验..政府保留进行规格中提出的任何检验的权利;在此规格中这些检验被视爲必要来确保供应和符合符合规定要求..6.3 符合责任..所有项目必须满足章节3要求..此规格提出的检验鼻血成爲合同商总体检验系统或质量方案的一部分..规格中任何检验要求的缺失不会减轻合同商的责任;此责任爲合同商需确保所有提交至政府的産品或供应应符合合同的所有要求..作爲制造商操作的一部分;样品检验爲一可接受的动作来确保符合要求;然而;这并不表示认可屈服指示的或实际的已知不良材料;也不表示政府对不良材料的接受..6.4 采购要求..采购文件应规定如下：a. 规格的标题、数量和日期c. 应用的方法;如果被限制见3.3d．如果机械损坏区域被允许修补见3.4e．无色化学膜;如果被要求见3.5f．如果接触标志允许修补见3.5h．电性阻值测试;如果等级三化学膜有要求见3.7和6.12i．当电性阻值测试时;规定所需要的阻值、测试频率和测试方法见3. 7和6.12l．所需求数量6.5 可交换性.. 符合规格MIL-DTL-81706受认可的以及列在QPL-81706的各种産品;提供每个类型和等级相当的化学膜..这些化学膜在就化学转化膜的性能至此规格的配给是相当的;但是从化学物质角度看;是不可以替换的..换句话说;不同的材料是不能混合在一起..对于类型I中材料;化学膜存在的确认可用在ASTM-B449定义的简单当场测试..对于类型II材料;化学膜的存在需根据厂商的建议来确认..6.9 腐蚀点和洼坑的确认..一般来说;腐蚀点和洼坑通常是显示典型的尾部或线;然而;任何可见的腐蚀点和洼坑要计数;除非是刮痕或者是基材表面..6.11 转化溶液的化学分析.. 注意许多转化材料不能在低温下与铝表面充分起作用..在一年较冷的时间;不推荐把部件的转化膜置入不加热设备;如飞机棚..6.12 喷涂附着力..在后续喷涂或者附着力失效发生之前;涂覆部件应按照化学厂商的建议允许干燥..当涂覆部件喷涂前存储了大量时间;它们应被按照3.2清洗;通过移除灰尘粒子来重新启动表面..过厚的转化膜可能导致喷涂附着力问题;例如起泡;是由于喷涂下较高可溶材料所産生..6.13 喷涂兼容性..转化膜和某种化学试剂防腐蚀涂料CARC之间的兼容性已经被报告..6.14 腐蚀保护的温度影响..未喷涂的化学转化膜;如果在干燥、后续制造或服务期间暴露于140F60摄氏度或更高温度;将会开始失去耐腐蚀性质..随着温度和暴露时间的增加;未喷涂转化膜部件的防腐蚀保护将会下降..此下降被认爲是因爲化学转化膜的脱水以及转化膜内铬酸盐所産生的不溶性..6.15 溶液分析文件..每个处理液缸历史文件需保存;这些文件显示液缸中所添加补充化学物质和所有溶液分析的结果..溶液的测试应和最好的行业准则和厂商建议所一致..在采购活动的要求下;例如记录以及测试结果的报告应制作好..在合同或订单结束后;这些记录的保存应不小于一年..6.16 保存期限..此规格涉及保存期限需考虑的项目..特定的保存期限要求需在合同或采购订单中有说明..保存期限代码在联邦物流信息系统总体项目记录中有包含..保存期限的附加信息也许可从DoD1410.27-M获得;保存期限供应商不能被混淆或者被用来从另一个材料供应商增强所存在的溶液..由于化学转化膜材料是专利産品;所以配方、流程、应用方法如喷雾、涂刷或者沈浸以及涂覆应用所需要的设备也许会有所改变..合同商和军事活动必须在采购、部件的设计以及设施的建立考虑此内容..根据此规格要求处理部件的详细图纸应规定等级1A或3;所需要的类型I或II;以及任何需满足理想性能的喷涂系统..如果转化膜没有规定;建议等级1A..6.6 清洗剂..优先适用无蚀刻清洗剂;尤其是对于精致合金..如果适用蚀刻清洗剂;必须注意阻止洼坑或晶间腐蚀的産生..这对于使用碱性侵蚀尤爲重要;因爲铝比它的合金元素和存在的金属间易于溶解;金属间例如有铜会在之后可能暴露..最终;碱性侵蚀应避免尤其是清洗组装结构..如果使用碱性侵蚀;应通常伴随酸性中和步骤..6.7 抗磨损性..化学转化膜的抗磨损性相对较低..化学转化膜在适度使用时可以保持相当持久;但很容易被严重磨损或腐蚀所移除..然而;冷成型操作;当小心作业时;能应用于处理金属上而不对化学膜産生可感知的损坏..6.8 目视检查.. 最简单评估化学转化膜的方法是观察顔色、外观的连续性、平滑度和对于底部金属的附着力见3.5.. 目视检查的执行是爲了确保合适的清洗和涂覆流程有使用;致使具有足够保护的转化膜存在于整个部件上..在MIL-DTL-81706下合格的材料生産的化学转化膜;这些转化膜顔色从无色到彩虹黄、褐色、灰色或蓝色..通过使用色卡来爲某个涂覆系统开发可接受的顔色级别也许是可能的..以下与顔色一致性相关的情况可能存在：a. 当多种合金被用同种转化材料处理时;顔色可能在合金之间有所变化..b. 由于在铝焊接和铸造表面的高度不纯和氧化;顔色可能和通过处理精致的合金所获得的效果不一致..C．当部件从处理罐中提起时;由于化学转化物质的滴溅;黑点可能会産生..一小数量的黑点并不导致转化膜的退化;但必须在处理后通过快速冲洗部件和使用合适的网架技术尽量减少黑点..如果转化膜的保护值被赃污或被干燥过热而损坏;目视检查不能揭露..如果需要本色涂覆;检验的困难可能会産生因爲目视检查不能发现转化膜的存在..。
MIL-PRF-19500中文资料
MIL-PRF-19500/376E 31 August 2000SUPERSEDINGMIL-PRF-19500/376D 21 August 1998PERFORMANCE SPECIFICATIONSEMICONDUCTOR DEVICE, TRANSISTOR, NPN, SILICON, LOW-POWERTYPES 2N2484, 2N2484UA, 2N2484UB, JAN, JANTX, JANTXV, JANS, JANHC, AND JANKCThis specification is approved for use by all Departments and Agencies of the Department of Defense.1. SCOPE1.1 Scope. This specification covers the performance requirements for NPN, silicon, low-power transistors. Four levels of product assurance is provided for each device type as specified in MIL-PRF-19500. Two levels of product assurance are provided for die.1.2 Physical dimensions. See figure 1 (similar to T0-18), figures 2 and 3 (surface mount case outlines UA and UB), and figures 4 and 5 (die).1.3 Maximum ratings.P TV CBOV EBOV CEOI CT J and T STGR θJAR θJCTypesT A = +25°CmWV dc V dc V dc mA dc °C °C/W °C/W 2N2484500 (1)6066050-65 to +2003251462N2484UA 650 (2)6066050-65 to +2002101602N2484UB500 (1)6066050-65 to +200325146(1)Derate linearly at 3.08 mW/°C above T A = +37.5°C (2)Derate linearly at 4.76 mW/°C above T A = +63.5°C. 1.4 Primary electrical characteristics.h feC obo|h fe |2V CE(sat) (1)LimitsV CE = 5 V dc I C = 1 mA dc f = 1 kHzI E = 0V CB = 5 V dc 100 kHz ≤ f ≤ 1 MHzI C = 500 µA dc V CE = 5 V dc f = 30 MHzI C = 1.0 mA dc I B = 0.1 mA dcMin Max250900pF5.02.07.0V dc 0.3(1) Pulsed (see 4.5.1).AMSC N/AFSC 5961DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.The documentation and process conversion measures necessary to comply with this revision shall be completed by 31 November 2000.INCH-POUND Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC/VAC,Post Office Box 3990, Columbus, OH 43216-5000, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter.2Dimensions Symbol Inches Millimeters NoteMin Max Min Max CD .178.195 4.52 4.95CH .170.210 4.32 5.33HD .209.230 5.31 5.84LC .100 TP 2.54 TP 6LD .016.0210.410.537,8LL .500.75012.7019.057,8LU .016.0190.410.487,8L1---.050--- 1.277,8L2.250--- 6.35---7,8Q ---.040---0.865TL .028.0480.71 1.223,4TW .036.0460.91 1.173r ---.010---0.2510α45° TP 45° TP6NOTES:1.Dimension are in inches.2.Metric equivalents are given for general information only.3.Beyond r (radius) maximum, TW shall be held for a minimum length of .011 (0.28 mm).4.Dimension TL measured from maximum HD.5.Body contour optional within zone defined by HD, CD, and Q.6.Leads at gauge plane .054 +.001 -.000 inch (1.37 +0.03 -0.00 mm) below seating plane shallbe within .007 inch (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC.7.Dimension LU applies between L 1 and L 2. Dimension LD applies between L 2 and LLminimum. Diameter is uncontrolled in L 1 and beyond LL minimum.8.All three leads.9.The collector shall be internally connected to the case.10.Dimension r (radius) applies to both inside corners of tab.11.In accordance with ANSI Y14.5M, diameters are equivalent to φx symbology.12.Lead 1 = emitter, lead 2 = base, lead 3 = collector.FIGURE 1. Physical dimensions (similar to TO-18).3DimensionsSymbol Inches Millimeters Note Min Max Min Max A .061.075 1.55 1.903A1.029.0410.74 1.04B1.022.0280.560.71B2.075 REF 1.91 REF B3.006.0220.150.565D .145.155 3.68 3.93D1.045.055 1.14 1.39D2.0375 BSC .952 BSC D3---.155--- 3.93E .215.225 5.46 5.71E3---.225--- 5.71L1.032.0480.81 1.22L2.072.088 1.83 2.23L3.003.0070.080.185NOTES:1.Dimensions are in inches.2.Metric equivalents are given for general information only.3.Dimension "A" controls the overall package thickness. When a window lid is used, dimension "A" mustincrease by a minimum of .010 inch (0.254 mm) and a maximum of .040 inch (1.020 mm).4.The corner shape (square, notch, radius, etc.) may vary at the manufacturer's option, from that shown onthe drawing.5.Dimensions "B3" minimum and "L3" minimum and the appropriately castellation length define anunobstructed three-dimensional space traversing all of the ceramic layers in which a castellation was designed. (Castellations are required on bottom two layers, optional on top ceramic layer.) Dimension "B3" maximum and "L3" maximum define the maximum width and depth of the castellation at any point on its surface. Measurement of these dimensions may be made prior to solder dipping.6.Lead 4 = no connection.FIGURE 2. Physical dimensions, surface mount (2N2484UA).4DimensionsInches Millimeters NotesLtrMin.Max.Min.Max.A .046.0560.97 1.42A1.017.0350.430.89B1.016 .024 0.41 0.61 3D .085 .108 2.41 2.74 D1 .071 .079 1.81 2.01 D2 .035 .039 0.89 0.99 D3E .115 .128 2.82 3.25 E3 L1.022.0380.560.964NOTES:1.Dimensions are in inches.2.Metric equivalents are given for general information only.3.Dimensions B2 and B3 are identical to B14.Dimension L2 is identical to L1.FIGURE 