模具相关英语词汇大全(doc 25页)
(完整版)模具专业英文术语大全
模具英语专业术语模具述语一、入水：gate进入位： gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口： switching runner/gate唧嘴口径： sprue diameter二、流道: runner热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴： hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头： connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件： mold components 三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin顶针板：ejector retainner plate托板： support plate螺丝： screw管钉：dowel pin 开模槽：ply bar scot内模管位：core/cavity inter-lock顶针： ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cuton B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length 稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft 滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate 动模座板 moving clamp plate. bottom clamping plate. bottom plate上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate 垫块 spacer parallel支架 ejector housing. mould base leg 压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材 khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance 绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage针pin 物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity 接触长度contact length接触件电镀层contact plating 接触压力contact pressure 接触件中心距contact space 接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ，Ribbon cable柔性印刷电线Flexible printed wiring多层印制电路Multilayer printed circuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board，Double-sided board表面安装surface Mounting翘曲warp， bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plate A板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush 直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force 锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core 螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板11 / 17Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具标准翻译。
模具专业术语英语
模具专业术语英语
模具专业涉及许多专业术语，在英语中对应的词汇如下：
1. Mold/Mould: 模具
2. Die: 模具，尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴，注塑道
6. Gate: 浇口，进料口
7. Ejector Pin: 顶针，用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽，模具凹槽
这些词汇在模具制造和加工过程中经常使用，涵盖了模具设计、制造和加工等方面的专业术语。
模具生产常用英语词汇表
质量要求：钢材 的质量对模具的 寿命和精度有着 重要影响，需要 严格控制其成分
和性能。
加工工艺：钢材在 模具生产中需要进 行多道加工工序， 如切割、弯曲、钻 孔、热处理等，以 确保模具的质量和
精度。
铝合金
定义：铝合金是一种金属合金材料，由铝和其它合金元素组成 特性：铝合金具有轻质、高强度、耐腐蚀等特性，广泛用于制造模具 应用：铝合金在模具制造中主要用于制造模具框架、模座、模仁等部件 优点：铝合金模具具有使用寿命长、精度高、易加工等特点，能够提高生产效率和产品质量
添加副标题
模具生产常用英语词汇表
汇报人：
目录
CONTENTS
01 添加目录标题 03 模具部件
02 模具类型 04 模具材料
05 模具加工工艺
06 模具维修与保养
07 模具生产流程与管 理
添加章节标题
模具类型
成型模具
成型模具类型：注射成型模具、压缩成型模具、传递成型模具、挤出成型模具 注射成型模具：将塑料原料注入模具内，通过冷却定型后脱模取出制品 压缩成型模具：将塑料原料加入模具内，通过加热加压方式使原料成型 传递成型模具：将塑料原料加入模具内，通过加热加压方式使原料传递到另一模具内成型 挤出成型模具：将塑料原料加入模具内，通过加热加压方式使原料从模具口挤出，冷却定型后得到制品
T型螺栓（T-Bolts）
螺栓（Bolts）
垫圈（Gaskets）
螺柱（Studs）
膨胀螺栓（Anchor Bolts）
铆钉（Rivets）
生产中常用的 材料之一，具有 高强度、高硬度、 耐腐蚀等优点。
种类：包括碳素 钢、合金钢、不 锈钢等多种类型， 根据不同的模具 需求选择合适的
模具零件英语词汇
模具零件英语词汇3-plate mold 三板模2-plate mold 二板模leader pin/guide pin 边钉/导边bushing/guide bushing 边司/导套shoulder guide bushing 中托司guide pin 中托边ejector retainner plate 顶针板support plate 托板screw 螺丝dowel pin 管钉ply bar scot 开模槽core/cavity inter-lock 内模管位ejector pin 顶针ejector sleeve 司筒ejector pin 司筒针stripper plate 推板movable core,return core core puller 缩呵nylon latch lock 扣机（尼龙拉勾）lifter 斜顶mold base 模胚（架）cavity insert 上内模core insert 下内模slide 行位（滑块）insert 镶件wedge 压座/斜鸡wedge wear plate 耐磨板/油板plate 压条Lsupport pillar 撑头sprue bushing 唧嘴stop plate 挡板locating ring 定位圈latch 锁扣parting lock set 扣鸡push bar 推杆S.H.S.B 栓打螺丝eracuretun 顶板lever arm 活动臂spure sperader 分流锥bush 水口司stop pin 垃圾钉buffle 隔片spring rod 弹弓柱die spring 弹弓ejector guide bush 中托司ejector guide pin 中托边pin 镶针dowel pin 销子ball catch 波子弹弓pipe plug 喉塞lock plate 锁模块angle from pin 斜顶angle ejector rod 斜顶杆parting locks 尼龙拉勾lever arm 活动臂early return bar 复位键、提前回杆valves 气阀angle pin 斜导边terms 术语parting surface support balance 承压平面平衡parting line venting 模排气return pin and cavity interference 回针碰料位mold base shut hight 模总高超出啤机规格water line interferes withejector pin 顶针碰运水part from cavith (core) side 料位出上/下模cavity direct cut on A-plate,core direct cut on B-plate. 模胚原身出料位Do not use (core/cavity) insert 不准用镶件use beryllium copper insert 用铍铜做镶件preliinary (final) mold design 初步（正式）模图设计reverse core 反呵spring compressed length 弹弓压缩量good stability,stable 稳定性好insufficient rigidity 强度不够even cooling 均匀冷却sticking 扣模thero expansion 热膨胀tolorance 公差copper electrode 铜公(电极）top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location 定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block滑块sliding dowel block 滑块固定块active plate活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块mold [mEuld] n. 模子, 铸型vt. 浇铸, 塑造tooling [5tu:liN] v. 加工。
模具专业的英语词汇大全
模具专业的英语词汇大全一、模具基础词汇1. Mold 模具2. Die 冲模3. Core 核心模4. Cavity 型腔5. Mold Base 模架6. Mold Steel 模具钢7. Runner 流道8. Gate 进浇口9. Ejector Pin 顶针10. Ejector Plate 顶板二、模具设计相关词汇1. Draft Angle 脱模斜度2. Parting Line 分模线3. Radius 圆角4. Undercut 难以脱模的凹槽5. Slide 滑块6. Lifters 顶杆7. Cooling Channel 冷却水道8. Injection Point 注射点9. Shrinkage 收缩率10. Molding Cycle 成型周期三、模具加工与维护词汇1. Machining 加工2. Milling 铣削3. Grinding 磨削4. EDM (Electrical Discharge Machining) 电火花加工5. Wire Cutting 线切割6. Polishing 抛光7. Assembly 装配8. Maintenance 维护9. Repair 修理10. Replacement 更换四、模具材料与热处理词汇1. Tool Steel 工具钢2. Stainless Steel 不锈钢3. Aluminum 铝4. Plastic 塑料5. Rubber 橡胶6. Heat Treatment 热处理7. Hardness 硬度8. Tempering 回火9. Quenching 淬火10. Annealing 退火五、模具行业相关词汇1. Mold Maker 模具师傅2. Mold Designer 模具设计师3. Mold Manufacturer 模具制造商4. Injection Molding 注塑成型5. Blow Molding 吹塑成型6. Compression Molding 压缩成型7. Transfer Molding 传递成型8. Prototype Model 原型模具9. Mass Production 批量生产10. Quality Inspection 质量检验六、模具测试与质量控制词汇1. First Article Inspection 首件检查2. Sample 样品3. Defect 缺陷4. Dimensional Accuracy 尺寸精度5. Tolerance 公差6. Surface Finish 表面光洁度7. Stress Analysis 应力分析8. Flow Analysis 流动分析9. Mold Flow Simulation 模具流动模拟10. Quality Control 质量控制七、模具行业常用设备词汇1. Injection Molding Machine 注塑机2. Extruder 挤出机3. Blow Molding Machine 吹塑机4. CNC Machine 数控机床5. Lathe 车床6. Milling Machine 铣床7. Grinder 磨床8. EDM Machine 电火花机床9. Laser Cutter 激光切割机10. Robot 自动化八、模具生产流程词汇1. Design Drawing 设计图纸2. Mold Construction 模具构建3. Machining Process 加工工艺4. Tooling Setup 模具安装5. Trial Run 试模6. Adjustment 调整7. Production Run 生产运行8. Mold Maintenance 模具保养9. Mold Modification 模具修改10. Mold Recycling 模具回收九、模具行业认证与标准词汇1. ISO Certification ISO认证2. Quality Management System 质量管理体系3. Standard 标准化4. DIN 德国工业标准5. ASTM 美国材料与试验协会6. JIS 日本工业标准7. Certification Body 认证机构8. Audit 审核检查9. Compliance 符合性10. Continuous Improvement 持续改进十、模具行业发展趋势词汇1. Automation 自动化2. Intelligent Manufacturing 智能制造3. 3D Printing 三维打印4. Rapid Prototyping 快速原型5. Industry 4.0 工业4.06. Internet of Things (IoT) 物联网7. Big Data 大数据8. Cloud Computing 云计算9. Sustainable Development 可持续发展10. CrossIndustry Integration 跨行业整合通过这些词汇，我们可以看到模具行业不仅涉及具体的技术和操作，还包括了管理、质量控制、认证以及未来的发展趋势。
（完整word版）模具专业术语英文
（完整word版）模具专业术语英文注塑、模具专业英语Surface Appearance外观Glossiness/gloss finish光洁度、粗糙度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface玻纤外露、浮纤Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹、料花Flow mark流纹Brittle/brittleness脆、脆性Bubbles/trapped gas气泡/困气Void孔、气泡Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃等级V-2Poor dispersion分散不好FR/PTFE …agglomerates etc阻燃剂/PTFE…结块Pellet porous颗粒料孔隙、Low impact/tensile strength etc低冲击强度/拉伸强度等High flow/filler content etc高流动性/过度填充Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles纤维结团Product was rejected due to 产品不能接受因为…High moisture level高水分、高湿度Warpage/warped翘曲/变形Shrinkage/shrink收缩/收缩率Sink marks凹陷、缩水Short shot/short molding打不满、欠注Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边、披锋、溢边Discoloration变色Off color颜色差异Flow rate流动速率Viscous/viscosity粘性的、粘的/黏度High flow高流动Low flow低流动Sticky粘的，粘性的Sticking core粘后模，粘模芯Sticking sprue粘水口Sticking cavity粘前模Mold release（agent）脱模(剂)Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in extra …添加多一点…Reduced …content减少…含量Dropped/reduced …by x％减少…含量…％Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption预计年/月用量模具方面：Ejection system顶出系统、脱模系统pin顶针、推杆spring弹簧Gate type浇口类型Sprue主流道runner分流道cavity模腔Sprue gate直浇口Pin point gate点浇口Tab gate护耳浇口Fan gate 扇形浇口Tunnel or submarine gate潜伏式浇口Jump gate跳跃式浇口Diaphragm gate片状浇口Ring gate 环形浇口The cavity of the mould模腔Heated cylinder加热料筒Surface finish表面光洁度Sink mark缩水Air trap困气Gas trapped气体困着，困气void空隙，孔galling烧焦Weld line熔接痕，熔合线Drag mark划伤、脱模痕Scratch mark模具刮花Deformed/ warp变形Ejector not returned顶针不回位slide滑块、行位streak波纹、条纹、色痕delamination分层Jetting mark喷射痕Gate mark浇口痕rib筋、加强筋、骨位boss凸台、凸起、凸痕Melt flow length熔体流线长度Ejector plate顶针板Stop pin限位销Push rod推杆、顶针Push back pin复位杆Ejector guide pin顶针导柱Cold-slug-well冷料井、冷料穴plate模板Ejected mark顶痕，顶白nozzle喷嘴Surface defect表面缺陷Air vent排气口Filling uneven走胶不平衡、进胶不平衡pressure:压力speed:速度control:控制protection pressure:保压mold:模set:设定option:选择injection:射胶pressure reducing valve :减压阀relief valve:泄压阀max:最大max:最大system:系统proportional:比例pressure transducer:压力传感器sampling试模pressure sensor压力感应器AMP 伺服放大器trial runrunninggatedosage 溶胶clamp open 开模。
模具英语词汇
（二）Mould Tool
制模工具(gōngjù)词汇
第十一页，共50页。
adjustable spanner 活动扳手(bān shou) angle cutter 角铣刀 anvil 铁钻 arbour 心轴 backing 衬垫 belt sander 带式打磨机 buffing 抛光 chamfering machine 倒角机 chamfering tool 去角刀具 chisel 扁錾 chuck 夹具 compass 两角规 concave cutter 凹面铣刀 convex cutter 凸形铣刀 cross joint 十字接头 cutting edge clearance 刃口余隙角 drill stand 钻台 edge file 刃用锉刀
第五页，共50页。
撑头: support pillar 唧嘴： sprue bushing 挡板(dǎnɡ bǎn)：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝： 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pi
第十二页，共50页。
file 锉刀 flange joint 凸缘(tū yuán)接头 grinder 砂轮机 hammer 铁锤 hand brace 手摇钻 hatching 剖面线 hexagon headed bolt六角头螺栓 hexagon nut 六角螺帽 index head 分度头 jack 千斤 jig 治具 kit 工具箱 lapping 研磨 metal saw 金工锯 nose angle 刀角 pinchers 钳子 pliers 铗钳顶 plug 柱塞头 polisher 磨光器 protable driller 手提钻孔机
模具行业英语词汇大全
air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板aberration 色差bite 咬入blacking hole 涂料孔(铸疵)blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕range peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮摺叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱摺surging 波动torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿托木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理assembly drawing 装配图auto tool change cycle 自动换刀时间周期beam 横梁bending moment 弯矩bending stress 弯曲应力bottoming 底靠buckling 纵弯曲chamfering 去角斜切channel 凹槽chattering 颤动check point 查核点chip 切屑chip conveyor 排屑输送机coefficient of friction 摩擦系数compact 小型的cooling pipe 冷却管coupon 试样胚deflection 挠曲量distortion 扭曲变形draft taper 拔模锥度draw out 拉拔fit tolerance 配合公差flexible rigidity 弯曲刚性gas vent 气孔hatching 剖面线heater cooler 加热器冷却装置hook cavity 钩穴inching 寸动lug 凸缘maintenance 维修保固metallurgy 冶金学notch effect 切口效果out of roughness 真圆度performance 动作性能pit 坑plane strain 倒角应力plug mill 蕊棒轧管机repeated load 重覆载荷riveted joint 铆钉接合sand paper 砂纸shift 偏移shrink fit 热压配合shrinkage hole 缩孔sinking 凹陷sketch 草图spalling 剥落straightness 直度submarine 深陷式surface roughness 表面粗度tapping 攻螺丝thermocouple 热电耦torsion load 扭转载荷toughness 韧性tracing 描图under cut 凹割3D coordinate measurement 三次元量床3D modeling 三次元模拟aberration 色差abnormal glow 不规则辉光放电abrasive 砂轮access 通路accretion 炉瘤accurate die casting 精密压铸acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnance 酸性平炉activator 活化剂acetylene 乙炔adjustable spanner 活动扳手aerator 松砂机age hardening 时效硬化ageing 老化处理air hardening 气体硬化airless plasting cleaning 离心喷光air patenting 空气韧化air permeability test 透气性试验air set mold 常温自硬铸模air vent valve 通气阀all core molding 集合式铸模alloy tool steel 合金工具钢allround die holder 通用模型aluminium alloy 铝合金钢ampere 电流安培梢angle cutter 角铣刀angle welding 角焊angular pin 角梢angular pin 倾斜梢anode effect 阳极效应annealing 退火anchor pin 锚acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CAcellulose acetate butyrate 醋酸丁酸纤维素CABcomposite material 复合材料cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑胶epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetatecopolymer 乙烯-醋酸乙烯EV Aethylene-vinlacetatecopolyme 醋酸乙烯共聚物EV Afiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrenerigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPEmelamine resin 三聚氰胺酚醛树脂MFnitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑胶polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PApolybutyleneterephthalate 聚对苯二甲酸丁酯PBTpolycarbonate 聚碳酸酯PCpolyethyleneglycol 