锐捷交换机命令大全

合集下载

锐捷基本命令大全

锐捷基本命令大全

>Enable 进入特权模式#Exit 返回上一级操作模式#End 返回到特权模式#write memory 或copy running-config startup-config 保存配置文件#del flash:config.text 删除配置文件(交换机及1700系列路由器)#erase startup-config 删除配置文件(2500系列路由器)#del flash:vlan.dat 删除Vlan配置信息(交换机)#Configure terminal 进入全局配置模式(config)# hostname switchA 配置设备名称为switchA(config)#banner motd & 配置每日提示信息&为终止符(config)#enable secret level 1 0 star 配置远程登陆密码为star(config)#enable secret level 15 0 star 配置特权密码为starLevel 1为普通用户级别,可选为1~15,15为最高权限级别;0表示密码不加密(config)#enable services web-server 开启交换机WEB管理功能Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等查看信息#show running-config 查看当前生效的配置信息#show interface fastethernet 0/3 查看F0/3端口信息#show interface serial 1/2 查看S1/2端口信息#show interface 查看所有端口信息#show ip interface brief 以简洁方式汇总查看所有端口信息#show ip interface 查看所有端口信息#show version 查看版本信息#show mac-address-table 查看交换机当前MAC地址表信息#show running-config 查看当前生效的配置信息#show vlan 查看所有VLAN信息#show vlan id 10 查看某一VLAN (如VLAN10)的信息#show interface fastethernet 0/1 switchport 查看某一端口模式(如F 0/1)#show aggregateport 1 summary 查看聚合端口AG1的信息#show spanning-tree 查看生成树配置信息#show spanning-tree interface fastethernet 0/1 查看该端口的生成树状态#show port-security 查看交换机的端口安全配置信息#show port-security address 查看地址安全绑定配置信息#show ip access-lists listname 查看名为listname的列表的配置信息#show access-lists端口的基本配置(config)#Interface fastethernet 0/3 进入F0/3的端口配置模式(config)#interface range fa 0/1-2,0/5,0/7-9 进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式(config-if)#speed 10 配置端口速率为10M,可选10,100,auto(config-if)#duplex full 配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应)(config-if)#no shutdown 开启该端口(config-if)#switchport access vlan 10 将该端口划入VLAN10中,用于VLAN(config-if)#switchport mode trunk 将该端口设为trunk模式,用于Tag vlan可选模式为access , trunk(config-if)#port-group 1 将该端口划入聚合端口AG1中,用于聚合端口聚合端口的创建(config)# interface aggregateport 1 创建聚合接口AG1(config-if)# switchport mode trunk 配置并保证AG1为trunk 模式(config)#int f0/23-24(config-if-range)#port-group 1 将端口(端口组)划入聚合端口AG1中生成树(config)#spanning-tree 开启生成树协议(config)#spanning-tree mode stp 指定生成树类型为stp可选模式stp , rstp , mstp(config)#spanning-tree priority 4096 设置交换机的优先级为4096 , 优先级值小为高。

锐捷基本命令大全

锐捷基本命令大全

>Enable‎进入特权模式‎#Exit 返回上一级操‎作模式#End 返回到特权模‎式#write memory‎或copy runnin‎g-config‎startu‎p-config‎保存配置文件‎#del flash:config‎.text 删除配置文件‎(交换机及17‎00系列路由‎器)#erase startu‎p-config‎删除配置文件‎(2500系列‎路由器)#del flash:vlan.dat 删除Vlan‎配置信息(交换机)#Config‎u re termin‎al进入全局配置‎模式(config‎)# hostna‎m e switch‎A配置设备名称‎为switc‎hA(config‎)#banner‎ motd & 配置每日提示‎信息&为终止符(config‎)#enable‎secret‎ l evel 1 0 star 配置远程登陆‎密码为sta‎r(config‎)#enable‎secret‎ l evel 15 0 star 配置特权密码‎为starLevel 1为普通用户‎级别,可选为1~15,15为最高权‎限级别;0表示密码不‎加密(config‎)#enable‎servic‎e s web-server‎开启交换机W‎EB管理功能‎Servic‎e s 可选以下:web-server‎(WEB管理)、telnet‎-server‎(远程登陆)等查看信息#show runnin‎g-config‎查看当前生效‎的配置信息#show interf‎a ce fastet‎h ernet‎ 0/3 查看F0/3端口信息#show interf‎a ce serial‎ 1/2 查看S1/2端口信息#show interf‎a ce 查看所有端口‎信息#show ip interf‎a ce brief 以简洁方式汇‎总查看所有端‎口信息#show ip interf‎a ce 查看所有端口‎信息#show versio‎n查看版本信息‎#show mac-addres‎s-table 查看交换机当‎前MA C地址‎表信息#show runnin‎g-config‎查看当前生效‎的配置信息#show vlan 查看所有VL‎A N信息#show vlan id 10 查看某一VL‎A N (如VLAN1‎0)的信息#show interf‎a ce fastet‎h ernet‎ 0/1 switch‎p ort 查看某一端口‎模式(如F 0/1)#show aggreg‎a tepor‎t 1 summar‎y查看聚合端口‎A G1的信息‎#show spanni‎n g-tree 查看生成树配‎置信息#show spanni‎n g-tree interf‎a ce fastet‎h ernet‎ 0/1 查看该端口的‎生成树状态#show port-securi‎t y 查看交换机的‎端口安全配置‎信息#show port-securi‎t y addres‎s查看地址安全‎绑定配置信息‎#show ip access‎-li sts listna‎me 查看名为li‎s tname‎的列表的配置‎信息#show access‎-l ists端口的基本配‎置(config‎)#Interf‎a ce fastet‎h ernet‎ 0/3 进入F0/3的端口配置‎模式(config‎)#interf‎a ce range fa 0/1-2,0/5,0/7-9 进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置‎模式(config‎-i f)#speed 10 配置端口速率‎为10M,可选10,100,auto(config‎-i f)#duplex‎full 配置端口为全‎双工模式,可选full‎(全双工),half(半双式),auto(自适应)(config‎-i f)#no shutdo‎wn开启该端口(config‎-i f)#switch‎p ort access‎vlan 10 将该端口划入‎V LAN10‎中,用于VLAN‎(config‎-i f)#switch‎p ort mode trunk 将该端口设为‎t runk模‎式,用于Tag vlan可选模式为a‎c cess , trunk(config‎-i f)#port-group 1 将该端口划入‎聚合端口AG‎1中,用于聚合端口‎聚合端口的创‎建(config‎)# interf‎a ce aggreg‎a tepor‎t 1 创建聚合接口‎A G1(config‎-i f)# switch‎p ort mode trunk 配置并保证A‎G1为trunk 模式(config‎)#int f0/23-24(config‎-i f-range)#port-group 1 将端口(端口组)划入聚合端口‎A G1中生成树(config‎)#spanni‎n g-tree 开启生成树协‎议(config‎)#spanni‎n g-tree mode stp 指定生成树类‎型为stp可选模式st‎p , rstp , mstp(config‎)#spanni‎n g-tree priori‎t y 4096 设置交换机的‎优先级为40‎96 , 优先级值小为‎高。

