谱瑞特智能排孔系统 V1.02手册
PECO Series PEACH GEMINI PuraSep 水平气体过滤器-煤炭聚集器说明书
A. GENERAL DATAThe PEACH Gemini PuraSep is a two stage filter-coalescer used for removing solids and liquids from a natural gas stream. The uniqueness of this design is centered around one replaceable cartridge that acts as both the primary and secondary stage, with a cartridge support plate separating the two stages. This provides dual stage coalescing. The 2nd stage portion of the cartridge is contained inside a Liquid Impingement Baffle (LIB). This LIB is a stainless steel liquid cylinder placed in the 2nd stage of the vessel. If it becomes plugged, it is easily removed from the 1st stage of the vessel through the cartridge support plate. It can then be cleaned and/or replaced.Access to the cartridges is through a full end Quick Opening Closure located at the inlet end of the vessel.The PEACH Gemini PuraSep ® has an upper and lower chamber; each chamber has two compartments. Theupper chamber provides the filtration-coalescer-separation of the solids and liquids, while the lower chamber collects the liquid. Some of the solids will drain into the lowerchamber below the first stage, but most of the solids collect on the cartridges and on the bottom of the first stage upper chamber. The PGCPH provides removal of 99.9% of all solids particles and 99.5% of all liquid particles 0.3 micron and larger with a 100% turndown ratio (with use of PL -01 performance level series PGC cartridges).1st Stage SumpInletSump Divider Plate 2nd Stage SumpOutlet2nd StageFilter/Coalescer CartridgesLiquid Impingement Baffle (LIB)Full EndQuick Opening ClosurePipe Risers1st StageCartridgesB. GENERAL ARRANGEMENT / FLOW1. P osition the filter vessel on a flat surface and ensure there is adequate space in front of the closure to allow room to install/ remove cartridges and above the closure for venting.2. C onnect inlet and outlet connections of filter vessel to piping of equal diameter. Check the filter vessel drawing to identify the location of each. It is recommended that the filter vessel be installed with by-pass and block valves to permit continued operation during cartridge changes.Check to ensure that all blind flangebolting is properly torqued. Flange boltingis torqued at the factory, however mayrelax or loosen during shipment to theinstallation site.3. C lose inlet and outlet connection valves.4. O pen the vent valve.5. T he blow-down connection should be valved and piped to a pit, tank, or blow-down system.6. I nstall any auxiliary equipment as required, suchas differential pressure gauge and liquid levelcontrols/drains. Since the vessel has two separate compartments, two sets of liquid control equipment are necessary. The controls must be piped independently and not be manifolded between the first stage compartment and second stage compartment because of the pressure differential between the two stages.7. T wo pressure taps are furnished on the vessel. Oneis located in the first stage, the other in the second stage is between the cartridge support plate and the outlet nozzle. It is extremely important that an accurate differential pressure gauge be installed on the vessel. Pressure drop is the only indicator that the operator has to tell him/ her when the filter vessel should be blown-down or by-passed to change the filter cartridges.8. O pen the filter vessel closure (according to closure manufacturer’s procedures) and inspect theinside of the vessel. Verify the internals have not been damaged and that the O-ring for the closure is in place. Verify the cartridges are seated properly on the risers and that each cartridge seal is fully engaged. 9. C artridge installation:This particular series uses PGC cartridges which provides for Tool-Less cartridge change-outs. This design offers many benefits including:• no tools required to secure/change cartridges• s tate-of-the-art pressure loading enhancementseal to prevent gas bypass• minimizes maintenance time and cost10. I nspect the closure gasket to make sure it is new andin good condition. Make sure it is seated in the closure groove correctly.11. C lose the closure (according to closuremanufacturer’s procedures).12. P rior to filling the filter vessel with gas, verify that theoperating pressure and temperature are within thedesign limits of the filter vessel. The design conditions can be found on the filter vessel nameplate.13. R eview and follow all operating company safetyprocedures for filter operation.14. F ollow all operating company safety and lockout/tag-out procedures.15. V erify that inlet and outlet connection valves are closedand that vent valve is open.16. S lowly and partially open the inlet connection valve andintroduce the gas stream into the filter vessel. Allowgas to purge air from the filter vessel through the vent valve. Purging should only take a few seconds.17. Close vent valve.18. C heck for leaks. Should a leak occur, close inlet valveimmediately and determine cause of leak.Make sure to fully depressurize the vesselprior to attempting to fix the leak.19. O nce no leaks are found, check to be sure that allauxiliary equipment is ready for operation.*Pressure gauge, liquid level controls and automaticdump valves are optional features that can be supplied by the manufacturer or can be purchased separatelyby the end user.C. INSTALLATION INSTRUCTIONS21. O nce the filter vessel is full of gas and no leaks are found, open the inlet valve all the way.2. S lowly open the outlet connection valve and begin flow through vessel. Flow should be set based on recommended flow rate provided during sizing.3. M onitor differential pressure across the inlet/outlet. The filter is typically designed for 2 psid (0.14 bar) or less differential pressure at start-up at normal operating conditions. Once the cartridge becomes wet/ saturated, the differential pressure may increase slightly. The cartridges have to become completely saturated before stripping liquid. This may take 24 hours or longer, depending on the amount of free liquid in the stream.4. T he liquids collected in both compartments of the vessel will need to be drained. Check the liquid level regularly to verify operation of automatic drain or, if there is no automatic drain, open manual drain in liquid reservoir and drain liquid as required. Never let the liquid level get above the top of the sump section.5. A s the cartridge loads with solids, the differential pressure across the filter vessel is expected to increase. The cartridge should be replaced when the differential pressure reaches 12-14 psid (0.8-1.0 bar) at normal operating pressure or every year, whichever comes first.• D o not backflow the filter vessel. A high velocity flowinside the cartridges could cause damage or causethe cartridge seal to become disengaged.• I f the filter vessel has been operating at a flow ratefar below its design capacity for any period of time,it should be blown down and removed from servicefor inspection and clean-out, regardless of pressuredrop, before increasing to operating at a maximumcapacity flow.• D o not clean the filter vessel with steam injected intothe first stage compartment with the cartridges stillinstalled. Make sure cartridges are removed prior toany steaming performed.• I f the solids being removed from the gas aresusceptible to causing combustion with air (i.e.iron sulfides/black powder), the filter vessel maybe flooded with water and then drained before theclosure is opened and spent cartridges are removed.This will reduce the risk of cartridges combusting.D. OPERATING INSTRUCTIONSPGC CARTRIDGE OPERATION IN VESSEL31. R eview all operating company safety procedures prior to cartridge replacement operations.2. F ollow all operating company safety and lockout/tag-out procedures.3. E nsure that all liquids are drained off the vessel before proceeding with the cartridge replacements.4. O pen filter bypass valve (if available) and then isolate the filter vessel by closing the inlet and outlet connection valves.5. O pen the blow-down connection or closure vent valve to relieve any pressure on the vessel.Ensure that the filter vessel pressure is atatmospheric pressure prior to proceeding.6. O pen the closure (according to closure manufacturer’s procedures).7. P ull retainer clips on front support screen and remove front support screen. Then remove dirty (spent) cartridges.Dispose of spent cartridges in accordancewith plant procedures and applicable lawsand regulations for disposal in your area. 8. I nspect and clean the filter vessel as needed. Make sure all debris is cleaned from the cartridge sealing surfaces. Make sure no cartridge gasket seals have been left in vessel during cartridge removal. If any vessel damage is found notify Parker immediately. Do not operate vessel until damage is fixed.9. I nstall new cartridges and ensure proper sealing on the riser post and seat. This particular series uses PGC cartridges which provides for Tool-Less cartridge change-outs.Slide white bayonet end of the cartridge through the riser pipe into the second stage of the vessel. Push the cartridge until the center chevron seal is fully inserted into the riser and stops. Repeat until all cartridges are-installed. Once the cartridges are-installed re-install the front support screen. This screen should slide over all the cartridge handles on the front end to allow support of the cartridges. Re-install retainer clips.The use of original OEM cartridges ishighly recommended to ensure thebest overall performance of the filter.Replacement cartridges can be orderedthrough your local Parker distributor.The cartridge Item Number andSeries Description can be found in theManufacturer’s Data Book supplied withyour vessel.10. I nstall a new closure gasket. The use of originalclosure manufacturer’s gasket is highly recommended to ensure the best overall performance of the filter.Replacement gaskets can be ordered through yourlocal Parker distributor. The closure gasket ItemNumber and Series Description can be found in theManufacturer’s Data Book supplied with your vesseland also on the vessel nameplate.Installation of a new closure gasketduring each cartridge change is highlyrecommended.11. C lose the closure (according to closuremanufacturer’s procedures).12. M ake sure vent valve is open.13. M ake sure inlet and outlet valve are closed.14. S lowly and partially open the inlet connection valveand introduce the gas stream into the filter vessel.Allow gas to purge air from the filter vessel through the vent valve. Purging should only take a few seconds.15. Close vent valve.16. C heck for leaks. Should leak occur, close inlet valveimmediately and determine cause of leak.Make sure to fully depressurize the vesselprior to attempting to fix the leak.17. O nce no leaks are found, check to be sure that allauxiliary equipment is ready for operation.18. R epeat operating instructions in section B.E. M AINTENANCE INSTRUCTIONS – CHANGING SPENT CARTRIDGES4IOI-OG-GEM-200820® 2020 Parker Hannifin Corporation Parker Hannifin CorporationIndustrial Process Filtration DivisionPhone 940-325-2575 | Toll Free 1-800-877-7326*************************/ipfF. SUMMARY DATARecommended Cartridge Change-out Differential Pressure:12-14 psid (0.8-1.0 bar)Maximum Cartridge Differential Pressure at Collapse:25 psid (1.7 bar)Note: The following pressure information is provided as a minimum guideline. Due to the variety of cartridge models that can be used in vessel, it is strongly suggested to refer to the specific cartridge datasheet for further detailed pressure information. To prevent damage, never exceed the maximum allowable differential pressure of the cartridgesupport plate in the vessel.PEACH ® GeminiCartridge Series PGCAvailable in polyester or polypropylene media and micron ratings of 0.1 and 0.3.。
Festo Core Range一体化产品目录说明书