聚乙二醇PFGpolyethyleneoxide 聚氧化乙烯PEOpolyethyleneterephthalate 聚乙醇对苯PETPpolymetylmethacrylate 聚甲基丙烯酸甲酯PMMApolyoxymethylene 聚缩醛POMpolyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPOpolypropylene 聚丙烯PPpolystyrene 聚苯乙烯PSpolytetrafluoroethylene 聚四氟乙烯PTFEpolytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PEpolyurethane 聚氨基甲酸酯PUpolyvinylacetate 聚醋酸乙烯PV ACpolyvinylalcohol 聚乙烯醇PV Apolyvinylbutyral 聚乙烯醇缩丁醛PVBpolyvinylchloride 聚氯乙烯PVCpolyvinylfuoride 聚氟乙烯PVFpolyvinylidenechloride 聚偏二氯乙烯PVDCprepolymer 预聚物silicone resin 矽树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑胶unsaturated polyester 不饱和聚酯树脂activator 活化剂bag moulding 气胎施压成形bonding strength 黏合强度breathing 排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 著色剂color matching 调色color masterbatch 色母料compound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间ductility 延性elastomer 弹性体extruded bead sealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floating platen 活动模板foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injection plunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 後固化premix 预混料purging 清除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑胶片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clampingsystem 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率adjustable spanner 活动扳手angle cutter 角铣刀arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手back shaft 支撑轴blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车buckle 剥砂面camlachie cramp 铸包chamotte sand 烧磨砂charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼後熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部loader 供料器unloader 卸料机loop controller 闭回路控制器lower die 下模micro inching device 微寸动装置microinching equipment 微动装置moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床seamless forging 无缝锻造shave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slide balancer 滑动平衡器slug hole 逃料孔spin forming machine 旋压成形机spotting 合模stack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程take out device 取料装置toggle press 肘杆式压力机transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机vibration feeder 振动送料机wiring press 嵌线卷边机3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 冲孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程式制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机accretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace 酸性平炉aerator 松砂机air set mold 常温自硬铸模airless blasting cleaning 离心喷光all core molding 集合式铸模all round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand 背砂base bullion 粗金属锭base permeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔board drop hammer 板落锤bottom pour mold 底浇bottom pouring 底注boxless mold 脱箱砂模break-off core 缩颈砂心brick molding 砌箱造模法buckle 剥砂面camber 错箱camlachie cramp 铸包cast blade 铸造叶片casting flange 铸造凸缘casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂core template 砂心模板core vent 砂蕊排气孔corner gate 压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔die approach 模口角度draw out 锻造拔长draw plate 起模板draw spike 起模长针dummying 预锻embedded core 加装砂心erosion 冲砂fettling 铸件清理filling core 埋入砂心filling in 填砂film play 液面花纹finishing slag 炼後熔渣flash gutter 锻模飞边槽flask molding 砂箱造模forging roll 辊锻机formboard 进模口板gutter 锻模飞边槽hammer man 锻工heading machine 顶镦机impacter 卧式锻造机inblock cast 整体铸造ingot 铸锭ingot blank 铸坯inlay casting 镶铸法investment casting 失模铸造isothermal forging 恒温锻造loose piece 木模活块molding pit 铸模地坑pouring process 浇注法recasting 重铸roll forging 轧锻rolled surface 轧制表面rough sand 粗砂roughing forge 粗锻sand crushing 塌箱seamless forging 无缝锻造separate 分离shave 崩砂shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slag 熔渣slag inclusion 夹渣stickness 黏模性strip layout 带状胚料排样法tap casting 顶注top gate 顶注浇口unworked casting 不加工铸件upender 翻转装置upending 顶锻uphill casting 底铸white cast iron 白口铸件barrel 滚筒(加工)bending 波纹加工broaching 拉刀切削centering 定中心cutting 切削cylindrical lathe cutting 外圆车削electric discharge machine 放电加工electrolytic grinding 电解研磨embossing 压花加工facing 面车削filing 锉刀修润hand finishing 手工修润hemming 卷边加工hobbing 滚齿加工joggling 摇动加工lapping 抛光/研磨修润laser beam machining 雷射加工lathe cutting 车床车削planning 刨削加工polishing 抛亮光reaming 铰孔修润rough machining 粗切削rounding 圆形加工sawing 锯削scaling 清除钢碇缺陷shaping 成形加工skiving 表面研磨slotting 切缝切削taper turning 锥度车削thread cutting 螺纹切削ultrasonic machining 超音波加工up cut milling 逆铣加工abrasive 砂轮Al2O3 氧化铝borazon 氧化硼立方晶buffing wheel 抛光布轮diamond 钻石dresser 砂轮整修机dressing 修整endless grinding belt 循环式研磨带finishing allowance 加工余量grain 磨粒grinding disc 研磨盘jamp up 孔眼堵塞mesh 网筛目resinoid grinding wheel 半树脂型砂轮slitting 切缝量vitrified 陶瓷的。
模具英语3
第三课模具词汇：1. 螺纹：Screw thread2. 倒角: Chamfer3. R角: Radius4. 配模，FIT模：Mold fitting5. 模具设计 : Mold design6. 倒扣：Undercut7. 表面处理: Surface finish8. 蚀纹，晒纹：Texture9. 抛光, 省光: Polish, Gloss (SPI #)10. 涂层：Coating1.螺纹：Screw thread外螺纹：External thread内螺纹：Internal thread螺距：Pitch of thread2.倒角：Chamfer3. R角： Radius做倒角: Make chamfer45度 R角: 45 degree Radius4.配模，FIT模：Mold-fitting配模面：Mold-fitting surfaceFIT模红丹：Mold-fitting red paint5. 模具设计: Mold design6. 倒扣 :Undercut模具设计者: Mold designer, Engineer产品图: Part design (2d & 3d)此处有倒扣: Undercut here7-9.表面处理: Surface finish蚀纹: Texture, Etch, (EDM texture/finish) 省模: Gloss抛光: Polish镜面抛光：Mirror polish高光：High gloss喷沙: Sandblast雕刻: Engrave (Laser engraving)10.涂层：Coating镀铬涂层:Chrome coating镀镍涂层: Nickel coating镀钛涂层: Tin coating二.句子表达：1.可以取消此R角吗?Can we cancel (remove) this radius?最好可以取消此R角It’s better to cancel this radius.请取消此R角Please cancel this radius, ok? Thanks!Can we----It’s better—Please do sth.----,2.磨斜顶使它能平滑移动.Grind the lifter so that it can move smoothly.so that: 以便, 以求,以致,为了….与so as to意思差不多，可以说Grind the lifter so as to make it move smoothly.3.底部柱子表面抛光不够Polish on the boss of the bottom surface is not enough. On: prep. 在...之上, 依Of: [表示所属关系](属于)...的。
模具专业英语词汇
Here is a list of mold-related vocabulary in English:1. Mold -模具2. Mold cavity -模腔3. Mold core -模芯4. Mold base -模座5. Injection molding -注塑成型6. Blow molding -吹塑成型7. Compression molding -压缩成型8. Extrusion molding -挤出成型9. Rotational molding -旋转成型10. Thermoforming -热成型11. Mold design -模具设计12. Mold manufacturing -模具制造13. Mold making -模具加工14. Mold material -模具材料15. Mold steel -模具钢16. Mold release agent -脱模剂17. Mold temperature -模具温度18. Mold flow analysis -模流分析19. Mold maintenance -模具维护20. Mold repair -模具修复22. Mold polishing -模具抛光23. Molded part -注塑件24. Molded product -成型产品25. Molded surface -成型表面26. Molded feature -成型特征27. Ejector pins -顶出针28. Runner system -流道系统29. Cooling system -冷却系统30. Venting -通气31. Molded part defects -成型件缺陷32. Molded part warpage -成型件翘曲33. Molded part shrinkage -成型件收缩34. Mold release system -脱模系统35. Mold venting system -通气系统36. Mold temperature controller -模具温度控制器37. Mold gate -模具流道口38. Mold runner -模具流道39. Mold ejector system -模具顶出系统40. Mold clamping force -模具锁模力41. Mold shot size -模具射胶量42. Mold cycle time -模具循环时间44. Mold cooling time -模具冷却时间45. Mold release mechanism -模具脱模机构46. Molded part dimensions -成型件尺寸47. Molded part tolerance -成型件公差48. Molded part surface finish -成型件表面处理49. Molded part strength -成型件强度50. Molded part flexibility -成型件柔韧性51. Molded part accuracy -成型件精度52. Molded part durability -成型件耐久性53. Molded part weight -成型件重量54. Molded part texture -成型件纹理55. Molded part transparency -成型件透明度56. Molded part color -成型件颜色57. Molded part function -成型件功能58. Molded part assembly -成型件装配59. Molded part packaging -成型件包装60. Molded part labeling -成型件标记61. Molded part quality control -成型件质量控制62. Mold material selection -模具材料选择63. Mold design software -模具设计软件64. Mold manufacturing process -模具制造过程65. Mold injection molding machine -模具注塑机66. Mold blow molding machine -模具吹塑机67. Mold compression molding machine -模具压缩成型机68. Mold extrusion molding machine -模具挤出成型机69. Mold rotational molding machine -模具旋转成型机70. Mold thermoforming machine -模具热成型机71. Mold tooling -模具工装72. Molded part inspection -成型件检验73. Molded part packaging -成型件包装74. Molded part labeling -成型件标记75. Molded part storage -成型件存储76. Molded part transportation -成型件运输77. Molded part disposal -成型件处理78. Molded part recycling -成型件回收79. Molded part cost -成型件成本80. Molded part production rate -成型件生产率81. Molded part tooling cost -成型件工装成本82. Molded part tooling lead time -成型件工装交货期83. Molded part tooling lifespan -成型件工装寿命84. Molded part tooling maintenance -成型件工装维护85. Molded part tooling repair -成型件工装修复86. Molded part tooling modification -成型件工装修改87. Molded part tooling replacement -成型件工装更换88. Molded part tooling storage -成型件工装存储89. Molded part tooling transportation -成型件工装运输90. Molded part tooling disposal -成型件工装处理91. Molded part tooling recycling -成型件工装回收92. Molded part tooling cost estimation -成型件工装成本估算93. Molded part tooling design optimization -成型件工装设计优化94. Molded part tooling production planning -成型件工装生产计划95. Molded part tooling quality control -成型件工装质量控制96. Molded part tooling process improvement -成型件工装工艺改进97. Molded part tooling waste reduction -成型件工装废物减少98. Molded part tooling cost reduction -成型件工装成本降低99. Molded part tooling cycle time optimization -成型件工装循环时间优化100. Molded part tooling material selection -成型件工装材料选择101. Molded part tooling design validation -成型件工装设计验证102. Molded part tooling production monitoring -成型件工装生产监控103. Molded part tooling maintenance scheduling -成型件工装维护计划104. Molded part tooling repair process -成型件工装修复流程105. Molded part tooling modification process -成型件工装修改流程106. Molded part tooling replacement process -成型件工装更换流程107. Molded part tooling storage management -成型件工装存储管理108. Molded part tooling transportation logistics -成型件工装运输物流109. Molded part tooling disposal methods -成型件工装处理方法110. Molded part tooling recycling techniques -成型件工装回收技术111. Molded part tooling cost estimation tools -成型件工装成本估算工具112. Molded part tooling design optimization software -成型件工装设计优化软件113. Molded part tooling production planning systems -成型件工装生产计划系统114. Molded part tooling quality control methods -成型件工装质量控制方法115. Molded part tooling process improvement strategies -成型件工装工艺改进策略116. Molded part tooling waste reduction techniques -成型件工装废物减少技术117. Molded part tooling cost analysis -成型件工装成本分析118. Molded part tooling design review -成型件工装设计审查119. Molded part tooling production efficiency -成型件工装生产效率120. Molded part tooling maintenance checklist -成型件工装维护清单121. Molded part tooling repair cost estimation -成型件工装修复成本估算122. Molded part tooling modification cost estimation -成型件工装修改成本估算123. Molded part tooling replacement cost estimation -成型件工装更换成本估算124. Molded part tooling storage system -成型件工装存储系统125. Molded part tooling transportation cost calculation -成型件工装运输成本计算126. Molded part tooling disposal methods evaluation -成型件工装处理方法评估127. Molded part tooling recycling process optimization -成型件工装回收流程优化128. Molded part tooling cost reduction strategies -成型件工装成本降低策略129. Molded part tooling cycle time reduction techniques -成型件工装循环时间减少技术130. Molded part tooling material waste reduction -成型件工装材料废物减少131. Molded part tooling design validation methods -成型件工装设计验证方法132. Molded part tooling production monitoring tools -成型件工装生产监控工具133. Molded part tooling maintenance scheduling software -成型件工装维护计划软件134. Molded part tooling repair process optimization -成型件工装修复流程优化135. Molded part tooling modification process improvement -成型件工装修改流程改进136. Molded part tooling replacement process optimization -成型件工装更换流程优化137. Molded part tooling storage management techniques -成型件工装存储管理技术138. Molded part tooling transportation logistics optimization -成型件工装运输物流优化139. Molded part tooling disposal methods assessment -成型件工装处理方法评估140. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估141. Molded part tooling cost estimation software -成型件工装成本估算软件142. Molded part tooling design optimization tools -成型件工装设计优化工具143. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估144. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估145. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施146. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化147. Molded part tooling cost analysis tools -成型件工装成本分析工具148. Molded part tooling design review software -成型件工装设计审查软件149. Molded part tooling production efficiency evaluation -成型件工装生产效率评估150. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化151. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件152. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件153. