注塑机常用英语

注塑模具英语词汇

注塑模具英语词汇-CAL-FENGHAI.-(YICAI)-Company One1注塑模具英语词汇一、工程部 / Design department:1) Designer - 设计师。

2) Assembly drawing - 模具组装图。

3) Mold layout - 模具结构图。

4) 2D product drawing - 2D产品图。

5) 3D product data - 3D产品数据。

6) Part drawing - 散件图。

7) Insert molding - 镶件模。

8) 2 color mold / Double injection tool - 双色模。

9) Hydraulic system - 油/水压系统。

10) Parting line - 分模线。

11) Air venting - 排气槽。

12) Cooling system - 冷却系统。

13) Screw - 镙丝。

14) Hot runner system - 热流道。

15) Valve gate - 伐针入水口。

16) Fan gate - 扇型入水口。

17) Pin point gate - 针点进胶。

18) Moon gate / Banana gate - 香蕉，象牙入水口。

19) Submarine gate - 潜水口。

20) Injection machine tonnage - 注塑机吨数。

21) Number of cavity - 穴数。

22) Steel - 钢材。

23) Copper - 铜。

24) Tungsten copper - 钨铜。

25) Beryllium copper - 铍铜。

26) Hardening - 加硬/淬火。

27) Tempering - 回火。

28) Chroming - 电镀。

29) Painting - 喷漆。

30) Resin - 胶材。

31) Printing - 丝印。

注塑机专业英语

注塑机专业英语Revised on November 25, 2020钣金 machine cover / upper cover/ side cover锁模部分 clamping unit射胶部分 injection unit机架 machine frame / base电气系统 electric system液压系统 hydraulic system机械系统 mechanical system机门safety door / fixed door / movable door锁模部分 clamping unit电脑控制器 computer controller机械安全锁 mechanical safety interlock射胶部分 injection unit液压系统 hydraulic system电箱 electrical cabinet / cable机架分体线 stand split line机架螺丝孔 foundation bolt hole机架machine base / supporting frame理论注射容积 theoretical shot volume 实际注射量 shot weight螺杆直径 screw diameter注射压力 injection pressure注射速度 injection speed注射速率 injection rate螺杆长径比screw L/D ratio螺杆行程 screw stroke螺杆转速 screw speed熔胶能力plasticizing capacity锁模力 clamping force开模/锁模行程 mold clamping / opening stroke模板尺寸 platen size拉杆间距 distance between tie bars / rods模板最大距离 max. daylight容模量 mold thickness (min. & max.)顶出行程 hydraulic ejection stroke顶出力hydraulic ejection force顶针数 nos. of ejector pin液压系统压力hydraulic system pressure油泵马达 pump motor电热量 heating capacity 温度控制区数 nos. of temp control zones射嘴接触力 nozzle contact forceInjection射出Cooling time 冷却时间Holding time 锁模时间Injection alarm time 射出警报时间Injection start delayFinal cushion minimum valueChange-over to holding by valuePlasticizing end valueHydrarlic change-over pressure holdingScrewvalue for change-over to holdingChange-over to holding by enable valueHydraulic pressure in holding 锁模压力Filling stage pressure limitInjection speed 射出速度Injection注射Cooling time冷却时间Holding timeInjection alarm time注射报警时间Injection start delay注射开始延时Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Change-over to holding by enable valueHydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould closing关模Mould close force关模压力Mould closing safety time.. 时间Mould closing pressure.. 压力1st closing safety stage pressure合模一段压力1st mould closing speed ...成型速度1st stage mould closing speed1st stage mould closing safety position.....位置High pressure start position高压锁模位置Number of repeat mould closing movement..重复次数Holding time 保压时间Injection start delay 注射延迟Injection注射Cooling time冷却时间Holding time保压时间Injection alarm time注射报警时间Injection start delay注射开始延时(注射延时启动延时)Final cushion minimum value最后段位置（最小余量）Change-over to holding by value切换到锁模（保压由位置切换）Plasticizing end value预塑重终点（熔胶终止）Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Change-over to holding by enable value保压由位置切换Hydraulic pressure in holding锁模力（保压）Filling 填充Injection alarm time 射胶时间Injection start delay 延迟射胶Final cushion minimum value 不知道这个是在哪个页面或项目下，如果是射胶那应该是：最小射胶终点（应该是品质项目设置的）Change-over to holding by value不知道这个是在哪个页面或项目下，如果是射胶那应该是：最大射胶终点（应该是品质项目设置的）Plasticizing end value终点位置。

注塑机专业英语

钣金 machine cover / upper cover/ side cover 锁模部分 clamping unit射胶部分 injection unit机架 machine frame / base电气系统 electric system液压系统 hydraulic system机械系统 mechanical system机门 safety door / fixed door / movable door 锁模部分 clamping unit电脑控制器 computer controller机械安全锁 mechanical safety interlock射胶部分 injection unit液压系统 hydraulic system电箱 electrical cabinet / cable机架分体线 stand split line机架螺丝孔 foundation bolt hole机架 machine base / supporting frame理论注射容积 theoretical shot volume实际注射量 shot weight螺杆直径 screw diameter注射压力 injection pressure注射速度 injection speed注射速率 injection rate螺杆长径比 screw L/D ratio螺杆行程 screw stroke螺杆转速 screw speed熔胶能力 plasticizing capacity锁模力 clamping force开模/锁模行程 mold clamping / opening stroke 模板尺寸 platen size拉杆间距 distance between tie bars / rods模板最大距离 max. daylight容模量 mold thickness (min. & max.)顶出行程 hydraulic ejection stroke顶出力 hydraulic ejection force顶针数 nos. of ejector pin液压系统压力 hydraulic system pressure油泵马达 pump motor电热量 heating capacity温度控制区数 nos. of temp control zones射嘴接触力 nozzle contact forceInjection射出Cooling time 冷却时间Holding time 锁模时间Injection alarm time 射出警报时间Injection start delayFinal cushion minimum valueChange-over to holding by valuePlasticizing end valueHydrarlic change-over pressure holding Screwvalue for change-over to holdingChange-over to holding by enable valueHydraulic pressure in holding 锁模压力Filling stage pressure limitInjection speed 射出速度Injection注射Cooling time冷却时间Holding timeInjection alarm time注射报警时间Injection start delay注射开始延时Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Change-over to holding by enable valueHydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould closing关模Mould close force关模压力Mould closing safety time.. 时间Mould closing pressure.. 压力1st closing safety stage pressure合模一段压力1st mould closing speed ...成型速度1st stage mould closing speed1st stage mould closing safety position.....位置High pressure start position高压锁模位置Number of repeat mould closing movement..重复次数Holding time 保压时间Injection start delay 注射延迟Injection注射Cooling time冷却时间Holding time保压时间Injection alarm time注射报警时间Injection start delay注射开始延时(注射延时启动延时)Final cushion minimum value最后段位置（最小余量）Change-over to holding by value切换到锁模（保压由位置切换）Plasticizing end value预塑重终点（熔胶终止）Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Change-over to holding by enable value保压由位置切换Hydraulic pressure in holding锁模力（保压）Filling 填充Injection alarm time 射胶时间Injection start delay 延迟射胶Final cushion minimum value 不知道这个是在哪个页面或项目下，如果是射胶那应该是：最小射胶终点（应该是品质项目设置的）Change-over to holding by value不知道这个是在哪个页面或项目下，如果是射胶那应该是：最大射胶终点（应该是品质项目设置的）Plasticizing end value终点位置。

注塑机相关名词中英文对照

58 driller
鑽床
93 general manager
總經理
59 easily damaged parts
易損件
94 glove(s) with exposed fingers 割手套
60 education and training
教育與訓練 95 grease/oil stains
油污
61 electric screw driver
縮水
172 production department
生產部門 207 shut die
架模
173 production line
流水線
208 shut height of a die
架模高度
174 production unit 175 production, to produce
生產單位生產
209 sliding rack
送料不到位
44 delivery deadline
交貨期
79 final inspection
終檢
45 delivery, to deliver 46 demand and supply 47 dents
交貨需求壓痕
80 fit together 81 fixture 82 flow board
補漆
184 rear plate
後板
150 painting peel off
髒汙
185 receive
領取
151 PAL Pallet/skid
棧板
186 registration
登記
152 pallet
棧板
187 registration card

注塑机专业英语

保压后制品在模具内部成型完毕脱离模具的现象方便成型制品脱离模具而设计的角度成型制品不容易脱离模具的现象残留在制品内部因各种原因产生的应力很多小分子连接而成的具有较大质量的长分子连熔体在模具内冷却状态之一的数学表示方法成毛型坯后加制工品或拿留出有的大过量程余量的待加工品配完合成C一PU个工组作件的或马产达品经过的步骤以塑料为原料生产的制品通过注射方式成型的模具倾斜于分型面、随模具的开闭产生相对运动的圆柱零件斜向镶块或滑动的镶块组合方式之一使镶件或拼块定位并紧固在一起的框套形结构零件成型模具内表面突起的组件使动模能固定在压机或注塑机上的L型垫块在腔内起部分成型作用，并在开模时把塑件从型腔内推出的零件用于推出塑件或浇注系统凝料的杆件支撑推出和复位零件，直接传递机床推出力的板件借助模具的闭合动作，强制推出机构复位的杆件浇口的相关尺寸熔融塑料经主流道直接进入型腔的进料方式沿塑料件内圆周扩展进料的浇口设置在模具的分型处从塑件的内或外侧进料的方式从分流道道型腔方向的宽度逐渐增加的呈扇型的浇口
斜销斜滑块
悬臂搭扣连接模套型芯支架推块推杆推板复位杆浇口尺寸直接浇口盘式浇口侧浇口扇形浇口
demolding draft ejection difficulties internal stress long chain macromolecules frozen layer fraction removal rough machining servomotor workstage plastic parts injection mould angle pin / finger cam angled-lift / splits cantilever snap joints chase / bolster / frame Core ejector housing / mould base leg ejector pad ejector pin ejector plate push-pack pin Gate dimensions(sizes) direct gate;sprue gate disk gate edge gate fan gate

