FFA60UP60DN中文资料

合集下载

60D操作说明书(最终)

60D操作说明书(最终)

科能技术 1份设计 1份共2份目录第一章工艺简介 (1)第二章起动、运行与停机 (2)第三章运行中的维护和定期试验 (8)第四章事故处理规程 (14)第五章透平发电机事故处理 (14)第六章发电机起停机操作 (19)第七章发电机事故处理 (20)第一章工艺简介高炉配套TRT装置与原高炉减压阀组并联,它由透平主机系统、发配电系统、给排水系统、氮气密封系统、润滑油系统、液压油系统、煤气管道及大型阀门系统、自动控制系统八大系统组成。

高炉产生的煤气经除尘处理后,进入TRT与减压阀组分叉点,当TRT处于停机状态时,高炉煤气经过减压阀组进入低压管网,当TRT正常运行时,高炉煤气经过减压阀组进入低压管网,TRT正常运行时,减压阀组关闭,煤气经TRT入口电动蝶阀或启动调速阀、入口插板阀、快切阀,进入透平机膨胀作功后进入低压煤气管网,供用户使用。

发电机并网选择高炉高压配电系统母线上与电网相连。

当TRT运行时,发电机向电网送电,当高炉短期休风时,发电机可不解列作电动运行。

低压室采用380/220V两路供电。

一路来自TRT站用变压器降压,一路来自高炉低压配电柜低压母线,正常时两路分段运行,当一路进线故障时,联络断路器自动投入。

氮气密封系统的气源来自制氧厂,压力左右,通过自力式压力调节阀、电动单座调节阀等调节环节控制氮气压力,其值应高于煤气压力20kpa,以保证煤气不外泄,从而实现氮封。

在TRT入口插板阀入口上装有吹扫口,用来进行管道吹扫。

润滑油系统采用32号L-TSA汽轮机油(GB 11120-89);液压油系统使用YA-N32液压油。

润滑油供透平机和发电机轴承润滑。

动力油系统控制透平静叶开度、启动调速阀开度、旁通快开阀开度以及向快切阀提供动力油。

自动控制系统用于对TRT机组进行启动、运行检测及自动控制。

图1 TRT系统结构示意图第二章起动、运行与停机第一节透平发电机在下列情况下禁止起动一、调速阀、紧切阀、旁通阀、静叶或保安系统不正常。

Amaran 60d 产品说明书

Amaran 60d 产品说明书

amaran 60d Product Manual EnglishIMPORTANT SAFETY INSTRUCTIONS When using this unit, basic safety precautions should always be followed, including the following:1. Read and understand all instructions before using.2. Close supervision is necessary when any fixture is used by or near children. Do not leave the fixture unattended while in use.3. Care must be taken as burns can occur from touching hot surfaces.4. Do not operate the fixture if a cord is damaged, or if the fixture has been dropped or damaged, until it has been examined by qualified service personnel.5. Position any power cables such that they will not be tripped over, pulled, or put into contact with hot surfaces.6. If an extension cord is necessary, a cord with an amperage rating at least equal to that of the fixture should be used. Cords rated for less amperage than the fixture may overheat.7. Always unplug the lighting fixture from the electrical outlet before cleaning and servicing, or when not in use. Never yank the cord to remove the plug from the outlet.ForewordThank you for purchasing "amaran" series of LED photography lights - amaran 60d.amaran 60d is amaran series of newly designed high cost perfor-mance lamps. Compact structure design, compact and light, excellent texture. Has a high performance level, such as high brightness, high indication, can adjust the brightness,etc. It can be used with the existing Bowens Mount lighting accessories to achieve a variety of lighting effects and enrich product usage patterns. So that the product to meet the needs of different occasions light control, easy to achieve professional level photography.8. Let the lighting fixture cool completely before storing.9. To reduce the risk of electric shock, do not immerse this fixture in water or any other liquids.10. To reduce the risk of fire or electric shock, do not disassemble thisfi******************************************fied service personnel when service or repair work is required. Incorrect reassembly may cause electric shock when the lighting fixture is in use.11. The use of an accessory attachment not recommended by the manufacturer may increase the risk of fire, electric shock, or injury to any persons operating the fixture.12. Power this fixture by connecting it to a grounded outlet.13. Please remove the protective cover before powering on the light.14. Please remove the protection cover before using the reflector.15. Please do not block the ventilation and do not look at the light directly when it is powered on.16. Please do not place the LED lighting fixture nearany liquids or other flammable objects.18. Please have the product checked by an authorized service personnel agent if your product has a problem.19. The malfunctions caused by unauthorized disassembly are not covered under the warranty.20. We recommend only using the original Aputure cableaccessories. Please note that our warranty for this product does not apply to any repairs required due to any malfunctions of unauthorized Aputure accessories, although you may request such repairs for a fee.21. This product is certified by RoHS, CE, KC, PSE, and FCC. Pleas operate the product in full compliance with the operationstandards. Please note that this warranty does not apply torepairs arising from malfunctions, although you may request such repairs on a chargeable basis.22. The instructions and information in this manual are based on thorough, controlled company testing procedures.Further notice will not be given if the design or specifications change.SAVE THESE INSTRUCTIONS FCC Compliance StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may cause undesired operation.Warning:Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment to an outlet on a different circuit than the receiver is connected to. Consult the dealer or an experienced radio/TV technician for help.This device has been evaluated to meet general RF exposure requirements. RF Warning Statement:Check listWhen you unbox the product, please make sure all the items listed below are included.Otherwise, please contact the seller immediately.AC Power Cable (4m) (1 pc)Adapter (1 pc)Bowens Mount Mini Reflector (1 pc)Battery case(1 pc)Tips: The illustrations in the manual are only diagrams for reference. Due to the continuous development of new versions of the product, if there are any differences between the product and the user manual diagrams, please refer to the product itself.Product Details 1. LightAdjusting knob Bowens Mount4. Soft light umbrella installationInsert the soft light handle into the hole and lock the lock knob on the hole.Powered by ACThe power supply* Please press the spring-loaded lock button on the power cord to remove the power cord. Do not pull it out forcibly.to remove the power cord. Do not pull it out forcibly.1. Press the power button to turn the light on and offOperations3. Wireless mode adjustmentA. Rotate the INT adjusting knob to adjust the brightness with 1% variable, and the brightness change range is (0-100) %, and display the change of (0-100) % in real time on the LIGHT body OLED display;B. Click the INT adjustment knob to quickly switch the brightness level: 20%→40%→60%→80%→100%→20%→40%→60%→80%→ 80%→ 40%→60%→80%→100% cycle switch.The user can connect the light body named amaran 60d-xxxxxx through the bluetooth of the mobile phone or tablet (Bluetooth serial number). At this time, the light body can be controlled wirelessly through the mobile phone or tablet.When the light effect is controlled by APP, the word "FX" is displayed in the upper left corner of LCD.In wireless mode, 8 lighting effects can be controlled through App: paparazzi, fireworks, faulty bulb, lightning, TV, pulse, flash, explosion .4. Reset Bluetooth4.1 Long press the Bluetooth Reset button to reset bluetooth.4.2 During the Reset process, the LCD displays BT Reset and the Bluetooth icon is flashing, andthe percentage shows the current Reset progress (1%-50%-100%).4.3 The LCD will display [Success] 2 seconds after the Bluetooth reset is successful.4.4 If the Bluetooth reset is unsuccessful, the LCD will display [Failed] and disappear after 2 seconds.5. OTA modeFirmware updates can be updated online via the Sidus Link App for OTA updates.4.5 After resetting the light's Bluetooth connection, your mobile phone or tablet will be able to connect to and control the light.TLCIAPP Control Type Specifications6. Using the Sidus Link APPYou can download the Sidus Link App from the iOS App Store or Google Play Store for enhancing the functionality of the light. Please visit sidus.link/app/help for more details regarding how to use the app to control your Aputure lights.Power Consumption Cooling Mode Active cooling Light OperatingCurrent 4A 76W 19V100v~240v ,50/60Hz≥96Light OperatingVoltageAdapter Power Supply Remote AbilityBluetooth ≤80mSidus.link/app/helpamaran 60d is compatible with the following light weight accessories :Aputure Light Dome SE ,Light Dome Mini II ,Aputure Lantern .* For more accessory compatibility, please visit the following website:Bowens is a trademark registered by Bowens in China and other countries .The load-bearing capacity of amaran 60d Bowens Mount is limited (maximum load≤ 2.5kg). Do not use heavy-duty modifiers. Please note that our warranty for this product does not apply to any repairs required due to any malfunctions of unauthorized accessories, although you may request such repairs for a fee.Illumination0.5m 13360lux/1241fc149200lux/13860fc1m 3310lux/307fc45100lux/4190fc 3m 5m 379lux/35fc145lux/13fc1664lux/155fc4720lux/438fc CCT5600K* This is an averaged result, the number might be slightly different on each light.DistanceBare BulbHyper-ReflectorPhotometricsModi ers compatibility description:Trademarks。

FFH60UP60S3;FFH60UP60S;中文规格书,Datasheet资料

FFH60UP60S3;FFH60UP60S;中文规格书,Datasheet资料

FFH60UP60S, FFH60UP60S3FFH60UP60S, FFH60UP60S3 Rev. CAbsolute Maximum Ratings 132Backside Metal Connected to CathodeTO247-3L TO247-2LBackside Metal Connected to Cathode13FFH60UP60S, FFH60UP60S3FFH60UP60S, FFH60UP60S3 Rev. C2Electrical Characteristics TC = 25o C unless otherwise notedSymbolParameterMin.Typ.Max.UnitsV FM 1I F = 60AT C = 25°C T C = 125°C-- 1.41.3 1.7-V I RM 1V R =600V T C = 25°CT C = 125°C----100500μA t rr I F = 60A, di/dt = 200A/μs, V CC = 390V T C = 25°C T C = 125°C--6013880-ns W AVLAvalanche Energy ( L = 40mH)50--mJNotes:1:Pulse: Test Pulse width = 300μs, Duty Cycle = 2%Trr test circuit and waveformAvalanch energy test circuit and waveformFFH60UP60S, FFH60UP60S3FFH60UP60S, FFH60UP60S3 Rev. C3FFH60UP60S, FFH60UP60S3FFH60UP60S, FFH60UP60S3 Rev. C4FFH60UP60S, FFH60UP60S3FFH60UP60S, FFH60UP60S3 Rev. C 5Mechanical DimensionsTO247-2LDimensions in MillimetersFFH60UP60S, FFH60UP60S3FFH60UP60S, FFH60UP60S3 Rev. C6TO247-3LFFH60UP60S, FFH60UP60S3FFH60UP60S, FFH60UP60S3 Rev. C*Trademarks of System General Corporation, used under license by Fairchild Semiconductor.DISCLAIMERFAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS.LIFE SUPPORT POLICYFAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.As used here in:Life support devices or systems are devices or systems which, (a) areintended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user.2.A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.PRODUCT STATUS DEFINITIONS Definition of Terms2Cool™AccuPower™Auto-SPM™AX-CAP™*BitSiC ®Build it Now™CorePLUS™CorePOWER™CROSSVOLT ™CTL™Current Transfer Logic™DEUXPEED ®Dual Cool™EcoSPARK ®EfficentMax™ESBC™Fairchild ®Fairchild Semiconductor ®FACT Quiet Series™FACT ®FAST®FastvCore™FETBench™FlashWriter ® *FPS™F-PFS™FRFET®Global Power Resource SM Green FPS™Green FPS™ e-Series™G max ™GTO™IntelliMAX™ISOPLANAR™MegaBuck™MICROCOUPLER™MicroFET™MicroPak™MicroPak2™MillerDrive™MotionMax™Motion-SPM™mWSaver™OptiHiT™OPTOLOGIC ®OPTOPLANAR ®®PDP SPM™Power-SPM™PowerTrench ®PowerXS™Programmable Active Droop™QFET ®QS™Quiet Series™RapidConfigure™ Saving our world, 1mW/W/kW at a time™SignalWise™SmartMax™SMART START™SPM ®STEALTH™SuperFET ®SuperSOT™-3SuperSOT™-6SuperSOT™-8SupreMOS ®SyncFET™Sync-Lock™ ®*The Power Franchise ®The Right Technology for Your Success™®TinyBoost™TinyBuck™TinyCalc™TinyLogic ®TINYOPTO™TinyPower™TinyPWM™TinyWire™TranSiC ®TriFault Detect™TRUECURRENT ®*μSerDes™UHC ®Ultra FRFET™UniFET™VCX™VisualMax™XS™®Datasheet Identification Product Status DefinitionANTI-COUNTERFEITING POLICYFairchild Semiconductor Corporation’s Anti-Counterfeiting Policy. Fairchild’s Anti-Counterfeiting Policy is also stated on our external website, , under Sales Support .Counterfeiting of semiconductor parts is a growing problem in the industry. All manufactures of semiconductor products are experiencing counterfeiting of their parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed application, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who are listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors are genuine parts, have full traceability, meet Fairchild’s quality standards for handing and storage and provide access to Fairchild’s full range of up-to-date technical and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address and warranty issues that may arise. Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors.分销商库存信息:FAIRCHILDFFH60UP60S3FFH60UP60S。