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件154. Molded part tooling storage system optimization -成型件工装存储系统优化155. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件156. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具157. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术158. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施159. Molded partooling design validation methods -成型件工装设计验证方法160. Molded part tooling production monitoring tools -成型件工装生产监控工具161. Molded part tooling maintenance scheduling software -成型件工装维护计划软件162. Molded part tooling repair process optimization -成型件工装修复流程优化163. Molded part tooling modification process improvement -成型件工装修改流程改进164. Molded part tooling replacement process optimization -成型件工装更换流程优化165. Molded part tooling storage management techniques -成型件工装存储管理技术166. Molded part tooling transportation logistics optimization -成型件工装运输物流优化167. Molded part tooling disposal methods assessment -成型件工装处理方法评估168. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估169. Molded part tooling cost estimation software -成型件工装成本估算软件170. Molded part tooling design optimization tools -成型件工装设计优化工具171. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估172. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估173. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施174. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化175. Molded part tooling cost analysis tools -成型件工装成本分析工具176. Molded part tooling design review software -成型件工装设计审查软件177. Molded part tooling production efficiency evaluation -成型件工装生产效率评估178. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化179. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件180. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件181. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件182. Molded part tooling storage system optimization -成型件工装存储系统优化183. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件184. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具185. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术186. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施187. Molded part tooling risk assessment methods -成型件工装风险评估方法188. Molded part tooling safety protocols optimization -成型件工装安全协议优化189. Molded part tooling environmental impact assessment -成型件工装环境影响评估190. Molded part tooling sustainability evaluation -成型件工装可持续性评估191. Molded part tooling efficiency improvement strategies implementation -成型件工装效率提升策略实施192. Molded part tooling inventory management techniques -成型件工装库存管理技术193. Molded part tooling repair process optimization -成型件工装修复流程优化194. Molded part tooling modification cost reduction techniques -成型件工装修改成本降低技术195. Molded part tooling replacement cost reduction strategies -成型件工装更换成本降低策略196. Molded part tooling storage space optimization techniques -成型件工装存储空间优化技术197. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略198. Molded part tooling disposal methods optimization -成型件工装处理方法优化199. Molded part tooling recycling process evaluation -成型件工装回收流程评估200. Molded part tooling cost analysis techniques -成型件工装成本分析技术201. Molded part tooling design review process optimization -成型件工装设计审查流程优化202. Molded part tooling production efficiency improvement strategies -成型件工装生产效率提升策略203. Molded part tooling maintenance checklist evaluation -成型件工装维护清单评估204. Molded part tooling repair process efficiency improvement techniques -成型件工装修复流程效率提升技术205. Molded part tooling modification cost reduction strategies -成型件工装修改成本降低策略206. Molded part tooling replacement cost reduction techniques -成型件工装更换成本降低技术207. Molded part tooling storage system evaluation -成型件工装存储系统评估208. Molded part tooling transportation cost analysis techniques -成型件工装运输成本分析技术209. Molded part tooling disposal methods optimization strategies -成型件工装处理方法优化策略210. Molded part tooling recycling process efficiency improvement techniques -成型件工装回收流程效率提升技术211. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施212. Molded part tooling risk assessment techniques -成型件工装风险评估技术213. Molded part tooling safety protocols evaluation -成型件工装安全协议评估214. Molded part tooling environmental impact assessment techniques -成型件工装环境影响评估技术215. Molded part tooling sustainability improvement strategies -成型件工装可持续性改进策略216. Molded part tooling efficiency evaluation techniques -成型件工装效率评估技术217. Molded part tooling inventory management optimization -成型件工装库存管理优化218. Molded part tooling repair process efficiency evaluation -成型件工装修复流程效率评估219. Molded part tooling modification cost reduction strategies implementation -成型件工装修改成本降低策略实施220. Molded part tooling replacement cost reduction techniques implementation -成型件工装更换成本降低技术实施221. Molded part tooling storage space optimization strategies -成型件工装存储空间优化策略222. Molded part tooling transportation cost reduction techniques implementation -成型件工装运输成本降低技术实施223. Molded part tooling disposal methods optimization techniques -成型件工装处理方法优化技术224. Molded part tooling recycling process efficiency evaluation -成型件工装回收流程效率评估225. Molded part tooling cost analysis techniques implementation -成型件工装成本分析技术实施226. Molded part tooling design review process optimization strategies -成型件工装设计审查流程优化策略227. Molded part tooling production efficiency improvement techniques implementation -成型件工装生产效率提升技术实施228229. Molded part tooling quality control measures evaluation -成型件工装质量控制措施评估230. Molded part tooling inspection process optimization strategies -成型件工装检验过程优化策略231. Molded part tooling maintenance schedule development -成型件工装维护计划制定232. Molded part tooling repair cost analysis techniques -成型件工装修复成本分析技术233. Molded part tooling modification process efficiency improvement techniques implementation -成型件工装修改过程效率提升技术实施234. Molded part tooling replacement process cost reduction strategies implementation -成型件工装更换过程成本降低策略实施235. Molded part tooling storage system optimization -成型件工装存储系统优化236. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术实施237. Molded part tooling disposal methods evaluation -成型件工装处理方法评估238. Molded part tooling recycling process efficiency improvement techniques implementation -成型件工装回收流程效率提升技术实施239. Molded part tooling cost reduction strategies evaluation -成型件工装成本降低策略评估240. Molded part tooling risk assessment techniques implementation -成型件工装风险评估技术实施241. Molded part tooling safety protocols optimization strategies -成型件工装安全协议优化策略242. Molded part tooling environmental impact assessment techniques implementation -成型件工装环境影响评估技术实施243. Molded part tooling sustainability improvement strategies evaluation -成型件工装可持续性改进策略评估244. Molded part tooling efficiency evaluation techniques implementation -成型件工装效率评估技术实施245. Molded part tooling inventory management optimization strategies implementation -成型件工装库存管理优化策略实施246. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复流程效率评估技术247. Molded part tooling modification cost reduction strategies evaluation -成型件工装修改成本降低策略评估248. Molded part tooling replacement cost reduction techniques evaluation -成型件工装更换成本降低技术评估249. Molded part tooling storage space optimization strategies implementation -成型件工装存储空间优化策略实施250. Molded part tooling transportation cost reduction techniques evaluation -成型件工装运输成本降低技术评估251. Molded part tooling design optimization techniques implementation -成型件工装设计优化技术实施252. Molded part tooling production capacity evaluation -成型件工装生产能力评估253. Molded part tooling inspection methods improvement strategies -成型件工装检验方法改进策略254. Molded part tooling maintenance cost analysis techniques -成型件工装维护成本分析技术255. Molded part tooling repair process optimization strategies implementation -成型件工装修复过程优化策略实施256. Molded part tooling modification process cost reduction techniques -成型件工装修改过程成本降低技术257. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术258. Molded part tooling storage system efficiency improvement strategies implementation -成型件工装存储系统效率提升策略实施259. Molded part tooling transportation cost reduction strategies evaluation -成型件工装运输成本降低策略评估260. Molded part tooling disposal methods optimization techniques implementation -成型件工装处理方法优化技术实施261. Molded part tooling quality control measures implementation -成型件工装质量控制措施实施262. Molded part tooling material selection criteria evaluation -成型件工装材料选择标准评估263. Molded part tooling cost estimation techniques implementation -成型件工装成本估算技术实施264. Molded part tooling waste reduction strategies evaluation -成型件工装废料减少策略评估265. Molded part tooling energy consumption optimization techniques -成型件工装能源消耗优化技术266. Molded part tooling production cycle time reduction strategies evaluation -成型件工装生产周期缩短策略评估267. Molded part tooling training programs implementation -成型件工装培训计划实施268. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略269. Molded part tooling inspection frequency evaluation techniques -成型件工装检验频率评估技术270. Molded part tooling repair cost reduction strategies implementation -成型件工装修复成本降低策略实施271. Molded part tooling modification process efficiency evaluation techniques -成型件工装修改过程效率评估技术272. Molded part tooling replacement process cost reduction strategies -成型件工装更换过程成本降低策略273. Molded part tooling storage system organization techniques implementation -成型件工装存储系统组织技术实施274. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估275. Molded part tooling disposal methods cost evaluation techniques -成型件工装处理方法成本评估技术276. Molded part tooling quality assurance audits implementation -成型件工装质量保证审计实施277. Molded part tooling material sourcing optimization strategies -成型件工装材料采购优化策略278. Molded part tooling cost control measures implementation -成型件工装成本控制措施实施279. Molded part tooling waste management techniques evaluation -成型件工装废料管理技术评估280. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略281. Molded part tooling production planning optimization techniques implementation -成型件工装生产计划优化技术实施282. Molded part tooling training effectiveness evaluation techniques -成型件工装培训效果评估技术283. Molded part tooling maintenance cost reduction strategies evaluation -成型件工装维护成本降低策略评估284. Molded part tooling inspection methods optimization techniques -成型件工装检验方法优化技术285. Molded part tooling repair process cost reduction strategies implementation -成型件工装修复过程成本降低策略实施286. Molded part tooling modification process efficiency improvement techniques -成型件工装修改过程效率提升技术287. Molded part tooling replacement process safety protocols evaluation -成型件工装更换过程安全协议评估288. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略289. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术290. Molded part tooling disposal methods efficiency evaluation techniques -成型件工装处理方法效率评估技术291. Molded part tooling quality control system implementation -成型件工装质量控制系统实施292. Molded part tooling material selection process optimization strategies -成型件工装材料选择过程优化策略293. Molded part tooling cost estimation accuracy evaluation techniques -成型件工装成本估算准确度评估技术294. Molded part tooling waste reduction techniques implementation -成型件工装废料减少技295. Molded part tooling energy consumption monitoring system implementation -成型件工装能耗监测系统实施296. Molded part tooling production scheduling optimization strategies -成型件工装生产调度优化策略297. Molded part tooling training program development techniques -成型件工装培训计划开发技术298. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略299. Molded part tooling inspection frequency optimization techniques -成型件工装检验频率优化技术300. Molded part tooling repair process efficiency improvement strategies -成型件工装修复过程效率提升策略301. Molded part tooling replacement cost analysis techniques -成型件工装更换成本分析技术302. Molded part tooling storage system organization techniques -成型件工装存储系统组织技术303. Molded part tooling transportation safety protocols implementation -成型件工装运输安全协议实施304. Molded part tooling disposal methods cost analysis techniques -成型件工装处理方法成本分析技术305. Molded part tooling quality control system evaluation techniques -成型件工装质量控制系统评估技术306. Molded part tooling material selection process efficiency evaluation techniques -成型件工装材料选择过程效率评估技术307. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确度提升策略308. Molded part tooling waste management system implementation -成型件工装废料管理系统实施309. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术310. Molded part tooling production scheduling efficiency evaluationtechniques -成型件工装生产调度效率评估技术311. Molded part tooling training program effectiveness evaluation techniques -成型件工装培训计划效果评估技术312. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术313. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略314. Molded part tooling repair process cost analysis techniques -成型件工装修复过程成本分析技术315. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术316. Molded part tooling storage system space utilization techniques -成型件工装存储系统空间利用技术317. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略318. Molded part tooling disposal methods efficiency improvement strategies -成型件工装处理方法效率提升策略319. Molded part tooling quality control system implementation techniques -成型件工装质量控制系统实施技术320. Molded part tooling material selection process optimization techniques -成型件工装材料选择过程优化技术321. Molded part tooling cost estimation accuracy improvementtechniques -成型件工装成本估算准确度提升技术322. Molded part tooling waste reduction strategies implementation -成型件工装废料减少策略实施323. Molded part tooling energy consumption monitoring system optimization techniques -成型件工装能耗监测系统优化技术324. Molded part tooling production scheduling efficiency improvement strategies -成型件工装生产调度效率提升策略325. Molded part tooling training program development techniques -成型件工装培训计划开发技术326. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术327. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略328. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复过程效率评估技术329. Molded part tooling replacement cost analysis methods -成型件工装更换成本分析方法330. Molded part tooling storage system organization strategies -成型件工装存储系统组织策略331. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估332. Molded part tooling disposal methods cost analysis methods -成型件工装处理方法成本分析方法333. Molded part tooling quality control system effectiveness evaluation techniques -成型件工装质量控制系统效果评估技术334. Molded part tooling material selection process efficiency improvement strategies -成型件工装材料选择过程效率提升策335. Molded part tooling cost optimization techniques -成型件工装成本优化技术336. Molded part tooling maintenance record keeping methods -成型件工装维护记录保持方法337. Molded part tooling inspection checklist development techniques -成型件工装检查清单开发技术338. Molded part tooling repair process time reduction strategies -成型件工装修复过程时间减少策略339. Molded part tooling replacement frequency analysis methods -成型件工装更换频率分析方法340. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术341. Molded part tooling transportation route optimization strategies -成型件工装运输路线优化策略342. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术343. Molded part tooling quality control system auditing methods -成型件工装质量控制系统审核方法344. Molded part tooling material selection process cost analysis techniques -成型件工装材料选择过程成本分析技术345. Molded part tooling cost estimation error analysis techniques -成型件工装成本估算误差分析技术346. Molded part tooling waste reduction strategies implementation monitoring techniques -成型件工装废料减少策略实施监测技术347. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术348. Molded part tooling production scheduling optimization techniques -成型件工装生产调度优化技术349. Molded part tooling training program effectiveness evaluation methods -成型件工装培训计划效果评估方法350. Molded part tooling maintenance schedule flexibility strategies -成型件工装维护计划灵活性策略351. Molded part tooling design software proficiency assessment methods -成型件工装设计软件熟练度评估方法352. Molded part tooling cost reduction strategies implementation monitoring techniques -成型件工装成本降低策略实施监测技术353. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略354. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法355. Molded part tooling disposal methods regulatory compliance evaluation techniques -成型件工装处理方法合规性评估技术356. Molded part tooling quality control system training program development techniques -成型件工装质量控制系统培训计划开发技术357. Molded part tooling material selection process sustainability assessment methods -成型件工装材料选择过程可持续性评估方法358. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确性提升策略359. Molded part tooling waste management system implementation techniques -成型件工装废料管理系统实施技术360. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略361. Molded part tooling production scheduling flexibility analysis methods -成型件工装生产调度灵活性分析方法362. Molded part tooling training program effectiveness evaluation criteria -成型件工装培训计划效果评估标准363. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术364. Molded part tooling design optimization methods for reducing defects -成型件工装设计优化方法降低缺陷365. Molded part tooling cost estimation techniques for new product development -成型件工装成本估算技术新产品开发366. Molded part tooling storage system inventory tracking methods -成型件工装存储系统库存跟踪方法367. Molded part tooling transportation risk mitigation strategies -成型件工装运输风险缓解策略368. Molded part tooling disposal methods environmental sustainability evaluation techniques -成型件工装处理方法环境可持续性评估技术369. Molded part tooling quality control system documentation management techniques -成型件工装质量控制系统文件管理技术370. Molded part tooling material selection process sustainability improvement strategies -成型件工装材料选择过程可持续性改善策略371. Molded part tooling cost estimation error reduction techniques -成型件工装成本估算误差减少技术372. Molded part tooling waste reduction strategies effectiveness evaluation methods -成型件工装废料减少策略效果评估方法373. Molded part tooling energy consumption monitoring techniques -成型件工装能耗监测技术374. Molded part tooling production scheduling optimization tools -成型件工装生产调度优化工具375. Molded part tooling training program evaluation methods -成型件工装培训计划评估方法376. Molded part tooling maintenance schedule adjustment techniques -成型件工装维护计划调整技术377. Molded part tooling design software selection criteria -成型件工装设计软件选择标准378. Molded part tooling cost reduction strategies effectiveness evaluation methods -成型件工装成本降低策略效果评估方法379. Molded part tooling storage system organization tools -成型件工装存储系统组织工具380. Molded part tooling transportation risk mitigation measures -成型件工装运输风险缓解措施381. Molded part tooling disposal methods regulatory compliance monitoring techniques -成型件工装处理方法合规性监测技术382. Molded part tooling quality control system training program evaluation methods -成型件工装质量控制系统培训计划评估方法383. Molded part tooling material selection process cost-benefit analysis techniques -成型件工装材料选择过程成本效益分析技术384. Molded part tooling waste management strategies sustainability assessment methods -成型件工装废料管理策略可持续性评估方法385. Molded part tooling energy efficiency improvement measures -成型件工装能效改善措施386. Molded part tooling production scheduling optimization algorithms-成型件工装生产调度优化算法387. Molded part tooling training program effectiveness evaluation tools -成型件工装培训计划效果评估工具388. Molded part tooling maintenance schedule optimization models -成型件工装维护计划优化模型389. Molded part tooling design optimization techniques for improving product performance -成型件工装设计优化技术提高产品性能390. Molded part tooling cost estimation methods for budget planning -成型件工装成本估算方法预算规划391. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术392. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法393. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术394. Molded part tooling quality control system documentation control methods -成型件工装质量控制系统文件控制方法395. Molded part tooling material selection process sustainability evaluation criteria -成型件工装材料选择过程可持续性评估标准396. Molded part tooling cost estimation accuracy improvement techniques -成型件工装成本估算准确性改善技术397. Molded part tooling waste reduction strategies monitoring methods。
常用模具英语词汇
模具述语 一、入水：gate进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner热流道： hot runner, hot manifold 热嘴/冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line plug 喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件： mold components撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：sprue spreader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks活动臂：lever arm 复位键、提前回杆：early return bar三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L ：guide pin顶针板：ejector retainer plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar slot内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate缩呵：movable core, ret urn core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate 压条：plate气阀：valves 斜导边：angle pin 术语：terms承压平面平衡：parting surface support balance 模排气：parting line venting 回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut height 顶针碰运水：water line interferes with ejector pin 料位出上/下模：part from cavity (core) side 模胚原身出料位：cavity direct cut on A-plate, core direct cut on B-plate.不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert 初步（正式）模图设计：preliminary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability, stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thermo expansion公差：tolerance铜公(电极）：copper electrodeArrest biock storage area 挡块放置区Micrometer strorage area 分厘卡放置区Unprocessed copper 未处理铜工Processed copper 处理铜工Rough machine 粗加工Finish machine 精加工。
模具英语词汇表
模具英语词汇表Aabrasive grinding 强力磨削abrasive[☜'breisiv] a.磨料的, 研磨的absence ['✌bs☜ns] n.. 不在，缺席accessory[✌k'ses☜ri] n.附件accommodate[☜'k m☜deit] v. 适应accordingly[☜'k :di☠li] adv.因此,从而,相应地accuracy['✌kjur☜si] n精度,准确性actuate['✌ktjueit] vt.开动(机器), 驱动adequate['✌dikwit] a. 足够的adhesive[☜d'hi:siv] n. 粘合剂adjacent[☜'d✞eisnt] a. 邻近的adopt[☜'d pt] vt. 采用advance [☜d'v✌:ns] n.进步advisable [☜d'vaizbl] adj. 可取的agitate['✌d✞iteit] v. 摇动a large extent 很大程度algorithm ['✌l♈☜ri❆☜m] n. 算法align [☜'lain] v 定位，调准alignment[☜'lainm☜nt] n. 校直all-too-frequent 频繁allowance[☜'l☜uens] n. 容差, 余量alternate[' :lt☜nit]v.交替,轮流alternative[ :l't☜:n☜tiv] n. 替换物alternatively[ :l't☜:n☜tivli] ad. 做为选择, 也许aluminum[ ✌lju'minj☜m] n.铝ample['✌mpl] adj. 充足的analysis [☜'n✌l☜sis] n. 分析ancillary['✌nsil☜ri] a.补助的, 副的angular ['✌♈jul☜] adj. 有角的annealing[☜'li:li☠] n.退火aperture ['✌p☜t☞☜] n.孔applied loads 作用力appropriate [☜'pr☜uprieit] a. 适当的arc[a:k] n.弧, 弓形arise[☜'raiz] vi. 出现, 发生arrange[☜'reid✞] v. 安排article['a:tikl] n.制品, 产品ascertain[ ✌s☜'tein] vt. 确定, 查明assemble[☜'sembl] vt.组装attitude ['✌titju:d] n 态度auxiliary [ :♈'zilj☜ri]adj. 辅助的avoid[☜'v id] v.避免axis['✌ksis] n.轴axle['✌ksl] n.轮轴, 车轴Bbackup['b✌k ✈p] n. 备份batch [b✌t☞] n 一批bearing['b☪☜ri☠] n.轴承,支座bed[bed] n. 床身behavior[bi'heivj☜] n. 性能bench-work 钳工工作bend[bend] v.弯曲beneath[bi'ni: ] prep在···下bin [bin] n. 仓，料架blank [bl✌☠k] n. 坯料blank [bl✌☠k] v. 冲裁,落料blanking tool 落料模blast [bl✈st] n.一阵（风）blemish['blemi☞] n. 缺点, 污点bolster['b☜ulst☜] n. 模座,垫板boost[bu:st] n. 推进boring['b :ri☠] n.镗削, 镗孔bracket ['br✌kit] n. 支架brass [br✌s] n.黄铜break down 破坏breakage ['breikid✞] n.破坏bridge piecebrine[brain] n. 盐水brittle['britl] adv.易碎的buffer [b✈f☜] n.缓冲器built-in 内装的bulging [b✈ld✞i☠] n. 凸肚burr [b☜:] n. 毛刺bush [bu☞] n. 衬套bush[bu☞]n. 衬套by far (修饰比较级, 最高级)···得多, 最by means of 借助于Ccabinet ['k✌binit] n.橱柜call upon 要求carbide['ka:baid] n.碳化物carburizing['ka:bjureti☠] n. 渗碳carriage['k✌rid✞] n.拖板, 大拖板carry along 一起带走carry down over 从···上取下carry out 完成case hardening 表面硬化case[keis] n. 壳, 套cast steel 铸钢casting['ka:sti☠] n. 铸造,铸件category['k✌t☜♈☜uri] n. 种类caution ['k :☞☜n] n. 警告，警示cavity and core plates 凹模和凸模板cavity['k✌viti] n.型腔, 腔, 洞centre-drilling 中心孔ceramic[si'r✌mik] n.陶瓷制品chain doted line 点划线channel['t☞✌nl] n.通道, 信道characteristic[k✌r☜kt☜'ristik] n.特性check[t☞ek] v.核算chip[t☞ip] n.切屑, 铁屑chuck [t☞✈k] n.卡盘chute [☞u:t] n. 斜道circa ['s☜k☜:] adv. 大约circlip['s☜:klip] n.(开口)簧环circuit['s☜:kit] n. 回路, 环路circular supoport blockcirculate['s☜:kjuleid] v.(使)循环clamp [kl✌mp] vt 夹紧clamp[kl✌mp] n.压板clay[klei] n. 泥土clearance ['kli☜r☜ns] n. 间隙clip [klip] vt. 切断，夹住cold hobbing 冷挤压cold slug well 冷料井collapse[k☜'l✌ps] vi.崩塌, 瓦解collapsible[k☜'l✌ps☜bl] adj.可分解的combination [k mbi'nei☞☜n] n. 组合commence[k☜'mens] v. 开始, 着手commence[k☜'mens]v. 开始commercial [k☜'m☜:☞☜l] adj. 商业的competitive[k☜m'petitiv] a. 竞争的complementary[ k mpli'ment☜ri] a. 互补的complexity [kem'pleksiti] n.复杂性complicated['k mpl☜keitid] adj.复杂的complication [k mpli'kei☞☜n] n. 复杂化compression [k☜m'pre☞☜n] n.压缩comprise[k☜m'prais] vt.包含compromise['k mpr☜maiz] n. 妥协, 折衷concern about 关于concise[k☜n'sais] a. 简明的, 简练的confront[k☜n'fr✈nt] vt. 使面临connector[k☜'nekt☜] n. 连接口, 接头consequent['k nsikw☜nt] a. 随之发生的, 必然的console ['k nsoul] n.控制台consume [k☜n'sjum] vt. 消耗, 占用consummate [k☜n's✈meit] vt. 使完善container[k☜n'tein☜] n. 容器contingent[ken'tind✞☜nt] a.可能发生的contour['k☜ntu☜] n.轮廓conventional[k☜n'ven☞☜nl] a.常规的converge[k☜n'v☜:d✞] v.集中于一点conversant[k n'v☜:s☜nt] a. 熟悉的conversion[k☜n'v☜:☞☜n] n 换算, 转换conveyer[ken'vei☜] n. 运送装置coolant['ku:l☜nt] n. 冷却液coordinate [k☜u' :dnit] vt. (使)协调copy machine 仿形(加工)机床core[k :] n. 型芯, 核心corresponding [ka:ri'sp di☠] n.相应的counteract [kaunt☜'r✌kt] vt. 反作用,抵抗couple with 伴随CPU (central processing unit) 中央处理器crack[kr✌k ] v.（使）破裂，裂纹critical['kritikl] adj.