(完整版)锐捷交换机命令大全

(完整版)锐捷交换机命令大全

【第一部分】交换机支持的命令:1.交换机基本状态:switch: ;ROM状态,路由器是rommon>hostname> ;用户模式hostname# ;特权模式hostname(config)# ;全局配置模式hostname(config-if)# ;接口状态2.交换机口令设置:switch>enable ;进入特权模式switch#config terminal ;进入全局配置模式switch(config)#hostname;设置交换机的主机名switch(config)#enable secret xxx ;设置特权加密口令switch(config)#enable password xxa ;设置特权非密口令switch(config)#line console 0 ;进入控制台口switch(config-line)#line vty 0 4 ;进入虚拟终端switch(config-line)#login ;允许登录switch(config-line)#password xx ;设置登录口令xxswitch#exit ;返回命令3.交换机VLAN设置:switch#vlan database ;进入VLAN设置switch(vlan)#vlan 2 ;建VLAN 2switch(vlan)#no vlan 2 ;删vlan 2switch(config)#int f0/1 ;进入端口1switch(config-if)#switchport access vlan 2 ;当前端口加入vlan 2 switch(config-if)#switchport mode trunk ;设置为干线switch(config-if)#switchport trunk allowed vlan 1,2 ;设置允许的vlan switch(config-if)#switchport trunk encap dot1q ;设置vlan 中继switch(config)#vtp domain;设置发vtp域名switch(config)#vtp password;设置发vtp密码switch(config)#vtp mode server ;设置发vtp模式switch(config)#vtp mode client ;设置发vtp模式4.交换机设置IP地址:switch(config)#interface vlan 1 ;进入vlan 1switch(config-if)#ip address;设置IP地址switch(config)#ip default-gateway;设置默认网关switch#dir flash: ;查看闪存5.交换机显示命令:switch#write ;保存配置信息switch#show vtp ;查看vtp配置信息switch#show run ;查看当前配置信息switch#show vlan ;查看vlan配置信息switch#show interface ;查看端口信息switch#show int f0/0 ;查看指定端口信息【第二部分】路由器支持的命令:1.路由器显示命令:router#show run ;显示配置信息router#show interface ;显示接口信息router#show ip route ;显示路由信息router#show cdp nei ;显示邻居信息router#reload ;重新起动2.路由器口令设置:router>enable ;进入特权模式router#config terminal ;进入全局配置模式router(config)#hostname;设置交换机的主机名router(config)#enable secret xxx ;设置特权加密口令router(config)#enable password xxb ;设置特权非密口令router(config)#line console 0 ;进入控制台口router(config-line)#line vty 0 4 ;进入虚拟终端router(config-line)#login ;要求口令验证router(config-line)#password xx ;设置登录口令xx router(config)#(Ctrl+z) ;返回特权模式router#exit ;返回命令3.路由器配置:router(config)#int s0/0 ;进入Serail接口router(config-if)#no shutdown ;激活当前接口router(config-if)#clock rate 64000 ;设置同步时钟router(config-if)#ip address;设置IP地址router(config-if)#ip address second ;设置第二个IProuter(config-if)#int f0/0.1 ;进入子接口router(config-subif.1)#ip address;设置子接口IProuter(config-subif.1)#encapsulation dot1q;绑定vlan中继协议router(config)#config-register 0x2142 ;跳过配置文件router(config)#config-register 0x2102 ;正常使用配置文件router#reload ;重新引导4.路由器文件操作:router#copy running-config startup-config ;保存配置router#copy running-config tftp ;保存配置到tftprouter#copy startup-config tftp ;开机配置存到tftprouter#copy tftp flash: ;下传文件到flashrouter#copy tftp startup-config;下载配置文件ROM状态:Ctrl+Break ;进入ROM监控状态rommon>confreg 0x2142 ;跳过配置文件rommon>confreg 0x2102 ;恢复配置文件rommon>reset;重新引导rommon>copy xmodem: flash: ;从console传输文件rommon>IP_ADDRESS=10.65.1.2 ;设置路由器IP rommon>IP_SUBNET_MASK=255.255.0.0 ;设置路由器掩码rommon>TFTP_SERVER=10.65.1.1 ;指定TFTP服务器IP rommon>TFTP_FILE=c2600.bin ;指定下载的文件rommon>tftpdnld ;从tftp下载rommon>dir flash: ;查看闪存内容rommon>boot ;引导IOS5.静态路由:ip route;命令格式router(config)#ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;静态路由举例router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默认路由举例6.动态路由:router(config)#ip routing ;启动路由转发router(config)#router rip ;启动RIP路由协议。

锐捷网络交换机的配置命令集

锐捷网络交换机的配置命令集

锐捷网络交换机的配置命令集交换机>Enable 进入特权模式#Exit 返回上一级操作模式#End 返回到特权模式#write memory 或copy running-config startup-config 保存配置文件#del flash:config.text 删除配置文件(交换机及1700系列路由器)#erase startup-config 删除配置文件(2500系列路由器)#del flash:vlan.dat 删除Vlan配置信息(交换机)#Configure terminal 进入全局配置模式(config)# hostname switchA配置设备名称为switchA(config)#banner motd & 配置每日提示信息&为终止符(config)#enable secret level 1 0 star 配置远程登陆密码为star(config)#enable secret level 15 0 star 配置特权密码为starLevel 1为普通用户级别,可选为1~15,15为最高权限级别;0表示密码不加密(config)#enable services web-server 开启交换机WEB管理功能Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等查看信息#show running-config 查看当前生效的配置信息#show interface fastethernet 0/3 查看F0/3端口信息#show interface serial 1/2 查看S1/2端口信息#show interface 查看所有端口信息#show ip interface brief 以简洁方式汇总查看所有端口信息#show ip interface 查看所有端口信息#show version 查看版本信息#show mac-address-table 查看交换机当前MAC地址表信息#show running-config 查看当前生效的配置信息#show vlan 查看所有VLAN信息#show vlan id 10 查看某一VLAN (如VLAN10)的信息#show interface fastethernet 0/1 switchport 查看某一端口模式(如F 0/1)#show aggregateport 1 summary 查看聚合端口AG1的信息#show spanning-tree 查看生成树配置信息#show spanning-tree interface fastethernet 0/1 查看该端口的生成树状态#show port-security 查看交换机的端口安全配置信息#show port-security address 查看地址安全绑定配置信息#show ip access-lists listname 查看名为listname的列表的配置信息#show access-lists端口的基本配置(config)#Interface fastethernet 0/3 进入F0/3的端口配置模式(config)#interface range fa 0/1-2,0/5,0/7-9 进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式(config-if)#speed 10 配置端口速率为10M,可选10,100,auto(config-if)#duplex full 配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应)(config-if)#no shutdown 开启该端口(config-if)#switchport access vlan 10 将该端口划入VLAN10中,用于VLAN(config-if)#switchport mode trunk 将该端口设为trunk模式,用于Tag vlan可选模式为access , trunk(config-if)#port-group 1 将该端口划入聚合端口AG1中,用于聚合端口聚合端口的创建(config)# interface aggregateport 1 创建聚合接口AG1(config-if)# switchport mode trunk 配置并保证AG1为trunk 模式(config)#int f0/23-24(config-if-range)#port-group 1 将端口(端口组)划入聚合端口AG1中生成树(config)#spanning-tree 开启生成树协议(config)#spanning-tree mode stp 指定生成树类型为stp可选模式stp , rstp , mstp(config)#spanning-tree priority 4096 设置交换机的优先级为4096 , 优先级值小为高。

