模具零件中英文对照表

常用模具零件中英文对照表

常用模具零件中英文对照表2005-12-19 14:51:17???中国注塑网入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis :?[??n?l?s?s]流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边：guide pin顶针板：ejector retainer plate托板：support plate螺丝： screw管钉：dowel pin ['da??l]开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate ?[?str?p?r] 脱漆剂；脱衣舞演员；剥离剂；剥离器缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock?['na?.lɑn]:斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞:pipeplug锁模块：lockplate斜顶：anglefrompin斜顶杆：angleejectorrod尼龙拉勾：partinglocks活动臂：leverarm复位键、提前回杆：earlyreturnbar气阀：valves斜导边：anglepin术语：terms承压平面平衡：partingsurfacesupportbalance模排气：partinglineventing回针碰料位：returnpinandcavityinterference模总高超出啤机规格：moldbaseshuthight顶针碰运水：waterlineinterfereswithejectorpin料位出上/下模：partfromcavith(core)side模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate.不准用镶件：Donotuse(core/cavity)insert用铍铜做镶件：useberylliumcopperinsert初步（正式）模图设计：preliinary(final)molddesign反呵：reversecore弹弓压缩量：springcompressedlength稳定性好：goodstability,stable强度不够：insufficientrigidity均匀冷却：evencooling扣模：sticking热膨胀：theroexpansion公差：tolorance铜公(电极）：copperelectrode塑件模具相关英文词汇出处：FanE『翻译中国』作者：(转载) FanE『翻译中国』 2005-12-16 20:41:59electrical discharge machining (EDM) 电火花加工15. electrical insulating property 电绝缘性能16. electrochemical die-sinking machine 电解型腔加工机，电解型腔加工机床17. electrochemical machine (ECM) 电解加工机床，电化学加工机床18. electrochemical machining (ECM) 电解加工，电化学加工19. electro-discharge cutting 电火花加工，电火花切割20. electro-discharge cutting machine 电火花切割机21. electro-discharge machine tool 电火花加工机床22. Electro-discharge Machine 电火花加工机床23. electro-discharge machining 电火花加工24. electro-discharge machining process 电火花加工工艺，电火花加工工序25. epoxy resin 环氧树脂9. guide bushing 导套10. guide pillar 导柱，导杆，导柱11. guide pin 导向销，导杆12. guide pin cover 导柱盖13. guide plate 导料板，导板14. guide plate blanking die 导板式冲裁模，导板式落料模15. guide post 导柱，导柱16. guide stock plate 挡料板4. injection mold 注射模，注塑模5. injection molding 注射成型，注塑成型6. injection-molding machine 注塑机，注射机，注塑成形机7. injection plunger 注射柱塞8. in-line reciprocating screw 联机往复螺杆，串联往复螺杆，直线排列往复螺杆9. inner ram 内滑块10. inserting molding 嵌件成形11. integrated manufacturing 集成制造12. internal stress 内应力13. intermediate platen 中间板，隔板塑料成型模具的主要设计要素脱模距 stripper distance脱模斜度 draft投影面积 projected area最大开距 maximum daylight;open daylight闭合高度 mould-shut height抽芯距 core-pulling distance抽芯力 core-pulling force脱模力 ejector force开模力 mould opening force模内压力 internal mould pressure;cavity pressure成型压力 moulding pressure背压环 back-up ring1 bar =高压接头 bite type fitting液压马达 hydraulic motor冷却水流量计 waterflow regulator打磨器材 abrasive material打磨砂轮 grinding wheels切割砂轮 cutting wheels码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具 piping tools高压力软管 high pressure hose风管,水软管 air .water hose高压油表 pressure gauge压力油喉 hydraulic hoses光塑检测 photoelastic testing吹塑模 plastic blow mould注塑模 plastic injection mould冲扎复合模 blank & form compound die精密冲模 precision blanking die熔料流动率 MFR=melt flow rate熔料流动指数 MET=melt flow index推板导柱 guide pin for ejector plater座板 clamping plate垫块 space block(plate)推板 ejector block(plate)afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件stage ejector 顶棍spacer rock(risers) 间隔板变形 distortion弯曲 warp拖花 drag marks火花纹 EDM marks困气 venting烧黑 burns表面缩水 shrinkage料位过薄/砸穿 thin wall stock走水不平行 uneven fill pattern夹水纹/流纹 witness line;mismatch;stress marks 走水纹 knit lines走水不齐 short shotsorifice 料口nozzle seat 热嘴垫圈nozzle plate 射嘴板cross pin 十字头销sled 射台seal ring 封密圈spacer rail 介子座heater groove 发热管槽heater cement 发热管的结合剂soak 浸泡seat 垫圈ream 铰大圆孔直径grind 磨床drill 钻床mill 铣床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚计hardness tester 硬度计angle gauge 角规marble table 云台石projector 投影仪height gauge 高度仪microscope 显微镜plug gauge 塞规leveller 水平器R gauge R 规Inter caliper 内分厘卡surface 平面仪item number 细目编码catalog number 材料分类编码undercut lip 倒扣口hot tip = hot drop = nozzle 热嘴blow-off strip 放气板blow-off nozzle 吹风口spiral hose 螺旋式的连接喉rust solvent 除锈剂shaft 曲轴tensile strength 拉伸力yield strength 屈服力spark erosion 电火花蚀刻etch(photo-etch) 电蚀harden 淬硬copper electrode 铜公corrosion resistance 耐腐蚀anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域reverse taper 倒啤把clamp plate 码板toggle clamp 快速夹vacuum furnace 真空炉cavity insert rounds 圆柱镶件cavity insert b0locks 方柱镶件tensile strength 抗张强度,抗拉强度Concept drawing 概念图Assembly drawing 装配图mismatch;witness line 夹纹shut-off(n.) 枕位venting valves 疏气阀venting plug 疏气塞valve casing 阀门罩twist drill 旋钻harden/nitride 碎硬anneal 退火temper 回火stess crack 应力断裂corrosion resistance 防腐,防锈tensile strength 物】抗张强度,抗拉强度split mould (分离)组合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,机械等)夹住东西的部分,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位clean-up 清理,清除,清扫Mold Dating Insert 模具日志镶件Hot Sprue Bushing 热浇口套semi-automatic 半自动quick disconnector 快速断开接头full shot 足量注射mismatch 夹痕;夹水纹ejector mark 顶痕screw boss 螺丝孔,螺丝基座sink mark 缩坑15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂drag mark 拖痕stress mark 应力痕reinforcement rib 加强筋slght stoning 轻度磨砂soliid line 实线dotted line 虚线internal diameter 内径external diameter 外径nickel-plated 电镀的handling hole;lifting hole 吊装孔parallel 平行块piston 活塞plunger 柱塞carrier 导轨rest 支架item number 项目编号catalog item 商品目录编码dimensional datum 尺寸基准heat treatment certification 淬硬证明文件back-up bushing 支撑导套jacking screw 起重螺丝,千斤顶tapped hole (带有螺旋角度的)螺丝孔diagonal corner 成对角的角落burn mark 烧痕hot runner mainfold (热流道板)分流板texuring 蚀纹clamping screw (注塑机)码模螺丝imperial 英制的metric 公制的puller bushing 水口套puller bar 水口铁drool bushing 防漏胶套筒safety switch 限位制water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件gate shut-offs 流道开关配件guided ejection 中托司parting line shutoff 前后模接触面waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱.BGV=Balanced Gate Value 平衡入水值spacer 垫块pocket 挖槽rough 粗加工finish 精加工plunge rate 进刀率retract rate 提刀速率splindle rate 主轴转速coolant 冷却液SPLIT RING 开口环(钥匙圈)侧向抽芯力 side pulling-core force转图guide pin 边针Tee slot cutter T形SLOT CUTTERzigzag 双向切削constant overlap spiral 等距环切parallel spiral 环绕切削parallel spiral clean corners 环切并清角morph spiral 依外形环绕true spiral 螺旋切削one way 单向end mill 平铣刀spher mill 球刀bull mill 圆鼻刀face mill 面铣刀rad mill 圆角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔铣刀dove mill 鸠尾铣刀lot mill 棒状drill 钻孔reamer 纹刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心钻spot drill 点钻cntr bore 沉头孔刀c. sink 鱼眼孔钻loft surface 举升曲面coons surface 昆氏曲面ruled surface 直纹曲面revolved surface 旋转曲面swept surface 扫描曲面draft surface 牵引曲面grinding wheel 磨砂使用的轮子quench steel 将...淬火,使冷却stress relieving 应力消除molten 熔热的oxide film 氧化层guide pin and sleeve, locating ring ,导边,司筒,定位圈ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒, lifters, wear plate,horn pin,斜坊,磨损板,气顶针,O ring, water baffle, water pipe plug,O形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板air cylinder,hydraulic cylinder,氯压缸,液压缸micro switch,oil nipple, spring,开关装置,油枪接头,弹弓sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cycle counter,date stamper，滑块固定板,生产日期铭牌,hot runner system ，热流道系统chemical composition 化学成份thermal conductiivity 导热性能thermal diffusivity 热扩散性能dimensonal stablity 尺寸稳定性能cooling effiency 冷却效率easiler ejection 易于脱模alloy insert 合金镶件(cooling) duct 输送管;导管maintenance cost 维护费用ultrasonic testing 超声波检测crack 断裂direct gate 直接浇口ring gate 环形浇口disk gate;disphragm gate 盘形浇口spoke gate;spider gate 轮辐浇口pin-point gate 点浇口edge gate 侧浇口submarine gate;tunnel gate 潜伏浇口fan gate 扇形浇口tab gate 护耳浇口runner plate 流道板(或冷或热)secondary nozzle 二级喷嘴torpedo;torpedo body assembly 鱼雷形组合体catridge heater 管式加热器heat pipe 热管valve gate 阀式浇口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活动镶件cavity splits;core splits(凹模拼块) (型芯拼块) 拼块side core 侧型芯thread plug;threaded core 螺纹型芯thread ring;threaded cavity 螺纹型环cutting wheel 切割砂轮grinding wheel 打磨砂轮abrasive material 打磨器材mould clamps;lifting clamp 砂模夹(注塑机使用)air (water) hose 风管,水轮管pressure gauge 高压油表hydraulic hose 压力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 冲扎复合模precisiion blanking die 精密冲模MFR=melt flow rate 熔料流动率MFT=melt flow index 熔料流动指数handling hole 拉铃孔stop plate 限位块linder bush 衬套spacer block(plate) 垫块,方铁back-up ring 背位环standoff 限位块American Safety Hoist Rings. 英制安全吊装环Mechanical Properties 机械性能Tensile Strength(MPa) 抗拉强度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 冲韧性Physical Properties 物理性能solidification shrinkage 凝固收缩率freezing range 凝固与熔范围thermal expansion 热膨胀系数specific heat 比热thermal conductivity 热导率electrical conductivity 电导率micro-structure 金相分析hot work tool steel 热作钢circular motion 环形运动variable 变数,参数graphics window 图形窗口45 degree entry and a zero degree exit. 进刀口45度,退刀口0度runner stripper plate 脱料板stripper plate 活动板spacer rock(risers) 间隔板stage ejector 顶棍sprue puller insert 扣针导套guide strip 行位后板afdek plate 挡尘板side gate 大水口pinpoint gate 细水口SHCS 杯头螺丝FHCS 平头螺丝set screw 无头螺丝ball catch 波子螺丝wedge 行位较杯gib 线条,(撑鸡的导轨)latch 拉杆clamp 码仔spring guide pin 弹弓导柱steel pad disc 橙仔方ejector cam insert 斜顶块(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把锁texture 花纹toggle-lok 回撞装置top clamping plate 顶码板unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙) set screw 喷头螺丝side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 弹弓座sprue puller 勾针/勾粒spring washer 弹簧塑圈stepped ejector pin 有托顶针strippers plate 推板/细水口板submarine gate 潜水口support pin 拉杆support plate 暗板surface finish 光洁度alignment strip 斜锁angle pin 斜针fan gate 扇形入水fillet 圆口ball catch 弹弓波子blade ejector 扁顶bottom clamping plate 底码板free length 自然长度bridge piece 水口铁helix spindle 锅杆hose clip 水喉箍bubbler 隔气运水jiggle 斜顶jiggle witness line 斜顶片位置center distance (CRS) 山打距离(中心线距离)clamp 码仔contour 外形leader pin 导针location ring(flange) 法兰counterbore 拔头,介子托mock-up;prototype 手办die cast 合金压铸national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,顶套epoxy 胶样pin point gate 细水口pressure plug 喉塞pressure spring 压力弹簧parting line flash 披锋burned 烧黑underfilled 缺料insert mismatch 镶件夹口ejector pins not flush 顶针有高低ejector pins skid 顶针滑动insert flash 镶件披锋pressure transducer 压力探测头hydraulic schematic 油积筒油路接驳图jiffy connector recessed 安装喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关stop block 限位块safety strap 安全带drool bushing 防漏胶套筒insert mismatch 镶件夹口EDM visible 明显火花纹lifter scrapes 斜顶拖花short shots 走水不齐wall stock 料位厚薄knit lines 走水纹stress marks 夹水纹uneven fill pattern 走水不平行drag marks 拖花sprue pretrusion 唧嘴突出高度sprue orifice and radil size 唧嘴R尺寸sprue bushing-keyed 唧嘴有管钉English Chineseprogram name 产口名称part name 零件名称tool name 模具名称tool source 模具来源tool steel 模具钢材resin 塑料program number 产品编号part number 零件编号tool number 模具编号customer 客户名称No of cavities 内模编号machine size 啤机吨数drum miller 鼓形铣床duplex horizontal miller 复式卧铣床face miller 端面铣床grinding miller 研磨机plain miller 平面铣床planer-type miller 刨式铣床rack miller 齿条铣床slab miller 大型平面铣床slot miller 键槽铣刀spline miller 花键铣刀thread miller 螺纹铣刀vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀plastic mould steel 塑料模钢cold work steel 冷作钢hot work steel 热作钢high speed steel 高速钢electric magnetic clutch 电磁离合器pad printer 移印机screen printer 丝印机hot stamper 烫印机solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片concave cutter 凹锣刀片side&face cutters,staggered teeth 正侧双用镶钻石钢锣刀end-mill 锣刀semi-rod 半圆刀split double end 双头刀single end 单头刀2-flute 两辨3-flute 三辨4-flute 四辨reamer 直拈centre drill 中心钻solid carbide drill 钻咀zinc ingot 锌锭aluminium ignot 铝锭tin ignot 锡锭heater cement 发热管的结合剂heater groove 发热管槽spacer rail 介子座cross pin 十字头销nozzle plate 射嘴板nozzle seat 热嘴addendum 齿冠dedendum 齿根air compressor 空气压缩机air exhauster 抽气机air intake 进气口air seal 空气隔离层。

