sam-ba install
ARM仿真器-更新固件及常见问题-V1.04

ARM仿真器-更新固件及常见问题V1.04目录1.JTAG 模式及典型连接2.SWD 模式及典型连接3.关于2脚(NC)3.3V电源输出说明4.关于19脚5V Supply 供电说明5.如何判断丢失固件6.如何判断新老版本仿真器7.新版本仿真器丢失固件解决方法(擦除固件方法)8.老版本仿真器丢失固件解决方法(擦除固件方法)9.SAM-PROG v2.4软件下载固件方法(WINXP或WIN7 32位)10.sam-ba_2.14.exe软件下载固件方法(WIN7/WIN8)11.WIN7、WIN8安装驱动程序12.仿真器转接板原理图注意:必须操作第7(或8)项擦出固件才能用第9或10项软件下载固件1.JTAG 模式及典型连接2.SWD 模式及典型连接3.关于2脚(NC)3.3V电源输出说明默认不输出3.3V电源;但为了方便用户应用,如果用户一定要输出3.3V电源,请将仿真器壳子打开,把J3的跳线冒放到3.3V一端;注意:强烈建议用户不要这样用,因为这样会造成仿真器及目标板不稳定现象;这个3.3V输出电流不要超过300mA;4.关于19脚5V Supply 供电说明此端口输出5V最大300mA 的电流,如果目标板功耗较大时将无法为目标板供电,因为输出的是5V ,所以务必接入目标板电源芯片的输入端,千万不要接入CPU 的供电脚,可能会损坏芯片。
低版本驱动中没有此选项,可通过J‐Link Commander DOS 窗口中输入power on 回车,手动给目标板供电。
V4.88及以上驱动中需在Options ‐>Project Interface‐>Production 界面中Enable target power 处打勾开启此功能。
如图:5.如何判断丢失固件绿灯不亮了、红灯3秒闪烁一次以及电脑不识别设备都是丢失固件的现象;丢失固件偶尔出现,只要能方便重新烧写就可以,对于工程师来讲这个不是问题;6.如何判断新老版本仿真器:老版本:打开仿真器,左上角版本是:V1.00, 此版本只能打开仿真器按6项说明烧写固件,比较麻烦;新版本:仿真器底部贴有“QC”标志、打开仿真器左上角版本是:V1.02及以上;支持不打开仿真器烧写固件;按5项说明烧写固件;7.新版本仿真器丢失固件解决方法(擦除固件方法)用户再也不用打开仿真器盖子,用复杂的方法更新固件了。
ATMEL SAM-BA and SAM-PROG 说明书

ATMEL SAM-BA™ and SAM-PROG用户手册译者:版本:VER1.1日期:2006-01SAM-BA™ and SAM-PROG: Atmel's Flasher Tools术语:——SAM-BA GUI(SAM-BA图形用户界面)和SAM-PROG为PC端应用程序——SAM-BA BOOT为固化于微控制器端的应用程序SAM-BA™ BootATMEL的应用程序(SAM-BA GUI和SAM-PRO)均使用了嵌入在ROM 中的SAM-BA Boot固件。
SAM-BA Boot固件对芯片进行如下初始化:——启动PLL输出,为USB外设提供一个48MHz的工作频率,——连接USB外设,——连接USART外设,——等待一个来自于USB或者COM的主机连接(PC)。
SAM-BA的主要特性如下:——通过RS232或者USB接口提供ISP操作,——可以通过基于Windows的GUI或者基于DOS的命令行进行操作,——运行于Win2000和WinXP,——可以显示存储器和外设的内容,——目标器件存储器(FLASH)操作:读、写、擦除、配置、校验等——允许使用用户脚本SAM - Boot Assistant (SAM-BA™)——第一点:本快速入门适用于以下器件:——AT91SAM7S32和AT91SAM7S64适用于REV E及以上版本(产品ID:58814E)——AT91SAM7S321适用于REV A及以上版本(产品ID:58837A)——AT91SAM7S128和AT91SAM7S256适用于REV B及以上版本(产品ID:58818B)——第二点:——AT91SAM7S-EK(或者用户自己的基于AT91SAM7S的应用)必须遵从包含两个步骤的“系统恢复程序(System Recovery Procedure)”启动时序。
此步骤将在后面介绍。
——第三点:——Win2000或XP操作系统——SAM-BA GUI应用程序——USB或RS232端口信息:以下表格指示了在上电或者手工复位后通过一些引脚配置进入SAM-BA BOOT(ISP)状态:Pin Name Level Level Default State after resetTST 11 Pull-down PA0/PGMEN0 11 Pull-up PA1/PGMEN1 11 Pull-up PA2/PGMEN2 01 Pull-upBoot up Application -> FFPI SAM-BA BootOther pin setting about TST, PA[0,1,2]/PGMEN|0,1,2] are reserved.系统恢复程序(System Recovery Procedure)1,目标板下电,2,重新对目标板上电之前请确保TST,PA0/PGMEN0,PA1/PGMEN1,PA2/PGMEN2信号已经置位(参见上面的表格),由于PA0/PGMEN0,PA1/PGMEN1,PA2/PGMEN2内置上拉电阻,且复位后上拉电阻使能,而TST 复位后为下拉电阻使能,故只要将TST信号上拉即可,对于AT91SAM7S-EK,短接JP5即可,译者注:步骤2假设TST,PA0-2均未接外部上拉或者下拉电阻,如果有接则请自行保证信号的电平符合上表,3,目标板上电,并请等待10秒钟,4,下电,将TST信号悬空,对于AT91SAM7S-EK拔掉JP5短路帽即可,5,上电,此时目标板上的SAM-BA Boot应用程序已经运行于FLASH并等待来自于USB或者DBGU的主连接(PC),注意:当FLASH安全位(SECURITY BIT)置位后,该系统恢复程序(System Recovery Procedure)将不能执行。
ATMEL SAM—BA应用研究

ATMEL SAM—BA应用研究【摘要】本文介绍了ATMEL AT91SAM系列ARM处理器的下载编程工具SAM-BA的运行原理及用户定制化方法。
【关键词】ARM;SAM-BA;AT91 SAM;ISP1.SAM-BA介绍SAM-BA是ATMEL为其MCU/MPU开发者提供的方便易用的下载编程工具,它可以通过芯片的串口、USB、JTAG口对AT91SAM系列处理器的片内及片外的FLASH编程,也可以通过图形化界面查看片上外设状态及RAM/flash内容。
SAM-BA包括两部分:主机计算机端和接口板或目标板端(如图1所示)。
主机端SAM-BA基于一个公共动态链接库sam-ba.dll,用户可以通过图形界面(如图2所示)和TCL shell命令行的方式来执行。
设备端通过AT91SAM芯片的驻留程序实现。
AT91SAM芯片在上电后首先检测是否有有效的用户代码,如果检测到有效用户代码则运行用户程序。
如果没有,则运行驻留程序进入SAM-BA的监视状态,等待与PC端连接。
此时用户可以通过图形界面或命令行方式与芯片通信。
当设备与SAM-BA连接时,主机将调用以编译好的Applet来执行目标板的初始化、编程、读取等操作。
图1 SAM-BA结构示意图在运行SAM-BA之前,需先连接通信线缆,可以是USB、JTAG或串口线。
如果使用命令行连接方式,其格式为:>[Install Directory]/SAM-BA.exe[Communication Interface][Board][Script_File][Communication Interface]:\USBserial\COMxx或(\usb\ARM0)for USB,\jlink\ARM0 for JTAG,COMxx for RS232(xx为计算机串口号)[Board]用户板名称(在TCL描述文件中定义)[Script_File](可选)命令的TCL描述文件如果使用图形界面的连接方式,接口的选择如图2所示:图2 使用图形界面的连接方式接口的选择2.SAM-BA图形界面当SAM-BA运行起来后,PC将弹出如图3界面,界面包含3部分:显示区,下载区,TCL shell区。
微机(Microchip)EV96C70A 55W双输出转换器操作手册说明书