佳能60D详细介绍及摄影技巧(图文篇)

佳能60D详细介绍及摄影技巧(图文篇)

学无止境,60D论坛摄影课堂(第一课)〔更新图!〕朋友们,这些天,来60D论坛的摄友越来越多。

但是,很多朋友还是摄影新手,对摄影的很多知识还不了解。

60D本身是一个比较专业的机器,怎样用好它,是一件很大的课题。

为了帮助大家理解和学习摄影知识,我收集了一些摄影知识与大家一起学习,好了,开课了!!图终于一个一个都插上去了,觉得有用的朋友不要忘记往上顶,以便后来的朋友也能看到!有问题的也可以提出!文案大全第1节光圈与景深首先我们来谈「光圈」,光圈的是一组制作在镜头里面可以活动的叶片,藉由控制光圈的大小,就可以控制光线在一定时间内,进入相机内光量的多寡。

一般在拍照的过程中,我们通常都是藉由调整「光圈」与「快门」的大小组合,来完成一张相片的曝光。

「快门」我们留到下一节中来研究,在这里请大家有空时背一下下面的光圈数值:f1.4 / f2 / f2.8 / f4 / f5.6 /f8 / f11 / f16 / f22 / f32上面的光圈数值,是我们一般相机镜头上常用的光圈值,其中号码越小的光圈(例如 f1.4)它的进光量会越大,相对的光圈号码越大(例如说f22)的进光量反而小。

所以一般我们在说大光圈时,就是指号数越小的光圈值,这点初学者时常会搞混。

文案大全在每一组邻近光圈值之间,都有「一格」(或称为「一级」)的光量差异。

例如f1.4 与f2 两个光圈差了一格,f5.6 与f8 两组光圈间也是差了一格。

每一格光圈的进光量都是以倍数成长,例如f4 的进光量是f5.6 的一倍,f2.8 又是f4 的一倍,这样倒算回去,f2.8 的进光量就是f5.6 的四倍了。

其实不会算这个没有关系,目前你只要知道光圈每一格之间光量的差距是一倍就可以了,另外就是把上面几个光圈值花点时间记下来。

文案大全接下来我们要来谈谈「景深」,景深所指的是当我们对焦完成之后,在底片上呈现完全清楚(也就是说不会模模糊糊的样子)的距离范围。

景深的大小与镜头焦距的长短、光圈的大小以及摄影的距离有密切的互动关系。

FQPF5N60中文资料

FQPF5N60中文资料

IS
Maximum Continuous Drain-Source Diode Forward Current
--
--
2.8
A
ISM
Maximum Pulsed Drain-Source Diode Forward Current
--
--
11.2
A
VSD
Drain-Source Diode Forward Voltage VGS = 0 V, IS = 2.8 A
Bottom : 5.5 V
100
ID , Drain Current [A]
DS(ON) R [Ω ], Drain-Source On-Resistance
10-1 10-1
※ Notes : 1. 250μ s Pulse Test 2. TC = 25℃
100
101
VDS , Drain-Source Voltage [V]
Features
• 2.8A, 600V, RDS(on) = 2.0Ω @VGS = 10 V • Low gate charge ( typical 16 nC) • Low Crss ( typical 9.0 pF) • Fast switching • 100% avalanche tested • Improved dv/dt capability • TO-220F package isolation = 4.0kV (Note 6)
©2002 Fairchild Semiconductor Corporation
Rev. B, June 2002
元器件交易网
FQPF5N60
Typical Characteristics

FGA60N60UFD中文PDF

FGA60N60UFD中文PDF

@ TC = 25oC @ TC = 100oC
@ TC = 25oC @ TC = 25oC @ TC = 100oC
Storage Temperature Range
Maximum Lead Temp. for soldering Purposes, 1/8” from case for 5 seconds
1
FGA60N60UFD Rev. A

FGA60N60UFD 600V, 60A Field Stop IGBT
Package Marking and Ordering Information
Device Marking
Device
FGA60N60UFD FGA60N60UFDTU
VGE = 0V, IC = 250µA
Collector Cut-Off Current G-E Leakage Current
VCE = VCES, VGE = 0V VGE = VGES, VCE = 0V
On Characteristics
VGE(th)
G-E Threshold Voltage
Min.
Typ. Max. Units
Off Characteristics
BVCES ∆BVCES ∆TJ
ICES
IGES
Collector to Emitter Breakdown Voltage VGE = 0V, IC = 250µA
Temperature Coefficient of Breakdown Voltage
180 TC = 125oC
150
20V
15V
12V
120
10V
Collector Current, IC [A]

APT60D60BG;中文规格书,Datasheet资料

APT60D60BG;中文规格书,Datasheet资料

053-6001 R e v K 5-2011PRODUCT BENEFITS• Low Losses• Low Noise Switching• Cooler Operation • Higher Reliability Systems • Increased System Power DensityPRODUCT FEATURES• Ultrafast Recovery Times • Soft Recovery Characteristics• Popular TO-247 Package orSurface Mount D 3PAK Package• Low Forward Voltage • Low Leakage CurrentPRODUCT APPLICATIONS• Anti-Parallel Diode-Switchmode Power Supply -Inverters• Free Wheeling Diode -Motor Controllers -Converters -Inverters • Snubber Diode • PFC600V 60AAPT60D60B APT60D60S APT60D60BG* APT60D60SG**G Denotes RoHS Compliant, Pb Free Terminal Finish.MAXIMUM RATINGSAll Ratings: T C = 25°C unless otherwise speci fi ed.STATIC ELECTRICAL CHARACTERISTICSSymbolV FI RM C TUNITVoltsμApF MIN TYP MAX1.6 1.81.91.4 25050090Characteristic / Test ConditionsForward VoltageMaximum Reverse Leakage Current Junction Capacitance, V R = 200VI F = 60AI F = 120AI F = 60A, T J = 125°CV R = 600VV R = 600V, T J= 125°C1 - Cathode2 - AnodeBack of Case -CathodeCharacteristic / Test Conditions Maximum D.C. Reverse VoltageMaximum Peak Repetitive Reverse Voltage Maximum Working Peak Reverse VoltageMaximum Average Forward Current (T C = 135°C, Duty Cycle = 0.5)RMS Forward Current (Square wave, 50% duty)Non-Repetitive Forward Surge Current (T J = 45°C, 8.3ms)Operating and StorageTemperature Range Lead Temperature for 10 Sec.Symbol V R V RRM V RWM I F(AV)I F(RMS)I FSM T J ,T STGT LUNITVoltsAmps°C APT60D60B_S(G)60060132600-55 to 175300Microsemi Website - /APT60D60B_S(G)DYNAMIC CHARACTERISTICS053-6001 R e v K 5-2011Microsemi reserves the right to change, without notice, the speci fi cations and information contained herein.Z θJ C , T H E R M A L I M P E D A N C E (°C /W )RECTANGULAR PULSE DURATION (seconds)FIGURE 1. MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs. PULSE DURATIONTHERMAL AND MECHANICAL CHARACTERISTICSCharacteristic / Test Conditions Junction-to-Case Thermal Resistance Junction-to-Ambient Thermal Resistance Package WeightMaximum Mounting TorqueSymbol R θJC R θJA W TTorque MINTYPMAX.34 400.22 5.9101.1UNIT °C/W oz glb•in N•mMIN TYP MAX-40 - 130 -220- 4 - - 170 -920- 10 - -80- 1900 -38UNIT ns nC Amps ns nC Amps ns nC AmpsCharacteristic Reverse Recovery Time Reverse Recovery Time Reverse Recovery ChargeMaximum Reverse Recovery Current Reverse Recovery Time Reverse Recovery ChargeMaximum Reverse Recovery Current Reverse Recovery Time Reverse Recovery ChargeMaximum Reverse Recovery CurrentSymbol t rr t rr Q rr I RRM t rr Q rr I RRM t rr Q rr I RRMTest ConditionsI F = 60A, di F /dt = -200A/μs V R = 400V, T C = 25°C I F = 60A, di F /dt = -200A/μs V R = 400V, T C = 125°C I F = 60A, di F /dt = -1000A/μs V R = 400V, T C = 125°C I F = 1A, di F /dt = -100A/μs, V R = 30V, T J = 25°C /053-6001 R e v K 5-2011APT60D60B_S(G)TYPICAL PERFORMANCE CURVES700600500400300200100C J , J U N C T I O N C A P A C I T A N C E K f ,D Y N A M I C P A R A ME T E R S(p F )(N o r m a l i z e d t o 1000A /μs )I F (A V ) (A )T J , JUNCTION TEMPERATURE (°C)Case Temperature (°C)Figure 6. Dynamic Parameters vs. Junction TemperatureFigure 7. Maximum Average Forward Current vs. CaseTemperatureV R , REVERSE VOLTAGE (V)Figure 8. Junction Capacitance vs. Reverse VoltageV F , ANODE-TO-CATHODE VOLTAGE (V) -di F /dt, CURRENT RATE OF CHANGE(A/μs)Figure 2. Forward Current vs. Forward VoltageFigure 3. Reverse Recovery Time vs. Current Rate of Change-di F /dt, CURRENT RATE OF CHANGE (A/μs) -di F /dt, CURRENT RATE OF CHANGE (A/μs) Figure 4. Reverse Recovery Charge vs. Current Rate of Change Figure 5. Reverse Recovery Current vs. Current Rate of ChangeQ r r , R E V E R S E R E C O V E R Y C H A R G E I F , F O R W A R D C U R R E N T (n C )(A )I R R M , R E V E R S E R E C O V E R Y C U R R E N T t r r , R E V E R S E R E C O V E R Y T I M E (A )(n s )1 10 100 200/APT60D60B_S(G)053-6001 R e v K 5-2011Dimensions in Millimeters (Inches )and Leads are PlatedDimensions in Millimeters and (Inches )e1 SAC: Tin, Silver, Coppere3 100% Sn51234di F /dt - Rate of Diode Current Change Through Zero Crossing.I F - Forward Conduction CurrentI RRM - Maximum Reverse Recovery Current.t rr - Revers e R ecovery Time, measured from zero crossing where Q rr - Area Under the Curve Defined by I RRM and t rr .line through I RRM and 0.25 I RRM passes through zero .30 D.U.T.+18V 0VV rFigure 9. Diode Test CircuitFigure 10. Diode Reverse Recovery and De fi nitionsTO-247 Package OutlineD 3PAK Package Outline/分销商库存信息: MICROSEMIAPT60D60BG。