锐捷交换机配置命令

锐捷交换机配置命令

锐捷交换机配置命令交换机基本操作:1.进入特权模式Switch>enableSwitch#2.返回用户模式Switch#exitPress RETURN to get started!Switch>配置模式:全局配置模式[主机名(config)#]:配置交换机的整体参数子模式:1.线路配置模式[主机名(config-line)#]:配置交换机的线路参数2.接口配置模式[主机名(config-if)#]:配置交换机的接口参数1.进入、退出全局配置模式Switch#configure terminalSwitch(config)#exitSwitch#2.进入、退出线路配置模式Switch(config)#line console 0Switch(config-line)#exitSwitch(config)#3.进入、退出接口配置模式Switch(config)#interface fastEthernet 0/1Switch(config-if)#exitSwitch(config)#从子模式下直接返回特权模式Switch(config-if)#endSwitch#交换机操作帮助:1.支持命令简写(按TAB键将命令补充完整)2.在每种操作模式下直接输入“?”显示该模式下所有的命令3.命令空格“?”显示命令参数并对其解释说明4. “字符?”显示以该字符开头的命令5.命令历史缓存: (Ctrl+P)显示上一条命令,(Ctrl+N)显示下一条命令6.错误提示信息交换机显示命令:显示交换机硬件及软件的信息 Switch#show version显示当前运行的配置参数 Switch#show running-config显示保存的配置参数 Switch#show configure常用交换机EXEC命令:1.将当前运行的配置参数复制到flash:Switch#write memoryBuilding configuration...[OK]Switch#2.清空flash中的配置参数:Switch#delete flash:config.textSwitch#3.交换机重新启动:Switch#reloadSystem configuration has been modified. Save? [yes/no]:n Proceed with reload? [confirm]4.配置交换机主机名:Switch(config)#hostname S2126G-1S2126G-1(config)#5.配置交换机口令:1) 配置交换机的登陆密码S2126G(config)#enable secret level 1 0 star“0”表示输入的是明文形式的口令2) 配置交换机的特权密码S2126G(config)#enable secret level 15 0 star“0”表示输入的是明文形式的口令常用交换机配置命令:1、为交换机分配管理IP地址S2126G(config)#interface vlan 1S2126G(config-if)#ip address {IP address} {IP subnetmask}[secondary] 2、将接口启用S2126G(config-if)#no shutdown3、将接口关闭S2126G(config-if)#shutdown4、配置接口速率S2126G(config-if)#speed [10|100|auto]5、配置接口双工模式S2126G(config-if)#duplex [auto|full|half]显示接口状态:S2126G#show interface测定目的端的可达性:S2126G>ping {IP address}从TFTP服务器下载配置参数:S2126G#copy tftp startup-config管理交换机MAC地址表:1、查看MAC地址表S2126G#show mac-address-table2、配置MAC地址表记录的生存时间(缺省为300秒)S2126G(config)#mac-address-table aging-time <10-1000000>3、查看MAC地址表记录的生存时间S2126G#show mac-address-table aging-timeVLAN的配置:1.添加一个VLANS2126G(config)#vlan <1-4094>S2126G(config-vlan)#2.为VLAN命名S2126G(config-vlan)#name 名字将交换机端口分配到VLAN1.配置Port VLANSwitch(config-if)#switchport access vlan <1-4094>2.配置Tag VLANSwitch(config-if)#switchport mode trunk1)配置本地(native)VLANSwitch(config-if)#switchport trunk native vlan <1-4094>Native VLAN即PVID,默认情况下每个trunk口的native VLAN 是12)从主干链路中清除VLANSwitch(config-if)#switchport trunk allowed vlan except vlan-list 注:VLAN1不可被清除3)在主干链路中允许所有VLANSwitch(config-if)#switchport trunk allowed vlan all4)向主干链路中加入VLANSwitch(config-if)#switchport trunk allowed vlan add vlan-list VLAN的验证:1.显示全部的VLAN:Switch#show vlan2.显示单独的VLAN :Switch#show vlan id <1-4094>将VLAN信息保存到flash中:Switch#write memory从flash中清除VLAN信息:Switch#delete flash:vlan.datRSTP的配置:1.启用生成树:S2126G(config)#spanning-tree2.配置交换机优先级:S2126G(config)#spanning-tree priority <0-61440>“0”或“4096”的倍数(RSTP BPDU该值后12bit全0)3.配置交换机端口优先级:S2126G(config-if)#spanning-tree port-priority <0-240>“0”或“16”的倍数(RSTP BPDU该值后4bit全0)4、生成树hello时间的配置(由Root决定):S2126G(config)#spanning-tree hello-time <1-10>5、生成树的验证:Switch#show spanning-treeSwitch#show spanning-tree interface <接口名称> <接口编号>聚合端口的创建:Switch(config)# interface aggregateport 1 创建聚合接口AG1Switch(config-if)# switchport mode trunk 配置并保证AG1为 trunk 模式Switch(config)#int range f0/23-24Switch(config-if-range)#port-group 1 将端口(端口组)划入聚合端口AG1中生成树:Switch(config)#spanning-tree 开启生成树协议Switch(config)#spanning-tree mode stp 指定生成树类型为stp可选模式stp , rstp , mstpSwitch(config)#spanning-tree priority 4096 设置交换机的优先级为4096 , 优先级值小为高。

锐捷基本命令大全

锐捷基本命令大全

>Enable 进入特权模式之宇文皓月创作#Exit 返回上一级操纵模式#End 返回到特权模式#write memory 或copy running-config startup-config 保管配置文件#del flash:config.text 删除配置文件(交换机及1700系列路由器) #erase startup-config 删除配置文件(2500系列路由器)#del flash:vlan.dat 删除Vlan配置信息(交换机)#Configure terminal 进入全局配置模式(config)# hostname switchA 配置设备名称为switchA(config)#banner motd & 配置每日提示信息 &为终止符(config)#enable secret level 1 0 star 配置远程登陆密码为star(config)#enable secret level 15 0 star 配置特权密码为starLevel 1为普通用户级别,可选为1~15,15为最高权限级别;0暗示密码不加密(config)#enable services web-server 开启交换机WEB管理功能Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等检查信息#show running-config 检查当前生效的配置信息#show interface fastethernet 0/3 检查F0/3端口信息#show interface serial 1/2 检查S1/2端口信息#show interface 检查所有端口信息#show ip interface brief 以简洁方式汇总检查所有端口信息#show ip interface 检查所有端口信息#show version 检查版本信息#show mac-address-table 检查交换机当前MAC地址表信息#show running-config 检查当前生效的配置信息#show vlan 检查所有VLAN信息#show vlan id 10 检查某一VLAN (如VLAN10)的信息#show interface fastethernet 0/1 switchport 检查某一端口模式(如F 0/1)#show aggregateport 1 summary 检查聚合端口AG1的信息#show spanning-tree 检查生成树配置信息#show spanning-tree interface fastethernet 0/1 检查该端口的生成树状态#show port-security 检查交换机的端口平安配置信息#show port-security address 检查地址平安绑定配置信息#show ip access-lists listname 检查名为listname的列表的配置信息#show access-lists端口的基本配置(config)#Interface fastethernet 0/3 进入F0/3的端口配置模式(config)#interface range fa 0/1-2,0/5,0/7-9 进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式(config-if)#speed 10 配置端口速率为10M,可选10,100,auto(config-if)#duplex full 配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应)(config-if)#no shutdown 开启该端口(config-if)#switchport access vlan 10 将该端口划入VLAN10中,用于VLAN(config-if)#switchport mode trunk 将该端口设为trunk模式,用于Tag vlan可选模式为access , trunk(config-if)#port-group 1 将该端口划入聚合端口AG1中,用于聚合端口聚合端口的创建(config)# interface aggregateport 1 创建聚合接口AG1(config-if)# switchport mode trunk 配置并包管AG1为 trunk 模式(config)#int f0/23-24(config-if-range)#port-group 1 将端口(端口组)划入聚合端口AG1中生成树(config)#spanning-tree 开启生成树协议(config)#spanning-tree mode stp 指定生成树类型为stp可选模式stp , rstp , mstp(config)#spanning-tree priority 4096 设置交换机的优先级为4096 , 优先级值小为高。

