思科产品模块说明
思科路由器接口及模块
思科路由器接口及模块思科路由器接口及模块1.介绍1.1 路由器接口的定义路由器接口是指连接路由器与其他设备之间的物理或逻辑连接口，用于传递数据。
1.2 路由器模块的定义路由器模块是指可插拔的组件，用于扩展路由器的功能和性能。
2.路由器接口类型2.1 以太网接口以太网接口是路由器与以太网网络之间的物理接口，通常使用RJ-45接头连接。
2.2 串口接口串口接口用于连接路由器与其他串行设备，如调制解调器或其他路由器。
2.3 USB接口USB接口用于连接外部设备，如存储设备或打印机。
2.4 WAN接口WAN接口用于连接路由器与广域网，通常使用专线或计算机网络线路。
3.路由器模块类型3.1 交换模块交换模块用于提供更多的以太网端口，扩展路由器的局域网连接能力。
3.2 防火墙模块防火墙模块用于增强路由器的安全性，过滤网络流量并阻止未经授权的访问。
3.3 VPN模块VPN模块用于支持虚拟专用网络，实现安全的远程访问和站点之间的互联。
3.4 模块插槽模块插槽用于插入各种不同类型的模块，根据需求进行定制和扩展。
4.法律名词与注释4.1 路由器路由器是一种用于在计算机网络中转发数据包的设备，根据网络地质进行转发决策。
4.2 以太网以太网是一种常用的局域网技术，采用CSMA/CD协议进行数据帧的传输和冲突检测。
4.3 串口串口是一种用于串行数据传输的接口，按照特定协议逐位传输数据。
4.4 USBUSB是一种通用串行总线接口，用于连接计算机与外部设备通信。
4.5 WANWAN是广域网的缩写，用于连接远距离的计算机网络。
附件：本文档未涉及附件。
本文所涉及的法律名词及注释：- 路由器：一种用于在计算机网络中转发数据包的设备，根据网络地质进行转发决策。
- 以太网：一种常用的局域网技术，采用CSMA/CD协议进行数据帧的传输和冲突检测。
- 串口：一种用于串行数据传输的接口，按照特定协议逐位传输数据。
- USB：一种通用串行总线接口，用于连接计算机与外部设备通信。
思科OptoStar II 1550 nm DWDM正向直接调制光发射模块数据手册说明书
数据手册OptoStar II 1550 nm DWDM正向直接调制光发射模块综述OptoStar II 光平台是一个先进的传输系统，专为优化网络结构而设计，从而提高网络的可靠性、可扩容性和性价比。
1550 nm直接调制光发射模块放置于OptoStar II 机框内。
在同一机框内能同时放置其它的OptoStar II 应用模块，提高了平台的使用灵活性。
在一个标准的3 RU OptoStar II 机框中可放置14个光发射模块，既可用于 FTTX 网络架构，也可为 IP QAM 输出的本地业务射频信号提供插播用光信号。
图1. OptoStar II 1550 nm 直接调制光发射模块特点● 1 GHz 带宽，为新业务提供更大的带宽容量●先进的失真矫正电路，支持模拟频道信号传输●支持DWDM应用，ITU 20 ~ 59 波长可选●独立的广播和窄播输入端口●前面板有 -20 dB测试口，方便本地调试●前面板上有LED 用来指示模块的各种工作状态●具有自动增益控制（AGC）和手动增益控制（MGC）功能●智能通信接口模块 (ICIM)，提供多种设置和控制方式- 通过 ICIM 的 LCD 屏幕直接进行本地监控- 通过 ICIM 的小型 USB 接口，连接 PC 端的配套软件 (Console) 进行本地监控- 通过 ICIM 的 RJ-45 接口，进行远程状态监测 (SNMP)●可以对固件 (Firmware) 进行升级●支持热插拔功能产品规格表1.光性能指标表2.电性能指标表3.环境和机械性能指标表4.链路载噪比性能指标1,2表5.链路失真性能指标1,2表6.256 QAM BER性能指标1,2,6注：1. 输入信号为未调制的连续波 (CW) 和 256 QAM2. 光纤链路损耗由20 km 或10 km 光纤和光衰减器组成，光接收功率为 0 dBm3. 输入30 个NTSC载波，其射频电平为 15 dBmV/CH，和124个256 QAM 载波，其电平比模拟信号低 6dB，MGC模式，0 dB衰减4. 输入30 个PAL D/K载波，其射频电平为 16 dBmV/CH，和85个256 QAM 载波，其电平比模拟信号低6 dB，MGC模式，0 dB衰减5. 输入153 个256 QAM 载波，其射频电平为 13 dBmV/CH，MGC模式，0 dB衰减6. BER 值是按ITU-T J.83 附录B 规定条件，15 分钟测试时间的平均值除非另行通知，上述指标是参照OptoStar II 机框进风口处的环境温度时的标称性能。
思科MGE SFP模块数据表说明书
Data Sheet Cisco MGE SFP Modules Cisco Small Business Network AccessoriesEasily connect switches with fiber-optic networking modulesHighlights●Adds fiber-optic connectivity to Cisco 100 to 500 Series switches●High-performance link for connecting networks within a building or small business area●Easy removal with an integrated spring latch●Hot swappable to maintain network availability●Flexibility of media and interface choice on a port-by-port b asis, so you can “pay as you populate”Product overviewCisco® MGE Small Form-Factor Pluggable (SFP) or mini Gigabit Interface Converter (mini-GBIC) transceivers are easy-to-install modules that provide a simple way to add fiber connectivity or an extra Gigabit Ethernet port to your Cisco 100, 200, 300, and 500 Series switches. The transceivers are available for single-mode or multimode fiber-optic cabling and can support distances from 100 meters up to 40 kilometers.The Cisco MGE transceivers provide fast, reliable connectivity between switches located on different floors, in separate buildings, or on a small campus network needing connectivity between sites. These transceivers can support Gigabit Ethernet applications. Figures 1 and 2 show the fiber-optic and copper transceivers. Table 1 lists the transceiver modules.Figure 1. Cisco optical Gigabit Ethernet SFP moduleFigure 2. Cisco 1000BASE-T copper SFPTable 1. MGE SFP transceiver modulesFeatures●Built-in spring latch for easy module removal●Hot swappable●Low-insertion-loss duplex LC receptacle●Low electromagnetic interference (FCC Part 15, Class B) for clear communications●Meets FDA and International Electrotechnical Commission (IEC) eye safety standardsCisco limited warrantyThe Cisco Small Business transceivers come with a 5-year limited hardware warranty with return-to-factory replacement. In addition, Cisco offers software updates for bug fixes at no charge for the life of the warranty and 1 year of telephone technical assistance from the Small Business Support Center. For more information, visit https:///en/US/docs/general/warranty/5year_SmallBusiness.html.The Cisco MGE SFP transceivers are supported across a variety of Cisco Small Business switches.●110 Series Unmanaged Switches●220 Series Smart Switches●250 Series Smart Switches●350 Series Managed Switches●350X Series Stackable Managed Switches●550X Series Stackable Managed SwitchesSpecificationsTable 2 contains the specifications, package contents, and minimum requirements for the Cisco MGE SFP transceivers.Table 2. SpecificationsOrdering informationTable 3 provides ordering information for the Cisco MGE transceivers.Table 3. Ordering informationCisco CapitalFlexible payment solutions to help you achieve your objectivesCisco Capital makes it easier to get the right technology to achieve your objectives, enable business transformation and help you stay competitive. We can help you reduce the total cost of ownership, conserve capital, and accelerate growth. In more than 100 countries, our flexible payment solutions can help you acquire hardware, software, services and complementary third-party equipment in easy, predictable payments. Learn more.For more informationFor more information about Cisco 100 to 500 Series products and solutions, visit the Cisco Small Business Technology webpage or the product page.。
cisco 思科 Catalyst 9400 管理引擎模块 产品手册
思科公开信息思科 Catalyst 9400 管理引擎模块目录产品概述 (3)详细信息 (4)特性 (5)平台优势 (12)许可 (16)规格 (19)保修 (23)订购 (24)Cisco Capital (25)文档历史记录 (26)产品概述思科 Catalyst® 9400 系列是思科专为安全性、物联网 (IoT) 和多云环境打造的主打模块化企业交换接入和汇聚平台。
该系列交换机是思科领先的企业架构思科® SD-Access 的基本组件。
该平台采用最高支持 9 Tbps 系统带宽的机箱架构，并具备符合高密度 IEEE 802.3bt 标准的业界领先功率输出（60W 和 90W PoE），可为您提供强大的投资保护。
现在，整个产品组合都具有提供冗余的能力。
依靠无中断转发和状态切换 (NSF/SSO)、服务中软件升级 (ISSU)、上行链路恢复能力、电源 N+1/N+N 冗余以及思科 StackWise®虚拟 (SVL)（带 ISSU）等功能，思科 Catalyst 9400 系列交换机可实现一流的高可用性。
该平台面向企业进行了优化，采用了创新的双向维护风扇托架和侧向气流设计，非常适合对深度约为 16 英寸的配线柜进行部署。
单个系统可扩展至最多 384 个接入端口，并可选择 1 千兆以太网铜缆、1 千兆以太网光纤、思科 UPOE +©、思科通用型以太网供电（思科 UPOE®）和增强型以太网供电 (PoE+) 等多种端口类型；也可扩展至最多 192 个端口，并可选择 10G 光纤和多千兆等多种端口类型。
该平台还支持高级路由和基础设施服务、SD-Access 功能，以及网络系统虚拟化。
借助这些功能，您可以将该平台部署到中小型园区环境的核心层和汇聚层中。
软件定义架构的基础要应对高级持续性安全威胁、物联网 (IoT) 设备的指数级增长、无处不在的移动性和云的采用等等趋势，必须采用一种集高级硬件和软件创新于一身的网络交换矩阵，在保护和简化客户网络的同时，使客户网络实现自动化。
思科 Nexus 9500 云级线卡和交换矩阵模块 产品手册说明书
产品手册思科 Nexus 9500云级线卡和交换矩阵模块目录产品概述3思科 Nexus 9500 平台云级线卡3思科 Nexus 9500 云级平台交换矩阵模块和性能5支持的光纤模块6机械规格7监管标准合规性8订购信息8保修9服务与支持9 Cisco Capital 10更多信息10产品概述思科 Nexus® 9500 交换平台（图 1）提供三种模块化机箱：●思科 Nexus 9500 4 插槽交换机●思科 Nexus 9500 8 插槽交换机●思科 Nexus 9500 16 插槽交换机图 1.思科 Nexus 9500 系列云级交换机机箱思科 Nexus 9500 系列模块化交换机能够支持最高 172.8 Tbps 的带宽，并可通过全面的云级线卡和交换矩阵模块选择提供 1、10、25、40、50 和 100 千兆以太网接口。
使用这些云级线卡，最多可为思科 Nexus 9500 系列交换机配置1. 576 个 100 千兆以太网端口（或）2. 576 个 40 千兆以太网端口（或）3. 2304 个 25 千兆以太网端口（或）4. 2304 个 1/10 千兆以太网端口思科 Nexus 9500 平台云级线卡思科 Nexus 9500 平台广泛支持针对数据中心部署优化的各种热插拔多速云级线卡和交换矩阵模块。
这些云级线卡和交换矩阵模块使用思科®云级 ASIC 构建，为大型可扩展数据中心提供了理想的基础。
思科云级 ASIC 可提供满足全球最大云级数据中心不断发展的需求所需的增强性能和功能。
这些 ASIC 不仅可支持基础性的第 2/3 层网络功能，还能支持一些增强功能，例如基于策略的交换矩阵架构（ACI 或 VXLAN）、智能缓冲、集成线速安全和通过多速以太网端口进行的实时数据流遥测。
表 1.思科 Nexus 9500 云级线卡N9K-X9732C-EX：100 千兆以太网线卡N9K-X9736C-FX：100 千兆以太网线卡N9K-X9732C-FX：100 千兆以太网线卡N9K-X9736C-EX：100 千兆以太网线卡N9K-X97160YC-EX：1/10/25 千兆以太网接入层以及10/40/100 千兆以太网汇聚层线卡N9K-X9788TC-FX：1/10 千兆以太网 BaseT 接入层以及 40/100 千兆以太网汇聚层线卡表 2.思科 Nexus 9500 云级线卡规格*要使用 5 个交换矩阵模块和 X9736C-FX 线卡实现最大带宽，机箱中的线卡只能为 X9736C-FX 线卡。
思科 分支机构路由器系列网络分析模块 说明书
合理调整网络，减少网络支出 确定服务趋势，以预测基础设施改进，更好地满足对于服务的更
高需求。
节约总拥有成本（TCO）
思科NAM解决方案的集成特性节约了运营、维护和技术支持成
本。思科NAM流量分析器免费提供。思科分支机构路由器系列
NAM的维护包括在分支机构路由器维护合同中。
产品规格
表2提供了思科分支机构路由器系列NAM的规格。