AD604中文文档

AD604中文文档

第一页模拟设备双倍的,超低噪音,可变的增益放大器。

AD604特点:在最大增益上的超低输入噪音:0.8nV/…两个独立的对数线性通道每通道的绝对增益范围:0 dB 到+48dB(前级放大器增益= +14dB),从+6 dB到+54 dB(前级放大增益= +20dB)增益精度是±1.0dB带宽:40MHZ(-3dB)。

300K欧输入电阻可变增益的缩放比例:20dB/V到40dB/V温度下的稳定增益和提供对单端信号可变单级增益控制能够直接驱动A/D转换器应用:超声和声呐时间增益控制高性能AGC系统信号测量产品描述:AD604是一个在超声应用中基于时间可变的增益控制,具有超低噪声,非常精确,双通道,对数线性的特点的可变增益放大器。

并且他将支持很多需求低噪声、宽带可变增益控制的应用。

为了容易使用,AD604的每一个通道都提供一个300 K欧的输入电阻和单级的增益控制。

用户决定增益范围,增益缩放比例和输出的dc 水平移位来更高的提高应用性能。

AD604的每一个通道都使用一个高性能的提供与输入有关的0.8nV/HZ(根号)噪音电压前置放大器。

AD604的不同输入指数级扩音器结构实现非常精确的对数线性响应。

每一个DSX-AMPs (指数级扩音器)包含一个可变的0 dB到48.36 dB衰减器和一个高速的固定增益放大器。

衰减器是基于一个七阶段的R-1.5R的梯形网络。

衰减器中间抽头点是6.908 dB和48.36 dB 对于梯形网络AD604的每一个独立的通道提供一个增益范围为48dB能够被通过编程优化在前置放大器反馈路径有单一外置的寄存器的前置放大器的应用。

AD604的对数增益响应能够被如下等式描述G (dB) = (GainScaling (dB/V) × VGN(V)) + (Preamp Gain (dB) – 19 dB)。

前置放大器增益在5到10 之间(+14 dB and +20 dB)提供全部的增益范围每个通道是0dB到+48 dB和+6dB 到+54dB。

F20UP60DN中文资料

F20UP60DN中文资料

FFPF20UP60DN Rev. A
3

元器件交易网
FFPF20UP60DN
Mechanical Dimensions
TO-220F
3.30 ±0.10
10.16 ±0.20 (7.00)
ø3.18 ±0.10
2.54 ±0.20 (0.70)
10
100
200 300 400 Reverse Voltage, VR [V]
500
600
Figure 3. Typical Junction Capacitance
125
Reverse Recovery Time, trr [ns]
Typical Capacitance at 0V = 124 pF
®
PDP-SPM™ Power220®
Power247® POWEREDGE® Power-SPM™ PowerTrench® Programmable Active Droop™ QFET® QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ SMART START™ SPM® STEALTH™ SuperFET™ SuperSOT™-3 SuperSOT™-6
Figure 4. Typical Reverse Recovery Time vs. di/dt
160
Capacitances , Cj [pF]
100
120
TC = 100 C
o
75
50
80
25
TC = 25 C
o
0 0.1
1 10 Reverse Voltage, VR [V]
100

UPF16060P资料

UPF16060P资料

UPF16060• Typical EDGE PerformanceAverage Output Power = 25 WEfficiency = 35.5%Power Gain = 14.5 dBACPR1 = – 63.9 dBc (30kHz BW offset ± 400kHz normalizedto total power in a 30kHz BW).ACPR2 = – 70.4 dBc (30kHz BW offset ± 600kHz normalized topower in a 30kHz BW).Maximum RatingsRating SymbolValueUnit Drain to Source Voltage, Gate connected to Source BV DSS 65 VoltsGate to Source Voltage BV GSS+15 / –0.5 VoltsTotal Device Dissipation @ Tcase = 70o C Derate above 70o C P D1000.77WattsW/o CStorage Temperature RangeT STG -65 to+150o COperating Junction Temperature T J 200 o CThermal CharacteristicsCharacteristic SymbolTypicalUnit Thermal Resistance, Junction to Case ΘJC 1.2 o C/WElectrical DC Characteristics (Tc=25° C unless otherwise specified)Rating SymbolMinTypMaxUnitDrain to Source Breakdown Voltage (V GS=0, I D=5mA) BV DSS 65 - -VoltsDrain to Source Leakage current (V DS=26V, V GS=0) I DSS - -2.0mAGate to Source Leakage current (V GS=15V, V DS=0) I GSS - -2.0µAThreshold Voltage (V DS=V GS, I D=20mA) V GS(TH) 2.7 4.0 5.0VoltsGate Quiescent Voltage (V DS=26 V, I D=900mA) V GS(Q) 3.0 4.06.0VoltsDrain to Source On Voltage (V GS=10V, I D=1A) V DS(ON) - -0.15VoltsForward Transconductance (V DS=10V, I D=1A) Gm 1.0 - -SAC Characteristics (Tc=25° C unless otherwise specified)Rating SymbolMinTypMaxUnitInput capacitance *(V DS=13V, V GS=0V, f = 1MHz) C ISS - - 110pFOutput capacitance *(V DS= 13V, V GS=0V, f = 1MHz) C OSS - TBD -pFFeedback capacitance *(V DS=13V, V GS=0V, f = 1MHz) C RSS - - 5.0pF* Reference only.RF and Functional Tests (In Cree Microwave Broadband Fixture, Tc=25° C unless otherwise specified)Rating SymbolMinTypMaxUnit CW. Power Gain, P OUT =60WV DD=26V, I DQ=540mAF = 1626MHz and 1660MHzG P 12 13.5 15 dBCW. Power Gain, P OUT =15WV DD=26V, I DQ=540mAF = 1626MHz and 1660MHzG L 1314.516 dBCW. Drain Current, P OUT =90WV DD=26V, I DQ=540mAF= 1626MHz and 1660MHz I D - -5.4ATwo-Tone Common-Source Amplifier Power GainV DD=26V, I DQ=540mA, P OUT = 60 W PEP F1= 1626MHz and F2= 1660MHz, Tone Spacing = 100kHz G TT 1314.5 - dBTwo-Tone Third Order Intermodulation DistortionV DD=26V, I DQ=540mA, P OUT = 60W PEP F1= 1626MHz and F2= 1660MHz, Tone Spacing = 100kHz IMD3 - -30.5-27.0dBcTwo-Tone Drain EfficiencyV DD=26V, I DQ=540mA, P OUT = 60 W PEPF1= 1626MHz and F2= 1660MHz,Tone Spacing = 100kHzηD2Τ35 39 - % Two Tone Drain CurrentV DD=26V, I DQ=540mA, P OUT = 60 W PEP F1= 1660MHz and F2= 1660.1MHz, I MD3 - 2.953.3 AInput Return LossV DD =26V, I DQ=540mA, P OUT = 60 W PEP F1= 1626MHz and F2= 1660MHz, Tone Spacing = 100kHz IRL - -14-9 dBLoad Mismatch Tolerance *V DD=26V, I DQ= 540 mA, P OUT =60W (CW),F=1660MHz @ all phase anglesVSWR 3:1 - - ΨNote (unless otherwise specified):1. Source and load impedance shall be 50 ohms.2. No degradation in the device performance after test.CAUTION - MOS Devices are susceptible to damage from Electrostatic Discharge (ESD). Appropriate precautions in handling, packaging and testing MOS devices must be observed.Note: Class AB broadband circuit performance.。

CS5460A中文数据手册

CS5460A中文数据手册
CS5460A
单相双向功率/电能 IC
特性
l l l l l l l l l l l l l l l 电能数据线性度:在1000 :1 动态范围内线性度 为 ±0.1% 片内功能:可以测量电能(有功),I *V,IRMS 和 VRMS ,具有电能-脉冲转换功能 可以从串行EEPROM 智能“自引导”,不需要微 控制器 AC 或DC 系统校准 具有机械计度器/步进电机驱动器 符合IEC687/1036 ,JIS 工业标准 功耗<12mW 优化的分流器接口 V对I的相位补偿 单电源地参考信号 片内2.5V 参考电压(最大温漂60ppm/℃) 简单的三线数字串行接口 看门狗定时器 内带电源监视器 电源配置 VA+ = +5 V; VA- = 0V; VD+ = +3.3V~+5 V
概述
CS5460A 是一个包含两个ΔΣ模 - 数转换 器(ADC)、高速电能计算功能和一个串行接 口的高度集成的ΔΣ 模-数转换器。 它可以精确 测量和计算有功电能、 瞬时功率、 IRMS 和VRMS , 用于研制开发单相2 线或3 线电表。CS5460A 可以使用低成本的分流器或互感器测量电流, 使 用分压电阻或电压互感器测量电压。CS5460A 具有与微控制器通讯的双向串口, 芯片的脉冲输 出频率与有功能量成正比。CS5460A 具有方便 的片上AC/DC 系统校准功能。 “自引导”的特点使 CS5460A 能独自工 作, 在系统上电后自动初始化。 在自引导模式中, CS5460A 从一个外部EEPROM 中读取校准数 据和启动指令。使用该模式时,CS5460A 工作 时不需要外加微控制器, 因此当电表用于大批量 住宅电能测量时,可降低电表的成本。 订货信息: CS5460A-BS -40℃~+85℃ 24 引脚 SSOP