临界的cross-hatching 剖面线cross-section drawn 剖面图cross-slide 横向滑板CRT (cathoder-ray tube) 阴极射线管crush[kr✈☞]vt.压碎cryogenic[ krai☜'d✞enik ]a.低温学的crystal['kristl] adj.结晶状的cubic['kju:bik] a. 立方的, 立方体的cup [k✈p] vt (使)成杯状, 引伸curable ['kjur☜bl] adj. 可矫正的curvature['k☜:v☜t☞☜] n.弧线curve [k☜:v] vt. 使弯曲cutter bit 刀头, 刀片cyanide['sai☜naid] n.氰化物Ddash [d✌☞] n. 破折号daylight ['deilait] n. 板距decline[di'klain] v.下落,下降,减少,deform[di'f :m] v. (使)变形demonstrate['dem☜streit ] v证明depict[di'pikt ] vt 描述deposit [di'p zit] vt. 放置depression[di'pre☞☜n] n. 凹穴descend [di'sent] v. 下降desirable[di'zair☜bl] a. 合适的detail ['diteil] n.细节，详情deterioration[diti☜ri:☜'rei☞☜n] n. 退化, 恶化determine[di't☜:min] v.决定diagrammatic[ dai☜gr☜'m✌tik].a.图解的，图表的dictate['dikteit] v. 支配die[dai] n.模具, 冲模, 凹模dielectric[daii'lektrik] n. 电介质die-set 模架digital ['did✞itl ] n.数字式数字, a.数字的dimensional[dddi'men☞☜nl] a. 尺寸的, 空间的discharge[dis't☞a:d✞] n.v. 放电, 卸下, 排出discharge[dis't☞a:d✞] v.卸下discrete [dis'cri:t] adj. 离散的,分立的dislodge[dis'l d✞] v. 拉出, 取出dissolution[dis☜'lu:☞☜n] n.结束distinct [dis'ti☠kt] a.不同的，显著的distort [dis'd :t] vt. 扭曲distort[dis't :t] vt. (使)变形, 扭曲distributed system 分布式系统dowel ['dau☜l] n. 销子dramatically [dr☜'m✌tikli] adv. 显著地drastic ['dr✌stik] a.激烈的draughting[dra:fti☠] n. 绘图draughtsman['dr✌ftsm☜n] n. 起草人drawing['dr :i☠] n. 制图drill press 钻床drum [dr✈m] n.鼓轮dual ['dju:☜l] adv. 双的，双重的ductility [d✈k'tiliti ] n.延展性dynamic [dai'n✌mik ] adj 动力的Eedge [ed✞] n .边缘e.g.(exempli gratia) [拉] 例如ejector [i'd✞ekt☜] n.排出器，ejector plate 顶出板ejector rob 顶杆elasticity[il✌'stisiti] n.弹性electric dicharge machining 电火花加工electrical discharge machining 电火花加工electrochemical machining 电化学加工electrode[i'lektr☜ud] n. 电极electro-deposition 电铸elementary [el☜'ment☜ri] adj.基本的eliminate[i'limineit] vt. 消除, 除去elongate[i'l ☠♈et] vt. (使)伸长, 延长emerge [i'm☜:d✞] vi. 形成, 显现emphasize['emf☜saiz] vt. 强调endeavor[en'dev☜] n. 尽力engagement[in'♈eid✞ment] n. 约束, 接合enhance[in'h✌ns] vt. 提高, 增强ensure [in'☞u☜] vt. 确保，保证envisage[in'vizid✞] vt.设想erase[i'reis] vt. 抹去, 擦掉evaluation[i'v✌lju ei☞☜n] n. 评价, 估价eventually[i'v☜nt☞u☜li ] adv.终于evolution[ev☜'lu:☞☜n] n.进展execution[eksi'kju:☞☜n] n. 执行, 完成execute ['ekskju:t] v. 执行exert [i♈'z☜:t] vt. 施加experience[iks'piri☜ns] n. 经验explosive[iks'pl☜usiv]adj.爆炸(性)的extend[eks'tend] v. 伸展external[eks't☜:nl] a. 外部的extract[eks'tr✌kt] v. 拔出extreme[iks'tri:m] n. 极端extremely[iks'tri:mli] adv. 非常地extremity[iks'tmiti] n. 极端extrusion[eks'tru:✞☜n] n. 挤压, 挤出FF (Fahrenheit)['f✌r☜nhait] n.华氏温度fabricate ['f✌brikeit] vt. 制作,制造facilitate [f☜'siliteit] vt帮助facility[f☜'siliti] n. 设备facing[feisi☠] n. 端面车削fall within 属于, 适合于fan[f✌n] n.风扇far from 毫不, 一点不, 远非fatigue[f☜'ti♈] n.疲劳feasible ['fi:z☜bl] a 可行的feature ['fi:t☞☜] n.特色, 特征feed[fi:d] n.. 进给feedback ['fi:db✌k] n. 反馈female['fi:meil] a. 阴的, 凹形的ferrule['fer☜l] n. 套管file system 文件系统fitter['fit☜] n.装配工, 钳工fix[fiks] vt. 使固定, 安装, vi. 固定fixed half and moving half 定模和动模flat-panel technology 平面(显示)技术flexibility[fleksi'biliti] n. 适应性, 柔性flexible['fleks☜bl] a. 柔韧的flow mark 流动斑点follow-on tool 连续模foregoing ['f :'♈☜ui☠]adj. 在前的,前面的foretell[f :'tell] vt. 预测, 预示, 预言forge[f :d✞] n. v. 锻造forming[f :mi☠] n. 成型four screen quadrants 四屏幕象限fracture['fr✌kt☞☜] n.破裂free from 免于Ggap[♈✌p] n. 裂口, 间隙gearbox['♈i☜b ks] n.齿轮箱general arrangementgovern['♈✈v☜n] v.统治, 支配, 管理grain [♈rein] n. 纹理graphic ['♈r✌fik] adj. 图解的grasp [♈r✌sp] vt. 抓住grid[♈rid] n. 格子, 网格grind[♈raind] v. 磨, 磨削, 研磨grinding ['♈raindi☠] n. 磨光,磨削grinding machine 磨床gripper[♈rip☜] n. 抓爪, 夹具groove[♈ru:v] n. 凹槽guide bush 导套guide pillar 导柱guide pillars and bushes 导柱和导套Hhandset['h✌ndset] n. 电话听筒hardness['ha:dnis] n.硬度hardware ['ha:dw☪☜] n. 硬件headstock['hedst k] n.床头箱, 主轴箱hexagonal[hek's✌♈☜nl] a. 六角形的, 六角的hindrance['hindr☜ns] n.障碍, 障碍物hob[h b] n. 滚刀, 冲头hollow-ware 空心件horizontal[h ri'z ntl] a. 水平的hose[h☜uz] n. 软管, 水管hyperbolic [haip☜'b lik] adj.双曲线的Ii.e. (id est) [拉] 也就是identical[ai'dentikl] a同样的identify [ai'dentifai] v. 确定, 识别idle ['aidl] adj.空闲的immediately[i'mi:dj☜tli] adv. 正好, 恰好impact['imp✌kt] n.冲击impart [im'pa:t] v.给予implement ['implim☜nt] vt 实现impossibility[imp s☜'biliti] n.不可能impression[im'pre☞☜n] n. 型腔in contact with 接触in terms of 依据inasmuch (as)[in☜z'm✈t☞] conj.因为, 由于inch-to-metric conversions 英公制转换inclinable [in'klain☜bl] adj. 可倾斜的inclusion [in'klu☞☜n] n. 内含物inconspicuous[ink☜n'spikju☜s] a. 不显眼的incorporate [in'k :p☜reit] v 合并,混合indentation[ inden'tei☞☜n ] n.压痕indenter[in'dent☜] n. 压头independently[indi'pein☜ntli] a. 独自地, 独立地inevitably[in'evit☜bli] ad. 不可避免地inexpensive[inik'spensiv]adj. 便宜的inherently [in'hi☜r☜ntli] adv.固有的injection mould 注塑模injection[in'd✞ek☞☜n] n. 注射in-line-of-draw 直接脱模insert[in's☜:t] n. 嵌件inserted die 嵌入式凹模inspection[in'spek☞☜n] n.检查,监督installation[inst☜'lei☞☜n] n. 安装integration [inti'♈rei☞☜n] n.集成intelligent[in'telid✞☜nt]a. 智能的intentionally [in'ten☞☜n☜li] adv 加强地，集中地interface ['int☜feis] n.. 界面internal[in't☜:nl] a. 内部的interpolation [int☜p☜'lei☞☜n] n.插值法investment casting 熔模铸造irregular [i'regjul☜] adj. 不规则的，无规律irrespective of 不论, 不管irrespective[iri'spektiv] a. 不顾的, 不考虑的issue ['isju] vt. 发布，发出Jjoint line 结合线Kkerosene['ker☜si:n] n.煤油keyboard ['ki:b :d ] n. 健盘knock [n k] v 敲，敲打Llance [la:ns] v. 切缝lathe[lei❆] n. 车床latitude ['l✌titju:d] n. 自由lay out 布置limitation[limi'tei☞☜n] n.限度,限制,局限(性) local intelligence局部智能locate [l☜u'keit] vt. 定位logic ['l d✞ik] n. 逻辑longitudinal['l nd✞☜'tju:dinl] a. 纵向的longitudinally['l nd✞☜'tju:dinl] a. 纵向的look upon 视作, 看待lubrication[lju:bri'kei☞☜n ] n.润滑Mmachine shop 车间machine table 工作台machining[m☜'☞i:ni☠] n. 加工made-to-measure 定做maintenance['meintin☜ns] n.维护,维修majority[m☜'d✞a:riti] n.多数make use of 利用male[meil] a. 阳的, 凸形的malfunction['m✌l'f✈☠☞☜n] n. 故障mandrel['m✌dtil] n.心轴manifestation[m✌nif☜s'tei☞☜n] n. 表现, 显示massiveness ['m✌sivnis ] 厚实，大块measure['me✞☜] n. 大小, 度量microcomputer 微型计算机microns['maikr n] n.微米microprocessor 微处理器mild steel 低碳钢milling machine 铣床mineral['min☜r☜l] n.矿物, 矿产minimize['minimaiz] v.把···减到最少, 最小化minute['minit] a.微小的mirror image 镜像mirror['mir☜] n. 镜子MIT(Massachusetts Institute of Technology) 麻省理工学院moderate['m d☜rit]adj. 适度的modification [m difi'kei☞☜n ] n. 修改, 修正modulus['m djul☜s] n.系数mold[m☜uld] n. 模, 铸模, v. 制模, 造型monitor ['m nit☜ ] v. 监控monograph['m n☜♈ra:f] n. 专著more often than not 常常motivation[m☜uti'vei☞☜n] n. 动机mould split line 模具分型线moulding['m☜udi☠] n. 注塑件move away from 抛弃multi-imprison mould 多型腔模Nnarrow['n✌r☜u] a. 狭窄的NC (numerical control ) 数控nevertheless[ nev☜❆☜'les] conj.,adv.然而,不过nonferrous['n n'fer☜s] adj.不含铁的, 非铁的normally['n :mli]adv.通常地novice['n vis] n. 新手, 初学者nozzle['n zl] n. 喷嘴, 注口numerical [nju'merikl] n. 数字的Oobjectionable [☜b'd✞ek☞☜bl] adj. 有异议的，讨厌的observe[☜b'z☜:v] vt. 观察obviously [' bvi☜sli] adv 明显地off-line 脱机的on-line 联机operational [ p☜'rei☞☜nl] adj.操作的, 运作的opportunity[ p☜'tju:niti] n. 时机, 机会opposing[☜'p☜uzi☠] a.对立的, 对面的opposite[' p☜zit] n. 反面a.对立的,对面的optimization [ ptimai'zei☞☜n] n.最优化orient [' :ri☜nt] vt. 确定方向orthodox [' : ☜d ks] adj. 正统的，正规的overall['☜uv☜r :l] a.全面的,全部的overbend v.过度弯曲overcome[☜uv☜'k✈m] vt.克服, 战胜overlaping['☜uv☜'l✌pi☠] n. 重叠overriding[☜uv☜'raidi☠] a. 主要的, 占优势的Ppack[p✌k] v. 包装package ['p✌kid✞] vt.包装pallet ['p✌lit] n.货盘panel ['p✌nl] n.面板paraffin['p✌r☜fin] n. 石蜡parallel[p✌r☜lel] a.平行的penetration[peni'trei☞☜n ] n.穿透peripheral [p☜'rif☜r☜l] adj 外围的periphery [p☜'rif☜ri] n. 外围permit[p☜'mit] v. 许可, 允许pressure casting 压力铸造pillar['pil☜] n. 柱子, 导柱pin[pin] n. 销, 栓, 钉pin-point gate 针点式浇口piston ['pist☜n] n.活塞plan view 主视图plasma['pl✌zm☜] n. 等离子plastic['pl✌stik] n. 塑料platen['pl✌t☜n] n. 压板plotter[pl t☜] n. 绘图机plunge [pl✈nd✞] v翻孔plunge[pl✈nd✞] v.投入plunger ['pl✈nd✞☜ ] n. 柱塞pocket-size 袖珍portray[p :'trei] v.描绘pot[p t] n.壶pour[p :] vt. 灌, 注practicable['pr✌ktik☜b] a. 行得通的preferable['pref☜r☜bl] a.更好的, 更可取的preliminary [pri'limin☜ri] adj 初步的，预备的press setter 装模工press[pres] n.压,压床,冲床,压力机prevent [pri'vent] v. 妨碍primarily['praim☜rili] adv.主要地procedure[pr☜'si:d✞☜] n.步骤, 方法, 程序productivity.[pr☜ud✈k'tiviti] n. 生产力profile ['pr☜ufail] n.轮廓progressively[pr☜'♈resiv] ad.渐进地project[pr☜'d✞ekt] n.项目project[pr☜'d✞ekt] v. 凸出projection[pr☜'d✞ek☞☜n] n.突出部分proper['pr p☜] a. 本身的property['pr p☜ti] n.特性prototype ['pr☜ut☜taip] n. 原形proximity[pr k'simiti] n.接近prudent['pru:d☜nt] a. 谨慎的punch [p✈nt☞] v. 冲孔punch shapper tool 刨模机punch-cum-blanking die 凹凸模punched tape 穿孔带purchase ['p☜:t☞☜s] vt. 买，购买push back pin 回程杆pyrometer[pai'n mit☜] n. 高温计Qquality['kwaliti] n. 质量quadrant['kw dr☜nt] n. 象限quantity ['kw ntiti] n. 量，数量quench[kwent☞] vt. 淬火Rradial['reidi☜l] adv.放射状的ram [r✌m] n 撞锤.rapid['r✌pid]adj. 迅速的rapidly['r✌pidli]adv. 迅速地raster['r✌st☜] n. 光栅raw [r :] adj. 未加工的raw material 原材料ream [ri:m] v 铰大reaming[ri:mi☠] n. 扩孔, 铰孔recall[ri'k :l] vt. 记起, 想起recede [ri'si:d] v. 收回, 后退recess [ri'ses] n. 凹槽,凹座,凹进处redundancy[ri'd✈nd☜nsi] n. 过多re-entrant 凹入的refer[ri'f☜:] v. 指, 涉及, 谈及reference['ref☜r☜ns] n.参照,参考refresh display 刷新显示register ring 定位环register['red✞st☜] v. 记录, 显示, 记数regrind[ri:'♈aind](reground[ri:'gru:nd]) vt. 再磨研relative['rel☜tiv] a. 相当的, 比较的relay ['ri:lei] n. 继电器release[ri'li:s] vt. 释放relegate['rel☜geit] vt. 把··降低到reliability [rilai☜'biliti] n. 可靠性relief valves 安全阀relief[ri'li:f] n.解除relieve[ri'li:v ]vt.减轻, 解除remainder[ri'meind☜] n. 剩余物, 其余部分removal[ri'mu:vl] n. 取出remove[ri'mu:v] v. 切除, 切削reposition [rip☜'zi☞☜n] n.重新安排represent[ repri'zent☜] v 代表,象征reputable['repjut☜bl] a. 有名的, 受尊敬的reservoir['rez☜vwa: ] n.容器, 储存器resident['rezid☜nt] a. 驻存的resist[ri'zist] vt.抵抗resistance[ri'zist☜ns] n.阻力, 抵抗resolution[ rez☜'lu:☞☜n] n. 分辨率respective[ri'spektiv] a.分别的,各自的respond[ris'p nd] v.响应, 作出反应responsibility[risp ns☜'biliti] n.责任restrain[ris'trein]v.抑制restrict [ris'trikt] vt 限制，限定restriction[ris'trik☞☜n] n. 限制retain[ri'tein] vt.保持, 保留retaining plate 顶出固定板reveal [ri'vil] vt.显示，展现reversal [ri'v☜sl] n. 反向right-angled 成直角的rigidity[ri'd✞iditi] n. 刚度rod[r d] n. 杆, 棒rotate['r☜uteit] vt.(使)旋转rough machining 粗加工rough[r✈f] a. 粗略的routine [ru:'ti:n] n. 程序rubber['r✈b☜] n.橡胶runner and gate systems 流道和浇口系统Ssand casting 砂型铸造satisfactorily[ s✌tis'f✌ktrili] adv. 满意地saw[a :] n. 锯子scale[skeil]n. 硬壳score[sk :] v. 刻划scrap[skr✌p] n.废料, 边角料, 切屑screwcutting 切螺纹seal[si:l] vt.密封secondary storagesection cutting plane 剖切面secure[si'kju☜] v.固定secure[si'kju☜] vt.紧固,夹紧,固定segment['se♈m☜nt] v. 分割sensitive['sensitiv]a.敏感的sequence ['si:kw☜ns] n. 次序sequential[si'kwen☞☜l] a.相继的seriously['si☜ri☜sli] adv.严重地servomechanism ['s☜:v☜'mek☜nizm] n.伺服机构Servomechanism Laboratoies 伺服机构实验室servomotor ['s☜:v☜m☜ut☜] n.伺服马达setter ['set☜] n 安装者set-up 机构sever ['sev☜] v 切断severity [si'veriti] n. 严重shaded[☞✌did] adj.阴影的shank [☞✌☠k] n. 柄.shear[☞i☜]n.剪,切shot[☞t] n. 注射shrink[☞ri☠k] vi. 收缩side sectional view 侧视图signal ['si♈nl] n.信号similarity[simi'l✌riti] n.类似simplicity[sim'plisiti] n. 简单single-point cutting tool 单刃刀具situate['sitjueit] vt. 使位于, 使处于slide [slaid] vi. 滑动, 滑落slideway['slaidwei] n. 导轨slot[sl t] n. 槽slug[sl✈♈] n. 嵌条soak[s☜uk] v. 浸, 泡, 均热software ['s ftw☪☜] n. 软件solid['s lid] n.立体, 固体solidify[s☜'lidifai] vt.vi. (使)凝固, (使)固化solution[s☜'lu:☞☜n] n.溶液sophisticated [s☜'fistikeitid] adj.尖端的,完善的sound[saund] a. 结实的, 坚固的)spark erosion 火花蚀刻spindle['spindl] n. 主轴spline[splain] n.花键split[split] n. 侧向分型, 分型spool[spu:l] n. 线轴springback n.反弹spring-loaded 装弹簧的sprue bush 主流道衬套sprue puller 浇道拉杆square[skw☪☜] v. 使成方形stage [steid✞] n. 阶段standardization[ st✌nd☜dai'zei☞☜n] n. 标准化startling['sta:tli☠] a. 令人吃惊的steadily['sted☜li ] adv. 稳定地step-by-step 逐步stickiness['stikinis] n.粘性stiffness['stifnis] n. 刚度stock[st k] n.毛坯, 坯料storage tube display 储存管显示storage['st :rid✞] n. 储存器straightforward[streit'f :w☜d]a.直接的strain[strein] n.应变strength[stre☠] n.强度stress[stres] n.压力,应力stress-strain应力--应变stretch[stret☞] v.伸展strike [straik] vt. 冲击stringent['strind✞☜nt ] a.严厉的stripper[strip☜] n. 推板stroke[strouk] n. 冲程, 行程structural build-up 结构上形成的sub-base 垫板subject['s✈bd✞ikt] vt.使受到submerge[s☜b'm☜:d✞] v.淹没subsequent ['s✈bsikwent] adj. 后来的subsequently ['s✈bsikwentli] adv. 后来, 随后substantial[s☜b'st✌n☞☜l] a. 实质的substitute ['s✈bstitju:t] vt. 代替,.替换subtract[s☜b'tr✌kt] v.减, 减去suitable['su:t☜bl] a. 合适的, 适当的suitably['su:t☜bli] ad.合适地sunk[s✈☠k](sink的过去分词) v. 下沉, 下陷superior[s☜'pi☜ri☜] adj.上好的susceptible[s☜'sept☜bl] adj.易受影响的sweep away 扫过symmetrical[si'metrikl] a. 对称的synchronize ['si☠kr☜naiz] v.同步,同时发生Ttactile['t✌ktail] a. 触觉的, 有触觉的tailstock['teilst k] n.尾架tapered['teip☜d] a. 锥形的tapping['t✌pi☠] n. 攻丝technique[tek'ni:k] n. 