改进用户体验应用性能的方式 思科分支机构路由器系列NAM提供了有关分支机构中客户端所体验到的应用性能的重要信息。利用 思科应用响应时间 (ART) MIB扩展，思科NAM能跟踪响应时间，将应用性能问题隔离在网络或应用 服务器中。利用这些反应用户网络性能体验的测量数据，能够快速识别性能下降的根源，并在用户 注意到有问题出现之前就解决问题。 思科NAM收集基于TCP的客户端/服务器请求的响应时间统计数据，报告与任意端口或接口相连的关 键设备的响应时间统计数据。响应时间分析和报告是完全可定制的；用户能定义以多长的时间间隔 来测量应用和服务器，全面控制响应时间报告。此外，也能确定响应时间数据的趋势。由此，能够 将网络和应用使用情况的变化与响应时间的波动相关联，预测用户数或广域网带宽管理的变化会对 应用性能产生什么影响（图6）。
远程机构
易于部署和使用 思科NAM包括一个基于Web的轻量流量分析器GUI (图3) ，能从任意桌面进行访问，无需派遣人员 前往远程地点或通过广域网链路向中央站点发送大量数据。
2
图3. 通过内嵌的思科NAM流量分析器进行基于Web的流量监控
思科NAM流量分析器使用RMON II等MIB和NBAR-PD来分析和存储收集到的数据，提供网络和应用 性能的全面视图，包括有关数据、语音和视频流量，DiffServ配置，主机，通话双方，应用使用和应 用响应时间(ART)的重要信息（图4）。
思科 10GBASE SFP+ 模块 数据表说明书
Cisco 10GBASE SFP+ModulesData sheet Cisco publicContentsProduct overview 3 Features and benefits 3 Cisco SFP-10G-T-X module 4 Cisco SFP-10G-SR-S module (S-Class) 4 Cisco SFP-10G-SR module 4 Cisco SFP-10G-SR-X module 5 Cisco SFP-10G-SR-I module 5 Cisco SFP-10G-LRM module 5 Cisco FET-10G module 5 Cisco SFP-10G-LR-S module (S-Class) 5 Cisco SFP-10G-LR module 5 Cisco SFP-10G-LR-X module 6 Cisco SFP-10G-LR10-I module 6 Cisco SFP-10G-ER-S module (S-Class) 7 Cisco SFP-10G-ER module 7 Cisco SFP-10G-ER-I module 7 Cisco SFP-10G-ZR-S module (S-Class) 7 Cisco SFP-10G-ZR module 7 Cisco SFP-10G-ZR-I module 8 Cisco SFP+ Twinax copper cables 8 Cisco SFP+ Active optical cables 9 Platform support 9 Product specifications 10 Warranty 19 Cisco environmental sustainability 19 Ordering information 20 Regulatory and standards compliance 21 Cisco Capital 22 Next steps 22 Document history 23A broad range of industry-compliant SFP+ modules for 10 Gigabit Ethernet deploymentsin diverse networking environments.Product overviewThe Cisco® 10GBASE SFP+ modules (Figure 1) give you a wide variety of 10 Gigabit Ethernet connectivity options for data center, enterprise wiring closet, and service provider transport applications.Figure 1.Cisco 10GBASE SFP+ modulesFeatures and benefitsCisco SFP+ modules offer the following features and benefits.●Industry’s smallest 10G form factor for greatest density per chassis●Hot-swappable input/output device that plugs into an Ethernet SFP+ port of a Cisco switch (no need topower down if installing or replacing)●Supports “pay-as-you-populate” model for investment protection and ease of technology migration●Digital optical monitoring capability for strong diagnostic capabilities●Optical interoperability with 10GBASE XENPAK, 10GBASE X2, and 10GBASE XFP interfaces on the samelink●Cisco quality Identification (ID) feature enables a Cisco platform to identify whether the module iscertified and tested by CiscoCisco SFP-10G-T-X moduleThe Cisco 10GBASE-T module (Figure 2) offers connectivity options at the following data rates:100M/1G/10Gbps. It has the SFP+ form factor and an RJ-45 interface so that CAT5e/CAT6A/CAT7 cables can be used to connect to end points with embedded 10GBASE-T ports. They are suitable for distances up to 30 meters and offers a cost-effective way to connect within racks and across adjacent racks.Figure 2.Cisco SFP+ 10GBASE-T module with RJ-45 connectorTable 1, details the specifications for the SFP-10G-T-X module, including cable type, distance, and data rates supported.Table 1.SFP-10G-T-X cabling specificationsCisco SFP-10G-SR-S module (S-Class)The Cisco 10GBASE-SR module supports a link length of 26 meters on standard Fiber Distributed Data Interface (FDDI)-grade Multimode Fiber (MMF). Using 2000 MHz*km MMF (OM3), up to 300-meter link lengths are possible. Using 4700 MHz*km MMF (OM4), up to 400 meter link lengths are possible. SFP-10G-SR-S does not support FCoE.Cisco SFP-10G-SR moduleThe Cisco 10GBASE-SR Module supports a link length of 26m on standard Fiber Distributed Data Interface (FDDI)-grade Multimode Fiber (MMF). Using 2000MHz*km MMF (OM3), up to 300m link lengths are possible. Using 4700MHz*km MMF (OM4), up to 400m link lengths are possible.Cisco SFP-10G-SR-X moduleThe Cisco SFP-10G-SR-X is a multirate* 10GBASE-SR, 10GBASE-SW and OTU2/OTU2e module for extended operating temperature range. It supports a link length of 26m on standard Fiber Distributed Data Interface (FDDI)-grade Multimode Fiber (MMF). Using 2000MHz*km MMF (OM3), up to 300m link lengths are possible. Using 4700MHz*km MMF (OM4), up to 400m link lengths are possible.* Except for version 1, which supports only 10GBASE-SR.Cisco SFP-10G-SR-I moduleThe Cisco SFP-10G-SR-I is a multirate 10GBASE-SR, 10GBASE-SW and OTU2/2e module for industrial operating temperature range. This module also supports CPRI datarate options 3, 4, 5, 6, 7, 7a, 8. It supports a link length of 26m on standard Fiber Distributed Data Interface (FDDI)-grade Multimode Fiber (MMF). Using 2000MHz*km MMF(OM3), up to 300m link lengths are possible. Using 4700MHz*km MMF (OM4), up to 400m link lengths are possible.Cisco SFP-10G-LRM moduleThe Cisco 10GBASE-LRM Module supports link lengths of 220m on standard Fiber Distributed Data Interface (FDDI) grade Multimode Fiber (MMF). To make sure that specifications are met over FDDI-grade, OM1 and OM2 fibers, the transmitter should be coupled through a mode conditioning patch cord. No mode conditioning patch cord is required for applications over OM3 or OM4. For additional information on mode conditioning patch cord requirements please see:https:///en/US/prod/collateral/modules/ps5455/product_bulletin_c25-530836.html.The Cisco 10GBASE-LRM Module also supports link lengths of 300m on standard Single-Mode Fiber (SMF, G.652).Cisco FET-10G moduleThe Cisco FET-10G Fabric Extender Transceiver supports link lengths up to 100m on laser-optimized OM3 or OM4 multimode fiber. It is supported on fabric links from a Nexus 2000 to a Cisco parent switch only. Note this product is not orderable individually. For more information refer to Nexus 2000 datasheet:https:///en/US/prod/collateral/switches/ps9441/ps10110/data_sheet_c78-507093.html.Cisco SFP-10G-LR-S module (S-Class)The Cisco 10GBASE-LR module supports a link length of 10 kilometers on standard Single-Mode Fiber (SMF) (G.652). SFP-10G-LR-S does not support FCoE.Cisco SFP-10G-LR moduleThe Cisco 10GBASE-LR Module supports a link length of 10 kilometers on standard Single-Mode Fiber (SMF, G.652).Cisco SFP-10G-LR-X moduleThe Cisco SFP-10G-LR-X is a multirate 10GBASE-LR, 10GBASE-LW, and OTU2/OTU2e module for extended operating temperature range. It supports a link length of 10 kilometers on standard Single-Mode Fiber (SMF, G.652).Cisco SFP-10G-LR10-I moduleThe Cisco SFP-10G-LR10-I supports a link length of 10 kilometers on standard Single-Mode Fiber (SMF, G.652). The SFP-10G-LR10-I is for industrial operating temperature range. The SFP-10G-LR10-I also supports CPRI datrates options 3, 4, 5, 6, 7, 7a, 8.Cisco SFP-10G-BXD-I and SFP-10G-BXU-I for 10Km (single-fiber bidirectional applications)The Cisco SFP-10G-BXD-I and SFP-10G-BXU-I SFPs operate on a single strand of standard SMF.A SFP-10G-BXD-I device is always connected to a SFP-10G-BXU-I device with a single strand of standard SMF with an operating transmission range up to 10 km.The communication over a single strand of fiber is achieved by separating the transmission wavelength of the two devices, as depicted in Figure 3. SFP-10G-BXD-I transmits a 1330-nm channel and receives a 1270-nm signal, whereas SFP-10G-BXU-I transmits at a 1270-nm wavelength and receives a 1330-nm signal. Note in Figure 3 the presence of a Wavelength-Division Multiplexing (WDM) splitter integrated into the SFP to split the 1270-nm and 1330-nm light paths. This module also supports CPRI datarate options 3, 4, 5, 6, 7, 7a, 8.