3. Physical dimensions, surface mount (2N2484UB).5A- versionNOTES:1.Die size...............................................0.015 x 0.019 inches ± 0.001 inch2.Die thickness.......................................0.010 ± 0.0015 inches3.Top metal............................................Aluminum 15,000Å minimum, 18,000Å nominal4.Back metal..........................................A.Gold 2,500Å minimum, 3,000Å nominalB.Eutectic Mount – No Gold5.Backside.............................................Collector6.Bonding pad........................................B = 0.003 inches, E = 0.004 inches diameter7.Passivation.........................................Si 3N 4 (Silicon Nitride) 2kÅ min, 2.2kÅ nom.FIGURE 4. Physical dimensions, JANHC and JANKC die, A - version.B - versionDie size:.....................................................0.018 x 0.018 inchesDie thickness:............................................0.008 ± 0.0016 inchesBase pad:..................................................0.0025 inches diameterEmitter pad:...............................................0.003 inches diameterBack metal:................................................Gold, 6500 ± 1950 ÅTop metal:.................................................Aluminum, 19500 ± 2500 ÅBack side:..................................................Collector Glassivation:..............................................SiO2, 7500 ± 1500 ÅFIGURE 5. Physical dimensions, JANHC and JANKC die, B - version.61.4 Primary electrical characteristics.NFI C = 10 µA dc, V CE = 5 V dcR g = 10 kΩh FE2h FE5f = 100 Hz f = 1000 Hz f = 10 kHz V CE = 5 V dcI C = 10 µA dc V CE = 5 V dc I C = 1 mA dcMin Max dB7.5dB3dB22005002508002. APPLICABLE DOCUMENTS2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed.2.2 Government documents.2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2).SPECIFICATIONDEPARTMENT OF DEFENSEMIL-PRF-19500 - Semiconductor Devices, General Specification for.STANDARDDEPARTMENT OF DEFENSEMIL-STD-750 - Test Methods for Semiconductor Devices.(Unless otherwise indicated, copies of the above specifications, standards, and handbooks are available from the Document Automation and Production Services (DAPS), Building 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.)2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.73. REQUIREMENTS3.1 General. The requirements for acquiring the product described herein shall consist of this document and MIL-PRF-19500.3.2 Qualification. Devices furnished under this specification shall be products that are manufactured by a manufacturer authorized by the qualifying activity for listing on the applicable qualified manufacturer’s list (QML) before contract award (see4.2 and 6.3).3.3 Abbreviations, symbols, and definitions. Abbreviations, symbols, and definitions used herein shall be as specified in MIL-PRF-19500.3.4 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-19500 and figures 1, 2, 3, 4, and 5 herein.3.4.1 Lead finish. Unless otherwise specified, lead finish shall be solderable in accordance with MIL-PRF-19500, and herein.3.5 Marking. Marking shall be in accordance with MIL-PRF-19500. At the option of the manufacturer, marking may be omitted from the body, but shall be retained on the initial container.3.6 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in 1.3, 1.4, and table I.3.7 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table I herein.3.8 Workmanship. Semiconductor devices shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance.4. VERIFICATION4.1 Classification of inspections. The inspection requirements specified herein are classified as follows:a. Qualification inspection (see 4.2).b. Screening (see 4.3).c. Conformance inspection (see 4.4).4.2 Qualification inspection. Qualification inspection shall be in accordance with MIL-PRF-19500 and as specified herein.4.2.1. JANHC and JANKC Qualification. JANHC and JANKC qualification inspection shall be in accordance with MIL-PRF-19500.84.3 Screening (JANS, JANTX, and JANTXV levels only). Screening shall be in accordance with table IV of MIL-PRF-19500, and as specified herein. The following measurements shall be made in accordance with table I herein. Devices that exceed the limits of table I herein shall not be acceptable.Screen (see tableIVMeasurementof MIL-PRF-19500)JANS level JANTX and JANTXV levels 3c Thermal impedance (see 4.3.2)Thermal impedance (see 4.3.2)9I CBO2, h FE4Not applicable1048 hours minimum48 hours minimum11I CBO2; h FE4;∆I CBO2 = 100% of initial value or 2 nA dc,whichever is greater.∆h FE4 = ±15%I CBO2 ,h FE412See 4.3.1240 hours minimum See 4.3.180 hours minimum13Subgroups 2 and 3 of table I herein;∆I CBO2 = 100% of initial value or 2 nA dc,whichever is greater;∆h FE4 = ±15%Subgroup 2 of table I herein;∆I CBO2 = 100% of initial value or 2 nA dc, whichever is greater;∆h FE4 = ±25%4.3.1 Power burn-in conditions. Power burn-in conditions are as follows: V CB = 10 to 30 V dc:Power shall be applied to achieve T J = 135°C minimum and a minimum power dissipation = 75 percent of maximum rated P T (see 1.3). T A = room ambient as defined in 4.5 of MIL-STD-750.NOTE: No heat sink or forced air cooling on the devices shall be permitted.4.3.2 Thermal impedance (ZθJX measurements). The ZθJX measurements shall be performed in accordance with method 3131 of MIL-STD-750.a. I M measurement current-------------5 mA.b. I H forward heating current -----------50 mA (min).c. t H heating time -------------------------25 - 30 ms.d. t md measurement delay time ------60 µs max.e. V CE collector-emitter voltage ------10 V dc minimum.The maximum limit for ZθJX under these test conditions are ZθJX (max) = 150°C/W for 2N2484, ZθJX (max) = 67°C/W for 2N2484UA and 2N2484UB.94.4 Conformance inspection. Conformance inspection shall be in accordance with MIL-PRF-19500, and as specified herein. If alternate screening is being performed in accordance with MIL-PRF-19500, a sample of screened devices shall be submitted to and pass the requirements of group A1 and A2 inspection only (table VIb, group B, subgroup 1 is not required to be performed again if group B has already been satisfied in accordance with 4.4.2).4.4.1 Group A inspection. Group A inspection shall be conducted in accordance with MIL-PRF-19500 and table I herein.4.4.2 Group B inspection. Group B inspection shall be conducted in accordance with the conditions specified for subgroup testing in table VIa (JANS) of MIL-PRF-19500 and 4.4.2.1. Electrical measurements (end-points) shall be in accordance with group A, subgroup 2 herein. Delta requirements shall be in accordance with table III herein. See 4.4.2.2 for JAN, JANTX, and JANTXV group B testing. Electrical measurements (end-points) and delta requirements for JAN, JANTX, and JANTXV shall be after each step in 4.4.2.2 and shall be in accordance with group A, subgroup 2 herein. Delta requirements shall be after each step and shall be in accordance with table III herein.4.4.2.1 Group B inspection, table VIa (JANS) of MIL-PRF-19500.Subgroup Method ConditionB41037V CB = 10 V dcB5 1027V CB = 10 V dc; T A = +125°C ±25°C for 96 hours with P T adjusted according to the chosen T A to give T J = +275°C minimum. Optionally, the test may be conducted forminimum 216 hours with P T adjusted to achieve T J = 225°C minimum, sample size (foroption) n = 45, c = 0. In this case, the ambient temperature shall be adjusted such that aminimum 75 percent of maximum rated P T (see 1.3) is applied to the device under test.