模具零件中英文对照表

材料
S50C S50C S50C S50C STD STD STD STD STD STD 大同 STD STD STD STD STD STD STD STD STD STD STD STD S50C S50C S50C STD STD STD 六角铜富力 DME DME DME STD STD S50C 橡胶
ACC-XX WZ8087/M6 WZ8087/M8 WZ8087/M10 WZ8087/M12 WZ8087/M16 PLB-10 PLB-12 PLB-13 PLB-16 PLB-20 PL-BUSHINGS-13 PL-BUSHINGS-16 PSM-0001 PSM-0002 PSM-0003
L-5
STD EOC EOC EOC EOC EOC DAIDO DAIDO DAIDO DAIDO DAIDO D1 Z-82 Z-84 Z-26
Z-120 Z-121 Z-122 Z-123 Z-124
Z-55 Z-56 Z-57
Z-110
Z-27 Z-34
尺寸
<o>100X15 <o>100X15 <o>140X30 10X20X30 OD<o>30XID<o>16XL OD<o>35XID<o>19XL OD<o>40XID<o>22XL OD<o>50XID<o>27.5XL OD<o>60XID<o>33XL <o>8X<o>16X5 STP-165 19X32X100 19X19X70 16X25X70 16X30X90 20X50X130 OD<o>10.5XID<o>7.5X<o>1.5 OD<o>14.6XID<o>9.8X<o>2.4 OD<o>16.6XID<o>11.8X<o>2.4 OD<o>20.1XID<o>15.3X<o>2.4 OD<o>22.3XID<o>17.5X<o>2.4 OD<o>26.3XID<o>21.5X<o>2.4 OD<o>29.8XID<o>25X<o>2.4 44X72X144 44X72X72 30X50X80 BSPT 1/4" BSPT 3/8" BSPT 1/2" BSPT1/4" 18MMA/C MD-02PT/M JP-252-SV JP-352-SV N9-1/4"A 2X80X115 <o>3.3X6 4X16X52 2X16X52

模具名称中英文对照

模具名称中英文对照模具名称中英文对照模胚Mold Base顶板Top Clamp Plate脱料板Runner Stripper Plate热流板Spacer Plate母模板A Plate推板Stripper Plate公模板B Plate承板Support Plate方铁Spacer Block面针板Ejector Retainer Plate底针板Ejector plate底板Bottom Clamp Plate母模仁Cavity Insert公模仁Core Insert滑块Slide斜顶Lift镶针Core Pin镶件Insert互换镶件Change Insert滑块镶件Slide Insert铲鸡Wedge压条Plate斜导柱Slide Pin耐磨板Wear Plate导向块Guide Block斜顶导向块Lift Guide Block 滑块导轨Slide Guide滑块束块Slide Wedge斜顶底座Lift Base唧咀Sprue Bushing分流锥Sprue Spreader定位环Locating Ring胶口衬套Sprue Bushing电热衬套Hot Tip Bushing 电热管Heater电热圈Heater Band线接头Power控温耦合器Thermocouple顶针Ejector Pin扁顶针Rec. Ej. Pin方顶针Sqrt. Ej. Pin双节顶针Step Ej. Pin司筒Ejector Sleeve双节司筒Step Ej. Sleeve顶出块Ejector Block勾针Sprue Pin拉杆Puller Pillar拉料销Runner Lock Pin开闭器Slide Lock Set尼龙开闭器Parting Lock复位杆Return Pin支撑柱Support Pillar垃圾钉Stop Pin限制块Stop Block开模止板Stop Plate日期章Date Marked Pin压力胶Rubber Spring限位开关Limits Switch弹簧Spring轻小载荷弹簧Lightest Load Spring轻载荷弹簧Light Load Spring中载荷弹簧Medium Load Spring重载荷弹簧Heavy Load Spring极重载荷弹簧Super Load Spring圆线弹簧Wire Spring耐热弹簧Heatproof Spring弹簧柱Spring Rod波子弹簧Ball CatchO型圈O Ring隔水片Baffle Boards喉塞Pipe Plug水道塞子Coolant Plug水管Water Connection喷水管Cascade Water Junction挡水板Plug Baffles快速接头Jiffy-Tile Sockets水管无头螺丝Water Bass Pressure Plugs导柱Guide Pin直导套Straight Guide Bush有托导套Shoulder Guide Bush 顶针板导柱Ejector Guide Pin 顶针板导套Ejector Guide Bush限位螺丝Stop Bolt无头螺丝Screw Plug内六角螺丝S.H.C.S平头小螺丝F.H.C.S外六角螺丝Hexangdlar Bolt定位销Dowel Pin定位钢珠Ball Plung锁模块Lock Block0度定位块Straight Block Set 斜度定位块Taper Block Set圆形定位器Taper Pin Set轴Shaft轴承Bearing齿轮Gear凸轮Cam Whee气阀Valves气压缸Air Cylinder油压缸Hydraulic Cylinder油压马达Hydraulic Motors油封Oil Close轴用C环"C"Type Ring轴用E环"E"Type Ring 孔止环Stop Hold Ring。