*Figure 3.Bidirectional transmission of a single strand of SMFThe SFP-10G-BXD-I and SFP-10G-BXU-I SFPs also support Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.*Version -02 of SFP-10G-BXD-I and SFP-10G-BXU-I supports the CPRI rates.Cisco SFP-10G-ER-S module (S-Class)The Cisco 10GBASE-ER module supports a link length of up to 40 kilometers on SMF (G.652). SFP-10G-ER-S does not support FCoE.Cisco SFP-10G-ER moduleThe Cisco 10GBASE-ER Module supports a link length of up to 40 kilometers on standard Single-Mode Fiber (SMF, G.652).Cisco SFP-10G-ER-I moduleThe Cisco 10GBASE-ER Industrial Temperature Module supports a link length of up to 40 kilometers on standard Single-Mode Fiber (SMF, G.652). The SFP-10G-ER-I for Industrial Operating Temperature Range is a multirate 10GBASE-ER, 10GBASE-EW and OTU2/2e module.Cisco SFP-10G-BX40D-I and SFP-10G-BX40U-I (for 40Km single-fiber bidirectional applications)The Cisco SFP-10G-BX40D-I and SFP-10G-BX40U-I SFPs operate on a single strand of standard SMF.A SFP-10G-BX40D-I device is always connected to a SFP-10G-BX40U-I device with a single strand of standard SMF with an operating transmission range up to 40 km.The communication over a single strand of fiber is achieved by separating the transmission wavelength of the two devices. SFP-10G-BX40D-I transmits a 1330-nm channel and receives a 1270-nm signal. The SFP-10G-BX40U-I transmits at a 1270-nm wavelength and receives a 1330-nm signal.The SFP-10G-BX40D-I and SFP-10G-BX40U-I SFPs support Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.Cisco SFP-10G-ZR-S module (S-Class)The Cisco 10GBASE-ZR module supports link lengths of up to about 80 kilometers on standard SMF (G.652). This interface is not specified as part of the 10 Gigabit Ethernet standards and is, instead, built according to Cisco specifications. SFP-10G-ZR-S does not support FCoE.Cisco SFP-10G-ZR moduleThe Cisco SFP-10G-ZR is a multirate 10GBASE-ZR, 10GBASE-ZW, and OTU2/OTU2e module. It supports link lengths of up to about 80 kilometers on standard Single-Mode Fiber (SMF, G.652). This interface is not specified as part of the 10 Gigabit Ethernet standard and is instead built according to Cisco specifications.Cisco SFP-10G-ZR-I moduleThe Cisco SFP-10G-ZR-I is a multirate 10GBASE-ZR, 10GBASE-ZW, and OTU2/OTU2e module for industrial operating temperature range. The SFP-10G-ZR-I has a limiting electrical interface receiver, which does not require EDC PHY on the host board, it can be plugged into any SFP+ port. It supports link lengths of up to 70 kilometers on standard Single-Mode Fiber (SMF, G.652), assuming a fiber chromatic dispersion of20 ps/(nm*km). This interface is not specified as part of the 10 Gigabit Ethernet standard and is instead built according to Cisco specifications. The SFP-10G-ZR-I has a cold start at -40⁰C; the transceiver will be operational except optical traffic is not supported from -40⁰ to -28⁰C, all other low speed features (DOM, I2C, etc.) are operational. The module is fully operational from -28⁰C to 85⁰C.Cisco SFP+ Twinax copper cablesCisco SFP+ Copper Twinax (Figure 4) direct-attach cables are suitable for very short distances and offer a cost-effective way to connect within racks and across adjacent racks. Cisco offers passive Twinax cables in lengths of 1, 1.5, 2, 2.5, 3, 4 and 5 meters, and active Twinax cables in lengths of 7 and 10 meters.Figure 4.Cisco direct-attach twinax copper cable assembly with SFP+ connectorsCisco SFP+ Active optical cablesCisco SFP+ Active Optical Cables (Figure 5) are direct-attach fiber assemblies with SFP+ connectors. They are suitable for very short distances and offer a cost-effective way to connect within racks and across adjacent racks. Cisco offers Active Optical Cables in lengths of 1, 2, 3, 5, 7, and 10 meters.Figure 5.Cisco direct-attach active optical cables with SFP+ connectorsPlatform supportCisco SFP+ modules are supported on a wide range of Cisco switches and routers*:Table 2.Cisco Platforms* Not all devices listed support every module. For details about which modules run in which devices and other compatibility information, refer to the document “Cisco 10 Gigabit Ethernet Transceiver Modules Compatibility Matrix”:https:///en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6974.html.Additional platforms may continually be added; please check the compatibility matrix for the latest information and for the Cisco compatible operating system for each platform.Connectors: Dual LC/PC connector (-SR, -LRM, -LR, -ER, -ZR and FET-10G).Note: Only connections with patch cords with PC or UPC connectors are supported. Patch cords withAPC connectors are not supported. All cables and cable assemblies used must be compliant with the standards specified in the standards section.Product specificationsTable 3 provides cabling specifications for the Cisco SFP+ modules.Table 3.SFP+ port cabling specifications*1 Minimum cabling distance for -SR, -LRM, -LR, -ER modules is 2m, according to the IEEE 802.3ae.*2 Links longer than 30km are considered engineered links as per IEEE 802.3ae.*3 Specified at transmission wavelength.*4 Requires 5 dB 1550nm fixed loss attenuator for < 20km. Attenuator is available as a spare. The part number is 15216 ATT LC 5=. *5 Requires 15dB attenuator if Link Distance < 5km.Requires 10dB attenuator if Link Distance is between 5km and 25km.Requires 5dB attenuator if Link Distance is between 25km and 45km.*6 Requires 15dB attenuator if Link Distance < 5km.Requires 10dB attenuator if Link Distance is between 5km and 15km.Requires 5dB attenuator if Link Distance is between 15km and 25km.Attenuator is available as a spare. The part numbers:●5dB - 15216 ATT LC 5=●10dB - 15216 ATT LC 10=●15dB - 15216 ATT LC 15=a - No FCoE support.b - Links up to 15 km are supported as engineered links as long as channel insertion loss < 6.2 dB. Table 4 lists the main optical characteristics for the Cisco SFP+ modules.Table 4.Optical transmit and receive specifications* Transmitter and receiver power is in average, unless specified.** The launch power shall be the lesser of the class 1 safety limit or the maximum receive power. Class 1 laser requirements are defined by IEC 60825-1: 2001.*** Both average and OMA specifications must be met simultaneously.Table 5 details optical specifications for the Cisco SFP-10G-ZR modules.Table 5.SFP-10G-ZR, SFP-10G-ZR-S optical parameters*Maximum chromatic dispersion for SFP-10G-ZR and SFP-10G-ZR-S is 1600 ps/nm.Note: Parameters are specified over temperature and at end of life unless otherwise noted. When shorter distances of single-mode fiber are used (<40km), an inline optical attenuator must be used to avoid overloading and damaging the receiver.Table 6.SFP-10G-ZR-I optical parameters*Maximum chromatic dispersion for SFP-10G-ZR-I is 1400 ps/nm.Note: Parameters are specified over temperature and at end of life unless otherwise noted. When shorter distances of single-mode fiber are used (<40km), an inline optical attenuator must be used to avoid overloading and damaging the receiver.Table 7 describes the bail latch color code for each type of optical SFP+ module. Table 7.SFP+ optical modules color codeTable 8 provides the maximum power consumption and operating temperature range ratings per Cisco SFP+ module.Table 8.SFP+ modules power consumption* The SFP-10G-ZR-I has a cold start at -40⁰C, the transceiver will be operational except optical traffic is not supported from -40⁰C to -28⁰C, all other low speed features(DOM, I2C, etc.) are