青书卡安装说明

合集下载

智能非接触读卡器安装说明书

智能非接触读卡器安装说明书安装方式1将铝合金金属板用2个或者4个螺丝固定在墙上或者安装盒上 .2将读卡器上面卡扣挂上铝合金金属板 , 再将读卡器下端按下 ●. 3将读卡器下端的防脱螺丝拧紧 ❍. 安装完成.规格说明建议采用线性直流电源22AWG 屏蔽线缆; 一端接地(如下图)物理尺寸图读卡器的启动读卡器上电，绿色LED 闪亮5次，蓝色LED 亮起；蜂鸣器蜂鸣1声，读卡器进入工作状态。

刷卡，蓝色LED 闪亮一次；蜂鸣器蜂鸣一次。

按键读卡器时, 按键盘一次，蓝色LED 闪亮一次；蜂鸣器蜂鸣一声。

接线方式故障排除Keypad & Proximity Flash Mount Reader Installation ManualMounting:1.Install the metal plate on the wall with two or four screws, which dependson different kinds of gang box being installed .2.The cover shall clip on the upper edge the push in the bottom part asshow in diagram●.3.Tighten the secure non-dropout screw, which located underneath of thereader to fix the reader and the back plate❍, installation is completed.Recommendation:1.Linear DC Power Supply;2. 22AWG shielded cable; it’s required to do “one-point” ground. (As shown in the diagram)Power up Sequences:1.When reader is powered up, the Green back will flicker for 5 seconds. The reader will beep once and thereader is in Ready mode.2.Present the card. The Blue LED will flicker once; buzzer will beep once.3.When card is present and read by the reader, blue back lit will flash once; and buzzer will beep once aswell. The card data will then transmit to the controller. After, weather the back lit of the reader will remain ON or Flash or change to Green or Red color, this shall depend on the Green and Red LED inputs Wiring:Troubleshooting:。

移动图书馆在安卓系统的安装使用

超星移动图书馆在安卓系统上的安装使用一、设置借阅证密码各位师生的借阅证初始密码为空，需要在我校图书馆网站修改（设置）新密码后，方可使用移动图书馆。

在图书馆网站的左下方有【读者登录】按钮，点击进入读者登录页面，或者直接从此链接http://192.168.2.21/fsweb/Default.aspx进入读者登录页面。

【用户名】栏中输入您的借阅证号（注意大小写），如果以前未设置过密码，则【密码】栏不用填，直接点击【登录】按钮。

登录后点击上方的【读者管理】页面，然后点击【修改密码】，打开修改密码页，如果从未设置过密码，则密码为空，【原密码】栏不用输入，输入两次新密码，然后点击【确认并修改】按钮。

修改完成后，请退出登录，用新密码重新登录一次，以确认密码修改（设置）成功。

二、手机客户端下载安装手机客户端下载有两种方法，这里介绍第一种，在超星网站下载客户端。

在本文最后的附录中，介绍从软件市场下载客户端的方法。

在手机上用浏览器访问，在页面上方可以看到提示【使用客户端您将获得最佳体验】。

点击这行提示文字就开始下载客户端，将其安装到手机上，安装后的软件名称为“移动图书馆”。

三、手机客户端登录在手机上打开【移动图书馆】软件，在首页面点击左上角的人像图标打开个人菜单，菜单上方显示【尚未登录】。

点击这行字打开地区选择页面，选择【河南省】，在下级页面里选择【南阳医学高等专科学校】，进入个人登录界面。

输入您的借阅证号和密码后点【提交】，会弹出一个“完善用户信息”窗口。

在完善用户信息窗口输入您的手机号和电子邮箱（请填写常用邮箱，这会作为【您的注册邮箱】，以后有用），然后点击【确定】，就完成了个人登录操作。

四、移动图书馆的使用登录后您就可以使用超星移动图书馆的资源了。

软件初始有七个资源栏目，您也可以点击【添加订阅】来添加新的资源。

这里对常用功能作简单介绍。

1、使用【个人书架】点击【书架】可以打开个人书架。

书架的初始状态是空的，点击【添加】按钮来给书架添加图书。

23--PRO22R2（双读卡器模块）安装说明书

23--PRO22R2（双读卡器模块）安装说明书PRO-2200双读卡器模块安装手册（PRO22R2）目录警告及提示 (1)声明 (2)拆包装程序 (2)运输指导 (3)保修期 (3)保密性 (3)描述 (3)设置 (4)LED 指示灯 (5)电源 (5)通信 (6)读卡器连线 (6)报警输入连线 (7)控制输出连线 (7)安装说明 (8)推荐安装步骤 (8)参数总录 (9)警告及提示警告安装前，请断开所有外部供电电源。

在给设备上电前，请确认电源的供电电压在设备要求的电压范围内。

在设备未安装完毕前，不要给系统上电。

请勿必遵守此警告，否则可能会造成人身伤亡和设备损坏。

警告消防及安全性提示在使用读卡器的关键出入口、消防通道、栏杆、电梯等，根据消防和安全条例的要求，必须安装有其他的应急出口。

这些防火和安全条例各地不尽相同，所以采用电子设备控制门或其他通道系统时，必须取得当地消防机构的认可。

例如，使用出门按钮，在某些地区，可能是不可法的。

在许多应用场所，出门指示要清晰明了，一看就懂，容易使用，而不需要事前告知，这是安全条例的要求。

所有的许/认可要以书面方式确认。

不要接受口头的认可，口头认可不具有法律效律。

Engineered Systems不建议使用PRO2200 或相关产品作为主要的报警监控系统。

主要的报警监控系统应该符合当地消防和安全条例的要求。

安装商必须定期对系统进行测试，并指导最终用户进行适当的日常测试。

不做定期的测试维护，当最终用户出现使用问题时，安装商应对造成的损失负有责任。

警告所有外箱必须正确接地。

警告所有电锁需做电磁保护，可安装S-4。

Engineered Systems建议用户选用使用直流供电的电锁。

本手册可以在未通知的情况下进行更改。

提醒若运输过程中造成损坏，请在索赔中填写承运商。

提醒静电可损坏CMOS集成电路和模块。

为防止静电破坏需遵循以下操作：在运送所有电子设备，包括已安装的读卡器，使用防静电所装袋或防静电容器。

大学生心理测验及档案管理系统普及网络版安装说明

大学生心理测验及档案管理系统普及网络版安装说明————————————————————————————————作者：————————————————————————————————日期：大学生心理测验及档案管理系统普及版安装说明一、安装概要说明大学生心理测验及档案管理系统普及版,是一套集测试、统计、报告、预警、预约、咨询等功能于一体的心理管理系统。

本软件采用的B/S结构，前台开发工具为 2005，后台数据库采用Microsoft SQL SERVER 2000大型数据库，运行时建议采用的显示分辨率为"1024×768 小字体"。