模具零件名称中英文对照一览表

模具零件名称中英文对照一览表模具零件名称中英文对照一览表零件名称ENGLISH NAME 零件名称ENGLISH NAME 上固定板TOP CLAMPING PLATE 母模仁CAVITY母模板CAVITY PLATE 公模仁CORE公模板CORE PLATE 母模入子CAVITY INSERT模脚SUPPRORT BLOCK 母模心子CAVITY INSERT PIN上顶出板EJECTOR RET PLATE 母模替换入子CAVITY CHANGEABLE INSERT 下顶出板EJECTOR PLATE 公模入子CORE INSERT下固定板BOTTOM CLAMPING PLATE 公模心子CORE INSERT PIN隔热板THERMAL INSULATING PLATE 公模替换入子CORE CHANGEABLE INSERT 脱料板RUNNER STRIPPER PLATE 滑块入子SLIDE INSERT母模垫板CAVITY SUPPORT PLATE 滑块心子SLIDE INSERT PIN 公模垫板CORE SUPPORT PLATE 斜销入子ANLGE LIFTER INSERT 脱料板STRIPPER PLATE 斜销心子ANLGE LIFTER PIN 流道板RUNNER PLATE 流道开关RUNNER SHUT OFF定位环LOCATING RING T 形块T GIB注口衬套SPRUE BUSHNG U 形块U GIB导柱LEADER PIN 拉料销SPRUE PULLER PIN导套LEADER BUSHING 定位销DOWEL PIN顶板导柱GUIDE PIN 顶针EJECTOR PIN顶板导套GUIGE BUSHING 扁销RECTANGLE EJECTOR PIN 大拉杆LARGE PULLER PIN 套筒EJECTOR SLEEVE小拉杆SMALL PULLER PIN 顶出块EJECTOR BLOCK支撑柱SUPPORT PILLAR 斜销ANGLE LIFTER定位块INTERLOCKS 斜销座ANGLE LIFTER BASE定位柱LOCATION PILLAR 引导块GUIDE BLOCK开闭器(塑料型) FRICTIONAL PULLER 急回推杆LEVER弹簧SPRING 冷却棒THERMAL PIN运输板PL LOCK O 形环O RING零件名称ENGLISH NAME滑块SLIDE 隔水板STRAIGHT BUFFLE滑块座SLIDE BASE 水管接头JIFFY TYTE PLUG滑轨SLIDE RAIL 油封OIL SEAL后跟块HELL BLOCK 内六角螺钉SOCKET HEAD CAP SCREW耐磨板WEAR BLOCK 等高螺钉SOCKET HEAD STRIPPER BLOT 压板RAIL 吊模螺丝EYE BLOT限位块STOP BLOCK 吊环SAFETY HOIST RINGS定位夹SLIDE RETAINER 弹簧垫圈SPRING WASHER定位珠SLIDE RETAINER 加长型水管接头EXTENSION JIFFY TYTE PLUG急回机构POSITIVE EARLY EJECTOR RETURN急回推杆LEVER固定块MOUNT AND COVER PLATE 弹簧片ARM中文名称英文名称中文名称英文名称MOLD BASE内六角螺丝LOCATING RINGEJECTORSPRUE BUSHSPRINGHOT RUNNER无头螺丝SET SCREW CAVITY平头螺丝定位拨珠BALL CATCH前模镶件CAVITY INSERT EJECTOR SLEEVE 后模镶件CORE INSERT BLADE EJECTOR行位(滑块)有托顶针SHOULDER EJECTOR WEDGESPRUE PULLER ANGLE PINWEAR BLOCKPO LOCK JIGGLE导柱辅助器TAPERD SET EJECTOR BLOCK 散打螺丝STRIPPER BOLT STOP BLOCK等高螺丝(拉杆) AS SCREW EJECTION PLATE HYDRAULIC LEADER BLOCK 日期指示器DATE INDICATE WEDGE BLOCK 环保标记章SUPPORT PILLAR AIR JETRM MARKERLOCATING PINGUIDED EJECTION支撑杆(撑头)HYDRAULIC MOTOR塑胶模具常用零件中英文对照表BRONZESEAL RINGSPIRAL TUBESTOP PIN螺旋水套开关装置SWITCHSTAGE EJECTORCOPPER SPACE BLOCK WATER PIPE 液压马达INSERT PIN。

模具常用名称中英文对照表

23. 螺钉：Screw——缩写：Scw
24. 电极：Electrode——缩写：Elc
25. 限位：LIMIT——缩写：LT
26. 导向板：GUIDE PLATE——缩写GUP
27. 直顶块： STRAIGHT EJ BLOCK——缩写STB
28. 补强板： STIFFENING PLATE——缩写STP
5. 热流道板(热浇道板)：Hot runer——缩写：HR
6. 母模（定模）：Cavity——缩写：Cav
7. 导柱：Guide Pin——缩写：G.P.
8. 导套：Guide bush——缩写：G.B.
9. 复位杆：Release Pin——缩写：R.P.
10. 动模型芯（中间体）：Core——缩写：Cor
11. 模脚：Support parallels——缩写：Supa
12. 侧翼块：Side block——缩写：Sibk
13. 轮Leabharlann ：Plin——缩写：Plin 14. 模座（底座）：Die holder——缩写：Dho
15. 镶件：Insert——缩写：Ins
16. 滑块（行位块）：Slide——缩写：Sld
模具数模命名规则及常用名称中英文对照表（含缩写）
1. 射嘴：Nozzle——缩写：Noz
2. 定位圈：locating ring——缩写：locr
3. 浇口套：Sprue bush(Sprue busing) ——缩写：Sprb
4. 垫板(固定板)：Base Plate——缩写：BP
17. 斜顶块：Lifter——缩写：Lit
18. 推板(顶板)：Eject Plate——缩写：EP

模具零件中英名称对照表

H.P.T A.P STD S.L.T S.T.R E.J.B D.PN F.P P.PN I.B.H E.J.S E.R.D STD M.A.F H-13
E.L.E S-7 P.A.T S.W.P P.U.R C.S.T BRONZE
製表日期：89年11月13日
模具零件圖中英名稱對照表
序 DESC. FINISHED SIZE MATL. Code Name 序 DESC. FINISHED SIZE MATL. Code Name
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
模邊零度束仔壓板滑塊斜撐開銷斜梢螺絲引導塊擋塊推出塊固定梢定位梢拉出桿套筒挺射襯套頂出桿方形扁頂針無頭螺絲熱料道板隔熱墊塊熱澆道灌嘴熱澆道加熱管油壓缸 O型環電極壓塊另件螺桿拉環石膏耐摩板
S.C.A M.C.R
G.P(L.P) G.B.H(L.B.H)
RP ST SET E.G.P E.G.B SP S.T.B S.T.P C.P S.P.P
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
TOP PLT 上固定板 STRIP PLT 三板模脫料板 CAV. PLT 母模板 CORE PLT 公模板 CORE BACKING PLT 公模墊板 SPACER BLOCK(RAIL) 間隔板 EJ. RET. PLT 上頂出板 EJ. PLT 下頂出板 BOTTOM PLT 下固定板 CAVITY 母模仁 CORE or FOROE 公模仁 CORE INSERT 公仁入仔 CAV. INSERT 母仁入仔 GUIDE PIN(LEADER PIN) 導柱 (桿) GUIDE (LEADER) BUSHING 導銷襯套 LOC. RING 固定環 SPURE BUSH 進料灌嘴 RET PIN 回位銷 STOP PIN 停止銷 SET PIN 角位銷 EJECT GUIDE PIN 打板導桿 EJECT GUIDE BUSHIN 打板導桿襯套 SPRING 彈簧 SUPPORT 公模板支撐柱 STRIPPER BOLTS 制止螺絲 PULLER BOLTS 拖拉螺桿 INTERLOCK 模面固定束仔 CORE PIN 心型梢 SPRUE PULLER 注道拉出梢 SLIDE 滑塊

模具零件名称中英对照

53 sleeve-pinlok 54 55 56 57 58
31 32 33 34 35 36 37 38 39 40 41 42 43 44
前模模仁前模仁镶件前模仁镶针后模模仁部分后模模仁后模模仁镶件后模模仁镶针前模行位部分前模行位镶件前模行位镶针前模行位本体前模行位铲基前模行位斜导柱前模行位压块前模行位耐磨板后模行位部分后模行位镶件后模行位镶针后模行位本体后模行位铲基后模行位斜导柱后模行位压块后模行位耐磨板前模斜顶部分前模斜顶前模斜顶脚前模斜顶导向块后模斜顶部分后模斜顶
模具零件名称中英对照表
1 cav-acc 2 cav 3 cav-sub(insert) 4 cav-pin 5 core-acc 6 core 7 core-sub(insert) 8 core-pin 9 fix-sld-acc 10 fix-sld-sub 11 fix-sld-pin 12 fix-sld-body 13 fix-sld-cam 14 fix-sld-angpin 15 fix-sld-guide 16 fix-sld-wear 17 mov-sld-acc 18 mov-sld-sub 19 mov-sld-pin 20 mov-sld-body 21 mov-sld-cam 22 mov-sld-angpin 23 mov-sld-guide 24 mov-sld-wear 25 fix-lif-acc 26 fix-lif 27 fix-lif-leg 28 fix-lif-guide 29 mov-lif-acc 30 mov-lif
fix-mb
42 top-plt 43 str-plt 44 a-plt 45
mov-mb

模具中英文对照表

C09
顶管
SLEEVE
C10
阶梯顶管
DOUBLE SLEEVE
C11
拉料钩
SPRUE PULLER PIN
C12
斜导柱
ANGLEPIN
C13
限位柱
STOP PIN
C14
镶针
CORE PIN
C15
定位销
DOWELS PIN
C16
定位管
POWELS TUBULAR
C17
拉杆
PULL ROD
C18
浇口套
SPRUE BUSHING
HEATER BAND
C51
活动导套
LOOSE LEADER BUSHING
类别：D
特殊零件部份
零件编号
中文名称
英文名称
材质
热处理
备注
D01
射口垫管
EJECTOR TUBE
D02
压板
RETAINER PLATE
D03
垫块
BLOCK
D04
键
KET
D05
滑动轴承
SLIDE BEARING
D06
齿轮
GEAR
热处理
备注
C01
导柱
LEADER PIN
C02
导套
LEADER BUSHING
C03
推板导柱
GUIDE PIN
C04
推板导套
GUIDE BUSHING
C05
复位杆
RETURN PIN
C06
顶针
EJECTOR PIN
C07
扁顶针
RECTANGULAREJECTOR PIN
C08

模具零配件中英文对照.