operational. The module is fully operational -28⁰C to 85⁰C. DimensionsDimensions (H x W x D): 8.5 x 13.4 x 56.5mm. Cisco SFP+ connectors typically weigh 75 grams or less. Environmental Conditions and Power RequirementsOperating temperature range:●Commercial temperature range (COM): 0 to 70°C (32 to 158°F)●Extended temperature range (EXT): -5 to 85°C (23 to 185°F)●Industrial temperature range (IND): -40 to 85°C (-40 to 185°F)●Storage temperature range: -40 to 85°C (-40 to 185°F)Warranty●Standard warranty: 5 years●Expedited replacement available via a Cisco SMARTnet® Service support contractCisco environmental sustainabilityInformation about Cisco’s environmental sustainability polic ies and initiatives for our products, solutions, operations, and extended operations or supply chain is provided in the “Environment Sustainability” section of Cisco’s Corporate Social Responsibility (CSR) Report.Reference links to information about key environmental sustainability topics (mentioned in the “Environment Sustainability” section of the CSR Report) are provided in the following table:Cisco makes the packaging data available for informational purposes only. It may not reflect the most current legal developments, and Cisco does not represent, warrant, or guarantee that it is complete, accurate, or up to date. This information is subject to change without notice.Ordering informationTable 9 provides the ordering information for Cisco SFP+ modules and related cables. Table 9.Ordering informationRegulatory and standards complianceStandards:●GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable●GR-326-CORE: Generic Requirements for Single-Mode Optical Connectors and Jumper Assemblies●GR-1435-CORE: Generic Requirements for Multifiber Optical Connectors●IEEE 802.3: 10-Gigabit Ethernet●ITU-T G.709: Interfaces for the Optical Transport Network●ITU-T G.975: GFEC●ITU-T G.975.1: EFEC●SFP+ MSA SFF-8431 (Optical Modules, Active Optical Cables, and Passive Twinax cables)●SFP+ MSA SFF-8461 (Active Twinax cables)Safety:●Laser Class 1 21CFR-1040 LN#50 7/2001●Laser Class 1 IEC60825-1●Cable jacket of SFP+ copper modules is UL #E116441 Compliant●All length SFP+ copper cables are ELV and RoHS CompliantCisco CapitalFlexible payment solutions to help you achieve your objectivesCisco Capital makes it easier to get the right technology to achieve your objectives, enable business transformation and help you stay competitive. We can help you reduce the total cost of ownership, conserve capital, and accelerate growth. In more than 100 countries, our flexible payment solutions can help you acquire hardware, software, services and complementary third-party equipment in easy, predictable payments. Learn more.Next stepsLearn more about Cisco 10GBASE SFP+ fiber modules or 10GBase SFP+ copper modules (twinax cable) by contacting your sales representative or visiting https:///en/US/products/ps6574/index.html. For S-Class SFP+ 10 Gigabit Modules, refer to the link below:https:///c/en/us/products/interfaces-modules/transceiver-modules/datasheet-listing.html.Document historyPrinted in USA C78-455693-27 08/22。
带你全面认识思科路由器接口及模块
思科路由器的接口类型繁多，要认识并能正确采购而且能正确使用它是一件有挑战意义的事情。
事情。
本文以思科公司最通用、最典型的路由器型号——本文以思科公司最通用、最典型的路由器型号——Cisco2600Cisco2600系列为例来进行说明。
思科在早期的路由器科在早期的路由器((如Cisco2500系列系列))中，接口都是固定化设计，接口都是固定化设计，从从Cisco2600系列起，开始采用模块化设计，部分接口部分接口((接口卡和网络模块接口卡和网络模块))将由客户根据自己的需要来选购，这使得思科的路由器产品具有极强的升级和扩展能力。
思科的路由器产品具有极强的升级和扩展能力。
思科公司的Cisco2600系列路由器具有企业级的通用性、集成性和扩展性。
随着企业新应用的出现，这个系列的模块化结构能适应网络技术的变化，能通过更换接口卡和网络模块进行升级。
进行升级。
Cisco2600Cisco2600系列配置了强大的RISC 处理器，能够支持高级服务质量处理器，能够支持高级服务质量(QoS)(QoS)(QoS)、安全、安全和网络集成等多种服务。
Cisco2600系列与Cisco1600Cisco1600、、1700和3600系列共享模块化接口，为Internet Internet、内部网访问、语音、内部网访问、语音、内部网访问、语音//数据集成、模拟和数字拨号访问服务、数据集成、模拟和数字拨号访问服务、VPN VPN 访问、访问、ATM ATM 访问、问、VLAN VLAN 以及路由管理等提供全面的解决方案。
这个系列的路由器是目前中小企业使用得最多的路由器型号，完全有能力适应中小企业不断发展的网络应用需求，虽然它被思科公司定义为“使用在中小企业分支机构里”，但是对于需求不是很高级的用户往往把它用在网络的核心。
的核心。
（注－）思科的Cisco2600系列包括：系列包括：261026102610、、26112611、、26132613、、26202620、、26212621、、26502650、、2651(2651(以上型号以上型号思科公司在全球已经停止出销售思科公司在全球已经停止出销售))和2610XM 2610XM、、2611XM 2611XM、、26122612、、2620XM 2620XM、、2621XM 2621XM、、2650XM 2650XM、、2651XM 2651XM、、2691(2691(正在销售正在销售正在销售)()()(见图见图1)1)。
思科 2900 和 3900 系列路由器的思科增强型 EtherSwitch 服务模块 说明书
用于思科 2900 和 3900 系列路由器的思科增强型 EtherSwitch 服务模块思科®增强型 EtherSwitch®服务模块可以将千兆以太网 (GE) 和快速以太网 (FE) 交换机端口，集成到思科 3900 和 2900 系列集成多业务路由器中，从而帮助您的企业降低总体拥有成本。
这种集成使网络管理员能够使用思科管理工具，或用用于局域网和广域网管理的路由器命令 (CLI) 来管理单一设备。
这种方式可以降低网络复杂性、降低维护成本、缓解员工培训需求、简化软件资格认证工作、提高可用性，以及为分支机构和总部提供一致的应用体验。
产品概述通过集成行业领先的第二层和第三层交换，获得思科 Catalyst® 3560- E 和 Catalyst 2960 系列交换机的同等特性，思科增强型 EtherSwitch 服务模块（图 1）可以极大地扩展路由器的功能。
全新的思科增强型 EtherSwitch 服务模块率先利用了思科 3900 和 2900 系列集成多业务路由器中的新增功能。
此外，这些服务模块还支持思科的行业领先的电能管理计划，即思科 EnergyWise®、思科增强型以太网供电（ePoE）和端口 PoE 电能监控。
所有这些使分支机构可通过扩展更加轻松地满足下一代网络需求，同时通过重要计划确保 IT 团队在高能效的网络中工作。
思科增强型 EtherSwitch 服务模块不仅执行本地线路速率交换和路由，还能通过第二代集成多业务路由器多千兆矩阵（Multigigabit Fabric，MGF）分离局域网和广域网资源，从而支持“网络模块到服务模块”的直接通信。
图 1. 思科增强型 EtherSwitch 服务模块思科增强型 EtherSwitch 服务模块类型思科增强型 EtherSwitch 服务模块提供了两种类型（表 1）：入门级 (ES2) 和高级 (ES3)。
Cisco路由器接口及模块简介
Cisco路由器接口及模块简介本文以思科公司最通用、最典型的路由器型号——Cisco2600系列为例来进行说明。
思科在早期的路由器（如Cisco2500系列）中，接口都是固定化设计，从Cisco2600系列起，开始采用模块化设计，部分接口（接口卡和网络模块）将由客户根据自己的需要来选购，这使得思科的路由器产品具有极强的升级和扩展能力。
思科公司的Cisco2600系列路由器具有企业级的通用性、集成性和扩展性。
随着企业新应用的出现，这个系列的模块化结构能适应网络技术的变化，能通过更换接口卡和网络模块进行升级。
Cisco2600系列配置了强大的RISC处理器，能够支持高级服务质量（QoS）、安全和网络集成等多种服务。
Cisco2600系列与Cisco1600、1700和3600系列共享模块化接口，为Internet、内部网访问、语音/数据集成、模拟和数字拨号访问服务、VPN访问、A TM访问、VLAN以及路由管理等提供全面的解决方案。
这个系列的路由器是目前中小企业使用得最多的路由器型号，完全有能力适应中小企业不断发展的网络应用需求，虽然它被思科公司定义为“使用在中小企业分支机构里”，但是对于需求不是很高级的用户往往把它用在网络的核心。
思科的Cisco2600系列包括：2610、2611、2613、2620、2621、2650、2651（以上型号思科公司在全球已经停止出销售）和2610XM、2611XM、2612、2620XM、2621XM、2650XM、2651XM、2691（正在销售）（见图1）。
表1为正在销售的Cisco2600XM和2612、2691的接口基本配置。
在Cisco2600系列中，有些接口是固化，而有些接口是模块化设计，被用户选购来安装在广域网接口插槽和网络模块插槽里。
固定化配置的接口有：辅助口（AUX）和控制口（CON）都各有一个；以态网口（ETHERNET）会有一个到两个；令牌环（TR）只有在Cisco2612、Cisco2613中有一个。
思科ISR 2800、3800和3900集成服务路由器的T3 E3 ATM网络模块说明书
Data SheetT3/E3 ATM Network Modules for Cisco 2800, 3800 and 3900 Integrated Services RoutersThe new Cisco T3/E3 ATM Network Module (NM-1A-T3/E3) is now available for the Cisco ISR 2800, 3800 and 3900 Series Routers that provide ATM WAN connectivity for enterprise regional and branch office connectivity. This combined T3/E3 ATM network module provides an ATM connection of either 44 Mbps for DS3/T3, or 34 Mbps for E3 using standard 75-ohm BNC connectors. Support is provided for ATM Forum compliant framing standard AAL5, as well as ATM Traffic Management support for Unspecified Bit Rate (UBR), UBR+ (For SVC’s only), Variable Bit Rate real-time (VBR-rt), Variable Bit Rate non-real time (VBR-nrt), Constant Bit Rate (CBR), and Available Bit Rate (ABR) classes of traffic.The T3/E3 ATM network modules provide a cost-effective solution that can be deployed in the Cisco 2800,3800, and 3900 ISR’s as Service Provider Managed customer premise equipment (CPE) or by Enterprise customers for T3/E3 and Fractional T3/E3 connectivity to medium-to-large size branch and smaller regional office locations for consolidating multiservice data, voice and video services over a single ATM link.Figure 1. T3/E3 ATM Network ModuleThe following key features are supported:●ATM Classes of Service support for: Unspecified Bit Rate (UBR), UBR+ (SVC’s only), Variable Bit Ratereal-time (VBR-rt), Variable Bit Rate non-real time (VBR-nrt), Constant Bit Rate (CBR), and Available Bit Rate (ABR)●RFC 1483 and RFC 1577 support●1024 maximum simultaneous Virtual Connections (VCs)●8 