锐捷交换机命令

锐捷交换机命令

锐捷交换机配置命令交换机基本操作1.进入特权模式Switch>enableSwitch#2.返回用户模式Switch#exitPress RETURN to get started!Switch>配置模式:全局配置模式[主机名(config)#]:配置交换机的整体参数子模式:1.线路配置模式[主机名(config-line)#]:配置交换机的线路参数2.接口配置模式[主机名(config-if)#]:配置交换机的接口参数1.进入全局配置模式下Switch#configure terminalSwitch(config)#exitSwitch#2.进入线路配置模式Switch(config)#line console 0Switch(config-line)#exitSwitch(config)#3.进入接口配置模式Switch(config)#interface fastEthernet 0/1Switch(config-if)#exitSwitch(config)#从子模式下直接返回特权模式Switch(config-if)#endSwitch#交换机操作帮助特点:1.支持命令简写(按TAB键将命令补充完整)2.在每种操作模式下直接输入“?”显示该模式下所有的命令3.命令空格“?”显示命令参数并对其解释说明4.字符“?”显示以该字符开头的命令5.命令历史缓存: (Ctrl+P)显示上一条命令,(Ctrl+N)显示下一条命令6.错误提示信息交换机显示命令:显示交换机硬件及软件的信息 Switch#show version显示当前运行的配置参数 Switch#show running-config显示保存的配置参数 Switch#show configure常用交换机EXEC命令将当前运行的配置参数复制到flash:Switch#write memoryBuilding configuration...[OK]Switch#清空flash中的配置参数:Switch#delete flash:Switch#交换机重新启动:Switch#reloadSystem configuration has been modified. Save? [yes/no]:nProceed with reload? [confirm]配置交换机主机名:Switch(config)#hostname S2126GS2126G(config)#配置交换机口令:1、配置交换机的登陆密码S2126G(config)#enable secret level 1 0 star“0”表示输入的是明文形式的口令2、配置交换机的特权密码S2126G(config)#enable secret level 15 0 Star“0”表示输入的是明文形式的口令常用交换机配置命令:1、为交换机分配管理IP地址S2126G(config)#interface vlan 1S2126G(config-if)#ip address {IP address} {IP subnetmask}[secondary] 2、将接口启用S2126G(config-if)#no shutdown3、将接口关闭S2126G(config-if)#shutdown4、配置接口速率S2126G(config-if)#speed [10|100|auto]5、配置接口双工模式S2126G(config-if)#duplex [auto|full|half显示接口状态:S2126G#show interfaces测定目的端的可达性:S2126G>ping {IP address}从TFTP服务器下载配置参数:S2126G#copy tftp startup-config管理交换机MAC地址表:1、查看MAC地址表S2126G#show mac-address-table2、配置MAC地址表记录的生存时间(缺省为300秒)S2126G(config)#mac-address-table aging-time <10-1000000>3、查看MAC地址表记录的生存时间S2126G#show mac-address-table aging-timeVLAN的配置:1.添加一个VLANS2126G(config)#vlan <1-4094>S2126G(config-vlan)#2.为VLAN命名(可选)S2126G(config-vlan)#name将交换机端口分配到VLAN1.配置Port VLANSwitch(config-if)#switchport access vlan <1-4094>2.配置Tag VLANSwitch(config-if)#switchport mode trunk1).配置本地(native)VLANSwitch(config-if)#switchport trunk native vlan <1-4094>2).从主干链路中清除VLANSwitch(config-if)#switchport trunk allowed vlan except注:VLAN1不可被清除VLAN的验证:1.显示全部的VLAN:Switch#show vlan2.显示单独的VLAN :Switch#show vlan id <1-4094>将VLAN信息保存到flash中:Switch#write memory从flash中清除VLAN信息:Switch#delete flash:RSTP的配置:1.启用生成树:S2126G(config)#spanning-tree2.配置交换机优先级:S2126G(config)#spanning-tree priority <0-61440>“0”或“4096”的倍数(RSTP BPDU该值后12bit全0)3.配置交换机端口优先级:S2126G(config-if)#spanning-tree port-priority <0-240> “0”或“16”的倍数(RSTP BPDU该值后4bit全0)4、生成树hello时间的配置(由Root决定):S2126G(config)#spanning-tree hello-time <1-10>5、生成树的验证:Switch#show spanning-treeSwitch#show spanning-tree interface <接口名称> <接口编号>以上用于锐捷交换机的。

锐捷交换机命令

锐捷交换机命令

锐捷交换机配置命令交换机基本操作1.进入特权模式Switch>enableSwitch#2.返回用户模式Switch#exitPress RETURN to get started!Switch>配置模式:全局配置模式[主机名(config)#]: 配置交换机的整体参数子模式:1. 线路配置模式[主机名(config-line)#]: 配置交换机的线路参数2. 接口配置模式[主机名(config-if)#]: 配置交换机的接口参数1. 进入全局配置模式下Switch#configure terminalSwitch(config)#exitSwitch#2. 进入线路配置模式Switch(config)#line console 0Switch(config-line)#exitSwitch(config)#3. 进入接口配置模式Switch(config)#interface fastEthernet 0/1Switch(config-if)#exitSwitch(config)#从子模式下直接返回特权模式Switch(config-if)#endSwitch#交换机操作帮助特点:1. 支持命令简写(按TAB 键将命令补充完整)2. 在每种操作模式下直接输入“?”显示该模式下所有的命令3. 命令空格“?”显示命令参数并对其解释说明4. 字符“?”显示以该字符开头的命令5. 命令历史缓存: (Ctrl+P) 显示上一条命令,(Ctrl+N) 显示下一条命令6. 错误提示信息交换机显示命令:显示交换机硬件及软件的信息Switch#show version显示当前运行的配置参数Switch#show running-config显示保存的配置参数Switch#show configure常用交换机EXEC 命令将当前运行的配置参数复制到flash:Switch#write memory Building configuration...[OK]Switch#清空flash 中的配置参数:Switch#delete flash:config.textSwitch#交换机重新启动:Switch#reloadSystem configuration has been modified. Save? [yes/no]:nProceed with reload? [confirm]配置交换机主机名:Switch(config)#hostname S2126GS2126G(config)#配置交换机口令:1、配置交换机的登陆密码S2126G(config)#enable secret level 1 0 star“0”表示输入的是明文形式的口令2、配置交换机的特权密码S2126G(config)#enable secret level 15 0 Star“0”表示输入的是明文形式的口令常用交换机配置命令:1、为交换机分配管理IP 地址S2126G(config)#interface vlan 1S2126G(config-if)#ip address {IP address} {IP subnetmask}[secondary] 2、将接口启用S2126G(config-if)#no shutdown3、将接口关闭S2126G(config-if)#shutdown4、配置接口速率S2126G(config-if)#speed [10|100|auto]5、配置接口双工模式S2126G(config-if)#duplex [auto|full|half显示接口状态:S2126G#show interfaces测定目的端的可达性:S2126G>ping {IP address}从TFTP 服务器下载配置参数:S2126G#copy tftp startup-config管理交换机MAC 地址表:1、查看MAC 地址表S2126G#show mac-address-table2、配置MAC 地址表记录的生存时间(缺省为300 秒)S2126G(config)#mac-address-table aging-time <10-1000000>3、查看MAC 地址表记录的生存时间S2126G#show mac-address-table aging-timeVLAN 的配置:1. 添加一个VLANS2126G(config)#vlan <1-4094>S2126G(config-vlan)#2. 为VLAN 命名(可选)S2126G(config-vlan)#name将交换机端口分配到VLAN1.配置Port VLANSwitch(config-if)#switchport access vlan <1-4094>2.配置Tag VLANSwitch(config-if)#switchport mode trunk1).配置本地(native)VLANSwitch(config-if)#switchport trunk native vlan <1-4094>2).从主干链路中清除VLANSwitch(config-if)#switchport trunk allowed vlan except注:VLAN1 不可被清除VLAN 的验证:1. 显示全部的VLAN :Switch#show vlan2. 显示单独的VLAN :Switch#show vlan id <1-4094>将VLAN 信息保存到flash 中:Switch#write memory从flash 中清除VLAN 信息:Switch#delete flash:vlan.datRSTP 的配置:1. 启用生成树:S2126G(config)#spanning-tree2. 配置交换机优先级:S2126G(config)#spanning-tree priority <0-61440>“0”或4“096 ”的倍数(RSTP BPDU 该值后12bit 全0)3. 配置交换机端口优先级:S2126G(config-if)#spanning-tree port-priority<0-240>“0”或1“6 ”的倍数(RSTP BPDU 该值后4bit 全0)4、生成树hello 时间的配置(由Root 决定):S2126G(config)#spanning-tree hello-time <1-10>5、生成树的验证:Switch#show spanning-treeSwitch#show spanning-tree interface < 接口名称> < 接口编号>以上用于锐捷交换机的。