常用模具零件中英文对照表2005-12-19 14:51:17 中国注塑网入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞:pipeplug锁模块：lockplate斜顶：anglefrompin斜顶杆：angleejectorrod尼龙拉勾：partinglocks活动臂：leverarm复位键、提前回杆：earlyreturnbar气阀：valves斜导边：anglepin术语：terms承压平面平衡：partingsurfacesupportbalance模排气：partinglineventing回针碰料位：returnpinandcavityinterference模总高超出啤机规格：moldbaseshuthight顶针碰运水：waterlineinterfereswithejectorpin料位出上/下模：partfromcavith(core)side模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate. 不准用镶件：Donotuse(core/cavity)insert用铍铜做镶件：useberylliumcopperinsert初步（正式）模图设计：preliinary(final)molddesign反呵：reversecore弹弓压缩量：springcompressedlength稳定性好：goodstability,stable强度不够：insufficientrigidity均匀冷却：evencooling扣模：sticking热膨胀：theroexpansion公差：tolorance铜公(电极）：copperelectrodecompre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具encapsulation molding 低压封装成型、射出成型用模具two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location 定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块electrical discharge machining (EDM) 电火花加工electrical insulating property 电绝缘性能electrochemical die-sinking machine 电解型腔加工机，电解型腔加工机床electrochemical machine (ECM) 电解加工机床，电化学加工机床electrochemical machining (ECM) 电解加工，电化学加工electro-discharge cutting 电火花加工，电火花切割electro-discharge cutting machine 电火花切割机electro-discharge machine tool 电火花加工机床Electro-discharge Machine 电火花加工机床electro-discharge machining 电火花加工electro-discharge machining process 电火花加工工艺，电火花加工工序epoxy resin 环氧树脂guide bushing 导套guide pillar 导柱，导杆，导柱guide pin 导向销，导杆guide pin cover 导柱盖guide plate 导料板，导板guide plate blanking die 导板式冲裁模，导板式落料模guide post 导柱，导柱guide stock plate 挡料板injection mold 注射模，注塑模injection molding 注射成型，注塑成型injection-molding machine 注塑机，注射机，注塑成形机injection plunger 注射柱塞in-line reciprocating screw 联机往复螺杆，串联往复螺杆，直线排列往复螺杆inner ram 内滑块inserting molding 嵌件成形integrated manufacturing 集成制造internal stress 内应力13.intermediate platen 中间板，隔板塑料成型模具的主要设计要素脱模距stripper distance脱模斜度draft投影面积projected area最大开距maximum daylight;open daylight闭合高度mould-shut height抽芯距core-pulling distance抽芯力core-pulling force脱模力ejector force开模力mould opening force模内压力internal mould pressure;cavity pressure成型压力moulding pressure背压环back-up ring 1 bar = 14.5psi高压接头bite type fitting液压马达hydraulic motor冷却水流量计waterflow regulator打磨器材abrasive material打磨砂轮grinding wheels切割砂轮cutting wheels码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具piping tools高压力软管high pressure hose风管,水软管air .water hose高压油表pressure gauge压力油喉hydraulic hoses光塑检测photoelastic testing吹塑模plastic blow mould注塑模plastic injection mould冲扎复合模blank & form compound die精密冲模precision blanking die熔料流动率MFR=melt flow rate熔料流动指数MET=melt flow index推板导柱guide pin for ejector plater座板clamping plate垫块space block(plate)推板ejector block(plate)afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件stage ejector 顶棍spacer rock(risers) 间隔板变形distortion弯曲warp拖花drag marks火花纹EDM marks困气venting烧黑burns表面缩水shrinkage料位过薄/砸穿thin wall stock走水不平行uneven fill pattern夹水纹/流纹witness line;mismatch;stress marks 走水纹knit lines走水不齐short shotsorifice 料口nozzle seat 热嘴垫圈nozzle plate 射嘴板cross pin 十字头销sled 射台seal ring 封密圈spacer rail 介子座heater groove 发热管槽heater cement 发热管的结合剂soak 浸泡seat 垫圈ream 铰大圆孔直径grind 磨床drill 钻床mill 铣床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚计hardness tester 硬度计angle gauge 角规marble table 云台石projector 投影仪height gauge 高度仪microscope 显微镜plug gauge 塞规leveller 水平器R gauge R 规Inter caliper 内分厘卡surface 平面仪item number 细目编码catalog number 材料分类编码undercut lip 倒扣口hot tip = hot drop = nozzle 热嘴blow-off strip 放气板blow-off nozzle 吹风口spiral hose 螺旋式的连接喉rust solvent 除锈剂shaft 曲轴ensile strength 拉伸力yield strength 屈服力spark erosion 电火花蚀刻etch(photo-etch) 电蚀harden 淬硬copper electrode 铜公corrosion resistance 耐腐蚀anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域reverse taper 倒啤把clamp plate 码板toggle clamp 快速夹vacuum furnace 真空炉cavity insert rounds 圆柱镶件cavity insert b0locks 方柱镶件tensile strength 抗张强度,抗拉强度Concept drawing 概念图Assembly drawing 装配图mismatch;witness line 夹纹shut-off(n.) 枕位venting valves 疏气阀venting plug 疏气塞valve casing 阀门罩twist drill 旋钻harden/nitride 碎硬anneal 退火temper 回火stess crack 应力断裂corrosion resistance 防腐,防锈tensile strength 物】抗张强度,抗拉强度split mould (分离)组合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,机械等)夹住东西的部分,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位clean-up 清理,清除,清扫Mold Dating Insert 模具日志镶件Hot Sprue Bushing 热浇口套semi-automatic 半自动quick disconnector 快速断开接头full shot 足量注射mismatch 夹痕;夹水纹ejector mark 顶痕screw boss 螺丝孔,螺丝基座sink mark 缩坑15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂drag mark 拖痕stress mark 应力痕reinforcement rib 加强筋slght stoning 轻度磨砂soliid line 实线dotted line 虚线internal diameter 内径external diameter 外径nickel-plated 电镀的handling hole;lifting hole 吊装孔parallel 平行块piston 活塞plunger 柱塞carrier 导轨rest 支架item number 项目编号catalog item 商品目录编码dimensional datum 尺寸基准heat treatment certification 淬硬证明文件back-up bushing 支撑导套jacking screw 起重螺丝,千斤顶tapped hole (带有螺旋角度的)螺丝孔diagonal corner 成对角的角落burn mark 烧痕hot runner mainfold (热流道板)分流板texuring 蚀纹clamping screw (注塑机)码模螺丝imperial 英制的metric 公制的puller bushing 水口套puller bar 水口铁drool bushing 防漏胶套筒safety switch 限位制water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件gate shut-offs 流道开关配件guided ejection 中托司parting line shutoff 前后模接触面waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱. BGV=Balanced Gate Value 平衡入水值spacer 垫块pocket 挖槽rough 粗加工finish 精加工plunge rate 进刀率retract rate 提刀速率splindle rate 主轴转速coolant 冷却液SPLIT RING 开口环(钥匙圈)侧向抽芯力side pulling-core forceconvert.transfer 转图guide pin 边针Tee slot cutter T 形SLOT CUTTER zigzag 双向切削constant overlap spiral 等距环切parallel spiral 环绕切削parallel spiral clean corners 环切并清角morph spiral 依外形环绕true spiral 螺旋切削one way 单向end mill 平铣刀spher mill 球刀bull mill 圆鼻刀face mill 面铣刀rad mill 圆角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔铣刀dove mill 鸠尾铣刀lot mill 棒状drill 钻孔reamer 纹刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心钻spot drill 点钻cntr bore 沉头孔刀c. sink 鱼眼孔钻loft surface 举升曲面coons surface 昆氏曲面ruled surface 直纹曲面revolved surface 旋转曲面swept surface 扫描曲面draft surface 牵引曲面grinding wheel 磨砂使用的轮子quench steel 将...淬火,使冷却stress relieving 应力消除molten 熔热的oxide film 氧化层guide pin and sleeve, locating ring ,导边,司筒,定位圈ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒, lifters, wear plate,horn pin,斜坊,磨损板,气顶针,O ring, water baffle, water pipe plug,O 形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板air cylinder,hydraulic cylinder,氯压缸,液压缸micro switch,oil nipple, spring,开关装置,油枪接头,弹弓sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cycle counter,date stamper，滑块固定板,生产日期铭牌,hot runner system ，热流道系统chemical composition 化学成份thermal conductiivity 导热性能thermal diffusivity 热扩散性能dimensonal stablity 尺寸稳定性能cooling effiency 冷却效率easiler ejection 易于脱模alloy insert 合金镶件(cooling) duct 输送管;导管maintenance cost 维护费用ultrasonic testing 超声波检测crack 断裂direct gate 直接浇口ring gate 环形浇口disk gate;disphragm gate 盘形浇口spoke gate;spider gate 轮辐浇口pin-point gate 点浇口edge gate 侧浇口submarine gate;tunnel gate 潜伏浇口fan gate 扇形浇口tab gate 护耳浇口runner plate 流道板(或冷或热)secondary nozzle 二级喷嘴torpedo;torpedo body assembly 鱼雷形组合体catridge heater 管式加热器heat pipe 热管valve gate 阀式浇口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活动镶件cavity splits;core splits(凹模拼块) (型芯拼块) 拼块side core 侧型芯thread plug;threaded core 螺纹型芯thread ring;threaded cavity 螺纹型环cutting wheel 切割砂轮grinding wheel 打磨砂轮abrasive material 打磨器材mould clamps;lifting clamp 砂模夹(注塑机使用)air (water) hose 风管,水轮管pressure gauge 高压油表hydraulic hose 压力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 冲扎复合模precisiion blanking die 精密冲模MFR=melt flow rate 熔料流动率MFT=melt flow index 熔料流动指数handling hole 拉铃孔stop plate 限位块linder bush 衬套spacer block(plate) 垫块,方铁back-up ring 背位环standoff 限位块American Safety Hoist Rings. 英制安全吊装环Mechanical Properties 机械性能Tensile Strength(MPa) 抗拉强度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 冲韧性Physical Properties 物理性能solidification shrinkage 凝固收缩率freezing range 凝固与熔范围thermal expansion 热膨胀系数specific heat 比热thermal conductivity 热导率electrical conductivity 电导率micro-structure 金相分析hot work tool steel 热作钢circular motion 环形运动variable 变数,参数graphics window 图形窗口45 degree entry and a zero degree exit. 进刀口45 度,退刀口0 度runner stripper plate 脱料板stripper plate 活动板spacer rock(risers) 间隔板stage ejector 顶棍sprue puller insert 扣针导套guide strip 行位后板afdek plate 挡尘板side gate 大水口pinpoint gate 细水口SHCS 杯头螺丝FHCS 平头螺丝set screw 无头螺丝ball catch 波子螺丝wedge 行位较杯gib 线条,(撑鸡的导轨)latch 拉杆clamp 码仔spring guide pin 弹弓导柱steel pad disc 橙仔方ejector cam insert 斜顶块(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把锁texture 花纹toggle-lok 回撞装置top clamping plate 顶码板unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙) set screw 喷头螺丝side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 弹弓座sprue puller 勾针/勾粒spring washer 弹簧塑圈stepped ejector pin 有托顶针strippers plate 推板/细水口板submarine gate 潜水口support pin 拉杆support plate 暗板surface finish 光洁度alignment strip 斜锁angle pin 斜针fan gate 扇形入水fillet 圆口ball catch 弹弓波子blade ejector 扁顶bottom clamping plate 底码板free length 自然长度bridge piece 水口铁helix spindle 锅杆hose clip 水喉箍bubbler 隔气运水jiggle 斜顶jiggle witness line 斜顶片位置center distance (CRS) 山打距离(中心线距离)clamp 码仔contour 外形leader pin 导针location ring(flange) 法兰counterbore 拔头,介子托mock-up;prototype 手办die cast 合金压铸national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,顶套epoxy 胶样pin point gate 细水口pressure plug 喉塞pressure spring 压力弹簧parting line flash 披锋burned 烧黑underfilled 缺料insert mismatch 镶件夹口ejector pins not flush 顶针有高低ejector pins skid 顶针滑动insert flash 镶件披锋pressure transducer 压力探测头hydraulic schematic 油积筒油路接驳图jiffy connector recessed 安装喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关stop block 限位块safety strap 安全带drool bushing 防漏胶套筒insert mismatch 镶件夹口EDM visible 明显火花纹lifter scrapes 斜顶拖花short shots 走水不齐wall stock 料位厚薄knit lines 走水纹stress marks 夹水纹uneven fill pattern 走水不平行drag marks 拖花sprue pretrusion 唧嘴突出高度sprue orifice and radil size 唧嘴R 尺寸sprue bushing-keyed 唧嘴有管钉English Chinese program name 产口名称part name 零件名称tool name 模具名称tool source 模具来源tool steel 模具钢材resin 塑料program number 产品编号part number 零件编号tool number 模具编号customer 客户名称No of cavities 内模编号machine size 啤机吨数drum miller 鼓形铣床duplex horizontal miller 复式卧铣床face miller 端面铣床grinding miller 研磨机plain miller 平面铣床planer-type miller 刨式铣床rack miller 齿条铣床slab miller 大型平面铣床slot miller 键槽铣刀spline miller 花键铣刀thread miller 螺纹铣刀vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀plastic mould steel 塑料模钢cold work steel 冷作钢hot work steel 热作钢high speed steel 高速钢electric magnetic clutch 电磁离合器pad printer 移印机screen printer 丝印机hot stamper 烫印机solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片concave cutter 凹锣刀片side&face cutters,staggered teeth end-mill 锣刀semi-rod 半圆刀split double end 双头刀single end 单头刀2-flute 两辨3-flute 三辨4-flute 四辨reamer 直拈centre drill 中心钻solid carbide drill 钻咀zinc ingot 锌锭aluminium ignot 铝锭tin ignot 锡锭heater cement 发热管的结合剂heater groove 发热管槽spacer rail 介子座cross pin 十字头销nozzle plate 射嘴板nozzle seat 热嘴addendum 齿冠dedendum 齿根air compressor 空气压缩机air exhauster 抽气机air intake 进气口air seal 空气隔离层Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush 直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣根据中文词汇查所关心的技术问题，解决实际工作中的难题例如，在汉语词汇中看到——高速冲孔废料上跳（かす上り、scrap jump ）词汇，到网上一搜，中图分类号TG382.6，文章编码：1671-3508-2008-10-07-517，“高速冲压中防止冲孔废料上跳的方法”一文会告诉你引起高速冲孔废料上跳的原因，不外乎有油膜粘连、真空吸附、刃口磨损、磁性未退四个主要方面，解决这些问题有三个方向的思路可以考虑，具体手段有“毛糙面”法、“斜刀口”法、“硅胶顶出”法、“凹模刃口倒退拔”法，等等。