One-way flow control valves GRLA, GRLZe Festo Core RangeSolves the majority of your automation tasks With the Festo Core Range, we have selected the most important products and functions from our broad product catalogue, and added the quickest delivery.Worldwide: Simply good: Fast:Quickest delivery – wherever, wheneverExpected high Festo qualityEasy and fast to selectThe Core Range off ers you the best valuefor your automation tasks.Just lookfor thestar!One-way flow control valves Key featuresFunctionThe piston speed of both advancing and retracting pneumatic cylinders can be regulated using one-way flow con-trol valves. This is achieved by restricting the flowrate of compressed air in exhaust air orsupply air direction as required. Thenon-return function works in the oppo-site direction.The flow control function creates anadjustable annular gap inside thevalve. This gap can be increased or de-creased by turning the knurled screwor slotted head screw.The required restriction can be set withthe help of this adjustment element.General informationStandard nominal flow rate qnN Standard flow rate qn Symbols ConnectionsThe standard nominal flow rate qnN is the volumetric flow rate based on standard conditions at an operating pressure of p1 = 6 bar and an output pressure of p2 = 5 bar, measured at room temperature t = 20°C.The standard flow rate qn is measuredat an operating pressure of p1 = 6 barand an output pressure with respect toatmospheric pressure (p2 = 0 bar).Exhaust air one-way flow control func-tionSupply air one-way flow control func-tion21[1] Pneumatic connection 1 (com-pressed air connection)[2] Pneumatic connection 2 (workingport)2d I nternet: /catalogue/...Subject to change – 2023/05One-way flow control valves Key featuresApplication examplesMini slide SLT with one-way flow control valve, standard Flat cylinder DZF with one-way flow control valve, mini3 2023/05 – Subject to change d I nternet: /catalogue/...One-way flow control valvesProduct range overview – One-way flow control valves1)Standard nominal flow rate in flow control direction.2)Only suitable for push-in connector QS.4d I nternet: /catalogue/...Subject to change – 2023/05One-way flow control valves Product range overview – One-way flow control valves1)Standard nominal flow rate in flow control direction.5 2023/05 – Subject to change d I nternet: /catalogue/...One-way flow control valvesType codes6d I nternet: /catalogue/...Subject to change – 2023/0572023/05 – Subject to change d I nternet: /catalogue/...One-way flow control valves GRLA/GRLZ, standardDatasheet – Push-in connector QS, metalOne-way flow control function Can be rotated 360° around the screw-in axis after installation.-M- Flow rate100 ... 1580 l/min -Q- Temperature range –10 ... +60°C -L-Operating pressure0.2 ... 10 barGRLA/GRLZGRLA-...-RS1)More information: /catalogue/grla d Support/DownloadsStandard nominal flow rate qnN at 6 a 5 bar as a function of spindle rotations n Standard flow rate qn at 6 a 0 bar as a function of spindle rotations n GRLA/GRLZ-M5GRLA/GRLZ-M5Exhaust airSupply airOne-way flow control valves GRLA/GRLZ, standardDatasheet – Push-in connector QS, metal8d I nternet: /catalogue/...Subject to change – 2023/05One-way flow control valves GRLA/GRLZ, standard Datasheet – Push-in connector QS, metalMaterialsSectional view9 2023/05 – Subject to change d I nternet: /catalogue/...One-way flow control valves GRLA/GRLZ, standardDatasheet – Push-in connector QS, metalq Core Range10d I nternet: /catalogue/...Subject to change – 2023/05One-way flow control valves GRLA/GRLZ, standardDatasheet – Female thread/barbed connector, metalOne-way flow control function -M- Flow rate83 ... 4320 l/min -Q- Temperature range –10 ... +60°C -L-Operating pressure0.2 ... 10 barGRLA/GRLZGRLA/GRLZ-...-RSGRLA/GRLZ-...-PK1)-H-Note: This product conforms to ISO 1179-1 and ISO 228-1.1)-H-Note: This product conforms to ISO 1179-1 and ISO 228-1.1)More information: /catalogue/grla dSupport/DownloadsExhaust airSupply airOne-way flow control valves GRLA/GRLZ, standard Datasheet – Female thread/barbed connector, metalOne-way flow control valves GRLA/GRLZ, standardDatasheet – Female thread/barbed connector, metalMaterialsSectional viewOne-way flow control valves GRLA/GRLZ, standard Datasheet – Female thread/barbed connector, metal-H-Note: This product conforms to ISO 1179-1 and ISO 228-1.One-way flow control valves GRLA/GRLZ, standard Datasheet – Female thread/barbed connector, metal1)Via union nut2)Male thread3)Female thread4)For barbed connector internal diameter with union nut1)Via union nut2)Male thread3)Female thread4)For barbed connector internal diameter with union nutOne-way flow control valves GRLSA, standardDatasheet – Push-in connector QS, metalOne-way flow control function -M- Flow rate 0 ... 450 l/min -Q- Temperature range –10 ... +60°C -L-Operating pressure0.2 ... 10 barThis one-way flow control valve pro -vides the perfect conditions and a unique design for optimum and easy setting of the flow rate.There are two setting options:[1] Gradual for preselecting the flowrate range in 5 steps using a rota -ry switch:A, B, C, D, E[2] Infinitely variable for precision ad -justment with a hex key using ascale marked from 0 to 10Exhaust airOne-way flow control valves GRLSA, standardDatasheet – Push-in connector QS, metalnq n N [l /m i n ]1234567891050100150200250300350400450500n123456789100100200300400500600700800Stage: A Stage: B Stage: CStage: D Stage: EFlow rate value tolerance: ±20%Materials Sectional viewOne-way flow control valves GRLSA, standard Datasheet – Push-in connector QS, metalOne-way flow control valves GRLA/GRLZ, miniDatasheet – Push-in connector QS, metalOne-way flow control function Low flow: precise adjustment For low speed-M- Flow rate40 ... 48 l/min -Q- Temperature range –10 ... +60°C -L-Operating pressure0.2 ... 10 bar1)More information: /catalogue/grla dSupport/DownloadsExhaust airSupply airOne-way flow control valves GRLA/GRLZ, miniDatasheet – Push-in connector QS, metaln1234567891001020304050607080MaterialsSectional viewOne-way flow control valves GRLA/GRLZ, mini Datasheet – Push-in connector QS, metal21 2023/05 – Subject to change d I nternet: /catalogue/...22d I nternet: /catalogue/...Subject to change – 2023/05One-way flow control valves GRLA/GRLZ, miniDatasheet – Female thread, metalOne-way flow control function -M- Flow rate0 ... 18 l/min -Q- Temperature range –10 ... +60°C -L-Operating pressure0.2 ... 10 bar1)More information: /catalogue/grla d Support/DownloadsStandard nominal flow rate qnN at 6 a 5 bar as a function of spindle rotations nStandard flow rate qn at 6 a0 bar as a function of spindle rotations nn1234567891005101520253035404550Exhaust air Supply airOne-way flow control valves GRLA/GRLZ, mini Datasheet – Female thread, metalMaterialsSectional view23 2023/05 – Subject to change d I nternet: /catalogue/...24d I nternet: /catalogue/...Subject to change – 2023/05One-way flow control valves CRGRLA, corrosion-resistantDatasheet – Female thread, stainless steelOne-way flow control function -M- Flow rate95 ... 2100 l/min -Q- Temperature range –20 ... +80°C -L-Operating pressure0.3 ... 10 bar-H-Note: This product conforms to ISO 1179-1 and ISO 228-1.1)More information /x/topic/crc2)More information: /catalogue/crgrla dSupport/Downloads.Exhaust airOne-way flow control valves CRGRLA, corrosion-resistant Datasheet – Female thread, stainless steelStandard nominal flow rate qnN at 6 a 5 bar as a function of spindlerotations nStandard flow rate qn at 6 a 0 bar as a function of spindle rotations n CRGRLA-M5, CRGRLA-1/8CRGRLA-M5, CRGRLA-1/8Standard nominal flow rate qnN at 6 a 5 bar as a function of spindlerotations nStandard flow rate qn at 6 a 0 bar as a function of spindle rotations n CRGRLA-1/4, CRGRLA-3/8, CRGRLA-1/2CRGRLA-1/4, CRGRLA-3/8, CRGRLA-1/2MaterialsSectional view25 2023/05 – Subject to change d I nternet: /catalogue/...One-way flow control valves CRGRLA, corrosion-resistantDatasheet – Female thread, stainless steel-H-Note: This product conforms to ISO 1179-1 and ISO 228-1.26d I nternet: /catalogue/...Subject to change – 2023/05Festo - Your Partner in AutomationConnect with us/socialmedia 1Festo Inc.2Festo Pneumatic 3Festo Corporation 4Regional Service Center 5300 Explorer DriveMississauga, ON L4W 5G4CanadaAv. Ceylán 3,Col. Tequesquináhuac 54020 Tlalnepantla, Estado de México1377 Motor Parkway Suite 310Islandia, NY 117497777 Columbia Road Mason, OH 45040Festo Customer Interaction CenterTel:187****3786Fax:187****3786Email:*****************************Multinational Contact Center 01 800 337 8669***********************Festo Customer Interaction Center180****3786180****3786*****************************S u b j e c t t o c h a n g e。
Schurter PG05 1孔无线滤波器入口模块说明说明书
1IEC Appliance Inlet C14 with Fuseholder 1- or 2-pole, Line Switch 2-pole and Voltage SelectorOrder required accessories separatelySee below:Approvals and CompliancesC1470° CDescription- Panel mount :Screw-on version from front or rear side, snap-in version from front side- 4 Functions :Appliance Inlet Protection class I , Line Switch 2-pole , Fuseholder with interchangeable fuse drawer for Fuse-links 5x20 mm or 6.3x32 mm , with or without voltage selector (step) - V-Lock notch standard- Meets the requirements of IEC 60335-1 for appliances in unattended use. This includes the enhanced requirements of glow wire tests acc. to IEC 60695-2-12 and -13.- Quick connect terminals 4.8 x 0.8 mmCharacteristics- All single elements are already wired- The fuse drawer ?Fingergrip? can be removed by hand - Suitable for use in equipment according to IEC/UL 60950Other versions on request- Line switch, illuminated- Line switch with other rocker marking - Line switch 1-pole- For protection class II (without CCC approval)References Alternative: version with line filter CDWeblinkspdf datasheet , html-datasheet , General Product Information , Distributor-Stock-Check , Accessories , Detailed request for product , MicrositeT echnical DataRatings IEC10 A / 250 VAC; 50 Hz Ratings UL/CSA 10 A / 125 VAC; 60 Hz Dielectric Strength> 3 kVAC between L-N > 4 kVAC between L/N-PE (1 min/50 Hz)Allowable Operation Tempe-rature-25 °C to 70 °CIP-Protection from front side IP 40 acc. to IEC 60529Insulation cover Suitable for appliances with protection class I acc. to IEC 61140TerminalQuick connect terminals 4.8 x 0.8 mm , tin-platedPanel Thickness SScrew: max 8 mmMounting screw torque max 0.5 Nm Snap-in: 1.5/2/2.5 mmMaterial: HousingThermoplastic, black, UL 94V-0appliance inlet/-outletC14 acc. to IEC 60320-1,UL 498, CSA C22.2 no. 42 (for cold conditions) pin-temperature 70 °C, 10 A, Protection Class IFuseholder1 or2 pole, Shocksafe category PC2 acc. to IEC 60127-6,for fuse-links 5 x 20 or 6.3 x 32 mm Rated Power Acceptance @ Ta 23 °C5 x 20: 2.5 W (1 pole)/ 2 W (2-pole) per pole6.3 x 32: 3.15 W (1 pole)/ 2.5 W (2-pole) per polePower Acceptance @ Ta > 23°C Admissible power acceptance at higher ambient temperature see derating cur-vesLine SwitchRocker switch 2-pole, non-illuminated, acc. to IEC 61058-1 Technical DetailsVoltage Selectoroptional, step, 2-4 digitsApprovals and CompliancesDetailed information on product approvals, code requirements, usage instructions and detailed test conditions can be looked up in Details about ApprovalsApprovalsThe approval mark is used by the testing authorities to certify compliance with the safety requirements placed on electronic products. Approval Reference T ype: KDApproval Logo Certificates Certification Body DescriptionVDE Approvals VDE Certificate Number: 40029908UL Approvals UL UL File Number: E93617CSA Approvals CSACSA Certification Record: 38456CQC Approvals CQC CCC Certificate Number: 2010010204409773 Product standardsProduct standards that are referencedOrganization Design StandardDescriptionDesigned according to IEC 60320-1Appliance couplers for household and similar general purposesDesigned according to IEC 60127-6Miniature fuses. Part 6. Fuse-holders for miniature fuse-linksDesigned according to IEC 61058-1Switches for appliances. Part 1. General requirementsDesigned according to UL 498Standard for Attachment Plugs and ReceptaclesDesigned according