(Note: If a failure occurs, resubmission shall be at the test conditions of the originalsample.)4.4.2.2 Group B inspection, (JAN, JANTX, and JANTXV). Separate samples may be used for each step. In the event of a group B failure, the manufacturer may pull a new sample at double size from either the failed assembly lot or from another assembly lot from the same wafer lot. If the new “assembly lot” option is exercised, the failed assembly lot shall be scrapped.Step Method Condition11039Steady-state life: Test condition B, 340 hours, V CB = 10 -30 V dc, T J = 150°C min.,external heating of the device under test to achieve T J = +150°C minimum is allowedprovided that a minimum of 75% of rated power is dissipated. No heat sink or forced-aircooling on the devices shall be permitted. n = 45 devices, c = 021039The steady state life test of step 1 shall be extended to 1,000 hours for each die design.Samples shall be selected from a wafer lot every twelve months of wafer production.Group B, step 2 shall not be required more than once for any single wafer lot. n = 45,c = 0.31032High-temperature life (non-operating), t = 340 hours, T A = +200°C. n = 22, c = 0.104.4.2.3 Group B sample selection. Samples selected from group B inspection shall meet all of the following requirements:a.For JAN, JANTX, and JANTXV, samples shall be selected randomly from a minimum of three wafers (orfrom each wafer in the lot) from each wafer lot. For JANS, samples shall be selected from each inspection lot. See MIL-PRF-19500.b.Must be chosen from an inspection lot that has been submitted to and passed group A, subgroup 2conformance inspection. When the final lead finish is solder or any plating prone to oxidation at hightemperature, the samples for life test (subgroups B4 and B5 for JANS, and group B for JAN, JANTX, and JANTXV) may be pulled prior to the application of final lead finish.4.4.3 Group C inspection, Group C inspection shall be conducted in accordance with the conditions specified for subgroup testing in table VII of MIL-PRF-19500, and in 4.4.3.1 (JANS).and 4.4.3.2 (JAN, JANTX, and JANTXV) herein for group C testing. Electrical measurements (end-points) shall be in accordance with group A, subgroup 2 herein. Delta requirements shall be in accordance with table III herein.4.4.3.1 Group C inspection, table VII (JANS) of MIL-PRF-19500.Subgroup Method ConditionC22036Test condition E (not applicable to UA and UB suffix devices).C610261,000 hours at V CB = 10 -30 V dc; power shall be applied to achieve T J = 150°C minimum and a minimum power dissipation P D = 75 percent of maximum rated P T as defined in 1.3herein.4.4.3.2 Group C inspection, table VII (JAN, JANTX, and JANTXV) of MIL-PRF-19500.Subgroup Method ConditionC2 2036Test condition E (not applicable to UA and UB suffix devices).C6Not applicable.4.4.3.3 Group C sample selection. Samples for subgroups in group C shall be chosen at random from any inspection lot containing the intended package type and lead finish procured to the same specification which is submitted to and passes group A tests for conformance inspection. Testing of a subgroup using a single device type enclosed in the intended package type shall be considered as complying with the requirements for that subgroup.4.4.4 Group E inspection. Group E inspection shall be performed for qualification or re-qualification only. The tests specified in table II herein must be performed to maintain qualification.4.5 Method of inspection. Methods of inspection shall be as specified in the appropriate tables and as follows.4.5.1 Pulse measurements. Conditions for pulse measurement shall be as specified in section 4 of MIL-STD-750.1112TABLE I. Group A inspection.MIL-STD-750LimitInspection 1/MethodConditionsSymbolMinMaxUnitSubgroup 1 2/Visual and mechanical examination 3/2071n = 45 devices, c = 0Solderability 3/ 4/2026n = 15 leads, c = 0Resistance to solvents 3/ 4/ 5/1022n = 15 devices, c = 0Temperature cycling 3/ 4/1051Test condition C, 25 cycles.n = 22 devices, c = 0 Hermetic seal 4/1071n = 22 devices, c = 0Fine leak Gross leakElectrical measurements 4/Group A, subgroup 2Bond strength 3/ 4/2037Precondition T A = +250°C at t = 24 hrs or T A = 300°C at t = 2 hrs; n = 11 wires, c = 0Subgroup 2Collector to emitter breakdown voltage3011Bias condition D; I C = 10 mA dc pulsed (see 4.5.1)V (BR)CEO 60V dcCollector to base cutoff current 3036Bias condition D; V CB = 60 V dc I CBO110µA dc Emitter to base cutoff current 3061Bias condition D; V EB = 6 V dc I EBO110µA dc Collector to base cutoff current 3036Bias condition D; V CB = 45 V dc I CBO25nA dc Collector to emitter cutoff current3041Bias condition D; V CE = 5 V dc I CEO 2nA dc Emitter to base cutoff current 3061Bias condition D; V EB = 5 V dc I EBO22nA dc Collector to emitter cutoff current3041Bias condition C; V CE = 45 V dc I CES 5nA dcForward-current transfer ratio3076V CE = 5 V dc; I C = 1 µA dch FE145See footnote at end of table.13TABLE I. Group A inspection - Continued.MIL-STD-750LimitInspection 1/MethodConditionsSymbolMinMaxUnitSubgroup 2 - continued.Forward-current transfer ratio 3076V CE = 5 V dc; I C = 10 µA dc h FE2200500Forward-current transfer ratio 3076V CE = 5 V dc; I C = 100 µA dc h FE3225675Forward-current transfer ratio 3076V CE = 5 V dc; I C = 500 µA dc h FE4250800Forward-current transfer ratio 3076V CE = 5 V dc; I C = 1 mA dc h FE5250800Forward-current transfer ratio 3076V CE = 5 V dc; I C = 10 mA dc pulsed (see 4.5.1)h FE6225800Collector to emitter voltage (saturated)3071I C = 1.0 mA dc; I B = 100 µA dc V CE(sat)0.3V dc Base emitter voltage (nonsaturated)3066Test condition B; V CE = 5 V dc;I C = 100 µA dcV BE(ON)0.50.7V dcSubgroup 3High-temperature operation T A = +150°CCollector to base cutoff current 3036Bias condition D; V CB = 45 V dc I CBO310µA dcLow-temperature operation T A = -55°CForward-current transfer ratio 3076V CE = 5 V dc; I C = 10 µA dch FE735Subgroup 4Magnitude of common emitter small-signal short-circuit forward-current transfer ratio 3306V CE = 5 V dc; I C = 50 µA dc;f = 5 MHz|h fe |13.0Magnitude of common emitter small-signal short-circuitforward- current transfer ratio 3306V CE = 5 V dc; I C = 500 µA dc;f = 30 MHz|h fe |2 2.07.0Small-signal open-circuit output admittance3216V CE = 5 V dc; I C = 1.0 mA dc;f = 1 kHzh oe 40µmhosSmall-signal open- circuit reverse-voltage