模具中英文参照表

模具中英文参照表模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料# Cold Slag线切割Wire E.D.M轮廊Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap导柱位Leader Pin Location 耐落胶Teflon Paste 偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weldline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring 管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar下模水口铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch 斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin 顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring 管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹） Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形warping走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板 A'plateB板 B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary 丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt 盖板Cover Plate 齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag 线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High Volume Running Mold剖面图Cross Section模具结构Mold Construction模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension 模具完成日 completion date 雕刻Engrave托司 EJ.GUIDE PIN烧焊 Welding浇口 gate侧胶式 side gate潜伏式 sub gate热流道 hot runner阀浇式（大水口直接进胶）direct gate扇形式 fan gate手折式 break off gate点浇式 pin point gate单边打入子 runner insert gate搭接式浇口 tab gate隧道式澆口 tunnel gate牛角进胶 cashew gate/banana gate成型材料Injection material生产数（模具寿命）production volume二次加工second process投影面积projected area流动平衡 Equal flow coming out 锁模力 clamping force 成型机injection machine成型周期cycle time模具结构 mold construction模胚 Mold Base定位环 locating ring面板 top plate唧嘴 sprue流道 runner主流道 main runner分流道 side runnerA板 A plate导套 Bushing导柱 Leader Pin回针 Return Pin上模小镶件Cavity Sub-Insert 上模镶件Cavity Block行位Slide行位镶件Slide Insert压紧块（铲机）Jaw压条Gib后模 core小镶件Sub-Insert下模镶件Core Block下模小镶件Core Sub-Insert 料花 splay mark粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warping走水不平均Filling Uneven 走不齐Short Shot毛边 flash困气air trapping结合线 welding line熔接痕welding mark缩水 sink mark顶白 stress mark漏水Water Leakage刮花（擦伤）Galling火山口 crater液压油缸 hydraulic cylinder。

模具类零件名称中英文及标识一览表

模具类零件名称中英⽂及标识⼀览表类别中⽂名称英⽂名称 (DESCR)标识(SORT)类别中⽂名称英⽂名称 (DESCR)标识(SORT)模胚MOLDBASE M000上模运⽔零件CAV WATER PART AW**上码模板FIX CLAMP PLATE MA09下模运⽔零件COR WATER PART BW**顶针底板(加)EJ BOTTOM PLATE ADD MA-8喉塞PIPLE PLUG WG**顶针底板EJ BOTTOM PLATE MA08堵头COPPER PLUG WT**顶针⾯板(加)EJ UP PLATE ADD MA-7快速接头CONNECTORS WL**顶针⾯板EJ UP PLATE MA07喉通EXTENSION PLUGS WP**热流道模板HOT RUNNER PLATEMA06管接头NIPPLE WC**⽀承板SPACE PLATE MA05隔⽚BAFFLES WS**⾯板TOP CLAMP PLATE MA04螺旋柱HELIX PILLAR WH**⽔⼝推板PUSH PLATE MA03胶圈"O" RING WO**A板托板(加)SUP PLATE A ADD MA-2中间喉塞SEAL PLUGWB**A 板托板SUP PLATE A MA02集⽔器CATCHMENT UTENSIL WJ**A 板 A PLATE MA01三通接头 3 CHANNELS NIPPLE WD**推板PUSH PLATE MB01直通接头DIRECT NIPPLE WE**推板(加)PUSH PLATE ADD MB-1弯管接头FLEX TUBE WF**B 板 B PLATE MB02铜管COPPER TUBE WI**B 板托板SUP PLATE B MB03软管SOFT TUBEWK**B 板托板(加)SUP PLATE B ADD MB-3C 板SPACE PLATE MB04回针RETURN PIN GR**顶针⾯板EJ UP PLATE MB05弹簧柱SPRING　PILLAR GB**顶针⾯板(加)EJ UP PLATE ADD MB-5直⾝边钉GUIDE PINGP**顶针底板EJ BOTTOM PLATE MB06有托边钉SHOULD GUIDE PIN GS**顶针底板(加)EJ BOTTOM PLATE ADD MB-6中托边MIDDLE GUIDE GN**底板BOTTOM PLATE MB07定位司CENTER BUSH GC**底板(加)BOTTOM PLATE ADD MB-7中托司MIDDLE GUIDE BUSH GM**下码模板MOVE CLAMP PLATEMB09直司STRAIGHT BUSH GH**托司GUIDE BUSHGT**定位圈LOCATING RING LC**直⾝边锁STRAIGHT INTERLOCKS GK**整体唧嘴WHOLE SPRUE LW**⽅形互锁TEC TAP INTERLOCKS GA**延伸唧嘴EXTENDED SPRUE LE**圆形互锁ROU TAP INTERLOCKSGD**唧嘴SPRUE LS**唧嘴套SPRUE BUSH LB**垃圾钉STOP PIN XS**⽔⼝司RUNNER BUSH LR**管钉DOWEL PIN XP**热唧嘴HOT SPRUE LH**斜边ANGLE PIN XA**热嘴套HOT SPRUE BUSH LV**齿轮GEAR WHEEL XG**导热套DISTRIBUTOR TUBE LA**轴承BEARINGXB**发热管TUBE HEATER LN**马达HYDRAULIC MOTOR XM**热电偶PROBE HEATERLJ**键KEY XY**探针PROBE LM**垫圈WASHERXW**分流探针DISTRIBUTOR PROBE LD**开⼝介⼦RINGENT WASHER XX**定位件END CAP LF**⽀承柱SUPPORT PILLAR XU**发热圈NOZZLE HEATER LO**锁模块LOCK BLOCK XK**喷嘴NOZZLE CORE LG**⽓阀开关VALVE SWITH XV**间隔套NOZZLE SPACER LI**电源插坐POWER CONNECTOR XT**探针套PROBE BUSH LT**温控插坐THERMO CONNECTOR XC**调节环ADJUSTMENT RING LP**接线盒MOUNTING BOX XO**定位环REGISTER RING LQ**油缸HTDRAULIC CYLINDER XH**六⾓螺丝SIX HORN SCREWLL**K.O镶件K.O INSERTXI**模板类 (M )流道系统类（L ）模具类零件名称中英⽂及标识⼀览表命名：模号 +“_"+ 标识命名：模号 +“_"+标识命名：模号 +“_"+标识命名：模号+“_"+标识命名：模号+“_"+标识冷却（ W ）回针　边钉　边司（G ）功能件（X ）限位司STOP SLEEVE LU**⽇期镶件DATE INSERT XD**中⼼柱CEN SUP PADS LX**材料镶件MATERIAL INSERT XE**挡料环DROOL RING LY**感应开关LIMIT SWITCH XL**热流道板HOT MANIFOLD LK**计数器COUNTER VIEW XF**隔热板INSULATOR SHEETS LZ**⾏位定位器SLIDE　RETAINER XR**单个针阀热嘴SINGLE VALVE GATE LH-V 接线开关MOUNTING SWITCH XN**分流锥SPRUE SPREADER L1**⽓缸AIR CYLINDER XZ**针阀系统VALVE GATE SYS L2**传感器SENSORXQ**隔离环INSULATING RING L3**喷嘴头NOZZLE TIP L4**上内模CAVITY AI**密封帽SEALING CAP L5**下内模COREBI**限位螺丝STOP SCREWUR**上内模镶件CAVITY INSERT AD**下内模镶件CORE INSERT BD**杯头螺丝SHCS VS**⾏位滑块SLIDE SI**平头螺丝FHCS VF**⾏位块SLIDE BLOCK SD**⽆头螺丝SHSSVN**⾏位镶件SLIDE INSERT SS**波⼦螺丝BALL VB**斜顶杆LIFTER FP**六⾓螺丝Six Horn Screw VX**斜顶镶件LIFTER INSERT FD**⾏程螺丝SHSB VT**直顶STRAIGHT EJ EB**圆头螺丝IHCSVR**直顶块STRAIGHT EJ BLOCK EC**活动镶件FLOAT INSERTII**直⾝顶针EJECTOR PIN EP**直⾝顶针EJECTOR PIN E***⼀般铜公COPPERCU***有托顶针SHOULDER EJ PIN EH**枕位铜公PILLOW COPPERCU***-P扁顶针FLAT EJ PIN EF**直⾝司筒EJ SLEEVEES**左压条STRIP L SL**有托司筒SHOULDER EJ SLEEVE EE**右压条STRIP R SR**司筒针EJ SLEEVE PIN ED**斜鸡WEDGE SB**镶针CORE PIN PI**勾腿CAMSA**弹针SPRING PIN EI**⾏位油板SLIDE WEAR PLATE SP**勾针HITCH PINEJ**斜鸡油板WEDGE WEAR PLATE SW**⽓顶AIR POPPET VALVEEA**⾏位导轨块SLIDE GUIDE BLOCK SG**⾏位挡板SLIDE STOP PLATEST**标准预复位机构EARLY RETURN RW**复位杆RETRUN POLE RP**斜顶导滑板LIFTER GUIDE PLATE FL**摆臂FLIRT ARM RM**斜顶滑块LIFTER SLIDE BLOCK FH**固定块FIX BLOCK RF**斜顶导轨块LIFTER GUIDE BLOCK FG**挡块LOCATE BLOCKRL**斜顶油板LIFTER WEAR PLATEFW**标准扣机LATCH LOCK KW**杯司BUSH UB**尼龙扣钉NYLON LATCH LOCK KN**⽔⼝镶件GATE INSERT UG**扣鸡滑块LOCK BARKH**轴SHAFTUS**扣鸡锁块LOCK CONTROL BLOCK KB**定位块LOCATE BLOCK UL**扣鸡定位块LOCK HOUSINGKC**板PLATEUP**垫板SUPPORT PLATE UE**蓝弹⼸FLAT SPRING NF**顶杆EJECTOR POLE UD**黄弹⼸FLAT SPRING NB**导滑块GUIDE BLOCK UC**圆形弹⼸CIRCLE SPRING NL**楔紧块WEDGE BLOCKUX**弹性胶ELASTOMER NP**碟形弹⼸DISK SPRINGND**弹⼸（N ）顶针/镶针（E /P ）扣鸡（K ）预复位机构（R ）命名：模号+“_"+标识命名：模号+“_"+标识命名：模号+“_"+标识命名：模号+“_"+标识命名：模号+“_"+标识命名：模号+“_"+铜公所打⼯件号+"-"+铜公标识号螺丝类（V )命名：模号+“_"+标识命名：模号+“_"+标识命名：模号+“_"+标识命名：模号+“_"+标识铜公⾏位（S ）斜顶（F）其它加⼯件（U ）成型件。