bits of VPI (VPI range 0-255), 16 bits of VCI (VCI range 0-65535)●Permanent Virtual Circuits (PVCs) and Switched Virtual Circuits (SVCs)●PLCP and HEC cell delineation support●Operations and Management (F4,F5 OAM) cell support●LANE support●ILMI 1.0 support●IETF PPP over ATM support●Multiprotocol Label Swapping (MPLS) VPN support●MPOA Client and Server●Next Hop Routing Protocol (NHRP)●On-line Insertion and Removal (OIR) on 3845●Permanent Virtual Path (PVPs) support●FRF.5/8 Interworking●ITU-T G.703 Compliant●ATM Traffic Management 4.1 compliant●ATM Forum UNI 3.1/4.0 PVC compliant●ATM Forum UNI 4.0 SVC compliantTable 1 shows minimum Cisco IOS release and feature sets requirement for the product.Table 1. Cisco IOS Support and Orderability Matrix for DS3/E3 ATM Network ModulesProduct IOS S/W Version Required IOS Feature Sets or LicensesRequiredMaximum supportedCisco 2800 Series (2811, 2821, 2851) 12.4(15)T All Cisco IOS12.4(15)T and above “SPServices” feature sets1Cisco 3825 12.4(15)T All Cisco 12.4(15)T and above “SPServices” feature sets1Cisco 3845 12.4(15)T All Cisco 12.4(15)T and above “SPServices” feature sets211Cisco 3925 15.0(1)M Data License 122Cisco 3945 15.0(1)M Data License 221 Maximum recommended modules does not imply will meet performance at wire rate2 Support for the DS3/E3 ATM network module in the 3925, and 3945 will be via the network module adapter card (SM-NM-ADPTR)Advanced Traffic ManagementAdvanced traffic management mechanisms in the DS3/E3 ATM network modules architecture allow for the support of bursty, client/server traffic, while supporting applications that require guaranteed or best-effort service. The ATM DS3/E3 supports all the ATM service classes, including UBR, UBR+, VBR-rt, VBR-nrt, and ABR. Supporting these ATM service classes allows the DS3/E3 network modules to concurrently support various network applications on the same ATM interface. VBR-rt is intended for applications that require guaranteed services, and ABR and UBR are intended for applications that need only “best-effort” service.The ABR support includes the Explicit Rate (ER), Relative Rate (RR), and Explicit Forward Congestion Indicator (EFCI) modes. ABR was defined specifically to minimize cell loss and maximize good put through the ATM network. Explicit Rate ABR is typically deployed in ATM WAN switches, and is used in products such as Cisco’s 8400/IGX and 8800/MGX ATM switches. Relative Rate ABR is more effectively deployed in the campus and is supported by the Cisco Lightstream 1010, and 8500 series ATM switches. EFCI is typically used for backward compatibility with legacy ATM switches that support neither Explicit nor Relative Rate. Please refer to Table 2 for ATM Service Class Definitions.Table 2. ATM Service Class DefinitionsATM Service Classes Typical UseVBR-nrt-non-real time Variable Bit Rate Used for all applications that require a level of Service guarantee through the ATM.VBR-rt-real-time Variable Bit Rate Used for connections that transmit at a rate varying with time and that can be described as bursty, oftenrequiring large amounts of bandwidth when active. Intended for applications that require tightlyconstrained delay and delay variation such as compressed VoIP and video conferencing.ABR-Available Bit Rate Used to maximize bandwidth utilization on the ATM link through the use of congestion feedbacknotification.UBR-Unspecified Bit Rate Most legacy data applications using fair best-effort service.CBR-Constant Bit Rate Provides guaranteed bandwidth for data applications such as SNA traffic.Per-VC Traffic ShapingTraffic shaping is a function typically provided on ATM edge devices to ensure that bursty traffic conforms to a predetermined Service Level Agreement (SLA). More specifically, traffic shaping ensures that traffic from one VC does not adversely impact another, resulting in data loss. This function is very important when connecting to an ATM WAN or public ATM network-especially when the ATM switches enable traffic policing that will discard all traffic that exceeds the predetermined contract at the ingress of the switch.The ATM DS3/E3 supports traffic shaping in hardware which eliminates performance degradation when shaping is enabled. Providing traffic shaping on a per-VC basis in done by the software using IP-to-ATM CoS mapping feature and allows total flexibly and control over every VC configured.For each ATM service class, the ATM DS3/E3 supports highly configurable parameters: peak cell rate (PCR), sustainable cell rate (SCR), maximum burst size (MBS) and minimum cell rate (MCR). These parameters can be defined based on the specific bandwidth requirements of an individual VC, as needed for a specific application. Table 3 lists ATM Class of Service Traffic Shaping Parameters supported on the product.Table 3. ATM Class of Service Traffic Shaping ParametersVBR -rt and nrt Parameters ABR Parameters UBR ParametersPCR (kbps) PCR (kbps) PCR (kbps)SCR (kbps) MCR (kbpsMBS (cells)The ATM DS3/E3 hardware “shapes” the VC to the specific parameters using a wheel-based scheduling algorithm to ensure fairness across the ATM interface. In the event that two cells compete for the same time slot, the VCs are prioritized in the following order (starting with highest priority): 1) CBR; 2)rt-VBR; 3)nrt-VBR; 3) ABR; and 4) UBR. OAM cells and signaling has the priority higher than any of the service classes. Prioritizing the VCs in this manner ensures that the high priority and guaranteed traffic have precedence over the best-effort traffic.To provide further flexibility, the ATM DS3/E3 allows each of these parameters to be set over a wide range of small increments. Please refer to Table 4 for the Traffic Shaping Granularity supported on this module.Table 4. Traffic Shaping GranularityParameter Range IncrementsPCR 64 kbps to line rate 64 kbpsSCR 64 kbps to line rate 64 kbpsOne cellMBS ●<32 up to 4 Mbps●<200 up to line rateNote: Although configuration to line rate is allowed, line rate is only reached with large packet sizes.Extended Virtual Connections CapabilitiesThe ATM DS3/E3 supports up to 1024 Virtual Connections (VC) and up to 256 Virtual Path (VP). Any combinations of VC and VP can be supported up to a maximum number of 1024 VC/VP combinations. These VCs can be either Permanent Virtual Connections (PVC) which are created manually or Switched Virtual Connections (SVC) created through point-to-point and point-to-multipoint UNI signaling. Table 5 provides Interface Specification details. Table 6 provides LED Indicator description.Table 5. Interface SpecificationsInterface Rate Connector Type Wavelength Maximum DistanceDS3 44.736 Mbps BNC Coaxial 450 ft.E3 34.368 Mbps BNC Coaxial 1250 ft.Note: The DS-3 version provides adaptive equalization for 0-450 ft. of cable and provides loopback capability. The E3 version provides adaptive equalization for 0-1250 ft. of cable and also provides loopback capabilities.The DS-3 version also has the ability to support line build-out for cable lengths of less than 50 ft. or greater than50 ft., as required.Table 6. LED IndicatorsATM NM LED Port Status FunctionEnable Green Indicates the ATM NM is successfully inserted and has established communications to the PCI bus. It isready to accept CLI commandsRCLK Green Indicates that a receive clock has been detectedFERF Yellow The framer has detected a Far End Receive FailureOOF Yellow The framer has detected an Out of Frame occurrenceAIS Yellow The framer has detected an Alarm Indication SignalSystem Requirements● A maximum of one NM-1A-T3/E3 Network Module is supported on the Cisco 2811,2821,2851 and 3845.Two are supported on the Cisco 3845. Line rate performance is not guaranteed for maximum NM-1A-T3/E3 Network Module support on the platforms.