to CSA C22.2 no. 42General Use Receptacles, Attachment Plugs, and Similar Wiring Devices Application standardsApplication standards where the product can be usedOrganization Design StandardDescriptionDesigned for applications acc.IEC/UL 60950IEC 60950-1 includes the basic requirements for the safety of informationtechnology equipment.Designed for applications acc.IEC 60601-1Medical electrical equipment - Part 1: General requirements for basicsafety and essential performanceDesigned for applications acc.IEC 60335-1Safety of electrical appliances for household and similar purposes. Meetsthe requirements for appliances in unattended use. This includes the en-hanced requirements of glow wire tests acc. to IEC 60695-2-12 and -13. CompliancesThe product complies with following Guide LinesIdentification Details Initiator DescriptionCE declaration of conformity SCHURTER AG The CE marking declares that the product complies with the applicablerequirements laid down in the harmonisation of Community legislation onits affixing in accordance with EU Regulation 765/2008.RoHS SCHURTER AG EU Directive RoHS 2011/65/EUChina RoHS SCHURTER AG The law SJ / T 11363-2006 (China RoHS) has been in force since 1 March2007. It is similar to the EU directive RoHS.REACH SCHURTER AG On 1 June 2007, Regulation (EC) No 1907/2006 on the Registration,Evaluation, Authorization and Restriction of Chemicals 1 (abbreviated as"REACH") entered into force.MicrositeV-Lock SCHURTER AG V-Lock system are based on a matching plug-dose combination. Theconnector is equipped with a notch intended for use with the latchingcordset. The cord latching system prevents against accidental removal ofthe cordset.White paperGlow wire test SCHURTER AG Meets the requirements of IEC 60335-1 for appliances in unattended use.This includes the enhanced requirements of glow wire tests acc. to IEC60695-2-12 and -13.Medical Equipment SCHURTER AG Suitable for use in medical equipment according to IEC/UL 60601-123Dimensions [mm]Screw-on mounting+0.2Snap-in mounting+0.2Diagramswithout voltage selector1-polewithout voltage selector2-polewith voltage selector1-polewith voltage selector2-pole4Derating Curves Fuses5 x 20 mm (1-pole)A d m i s s i b l e p o w e r a c c e p t a n c e i n W a t t1.51.00.50.02.52.0Ambient air temperature Ta °C Fuses5 x 20 mm (2-pole, per pole)A d m i s s i b l e p o w e r a c c e p t a n c e i n W a t t p e r p o le2.01.51.00.50.0Ambient air temperature Ta °CFuses6.3 x 32 mm (1-pole)A d m i s s i b l e p o w e r a c c e p t a n c e i n W a t t1.51.00.50.02.52.0Ambient air temperature Ta °C Fuses6.3 x 32 mm (2-pole, per pole)A d m i s s i b l e p o w e r a c c e p t a n c e i n W a t t p e r p o le1.51.00.50.02.52.0Ambient air temperature Ta °CAll VariantsPackaging unit 20 PcsRequired AccessoryDescriptionFusedrawer 3Fusedrawer for Fuse Links 5x20 mm resp. 6.3x32 mmFingergrip, 5 x 20, 2-pole, Voltage Selector4303.2014.00Fingergrip, 5 x 20, 2-pole, Voltage Selector, 100, 120, 220, 2404303.2014.01Fingergrip, 5 x 20, 2-pole, Voltage Selector, 110, 150, 2204303.2014.02Fingergrip, 5 x 20, 2-pole, Voltage Selector, 110, 2204303.2014.03...AccessoriesWire HarnessWire harness for SCHURTER productsAssorted CoversRear Cover0859.0074Cord retaining kitsCord retaining strain reliefFlat head, A4700.0001Mating Outlets/ConnectorsCategory / DescriptionAppliance Outlet Overview completeIEC Appliance Outlet F, Screw-on Mounting, Front Side, Solder Terminal4787IEC Appliance Outlet F, Snap-in Mounting, Front Side, Solder or Quick-connect Terminal4788IEC Appliance Outlet F or H, Screw-on Mounting, Front Side, Solder, PCB or Quick-connect Terminal5091Appliance Outlet further types to KDConnector Overview complete4782 Mounting: Power Cord, 3 x 1 mm² / 3 x 18 AWG, Cable, Connector: IEC C1347824785 Mounting: Power Cord, 3 x 1 mm² / 3 x 18 AWG, Cable, Connector: IEC C1347854300-06 Mounting: Power Cord, 3 x 1 mm² / 3 x 18 AWG, Cable, Connector: IEC C134300-06IEC Connector C15 for hot conditions 120°C, Rewireable, Straight4781IEC Connector C15 for hot conditions 120°C, Rewireable, Angled4784Connector further types to KD...56Mating Outlets/Connectors shutteredPower Cord Overview completeVAC13KS, Overview, diverse Connector IEC C13, cord end:VAC13KSPower Cord further types to KDThe specifications, descriptions and illustrations indicated in this document are based on currentinformation. All content is subject to modifications and amendments. Information furnished is believed 11.09.2018。
Touchpoint TM Plus 气体检测器控制系统说明书
Gas DetectionTouchpoint TMPlusTouchpoint Plus brings a whole new control experience to your small system of gas detectors. Touchpoint Plus is an easily configurable, wall-mounted control system that supports up to 16 gas detection channels. Its modular approach enables you to take control and configure what you need for a wide range of applications.The signature feature of the Touchpoint line is a user-friendly touchscreen interface, which the Touchpoint Plus takes to a new level. With this unique interface, it’s easier than ever to see the status of your system at a glance - maximizing the time you have to make the right decisions. The intuitive, multilingual interface simplifies operation and reduces training requirements. The full-color stoplight-style status indication provides clarity from a distance too.Touchpoint Plus features a comprehensive set of outputs as standard, including common alarms and dedicated drives for remote audiovisual indicators. Its modularity enables you to customize your system to meet your specific application requirements. Selecting the right detector for use with your controller can deliver significant savings in startup costs and ongoing operations. Our global partner network and dedicated application specialists are able to help you make the right choices for your industry.With everything at your fingertips, you can take ownership of your system and operate it with confidence, helping to ensure the safety of your people and the productivity of your site.Delivering Reliable Control • Honeywell reliability from the most trusted experts in gas detection• Built-in battery backup for constant uptime• Robust, shockproof housing for a wide range of industrial environments Flexible Capabilities• Compatible with the full range of Honeywell gas detectors • Powered audiovisual alarms simplify field installation • Configuration includes easy grouping and voting alarm logic without specialist knowledge • Next-generation compatibility • Optional Modbus output for integration with a higher level systemProviding Ease and Efficiency • Quick and easy installation, configuration, setup, and maintenance• Easy diagnostics, data, and reporting• Minimum training time• Large color touchscreen LCD • Multilingual functionality • Green-yellow-red status at a glanceWant toknow what’sgoing on?View real-time andhistorical data, analyzereadings, andmuch more System status at a glanceBuilt-in sounderIndividual channel status indicators (green, yellow, red)Mute/Resetdetection systems across a wide range of applications and industries. If you need to integrate your gas detection with a higher-level management system, the Modbus output option makes this straightforward.As the heart of your gas detection system, Touchpoint Plus is designed to work with Honeywell’s industry-leading gas detectors and drive actuators, and audible and visual alarms to provide a complete end-to-end solution that you can configure as your own.Relays, actuators, and XNX universal transmitterGasDetector Audible & Visual AlarmTYPICAL EXAMPLE OF A SMALL GAS DETECTION SYSTEM USING TOUCHPOINT PLUSDesigned for Speed and ReliabilityMade of high-impact polymer plastic, Touchpoint TM Plus is versatile and durable. It is dustproof and waterproof, and has been tested to withstand the toughest operating environments, both indoors and out. So you can count on the Touchpoint Plus to stand up to the challenges of industrial environments, from mechanical rooms to chemical plants.Touchpoint Plus is supplied with pre-drilled and sealed cable entries and a unique tiered internal arrangement providing ease of access to save installers time and money.1. Main module2. Input module3. Relay output module4. mA output module5. Power supply6. Display module7. Touchscreen8. Backup battery9. Modbus TCP/Web 10. Modbus RTU12345869107System Configuration Options2, 4, or 8 Inputs 2-Wire 4-20 mA 3-Wire 4-20 mA 3-Wire mV BridgeProvided As Standard• Dedicated powered audiovisual alarm drives• Common alarm outputs, one for fault and two configurable • Datalogging to SD card•Remote reset and inhibit inputsOptions• Choice of AC or DC supply voltage • Optional backup battery• Choice of inputs: 2, 4 , or 8 mA; 2, 4 , or 8 mV; 2 mA and 2 mV; 4 mA and 4 mV • Optional expansion unit for up to 16 inputs• Choice of 12 or 24 relay outputs • Choice of 4 or 8 mA outputs • Optional RS485 Modbus RTU • Optional TCP/IP Modbus/HTTPQuick and easy installation - designed to save you time and moneyTouchpoint TM Plus can be directly wall-mounted, or, for an easier 1-man installation, simply use the optional mounting plate. Open the hinged front cover to find plenty of space for wiring and a unique tiered terminal arrangement for easy access. Cable entries are pre-drilled and sealed ready to use reducing installation time and cost further.Direct Surface MountingOptional Mounting PlateTouchpoint Plus is supplied with 13 pre-drilled and sealed cable entries for PG16/M20 glands.Note: Other field devices available on request. Some devices are not available in all regions.InstallationB: Base Unit E: Expansion UnitPlease Note:While every effort has been made to ensure accuracy in this publication, no responsibility can be accepted for errors or omissions. Data may change, as well as legislation, and you are strongly advised to obtain copies of the most recently issued regulations, standards, and guidelines. This publication is not intended to form the basis of a contract.Touchpoint Plus Datasheet | Rev 4 | 02/19© 2019 Honeywell International Inc.For more information Europe, Middle East, AfricaLife Safety Distribution GmbHTel: 00800 333 222 44 (Freephone number)Tel: +41 44 943 4380 (Alternative number)Middle East Tel: +971 4 450 5800 (Fixed Gas Detection)Middle East Tel: +971 4 450 5852 (Portable Gas Detection)AmericasHoneywell Analytics Distribution Inc.Tel: +1 847 955 8200Toll free: +1 800 538 0363RAE Systems by Honeywell Phone: 408 952 8200Tollfree:188****4800Asia PacificHoneywell Industrial Safety Tel: +82 (0) 2 6909 0300India Tel: +91 124 4752700China Tel: +86 10 5885 8788 3000**************************Technical SupportEMEA:**********************US:***************************AP:***************************。
Heka EPC 10 USB 电子吸管电流仪家族用户指南说明书