模具零配件中英文对照解读

常用模具零件中英文对照表2005-12-19 14:51:17 中国注塑网入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞:pipeplug锁模块：lockplate斜顶：anglefrompin斜顶杆：angleejectorrod尼龙拉勾：partinglocks活动臂：leverarm复位键、提前回杆：earlyreturnbar气阀：valves斜导边：anglepin术语：terms承压平面平衡：partingsurfacesupportbalance模排气：partinglineventing回针碰料位：returnpinandcavityinterference模总高超出啤机规格：moldbaseshuthight顶针碰运水：waterlineinterfereswithejectorpin料位出上/下模：partfromcavith(core)side模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate. 不准用镶件：Donotuse(core/cavity)insert用铍铜做镶件：useberylliumcopperinsert初步（正式）模图设计：preliinary(final)molddesign反呵：reversecore弹弓压缩量：springcompressedlength稳定性好：goodstability,stable强度不够：insufficientrigidity均匀冷却：evencooling扣模：sticking热膨胀：theroexpansion公差：tolorance铜公(电极）：copperelectrodecompre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具encapsulation molding 低压封装成型、射出成型用模具two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location 定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块electrical discharge machining (EDM) 电火花加工electrical insulating property 电绝缘性能electrochemical die-sinking machine 电解型腔加工机，电解型腔加工机床electrochemical machine (ECM) 电解加工机床，电化学加工机床electrochemical machining (ECM) 电解加工，电化学加工electro-discharge cutting 电火花加工，电火花切割electro-discharge cutting machine 电火花切割机electro-discharge machine tool 电火花加工机床Electro-discharge Machine 电火花加工机床electro-discharge machining 电火花加工electro-discharge machining process 电火花加工工艺，电火花加工工序epoxy resin 环氧树脂guide bushing 导套guide pillar 导柱，导杆，导柱guide pin 导向销，导杆guide pin cover 导柱盖guide plate 导料板，导板guide plate blanking die 导板式冲裁模，导板式落料模guide post 导柱，导柱guide stock plate 挡料板injection mold 注射模，注塑模injection molding 注射成型，注塑成型injection-molding machine 注塑机，注射机，注塑成形机injection plunger 注射柱塞in-line reciprocating screw 联机往复螺杆，串联往复螺杆，直线排列往复螺杆inner ram 内滑块inserting molding 嵌件成形integrated manufacturing 集成制造internal stress 内应力13.intermediate platen 中间板，隔板塑料成型模具的主要设计要素脱模距stripper distance脱模斜度draft投影面积projected area最大开距maximum daylight;open daylight闭合高度mould-shut height抽芯距core-pulling distance抽芯力core-pulling force脱模力ejector force开模力mould opening force模内压力internal mould pressure;cavity pressure成型压力moulding pressure背压环back-up ring 1 bar = 14.5psi高压接头bite type fitting液压马达hydraulic motor冷却水流量计waterflow regulator打磨器材abrasive material打磨砂轮grinding wheels切割砂轮cutting wheels码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具piping tools高压力软管high pressure hose风管,水软管air .water hose高压油表pressure gauge压力油喉hydraulic hoses光塑检测photoelastic testing吹塑模plastic blow mould注塑模plastic injection mould冲扎复合模blank & form compound die精密冲模precision blanking die熔料流动率MFR=melt flow rate熔料流动指数MET=melt flow index推板导柱guide pin for ejector plater座板clamping plate垫块space block(plate)推板ejector block(plate)afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件stage ejector 顶棍spacer rock(risers) 间隔板变形distortion弯曲warp拖花drag marks火花纹EDM marks困气venting烧黑burns表面缩水shrinkage料位过薄/砸穿thin wall stock走水不平行uneven fill pattern夹水纹/流纹witness line;mismatch;stress marks 走水纹knit lines走水不齐short shotsorifice 料口nozzle seat 热嘴垫圈nozzle plate 射嘴板cross pin 十字头销sled 射台seal ring 封密圈spacer rail 介子座heater groove 发热管槽heater cement 发热管的结合剂soak 浸泡seat 垫圈ream 铰大圆孔直径grind 磨床drill 钻床mill 铣床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚计hardness tester 硬度计angle gauge 角规marble table 云台石projector 投影仪height gauge 高度仪microscope 显微镜plug gauge 塞规leveller 水平器R gauge R 规Inter caliper 内分厘卡surface 平面仪item number 细目编码catalog number 材料分类编码undercut lip 倒扣口hot tip = hot drop = nozzle 热嘴blow-off strip 放气板blow-off nozzle 吹风口spiral hose 螺旋式的连接喉rust solvent 除锈剂shaft 曲轴ensile strength 拉伸力yield strength 屈服力spark erosion 电火花蚀刻etch(photo-etch) 电蚀harden 淬硬copper electrode 铜公corrosion resistance 耐腐蚀anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域reverse taper 倒啤把clamp plate 码板toggle clamp 快速夹vacuum furnace 真空炉cavity insert rounds 圆柱镶件cavity insert b0locks 方柱镶件tensile strength 抗张强度,抗拉强度Concept drawing 概念图Assembly drawing 装配图mismatch;witness line 夹纹shut-off(n.) 枕位venting valves 疏气阀venting plug 疏气塞valve casing 阀门罩twist drill 旋钻harden/nitride 碎硬anneal 退火temper 回火stess crack 应力断裂corrosion resistance 防腐,防锈tensile strength 物】抗张强度,抗拉强度split mould (分离)组合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,机械等)夹住东西的部分,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位clean-up 清理,清除,清扫Mold Dating Insert 模具日志镶件Hot Sprue Bushing 热浇口套semi-automatic 半自动quick disconnector 快速断开接头full shot 足量注射mismatch 夹痕;夹水纹ejector mark 顶痕screw boss 螺丝孔,螺丝基座sink mark 缩坑15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂drag mark 拖痕stress mark 应力痕reinforcement rib 加强筋slght stoning 轻度磨砂soliid line 实线dotted line 虚线internal diameter 内径external diameter 外径nickel-plated 电镀的handling hole;lifting hole 吊装孔parallel 平行块piston 活塞plunger 柱塞carrier 导轨rest 支架item number 项目编号catalog item 商品目录编码dimensional datum 尺寸基准heat treatment certification 淬硬证明文件back-up bushing 支撑导套jacking screw 起重螺丝,千斤顶tapped hole (带有螺旋角度的)螺丝孔diagonal corner 成对角的角落burn mark 烧痕hot runner mainfold (热流道板)分流板texuring 蚀纹clamping screw (注塑机)码模螺丝imperial 英制的metric 公制的puller bushing 水口套puller bar 水口铁drool bushing 防漏胶套筒safety switch 限位制water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件gate shut-offs 流道开关配件guided ejection 中托司parting line shutoff 前后模接触面waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱. BGV=Balanced Gate Value 平衡入水值spacer 垫块pocket 挖槽rough 粗加工finish 精加工plunge rate 进刀率retract rate 提刀速率splindle rate 主轴转速coolant 冷却液SPLIT RING 开口环(钥匙圈)侧向抽芯力side pulling-core forceconvert.transfer 转图guide pin 边针Tee slot cutter T 形SLOT CUTTER zigzag 双向切削constant overlap spiral 等距环切parallel spiral 环绕切削parallel spiral clean corners 环切并清角morph spiral 依外形环绕true spiral 螺旋切削one way 单向end mill 平铣刀spher mill 球刀bull mill 圆鼻刀face mill 面铣刀rad mill 圆角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔铣刀dove mill 鸠尾铣刀lot mill 棒状drill 钻孔reamer 纹刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心钻spot drill 点钻cntr bore 沉头孔刀c. sink 鱼眼孔钻loft surface 举升曲面coons surface 昆氏曲面ruled surface 直纹曲面revolved surface 旋转曲面swept surface 扫描曲面draft surface 牵引曲面grinding wheel 磨砂使用的轮子quench steel 将...