EV96C70A 55W Dual Output Converter from 36V–54V Input EVB IntroductionThis document provides the description and operating procedures for Microchip's dual output 55V/30W and 5V/25W board from 36V–54V input EV96C70A. This board type is used for evaluating the performance of Microchip PoE systems and the Microchip PWM controller LX7309, which is an integral part of Microchip PoE PD controllersPD70201 and PD70211.Microchip’s PD70201 and PD70211 devices are a part of a family of devices that support the IEEE® 802.3af, IEEE 802.3at, and HDBaseT standards PD interface.The PD interface includes the following family of devices.Table 1. Microchip Powered Device Products OfferingsMicrochip’s EV96C70A evaluation board provides designers with the environment needed for evaluating the performance and implementation of PoE PD applications.The board uses two PWM LX7309, which are an integral part of Microchip PD controllers PD70201 and PD70211. This document provides all necessary procedures and instructions to install and operate this board.Figure 1. EV96C70A Block DiagramThe board can be powered through an input connector J6 by a lab supply or by an output of PoE PD front end. See section 1.3. Electrical Characteristics for the input voltage range. The external load is connected to the evaluation board using the J1 (5V/25W) and J7 (55V/30W) output connectors. The following figure shows the location of input and output connectors.D5 is the 55V indication LED and D9 is the 5V indication LED. These LEDs indicate the presence of the corresponding outputs.The following figure shows a top view of the evaluation board.Figure 2. EV96C70A Evaluation BoardTable of Contents Introduction (1)1. Product Overview (4)1.1. Evaluation Board Features (4)1.2. Evaluation Board Connectors (4)1.3. Electrical Characteristics (5)2. Installation (6)2.1. Initial Configuration (6)3. Schematic (7)4. Bill of Materials (9)5. Board Layout (16)6. Ordering Information (20)7. Revision History (21)The Microchip Website (22)Product Change Notification Service (22)Customer Support (22)Microchip Devices Code Protection Feature (22)Legal Notice (22)Trademarks (23)Quality Management System (24)Worldwide Sales and Service (25)1. Product OverviewThis section provides the product overview of the evaluation board.1.1 Evaluation Board Features•Input DC voltage connector and two output voltage connectors.•Onboard “output present” LED indicators.•36 V DC to 54 V DC input voltage range.•Evaluation board working temperature: 0 ℃ to 70 ℃.•RoHS compliant.1.2 Evaluation Board ConnectorsThe following table lists the evaluation board connectors.Table 1-1. Connector Details1.2.1 Input ConnectorThe following table lists pinout of input connector.Table 1-2. J1 Connector•Manufacturer: On Shore Technology.•Manufacturer part number: ED700/2.1.2.2 Output ConnectorsAn external load is connected to the evaluation board using the J1 and J7 output connectors. The following tables list pinouts of the output connector.The manufacturer and manufacturer part number details of the J1 and J7 output connectors are as follows:•Manufacturer: Kaifeng Electronic.•Manufacturer part number: KF350V-02P-14.Table 1-3. J1 ConnectorTable 1-4. J7 Connector1.3 Electrical CharacteristicsThe following table lists the electrical characteristics of the EV96C70A evaluation board.Table 1-5. Electrical CharacteristicsInstallation 2. InstallationThis section provides information about the installation procedure of the EV96C70A evaluation board.Note: Ensure that power source of the board is turned OFF before all peripheral devices are connected.2.1 Initial ConfigurationPerform the following steps for initial configuration:1.Connect load to the board (using J1 and J7).2.Connect a DC supply to input connector J6.3.Turn ON the DC supply.Schematic 3.l4. Bill of MaterialsThe following table lists the bill of materials.Table 4-1. Bill of MaterialsNote: Third-party components can be replaced by approved equivalents. N.C = not installed (optional).5. Board LayoutThis section describes the layout of the evaluation board. This is a four-layer board with 2 Oz copper. The following figures show the silk of the board for tracking devices placements.Figure 5-1. Top SilkFigure 5-4. Bottom CopperOrdering Information 6. Ordering InformationThe following table lists the evaluation board ordering information.Table 6-1. Evaluation Board Ordering InformationRevision History 7. Revision HistoryThe Microchip WebsiteMicrochip provides online support via our website at /. This website is used to make files and information easily available to customers. Some of the content available includes:•Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software•General Technical Support – Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip design partner program member listing•Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representativesProduct Change Notification ServiceMicrochip’s product change notification service helps keep customers current on Microchip products. Subscribers will receive email notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest.To register, go to /pcn and follow the registration instructions.Customer SupportUsers of Microchip products can receive assistance through several channels:•Distributor or Representative•Local Sales Office•Embedded Solutions Engineer (ESE)•Technical SupportCustomers should contact their distributor, representative or ESE for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in this document.Technical support is available through the website at: /supportMicrochip Devices Code Protection FeatureNote the following details of the code protection feature on Microchip products:•Microchip products meet the specifications contained in their particular Microchip Data Sheet.•Microchip believes that its family of products is secure when used in the intended manner, within operating specifications, and under normal conditions.•Microchip values and aggressively protects its intellectual property rights. Attempts to breach the code protection features of Microchip product is strictly prohibited and may violate the Digital Millennium Copyright Act.•Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code protection does not mean that we are guaranteeing the product is “unbreakable”. Code protection is constantly evolving. Microchip is committed to continuously improving the code protection features of our products. Legal NoticeThis publication and the information herein may be used only with Microchip products, including to design, test,and integrate Microchip products with your application. Use of this information in any other manner violates these terms. Information regarding device applications is provided only for your convenience and may be supersededby updates. It is your responsibility to ensure that your application meets with your specifications. Contact yourlocal Microchip sales office for additional support or, obtain additional support at /en-us/support/ design-help/client-support-services.THIS INFORMATION IS PROVIDED BY MICROCHIP "AS IS". MICROCHIP MAKES NO REPRESENTATIONSOR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORYOR OTHERWISE, RELATED TO THE INFORMATION INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, OR WARRANTIES RELATED TO ITS CONDITION, QUALITY, OR PERFORMANCE.IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL LOSS, DAMAGE, COST, OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE INFORMATION OR ITS USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION OR ITS USE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THE INFORMATION.Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated.TrademarksThe Microchip name and logo, the Microchip logo, Adaptec, AnyRate, AVR, AVR logo, AVR Freaks, BesTime, BitCloud, CryptoMemory, CryptoRF, dsPIC, flexPWR, HELDO, IGLOO, JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus, maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo, MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, PolarFire, Prochip Designer, QTouch, SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash, Symmetricom, SyncServer, Tachyon, TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. AgileSwitch, APT, ClockWorks, The Embedded Control Solutions Company, EtherSynch, Flashtec, Hyper Speed Control, HyperLight Load, IntelliMOS, Libero, motorBench, mTouch, Powermite 3, Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, Quiet- Wire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub, TimePictra, TimeProvider, TrueTime, WinPath, and ZL are registered trademarks of Microchip Technology Incorporated in the U.S.A.Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, Augmented Switching, BlueSky, BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM, , Dynamic Average Matching, DAM, ECAN, Espresso T1S, EtherGREEN, GridTime, IdealBridge, In-Circuit Serial Programming, ICSP, INICnet, Intelligent Paralleling, Inter-Chip Connectivity, JitterBlocker, Knob-on-Display, maxCrypto, maxView, memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, NVM Express, NVMe, Omniscient Code Generation, PICDEM, , PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple Blocker, RTAX, RTG4, SAM-ICE, Serial Quad I/O, simpleMAP, SimpliPHY, SmartBuffer, SmartHLS, SMART-I.S., storClad, SQI, SuperSwitcher, SuperSwitcher II, Switchtec, SynchroPHY, Total Endurance, TSHARC, USBCheck, VariSense, VectorBlox, VeriPHY, ViewSpan, WiperLock, XpressConnect, and ZENA are trademarks of Microchip Technology Incorporated in theU.S.A. and other countries.SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.The Adaptec logo, Frequency on Demand, Silicon Storage Technology, Symmcom, and Trusted Time are registered trademarks of Microchip Technology Inc. in other countries.GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries.All other trademarks mentioned herein are property of their respective companies.© 2022, Microchip Technology Incorporated and its subsidiaries. All Rights Reserved.ISBN: 978-1-5224-9978-7Quality Management SystemFor information regarding Microchip’s Quality Management Systems, please visit /quality.Worldwide Sales and Service。
BOSCH Forum 6 系列 60 x 60 cm 烤箱说明书