Smart Ephys. The Smart Source for All Your Ephys Needs.Fully computer-controlled Patch Clamp AmplifiersIntroductionThere are many advantages to a fully digitally-controlled patch clamp amplifier. Three major advantages em-ployed in the design of the EPC 10 USB are:• First, since all of the functions of the amplifier are controlled by a data acquisition program all of the amplifiers hardware settings can be stored along with the data. Not only is this capability important when reviewing and ana-lyzing the data but also for complete and thorough experimental book-keeping.• S econd, computer control allows a number of operations to be fully automated. These can include automaticmode switching (e.g. switching between the settings for establishing a seal or those for single-channel recording), automatic capacitance neutralization of C-Fast and C-Slow, and series resistance compensation. In fact, digital control of every adjustable parameter in the amplifier circuitry is implemented including full functionality test and calibration. • Finally, the integration of the amplifier, data acquisition interface and software allows experiments to be easily repli-cated to exact details.1) Electronic Design of the Patch Clamp. F .J.Sigworth. Single-Channel Recording, Second Edition, edited by Bert Sackmann and Erwin Neher. Plenum Press, New York, (1995) 95-127.2) Design of the EPC-9, a computer–controlled patch-clamp amplifier. 1. Hardware, F .J.Sigworth, Journal of Neuroscience Methods 56 (1995) 195-202.3) Design of the EPC-9, a computer–controlled patch-clamp amplifier. 2. Hardware, F.J.Sigworth, H.Affolter, E.Neher, Journal of Neuroscience Methods 56 (1995) 203-215.HEKA is very proud to release the EPC 10 USB - the newest member of the EPC 10 family of fully com-puter-controlled patch clamp amplifiers. The EPC 10 USB continues the HEKA commitment to provide the most up-to-date and technologically advanced pro-ducts for scientific research. The EPC 10 USB is the successor to the revolutionary EPC 9 patch clamp amplifier, which was introduced in 19901)2)3), as well as the renowned EPC 10.The EPC 10 USB patch clamp amplifier is available with either one (EPC 10 USB), two (EPC 10 USB Double), three (EPC 10 USB Triple) or four (EPC 10 USB Quadro) integrated amplifier modules.The EPC 10 USB is fully integrated with HEKA´s new LIH 8+8 data acquisition interface. The LIH 8+8 is a high resolution, low noise scientific data acquisition in-terface that utilizes the latest Analog to Digital, Digital to Analog, USB 2.0 and high-speed processor techno-logies. This powerful hardware combination in con-junction with PATCHMASTER or PATCHMASTER NEXT software provides a highly-integrated system that will minimize total recording noise, eliminate compatibility problems, reduce additional equipment expense, and most importantly, set-up time.ApplicationsThe EPC 10 USB family of amplifiers can be used, for example, for any of the following applications:• Low noise single-channel recordings• Low noise whole-cell patch clamp recordings: voltage clamp and cur-rent clamp/Low Frequency Voltage Clamp (LFVC)• Measurements of fast action potentials (AP), fast switching between voltage and current clamp and vice versa.• Loose-patch recordings4).• Intracellular voltage recordings with high resistance electrodes.• Field potential recordings.• Recordings from artificial membranes (Bilayer Recordings) and nano-pores.• Study Synaptic Transmission by simultaneous stimulation/recording from multiple cells (e.g. pre- and post-synaptic cells).• Study of Long Term Potentiation (LTP) and Long Term Depression (LTD).• Study of Exocytosis/Endocytosis or Synaptic Transmission by -Measurement of whole-cell membrane capacitance-Measurement of on-cell membrane capacitance-Detection of released substances (amperometry with e.g. carbon fiber electrodes)-Detection of released substances under a patch (patch ampero-metry)-Combined membrane capacitance measurements with ampero-metry (using EPC 10 USB Double)-Combined patch amperometry and on-cell capacitance measure-ments (using EPC 10 USB Double)• All above mentioned methods can be combined with photometric de-termination of e.g. the internal calcium ion concentration. Models and FeaturesThe EPC 10 USB is a complete data acquisition system, which can be used with HEKA’s PATCHMASTER or PATCHMASTER NEXT software.A DLL (dynamic link library) is available for software developers who are interested in writing their own Windows data acquisition software.The EPC 10 USB patch clamp amplifier, combined with a computerand PATCHMASTER / PATCHMASTER NEXT software is equivalent to a fully-equipped recording setup, which includes a patch clamp amplifier, a digital storage oscilloscope, a variable analog filter, a sophisticated pulse generator, and a full featured data acquisition and analysis system.Revision “T” Improvements Extended Stimulus RangeFilter 2 Bypass4) Loose Patch Recording. W. Stühmer. Practical Electrophysiologica Methods, edited by H. Kettenmann and R. Grantyn. Wiley-Liss, New York, (1992) 271-273.EPC 10 USB Patch Clamp Amplifier family Common Features• F ully computerized patch clamp amplifier that has a built-in data acquisition interface.• T he integration of the built-in low noise LIH 8+8data acquisition interface and the amplifier provides optimal grounding, removes external connections and only requires a single USB 2.0 (Hi-speed) port connection.• Compatible with either Windows or Mac OS systems, fully controlled via the PATCHMASTER / PATCHMASTER NEXT software• Software testing and calibration routines allows the user to verify the working condition of the instrument within minutes. Calibration, which typically required that the amplifier be taken out of service can be performed in-house, within a few minutes, withno additional expense, and more importantly no downtime to the recording setup. In addition, if needed, the headstage can be easily replaced and calibrated by the user.• The EPC 10 USB features C-Slow compensation in the high gain range (50 GΩ feedback resistor) for low noise whole-cell measurements.• U ltra slim low noise headstage design is optimized for single-channel, whole-cell and loose-patch current recordings • Resistor switching headstage with three gain ranges can be switched during an experiment• True Current Clamp capabilities• A “Low Frequency Voltage Clamp”(LFVC) modeis provided to automatically inject an appropriate amount of current to preserve the membrane potential, at a desired level during current clamp measurements.• Gentle Switch option from voltage clamp to current clamp (injection current is equal to the current monitor in voltage clamp mode)• Automatic or manual C-Fast and C-Slow capacitance neutralization• Capacitance tracking• Hardware leak compensation for non-voltage gated channels• T rue noise measurements from 100 Hz to 15 kHz• B uilt-in tone generator fully controlled by software • 16 Digital-In and 16 Digital-Out connections at the rear panel. Three of the Digital-Out connectors are also provided via BNC on the front panel.• All amplifier settings and parameters are stored with the data.• EPC DLL (dynamic link library) for controlling the EPC 10 USB is available for writing custom Windows applicationsFurther configurations are available. For more information see our product overview.Smart Ephys. The Smart Source for All Your Ephys Needs.EPC 10 USB AmplifiersThe number of recording channels and the number of amplifiers can be increased by con-necting two EPC 10 USB amplifiers. On the rear panel of the EPC 10 USB there are “SlaveSync” and “Master Sync” CAT5 connectors. EPC 10 USB amplifiers can be connected inFor example, an 8-channel parallel patch clamp amplifier can be configured by connecting two EPC 10 USB Quadro. These 8 in-dependent patch clamp amplifiers can be controlled by one copy of PATCHMASTER. Expandability to a 16-channel parallel patch clamp amplifier can be done by connecting four EPC 10 USB Quadro. In this case the amplifiers are controlled by two copies of PATCHMASTER that are synchronized and data can be automatically transferred to a single data file.2 x EPC 10 USB Quadro Amplifier8 ProbesSmart Ephys. The Smart Source for All Your Ephys Needs.Software Control OptionsPATCHMASTER NEXTThe EPC 10 USB family of amplifiers can be controlled with PATCHMASTER NEXT software on either Windows (10 (64-bit)) or Mac (OS X 10.6+) platform. PATCHMASTER NEXT is a multi-channel stimulation/acquisition and control software. For more details please refer to the PATCHMASTER NEXT brochure or contact us.CDEFGBAAmplifier WindowEach amplifier control can be accessed through the software and all hardware parameters can be accessed. This window is customizable in respect to displayed and required hard-ware parameters.Oscilloscope WindowAll acquired and replayed data will be displayed in this window.Control WindowThe control center of the PATCHMASTER NEXT soft-ware. Here, you start, break and or pause your experiments. Further, you have access to all main windows and the configu-ration of PATCHMASTER NEXT.Test Pulse WindowThis window is essential for the patch process itself. A run-ning test pulse is necessary to estimate important cell param-eters like membrane resistance or offset currents. Further, one can easily detect changes in patch clamp conditions during an ongoing experiment. Each amplifier board has its own test pulse view pane.Data TreeShows all the acquired data of the currentlyloaded data file. The tree-like organization of the data enables fast and easy data screening.Notebook WindowAll relevant software information is plotted into the Notebook which can be stored along with the data itself. Further, the Notebook Window is an important place to write on- and offline analysis results.Graph LayoutAnalysis results can be plotted on- or offline in analysis graphs which are displayed in the Graph Layout window.In this editor you define the pattern of the stimulation sequence. You have access to all output and input channels of the EPC 10 USB amplifier. Numer-ous different segment classes, an Increment Editor and a File Template Edi-tor allows you to create almost every possible stimulation sequence.The Protocol Editor allows to create experimental protocols via an event list which is processed in the given order. In addition to data acquisition one can now control or interact with external devices, react to analysis results or create conditional loops including break conditions or assigned keys. The predefined protocol lines allow a highly standardized and automated experi-mental procedure.Protocol EditorSmart Ephys. The Smart Source for All Your Ephys Needs.HeadstagesS-Probe HeadstageThe unique feature of the S-Probe is the significantly reduced size and weight compared to our standard headstages. This allows for compatibility with a wider range of applicati-ons, especially when experimental space is limited or where the weight of the headstageitself matters. The electrical specifications of the S-Probe are identical to our standard Red Star Headstage, with the added feature of an optional bath sense connection ena-bling operation in 3-Electrode mode (with EPC 10 USB only). It is compatible with a new EPC 10 USB or EPC 800 USB amplifier and is also available as an upgrade. Check withour support team to find out if this headstage is supported by your HEKA patch clamp amplifier. The amplifier (EPC 10 USB) and the headstage need to be calibrated using PATCHMASTER NEXT or EPCMaster software.Red Star HeadstageThe Red Star Headstage is used with the EPC 10, EPC 10 USB or the EPC 800 USBPatch Clamp Amplifiers. It offers excellent noise levels in the most important 1 - 10 kHzbandwidth. Further, it has three feedback resistors (50 GΩ, 500 MΩ, 5 MΩ) for three gain ranges which are switchable during the measurement. The Red Star Headstage is also noise-optimized for demanding single-channel recordings. The amplifier (EPC 10 USB) and the headstage need to be calibrated using PATCHMASTER NEXT or EPCMaster software.Model CircuitsModel Cells for Patch Clamp AmplifiersS-Probe Headstage with 248 cm flexible ribbon cable and a BNC to SMA connectorGeneralNumber of Amplifiers/HeadstagesEPC 10 USB Single: 1EPC 10 USB Double: 2EPC 10 USB Triple: 3EPC 10 USB Quadro: 4Amplifier ControlFully software controlled patch clamp amplifier featuring e.g. direct access to all amplifier settings, automatic calibration and self testing/diagnosis procedures.Host Interface USB 2.0 Dimensions Main UnitWeight Main UnitDimensions HeadstageD x W x H: 90 x 17 x 14.5 mmPower SupplyPower requirements are 100 Watt. The logic controlled power supply automatically switches the voltage range. It operatesin the range 85 V to 250 V at line frequencies of 50 or 60 Hz. A shielded transformer minimizes noise pickup from power line frequencies.Ground LinesA Signal ground is accessible via a Banana plug on the front panel of the main unit and via a connector pin on the heads-tage. In case of EPC 10 USB Double, Triple and Quadro, all amplifiers share the same ground.A Chassis ground is accessible via a Banana plug on the front panel of the main unit. Chassis and Signal ground are connec-ted via a 10 MΩ resistor.Voltage