注塑英语大全成型工艺流程及条件介绍Molding technique procedure and parameter introduction 第一节成型工艺Section 1 molding technique.1.成型工艺参数类型Sorts of molding parameter.(1).注塑参数ction parameter.a.注射量ction rate.b.计量行程Screw back positionc.余料量Cushiond.防诞量Sucking back ratee.螺杆转速Screw speedf.塑化量Plastic0 rateg.预塑背压Screw back pressureh.注射压力和保压压力ction pressure and holding pressurei.注射速度ction speed(2)合模参数Clamping parametera.合模力Clamping forceb.合模速度Clamping speedc.合模行程.Clamping stroked.开模力Opening force e.开模速度Opening speed f.开模行程Opening positiong.顶出压力Ejector advance pressureh.顶出速度Ejector advance speedi.顶出行程Ejector advance position2.温控参数Temperature parametera.烘料温度Dry resin material temperatureb.料向与喷嘴温度Cylinder temperature and nozzle temperaturec.模具温度Mold temperatured.油温Oil temperature3.成型周期Molding cyclea.循环周期Cycle timeb.冷却时间Cool timec.注射时间ction timed.保压时间Holding pressure timee.塑化时间Plant timf.顶出及停留时间Knocking out and delay timeg.低压保护时间Mold protect time成型工艺参数的设定须根据产品的不同设置. Molding technique parameter setting differs depending on type of product第二节成型条件设定Section 2 Molding parameter Setting按成型步骤:可分为开锁模,加热,射出,顶出四个过程.Molding steps: mold opening/closing, heating ction and knocking out.开锁模条件: Mold opening parameter:快速段中速度High-speedmid-speed低压高压速度Low pressure high pressure speed锁模条件设定: Mold closing parameter setting1锁模一般分:快速→中速→低压→高压Mold closing: high-speed →low-speed →low pressure→high pressure。

注塑机常用英语

注塑英语大全成型工艺流程及条件介绍Molding technique procedure and parameter introduction 第一节成型工艺Section 1 molding technique.1.成型工艺参数类型Sorts of molding parameter.(1).注塑参数ction parameter.a.注射量ction rate.b.计量行程Screw back positionc.余料量Cushiond.防诞量Sucking back ratee.螺杆转速Screw speedf.塑化量Plastic0 rateg.预塑背压Screw back pressureh.注射压力和保压压力ction pressure and holding pressurei.注射速度ction speed(2)合模参数Clamping parametera.合模力Clamping forceb.合模速度Clamping speedc.合模行程.Clamping stroked.开模力Opening force e.开模速度Opening speed f.开模行程Opening positiong.顶出压力Ejector advance pressureh.顶出速度Ejector advance speedi.顶出行程Ejector advance position2.温控参数Temperature parametera.烘料温度Dry resin material temperatureb.料向与喷嘴温度Cylinder temperature and nozzle temperaturec.模具温度Mold temperatured.油温Oil temperature3.成型周期Molding cyclea.循环周期Cycle timeb.冷却时间Cool timec.注射时间ction timed.保压时间Holding pressure timee.塑化时间Plant timf.顶出及停留时间Knocking out and delay timeg.低压保护时间Mold protect time成型工艺参数的设定须根据产品的不同设置. Molding technique parameter setting differs depending on type of product第二节成型条件设定Section 2 Molding parameter Setting按成型步骤:可分为开锁模,加热,射出,顶出四个过程.Molding steps: mold opening/closing, heating ction and knocking out.开锁模条件: Mold opening parameter:快速段中速度High-speedmid-speed低压高压速度Low pressure high pressure speed锁模条件设定: Mold closing parameter setting1锁模一般分:快速→中速→低压→高压Mold closing: high-speed →low-speed →low pressure→high pressure。

注塑机常用术语英汉对照表

alternatingcurrent直流电dcdirentcurrent保险fuse电压vvoltage电流acurrent开关switch半自动semiauto电机mmotor油泵pmpump液压hydraulicposhow电眼dhotosensor二极管ddiode三极管ttransistor电阻器rresistance电容器ccapacitor电感器linducer发光二极管luminescentdiode光电耦合器photocoupler喷嘴nozzle顶针ejector时间继电器sjtimer电磁继电器jrelay过流继电器rjovercurrentrelay交流接触器cjelectromagneticcontanctor限位开关limitswitches按钮开关pushbuttonswitches控制开关controlswitches接近开关proximityswitches温度计thermometer热电偶thermocouple热电阻thermistor恒温器thermostat电磁阀solenoidvalve控制阀controlvalve卸载阀reliervalve压力油hydraulicoil润滑油lubricationoil油温计oilthermometer真空计vacuumgaugegaugevalve软管hoses水套管waterjacket无缝管seamlesstube线圈coil触点point联轴器rotaryjoint密封垫圈sealing型胶圈oring衬垫packing衬套liner油封oilsealing油缸cylinder轴承spring法兰flange螺栓nut螺母bolt螺杆screwbarrel射坐后退carragemeltdecomp多次顶出multi一次顶出hold调模向前small调模向后large低压锁模时间lowclampingtime差动锁模fastmoldcloses吹风airblowing成品器件partcoreout顺时针转动螺杆unscrewcw逆时针转动螺杆unscrewccw计数器counter操作operation制表人

注塑机使用的英语词汇

4.成型周期
Molding cycle
a.循环周期
Cycle time
b.冷却时间
Cool time
c.注射时间
Injection time
d.保压时间
Holding pressure time
e.塑化时间
Plant time
f.顶出及停留时间
Knocking out and delay time
g.低压保护时间
注塑机词汇
1.注塑参数
Injection parameter.
a.注射量
Injection rate.
b.计量行程
Screw back position
c.余料量
Cushion
d.防诞量
Sucking back rate
e.螺杆转速
Screw speed
f.塑化量
Plastic rate
g.预塑背压
c.合模行程.
Clamping stroke
d.开模力
Opening force
e.开模速度
Opening speed
f.开模行程
Opening position
g.顶出压力
Ejector advance pressure
h.顶出速度
Ejector advance speed
i.顶出行程
Ejector advance position
Mold protect time
Screw back pressure
h.注射压力和保压压力
Injection pressure and holding pressure
i.注射速度
Injection speed

注塑机必备英语的

注塑机各部件的中英文名称和作用shear剪切back pressure 背压no zzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubricati on 润滑Inject ion machi ne 啤机Shot size ( weight ）实际射胶量injectio n volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar cleara nee 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒,机筒clamp force 锁模力non-retur n valve 止回阀ope ning stroke 开模行程Injectio n pressure 射胶压力work horse 主力，主要设备Reserve pressure pack ing pressure 保压mold trial 试模shot （一）啤Decompress 减压oven烤炉，烘灶shri nkage rate 收缩率Reside nee time 滞留时间injection speed 注射速度booster time 增压时间Compressi on ratio 压缩比mold close time 合模时间Resin胶料Plasticizatio n 塑化，增塑viscosity 粘性，粘度con tam in ati on 污染，杂物Thermoplastic 热塑性塑料thermosett ing plastics 热固性塑料Booster time 增压时间feed喂料，填充purge 净化Flame retarda nt 阻燃degradati on 降解，软化regrind 再粉碎Water absorpti on 吸水rei nforce 增强，加固specific gravity 比重Elo ngation 延伸率den sity 密度melti ng point 熔点Polystyrene 聚苯乙烯（PS）Styrene 苯乙烯Acrylo nitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethyle ne 聚乙烯glass fiber 玻纤Conden sation 凝固，浓缩crystalli ne res in 结晶形塑料compre sio n moldi ng 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕weldi ng mark 溶合痕post screw in sert 螺纹套筒埋值self tapp ing screw 自攻螺丝striper plate 脱料板pist on 活塞cyli nder 汽缸套chip细碎物han dle mold 手持式模具（移转成型用模具）en capsulation moldi ng 低压圭寸装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井in sulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spi ndle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道weld ing line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子nner stripper plate 浇道脱料板guide pin 导销eject rod （bar）（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orie ntati on 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销（拉料杆）slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subari ne gate 潜入式浇口tunnel gate隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue浇口;溶渣入水：gate 进入位：gate locati on 水口形式：gate type 大水口：edge gate 细水口：pin-po int gate 水口大小：gate size 转水口：switch ing runn er/gate 唧嘴口径：sprue diameter 流道：runner 热流道：hot runner,hot manifold 热嘴冷流道:hot sprue/cold runner 唧嘴直流:direct sprue gate 圆形流道：roun d(full/half ru nner 流道电脑分析：mold flow analysis 流道平衡:runner bala nee 热嘴：hot sprue 热流道板：hot mani fold发热管：cartridge heater 探针:thermocouples 插头：conn ector plug插座：conn ector socket密圭寸/圭寸料：seal 运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connectorplug/socker模具零件：mold comp onents三板模：3-plate mold二板模：2-plate mold边钉/ 导边：leader pin /guide pin边司/ 导套：bush in g/guide bush ing中托司：shoulder guide bush ing 中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity in ter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）:nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity in sert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/ 油板：wedge wear plate 压条：plate撑头：support pillar唧嘴：sprue bush ing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spri ng rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞：pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：part ing locks活动臂：lever arm复位键、提前回杆：early retur n bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：part ing surface support bala nee 模排气：part ing line venting回针碰料位：return pin and cavity in terfere nee 模总高超出啤机规格：mold base shut hight顶针碰运水：water line in terferes withejector pin料位出上/ 下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件：Do not use (core/cavity) in sert用铍铜做镶件：use beryllium copper insert初步(正式)模图设计：prelii nary (fin al) mold desig n 反呵：reverse core弹弓压缩量：spri ng compressed len gth稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷去卩：eve n cooli ng扣模：sticking热膨胀：thero expansion公差：toloranee铜公(电极)：copper electrode塑料成形模具mould for plastics热塑性塑料模mould for thermoplastics热固性塑料模mould for thermosets压缩模compressi on mould压注模、传递模tran sfer mould注射模injectio n mould热塑性塑料注射模injectio n mould for thermoplastics 热固性塑料注射模injectio n mould for thermoses定模statio nary mould fixed half动模movable mould moving half定模座板fixed clamp plate, top clampi ng plate. top plate动模座板movi ng clamp plate. bottom clampi ng plate. bottom plate上模座板upper clampi ng plate下模座板lower clampi ng plate凹模固定板cavity-reta iner plate型芯固定板core-reta iner plate凸模固定板pun ch-reta iner plate模套chase. bolster. frame支承板back ing plate. supprr plate垫块spacer parallel 支架ejector housing. mould base leg abrasive grinding 强力injectio n mould 注塑模injection 注射in-line-of-draw 直接脱模in sert 嵌件in serted die 嵌入式凹模in specti on 检查，监督in stallati on 安装Surface Appeara nee 夕卜观Gloss in ess/gloss finish 光洁度Matt fini sh/matt surface 毛面Glass fiber rich surface/glass emerge nee on the surface 玻纤外露Bloomi ng/surface bloomi ng 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittle ness 脆Bubbles/trapped gas 气泡Void 孑LBur n marks 烧伤FR failed 阻燃不合格Flame rati ng V-2 阻燃V-2 Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 粒子不密/蜜蜂窝Low impact/te nsile etc 物理性能低High flow/filler con te nt etc 流动性/ 填充…过高Lon gs/fi nes/doubles 长粒/ 碎屑/ 连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孑LGlass bun dles 玻纤结团Product was rejected due to 产品不能接受因为…High moisture level 高水分Warpage/warped 翘曲Shrin kage/shri nk 收缩Si nk marks 缩影Short shot/short moldi ng 打不满Distortio n 变形Over dime nsion 尺寸过大Un der dime nsion 尺寸过小Flash ing 飞边Discolorati on 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模An tioxida nt 抗氧剂Flame retarda nt age nt 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Rovi ng glass fiber 粗纱/ 长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybde num disulfide/moly/MoS2 二硫化钼Colora nt 着色剂Pigme nt 颜料Dye染料Accepted product specificati on 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra … 添加多一点…Reduced …content 减少…含量Dropped/reduced …by x % 减少…含量Con firmed color sta ndard 确认颜色标准Approved color sta ndard 认可颜色标准Re-c on firmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Un dergoi ng heat agi ng test 在做热老化实验Product is un der testi ngReceived first order接了第一个定单Expected to finish by Expected order is xMT产品在测试当中•预计在…完成预计定单量…吨Estimated annu al/m on thly con sumption预计年/月用量SPC statistic process con trol品管保证Quality Assuranee品管控制Quality control来料检验IQC In comi ng quality con trol巡检IPQC In-process quality control校对calibration动态试验dynamic test环境试验Environmental test非破坏性试验non-destructive test光泽gloss击穿电压(dielectric) breakdown voltage拉伸强度tensile strength冷热骤变试验thermal shock test环境试验炉Environmental chamber盐雾实验salt spray test绝缘电阻测试验仪In sulat ing resista nee meter 内应力internal stress疲劳fatigue蠕变creep试样specimen撕裂强度tear strength缩痕shrink mark, sink mark耐久性durability抽样sampling样品数量sample size AQL Acceptable Quality level批量lot size抽样计划sampling plan OC曲线operation curve试验顺序sequenee of tests环境温度ambient temperature可焊性solderability阻燃性flame resista nee总经理办公室General manager ' s office企管咅E Enterprise management department (EM)行政咅 E Admi ni strati on departme nt (AD)销售部Sales department (SD)财务部Financial department (FD)技术部Tech no logy departme nt (TD)物控部Production material control department (PMC)生产部Production department(PD)manu facturi ng 模具咅E Mold manufacturing department, Toolingdepartme nt (TM)实用标准文案品管咅E Quality Assuranee department (QA)冲压车间Stamp workshop, press workshop注塑车间injection workshop装配车间Assembly workshop模具装配车间Mold and die Assembly workshop 金属加工车间metal machine workshop电脉冲车间Electric discharge process workshop 线切割车间wire cutting process workshop 工磨车间Grinding workshop总经理General manager (GM)副总经理Vice-general manager经理manager董事长preside nt副董事长Vice-preside nt XX部门经理Manager of XX department主任、主管supervisor拉长Line leader组长Foreman, forelady秘书secretary文员clerk操作员operator助理assistant精彩文档。