●Operates in conjunction with all currently available Cisco 3800 network modules and WAN interface cards(WICs) and with all currently available Cisco 3900 Network Modules, Service Modules, Internal ServicesModules, EHWICs, HWICs, WICs and VICs.●No slot placement restrictions●Support for the DS3/E3 ATM network module in the 3925, and 3945 will be via the network module adaptercard (SM-NM-ADPTR).Network ManagementSupported MIBs include:●Synchronous Optical Network (SONET) MIB●MIB II●AToM MIB (FRC 1695)●ILMI MIB●CISCO-BUS MIB●CISCO-LECS-MIB●CISCO-LES-MIB●LAN Emulation (LANE) MIB●Cisco-AAL5-MIB●DS3/E3 CISCO-ATM-IF-PHYS-MIBProduct Compliance StandardsThe DS-3 and E3 ATM network modules are to receive all the agency approvals necessary for unlimited international availability. The following regulatory approvals are supported:EnvironmentalTable 7. DS3/E3 ATM Physical SpecificationsProduct Specifications DescriptionsDimensions (H x W x D) 1.55 x 7.10 x 7.2 inWeight 2 lbs. MaximumEnvironmental Conditions ●Operating temp. 41-131°F (+5 -+55°C)●Non-operating temp. -13-158°F (-25-70°C)Relative Humidity 0 to 90%, noncondensingEMI Class B EMICabling 75 Ohm BNC type connectorLEDs Enabled, RX cells, RX carrier, RX AlarmSafety Regulatory Approvals●UL 1950 3rd edition/CSA C22.2, no. 950●C1950 (Canada)●AS/NZS 3260 (Australia/New Zealand)●EN60950 (Europe)●IEC 950 (National Deviations)Emission Regulatory Approvals●FCC Part 15J Class A (US/Canada)●VCCI Class 2 (Japan)●AS/NZS 3548 (Australia/New Zealand)●EN55022 (CISPR 22) Class B (Europe)Cisco and Partner Services for the BranchServices from Cisco and our certified partners can help you transform the branch experience and accelerate business innovation and growth in the Borderless Network. We have the depth and breadth of expertise to create a clear, replicable, optimized branch footprint across technologies. Planning and design services align technology with business goals and can increase the accuracy, speed, and efficiency of deployment. Technical services help improve operational efficiency, save money, and mitigate risk. Optimization services are designed to continuously improve performance and help your team succeed with new technologies. For more information, visit/go/services.。
思科 4000 系列 ISR 模拟语音网络接口模块说明书
产品手册适用于思科 4000 系列 ISR 的模拟语音网络接口模块 (NIM)在思科 4000 系列 ISR 上使用 NIM 支持多种语音应用简介思科® 4000 系列集成多业务路由器 (ISR) 支持使用思科网络接口模块 (NIM) 提高端口密度和模块容量，NIM 是增强版高速广域网接口卡 (EHWIC) 进一步演化的产物。
4000 系列 ISR 上最多提供三个集成 NIM 插槽，灵活地满足不同配置需求。
NIM 支持联机插拔 (OIR)，减少了安装新模块或更换旧模块所需的停机时间。
目前提供的 NIM 包括以下类型：2 端口和 4 端口外部交换站 (FXS) 模块、直接内拨 (DID) 模块、外部交换局 (FXO) 模块、2 端口 FXS 和 4 端口 FXO 组合模块、4 端口收发 (E/M) 模块，以及 2 端口和 4 端口基本速率接口 (BRI) 模块（见图 1）。
BRI 模块（卡）仅支持语音功能。
NIM 具备专用的数字信号处理器 (DSP)，用于处理时分复用(TDM) 模拟语音服务。
表 1 列出目前提供的模块。
注：思科 2900 和 3900 系列 ISR 不支持 NIM。
图 1.思科 4000 系列 ISR兼容的思科 FXO、FXS 和 2FXS/4FXO NIM表 1.思科 FXO 和 FXS NIM 类型及功能比较* 名称中包含“P”的版本是在制造流程中引入新的硬件组件后生产的，在功能上与名称中未包含“P”的版本并无不同。
FXS、FXO、E/M 和 BRI NIM 可在不关闭路由器的情况下，直接插入受支持的思科 4000 系列 ISR 的 NIM 插槽。
新一代思科 FXO/FXS NIM 在以前的广域网接口卡（VIC 和 VIC2）的基础上加入了许多增强功能。
FXO、FXS、E/M 和 BRI NIM 具有板载 DSP，因此无需在路由器主板上安装专用的分组语音 DSP 模块 (PVDM)。
Cisco各种模块及其详解
思科接口卡和模块产品详解鑫海网络商城 / 2008-04-08广域网网络模块/接口卡产品编号Cable HWICHWIC-CABLE-D-2 单端口基于DOCSIS的cableHWIC-CABLE-E/J-2 单端口基于Euro/J-DOCSIS 2.0的cable串行和异步HWIC HWIC-4T 4 端口串行高速WAN 接口卡HWIC-4A/S 4 端口异步/ 同步高速WAN接口卡HWIC-8A 8 端口异步高速WAN 接口卡HWIC-16A 16端口异步高速WAN 接口卡HWIC-8A/S-232 8 端口异步/ 同步高速WAN接口卡串行WICWIC-1T 单端口串行WICWIC-2T 双端口串行WIC带CSU/DSU的T1 WIC WIC-1DSU-T1-V2 单端口T1接口卡，带CSU/DSU BRI WIC WIC-1B-S/T-V3 单端口ISDN WICSHDSL HWICHWIC-2SHDSL G.SHDSL接口卡HWIC-4SHDSL G.SHDSL接口卡对称高比特率DSL WIC WIC-1SHDSL-V3 单端口G.SHDSL接口卡ADSL2和ADSL2 HWICHWIC-1ADSL 单端口非对称数字用户线路HWICHWIC-ADSL-B/STADSL WIC WIC-1ADSL 单端口非对称数字用户线路WICWIC-1ADSL-DG 单端口非对称数字用户线路WIC，带Dying Gasp支持WIC-1ADSL-I-DG 单端口ADSL over ISDN WIC，带Dying Gasp 支持V.90调制解调器WIC WIC-1AM 单端口模拟调制解调器HWICWIC-2AM 2端口模拟调制解调器HWIC3G无线HWICHWIC-3G-CDMAHWIC-3G-GSM网络模块/接口卡产品编号T3/E3网络模块(纯信道)NM-1T3/E3 单端口透明通道T3/E3 网络模块串行连接网络模块NM-1HSSI 单端口HSSI 网络模块NM-4T 4 端口串行网络模块NM-4A/S 4 端口异步/ 同步串行网络模块NM-8A/S 8 端口异步/ 同步串行网络模块NM-16A/S 16 端口异步/ 同步串行网络模块NM-16A- 16 端口异步网络模块NM-32A 32 端口异步网络模块ISDN PRI网络模块(第三代)NM-1CE1T1-PRI 单端口通道化E1/T1 ISDN PRI 网络模块NM-2CE1T1-PRI 2端口通道化E1/T1 ISDN PRI 网络模块ISDN BRI网络模块NM-4B-S/T 4 端口ISDN-BRI 网络模块NM-4B-U 4 端口ISDN-BRI 网络模块，带NT-1 NM-8B-S/T 8 端口ISDN-BRI 网络模块NM-8B-U 8端口ISDN-BRI 网络模块，带NT-1ATM OC-3 网络模块(第二代)NM-1A-OC3-POM 单端口ATM OC3接口模块，支持POM和SFPATM OC-3网络模块(第一代)NM-1A-OC3MM 单端口OC3 ATM 多模光纤网络模块NM-1A-OC3SMI单端口OC3 ATM 单模中距离光纤网络模块NM-1A-OC3SML单端口OC3 ATM 单模远距离光纤网络模块DS3/E3 ATM网络模块NM-1A-T3 单端口DS3 ATM网络模块NM-1A-E3单端口E3 ATM 网络模块ATM AIM (内部插槽)AIM-ATM ATM支持模块IP网络模块上的电路仿真NM-CEM-4TE1 4端口T1/E1电路仿真模块NM-CEM-4SER 4 串口电路仿真模块数字调制解调器网络模块NM-6DM 6 端口数字调制解调器网络模块NM-12DM 12端口数字调制解调器网络模块NM-18DM 18端口数字调制解调器网络模块NM-24DM 24端口数字调制解调器网络模块NM-30DM 端口数字调制解调器网络模块MMTL-3600 管理调制解调器的软件license MICA-6MOD 6 个数字调制解调器升级V.92模拟调制解调器网络模块NM-8AM-V2 8 端口模拟调制解调器网络模块，带V.92NM-16AM-V2 16端口模拟调制解调器网络模块，带V.92 IP VSAT卫星网络模块NM-1VSAT-GILAT IP VSAT卫星网络模块局域网网络模块/ 接口卡产品编号快速以太网HWICHWIC-1FE 1端口快速以太口WAN模块HWIC-2FE 2端口快速以太口WAN模块以太网交换机HWICHWIC-4ESW 4 端口10/100 交换机HWICHWIC-D-9ESW 9 端口10/100 交换机HWIC以太网交换机业务模块NME-16ES-1G-P 16端口以太交换服务模块，支持POE，带1个RJ45的10/100/1000以太网口NME-X-23ES-1G-P 23端口以太交换服务模块，支持POE，带1个RJ45语音（集中自动信息记帐）功能VIC-4FXS/DID 4 端口FXS语音/ 传真接口卡BRI语音接口卡(第二代)VIC2-2BRI-NT/TE 2 端口BRI语音/传真接口卡T1/E1语音接口卡(第二代)VWIC2-1MFT-T1/E1单端口第二代T1/E1Multiflex 中继语音/WAN接口卡VWIC2-2MFT-T1/E1 2端口第二代T1/E1Multiflex 中继语音/WAN接口卡T1/E1语音接口卡(第一代)VWIC-1MFT-T1 单端口RJ-48 Multiflex中继T1 语音/WICVWIC-2MFT-T1 2端口RJ-48 Multiflex中继T1 语音/WICVWIC-2MFT-T1-DI 2 端口RJ-48 Multiflex 中继T1语音/WIC，支持上行功能VWIC-1MFT-E1 单端口RJ-48 Multiflex中继E1 语音/WICVWIC-2MFT-E1 2端口RJ-48 Multiflex中继E1 语音/WICVWIC-2MFT-E1-DI 2 端口RJ-48 Multiflex中继E1语音/WIC，带上行功能网络模块/接口卡产品编号模拟/BRI语音网络模块(第二代)NM-HD-1V 单插槽IP通信语音/传真网络模块NM-HD-2V 2插槽IP通信语音/传真网络模块NM-HD-2VE 双插槽IP通信增强语音/传真网络模块高密度模拟语音网络模块NM-HDA-4FXS 高密度模拟语音/传真网络模块，带4FXS高密度数字/模拟语音网络模块NM-HDV2 高密度模拟语音/传真网络模块NM-HDV2-1T1/E1高密度模拟语音/传真网络模块,带1个E1/T1端口NM-HDV2-2T1/E1高密度模拟语音/传真网络模块,带1个E1/T1端口网络模块/接口卡产品编号语音基板扩展模块EVM-HD-8FXS/DID 高密度模拟和数字扩展模块，用于语音和传真，带8个可针对FXS 或DID 信令分别配置的端口EVM-HD模拟/BRI扩展模块EVM-HDA-8FXS 高密度模拟语音/传真网络模块，带8FXSEM-HDA-6FXO 6 端口FXO 语音和传真扩展模块EM-HDA-3FXS/4FXO 3 端口FXS 和4 端口FXO语音和传真扩展模块EM-4BRI-NT/TE 4端口语音和传真扩展模块NM-HAD模拟/BRI 扩展模块EM-HDA-8FXS 8 端口语音/ 传真扩展模块FXS EM-HDA-4FXO 4 端口FXO 语音和传真扩展模块EM2-HDA-4FXO 4 端口FXO 语音和传真扩展模块语音高级集成模块AIM-VOICE-30 AIM语音模块AIM-ATM-VOICE-30 AIM语音/ATM模块Return to Top安全性网络模块/接口卡产品编号面向集成多业务路由器的NAC 网络模块NME-NAC-K9 NAC网络模块NACNM-50-K9 NAC网络模块license-50用户NACNM-100-K9 NAC网络模块license-100用户NACNM-50UL= NAC网络模块升级license- 从50到100入侵防御系统高级集成模块AIM-IPS-K9 入侵防御系统高级集成模块面向ISR的USB eToken MEMUSB-64FT 64M的USB eToken MEMUSB-128FT 128M的USB eToken MEMUSB-256FT 256M的USB eTokenAIM-VPN PLUS-VPN加速卡AIM-VPN/BPII PLUSAIM-VPN/EPII PLUSAIM-VPN/HPII PLUSAIM-VPN/SSL-VPN加速卡AIM-VPN/SSL-1 AIM-VPN/SSL-2 AIM-VPN/SSL-3IDS网络模块NM-CIDS IDS网络模块Security Device Manager SDM 安全设备管理无线网络模块/接口卡产品编号3G WWAN HWIC HWIC-3G-GSM GSM 3G 模块HWIC-3G-CDMA-V CDMA的3G模块HWIC-3G-CDMA-S CDMA的3G模块无线局域网AP HWICHWIC-AP-G-x 802.11 B/G 接入点HWICHWIC-AP-AG-x 802.11 A/B/G 接入点HWIC无线局域网控制器模块NM-AIR-WLC6-K9 无线网络控制模块，可管理6个接入点NME-AIR-WLC8-K9 无线网络控制模块，可管理8个接入点NME-AIR-WLC12-K9无线网络控制模块，可管理12个接入点IP VSAT卫星网络模块NM-1VSAT-GILAT IP VSAT卫星网络模块Ret应用–业务网络模块/接口卡产品编号面向分支机构路由器的内容引NM-CE-BP 内容引擎网络模块擎网络模块面向分支机构路由器的网络分析模块NM-NAM 网络分析模块应用导向网络模块NM-AON-K9 应用导向网络模块数据压缩AIM AIM-COMPR4 16Mbps数据压缩集成模块语音应用模块AIM-CUE NM-CUE