神舟60cm电子烤箱商品说明书

神舟60cm电子烤箱商品说明书

Serie | 6, Forno da incasso, 60 cm, Acciaio inoxHBA557BS0Accessori opzionaliHEZ317000 , HEZ327000 Pietra per pane e pizza, HEZ530000 , HEZ531000 Leccarda bassa 455x375x30 mm (LxPxA),HEZ531010 Leccarda antiaderen 455x375x30mm (LxPxA),HEZ532000 Leccarda profonda 455x375x38 mm (LxPxA),HEZ532010 Leccarda antiaderen 455x400x38mm (LxPxA),HEZ538000 Guide telescopiche clip a 1 livello, HEZ538200 Guide telescopiche a 2 livelli, HEZ538S00 Guide telescop. a 2 livelli+1 guida clip, HEZ625071 , HEZ633001 Coperchio per tegame professionale, HEZ633070 , HEZ634000 , HEZ636000 Leccarda in vetro 455x364x30 mm (LxPxA), HEZ638200 , HEZ638300 , HEZ915003 Pirofila in vetro con coperchio 5,4 l.Forno da incasso di moderno ed elegante design con programmi automatici di cottura: per preparare piatti perfetti. Cottura HotAir 3D: risultati perfetti di cottura grazie alla distribuzione omogenea del aria al interno della cavità, che consente di cucinare fino a 3 livelli allo stesso tempo. Programmi automatici di cottura: cucinare sarà semplicissimo grazie ai programmi con impostazioni già preselezionate. Comode manopole a scomparsa push-pull: per una pulizia piùsemplice del panello frontale.EcoClean Direct: un modo semplice, ecologico, sicuro ed economico per auto pulire il forno durante il processo di cottura, senza alcun detergente o agente chimico.Dati tecniciColore/materiale del frontale : Acciaio inox Tipologia costruttiva del prodotto : Da incasso Sistema di pulizia :Autopulizia idrolitica, Catalisi totale, Catalisi totale Dimensioni del vano per l'installazione (AxLxP) (mm) :585-595 x 560-568 x 550 Dimensioni del prodotto (mm) : 595 x 594 x 548 Dimensioni del prodotto imballato (AxLxP) (mm) :675 x 690 x 660 Materiale del cruscotto : acciaio inox Materiale porta : vetro Peso netto (kg) : 33,042 Volume utile (l) : 71 Metodo di cottura : aria calda, ariacalda intensiva, Grill a superficie grande, grill ventilato, Hotair gentle, riscaldamento inferiore, riscaldamento superiore/infer. Materiale della cavità : Other Regolazione della temperatura : Meccanico Numero di luci interne : 1 Certificati di omologazione : CE, VDE Lunghezza del cavo di alimentazione elettrica (cm) : 120 Codice EAN : 4242005028986 Numero di vani - (2010/30/CE) : 1 Classe di efficienza energetica (2010/30/EC) : A Energy consumption per cycle conventional (2010/30/EC) :0,97 Energy consumption per cycle forced air convection (2010/30/ EC) : 0,81 Indice di efficienza energetica (2010/30/CE) : 95,3 Dati nominali collegamento elettrico (W) : 3400 Corrente (A) : 16 Tensione (V) : 220-240 Frequenza (Hz) : 60; 50 Tipo di spina : Schuko'!2E20A F-a c i j i g!1/3Serie | 6, Forno da incasso, 60 cm, AcciaioDimensioniinoxHBA557BS0Forno da incasso di moderno ed elegantedesign con programmi automatici di cottura:per preparare piatti perfetti.-Pannelli catalitici Eco Clean: soffitto, parete posteriore, paretilaterale-Programma di pulizia EcoClean-Display digitale LCD a colore bianco-Comode manopole a scomparsa push-pull-Forno elettrico da incasso con 7 funzioni cottura: MultiCotturaHotAir 3D, Riscaldamento superiore e inferiore, Grill ventilato,Grill a superficie grande, Funzione pizza, Riscaldamentoinferiore, Aria calda delicata-Funzione Sprint di riscaldamento rapido-Programmi automatici: 10-Orologio elettronico con impostazione inizio e fine cottura-Regolazione precisa della temperatura da 50-275° C-Raggiungimento temperatura-Illuminazione interna alogena-Volume cavità: 71 l-Classe di efficienza energetica A-Interno porta in vetro-Porta coolGlass: Temperatura porta max. 40°C-<8088brandlookup_nl(TUE, KIN, SIK, SIB, REW, STA, TKS)>-Raffreddamento tangenziale-Accessori in dotazione: 1 leccarda universale profondasmaltata, 1 griglia combinata.-Dimensioni apparecchio (AxLxP): 595 mm x 594 mm x 548mm-Dimensioni nicchia (AxLxP): 560 mm - 568 mm x 585 mm -595 mm x 550 mm-Si prega di fare riferimento alle quote d'installazione mostratenel disegno tecnico-Classe di efficienza energetica (acc. EU Nr. 65/2014): A(in una scala di classi di efficienza energetica da A+++ aD) Consumo energetico per ciclo durante funzionamentoconvenzionale: 0.97 kWh Consumo energetico per ciclodurante funzionamento ventilato: 0.81 kWh Numero di cavità:1 Tipo di alimentazione: elettrica Volume della cavità: 71 lEtichetta energetica-Classe di efficienza energetica (acc. EU Nr. 65/2014): A(in una scala di classi di efficienza energetica da A+++ aD) Consumo energetico per ciclo durante funzionamentoconvenzionale: 0.97 kWh Consumo energetico per ciclodurante funzionamento ventilato: 0.81 kWh Numero di cavità:1 Tipo di alimentazione: elettrica Volume della cavità: 71 l2/3Serie | 6, Forno da incasso, 60 cm, AcciaioinoxHBA557BS03/3。