transfer ratio 3211V CE = 5 V dc; I C = 1.0 mA dc;f = 1 kHzh re 8.0 x 10-4Small-signal short- circuit input impedance3201V CE = 5 V dc; I C = 1 mA dc;f = 1 kHzh ie3.524k ΩSee footnote at end of table.14TABLE I. Group A inspection - Continued.MIL-STD-750LimitInspection 1/MethodConditionsSymbolMinMaxUnitSubgroup 4 - continued.Small-signal short- circuit forward current transfer ratio 3206V CE = 5 V dc; I C = 1 mA dc;f = 1 kHzh fe 250900Open circuit output capacitance3236V CB = 5 V dc; I E = 0;100 kHz ≤ f ≤ 1 MHz C obo 5.0pFInput capacitance (output open-circuited)3240V EB = 0.5 V dc; I C = 0;100 kHz ≤ f ≤ 1 MHzC ibo 6.0pF Noise figure3246f = 100 Hz; V CE = 5 V dc; I C = 10µA dc; Rg = 10 k Ω;NF17.5dBNoise figure 3246 f = 1 kHz; V CE = 5 V dc; I C = 10µA dc; R g = 10 k Ω;NF23dBNoise figure 3246 f = 10 kHz; V CE = 5 V dc; I C = 10µA dc; R g = 10 k Ω;NF32dBNoise figure (wideband)3246Noise bandwidth = 10 Hz to 15.7kHz; V CE = 5 V dc; I C = 10 µA dc;R g = 10 k Ω;NF43dBSubgroups 5 and 6Not applicable Subgroup 7 4/Decap internal visual (design verification)2075n = 1 device, c = 01/For sampling plan see MIL-PRF-19500.2/For resubmission of failed subgroup A1, double the sample size of the failed test or sequence of tests. Afailure in group A, subgroup 1 shall not require retest of the entire subgroup. Only the failed test shall be rerun upon submission.3/Separate samples may be used.4/Not required for JANS devices.5/Not required for laser marked devices.TABLE II. Group E inspection (all quality levels) - For qualification only.Inspection MIL-STD-750QualificationMethod ConditionsSubgroup 1Temperature cycling (air to air)Hermetic sealFine leakGross leak Electrical measurements Subgroup 2 Intermittent lifeElectrical measurements Subgroup 3Not applicable Subgroup 4Not applicable Subgroup 5Not applicable 105110711037Test condition C, 500 cyclesSee group A, subgroup 2 and table III herein.Intermittent operation life: V CB = 10 V dc ,6,000 cycles.See group A, subgroup 2 and table III herein.12 devicesc = 045 devicesc = 015TABLE III. Groups B and C delta measurements. 1/ 2/ 3/Step Inspection MIL-STD-750Symbol Limit UnitMethod Conditions1Forward-current transfer ratio 3076V CE = 5 V dc; I C = 500µA dc; pulsed see 4.5.14/∆h FE4±25 percent change frominitial recorded reading2.Collector to emittervoltage (saturated)3071I C = 1.0 mA dc; I B = 100µA dc∆V CE(sat)4/ 5/±50 mV dc change frompreviously measured value.3.Collector to emittercutoff current 3041Bias condition C;V CB = 45 V dc∆I CES4/100 percent of initial valueor 2 nA dc, whichever isgreater.1/The delta measurements for group B, table VIa (JANS) of MIL-PRF-19500 are as follows:a.Subgroup 4, see table III herein, step 2.b.Subgroup 5, see table III herein, steps 1 and 3.2/The delta measurements for 4.4.2.2 herein (group B, JAN, JANTX, and JANTXV) are as follows: Steps 2 and 3 of table III shall be performed after each step in 4.4.2.2 herein.3/The delta measurements for group C, table VII of MIL-PRF-19500 are as follows: Subgroup 6, see table III herein, steps 1 and 3 for JANS, step 1 for JAN, JANTX, and JANTXV.4/Devices which exceed the group A limits for this test shall not be accepted.5/Applies to JANS level only.165. PACKAGING5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see6.2). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points' packaging activity within the Military Department or Defense Agency, or within the Military Departments' System Command. Packaging data retrieval is available from the managing Military Departments' or Defense Agency's automated packaging files, CD-ROM products, or by contacting the responsible packaging activity.6. NOTES(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.)6.1 Intended use. The notes specified in MIL-PRF-19500 are applicable to this specification.6.2 Acquisition requirements. Acquisition documents should specify the following:a.Title, number, and date of this specification.b.Issue of DoDISS to be cited in the solicitation, and if required, the specific issue of individual documentsreferenced (see 2.2.1).c.Lead formation and finish may be specified (see 3.4.1).d.Type designation and product assurance level.e.Packaging requirements (see 5.1).6.3 Qualification. With respect to products requiring qualification, awards will be made only for products which are, at the time of award of contract, qualified for inclusion in Qualified Manufacturers List QML-19500 whether or not such products have actually been so listed by that date. The attention of the contractors is called to these requirements, and manufacturers are urged to arrange to have the products that they propose to offer to the Federal Government tested for qualification in order that they may be eligible to be awarded contracts or orders for the products covered by this specification. Information pertaining to qualification of products may be obtained from Defense Supply Center, Columbus, ATTN: DSCC-VQE, P.O. Box 3990, Columbus, OH 43216-5000.6.4 Suppliers of JANHC die. The qualified JANHC suppliers with the applicable letter version (example JANHCA1N645-1) will be identified on the QML.JANC ordering informationPIN Manufacturer43611341562N2484JANHCA2N2484JANHCB2N2484JANKCA2N2484JANKCB2N24846.5 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes.17。
航空化工品件号对应规范标准
航空化⼯品件号对应规范标准序号品名包装标准规范1 Mobil Jet Oil II24X1QT/CTN MIL-PRF-23699F STD2 Mobil Jet Oil II5GAL/PAIL MIL-PRF-23699F STD3 Mobil Jet Oil II55GAL/DRUM MIL-PRF-23699F STD4 Mobil Jet Oil 25424X1QT/CTN MIL-PRF-23699F HTS5 Mobil Jet Oil 25455GAL/DRUM MIL-PRF-23699F HTS6Mobilgrease 284X2KG/CTN MIL-G-81322E Gr A7Mobilgrease 2816KG/PAIL MIL-G-81322E Gr A8Mobilgrease 334X2KG/CTN MIL-PRF-23827, TY I9Mobilgrease 3316KG/PAIL MIL-PRF-23827, TY I10Mobil Aviation Grease SHC 1006X5LB/CTN CML04-03511Mobil Aviation Grease SHC 10016KG/PAIL CML04-03512Mobil Aviation Grease SHC 10050KG/DRUM CML04-03513Exxon Hyjet IV-Aplus24X1QT/CTN BMS3-11M TY V, GRB &TY IV，CL114Exxon Hyjet IV-Aplus5GAL/PAIL BMS3-11M TY V, GRB &TY IV，CL115Exxon Hyjet V24X1QT/CTN SAE AS1241,BMS3-11 TY V16Exxon Aviation Oil Elite 20W-5012X1QT/CTN MIL-L-2285117Exxon Aviation Oil 20W-5012X1QT/CTN MIL-L-6082E18Mobil Aero HFS5GAL/PAIL MIL-PRF-8328219Mobil Aero HF5GAL/PAIL MIL-PRF-560620Mobil DTE 2418L/PAIL21Mobilcut 32118L/PAIL22Exxsol D60(S) Fluid156KG/DRUM23Mobil DTE Light Oil18L/PAIL24Skydrol LD-46X1GAL/CTN BMS3-11M TY IV, CL1, TY V, GR B&C, BAMS564-003 25Skydrol LD-424X1QT/CTN BMS3-11M TY IV, CL1, TY V, GR B&C, BAMS564-003 26Skydrol 500B-424X1QT/CTN BMS3-11 TY IV, CL227Skydrol 56X1GAL/CTN BMS3-11 TY V, GR B28MCS 352B 5.4OZ/EA BAC550629Skykleen 10005GAL/PAIL BAC550430Aeroshell Grease 54X3KG/CTN MIL-G-3545C31Aeroshell Grease 64X3KG/CTN MIL-PRF-24139A32Aeroshell Grease 74X3KG/CTN MIL-PRF-23827C TYPE II35Aeroshell Grease 144X3KG/CTN MIL-G-25537C36AeroShell Grease 154X3KG/CTN15.875KG/PAIL37Aeroshell Grease 224X3KG/CTN MIL-PRF-81322F GR238Aeroshell