锐捷三层交换机命令大全

锐捷三层交换机命令大全

交换机 >Enable 进入特权模式#Exit 返回上一级操作模式#End 返回到特权模式#write memory 或copy running-config startup-config 保存配置文件#del flash:config.text 删除配置文件(交换机及1700系列路由器)#erase startup-config 删除配置文件(2500系列路由器)#del flash:vlan.dat 删除Vlan配置信息(交换机)#Configure terminal 进入全局配置模式(config)# hostname switchA 配置设备名称为switchA(config)#banner motd & 配置每日提示信息 &为终止符(config)#enable secret level 1 0 star 配置远程登陆密码为star(config)#enable secret level 15 0 star 配置特权密码为starLevel 1为普通用户级别,可选为1~15,15为最高权限级别;0表示密码不加密(config)#enable services web-server 开启交换机WEB管理功能Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等查看信息#show running-config 查看当前生效的配置信息#show interface fastethernet 0/3 查看F0/3端口信息#show interface serial 1/2 查看S1/2端口信息#show interface 查看所有端口信息#show ip interface brief 以简洁方式汇总查看所有端口信息#show ip interface 查看所有端口信息#show version 查看版本信息#show mac-address-table 查看交换机当前MAC地址表信息#show running-config 查看当前生效的配置信息#show vlan 查看所有VLAN信息#show vlan id 10 查看某一VLAN (如VLAN10)的信息#show interface fastethernet 0/1 switchport 查看某一端口模式(如F 0/1)#show aggregateport 1 summary 查看聚合端口AG1的信息#show spanning-tree 查看生成树配置信息#show spanning-tree interface fastethernet 0/1 查看该端口的生成树状态#show port-security 查看交换机的端口安全配置信息#show port-security address 查看地址安全绑定配置信息#show ip access-lists listname 查看名为listname的列表的配置信息#show access-lists端口的基本配置(config)#Interface fastethernet 0/3 进入F0/3的端口配置模式(config)#interface range fa 0/1-2,0/5,0/7-9 进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式(config-if)#speed 10 配置端口速率为10M,可选10,100,auto(config-if)#duplex full 配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应)(config-if)#no shutdown 开启该端口(config-if)#switchport access vlan 10 将该端口划入VLAN10中,用于VLAN(config-if)#switchport mode trunk 将该端口设为trunk模式,用于Tag vlan可选模式为access , trunk(config-if)#port-group 1 将该端口划入聚合端口AG1中,用于聚合端口聚合端口的创建(config)# interface aggregateport 1 创建聚合接口AG1(config-if)# switchport mode trunk 配置并保证AG1为 trunk 模式(config)#int f0/23-24(config-if-range)#port-group 1 将端口(端口组)划入聚合端口AG1中生成树(config)#spanning-tree 开启生成树协议(config)#spanning-tree mode stp 指定生成树类型为stp可选模式stp , rstp , mstp(config)#spanning-tree priority 4096 设置交换机的优先级为4096 , 优先级值小为高。

锐捷交换机配置命令大全

锐捷交换机配置命令大全

锐捷交换机配置命令一、交换机基本配置交换机命名:在项目实施的时候,建议为处于不同位置的交换机命名,便于记忆,可提高后期管理效率。

switch(config)#hostname ruijie //ruijie为该交换机的名字交换机配置管理密码:配置密码可以提高交换机的安全性,另外,telnet登录交换机的时候,必须要求有telnet管理密码。

switch (config)#enable secret level 1 0 rg //配置telnet管理密码为rg,其中1表示telnet 密码,0表示密码不加密switch (config)#enable secret level 15 0 rg //配置特权模式下的管理密码rg,其中15表示为特权密码交换机配置管理IPswitch (config)#interface vlan 1 //假设管理VLAN为VLAN 1switch (config-if)#ip address 192.168.1.1 255.255.255.0 //给管理VLAN配置管理IP地址switch (config-if)#no shutdown //激活管理IP,养成习惯,无论配置什么设备,都使用一下这个命令交换机配置网关:switch(config)#ip default-gateway 192.168.1.254 //假设网关地址为192.168.1.254,此命令用户二层设备。

通过以上几个命令的配置,设备便可以实现远程管理,在项目实施时(尤其是设备位置比较分散)特别能提高效率。

1.1 接口介质类型配置锐捷为了降低SME客户的总体拥有成本,推出灵活选择的端口形式:电口和光口复用接口,方便用户根据网络环境选择对应的介质类型。

但光口和电口同时只能用其一,如图1,如使用了光口1F,则电口1不能使用。

接口介质类型的转换:Switch(config)#interface gigabitethernet 0/1Switch(config-if)#medium-type fiber //把接口工作模式改为光口Switch(config-if)#medium-type copper //把接口工作模式改为电口默认情况下,接口是工作在电口模式在项目实施中,如果光纤模块指示灯不亮,工作模式是否正确也是故障原因之一。

锐捷交换机的配置命令大全

锐捷交换机的配置命令大全

锐捷交换机的配置命令大全很多朋友多次提到锐捷交换机的配置,关于华为与H3C交换机的配置我们之前曾多次提到过,本期我们来了解锐捷交换机的配置。

一、基础配置命令1、准备命令>Enable 进入特权模式#Exit 返回上一级操作模式#End 返回到特权模式#write memory 或copy running-config startup-config 保存配置文件#del flash:config.text 删除配置文件(交换机及1700系列路由器)#erase startup-config 删除配置文件(2500系列路由器)#del flash:vlan.dat 删除Vlan配置信息(交换机)#Configure terminal 进入全局配置模式(config)# hostname switchA 配置设备名称为switchA(config)#banner motd & 配置每日提示信息 &为终止符(config)#enable secret level 1 0 star 配置远程登陆密码为star (config)#enable secret level 15 0 star 配置特权密码为starLevel 1为普通用户级别,可选为1~15,15为最高权限级别;0表示密码不加密(config)#enable services web-server 开启交换机WEB管理功能Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等2、查看信息#show running-config //查看当前生效的配置信息#show interface fastethernet 0/3 //查看F0/3端口信息#show interface serial 1/2 //查看S1/2端口信息#show interface //查看所有端口信息#show ip interface brief //以简洁方式汇总查看所有端口信息#show ip interface //查看所有端口信息#show version //查看版本信息#show mac-address-table //查看交换机当前MAC地址表信息#show running-config //查看当前生效的配置信息#show vlan //查看所有VLAN信息#show vlan id 10 //查看某一VLAN (如VLAN10)的信息#show interface fastethernet 0/1 //查看某一端口模式(如F 0/1)#show aggregateport 1 summary //查看聚合端口AG1的信息#show spanning-tree //查看生成树配置信息#show spanning-tree interface fastethernet 0/1 //查看该端口的生成树状态#show port-security //查看交换机的端口安全配置信息#show port-security address //查看地址安全绑定配置信息#show ip access-lists listname //查看名为listname的列表的配置信息3、端口的基本配置(config)#Interface fastethernet 0/3 //进入F0/3的端口配置模式(config)#interface range fa 0/1-2,0/5,0/7-9 //进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式(config-if)#speed 10 //配置端口速率为10M,可选10,100,auto(config-if)#duplex full //配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应)(config-if)#no shutdown //开启该端口(config-if)#switchport access vlan 10 //将该端口划入VLAN10中,用于VLAN(config-if)#switchport mode trunk //将该端口设为trunk模式,可选模式为access , trunk(config-if)#port-group 1 //将该端口划入聚合端口AG1中,用于聚合端口4、聚合端口的创建(config)# interface aggregateport 1 //创建聚合接口AG1(config-if)# switchport mode trunk //配置并保证AG1为trunk 模式(config)#int f0/23-24(config-if-range)#port-group 1 //将端口(端口组)划入聚合端口AG1中5、生成树配置多生成树协议:switch(config)#spanning-tree //开启生成树协议switch(config)#spanning-tree mst configuration //建立多生成树协议switch(config-mst)#name ruijie //命名为ruijieswitch(config-mst)#revision 1 //设定校订本为1switch(config-mst)#instance 0 vlan 10,20 //建立实例0switch(config-mst)#instance 1 vlan 30,40 //建立实例1switch(config)#spanning-tree mst 0 priority 4096 //设置优先级为4096switch(config)#spanning-tree mst 1 priority 8192 //设置优先级为8192switch(config)#interface vlan 10switch(config-if)#vrrp 1 ip 192.168.10.1 //此为vlan 10的IP地址switch(config)#interface vlan 20switch(config-if)#vrrp 1 ip 192.168.20.1 //此为vlan 20的IP地址switch(config)#interface vlan 30switch(config-if)#vrrp 2 ip 192.168.30.1 //此为vlan 30的IP地址(另一三层交换机)switch(config)#interface vlan 40switch(config-if)#vrrp 2 ip 192.168.40.1 //此为vlan 40的IP地址(另一三层交换机)6、VLAN的基本配置(config)#vlan 10 //创建VLAN10(config-vlan)#name vlanname // 命名VLAN为vlanname(config-if)#switchport access vlan 10 //将该端口划入VLAN10中某端口的接口配置模式下进行(config)#interface vlan 10 //进入VLAN 10的虚拟端口配置模式(config-if)# ip address 192.168.1.1 255.255.255.0 //为VLAN10的虚拟端口配置IP及掩码,二层交换机只能配置一个IP,此IP是作为管理IP使用,例如,使用T elnet的方式登录的IP地址(config-if)# no shutdown //启用该端口7、端口安全(config)# interface fastethernet 0/1 //进入一个端口(config-if)# switchport port-security //开启该端口的安全功能a、配置最大连接数限制(config-if)# switchport port-secruity maxmum 1 //配置端口的最大连接数为1,最大连接数为128(config-if)# switchport port-secruity violation shutdown//配置安全违例的处理方式为shutdown,可选为protect (当安全地址数满后,将未知名地址丢弃)、restrict(当违例时,发送一个Trap通知)、shutdown(当违例时将端口关闭,并发送Trap通知,可在全局模式下用errdisable recovery来恢复)b、IP和MAC地址绑定(config-if)#switchport port-security mac-address xxxx.xxxx.xxxx ip-address 172.16.1.1//接口配置模式下配置MAC地址xxxx.xxxx.xxxx和IP172.16.1.1进行绑定(MAC地址注意用小写)8、三层路由功能(针对三层交换机)(config)# ip routing //开启三层交换机的路由功能(config)# interface fastethernet 0/1(config-if)# no switchport //开启端口的三层路由功能(这样就可以为某一端口配置IP)(config-if)# ip address 192.168.1.1 255.255.255.0(config-if)# no shutdown9、三层交换机路由协议(config)# ip route 172.16.1.0 255.255.255.0 172.16.2.1 //配置静态路由注:172.16.1.0 255.255.255.0 为目标网络的网络号及子网掩码172.16.2.1 为下一跳的地址,也可用接口表示,如ip route 172.16.1.0 255.255.255.0 serial 1/2(172.16.2.0所接的端口)(config)# router rip //开启RIP协议进程(config-router)# network 172.16.1.0 //申明本设备的直连网段信息(config-router)# version 2 //开启RIP V2,可选为version 1(RIPV1)、version 2(RIPV2)(config-router)# no auto-summary //关闭路由信息的自动汇总功能(只有在RIPV2支持)(config)# router ospf //开启OSPF路由协议进程(针对1762,无需使用进程ID)(config)# router ospf 1 //开启OSPF路由协议进程(针对2501,需要加OSPF进程ID)(config-router)# network 192.168.1.0 0.0.0.255 area 0//申明直连网段信息,并分配区域号(area0为骨干区域)10、IP ACL:交换机采用命名的访问控制列表;分标准(stand)和扩展(extended)两种a、标准ACL(config)#ip access-list stand listname //定义命名标准列表,命名为listname,stand为标准列表(config-std-nacl)#deny 192.168.30.0 0.0.0.255 //拒绝来自192.168.30.0网段的IP流量通过注:deny:拒绝通过;可选:deny(拒绝通过)、permit(允许通过)192.168.30.0 0.0.0.255:源地址及源地址通配符;可使用any表示任何IP(config-std-nacl)#permit any(config-std-nacl)#end //返回b、扩展ACL(config)#ip access-list extended listname//定义命名扩展列表,命名为listname,extended为扩展(config-ext-nacl)#deny tcp 192.168.30.0 0.0.0.255 192.168.10.0 0.0.0.255 eq www //拒绝源地址为192.168.30.0网段的IP访问目的地址为192.168.10.0网段的WWW服务注:deny:拒绝通过,可选:deny(拒绝通过)、permit(允许通过)tcp: 协议名称,协议可以是udp, ip,eigrp, gre, icmp, igmp, igrp等等。