NM-CUE-EC广域应用业务(WAAS)模块NME-WAE-302-K9 广域网加速模块，80G/512MNME-WAE-502-K9 广域网加速模块，120G/1G Return to TopEoS/EoL模块网络模块/接口卡产品编号思科AIM-VPN-II-PLUS模块AIM-VPN/BPII-PLUS, AIM-VPN/BPII-PLUS=, AIM-VPN/EPII-PLUS, AIM-VPN/EPII-PLUS=, AIM-VPN/HPII-PLUS, AIM-VPN/HPII-PLUS=思科1端口DS3和1端口E3 ATM网络模块NM-1A-E3, NM-1A-E3=, NM-1A-T3, NM-1A-T3= 1端口POTS ADSL和ISDN ADSL广域网接口卡，带Dying GaspWIC-1ADSL-DG, WIC-1ADSL-I-DG思科2600/3600/3700系列ATM OC-3 155-Mbps 网络模块NM-1A-OC3MM, NM-1A-OC3MM=, NM-1A-OC3MM-EP, NM-1A-OC3MM-EP=, NM-1A-OC3SMI,NM-1A-OC3SMI=, NM-1A-OC3SMI-EP,NM-1A-OC3SMI-EP=, NM-1A-OC3SML,NM-1A-OC3SML=, NM-1A-OC3SML-EP, NM-1A-OC3SML-EP=1端口和2端口T1/E1多路传输语音/广域网接口卡VWIC-1MFT-E1 VWIC-1MFT-T1 VWIC-1MFT-G703VWIC-2MFT-E1 VWIC-2MFT-T1 VWIC-2MFT-E1-DI VWIC-2MFT-T1-DI VWIC-2MFT-G703对称高比特率DSL WIC WIC-1SHDSL, WIC-1SHDSL-V225Mbps ATM网络模块NM-1ATM-25IMA网络模块NM-4T1-IMA, NM-4E1-IMA, NM-8T1-IMA, NM-8E1-IMA ISDN PRI 网络模块(第二代)NM-1CT1, 2CT1NM-1CT1-CSU, 2CT1-CSU, NM-1CE1B, 2CE1-BISDN PRI 网络模块(第一代)NM-1FE1CT1, NM1FE2CT1, NM-1FE1CT1-CSU, NM-1FE2CT1-CSU, NM-1FE1CE1B, NM-1FE2CE1B, NM-1FE1CE1U, NM-1FE2CE1UV.92模拟调制解调器网络模块NM-8AM-J, NM-16AM-J NM-HDV DSP模块PVDM-12模拟语音接口卡(第一代)VIC-2FXS, VIC-2FXO, VIC-2FXO-EU,VIC-2FXO-M1/M2/M3, VIC-2E/M, VIC-2DID, VIC-2CAMABRI语音接口卡(第一代)VIC-2BRI-S/T-TE, VIC-2BRI-NT/TE J1语音接口卡VIC-1J1模拟/BRI语音网络模块(第一代)NM-1V, NM-2V数字T1/E1语音网络模块NM-HDV-1T1-12, NM-HDV-1T1-24, NM-HDV-1T1-24E, NM-HDV-2T1-48, NM-HDV-1E1-12, NM-HDV-1E1-30, NM-HDV-1E1-30E, NM-HDV-2E1-60数字J1 语音网络模块NM-HDV-1J1-30, NM-HDV-1J1-30EDSP群集网络模块NM-HDV-FARM-C36, NM-HDV-FARM-C54,NM-HDV-FARM-C90数据压缩AIM AIM-COMPR2-V2报警监控和远程控制网络模块NM-AIC-64以太网网络模块NM-1FE-FX NM-1FE-TX NM-1ENM-4EVPN/加密AIM AIM-VPN/HPII, AIM-VPN/EPII, AIM-VPN/BPII VPN/加密AIM AIM-VPN/HP, AIM-VPN/EP, AIM-VPN/BP带CSU/DSU的T1 WIC WIC-1DSU-T1, WIC-1DSU-56K4ISDN BRI WIC WIC-1B-S/T。
思科 Catalyst 4000 4500 系列千兆位以太网模块 说明书
产品简介Cisco Catalyst 4000/4500系列千兆位以太网模块概述Cisco Catalyst® 4000/4500系列可扩展模块化高密度交换机能够通过智能服务提供高性能的集成式第2层、第3层和第4层交换，因而能加强网络控制，并提高网络弹性。
这些交换机提供多种1000Mbps千兆位以太网模块，能够为千兆位服务器和台式机企业交换解决方案及电信运营商城域以太网提供光纤和铜线接口。
千兆位以太网交换模块不但包括基于1000BASE-X千兆位接口转换器（GBIC）的经济有效的高性能千兆位以太网线卡，还包括业界密度最高的48端口10/100/1000BASE-T三速自检测、自协商千兆位以太网线卡和系统。
产品说明铜线千兆位模块Cisco Catalyst® 4000/4500系列能够为布线室和服务器集群提供多种铜线千兆位解决方案，从而通过第5类铜线为台式机和服务器提供高密度千兆位连接。
如图1、图2所示，Cisco Catalyst® 4000/4500系列提供两种线卡，包括48端口10/100/1000BASE-T （WS-X4448-GB-RJ45）和24端口10/100/1000BASE-T（WS-X4424-GB-RJ45）模块。
图148端口线卡（WS-X4448-GB-RJ45）图224端口线卡（WS-X4424B-RJ45）48端口10/100/1000BASE-T线卡（WS-X4448-GB-RJ45）Cisco Catalyst 4000/4500系列48端口10/100/1000BASE-T线卡扩展了思科在模块化交换式以太网市场上的领先地位，能够提供从网络边缘直接到台式计算机的业界密度最高的自协商千兆位以太网。
这种线卡为48个RJ-45端口提供三速自检测、自协商技术，使所有端口都能通过第5类电缆提供10Mbps、100Mbps或1000Mbps的速度，以及100米的最大距离，并提供最大的灵活性和投资保护。
认识思科路由器接口及模块
认识思科路由器接口及模块认识思科路由器接口及模块
1.接口的概述
1.1 什么是接口
1.2 接口的作用
1.3 接口的分类
2.路由器接口种类
2.1 以太网接口
2.2 串行接口
2.3 网络接口卡（NIC）接口
2.4 无线接口
2.5 其他特殊接口
3.接口模块的介绍
3.1 接口模块的作用
3.2 接口模块的安装与配置
4.接口配置命令
4.1 接口激活与停用命令
4.2 接口描述命令
4.3 接口IP地质配置命令
4.4 接口速率和双工模式配置命令
4.5 接口带宽分配命令
5.接口状态检查与故障排除
5.1 检查接口状态的命令
5.2 故障排除的常见方法
6.附件
附件1、思科路由器接口配置示例
附件2、接口配置常见问题解决方案
法律名词及注释:
1.接口: 在计算机网络中，接口是指不同硬件或软件之间的连接点，用于数据在这些设备之间的传输和交换。
2.以太网: 一种计算机局域网技术，基于IEEE 802.3标准，用于在局域网内进行数据通信。
3.串行接口: 一种用于数据传输的接口，将数据位按照顺序依次传送，比如串行端口、串行总线等。
4.网络接口卡（NIC）: 用于将计算机与网络连接的硬件设备，负责将计算机的数据转换为网络可以识别的信号。
5.无线接口: 用于无线通信的接口，常见的有Wi-Fi、蓝牙等无线接口。
6.思科路由器: 思科公司生产的一种网络设备，用于在不同网络之间传递和转发数据包。
本文档涉及附件：附件1、思科路由器接口配置示例，附件2、接口配置常见问题解决方案。
思科STM-1技术与模块配置介绍
思科STM-1技术与模块配置介绍STM-1介绍一，什么是STM技术STM，Synchronous Transport Module，是基于电信SDH骨干网传输的一种时分复用技术，与CE1线路很类似。
说的简单点，一个STM模块就是一个多通道的E1模块。
一个STM 模块可以配置为最大支持63个E1线路，而每一个E1线路可以根据用户的需要配置为2M 的带宽，或者再细分成N×64K的channel－group的形式。
根据ITU－T的G。
703的定义，国际上流行的STM复用技术主要以下两种：a,E1――C-12――VC-12――TU-12x3――TUG-2x7――VC-3――AU-3--x3――AUG――STM-1b,E1――C-12――VC-12――TU-12 x3――TUG-2 x7――TUG-3 x3――VC－4――AU－4－AUG――STM-1TU-12 x3：一个就是1个E1也就是2M。
TUG-2 x7：7个TUG-2等于一个TUG-3TUG-3x3：3个TUG-3等于一个AU4AU4：一个AU4等于155M目前中国的电信多采用第二种复用路径，一般习惯成为373复用,简单的理解，一个E1的祯首先被装进一个叫做C-12的容器，再被装进VC-12的容器，然后形成一个叫做附属单元的东东（tu-12），然后三个tu-12被复用成一个附属单元组tug-2，接下来7个tug-2被复用成一个更大的单元组，叫做tug-3，后面再用一个叫做VC-4的更大的容器装下3个tug-3，转换为一个au-4,在经过转化，最后成为STM的祯格式（有点晕：（）。
在给客户安装时需要注意：1，一块STM－1模块最多只能划分256个channel group。
2，有些高版本的IOS并不支持STM卡，如果装上去无法识别，可以适当的调整IOS的版本。
二，PA-MC-STM-1的配置由于电信提供的STM/E1的服务是基于SDH这种透明的传输技术的，所以STM的配置很简单，而且很多参数可以我们自己定制，而不需要电信提供，比如E1的数据祯是否成祯，具体成祯的格式等等。
Cisco路由器接口与模块简介
Cisco路由器接口及模块简介本文以思科公司最通用、最典型的路由器型号——Cisco2600系列为例来进行说明。
思科在早期的路由器（如Cisco2500系列）中，接口都是固定化设计，从Cisco2600系列起，开始采用模块化设计，部分接口（接口卡和网络模块）将由客户根据自己的需要来选购，这使得思科的路由器产品具有极强的升级和扩展能力。
思科公司的Cisco2600系列路由器具有企业级的通用性、集成性和扩展性。
随着企业新应用的出现，这个系列的模块化结构能适应网络技术的变化，能通过更换接口卡和网络模块进行升级。
Cisco2600系列配置了强大的RISC处理器，能够支持高级服务质量（QoS）、安全和网络集成等多种服务。
Cisco2600系列与Cisco1600、1700和3600系列共享模块化接口，为Internet、部网访问、语音/数据集成、模拟和数字拨号访问服务、VPN访问、ATM访问、VLAN以及路由管理等提供全面的解决方案。
这个系列的路由器是目前中小企业使用得最多的路由器型号，完全有能力适应中小企业不断发展的网络应用需求，虽然它被思科公司定义为“使用在中小企业分支机构里”，但是对于需求不是很高级的用户往往把它用在网络的核心。
思科的Cisco2600系列包括：2610、2611、2613、2620、2621、2650、2651（以上型号思科公司在全球已经停止出销售）和2610XM、2611XM、2612、2620XM、2621XM、2650XM、2651XM、2691（正在销售）（见图1）。
表1为正在销售的Cisco2600XM和2612、2691的接口基本配置。
在Cisco2600系列中，有些接口是固化，而有些接口是模块化设计，被用户选购来安装在广域网接口插槽和网络模块插槽里。
固定化配置的接口有：辅助口（AUX）和控制口（CON）都各有一个；以态网口（ETHERNET）会有一个到两个；令牌环（TR）只有在Cisco2612、Cisco2613中有一个。
思科spa500s扩展模块数据表说明书
Data SheetCisco SPA500SExpansion ModuleHighlights●Easy to install, and designed exclusively for the Cisco ®SPA 500 Series IP Phones ●32 programmable buttons simplify dialing and call transfers ●Multicolored LEDs monitor the status of each configured voice line via Busy Lamp Field (BLF) ● Two attendant consoles can be linked, for a total of 64 buttons Figure 1. Cisco SPA500S Expansion ModuleProduct OverviewThe Cisco ®SPA500S Expansion Module (Figure 1) is part of the Cisco Small Business Pro Series and designed for use with the Cisco SPA500 Series IP Phones. It is an ideal solution for small businesses wanting to simplifyincoming call handling by quickly directing calls to the requested party and also to monitor line status from a central location.The attendant console easily attaches to a SPA500 Series IP Phone, providing 32 programmable speed-dial or direct station select (DSS) buttons, each illuminating the line’s status (idle, ringing, busy, or null) via the BLF. Incoming calls can immediately be transferred to the proper location with the push of a button assigned to the extension.The modular design of the Cisco SPA500S permits up to two attendant consoles to be deployed, for a total of 64 buttons, offering an affordable solution that expands with the growth of your voice network. Installation and setup is just a matter of connecting the supplied bracket and cable to the attendant console, which uses the phone’s power supply; no additional power source is required.Based on the Session Initiation Protocol (SIP), the Cisco SPA500S has been tested to ensure comprehensive interoperability with equipment from voice over IP (VoIP) infrastructure leaders, enabling service providers to offer competitive, feature-rich services to their customers.Features●32 programmable multicolored LED buttons●Illuminated line status monitoring (green for idle, red for in use, blinking red for ringing, orange for registrationerror)●Call transfer●Speed dial●DSS●Busy lamp field●One-touch transfer●Call pickupSpecificationsTable 1 contains the specifications, package contents, and minimum requirements for the Cisco SPA500S Expansion Module.Table 1. Specifications for the Cisco SPA500S Expansion ModuleSpecificationsPorts 2 auxiliary portsButtons 32LEDs Multicolored: green, red, orangeDocumentation ●Quick Installation Guide●User Guide●Administration Guide●Provisioning Guide (for service providers only)EnvironmentalDimensions W x H