技术tempering['temp☜r☠] n.回火tendency['tend☜nsi] n. 趋向, 倾向tensile['tensail] a.拉力的, 可拉伸的, 拉紧的, 张紧的tension ['ten☞☜n] n.拉紧,张紧terminal ['t☜:m☜nl ] n. 终端机terminology[t☜:mi'n l☜d✞i ] n. 术语, 用辞theoretically [ i:☜'retikli ] adv.理论地thereby['❆☪☜bai] ad. 因此, 从而thermoplastic[' ☜:m☜u'pl✌stik] a. 热塑性的,n. 热塑性塑料thermoset[' ☜:m☜set] n.热固性thoroughly[' ✈r☜uli] adv.十分地, 彻底地thread pitch 螺距thread[ red] n. 螺纹thrown up 推上tilt [tilt] n. 倾斜, 翘起tolerance ['t l☜r☜ns] n..公差tong[t ☠] n. 火钳tonnage['t✈nid✞] n.吨位, 总吨数tool point 刀锋tool room 工具车间toolholder['tu:lh☜uld☜] n.刀夹,工具柄toolmaker ['tu:l'meik☜] n 模具制造者toolpost grinder 工具磨床toolpost['tu:l'p☜ust] n. 刀架torsional ['t :☞☜nl] a扭转的.toughness['t fnis] n. 韧性trace [treis] vt.追踪tracer-controlled milling machine 仿形铣床transverse[tr✌ns'v☜:s] a. 横向的tray [trei] n. 盘，盘子，蝶treatment['tri:tm☜nt] n.处理tremendous[tri'mend☜s] a. 惊人的, 巨大的trend [trend] n.趋势trigger stop 始用挡料销tungsten['t✈☠st☜n] n.钨turning['t☜:ni☠] n.车削twist[twist ] v.扭曲，扭转two-plate mould 双板式注射模Uultimately['✈ltimitli] adv终于.undercut moulding 侧向分型模undercut['✈nd☜k✈t] n. 侧向分型undercut['✈nd☜k✈t] n.底切underfeed['✈nd☜'fi:d] a, 底部进料的undergo[✈nd☜'♈☜u] vt.经受 1 underside['✈nd☜said] n 下面,下侧L undue[✈n'dju:] a.不适当的, 过度的uniform['ju:nif :m] a.统一的, 一致的utilize ['ju:tilaiz] v 利用Utopian[ju't☜upi☜n] adj.乌托邦的, 理想化的Vvalve[v✌lv] n.阀vaporize['veip☜raiz] vt.vi. 汽化, (使)蒸发variation [v☪☜ri'ei☞☜n] n. 变化various ['v☪☜ri☜s] a.不同的,各种的vector feedrate computation 向量进刀速率计算vee [vi:] n. v字形velocity[vi'l siti] n.速度versatile['v☜s☜tail] a.多才多艺的,万用的vertical['v☜:tikl] a. 垂直的via [vai☜] prep.经,通过vicinity[v☜'siniti] n.附近viewpoint['vju:p int] n. 观点Wwander['w nd☜] v. 偏离方向warp[w :p] v. 翘曲washer ['w ☞☜] n. 垫圈wear [w☪☜] v.磨损well line 结合线whereupon [hw☪☜r☜'p n] adv. 于是winding ['waindi☠] n. 绕, 卷with respect to 相对于withstand[wi❆'st✌nd] vt.经受,经得起work[w☜:k] n. 工件workstage 工序wrinkle['ri☠kl] n.皱纹vt.使皱Yyield[ji:ld] v. 生产Zzoom[zu:] n. 图象电子放大。
模具专业英语词汇.doc
模具专业英语词汇一、入水：gate进入位：gate location 水口形式：gate type大水口：edge gate 细水口：pin-point gate水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate 圆形流道：round (full/half runner)流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue 热流道板：hot manifold发热管：cartridge heater 探针: thermocouples插头：connector plug 插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug 喉管：tube塑胶管：plastic tube 快速接头：jiffy quick connectorplug/socker四、模具零件：mold components三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin顶针板：ejector retainner plate 托板：support plate螺丝：screw 管钉：dowel pin开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve司筒针：ejector pin 推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）：mold base 上内模：cavity insert下内模：core insert 行位（滑块）：slide镶件：insert 压座/斜鸡：wedge耐磨板/油板：wedge wear plate 压条：plate撑头: support pillar 唧嘴：sprue bushing挡板：stop plate 定位圈：locating ring锁扣：latch 扣鸡：parting lock set推杆：push bar 栓打螺丝：S.H.S.B顶板：eracuretun 活动臂：lever arm分流锥：spure sperader 水口司:bush垃圾钉：stop pin 隔片：buffle弹弓柱：spring rod 弹弓:die spring中托司：ejector guide bush 中托边：ejector guide pin镶针：pin 销子：dowel pin波子弹弓：ball catch 喉塞: pipe plug锁模块：lock plate 斜顶：angle from pin斜顶杆：angle ejector rod 尼龙拉勾：parting locks活动臂：lever arm 复位键、提前回杆：early return bar 气阀：valves 斜导边：angle pin五、术语：terms模排气：parting line venting模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity 均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance凸点：emboss凸圆：dome压线：groove重量：weight 展开图：extension dwg工程图：procedure dwg模具结构图：die structure dwg 材质：material料片厚度：material thickness 系数：factor向上：upward向下：downward适用模高：die height range 闭模高度：die height毛边：burr间隙：gap 总重量：total wt.上模重量：punch wt.圆线弹簧：lwire spring外导柱：outer guiding post铜公(电极）：copper electrode 简易模：plain die冲孔模：pierce die 成型模：forming die连续模：progressive die 冲孔：pierce抽孔：draw hole 折弯：bending切边：trim 剪断：shearing纸箱：Carton 木箱：Wooden Case盒：Box 塑料袋：Poly Bag六、注塑、模具专业英语外观：Surface Appearance光洁度、粗糙度：Glossiness/gloss毛面：finishMatt finish/matt surface表面析出：Blooming/surface blooming 表面白斑：White patches on surface 银纹：Silver marks/silver streak水纹、料花：Splay mark 流纹：Flow mark脆、脆性：Brittle/brittleness 气泡/困气：Bubbles/trapped gas孔、气泡：Void高流动性/过度填充：High flow/filler content etc 表面有小气泡/孔：Bristle/voids产品不能接受因为…：Product was rejected due to翘曲/变形：Warpage/warped收缩/收缩率：Shrinkage/shrink凹陷、缩水：Sink marks打不满、欠注：Short shot/short molding变形：Distortion尺寸过大：Over dimension尺寸过小：Under dimension飞边、披锋、溢边：Flashing变色：Discoloration粘性的、粘的/黏度：Viscous/viscosity高流动：High flow低流动：Low flow粘的，粘性的：Sticky粘后模，粘模芯：Sticking core 粘水口：Sticking sprue粘前模：Sticking cavity脱模(剂)：Mold release（agent）颜料染料：Pigment Dye接受产品规格：Accepted product specification认可我们的产品：Approved our product重新定标准：Re-set spec添加多一点…：Add in extra …减少…含量：Reduced … content 减少…含量…％：Dropped/reduced … by x％确认颜色标准：Confirmed color standard认可颜色标准：Approved color standard重新确认颜色标准：Re-confirmed color standard认可我们的产品：Qualified our product产品在测试当中：Product is under testing接了第一个定单：Received first order预计在…完成：Expected to finish by …预计定单量…吨：Expected order is xMT预计年/月用量：Estimated annual/monthly consumption七、模具方面：顶出系统、脱模系统：Ejection system 弹簧：spring浇口类型：Gate type直浇口：Sprue gate点浇口：Pin point gate 护耳浇口：Tab gate扇形浇口：Fan gate 潜伏式浇口：Tunnel or submarine gate 模腔：The cavity of the mould 加热料筒：Heated cylinder表面光洁度：Surface finish 缩水：Sink mark困气：Air trap冷料井、冷料穴：Cold-slug-well顶痕，顶白：Ejected mark 表面缺陷Surface defect排气口：Air vent走胶不平衡、进胶不平衡：Filling uneven 气体困着，困气：Gas trapped 烧焦：galling熔接痕，熔合线：Weld line 划伤、脱模痕：Drag mark模具刮花：Scratch mark 变形：Deformed/ warp顶针不回位：Ejector not returned 滑块、行位：slide波纹、条纹、色痕：streak 喷射痕：Jetting mark浇口痕：Gate mark 筋、加强筋、骨位：rib凸台、凸起、凸痕：boss 熔体流线长度：Melt flow length。
模具英语词汇
模具英语词汇abrasive grinding 强力磨削abrasive 磨料的,研磨的absence 不在，缺席accesssory 附件accommodate 适应accordingly 因此,从而,相应地accuracy 精度,准确性actuate 开动(机器),驱动adequate 足够的adhesive 粘合剂adjacent 邻近的adopt 采用advance 进步advisable 可取的agitate 摇动a large extent 很大程度algorithm 算法align 定位，调准alignment 校直all-too-frequent 频繁allowance 容差,余量alternate 交替,轮流alternatively 做为选择,也许aluminiun 铝ample 充足的analysis 分析ancillary 补助的,副的angular 有角的annealing 退火aperture 孔applied loads 作用力appropriate 适当的arc 弧,弓形arise 出现,发生arrange 安排article 制品,产品ascertain 确定,查明assemble 组装attitude 态度auxiliary 辅助的avoid 避免axis 轴axle 轮轴,车轴alternative 替换物backup 备份batch 一批bearing 轴承,支座bed 床身behavior 性能bench-work 钳工工作bend 弯曲beneath 在•••下bin 仓，料架blank 坯料blank 冲裁,落料blanking 落料模blast 一阵（风）blemish 缺点,污点bolster 模座,垫板boring 镗削,镗孔bracket 支架brass 黄铜break down 破坏breakage 破坏brine 盐水brittle 易碎的buffer 缓冲器built-in 内装的bulging 凸肚burr 毛刺bush 衬套by far •••得多,最by means of 借助于boost 推进cabinet 橱柜call upon 要求carbide 碳化物carburzing 渗碳carriage 拖板,大拖板carry along 一起带走carry down over 从•••上取下carry out 完成case hardening 表面硬化case 壳,套cast steel 铸钢casting 铸造,铸件category 种类caution 警告，警示cavity and core plates 凹模和凸模板cavity 型腔,腔,洞centre-drilling 中心孔ceramic 陶瓷制品chain doted line 点划线channel 通道,信道characteristic 特性check 核算chip 切屑,铁屑chuck 卡盘chute 斜道circa 大约circlip (开口)簧环circuit 回路,环路circulate (使)循环clamp 夹紧clamp 压板clay 泥土clearance 间隙clip 切断，夹住cold hobbing 冷挤压cold slug well 冷料井collapse 崩塌,瓦解collapsible 可分解的combination 组合commence 开始,着手commence 开始commercial 商业的competitive 竞争的complementary 互补的complexity 复杂性complication 复杂化compression 压缩comprise 包含compromise 妥协,折衷concern with 关于concise 简明的,简练的confront 使面临connector 连接口,接头consequent 随之发生的,必然的console 控制台consume 消耗,占用consummate 使完善container 容器contingent 可能发生的CPU (central processing unit) 中央处理器conventional 常规的converge 集中于一点conversant 熟悉的conversion 换算,转换conveyer 运送装置coolant 冷却液coordinate (使)协调copy machine 仿形(加工)机床core 型芯,核心corresponding 相应的counteract 反作用,抵抗couple with 伴随contour 轮廓crack （使）破裂，裂纹critical 临界的cross-hatching 剖面线cross-section drawn 剖面图cross-slide 横向滑板CRT (cathoder-ray tube) 阴极射线管crush 压碎cryogenic 低温学的crystal 结晶状的cubic 立方的,立方体的cup (使)成杯状,引伸curable 可矫正的curvature 弧线curve 使弯曲cutter bit 刀头,刀片cyanide 氰化物complicated 复杂的dash 破折号daylight 板距decline 下落,下降,减少deform (使)变形demonstrate 证明depict 描述deposite 放置depression 凹穴descend 下降desirable 合适的detail 细节，详情deterioration 退化,恶化determine 决定diagrammmatic 图解的，图表的dictate 支配die 模具,冲模,凹模dielectric 电介质die-set 模架digital 数字式数字dimensional 尺寸的,空间的discharge 放电,卸下,排出discharge 卸下discrete 离散的,分立的dislodge 拉出,取出dissolution 结束distinct 不同的，显著的distort 扭曲distort (使)变形,扭曲distributed system 分布式系统dowel 销子dramaticlly 显著地drastic 激烈的draughting 绘图draughtsman 起草人drawing 制图drill press 钻床drum 鼓轮dual 双的，双重的ductility 延展性dynamic 动力的edge 边缘e.g.(exempli gratia) [拉]例如ejector 排出器ejector plate 顶出板ejector rob 顶杆elasticity 弹性electric dicharge machining 电火花加工electrode 电极electro-deposition 电铸elementary 基本的eliminate 消除,除去elongate (使)伸长,延长emerge 形成,显现emphasise 强调endeavour 尽力engagement 约束,接合enhance 提高,增强ensure 确保，保证erase 抹去,擦掉evaluation 评价,估价eventually 终于evolution 进展excecution 执行,完成execute 执行electrochemical machining 电化学加工exerte 施加experience 经验explosive 爆炸(性)的extend 伸展external 外部的extract 拔出extreme 极端extremely 非常地extremity 极端extrusion 挤压,挤出envisage 设想Fahrenheit 华氏温度fabricate 制作,制造flat-panel technology 平面(显示)技术facility 设备facing 端面车削fall within 属于,适合于fan 风扇far from 毫不,一点不,远非fatigue 疲劳feasible 可行的feature 特色,特征feed 进给feedback 反馈female 阴的,凹形的ferrule 套管file system 文件系统fitter 装配工,钳工fix 使固定,安装fixed half and moving half 定模和动模facilitate 帮助flexibility 适应性,柔性flexible 柔韧的flow mark 流动斑点follow-on tool 连续模foregoing 在前的,前面的foretell 预测,预示,预言forge 锻造forming 成型four screen quadrants 四屏幕象限fracture 破裂free from 免于gap 裂口,间隙gearbox 齿轮箱govern 统治,支配,管理grain 纹理graphic 图解的grasp 抓住grid 格子,网格grind 磨,磨削,研磨grinding 磨光,磨削grinding machine 磨床gripper 抓爪,夹具groove 凹槽guide bush 导套guide pillar 导柱guide pillars and bushes 导柱和导套handset 电话听筒hardness 硬度hardware 硬件headstock 床头箱,主轴箱hexagonal 六角形的,六角的hindrance 障碍,障碍物hob 滚刀,冲头hollow-ware 空心件horizontal 水平的hose 软管,水管hyperbolic 双曲线的i.e. (id est) [拉]也就是identical 同样的identify 确定,识别idle 空闲的immediately 正好,恰好impact 冲击impart 给予implement 实现impossibility 不可能impression 型腔in contact with 接触in terms of 依据inasmuch (as) co因为,由于inch-to-metric conversions 英公制转换inclinable 可倾斜的inclusion 内含物inconspicuous 不显眼的incorporate 合并,混合indentation 压痕indenter 压头independently 独自地,独立地inevitably 不可避免地inexpensive 便宜的inherently 固有的injection mould 注塑模injection 注射in-line-of-draw 直接脱模insert 嵌件inserted die 嵌入式凹模inspection 检查,监督installation 安装integration 集成intelligent 智能的intentinonally 加强地，集中地interface 界面internal 内部的interpolation 插值法investment casting 熔模铸造irregular 不规则的，无规律irrespective of 不论,不管irrespective 不顾的,不考虑的issue 发布，发出joint line 结合线kerosene 煤油keyboard 健盘knock 敲，敲打lance 切缝lathe 车床latitude 自由lay out 布置limitation 限度,限制,局限(性) local intelligence 局部智能locate 定位logic 逻辑longitudinal 纵向的longitudinally 纵向的look upon 视作,看待lubrication 润滑machine shop 车间machine table 工作台machining 加工made-to-measure 定做maintenance 维护,维修majority 多数make use of 利用male 阳的,凸形的malfunction 故障mandrel 心轴manifestation 表现,显示massiveness 厚实，大块measure 大小,度量microcomputer 微型计算机microns 微米microprocessor 微处理器mild steel 低碳钢milling machine 铣床mineral 矿物,矿产minimise 把减到最少,最小化minute 微小的mirror image 镜像mirror 镜子moderate 适度的modification 修改,修正modulus 系数mold 模,铸模mold 制模,造型monitor 监控monograph 专著more often than not 常常motivation 动机mould split line 模具分型线moulding 注塑件move away from 抛弃multi-imprssion mould 多型腔模narrow 狭窄的NC (numerical control) 数控nevertheless 然而,不过nonferrous 不含铁的,非铁的normally 通常地novice 新手,初学者nozzle 喷嘴,注口numerical 数字的objectionable 有异议的，讨厌的observe 观察obviously 明显地off-line 脱机的on-line 联机operational 操作的,运作的opportunity 时机,机会opposing 对立的,对面的opposite 反面optimization 最优化orient 确定方向orthodox 正统的，正规的overall 全面的,全部的overbend 过度弯曲overcome 克服,战胜overlaping 重叠overriding 主要的,占优势的opposite 对立的,对面的pack 包装package 包装pallet 货盘panel 面板paraffin 石蜡parallel 平行的penetration 穿透peripheral 外围的periphery 外围permit 许可,允许pessure casting 压力铸造pillar 柱子,导柱pin 销,栓,钉pin-point gate 针点式浇口piston 活塞plan view 主视图plasma 等离子plastic 塑料platen 压板plotter 绘图机plunge 翻孔plunge 投入plunger 柱塞pocket-size 袖珍portray 描绘pot 壶pour 灌,注practicable 行得通的preferable 更好的,更可取的preliminary 初步的，预备的press setter 装模工press 压,压床,冲床,压力机prevent 妨碍primarily 主要地procedure 步骤,方法,程序productivity 生产力profile 轮廓progressively 渐进地project 项目project 凸出projection 突出部分proper 本身的property 特性prototype 原形proximity 接近prudent 谨慎的punch 冲孔punch shapper tool 刨模机punch-cum-blanking die 凹凸模punched tape 穿孔带purchase 买，购买push back pin 回程杆pyrometer 高温计quality 质量quandrant 象限quantity 量，数量quench 淬火radial 放射状的ram 撞锤rapid 迅速的rapidly 迅速地raster 光栅raw 未加工的raw material 原材料ream 铰大reaming 扩孔,铰孔recall 记起,想起recede 收回,后退recess 凹槽,凹座,凹进处redundancy 过多re-entrant 