Serie 6, Forno con vapore daincasso, 60 x 60 cm, AcciaioHRG5785S6Accessori integrati1 x Teglia da forno smaltata, 1 x Griglia combinata, 1 x Leccarda universale smaltataAccessori opzionaliHEZ317000 Teglia per pizza, HEZ327000 Pietra per pane e pizza, HEZ531000 Leccarda bassa 455x375x30 mm (LxPxA), HEZ531010 Leccarda antiaderen 455x375x30mm (LxPxA), HEZ532000 Leccarda profonda 455x375x38 mm (LxPxA), HEZ532010 Leccarda antiaderen 455x400x38mm (LxPxA), HEZ538000 Guide telescopiche clip a 1 livello, HEZ629070 Teglia per grigliare adatta a pirolisi, HEZ634000 Griglia combinata 455x375x31 mm (LxPxA), HEZ638000 Guide telescopiche clip a 1 livello, HEZ660050 Accessory, HEZ664000 Griglia combinata 455x375x59 mm (LxPxA), HEZ915003 Pirofila in vetro con coperchio 5,4 l., HEZG0AS00 Cavo di collegamento 3m • 30 programmi automatici di cottura: cucinare sarà semplicissimo grazie ai programmi con impostazioni già preselezionate.• Controllo digitale LCD bianco: semplice da utilizzare grazieall'accesso diretto alle funzioni addizionali, suggerimenti di temperatura ed indicazioni di temperatura.• Autopulizia pirolitica: pulizia del forno senza sforzo• Porta piatta con sistema SoftMove: SoftOpen e SoftClose, apertura e chiusura ammortizzate• Termosonda PerfectRoast: rileva la temperatura interna della pietanza con una precisione al grado e al secondo.Dati tecniciTipologia costruttiva del prodotto: .....................................Da incasso Sistema di pulizia: ....................................................................Pirolisi Dimensioni del vano per l'installazione (AxLxP): 585-595 x 560-568 x 550 mmDimensioni (AxLxP): ............................................595 x 594 x 548 mm Dimensioni del prodotto imballato (AxLxP): .......670 x 690 x 660 mm Materiale del cruscotto: ...................................................acciaio inox Materiale porta: ..........................................................................vetro Peso netto: ..............................................................................40.0 kg Volume utile: .................................................................................71 l Metodo di cottura: ...........rigenerazione cibi, Scongelamento, Grill a superficie grande, Aria calda delicata, aria calda, Riscaldamento statico, Funzione pizza, Cottura a bassa temperatura, grill ventilato Materiale della cavità: .................................................................Altro Regolazione della temperatura: .........................................elettronica Numero di luci interne: (1)Lunghezza del cavo di alimentazione elettrica: .....................120.0 cm Codice EAN: (4242005165926)Numero di vani - (2010/30/CE): (1)Classe di efficienza energetica: .........................................................A Energy consumption per cycle conventional (2010/30/EC): ........0.99 kWh/cycleEnergy consumption per cycle forced air convection (2010/30/EC):0.81 kWh/cycleIndice di efficienza energetica (2010/30/CE): ..........................95.3 % Potenza: ..................................................................................3600 W Corrente: .....................................................................................16 A Tensione: .............................................................................220-240 V Frequenza: ...........................................................................50; 60 Hz Tipo di spina: ..........................................................................Schuko Accessori inclusi: 1 x Teglia da forno smaltata, 1 x Griglia combinata, 1 x Leccarda universale smaltataSerie 6, Forno con vapore daincasso, 60 x 60 cm, AcciaioHRG5785S6Caratteristiche principali- Forno con 9 funzioni di cottura: MultiCottura HotAir 3D, Riscaldamento superiore e inferiore, Grill ventilato, Grill a superficie grande, Funzione pizza, Cottura a bassa temperatura, Scongelamento, Aria calda delicata, rigenerazione cibi- Funzioni combinabili con gli impulsi di vapore: aria calda 3D, grill ventilato, riscaldamento statico (resistenza inferiore e superiore)- Display digitale LCD bianco- Volume cavità: 71 l- Regolazione della temperatura da 30 °C a 275 °C- Autopulizia pirolitica- Programmi automatici: 30Altre caratteristiche- Temperatura porta max. 30 °C- Riscaldamento rapido- Illuminazione interna alogena, Illuminazione disinseribile- Orologio elettronico con impostazione inizio e fine cottura- Porta a ribalta, Porta con chiusura ammortizzata SoftClose, SoftMove: grazie ad un meccanismo di ammortizzazione intelligente, la porta si apre e si chiude delicatamente e silenziosamente- Termosonda PerfectRoast- HomeConnect readyAccessori- Accessori: 1 leccarda smaltata bassa, 1 griglia combinata, 1 leccarda universale profonda smaltataEtichetta energetica- Assorbimento massimo elettrico: 3.6 kW- Classe di efficienza energetica (acc. EU Nr. 65/2014): A(in una scala di classi di efficienza energetica da A+++ a D)- Consumo energetico per ciclo durante funzionamento convenzionale:0.99 kWh- Consumo energetico per ciclo durante funzionamento ventilato:0.81 kWh- Numero di cavità: 1 Tipo di alimentazione: elettrica Volume della cavità:71 lSerie 6, Forno con vapore da incasso, 60 x 60 cm, Acciaio HRG5785S6。
Samplitude11安装汉化教程图文详解

Samplitude11安装汉化教程图⽂详解Samplitude 11 是由德国著名公司 MAGIX 出品的⾳乐制作软件,具有数字影像、模拟视频录制、编辑以及5.1环绕声制作功能,可针对⽬前主流的⾳频⽂件进⾏任意切割、剪辑⾳频的处理,⼩编这⾥详细的讲解它的安装破解⽅法!samplitude 11 汉化特别版附教程汉化包+升级补丁类型:⾳频处理⼤⼩:253MB语⾔:简体中⽂时间:2015-06-15查看详情安装⽅法:安装:运⾏ Samplitude.11英⽂版⽂件夹内 “Sam11Std_en-US_setup.exe”,安装原版英⽂精简版完成。
注意:安装后Samplitude 11是⽆法启动的,需要按下⾯的⽅法注册。
注册⽅法:1、注册:到安装⽬录下,找到⽂件“Sam.exe”重命名为“777Alexpol.exe”2、将Samplitude.11英⽂版⽂件夹中⼦⽂件夹Crack内注册程序⽂件“Sam.exe”复制粘贴到安装⽬录下,3、并双击其运⾏注册,注册⽅法见注册⽅法图⽚,注册完成,关闭程序。
4、回到安装⽬录下,删除注册程序⽂件“Sam.exe”,并重新命名⽂件“777Alexpol.exe”为“Sam.exe”6、运⾏MAGIX Samplitude 11.03 升级补丁⽂件夹内升级补丁⽂件“Update Sam 11.0.3.exe”完成后重新启动机器。
7、再次运⾏⼀次 Samplitude 11 然后退出程序进⾏汉化。
8、解压Samplitude 11汉化包并复制所内容覆盖相应Samplitude 11安装⽂件夹下!9、⾄此安装完成,享受它吧!以上就是⼩编为⼤家带来的Samplitude 11安装汉化步骤了,希望可以帮助到⼤家,⼤家如果还有疑问的话,可以在下⽅的评论框内给我们留⾔哦。
我们会尽⾃⼰所能的为⼤家解答。
谢谢⼤家⼀如既往的⽀持,也请⼤家继续关注的后续教程和软件。
IAR SAM8 V3.10中文使用指南