Clamp ModeCurrent Measuring ResistorsThe headstage provides three feedback resistors.The gain ranges can be switched during the experiment.Low gain range (5 MΩ): ± 2 µA current range Medium gain range (500 MΩ): ± 20 nA current range High gain range (50 GΩ): ± 200 pA current range Current Gain SettingsLow gain range: 0.005, 0.01, 0.02, 0.05, 0.1, 0.2 mV/pA Medium gain range: 0.5, 1, 2, 5, 10, 20 mV/pAHigh gain range: 50, 100, 200, 500, 1000, 2000 mV/pAInput Capacitance < 1 pFNoise PerformanceMeasured with open input via external 8-pole Bessel filter. Medium gain range:up to 1 kHz: ~ 180 fA rms (theoretical limit)up to 3 kHz: ~ 320 fA rms (theoretical limit)up to 10 kHz: ~ 580 fA rmsHigh gain range:up to 1 kHz: ~ 31 fA rmsup to 3 kHz: ~ 72 fA rmsup to 10 kHz: ~ 350 fA rmsBandwidth100 kHz (low and medium gain range), > 60 kHz (high gain range)Current FilterFilter 1 is a 6-pole Bessel pre-filter with 10 kHz, 30 kHz, 100 kHz, and HQ 30 kHz. The EPC 10 USB Single, Double, and T riple allow to directly sample the current signal of Filter 1.Filter 2 is a 4-pole filter with 100 Hz to 15 kHz bandwidth with selectable Bessel or Butterworth characteristics. Filter 2 is usable in series with Filter 1 or as separate filter for external signals. Holding PotentialSoftware controlled holding within a ± 2000 mV range.External Stimulus Input (VC)Via a BNC connector at the front panel an external stimulus input can be added to the internal set holding potential. An external stim scaling circuit allows scaling of the external stimulus with a factor in the range of – 1.0 to + 1.0.Single Double Triple QuadroDepth x Width31.1 x 48.3 cmHeight14.5 cm18.0 cm26.9 cmmounts in a 19“ rackSingle Double Triple Quadro11.4 kg12.2 kg15.3 kg16.5 kgCompensations in Voltage Clamp Mode Pipette Offset Potential Compensation Automatic or manual adjustment of the offset potential in the range ± 200 mV.Injection CapacitorsThe C-Fast compensation signal is injected via a 1 pF capaci-tor. The C-Slow compensation signals are injected via a 10 pF capacitor in medium and low gain and via a 1 pF capacitor in high gain range.C-Fast CompensationAutomatic or manual compensation in all gain ranges:0 to 15 pF, 0 to 8 µs tau (calibrated)0 to ~ 80 pF (Extended C-Fast)C-Slow CompensationAutomatic or manual compensation in all gain ranges:0.2 to 1000 pF (low and medium range), 0.2 to 100 pF (high range).Rs range 1 MΩ to 1 GΩ.Synchronous C-Slow CompensationThe EPC 10 USB Double, Triple and Quadro provide the option for synchronous C-Slow compensation pulses on multiple cells. This is essential for using the C-Slow compensation when mea-suring on multiple electrically connected cells.Series Resistance CompensationMaximal compensation is 95% with the optimal settingbeing dependent on the cell capacitance.Equivalent time constants: 2 µs, 5 µs, 10 µs, 100 µsHardware Leak SubtractionAutomatic or manual linear leak subtraction in all gain ranges:0 to 2 nS (high range), 0 to 200 nS (medium range), 0 to 20 μS (low range).Injection time constant: 100 µsSoftware Leak SubtractionA versatile p/n leak subtraction is provided in combination with the PATCHMASTER / PATCHMASTER NEXT software.Other VC FeaturesZap PulseProvided by the PA TCHMASTER / PA TCHMASTER NEXT software. The amplitude (up to ± 1 V) and duration is programmable. Audio Resistance MonitorA 3.5 mm jack is provided at the rear panel for connecting phones or speakers. Volume and Resistance/Frequency ratio can be adjusted by the PATCHMASTER / PATCHMASTER NEXT software. Frequency range: 1 Hz to 10 kHz.Current Clamp ModeCurrent InjectionFour current injection gains are selectable:0,1 pA/mV range: ± 1 nA1 pA/mV range: ± 10 nA10 pA/mV range: ± 100 nA100 pA/mV range: ± 1 µAIn the “Extended Stimulus Range” the current injection capability in current clamp mode is increased by factor of “5”.Voltage GainTwo gains are selectable: Bit resolution:V-mon x 10: ± 1000 mV 30 µVV-mon x 100: ± 100 mV 3 µVVoltage FilterFilter 2 setting do also allow the filtering of the voltage signal in a current clamp measurement.Voltage Measuring RangeThe voltage measuring range is ± 1 V (± 5 V when usingthe “Extended Stimulus Range”) in current clamp mode.External Stim Input (CC)Via a BNC connector at the front panel an external stimulus input can be added to the internally set holding current. The scaling factor is determined by the selected current injection gain.C-Fast in CC ModeC-Fast is active in current clamp mode to allow voltage recor-dings at high bandwidth.Bridge ModeThe voltage drop across the pipette resistance can be compen-sated.Low Frequency Voltage Clamp (LFVC) Automatic current tracking readjusts the holding current to fix any slow voltage drift while in current clamp mode.Gentle SwitchWhen switching from voltage to current clamp, the holding cur-rent is automatically set to the “I-mon” in voltage clamp mode. Fast Mode SwitchingThe PATCHMASTER / PATCHMASTER NEXT software allows to rapidly switch between current and voltage clamp mode and vice versa during data acquisition.DA/AD ConverterStimulationNumber of DA-converters: 4Settling Time: 1 µsDA output voltage range: ± 10 VNumber of AD-converters: 2DA/AD resolution: 16 bitFastestSamplingRate:2channels 200kHz8 channels 50 kHzFree DA channelsEPC 10 USB Single: 3EPC 10 USB Double: 2EPC 10 USB Triple: 1EPC 10 USB Quadro: 0Free AD channelsEPC 10 USB Single: 5EPC 10 USB Double: 3EPC 10 USB Triple: 1EPC 10 USB Quadro: 0Digital Input/OutputDigital I/O: 16 digital in and 16 digital out channels are provided on a 40 pin male connector on the rear panel. Digital In: 16 channels provided at the Digital In connector on the rear panel.Digital Out: 16 channels provided at the Digital Out connector on the rear panel, three of them are also provided via BNCon the front panel.Trigger In: Via 1 BNC connector on the front panel data acquisition can be triggered externally.Master/Slave Sync2 CAT5 connectors for synchronization of a second amplifier/ interface system are provided at the rear panel.The Smart Source for All Your Ephys NeedsAmericas************************ (+1) 833 668 8632Europe, Middle East, Africa*********************(+49) 7121 909 2526Asia Pacific**************************(+86) 21 6226 0239©January22|HEKAElektronikGmbHProductnamesusedhereinareforidentificationpurposesonlyandmaybetrademarksoftheirrespectiveowners.HEKAdisclaimsanyandallrightsinthosemarks.Wereservetherighttoeffecttechnicalchangesasdevelopmentprogresses.Specialversionsareavailableonrequest.Furthertechnicaldataareprovidedbyadetaileddescription,whichisavailableonrequest.Awarrantyoftwoyearsappliestoallinstruments.。
leap AIGO操作手册范本
CNLC阵列感应仪器AFIT 操作手册（草稿）版本： 1.0日期： 2011-04-01目录第一章概论 (1)1.1 导言 (1)1.2 阵列感应(AFIT)仪器技术性能指标 (2)1.3 配套使用的附件 (3)1.4 AFIT输出曲线 (3)1.5 健康，安全，环保事项 (6)1.5.1 人身安全 (7)1.5.2 设备安全 (8)第二章测井基本理论及仪器工作原理 (9)2.1 仪器功能、特点概述 (9)2.2 测量工作原理 (10)2.2.1基本物理测量 (10)2.2.2测量工作原理 (11)2.2.3应用的基本理论 (13)2.2.4测量电路框图 (14)2.2.5功能单元电路描述 (16)第三章仪器操作 (18)3.1 工作前地面软硬件准备 (18)3.2 仪器供电 (18)3.3 仪器刻度及EEPROM数据加载 (20)3.4 现场测井步骤 (21)3.4.1 测井作业准备 (21)3.4.2 测井步骤 (21)3.4.3 注意事项 (22)3.4.4 输入输出参数 (22)3.4.5 仪器设置 (31)3.4.6 AFIT仪器监控量 (32)3.4.7 AFIT仪器命令 (32)3.5 仪器刻度. (33)3.5.1刻度原理 (33)3.5.2 刻度前准备及安全事项 (35)3.5.3车间刻度 (40)3.5.4 刻度报告 (47)3.6 维护与检测 (53)3.6.1 工具 (53)3.6.2 日常维护 (53)3.6.3 二级保养 (53)3.6.4 循环油设备操作规 (53)3.7 测井质量控制 (55)3.7.1 测速 (55)3.7.2 环境 (55)3.7.3 测量误差控制 (57)3.7.4 主要输出曲线质量要求 (60)3.7.5 主要输出曲线默认设置 (61)3.8 仪器故障 (65)3.8.1 仪器监控量以及仪器曲线 (65)3.8.2 常见问题及解决方案 (65)第一章概论1.1 导言LEAP800-A阵列感应测井仪（AFIT-Array Focusing Induction Tool,以下简称AFIT）是一种多频、多阵列、全数字化的阵列感应仪器。
ICP DAS PM-3112-240-MTCP 双循环单相智能电能表快速启动指南说明书
PM-3112-240-MTCP2 Loops single-phase Smart Power MeterQuick Start GuideProduct Website:https:///pm_3112_240_mtcp1. IntroductionICP DAS brings the most powerful, cost-effective, advanced Smart Power Meters PM-3000 series that gives you access to real-time electric usage for single-phase power measurement. With its high accuracy (<0.5% , PF=1 ), the PM-3000 series can be applied to both low voltage primary side and/or medium/high voltage secondary side and enables the users to obtain reliable and accurate energy consumption readings from the monitored equipment in real time under operation. These compact size and cost-effective power meters are equipped with revolutionary wired clip-on CT (various types, support input current up to 200 A). It operates over a wide input voltages range 10 ~ 300 VAC which allow s worldwide compatibility. And with 2 channels relay output, it can be linked with sirens or lightings for alarm messages. It also supports Modbus R TU, Modbus TCP or CAN bus protocols for easy integration.2.1. Caution & WarningThe meter contains hazardous voltages, and should never be disassembled. Failing to follow this practice will result in serious injury or death. Any work on or near energized meters, meter sockets, or other metering equipment could induce a danger of electrical shock. It is strongly recommended that all work should be performed only by qualified industrial electricians and metering specialist. ICP DAS assumes no responsibility if your electrical installer does not follow the appropriate national and local electrical codes.ICP DAS assumes no liability for any damage resulting from the use of this product. ICP DAS reserves the right to change this manual at any time without notice. The information furnished by ICP DAS is believed to be accurate and reliable. However, no responsibility is assumed by ICP DAS for its use, not for any infringements of patents or other rights of third parties resulting from its use.2.2. Product Warranty & Customer SupportICP DAS warrants all products free from defects in material and workmanship for a period of one year from the date of shipping. During the warranty period, we will, at our position, either repair or replace any product that proves to be defective.To report any defect, please contact ：+310-517-9888 or *******************2.3. Limitation of WarrantyThis warranty does not apply to defects resulting from unauthorized modification, misuse, or use for reason other than electrical power monitoring. The supplied meter is not a user-serviceable product.3. InstallationPlease use the soft dry clothes to clean the instrument.Please do not use any chemical or detergent or volatile solvents to clean the instrument, in order to avoid any possibility of the cover damage.3.1.•Dimension: 127mm（length）× 33mm（wide）× 105mm（high）•Products come with external split type clip-on CT’s. Disconnect the CT’s or use other CT’s is highly prohibited.•Please read this operation manual carefully before using.•Please re-confirm the measure position.•Reconfirm the RST (ABC) phase sequence of the power system.•PM-3133 series can be installed as rail mounting mode or embedded, no need to drill a hole or screw to fix it (rail mounting width can up to the length of 35 mm).•Meter auxiliary power for PM-311x series is DC +12V ~+48V or DC +10V ~ +30V (For PM- 311x-xxxC).3.2. Voltage Input1.PM-311x series: Input Voltage up to 300V. For any higher Input Voltage large than 300V, pleaseadd the PT (power transformer), and Change PT RATIO setup.Notice: Please check the L-N connection of PM-311x-xxxC series or it will cause the damage. Please refer the following diagram.3.3. Current Input1. The external CT’s are fragile, please handle with care.2. The current input of PM-311x series is in mA range. Only the ex-factory attached CT’s can be used. The other CT’s, for example, from panel will damage the instrument due to its large current (around 5A)3. When more than one smart meters (PM-311x series) are installed, please do not disconnect the CT with its original meter and mix use with each other. Since each set of smart meter (PM- 311x series) and its attached split type clip -on CT are calibrated set by set. The mix use may cause wrong measurements.4. To install CT’s correctly, please ensure the CT lines sequences is right before clip the CT’s onto the power cable of the monitoring equipment. (Detail will be found in next section)5. When measuring the current, the secondary circuit of a CT should never be opened when a load is passing through its primary. Make sure you always open the CT clip to detach the CT before removing the terminal lines. Otherwise, it will cause severe injury.6. Please handle with extra care, especially when the operation space of CT’s is limited.7. The current direction must follow K-L marked on CT’s.8. Please select the right size CT’s for different size of monitoring equipment cables:Power cable diameter ＜Φ10 use 60 A CT，Φ10～Φ16 use 100A CT，Φ16～Φ24 use 200A CT9. The maximum current value cannot exceed the CT rating.3.4. Connection3.5. CT’s installation steps 3.6. Wiring4. Relay Output & LED Indicator●Relay Output●LED IndicatorThe PM-311x as 4 LED to indicate the unit power status, communication, andpower data calculation.⏹RUN: Green, light up after communication ready. LED will flashwhen the unit is processing communication.⏹PWR: Red, Power on LED always on.⏹DO0: Green. LED DO0 will light up, when DO0 is “ON”.⏹DO1: Green. LED DO1 will light up, when DO1 is “ON”.5. Communication。