Grease 334X3KG/CTN MIL-PRF-23827C TY II39Aeroshell Grease 33MS4X3KG/CTN MIL-G-21164D40Aeroshell Grease 33MS17KG/PAIL MIL-G-21164D41AeroShell Grease 43C6X2.95KG/CTN SAE-AMS-G-434342AeroShell Compound 54X3KG/CTN MIL-C-11796C CL343Aeroshell Compound 824X0.79KG/CTN44AeroShell Fluid 120L/PAIL45AeroShell Fluid 1209L/DR46AeroShell Calibrating Fluid 255GAL/DRUM MIL-PRF-7024E Type II47AeroShell Fluid 2F5GAL/PAIL MIL-C-6529C TYPE II48AeroShell Fluid 2XN5GAL/PAIL49Aeroshell Fluid 31GAL/CAN MIL-PRF-7870C50Aeroshell Fluid 35GAL/PAIL MIL-PRF-7870C51Aeroshell Fluid 126X1GAL/CTN MIL-PRF-6085D52AeroShell Fluid 186X1GAL/CTN53AeroShell Fluid 311GAL/CAN MIL-PRF-83282D54Aeroshell Fluid 4112X1L/CTN MIL-PRF-5606H55Aeroshell Fluid 416X1GAL/CTN MIL-PRF-5606H56Aeroshell Fluid 414X5L/CTN MIL-PRF-5606H57Aeroshell Fluid 4120L/PAIL MIL-PRF-5606H58AeroShell Fluid 5L-A5GAL/PAIL MIL-PRF-6086E Light Grade 59Aeroshell Fluid 5M-A5GAL/PAIL MIL-PRF-6086E Medium GR 60Aeroshell Fluid 5M-A6X1GAL/CTN MIL-PRF-6086E Medium GR 61AeroShell Fluid 61208L/DR MIL-PRF-46170C Type I*62AeroShell Fluid 7118.9L/PAIL MIL-PRF-6083F63Aeroshell LGF5GAL/PAIL BMS 3-32A TY II64AeroShell Fluid S.835020L/PAIL65AeroShell Fluid SSF5GAL/PAIL BMS 3-32A TY I66AeroShell Turbine Oil 25GAL/PAIL67AeroShell Turbine Oil 320L/PAIL AIR 3515/B, O-135, OM-11 68AeroShell Turbine Oil 30824X1QT/CTN MIL-PRF-7808 Gr.369AeroShell Turbine Oil 39012X1L/CTN OX-7, DEF STAN 91-9470AeroShell Turbine Oil 39020L/PAIL OX-7, DEF STAN 91-9473AeroShell Turbine Oil 56024X1QT/CTN MIL-PRF-23699F HTS74AeroShell Turbine Oil 560208L/DR MIL-PRF-23699F HTS75AeroShell Turbine Oil 75012X1L/CTN AIR 3517, O-149, OX-3876AeroShell Turbine Oil 75020L/PAIL AIR 3517, O-149, OX-3877AeroShell Oil 6512X1QT/CTN J-1966 SAE Grade 3078AeroShell Oil 8012X1QT/CTN J-1966 SAE Grade 4079Aeroshell Oil 10012X1QT/CTN J-1966 SAE Grade 5080Aeroshell Oil 10020L/PAIL J-1966 SAE Grade 5081Aeroshell Oil 100205L/DR J-1966 SAE Grade 5082AeroShell Oil 120205L/DR J-1966 SAE Grade 6083AeroShell Oil Diesel 10W4012X1L/CTN N.A84AeroShell Oil W 15W-5012X1QT/CTN J-1899 SAE Grade Multigrade 85AeroShell Oil W 15W-5020L/PAIL J-1899 SAE Grade Multigrade 86AeroShell Oil W6512X1QT/CTN J-1899 SAE Grade 3087AeroShell Oil W8012X1QT/CTN J-1899 SAE Grade 4088Aeroshell Oil W10012X1QT/CTN J-1899,SAE,Grade 5089Aeroshell Oil W1001GAL/CAN J-1899,SAE,Grade 5090Aeroshell Oil W10020L/PAIL J-1899,SAE,Grade 5091Aeroshell Oil W100205L/DRUM J-1899,SAE,Grade 5092AeroShell Oil W12020L/PAIL J-1899 SAE Grade 6093Shell Cassida LTS400G/CAN N.A94Shell water Detector80PCS/BOX N.A95Nylon Syringe PC N.A96Shell EP 75W9012X1L/CTN N.A97Shell Avgas 100LL200L/DRUM N.A98Shell Helix ULTRA 5W-306X4L/CTN N.A99Shell Tellus Oil 2218L/PAIL100Shell Tellus Oil 4618L/PAIL101Shell Tellus Oil 46208L/DRUM102Shell Clavus G6818L/PAIL103Shell Clavus G68209L/DRUM104Turco 1495-X20L/PAIL AMS 1650105Turco 3878 LF-NC20L/PAIL BAC 5763106Turco 418125KG/BAG AMS 1379107Turco 4215 NC-LT23KG/PAIL BAC 5749110Turco 446020L/PAIL BMS11-7 TYPE I111Turco 4460-BK20L/PAIL BMS 5750112Turco 4848-9220L/PAIL MIL-D-16791 TYPE I113Turco 535120L/PAIL AMS 1375114Turco 580520L/PAIL AMS 1545115Turco 588420L/PAIL MIL-C-85704116Turco 5948 DPM20L/PAIL AMS 1530117Turco 5948 DPM200L/DRUM AMS 1530118Turco 5948 DPM Thick20L/PAIL AMS 1530119Turco 622620L/PAIL BMS 5750120Turco 664620L/PAIL RR-OMAT 1/270121Turco 6776-LO20L/PAIL BAC 5725122Turco 6780200L/DRUM AMS 1534123Turco 678020L/PAIL AMS 1534124Turco 6783-5020L/PAIL MIL-C-85704 Ty II125Turco Ind 7920L/PAIL CCT-LA714126Turco P-D-680 Type I20L/PAIL MIL-PRF-680 TYPE I127Turco P-D-680 Type II20L/PAIL MIL-PRF-680 TYPE II128Turco TT-N-95 Type II20L/PAIL B00083129Turco Lustrite 220L/PAIL AMS 1531130Alodine 60010LB/PAIL MIL-C-5541131Alodine 10011QT/CAN MIL-C-5541132Alodine 1000L25KG/PAIL133Alodine 113212EA/BOX BAC 5719134Alodine 1200S1LB/CAN MIL-C-5541135Alodine 1200S10LB/PAIL MIL-C-5541136Alodine 12015KG/PAIL MIL-C-5541137Alodine 15005KG/PAIL MIL-C-5541138EA 934NA1QT/KIT MMM-A-132 TYPE 1, CLASS 3 139EA 9561QT/KIT 140EA 9561PT/KIT141EA 9601QT/KIT142EA 960F3QT/KIT143EA 9309NA1QT/KIT146EA 93301QT/KIT147EA 93451GAL/KIT148EA 93901QT/KIT BMS8-301 CL1, GR1149EA 93941QT/KIT BMS5-109 TYPE II150EA 9394/C-21QT/KIT151EA 93951QT/KIT152EA 93961QT/KIT MMM-A-132, REV A, TYPE 1, CL 3 153EA 9689 .100 PSF GL36"X150'/RL 154EA 9891RP1PT/KIT155Loctite C5-A1LB/CAN MIL-PRF-907E156Loctite C-200 1.3LB/CAN157Loctite Moly Dry Film Lubricant 1.3LB/CAN158Loctite Moly Dry Film Lubricant10LB/CAN159Loctite Moly 501LB/CAN MIL-T-83483160Loctite 0783150ML/EA MIL-S-22473161Loctite 0803150ML/EA162Loctite 0843150ML/EA MIL-S-22473E GR C163Loctite 0883150ML/EA MIL-S-22473E GR A164Loctite 0893150ML/EA MIL-S-22473E GR A165Loctite 22150ML/EA OMAT8/68B166Loctite 22250ML/EA MIL-S-46163A TYPE II GR M167Loctite 24150ML/EA MIL-S-46163A TYPE I GR J168Loctite 24250ML/EA MIL-S-46163A TYPE II169Loctite 24350ML/EA170Loctite 24819G/EA171Loctite 26250ML/EA MIL-S-46163A TYPE II GR O172Loctite 27050ML/EA MIL-R-46092 TYPE I173Loctite 27150ML/EA MIL-R-46092 TYPEI174Loctite 271250ML/EA MIL-R-46092 TYPEI175Loctite 27250ML/EA176Loctite 27350ML/EA177Loctite 27450ML/EA178Loctite 29050ML/EA MIL-S-22473179Loctite 30750ML/EA182Loctite 33050ML+52ML/KIT183Loctite 40120G/EA184Loctite 40620G/EA185Loctite 41020G/EA186Loctite 41420G/EA MIL-A-36050C TYPE 2 CL2深圳市华迅贸易有限公司完全产品清单 2008/10/19序号品名包装标准规范187Loctite 41520G/EA MIL-A-46050C TYPE I CL III 188Loctite 42520G/EA189Loctite 44420G/EA190Loctite 45420G/EA191Loctite 48020G/EA192Loctite 49520G/EA193Loctite 49620G/EA MIL-A-46050C TYPE I CL II 194Loctite 51050ML/EA195Loctite 51550ML/EA196Loctite 51850G/EA197Loctite 54250ML/EA198Loctite 542250ML/EA199Loctite 54550ML/EA200Loctite 56750ML/EA201Loctite 56950ML/EA202Loctite 57250ML/EA203Loctite 572250ML/EA204Loctite 57750ML/EA205Loctite 58650ML/EA206Loctite 60150ML/EA207Loctite 60350ML/EA208Loctite 60950ML/EA MIL-R-46082B TYPE I 209Loctite 615 3.2OZ/KIT PWA586210Loctite 62050ML/EA MIL-R-46082B TYPE II 211Loctite 638250ML/EA212Loctite 64050ML/EA MIL-R-46082B TYPE II215Loctite 66050MLEA216Loctite 67250ML/EA217Loctite 675250ML/EA MIL-R-46082B TYPE I218Loctite 68050ML/EA219Loctite 755340G/EA220Loctite 767236ML/EA221Loctite 770 1.75OZ/EA222Loctite 485020ML/EA223Loctite 5366310ML/EA224Loctite 5910370G/EA225Loctite 707015OZ/EA226Loctite 7075 4.5OZ/EA227Loctite 7387 1.75OZ/EA228Loctite 740020ML/EA229Loctite 745252ML/EA230Loctite Locquic Primer T 7471 1.75OZ/EA MIL-S-22473E GR T FORM R 231Loctite Primer N 7649 4.5OZ/EA MIL-S-22473E GR N FORM R232LPS 1 Greaseless Lubricant11OZ/CAN MIL-C-23411A233LPS 1 Greaseless Lubricant1GAL/CAN MIL-C-23411A234LPS 1 Greaseless Lubricant5GAL/PAIL MIL-C-23411A235LPS 2 Industrial-Strength Lubricant11OZ/CAN MIL-C-16173D GR 3 CL 1 236LPS 2 Industrial-Strength Lubricant1GAL/CAN MIL-C-16173D GR 3 CL 1 237LPS 2 Industrial-Strength Lubricant5GAL/PAIL MIL-C-16173D GR 3 CL 1 238LPS 3 Heavy-Duty Rust Inhibitor11OZ/CAN MIL-C-16173D GR 2 CL 1 239LPS 3 