IAR Embedded Workbench用户指南(翻译:老韦)版权声明版权所有1996–2006 IAR系统。
保留所有权利。
没有这个文件的一部分可能没有IAR事先书面同意转载系统。
本文档中描述的软件是提供一个许可下,只能使用或与这样的许可条款规定的复制。
免责声明本文档中的信息如有变更,恕不另行通知,不代表在IAR系统的任何部分的承诺。
而所包含的信息这里被认为是准确的,IAR系统的任何错误不承担任何责任或遗漏。
在任何情况下都不得IAR系统,其雇员,承包商,或该作者文档将承担特别的,直接的,间接的,直接或间接损害,损失,费用,费用,索赔,要求,主张对利润损失,费用,或任何种类或性质的费用。
商标IAR系统,从理念到目标,IAR Embedded Workbench,IAR编程能力makeapp和C-SPY通过IAR 系统拥有的商标的微软和Windows是微软公司的注册商标。
Adobe和Acrobat Reader是注册商标的Adobe系统incorporated.codewright是一个注册商标的母星公司。
所有其他产品名称是其各自的商标或注册商标业主。
版预告第六版:六月2006零件号:uew-6内部参考:4.7.0。
内容简介表..............................................................................................................................十九数字......................................................................................................................二十二前言.......................................................................................................................二十九1部分。
Jlink固件升级烧录指南

Jlink固件升级1.1安装固件升级烧录软件1、找到jlink烧录软件文件夹里的Setup_JLinkARM_V486b,按提示完成安装,如有需要,重启电脑,然后将JLINK一头连接到电脑,另一头连接到目标板的JLINK插座。
2、找到jlink烧录软件文件夹里的sam-ba_2.12,双击进行安装。
3、找到jlink烧录软件文件夹里的Install_AT91-ISP_v1.12,双击进行安装。
1.2擦除芯片并进入编程模式1、打开Jlink外壳,内部电路图如下。
A =ERASE B=TST2、【未在背部标有“上电”字样的JLINK操作过程】1、断开JLINKV8与电脑USB的连接2、短接ERASE的两个过孔3、用USB连接电脑与JLINK4、等待10S5、断开电脑与JLINK的USB连接6、断开ERASE的两个过孔。
【在背部标有“上电”字样的JLINK操作过程】1、用USB连接电脑与JLINK2、短接ERASE的两个过孔3、等待10S4、断开ERASE的两个过孔5、断开JLINKV8与电脑USB的连接。
3、将SAM-BA Boot固件复制到FLASH存储器1、断开电脑与JLINK的USB连接2、短接TST处的两个过孔3、使用USB线连接JLINK与PC机4、等待10s5、拔掉USB线,停止给JLINK供电(说明:请确保此过程中,TST处一直处于短接状态)。
6、断开TST的短接。
1.3更新固件1、用USB线连接JLINK和电脑,对JLINK供电,会提示安装USB驱动,安装完成后在在桌面上选择弹出“管理”,找到“设备管理器”,Jlink与PC连接成功的话会看到JLINK的端口,COM口有可能不同。
2、双击sam-ba.exe打开,会出现下面的对话框,COM口可能不一致。
3、单击connect,出现以下界面4、保持设置不变,点击Send File Name:右边的文件夹,在jlink烧录软件文件夹里找到v8.bin,之后再点击Send File;5、等待安装完成,会弹出两个对话框,第一个选择“是”,第二个选择“否”。
Linux下at91sam9x25嵌软开发测试环境搭建文档

硬件环境软件环境1 安装虚拟机1.1虚拟机选择Ubuntu 11.10以上版本(升级比较方便)1.2虚拟机的配置与升级apt-cache search package 搜索包apt-cache show package 获取包的相关信息,如说明、大小、版本等sudo apt-get install package 安装包sudo apt-get install package - - reinstall 重新安装包sudo apt-get -f install 修复安装"-f = ——fix-missing"sudo apt-get remove package 删除包sudo apt-get remove package - - purge 删除包,包括删除配置文件等sudo apt-get update 更新源sudo apt-get upgrade 更新已安装的包sudo apt-get dist-upgrade 升级系统sudo apt-get dselect-upgrade 使用dselect 升级apt-cache depends package 了解使用依赖apt-cache rdepends package 是查看该包被哪些包依赖sudo apt-get build-dep package 安装相关的编译环境apt-get source package 下载该包的源代码sudo apt-get clean && sudo apt-get autoclean 清理无用的包sudo apt-get check 检查是否有损坏的依赖2 Linux下安装交叉编译环境2.1安装步骤1)下载arm-2011.03-42-arm-none-eabi-i686-pc-linux-2)命令行安装# tar xvzf arm-2011.03-42-arm-none-eabi-i686-pc-linux-# cd arm-2011.033 安装arm设备编程工具SAM Boot Assistant(SAM-BA)3.1 Windows下安装1)安装sam-ba_;2)安装USB CDC驱动;图 3.1图 3.2图 3.3图 3.4图 3.5图 3.7打开SAM-BA 2图 3.8图 3.93.2 Linux下安装1)解压sam-ba_;2)安装USB CDC驱动;1/ Login with administrator rights2/ Unload usbserial module if it is already running #rmmod usbserial3/ Load usbserial kernel module#modprobe usbserial vendor=0x03eb product=0x61244/ Verify that the USB connection is established#lsusb -d 03eb:6124Bus 004 Device 006: ID 03eb:6124 Atmel Corp5/ Know which USB connection is established#dmesgkernel: usb 4-2: new full speed USB device using uhci_hcd and address 5kernel: usb 4-2: configuration #1 chosen from 1 choicekernel: usbserial_generic 4-2:1.0: generic converter detectedkernel: usbserial_generic: probe of 4-2:1.0 failed with error -5kernel: usbserial_generic 4-2:1.1: generic converter detectedkernel: usb 4-2: generic converter now attached to ttyUSBx=> you will have to use /dev/ttyUSBx to connect to your boardRunning SAM-BA CDC Serial version :Launch 'sam-ba_cdc_ file, and select your board and the /dev/ttyUSBxdevice where your board in mounted on.- Update the kernel:# apt-get install linux-image-generic linux-headers-generic- On 64 bits version install 32 bits libraries:# apt-get install ia32-libs- Give sam-ba execute permission if needed:$ chmod +x sam-ba- Connect the board- Create a symlink on /dev/ttyACM0# ln -s /dev/ttyACM0 /dev/ttyUSB0- Launch sam-baTested on:Ubuntu 10.04 64 bits (Ubuntu 10.10 32 bits (Ubuntu 10.10 64 bits (Ubuntu 10.10 64 bits (Ubuntu 11.10 64 bits alpha3How to check if your kernel is up to date ?$ dmesgIf you have something like that (not exactly the same) it's ok:[227274.230016] usb 5-1: new full speed USB device using uhci_hcd and address 5[227274.395739] cdc_acm 5-1:1.0: This device cannot do calls on its own. It is not a modem.[227274.395768] cdc_acm 5-1:1.0: ttyACM0: USB ACM deviceIf you don't have this part: 'This device cannot do calls on its own. It is not a modem.',your kernel is probably not up to date or the cdc_acm patch has not been backported.4 示例4.1 下载AT91Bootstrap源码1)得到源码;2)解压# tar xvzf AT91Bootstrap-5series_#cd AT91Bootstrap-5series_1.24.2 配置AT91Bootstrap和选择启动媒介1) 从NAND FLASH启动#make at91sam9xnf_defconfig2)添加环境变量#vi .profilePATH="$PATH:/root/Public/arm-2011.03/bin"export PATH#souce .profile3)配置AT91Bootstrap#make menuconfig4.3 编译AT91Bootstrap#export $CROSS_COMPILE=” arm-none-eabi-”#make clear#make在../AT91Bootstrap-5series_1.2/binaries下产生at91sam9x5ek-nandflashboot- 4.4 使用AT91Bootstrap二进制文件1)从NAND flash启动A T91Bootstrap图 4.1在NAND和SPI无效的前提下,启动SAM-BA,烧AT91Bootstrap到NAND flash,如图4.1所示:(1)在SAM-BA图形用户界面上选择NandFlash媒介选项卡;(2)1)在NAND有效的前提下,在Scripts下拉列表框中选择“Enable NandFlash”;然后点击“Execute”按钮,完成NandFlash的初始化,如图4.2所示;图 4.2.12)清除芯片上原来烧的信息图 4.2.2结果如图 4.5所示。
南华大学实验报告