二、软硬件环境（1）服务器端推荐配置●CPU:P4 2。

6G及以上●内存:1G及以上●硬盘:80G及以上、系统盘有10G以上的可用空间●操作系统：Windows 2000 Server 简体中文版或2003 Server●必须已安装IIS-—Internet信息服务●必须已安装SQL SERVER2000，且SQL SERVER的服务已启动●浏览器升至IE6.0版本(2）客户端推荐配置●CPU：P3 1GHZ及以上●内存：256M及以上●硬盘:40G及以上●操作系统：Windows 2000 /98/xp 简体中文版（推荐使用windows xp系统)●浏览器最好是IE6.0版本，但不可低于IE5。

0版本三、软件安装第一步：安装IIS✧该步骤对于已安装了IIS服务的用户,可以省去。

一、WINDOWS 2000 SERVER系统下安装IIS1、点击开始→设置→控制面板→添加/删除程序，弹出添加/删除程序选择界面；2、点击选择“添加/删除组件”出现以下windows组件安装界面，如图1；3、勾选组件--Internet信息服务（IIS）,点击“下一步(N)"开始安装IIS。

4、直至IIS安装完全。

图1二、WINDOWS 2003 SERVER系统下安装IIS1、点击开始→设置→控制面板→添加/删除程序，弹出添加/删除程序选择界面；2、点击选择“添加/删除组件”出现以下windows组件安装界面，如图2；图23、勾选组件-—应用程序服务器，点击“详细信息(D）”出现应用程序服务器安装列表，如图3：图34、分别勾选“”“Internet信息服务（IIS)"“启用网络COM+访问”“应用程序服务器控制台"四个子组件，点击“确定”,返回上一级菜单，点击“下一步（N）”开始安装.5、直至IIS安装完全。

Scale Link 2000 Series安装指南说明书

Scale Link 2000 Series Installation ManualTopcon Agriculture AmericasW5527 Hwy 106Fort Atkinson, WI 53538USATel: 800-225-7695E-mail:*******************D4197-EN SL2 Series Installation Manual LCCAll rights reserved. Reproduction of any part of this manual in any form whatsoever without Topcon Agriculture Americas express written permission is forbidden. The contents of this manual are subject to change without notice. All efforts have been made to assure the accuracy of the contents of this manual. However, should any errors be detected, Topcon Agriculture Americas would greatly appreciate being informed of these errors. The above notwithstanding, Topcon Agriculture Americas can assume no responsibility for errors© Copyright! 2017 Topcon Agriculture Americas, Fort Atkinson (U.S.A.).Table of Contents1.0 INTRODUCTION (4)2.0 TECHNICAL SPECIFICATIONS (5)3.0 SAFETY DURING USE (6)3.1 Exposure to Radio Frequency (6)3.2 Prior to Operation (6)3.3 Check System Before Use (6)3.4 Cleaning (6)3.5 Battery Charging and Welding (6)4.0 OVERVIEW SCALE LINK ISOBUS SYSTEM (7)5.0 FEATURES (8)6.0 CONNECTOR TYPES AND FUNCTION (10)6.1 Connector PINOUTS (11)7.0 MOUNTING (12)8.0 LOAD CELL CONNECTIONS (13)8.1 Load Cell Setup and Connections (13)9.0 DISPLAY (13)10.0 WIRING REFERENCE INFORMATION (14)11.0 (SLC) SCALE LINK CONTROL CONNECTION & SERIAL CONNECTION (15)12.0 OPTIONAL EQUIPMENT (16)Introduction1.0 INTRODUCTIONThank you for purchasing a Scale Link TM product.This installation manual describes the steps necessary to install the Scale Link TM and available connector configurations.Scale Link TM works with several types of user displays such as Scale Link Control (SLC2810, SLC2400) TM, Universal Terminal (ISO models ONLY), and the Touch Screen Terminal (TST7600) Feed Mixing system. Separate manuals describe the use and installation of the displays.Additional Document Information listed below;D4196 - SL2 ISO Operat or’s ManualD4195 –SLC 2810 Operator’s ManualD4020 - Direct Access Numbers (D. A. N.)D4204 - SL2 Technical ManualTechnical Specifications 2.0 TECHNICAL SPECIFICATIONSSafety During Use 3.0 SAFETY DURING USEDanger: Indicates an imminently hazardous situation that, if not avoided, WILL result in death or very serious injury.Warning: Indicates a potential hazardous situation that, if not avoided, CAN result in death or very serious injury.Caution: Indicates a potential hazardous situation that, if not avoided, MAY result in a minor injury.IMPORTANT !: Signals special mechanical information3.1 Exposure to Radio FrequencyExposure to energy from radio frequencies is an important safety issue. As this product uses the Wi-Fi and Cellular system of a smartphone or tables please consult with the safety information provided with the device that the App operates with.3.2 Prior to OperationRead and understand this manual and learn all controls before you use the equipment. Check that the area is clear of people, animals, and obstacles before starting any work. Identify possible hazards.3.3 Check System Before UseBefore using the App with the Digi-Star weighing system read the Operator’s Manual for the scale indicator and the Wi-Fi system. Follow all instructions.IMPORTANT!3.4 CleaningDo not use pressurized running water (high pressure cleaners, hoses nozzles, etc.) to clean the indicator. Water ingress and damage to the indicator may result. Use soapy water and a sponge or cloth for best results.3.5 Battery Charging and WeldingDisconnect all cables from the ScaleLink2 system before charging the battery or welding on the machine. If cables are left connected, indicator damage may result.Overview Scale Link ISOBUS System 4.0 OVERVIEW SCALE LINK ISOBUS SYSTEM5.0 FEATURESSL21xx SERIES SCALE LINK FEATURES14672351. Communications:(printer, touch screen, other serial enabled devices).2. ISOBUS connections (CAN1)3. Power 11 to 36VDC4. SLC / Remote Connection5. ISOBUS Connections (CAN2)6. Reset Button7. USB8. Load Cell Connections9. Remote Output (Terminal OP1)89FeaturesSL22xx SERIES SCALE LINK FEATURES11. Scale Link 2 load cell terminal board6.0 CONNECTOR TYPES AND FUNCTIONSeveral connectors types are utilized as standard or optional equipment on the Scale Link. Find below detailed information on the connectors.Find detailed PINOUT information for commonly utilized connectors noted above on the following page.CappedUn-CappedConnector Types and Function6.1 Connector PINOUTSMounting7.0 MOUNTINGUsing the washers supplied with this product, mount the Scale Link as shown in Option 1 or Option 2. (Remove top cover from scale link to install mounting screws).ORMount Scale Link 2 using adhesive tape. Place adhesive tape on back side of Scale Link (Option 3)Option 1. Directly to Implement Option 2. Bracket (p/n: 408283)Placement of two5” strips of VHBtape on the back ofSL2 housingbottom.Option 3. Adhesive tape8.0 LOAD CELL CONNECTIONSIMPORTANT ! If connecting Scale Link to a different brand of load cells, color schemes and functions may not match.8.1 Load Cell Setup and ConnectionsIf you have;∙ M12-5P connectors on the Scale Link and Load Cells: Plug Load Cells directly in to Scale Link 2 connections.∙ No Load Cell connectors on Scale Link and bare leads on Load Cells: Install cables through strain reliefs connectors and wire Load Cells to Scale Link terminal blocks LC1 thru LC4.9.0 DISPLAYDetermine which connector is used with your display. See connector options on pg 10. Connect display to mating connector on Scale Link. Refer to wiring referenceinformation shown on pages 14 and 15 for more detail. Connect Scale Link to a 11.0 to 36.0VDC power source.WIRE LOAD CELLS DIRECTWIREMAIN PCB DESIGNATORFUNCTIONRED RED +SIGNAL GREEN GRN -SIGNAL WHITE WHT +EXCITATION BLACK BLK -EXCITATION SHIELDSHDSHIELD EZMATE CONNECTORSWIREMAIN PCB DESIGNATORFUNCTIONBROWN RED +SIGNAL WHITE GRN -SIGNAL BLUE WHT +EXCITATION BLACK BLK -EXCITATION GRAY SHDSHIELD Load Cell ConnectionsWiring Reference Information10.0 WIRING REFERENCE INFORMATIONSee Section 5.011.0 (SLC) SCALE LINK CONTROL CONNECTION & SERIAL CONNECTION∙SLC2810, SLC2400 indicators will connect to M12-8 labeled SLC located on Scale Link Unit.∙Wi-Fi Module (using cable with p/n:410818) will connect to M12-8 labeled SERIAL located on Scale Link Unit.SerialConnectionfor Wi-FiModule. SLC Connection & Serial ConnectionOptional Equipment 12.0 OPTIONAL EQUIPMENT409665 Radio-ERM-WIFI ExternalWiFi Radio Module for use tocommunicate with Android or IOSphone or tablet and Topcon Ag ControlApps. Requires Cable Below.410818 Cable-M12 SER to ERM (13’or 4m) Adaptor Cable to connect ERM-WiFi to SL2. Cable length allowsERM-WiFi to be placed in a positionhigh on the machine to provide clearLine-of Site communication.。

