步进电机：35BYJ46规格书

ELECTRIC PERFORMANCE & PROPERTIES:
1.1、相数：
4相。
Number of phase:
4 phase.
1.2、驱动方式：
1-2相励磁单极驱动。
Drive mode:
1-2 phase excitation unipolar drive.
1.3、步距角：
7.5°/85(输出轴),减速比1/85。
约70克。
Weight:
Product shall weight about 70g.
2.4、噪音：
雷利电器LEILI
3
40dB以下，12V DC，100pps，无负载，距电机10cm处测得。 Noise level:
Noise level of motor shall be less than 40dB energized with 12V DC and 100pps in no load condition measured 10 centimeters from motor. 2.5、输出轴机械强度： •受垂直轴向载荷(输出轴前端)：
1.9、绝缘电阻：
在常温状态下，接线与机壳间 DC 500V，10MΩ以上，
雷利电器LEILI
2
在湿热试验后，接线与机壳间 DC 500V，10MΩ以上。
Insulation resistance:
Insulation resistance between motor connector pin and dead metal parts
3.4、环境试验： Environmental test: 环境试验后的性能须满足1.8～1.10，2.1，2.4～2.7。 Motor shall satisfy requirements in 1.8～1.10,2.1,2.4～2.7 after environmental test. 3.4.1、高温、高湿试验： 85℃,95%RH中放置100h,取出在常温中放置30min后进行测试。 High temperature & high humidity test: Motor stored in ambient condition of 85℃,95% relative humidity for 100 hours then picked out and stored in normal ambient condition for 30 minutes.
shaft end without failure for 10 seconds. •Pull out force:
Output shaft must withstand 19.6N(2kgf) pull out force to the shaft end without failure for 10 seconds. •Push on force:
确认人(ACKNOWLEDGED)：
产品用户单位(CUSTOMER)： 杭州九阳
盖 章(SEAL)：
确认记载项目： 1、电性能及参数。 2、机械性能。 3、环境性能。 4、使用寿命试验。 5、附录。
AFFIRM THE FOLLOWING ITEMS 1. ELECTRIC PERFORMANCE AND PROPERTIES. 2. MECHANICAL PERFORMANCE AND PROPERTIES. 3. ENVIRONMENTAL PERFORMANCE AND PROPERTIES. 4. ENDURANCE TEST. 5. APPENDICES.
Applied voltage
Time
Leak current
600VAC 50/60Hz
1 second
1mA
1.11、绝缘等级：
E级。
Insulation class:
Class E .
1.12、线圈温升：
45K以下，线圈电阻120+80Ω/相，8.6V DC，100pps，阻抗法测量。 Temperature rise of motor bobbin coil:
shall be over 10MΩ measured with 500V DC megohmmeter in normal ambient
condition.
Insulation resistance between motor connector pin and dead metal parts
DRAWN
CHECKED
APPROVED
杨科峰 2009-12-31
产品供货单位(SUPPLIER)：
常州雷利电器有限公司
于 年 月 日确认此规格书
ACKNOWLEDGEMENT DATE :
/MONTH
/DAY
/YEAR
CHANGZHOU LEILI ELECTRICAL EQUIPMENT CO., LTD
may cause failure at rated operating conditions.
2.2、结构及尺寸：
见参考附图。
Motor structure and size:
Outside view, structure and size shall match the drawings.
2.3、重量：
measured by resistance method.
2、机械特性：
MECHANICAL PERFORMANCE AND PROPERTIES:
2.1、外观：
按额定使用状态下无引起整机使用不良的生锈或变形。
Outside view:
Outside view shall be free from a damage and discoloration which
shall be over 10MΩ measured with 500V DC megohmmeter after humidity test.
1.10、绝缘耐压：
AC 600V 1秒内，接线与机壳间，漏电流设定为1mA.(无击穿或飞弧)。
Dielectric breakdown of insulation
Alternating potential is applied between motor connector pin and dead
metal under the following condition and requirement. Product shall
show no abnormal indication.