Heavy-Duty Rust Inhibitor1GAL/CAN MIL-C-16173D GR 2 CL 1 240LPS 3 Heavy-Duty Rust Inhibitor5GAL/PAIL MIL-C-16173D GR 2 CL 1 241LPS CFC Free Electro Contact Cleaner11OZ/CAN MIL-PRF-29608242LPS CFC Free Electro Contact Cleaner1GAL/CAN MIL-PRF-29608 243LPS CFC Free Electro Contact Cleaner5GAL/PAIL MIL-PRF-29608 244LPS Electro 140o11OZ/CAN245LPS F-104 Fast Dry Solvent15OZ/CAN Airbus ABR 9-0140 TYPE I246LPS PreSolve Citrus Degreaser15OZ/CAN Boeing D6-17487 Rev. H 247LPS Electra-X Nonflamable Contact248LPS INSTANT SUPER DEGREASER20OZ/CAN Boeing D6-17487 Rev. P 249BP Turbine Oil 238024X1QT/CTN MIL-PRF-23699F-STD 250BP Turbine Oil 23891QT/CAN Mil-PRF-7808L Gr3251Braycote 23612X1LB/CTN VV-P-236A252Braycote 24835LB/PAIL MIL-C-11796C, Class 3253Brayco 5895GAL/PAIL MIL-PRF-8188D254Brayco 59912X8OZ/CTN D50TF6-S1255Braycote 65512X1LB/CTN MIL-T-5544256Braycote 86812X1LB/CTN DOD-L-25681D257Brayco 92255GAL/DRUM MIL-PRF-7024E Type II258Brayco Micronic 7621GAL/CAN259Optimol Paste White T100G/EA260Royco 1MS 1.75LB/CAN MIL-T-83483261Royco 10 1.75LB/CAN262Royco 11MS35LB/PAIL DPM 6480263Royco 13CF 1.75LB/CAN MIL-G-25013E264Royco 13CF35LB/PAIL MIL-G-25013E265Royco 22CF35LB/PAIL MIL-PRF-81322F GR NLGI 2266Royco 22MS 1.75LB/CAN MIL-G-81827A267Royco 22MS35LB/PAIL MIL-G-81827A268Royco 27 1.75LB/CAN MIL-PRF-23827C269Royco 27 6.5LB/CAN MIL-PRF-23827C270Royco 32 1.75LB/CAN MIL-G-6032271Royco 43 6.5LB/CAN SAE-AMS-G-4343272Royco 44 1.75LB/CAN MIL-T-5544B273Royco 465GAL/PAIL MIL-L-46000 (LSA)274Royco 64 6.5LB/CAN MIL-G-21164D275Royco 81MS 1.75LB/CAN DOD-L-25681276Royco 308CA1GAL/CAN MIL-PRF-32033277Royco 3155GAL/PAIL MIL-PRF-3150278Royco 3631GAL/CAN MIL-PRF-7870C279Royco 3635GAL/PAIL MIL-PRF-7870C280Royco 4815GAL/PAIL MIL-PRF-6081281Royco 4825GAL/PAIL MIL-STD-2073-1C282Royco 4835GAL/PAIL MIL-C-6529C TYPE3285Royco 586L&M5GAL/PAIL MIL-PRF-6086E L&M286Royco 6341GAL/CAN MIL-PRF-63460287Royco 7175GAL/PAIL MIL-PRF-17111288Royco 7561GAL/CAN MIL-PRF-5606H289Royco 7561QT/CAN MIL-PRF-5606H290Royco 7571LB/CAN291Royco 7775GAL/PAIL MIL-PRF-87257292Royco 7821GAL/CAN MIL-PRF-83282293Royco 7821QT/CAN MIL-PRF-83282294Royco 78355GAL/DRUM MIL-PRF-6083F295Royco 8081QT/CAN MIL-PRF-7808296Royco 8851GAL/CAN MIL-PRF-6085D297Royco 89924X1QT/CTN MIL-PRF-23699F C/I298Royco 8995GAL/PAIL MIL-PRF-23699F C/I299Royco 9505GAL/PAIL MIL-PRF-7024E TYPE 2300Royco C-201 1.75LB/CAN301Royco HF-825 1.75LB/CAN PWA35600302Royco LGF5GAL/PAIL BMS3-32 TYPE2303Royco SSF5GAL/PAIL BMS3-32 TYPE1304PS 5011PT/KIT305PS 870A1/21PT/KIT MIL-PRF-81733 TYPE1 CLA306PS 870A21PT/KIT MIL-PRF-81733 TY1PE CLA307PS 870B1/26OZ/SK MIL-PRF-81733 TYPE II308PS 870B1/21PT/KIT MIL-PRF-81733 TYPE II309PS 870B26OZ/SK MIL-S-81733 TYII310PS 870B21PT/KIT MIL-S-81733 TYII311PS 870C12/206OZ/SK MIL-PRF-81733 TYPE IV12 CL1 GR A 312PS 875B1/26OZ/SK 313PS 875B1/21PT/KIT314PS 875B26OZ/SK BMS5-142315PS 875B21PT/KIT BMS5-142316PS 890A1/26OZ/SK MIL-S-8802 TYPE II317PS 890A1/21PT/KIT MIL-S-8802 TYPE II318PS 890A21PT/KIT MIL-S-8802F TYPE II CLA321PS 890B1/21PT/KIT MIL-S-8802F TYPE I322PS 890B26OZ/SK MIL-S-8802F TYPE II323PS 890B21PT/KIT MIL-S-8802F TYPE II324PS 895B26OZ/SK325PR 1435L/CAN326PR 1482OZ/KIT327PR 4207OZ/KIT328PR 42014OZ/KIT329PR 8926OZ/SK330PR 1005L500ML/KIT331PR 1198 1.8L/KIT332PR 1422A1/26OZ/SK CML09-013333PR 1422A1/21PT/KIT CML09-013334PR 1422A26OZ/SK CML09-013C, MIL-S-8802 TYPE I335PR 1422B1/26OZ/SK336PR 1422B1/21PT/KIT337PR 1422B26OZ/SK338PR 1422B21PT/KIT339PR 1425B26OZ/SK340PR 1428A1/26OZ/SK MIL-S-8784341PR 1428A26OZ/SK MIl-S-8784A ,BMS5-37342PR 1428B1/26OZ/SK343PR 1428 B26OZ/SK Mil-S-8784,BMS5-37344PR 1428 B21PT/KIT Mil-S-8784,BMS5-37345PR 1432GP1PT/KIT BMS5-95KTY1 CLASSF-1346PR 1436GA6OZ/SK CML09-013,MIL-PRF-81733, TY I, CL A 347PR 1436GA1/2130ML/KIT 348PR 1436GA1/26OZ/SK349PR 1436GA26OZ/SK350PR 1436GB6OZ/SK351PR 1436GB1/26OZ/SK352PR 1436GB1/2150ML/KIT353PR 1436GB1/2500ML/KIT354PR 1436GB26OZ/KIT357PR 1436G Sprayable1PT/KIT358PR 1750A26OZ/SK359PR 1750B26OZ/SK AMS3276 CLB360PR 1750B21PT/KIT AMS3276 CLB361PR 1764B26OZ/SK362PR 1770B21PT/KIT363PR 1771B2100ML/EA364PR 1773A2100ML/EA365PR 1773A26OZ/SK366PR 1773B26OZ/SK367PR 1775B26OZ/SK368PR 1776B1/26OZ/SK369PR 1776B26OZ/SK370PR 1776MB26OZ/SK371PR 1826A1/26OZ/SK372PR 1826B1/46OZ/SK373PR 1826B1/26OZ/SK AMS3277374PR 1828B1/26OZ/SK MIL-S-83430 AMS3277,TYII 375Mastinox 6856H160ML/EA376Mastinox 6856K160ML/EA MIL-P-8116B,BMS3-27A 377Mastinox D40160ML/EA CML05-047378ALK-6005GAL/PAIL MIL-C-87936379ACT 655L/CAN380ACT 1435L/CAN381PR 1435L/CAN382ACT 1435L/CAN383T175L/CAN384CV1165L/CAN385ACT 345L/CAN386ACT 655L/CAN387ACT 685L/CAN388ACT 855L/CAN389FE 85M5L/CAN390T1155L/CAN391FE1075L/CAN392T1155L/CAN393EC75/C66155L/CAN394EC75/802 MSRR90645L/CAN395EC75/TN1865L/PAIL396512X310/910X5331GAL/KIT397512X310/910X3771GAL/KIT398513X390/910X6241GAL/KIT399513X377/910X4822GAL/KIT400513X377/910X482/020X364 2 GAL/KIT401513X384/910X456 2 GAL/KIT402513K009 2 GAL/KIT403515K011/910-012 2 GAL/KIT BMS10-11 TYPE1 404515X349/910X533 2 GAL/KIT405528X306/910X4642QT/KIT406528X310/910X4642GAL/KIT407528X30682QT/CAN408IP9064/00005L/CAN409IP9064/63621L/CAN4104125/2047 BAC707 GREY4L/CAN4114125/6407 BLUECELOMER VARNISH4L/CAN4124355/3600 PRIMER PAC33 GREEN5L/CAN CML16-001C 4134360/30315L/CAN CML16-001C 4140701/9000 HARDENER1L/CAN CML16-001C 4150433/9000 THINNER5L/CAN CML16-001C 4168500/52005L/CAN4170613/9000 Hardener2L/CAN4180580/9000 THINNER5L/CAN4195425/0000+0707/9000+0491/90006L/KIT420 5420/2620 Base3L/CAN4210707/9000 Hardener1L/CAN4220491/9000 Thinner5L/CAN423CELOMER5014,5425/0000+0707/9000+0491/900010L/KIT424F5664200+N39/1327+N39/346011L/KIT 425P-9915L/KIT 426CA72332GAL/KIT 427CA8000/B7011GAL/KIT428CA8000/BAC7071GAL/KIT 429CA8000/B900A3GAL/KIT 430CA8000/B16101GAL/KIT 431CA8000/B57734GAL/KIT 432CA8000/BAC70671GAL/KIT 433CA8000/B708461GAL/KIT 434CA8000B1GAL/KIT 435CA8000C1GAL/KIT436CA8000C11GAL/KIT 437CA8000C21GAL/KIT 438CA8000C31GAL/KIT 439CA8001/B0900C5L/CAN440CA77002GAL/KIT 441CA8100/B7074GAL/KIT 442CA8100/70674GAL/KIT 443CA8800/B7014GAL/KIT444CA8800/B7074GAL/KIT 445CA8800/Y60091GAL/CAN 446CA8800/Y60111GAL/CAN 447CA8800/B708461GAL/CAN 448CA8800CT11GAL/CAN 449CA8800Z1GAL/CAN 450Desoclean 45(020X413)1GAL/CAN451EWDY048A/B1GAL/KIT MIL-PRF-85582 Type I, PWA 36519-2 452RTV 601PT/KIT453RTV 881PT/KIT454RTV 881LB/KIT455RTV 102 2.8OZ/EA CP2266456RTV 103 2.8OZ/EA457RTV 106 2.8OZ/EA COMAT08-013458RTV 10610.1OZ/EA COMAT08-013459RTV 108 2.8OZ/EA460RTV 11610.1OZ/EA461RTV 118 2.8OZ/EA462RTV 12810.1OZ/EA463RTV 13310.1OZ/EA464RTV 147A/B 1.1KG/KIT CP2297, CP2298465RTV 157 2.8OZ/EA466RTV 159 2.8OZ/EA467RTV 159 5.4OZ/EA468RTV 162 2.8OZ/EA469RTV 16210.1OZ/CAN470RTV 167 2.8OZ/EA471RTV 6301LB/KIT472RTV 6702300ML/EA473RTV 99101PT/CAN474SS 4004 P1PT/CAN475SS 4044 P1PT/CAN476SS 41551PT/CAN477Q4554 GE Light EA478PSA 52940LB/CAN BAC5010 TY77479SRC 18 1.9LB/CAN BAC5010 TY77480DC 4150G/EA481DC 4 3.6KG/PAIL482DC 4199.5KG/DR483Molykote 331KG/CAN484Molykote 33 M 5.3OZ/EA485Molykote 33 M100G/EA486Molykote 33 L 5.3OZ/EA487Molykote