LPZ系列底部挂载平行驱动包(标准负载)60HZ直驱电机产品说明书

LPZ系列底部挂载平行驱动包(标准负载)60HZ直驱电机产品说明书

851-528 Rev. BInstallation, Maintenance& Parts ManualTable of ContentsWarnings − General Safety 2. . . . . . . . . . . . . . . . . . . . Introduction 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Description 3. . . . . . . . . . . . . . . . . . . . . . . . . . Specifications 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gearmotors 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3200 Belt Speeds 6. . . . . . . . . . . . . . . . . . . . . . . . . . Installation 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Required Tools 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Preventive Maintenance & Adjustment 8. . . . . . . . . . . Required Tools 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . Timing Belt Tensioning 8. . . . . . . . . . . . . . . . . . . . . Timing Belt Replacement 8. . . . . . . . . . . . . . . . . . . Drive or Driven Pulley Replacement 9. . . . . . . . . . . Motor Replacement 9. . . . . . . . . . . . . . . . . . . . . . . . Service Parts 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bottom Mount Drive Package 11. . . . . . . . . . . . . . . Gearmotors 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Return Policy 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IntroductionIMPORTANT: Some illustrations may show guardsremoved. Do NOT operate equipment without guards.Upon receipt of shipment:D Compare shipment with packing slip. Contact factoryregarding discrepancies.D Inspect packages for shipping damage. Contact carrierregarding damage.D Accessories may be shipped loose. See accessory in-structions for installation.Dorner 3200 Series conveyors are covered by patentnumbers 5156260, 5156261, 5203447, 5265714 andpatent applications in other countries.Dorner LPZ Series conveyors are covered by patentnumbers 5156260, 5156261, 5203447, 5265714,5875883 and patent applications in other countries.Dorner’s Limited Warranty applies.Dorner reserves the right to make changes at any timewithout notice or obligation.Dorner has convenient, pre−configured kits of Key ServiceParts for all conveyor products. These time saving kits are easyto order, designed for fast installation, and guarantee you willhave what you need when you need it. Key Parts and Kits aremarked in the Service Parts section of this manual with thePerformance Parts Kits logo .Warnings − General Safety3200 & LPZ Series Bottom Mount Parallel Drive Package for Standard Load 60 Hz Gearmotors IMPM851-528 Rev. B2Dorner Mfg. Corp.3200 & LPZ Series Bottom Mount Parallel Drive Package for Standard Load 60 Hz Gearmotors IMPMDorner Mfg. Corp.3851-528 Rev. BRefer to Figure 1 for typical components.A ConveyorB Mounting BracketC GearmotorD Timing Belt TensionerE CoverF Timing BeltG Drive Pulley HDriven PulleyTypical ComponentsFigure 1AF GCBH DSpecificationsGearmotor Mounting Package Models:Example:S = Standard Load Driven Pulley (see Table 2, 3 & 4)− = flat belt, A through J = cleated belt )Table 1: Gearmotor SpecificationsSingle PhaseThree Phase DCVariable Speed VFDVariable Speed Power/Gear Ratio hp (kW)hp (kW)hp (kW)hp (kW)5:1.08 (.06).17 (.13).12 (.09).17 (.13)10:1.17 (.13).17 (.13).25 (.19).17 (.13)20:1.33 (.25).38 (.28).25 (.19).38 (.28)30:1.33 (.25).38 (.28).25 (.19).38 (.28)60:1.33 (.25).38 (.28).33 (.25).38 (.28)180:1.33 (.25).38 (.28)N/A .38 (.28)Input Voltage 115 VAC 230 VAC 130 VDC 230 VAC Input Frequency60 Hz60 HzN/A10 to 60 HzProduct DescriptionTable 1: Gearmotor Specifications ContinuedSingle Phase Three Phase DCVariable Speed VFD Variable SpeedInput Current/Gear RatioFLA FLA FLA FLA 5:1 1.2 1.0 1.0 1.0 10:1 1.9 1.0 1.8 1.0 20:14 1.9 1.8 1.9 30:14 1.9 1.8 1.9 60:14 1.9 2.3 1.9 180:14 1.9N/A 1.9 Motor RPM1725172525001725Power/Ratio Totally Enclosed Fan Cooled Totally EnclosedNon−Ventilated Totally Enclosed Fan CooledTable 2: Belt Speeds for Fixed Speed Parallel Shaft 60 Hz GearmotorsStandard Load Gearmotors Belt Speed DrivePulley DrivenPart Number RPM In-lb N-m Ft/min M/min Pulley62M180PS4vpFn1022625.57.6 2.3161662M180PS4vpFn1022625.511.4 3.5241662M060PS4vpFn2923726.822.97.0161632M030PS4vpFn5814216.045.814.0161632M020PS4vpFn86788.868.620.9161632M020PS4vpFn86788.8103.031.4241632M010PS4vpFn17341 4.6137.341.9161632M010PS4vpFn17341 4.6171.652.3201632M010PS4vpFn17341 4.6205.962.8241632M005PS4vpFn34541 4.6274.683.7161632M005PS4vpFn34541 4.6343.2104.6201632M005PS4vpFn34541 4.6411.9125.62416(vp) = voltage and phase11 = 115 V, 1-phase23 = 208–230/460 V, 3-phaseTable 3: Belt Speeds for Variable Speed Parallel Shaft VFD Gearmotors Standard Load Gearmotors Belt Speed Drive Driven Part Number RPM In-lb N-m Ft/min M/min Pulley Pulley62M180PS4vpFn1022625.5 1.3−7.60.4−2.3161662M060PS4vpFn2923726.8 3.8−22.9 1.2−7.0161632M030PS4vpFn5814216.07.6−45.8 2.3−14.0161632M020PS4vpFn86788.811.5−68.6 3.5−20.9161632M020PS4vpFn86788.817.2−103.0 5.2−31.4241632M010PS4vpFn17341 4.622.9−137.37.0−41.9161632M010PS4vpFn17341 4.634.4−205.910.5−62.8241632M005PS4vpFn34541 4.645.9−274.614.0−83.71616Specifications3200 & LPZ Series Bottom Mount Parallel Drive Package for Standard Load 60 Hz Gearmotors IMPM851-528 Rev. B4Dorner Mfg. Corp.32M005PS4vpFn34541 4.657.3−343.217.5−104.6201632M005PS4vpFn34541 4.668.8−411.921.0−125.624163200 & LPZ Series Bottom Mount Parallel Drive Package for Standard Load 60 Hz Gearmotors IMPMDorner Mfg. Corp.5851-528 Rev. B3200 & LPZ Series Bottom Mount Parallel Drive Package for Standard Load 60 Hz Gearmotors IMPM851-528 Rev. B 6Dorner Mfg. Corp.Table 4: Belt Speeds for Variable Speed Parallel Shaft DC GearmotorsStandard Load GearmotorsBelt SpeedDrive PulleyDrivenPart Number RPM In-lb N-m Ft/minM/minPulley62M180PSD3DEN 1422625.5 1.3−11.10.4−3.4161662M180PSD3DEN 1422625.5 2.0−16.60.6−5.1241662M060PSD3DEN 4223726.8 4.0−33.2 1.2−10.1161662M030PSD3DEN 8314216.08.0−66.3 2.4−20.2161662M020PSD3DEN 125788.811.9−99.5 3.6−30.3161662M020PSD3DEN 125788.817.9−149.2 5.5−45.5241662M010PSD3DEN 25041 4.623.9−199.07.3−60.7161662M010PSD3DEN 25041 4.629.8−248.79.1−75.8201662M010PSD3DEN250414.635.8−298.510.9−91.02416NOTE: For belt speed other than those listed, contactfactory for details.InstallationRequired ToolsD Hex key wrenches:2 mm, 2.5 mm, 3 mm, 5 mm D Straight edge D Torque wrenchMountingInstallation Component ListE CoverF Timing BeltG Drive PulleyH Driven PulleyI Bottom Mount Drive Assembly J Cover Screws K KeyL M6 Socket Head Screws (4x)M M8 Socket Head Screws (2x)NT ensioner1.Typical components (Figure 2)Figure 2LHEFG K MIJ NNOTE: Cleated belt mounting package shown, flat beltmounting package similar.2.Locate drive output shaft (Q of Figure 3). Removetwo (2) M8 screws (P) and four (4) M6 screws (O)and discard.Figure 3QPOSpecifications3200 & LPZ Series Bottom Mount Parallel Drive Package for Standard Load 60 Hz Gearmotors IMPMDorner Mfg. Corp.7851-528 Rev. B3.Attach bottom mount drive assembly (B of Figure 4)with two (2) M8 screws (M) and four (4) M6 screws (L). Tighten M6 screws (L) to 146 in −lbs (16.5 N −m)and M8 screws (M) to 288 in −lbs (32.5 N −m).Figure 4BML4.Install key (K of Figure 5).Figure 5FG5.Wrap timing belt (F) around driven pulley (H) anddrive pulley (G). Install driven pulley (H) onto conveyor shaft.ing a straight edge (R of Figure 6), align drivenpulley (H) with drive pulley (G). Tighten driven pulley taper-lock screws (S of Figure 7).Figure 6HGFigure 77.Depending on conveyor belt travel (direction 1 or 2),locate timing belt tensioner (N of Figure 8) as shown.Tension timing belt to obtain 1/8” (3 mm) deflectionfor 6 lb (3 Kg) of force at timing belt mid-point (T).Tighten tensioner screw to 110 in-lb (12 Nm).Figure 8T8.Install cover (E of Figure 9) with four (4) screws (J).Tighten screws to 35 in-lb (4 Nm).Figure 9EJJInstallationRequired ToolsD Hex key wrenches:2 mm, 2.5 mm,3 mm, 5 mmD Adjustable wrench (for hexagon head screws)D Straight edgeD Torque wrenchTiming Belt Tensioning1.Remove four (4) screws (J of Figure 9) and removecover (E).2.Loosen tensioner (N of Figure 10).Figure 10N3.Depending on conveyor belt travel (direction 1 or 2),locate timing belt tensioner (N of Figure 8) as shown. Tension timing belt to obtain 1/8” (3 mm) deflection for 6 lb (3 Kg) of force at timing belt mid-point (T). Tighten tensioner screw to 110 in-lb(12 Nm).4.Install cover (E of Figure 9) with four (4) screws (J).Tighten screws to 35 in-lb (4 Nm).Timing Belt Replacement1.Remove four (4) screws (J of Figure 9) and removecover (E).2.Loosen tensioner (N of Figure 10).3.Remove timing belt (F of Figure 11).NOTE: If timing belt does not slide over pulley flange, loosen driven pulley taper-lock screws (S of Figure 7 & 11) and remove pulley with belt (F). For re-installation, see steps 5 and 6 on page 7.Figure 11FS4.Install new timing belt.5.Depending on conveyor belt travel (direction 1 or 2),locate timing belt tensioner (N of Figure 8) as shown. Tension timing belt to obtain 1/8” (3 mm) deflection for 6 lb (3 Kg) of force at timing belt mid-point (T). Tighten tensioner screw to 110 in-lb(12 Nm).6.Install cover (E of Figure 9) with four (4) screws (J).Tighten screws to 35 in-lb (4 Nm).Preventive Maintenance and Adjustment3200 & LPZ Series Bottom Mount Parallel Drive Package for Standard Load 60 Hz Gearmotors IMPM851-528 Rev. B8Dorner Mfg. Corp.3200 & LPZ Series Bottom Mount Parallel Drive Package for Standard Load 60 Hz Gearmotors IMPMDorner Mfg. Corp.9851-528 Rev. BDrive or Driven Pulley Replacementplete steps 1 through 3 of “Timing BeltReplacement” section on page 8.2.Remove taper-lock screws (S of Figure 12). Insert one(1) of taper lock screws (S of Figure 12) in remaining hole (U). Tighten screw (S) until pulley is loose.Remove pulley and taper hub assembly.Figure 12NOTE: If drive pulley (G of Figure 5) is replaced,wrap timing belt around drive pulley and complete step 3.plete steps 5 through 8 of “Installation” sectionbeginning on page 7.Motor Replacement1.For single phase motor, unplug power cord fromoutlet.2.For three phase and VFD variable speed motor:a .Loosen terminal box screws (V of Figure 13) andremove cover (W).Figure 13b .Record incoming wire colors on red, black andblue leads. Loosen wire nuts and remove incoming wires.c .Loosen cord grip and remove cord.Preventive Maintenance and Adjustment3200 & LPZ Series Bottom Mount Parallel Drive Package for Standard Load 60 Hz Gearmotors IMPM851-528 Rev. B 10Dorner Mfg. Corp.3.For DC variable speed motor, unplug motor cord atdisconnect (X of Figure 14).Figure 144.Remove the drive pulley see steps 1 and 2 of “Driveor Driven Pulley Replacement” section on page 9.5.Remove four (4) screws (J of Figure 15). Detach motor (C) from the mounting plate (B). Retain motor output shaft key (K).Figure 15CBKJ6.Install new motor using the four (4) mountingscrews (J of Figure 15).7.Re −install the drive pulley reverse step 2 of “Driveor Driven Pulley Replacement” section on page plete steps 5 through 8 of “Installation” section beginning on page 7.9.Replace wiring:D For a single phase motor, reverse step 1 on this page.D For a three phase or VFD variable speed motor, re-verse step 2 on this page.D For a DC variable speed motor, reverse step 3 on this page.Preventive Maintenance and Adjustment3200 & LPZ Series Bottom Mount Parallel Drive Package for Standard Load 60 Hz Gearmotors IMPMDorner Mfg. Corp.11851-528 Rev. BNOTE: For replacement parts other than thoseshown on this page, contact an authorized Dorner Service Center or the factory. Key Service Parts and Kits are identified by the Performance Parts Kits logo. . Dorner recommends keeping these parts on hand.3200 Series Conveyors Bottom Mount Parallel Drive Package for Standard Load Industrial Gearmotors12341110912131415176851677Item Part Number Description 1300871Drive Cover300349Drive Cover (Flat Belt)2301076Drive Tensioner Slide 3301152Mounting Plate301154Mounting Plate (Flat Belt)4301153Tensioner Bearing Assy5811−123Driven Pulley, 14 Tooth, Taper Lock TL1108811−126Driven Pulley, 16 Tooth, Taper Lock TL11086811−126Drive Pulley, 16 Tooth, Taper Lock TL1108811−127Drive Pulley, 18 Tooth, Taper Lock TL1210811−135Drive Pulley, 20 Tooth, Taper Lock TL1210811−136Drive Pulley, 22 Tooth, Taper Lock TL1610811−137Drive Pulley, 24 Tooth, Taper Lock TL1610Service Parts3200 & LPZ Series Bottom Mount Parallel Drive Package for Standard Load 60 Hz Gearmotors IMPM851-528 Rev. B 12Dorner Mfg. Corp.7811−288Taper Lock Bushing, 20MM, TL1108811−289Taper Lock Bushing, 20MM, TL1210811−290Taper Lock Bushing, 20MM, TL16108814−059Timing Belt, 1.0” W x 27.0” L 814−060Timing Belt, 1.0” W x 28.0” L 9902−130Cap Head Screw 1/4−20 x 0.62”10911−013Flat Washer11920843M Flange Socket Head Screw M4 x 16mm 12920608M Socket Head Screw M6 x 8mm 13920620M Socket Head Screw M6 x 20mm 14920835M Socket Head Screw M8 x 35mm 15961645M Socket Head Screw M16 x 45mm 16980632M Square Key 17991610MHex Jam Nut M16Service Parts3200 & LPZ Series Bottom Mount Parallel Drive Package for Standard Load 60 Hz Gearmotors IMPMDorner Mfg. Corp.13851-528 Rev. B3200 Standard Load Parallel Shaft Industrial GearmotorsFigure 1621ItemPart No.Part Description162M180PS411FN Motor, 0.08hp (0.06Kw), 115 Volts, 60 Hz, 1-Phase62M180PS411FR Motor, 0.08hp (0.06Kw), 115 Volts, 60 Hz, 1-Phase with Reversing 62M180PS423FN Motor, 0.17hp (0.13Kw),208−230/460 Volts, 60 Hz, 3-Phase 62M060PS411FNMotor, 0.17hp (0.13Kw), 115 Volts, 60 Hz, 1-Phase62M060PS411FR Motor, 0.17hp (0.13Kw), 115 Volts, 60 Hz, 1-Phase with Reversing 62M060PS423FNMotor, 0.17hp (0.13Kw),208−230/460 Volts, 60 Hz, 3-Phase 62M030PS411FN Motor, 0.33hp (0.25Kw), 115 Volts, 60 Hz, 1-Phase62M030PS411FR Motor, 0.33hp (0.25Kw), 115 Volts, 60 Hz, 1-Phase with Reversing 62M030PS423FN Motor, 0.38hp (0.28Kw),208−230/460 Volts, 60 Hz, 3-Phase 62M020PS411FN Motor, 0.33hp (0.25Kw), 115 Volts, 60 Hz, 1-Phase62M020PS411FR Motor, 0.33hp (0.25Kw), 115 Volts, 60 Hz, 1-Phase with Reversing 62M020PS423FN Motor, 0.38hp (0.28Kw),208−230/460 Volts, 60 Hz, 3-Phase 62M010PS411FN Motor, 0.33hp (0.25Kw), 115 Volts, 60 Hz, 1-Phase62M010PS411FR Motor, 0.33hp (0.25Kw), 115 Volts, 60 Hz, 1-Phase with Reversing 62M010PS423FN Motor, 0.38hp (0.28Kw),208−230/460 Volts, 60 Hz, 3-Phase 62M005PS411FN Motor, 0.33hp (0.25Kw), 115 Volts, 60 Hz, 1-Phase62M005PS411FR Motor, 0.33hp (0.25Kw), 115 Volts, 60 Hz, 1-Phase with Reversing 62M005PS423FNMotor, 0.38hp (0.28Kw),208−230/460 Volts, 60 Hz, 3-Phase62M180PSD3DEN Motor, 0.12 (0.09 Kw), 130 Volts DC 62M060PSD3DEN Motor, 0.25 (0.19 Kw), 130 Volts DC 62M030PSD3DEN Motor, 0.25 (0.19 Kw), 130 Volts DC 62M020PSD3DEN Motor, 0.25 (0.19 Kw), 130 Volts DC 62M010PSD3DEN Motor, 0.33 (0.25 Kw), 130 Volts DC 62M180PS423EN Motor, 0.17 (0.13 Kw), 230 Volts, 60Hz, 3−Phase VFD62M060PS423EN Motor, 0.17 (0.13 Kw), 230 Volts, 60Hz, 3−Phase VFD62M030PS423EN Motor, 0.38 (0.28 Kw), 230 Volts, 60Hz, 3−Phase VFD62M020PS423EN Motor, 0.38 (0.28 Kw), 230 Volts, 60Hz, 3−Phase VFD62M010PS423ENMotor, 0.38 (0.28 Kw), 230 Volts, 60Hz, 3−Phase VFD2917−078Key, Square, 0.188” x 0.75” LReturn PolicyNo returns will be accepted without prior written factory authorization. When calling for authorization, please have the following information ready for the Dorner Factory representative or your local distributor: and address of customer.2.Item(s) being returned.3.Reason for return.4.Customer’s original order number used when ordering the item(s).5.Dorner or distributor invoice number.A representative will discuss action to be taken on the Returned items and provide a Returned Goods Authorization Number to reference.There will be a 15% restocking charge on all new items returned for credit where Dorner was not at fault. These will not be accepted after 60 days from original invoice date. The restocking charge covers inspection, cleaning, disassembly, and reissuing to inventory.If a replacement is needed prior to evaluation of returned item, a purchase order must be issued. Credit (if any) is issued only after return and evaluation is complete.Dorner has representatives throughout the world. Feel free to contact Dorner for the name of your local representative. Our technical sales and service staff will gladly help with your questions on Dorner products.For a copy of Dorner’s Limited Warranty, contact factory, distributor, service center or visit our website at .。