ON ICON ELECTRA-flo 5 系列热流测量系统说明书
ELECTRA-flo 5 SeriesPrecision Airflow MeasurementAn ON I CON BrandTHERMAL AIRFLOW MEASUREMENTSYSTEMThe ELECTRA-flo 5 Series represents the state-of-the-art in electronic airflow measurement and has the features and performance required by the challengingapplications found in todays complexHVAC systems.Precision Airflow MeasurementAn ON I CON BrandELECTRA-flo 5 SeriesTHERMAL AIRFLOW MEASUREMENT SYSTEMAPPLICATIONSBuilding Airflow Distribution Systems - Including supply, return, exhaust, relief and dedicated outdoor air systems (DOAS).Fan Inlet Airflow Measurement - Single inlet, dual inlet or fan wall installations.CALIBRATIONIndividual sensors receive a multi-point, NIST* traceable calibration of air velocity and temperature across the entire operating range.FEATURESAccommodates (32) Thermal Sensing Points per ArrayMore sensing points means more accurate measurements in challenging real world duct configurations.Serial Communication Bus Between Individual Sensors and TransmitterAllows for individual probes to be daisy chained together in the field and have a single straight run to the transmitter - saving time & money by simplifying the installation!Ruggedized, Hermetically Sealed Sensors -Precision Thermistors and Heating Circuit are Fully EncapsulatedProvides a high degree of protection from theenvironment and allows the sensor assembly to be cleaned without damage.Dedicated ELECTRA-flo G5 Transmitter with Display Each airflow measurement system comes complete with a transmitter that is factory matched andconfigured, guaranteeing system performance. The transmitter outputs airflow, velocity, and temperature over BACnet, MODBUS, and analog signal.True Dual Channel Version AvailableThe ELECTRA-flo G5 Dual Transmitter provides two separate airflow measurements in one transmitter. Duct size and sensor allocation is set independently for each channel.*National Institute of Standards and Technology The aperture’s injection molded shape has been engineered to providerobust sensor protection and minimize the angular flow effects naturally present in any duct. The flared aperture captures a representative sample of the ducted airflow, while the contoured leading edges prevent the creation of vortices. The center cross section of the aperturefunctions in the same manner as a venturi. It stabilizes and flattens the velocity profile at the point of measurement ensuring the airflow maintains full contact with the sensing thermistors. The flow conditioning characteristic of the aperture compensates for turbulent airflow with pitch and/or yaw angles up to ±30 degrees and produces an accuracy of ±2% of reading for each ELECTRA-flo sensor.Permanently installed airflow measurement systems provide the real time, actionable information required for the safe, code compliant and efficient operation of today’s high performance buildings.Air Monitor’s ELECTRA-flo 5 Series thermal dispersion airflow measurement instruments accurately measure airflow in a wide variety of commercial HVAC installations.At the heart of each ELECTRA-flo/S5 thermal probe array are pairs of precision matched thermistors installed in aerodynamic apertures. These sensor aperture assemblies are specifically designed to reduce the effects of angular flow distortions found within ducted air distribution systems. The design, construction, and calibration of each thermistor sensor pair ensures the accuracy and long term reliability of the measurement system.The stations feature S5 probes externally mounted and pre-wired,simplifying the installation process. The G5 transmitter can be mounted directly on the station or located remotely.ELECTRA-flo/CM Thermal AirflowMeasurement Station0-4000 FPMELECTRA-flo/MM Thermal AirflowMeasurement Station0-5000 FPMThe ELECTRA-flo/CM consists of S5 Series probe arrays mounted in a prefabricated station with air straightening cell.The aluminum cell features honeycomb construction, providing a robust, corrosion resistant air flow straightening system, allowing unsurpassed performance in difficult installation configurations.The cell design also provides extremely low airflow resistance while maximizing its' flow conditioning ability.The G5 transmitter can be mounted directly on the station or located remotely.ELECTRA-flo/CM Thermal Airflow Measurement Station0.000.020.040.060.080.100.120.140.160.180.200.220.240.260.280.300.320.340.36R e s i s t a n c e t o A i r f l o w , i n c h e s w .c .Airflow Velocity, FPMELECTRA-flo/CM Station Airflow Resistance125017502250275032503750ELECTRA-flo/FI Probe Array for Fan Inlet Installations The ELECTRA-flo/FI is a system of thermal probes and the associated hardware specifically designed for use in both single and dual inlet fan applications. The adjustable mounting brackets allow for easy installation of the sensors, and the transmitter interface provides a simple fieldcharacterization routine, allowing quick system set up in the field.The ELECTRA-flo/CD utilizes thermal dispersion sensing technology with an integrated damper to continuously measure and control ducted airflow. The ELECTRA-flo/CD features aluminum dampers with blade seals certified to Class 1A leakage rates as defined by AMCA. The ELECTRA-flo/CD is well suited for many VAV applications.ELECTRA-flo/CDELECTRA-flo/CD ThermalMeasurement and Control StationELECTRA-flo 5 Series Thermal Airflow Measuring Stations (Continued)Additional Products in the ELECTRA-flo FamilyThe ELECTRA-flo/SD provides thermal dispersion airflow measurement for small duct applications from 4" to 16". It is ideal for direct VAV control in critical space applications.ELECTRA-flo/SD Thermal Airflow Probeand Transmitter ELECTRA-flo/FI Fan Wall(Array) for Multiple Fan Inlet InstallationsThe ELECTRA-flo/FI is designed to be installed in the environment found within the AHU itself, allowing for an easy and clean installation in fan wall (array) applications. Due to the ELECTRA-flo/FI’s sensor architecture, up to 32 individual fans can be measured by simply daisy chaining all of the fan inlet sensors back to a single transmitter. Utilizing the native BACnet serial communication capability found in the ELECTRA-flo G5 Transmitter, individual fan performance information can be brought back to the BMS.SPECIFICATIONS*ELECTRA-flo G5 Transmitter PERFORMANCESYSTEMCONFIGURATIONSingle or dual channel operationSupports up to 32 individual thermal dispersion airflow sensors Provides airflow velocity, flow and temperatureSupports multiple airflow measurement system types Provides three (3) field characterization methods OPERATING CONDITIONS AMBIENTTEMPERATURE -20°F to 180°F (Storage), -20°F to 140°F (Operating)HUMIDITY 0 to 99% RH, non-condensingINPUT POWER 24 VAC 20 - 28 VAC, 16 - 90 VA, Total VA = 15 VA + (# of sensors x 1.1 VA)24 VDC20 - 28 VDC, 16 - 50 W, varies based on # of sensors I/O SIGNALSTwo (2) analog outputs, selectable based on configuration ELECTRONICS ENCLOSUREAVAILABLE OPTIONS• Aluminum, NEMA 1• Stainless steel, NEMA 4X without viewing window • Aluminum , NEMA 1 with conduit connection box •Fiberglass, NEMA 4X with viewing windowDISPLAY2.75" x 2" TFT color LCDPROGRAMMING Menu driven user interface via four (4) push buttons ELECTRICAL CONNECTIONS POWER Removable terminal block for use with 14 to 18 AWG wire COMMUNICATIONS Removable terminal block for use with 14 to 22 AWG wire I/ORemovable terminal block for use with 14 to 22 AWG wirePROCESSCONNECTIONS AVAILABLE OPTIONS• NEMA 1 enclosure, two (2) mini-DIN connectors XMTR to probes and two (2) ½" conduit openings• NEMA 4X enclosure, two (2) liquid tight cord grips and two (2) ½" conduit openingsNETWORK CONNECTIONS RS485, BACnet MS/TP or MODBUS RTU APPROVALSUL 60730BTL Certified to BACnet standard ISO 16484-5 rev. 1.12FCCMeets part 15 Subpart B, Class A device requirementsELECTRA-flo/S5 Thermal Dispersion Probe Array PERFORMANCESENSOR ACCURACY Individual sensor accuracy: ±2% of reading from 0-5000 FPMSYSTEM ACCURACY Complete system accuracy: ±3% of reading over published velocity rangeVELOCITY RANGEDucted mounted installations: 0-5000 FPMStation mounted probe arrays: 0-5000 FPM (0-4000 FPM with straightening cell)Fan inlet installations: 0-10,000 FPMSENSOR DESIGNPrecision matched, hermetically sealed thermistors with laser trimmed resistive heating element Dedicated 16 bit A/D processing of each sensor signalSensor node consists of two (2) thermistors mounted in a dedicated flow conditioning aperture TEMPERATURE ACCURACY ±0.1°F over operating range of -20°F to 140°FSENSOR CAPACITY TRANSMITTER Maximum of 32 sensors per transmitter, shared between both channels PROBEMaximum of 8 sensors per probe* SPECIFICATIONS subject to change without notice.SPECIFICATIONS CONTINUED** SPECIFICATIONS subject to change without notice.Note¹ Field characterization required to achieve ±3% system accuracyELECTRA-flo/S5 Thermal Dispersion Probe Array (Continued)SENSOR DENSITYDUCT & STATION MOUNTED Three (3) sensor density levels specifiable based on configuration FAN INLETSingle or dual sensor configuration per inlet availablePROBEMATERIALS OF CONSTRUCTION AVAILABLE OPTIONS• 6063 anodized aluminum, 1⅛" diameter with NEMA 1 enclosure• 6063 anodized aluminum, 1⅛" diameter with NEMA 4 enclosure and IP68 liquid tight cord grips• 6063 anodized aluminum, 1⅛" diameter with NEMA 4 enclosure and ½" conduit connections OPERATING CONDITIONS FLUID TEMPERATURE -20°F to 140°FHUMIDITY0 to 99% RH, non-condensingWIRINGCONNECTIONS AVAILABLE OPTIONS• Mini-DIN, NEMA 1 only• Conduit opening with terminal blocks • IP68 liquid tight cord gripDUCT MOUNTED PROBE ARRAYS MOUNTING OPTIONS • Rectangular duct, external or internally mounted• Rectangular duct, standoff mount• Circular duct, external or internally mounted STATIONMOUNTED PROBE ARRAYSCONSTRUCTION OPTIONS• 14 ga. galvanized steel with 11/2" flange • 18 ga. stainless steel with 11/2" flange• Aluminum honeycomb airflow straightening cellELECTRA-flo/FI Thermal Dispersion Fan Inlet Probe Array PERFORMANCESENSOR ACCURACY Individual sensor accuracy: ±2% of reading from 0-5000 FPM SYSTEM ACCURACY Complete system accuracy: ±3% of reading over published velocity range¹VELOCITY RANGEFan inlet installations: 0-10,000 FPMSENSOR DESIGNPrecision matched, hermetically sealed thermistors with laser trimmed resistive heating elementEach sensor node consists of two (2) thermistors mounted in a dedicated flow conditioning aperature Each sensor node is completely sealed and impervious to water TEMPERATURE ACCURACY ±0.1°F over operating range of -20°F to 140°F SENSOR CAPACITY TRANSMITTER Maximum of 32 sensors per transmitterSENSOR DENSITY FAN INLETSingle or dual sensor configuration per inlet availablePROBEMATERIALS OF CONSTRUCTION 6063 anodized aluminum, 1⅛" diameter with remote NEMA 4X poly enclosure OPERATING CONDITIONSFLUID TEMPERATURE -20°F to 140°FHUMIDITY0 to 100% RH, condensingWIRINGCONNECTIONS AVAILABLE OPTIONS• Watertight integral plenum rated cable attached to probe • Conduit opening with terminal blocksFAN INLETStainless steel tube in tube telescoping support struts and stainless steel mounting bracketsELECTRA-flo 5 Series Thermal Airflow Measurement System, G5 Transmitter only A= Channel1 = Thermal dispersion airflow transmitter with graphicalLCD, two (2) programmable analog outputs and RS485 serial communications.2 = Dual channel thermal dispersion airflow transmitter withgraphical LCD, two (2) programmable analog outputs and RS485 serial communication.B= Enclosure *1 = NEMA 1 enclosure with cord grips2 = NEMA 4X SS enclosure w/o viewing window w/ cord grips3 = NEMA 4X fiberglass enclosure w/ viewing window & cord grips4 = NEMA 1 enclosure with conduit connection box5 = NEMA 4X SS enclosure w/o viewing window w/ conduit conn.6 = NEMA 4X fiberglass enclosure w/ viewing window & conduit conn.