CU-DK402使用手册

使用手册安装使用前请仔细阅读本说明书目录一、引言二、产品外观三、系统功能四、主要参数五、安装接线六、故障检修七、原装附件八、软件安装九、门禁软件十、考勤软件一、引言：感谢您使用本网络(联网)型门禁系统，在使用本系统之前，请您详细阅读本使用手册，并严格按照手册中的要求来操作。

此手册将介绍本系统主要功能及操作使用方法。

本门禁系统采用目前世界上先进的技术-非接触式感应卡技术（也称射频识别卡（RFID）技术，RFID卡具有全球卡号唯一、不易仿制的读写特性和安全性能。

RFID卡片不会产生使用磁卡时因磁头磨损、磁粉脱落、灰尘等影响所带来的麻烦，而且避免了接触式IC卡因芯片与读卡器外露而引起的沾污、接触不良和外物损伤而导致的读卡不良现象，RFID卡适应各种环境，经久耐用。

每一次感应卡读的信息，无论是否向电锁发出开锁指令，系统都自动记录下来，管理者可以通过计算机下载调阅门禁控制系统存储的信息资料，轻松查阅、打印所有的通行事件。

管理软件将根据此原始资料自动统计员工考勤情况、编制考勤报表；还可提供在线式巡更系统！本系统提供了一种智能化的出入口控制、考勤管理及在线式巡更，适用于需要控制人员出入的通道、智能化生活小区、商务机构、政府机关以及考勤管理人员较多的企事业单位。

二、产品外观：1、主机及门控器外形图2、主机指示灯三、系统功能：1、名词解释：事件记录：是指每一次控制器发生动作时所有的记录，包括事件发生时间、地点、人员、事件类型事件类型：主要包括用户读卡进门、读卡出门、主用户卡读卡进门、主用户卡读卡出门、非法卡、按钮开门、报警、密码开门、禁行时段不开、节假日管制不开、管理时段不开、反潜回不开、反尾随不开、紧急时段不开。

卡类型：包括主用户卡、胁迫卡、管理卡、用户卡、访客卡。

主用户卡是指不受通行时段、管理时段、节假日、反潜回控制的卡；胁迫卡是指拥有主用卡的功能，但在读卡时会启动输出报警信号；用户卡是指可根据需要设置禁行时段、节假日管制、管理卡首开时段等控制手段；管理卡是指权限和用户卡一样，但是管理卡首开时段必须先读此类卡后其他用户卡才有效；访客卡权限和用户一样，但是多了一个时效限制。

书生安装操作手册

一、Reader的安装双击“我的电脑〉－光盘驱动器>单独reader>SursenReader72Setup。

exe"弹出画面如图:单击“是”，进行安装，出现如下画面，如图:执行安装文件系统初始化安装单击“下一步”，出现“许可证协议”对话框,如图：选择“我接受该许可证协议中的条款”，单击“下一步”，如图：安装文件夹默认为C：\Program Files\sursen，可根据情况改变目标文件夹路径，单击“下一步”按钮，如图：需要重新选择安装路径单击“上一步”,不需要请单击“下一步”，默认的安装类型为“完整安装”，弹出如下图：若需重新进行设置单击“上一步”，不需要请单击“安装",弹出如下图：安装完成后系统弹出页面，如图:单击“完成”，Reader程序安装结束。

二、Reader的使用说明1、Reader 7.2界面介绍单击“开始"―“程序”―找到“Sursen Reader7.2”程序项，单击即可打开Sursen Reader7.2，屏幕将显示Sursen Reader7.2的主窗口,如图所示，它包括主菜单、工具条和信息显示区,其中“工具"中的“设置"为高级设置选项.如下图所示:界面介绍：从上至下依次为:●标题行：Reader 7.2标志.●菜单栏：Reader 7。

2可操作的各个菜单项，不同的菜单项有不同的功能。

●工具栏:Reader 7。

2里常用到的一些工具,其中包括打开、保存、打印、适度显示、页面大小调整、翻页等工具。

●公章快捷工具栏:在这里可以进行公章定位、验证以及对sep文件进行盖章等操作。

显示区域：这个区域显示被选择打开的sep、s2、s72、ps2、s92、GW、GD 文件以及书生网上的电子书籍。

2、Reader 7.2使用指南文件菜单文件菜单可以实现文件的打开、保存、打印及退出等操作.◇打开：要打开一个文件有以下三种方式：（1)双击Reader 7.2支持的文件格式，直接打开。