锐捷基本命令大全

锐捷基本命令大全

>Enable 进入特权模式#Exit 返回上一级操作模式#End 返回到特权模式#write memory 或copy running-config startup-config 保存配置文件#del flash:config.text 删除配置文件(交换机及1700系列路由器)#erase startup-config 删除配置文件(2500系列路由器)#del flash:vlan.dat 删除Vlan配置信息(交换机)#Configure terminal 进入全局配置模式(config)# hostname switchA 配置设备名称为switchA(config)#banner motd & 配置每日提示信息 &为终止符(config)#enable secret level 1 0 star 配置远程登陆密码为star(config)#enable secret level 15 0 star 配置特权密码为starLevel 1为普通用户级别,可选为1~15,15为最高权限级别;0表示密码不加密(config)#enable services web-server 开启交换机WEB管理功能Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等查看信息#show running-config 查看当前生效的配置信息#show interface fastethernet 0/3 查看F0/3端口信息#show interface serial 1/2 查看S1/2端口信息#show interface 查看所有端口信息#show ip interface brief 以简洁方式汇总查看所有端口信息#show ip interface 查看所有端口信息#show version 查看版本信息#show mac-address-table 查看交换机当前MAC地址表信息#show running-config 查看当前生效的配置信息#show vlan 查看所有VLAN信息#show vlan id 10 查看某一VLAN (如VLAN10)的信息#show interface fastethernet 0/1 switchport 查看某一端口模式(如F 0/1)#show aggregateport 1 summary 查看聚合端口AG1的信息#show spanning-tree 查看生成树配置信息#show spanning-tree interface fastethernet 0/1 查看该端口的生成树状态#show port-security 查看交换机的端口安全配置信息#show port-security address 查看地址安全绑定配置信息#show ip access-lists listname 查看名为listname的列表的配置信息#show access-lists端口的基本配置(config)#Interface fastethernet 0/3 进入F0/3的端口配置模式(config)#interface range fa 0/1-2,0/5,0/7-9 进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式(config-if)#speed 10 配置端口速率为10M,可选10,100,auto(config-if)#duplex full 配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应)(config-if)#no shutdown 开启该端口(config-if)#switchport access vlan 10 将该端口划入VLAN10中,用于VLAN(config-if)#switchport mode trunk 将该端口设为trunk模式,用于Tag vlan 可选模式为access , trunk(config-if)#port-group 1 将该端口划入聚合端口AG1中,用于聚合端口聚合端口的创建(config)# interface aggregateport 1 创建聚合接口AG1(config-if)# switchport mode trunk 配置并保证AG1为 trunk 模式(config)#int f0/23-24(config-if-range)#port-group 1 将端口(端口组)划入聚合端口AG1中生成树(config)#spanning-tree 开启生成树协议(config)#spanning-tree mode stp 指定生成树类型为stp可选模式stp , rstp , mstp(config)#spanning-tree priority 4096 设置交换机的优先级为4096 , 优先级值小为高。

锐捷命令大全

锐捷命令大全
锐捷设备常用网络命令整理
交换机配置模式
用户模式: switch>
交换机信息的查看,简单测试命令
特权模式: switch#
查看、管理交换机配置信息,测试、调试
配置模式: switch(config)#
配置交换机的整体参数
接口配置模式
switch(config-if)#
配置交换机的接口参数
Switch(config) #
vlan 100
Switch(config-vlan) #
name test这里TEST是名字,如果不定义名字也行,名字为自动设定
Switch(config-vlan) # end
把fastethernet 0/10作为access口加入了VLAN100
Switch (config)#interface vlan 1
!配置远程登录地址
Switch (config-if)#no shutdown
Switch (config-if)#ip address 192.168.1.1 255.255.255.0
Switch (config-if)#end
Ip address 10.1.2.1 255.255.255.0
No shutdown
三层接口(routed port)
Interface fastethernet 0/1
No switchport
(将交换机二层接口转换为三层接口)
Ip address 10.1.1.1 255.255.255.0
delete flash:vlan.dat
查看配置文件内容:
Switch#more config.text