*Conduit connections required for outdoor transmitter installations C= Outputs2 = Two (2) analog outputs and one (1) alarm output D = Communications 1 = RS485E = Input Power1 = 24 V AC/DC (Up to 24 sensors)2 = 24 V AC/DC (25 to 32 sensors)F=Wiring Connection (A=1 use 1-4, A=2 use A-J)1 = Mini-DIN, XMTR to probe, 10ft 2 = Mini-DIN, XMTR to probe, 25ft 3 = Mini-DIN, XMTR to probe, 50ft 4 = Mini-DIN, XMTR to probe, 100ftA = Mini-DIN, XMTR to probe, 10ft & 10ftB = Mini-DIN, XMTR to probe, 10ft & 25ftC = Mini-DIN, XMTR to probe, 10ft & 50ftD = Mini-DIN, XMTR to probe, 10ft & 100ftE = Mini-DIN, XMTR to probe, 25ft & 25ftF = Mini-DIN, XMTR to probe, 25ft & 50ftG = Mini-DIN, XMTR to probe, 25ft & 100ftH = Mini-DIN, XMTR to probe, 50ft & 50ftI = Mini-DIN, XMTR to probe, 50ft & 100ftJ = Mini-DIN, XMTR to probe, 100ft & 100ft SPC=Special Config 000 = None 101 = SS TagsMODEL SELECTION GUIDEModel Number Coding = E-flo G5-AB-CDEF-(SPC)Model Number Coding = E-flo/S5-AABC-DDEF-GGHH-(SPC)ELECTRA-flo 5 Series Thermal Airflow Measurement System, Probe Array OnlyAA = Probe Mounting Style R1 = External mount, rectangular R2 = Internal mount, rectangular R3 = Internal stand-off mount, rectangular 2C1 = External mount, circular C2 = Internal mount, circular B = Maximum Probe Length (in inches) C = Adjacent Side (in inches)DD = Probe Level (Based on Straight Run)L0 = Level 0 (Between 2 & 3)L1 = Level 1 (Minimum Straight Run Requirements)L2 = Level 2L3 = Level 3 (Maximum Straight Run Requirements)LC = Custom Density E = Material of Construction Probes1 = 6063 Annodized Al., 1⅛" dia. with NEMA 1 cast aluminum enclosure.2 = 6063 Annodized Al., 1⅛" dia. with NEMA4 cast aluminum enclosure.F= Wiring Connections Probe to Probe *1 = Mini-DIN, NEMA 1 (For E = 1 only)3 = Conduit w/ terminal blocks (Optional for E=2)4 = IP68 liquid tight cord grips (Optional for E = 2)*Conduit connections required for outdoor probe installationsGG = Number of Sensors 101 - 32HH = Number of Probes 01 - 08A = Up to 18B = 18 to < 24C = 24 to < 30D = 30 to < 36E = 36 to < 44F = 44 to < 48G = 48 to < 54H = 54 to < 60I = 60 to < 66J = 66 to < 721 = 18 to < 262 = 26 to < 363 = 36 to < 424 = 42 to < 48K = 72 to < 84L = 84 to < 96M = 96 to < 108N = 108 to < 120O = 120 to < 132Max Probe Length - Rectangular Max Probe Length - Circular 5 = 48 to < 666 = 66 to < 847 = 84 to < 120A = Up to 18B = 18 to < 24C = 24 to < 30D = 30 to < 36E = 36 to < 44F = 44 to < 48G = 48 to < 54H = 54 to < 60I = 60 to < 66J = 66 to < 72K = 72 to < 84L = 84 to < 96M = 96 to < 108N = 108 to < 120O = 120 to < 1329 = CircularSPC=Special Config 000 = None 101 = SS TagsNotes 1. Maximum number of sensors (nodes) / probe is 82. Internal stand off mount in circular ducts is NOT allowedMODEL SELECTION GUIDE CONTINUEDMODEL SELECTION GUIDE CONTINUEDELECTRA-flo 5 Series Thermal Airflow Measurement System, Stations OnlyA = Probe Mounting StyleM = External mount in casing only, no cell C = External mount in casing with cellB = DamperM = No DamperD = With DamperC = Long Opening Dimension (in inches)A = 8 to 12B = > 12 to 24C = > 24 to 36D = > 36 to < 45E = 45 to 60F = > 60 to 72G = > 72 to 84H = > 84 to 96I = > 96 to 108J = > 108 to 120K = > 120 to 132D = Short Opening Dimensions (in inches)A = 8 to 12B = > 12 to 24C = > 24 to 36D = > 36 to < 45E = 45 to 60F = > 60 to 72G = > 72 to 84H = > 84 to 96I = > 96 to 108J = > 108 to 120K = > 120 to 1329 = Circular E = Casing Material of Construction14ga = Rectangle, 18ga = Circular1 = 14ga. galvanized steel2 = 18ga. galvanized steelF = Casing Width (depth) Dimension (in inches)1 = 8 (Default for Rect. or Circ. with 1 probe)2 = 10 (Default for Circ. with 2 probes)3 = 12 (Default for Circ. with 3 probes)4 = 14 (Default for Circ. with 4 probes)6 = 24 (Required for ELECTRO-flo/CD)G = Flange Connection1 = 1½" 90 deg., Formed (required for rectangular)2 = 1" flange, 14ga., Welded (Circ up to 24")3 = 1½" flange, 14ga., Welded (Circ >24" to <45")4 = 3/16" x 2" bar stock, Welded (Circ ≥45")5 = Beaded edge, 18ga. C configuration (Circ 8" to 24") N = Non-standard flangeSPC = Special Configuration000 = None101 = SS Tags102 = NIST Traceable Calibration CertificateModel Number Coding = E-flo/AB-CD-EFG-(SPC)。
ICP DAS ET-87Pn-MTCP 产品快速入门指南说明书
Quick Start Guide forET-87Pn-MTCPMay 2014, Version 1.0.2Congratulations on purchasing ET-87Pn-MTCP - a Modbus TCP I/O expansion unit to expand I-87K series I/O modules and the most popular automation solution for remote monitoring and control application. This Quick Start Guide will provide informationneeded to get started. Please also consult the User Manual for detailed information on the setup and use of ET-87Pn-MTCP .In addition to this guide, the package includes the following items:ET-87Pn-MTCPSoftware Utility CDScrew Driver (ET-87P4-MTCP/ET-87P8-MTCP)(1C016)● ET-87Pn-MTCP Reference DocumentCD:\Napdos\Modbus\ET87Pn\Document\/pub/cd/8000cd/napdos/modbus/et87pn/document/● ET-87Pn-MTCP Website/root/product/solutions/pac/ipac/et-87pn-mtcp.html● ICP DAS Website/1Mounting the HardwareThe ET-87Pn-MTCP installation must provide proper ventilation, spacing, and groundingto ensure the equipment will operate as specified. A minimum clearance of 50mmbetween the ET-87Pn-MTCP and the top and bottom side of the enclosure panels mustbe provided.2Connecting to PC, Network and Setting up the Poweri. Connect PC to LAN1 port through a hub . The ET-87Pn-MTCP is equipped with RJ-45 Ethernet ports for connection to an Ethernet hub/switch and PC. You can also link directly the ET-87Pn to PC with an Ethernet cable.ii. Connect the +24 V DC power supply to PWR1 and GND terminals.3 Installing the Modbus UtilityThe Modbus Utility can be obtained from companion CD or ICP DAS FTP site:CD:\Napdos\Modbus\Modbus_Utility\ftp:///pub/cd/8000cd/napdos/modbus/modbus_utility/4Using the Modbus Utility to Assign a New IP AddressUDP Search of the Modbus Utility can be used to configure the IP address. Before starting the configuration process, ensure that the LAN1 are used to connect to network and make the controller under the running firmware mode . The default IP addresses are as follows:Item IP Address 192.168.255.1 Subnet Mask255.255.0.0Gateway192.168.0.1Step 1: Run the Modbus Utility, and then search the ET-87Pn-MTCP.i. Double-click the Modbus Utility shortcut on the desktop. ii. Select UDP Search from the Client Tools menu.iii. Click the Search Servers button of the eSearch Utility dialog, waiting for the search to be done.Step 2: Configure IP Address. i. Select the “Name” field from the default IP address row ofET-87Pn-MTCP . ii. Click the Configuration (UDP) button to open the setting dialog.iii. Configure the IP settings. iv. Click the OK button to save theconfiguration.5Inserting and Wiring the I/O ModulesThere are various types of I/O expansion modules for interfacing many different field devices to the ET-87Pn-MTCP .For more information about I/O expansion module, please refer to/products/PAC/xpac/remote_io_support_list.htmii. Click the Configuration (UDP) button.iv. Click the OK button.6Using the Modbus Utility to Configure the ModuleThe Modbus Utility can be used to make the communication between the ET-87Pn-MTCP and PC/Laptop via the Modbus/TCP protocol.Step 1: Run the Modbus Utility and connect to ET-87Pn-MTCP. i. Double-click the Modbus Utility shortcut on the desktop. ii. Click the Modbus/TCP button in the middle of the Select Controller dialog.iii. Enter the IP address, and then click the Connect button.Enter the IP address, and then click the Connect button.Step 2: Match the I/O module and then get the I/O configuration information. i. Click the Refresh button to match the I/O modules to configuration of the controller.ii. Select the About option from the Help menu to get the I/O configuration and firmware information.iii. Check the module status diagram, ensuring for the I/O modules to be matched.i. Click the Refresh button. iii. See the module status diagram, ensuring for the I/O modules to be matched.Step 3: Set I/O configuration, get the I/O values and then save the I/Oconfiguration.i. Configure the I/O settings, such as Range Code, Power-on and Safe values.ii. Select the Timer Interval from the Monitor menu to set the monitoring interval.iii. Click the Monitor icon to start retrieving I/O values. The I/O values will beiv. Select File option from the Save menu and select a location where the configuration file is about to be saved. This operation can save the controller configuration and I/Osettings to an “ini” file, and the file can be loaded by Load function at the next time when using the same controller and I/O modules.。
弗瑞特说明书
弗瑞特说明书 Revised by Petrel at 2021SR系列操作手册智能型阀门电动执行机构FreetFluidControlCo.,Ltd注意：安装使用前，请确保认真完整地阅读和理解了本手册！SR系列执行器是一种新型的全智能电动阀门执行器，它不仅采用了独特的双密封结构，而且对于所有参数均可利用红外线设定器进行非侵入式设置。
独有的多项措施保证了SR执行器的安全性、可靠性和方便性。
本手册将介绍SR执行器的准备、安装、设置（包括对执行器的一级设定和二级设定）和故障诊断功能，目的是帮助用户更好地使用、维护SR执行器。
所有SR系列执行器符合以下标准：1.JB/T8219-1999工业过程测量和控制系统用电动执行机构2.GB4208-1993外壳防护等级（IP代码“IP68”）SR防爆型执行器符合以下标准：1.GB3836.1-2000爆炸性气体环境用电气设备“通用要求”2.GB3836.2-2000爆炸性气体环境用电气设备隔爆型“d”目录1安全准则................................................................. 错误!未指定书签。
2SR执行器的基本结构 ........................................... 错误!未指定书签。
3SR执行器的基本操作 ........................................... 错误!未指定书签。
3.1手动操作.............................................................. 错误!未指定书签。
3.2电动操作.............................................................. 错误!未指定书签。
选择就地／停止／远程操作....................................... 错误!未指定书签。
瑞尔科 Ruelco RQ-1 快速排气器说明书