Output shaft must withstand 19.6N(2kgf) push on force to the shaft end without failure for 10 seconds. 2.6、引出线插拔强度： 引出线与电机端加9.8N(1kgf)以上/根，10s静载，无异常。 引出线和插头间加9.8N(1kgf)以上，无异常。 Lead wire pulling strength: The motor lead wire shall withstan8N (1kgf) for 10s each lead without failure. The motor shall withstand a static pull out load more than 9.8N(1kgf)/piece between motor lead and connector without failure. 2.7、定位转矩： 44.1mN.m(450gf.cm) 以上。 Detent torque: Static detent torque shall be over than 44.1mN.m(450gf.cm). 3、环境性能： ENVIRONMENTAL PERFORMANCE & PROPERTIES: 3.1、使用温度范围： Operating conditions range: 1.5，1.9，1.10，2.1，2.2必须满足以下条件。 Motor shall satisfy requirements in 1.5,1.9,1.10,2.1,2.2 in operating. conditions. •温度：
Temperature rise of motor bobbin coil shall not exceed 45K,resistance
is 120+80Ω per phase,when operated in no load condition at 8.6V DC and 100pps ,until temperature rise of motor bobbin coil gets constant,
3.3、标准状态： Test conditions shall be as follows: •温度： 20±1℃。 •Temperature: 20±1℃. •湿度： 63%～67%RH。 •Relative humidity: 63%～67%RH. 但是在对测试结果判定无疑议的情况下，1.5、1.9、1.10、2.1、2.2以外的 试验是在常温(5～35℃)和常湿(45%～85%RH)中进行。 These condition is applied to requirements in 1.5,1.9,1.10,2.1,2.2. Actual test conditions of 5～35℃, 45～85%RH in applicable as far as test results are reliable.
Step angle:
7.5deg/85(output shaft), gear reduction ratio:1/85.
1.4、电压：
12V DC(电机端子)。
Voltage:
12V DC (motor energized voltage).
1.5、线圈电阻(每相)：
120+80Ω/相， 25℃时。 Resistance per phase:
-5～40℃。
雷利电器LEILI
4
•Temperature: -5～40℃.
•湿度： 45%～85%RH。
•Relative humidity: 45%～85%RH.
3.2、储存条件： Storage condition: •温度： -20～60℃。 •Temperature: -20～60℃. •湿度： 不大于75%RH。 •Relative humidity: Less than 75%RH.
19.6N(2kgf) 静载荷10秒内正常。 •受轴向拉力：
19.6N(2kgf) 静载荷10秒内正常。 •受轴向压力：
19.6N(2kgf) 静载荷10秒内正常。 Output shaft mechanical strength:
•Radial force: Output shaft must withstand 19.6N(2kgf) radial force to the
交货规格书
SUBMISSION OF SPECIFICATIONS
产品名称(PRODUCT NAME )： 步进电机 (STEPPING MOTOR)
产品型号(SUPPLIER'S PART NAME ): 35BYJ46-607
客户部品号(USER’S PART NUMBER ):
1
编制
校对
审核
用户确户(ACKNOWLEDGEMENT)：
Max starting frequency:
More than 350pps at 7.4VDC,measurement at coil state.
1.8、牵入转矩：
100pps，7.4VDC时，147mN.m(1.5Kgf.cm)以上，量程353mN.m测矩计测量；
98mN.m(1.0Kgf.cm)以上，砝码盘测量，以上均在冷态测量。
雷利电器LEILI
1
交货规格书
Submission of Specifications
制图日 DATE
2009-12-31
用户 NAME
杭州九阳
电机型号 MOTOR MODEL
35BYJ46-607 STEPPING MOTOR
图纸编号
35BJ46-607.0.0-00WX
DRAWING №.
1、电性能及参数：
120+80Ω/phase at 25℃. 1.6、最大空载牵出频率：
7.4VDC时，350pps以上，冷态测量。
Max response frequency:
More than 350pps at 7.4VDC,measurement at coil state.
1.7、最大空载牵入频率：
7.4VDC时，350pps以上，冷态测量。
tjc35y白b2014接线柱6cp镀锡钢丝13线路板1敷铜板1012出线盒1abs11铭牌1亚银聚酯薄膜111910绕组13uew聚胺酯漆包线9弹簧片1不锈钢8芯轴11不锈钢7注塑体1pom4520c17186磁环1ndfebc5下骨架1尼龙pa66174上骨架13中极板2耐指纹膜镀锌钢板2上极板1耐指纹膜镀锌钢板121314161机壳1耐指纹膜镀锌钢板表面镀镍处理