竭诚为您提供优质文档/双击可除南华大学实验报告篇一:南华大学实验报告模板南华大学计算机科学与技术学院实验报告(20XX~20XX学年度第一学期)课程名称嵌入式系统原理与设计文件系统构建实验名称姓名李谟军学号20XX9350103专业软件工程班级01班地点8-212教师陈灵娜一.实验目的理解根文件系统在linux系统中的作用,了解根文件的制作过程,进一步的掌握烧写开发板的流程。
二.实验环境AT91sAm9g45-eKes开发板三.实验任务1.学会mkfs.jffs2的使用方法。
2.制作根文件系统JFFs2,了解根文件系统目录构成。
3.将根文件系统通过sam-ba工具烧写到AT91sAm9g45-eKes开发板四.实验原理4.Linux内核启动完成以后,内核将寻找一个根文件系统,在AT91sAm9g45-eKes开发板选用的根文件系统是JFFs2。
通过mkfs.jffs2工具在x86平台下制作出可以在嵌入式平台系统上运行的文件系统,并通sam.ba工具烧写到目标板上进行验证。
mkfs.jffs2命令各参数含义如下(具体使用方法可以使用-h参数查看):-r指定内含根文件系统目录。
-o指定文件系统映像的输出文件名称。
-p表示在映像的结尾用0x0补全到block-i存储格式为小端格式。
-n每个擦除的block中不添加cleanmarker。
-c擦除block的大小。
busybox是标准linux工具的一个单个可执行实现。
busybox包含了一些简单的工具,例如cat和echo,还包含了一些更大,更复杂的工具,例如grep,find,mount以及telnet。
有些人将busbox称为linux工具里的瑞士军刀。
简单地说busybox就好像是个大工具箱。
它集成压缩了linux 的许多工具和命令。
五实验步骤和过程记录(1)准备制作JFFs2根文件系统的工具mkfs.jffs2;(2)建立目录(3)编译busybox;(4)复制动态连接库到lib目录中;(5)创建/etc/init.d/rcs/etc/prodile/etc/fastab/etc/inittab文件,并且复制主机中的/etc/passwd/etc/shadow/etc/group文件到相应的目录中;(6)移植bash,将其复制到/bin目录中;(7)执行mkfs.jffs2-r.orootfs.jffs2-n-e0x20000,生成jffs2根文件系统镜像;(8)通过sam-ba工具将文件系统烧写到开发板上,进行验证。
JLINK V8 固件修复指导

JLINK V8 固件修复指导JLINK V8 使用过程中,如果自身固件意外失效,参考本文档,重新恢复固件,就可以了。
至于为什么会丢失固件,我们已经有了一点经验,比如,JLINK V8,您打开jcommander后,提示升级固件,此时选择不升级,在命令行中操作一下jlink(例如,设置power on命令对外供电)。
此时再打开一个mdk的工程,在mdk中也会提示您升级固件,此时选择升级。
那么这个jlink的固件就100%挂掉了,只能恢复。
分析了一下原因,是同一个jlink有多个进程在操作,此时就有可能会冲突了。
1. 安装固件烧录软件(该软件win7不能正常工作)解压Install AT91-ISP v1.13.rar 后,运行Install AT91-ISP v1.13.exe 进行安装。
2. 打开JLINK V8外壳,按下图操作3. 严格按顺序操作,使芯片进入编程状态3.1 用USB线连接JLINK与PC,为JLINK 供电3.2 可靠短接,图中“ERASE”处的两个过孔,保持30秒3.3 断开“ERASE”处的短接3.4 拔掉JLINK与PC间的USB线3.5 可靠短接,图中“TST”处的两个过孔(3.6-3.8操作时,该处一直处于短接状态)3.6 用USB线连接JLINK与PC,为JLINK 供电(不要放开“TST”处短接)3.7 保持30秒(不要放开“TST”处短接)3.8 拔掉JLINK与PC间的USB线(不要放开“TST”处短接)3.9 至此,断开“TST”处的短接按照以上顺序操作后,jlink的主芯片,将可以被编程了。
4.为此时的jlink安装驱动此时把JLINK通过USB线与电脑相连,初次使用时,需要安装驱动,驱动位置如下:C:\Program Files\ATMEL Corporation\AT91-ISP v1.13\sam-ba 2.9\drv如果安装路径不同,注意选择一下5、打开烧录软件6、看图,按顺序操作注意选择所要的烧写的bin文件点击烧写等待烧写完成,箭头中的“1”表示正在进行,完成后,会变成“0”OK,完成了,此时JLINK应该红灯长亮,点击“EXIT”退出此时重新插拔jlink,就能正确找到了,使用中还是要注意,是否有多进程操作jlink的情况,如果您能复现固件丢失情况,请及时联系我们,谢谢。
天鹰科技 Tiny-linux 说明书 (Ver1.02)

Tiny-linux使用说明书(Ver1.02)天鹰科技期待与您的合作支持博客:支持QQ:645076297支持邮箱:********************团购价:400元零售价:450元首先非常感谢您使用Tiny-linux系统,您获得的不仅仅是一套开发板,而是一套高效的linux开发、调试、代码管理的方案,希望我们双方有更深层次的合作。
在使用我们的开发板之前,请阅读下面的注意事项。
●开发板的左下角是电源部分,由于开发板的功率比较大,该部分会有可能发烫,使用者请注意。
●使用者请认真阅读完说明书之后再对开发板进行操作,避免对开发板造成物理损害。
●开发板支持无线和有线网卡两种通信模式。
●开发板提供详细的技术支持,技术支持QQ:645076297,技术支持邮箱:********************开发板由两个部分组成,即核心板与扩展板,主要的功能芯片都在核心板上,核心板为6层板,这样可以有效地减少干扰。
开发板支持的资源如下:● CPU:AT91SAM9260 BGA VERSION B● SDRAM: ISSI IS42S16100G 2片,64M● NAND: NAND01GW3B2AN6● DATAFLASH:ATMEL AT45DB642D● EEPROM: ATMEL 24A512● RTC:EPSON RTC8025● 温度检测:TCN75开发板采用最新的linux2.6.24内核,在官方内核版本上添加相应的芯片驱动,为提高系统的启动速度,开发板一改往常的BOOTSTRAP+UBOOT+LINUX+FILESYS的格式,使用bootstrap直接启动linux内核,可以将linux的启动时间缩短到7秒左右,如果您需要额外的技术支持,可以联系我们,开发板软件资源包括:● Bootstrap,16位总线宽度● UBOOT 1.3.4● LINUX 2.6.24● BUSYBOX 1.13.2● FILE SYSTEM Tiny-System●有线网卡驱动●无线网卡驱动●MTD-Utils工具。
Jlink无法识别及报clone解决方案