Fagor Industrial LA-60 MP 洗衣机 '进化技术' 系列产品说明书

Fagor Industrial LA-60 MP 洗衣机 '进化技术' 系列产品说明书

DESPIECE TECNICOSERIES "EVOLUTION TECHNOLOGY"Modelos:LA-60 MPjun-09Fagor IndustrialMe12e5e4e3CN1CN 5CN 1020 V AC 0 V AC 20 V AC AC 24 V AC 0V+ 24 V DC GND 24 V DCVISUALIZACIONN'R'R'N'PNTCCN3CN11CN8CN2CN7CN9NTC 81234567anbgamvinaa vib am rs r na vi n ag an m r g ve na vi veb m vi r am vemmvePRGD .T .e11A A M /P +V D /ICVFSeñal Ready 13 ST 16Marcha/Paro 14AN1+ 1COM AN 8EQm rn m g R S TVFgam/vem n e2e7e1NRnIEIGaF amFIGvenR'N'na g viTRF e6ve I d e sna vi rs b I s cT MI p bI pAN1- 2Izq/Der 15Señal Ready 19Salida +24VDC 20 Contacto NC 28Contacto Común 29m b vi ram nT1T2viRST 17B AVAC2EP rmrsveP683040000R'N'PTC +-vig na M 1M 2COMUN +0VDC 21CVFVeMN'ra120kgVeC1R'naVAC1CT2VeC2naCT1A BSimb / LENG CT = DP =DS1DS2DS3D.T.e1 =e2 =e3 =e4 =e5 =e6 =e7 =e8 ,9,10 = e11 = EP =FI =F =G1,G2 = IE =IG = IGS = Ides = IMo =Ip =Ipb =IscM =Mo = NTC = RT = Tm = Trf = Trf s/N = VAC = Ve = VF = VM = 1…8 = COLORa = am = am/ve =b = g = m = n = na = r = rs = ve = vi =ESPAÑOLContactor CalentamientoDetector posición.Dosificador Neutralizante.Dosificador jabon liquido.Dosificador aditivos.Display/TecladoElectro válvula agua Fria.Electro válvula agua CalienteElectro válvula Prelavado.Electro válvula Lavado.Electro válvula Lejía.Electro válvula Suavizante.Electro válvula agua DescalcificadaElectro válvula EquilibradoElectro válvula Vapor.Electroimán de Puerta.Filtro de Interferencias.Fusible.Galga Sensor.Pulsador Parada de emergencia.Interruptor general.Interruptor General de seguridad.Interruptor de desequilibrio.Interruptor Monedero.Interruptor puerta Cerrada.Interruptor puerta bloqueada.Interruptor seguridad TemperaturaMotor.Monedero.Sensor temperatura..Resistencia Calentamiento.Térmico de Motor.TransformadorTransformador Versión sin Neutro.Válvula VaciadoVentilador.Convertidor de Frecuencia.Ventilador Motor.Puntos conexión dosificadores.COLORESAzulAmarilloAmarillo/verdeBlancoGrisMarrónNegroNaranjaRojoRosaVerdeVioletaFRANÇAISContacteur ChauffeDétecteur positionDoseur NeutralisantDoseur lessive liquideDoseur additifsÉcran/ClavierÉlectrovanne eau FroideÉlectrovanne eau ChaudeÉlectrovanne PrélavageÉlectrovanne LavageÉlectrovanne Eau de JavelÉlectrovanne AssouplissantÉlectrovanne eau AdoucieÉlectrovanne ÉquilibrageÉlectrovanne VapeurÉlectro-aimant de PorteFiltre Anti-parasitesFusibleJauge CapteurBouton-poussoir Arrêt d'urgenceInterrupteur généralinterrupteur Général de sécuritéInterrupteur de balourdInterrupteur MonnayeurInterrupteur porte FerméeInterrupteur porte verrouilléeThermostat LimiteurMoteurMonnayeurCapteur températureRésistance ChauffeThermique du MoteurTransformateurTransformateur Version sans NeutreVanne VidangeVentilateurConvertisseur de FréquenceVentilateur MoteurPoints raccordement doseursCOULEURSBleuJauneJaune / vertBlancGrisMarronNoirOrangeRougeRoseVertVioletENGLISHHeating ContactorPosition detectorNeutralizer feederLiquid soap feederAdditive feederDisplay/KeyboardCold water electrically operated valveHot water electrically operated valvePre-wash electrically operated valveWash electrically operated valveBleach electrically operated valve.Fabric softener electrically operated valveDelimed water electrically operated valveBalancer electrically operated valveSteam electrically operated valveDoor electric magnetInterference filterFuseSensing gageEmergency stop push buttonGeneral switchGeneral safety switchUnbalance switchCoin slote switchClosed door switchDoor lock switchHi-limit ThermostatMotorCoin slotTemperature sensorHeating ResistorsMotor hot-wireTransformerTransformer Version without NeutralEmptying valveFanFrequency converterFan motorFeeder connection pointsCOLOURBlueYellowYellow / greenWhiteGreyBrownBlackOrangeRedPinkGreenPurpleDEUTSCHHeizschützStellung TasterDosiervorrichtung NeutralspülmittelDosiervorrichtung FlüssigseifeDosiervorrichtung ZusatzmittelDisplay/TastaturElektroventil KaltwasserElektroventil WarmwasserElektroventil VorwaschenElektroventil HauptwaschgangElektroventil BleicheElektroventil WeichspülerElektroventil entkalktes WasserElektroventil GleichgewichtElektroventil DampfElektromagnet GerätetürStörungsfilterSicherungMeßsensorNot-Aus-TasterHauptschalterSicherheitshauptschalterUngleichgewichtsschalterMünzschalterSchalter Tür geschlossenSchalter Tür verriegeltGrenzthermostatMotorMünzvorrichtungTemperatursensorWiderstand AufheizungMotorwärmeschalterTransformatorTransformator Modell ohne NeutralstellungAblassventilVentilatorFrequenzumwandlerVentilator MotorAnschlussstellen DosiervorrichtungenFARBENBlauGelbGelb/grünWeißGrauBraunSchwarzOrangeRotRosaGrünViolettITALIANOContatore RiscaldamentoRilevatore posizioneDosatore NeutralizzanteDosatore sapone liquidoDosatore additiviDisplay/TastieraElettrovalvola acqua FreddaElettrovalvola acqua CaldaElettrovalvola PrelavaggioElettrovalvola LavaggioElettrovalvola CandegginaElettrovalvola AmmorbidenteElettrovalvola acqua DecalcificataElettrovalvola BilanciamentoEquilibrado VaporeElettromagnete PortaFiltro InterferenzeFusibileCalibro SensorePulsante Arresto di emergenzaInterruttore generaleInterruttore Generale di sicurezzaInterruttore di squilibrioInterruttore PortamoneteInterruttore porta ChiusaInterruttore porta bloccataTermostato LimitatoreMotorePortamoneteSensore temperaturaResistenza RiscaldamentoTermico del MotoreTrasformatoreTrasformatore Versione senza NeutroValvola ScaricoVentolaConvertitore di FrequenzaVentola MotorePunti connessione dosatoriCOLOREBluGialloGiallo/verdeBiancoGrigioMarroneNeroArancioRossoRoseoVerdeViolaLeyenda LAVADORAS HC-31347 P623014000。