模具注塑术语中英文对照

模具注塑术语中英文对照1. 模具制造工艺 - Mold Manufacturing Process•钳工技术 - Fitting Technology•铣床 - Milling Machine•车床 - Lathe Machine•电火花 - Electrical Discharge Machine (EDM) •线切割机 - Wire Cutting Machine (WCM)•抛光 - Polishing•喷砂 - Sandblasting•组装 - Assembly•检验 - Inspection•测试 - Testing2. 模具材料 - Mold Materials•CNC - Computer Numerical Control•冷/热工作钢 - Cold/Hot Work Steel•韧性铁 - Ductile Iron•钢筋混凝土 - Reinforced Concrete•铝合金 - Aluminum Alloy•有机玻璃 - Organic Glass•尼龙 - Nylon•聚酯树脂 - Polyester Resin•低密度聚乙烯 - Low-Density Polyethylene (LDPE) •高密度聚乙烯 - High-Density Polyethylene (HDPE) 3. 注塑设备 - Injection Molding Equipment•注塑模 - Injection Mold•注塑机 - Injection Molding Machine•螺杆 - Screw•加热筒 - Barrel Heater•喷嘴 - Nozzle•冷却系统 - Cooling System•熔融体 - Melted Polymer•定位环 - Locating Ring•压力机 - Press•模芯 - Core4. 注塑工艺 - Injection Molding Process•熔胶温度 - Melting Temperature •注射速度 - Injection Speed•保压时间 - Holding Time•冷却时间 - Cooling Time•射胶压力 - Injection Pressure•模具温度 - Mold Temperature•注射容量 - Injection Capacity•射出比例 - Injection Ratio•射胶速度 - Injection Rate•开模时间 - Opening Time5. 注塑缺陷 - Injection Molding Defects•缩水 - Shrinkage•气泡 - r Bubbles•热分解 - Thermal Degradation•断裂 - Fracture•变形 - Deformation•熔接线 - Weld Line•流痕 - Flow Mark•挤出线 - Extrusion Line•色差 - Color Variation•异物 - Foreign Object6. 模具维护 - Mold Mntenance•涂抹脱模剂 - Apply Mold Release Agent•清洁模具 - Clean the Mold•磨削模具 - Grinding the Mold•检查模具 - Inspect the Mold•修复模具 - Repr the Mold•涂覆保护液 - Coat with Protective Agent•封存模具 - Store the Mold•更换模具配件 - Replace Mold Components•消除模具表面缺陷 - Eliminate Surface Defects on Mold •升级模具材料 - Upgrade Mold Material以上是模具注塑术语的中英文对照，希望能对你有所帮助。

注塑机英语专业术语

理论注射容量
shot size
注射压力
injection pressure
合模力
clamping force
移模行程
clamping stroke
拉杆内距
space between tie bar
最大模厚
Max.Mold Height
最小模厚
Min.Mold Height
顶出行程
Ejector Stroke
Injection Unit Clamping Unit Motor and Pump Unit Hydraulic System Unit (Include cooling system) Lubrication Unit Door and Cover Frame Electronic Unit Spare Appendix Unit(Label) Plasticizen Subassembly Barrel House Subassembly Bering House Subassembly Nozzle Moving Subassembly Support Subassembly Injection Control Nozzle Move Control Hopper Screw Speed Sensor Clamping cylinder Mold adjust Platen & toggle Clamping control Ejector cylinder Eject control Mechanism Safety device Mold adjust control Moving Platen support
变频器
Frequency converter
液压合模安全保护

注塑机必备英语的

注塑机各部件的中英文名称和作用Injection machine 啤机Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力non-return valve 止回阀shear 剪切opening stroke开模行程Injection pressure 射胶压力back pressure 背压nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要设备Reserve pressure packing pressure保压mold trial 试模 shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度booster time 增压时间Compression ratio 压缩比mold close time 合模时间Resin 胶料Plasticization 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降解，软化regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重Elongation 延伸率density 密度melting point 熔点Polystyrene 聚苯乙烯（PS）Styrene 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethylene 聚乙烯glass fiber 玻纤Condensation 凝固，浓缩crystalline resin结晶形塑料compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子nner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 流道:runner 热流道：hot runner,hot manifold 热嘴冷流道:hot sprue/cold runner 唧嘴直流:direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头： connector plug插座： connector socket密封/封料： seal运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 模具零件： mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板： support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针： ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode塑料成形模具 mould for plastics热塑性塑料模 mould for thermoplastics热固性塑料模 mould for thermosets压缩模 compression mould压注模、传递模 transfer mould注射模 injection mould热塑性塑料注射模 injection mould for thermoplastics热固性塑料注射模 injection mould for thermoses定模 stationary mould fixed half动模 movable mould moving half定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate垫块 spacer parallel 支架 ejector housing. mould base leg abrasive grinding 强力injection mould 注塑模injection 注射 in-line-of-draw 直接脱模insert 嵌件inserted die 嵌入式凹模inspection检查,监督installation安装Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡 Void 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2 Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 粒子不密/蜜蜂窝Low impact/tensile etc 物理性能低High flow/filler content etc 流动性/填充…过高Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 玻纤结团Product was rejected due to 产品不能接受因为…High moisture level 高水分Warpage/warped 翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding 打不满Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra …添加多一点…Reduced … content 减少…含量Dropped/reduced … by x％减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT 预计定单量…吨Estimated annual/monthly consumption 预计年/月用量SPC statistic process control品管保证Quality Assurance品管控制Quality control来料检验IQC Incoming quality control巡检IPQC In-process quality control校对calibration动态试验dynamic test环境试验Environmental test非破坏性试验non-destructive test光泽gloss击穿电压(dielectric) breakdown voltage拉伸强度tensile strength冷热骤变试验thermal shock test环境试验炉Environmental chamber盐雾实验salt spray test绝缘电阻测试验仪Insulating resistance meter内应力internal stress疲劳fatigue蠕变creep试样specimen撕裂强度tear strength缩痕shrink mark, sink mark耐久性durability抽样sampling样品数量sample size AQL Acceptable Quality level批量lot size抽样计划sampling plan OC曲线operation curve试验顺序sequence of tests环境温度ambient temperature可焊性solderability阻燃性flame resistance总经理办公室General manager’s office企管部Enterprise management department (EM)行政部Administration department (AD)销售部Sales department (SD)财务部Financial department (FD)技术部Technology department (TD)物控部Production material control department (PMC)生产部Production department(PD)模具部Mold manufacturing department, Tooling manufacturing department (TM)品管部Quality Assurance department (QA)冲压车间Stamp workshop, press workshop注塑车间injection workshop装配车间Assembly workshop模具装配车间Mold and die Assembly workshop金属加工车间metal machine workshop电脉冲车间Electric discharge process workshop线切割车间wire cutting process workshop工磨车间Grinding workshop总经理General manager (GM)副总经理Vice-general manager经理manager董事长president副董事长Vice-president XX部门经理Manager of XX department主任、主管supervisor拉长Line leader组长Foreman, forelady秘书secretary文员clerk操作员operator助理assistant。