Jlink V8无法识别的USB设备及提示Jlink 为clone版本Keil闪退的解决办法注1:本文吸取了网上各种解决方案,总结而成,感谢各位大侠。
欢迎大家继续完善。
注2“由于作者技术所限,几经测试64bit的操作系统始终无法完成硬件识别及刷机过程,建议除非是大侠,否则不要再用64bit的操作系统尝试了,在这个问题上执着,犯不上,浪费时间。
用32bit的电脑来做这件事吧。
2016.09.25现在我们用的Jlink大部分都是山寨版的,有时候不知为什么就不工作了,出现各种各样的问题,让人好不耐烦,甚至失去学习AMR的勇气,主要的问题总结如下两条:1.windows提醒我们插入的是无法识别的USB设备。
这是因为Jlink中的固件丢失了或者坏掉了(盗版产品的通病),这个时候我们只能把它擦除重新写入固件, Jlink才可以正常的工作。
2.使用Keil MDK 高版本时在配置仿真工具时,由于Keil集成的ARM驱动版本过高(高版本的ARM驱动里现在集成了clone验证)提示Jlink为clone品,Keil开发环境闪退。
以上两者的解决方案目前来看只能是擦除Jlink固件,重新烧写高人的翻墙固件才能解决,是否能彻底解决,有待时间检验。
具体解决过程如下:1固件刷机工具准备可以选择安装如下二者之一:◆安装Install AT91-ISP v1.13.exe 软件(可支持的系统WIN XP WIN7 32bit)win7 64bit找不到驱动,双击Install AT91-ISP v1.13.exe 运行,选择默认设置,安装好以后,桌面上生成如下两个图标:◆安装sam-ba_2.14.exe,安装成功后,桌面会出现如下图标:(建议方案)2Jlink固件擦除操作1、先短接图中ERASE 处的两个过孔。
再使用USB 线连接JLINK 与PC机,以提供JLINK 工作电源。
(如果此时灯没有灭,则来回插拔USB口,直至灯灭),灯灭之后,再等大约5 秒后断开ERASE 位置的两个过孔的短接。
sam10安装方法

1、在安装程序里面找到这个图标的应用程序:
双击安装,
下面会出现一些选项,要照着我的选择的进行哦
点next
打上沟,点next
选择安装地址,next
选择第三项
一个也别打沟,next
接着next就开始安装了。
安装的过程中,会出现几个提示框而暂停安装,不用管它,确定继续安装。
装好程序,就剩下破解了,方法是:
找你安装的sam的程序文件夹,C:\Program Files\MAGIX\Samplitude_10
然后在我发的你的sam安装文件包里找到文件名是crack的文件夹,
把这个文件夹里的如下图图标的EXE 后缀文件拷到C:\Program Files\MAGIX\Samplitude_10的文件夹里,
拷过来后,双击这个文件打开SAM软件,这时会提示你注册,如图:
点击:Register now,注册
在图中输入数字的地方随便输这样的数字,点击箭头指的键然后弹出下面的对话框就破解完成,SAM10可以用了哦。
SAMS 软件使用手册

AT91SAM7S64程序下载软件—BA使用说明

1、 看了上述文档,还有问题如何办?
答:请查阅 BA 软件自带的 Help 文档,该文本较详细地介绍了软件的功能
及使用。您还可以上 网站的“DIY 讨论区”板块发贴请求
大家的援助。
7
学习电子技术就从 DIY 开始 活动主页:/diy - -
22.3 Device Initialization with USB(在Boot Recovery状态下,复位后执行的相关操作)
Initialization follows the steps described below: 1. FIQ initialization 1. Stack setup for ARM supervisor mode 2. Setup the Embedded Flash Controller 3. External Clock detection 4. Main oscillator frequency detection if no external clock detected 5. Switch Master Clock on Main Oscillator 6. Copy code into SRAM 7. C variable initialization 8. PLL setup: PLL is initialized to generate a 48 MHz clock necessary to use the USB Device 9. Disable of the Watchdog and enable of the user reset 10. Initialization of the USB Device Port 11. Jump to SAM-BA Boot sequence (see ”SAM-BA Boot” on page 136)
ICP DAS I-7188E 系列与 I-7000 模块安装指南说明书

Setup I-7188E seriesHow to install I-7188E series with I-7000 modules using MiniOS7 and VXComm Utility? Step 1: Connection of I-7188E seriesPlease use the following connection diagram to setup the I-7188E series and I-7000 modules.Fig : Connection diagram for I-7188E series with I-7000 module.Power up the I-7188E series module and I-7000 modules before proceeding.Step 2: Installation of MiniOS7 UtilityInstall MiniOS7 Utility. Please click on the following link to download the utility and install it on your PC./documents/zips/miniOS7.zipInstall the latest version of MiniOS7 in this case “minios7_utility_v321”Double click on the MiniOS7 Utility Icon on the desktop to open the Utility.Step 3 : Search the I-7188E series module in MiniOS7 UtilityThe following picture shows the main screen of the MiniOS 7 Utlity.Click on the drop down menu on the “connection” and click “Search”The search function should automatically find the I-7188E series.In case the I-7188E series is not found automatically then put the module in “Init” mode. Steps to switch module into “Init” mode:•Jumper a wire across INIT* and GND terminal.•Power cycle the module.The search function would bring up the module as below.Steps to switch module back to normal mode:•Remove the jumper wire from Init* terminal•Power cycle the moduleStep 4: Change IP Address, Subnet Mask and Gateway:Click on the “IP Setting” and change the parameters like IP Address, Subnet Mask and Gateway. (Please check with your companies IT support before changing the IP Address)Step 5: Connect to the I-7188E series moduleAfter the IP Address, Subnet Mask and Gateway is set correctly. Perform the Search function again. Press “Connect”.The connection is verified by checking the serial cable on the next screen.If the serial cable on top right is fluorescent then the module is connected.Step 6: Install the VXComm UtilityPlease click the following link to download the VXComm Utility and the Users Manual. /vxcomm.phpFor Win 98: /pub/cd/8000cd/napdos/driver/vxcomm_driver/9x/For Win 2K/XP: /pub/cd/8000cd/napdos/driver/vxcomm_driver/2k/ Manual: /pub/cd/8000cd/napdos/driver/vxcomm_driver/manual/ Step 7: Launch the VXComm UtilityAfter installing the VXComm Utility, run the Utility using the following path from Windows.The main page of the VXComm Utility is as follows:Use the VXComm Utility Manual to add I-7188E series as the VXComm Server. The following screen should be obtained once you configure I-7188E series module in VXComm. (I-7065 is connected on COM 2 of I-7188E3) Virtual COM 8 in this example.Step 8: Testing the devices connected on COM ports of I-7188E seriesThis is the verification step to confirm that I-7188E series has been configured and setup correctly. This can be done by pulling up the devices connected to the COM ports of I-7188E series in their respective Utilities.Eg: In our example we have I-7065 connected to COM 2 of I-7188E3 (Virtual COM8) Hence we would use DCON Utility to pull up the I-7065 module information.Select the COM 8 in DCON UtilitySearch for the connected device (I-7065). Following is the screen that comes up.。
MPLAB Code Configurator SMPS Library说明书