浩顺一卡通软件说明书

一、系统简介 (7)二、系统组成 (7)三、系统安装卸载 (7)1. 软件安装步骤 (7)2. 软件卸载 (9)3. 数据库的安装 (9)四、建立浩顺一卡通帐套 (17)五、软件登录 (19)六、操作说明 (20)1、系统管理 (20)(1)、系统权限 (20)(2)、机器操作员 (22)(3)、系统选项 (22)(4)、自动服务 (24)(5)、修改用户密码 (25)(6)、软件注册 (25)2、人员资料管理 (25)(1)、卡级别设置 (25)(2)、充值赠送设置 (26)(3)、部门资料设置 (27)(4)、人员卡片管理 (28)(5)、人员统计表 (30)(6)、卡片操作明细表 (31)3、考勤管理 (32)(1)、感应考勤机管理 (32)(2)、感应考勤机参数 (32)(3)、感应考勤机卡片注册 (33)(4)、感应考勤机消息注册 (33)(5)、感应考勤机数据回收 (34)(6)、感应考勤机实时监控 (34)(7)、人脸考勤机 (34)(8)、请假类型设置 (34)(9)、出差类型设置 (35)(10)、加班类型设置 (35)(11)、周休日方案 (35)(12)、节假日方案 (36)(13)、基础班次建立 (36)(14)、排班规律建立 (37)(15)、个人工作方式 (38)(16)、部门工作方式 (38)(17)、个人排班表建立 (39)(18)、部门排班表建立 (40)(19)、排班表维护 (40)(20)、班包建立（模糊排班） (41)(21)、顺序计时班建立 (41)(23)、出差单 (42)(24)、加班单 (43)(25)、手工签卡 (43)(26)、考勤数据分析 (44)(27)、考勤异常处理 (44)(28)、考勤原始记录表 (45)(29)、考勤刷卡记录表 (45)(30)、考勤日报表 (46)(31)、考勤月报表 (46)(32)、考勤统计表 (47)4、门禁管理 (47)(1)、门禁机管理 (47)(2)、门禁机假日管理 (48)(3)、门禁机时段管理 (48)(4)、门禁机权限分配 (49)(5)、门禁机数据回收 (49)(6)、门禁机实时监控 (50)(7)、电子地图 (50)(8)、门禁出入记录 (51)(9)、报警事件记录 (51)(10)、开门密码管理 (52)(11)、远程开门 (52)(13)、多门互锁 (53)(14)、反潜回 (54)(15)、多卡认证 (55)(16)、首卡开门 (55)(17)、内外刷卡确认 (56)(18)、定时开门 (57)(19)、报警及消防联动 (57)5、收费管理 (58)(1)、场所设置 (58)(2)、小票打印设置 (58)(3)、品种设置 (59)(4)、收费机管理 (59)(5)、收费机参数 (60)(6)、收费机数据回收 (64)(7)、收费机实时监控 (65)(8)、账户充值 (66)(9)、账户取款 (66)(10)、账户充值取款 (67)(11)、软件消费 (67)(12)、补贴管理 (68)(13)、补贴清零 (69)(14)、报表结账处理 (69)(16)、查询最近余额 (70)(17)、订餐明细 (71)(18)、订餐统计 (71)(19)、卡片消费明细 (72)(20)、卡片消费统计 (72)(21)、品种消费明细 (73)(22)、品种消费统计 (73)(23)、卡片充值明细 (74)(24)、卡片充值统计 (74)(25)、卡片取款明细 (75)(26)、卡片取款统计 (75)(27)、分餐日统计 (76)(28)、营业消费统计 (76)(29)、消费综合统计 (77)(30)、消费数据总表 (77)6、水控管理 (78)(1)、水控充值 (78)(2)、水控批量充值 (78)(3)、水控取款 (79)(4)、水控数据卡制作 (79)(5)、水控卡片明细表 (80)(6)、水控卡片统计表 (81)一、系统简介现代企业分工愈来愈精细、竞争愈来愈激烈，各企业都想尽办法在管理上要效益，而员工考勤烦琐复杂，企业要投入较多的人力、物力、时间，购买打卡钟、打卡、统计，结果费事费力还经常出错.员工考勤成了企业发展的烦恼。

正式考试客户端安装说明

正式考试客户端安装说明
2017-05-02
如果计算机上安装过以前的考试版本（参加过模拟考试）而且还没有卸载，那么可以在清理D:盘文件夹(D:\GUOGUOKAO、D:\GUOGUOKAOT、D:\CZKT)后使用绿色升级包。

如果以前未安装过或者已经卸载，则必须使用完全安装包进行安装。

云练习客户端，直接删除其安装目录D:\GUOGUOKAO即可。

一、绿色安装
已经安装模拟考试客户端而且还没有卸载模拟考试客户端的的考试机，才能使用绿色升级包。

升级不涉及C:盘，因此C:可以保持写保护。

1、在考试网站上下载绿色绿色升级包。

2、将以前安装路径D:\guoguokaoT（以前默认安装）手动删除。

3、使用下载的绿色安装客户端直接解压，默认安装就可以。

二、使用安装包安装
所有考试机，如果没有安装过模拟考试客户端或者安装过但已卸载，则必须使用完全安装包来安装正式考试客户端。

安装前必须解除C:盘写保护，安装完毕可以将C:盘启用写保护。

1、首先在考试网站下载最新的考试系统安装文件。

2、卸载以前计算机上安装的考试客户端。

3、手动删除以前安装路径D:\guoguokaoT（以前默认安装位置）。

4、使用下载的最新的安装包全新安装即可。

注意：考试系统客户端的安装磁盘必须要停止写保护，操作系统盘可以进行保护。

如果是第一次安装，首先停止操作系统盘的写保护，安装完成以后可以继续保护系统盘。

万普校园卡软件-使用说明(万普软件)

万普校园卡软件使用说明( 2012版)广州万普软件技术有限公司出品目录一、软件简介 (3)二、安装和卸载 (3)三、启动和运行 (4)四、学校管理功能 (5)(一) 学校设置 (5)(二) 年级管理 (5)(三) 班级管理 (6)(四) 学生管理 (6)(五) 教师管理 (8)(六) 时间设置 (10)(七) 学校通知 (10)五、校园卡管理功能 (11)(一) 校园卡管理 (11)(二) 发卡 (12)(三) 销卡 (12)六、运行管理功能 (13)(一) 播放音乐 (13)(二) 开始刷卡 (14)七、出入校管理 (15)(一) 迟到情况查询 (15)(二) 历史数据查询 (15)(三) 图形分析 (16)八、短信发送功能 (16)(一) 发送短信 (16)(二) 批量发送 (17)(三) 短信模板 (18)(四) 发送记录 (18)(五) 发送设置 (19)九、系统管理功能 (19)(一) 用户管理 (19)(二) 权限设置 (20)(三) 日志查询 (20)(四) 数据清理 (21)一、软件简介万普校园卡软件是专门用于学校校园卡管理的信息化系统，具有功能实用、操作简单的特点，适用于幼儿园、中小学、职校等各类学校。

可以配套使用市场上广泛使用的各类校园卡，支持磁卡、条码卡、RFID无源低、中频感应卡，RFID有源高频感应卡等；并可使用第3方的短信发送网关或者独立的短信猫等短信发送设备。

二、安装和卸载如果您是使用光盘安装，在插入安装光盘后，会自动运行软件的安装向导程序（在windows设置了禁用光盘自动运行后此程序在光盘插入时不自动运行，您可打开光盘根目录，双击wpautorun.exe），如下图：您可选择安装单机版本或安装网络版本的服务器和客户端。

在安装单机版和服务器之前，请确保电脑中已经安装了SQLServer数据库系统，如果没有，您可以首先安装免费的SQLServer桌面版。

卸载软件，可以打开windows的控制面板¡〉程序和功能，选择¡万普校园通软件¡，卸载即可。

Duokan 2012 for Kindle 4 安装指南修订版

多看2012 for Kindle 4安装指南（适用于非触摸屏版本）安装器版本：DuokanTool ver 1.1.0118 build 5116文档日期：2012.02.23 修订版文档作者：多看开发组报告建议：多看论坛/修订历史：2012.02.23 补充FAQ 82012.02.22 修改部分插图和诊断模式文字说明2012.02.08 补充步骤4的文字说明, 添加FAQ2012.01.20 修改部分图片, 添加步骤4.42012.01.13 初始版本说明：《安装指南》仅适用于Windows版的安装器。