凹入的refer 指,涉及,谈及reference 参照,参考refresh display 刷新显示register ring 定位环register 记录,显示,记数regrind 再磨研relative 相当的,比较的relay 继电器release 释放relegate 把降低到reliability 可靠性relief valves 安全阀relief 解除relieve 减轻,解除remainder 剩余物,其余部分removal 取出remove 切除,切削reposition 重新安排represent 代表,象征reputable 有名的,受尊敬的reservoir 容器,储存器resident 驻存的resist 抵抗resistance 阻力,抵抗resolution 分辨率respective 分别的,各自的respond 响应,作出反应responsibility 责任restrain 抑制restrict 限制，限定restriction 限制retain 保持,保留retaining plate 顶出固定板reveal 显示，展现reversal 反向right-angled 成直角的rigidity 钢度rod 杆,棒rotate (使)旋转rough machining 粗加工rough 粗略的routine 程序rubber 橡胶runner and gate systems 流道和浇口系统sand casting 砂型铸造satisfactorily 满意地saw 锯子scale 硬壳score 刻划scrap 废料,边角料,切屑screwcutting 切螺纹seal 密封section cutting plane 剖切面secure 固定secure 紧固,夹紧,固定segment 分割sensitive 敏感的sequence 次序sequential 相继的seriously 严重地servomechanism 伺服机构servomotor 伺服马达setter 安装者set-up 机构sever 切断severity 严重shaded 阴影的shank 柄shear 剪,切shot 注射shrink 收缩side sectional view 侧视图signal 信号similarity 类似simplicity 简单single-point cutting tool 单刃刀具situate 使位于,使处于slide 滑动,滑落slideway 导轨slot 槽slug 嵌条soak 浸,泡,均热software 软件solid 立体,固体solidify (使)凝固solidify (使)固化solution 溶液sophisiticated 尖端的,完善的sound 结实的,坚固的spark erosion 火花蚀刻spindle 主轴spline 花键split 侧向分型,分型spool 线轴springback 反弹spring-loaded 装弹簧的sprue bush 主流道衬套sprue puller 浇道拉杆square 使成方形Servomechanism Laboratoies 伺服机构实验室stage 阶段standardisation 标准化startling 令人吃惊的steadily 稳定地step-by-step 逐步stickiness 粘性stiffness 刚度stock 毛坯,坯料storage tube display 储存管显示storage 储存器straightforward 直接的strain 应变strength 强度stress 压力,应力stress-strain 应力--应变stretch 伸展strike 冲击stringent 严厉的stripper 推板stroke 冲程,行程structrural build-up 结构上形成的sub-base 垫板subject 使受到submerge 淹没subsequent 后来的subsequently 后来,随后substantial 实质的substitute 代替,替换subtract 减,减去suitable 合适的,适当的suitably 合适地sunk 下沉,下陷superior 上好的susceptible 易受影响的sweep away 扫过symmetrical 对称的synchronize 同步,同时发生tactile 触觉的,有触觉的tailstock 尾架tapered 锥形的tapping 攻丝technique 技术tempering 回火tendency 趋向,倾向tensile 拉力的,可拉伸的tension 拉紧,张紧terminal 终端机terminology 术语,用辞theoretically 理论地thereby 因此,从而thermoplastic 热塑性的thermoplastic 热塑性塑料thermoset 热固性thoroughly 十分地,彻底地thread pitch 螺距thread 螺纹thrown up 推上tilt 倾斜,翘起tolerance 公差two-plate mould 双板式注射模tong 火钳tonnage 吨位,总吨数tool point 刀锋tool room 工具车间toolholder 刀夹,工具柄toolmaker 模具制造者toolpost grinder 工具磨床toolpost 刀架torsional 扭转的toughness 韧性trace 追踪transverse 横向的tray 盘，盘子，蝶treatment 处理tremendous 惊人的,巨大的trend 趋势trigger stop 始用挡料销tungsten 钨turning 车削twist 扭曲，扭转tracer-controlled milling machine 仿形铣床ultimately 终于undercut moulding 侧向分型模undercut 侧向分型undercut 底切underfeed 底部进料的undergo 经受underside 下面,下侧undue 不适当的,过度的uniform 统一的,一致的utilize 利用Utopian 乌托邦的,理想化的valve 阀vaporize 汽化vaporize (使)蒸发variation 变化various 不同的,各种的vector feedrate computation 向量进刀速率计算vee 字形velocity 速度versatile 多才多艺的,万用的vertical 垂直的via prep经,通过vicinity 附近viewpoint 观点wander 偏离方向warp 翘曲washer 垫圈wear 磨损well line 结合线whereupon 于是winding 绕,卷with respect to 相对于withstand 经受,经得起work 工件workstage 工序wrinkle 皱纹使皱yield 生产zoom 图象电子放大。
模具标件专业英语词汇
模具标件专业英语词汇一、模具（Mold）相关基础词汇。
1. Mold [məʊld] - 名词，模具；也可作动词，塑造，浇铸。
- 例句：This is a new type of injection mold.（这是一种新型的注塑模具。
）2. Die [daɪ] - 名词，冲模，钢模（在冲压工艺中使用）- 例句：The die is used for stamping metal sheets.（这个冲模用于冲压金属薄板。
）3. Cavity ['kævəti] - 名词，型腔；洞，凹处。
- 发音：['kævəti]- 例句：The cavity of the mold should be polished carefully.（模具的型腔应该仔细抛光。
）4. Core [kɔː(r)] - 名词，型芯；核心。
- 例句：The core is an important part of the mold.（型芯是模具的一个重要部分。
）二、模具标件（Standard Mold Components）词汇。
1. Guide Pin ['ɡaɪ d pɪn] - 名词，导柱。
- 例句：The guide pin helps to align the two parts of the mold.（导柱有助于使模具的两个部分对齐。
）2. Guide Bushing ['ɡaɪ d 'bʊʃɪŋ] - 名词，导套。
- 例句：The guide bushing is used in combination with the guide pin.（导套与导柱配合使用。
）3. Ejector Pin [i'dʒektə pɪn] - 名词，顶针。
- 例句：The ejector pin is used to push the finished product out of the mold.（顶针用于将成品从模具中顶出。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
模具相关英语词汇大全（doc 25页）組裝、衝壓、噴漆等專業詞匯Assembly line 組裝線Layout布置圖Conveyer流水線物料板Rivet table拉釘機Rivet gun拉釘槍Screw driver 起子Electric screw driver電動起子Pneumaticscrew driver氣動起子worktable 工作桌OOBA開箱檢查fit together組裝在一起fasten鎖緊(螺絲)fixture 夾具(治具)pallet棧板barcode條碼barcodescanner條碼掃描器fuse together熔合fuse machine熱熔機repair修理operator作業員QC品管supervisor 課長ME制造工程師MT製造生技cosmeticinspect外觀檢查inner partsinspect內部檢查thumb screw大頭螺絲lbs.inch鎊、英寸EMI gasket導電條|'plein|刨床miller銑床grinder磨床driller鉆床linear cutting 線切割electrical sparkle電火花welder電焊機staker=revitin g machine鉚合機position職務president董事長general manager總經理special assistant manager特助factorydirector廠長departmentdirector部長deputymanager|'depjuti|=vicemanager副理sectionsupervisor課長deputy sectionsupervisor=vice sectionsuperisor副課長groupleader/supervisor組長linesupervisor線長assistantmanager助理to move, tocarry, tohandle搬運be put instorage入庫pack packing包裝to apply oil擦油to file burr 銼毛刺finalinspection終檢to connectmaterial接料to reversematerial 翻料wet station沾濕台Tiana天那水cleaning cloth 抹布to load material上料to unload material卸料to return material/stock to退料scraped|'skræpid|報廢scrape ..v.刮;削deficient purchase來料不良manufacture procedure制程deficientmanufacturing procedure制程不良oxidation |'ksi'dei n|氧化scratch刮傷dents壓痕defectiveupsidingdown抽芽不良defective tostaking鉚合不良embededlump|in'bed||l mp|鑲塊feeding is notin place送料不到位stamping-missing漏沖productioncapacity生產力education andtraining教育與訓練proposalimprovement提案改善spareparts=buffer備件forklift叉車trailer=longvehicle拖板車compound die合模die locker鎖模器pressureplate=plate pinch壓板bolt螺栓name of a department部門名稱administratio n/general affairs dept總務部automatic screwdriver電動啟子thickness gauge厚薄規gauge(or jig)治具power wire電源線buzzle蜂鳴器defective product label 不良標簽identifyingsheet list標示單screwdriverholder起子插座pedal踩踏板stopper阻擋器flow board流水板hydraulichandjack油壓板車forklift叉車pallet棧板glove(s)手套glove(s) withexposedfingers割手套thumb大拇指forefinger食指midfinger中指ring finger無名指little finger小指band-aid創可貼iudustrialalcohol工業酒精alcoholcontainer沾濕台head ofscrewdriver起子頭sweeper掃把mop拖把vaccumcleaner吸塵器rag 抹布garbage container灰箕garbage can 垃圾箱garbage bag 垃圾袋chain鏈條jack升降機production line流水線chain鏈條槽magnetizer加磁器lamp holder 燈架to mop the floor拖地to clean the floor掃地to clean atable擦桌子air pipe 氣管packagingtool打包機packaging打包missing part漏件wrong part錯件excessivedefects過多的缺陷critical defect極嚴重缺陷major defect主要缺陷minor defect次要缺陷not up tostandard不合規格dimension/size is a littlebigger尺寸偏大(小)cosmeticdefect外觀不良slippedscrewhead/slippery screwhead螺絲滑頭slippedscrewhead/shippery screwthread滑手speckle斑點mildewed=moldy=mouldy發霉rust生銹deformation變形burr(金屬)flash(塑件)毛邊poor staking 鉚合不良excesssive gap 間隙過大grease/oil stains油污inclusion雜質painting peel off臟污shrinking/shri nkage縮水mixed color雜色scratch劃傷poor processing 制程不良poor incoming part事件不良fold ofpakaging belt打包帶折皺paintingmake-up補漆discoloration羿色water spots水漬polishing/surface processing表面處理exposedmetal/baremetal金屬裸露lack ofpainting烤漆不到位safety安全quality品質deliverydeadline交貨期cost成本engineering工程die repair模修enterpriseplan =enterpriseexpansionprojects企劃QC品管die worker模工production, toproduce生產equipment設備to start apress開機stop/switch off a press關機classification 整理regulation整頓cleanness清掃conservation 清潔culture教養qualified products,up-to-grade products良品defective products, not up-to-grade products不良品waste廢料board看板feeder送料機sliding rack滑料架defectiveproduct box不良品箱die change 換模to fix a die裝模to take aparta die拆模to repair a die修模packingmaterial包材basket蝴蝶竺plastic basket膠筐isolating platebaffle plate;barricade隔板carton box紙箱to pull andstretch拉深to putmaterial inplace, to cutmaterial, toinput落料to imposelines壓線to compress,compressing壓縮character die字模to feed,feeding送料transportation運輸(be)qualfied,up to grade合格not up to grade, not qualified不合格material change, stock change材料變更feature change 特性變更evaluation評估prepare for, make preparations for 準備parameters參數rotating speed, revolution轉速manufacturemanagement製造管理abnormalhandling異常處理productionunit生產單位lots ofproduction生產批量steel plate鋼板roll material捲料manufactureprocedure制程operationprocedure作業流程to revise,modify修訂to switch overto, switch---tothrow--overswitching over切換engineering,projectdifficulty工程瓶頸stage die工程模automation自動化to stake,staking,reviting鉚合addlubricating oil加潤滑油shut die架模shut height of a die架模高度analog-mode device類模器die lifter舉模器argon welding 氬焊vocabulary for stamping 衝壓常詞匯stamping, press沖壓punch press, dieing out press沖床uncoiler & strainghtener 整平機feeder送料機rack, shelf, stack料架cylinder油缸robot機械手taker取料機conveyer belt輸送帶transmissionrack輸送架top stop上死點bottom stop下死點one stroke一行程inch寸動to continue,cont.連動togrip(material)吸料location lump,locating piece,block stop 定位塊reset復位smoothly順利dent壓痕scratch刮傷deformation變形filings鐵削to draw holes抽孔inquiry,search for查尋to stock,storage, instock庫存receive領取approvalexamine andverify審核processing, toprocess加工delivery, to deliver 交貨to return delivenry to. to send delinery back to retrn of goods退貨registration登記registration card登記卡to control管制to put forward and hand in提報safe stock安全庫存acceptance = receive驗收to notice通知applicationform forpurchase請購單consume,consumption消耗to fill in填寫abrasion磨損reverse angle= chamfer倒角character die字模to collect, togather收集failure,trouble故障statistics統計demand andsupply需求career card履歷卡to take aparta die卸下模具to load a die裝上模具to tight a bolt擰緊螺栓to looser abolt擰鬆螺栓to move awaya die plate移走模板easilydamagedparts易損件standardparts標準件breaking.(be)broken,(be)cracked 斷裂to lubricate潤滑common vocabulary for die engineering模具工程常用詞匯die 模具figure file, chart file圖檔cutting die, blanking die 沖裁模progressive die, follow (-on)die連續模compound die 復合模punched hole 沖孔panel board 鑲塊tocutedges=sidecut=side scrap切邊to bending折彎to pull, tostretch拉伸Line streching,line pulling線拉伸engraving, toengrave刻印upsidingdown edges翻邊to stake鉚合designing, todesign設計designmodification設計變化die block模塊folded block折彎塊sliding block滑塊location pin定位銷lifting pin頂料銷die plate,front board模板padding block墊塊stepping bar墊條upper die base上模座lower die base下模座uppersupportingblank上承板upper padding plate blank上墊板spare dies模具備品spring 彈簧bolt螺栓document folder文件夾file folder資料夾to put file in order整理資料spare tools location手工備品倉first count初盤人first check初盤復櫂人second count復盤人second check復盤復核人equipment設備wastematerials廢料work inprogressproduct在制品casing = containerazation裝箱quantity ofphysicalinvetorysecond count復盤點數量quantity ofcustoms count會計師盤,點數量the first page第一聯filed byaccountingdepartmentfor reference會計部存查end-user/usingunit(department)使用單位summary ofyear-endphysicalinventory bills年終盤點截止單據匯總表bill name單據名稱This sheet andphysical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表請與盤點清冊一起送會計部－(NHK 廠區送財會部) Application status records of year-end physical inventory List and physical inventorycard 年終盤點卡與清冊使用－狀況明細表blank andwaste sheetNO.