Infolytica Erroe code

Solution error messagesNote This table includes both 2D and 3D error messages.Error number Error message100001 An error occurred during the error recover process for adaption. The adaption process was aborted. However, there may be a valid solution if one or moreadaption steps had already completed successfully.100010 The specified volume label and coupled field node are not associated.100012 The mass density material property is unavailable for calculating iron loss.132000 Cholesky decomposition failed.132001 Error in Cholesky decomposition. Invalid Sparsity Pattern.134001 Non-Linear J-E DLL is unlicensed.134002 Non-Linear H-B DLL is unlicensed.139005 An error occurred writing to a file. The disk drive containing your temporaryfolder is probably full.140081 Hysteresis DLL is unlicensed.140082 Non-Linear E-J DLL is unlicensed.initial triangulation.creating145000 ErrorRefine the mesh to correct the problem.self-overlap.element145001 Parametricproducedduplicate or overlapping elements.triangulation145002 Initialdetected in motion mesh.145003 Collisionconstraintscannot be applied to faces in the plane of a 2D solution. 145004 Binary145006 Mesh has no elements.145007 Error constructing the remesh region solid model.145008 There is a hole in your model that is not constrained. There may be anunintentional gap between components.145009 An unmatched periodic boundary condition has been found; check binarytransformation.145011 The assigned material for all motion re-mesh regions must be AIR.Please refer toz Setting up motion modelsz Modeling Tips for Transient with Motion145020 The motion component setup is invalid; check the topology of the remeshregion.148002 The components of a coil do not appear in the model (material) mesh. Thiserror will occur if components of a coil have not been swept in the samedirection as the rest of the model.148003 A circuit component (either a resistor, capacitor or an inductor) does not have a positive, non-zero value.148005 Circuit component type not recognized.148006 A voltage or current source has an invalid waveform for this solution type. This error will occur during a magnetostatic solution if a source has a non-sinusoidalwaveform.148007 Definition of commutator component is non-physical (sectors or brushesoverlap, or commutator is not linked to a motion component).148009 Coils with more than two terminals cannot be used in any 2D solver.148010 The times specified in a switch are invalid. They must be sorted in ascending order and periodic switches must have 3 or more times.148102 ThermNet component cannot be disabled in MagNet when using the samemesh in a coupled solution.148201 Two constraints are applied to the same surface.148202 A Thin Plate constraint is applied to an exterior surface.148203 An exterior only type constraint is applied to an interior surface.149001 Error in Tet_Num_Fnodes. Tetrahedron type not known.149002 Negative or zero volume tetrahedron in coil mesh.149003 Error (condition 1) in intersecting coil mesh with material mesh.149004 Error (condition 2) in intersecting coil mesh with material mesh.149005 Error: Count_Complete is not equal to the number of edges. This error occurs when the solver is unable to complete its generation of the coil field Hs. Usuallythis error occurs for a model with a hole through it (as in a doughnut shape)when the surface of the hole does not have the Field Normal boundarycondition applied to it. The Field Normal boundary condition should be appliedto the surface of the hole.149006 Negative or zero volume tetrahedron in the material mesh.matrix.149007 Non-invertible149010 Problem type not supported.149011 Binary edges could not be completed.149012 There are coil tetrahedra outside the material mesh. The coil must not extend past the outer boundary of the model.149013 Edge ready for completion remaining.149014 Edge with 2 incomplete nodes remaining.149015 Error 2 in GENFNO. Part type not known.149016 Limit on the number of field nodes exceeded.Invalid problem type for this solver.149017 to149020149021 Singular matrix in LU decomposition.149022 Zero resistance in a voltage-driven coil in a non-conducting region.149023 No convergence in the non-linear solution. Cannot continue the solution. 149024 Error reading the material.149025 Zero or negative conductivity in COND.DAT.149026 Error inverting the conductivity matrix.149027 Error reading the time instant.149028 Error reading the current/voltage waveform.149029 A periodic constraint adjacent to a conductor must have conductor adjacent to both the master and slave faces.149030 Limit on the number of unary edge constraints exceeded.149031 Maximum number of tetrahedra sharing a field node is exceeded. This error occurs if a large number of tetrahedra are joined together at a single meshvertex. Changing the mesh edge subdivisions in the area may fix the problem. 149032 Limit on the matrix size exceeded.149033 Limit on the number of field nodes + voltage-driven coils exceeded.149034 Error 1 in GEPALF. Part type not known.149035 Fatal error 1 in field node generation.149036 Fatal error 2 in field node generation.149037 All bad elements have maximum order.149038 Error reading file COND.DAT.149039 Error writing to disk. This error usually means that your computer does nothave sufficient disk space to run the problem. Please make sure that there isenough disk space both on the drive where the program is run and on the drivewhere the TMP directory is located. See the installation section of the GettingStarted Guide for more information.149041 An invalid circuit component for static problems.149044 Each circuit should contain a coil.149045 Each circuit should contain either a current source or a voltage source. 