P-37453G/EA COMAT10-129 488Molykote P-37500G/EA COMAT10-129 489DC 44M150G/EA490DC 44M1KG/CAN491DC 55 M Grease100G/EA492DC 55 M Grease1KG/CAN493Molykote M 77500G/CAN494Molykote M 772KG/CAN495Molykote 106500G/CAN496Molykote 1065KG/PAIL497Molykote 1064L/CAN498DC 111100G/EA499DC 111150G/EA500DC 111 3.6KG/CAN501DC 170A/B22LB/KIT502DC 20018KG/PAIL503DC 321312G/EA504Molykote D 321R400ML/EA505Molykote D 321R1KG/CAN506DC 340142G/EA507DC 3409KG/PAIL508DC 510(500CS) 3.6KG/CAN509DC 510(500CS)500ML/EA510DC 5271KG/CAN511DC SYLGARD 57712.1LB/CAN512DC 730 WHITE90ML/EA513DC 732 BLACK3OZ/EA514DC 732 BLACK300ML/EA515DC 732 Aluminium90ML/EA516DC 732 Aluminium139ML/EA517DC 732 CLEAR90ML/EA518DC 732 CLEAR139ML/EA519DC 732 CLEAR300ML/EA520DC732 WHITE90ML/EA521DC732 WHITE300ML/EA522DC 733 Clear300ML/EA523DC 734 Clear3OZ/EA524DC 736300ML/EA525DC 737 Clear300ML/EA526RTV 738 Clear310ML/EA527RTV 738 White90ML/EA528DC 780300ML/EA529DC 786 WHITE300ML/EA530Molykote 1000400ML/EA531DC 1200 CLEAR309G/EA532DC 1200 RED309G/EA533DC 1201348G/EA534DC 1204309G/EA535DC 1205348G/EA536DC 31101LB/CAN537DC 31104KG/PAIL538DC 31201LB/CAN539DC 31205KG/PAIL540Catalyst S409G/EA541DC 3140 Clear493G/EA MIL-A-46146 542DC 3140 Clear90ML/EA MIL-A-46146 543Dow Corning HVG150G/EA 544Dow Corning HVG 3.6KG/PAIL545RTV 3145 GRAY3OZ/EA546RTV 3145 GRAY305ML/EA547RTV 3145 CLEAR3OZ/EA548RTV 3145 CLEAR305ML/EA549Molykote 3400A500G/EA550Molykote 3400A1KG/CAN551Molykote 3402C500G/EA Mil-L-23398D 552DC 7091 white310ML/EA553RTV 98910.05LB/EA MIL-S-23586 TY1 554Molykote Gn Paste1KG/CAN555Molykote G-N PLUS Paste100G/EA CP2444556Molykote G-N PLUS Paste312G/EA CP2444557Molykote G-N PLUS Paste1KG/CAN CP2444558Molykote G-n Metal Assembly312G/EA CP2569559Molykote G-n Metal Assembly500G/EA CP2569560Molykote G-Rapid Plus Paste400ML/EA561Molykote G-Rapid Plus Paste1KG/CAN562Molykote U-N paste1KG/CAN CP2171563Molykote Microsize Powder1KG/CAN564Molykote Supergliss400ML/EA565Molykote DX50G/EA566Molykote DX1KG/CAN567DC 3-6548A/B36.2KG/KIT568DC3-68918LB/CAN569DC 90-006-21LB/KIT570DC 90-006- 1/21LB/KIT571DC93-076-1/21LB/KIT572DC93-076-21LB/KIT573DC 93-006-11LB/KIT574DC93-006-61LB/KIT575PD-9101LG/CAN576PG-6631LG/CAN577P5200340G/EA578LOC 388075ML/EA579DC F CATALYST45G/EA580DC 1-257718.1KG/PAIL581Dow corning BR2400G/EA5823M Scotch Grip 101QT/CAN5833M 86A CLEAR1PT/CAN5843M DP100 Clear/Translucent50ML/EA5853M DP110 Clear/Translucent50ML/EA5863M DP190 GRAY2OZ/EA5873M DP8005 Black12X35ML/CTN5883M Roto Peen Flap Assembly TC 330 I 9/16" X 1"/SH5893M Roto Peen Flap Assembly TC 330 II9/16" X 1.25"/SH 5903M Roto Peen Flap Assembly TC 330 III1" X 2"/SH5913M Petroleum Sorbent Pad T-15117"x19"/PAD5923M EC7761QT/CAN MIL-D-17951E 5933M EC 8471QT/CAN 5943M EC 8475GAL/PAIL5953M Scotch-Weld E110020G/EA5963M EC12525OZ/KIT5973M EC1300L1QT/KIT5983M EC1300L1GAL/KIT5993M SG13571QT/KIT6003M SG13575GAL/PAIL6013M EC1751A/B2OZ/KIT6023M EC1838 B/A1QT/KIT6033M EC18701GAL/CAN6043M EC2216 B/A2PT/KIT BMS5-92 TYPE I 6053M EC2216 B/A2QT/KIT BMS5-92 TYPE I 6063M EC22621QT/KIT 6073M EC2615A/B 1.25OZ/KIT6083M EC2615A/B1QT/KIT6093M EC2616B/A1QT/KIT6103M EC3333 1.25OZ/KIT6113M EC3524B/A1GAL/KIT6123M EC3532B/A2OZ/KIT6133M EC3532B/A1QT/KIT6143M EC3549B/A2OZ/KIT6153M EC3587B/A1QT/KIT6163M EC3901 Red1/2PT/KIT6173M EC39601GAL/KIT6183M 4150S8OZ/CAN6193M EC44195GAL/PAIL6203M EC46931QT/KIT6213M EC46931GAL/CAN6223M CITRUS BASE IDUSTRIAL CLEAER5OZ/EA6233M CITRUS BASE IDUSTRIAL CLEAER18.5OZ/EA6243M Scotch 271"X60YD/RL6253M 480.25"X260"/RL6263M 480.5"X260"/RL6273M 601"X36YD/RL6283M 611"X36YD/RL6293M 691"X36YD/RL MIL-I-19166 6303M 692"X36YD/RL MIL-I-19166 6313M Scotch 701"X10YD/RL6323M 74489G/CAN6333M Super 77467G/CAN6343M Scotch 791"X60YD/RL6353M 2021"X60YD/RL6363M 2022"X60YD/RL6373M 2151"X60YD/RL6383M 2152"X60YD/RL6393M 218 GREEN1"X60YD/RL6403M 23124MMX55M/RL6413M 23148MMX55M/RL6423M 2321/4"X60YD/RL6433M 2321/2"X60YD/RL6443M 2321"X60YD/RL6453M 232 1.5"X60YD/RL6463M 2322"X60YD/RL6473M 2323"X60YD/RL6483M 2341"X60YD/RL6493M 2441"X55YD/RL6503M 2501"X60YD/RL序号品名包装标准规范6513M 2502"X60YD/RL6523M 3611"X60YD/RL6533M 3612"X60YD/RL6543M 3631"X36YD/RL6553M 3632"X36YD/RL6563M 398FR2"X36YD/RL6573M 398FR3"X36YD/RL6583M 398FR4"X36YD/RL6593M 4201/2"X36YD/RL6603M 4203/4"X36YD/RL6613M 4211"X36YD/RL6623M 4212"X36YD/RL6633M 4251/2"X60YD/RL CP2517, CML08-052 6643M 4251"X60YD/RL CP2517, CML08-052 6653M 4252"X60YD/RL CP2517, CML08-052 6663M 4253"X60YD/RL CP2517, CML08-052 6673M 4254"X60YD/RL CP2517, CML08-052 6683M 4271"X60YD/RL6693M 4272"X60YD/RL6703M 4274"X60YD/RL6713M 42712"X60YD/RL6723M 42724"X60YD/RL6733M 4341"X60YD/RL6743M 4342"X60YD/RL6753M 4343"X60YD/RL6763M 4352"X36YD/RL6773M 4361"X36YD/RL6783M 4362"X36YD/RL6793M 467MP2"X60YD/RL6803M 467MP48"X60YD/RL6813M 468MP12"X60YD/RL6823M 468MP1"X60YD/RL6833M 468MP4"X60YD/RL6843M 4703/4"X36YD/RL6853M 4701"X36YD/RL6863M 4701"X36YD/RL6873M 471 Yellow/Black1"X36YD/RL 6883M 471 Yellow/Black2"X36YD/RL 6893M 471 Yellow/Black3"X36YD/RL 6903M 471 Yellow/Black4"X36YD/RL 6913M 471 Yellow/Black6"X36YD/RL 6923M 6001"X72YD/RL6933M 6701"X72YD/RL6943M 850 Black1"X72YD/RL6953M 851 Green1"X72YD/RL 6963M 851 Green2"X72YD/RL 6973M 9501"X60YD/RL6983M 9502"X60YD/RL6993M 95024"X60YD/RL7003M 95048"X60YD/RL7013M 1500 Black18MMx10M/RL 7023M 214248"X55YD/RL7033M 221431"X55YD/RL7043M 23071"X60YD/RL7053M 23072"X60YD/RL7063M 230824MMX55M/RL7073M 230848MMX55M/RL7083M 2310750MMX55M/RL7093M SJ3518 Black1"X50YD/RL 7103M SJ3518 Black2"X50YD/RL 7113M SJ3519 Black1"X50YD/RL 7123M SJ3519 Black2"X50YD/RL 7133M SJ3526 Hook Black2"X50YD/RL 7143M SJ3527 Loop Black2"X50YD/RL 7153M 49301"X72YD/RL7163M 493024"X72YD/RL7173M 49501"X36YD/RL7183M 495012"X36YD/RL7193M SJ5916 4.5"X36YD/RL7203M SJ59169"X36YD/RL7213M SJ8665 FP1-1PC7223M SJ8665 FP22PC7233M SJ8665 FP33-1PC7243M SJ8665 FP110PC7253M 403224.5"X36YD/RL7263M 4737T2"X36YD/RL7273M 4737T23.5"X36YD/RL7283M 49451/2"X36YD/RL7293M 49451"X36YD/RL7303M 494524"X36YD/RL7313M 495224"X36YD/RL7323M 5354 Black3/4"X1/8" X 50 '/RL 7333M Scotch 54131"X36YD/RL7343M Scotch 541324"X36YD/RL 7353M 54901"X36YD/RL7363M 6969(BLACK) 1.89"X60YD/RL 7373M 744720PAD/BOX7383M 84121"X72YD/RL7393M 86633"X36YD/RL7403M 86634"X36YD/RL7413M 866336"X36YD/RL7423M 8663 DL Clear36"X36YD/RL 7433M 86712"X36YD/RL7443M 86713"X36YD/RL7453M 86714"X36YD/RL7463M 86715"X36YD/RL7473M 86716"X36YD/RL7483M PPT 8672 Clear6"X36YD/RL 7493M 86863"X36YD/RL7503M 89513/4"X72YD/RL7513M 94481"X36YD/RL7523M 94482"X36YD/RL7533M 94731"X60YD/RL7543M 94734"X60YD/RL7553M 9495LE48"X60YD/RL 7563M 971312"X36YD/RL7573M 9742 Nozzle EA7583M 048011-055282"/DISC 7593M 048011-055323"/DISC760AV 813.5OZ/CAN761AV 2513.5OZ/CAN762AV 3013.5OZ/CAN763D-5015NS12OZ/⽀764D-5026NS12OZ/⽀765D-5035NS12OZ/⽀766D-5261NS12x12OZ/CTN767D-5263NS12OZ/⽀768D-5460NS12OZ/CAN769D-5665NS12x12OZ/CTN770Cor-Ban 27L12X5.8OZ/CTN 771Cor-Ban 27L1QT/KIT772Cor-Ban 3512X12OZ/CTN773ZIP CHEM D-560012OZ/⽀774ZIP CHEM D-56005GAL/PAIL 775 ZIP CHEM C8005GAL/PAIL777 X-40512OZ/EA778Dapco 18-4F1PT/KIT779Dapco 18-4F1QT/KIT780 