空白與作廢單號plate電鍍mold成型material forengineeringmold testing工程試模材料not includedin physicalinventory不列入盤點sample樣品incomingmaterial to beinspected進貨待驗description品名steel/rolledsteel鋼材materialstatistics sheet物料統計明細表meetingminutes會議記錄meeting type會別distributiondepartment分發單位location地點chairman主席present members出席人員subject主題conclusion結論decision items 決議事項responsible department負責單位pre-fixed finishing date 預定完成日approved by / checked by / prepared by 核準/審核/承辦PCE assembly production schedule sheet PCE組裝廠生產排配表model機鍾work order工令revision版次remark備注productioncontrolconfirmation生產確認checked by初審approved by核準department部門stock ageanalysis sheet庫存貨齡分析表on-handinventory現有庫存availablematerial良品可使用obsoletematerial良品已呆滯to beinspected orreworked待驗或重工total合計causedescription原因說明part number/P/N 料號type形態item/group/class類別quality品質prepared by 制表notes說明year-end physical inventory difference analysis sheet 年終盤點差異分析表physical inventory盤點數量physical count quantity帳面數量difference quantity差異量cause analysis 原因分析raw materials 原料materials物料finishedproduct成品semi-finishedproduct半成品packingmaterials包材goodproduct/accepted goods/acceptedparts/goodparts良品defectiveproduct/non-good parts不良品disposedgoods處理品warehouse/hub倉庫on waylocation在途倉oversealocation海外倉spare partsphysicalinventory list備品盤點清單spare moldslocation模具備品倉skid/pallet棧板tox machine自鉚機wire EDM線割EDM放電機coil stock卷料sheet stock片料tolerance工差score=groove 壓線cam block滑塊pilot導正筒trim剪外邊pierce剪內邊drag form壓鍛差pocket for the punch head挂鉤槽slug hole廢料孔feature die公母模expansion dwg展開圖radius半徑shim(wedge)楔子torch-flamecut火焰切割set screw止付螺絲form block折刀stop pin定位銷round piercepunch=diebutton圓沖子shapepunch=dieinsert異形子stock locaterblock定位塊undercut=scrapchopper清角active plate活動板baffle plate擋塊cover plate蓋板male die公模female die母模groove punch壓線沖子air-cushioneject-rod氣墊頂桿spring-boxeject-plate彈簧箱頂板bushing block襯套insert 入塊club car高爾夫球車capability能力parameter參數factor系數phosphate皮膜化成viscosity涂料粘度alkalidipping 脫脂main manifold主集流脈bezel斜視規blanking穿落模dejecting頂固模demagnetizati on去磁;消磁high-speed transmission 高速傳遞heatdissipation熱傳rack上料degrease脫脂rinse水洗alkaline etch齡咬desmut剝黑膜D.I. rinse純水次Chromate鉻酸處理Anodize陽性處理seal封孔revision版次partnumber/P/N料號good products良品scrapedproducts報放心品defectiveproducts不良品finishedproducts成品disposedproducts處理品barcode條碼flow chart流程表單assembly組裝stamping沖壓molding成型spareparts=buffer備品coordinate座標dismantle the die折模auxiliary fuction輔助功能poly-line多義線heater band 加熱片thermocouple 熱電偶sand blasting 噴沙grit 砂礫derusting machine除銹機degate打澆口dryer烘干機induction感應inductionlight感應光response=reaction=interaction感應ram連杆edge finder巡邊器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 銀紋gas mark焦痕delamination起鱗cold slug冷塊blush 導色gouge溝槽;鑿槽satin texture段面咬花witness line證示線patent專利grit沙礫granule=peuet=grain細粒grit maker抽粒機cushion緩沖magnalium鎂鋁合金magnesium鎂金metal plate鈑金lathe車mill銼plane鉋grind磨drill鋁boring鏜blinster氣泡fillet鑲;嵌邊through-hole form通孔形式voller pin formality滾針形式cam driver鍘楔shank摸柄crank shaft曲柄軸augular offset 角度偏差velocity速度production tempo生產進度現狀torque扭矩spline=themultiple keys花鍵quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten highspeed steel鎢高速的moly highspeed steel鉬高速的organicsolvent有機溶劑bracket小磁導liaison聯絡單volatile揮發性resistance電阻ion離子titrator滴定儀beacon警示燈coolant冷卻液crusher破碎機模具工程類plain die簡易模pierce die沖孔模forming die成型模progressivedie連續模gang dies複合模shearing die 剪邊模riveting die鉚合模pierce沖孔forming成型(抽凸,沖凸) draw hole抽孔bending折彎trim切邊emboss凸點dome凸圓semi-shearing 半剪stamp mark 沖記號deburr or coin 壓毛邊punchriveting沖壓鉚合side stretch側沖壓平reel stretch卷圓壓平groove壓線blanking下料stamp letter沖字(料號)shearing剪斷tick-marknearside正面壓印tick-markfarside反面壓印沖壓名稱類extension dwg展開圖proceduredwg工程圖die structuredwg模具結構圖material材質materialthickness料片厚度factor系數upward向上downward向下pressspecification沖床規格die heightrange適用模高die height閉模高度burr毛邊gap間隙weight重量total wt.總重量punch wt.上模重量五金零件類inner guiding post內導柱inner hexagon screw內六角螺釘dowel pin固定銷coil spring彈簧lifter pin頂料銷eq-height sleeves=spool 等高套筒pin銷lifter guide pin浮升導料銷guide pin導正銷wire spring圓線彈簧outer guidingpost外導柱stop screw止付螺絲located pin定位銷outer bush外導套模板類top plate上托板（頂板）top block上墊腳punch set上模座punch pad上墊板punch holder上夾板stripper pad脫料背板up stripper上脫料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下墊板die holder下夾板die set下模座bottom block 下墊腳bottom plate 下托板(底板) stripping plate內外打(脫料板) outer stripper 外脫料板inner stripper 內脫料板lower stripper 下脫料板零件類punch沖頭insert入塊(嵌入件) deburring punch壓毛邊沖子groove punch 壓線沖子stampedpunch字模沖子round punch圓沖子special shapepunch異形沖子bending block折刀roller滾軸baffle plate擋塊located block定位塊supportingblock forlocation定位支承塊air cushionplate氣墊板air-cushioneject-rod氣墊頂桿trimmingpunch切邊沖子stiffening ribpunch =stinger 加強筋衝子ribbon punch壓筋沖子reel-stretchpunch卷圓壓平沖子guide plate定位板sliding block滑塊sliding dowelblock滑塊固定塊active plate活動板lower sliding plate下滑塊板upper holder block上壓塊upper mid plate上中間板spring box彈簧箱spring-box eject-rod彈簧箱頂桿spring-box eject-plate彈簧箱頂板bushing bolck 襯套cover plate蓋板guide pad導料塊塑件&模具相關英文compre sionmolding壓縮成型flashmold溢流式模具plsitive mold擠壓式模具splitmold分割式模具cavity型控母模core模心公模taper錐拔leather cloak倣皮革shiver飾紋flow mark流痕welding mark溶合痕post screwinsert螺紋套筒埋值self tappingscrew自攻螺絲striper plate脫料板piston活塞cylinder汽缸套chip細碎物handle mold手持式模具移轉成型用模具encapsulationmolding低壓封裝成型射出成型用模具two plate兩極式（模具）well type蓄料井insulated runner絕緣澆道方式hot runner熱澆道runner plat澆道模塊valve gate閥門澆口band heater 環帶狀的電熱器spindle閥針spear head鉋尖頭slag well冷料井cold slag冷料渣air vent排氣道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin頂出針knock pin頂出銷return pin回位銷反頂針sleave套筒stripper plate脫料板insert core放置入子runnerstripper plate澆道脫料板guide pin導銷eject rod (bar)（成型機）頂業捧subzero深冷處理three plate三極式模具runner system澆道系統stress crack應力電裂orientation定向sprue gate射料澆口，直澆口nozzle射嘴sprue lock pin 料頭鉤銷(拉料杆)slag well冷料井side gate側澆口edge gate側緣澆口tab gate搭接澆口film gate薄膜澆口flash gate閘門澆口slit gate縫隙澆口fan gate扇形澆口dish gate因盤形澆口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragmgate隔膜澆口ring gate環形澆口subarine gate潛入式澆口tunnel gate隧道式澆口pin gate針點澆口Φ0.8~1.0mmRunner less無澆道(sprueless)無射料管方式long nozzle延長噴嘴方式sprue澆口;溶渣品質人員名稱類QC qualitycontrol 品質管理人員FQC finalqualitycontrol 終點品質管制人員IPQC inprocessqualitycontrol 制程中的品質管制人員OQC outputqualitycontrol 最終出貨品質管制人員IQCincoming quality control 進料品質管制人員TQC total quality control 全面質量管理POC passage quality control 段檢人員QA quality assurance質量保證人員OQA output quality assurance出貨質量保證人員QE quality engineering品質工程人員品質保證類FAI firstarticleinspection新品首件檢查FAA firstarticleassurance首件確認TVR toolverificationreport 模具確認報告3B 3B 模具正式投產前確認CPcapabilityindex 能力指數CPKcapabilityindex ofprocess 模具製程能力參數SSQAstandardizedsupplierquality 合格供應商品質評估OOBA outof box audit開箱檢查QFD qualityfunctiondeployment品質機能展開FMEAfailure modeleffectivenessanalysis 失效模式分析8 disciplines 8項回復內容FA final audit 最後一次稽核CAR corrective action request 改正行動要求corrective action report 改正行動報告FQC運作類AQL Acceptable Quality Level 運作類允收品質水準S/S Sample size 抽樣檢驗樣本大小ACC Accept允收REE Reject拒收CR Critical極嚴重的MAJ Major主要的MIN Minor輕微的AOQAverageOutputQuality 平均出廠品質AOQLAverageOutputQuality Level平均出廠品質Q/R/SQuality/Reliability/Service品質/可靠度服務MIL-STDMilitary-Standard 軍用標準S I-S IVSpecialI-Special IV特殊抽樣水準等級P/N PartNumber 料號L/N LotNumber 特采AOD AcceptOn Deviation特采UAI Use AsIt 首件檢查報告FPIR First Piece Inspection Report 百萬分之一PPM Percent Per Million 批號制程統計品管專類SPC Statistical Process Control 統計製程管制SQC Statistical Quality Control 統計品質管制R Range全距AR AveraryRange 全距平均值UCL UpperCentral Limit管制上限LCL LowerCentral Limit管制下限MAXMaximum最大值MINMinimum最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重測性判斷量可靠與否DIMDimension尺寸DIADiameter 直徑FREQFrequency頻率N Number樣品數其它品質術語類QCCQualityControl Circle品質圈QIT QualityImprovementTeam 品質改善小組PDCA Plan Do Check Action 計劃執行檢查總結ZD Zero Defect 零缺點QI Quality Improvement 品質改善QP Quality Policy 目標方針TQM Total Quality Management 全面品質管理MRB Material Reject Bill 退貨單LQLLimitingQuality Level最低品質水準RMAReturnMaterialAudit 退料認可QANQualityAmelionrateNotice 品質改善活動ADMAbsoluteDimensionMeasuremat全尺寸測量QT QualityTarget 品質目標7QCTools 7QualityControll Tools品管七大手法通用之件類ECNEngineeringChange Notes工程變更通知(供應商)ECOEngineeringChange Order工程改動要求(客戶)PCNProcessChangeNotice 工序改動通知PMPProduct Management Plan 生產管制計劃SIP Specification In Process 製程檢驗規格SOP Standard Operation Procedure製造作業規範IS Inspection Specification 成品檢驗規範BOM Bill Of Material 物料清單PS Package Specification 包裝規範SPECSpecification規格DWGDrawing 圖面系統文件類QC QualitySystem 品質系統ESEngineeringStandarization 工程標準CGOOChinaGeneralPCE龍華廠文件H Huston(美國)休斯敦C Compaq(美國)康伯公司C China中國大陸A Assembly組裝(廠)S Stamping沖壓(廠)P Painting烤漆(廠)I Intel 英特爾公司T TAIWAN臺灣IWSInternationalWorkmanStandard 工藝標準ISOInternationalStandard Organization 國際標準化組織GS General Specification 一般規格CMCSC-ChinaM-Manufact C-CompaqS-Stamping Compaq產品在龍華衝壓廠製造作業規範CQCAQ-QualityA-Assembly Compaq產品在龍華組裝廠品管作業規範CQCP P-PaintingCompaq產品在龍華烤漆廠品管作業規範部類PMCProduction &MaterialControl 生產和物料控制PPCProductionPlan Control生產計劃控制MCMaterialControl 物料控制MEManafactureEngineering製造工程部PE ProjectEngineering產品工程部A/CAccountantDept 會計部P/APersonal &Administration 人事行政部DCDocumentCenter 資料中心QE QualityEngineering品質工程(部)QA QualityAssurance品質保證(處)QC QualityControl 品質管制(課) PD Product Department 生產部LAB Labratry 實驗室IEIndustrial Engineering 工業工程R&D Research & Design 設計開發部P Painting 烤漆(廠)A Asssembly 組裝(廠)S Stamping 沖壓(廠) 生產類PCS Pieces個(根,塊等)PRS Pairs雙(對等)CTN Carton卡通箱PALPallet/skid棧板POPurchasingOrder 采購訂單MOManufactureOrder 生產單D/C DateCode 生產日期碼ID/CIdentificationCode (供應商)識別碼SWRSpecial WorkRequest 特殊工作需求L/N LotNumber 批號P/N PartNumber 料號其它OEMOriginalEquipmentManufacture原設備製造PCEPersonalComputerEnclosure個人電腦外設PC Personal Computer個人電腦CPUCentral Processing Unit 中央處理器SECCSECC` 電解片SGCC SGCC 熱浸鍍鋅材料NHK North of Hongkong 中國大陸PRCPeople's Republic of China 中國大陸U.S.A theUnited Statesof America美國A.S.A.P AsSoon AsPossible 盡可能快的E-MAILElectrical-Mail 電子郵件N/A NotApplicable不適用QTYQuantity 數量VS 以及REVRevision 版本JIT Just InTime 零庫存I/OInput/Output輸入/輸出OK Ok 好NG NotGood 不行,不合格C=0Critical=0極嚴重不允許ESDElectry-staticDischarge靜電排放5S 希臘語整理,整頓,清掃,清潔,教養ATINAttention 知會CC Carbon Copy 副本復印相關人員APP Approve 核準,認可,承認CHK Check 確認AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只讀光碟FDD FloppyDisk Drive軟碟機HDD HardDisk Drive碟碟機REFReference僅供參考CONNConnector連接器CA V Cavity模穴CADComputer AidDesign 計算機輔助設計ASS'YAssembly 裝配,組裝MAT'SMaterial 材料ICIntegratedCircuit 集成電路T/P TruePosition 真位度TYP Type類型WDRWeeklyDeliveryRequitement周出貨需求C?T CycleTime 制程周期L/T LeadTime 前置時間(生產前準備時間)S/T Standard Time 標準時間P/M Product Market 產品市場3C Computer,Co mmumcation, Consumer electronic's消費性電子5WIH When,Where, Who,What,W hy,How to5M Man,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time 人力,物力,財務,技術,時間(資源)SQAStrategyQualityAssurance策略品質保證DQA DesighQualityAssurance設計品質保證MQAManufactureQualityAssurance製造品質保證SSQA Salesand serviceQualityAssurance銷售及服務品質保證LRR LotRejeet Rate批退率BS Brainstorming 腦力激蕩EMIElectronicMagnetionInspect 高磁測試FMIFrequencyModulatimInspect 高頻測試B/MBoar/Molding (flat cable)C/P Connector of PCA/P Assembly SPS Switching power supply 電源箱DT Desk Top 臥式(機箱)MTMini-Tower立式(機箱) DVD Digital Vedio Disk VCD VdeioCompact DiskLCD LiquidCrystalDisplayCADComputerAID DesignCAMComputerAIDManufacturingCAEComputerAIDEngineeringABIOSAchancedBasic input/outputsystem 先進的基本輸入/輸出系統CMOSComplemeruary MetollOxideSemiconductor 互補金屬氧化物半導體PDAPersonalDigitalAssistant 個人數字助理ICIntegratedCircuit 集成電路ISAIndustryStandardArchitecture工業標準體制結構MCA Micro Channel Architecture 微通道結構EISA Extended Industry Standard Architecture 擴充的工業標準結構SIMM Single in-line memory module 單項導通匯流組件DIMM Dual in-line Memory Module 雙項導通匯流組件LEDLight-Emitting Diode 發光二級管FMEAFailure ModeEffectivenes失效模式分析W/H WireHarness 金屬線緒束集組件F/C FlatCalle 排線PCBPrintedCircuit Board印刷電路板CARCorrectionAction Report改善報告NG NotGood 不良WPRWeeklyDeliveryRequirement周出貨要求PPM PartsPer Million百萬分之一TPM TotalProductionMaintenance全面生產保養MRPMaterialRequiremcntPlanning 物料需計劃OCOperation System 作業系統TBA To Be Design 待定,定缺D/CDrawing ChangeP/P Plans & Procedune EMI Electrical-Mu sic Industry 電子音樂工業RFI Read Frequency Input 讀頻輸入MMC Maximum Material ConditionMMSMaximumMaterial SizeLMC LeastMaterialConditionLMS LeastMaterial Size------------------------------------------------------------------------------------------模具技術用語各種模具常用成形方式accurate diecasting 精密壓鑄powderforming 粉末成形calendaringmolding 壓延成形powdermetal forging粉末鍛造cold chamberdie casting 冷式壓鑄precisionforging 精密鍛造cold forging冷鍛pressforging 沖鍛compactingmolding 粉末壓出成形rocking dieforging 搖動鍛造compoundmolding 複合成形rotary forging 迴轉鍛造compression molding 壓縮成形rotational molding 離心成形dip mold 浸漬成形rubber molding 橡膠成形encapsulation molding 注入成形sand mold casting 砂模鑄造extrusion molding 擠出成形shell casting 殼模鑄造foam forming发泡成形sinter forging燒結鍛造forging roll軋鍛six sidesforging 六面鍛造gravitycasting 重力鑄造slushmolding 凝塑成形hollow(blow)molding 中空(吹出)成形squeezecasting 高壓鑄造hot chamberdie casting 熱室壓鑄swaging 擠鍛hot forging熱鍛transfermolding 轉送成形injectionmolding 射出成形warmforging 溫鍛investmentcasting 精密鑄造matcheddie method對模成形法laminatingmethod 被覆淋膜成形lowpressurecasting 低壓鑄造lost wax casting 脫蠟鑄造matched mould thermal forming 對模熱成形模各式模具分類用語bismuth mold 鉍鑄模landed plunger mold 有肩柱塞式模具burnishing die 擠光模landed positive mold 有肩全壓式模具button die 鑲入式圓形凹模loading shoemold 料套式模具center-gatedmold 中心澆口式模具loose detailmold 活零件模具chill mold 冷硬用鑄模loose mold 活動式模具clod hobbing冷擠壓製模louvering die百葉窗沖切模composite dies複合模具manifold die分歧管模具counter punch反凸模modular mold組合式模具double stackmold 雙層模具multi-cavitymold 多模穴模具electroformedmold 電鑄成形模multi-gatemold 複式澆口模具expander die擴徑模offswtbending die雙折冷彎模具extrusion die擠出模palletizing die 疊層模family mold 反套製品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通氣性模具duplicated cavity plate 複板模positive mold 全壓式模具fantail die 扇尾形模具pressure die 壓緊模fishtail die 魚尾形模具profile die 輪廓模flash mold 溢料式模具progressivedie 順序模gypsum mold石膏鑄模protable mold手提式模具hot-runnermold 熱流道模具prototypemold 雛形試驗模具ingot mold 鋼錠模punching die落料模lancing die 切口模raising(embossing) 壓花起伏成形re-entrantmold 倒角式模具sectional die拼合模runlessinjection mold無流道冷料模具sectionaldie 對合模具segment mold組合模semi-positivemold 半全壓式模具shaper 定型模套singlecavity mold。