淬火,使冷却stress relieving 应力消除molten 熔热的oxide film 氧化层guide pin and sleeve, locating ring ,导边,司筒,定位圈ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒, lifters, wear plate,horn pin,斜坊,磨损板,气顶针,O ring, water baffle, water pipe plug,O 形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板air cylinder,hydraulic cylinder,氯压缸,液压缸micro switch,oil nipple, spring,开关装置,油枪接头,弹弓sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cycle counter,date stamper，滑块固定板,生产日期铭牌,hot runner system ，热流道系统chemical composition 化学成份thermal conductiivity 导热性能thermal diffusivity 热扩散性能dimensonal stablity 尺寸稳定性能cooling effiency 冷却效率easiler ejection 易于脱模alloy insert 合金镶件(cooling) duct 输送管;导管maintenance cost 维护费用ultrasonic testing 超声波检测crack 断裂direct gate 直接浇口ring gate 环形浇口disk gate;disphragm gate 盘形浇口spoke gate;spider gate 轮辐浇口pin-point gate 点浇口edge gate 侧浇口submarine gate;tunnel gate 潜伏浇口fan gate 扇形浇口tab gate 护耳浇口runner plate 流道板(或冷或热)secondary nozzle 二级喷嘴torpedo;torpedo body assembly 鱼雷形组合体catridge heater 管式加热器heat pipe 热管valve gate 阀式浇口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活动镶件cavity splits;core splits(凹模拼块) (型芯拼块) 拼块side core 侧型芯thread plug;threaded core 螺纹型芯thread ring;threaded cavity 螺纹型环cutting wheel 切割砂轮grinding wheel 打磨砂轮abrasive material 打磨器材mould clamps;lifting clamp 砂模夹(注塑机使用)air (water) hose 风管,水轮管pressure gauge 高压油表hydraulic hose 压力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 冲扎复合模precisiion blanking die 精密冲模MFR=melt flow rate 熔料流动率MFT=melt flow index 熔料流动指数handling hole 拉铃孔stop plate 限位块linder bush 衬套spacer block(plate) 垫块,方铁back-up ring 背位环standoff 限位块American Safety Hoist Rings. 英制安全吊装环Mechanical Properties 机械性能Tensile Strength(MPa) 抗拉强度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 冲韧性Physical Properties 物理性能solidification shrinkage 凝固收缩率freezing range 凝固与熔范围thermal expansion 热膨胀系数specific heat 比热thermal conductivity 热导率electrical conductivity 电导率micro-structure 金相分析hot work tool steel 热作钢circular motion 环形运动variable 变数,参数graphics window 图形窗口45 degree entry and a zero degree exit. 进刀口45 度,退刀口0 度runner stripper plate 脱料板stripper plate 活动板spacer rock(risers) 间隔板stage ejector 顶棍sprue puller insert 扣针导套guide strip 行位后板afdek plate 挡尘板side gate 大水口pinpoint gate 细水口SHCS 杯头螺丝FHCS 平头螺丝set screw 无头螺丝ball catch 波子螺丝wedge 行位较杯gib 线条,(撑鸡的导轨)latch 拉杆clamp 码仔spring guide pin 弹弓导柱steel pad disc 橙仔方ejector cam insert 斜顶块(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把锁texture 花纹toggle-lok 回撞装置top clamping plate 顶码板unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙) set screw 喷头螺丝side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 弹弓座sprue puller 勾针/勾粒spring washer 弹簧塑圈stepped ejector pin 有托顶针strippers plate 推板/细水口板submarine gate 潜水口support pin 拉杆support plate 暗板surface finish 光洁度alignment strip 斜锁angle pin 斜针fan gate 扇形入水fillet 圆口ball catch 弹弓波子blade ejector 扁顶bottom clamping plate 底码板free length 自然长度bridge piece 水口铁helix spindle 锅杆hose clip 水喉箍bubbler 隔气运水jiggle 斜顶jiggle witness line 斜顶片位置center distance (CRS) 山打距离(中心线距离)clamp 码仔contour 外形leader pin 导针location ring(flange) 法兰counterbore 拔头,介子托mock-up;prototype 手办die cast 合金压铸national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,顶套epoxy 胶样pin point gate 细水口pressure plug 喉塞pressure spring 压力弹簧parting line flash 披锋burned 烧黑underfilled 缺料insert mismatch 镶件夹口ejector pins not flush 顶针有高低ejector pins skid 顶针滑动insert flash 镶件披锋pressure transducer 压力探测头hydraulic schematic 油积筒油路接驳图jiffy connector recessed 安装喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关stop block 限位块safety strap 安全带drool bushing 防漏胶套筒insert mismatch 镶件夹口EDM visible 明显火花纹lifter scrapes 斜顶拖花short shots 走水不齐wall stock 料位厚薄knit lines 走水纹stress marks 夹水纹uneven fill pattern 走水不平行drag marks 拖花sprue pretrusion 唧嘴突出高度sprue orifice and radil size 唧嘴R 尺寸sprue bushing-keyed 唧嘴有管钉English Chinese program name 产口名称part name 零件名称tool name 模具名称tool source 模具来源tool steel 模具钢材resin 塑料program number 产品编号part number 零件编号tool number 模具编号customer 客户名称No of cavities 内模编号machine size 啤机吨数drum miller 鼓形铣床duplex horizontal miller 复式卧铣床face miller 端面铣床grinding miller 研磨机plain miller 平面铣床planer-type miller 刨式铣床rack miller 齿条铣床slab miller 大型平面铣床slot miller 键槽铣刀spline miller 花键铣刀thread miller 螺纹铣刀vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀plastic mould steel 塑料模钢cold work steel 冷作钢hot work steel 热作钢high speed steel 高速钢electric magnetic clutch 电磁离合器pad printer 移印机screen printer 丝印机hot stamper 烫印机solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片concave cutter 凹锣刀片side&face cutters,staggered teeth end-mill 锣刀semi-rod 半圆刀split double end 双头刀single end 单头刀2-flute 两辨3-flute 三辨4-flute 四辨reamer 直拈centre drill 中心钻solid carbide drill 钻咀zinc ingot 锌锭aluminium ignot 铝锭tin ignot 锡锭heater cement 发热管的结合剂heater groove 发热管槽spacer rail 介子座cross pin 十字头销nozzle plate 射嘴板nozzle seat 热嘴addendum 齿冠dedendum 齿根air compressor 空气压缩机air exhauster 抽气机air intake 进气口air seal 空气隔离层Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush 直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣根据中文词汇查所关心的技术问题，解决实际工作中的难题例如，在汉语词汇中看到——高速冲孔废料上跳（かす上り、scrap jump ）词汇，到网上一搜，中图分类号TG382.6，文章编码：1671-3508-2008-10-07-517，“高速冲压中防止冲孔废料上跳的方法”一文会告诉你引起高速冲孔废料上跳的原因，不外乎有油膜粘连、真空吸附、刃口磨损、磁性未退四个主要方面，解决这些问题有三个方向的思路可以考虑，具体手段有“毛糙面”法、“斜刀口”法、“硅胶顶出”法、“凹模刃口倒退拔”法，等等。

模具中英文对照表

热流道板hot manifold
发热管cartridge heater
探针thermocouples
插头connector plug
插座 connector socket
密封/封料 seal
三、运水water line
喉塞line pug
喉管tube
塑胶管plastic tube
托板support plate
螺丝 screw
管钉dowel pin
开模槽ply bar score
内模管位core/cavity inter-lock
顶针ejector pin
司筒ejector sleeve
司筒针ejector pin
推板stripper plate
缩呵movable core
模具常用名词中英文对照 (2010-10-25 17:01:11)转载▼
标签：文化分类：模具
一、水口gate
进水位gate location
水口形式gate type
大水口edge gate
细水口 pin-point gate
水口大小gate size
转水口switching gate
弹弓柱spring rod
弹弓die spring
镶pin
销子dowel pin
波子弹弓ball catch
喉塞pipe plug
锁模块lock plate
斜顶angle from pin
斜顶杆angle ejector rod
尼龙拉勾parting locks
复位键、提前回杆early return bar

模具术语中英文对照表

模具术语中英文对照表模具是制造行业中重要的零部件之一，不同的国家或地区对于模具的称呼和术语有着不同的表述。

下面是模具术语的中英文对照表，供大家参考。

一、模具结构及零部件1.凸模：punch/upper die2.凹模：die/lower die3.合页模：hinge die4.活动凸模：movable punch5.固定凸模：fixed punch6.活动凹模：movable die7.固定凹模：fixed die8.下座：bottom plate/bottom clamping plate9.定位销：locating pin10.定位套：locating sleeve/bushing11.导柱：guide pillar12.导套：guide bush13.顶杆：ejector rod/knockout rod14.顶针：ejector pin/knockout pin15.顶出板：ejector plate/knockout plate16.压簧：compression spring17.弹簧：tension spring18.滑块：slide block19.顶针板：ejector plate/knockout plate二、模具材料1.冷/热作模钢：cold/hot work die steel2.合金工具钢：alloy tool steel3.模具钢：mould steel4.不锈钢：stainless steel5.硬质合金：hard alloy/cemented carbide6.铝：aluminum7.铜：copper8.铜合金：copper alloy9.镁合金：magnesium alloy三、模具表面处理1.硬化：hardening2.淬火：quenching3.氮化：nitriding4.喷涂：spraying5.镀铬：chrome plating6.抛光：polishing7.喷砂：sandblasting四、模具制造工艺1.车削：turning2.铣削：milling3.磨削：grinding4.电火花加工：electric discharge machining (EDM)5.线割加工：wire-cut EDM6.钻孔：drilling7.铰孔：reaming8.螺纹加工：threading9.组装：assembly10.检验：inspection以上是模具术语的中英文对照表，本表可供参考，希望对有需要的读者有所帮助。