Alsanfan HVLS 大气流扇产品介绍说明书

Alsanfan HVLS 大气流扇产品介绍说明书

HVLS FAN INDUSTRY6BLADESIndustrial Ceiling FansHVLS FAN INDUSTRYHigh Volume Low Speed Fan (6 Blades)Fancy Fan (8 Blades)Mobil Pivot Fancy Fan (6 Blades)Pivot Farm HVLS Fan (6 Blades)15913 HVLS FAN INDUSTRYWith the aerodynamic fan blade design that our company developed and designed in the early 2000s, our company has become one of the few companies in the world. Alsanfan works with the leading university in our country in terms of product development and fan performance. We have also added ceiling fans that we have completed R & D activities to our production portfolio. The constant principle of our company has always been quality service, on time delivery and reasonable price.What are Industrial Ceiling Fans (HVLS Fan) ?Alsanfan HVLS ceiling fans offers an innovative product that reduces heating-cooling costs in large-volume, high-ce-ilinged spaces. Alsanfan is capable of activating a high volume of air with low speed. With this feature, homogenous tempreture is obtained from floor to ceiling distribution of air stratification in high ceiling areas.At the same time, air is sent to the employees at a low speed to provide evoparative cooling (fan effect) without dis-turbing them, comfort and working hours are increased.HVLS fans are used in various industrial areas, commercial spaces, social spaces, factories, logistics warehouses, automotive service buildings, sports halls and residential areas by working in coordination with HVAC systems where energy saving is required with developing technology.12357647654321Double Angle Adjustable BracketSafety RopesEngine Housing And Protection Covers Belt Safety Hooks Steel Ring Seat BeltsFan Hub and Bottom Cover Aerodynamic Aluminum Blades1Fan Control Board:•Standard Speed C ontroller (Inverter).• External Touch Screen (HMI).• Inboard Ventilation And Temperature Control.•Add-on Fan Control Options ..Benefits of Celling Fans:Offer silent operation. Supply winter destratification and summer cooling.Offer multi-fan control and adjustable fan speed.Help reduce condensation on floors and equipments.Work coordinated with high velocity fans and other air conditioning systems.Assist in the removal of contaminant and heat.Cut energy consumption for heating. Provide eco-friendly and economic solutions.Require lower cost for investment, installation and maintenance than traditional cooling methods.Product Details :Fans are tested and simulated for best results.Safety Cable secures the fan to the mounting structure. Fan can be mounted to different construction profiles.Custom mounting systems for customersDesigned best for users safety and comfort.Body conducts heat into the air layer Summer CoolingBefore ProfanAfter ProfanHeated air collects at ceilingHVLS Fans Supply warm air destratificationBefore ProfanAfter ProfanCooling by air movementIE SUPERPremiumE ciencyIE5IE4IE3IE2Motor Efficiency ClassFan Diameterbetween Ø 8.2ft - 24ft(2.5m - 7.3m)• Saving up to 30% in summer.• Comfortable Coolness in Outdoor• 7.3m diameter fan sizes.•3m-6m Pole Fan Length Size3INVERTERCONTROLMOTORGEARREDUCER55d BA<45d BA<PERMANENTMAGNET6BLADESFan Control Board:Inboard Ventilation And Temperature Control.*Weight of fans change depending on the lenght and design of ceiling mounting brackets.*Coverage area is affected by objects such as obstructing the airflow. (columns, walls, machines, furnitures...)5Benefits of Celling Fans:Offer silent operation. Supply winter destratification and summer cooling.Offer multi-fan control and adjustable fan speed.Help reduce condensation on floors and equipments.Work coordinated with high velocity fans and other air conditioning systems.Assist in the removal of contaminant and heat.Cut energy consumption for heating. Provide eco-friendly and economic solutions.Require lower cost for investment, installation and maintenance than traditional cooling methods.8BLADESINVERTERCONTROLMOTOR123456123Double Angle Ceiling Mount Apparatus Engine Housing And Protection Cover Steel Safety Ropes456Belt Safety HooksSteel Ring Safety ConnectionsAerodynamic Aluminum BladesTechnical Details :6Benefits of Jumbo Fans:•Offers Easy and Safe Use.• Economical with Low Energy Consumption.• Enables Coolness in Wide Area with High Diameter.• Long And Healthy Engine Life With Reducer Design.•Wide Range of Color Options. (Colors with RAL Code)Product Details :• Designed best for users safety and comfort.• Protective wire grating is available as standard.• The most suitable materials were used in the tests.• Body length can be manufactured specially for the user.•Fan angle can be adjustable at certain limits to the enviroment which used.7INVERTERCONTROLMOTOR6BLADESFan Control Board:• Standard Speed C ontroller (Inverter).• External Touch Screen (HMI).• Inboard Ventilation And Temperature Control.•Add-on Fan Control Options ..Technical data :• Two different types of motors are available.• Water and Dust Resistant in Outdoor Areas.• 3 Year Warranty Period.•Powder Coating Painted Body.8Order Code Fan Diameter Ø (mm)Motor Power (KW)Covarage Area (m²)Maximum Speed (Rpm)Weight (kg)Maksimum Speed P.Consumption(KWh)Maximum SpeedCurrent (Amps)Airflow (m³/s)*Coverage area is affected by objects such as obstructing the airflow. (columns, walls, machines, furnitures...)T echnicial SpecificationsJfan16ft (1.83m)1501,51,323818414,56• Easy to use & Cycle Controlled • 6 Blades, 6 ft (1.80m) Fan Diameter • High Performance & Durability • Easy PortabilityBenefits of Mobile Pivot Fans :• Offers Easy and Safe Use.• Economical with Low Energy Consumption.• Provides Wide Area Cooling with 160 ° Swing Function.• Long And Healthy Engine Life With Reducer Design.•Convenient than current cooling systems in point of cost and usage.9INVERTERCONTROLMOTORProduct Details :Fans are tested and simulated for best results.Safety cage standardly available.Fan can be mounted to different construction profiles.Custom mounting solutionsDesigned best for users safety and comfort.6BLADESP�vot Soc�al FanMobile Pivot Fans1234510Fan Control Board:• Standard Speed C ontroller (Inverter).• External Touch Screen (HMI).• Inboard Ventilation And Temperature Control.•Add-on Fan Control Options ..Flexible Solutions for Ventilation at Every Place Flexible Pivoting Joints Allow Head Angle Adjustments Up to 160° of Airflow, Wide Coverage Area High Performance & Heavy Duty8 Blades, Fan Sizes up to 5ft (1.52m)P�vot Soc�al Fans11Benefits of Pivot Social FansOffer multi-fan control and adjustable fan speed.With oscillating head option, up to 160 degrees of airflow covers wide area.It offers high performance, heavy duty and affordable solutions.Assist in the removal of contaminant and heat. Help reduce condensation on floors and equipments.The fan can be easily pivoted up or down to aim in one direction for optimal air flow.Require lower cost for investment, installation and maintenance than traditional cooling methods.It is recommended for places where ceiling heigh is low. It offers flexible solutions for ventilation at every place.Product Details :Fans are tested and simulated for best results.Safety cage standardly available.Fan can be mounted to different construction profiles.Custom mounting solutionsDesigned best for users safety and comfort.• Up to 160° of Airflow, Wide Coverage Area • 8 Blades, Fan sizes up to 5ft (1.52m)• High Performance & Durability• Flexible Solutions for Ventilation at Every Place• Flexible Pivoting Joints Allow Head Angle Adjustments12INVERTERCONTROLMOTORAdjustable Ceiling or Column Mounting Bracket160° Oscillating FunctionInventer Control AC MotorHorizontal Pivot Adjustable HeadAerodynamic Aluminium Blades Galvanized Fan CageFan Control Board:• Standard Speed C ontroller (Inverter).• External Touch Screen (HMI).• Inboard Ventilation And Temperature Control.•Add-on Fan Control Options ..6BLADES123456• Cow Farms..• Chicken Farms..• Up to 25 % Increase on Milk Production of Dairy Cows.• Offers Cooling and Comfort for Dairy Cows.• Up to 160° of Airflow, Wide Coverage Area.• High Performance & Durability.•Reliable & Quiet Operation.13Pivot Farm FansBenefits of Pivot Farm FansOffer multi-fan control and adjustable fan speed.(Optionally required)With oscillating head option, up to 160 degrees of airflow covers wide area.It offers eco-friendly and affordable solutions.Assist in the removal of contaminant and heat. Help reduce condensation on floors and equipments.The fan can be easily pivoted up or down to aim in one direction for optimal air flow.15 °C is ideal ambient temperature for dairy cows’ milk production. Inconvenient conditions and hot weather effects negatively.Layer of warm air on body and blow flies annoy cows. However, Pivot Farm Fans distract them with maximum air movement andoffers cooling and comfort for dairy cows. Also Pivot Farm Fans sustain to increase productivity of them.• Ideal ambient tempreture for cows is 15 degrees. Hot ambient stress is a problem which causes low milk efficiency for cows. Heat layer and flies disturbs animals. Pivot Farm Fans moves away the heat layer and flies with air flow which is cause coolness and increase efficiency.14INVERTERCONTROLMOTOR6BLADESEye Bolts for Suspended MountingSteel FrameCeiling or Column Mounting Bracket 160° Oscillating Function Horizontal Pivot Adjustable Head Aerodynamic Aluminium BladesVee Belt Drive Motor or Gear Reducer AC MotorOrder Code Fan Diameter Ø (mm)Motor Power (KW)Coverage Area (m²)Maximum Speed (Rpm)Weight (kg)Maximum Speed P. Consumption(KWh)Maximum Speed System Current(Amps)Airflow (m³/s)*Weight of fans change depending on the lenght and design of mounting brackets.*Coverage area is affected by objects such as obstructing the airflow. (columns, walls, machines, furnitures...)T echnical SpecificationÇİFTLİK66ft (1.83m)2942.22150 -350110218•Our 6 Blade HVLS fans can be used in cow and chicken farms.• In summer you can relax in a more comfortable area as it provi-des coolness and relaxation on animals.• It plays an effective role in the fertilizer and soil ventilation.Remote ControllerOf FansHome Type Fans Of Alsanfan’s15Profan IstanbulModel: 93PRF-7046-A Light: Available/Led Diameter: 235 cmTimer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-RightMotor Power: 100 W Meteryal: Aluminyum Controller: Remote C. Coverage Area: 50m2PProfan ModernModel: 52PRF-3092-ALight: Available/Led Diameter: 132 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 38 W Meteryal: Wood Controller: Remote C. Coverage Area: 32m2Profan HisarModel: 52PRF-7063Light: Available/Led Diameter: 132 cmTimer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-RightMotor Power: 35 W Meteryal: Plastic Controller: Remote C. Coverage Area: 32m2PPProfan HardwoodModel: 52PRF-3092Light: -Diameter: 132 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 38 W Meteryal: Wood Controller: Remote C. Coverage Area: 32m2PProfan Hisar WhiteModel: 52PRF-7063-W Light: Available/Led Diameter: 132 cm Timer: 1/2/4/8 HoursSupply: AC100-250VRotation: Letf-Right Motor Power: 35 W Meteryal: Plastic Controller: Remote C. Coverage Area: 32m2PProfan Istanbul Brown MiniModel: 60PRF-7025-KALight: Available/Led Diameter: 152 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 96 W Meteryal: Aluminyum Controller: Remote C. Coverage Area: 32m2Profan Istanbul - Without LampModel: 93PRF-7046Light: -Diameter: 235 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 100 W Meteryal: Aluminyum Controller: Remote C. Coverage Area: 50m2Profan Istanbul BrownModel: 93PRF-7046-B Light: Available/Led Diameter: 235 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 100 W Meteryal: Aluminyum Controller: Remote C. Coverage Area: 50m2Profan Modern DarkModel: 52PRF-3092-DA Light: Available/Led Diameter: 132 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 38 W Meteryal: Wood Controller: Remote C. Coverage Area: 32m2Profan Istanbul OutdoorModel: 93PRF-7046-W Light: -Diameter: 235 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 100 W Meteryal: Aluminyum Controller: Remote C. Coverage Area: 50m2PrProfan Istanbul MiniModel: 60PRF-7025-A Light: Available/Led Diameter: 152 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 100 W Meteryal: Aluminyum Controller: Remote C. Coverage Area: 35m2PHVLS FAN INDUSTRY16Profan ChichtWe C.2m2htWe C.2m2Profan BosphorusModel: 52PRF-7062-B Light: Available/Led Diameter: 132 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 35 W Meteryal: Plastic Controller: Remote C.Coverage Area: 32m2Profan StormModel: 56PRF-820 Light: Available/Led Diameter: 142cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 40W Meteryal: PlasticController: Remote C. Coverage Area: 42m2Profan GalataModel: 52PRF-002-B Light: -Diameter: 135 cm Timer: -Supply: AC100-250VRotation: Letf-Right Motor Power: 80 W Meteryal: WoodController: Manual Coverage Area: 30m2Profan RetroModel: 52PRF-002Light: -Diameter: 132 cm Timer: -Supply: AC100-250VRotation: Letf-Right Motor Power: 70 W Meteryal: WoodController: Manual Coverage Area: 32m2Profan FrostyModel: 52PRF-1008Light: Available/Led Diameter: 132 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 35 W Meteryal: Plastic Controller: Remote C. Coverage Area: 32m2htWe C.2m2Profan FunnyModel: 52PRF-1060Light: Available Diameter: 107 cm Timer: -Supply: AC100-250VRotation: Letf-Right Motor Power: 100 W Meteryal: Wood Controller: ManualCoverage Area: 30m2Profan SunnyModel: 52PRF-1060-A Light: Available Diameter: 107 cm Timer: -Supply: AC100-250VRotation: Letf-Right Motor Power: 35 W Meteryal: Wood Controller: Manual Coverage Area: 30m2htWe C.2m2Profan Bosphorus SteelModel: 52PRF-7062-MS Light: Available/Led Diameter: 132 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 35 W Meteryal: PlasticController: Remote C. Coverage Area: 32m2Profan DaisyModel: 65PRF-801-DC Light: Available/Led Diameter: 165 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 38 W Meteryal: Wood Controller: Remote C. Coverage Area: 42m2Model: 52PRF-811Light: Available/Led Diameter: 132 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 32 W Meteryal: Plastic Controller: Remote C. Coverage Area: 32m2htWe C.2m2Profan ActiveModel: 52PRF-868Light: Available/Led Diameter: 132 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 35 W Meteryal: PlasticController: Remote C. Coverage Area: 32m2Profan DarkModel: 56PRF-821-B Light: -Diameter: 140 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 22 W Meteryal: PlasticController: Remote C. Coverage Area: 35m2Profan WhiteModel: 56PRF-821-W Light: -Diameter: 140 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 22 W Meteryal: Plastic Controller: Remote C. Coverage Area: 35m2Profan Bosphorus WhiteModel: 52PRF-7062-W Light: Available/Led Diameter: 132 cm Timer: 1/2/4/8 Hours Supply: AC100-250VRotation: Letf-Right Motor Power: 35 W Meteryal: Aluminyum Controller: Remote C. Coverage Area: 32m2Ikitelli Atatürk Mah. Marmara San. Sit. S Blok No:8 Küçükçekmece - Istanbul / TURKEY Tel: (0212) 494 25 25 Fax: (0212) 494 45 97*****************//alsanfanHVLS FAN INDUSTRY。

SFA60UP60DN(Rev.02)

SFA60UP60DN(Rev.02)

1/3
www. sunnychip. com
Dec. 2014
SFA60UP60DN --Ultrafast Dual Diode
Electrical Characteristics per diode @TC=25 ℃ unless otherwise noted
Symbol VF IR Trr EAS Parameter Forward Voltage Drop Reverse Leakage Current Reverse Recovery Time Avalanche Energy Conditions IF=30A IF=30A, TC=125℃ VR=600V IF=30A, di/dt=-200A/us L=30mH Min. 20 Typ. 1.2 Max. 1.5 1.4 100 90 Unit V V uA ns mJ
Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Average Rectified Forward Current Non-repetitive Peak Surge Current Operating Junction Temperature Range Storage Temperature Range
Applications
• Welder & UPS & Inverter • Switching Power Supply • FWD for Motor Application
Package Type & Internal Circuit
1. Anode 2.Cathode 3.Anode