注塑常用术语英文表达

1.雾气 Moisture Streaks2.玻纤分配不均 Glass Fiber Streaks3.困气 Gas Trap Effect4.银丝纹 Sliver Marks5.结合线 Weld Line6.水波痕 Water Wave Effect7.黑点 Dark Sport8.顶出印 Visible Ejector Marks9.变形 Deformation During Demolding10.填充不足 Short Filling11.冷料流痕 Cold Slug12.进胶口点不良 Dull Spots Near The Sprue13.喷射痕 Jetting14.表面起层 Flaking Of The Surface Layer15.浮泡 Entrapped Air16.过热变色 Burnt Streaks17.龟裂 Stress Crack18.缩水痕 Sink Marks19.真空气泡 Density Bubble20.披锋 Flash21.擦伤印 Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大 Over dimension23尺寸过小 Under dimension24 翘曲 Warpage/warped25 收缩 Shrinkage/shrink26 缩影 Sink marks27 打不满 Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush 直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床V ertical driller超声波清洗机Ultrasonic clearing machine 精品文档word文档可以编辑！谢谢下载！。

注塑专业中英文术语

注塑专业中英文术语注塑机参数 Injection Machine Parameter1，注塑机规格参数 Injection Machine Specification①锁紧类型 clamp typea．油缸— hydraulic b．肘杆式— toggle②垂直注塑机导柱间距— tie bar vertical clearance③水平注塑机导柱间距— tie bar horizontal clearance④台板尺寸— platen dim.⑤最小 / 最大模厚— mold height Min./ Max., Min. / Max. mold thickness⑥最小 / 最大注塑机开档— open day light Min. / Max.⑦锁紧行程—clamp stroke ⑧锁紧力— clamping force⑨顶出行程—ejector stroke ⑩顶出力— ejector force2，试模工艺参数 Molding Process Parameter, machine setting①时间 Timer（TM）, seca, 注塑（充填）时间— filling time, injection timeb, 冷却时间— cooling time c, 补缩时间— packing timed, 保压时间— holding time e, 成型周期— cycle time②速率、速度 Velocity, %、speed, in/seca, 注塑（充填）速度— injection speedb, 保压速率— hold pressure velocityc, 螺杆转速— screw rotation speed③压力 Pressure（Prs.）, psia, 注塑压力— injection pressure b, 保压压力— hold pressure c, 回压（背压）— back pressure④温度 Temperature（Temp.）, °Fa, 注塑机喷嘴温度— nozzle temp.b, 料筒前段、中段、后段温度—barrel front、middle、rear temp.c, 模温— mould temp. d, 料温— purged resin melt temp.e, 空射料温— air shot melt temp.产品几何 Geometry1．点— point 2．线（边）— line, edge3．面 faceA 侧面— sideB 表面— surfaceC 外观面— appearance surface4．壁厚— wall thickness, stock thickness5．加强筋（骨位）— rib 6．孔— hole7．细长的槽— slot 8．柱位— boss9．角—cornerA 圆角— filletB 倒角— chamferC 尖角— sharp corner10．斜度— angle, taper 11. 凹槽—recess , groove一．分模信息 Splitting1．分型线— parting line (P/L), splitting line2．主分模方向— main direction, line of draw3．浇口设定— gating二．产品标识 Part Identification1．产品名称— part name (P/N)2．产品编号+版本号— part number + revision (Rev.)3．型腔号—cavity number 4．材料标记—material symbol 5．模具编号— mold number (no.) 6．日期印—date code 7．循环印— cycling code 8．公司标志—company logo 三．技术要求 Specification (Special Requirement)1．项目启动表 Kick-off sheet5）项目启动日期— kick off date, start date6）项目完成日期— due date, lead time7）内模件用钢— tool steel8）型腔数量— number of cavities9）数据文件编号— data file no.10）注塑材料— resin, plastic, raw material11）收缩率— shrink, shrinkage, shrink factor12）注塑机吨位—molding machine size, injection machine size13）成型周期— cycle time14）型腔光洁度— cavity polish15）型芯光洁度— core polish16）皮纹（晒纹）— texture, grain17）拔模斜度— draft angle, removal taper18）注塑件颜色及光泽— molded color & gloss19）模具加工地— manufacturing facility20）热流道供应商—manifold manufacturer, manifold supplier21）浇口位置— gate location / position22）浇口类型— gate type23）产品标识— stamp information, part identification24）特殊要求— special instructions2．产品质量及外观要求Part Quality & Appearance Requirement1）尺寸及公差 Dimension & Tolerance①重要尺寸— critical dimension, important dim., key dim.②理论尺寸—nominal dimension ③实际尺寸—actual dimension⑤公差带—tolerance range ⑥尺寸超差— dimension deviation⑧拒绝（不合格）— reject, refuse, obsolete, NG⑨让步接受— concession, special admit2）产品缺陷（常见的）Defects (normal)①缩水—sink mark, shrinkage ②飞边，毛边— flash, burr③段差—mismatch discrepancy ④银丝纹，蛇纹—snake marks, streak⑤弯曲，变形— warpage, distortion⑥打不饱（缺料）—short shot ⑦熔接线— weld line⑧多胶—unwanted plastic ⑨拉伤—damage3．产品外观 Part Appearance①产品颜色—part color ②产品光泽— gloss③皮纹粒度— grain4．常用词汇、词组及短语 Normal Word, Short Sentence1）单边— per side 2）双边— both sides3）加入，添加—add, incorporate 4）去除，取消—remove, cancel5）满足…的要求，符合，与…要求一致—according to, conform to, satisfy, meet6）要求，需要— require, need, demand7）确认—be approved, agreed by …8）允许— permit, allow 9）在…范围之内— within10）不可以，不允许，禁止— free from, prevent, avoid11）除非有另指—… unless otherwise specified12）或少于—…or less13）自动化运作— automatic operation 14）未注尺寸（详细形状）见三维造型Non dimensioned contour(detailed shape) see 3D model.15）分型线上的飞边（披缝）或段差应小于…Burrs or discrepancy on the P/L shall be … or less.注塑过程专业术语以及分析1, 热注射成型 thermoplastic injection molding2. 控制面板 control plat 对设备参数控制的简易操作平台3 显示器 pro-face 显示设备必要信息的屏幕4 安全门 safe door 防止事故发生,增大安全系数的保护装置门5 注射座 Injection blend 注射成型机组成部件,支撑并协助注射的金属平台6 螺杆 screw 起旋转计量作用的螺纹状部件.是成型机的核心机械件7 料膛fabbrel 树脂预塑的炮膛状部件,和螺杆配合俎件质量要求较高8 加热圈 heater 围绕在料膛周围,起迅速并均匀加热作用的片状加热器9 喷嘴 nozzle 连接注射成型机料筒与模具浇口套接触的像针头状的组件10 定模板 plam 可固定模具在成型机上的铁板,是成型机的一部分11 动模板 moving plam成型机曲臂连接板,使模具固定在成型机上做开合模运动的动模板12 成型机顶杆ejector pin 连接到模具上控制模具顶杆顶出或回退作用的连接杆13 手动操作 man 只能手动单一步骤状态操作14 半自动操作 sengle man 可半自动状态操作15 全自动操作 auto 根据设置的程序在全自动状态动作16 料膛清洗 purge 一般用PE料做**动作来清除或淡化料膛内物料或颜色17 上料机loader 在料杯树脂不足在传感器监控下吸取储备树脂的成型辅助设备18 温调机，控制模具温度,保持在设定温度以内的温度控制设备19 参数监控画面，对设备具体参数设定的画面,一般配有图表20 生产管理画面product menut 在全自动生产状态下对产品质量和数量控制的页面21 模板控制画面 plam control 模板动作状态控制页面22 顶出控制画面 ejector control 顶出动作状态控制画面23 加热管理画面 heat control 材料加热控制画面24 注射速度画面 speed control 注射过程中对速度控制的画面25 注射压力画面fulling pressure control 注射过程中注射压力控制画面26 保压控制画面 packing pressure control注射后保持设定压力提高制品质量的控制画面27 计量控制画面 excit control 计量尺寸和相关参数控制画面28 报警显示画面 alarm view 设备动作异常或监控报警预览29 最大高度 maximum daylight 成型机模板打开的最大尺寸30 最小高度minimum daylight 能满足成型机性能的最小模具厚度31 锁模力clamping force成型过程中为保证动，定模相互紧密配合而需施加的在模具上的力32 锁模系统 clamping system 模板控制系统,注塑机上系统的一部分33 控制系统control system 计算机通过检测、处理信息并重新输入计算机进行控制相关参数34抽芯距core-pulling distance 将侧型心抽至不防碍制品脱落的滑块滑动的距离35 抽芯力 core-pulling force 从模内的成型塑件中，抽**侧型心所需要的力36 生产周期Cycle time 生产每个制品的时间或是单位时间内生产制品的个数37 液压系统 hydraulic system 液压动力注射机上的压力系统38 短射 short shot 由于一次注射压力不足或速度偏低引起的浇不足现象39 ** jetting 材料水份超标,结构不良引起的表面气泡等不良现象40 白化，制品破坏前变形引起的颜色差异41 缩痕 shrinkage 热熔体在收缩情况下表面会形成凸凹状现象的统称42 收缩差异 asymmetric shrinkage 制品厚度不均匀或分子排列不同引起的不均匀收缩43 熔接线 lines 两股或多股熔体结合位置形成的线状痕迹44 亮线 color change 一种有明亮痕迹的注塑成型缺陷，一般为线状少为带状45 冷熔接 Cold welding 低温区域的熔接，多见于冲填结束，不同塑料熔前交汇造成46 困气air traps 又称包气,熔体流动将气体堵住或包住不能及时排出47 烧伤 burn 填充时模具内部气体不能迅速排出产生压缩高温,导致制品局部变色48黑斑 black specks 注射成型过程中因高温或树脂分解等原因引起的黑色不良现象49 料纹black streads树脂在模具腔内流动时由于层流因素引起的外观不良现象51 烧焦 burn marks 因高温引起的成型缺陷的一种52 色差discoloration制品本身颜色有其他杂质颜色混入形成的不良现象53 脆化brittleness 成型缺陷（因树脂性质发生变化引起的脆化或者破裂）54 蠕变 Creep高聚物在恒定温度和应力下，长度随时间延长而逐步深长的现象55 位移 Displacement熔体内部压力差引起高压部份向低压部分推移现象,可产生层次感56 分层表面剥离delamination同一树脂或不同树脂发生层流后产生的现象57 三角洲效应 delta effect局部温度差58 方向收缩 diectional shrinkage由大分子链排列引起的具有方向特性的收缩59 尺寸变化dimensional variation生产出的制品在不同的环境下都会产生尺寸的变化60 尺寸稳定性 dimensional stability制品尺寸的稳定性和一致性61 密度 Density 单位体积的质量62 翘曲 warpage 有多种原因引起的变形现象,如收缩翘曲,配向翘曲等63 变形 distortion 产品在内应力或外力的作用下产生的尺寸变化以及形状变化64 迟滞 hesitation 熔体的某一部份发生停止流动或极缓慢流动的现象65 垂直于流动方向的收缩 cross-flow shrinkage 发生在垂直于熔体流动方向上的收缩66 热变形温度 deflection temperature热力的作用下，塑料可以发生变形的温度67 脱模demolding 保压后制品在模具内部成型完毕脱离模具的现象68 脱模斜度 draft 方便成型制品脱离模具而设计的角度69 脱模困难ejection difficulties 成型制品不容易脱离模具的现象70 内应力 internal stress 残留在制品内部因各种原因产生的应力71 长链高分子 long chain macromolecules 很多小分子连接而成的具有较大质量的长分子连72 凝固层比例 frozen layer fraction 熔体在模具内冷却状态之一的数学表示方法73 取出 removal 成型后制品拿出的过程74 粗加工rough machining 毛坯加工或留有大量余量的待加工品75 伺服马达 servomotor 配合CPU工作的马达76 工序 workstage 完成一个组件或产品经过的步骤77 塑料件 plastic parts 以塑料为原料生产的制品78 注射模 injection mould 通过注射方式成型的模具79 斜销 angle pin / finger cam 倾斜于分型面、随模具的开闭产生相对运动的圆柱零件80 斜滑块 angled-lift / splits 斜向镶块或滑动的镶块81 悬臂搭扣连接 cantilever snap joints组合方式之一82 模套 chase / bolster / frame 使镶件或拼块定位并紧固在一起的框套形结构零件83 型芯 Core 成型模具内表面突起的组件84 支架 ejector housing / mould base leg 使动模能固定在压机或注塑机上的L型垫块85 推块 ejector pad 在腔内起部分成型作用，并在开模时把塑件从型腔内推出的零件86 推杆 ejector pin 用于推出塑件或浇注系统凝料的杆件87 推板ejector plate 支撑推出和复位零件，直接传递机床推出力的板件88 复位杆 push-pack pin 借助模具的闭合动作，强制推出机构复位的杆件89 浇口尺寸 Gate dimensions(sizes) 浇口的相关尺寸90 直接浇口 direct gate ; sprue gate 熔融塑料经主流道直接进入型腔的进料方式91 盘式浇口 disk gate 沿塑料件内圆周扩展进料的浇口92 侧浇口 edge gate 设置在模具的分型处从塑件的内或外侧进料的方式93 扇形浇口 fan gate 从分流道道型腔方向的宽度逐渐增加的呈扇型的浇口94 浇口镶块 gating insert 浇口以镶块的形式存在95 圆柱头推杆 ejector pin with cylindrical head 头部形状是圆柱型形推杆96 扁顶杆 flat ejector pin 工作截面为矩形的顶杆97 连接推杆 ejector tie rod 连接推件板与推杆固定板，传递推力的杆件98 导套 guide bush 与导柱相配合，用于初步确定模具99 导柱 guide pillar 起导向作用的部件，一般为圆柱体100 浇口 gate 连接分流道合型腔的进料通道101 浇口长度 gate length 浇口的长度102 浇口位置Gate location 树脂流入模腔的点相对整体模腔的位置103 嵌件insert 成型中埋入或随后压入塑件中的金属或其他材料的部件104 楔紧块 heel lock 带有楔角,用于合模时楔紧滑块的零件105 凹模 cavity plate 成型塑件外表面的凹壮零件(包括零件的内腔和实体两部分)106 凹模拼块 cavity splits 母模中的镶件拼块107 定模座板 fixed clamp plate 使定模固定在注塑机的固定工作台面上的板件108 顶出系统设计 ejection system design顶出制品机构的类型109 顶出时间ejection time 制品脱离模具可安全取出的时间110 推板导套ejector bushing 与导柱滑配合，用于推出机构导向的圆柱形零件成型工艺 Molding technique procedureA 成型工艺 Section 1 molding technique.1.成型工艺参数类型 Sorts of molding parameter.(1). 注塑参数 Injection parameter.a.注射量 Injection rate.b.计量行程Screw back positionc.余料量Cushiond.防诞量Sucking back ratee.螺杆转速Screw speedf.塑化量Plastic0 rateg.预塑背压Screw backpressureh.注射压力和保压压力Injection pressure and holding pressurei.注射速度Injection speed(2)合模参数Clamping parametera.合模力Clamping forceb.合模速度Clamping speedc.合模行程.Clamping stroked.开模力Opening forcee.开模速度Opening speedf.开模行程Opening positiong.顶出压力Ejector advance pressure h.顶出速度Ejector advance speedi.顶出行程Ejector advance position2.温控参数Temperature parametera.烘料温度Dry resin material temperatureb.料向与喷嘴温度Cylinder temperature and nozzle temperaturec.模具温度Mold temperatured.油温Oil temperature3.成型周期Molding cyclea.循环周期Cycle timeb.冷却时间Cool timec.注射时间Injection timed.保压时间Holding pressure timee.塑化时间Plant timef.顶出及停留时间Knocking out and delay timeg.低压保护时间Mold protect time成型工艺参数的设定须根据产品的不同设置.Molding technique parameter setting differs depending on type of product 成型条件设定 Molding parameter Setting按成型步骤:可分为开锁模,加热,**,顶出四个过程.Molding steps: mold opening/closing, heating injection and knocking out.开锁模条件:Mold opening parameter: 快速段中速度High-speed mid-speed低压高压速度Low pressure high pressure speed锁模条件设定:Mold closing parameter setting1锁模一般分: 快速→中速→低压→高压Mold closing: high-speed →low-speed →low pressure→ high pressure。

