T30 Trainer Airplane Instruction Manual

T30 Trainer Airplane Instruction Manual
工具 Tools Needed
F1
F2F3爪牙螺母Claw nut
F7-3F7-2F7-1
F21
F4
F5F6
F13
F8
F9
F14F14-1
F15F15-1
F21
F11
F12F10
F16
F12-1
F22
F17
F27
F28
F29
F18
F19
F20
F38
P4
F40
F23
F30
F25
F26
F24
F23-1
P5
F32F33
F34
F35
F36
P3F32-1
F37F37-1
F31F14F14-1F14-2
背面装爪牙螺母
打磨成机身一体弧度
螺丝固定
碳杆
carbon rod
磁铁magnet
磁铁magnet
R4
E8E3E4
E1
E7
E6
E5E2
E9
E10
R11R10
R9R5R7
R6
R1x2R2
R3
R8
R12
W21
W22W4-1W23
W16
W17W17-1
W19
W20
W13x2
W38x3
W20-1x3
W16-1
W24W25
W26W28W27
W293,机翼组装 Assemble the Wing
W51,机身组装 Assemble the Fuselage
Claw nut
爪牙螺母Claw nut
爪牙螺母Claw nut
爪牙螺母F30 F40粘贴时用水湿润后再进行蒙板粘贴
Soak the F30 and F40,and paste the cover board.
Firm with screws
螺丝固定
Firm with screws
install the claw nut at the back.
Polish it with same radian as fuselage
Assemble the wing and tail on the smooth desk,make sure the wing is straight.
参数
翼展：1400mm 机长：1070mm
起飞重量：≈2000-2500g
推荐配置
马达：2814-3520 600-1000KV 电调：40A
电池：4S 3600-5000mAh 舵机：17g*4引擎：2C36 / 4C56桨叶：10-12inch 通道：≥4CH
Speci�ication
Wingspan: 1400mm Length: 1070mm
Flying Weight ≈2000-2500g
Suggested Equipment
Electric powered: 2814-3520 600-1000kv ESC: 40A
Battery: 4S 3600-5000mAh Servos: 17g*4
Gas engine class: 2C36 / 4C56Propeller: 10-12inch Radio≥4CH
W32W30
W30-1
W36
W15x2W32-1
W12W35-1
W35
W37
W21x3
（按机翼弧度打磨成弧形）
W33W33-1
W34
W31-1
W31
D3x2
D2
D2
D4
D1
D6D5
螺丝screw 插入Insert
8,重心调试位置图示 Adjust the C.G.
升降舵舵机副翼舵机
X1*2
X2X3垫入X1-3并打磨 C.G
≈80mm
(Polish as per the radian of the wing)
(Paste the W12 only with W35)
（W12只与W35粘贴）
D4可根据选用的马达长度进行增加或减少。

The length of D4 could be Firm the motor mount onto the head with screws.
Elevator servo
转向舵舵机
Connect the rudder servo with the front steering wheel.
When it's powered by gasoline,this servo controls the throttle.
连接前转向轮
使用油动马达时，此舵机控制油门
Aileron servo。