MPLAB® Code Configurator SMPS Library Release NotesWhat is the MPLAB Code Configurator SMPS LibraryThe MPLAB Code Configurator SMPS Library allows quick and easy configuration, and code generation for 8-bit PIC SMPS applications.System Requirements1.MPLAB® X IDE v5.40 or later2.MCC v4.0.1 or later3.MCC Core v5.0.0 or later4.MCC PIC10 / PIC12 / PIC16 / PIC18 MCU Library 1.81.6 or later5.XC8 compiler v2.20 or laterRelated Hardware and Documentation SupportMPLAB Code Configurator Switch Mode Power Supply Library User's GuideCIP Hybrid Power Starter KitInstalling the MPLAB Code Configurator SMPS Library1.To install the MPLAB® Code Configurator Plugin:1.1.In the MPLAB X IDE, select Plugins from the Tools menu1.2.Select the Available Plugins tab1.3.Check the box for the MPLAB® Code Configurator v4, and click on Install2.To install the SMPS Library:2.1.In the MPLAB X IDE, select Options from the Tools menu2.2.Select the MPLAB® Code Configurator 4.x tab from Plugins option2.3.Click on Install Library/Open Library Folder2.4.Add SMPSPowerLibrary_vX.X.X.jar2.5.Restart MPLAB X IDE (optional)3.To load different SMPS Library version:3.1.Open MPLAB® Code Configurator v4 from the Tools menu3.2.Expand the Versions tab under Software/SMPS Power Library (loaded version is indicated by thegreen mark)3.3.Right click on the desired version of the library and select Mark for load3.4.Click on the Load Selected Libraries button to load the libraryWhat’s New•v1.4.0–Compatibility update with MCC Plugin v4.0.1 and MCC Core v5.0.0–Various output pin fixes•v1.3.0–Added CIP Hybrid Starter Kit (PCMC/VMC) Demo modules–Added a CIP SEPIC LED Driver Demo module•v1.2.1–Removed local peripheral modules–Added dependency to the MCC 8bit PIC Library•v1.2.0–Added support for PIC16(L)F176x devices–Updated the Compensator Block module with an override setting–Updated the Fault Block module with CIN- pin options–Updated the PCMC Control Mode module with LED dimming options –Added the Pulse Modulator Block module–Added the SEPIC_LED Topology module–Added up to four instances of each SMPS Library module•v1.0.0–Initial release with support for a Synchronous Buck Topology moduleSupported Families•8-bit Families–PIC16(L)F177x–PIC16(L)F176xTable of ContentsWhat is the MPLAB Code Configurator SMPS Library (1)1.System Requirements (1)2.Related Hardware and Documentation Support (1)3.Installing the MPLAB Code Configurator SMPS Library (1)4.What’s New (1)5.Supported Families (2)The Microchip Website (4)Product Change Notification Service (4)Customer Support (4)Microchip Devices Code Protection Feature (4)Legal Notice (5)Trademarks (5)Quality Management System (6)Worldwide Sales and Service (7)The Microchip WebsiteMicrochip provides online support via our website at /. This website is used to make files and information easily available to customers. Some of the content available includes:•Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software•General Technical Support – Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip design partner program member listing•Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representativesProduct Change Notification ServiceMicrochip’s product change notification service helps keep customers current on Microchip products. Subscribers will receive email notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest.To register, go to /pcn and follow the registration instructions.Customer SupportUsers of Microchip products can receive assistance through several channels:•Distributor or Representative•Local Sales Office•Embedded Solutions Engineer (ESE)•Technical SupportCustomers should contact their distributor, representative or ESE for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in this document.Technical support is available through the website at: /supportMicrochip Devices Code Protection FeatureNote the following details of the code protection feature on Microchip devices:•Microchip products meet the specifications contained in their particular Microchip Data Sheet.•Microchip believes that its family of products is secure when used in the intended manner and under normal conditions.•There are dishonest and possibly illegal methods being used in attempts to breach the code protection features of the Microchip devices. We believe that these methods require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Attempts to breach these codeprotection features, most likely, cannot be accomplished without violating Microchip’s intellectual property rights.•Microchip is willing to work with any customer who is concerned about the integrity of its code.•Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code protection does not mean that we are guaranteeing the product is “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products.Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act.If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.Legal NoticeInformation contained in this publication is provided for the sole purpose of designing with and using Microchip products. Information regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications.THIS INFORMATION IS PROVIDED BY MICROCHIP “AS IS”. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE OR WARRANTIES RELATED TO ITS CONDITION, QUALITY, OR PERFORMANCE.IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE INFORMATION OR ITS USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION OR ITS USE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THE INFORMATION. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated.TrademarksThe Microchip name and logo, the Microchip logo, Adaptec, AnyRate, AVR, AVR logo, AVR Freaks, BesTime, BitCloud, chipKIT, chipKIT logo, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, HELDO, IGLOO, JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus, maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo, MOST, MOST logo, MPLAB, OptoLyzer, PackeTime, PIC, picoPower, PICSTART, PIC32 logo, PolarFire, Prochip Designer, QTouch, SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash, Symmetricom, SyncServer, Tachyon, TempTrackr, TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.APT, ClockWorks, The Embedded Control Solutions Company, EtherSynch, FlashTec, Hyper Speed Control, HyperLight Load, IntelliMOS, Libero, motorBench, mTouch, Powermite 3, Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, Quiet-Wire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub, TimePictra, TimeProvider, Vite, WinPath, and ZL are registered trademarks of Microchip Technology Incorporated in the U.S.A.Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BlueSky, BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM, , Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, INICnet, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, , PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple Blocker, SAM-ICE, Serial QuadI/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.The Adaptec logo, Frequency on Demand, Silicon Storage Technology, and Symmcom are registered trademarks of Microchip Technology Inc. in other countries.GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries.All other trademarks mentioned herein are property of their respective companies.© 2020, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved.ISBN:Quality Management SystemFor information regarding Microchip’s Quality Management Systems, please visit /quality.Worldwide Sales and Service。
汤森引用号29,40E,编号0489255,指令书:Thompson电视机基本功能及操作指南说明书