Eaton FERRUPS UPS FE系列60Hz产品简介说明书

Eaton FERRUPS UPS FE系列60Hz产品简介说明书

Eaton FERRUPS UPS FE Series 60 HzProduct SnapshotProduct rating: 500 VA–18 kVAInput voltage 120/208/240,208/240 Output voltage 120/208/240 Frequency: 60 HzConfiguration: Cabinet Features• Active voltage regulation converts power from almost any AC source into computer grade power• Eliminates harmful harmonic currents from entering a building’s wiring, where they can disrupt computer operations• Enhanced diagnostics initiates automatic startup and scheduled tests on the logic board, battery and other critical systems• Provides regulated output voltage without drawing power from batteries keeping the batteries full charged from unexpectedblackouts• Complete offering of LanSafe® power management software included to ensure data integrity• Provides investment protection with a two-year limited warranty and a $250,000 load protection guarantee (US and Canada)Eaton® FERRUPS®uninterruptible power systemsfurnish unmatched reliabilityin configurable powerprotection for computers andtelecommunications equipment.Patented ferroresonanttechnology delivers“bulletproof” power protection,overcoming spikes, sags,surges, noise and lightning.Eaton-exclusive SineSenseprovides clean, reliable powerwhile conserving batteriesduring blackouts.Extensive configurability optionsmake FERRUPS the ideal powerprotection solution with a widerange of voltages, frequencies,runtimes, power cords andreceptacles. FERRUPS preventsthe backfeed of harmoniccurrents into building wiringwhich can disrupt computeroperations.Redundant power pathsassure high fault-toleranceand optimum uptime. Galvanicisolation separates input fromoutput, filtering line noise andsurges. FERRUPS also featuresprecision voltage regulation withno battery discharge down to38% below nominal (dependingupon load) as well as over 80user-programmable diagnosticand communications functions.FERRUPS models include freeEaton Software Suite powermanagement software withconnectivity cable and areBestLink SNMP/Web-ready forremote management. FERRUPScovers up to $250,000for damage to connectedequipment resulting from aspike or surge (US and Canadaonly).FE SERIES, 60 HZ SPECIFICATIONSModels 500 VA 700 VA 850 VA 1.15 kVA 1.4 kVA 1.8 kVA 2.1 kVA 3.1 kVA 4.3 kVA 5.3 kVA 7 kVA 10 kVA 12.5 kVA 18 kVAPart number FE500 VA FE700 VA FE850 VA FE1.15 kVA FE1.4 kVA FE1.8 kVA FE2.1 kVA FE3.1 kVA FE4.3 kVA FE5.3 kVA FE7 kVA FE10 kVA FE12.5 kVA FE18 kVACapacity (kVA/kW).5/.35 .7/.5 .85/.6 1.15/.8 1.4/1 1.8/1.25 2.1/1.5 3.1/2.2 4.3/3 5.3/3.7 7/5 10/7.5 12.5/10 18/15Dimensions H x W x D (inches)12 x 10 x 21.25 15.1 x 15.2 x 20.2 21.2 x 15.25 x 22.9 29.5 x 15.5 x 25 36.5 x 19 x 32** (mm)305 x 255 x 540 385 x 390 x 515540 x 390 x 585 750 x 395 x 635930 x 485 x 815**Weight (lb) 54 62 67 102 122 176 188 248 348 484 578 875 1089 1362(kg) 2528 30 46 55 8085112158220262 397 494 618Input connection6-ft cord 6-ft cord 120V/40A 120V/50A 120V/70A6-ft cord w/NEMA 5-15P* w/NEMA w/NEMA 208V/25A 208V/30A 208V/40A 208V/60A 208V/80A 208V/110A5-20P*L5-30P* 240V/20A 240V/25A 240V/35A 240V/50A 240V/70A 240V/100AOutput connection(4) NEMA 5-15R (6) NEMA 5-15R (6) NEMA 5-15RH ardwired output is standard—Typical runtime, minutes (full load) 9 11 9 8 11 11 9 14 10 20 12 11 18 10 (half load) 2531252231302535245033 26 48 26OperationNominal input voltage 120 120/208/240 208/240 Input vol t age range +15%, -20%Input power factor 0.98 Nominal output voltage 120 120/208/240 Output voltage regulation ±3% for input voltages of +15% to -20%Output voltage waveformSine waveOutput voltage THD 5% or less at rated kW load Overload capacity 150% surge and 125% for 10 minutes online, 150% surge and 110% for 10 minutes on inverterTransfer time0 msLightning, surge & noise protection 2000:1 spike attenuation using ANSI/IEEE C62.41 and C62.45 Category A and Category B testsC ommon mode: >120 dB. Normal mode: >60 dB Efficiency 85 86 85 88 88 90 90 91 90 90 90 90 91 92Safety certification UL, CSA (cUL)EMI complianceFCC Class ATesting standards A NSI/EEE C62.41 (1991); ANSI/EEE C62.45 (2002); EN62040-2CommunicationRS-232 serial port (DB25), plus contact closuresEnvironmental Operating temperature 0°C to 40°C (32°F to 104°F) Storage temperature -20°C to + 60°C (-4°F to 140°F)Relative humidity 5 to 95% without condensation Audible noise at 1m (dB) 41 41 47 49 4951515150 51 54 61 61 61Altitude3,050m (10,000 ft) maximumDue to continuing product improvement programs, all specifications are subject to change without notice. *120V standard configuration. **Batteries in second cabinet. Contact factory for weights and dimensions.for additional recetacle selections, refer to FERRUPS CTO Guide (hardwired input is standard for FE1.8 kVA and above)EatonElectrical Sector1000 Eaton Boulevard Cleveland, OH 44122 USA /powerquality © 2014 EatonAll Rights Reserved Printed in USA BR153035EN May 2014Eaton, LanSafe and FERRUPS are registered trademarks of Eaton.All other trademarks are property of their respective owners.。

安物 Kingdomtech HC60W35R2 HC60W35R4 5MP网络圆顶室内摄像头说明书

安物 Kingdomtech HC60W35R2 HC60W35R4 5MP网络圆顶室内摄像头说明书

Relative Humidity
Less than 90 %, non-condensing
Ingress Protection
IP 52
Impact Resistance
IK 10 (bubble only)
REGULATORY
Emissions
FCC PART 15, CE (EN 55032)
Frame Rate Third Stream
Bit Rate (Control)
AUDIO
Audio Compression Audio Stream Audio Interface
HC60W35R2
HC60W35R4
NTSC / PAL
Progressive
1/2.8” CMOS (5.18 x 3.89 mm)
Lens
Angle Of View G-Sensor Privacy Masking Defog Encryption Chipset
Local Storage
Micro USB
VIDEO
Video Compression
Resolution (16/9)
Resolution (4/3) Number of Video Streams Frame Rate Main Stream & Frame Rate Second Stream
2560 x 1440 / 1920 x 1080 / 1600 x 904 / 1360 x 768 / 1280 x 720 / 640 x 360
2560 x 1920 / 1600 x 1200 / 1280 x 960 / 640 x 480
3
2560 x 1440 / 1920 x 1080 / 1600 x 904 / 1360 x 768 / 1280 x 720 / 640 x 360 (1-25/30 fps), 1920 x 1080 / 1600 x 904 / 1360 x 768 / 1280 x 720 / 640 x 360 (1-50/60 fps), 2560 x 1440 (1-50 fps)

Fujifilm F660EXR 15倍光学缩放摄影机用户手册说明书

Fujifilm F660EXR 15倍光学缩放摄影机用户手册说明书

• A/V cable • CD-ROM • Owner's manual
SD™/SDHC™/SDXC™ Memory Cards (2GB - 64GB)
• Mini-HDMI/HDMI Cable
P10NA02930A
• SD™/SDHC™/SDXC™ Memory Cards (2GB-64GB)
Aperture F3.5/F7.1/F10 (Wide) F5.3/F11/F16 (Telephoto) with ND filter
Focus distance Normal: (from lens surface)
Macro:
Wide: Approx. 45cm / 1.4 ft. to infinity Telephoto: Approx. 2.5m / 8.2 ft. to infinity Wide: Approx. 5cm - 3.0m / 1.9 in. - 9.8ft. Telephoto: Approx. 1.2m - 3.0m / 3.9ft. - 9.8ft.
Travel zoom compact camera Aimed at gadget lovers, who like to travel, the F660EXR is a compact, 15x optical zoom camera with a whole host of exciting features. Combining a 16 megapixel EXR-CMOS sensor with features such as 30x Intelligent Digital Zoom, Face Tracking Auto Focus and 11fps continuous shooting means that whether the subject matter is standing still or on the move, the images will be crisp and clear. What's more with Full 1080p HD movie capture, 3D Shooting mode, a high contrast 3.0inch LCD screen and Motion Panorama 360, this digital camera will be perfect to capture a vast range of photographs.
  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

FFA60UP60DN Ultrafast Recovery Power Rectifier
FFA60UP60DN Ultrafast Recovery Power Rectifier
Electrical Characteristics (per diode) T C
= 25°C unless otherwise noted
* Pulse Test: Pulse Width = 300µs, Duty Cycle = 2%
Package Marking and Ordering Information
Symbol Parameter
Min.Typ.Max.Units V FM *
Maximum Instantaneous Forward Voltage
I F = 30A T C = 25 °C T C = 125 °C 2.32.1V V I RM *
Maximum Instantaneous Reverse Current
@ rated V R T C = 25 °C T C = 125 °C
15150µA µA t rr Maximum Reverse Recovery Time (I F = 1A, di/dt = 100A/µs)
70nS t rr t rr I rr Q rr Maximum Reverse Recovery Time (I F = 30A, di/dt = 200A/µs)
T C = 25 °C T C = 100 °C T C = 25 °C T C = 25 °C 901508360
nS nS A nC W AVL
Avalanche Energy (L = 40mH)20
mJ
Device Marking
Device
Package
Reel Size
Tape Width
Quantity
F60UP60DN
FFA60UP60DN
TO-3P
-
-
30
FFA60UP60DN Ultrafast Recovery Power Rectifier
FFA60UP60DN Ultrafast Recovery Power Rectifier
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks.
FFA60UP60DN Ultrafast Recovery Power Rectifier
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.As used herein:
1. Life support devices or systems are devices or systems which,(a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling,can be reasonably expected to result in significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
PRODUCT STATUS DEFINITIONS Definition of Terms
Datasheet Identification Product Status Definition
Advance Information
Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice.
Preliminary
First Production
This datasheet contains preliminary data, and
supplementary data will be published at a later date.Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design.
No Identification Needed Full Production
This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design.Obsolete Not In Production
This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor.The datasheet is printed for reference information only.
FAST ®FASTr™FPS™FRFET™
GlobalOptoisolator™GTO™HiSeC™I 2C™i-Lo ™
ImpliedDisconnect™IntelliMAX™
ISOPLANAR™LittleFET™
MICROCOUPLER™MicroFET™MicroPak™MICROWIRE™MSX™MSXPro™OCX™OCXPro™OPTOLOGIC ®OPTOPLANAR™PACMAN™POP™
Power247™PowerEdge™PowerSaver™PowerTrench ®QFET ®QS™
QT Optoelectronics™Quiet Series™RapidConfigure™RapidConnect™µSerDes™
SILENT SWITCHER ®SMART START™SPM™Stealth™SuperFET™SuperSOT™-3SuperSOT™-6
SuperSOT™-8SyncFET™TinyLogic ®TINYOPTO™TruTranslation™UHC™UltraFET ®UniFET™VCX™Wire™
ACEx™
ActiveArray™Bottomless™Build it Now™CoolFET™
CROSSVOLT ™DOME™
EcoSPARK™E 2CMOS™EnSigna™FACT™
FACT Quiet Series™
Across the board. Around the world.™The Power Franchise ®
Programmable Active Droop™
Rev. I16。

相关文档
最新文档