锐捷基本命令大全

锐捷基本命令大全

>Enable 进入特权模式#Exit 返回上一级操作模式#End 返回到特权模式#write memory 或copy running-config startup-config 保存配置文件#del flash: 删除配置文件(交换机及1700系列路由器)#erase startup-config 删除配置文件(2500系列路由器)#del flash: 删除Vlan配置信息(交换机)#Configure terminal 进入全局配置模式(config)# hostname switchA 配置设备名称为switchA(config)#banner motd & 配置每日提示信息&为终止符(config)#enable secret level 1 0 star 配置远程登陆密码为star(config)#enable secret level 15 0 star 配置特权密码为starLevel 1为普通用户级别,可选为1~15,15为最高权限级别;0表示密码不加密(config)#enable services web-server 开启交换机WEB管理功能Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等查看信息#show running-config 查看当前生效的配置信息#show interface fastethernet 0/3 查看F0/3端口信息#show interface serial 1/2 查看S1/2端口信息#show interface 查看所有端口信息#show ip interface brief 以简洁方式汇总查看所有端口信息#show ip interface 查看所有端口信息#show version 查看版本信息#show mac-address-table 查看交换机当前MAC地址表信息#show running-config 查看当前生效的配置信息#show vlan 查看所有VLAN信息#show vlan id 10 查看某一VLAN (如VLAN10)的信息#show interface fastethernet 0/1 switchport 查看某一端口模式(如F 0/1)#show aggregateport 1 summary 查看聚合端口AG1的信息#show spanning-tree 查看生成树配置信息#show spanning-tree interface fastethernet 0/1 查看该端口的生成树状态#show port-security 查看交换机的端口安全配置信息#show port-security address 查看地址安全绑定配置信息#show ip access-lists listname 查看名为listname的列表的配置信息#show access-lists端口的基本配置(config)#Interface fastethernet 0/3 进入F0/3的端口配置模式(config)#interface range fa 0/1-2,0/5,0/7-9 进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式(config-if)#speed 10 配置端口速率为10M,可选10,100,auto(config-if)#duplex full 配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应)(config-if)#no shutdown 开启该端口(config-if)#switchport access vlan 10 将该端口划入VLAN10中,用于VLAN(config-if)#switchport mode trunk 将该端口设为trunk模式,用于Tag vlan可选模式为access , trunk(config-if)#port-group 1 将该端口划入聚合端口AG1中,用于聚合端口聚合端口的创建(config)# interface aggregateport 1 创建聚合接口AG1(config-if)# switchport mode trunk 配置并保证AG1为trunk 模式(config)#int f0/23-24(config-if-range)#port-group 1 将端口(端口组)划入聚合端口AG1中生成树(config)#spanning-tree 开启生成树协议(config)#spanning-tree mode stp 指定生成树类型为stp可选模式stp , rstp , mstp(config)#spanning-tree priority 4096 设置交换机的优先级为4096 , 优先级值小为高。

锐捷交换机命令大全

锐捷交换机命令大全

锐捷交换机命令大全【第一部分】交换机支持的命令:1.交换机基本状态:switch: ;ROM状态,路由器是rommon>hostname> ;用户模式hostname# ;特权模式hostname(config)# ;全局配置模式hostname(config-if)# ;接口状态2.交换机口令设置:switch>enable ;进入特权模式switch#config terminal ;进入全局配置模式switch(config)#hostname;设置交换机的主机名switch(config)#enable secret xxx ;设置特权加密口令switch(config)#enable password xxa ;设置特权非密口令switch(config)#line console 0 ;进入控制台口switch(config-line)#line vty 0 4 ;进入虚拟终端switch(config-line)#login ;允许登录switch(config-line)#password xx ;设置登录口令xxswitch#exit ;返回命令3.交换机VLAN设置:switch#vlan database ;进入VLAN设置switch(vlan)#vlan 2 ;建VLAN 2switch(vlan)#no vlan 2 ;删vlan 2switch(config)#int f0/1 ;进入端口1switch(config-if)#switchport access vlan 2 ;当前端口加入vlan 2 switch(config-if)#switchport mode trunk ;设置为干线switch(config-if)#switchport trunk allowed vlan 1,2 ;设置允许的vlan switch(config-if)#switchport trunk encap dot1q ;设置vlan 中继switch(config)#vtp domain;设置发vtp域名switch(config)#vtp password;设置发vtp密码switch(config)#vtp mode server ;设置发vtp模式switch(config)#vtp mode client ;设置发vtp模式4.交换机设置IP地址:switch(config)#interface vlan 1 ;进入vlan 1switch(config-if)#ip address;设置IP地址switch(config)#ip default-gateway;设置默认网关switch#dir flash: ;查看闪存5.交换机显示命令:switch#write ;保存配置信息switch#show vtp ;查看vtp配置信息switch#show run ;查看当前配置信息switch#show vlan ;查看vlan配置信息switch#show interface ;查看端口信息switch#show int f0/0 ;查看指定端口信息【第二部分】路由器支持的命令:1.路由器显示命令:router#show run ;显示配置信息router#show interface ;显示接口信息router#show ip route ;显示路由信息router#show cdp nei ;显示邻居信息router#reload ;重新起动2.路由器口令设置:router>enable ;进入特权模式router#config terminal ;进入全局配置模式router(config)#hostname;设置交换机的主机名router(config)#enable secret xxx ;设置特权加密口令router(config)#enable password xxb ;设置特权非密口令router(config)#line console 0 ;进入控制台口router(config-line)#line vty 0 4 ;进入虚拟终端router(config-line)#login ;要求口令验证router(config-line)#password xx ;设置登录口令xx router(config)#(Ctrl+z) ;返回特权模式router#exit ;返回命令3.路由器配置:router(config)#int s0/0 ;进入Serail接口router(config-if)#no shutdown ;激活当前接口router(config-if)#clock rate 64000 ;设置同步时钟router(config-if)#ip address;设置IP地址router(config-if)#ip address second ;设置第二个IProuter(config-if)#int f0/0.1 ;进入子接口router(config-subif.1)#ip address;设置子接口IProuter(config-subif.1)#encapsulation dot1q;绑定vlan中继协议router(config)#config-register 0x2142 ;跳过配置文件router(config)#config-register 0x2102 ;正常使用配置文件router#reload ;重新引导4.路由器文件操作:router#copy running-config startup-config ;保存配置router#copy running-config tftp ;保存配置到tftprouter#copy startup-config tftp ;开机配置存到tftprouter#copy tftp flash: ;下传文件到flashrouter#copy tftp startup-config;下载配置文件ROM状态:Ctrl+Break ;进入ROM监控状态rommon>confreg 0x2142 ;跳过配置文件rommon>confreg 0x2102 ;恢复配置文件rommon>reset;重新引导rommon>copy xmodem: flash: ;从console传输文件rommon>IP_ADDRESS=10.65.1.2 ;设置路由器IPrommon>IP_SUBNET_MASK=255.255.0.0 ;设置路由器掩码rommon>TFTP_SERVER=10.65.1.1 ;指定TFTP服务器IP rommon>TFTP_FILE=c2600.bin ;指定下载的文件rommon>tftpdnld ;从tftp下载rommon>dir flash: ;查看闪存内容rommon>boot ;引导IOS5.静态路由:ip route;命令格式router(config)#ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;静态路由举例router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默认路由举例6.动态路由:router(config)#ip routing ;启动路由转发router(config)#router rip ;启动RIP路由协议。