注塑模具专业英语

Injection Mold Technical Terms（一）模具专业基本用词Professional Terms1．塑料— plastic, resin2．样件— sample3．钢料— steel4．注塑机— injection machine, press5．产品— part, product, moulding6．模具— mold, mould, toolA 简易模（样板模）— prototype moldB 量产用模具— production mold 7．三维造型（数模）—3D model, 3D data8．二维产品图— 2D part drawing9．设计— design10．制造— manufacture, build up, construction, fabrication, make11．检验— check, inspection12．测量— measure, inspection13．修改— change, modify, correction14．工程更改— engineer change15．质量— quality16．数量— quantity17．基准— datum, reference（二）如何解析2D 产品图？How to read 2D part drawing?一．产品几何Geometry1．点— point2．线（边）— line, edge3．面faceA 侧面— sideB 表面— surfaceC 外观面— appearance surface 4．壁厚— wall thickness, stock thickness5．加强筋（骨位）— rib6．孔— hole7．细长的槽— slot8．柱位— boss9．角— cornerA 圆角— filletB 倒角— chamferC 尖角— sharp corner 10．斜度— angle, taper11. 凹槽—recess , groove二. 分模信息Splitting1．分型线— parting line (P/L), splitting line2．主分模方向— main direction, line of draw3．浇口设定— gating一．产品标识Part Identification1．产品名称— part name (P/N)2．产品编号+版本号— part number + revision (Rev.)3．型腔号— cavity number4．材料标记— material symbol5．模具编号— mold number (no.)6．日期印— dating insert, date code7．循环印— cycling code8．公司标志— company logo二. 技术要求Specification (Special Requirement)1．项目启动表Kick-off sheet1）项目名称— program name, project name2）产品名称— part name, product name, part description3）产品编号— part number (P/N)4）客户模号— customer mold no.5）项目启动日期— kick off date, start date6）项目完成日期— due date, lead time7）内模件用钢— tool steel8）型腔数量— number of cavities9）数据文件编号— data file no.10）注塑材料— resin, plastic, raw material11）收缩率— shrink, shrinkage, shrink factor12）注塑机吨位— molding machine size, injection machine size 13）成型周期— cycle time14）型腔光洁度— cavity polish15）型芯光洁度— core polish16）皮纹（晒纹）— texture, grain17）拔模斜度— draft angle, removal taper18）注塑件颜色及光泽— molded color & gloss19）模具加工地— manufacturing facility20）热流道供应商— manifold manufacturer, manifold supplier 21）浇口位置— gate location / position22）浇口类型— gate type产品标识— stamp information, part identification特殊要求— special instructions1．产品质量及外观要求Part Quality & Appearance Requirement 1）尺寸及公差Dimension & Tolerance①重要尺寸— critical dimension, important dim., key dim.②理论尺寸— nominal dimension③实际尺寸— actual dimension④公差— tolerance⑤公差带— tolerance range⑥尺寸超差— dimension deviation⑦接受（合格）— accept, OK⑧拒绝（不合格）— reject, refuse, obsolete, NG⑨让步接受— concession, special admit⑩返工— re-work2）产品缺陷（常见的）Defects (normal)①缩水— sink mark, shrinkage②飞边，毛边— flash, burr③段差— mismatch discrepancy④银丝纹，蛇纹— snake marks, streak⑤弯曲，变形— warpage, distortion⑥打不饱（缺料）— short shot⑦熔接线— weld line⑧多胶— unwanted plastic⑨拉伤—damage2．产品外观Part Appearance①产品颜色— part color②产品光泽— gloss③皮纹粒度— grain3．常用词汇、词组及短语Normal Word, Short Sentence1）单边— per side2）双边— both sides3）加入，添加— add, incorporate4）去除，取消— remove, cancel5）满足…的要求，符合，与…要求一致— according to, conform to, satisfy, meet 6）要求，需要— require, need, demand7）确认—be approved, agreed by …8）允许— permit, allow1）在…范围之内— within2）不可以，不允许，禁止— free from, prevent, avoid3）…，除非有另指—… unless otherwise specified4）…或少于—…or less5）自动化运作— automatic operation6）未注尺寸（详细形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.7）分型线上的飞边（披缝）或段差应小于…Burrs o r discrepancy on the P/L shall be … or less.标题栏Title Block1．产品名称— part name2．图纸编号+ 版本号（索引号）— drawing no. + level (index)3．一般公差— general tolerance（三）如何阅读制模标准？How to read tooling standard?一．模具结构术语Mold Construction TermsA．模架Mold Base1．模架量化特征Measurement Feature①长X 宽X 高— Length X Width X Height②模具高度尺寸（模厚）— stack height of mould③模具重量— total weight of mould, mould thickness2．定模底板— front plate, top clamping plate, clamp plate, clamping plate3．定模板— cavity plate, fixed mould plate, A – plate4．动模板— core plate, moving mould plate, B – plate5．支撑板— support plate, backing plate6．间隔板,方铁— support blocks, rails, risers, spacer block7．顶杆固定板— retaining plate, ejector retaining plate8．顶板— ejector plate，bottom clamping plate9．动模底板— back plate10．导柱— guide pillar, leader pin, guide pin11．导套— guide bush, leader pin bush12．复位杆— return pin, push-back pin13．弹簧— spring14．撑头— support pillar15．顶针板导柱、导套— ejection guide pin / bush16．垃圾钉— stop pin, stop button17．模脚— standing-off pillars18．标牌— plaque scutcheonB．成型零部件moulding components1．型芯— core insert2．型腔— cavity insert3．镶针— core pin4．镶块— sub-insert, split5．滑块— slide, sliding split6．斜顶— lifter, angled-lift split, loose coreA 斜顶头— lifter headB 斜顶杆— lifter rod, lifter shaft 7．成型顶杆— moulding face pin, form pinC．浇注系统Feed System1．塑料Mouldinga．主流道— sprueb．分流道runner①主分流道— main runner ②二级分流道— branch runner 分流道断面形状cross-sectional shape of runner①圆形— full round②半圆形— semicircular③梯形—trapezoidalc．浇口gate常用浇口形式normal gate type :①边缘浇口（J型浇口）— edge gate, J – gate②侧浇口— side gate③潜伏式浇口— sub-gate, subsurface gate, submarine gate, cashew gate④潜伏式二次浇口(隧道式浇口) — tunnel gate onto feeder post⑤点浇口— pin gate⑥直接浇口(主流道型浇口) — sprue gate, direct gate⑦护耳式浇口— tab gated．模腔— impressione．冷料井— cold slug wellf．热流道— hot runner2．模具零件mold componentsa．定位圈— locating ring, location ring, register ringb．浇口套— sprue bushc．挡圈— stop ringd．浇口镶块— gate inserte．热流道板— manifoldf．热嘴— hot drop\hot sprue分型面及其锁紧、排气Parting Surface, inter-locking & venting1．分型线— parting line ( P/L )2．镶拼线— bodyline, joint line3．平/ 不平的分型面— flat / non – flat parting surface4．封胶面— shut off surfaces, seal-off surfaces5．擦穿位— shut off6．碰穿位— kiss-off7．管位— parting line lock8．分型面的释放(避空) — relief of parting surface9．分型面的平衡— balancing of parting surface10．锁紧角度— locking angle11．锁紧力— clamping force12．锁模块— safety strap13．精定位— Interlock, die lock14．困气— air trap15．排气槽— vent, vent slotE．滑块机构Slide1．驱动Actuation①斜导柱— angle pin, horn pin, cam pin②弹簧— spring③油缸— hydraulic cylinder2．制动Detention①滑块固定器— slide retainer②弹簧制动器— spring-loaded detention (plunger)③挡钉、挡板— stop pin, stop plate, slide stop3．导轨— gib, guide strip4．锁紧块（楔紧块）— heel block, locking heel, wedge block, chase block 5．耐磨片— wear plate, wear strip6．压板— retainer, gib7．螺钉— screw8．定位销— dowel pinF．斜顶机构Lifter1．斜顶头— lifter head2．斜顶杆— lifter rod, lifter shaft3．开口销— split pin4．固定板（压板）— retainer plate5．耐磨片— wear plate1．铜导套— bronze bushing2．衬套— spacer3．导轨— L – gib4．滑动块— slideG．顶出系统Ejection System1．基本词汇Basic Word①顶出行程— ejection stroke②模具开档— daylight③粘模— stick④产品脱模— part is push off from, clear part of mould, separation of part 2．顶板机构Ejector plate assembly①顶板— ejector plate②顶板固定板— retaining plate③推板— stripper plate④推板导柱— ejector guide pin⑤推板导套— ejector guide bush⑥撑头— support pillar3．复位机构Return System①复位杆（回程杆）— return pin, push – back pin②垃圾钉— stop pin, stop button③压簧— compressed spring④碟簧—a stack of ―Belleville‖ washers⑤早复位机构— early return system⑥强制复位机构— positive return system4．顶出方法Ejection Techniques1）顶杆顶出— pin ejection2）顶管顶出— sleeve ejection3）顶块顶出— bar ejection4）扁顶顶出— blade ejection5）顶板顶出— stripper ejection6）油缸顶出— hydraulic ejection7）气顶— air ejection8）阀门顶出— valve ejection5．顶出元件Ejection Elements1）拉料杆— sprue puller, sucker pin2）顶杆— ejector pin3）阶梯式顶杆— stepped ejector pin1）顶管— ejection sleeve, sleeve2）扁顶— ejector blade, slabbed off ejector pin3）顶块— stripper bar4）顶环— stripper ring5）推板— stripper plate6）加速顶— accelerated ejection1．顶出辅助机构Supplementary operating system1）弹簧柱塞器— spring – loaded plunger2）弹珠定位器— ball catch system3）插销式锁扣— Latch – lock4）尼龙拉杆装置— friction puller device2．电器元件Electric Components1）压力传感器— pressure transducer2）限位开关— limit switchF．冷却系统Cooling System1．基本词汇Basic Word1）温差— temperature variation2）水孔（水道）— waterlines, water-ways, flow-way, channel3）水路— cooling circuit4）水路示意图— water schematic, schematic circuit5）冷却液— coolant, coolant fluid6）内连接— interconnect7）外连接— external connection8）出口、入口— outlet、inlet9）漏水— water leakage2．水路分布Circuits1）阶梯式水路— stepped system2）分隔板水路— baffled hole system3）斜孔式水路— angled hole system3．水路元件Components1）闷头（螺塞、止水栓）—（threadless）brass pressure plug : female plug & male 2）隔水片— baffle3）密封圈— O – ring4）快插水路接头— quick disconnect fitting, quick connection adaptor5）弯头— elbow6）偶合器（连接器、接头）— adaptor (including a plug & a socket)7）橡皮管— rubber hose1）分水板,集水块— water manifoldG．螺纹、螺纹孔& 螺钉Thread, thread hole & screw1．螺纹— thread2．管螺纹— pipe thread3．螺纹孔— screw hole, tapped hole4．起吊孔— handling hole, jack screw hole, eye bolt hole5．螺钉— screw6．内六角螺钉— socket headed cap screw （s.h.c.s.）7．沉头螺钉— flat headed cap screw （f.h.c.s）8．螺栓— bolt9．螺母— nut10．锁紧螺母— locknut11．螺纹标准Thread Standard①公制标准— Metric②英制标准— Imperial③英制管螺纹标准— British Standard Pipe thread （BSP）④美制管螺纹标准— NPT⑤美制粗螺纹标准— United Coarse thread （UNC）⑥美制细螺纹标准— United Fine thread （UNF）H．润滑Lubrication1．润滑槽— grease groove2．加油管— grease line3．油杯— lubrication fittingI. 测量仪器Measuring Instruments1．游标卡尺— vernier caliper2．千分尺— micrometer3．高度规— height gauge4．刻度规— dial gauge5．三坐标测量仪（三次元）— Coordinate Measure Machine（CMM）6．塞规— pin gauge7．圆角量规— radii gauge8．轮廓投影机—profile projectorJ．注塑机参数Injection Machine Parameter1．注塑机规格参数Injection Machine Specification①锁紧类型clamp typea．油缸— hydraulic b．肘杆式— toggle②垂直注塑机导柱间距— tie bar vertical clearance③水平注塑机导柱间距— tie bar horizontal clearance④台板尺寸— platen dim.⑤最小/ 最大模厚— mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档— open daylight Min. / Max.⑦锁紧行程— clamp stroke⑧锁紧力— clamping force⑨顶出行程— ejector stroke⑩顶出力— ejector force。

注塑机英语专业术语

Clamping Cylinder Piston Piston Bar Seal “O” Ring Mold Adjust Motor Big Gear Small Gear Bearing Toggle Toggle Pin Front(Fixed) Platen Moving Platen Rear Platen Cross Support platen Tie Bar Front Tie Bar Nut Rear Tie Bar Nut Mold Adjust Sensor (Approach Switch) Electro Motor bracket Oil Pump Coupling(Motor) Coupling(Pump) buffer Lubrication Pump Appendix Unit screw head , check ring ,ring set
变频器液压合模安全保护液压抽芯装置液压/电动旋转脱模装置公母模吹气阀玻管分水器图态继电器加长喷嘴，弹簧喷嘴，液压开启喷嘴旁路回油过滤器自动安全门模具压板磁力架各类注射模具气体辅助注射装置塑料制品取出机械手及传送带除湿干燥机模温控制器干燥料斗及真空输料各种相关设备及完整的生产流水线螺杆直径理论注射容量注射压力合模力移模行程拉杆内距最大模厚最小模厚顶出行程顶出力顶出杆根数最大油泵压力油泵马达
hopper capacity oil tank capacity machine dimension machine weight robot screen voltage changement core pulling mold hanger cool water valve air blaster/air blow transducer air breaker safety edge switch heater band thermo couple oil seal vane pump directional valve proportional valve plasticizing hydraulic motor orbital hydraulic motor electric motor auxiliary equipment component plastics dryer vacuum auto loader mold temp controller industrial chiller dehumidifier crusher vertical color mixer safety carpet