149046 A loose circuit branch exists in the circuit.149047 Error in using the user material database hyster.dll.149048 Coils should be made of conducting materials.149049 There are over 1000 tets sharing the same node.149052 A current source connected to more than one terminal pair cannot be solved with the static solver. Use separate current sources for each terminal pair oruse the time-harmonic solver.149053 The static solver doesn't support voltage driven sources.149056 Shared field nodes have different geometric coordinates.149057 Inconsistent data between FnodeTet and TetFnode.149058 A material does not have specific heat density values defined.149059 A material does not have mass density values defined.149060 A material does not have thermal conductivity values defined.149061 A coil using a coil mesh appears in series with a coil not using a coil mesh.Check the coil parameter named UseCoilMesh.149062 A coil that does not use a coil mesh has the parameterUseCoilMeshDCResistance set to No.149063 The limit on the number of binary edge constraints was exceeded.149064 The limit on the number of binary edge constraints was exceeded.149067 Memory allocation failed for a large vector or matrix in the 3D solver. Refer to the SolverLog.txt for details.149070 It is illegal for electrodes to touch.149072 Unhandled binary constraint case. Contact Infolytica Support.149073 One side of the convective gap constraint has no mesh elements.149074 The circuit contains invalid connections, ex: two current sources connected to the same coil.149075 The solver has encountered a non-physical situation in the problemspecification.149076 Unable to load the DLL specified in the SolverDllNonlinearHB parameter or one of its required functions cannot be found.149077 Unable to load the DLL specified in the SolverDllNonlinearJE parameter or one of its required functions cannot be found.149078 Unable to load the DLL specified in the SolverDllNonlinearEJ parameter or one of its required functions cannot be found.149079 Unable to load the DLL specified in the SolverDllHysteresis parameter or one of its required functions cannot be found.149081 There is no path from the start terminal to the end terminal of at least one of the current sources, which does not pass through another current source, or nopath exists.149085 Nonlinear surface impedance must be applied to a material with isotropicconductivity.149086 Nonlinear surface impedance must be applied to a material with linearconductivity.149087 Nonlinear surface impedance must be applied to a material with isotropicpermeability.149088 Internal error due to nonlinear surface impedance.149089 Internal error due to nonlinear surface impedance.149090 Maximum non zero size exceeded.151001 The minimum number of newton steps is larger than the maximum number of newton steps.152001 Unable to create the solved device file.152002 P adaption cannot proceed because the maximum polynomial order hasalready been reached.152003 An error occurred outside an Infolytica library. The exact source of the error is not known.152004 to 152008 An error occurred during the error recover process for adaption. The adaption process was aborted. However, there may be a valid solution if one or more adaption steps had already completed successfully.152010 The 3D solution mesh generation failed.152011 The maximum number of component faces in the 3D solver has beenexceeded.152013 There is no magnetic solution to reuse. Change the magnetic solve option in the Coupling Options dialog.152015 The magnetic problem time interval overlaps the thermal problem time step. 152032 There is a hole in a face with a non-uniform voltage distribution assigned to one of its edges.152033 An edge with a non-uniform voltage distribution is not in any electrode. 152034 An edge with a non-uniform voltage distribution has zero length.152035 A face of an electrode has more than two edges with a non-uniform voltage distribution.152036 A face of an electrode has two adjacent edges with a non-uniform voltagedistribution.152037 An edge with a non-uniform voltage distribution shares a node with more than four faces.152038 Not all edges of a face of an electrode containing edges with a non-uniform voltage distribution were found in the mesh.152039 An edge with a non-uniform voltage distribution was not found in the mesh.154001 No initial mesh.154002 Mesh has no tetrahedra.154003 Mesh link to device failed.154004 Unable to repair degenerate tetrahedra. For transient with motion solutions, refining the mesh of the remesh region should fix the problem.154005 Non-coil components missing in material mesh.154006 Tetmesherror.154007 Simmetrixmesherfailed.154008 No license for Meshing Method.154009 Conflict between periodic and user-defined boundary conditions.154010 Periodic boundary condition inconsistency.154011 Unable to subdivide prism into tetrahedra.154012 Unable to generate base extrusion mesh.154013 Mesh has duplicate nodes.154014 Tet nodes are not unique.See also Error recovery Error recovery: out of memory 154015Mesh contains unreferenced nodes.154016Inconsistent mesh topology.154017Mesh is inconsistent with model.154021The SolverAbortAfterMeshing parameter was set to Yes (3D only). 154024No conducting path between terminals in the material mesh.154025No conducting path was found between coil terminals (perhaps because no terminal faces or coil components were found in the material mesh). 154026A coil terminal is in direct contact with another terminal and/or a flux tangential boundary condition (the terminals are shorted).154027A single tetrahedral element contains both a binary master and binary slave constraint. 154028The mesh between coil terminals is too coarse. Refine the mesh in the coil component. 154029A coil that uses a coil mesh has the StrandArea parameter set. 154030 Mismatched nodes on mesh faces found. Refining the mesh on the faces ofperiodic boundary conditions and/or re-mesh regions should fix the problem.Refer to the MeshLog.txt for details.155001 An error occured while trying to generate the ACIS model.155002 An error occured while trying to generate the ACIS model.155008 A non-manifold geometric component was detected while trying to generate themodel.157001 Motion component position is not computable.157002 Motion component is inconsistent with bodies determined in force and torquecalculations.157003 Motion solver failed to converge.157004 Motion component position has exceeded preset limits.157005Magnetic solver calculated an invalid force.157006 Cannot open the log file (e.g., MotionLog.txt may be locked by anotherapplication such as Excel or Word).157007 Mass is zero.158000 to158004An error occurred during the error recover process for adaption. The adaption process was aborted. However, there may be a valid solution if one or more adaption steps had already completed successfully.159000 to159001An error occurred during the error recover process for adaption. The adaption process was aborted. However, there may be a valid solution if one or more adaption steps had already completed successfully.160001 An error occurred during the error recover process for adaption. The adaptionprocess was aborted. However, there may be a valid solution if one or moreadaption steps had already completed successfully.163000 Failed to build non-linear BH curve.163001Failed to build non-linear loss curve.。