Win Pak Document

System ManagerThe System Manager is a utility in WIN-PAK to locate its various software components. The machine name and protocol end point for each program component is displayed in the System Manager. Honeywell recommends you to retain the default settings.This topic includes information about:∙Setting RPC Endpoints∙Setting User Interface Workstation∙Setting Domain/Workgroup Environment∙Setting Server LocationSet User Interface WorkstationEnsure that you quit the WIN-PAK User Interface, before setting the User Interface workstation.To set the user interface workstation,1.Choose Start > Programs > Honeywell Access Systems > WIN-PAK SystemManager. The System Manager window appears.2.Click the User Interface tab.3.Click Add. The System Manager - Servers Setup dialog box appears.4.Enter a descriptive Name to identify the database server from the list.5.Enter the computer name or IP address of the server in the Node Name field in theDatabase Server area.Ensure that the RPC Endpoint is the same as the value you set in Setting RPCEndpoints.6.Under Database Archive, type the computer name or IP address of the server in theNode Name field.Ensure that the RPC Endpoint is the same as the value you set in Setting RPCEndpoints.7.Click OK. This enables you to start up the User Interface with the new databaseserver.Set Domain/WorkGroup EnvironmentTo work in a Workgroup Environment, you must set the workgroup environment and then unblock the WIN-PAK services from Firewall protection.To set the domain/workgroup environment:1.Click Start > Programs > Honeywell Access Systems > System Manager. TheSystem Manager window appears.2.Click the RPC Security Options tab.3.Under Client-Server Communication Settings,select WORKGROUP EnvironmentORSelect DOMAIN Environment (Recommended) and click OK. The selectedenvironment isSet Server LocationNote:These steps can be used to set the location for the following servers:o Communication Servero Command File Servero Guard Tour Servero Muster Servero Schedule Server1.Click Start > Programs > Honeywell Access Systems > WIN-PAK SystemManager. The System Manager window appears.2.Click the appropriate server tab.3.Type the DB Server Node Name. This is the location for the Database Server.4.Type the DB Server Endpoint value.5.Click OK to save the changes.Note:For the Schedule Server, set the value for the Report Connection Timeout. Firewall Exception SettingsThe Windows Firewall protection system blocks the WIN-PAK services in a networked system. Therefore, you must unblock the WIN-PAK services before using WIN-PAK.This topic includes:∙Unblocking WIN-PAK Services on Windows XP SP2∙Disabling Firewall in Windows 2003 Server∙Enabling Ports in Windows XPEnable Ports in Windows XPCommunication ports in a Windows XP operating system are disabled for security reasons by Windows Firewall. These ports must be enabled for remote communication to the Galaxy panel.To enable ports in the Windows Firewall:1.Click Start > Settings > Control Panel and open Windows Firewall. The WindowsFirewall dialog box appears.2.Click the Exceptions tab and click Add Port. The Add a Port dialog box appears.3.Type the Name of the port and the Port Number.4.Click TCP or UDP to select the type of port.5.Click OK to open the port.Note:∙Repeat the above procedure for enabling three ports in the system, where one port is used by Galaxy Gold and the remaining two ports are used bythe Galaxy panel for reporting alarms and control commands.∙In the same way, the 3001 or 2101 ports must be enabled for the TCP/IP communication of the access panels.System SettingsThis chapter describes how to configure WIN-PAK users and to set the default settings for WIN-PAK.AccountsThis section Accounts describes to add, edit and delete an account. The card and card holder information in WIN-PAK are specific to an account. Therefore, you must select an account to enable card and card holder menu options.WIN-PAK UsersThis section WIN-PAK Users describes in detail about configuring the users and assigning privileges to them.Users of WIN-PAK are of two types, namely, Administrators and Operators. An administrator has full privileges (view, change, and delete) to work in WIN-PAK whereas, an operator has restricted privileges, which are defined by the associated operator levels.When you install WIN-PAK on your computer, a default user is created for logging on to WIN-PAK with administrator privileges. The default user name is admin with a blank password. However, to ensure security, you can change the user name and password.Default SettingsThis section describes how to change the default settings for WIN-PAK workstation and system settings. Defaults can be changed for alarm printer, sound files, e-mails for reporting alarms, auto log on, and so on.In the WIN-PAK system, these settings are configured by default and WIN-PAK functions as per these settings. All the client systems of WIN-PAK would be affected by any changes made to the System Defaults settings. Whereas, only the computer where the settings are changed are affected by the Workstation Defaults settings.This topic covers information about:∙Accounts∙Operator Levels∙Operators∙Workstation Defaults∙System Defaults。