第一次安装Duokan for Kindle 4，务必通读《安装指南》，先有个总体印象，然后按照具体步骤安装。

如有疑问，请看文档最后几页附录FAQ找到解答。

正文：安装步骤（Step by Step）1.用纸或者其他工具记下kindle的序列号：1.1.按键Home键，进入kindle主页面；1.2.按键Menu 选择Settings，翻到第2页Device Info；1.3.记录Serial Number如下图所示。

注意: 序列号的0（零）不要记错为O（欧）。

2.拷贝安装文件：B线连接kindle到PC，找到kindle磁盘。

2.2.复制DK_System文件夹和ENABLE_DIAGS到kindle的磁盘根目录。

ENABLE_DIAGS是一个0字节文件。

3.断开USB连接，重启kindle，步骤如下图所示：按键Menu -> 选择Settings -> 再次按键Menu ->选择Restart4.kindle进入诊断模式并打开USB-network：在启动过程中，将出现诊断模式特有的“斜条纹”画面。

然后白屏，再然后系统显示System Diags菜单。

4.1.选择N) Misc individual diagnostics；4.2.选择U) Utilities；4.3.选择Z) Enable USBnet。

OK系列图像卡硬件安装手册说明书

OK系列图像卡硬件安装手册User Guide for OK Series Frame Grabber(便携/嵌入/数字/线阵图像卡)二零一九年五月版北京嘉恒中自图像技术有限公司Beijing JoinHope Image Technology Co., Ltd .目录第1章快速使用 (1)1、系统要求 (1)2、产品清单 (1)3、硬件安装 (2)4、程序安装 (3)5、图像卡测试 (4)6、常见问题 (5)第2章性能与规范 (8)1、OK系列图像卡简介 (8)2、图像卡输入输出插座连线定义 (10)第3章便携/嵌入式系列 (13)1、OK_PC10A、OK_PC20A (13)2、OK_PC21B (15)3、OK_PR10B、OK_PR20B、OK_PR30A、OK_PR30B (17)4、OK_PM10A、OK_PM10B、OK_PM20A、OK_PM20B (20)5、OK_USB20A (21)6、OK_USB30B (23)7、OK_CPC16A (24)8、OK_CPC12A (25)9、OK_CPC41D (26)10、OK_CPC43C (27)11、OK_CPC60C (28)12、OK_CPC61E (29)第4章数字系列 (30)1、OK_CL20A、OK_CL40A、OK_CL60A (30)2、OK_CL20B、OK_CL40B、OK_CL60B (34)3、OK_LV20A、OK_LV40A、OK_LV60A (35)4、OK_LV20B、OK_LV40B（-E）、OK_LV60B (39)5、OK_LV50A-E (40)第5章线阵系列 (41)1，OK_LS100A、OK_LS120A (41)2第6章其它功能卡 (42)第7章软件安装与使用 (47)1，设备登记与设备驱动安装 (47)2，开发库与演示程序安装 (47)3，撤除图像卡的安装 (50)4，撤除驱动与演示程序 (50)5，OK设备管理器的使用 (50)6，图像卡测试 (53)前言北京嘉恒中自图像技术有限公司是国内领先的数字图像产品供应商，总部位于中关村中科院自动化研究所，是一家聚集了大批业内技术精英，以自主研发为核心竞争力的股份制高新技术企业。

Intermec EasyCoder 字体卡安装指南说明书

• EasyCoder PF2i, PF4i, PF4ci, and PM4i printers must be running Intermec Fingerprint v8.00 (or later).
• EasyCoder PX4i and PX6i printers must be running Intermec Fingerprint v8.30 (or later).
Installation Instructions
Font Card
(for EasyCoder® PF2i, PF4i, PF4ci, PM4i, PX4i, PX6i Printers)
Intermec Technologies Corporation
Worldwide Headquarters 6001 36th Ave.W. Everett, WA 98203 U.S.A.
There are U.S. and foreign patents as well as U.S. and foreign patents pending.
Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and/or other countries.
97257100.PCX 97257430.TXT 97257530.TXT 97257630.TXT 97257730.TXT
5332 292 220 730 685
The .uff file is the only file that varies between different font cards. The .uff file will create two files on the device "rom:"; one .bin file that contains the actual font and one .ncd file that contains the character set for the font. To see the .bin and .ncd files, issue these instructions:

Linear 2合1 BluePass 多技术读卡器安装说明说明书

BluePass2-N-1 BluePass Multi-Tech Reader ManualInstructionsP/N: 10019179 X15Reader Wiring (1)Cable Requirements (1)Output Formats (1)Grounding (1)Power (1)Voltage (1)Connection (1)Mullion Mounting (3)Single-Gang Mounting (4)Setting Up an Account (4)Frequently Asked Questions (5)Troubleshooting (6)Certiﬁ cations ........................................................................6IntroductionThe Linear 2-N-1 BluePass Multi-Tech Reader is a combination legacy proximity card reader and an advanced Bluetooth Low Energy all-in-one reader. This reader is intended for use in conjunction with an access control system that manages physical access to a protected area. This reader allows for an access request to be transmitted to a control panel using the industry standard Wiegand protocol. End-users can present any combination of 125 KHz prox cards and Fobs, or Bluetooth Low Energy Credentials via a supported smart device such as Android and Apple mobile devices to request access using the Linear 2-N-1 BluePass Multi-Tech Reader.This guide is intended as a brief reference used by an experienced technician. For additional information, please visit the Linear website at https://bluepasscloud.io.Mounting ProvisionsThis reader supports both single-gang and mullion-mount housings and is intended for both indoor and outdoor installations.The installation and wiring of this reader must be done in accordance with the National Electric Code and ANSI/NFPA 70. Model: 2N1-BTPRXOrdering Part Number: 820-000012-N-1 BluePass Multi-Tech Reader, BLE/125 KHzMullion Mount Single-gang Mountwith Adaptor Plate(Adaptor included in packaging)ContentsCopyright © 2018 Nortek Security & Control LLC1Cable RequirementsBelden 9535 or equivalent. Multi-conductor stranded with foil shield, minimum 24AWG. Maximum length 400ft (152m).Output Formats26 to 37-bit Wiegand formats.GroundingShield must run continuously from the reader to the panel. At the panel, the reader ground, shield line, and earth ground must be connected together at a single point.Notes:• Do not ground the shield line at the reader end, as this will create a potential ground loop.• Ensure the shield foil and wire are taped and not exposed.PowerA non-switching power supply at the panel is recommended to power the reader for the highest noise immunity and best performance.We recommend using Linear’s stand-alone power supplies for optimum performance.Voltage• Current Draw: 100 - 200 mA typical, 225 mA max peak @ 12 VDC in low-power mode.• At the Reader: +5.5 - 16 VDC. 12.0 VDC is recommended. A regulated power supply and 12 VDC at the reader is recommended for best operation.Note: The reader is in Low Power Mode by default. High-Power Mode can be con ﬁ gured via the Phone App.ConnectionConnections must be in accordance with NFPA 70.WARNING: DO NOT connect this reader’s power supply to a receptacle controlled by a switch.Voltage: +5.5 VDC – 16.0 VDC (12 VDC Nominal) at the reader Curent Draw: 100 - 200 mA (typical @ 12 VDC), 225 mA max peak @ 12 VDC low-power mode.OverviewThe Linear BluePass Multi-Tech Reader provides a simple and convenient way to leverage state of the art BLE mobile credentials for access control. Whether for a new site installation or an upgrade of an existing system, realizing, realizing the power of mobile credentials is a very simple process. In this guide, we will walk you through setting up and conﬁ guring the necessary to get started.There are several major components in the Linear BluePass ecosystem solution illustrated in this guide:1. The Linear BluePass Cloud – This is a web-based portal usedby the dealer/installer/facility administrator to manage mobile credentials.Portal functionality includes the following for issuing and managing electronic credentials:a. Redeem store, and distribute your Credential-To-Go™cards for mobile credential credits.b. Deﬁne top level Organizations in which end-users haveaccess to via mobile credentials.c. Issue mobile credentials to end-users for access to anOrganization.d. Manage existing BLE credentials, their associatedWiegand IDs, and view reports on the number of credentialcredits remaining for issuance.2. The BluePass Mobile Application – This mobile app isavailable for both iOS and Android and is intended for use by end-users of an organization to gain entry to a protected area using a BluePass Multi-Tech Reader. This app displays virtual credentials assigned for use when the app is opened.Under normal circumstances, the app runs in the backgroundMounting the ReaderMounting LocationIf the unit is used to control a door or pedestrian gate, locate the unit as near as practical to the entry point. If the unit is mounted on or in a wall adjacent to the entry point, ensure the wall is sturdy. The repeated shock and vibration from a slamming door or spring-loaded pedestrian gate must be isolated from the unit. Note: Placing a unit directly on a moving door or gate will damage the reader’s sensitive functionality.Choose a well-lit location near the controlled opening. Wiring access for power, network, and earth ground must be available to the mounting location. This reader supports both single-gang and mullion-mount applications and is intended for both indoor and outdoor installations.The installation and wiring of this reader must be done inaccordance with the National Electric Code and ANSI/NFPA 70.Mullion Mount Single-gang Mountwith Adaptor Plate of the user’s mobile device, transmitting the end-user BLE credential to the reader when the user activates the reader’s capacitive touch sensor, typically by touching the reader.a. The Installer Permission Credential + the BluePass APP –Is designed speciﬁ cally for the dealer/installer to conﬁ gureand manage BluePass Multi-Tech Readers installed atthe Organizations they manage. This type of credential isgranted by checking the installer Permission box locatedat the bottom of the “Add User” page.This Permission allows the Administrators/Installers to:b. Enroll (assign) your reader to a speciﬁ c Organizationconﬁ gured in the Dealer Portal account.i. Change setup conﬁgurations of individual readerhardware, such as BLE range requirements foracceptance of access requests, and the readerpower setting for LED intensity and animations.ii. Over-The-Air (OTA) ﬁrmware upgrades and advanced version reporting.3. The Linear BluePass Multi-Tech Reader – This is the physicalreader hardware that supports a standard mullion-style or U.S. single-gang mounting installation. The reader supports26 to 37-bit HID™ compatible 125 KHz Wiegand prox cards,as well as the Linear BluePass Mobile Credential. The reader is conﬁ gured using the Linear Dealer/Installer Mobile Application during installation.4. Note: There is no separate Linear Dealer/Installer MobileApplication. It is the type of credential sent that opens up additional functionality in the common APP.2Copyright © 2018 Nortek Security & Control LLCMullion MountingThe reader can be mounted on a wall or any suitable ﬂ at surface. The Mullion-mounted BluePass Reader can be installed as a new device, or replace an existing one. Depending on the mounting location, new mounting screws may be necessary. These instructionsassume no previous mounting hardware exists.To properly mount the BluePass Reader, perform the following steps: 1. Identify a suitable location for mounting with proper powersupply.2. Mark location on wall for mounting screws approximately 3inches apart with the power supply wires in center.3. Drill two holes.4. Install wall anchors to support mounting screws.5. Feed power cable through mounting bracket’s centeropening.6. Place mounting bracket on wall, aligning screw mountingpositions with wall anchors.7. Insert two (2) screws.8. Connect Reader wires to corresponding Wiegand wiring onpanel.9. Connect the power supply wires to BluePass Reader.Note: Ensure power supply is not energized until all wiresare properly connected and terminated.10. Feed excess cable into wall.11. Mount BluePass Reader into upper and lower mountingstubs.Once completed, the BluePass LED ring will illuminate amber.The administrator establishes the proper online credentialsproﬁ les that enables the reader to function properly. Afterthe proﬁ les are created and the initial scan is complete, the illumination ring will change to blue.ADA Mounting Height RequirementsADA has certain height and reach requirements to allowaccess for persons in wheelchairs.• Keypads should be mounted so that the top of the numbertouchpad is no more than 48” above the ﬁ nished ﬂ oor with noobstructions in locations where wheelchair access is available only from the front.• Keypads should be mounted so that the top of the numbertouchpad is no more than 54” above the ﬁ nished ﬂ oor withno obstructions in locations where the wheelchair hassideways access.BluePass Reader Mullion Mounting Bracket3Single-Gang MountingThe reader can be mounted on a wall or any suitable ﬂ at surface. The Single-Gang mounted BluePass Reader can be installed as a new device, or replace an existing one. If the BluePass Reader is replacing a legacy device, the Single-Gang mounting method is recommended. The mounting plate can be utilized to cover various sized holes in the wall’s surface. Depending on the mounting location, new mounting screws may be necessary. These instructions assume no previous mounting hardware exists.Follow these steps to properly mount asingle-gang BluePass Reader: Array 1. Identify a suitable location for mounting with proper powersupply.2. Mark location on wall for mounting screws approximately 3inches apart with power supply in center.3. Drill two holes.4. Install wall anchors to support mounting screws.5. Feed power cable through mounting bracket’s center opening.BluePass Reader Wiring Diagram6. Place mounting bracket on wall, aligning screw mountingpositions with wall anchors.7. Screw in two (2) screws.8. Connect Reader wires to corresponding Wiegand wiring onpanel.9. Connect the power supply wires to BluePass Reader.Note: Ensure power supply is not energized at time until allBluePass Reader Single-Gang Mounting Bracket wires are properly connected and terminated.10. Feed excess cable into wall.11. Mount BluePass Reader unto upper and lower mounting stubs.Once connected, the illumination ring will change to a default color of blue after the reader has been enrolled into an organization by the the installer.Setting Up an AccountLog onto https://bluepasscloud.io to set up an account. An Installer credential is required to conﬁ gure the readers and test the system. Standard 125Khz credentials can be read by touching the reader. The led ring will ﬂ ash indicating it is ready for the user to present a card or fob. The unit will beep if recognized but not enrolled. The BluePass reader LED will turn green if enrolled in the system the reader is connected with.4Copyright © 2018 Nortek Security & Control LLCFrequently Asked QuestionsHow much power does the BluePass Reader use?• 100-200mAtypical,*************************************************************.• High power mode - 120 mA @ 12 VDCWhat voltage does the reader require?• +5.5 - 16 VDC at the reader. Regulated power supply and 12 VDC at the reader is recommended for best operation.What prox cards does the reader support?• The reader supports HID™ compatible 26 - 37-bit 125KHz Wiegand formatsOther bit formats will be supported in the future with OTA reader ﬁ rmware updates.What card technologies are supported?• 125 KHz Prox and Bluetooth Low EnergyWhich RFID modulations are supported?• EM4102 (ASK modulation)• ISOProx II (HID™ Prox II H10301 compatible FSK modulation)Does the reader support RS-485/OSDP?• Not at this time.How can it replace an existing reader?• Swapping of an existing 26 to 37-bit 125 KHz reader with a new BluePass Reader and is simple and easy with commonWiegand wiring.What do I do if I am replacing a single-gang reader with this mullion reader?• The mullion reader comes with a U.S. single-gang adaptor plate. The mounting holes are aligned with the most common mullion readers on the market.Does the reader require any special access control panel features to work?• No. The Reader is compatible with most preexisting access control panel that supports standard Wiegand protocol input/output. Mobile ApplicationsWhat phones/devices are supported?• Any Apple device running iOS 10.0 or higher• Android devices running Android v5.0 (Lollipop) or higher that supports BLE peripheral mode.Does the Linear App have to be running in the foreground or “active” to enter a door?• No, as long as the app has been launched after the phone is powered on, it can run silently in the background without any further interaction by the user needed to enter a door, except for presenting the phone to the reader.Do I have to present my phone to the reader to enter a door?• The allowed distance between reader and mobile device is conﬁ gurable by the facility manager on a per reader basis. The range can be restricted such that a user must present the mobile device to the reader much like a legacy prox card. Alternatively the range setting can be relaxed allowing the user to simply wave their hand near the reader and leave the mobile device in their pocket, backpack, or purse when requesting access.• We strongly recommend that in most cases the BLE range settings of the readers be set to the shortest range possible to prevent inadvertent access into the building and for the highest level of security.How do I receive Bluetooth Credentials to a building?• You will receive an email from your facility manager to download the mobile application and mobile credential.Select the link for each step to successfully download the app and accept the credential.How do I get the mobile app?• Typically, you will download the apps via the App Store for iOS and the Play Store for Android.Do I have to have an internet connection to enter a door using a mobile key?• No, once you have accepted the BluePass Mobile Credential on your mobile device it is securely stored on the device and requires no network connectivity to request access to a door. Only Bluetooth is required.Are mobile keys secure?• The BluePass Mobile Credential uses the CORE™ platform which features a robust security architecture. It is based on the largest mobile key platform in the world with more than 135 million access transactions to date. Credentials feature AES128 encryption using a PKI implementation that meets or exceeds industry standard best practices.As a facility manager, how do I issue, modify or revoke mobile credentials for my users?• Facility managers have access to a simple web portal that allows them to redeem credential credits using Credential-To-Go™ cards, create new end-users, or modify existing end-users. These actions take effect immediately on the end-user mobile device. Note: Additional FAQ information can be found by visiting https://bluepasscloud.io.5Certiﬁ cationsTroubleshootingFCC Compliance Statement: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and,2. This device must accept any interference received, including interference that may cause undesired operation.Product can be used without license conditions or restrictions in all European Union countries, including Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Luxembourg, The Netherlands, Portugal, Spain, Sweden, and the United Kingdom, as well as other non-EU countries, including Iceland, Norway, and Switzerland.Nortek Security and Control LLC reserves the right to change speciﬁ cations without notice.The reader will not read cards and fobs.Check cards and fobs to ensure they are HID™ compatible 26to 37-bit 125 KHz RFID.End-user was issued credentials and replaced their mobiledevice with a newer model. They downloaded the app and usedtheir original e-mail invite link to reinstall credentials on theirnew device. The installation was unsuccessful.BluePass mobile credentials are only good for the life of theoriginal mobile device. Once a new device is purchased, newcredentials are required, even if the phone number and emailhave not changed.I installed the system in a multi-tenant residential condominiumcomplex. The property management company wants to re-usemobile credentials from departing tenants, reissuing them tothe new tenants moving in. Is there an option in the dashboardto repurpose the same credentials without having to buy themeach time this happens?No. BluePass Credentials are tied to speciﬁ c mobile devices.The only way the property management ﬁ rm could do this is ifthey owned the mobile devices, repurposing the device froma departing tenant to a new tenant. A more viable and lessexpensive option would be to use BluePass Bluetooth fobs.Our customer wants to fully migrate away from 125 KHz cardsand fobs, turning off that portion of the reader so it will only readthe Bluetooth-based credentials. Can I turn off that portion ofthe reader?Currently, you cannot turn off the 125 KHz portion of a reader.My customer has a home access control system and hasprogrammed it so he can use the same fob that he usesto access the building at his work, he simply programmedthe same legacy credential ID number from his fob into hishome system. This makes it convenient, requiring him toonly need one credential. Does the BluePass system allowfor the same thing?No. The system is speciﬁc to each organization. Yourcustomer’s home reader will not read the employer’sBluePass credential at all. The customer will need to havetwo BluePass credentials; one for home and one for work.When the customer replaces their mobile device, two newcredentials will need to be purchased.P/N: 10019179 X15Copyright © 2018 Nortek Security & Control LLC。