常用模具零件中英文对照表汇编

常用模具零件中英文对照表２0０5-1２-19 14:51：１7中国注塑网一、入水:gateﻭ进入位：gａte loｃａｔｉoｎ二、水口形式:gａte tｙｐｅ三、大水口:edge ｇatｅﻭ细水口：ｐin－point gａｔｅ四、水口大小：ｇａｔe sｉze五、转水口：switchinｇrunner/ｇate六、唧嘴口径:ｓpruｅdｉameter ﻭ二、流道：ｒｕnner七、热流道：hot runner,hｏt manｉｆoｌd八、热嘴冷流道: ｈｏｔsｐｒｕｅ/ｃolｄrｕnneｒ九、唧嘴直流：direct spｒｕｅｇate ﻭ圆形流道:ｒｏund(full/haｌｆrｕｎner十、流道电脑分析:molｄflｏw analｙsisﻭ流道平衡:ｒuｎnｅr baｌanｃe十一、热嘴：hot sprueﻭ热流道板：hoｔmaｎifolｄ十二、发热管：cartridgｅheateｒ十三、探针：ｔherｍocouples十四、插头: connｅｃtoｒplｕg十五、插座: ｃｏnnｅctｏｒsｏｃｋet ﻭ密封／封料：sｅａlﻭ三、运水：w aｔeｒｌiｎｅ十六、喉塞：ｌｉnｅｌpug ﻭ喉管：tube十七、塑胶管：plａstｉc tｕbe ﻭ快速接头:jiffy quick connecｔor plｕｇ／soc ker ﻭ四、模具零件：ｍoｌd coｍponｅnts十八、三板模:3-plate moldﻭ二板模:2-plate molｄ十九、边钉/导边：ｌeadｅr pｉn/guｉｄe pin二十、边司/导套：ｂusｈｉｎg/ｇuiｄｅbushiｎgﻭ中托司：sｈoｕlder gui ｄe bｕsｈiｎg ﻭ中托边:ｇuidｅｐin ﻭ顶针板:ｅｊectoｒrｅｔａinnｅｒpｌate ﻭ托板：supｐort plａｔeﻭ螺丝: screw二十一、管钉：dowｅｌpiｎ二十二、开模槽：pｌy bar sｃot二十三、内模管位：cｏre／ｃavity inｔer-lock ﻭ顶针：ejeｃtoｒｐin ﻭ司筒:ejeｃtｏr slｅｅvｅﻭ司筒针：ejecｔｏｒｐｉｎﻭ推板:strｉppｅr ｐl ａte ﻭ缩呵:ｍｏｖablｅｃore,return cｏｒｅcore pｕller ﻭ扣机（尼龙拉勾）:nylon lａtch loｃk二十四、斜顶:lｉfter ﻭ模胚（架）：moldｂａse二十五、上内模:caｖity inｓert ﻭ下内模:coreｉnsert ﻭ行位(滑块)：slide 二十六、镶件:ｉnｓeｒt二十七、压座/斜鸡:weｄge二十八、耐磨板/油板:wedge weａr plａtｅ二十九、压条:pｌate ﻭ撑头: support ｐｉllar三十、唧嘴: ｓprue ｂｕsｈingﻭ挡板：stop plate ﻭ定位圈:loｃａtinｇrinｇﻭ锁扣:laｔch ﻭ扣鸡：ｐaｒting lockｓet三十一、推杆:ｐushｂar ﻭ栓打螺丝:S.H.S．Ｂ三十二、顶板：erａcｕretun ﻭ活动臂:ｌever aｒｍ三十三、分流锥：spure speｒader三十四、水口司:ｂush三十五、垃圾钉：stop pin ﻭ隔片:ｂuffle三十六、弹弓柱：ｓpｒiｎgｒｏd三十七、弹弓:dｉe spring三十八、中托司:eｊectｏr guide bush ﻭ中托边：ｅjeｃtor gｕｉdeｐｉn ﻭ镶针:piｎﻭ销子：dowel ｐｉn三十九、波子弹弓:baｌl catch喉塞:ｐiｐｅplｕｇ锁模块:ｌocｋplate斜顶:anｇleｆrompin斜顶杆：aｎgｌｅeｊｅctoｒrod尼龙拉勾:partiｎglｏcks活动臂：leverarｍ复位键、提前回杆:earlyrｅｔuｒnbaｒ气阀:vａｌｖｅｓ斜导边:anglepin术语：ｔeｒmｓ承压平面平衡:parｔingｓurfaｃｅsuｐｐorｔｂalaｎce模排气:partinglｉneveｎting回针碰料位：retｕrnpiｎａｎdcａvityintｅrfeｒenｃｅ模总高超出啤机规格：ｍoｌdbａseｓｈuthighｔ顶针碰运水：waｔerlineiｎterｆereｓwithｅjectorpin料位出上/下模：paｒtｆromcａvｉth(corｅ）side模胚原身出料位：ｃaｖitydirectｃｕtonA-plａtｅ，coｒedｉrｅｃtcutｏnＢ-plat ｅ．不准用镶件:Donｏtuｓe(ｃｏre／cavity）inserｔ用铍铜做镶件:usebｅrylliumcopperinsert初步(正式）模图设计:prｅliinaｒy(ｆiｎａl)molddeｓｉｇn反呵：ｒeversｅｃｏre弹弓压缩量:sｐrｉｎｇcomprｅssｅdlengｔh稳定性好:gｏodｓtaｂｉｌｉty,ｓtable强度不够:ｉnsufficiｅntrigiｄitｙ。

模具零件标准名称中英文对照表

模具零件标准名称中英文对照表1 顶针E.P. 88 拉杆suppor pin2 有托顶针stepped E.P. 89 拉杆定位介子support pin spacer3 扁顶针rectangular E.P. 90 齿轮gear4 司筒E.P. sleeve 91 丝杆screw5 中心针center Pin 92 轴承bearing6 直身导边straight leader Pin 93 油缸oil cylinder7 直身杯司straight bushing 94 气缸air cylinder8 有托导边shoulder leader Pin 95 间隔圈spacer ring9 有托杯司shoulder bushing 96 垃圾钉stopper ring10 方定位块position block set 97 撑头support pillar11 定位锥taper pin set 98 行位开关组detection switch set12 尼龙塞parting lock 99 撑脚distance spacer13 中托司套ejector lead bushing 100 上模cavity14 中托导柱ejector leader pin 101 上模镶件cavity insert15 脱水口螺丝组puller bolt set 102 上模镶针inlay cavity pin16 限位螺丝stopper bolt 103 潜水镶套pin point gate buyshing17 限位钉positioning pin 104 流道衬板runner plate18 管位块slotter key 105 水口扣针runer lock pin19 弹簧spring 106 行位slider20 螺钉screw 107 行位导向键slider certer rail21 限位块distance spacer 108 行位镶件slider insert22 无头螺丝screw plug 109 斜边angular pin23 平头螺丝socket head cap screw 110 方斜边angular cam24 波子螺丝ball plunger 111 铲鸡locking block25 定位螺钉positioning screw plug 112 行位压板slider guide rail26 胶圈o ring 113 隔热板insulation sheet27 喉塞taper screw plug 114 压板(其他类) holding plate28 法兰locating ring 115 楔块spacer wedge29 唧嘴sprue bushing 116 销钉dowelpin30 截流塞cooling circuit plug 117 下模core31 上固定板top clamping plate 118 下模呵block core32 脱料板runner stripper plate 119 下模镶件core insert33 上模板cavity plate 120 下模镶针core pin34 推板stripper plate 121 拉板tension link35 下模板core plate 122 拉板介子tension link retainer36 支承板support plate 123 行位垫块slide plate37 间隔板spacer block 124 斜边压块holding plate for A.P.38 顶针板1 ejector retainer plate 125 斜顶loose core39 顶针板2 ejector plate 126 斜顶滑座slide unit for loose core40 顶针板3 ejector plate 127 冷胶套sprue lock bushing41 顶针板4 ejector plate 128 运水镶件insert for cooling42 下固定板botton clamping plate 129 等高螺钉stopper bolt43 回针return pin44 二板模2-plate mold 130 缩o哥return core45 三板模3-plate mold 131 扣鸡(尼龙拉勾) nylon latch lock46 中托司shoulder guide bushing 132 排气槽venting47 中托边guide pin 133 浇口gate48 顶针板ejector retainer plate 134 唧嘴口径sprue diameter49 底针板ejector support plate 135 浇注系统feed system50 托板support plate 136 浇口大小gate size51 管钉dowel pin 137 直接浇口direct gate52 导柱guide jpillars 138 环形浇口ring gate53 导套guide bushes 139 点浇口pin-point gate54 拉料杆sprue puller 140 侧浇口edge gate55 圆锥头拉料杆sprue puller, conical headed 141 盘形浇口disk gate56 分流道拉料杆runner puller 142 潜伏浇口submarine gate57 枯杆kicker pin 143 扇形浇口fam gate58 复位杆ejector plate return pin 144 护耳浇口tab gate59 导板guide plate 145 大小口edge gate60 滑板slicde plate 146 细水口pin-point gate61 耐磨板wear plate 147 转水口switching runner gate62 垫板backing plate 148 流道runner puller63 固定板retainer plate 149 主流道sprue64 支承板backing plate 150 分流道runner puller65 定位板locating plate 151 热流道hot runner66 推件固定板ejector retainer plate 152 梯形流道trapezoidal unner67 支承柱support pillar 153 圆形流道round runner68 支架ejector housing 154 热嘴hot sprue69 斜导柱angle pin 155 热流道板hot manifold70 行位slide 156 发热管cartridge heater71 斜鸡wedge 157 控针thermocouples72 弯销dog-leg cam 158 插头connector plug73 斜滑块angled-lift splits 159 插座connector socket74 定位圈locating ring 160 运水water line75 限位块stop block 161 喉管tube76 推块ejector pad 162 塑胶管plastic tube77 推件板stripper plate 163 快速接头jiffy quick connector socket78 定位销locating pin 164 收缩率shringkage79 垫块spacer 165 注射压力injection pressure80 型腔cavity 166 成形压力moulding pressure81 活动镶件movable insert 167 弯曲力bending force82 镶件insert 168 拉伸力drawing force83 型芯core 169 锁模力clamping force84 侧型芯side core 170 开模力mould opening force85 螺纹型芯threaded core 171 脱模力ejection force86 开模槽plybar slot 172 抽芯力core-pulling87 内模管位inter-lock 173 抽芯距core-pulling distance。