Dapco 21006OZ/EA CML09-023 781DAPCO 22006OZ/KIT 782DAPCO1-1004OZ/KIT783Epibond 156A/B6X1QT/CTN784EPOCAST 50A1/98161GAL/KIT785Epocast 50A1/9461QT/KIT786Epocast 1511A/B1QT/KIT787EPIBOND 1534A/B1QT/KIT788EPIBOND 1536A/B1QT/KIT789EPOCAST 1617A/B1QT/KIT790Epocast 1618D/B1GAL/KIT791Epocast 1618D/B6OZ/EA792Epocast 1619 1.3LB/KIT793Epocast 16361QT/Kit794EPOCAST 87005A-B801QT/KIT795AV138M/HV998 1.4KG/KIT796ARALDITE AV 138M 1.0KG/CAN797ARALDITE HV 9980.4KG/CAN798Araldite SV4091KG/CAN799AY103/HY9912KG/KIT800AY103-1/HY991 1.4KG/KIT801LY560 1.0KG/CAN802HY5600.25KG/CAN803AF3024 1.27X560X300MM/SH804AV121N-11KG/KIT805HY951500G/CAN806MY7501KG/CAN807EY30096OZ/EA808AW134+HY994 1.40KG/KIT809ARALDITE AW 134 2B1KG/CAN810ARALDITE HY 9940.4KG/CAN811AV144-21KG/CAN813N39-1794500ML/CAN814Araldite 420A/B 1.4KG/KIT815Araldite 2011 (AW106/HV953U)50ML/KIT816Araldite 2011 (AW106/HV953U)200ML/KIT817Araldite 2011 (AW106/HV953U) 1.8KG/KIT818Araldite 2012 (AW2104+HY2934)4KG/KIT819Araldite 2015 (AV5308+HY5309-1)2KG/KIT820ARALDITE LY 50521KG/CAN821ARADUR 5052 CH0.75KG/CAN822Renlease QZ-51110.75KG/CAN CML05-013A823Renlease QV51101KG/CAN824Uralane 5772A/B6X1QT/CTN DPM 6087; GD 0-73668 TY 1 CL 1 Rev G 825URALANE 5774A/C1QT/KIT 826NASM/MS20995C151LB/RL827NASM/MS20995C201LB/RL828NASM/MS20995C251LB/RL829NASM/MS20995C281LB/RL830NASM/MS20995C301LB/RL831NASM/MS20995C321LB/RL832NASM/MS20995C411LB/RL833MS20995CY201LB/RL834MS20995CY151LB/RL835MS20995NC201LB/RL836MS20995NC321LB/RL837MS20995NC511LB/RL838MS20995N201LB/RL839MS20995N321LB/RL840MS21043-4EA841MS24665-302EA842MS24665-151EA843MS24665-172EA844MS9966-10EA845AS3578-266EA846MS9226-021LB/RL847MS9226-031LB/RL849MS28774-012EA850FM300-2U 0.03 PSF 500 SF/RL851ABS5006-2D2MMX25MMX15M/RL CML08-005C852ABS5006-4D 4MMX25MMX10M/RL CML08-005C ，BMS1-68 Form III 853ABS5006-4F 38MMX4MMX20M/RL CML08-005C 854ABS5006-6A 6MMX9MMX10M/RL CML08-005855ABS5006-6J6MMX200MMX10M/RL 856HCS2101-04-5ML 0.005"X54"X254YD/RL 857HCS2101-04-60V 0.002"X60"X333YD/RL858HCS2102-0460"X100YD/RL 859HCS2102-1060"X50YD/RL 860HCS2103-P 36"X100YD/RL 861HCS2108-P48"X200YD/RL 862HCS2108-NP 48"X200YD/RL 863HCS211246"X300YD/RL 864HCS21141"X72YD/RL865HCS21251/8"X1/2"X25'/RL 866HCS2201 Cab-O-Sil 1GAL/CAN 867HCS22021GAL/CAN 868HCS2202-01 BJO-09301GAL/CAN 869HCS2401-010-0538"X5YD/RL BMS8-79 Class III, Style120870HCS2401-02038"X5YD/RL BMS8-79 Style 1581 Class III 871HCS2401-030-0538"X5YD/RL BMS8-79 CL III STY 7781 REV AE 872HCS2401-030-1038" X 10YD/RL BMS8-79 CL III STY 7781 REV AE 873HCS2401-04038"X120YD/RL BMS8-139 Class 1, Style 120874HCS2401-040-05 38"X5YD/RL BMS8-139 CL 1 STY 120 REV L 875HCS2401-050 38"X60YD/RL BMS8-139 Class 1, Style 1581876HCS2401-050-05 38"X5YD/RL BMS8-139 CL 1 STY 1581 REV L877HCS2401-060-0538"X5YD/RL BMS8-139 CL 1&2 STYLE 7781 REV K878HCS2402-010-0542"X5YD/RL BMS8-168 Style 3K-70-PW , TYPE II & III, CL2879HCS2402-020-0542"X5YD/RL BMS8-212, 3K-70-PWTYIV CL2, REV P 880HCS2402-020-1042"X10YD/RL BMS8-212 3K-70-PW, TYPE IV, CL 2, REV P881HCS2402-030-0542"X5YD/RL BMS8-212 TYPE III, CL 2, REV P COMAT08-059,3K-135-8H882HCS2402-040-05 42"X5YD/RL BMS8-256 Style 3K-70-PW, TYPE IV, CL 2, REV K 883HCS2402-05060"X80YD/RL BMS8-297 Style 3K-70-PW TYPE IV, CL 2884HCS2402-050-0560"X5YD/RL BMS8-297 3K-70-PW , TYPE IV, CL 2885HCS2404-010-0536"X5YD/RL BMS5-101 GR10 KNIT, TYII .06 WT, KNIT SUPPORT CARRIER,BMS5-129 TY4 CL2D GR10 REV L 886HCS2404-03036"X36YD/RL BMS5-129 CLIIA GR5 TY2 WT .03, LOW TACK887HCS2404-040-0536"X5YD/RL BMS5-129 TY II, CL IIB GR10 TY2 WT .06, LOW TACK 888HCS2404-05036"X5YD/RL BMS5-154 Type II Class1&2 Grade 5889HCS2404-050-0536"X5YD/RL ADHESIVE FILM, BMS5-154 TYII CL1&2 GR 5 (WT .05),REV D890HCS2405-0100.050"X1"X25'/RL BMS5-90 TYIII CL1 GR50CORE SPLICE ADHESIVE FOAM 891HCS2406-011 BR1271QT/CAN BMS5-89 TY1 GR A REV R 892HCS2406-011BR1271GAL/CAN BMS5-89 TY1 GR A REV R893HCS2409-01042"X5YD/RL BMS9-8 TYI CL2 GR3 STY3K-135-8H894HCS2409-02042"X5YD/RL BMS9-8 TYI CL2 GR3 STY 3K-70-PW REV K FL1 -CLASS 3 IS ALLOWED WHERE CLASS 2 IS SPECIFIED895HCS2410-01038"X250YD/RL BMS9-3 TYD CL7 ST120, AMS-C-9084 TYIII CL 1&2896HCS2410-02038"X125YD/RL BMS9-3 TYH2 CL7 ST1581 DRY FABRIC, VOLAN BMS9-3 REV R, AMS-C-9084 TY VIII-A CL1&2897HCS2410-03038"X125YD/RL BMS9-3 TYH3 CL7 ST7781, BMS9-3 REV R, AMS-C-9084 TY VIII-B CL 1&2898HCS2410-04038"X125YD/RL BMS9-3 Type H-3 Class 13 Style 7781899Honeycomb 3"X48"X100"/RL BMS4-4, TYPE 3-10N, FORM B EXPANDED PANEL 3.1 3/16 .001N 5052900Aerodur Finish SGL。
封装及命名规则
Q PLCC (塑料式引线芯片承载封装) R 窄体陶瓷双列直插封装(300mil) S 小外型封装 T TO5,TO-99,TO-100 U TSSOP,μMAX,SOT W 宽体小外型封装（300mil） X SC-70（3 脚，5 脚，6 脚） Y 窄体铜顶封装 Z TO-92MQUAD /D 裸片 /PR 增强型塑封 /W 晶圆
K -- 下冲-保护电路 (CBTK)
R -- 输入/输出阻尼电阻 (LVCR)
S -- 肖特基钳位二极管 (CBTS)
Z -- 上电三态 (LVCZ)
5. 位宽
空 = 门、MSI 和八进制
1G -- 单门
8 -- 八进制 IEEE 1149.1 (JTAG)
16 -- Widebus™（16 位、18 位和 20 位）
MPY 乘法器 OPA 运算放大器 PCM 音频和数字信号处理的 A/D 和 D/A 转换器 PGA 可编程控增益放大器 SHC 采样/保持电路 SDM 系统数据模块 VFC V/F、F/V 变换器 XTR 信号调理器
2． 器件型号
3． 一般说明： A 改进参数性能 Z + 12V 电源工作
L 锁定 HT 宽温度范围
3．产品等级：由 A、B、C、D 四类组成，A 档最高，依此 B、C、D 档
4 ．温度范围： C= 0℃ 至 70℃（商业级） I =-20℃ 至 +85℃（工业级） E =-40℃ 至 +85℃（扩展工业级） A = -40℃至+85℃（航空级） M =-55℃ 至 +125℃（军品级）
5．封装形式：
A SSOP(缩小外型封装) B CERQUAD C TO-220, TQFP(薄型四方扁平封装) D 陶瓷铜顶封装 E 四分之一大的小外型封装 F 陶瓷扁平封装 H 模块封装, SBGA J CERDIP (陶瓷双列直插) K TO-3 塑料接脚栅格阵列 LLCC (无引线芯片承载封装) M MQFP (公制四方扁平封装) N 窄体塑封双列直插 P 塑封双列直插
MSD(湿敏器件防护)控制技术要求规范
1、简介：SMD器件的出现直接带来了新的挑战，而这些挑战的重心又在于包装的品质和可靠性，周围环境中的湿气会通过包装材料渗透到包装内部，并在不同材料的表面聚结。
在组装工艺中，SMD元件贴装在PCB上时会经历超过200℃，在焊接时，湿气的膨胀会造成一系列的品质问题。
本规范遵照IPC/JEDEC有关的潮敏标准拟制，主要体现潮湿敏感器件在公司控制处理各环节的规范性要求。
本规范由塑封器件潮湿敏感定义、潮湿敏感器件分级要求、潮湿敏感器件包装要求、潮湿敏感器件干燥要求、潮湿敏感器件使用及注意事项等内容组成。
2、目的：为改进MSD控制水平，有效提高产品质量和可靠性，同时提高技术人员对潮敏器件的认识水平，规范研发、市场和生产阶段对易潮敏器件的正确处理。
3、范围：本规范规定了潮湿敏感器件等级要求、包装要求、操作及处理方法等方面的技术指标和控制措施。
本规范适用于步步高教育电子有限公司各类潮湿敏感器件（以下简称MSD）验收、储存、配送、组装等过程中的管理。
供应商和外协厂商均可以参照本规范执行。
4、职责：4.1 供应资源开发部负责湿度敏感器件的采购。
4.2 材料技术部负责提供湿度敏感器件的规格书。
4.3 工艺工程部负责湿度敏感器件的管控方案制定和外协生产MSD使用指导。
4.4 物流管理部仓储科负责对湿度敏感器件的储存（原包装密封储存、再次真空包装储存、干燥短期储存）。
4.5 品质部负责湿度敏感器件的来料检验和现场使用监督以及使用异常的反馈。
4.6 生管部（含SMT外协厂商）负责湿度敏感器件的使用以及车间使用寿命的控制。
5、关键词：潮湿敏感、MSD、MSL、温度、相对湿度、干燥、烘烤、MBB6、规范引用的文件：7、术语和定义：➢PSMD（Plastic Surface Mount Device）：塑料封装表面安装器件。
➢MSD（Moisture Sensitive Device）：潮湿敏感器件。
指非气密性封装的表面安装器件。
American 光学元件表面光洁度标准资料
左图是大家看的编号2的样品（图 片是放大的不是实际尺寸） 图中的划痕为20#，且长度>1/4D。 对于表面质量要求20-10该产品不 合格。但本次样品未提出表面质量 要求，而是要大家自已决定光洁度 等级。因此该产品划痕可判为40#。
6
3.当元件存在最大划痕，而最大划痕的长度之和未超过1/4D，要求所有 级数的划痕乘以划痕长度与元件直径之比所得乘积之和，不得超过最大 划痕级数的一半。
7
如左图所示的产品 则20#划痕长度0.7mm。10#划痕 长度2mm对于表面质量要求20-10 该产品最大划痕长度1mm<1/5。
所有级数的划痕乘以划痕长度与元件 直径之比所得乘积之和为： 20 ×0.7/5+10 ×2/5=2.8+2=4.8<10， 该元件划痕可判为20#
10# 20#
8
4.当元件的划痕级数未超过表面质量要求的级数，且元件不存在最大 划痕时，所有级数的划痕乘以划痕长度与元件直径之比所得乘积之和， 不得超过最大划痕级数。
例： 40mm×40mm的元件，质量指标要求为60-40，其中一个20mm 的区域有40#点子一个，20#点子一个，10#点子一个，同时在另一 个20mm区域中，20#点子2个，10#点子4个，5#点子1个。
A区的麻点直径的和: =40+20+10=70 < 40×2=80 B区的麻点直径的和: =20×2+10×4+5×1=85> 80， B区不合格。 因此元件不合格。
6. 当出现如图所示密集麻点时以麻点聚集的外围圈径为麻点大小。
以图中外圆为麻点大小，如果超过表面质量要求 则该元件不合格。
光洁度写成两位数据形式时必须按标准写，如产品点子判 为0#，但划痕判为40#，则产品光洁度为40-20而不是40-0。 如果产品点子判为20#而划痕判为0#，则产品光洁度为40-20 而不是0-20。