MBFE密押卡安装手册

第一章SJL10-B CNAPS密押卡简介中国人民银行现代化支付系统SJL10-B密押卡是为保证中国人民银行现代化支付系统支付业务数据交换的完整性而研制的专用密码设备。

SJL10-B密押卡是应用层密码设备，它以应用程序接口（API）的方式为目标提供支付业务信息的编/核密押处理服务。

SJL10-B密押卡具有物理安全的特性：拥有防撬检测电路，确保密钥及密码算法不会暴露于物理安全的环境之外，有效地保护应用系统的安全运行。

SJL10-B密押卡提供的主要功能如下：（1）支持ANSI和ISO安全标准（2）支持MAC（密押）的生成和校验（3）安全完善的密钥管理功能（4）支持IC卡密钥存取功能（5）支持IC卡身份认证（6）通过配置管理终端对密押卡进行灵活配置在密押卡硬件安装结束后，要对密押卡进行配置管理操作，通过成功地配置密押卡的密钥系统、操作员卡和口令等，密押卡的编/核押功能才能正常启用。

第二章安装2.1装箱单打开包装盒后，请首先检查密押卡套件是否齐全：1.SJL10-B CNAPS密押卡一块2.操作员卡一张3.密押卡系统盘一张4.用户手册一本5.合格证说明：如果发现配件与装箱单不符，请及时与供货商联系。