x D 4 x 8.5 x 1.5 in. (101 x 201 x 39 mm)Unit weight 2 lb (0.9 kg)Power Provided by host Cisco SPA 500 Series IP phoneCertification FCC, cUL, CE, Canadian Interference-Causing Equipment Standard ICES-003 Operating temperature 41º to 113ºF (0º to 40ºC)Storage temperature –13º to 185ºF (–40º to 70ºC)Operating humidity 5% to 95% noncondensing, operating and nonoperatingStorage humidity 5% to 95% noncondensing, operating and nonoperatingPackage Contents●Cisco SPA500S Expansion Module●Attachment arm●Two attachment arm screws●Auxiliary cable●Desktop stand●Quick Installation GuideMinimum Requirements●Cisco SPA500 Series IP PhoneService and SupportThe Cisco Small Business Support Service provides three years affordable peace of mind coverage, to help protect your investment and derive maximum value from your Cisco Small Business solution. The subscription-based service offers software updates, telephone and online chat access to the Cisco Small Business Support Center, and next business day hardware replacement.Cisco Small Business products are supported by professionals in Cisco Small Business Support Center locations worldwide who are specifically trained to understand your needs. The Cisco Small Business Support Community, an online forum, enables you to collaborate with your peers and reach Cisco technical experts for support information.WarrantyThis Cisco Small Business product is covered by a Cisco 1-year limited hardware warranty with return to factory replacement and a 90-day limited software warranty. In addition, Cisco offers software updates for bug fixes for the warranty term, and telephone and online chat technical support at no charge for the first 12 months following the date of purchase. To download software updates, go to: /cisco/web/download/index.html.Product warranty terms and other information applicable to Cisco products are available at/go/warranty.For More InformationTo learn more about the Cisco SPA 500 Series IP Phones please visit: /go/500phones.To learn more about Cisco Solutions for Small Business please visit /smallbusiness.。
第周围 思科常见接口卡和模块产品详解
以太网交换机网络模块
局域网和 WIC Combo 网络模块
网络模块 / 接口卡
千兆以太网 HWIC
千兆以太网网络模块
以太网/令牌环混合的介质网 络模块
语音 DSP 卡 网络模块/接口卡 回音消除
1751/1760 DSP 模块
10/100/1000 以太网口
NME-X-23ES-1G-P 23 端口以太交换服务模块，支持 POE，带 1 个 RJ45 的 10/100/1000 以太网口
NM-32A 32 端口异步网络模块
ISDN PRI 网络模块(第三代)
NM-1CE1T1-PRI 单端口通道化 E1/T1 ISDN PRI 网络模块 NM-2CE1T1-PRI 2 端口通道化 E1/T1 ISDN PRI 网络模块
对全部高中资料试卷电气设备，在安装过程中以及安装结束后进行高中资料试卷调整试验；通电检查所有设备高中资料电试力卷保相护互装作置用调与试相技互术关，通系电1，力过根保管据护线0生高不产中仅工资22艺料22高试可中卷以资配解料置决试技吊卷术顶要是层求指配，机置对组不电在规气进范设行高备继中进电资行保料空护试载高卷与中问带资题负料22荷试，下卷而高总且中体可资配保料置障试时23卷，23调需各控要类试在管验最路；大习对限题设度到备内位进来。行确在调保管整机路使组敷其高设在中过正资程常料1工试中况卷，下安要与全加过，强度并看2工且55作尽22下可2都能护1可地关以缩于正小管常故路工障高作高中；中资对资料于料试继试卷电卷连保破接护坏管进范口行围处整，理核或高对者中定对资值某料，些试审异卷核常弯与高扁校中度对资固图料定纸试盒，卷位编工置写况.复进保杂行护设自层备动防与处腐装理跨置，接高尤地中其线资要弯料避曲试免半卷错径调误标试高方中等案资，，料要编5试求写、卷技重电保术要气护交设设装底备备4置。高调、动管中试电作线资高气，敷料中课并3设试资件且、技卷料中拒管术试试调绝路中验卷试动敷包方技作设含案术，技线以来术槽及避、系免管统不架启必等动要多方高项案中方；资式对料，整试为套卷解启突决动然高过停中程机语中。文高因电中此气资，课料电件试力中卷高管电中壁气资薄设料、备试接进卷口行保不调护严试装等工置问作调题并试，且技合进术理行，利过要用关求管运电线行力敷高保设中护技资装术料置。试做线卷到缆技准敷术确设指灵原导活则。。：对对在于于分调差线试动盒过保处程护，中装当高置不中高同资中电料资压试料回卷试路技卷交术调叉问试时题技，，术应作是采为指用调发金试电属人机隔员一板，变进需压行要器隔在组开事在处前发理掌生；握内同图部一纸故线资障槽料时内、，设需强备要电制进回造行路厂外须家部同出电时具源切高高断中中习资资题料料电试试源卷卷，试切线验除缆报从敷告而设与采完相用毕关高，技中要术资进资料行料试检，卷查并主和且要检了保测解护处现装理场置。设。备高中资料试卷布置情况与有关高中资料试卷电气系统接线等情况，然后根据规范与规程规定，制定设备调试高中资料试卷方案。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
24 个10/100mbps以太网端口+2个SFP模块
插 Ca槽ta，lys标t 3准75多0 层24镜10像/100 P低oE密+度2接SF入P具St有an交da换rd机Im叠a加ge功能以及一或多条24光个纤10上/1行00链m路bp。sPoE端口+2个SFP模块插
槽 Ca，ta标lys准t 3镜75像0 48 10/100 + 4低S密FP度S接tan入d具ar有d M交u换lti机lay叠er加Im功a能ge poe以及4一8或个多10条/10光0m纤b上ps行以链太路网。端口+4个SFP模块
聚 Ca配ta线lys间t 3交75换0 机24，10带/1光00纤/10连00接T和St堆an叠da功rd能M。ultilayer Image
24 个10/100/1000mbps以太网端口，标准多层
镜 Ca像talyst 3750 24 10/100/1000 + 4 SFP + IPB Image; 1RU
插 Ca槽ta，lys标t 3准75多0 层48镜10像/100 Po中E 等+ 4 SFP Standard Image
48 个10/100mbpsPoE端口+4个SFP模块插
槽 Ca，ta标lys准t 3镜75像0 12 SFP Standard中M等ultilayer Image
12个SFP模块插槽，标准多层镜像 用于汇
24 个10/100mbps以太网端口+2个双重用途上行端口
（ Ca1t0a/l1y0st0/219060002b4as1e0_/t1或00者+ S2F1P0插00槽BT）LLAANNBBaasseeI镜m像age
24个10/100mbps以太网端口+2个10/100/1000base_t
上 Ca行ta端lys口t 2L96A0N48Ba1s0e/1镜00像+ 2 T/SFP LAN Base Image
24 个10/100mbps以太网端口+2个SFP模块插槽，标
准 Ca镜ta像lyst 3560 2低4 密10度/10第0 二Po层E 或+ 2第S三FP层S特tan征d以ar及d I一m或age多条光纤2上4 个行1链0/路10。0mbpsPoE端口+2个SFP模块插槽，标准
镜 Ca像talyst 3560 4低8 密10度/10第0 二+ 4层S或FP第S三tan层d特ar征d Imapgoee 以及一或多4条8个光1纤0/上100行m链bp路s以。太网端口+4个SFP模块插槽，标
产品
2918系列交换机
WS-C2918-24TT-C WS-C2918-24TC-C WS-C2918-48TT-C WS-C2918-48TC-C
2960系列交换机
WS-C2960-24TC-L WS-C2960-24TT-L WS-C2960-48TC-L WS-C2960-48TT-L WS-C2960G-24TC-L WS-C2960G-48TC-L 3560系列交换机 WS-C3560-24TS-S WS-C3560-24PS-S WS-C3560-48TS-S WS-C3560-48PS-S WS-C3560G-24TS-S WS-C3560G-24PS-S WS-C3560G-48TS-S WS-C3560G-48PS-S 3750系列交换机 WS-C3750-24TS-S WS-C3750-24PS-S WS-C3750-48TS-S WS-C3750-48PS-S WS-C3750G-12S-S WS-C3750G-24T-S WS-C3750G-24TS-S1U WS-C3750G-24PS-S WS-C3750G-48TS-S WS-C3750G-48PS-S 45，65核心系列交换机 WS-C4503 WS-C4506 WS-C4507R WS-C4506-E WS-C4507R-E WS-C4510R WS-C6506-E WS-C6509-E ASA系列自防御系统 ASA5505-K8
准 Ca镜ta像lyst 3560中4等8 1密0/度10第0 P二oE层+或4第SF三P层St特an性da以rd及Im一a或ge多条光纤4上8个行1链0/路10。0mbpsPoE端口+4个SFP模块插槽，标
准 Ca镜ta像lyst 3560 24中10等/1密00度/10第00二T层+ 或4 S第FP三S层ta特nd性ardpIome a以ge及一或多24条个光10纤/1上00行/10链00路m。bps以太网端口+4个SFP模块
48 个10/100mbps以太网端口+2个双重用途上行端
口 Ca（ta1ly0s/t10209/61004080b1a0s/e1_0t0或Po者rtSsF+P2）1L00A0NBTBaLsAe镜N像Base Image 48个10/100mbps以太网端口+2个10/100/1000base_t
上 Ca行ta端lys口t 2L96A0N24（1局0/1域00网/1）00B0a, s4eT镜/S像FP LAN Base Image
描述
接入层
CCaattaallyysstt 22991188 2244 1100//110000 ++ 22T1/0S0F0PBT （10/100/1000base_t 或者SFP）
CCaattaallyysstt 22991188 4488 1100//110000 ++ 22T1/0S0F0PBT （10/100/1000base_t 或者SFP）
块 Ca插ta槽lys，t 3标75准0 镜48像10/100/1000低T +密4度S第FP二S层tan或d第ard三M层u或lti以lay太er网汇聚具4有8 堆个叠10功/10能0/，10p0o0em和bp光s以纤太上网行端链口路+4个SFP
模 Ca块ta插lys槽t 3，75标0 准48多10层/1镜00像/1000T中P等oE密+度41S0F/1P00S/t1a0n0d0a接rd入Im，apgoee 第二层48或个第10三/1层00特/10性00以m及bp一sP或oE多端条口光+纤4个上S行FP链模路
ASA5505-BUN-K9 ASA5505-50-BUN-K9 ASA5505-UL-BUN-K9 ASA5505-SEC-BUN-K9 ASA5510-K8 ASA5510-BUN-K9 ASA5520-K8 ASA5520-BUN-K9 ISR系列路由器 CISCO1841 CISCO2801 CISCO2811 CISCO2821 CISCO2851 CISCO3825 CISCO3845 AIR无线系列 AIR-AP1131AG-C-K9 AIR-LAP1131AG-C-K9 AIR-AP1231G-A-K9 AIR-AP1231G-E-K9 AIR-AP1242AG-C-K9 AIR-LAP1242AG-C-K9 AIR-BR1310G-A-K9 AIR-WLC2106-K9 AIR-WLC4402-12-K9 AIR-WLC4402-50-K9 AIR-WLC4404-100-K9
块插槽，标准镜像
中等密度第二层或第三层或以太网汇聚，具有叠加功能和poe和光纤上行链路
Catalyst 4500 Chassis (3-Slot),fan, no p/s Catalyst 4500 Chassis (6-Slot),fan, no p/s Catalyst 4500 Chassis (7-Slot),fan, no p/s, Red Sup Capable Cat4500 E-Series 6-Slot Chassis, fan, no ps Cat4500 E-Series 7-Slot Chassis, fan, no ps, Red Sup Capable Catalyst 4500 Chassis (10-Slot),fan, no p/s,Red Sup Capable Catalyst 6500 Enhanced 6-slot chassis,12RU,no PS,no Fan Tray Catalyst 6500 Enhanced 9-slot chassis,15RU,no PS,no Fan Tray
在以T1（帧中继）/E1
（ 280租1赁w/线AC）PAWDSRL,2（FE通,4过sl广ots域(2网HW接I口C)提,2P供VADDMS,L2AoIvMer,IpPoBtsA和SAED,6S4LF/1o2v8eDr ISDN端口交）流广电域网2速个率FE运（行快服速务以时太，
网 281）1 w4个/ A接C口P卡W插R,2槽F（E,42HHWWIICCs都,2支PV持DHMWs,1ICNMWEIC,2AVIIMCSV,IWPIBCA模SE块,64一F/个25支6D持WIC VI交C 流或电VW2I个C类FE型(两模个块快一速
24个10/100/1000mbps以太网端口+4base_t 或者
SCFaPta上ly行st 端29口60 L48A1N0/（10局0/1部00区0,域4网T络/SF）PBLasAe镜N B像ase Image 48个10/100/1000mbps以太网端口+4base_t 或者
SFP上行端口
汇 Ca聚ta层lyst 3560 24 10/100 + 2 SFP Standard Image
块 Ca插ta槽lys，t 3标56准0 镜48像10/100/1000T PoE + 4 SFP Standard Image
48 个10/100/1000mbpsPoE端口+4个SFP模块
插槽，标准镜像
核 Ca心ta层lyst 3750 24 10/100 + 2 SFP Standard Multilayer Image
ASA 5505 Appliance with SW, UL Users, 8 ports, 3DES/AES