MARQUE: THOMSON REFERENCE: 29 DU 40E CODIC: 0489255M a n u e l d’u t i l i s a t i o n B e d i e n u n g s-a n l e i t u n g M a n u a l e d i u t i l i z z a z i o n e M a n u a l d e u t i l i z a c ión F o l h e t o d e u t i l i z ação δηγιες ρησεως25D U40E 28W S43E 29D H40E 29D L40E 29D U40E 32W S43EA propos de cette noticeCe document est commun à plusieurs modèles de téléviseur.réglages peuvent être absents du modèle que vous avez acheté.À propos de l’interrupteurLa position de l’interrupteur Marche/Arrêtle côté droit (voir le dessin à l’intérieur de la couverture de la notice).A propos de la sécuritéObservez avant tout les consignes ci-après, qui ont trait à votre sécurité et à la sûreté de fonctionnement de l’appareil.Les téléviseurs ont besoin d’un refroidissement suffisant pour que leurs composants ne tombent pas en panne par suite de surchauffe.Veillez à ne pas couvrir les ouvertures de la paroi arrière.être suffisamment vastes pour que l’air puisse y circuler.L’appareil est conçu pour être utilisé dans les locaux secs.ner l’appareil à l’extérieur (par ex. sur le balcon, sous la véranda, sous la tente), veillez absolument à le protéger contre l’humidité (rosée, pluie, éclaboussures). Avant de mettre un téléviseur froid en marche dans une pièce chau-de, attendre que la buée qui se trouve sur l’écran se soit évaporée d’elle-même.Température ambiante maximum: 35°A propos de l’entretienLe nettoyage de l’écran s’effectue avec des produits liquides pour vitre.N’utilisez jamais de produits abrasifs.Nettoyez la façade et le coffret à l’aide d’un chiffon doux imprégné d’un détergent neutre. L’utilisation de solvants tels que White Spirit ou un produit à base d’alcool risque d’endommager votre appareil. Nettoyez régulièrement les grilles d’aération à l’arrière de votre téléviseurA propos de la démagnétisationLe champ magnétique terrestre peut agir sur votre téléviseur; cela se traduit par l’apparition de taches de couleur à l’écran. Si cela se produisait:Arrêtez le téléviseur à l’aide de l’interrupteur général.Attendez une heure environ puis remettez en marche.Cette opération permet de démagnétiser automatiquement l’écran. Si les taches de couleur étaient toujours visibles, répétez la procédure.F5Appuyez sur la touche INSTALL du téléviseur si elle est dis-ponible. Dans le cas contraire, mettez le téléviseur en veille puis une longue pression sur la touche menu de la télécom-mande pour affichez le menu qui vous permettra de mettre enservice le téléviseur.Début de l’installationChoisissez la langue que vous préférez pour les menus qui apparaîtront sur l’écran avec les touches Haut/Bas.Validez avec ok.Une liste de pays* vous est proposée (sur 2 pages), sélectionnez celui où vous vous trouvez, ou celui dont vous souhaitez recevoir les chaînes si vous êtes fron-talier.Validez avec ok.Fin de l’installtion* La liste des pays peut varier en fonction des modèles.Mise à jour automatiqueLa mise à jour automatique vous permet d’installer des chaînes récemment mises en service ou de compléter votre installation si certaines chaînes sont absentes ou mal installées.Les chaînes déjà installées ne sont pas effacées.7. Lancez la mise à jour automatique avec okUn message en bas de l’écran vous indique que la mise àjour automatique des chaînes commence.Attendez quelques minutes, lorsque la mise à jour est terminée un autre messa-ge vous l’indique (Fig.3).Programmation automatiqueLa programmation automatique est utile lors d’instal-lations ultérieures à la première installation (ex. suite à un déménagement). Elle efface toutes les chaînes mémorisées antérieurement.Pour l’installation d’une nouvelle chaîne, il est préférable d’uti-Mise à jour automatique ou lamation manuelle(voir paragraphes correspondants).7. Sélectionnez la ligne Programmation auto8. Commencez la Programmation automatique avecProgrammation manuelleL’installation manuelle des chaînes peut être utile si cer-taines chaînes n’ont pas été installées malgré la PRO-GRAMMATION AUTOMATIQUE ou la mise à jour. Appuyez sur la touche INSTALponible.Dans le cas contraire, mettez le téléviseur en veille puis une longue pression sur la touchecommande pour affichez le menuSélectionnez ProgrammationConfiguration A VCe menu vous permet d’identifier les prises et les appareils raccordés. Choisissez un nom d’appareil dans la liste proposée ou composez un autre nom.Appuyez sur la touche INSTALRéglages du sonAffichez le SOMMAIRE avec la touchela télécommande.Sélectionnez la ligne Son.Affichez le menu SON avec okChoisissez et réglez les options proposées en vous aidant des indications ci-dessous.Egaliseur graphiqueCe menu permet de régler la tonalité du son à l’ai-de d’un égaliseur graphique à 5 bandes. Choisissez et réglez les options proposées en vous aidant des indications ci-dessous.Réglage de l’imageAffichez le SOMMAIRE avec la touchela télécommande.Sélectionnez la ligne Image.Affichez le menu IMAGE 1avec Choisissez et réglez les options proposées en vous aidant des indications ci-dessous.Lumière, Couleur, Contraste, Contour :Sélection des chaînesPour les chaîne de 1 à 9, appuyez sur la touche numérique de la télécommande correspondant à la chaî-ne souhaitée. Pour les chaînes supérieures à 10, appuyez sur la touchefiche sur l’écran. Tapez alors à l’aide des touches numériques de la télécommande le chiffre des dizaines puis le chiffre des unités.Si vous appuyez sur 0ment aux chaînes de 1 à 9.Défilement des chaînesVous pouvez faire défiler les chaînes à l’aide des touchesSi vous êtez sur un programme AVdernier programme hertzien regardé.Programmes audiovisuelsUne pression sur la touche av appelle le dernier programme audiovisuel regardé. Des pressions répétées font défiler les programmes audiovisuels.Réglage du volumeAvec les touches volume +/-, augmentez ou diminuez le volume sonore.Coupure du sonUne pression sur la toucheZoomCette fonction est utilie pour des images 4/3 ou letterbox (bandes noires en haut et en bas de l’écran). Avec les touches Gauche/DroiteZOOM 0 : image 4/3 (bandes noires sur les côtés).ZOOM SOUS TITRES*:image agrandie, décalée vers le haut pour pouvoir lire les sous-titres.PLEIN ECRAN* : image 4/3 remplissant l’écran.ZOOM 1 : pour des images en letterbox.* sur modèles 16/9 uniquementAffichage d’informationsUne pression sur la touche info affiche à l’écran les informations suivantes : numéro et nom de la chaîne, heure, zoom, type de son.Préférences Son et ImageUne pression sur la touche rouge affiche le menu des préférences Son et Image.Sélectionnez la ligne souhaitée avec les touchesChoisissez le préréglage qui convient le mieux au programme que vous regardez avec les touches Gauche/Droite.Arrêt du téléviseurPour éteindre le téléviseur, appuyez sur la touche veille de la télécommande ou sur la touche Marche/Arrêt du téléviseur.Liste des chaînesCette fonction vous permet de retourver et d’accéder rapidement aux chaînes en affichant la liste des chaînes. Accès possible également avec la touche list (verte).Le symbole indique que la chaîne a été préalable-ment verrouillée.HeuresVous pouvez programmer dans ce menu l’arrêt ou le réveil automatique de votre téléviseur.Afficher le SOMMAIRE avec la touche commande. Sélectionnez heuresArrêt automatiquepour programmer un arrêt automatique, réglez avecRéveilPour vous faire réveiller par votre télévi-seur, sur la chaîne de votre choix, vous devez préalablement mettre à l’heure l’hor-loge du téléviseur (voir ci-dessus).Affichez le SOMMAIRE avec la touchetélécommande. Sélectionnez heuresSélectionnez Réveil et cochez la case de la fonctionSécurité enfantCette fonction vous permet de désactiver les touchessituées sur le téléviseur. Pour annuler la sécuritéenfant, appuyez sur une des touches numériques dela télécommande.Votre téléviseur passe en sécurité enfant :après un arrêt programmé,si une heure de réveil est programmée,en arrêtant l’appareil en appuyant plus de 3VerrouVous pouvez protéger l’accès à certaines chaînes et au menu INSTALLATION en les verrouillant par un mot de passe.Pour voir une chaîne verrouillée, tapez le mot de passe associé.Affichez le SOMMAIRE avec la touchede la télécommande.Sélectionnez verrou et validez avecTélétexteCertaines chaînes diffusent un journal électronique avec des rubriques varriées et des informations. Vous pouvez l’afficher avec la touche textet les chaînes (Télétexte, Fastext ou Toptext)L’indication “pas de transmission télétexte”signifie que la chaîne ne diffuse pas le télé-texte.Votre téléviseur est capable de mémoriser 500 pages enFastext ou Toptext, pour vous rendre leur consultation plusAppel du NEX TV IEWAccès dirrect par la touche bleueAttention: toutes les chaînes ne diffusent pas “”.A gauche, le navigateur vous permet de faire une recherche dans le guide.A droite, se trouve la liste des émissions.Les touches ok vous permettent de passer de la liste au navigateur.Consulter les programmesactivez le navigateur avec la touchesélectionnez la ligne jour avec les touches activez la zone jour avec la touchechoisissez le jour dont vous voulez connaître les émissions avec les touches ,validez avec la touche ok.Procédez de même pour définir :InfoPour obtenir des renseignements complémentaires sur une émission :activez la liste avec la touchesélectionnez une émission avec les touches appuyez sur la touche jaune infoSi plusieurs pages d’information sont disponibles, la ligne Page apparaît.MémoriserCette fonction n’est active que si l’heure et la date ont été correctement réglés.Pour être prévenu du démarrage d’une émission pendant que vous regardez une autre chaîne, sélectionnez cette émission dans la liste puis sélectionnezSi la liste est pleine, il faut effacer une des programmations précédentes avant de mémoriser ou enregistrer une nouvelle émission (voir “Revue”).En cas de problèmes d’identification de la chaîne, veuillez suivre les instructions affichées automatiquement.RevuePour visualiser les programmes et les enregistrementsmémorisés, sélectionnez la ligne REVUEgateur et validez avec la touche okVous pouvez alors :programmer une mise en marche automatique devotre TV au début de l’émission de votre choix :sélectionnez l’émission dans la liste,F21LECTUREENREGISTREMENT APPELEZ Appareil PriseAppareil Prise PROGRAMMEMagnétoscopeMagnétoscopePéritel ou Péritel AV1AV1CamescopeAV2CamescopeCinches ou MagnétoscopePéritel S-Vidéo ou AV2AV3AV3CamescopeRaccordement d’un camescopefois sur la touche av jusqu’à ce que le program-me AV3 soit sélectionné à l’écran.Lorsque vous arrêterez l’appareil raccordé, le téléviseur restera sur le programme AV3. A l’aide des touches numé-riques de la télécommande, sélectionnez la chaî-ne souhaitée.Raccordement d’un casqueLa prise casque (2)* permet le raccordement d’un casque ou d’écouteurs.Le raccordement d’un casque ne coupe pas le son des haut-parleurs du téléviseur. La touchecoupe le son du TV mais pas le son du casque.Possibilités supplémentairesCopie de cassette :Branchez le magnétoscope enregistreur sur la prise péritélévision AV2.Branchez l’appareil en lecture sur la prose péritélévision AV1 s’il s’agit d’un magnétoscope ou sur les prises CINCH AV3 s’il s’agit d’un camescope (voir tableau ci-dessous).。