2.2密押卡的安装一般地，密押卡硬件安装步骤如下：（1）关闭计算机电源；（2）打开机箱；（3）找到一个空闲的PCI插槽；（4）卸下插槽挡片；（5）小心地将密押卡插入PCI插槽；（6）拧紧密押卡挡片螺丝；（7）盖上机箱；（8）固定外置式读卡器。

将读卡器电缆接口紧密地连接至密押卡9芯接头上；（9）打开计算机电源。

2.3驱动程序安装首先，在密押卡目标主机上建立密押卡专用目录，如下描述：◆ Windows平台：建立C:\SJL10 及其子目录C:\SJL10\drv◆ UNIX平台：建立/SJL10 及其子目录/SJL10/drvWindows 95/98及Windows 2000关闭PC机电源，将密押卡插入PCI插槽中.开启电源，开机，这时系统自动发现新硬件，并提示“找到新的硬件，正在查找它的软件”。

学生保镖(都联卡)说明书

一、都联卡介绍：都联卡是针对于中小学生、老人等弱势群体开发的一款监护设备，能够查询使用者的实时位置信息，记录使用者的日常活动轨迹，到离校通知，指定区域禁入、禁出提醒；集成普通手机功能，常用联系人一键拨通，内置防火墙屏蔽不明电话骚扰，在使用者不方便接听时下发语音留言、振动通知等。

是爱护儿童、关爱长辈必备的智能产品。

二、装箱清单都联卡、电池、充电器、数据线、保修卡、激活卡、产品使用手册、螺丝刀、挂绳。

三、使用前须知请先购买一张移动或联通SIM卡并安装于都联卡中★确保SIM卡开通GPRS功能，建议使用GPRS套餐（节省话费）★确保SIM卡开通来电显示功能★确保SIM卡有足够的话费温馨提示：插入或取出SIM卡之前，请先将都联卡关机。

四、认识你的都联卡4.1开/关机开机：长按侧面第二个键3秒钟松开。

关机：卸下都联卡电池，都联卡自动关机。

温馨提示：为了避免被监护对象自行关机以躲避监护人的管理，都联卡无法通过常规方法进行关机，但在某些需要关机的特殊情况下可以通过拔出电池方式强行关机。

4.2电池的充电及使用将充电器插上电源，将充电线的插头插入都联卡的充电口。

充满电时间大约在3-5个小时之间。

都联卡日常使用时，电源指示红色LED灯快速闪烁时，表示电池电量过低，应及时充电。

在给都联卡充电时，红色电源LED灯闪烁状态，表示在给电池充电；红色电源LED灯长亮时，表示电池已充满。

温馨提示：初次使用都联卡，请保持都联卡处于室外环境，并处于开机状态。

五、激活你的都联卡5.1注册/登录帐号使用浏览器登录都联网平台（）点击右上方的”注册”按钮。

填写相关信息，即可完成注册；注册完成后可点击都联网右上方的”登录”按钮。

输入注册的用户名、密码登录平台。

温馨提示：注册账号时，手机号可不填写，填写邮箱和手机号的目的主要是用于忘记密码时找回账号、密码。

（图为：注册）（图为：登录）5.2新增/激活都联卡登录后点击导航栏中的“我的设置”按钮，点击页面中的都联卡管理的“新增都联卡”按钮，在“激活都联卡“对话框里，输入包装盒里激活卡片上的卡号与激活码。

DS-K1100系列安装手册v1.0

DS-K1100系列读卡器安装手册UD.6L0106B0088A01非常感谢您购买我司产品，如有任何疑问或需求请随时联系我本手册可能包含技术上不准确的地方、或与产品功能及操作不相符的地方、或印刷错误。

我司将根据产品功能的增强或变化而更新本手册的内容，并将定期改进及更新本手册中描述的软硬件产品。

更新的内容将会在本手册的新版本中加入，恕不另行通知。

本手册中内容仅为用户提供参考指导作用，不保证与实物完全一致，请以实物为准。

本手册中提到的部件、组件和附件仅作说明之用，不代表购买机型的配置，详细配置请以装箱单为准。

1.读卡器外观尺寸1.1DS-K1101系列读卡器DS-K1101MK/DS-K1101CK DS-K1101M/DS-K1101CDS-K1102MK/DS-K1102CK DS-K1102M/DS-K1102CDS-K1103MK/DS-K1103CK DS-K1103M/DS-K112.读卡器后接口2.1DS-K1101系列读卡器后接口3.读卡器的安装3.1PSAM卡安装（仅适用于CPU卡读卡器）在PSAM3.2读卡器拨码说明拨码开关从左到右为最低位到最高位，即从左到右为1～8。

黑色在ON的一端表示10当拨码开关如下图所示：则对应的二进制为：0000 1100，表示的十进制为：地址=12。

3.3读卡器尾线接线定义3.4读卡器尾线接线方式（RS485）3.5读卡器尾线接线方式（Wiegand协议）3.6读卡器安装●安装前请先进行拨码设置和尾线接线。

●安装读卡器固定板时，请勿用力过大以避免造成弯曲变形。

(A)将安装固定板固定在墙上或其他位置(B)依照接线说明将线接上，并将各接线端子插上(C)读卡器上方对准固定板卡榫(D)将读卡器往固定板方向密合(E)使用六角扳手将螺丝由下方底部密合锁上(F)请撕掉保护膜4.测试读卡器通电启动，LED状态灯先蓝色闪烁1次再红色闪烁3次，再蜂鸣器发一声鸣叫，提示用户启动成功。

K-LiteMegaCodecPack安装向导

K-LiteMegaCodecPack安装向导K-Lite Mega Codec Pack安装向导说明：本向导只针对K-Lite Mega Codec Pack软件有效，请耐心的看红圈提示操作。

1、双击K-Lite Mega Codec Pack安装程序，点Next；2、选择红圈的项目，点Next；3、安装路径保持不变，点Next；说明：C盘空间允许的情况下，建议装在C盘。

4、此步不要随意改动选项，除非你懂的...，点Next；5、点Next继续；6、此步用3张图片显示，有4个地方要勾选；①勾选“Reset all settings to their defaults”②勾选“Desktop shortcut for Media Player Classic”12将滚动条拉至中下位置③勾选“Install language files for MPC”3将滚动条拉至底部位置④去掉“Visit a website with codec news”前的“√”4 勾选上面4处后，点Next；7、按照下图的选项来选择解码方式，点Next；8、勾选红圈中的项目，目的是让Windows Media Player能播放更多格式的文件，点Next；9、此步是让Media Player Classic播放的文件格式，请不要改动，点Next；10、此步是让Windows Media Player播放的文件格式，请不要改动，点Next；11、勾选“Windows Media”项，点Next；12、此步是选择用几路声道输出音频的，根据自己的需要选择，默认为2.0立体声，点Next；13、勾选“No thanks, I don’t want any of the above.”，点Next；14、直接点Install，软件开始安装；15、勾选“Configure ffdshow video decoder”，点Finish；16、左边点“Tray,dialog & paths”，右边点下拉菜单，选择“简体中文”；17、效果图，点确定；至此，K-Lite Mega Codec Pack软件的安装结束。