注塑机必备英语

注塑机各部件的中英文名称和作用Injection machine 啤机Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力non-return valve 止回阀shear 剪切opening stroke开模行程Injection pressure 射胶压力back pressure 背压nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要设备Reserve pressure packing pressure保压mold trial 试模 shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度booster time 增压时间Compression ratio 压缩比mold close time 合模时间Resin 胶料Plasticization 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降解，软化regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重Elongation 延伸率density 密度melting point 熔点Polystyrene 聚苯乙烯（PS）Styrene 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethylene 聚乙烯glass fiber 玻纤Condensation 凝固，浓缩crystalline resin结晶形塑料compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子nner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 流道:runner 热流道：hot runner,hot manifold 热嘴冷流道:hot sprue/cold runner 唧嘴直流:direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头： connector plug插座： connector socket密封/封料： seal运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 模具零件： mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板： support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针： ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode塑料成形模具 mould for plastics热塑性塑料模 mould for thermoplastics热固性塑料模 mould for thermosets压缩模 compression mould压注模、传递模 transfer mould注射模 injection mould热塑性塑料注射模 injection mould for thermoplastics热固性塑料注射模 injection mould for thermoses定模 stationary mould fixed half动模 movable mould moving half定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate垫块 spacer parallel 支架 ejector housing. mould base leg abrasive grinding 强力injection mould 注塑模injection 注射 in-line-of-draw 直接脱模insert 嵌件inserted die 嵌入式凹模inspection检查,监督installation安装Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡 Void 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2 Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 粒子不密/蜜蜂窝Low impact/tensile etc 物理性能低High flow/filler content etc 流动性/填充…过高Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 玻纤结团Product was rejected due to 产品不能接受因为…High moisture level 高水分Warpage/warped 翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding 打不满Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra …添加多一点…Reduced … content 减少…含量Dropped/reduced … by x％减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT 预计定单量…吨Estimated annual/monthly consumption 预计年/月用量SPC statistic process control品管保证Quality Assurance品管控制Quality control来料检验IQC Incoming quality control巡检IPQC In-process quality control校对calibration动态试验dynamic test环境试验Environmental test非破坏性试验non-destructive test光泽gloss击穿电压(dielectric) breakdown voltage拉伸强度tensile strength冷热骤变试验thermal shock test环境试验炉Environmental chamber盐雾实验salt spray test绝缘电阻测试验仪Insulating resistance meter内应力internal stress疲劳fatigue蠕变creep试样specimen撕裂强度tear strength缩痕shrink mark, sink mark耐久性durability抽样sampling样品数量sample size AQL Acceptable Quality level批量lot size抽样计划sampling plan OC曲线operation curve试验顺序sequence of tests环境温度ambient temperature可焊性solderability阻燃性flame resistance总经理办公室General manager’s office企管部Enterprise management department (EM)行政部Administration department (AD)销售部Sales department (SD)财务部Financial department (FD)技术部Technology department (TD)物控部Production material control department (PMC)生产部Production department(PD)模具部Mold manufacturing department, Tooling manufacturing department (TM)品管部Quality Assurance department (QA)冲压车间Stamp workshop, press workshop注塑车间injection workshop装配车间Assembly workshop模具装配车间Mold and die Assembly workshop金属加工车间metal machine workshop电脉冲车间Electric discharge process workshop线切割车间wire cutting process workshop工磨车间Grinding workshop总经理General manager (GM)副总经理Vice-general manager经理manager董事长president副董事长Vice-president XX部门经理Manager of XX department主任、主管supervisor拉长Line leader组长Foreman, forelady秘书secretary文员clerk操作员operator助理assistant。