OPERATIONThe Ruelco RQ-1 Hydraulic Quick Exhaust is designed to rapidly bleed the control pressure from an actuator or other hydraulic device. It is typically used on safety valves, control valves or other devices that must respond quickly when the control signals are removed. Its in-line design and three part construction make the quick exhaust easy to install and maintain. No special tools are needed for repair and assembly. The Ruelco RQ-1 will improve equipment operation and reduce maintenance time. FEATURES• Stainless steel construction• 1/4” NPT port connections• Durable polyurethane seal• Large Cv factor assures fast system response• Small compact designPHONE: 504-340-0055FAX: 504-340-0056 EMAIL:****************1209 DISTRIBUTORS ROW NEW ORLEANS, LA 70123DIMENSIONSPARTS LISTPHONE: 504-340-0055 FAX: 504-340-0056EMAIL:****************1209 DISTRIBUTORS ROW NEW ORLEANS, LA 70123ITEM QUANTITYDESCRIPTIONMATERIAL 1 1 CAP 316 ST. STL. 2* 1 BODY -O RING NITRILE 3* 1PISTON O -RING NITRILE 4* 1 SEAT O -RINGNITRILE 5 1 BALL TUNGSTEN CARBIDE 6 1 SPRING INCONEL X -750 7 1SPOOL ASSEMBLY316/17-4 ST. STL. 8 1 BODY 316 ST. STL. 9* 1 SPOOL O -RINGNITRILE 10 1 SEAT 316 ST. STL. 11* 2 BACK -UP RING TEFLON 121RETAINER RING316 ST. STL.SPECIFICATIONSREPAIR KIT• 18-007-000OTHER TEMPERATURE RANGES AND SEAL COMPOUNDS AVAILABLE UPON REQUEST* INDICATES ITEMS IN THE REPAIR KITORDERING CODEFEATURES• Stainless steel construction • 1/2” NPT port connections • Durable polyurethane seal • Large Cv factor assures fast system responsePHONE: 504-340-0055 FAX: 504-340-0056EMAIL:****************1209 DISTRIBUTORS ROW NEW ORLEANS, LA 70123DIMENSIONSOPERATIONThe Ruelco RQ -2 Hydraulic Quick Exhaust is designed to rapidly bleed the control pressure from an actuator or other hydraulic device. It is typically used on safety valves, control valves or other deices that must respond quickly when the control signs are removed. Its in -line design and three part construction make the quick exhaust easy to install and maintain. No special tools are needed for repair and assembly. The Ruelco RQ -2 will improve equipment operation and reduce maintenance time.PARTS LISTPHONE: 504-340-0055 FAX: 504-340-0056EMAIL:****************1209 DISTRIBUTORS ROW NEW ORLEANS, LA 70123SPECIFICATIONSREPAIR KIT• 18-008-000OTHER TEMPERATURE RANGES AND SEAL COMPOUNDS AVAILABLE UPON REQUEST* INDICATES ITEMS IN THE REPAIR KITORDERING CODEITEM QUANTITYDESCRIPTIONMATERIAL 1 1 CAP 17-4 PH ST. STL.2* 1 BODY O -RING NITRILE 3* 1 SEAT O -RING NITRILE 4* 1 PISTON O -RINGNITRILE 5* 1 BALL TUNGSTEN CARBIDE6 1 SPRING 316 ST. STL.7 1 SPOOL ASSEMBLY17-4 PH ST. STL. 8 1 BODY17-4 PH ST. STL.9* 1 SPOOL O -RING NITRILE 10 1 LARGE SPRING 316 ST. STL. 11* 2 BACK -UP RINGPTFE 121SEAT316 ST. STL.FEATURES• Stainless steel construction • 3/4” NPT port connections • Durable polyurethane seal • Large Cv factor assures fast system responsePHONE: 504-340-0055 FAX: 504-340-0056EMAIL:****************1209 DISTRIBUTORS ROW NEW ORLEANS, LA 70123DIMENSIONSOPERATIONThe Ruelco 3/4” npt Hydraulic Quick Exhaust is designed to rap-idly bleed the control pressure from an actuator or other hy-draulic device. It is typically used on safety valves, control valves or other deices that must respond quickly when the control signs are removed. Its in -line design and three part construction make the quick exhaust easy to install and maintain. No special tools are needed for repair and assembly. The Ruelco RQ -2 will improve equipment operation and reduce maintenance time.PARTS LISTPHONE: 504-340-0055 FAX: 504-340-0056EMAIL:****************1209 DISTRIBUTORS ROW NEW ORLEANS, LA 70123SPECIFICATIONSREPAIR KIT• 18-008-000OTHER TEMPERATURE RANGES AND SEAL COMPOUNDS AVAILABLE UPON REQUEST* INDICATES ITEMS IN THE REPAIR KITITEM QUANTITYDESCRIPTIONMATERIAL 1 1 CAP 316 ST. STL. 2* 1 BODY O -RING NITRILE 3* 1 SEAT O -RING NITRILE 4* 1 PISTON O -RINGNITRILE 5* 1 BALL TUNGSTEN CARBIDE6 1 SPRING 316 ST. STL.7 1 SPOOL ASSEMBLY17-4 PH ST. STL. 8 1 BODY 316 ST. STL.9* 1 SPOOL O -RING NITRILE 10 1 LARGE SPRING 316 ST. STL. 11* 2 BACK -UP RINGPTFE 121SEAT316 ST. STL.ORDERING CODE。
PE_PT500说明书2008版
PROTHERM 500 通用程序控制器 用户手册1． 入门操作1.1.2 控制旋钮2.用户界面简介所有的用户操作界面都有这种类型的外型。
用户等级系统负荷在线帮助3 功能按键及相应的显示（1） 手动/自动：切换到自动操作/手动操作3.2 2号功能按键－报警报警按照不同的颜色显示。
红色表示报警处于激活状态但未被确认。
示报警处于激活状态但是已经确认。
蓝色表示报警已经消除但未被确认。
当屏幕上有很多报警项显示时，向上或向下旋转调整旋钮，可以查看所有的确认报警按[Ack]菜单按钮，则所有红色报警将变成黄色，所有蓝色报警将消失，声音提示报警将被关闭。
报警历史记录当光标移动到[Treat.]键，按控制旋钮并旋转，将指针移到输入栏。
按控制旋钮后旋转，选择所需的工艺。
为了便于选择工艺，存储工艺时可采取特殊的编号方法，例如，渗氮工艺可从1编起向上累加，而渗碳工艺可从编起向下累减。
另外，可以移动光标指针到[___]，按控制旋钮，将会进入如下画面：操作[|<-]，[<-][->]和[->|]移动列表中的工艺。
选择想要的工艺号，相应的工艺就会显示在屏幕上。
3.3.2标题信息3.3.4在线渗碳扩散计算－材质的影响和相关数据输入值是热处理材料合金材料比例，单位是重量百分比。
心部碳含量(Core Carban)是指工件自身的C含量，是合金材料工件的特性。
3.3.5渗氮工艺的特殊选项[Diff]选项用来选择是否使用在线的渗氮层深计算。
同时注意前面的类型选旋转控制旋钮，输入相应合金元素重量百分比的值。
控制旋钮的操作是渐进回火温度（Tempering Temp.）是指渗碳后回火工艺温度，该值用于计算回3.3.7工艺编制表弹出的窗口列出了相应的选项:首先提供工艺段编制的基本信息。
输入[Chamber]选项，该选项决定了本工艺段的处理在哪个炉室进行。
在入时间作为该工艺段结束的标志。
例如，在选项[ends at]中输入了工艺段结束工艺段的设定点等相关参数输入方式如下图所示，可直接等于输入值，在碳势控制工艺段，会有一些额外的控制选项。
CN616TC1 电子流水桶控制器说明书
经济型1⁄4 DIN 6区PID温度控制器CN616系列是一类多功能6回路、基于微处理器的控制器，它旨在实现简便的前面板或远程设置和操作。
每个温区按照先后顺序进行扫描，并显示活动温区。
可锁定单个温区，以便进行监测。
每种仪器都可编程，以满足操作人员的以下需求：热电偶类型、温度单位、配置为锁定或非锁定的上限、下限或者上限／下限报警；带手动调整的自动调谐或手动PID设置。
操作人员可以设置温区显示扫描时间和斜坡／恒值。
断电时，参数和设定值都会保留。
提供密码保护，可防止对校准、PID设置和斜坡/恒值曲线参数的意外更改。
如果断电，控制器将保留全部最新参数并回到“RUN”（运行）模式。
所有CN616控制器都有RS232三线制串行通讯接口。
RS232程序能够监测多达10台通过菊花链连接在一起的仪器。
线路电压是120 Vac或240 Vac，可通过外部跳线组件选择。
通过使用方便的螺钉接线端插头，可在仪器背部进行电气连接。
CN616系列采用安全密码来保护设置。
可以在前面板上启用或者禁用该密码，并且可通过RS232接口更改密码。
校准通过前面板进行，并单独受密码保护。
可提供更高级别的密码。
这种仪器封装在1⁄4 DIN铝质外壳中，安装时不用将外壳拆下。
它安装在1⁄4 DIN 面板开孔中，并用滑动托架固定。
通过6个DC脉冲输出（每个温区1个）来控制该设备。
CN616系列U6回路PID控制器U自动调谐或手动调谐U加热或冷却控制U每个温区都有20段斜坡／恒值曲线参数U密码保护U用户可编程U标配RS232数字通讯接口U前面板校准U上限、下限或上限／下限报警，锁定或非锁定U可编程热电偶类型J、K、T、R、S、E、B或CU1⁄4 DIN铝质外壳U免费软件（兼容至Windows XP操作系统）CN616TC1，图片为实际尺寸。
提供一个单输出继电器，以指示任何温区中的报警条件。
该仪器通过闪烁主温度显示屏，同时闪烁报警温区编号来指示报警条件。
UPLC Quattro Premier标准操作规程(1)
目 录1开机步骤 (3)2准备UPLC (3)3建立一个新的Project (5)4ESI调谐 (7)4.1蠕动泵法 (7)4.2六通阀法 (15)5编辑质谱方法 (22)6编辑UPLC方法 (25)7样品表设置 (26)8运行样品 (28)9定量（Quanlynx/TargetLynx software） (29)10打印报告 (40)11仪器域值设置和质谱仪校正 (41)12自动调谐 (50)13使用APCI源 (58)14关机 (62)15UPLC/Quattro Premier使用注意事项 (63)1.开机步骤1.1.打开电脑，打开质谱电源和UPLC各电源，各部件通过自检后，点击MassLynx V4.0.lnk 进入工作站。
1.2.选择Instrument > MS Tune进入调谐页面。
1.3.从调谐页面选择Options> pump，打开真空泵，开始抽真空。
机械泵和分子涡轮泵开始工作。
1.4.质谱上的真空灯开始闪烁，当系统达到真空状态，灯变为绿色，不再闪烁。
如果达到实验状态大约要抽真空12小时1.5.气源压力设置氮气：90 – 120 psi 氩气：7 psi2.准备UPLC系统2.1.准备流动相 用0.22um的膜过滤缓冲液，所有的缓冲液和超纯水都要新配制，超纯水和缓冲液使用不得超过二天。
2.2.所有样品都要用流动相来溶解，并用0.22um的膜过滤。
2.3.初始化UPLC泵 在Masslynx主页面上选择 将 出现下面的画面。
2.4.点击 进入UPLC控制台，见下图。
2.5.湿灌注UPLC泵 选择CONTROL>Prime A/B solvent2.6.选择A1/B1或A2/B2 输入时间1min，如果更换了溶剂则输入3min,按star.2.7.初始化UPLC自动进样器 在UPLC控制台上选择Sample Manager 2.8.选择Control >> Prime syringes2.9.灌注进样器和流针系统。
SPRT思普瑞特 SP-EU1121嵌入式打印单元使用说明书
SP-EU1121嵌入式打印单元使用说明书VER1.05北京思普瑞特科技发展有限公司安全须知安全警告1）打印头为发热部件，打印过程中和打印刚结束时，不要触摸打印头以及周边部件。
2）不要触摸打印头表面和连接接插件，以免因静电损坏打印头。
注意事项1)打印单元应安装在一个平整、稳固的地方；2)在打印单元的周围留出足够的空间，以便操作和维护；3)打印单元应远离水源；4)不要在高温、潮湿以及污染严重的地方使用和保存打印单元。
避免阳光、强光和热源的直射；5)避免将打印单元放在有振动和冲击的地方；6)不允许潮湿的空气在打印单元的表面结露，如果已经形成，在露水消失之前不要打开打印单元的电源；7)将打印单元的电源适配器连接到一个适当的接地插座上；避免与大型电机或其它能够导致电源电压波动的设备使用同一插座；8)如果较长时间不使用打印单元，请断开打印单元电源适配器的电源；9)避免水或导电的物质进入打印单元内部，一旦发生，应立即关闭电源；10)打印单元不得在无纸的状态下打印，否则将严重损害打印胶辊和热敏打印头；11)为了保证打印质量和产品的寿命，建议采用推荐的或同等质量的纸张；12)在打印效果满足使用要求的情况下，建议用户尽可能设置低等级的打印浓度，以免影响打印头的使用寿命；13)用户不得自行拆卸打印单元进行检修。
目录简介 (4)第一章特点与性能 (5)1.1打印性能 (5)1.2打印纸 (5)1.3打印字符 (5)1.4接口形式 (5)1.5打印控制命令 (6)1.6电源要求 (6)1.7外形尺寸 (6)1.8工作环境 (6)1.9型号分类 (7)第二章操作说明 (8)2.1打印单元组成 (8)2.2纸的安装 (9)2.2.1上纸 (9)2.2.2切刀卡纸处理 (10)2.3接口连接 (10)2.3.1串行接口连接 (10)2.3.2电源连接 (11)2.4指示灯和按键操作 (11)2.5正常开机状态 (12)2.6自检测 (13)2.7十六进制打印 (13)2.8打印机参数设置 (13)2.9进入程序升级模式 (13)附录A:参数设置 (14)简介SP-EU1121嵌入式打印单元是一种新型行式热敏嵌入式打印机，具有易装纸、自动切纸、黑标侦测、打印速度快、高可靠性等特点，支持折叠纸，以及不同直径的纸卷。
Ruelco EX-1 快速排气阀说明书
RUELCO “EX-1” MANUAL VAVLE MODEL 1702OPERATION MANUALMANUAL # OMP- 1702 – 09 – 95 (SEE SPEC. SHEET 1702)I. PRINCIPLE OF OPERATIONThe Ruelco “EX-1” Quick Bleed isdesigned to rapidly exhaust thecontrol pressure from an actuator orother pneumatic devices. It istypically used on safety valves orother devices that must respondquickly when the control signals areremoved. Its in-line design and three(3) part construction make the quickbleed easy to install and maintain.No special tools are needed forrepair and assembly. The Ruelco“EX-1” will improve equipmentoperation and reduce maintenancetime.II. I NSTALLATIONThe “EX-1” can be mounted eithervertically or horizontally or supportedby piping from any of its ports. If it’ssupported by piping, care should betaken that the strength of the pipefitting used is adequate to preventthe fitting from breaking off in thevalve body should the valve beinadvertently struck.Proper pipe thread sealant shouldbe used on any pipe fittingsthreading into the valve ports. Ifstainless steel fittings are used, asealant that will prevent galling isrequired. Supply gas flowing throughthe valve body should be free oflarge dirt particles. If compressed airis used, it does not have to belubricated. If natural gas is used, itshould contain as little condensateas possible; this will extend the lifeof the bladder. III. DISASSEMBLY (REFER TO SPEC.SHEET 1702)Tools required are as follows:•¾” and 7/8” open end wrenchor suitable adjustablewrench.1) Place the ¾” wrench on thecenter spool (Item 1) andunscrew it from the body(Item 3). Remove the bladder(Item 2) from the centerspool.2) The bladder (Item 2) on thecenter spool (Item 1) maynow be replaced as perinstructions given in therepair section of this manual.3) The valve is now ready to becleaned and repaired.IV. REPAIR AND ASSEMBLY1) Using an appropriate safetysolvent, clean all parts.2) Verify that all bores are freeof burrs, nicks or dings.Closely examine the edgesof the holes in the body (Item3) and be sure that they arefree of burrs and/or sharpedges.3) Examine the edges of theholes on the center spool(Item 1) and verify that theyare smooth and free of burrs.4) The bladder (Item 2) shallhave an OD that is smoothand free of imperfections.5) Examine all threads forgouges or excessive wear.6) Replacement bladder sealfrom a Ruelco productrepair kit is required forproper valve performance. 7) Install the bladder onto thecenter spool. Verify that thebladder fits snug.8) Insert the center spool withbladder into the body andthread it as far as possible byhand.9) Using the ¾” and 7/8”wrenches, firmly tighten thecenter spool to the body.V. RECOMMENDEDMAINTENANCEPROCEDURE INTERVALOperateManually.Every30days.Disassemble and inspect. Yearly or as required.Replace seals. Every two (2) years or as required.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
谱瑞特智能排孔系统操作手册
（V1.02）
在使用本产品之前，请务必先详细阅读系统操作手册。
请在充分理解内容的基础上，正确使用。
DrilArrange ，Version 1.0 Copyright （C ）2014
目录
一、软件概述。
(3)
1.1 软件功能简介 (3)
1.2.1 工作界面 (3)
1.2.2 打开工作文件界面 (4)
1.3 菜单栏 (4)
1.3.1 文件菜单栏 (4)
1.3.2 编辑菜单栏 (5)
1.3.3视图菜单栏 (5)
1.3.4窗口菜单栏 (5)
1.3.5帮助菜单栏 (6)
1.4 常用工具栏 (6)
1.5 状态栏 (6)
二、快速使用指南。
(7)
2.1 准备加密狗。
(7)
2.2 解压软件包。
(7)
2.3 运行排孔程序。
(7)
2.4 打开文件。
(7)
2.5 检查曲线。
(8)
2.6 排孔参数的设置 (8)
2.6.1 选择填充方式 (8)
2.6.2 填充形状 (11)
2.6.3 设置小孔半径。
(11)
2.6.4 设置孔到边界距离。
(11)
2.6.5 设置孔孔之间的距离。
(11)
2.6.6 直线夹角（平行）设置。
(12)
2.6.7 轮廓精度（中线）设置。
(12)
2.6.8 沿轮廓线旋转。
(12)
2.7 命令执行按钮。
(13)
2.7.1生成 (13)
2.7.2 清除 (13)
2.8 灯数量 (13)
一、软件概述。
1.1 软件功能简介
谱瑞特智能排孔软件是一款专用于发光字制作的辅助软件。
该软件是在谱瑞特智能研发的专业排孔工具。
排孔方式有：轮廓排孔，平行排孔，网格排孔，中线排孔，单轮廓排孔，双轮廓排孔。
是一款灵活、快捷的冲孔字外露发光字的排版软件。
单孔灯由于容易坏，质量不稳定，目前采用四眼灯模组的冲孔发光字。
对于四眼灯的排孔而言，除了需要进行合理的布孔外，还需要旋转四眼灯的方向使其和发光字的轮廓平行。
如果说前面的单孔还可以手工排布的话，这个四眼灯的排孔手工就极为耗时了。
1.2.1 工作界面
1.2.2 打开工作文件界面
当打开工作文件时，软件菜单栏中增加编辑、窗口两个菜单栏。
1.3 菜单栏（示例状态为打开工作文件时状态，以下示例均为此状态。
）1.3.1 文件菜单栏
1.3.3视图菜单栏
1.3.4窗口菜单栏
撤 消；重 做； 局部调整；添加小孔； 删除实体
；平移实体
；
全局优化：对局部点进行均匀化，
避免有些点有些重叠。
平移视图；放大视图； 缩小视图；选择视图；
合适视图。
1.4 常用工具栏
打开（Ctrl+O）需要排孔的文件，目前支持常用的DXF、PLT、HPG格式的文件。
保存（Ctrl+S）已经排好文件。
已经保存好的文件还可以进行再次编辑。
撤消（Ctrl+Z）。
重做[恢复]（Ctrl+Y）。
恢复上次撤消的操作。
拼接曲线。
将曲线首尾拼合起来，形成一条曲线。
封闭曲线。
封闭导入的曲线，以实现排孔。
局部调整。
对个别排孔疏密不满意或不方便的地方进行选择，确认后进行再次排孔。
添加孔。
手动补充单个孔。
删除选中的实体。
删除被选中的孔，但不会删除原来的曲线。
平行实体。
平移被选中的孔。
平移视图。
放大视图
缩小视图
选择放大。
点击此图标后，按住鼠标左键选择要局部放大的区域。
合适视图。
当视图被放大或缩小到不易于观察时单击此图标，视图将回到最合适状态。
1.5 状态栏
正常情况下显示的是光标所在的坐标或是就绪。
当光标移动常用工具栏区域时，状态栏会分别显示当前光标所在的图标上的名
称。
如当光标移动到，则下方状态栏显示
二、快速使用指南。
2.1 准备加密狗。
将加密狗插入电脑USB接口，当加密狗中的绿灯闪烁时即可使用。
（注：使用本软件须将加密狗插入电脑USB接口中。
）
2.2 解压软件包。
本软件为绿色版，无须安装，解压即可使用。
（注：本软件一定要解压后再使用。
）2.3 运行排孔程序。
打开刚才解压后的软件包，双击运行排孔程序文件（下图中红圈标示的文件）。
（注：在运行本软件时，有部分杀毒软件会弹出阻止程序窗口，请选择“信任此程序”。
）
2.4 打开文件。
点击菜单栏中“文件”菜单，选择“打开”，在弹出的窗口中选择需要排孔的文件；或单击，在弹出的窗口中选择需要排孔的文件。
2.5 检查曲线。
有时候导入的曲线看似封闭的，其实没有闭合，这样的情况下是不能进行排孔操作的。
因此，我们对所要排孔的字进行检查。
步骤如下：
1，选中所要检查的字；
2，单击常用工具栏中图标；或者在“编辑”菜单中选取“拼接曲线”命令。
2.6 排孔参数的设置
2.6.1 选择填充方式
本软件提供了多达6种填充方式。
当选中其中之一时，该填充方式的图案的底色为黄色。
（注：当同一个文件中有多个字时，可以对这些字分别设置不同的填充方式。
但在对同一个选中的对象进行排孔操作时，不能同时选择两种及以上的填充方式。
）
1，轮廓填充方式：按照字的曲线方向进行排孔。
效果图如下：
2，平行填充方式：按照等距离的平行线进行排孔，此种填充方式较适合排大黑体字。
效果图如下：
3，网格填充方式：以网状的形式进行布孔。
效果图如下：
4，中线填充方式：以字的笔画的中间线为走向的布孔方式。
效果图如下：
5，单轮廓填充方式：按照字的围边形状进行布孔的方式。
效果图如下：
6，双轮廓排孔：按照字的围边形状进行两圈布孔。
效果图如下：
2.6.2 填充形状
本软件默认的填充形状为圆。
除常用的圆形以外，
软件还增加了支持个性化模板的功能。
根据实际加工需
要，可以在AUTOCAD中制作适合自己LED灯大小的模
板，以AUTOCAD 2000的格式保存于软件包“pattern”
文件夹中。
2.6.3 设置小孔半径。
度量单位为mm（毫米）。
（注：只有在填充形状选择为“圆”时，小孔半径的设置才生效，而其它的填充形状大小均以所选择模板的尺寸为标准。
）
2.6.4 设置孔到边界距离。
孔到边界距离是指孔边缘到字围边的距离。
当此项值设置为10时，如下图所示(CAD中演示)：
2.6.5 设置孔孔之间的距离。
孔孔之间的距离是指两个相邻孔边缘之间的距离。
当孔孔之间的距离设置为22时，如下图所示(CAD中演示)：
2.6.6 直线夹角（平行）设置。
此项设置在选择平行填充方式时有效，调节平行孔的走向与水平线的夹角。
当此项值设置为30时，如下图所示(CAD中演示)：
2.6.7 轮廓精度（中线）设置。
此项设置在选择中线填充方式时有效，确定中线到两边的距离的精度。
如下图所示(CAD中演示)：
2.6.8 沿轮廓线旋转。
此项设置是在排四眼灯时使用，增强排孔后的美观程度。
效果如下图。
2.7 命令执行按钮。
2.7.1生成
当点击生成按钮时，系统将对所选定的文字按照先前设定好的参数时行排孔。
2.7.2 清除
当点击“清除”按钮时，之前所有排好的孔将被全部清除，但不会清除原始图形。
2.8 灯数量
当点击“生成”按钮时，在灯数量的右侧会显示目前排孔的数量，而且孔数量随着手动调整数变动，便于及时了解到所需灯的数量及大概成本。
如下图所示：。