注塑专业英语

Surface Appearance外观Glossiness/gloss finish光洁度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡V oid孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersion分散不好FR/PTFE …agglomerates etc阻燃剂/PTFE…结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充…过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to产品不能接受因为…High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in extra …添加多一点…Reduced … content减少…含量Dr opped/reduced … by x％减少…含量…％Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption 预计年/月用量air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模？die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧？goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口？roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量三、模具塑料模具mould of plastics 注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate 底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine一、组织机构及职位二、X X电子有限公司XX Electronics CO., Ltd三、总经理办公室General manager’s office四、企管部Enterprise management department (EM)五、行政部Administration department (AD)六、销售部Sales department (SD)七、财务部Financial department (FD)八、技术部Technology department (TD)九、物控部Production material control department(PMC)十、生产部Production department(PD)十一、模具部Mold manufacturing department, Tooling manufacturing department (TM)十二、品管部Quality Assurance department (QA) 十三、冲压车间Stamp workshop, press workshop 十四、注塑车间injection workshop十五、装配车间Assembly workshop十六、模具装配车间Mold and die Assembly workshop 十七、金属加工车间metal machine workshop十八、电脉冲车间Electric discharge process workshop十九、线切割车间wire cutting process workshop 二十、工磨车间Grinding workshop二十一、总经理General manager (GM)二十二、副总经理Vice-general manager二十三、经理manager二十四、董事长president二十五、副董事长Vice-president二十六、XX部门经理Manager of XX department二十七、主任、主管supervisor二十八、拉长Line leader二十九、组长Foreman, forelady三十、秘书secretary三十一、文员clerk三十二、操作员operator三十三、助理assistant六．物控保质期shelf lifeABC分类法ABC Classification反常需求Abnormal Demand措施信息Action Message活动报告标志Action-report-flag基于活动的成本核算Activity-based Costing (ABC) 实际能力Actual Capacity实际成本Actual Costs调整现有库存量Adjust-on-hand已分配量Allocation替代工序Alternative Routine装配订单Assembly Order装配零件表Assembly Parts List装配Assembly计划自动重排Automatic Rescheduling可达到库存Available Inventory可用材料Available Material达到库存Available Stock可利用工时Available Work可签约量Available-to-promise平均库存Average Inventory欠交订单Back Order倒序计划Back Scheduling倒冲法Back flush未完成订单Backlog现有库存余额Balance-on-hand Inventory批号Batch Number批量生产Batch Production标杆瞄准Benchmarking工时清单Bill of Labor提货单Bill of Lading物料清单Bill of Material分库Branch Warehouse经营规划Business Plan采购员Buyer能力管理Capacity Management能力需求计划Capacity Requirements Planning (CRP) 保管费率Carrying Cost Rate保管费Carrying Cost单元式制造Cellular Manufacturing修改批量日期Change Lot Date修改工序Change Route修改产品结构Change Structure检查点Check Point闭环物料需求计划Closed Loop MRP通用工序标识Common Route ID计算机集成制造Computer-integrated Manufacturing (CIM)配置代码Configuration Code约束管理/约束理论Constraints Management/Theory of Constraints (TOC)依成本的材料清单Costed Bill of Material急需零件Critical Part累计提前期Cumulative Lead Time现有运转时间Current Run Hour现有运转数量Current Run Quantity周期盘点Cycle Counting调整日期Date Adjust有效日期Date Available修改日期Date Changed结束日期Date Closed截止日期Date Due生产日期Date in Produced库存调整日期Date Inventory Adjust作废日期D ate Obsolete收到日期Date Received交付日期Date Released需求日期Date Required发货日期Date to Pull空负荷Dead Load需求管理Demand Management需求Demand实际能力Demonstrated Capacity非独立需求Dependent Demand直接增减库存处理法Direct-deduct Inventory Transaction Processing发料单Disbursement List派工单Dispatch List分销资源计划Distribution Resource Planning (DRP) 鼓－缓冲－绳子Drum-buffer-rope经济订货批量Economic Order Quantity (EOQ)工程变更生效日期Engineering Change Effect Date工程变更生效单Engineering Change Effect Work Order工程停止日期Engineering Stop Date例外控制Exception Control呆滞材料分析Excess Material Analysis急送代码Expedite Code加工订单Fabrication Order补足欠交Fill Backorder总装提前期Final Assembly Lead Time 确认的计划订单Firm Planned Order固定订货批量F ixed Order Quantity集中预测Focus Forecasting完全跟踪Full Pegging通用生产管理原则Generally Accepted Manufacturing Practices毛需求Gross Requirements在制品库存In Process Inventory独立需求Independent Demand投入/产出控制Input/ Output Control检验标识Inspection ID厂际需求Interplant Demand库存周转率Inventory Carry Rate仓库库位类型Inventory Location Type库存周转次数Inventory Turnover发送订单Issue Order项目记录Item Record物料项目Item加工车间Job Shop准时制生产Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time层Level负荷量Load Leveling负荷报告Load Report负荷Load仓位代码Location Code仓位备注Location Remarks仓位状况Location Status按需订货Lot for Lot批量标识Lot ID批量编号Lot Number批量Lot Size低位码Low Level Code机器能力Machine Capacity机器加载Machine Loading外购或自制决策Make or Buy Decision面向订单生产的产品Make-to-order Product面向库存生产的产品Make-to-stock Product制造周期时间Manufacturing Cycle Time制造资源计划Manufacturing Resource Planning (MRP II)主生产计划Master Production Schedule (MPS)物料成本Material Cost物料发送和接收Material Issues and Receipts物料需求计划Material Requirements Planning (MRP) 登陆标志MPS Book Flag MPS多重仓位Multiple Location净改变式MRP N et Change MRP净需求Net Requirements新仓位New Location新组件New Parent新仓库New Warehouse不活动报告No Action Report现有库存量On-hand Balance未结订单Open Order订单输入Order Entry订货点Order Point订货方针Order Policy订货承诺Order Promising订货备注Order Remarks双亲Parent零件清单Part Bills零件批次Part Lot零件编号Part Number零件Part反查Pegging领料单Picking List领料/提货Picking计划订单Planned Order后减库存处理法Post-deduct Inventory Transaction Processing前减库存处理法Pre-deduct Inventory Transaction Processing发票价格Price Invoice采购订单价格Price Purchase Order优先计划Priority Planning产品控制Product Control产品线Production Line生产规划编制Production Planning产品率Production Rate产品结构树Production Tree预计可用库存Projected Available Balance采购订单跟踪Purchase Order Tracking已分配量Quantity Allocation仓位数量Quantity At Location欠交数量Quantity Backorder完成数量Quantity Completion需求量Quantity Demand毛需求量Quantity Gross进货数量Quantity In排队时间Queue Time队列Queue重生成式MRP Regenerated MRP重排假设Rescheduling Assumption资源需求计划Resource Requirements Planning粗能力计划Rough-cut Capacity Planning工艺路线Routing安全库存量Safety Stock保险期Safety Time预计入库量Scheduled Receipt残料率Scrap Factor发送零件Send Part维修件Service Parts发货地址Ship Address发货单联系人Ship Contact发货零件Ship Date发货单Ship Order 工厂日历Shop Calendar车间作业管理Shop Floor Control损耗系数Shrinkage Factor标准产品成本Standard Product Cost标准机器设置工时Standard Set Up Hour标准单位运转工时Standard Unit Run Hour标准工资率Standard Wage Rate状况代码Status Code库存控制Stores Control建议工作单Suggested Work Order约束理论Theory of Constraints (TOC)时间段Time Bucket时界Time Fence单位成本Unit Cost采购计划员Vendor Scheduler采购计划法Vendor Scheduling工作中心能力Work Center Capacity工作中心Work Center在制品Work in Process工作令跟踪Work Order Tracking工作令Work Order工作进度安排Work Scheduling零库存Zero Inventories经济订货批量＝Squat(2*年订货量*平均一次订货准备所发生成本/每件存货的年储存成本)美国生产和库存控制协会APICS，American Production & Inventory Control Society三十四、产品三十五、连接器connector三十六、端子terminal三十七、条型连接器bar connector三十八、阴连接器Housing三十九、阳连接器wafer四十、线束wire harness四十一、间距space四十二、额定电压rated voltage四十三、额定电流rated current四十四、接触电阻contact resistance四十五、绝缘电阻insulation resistance四十六、超声波焊接ultrasonic welding四十七、耐压withstand voltage四十八、针pin四十九、物料编号part number五十、导线wire五十一、基体金属Base metal五十二、电缆夹cable clamp五十三、倒角chamfer五十四、接触面积contact area五十五、接触件安装孔contact cavity五十六、接触长度contact length五十七、接触件电镀层contact plating五十八、接触压力contact pressure五十九、接触件中心距contact space六十、接触簧片contact spring六十一、插孔socket contact六十二、法兰、凸缘Flange六十三、界面间隙interfacial gap六十四、键Key六十五、键槽keyway六十六、过渡段ramp六十七、屏蔽套shielding六十八、定位基准Datum reference六十九、扁平电缆flat cable ，Ribbon cable七十、柔性印刷电线Flexible printed wiring七十一、多层印制电路Multilayer printed circuit七十二、焊盘pad七十三、图形pattern七十四、间距pitch七十五、负极Negative pole七十六、正极positive pole七十七、回流Reflow七十八、原理图Schematic diagram七十九、单面板single sided board八十、双面板Two-sided board，Double-sided board 八十一、表面安装surface Mounting八十二、翘曲warp，bow八十三、波峰焊wave soldering八十四、编织层braid八十五、同轴电缆coaxial cable八十六、电介质dielectric八十七、电缆中导线的头数ends八十八、外部干扰external interference八十九、填充物filler九十、护套jacket九十一、比重specific gravity九十二、电阻的温度系数Temperature coefficient of resistance九十三、品管九十四、SPC statistic process control九十五、品管保证Quality Assurance九十六、品管控制Quality control九十七、来料检验IQC Incoming quality control九十八、巡检IPQC In-process quality control九十九、校对calibration百、动态试验dynamic test百一、环境试验Environmental test百二、非破坏性试验non-destructive test百三、光泽gloss百四、击穿电压(dielectric) breakdown voltage百五、拉伸强度tensile strength百六、冷热骤变试验thermal shock test百七、环境试验炉Environmental chamber百八、盐雾实验salt spray test百九、绝缘电阻测试验仪Insulating resistance meter百十、内应力internal stress百十一、疲劳fatigue百十二、蠕变creep百十三、试样specimen百十四、撕裂强度tear strength 百十五、缩痕shrink mark, sink mark百十六、耐久性durability百十七、抽样sampling百十八、样品数量sample size百十九、AQL Acceptable Quality level百二十、批量lot size百二十一、抽样计划sampling plan百二十二、OC曲线operation curve百二十三、试验顺序sequence of tests百二十四、环境温度ambient temperature百二十五、可焊性solderability百二十六、阻燃性flame resistance百二十七、生产百二十八、注塑机injection machine百二十九、冲床Punch machine百三十、混料机blender mixer百三十一、尼龙nylon百三十二、黄铜brass百三十三、青铜bronze百三十四、紫(纯)铜copper百三十五、料斗hopper百三十六、麻点pit百三十七、配料compounding百三十八、涂层coating百三十九、飞边flash百四十、预热preheating百四十一、料reworked material百四十二、塑料reworked plastics百四十三、工艺设计process design百四十四、紧急停止emergency stop百四十五、延时time delay七．QS-9000中的术语APQP Advanced Product Quality Planning and Control Plan，产品先期策划和控制计划PPAP Production Part Approval Process,生产件批准程序FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析Injection machine 啤机Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力non-return valve 止回阀shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要设备Reserve pressure/packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度booster time 增压时间Compression ratio 压缩比mold close time 合模时间Resin 胶料Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降解，软化regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重Elongation 延伸率density 密度melting point 熔点Polystyrene 聚苯乙烯（PS）Styrene 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethylene 聚乙烯glass fiber 玻纤Condensation 凝固，浓缩crystalline resin 结晶形塑料Mold materials 模具General-purpose steel 多用途钢tool steel 模具钢Free-cutting steel 高速切削钢case hardening steel 表面硬化钢Pre-hardened steel 预硬钢ball and roller bearing steel 滚珠轴承钢Nonferrous steel 非铁合金high speed steel 高速钢cast iron 铸铁Steel specification 钢材规格steel certification 钢材合格证明书Stainless steel 不锈钢nickel 镍chrome 铬aluminum 铝Copper 铜brass 黄铜bronze 青铜titanium 钛Processing 钢材的加工方法Harding / quench 淬火nitride 氮化temper 回火anneal 退火Roll 轧制abrasive 研磨，磨损的finish 精加工，抛光（polish）Case-hardening 表面硬化milling machine 铣（锣）床Lathe车床drill 钻床wire cut 线割NC(numerical control ) 数控材料EDM (Electrical discharge machine) 电火花加工Cut steel 开料Precision ground 精密研磨heat treatment 热处理tap 丝锥，攻牙Texture 蚀纹weld 焊接forge 锻压deformation 变形Spraying 喷涂die-cast 压铸Properties 性能Resistance 电阻，抵抗能力abrasion / wear磨损erode / corrode 腐蚀Toughness 韧性yield strength 屈服强度tensile strength 拉伸强度Fatigue strength 疲劳强度break 断裂stress 应力hardness 硬度Humidity / moisture 潮湿，湿气roughness 粗糙度parameter 参数Thermal conductivity 导热系数manufacture 制造，加工drawback 缺点Ductility 延展性grain 晶粒property 性能，财产brittleness 脆性GD&T （Geometric Dimensions and Tolerance ）形位尺寸公差Flexural strength 挠曲强度impact 冲击conductivity 传导性，导电性Optical 光学的transparent 透明的insulation 绝缘Mechanical 机械的processability 可加工性能timeyield 蠕变Physical 物理的flow rate 流动速率compressive strength 压缩强度Adhesive 粘附的，胶合durability 耐用性Mold design 模具设计Tooling specification 模具规格mould flow 流动模拟sprue nozzle 唧咀孔Clearance 避空，间隙undercut 倒扣flush 插入，埋入legend 图例Groove 凹槽latch 插销class 类型，种类plan 平面图Orifice 孔，口column 柱位boss 凸台standard 标准，规格Rib 骨位tapered interlock 锥形管位块Bubbler 炮隆Bolt 螺钉，销顶identification mark 铭牌P/L strip 锁模片Overflow well / cold-slug well 冷料井Vent 排气pocket 槽Gate location 入水点full line 实线broken line 虚线Retainer 固定，支撑operator 操作者（啤工）receptacle 插座Lifting hole 吊令孔insulation plate 隔热板cavity number 型腔号Bolster 支撑，垫子vent channel 排气槽leak / filter 渗漏Leak test 试运水stamp / engrave 雕刻，印记（打字唛）Clamp slot 码模槽support button / pin 垃圾钉cut steel 开料Lodge 安装，放置inlay 镶嵌，插入cam / lifter 斜顶Stripper推方lifting bar 吊模方sprue 唧咀tolerance 公差Counter bore 沉孔slant 倾斜，斜面conical 圆锥的，圆锥形的Bolt 螺栓manifold 热流道板prototype tooling 原型试验Gusset 角撑reverse mold 倒装模constrain / restrict约束，限制Counter lock 反锁thermocouple 热电偶moldmaker 模具制造商Asset / property number 资产编号tool product destination 模具生产地点Accelerating ejection 加速顶出hydraulic 液压的pneumatic 气动的Trapezoid 梯形的semi-round 半圆形format 格式baffle 隔水片Electrode 电极，铜公spare part 配件gall 磨伤，插伤Cable 电缆，电线plating / coating （电）镀bonding / joint 接头Wall transition 壁厚过渡Product problem 产品问题Troubleshoot 故障处理reduce(add) plastic 减（加）胶Burr/flash披峰Burn mark 烧焦ejector mark 顶针印，顶白black specs 黑点，黑斑Discoloration 混色，污点gloss 光泽jetting/worming 走水纹Sink mark 缩水void / bubble 气泡，夹气distortion 变形Warpage 翘曲short molding / non-fill缺胶，未走齐Weld line / knit line 夹水线discarded as useless 报废Split line 夹线stick in sprue bushing / cavity / core 粘唧咀/前模/后模Break / crack 顶裂brittleness 脆性，易脆Others 其他Invoice 发票，清单vendor(er) 卖方vendee 买方guideline 方针，指导Intricate 复杂的confidential 机密的，不可外泄的proprietary 私有的Authorize 批准，授权recipient 接收者issue ①发布，提供；②问题Approve 确认，赞成requirement 需要，必需物const 常数，常量Regarding 关于，涉及opposite 相反的，对面的latitude 纬度，纵向的Version 版本definition 注释，解说transversal 横向的，截线Profile 轮廓，剖面eliminate / cancel 取消allow / permit 允许，许可Respective 各自的，分别的individual 单独的decrease 减少increase 增加Preliminary 初步的approximately 大约，近似estimate / valuate估计，预算Adjust 调整，校准application 应用，申请maintain 维持Accurate / precise 精确的smooth 光滑，顺畅的device 装置，设备Convenient 方便的deadline 截至日期available 有用的，有空的Shift 轮班，换班critical 关键的，临界的exceptional 异常的，优异的Exceed 超过layout 布局，方案loss 损失，消耗install 安装，安置Rotation 旋转item 条款，项目quotation 报价stabilize 稳定Quality 质量quantity 数量couple 连接，接合configuration 构造，外形Illustrate 图解说明simulation 模拟，仿真recommend 推荐使用。