锐捷交换机命令大全

锐捷交换机命令大全

【第一部分】交换机支持的命令:1.交换机基本状态:s w i t c h:;R O M状态,路由器是r o m m o n> h o s t n a m e>;用户模式h o s t n a m e#;特权模式h o s t n a m e(c o n f i g)#;全局配置模式h o s t n a m e(c o n f i g-i f)#;接口状态2.交换机口令设置:s w i t c h>e n a b l e;进入特权模式s w i t c h#c o n f i g t e r m i n a l;进入全局配置模式s w i t c h(c o n f i g)#h o s t n a m e;设置交换机的主机名s w i t c h(c o n f i g)#e n a b l e s e c r e t x x x;设置特权加密口令s w i t c h(c o n f i g)#e n a b l e p a s s w o r d x x a;设置特权非密口令s w i t c h(c o n f i g)#l i n e c o n s o l e0;进入控制台口s w i t c h(c o n f i g-l i n e)#l i n e v t y04;进入虚拟终端s w i t c h(c o n f i g-l i n e)#l o g i n;允许登录s w i t c h(c o n f i g-l i n e)#p a s s w o r d x x;设置登录口令x x s w i t c h#e x i t;返回命令3.交换机V L A N设置:s w i t c h#v l a n d a t a b a s e;进入V L A N设置s w i t c h(v l a n)#v l a n2;建V L A N 2 s w i t c h(v l a n)#n o v l a n2;删v l a n 2 s w i t c h(c o n f i g)#i n t f0/1;进入端口 1 s w i t c h(c o n f i g-i f)#s w i t c h p o r t a c c e s s v l a n2;当前端口加入v l a n2 s w i t c h(c o n f i g-i f)#s w i t c h p o r t m o d e t r u n k;设置为干线s w i t c h(c o n f i g-i f)#s w i t c h p o r t t r u n k a l l o w e d v l a n1,2;设置允许的v l a n s w i t c h(c o n f i g-i f)#s w i t c h p o r t t r u n k e n c a p d o t1q;设置v l a n中继s w i t c h(c o n f i g)#v t p d o m a i n;设置发v t p域名s w i t c h(c o n f i g)#v t p p a s s w o r d;设置发v t p密码s w i t c h(c o n f i g)#v t p m o d e s e r v e r;设置发v t p模式s w i t c h(c o n f i g)#v t p m o d e c l i e n t;设置发v t p模式4.交换机设置I P地址:s w i t c h(c o n f i g)#i n t e r f a c e v l a n1;进入v l a n 1 s w i t c h(c o n f i g-i f)#i p a d d r e s s;设置I P地址s w i t c h(c o n f i g)#i p d e f a u l t-g a t e w a y;设置默认网关s w i t c h#d i r f l a s h:;查看闪存5.交换机显示命令:s w i t c h#w r i t e;保存配置信息s w i t c h#s h o w v t p;查看v t p配置信息s w i t c h#s h o w r u n;查看当前配置信息s w i t c h#s h o w v l a n;查看v l a n配置信息s w i t c h#s h o w i n t e r f a c e;查看端口信息s w i t c h#s h o w i n t f0/0;查看指定端口信息【第二部分】路由器支持的命令:1.路由器显示命令:router#showrun;显示配置信息router#showinterface;显示接口信息router#showiproute;显示路由信息router#showcdpnei;显示邻居信息router#reload;重新起动2.路由器口令设置:router>enable;进入特权模式router#configterminal;进入全局配置模式router(config)#hostname;设置交换机的主机名router(config)#enablesecretxxx;设置特权加密口令router(config)#enablepasswordxxb;设置特权非密口令router(config)#lineconsole0;进入控制台口router(config-line)#linevty04;进入虚拟终端router(config-line)#login;要求口令验证router(config-line)#passwordxx;设置登录口令xxrouter(config)#(Ctrl+z);返回特权模式router#exit;返回命令3.路由器配置:router(config)#ints0/0;进入Serail接口router(config-if)#noshutdown;激活当前接口router(config-if)#clockrate64000;设置同步时钟router(config-if)#ipaddress;设置IP地址router(config-if)#ipaddresssecond;设置第二个IProuter(config-if)#intf0/0.1;进入子接口router(config-subif.1)#ipaddress;设置子接口IProuter(config-subif.1)#encapsulationdot1q;绑定vlan中继协议router(config)#config-register0x2142;跳过配置文件router(config)#config-register0x2102;正常使用配置文件router#reload;重新引导4.路由器文件操作:router#copyrunning-configstartup-config;保存配置router#copyrunning-configtftp;保存配置到tftprouter#copystartup-configtftp;开机配置存到tftprouter#copytftpflash:;下传文件到flashrouter#copytftpstartup-config;下载配置文件ROM状态:Ctrl+Break;进入ROM监控状态rommon>confreg0x2142;跳过配置文件rommon>confreg0x2102;恢复配置文件rommon>reset;重新引导rommon>copyxmodem:flash:;从console传输文件;设置路由器IP;设置路由器掩码rommon>T;指定TFTP服务器IPrommon>TFTP_FILE=c2600.bin;指定下载的文件rommon>tftpdnld;从tftp下载rommon>dirflash:;查看闪存内容rommon>boot;引导IOS5.静态路由:iproute;命令格式;静态路由举例;默认路由举例6.动态路由:router(config)#iprouting;启动路由转发router(config)#routerrip;启动RIP路由协议。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

[第一部分]交换机支持的命令:1.交换机基本状态:switch: ;ROM状态,路由器是rommon>hostname> ;用户模式hostname# ;特权模式hostname<config># ;全局配置模式hostname<config-if># ;接口状态2.交换机口令设置:switch>enable ;进入特权模式switch#config terminal ;进入全局配置模式switch<config>#hostname;设置交换机的主机名switch<config>#enable secret xxx ;设置特权加密口令switch<config>#enable password xxa ;设置特权非密口令switch<config>#line console 0 ;进入控制台口switch<config-line>#line vty 0 4 ;进入虚拟终端switch<config-line>#login ;允许登录switch<config-line>#password xx ;设置登录口令xxswitch#exit ;返回命令3.交换机VLAN设置:switch#vlan database ;进入VLAN设置switch<vlan>#vlan 2 ;建VLAN 2switch<vlan>#no vlan 2 ;删vlan 2switch<config>#int f0/1 ;进入端口1switch<config-if>#switchport access vlan 2 ;当前端口加入vlan 2switch<config-if>#switchport mode trunk ;设置为干线switch<config-if>#switchport trunk allowed vlan 1,2 ;设置允许的vlan switch<config-if>#switchport trunk encap dot1q ;设置vlan 中继switch<config>#vtp domain;设置发vtp域名switch<config>#vtp password;设置发vtp密码switch<config>#vtp mode server ;设置发vtp模式switch<config>#vtp mode client ;设置发vtp模式4.交换机设置IP地址:switch<config>#interface vlan 1 ;进入vlan 1switch<config-if>#ip address;设置IP地址switch<config>#ip default-gateway;设置默认网关switch#dir flash: ;查看闪存5.交换机显示命令:switch#write ;保存配置信息switch#show vtp ;查看vtp配置信息switch#show run ;查看当前配置信息switch#show vlan ;查看vlan配置信息switch#show interface ;查看端口信息switch#show int f0/0 ;查看指定端口信息[第二部分]路由器支持的命令:1.路由器显示命令:router#show run ;显示配置信息router#show interface ;显示接口信息router#show ip route ;显示路由信息router#show cdp nei ;显示邻居信息router#reload ;重新起动2.路由器口令设置:router>enable ;进入特权模式router#config terminal ;进入全局配置模式router<config>#hostname;设置交换机的主机名router<config>#enable secret xxx ;设置特权加密口令router<config>#enable password xxb ;设置特权非密口令router<config>#line console 0 ;进入控制台口router<config-line>#line vty 0 4 ;进入虚拟终端router<config-line>#login ;要求口令验证router<config-line>#password xx ;设置登录口令xx router<config>#<Ctrl+z> ;返回特权模式router#exit ;返回命令3.路由器配置:router<config>#int s0/0 ;进入Serail接口router<config-if>#no shutdown ;激活当前接口router<config-if>#clock rate 64000 ;设置同步时钟router<config-if>#ip address;设置IP地址router<config-if>#ip addresssecond ;设置第二个IP router<config-if>#int f0/0.1 ;进入子接口router<config-subif.1>#ip address;设置子接口IProuter<config-subif.1>#encapsulation dot1q;绑定vlan中继协议router<config>#config-register 0x2142 ;跳过配置文件router<config>#config-register 0x2102 ;正常使用配置文件router#reload ;重新引导4.路由器文件操作:router#copy running-config startup-config ;保存配置router#copy running-config tftp ;保存配置到tftprouter#copy startup-config tftp ;开机配置存到tftprouter#copy tftp flash: ;下传文件到flashrouter#copy tftp startup-config;下载配置文件ROM状态:Ctrl+Break ;进入ROM监控状态rommon>confreg 0x2142 ;跳过配置文件rommon>confreg 0x2102 ;恢复配置文件rommon>reset;重新引导rommon>copy xmodem: flash: ;从console传输文件rommon>IP_ADDRESS=10.65.1.2 ;设置路由器IPrommon>IP_SUBNET_MASK=255.255.0.0 ;设置路由器掩码rommon>TFTP_SERVER=10.65.1.1 ;指定TFTP服务器IPrommon>TFTP_FILE=c2600.bin ;指定下载的文件rommon>tftpdnld ;从tftp下载rommon>dir flash: ;查看闪存内容rommon>boot ;引导IOS5.静态路由:ip route;命令格式router<config>#ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;静态路由举例router<config>#ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默认路由举例6.动态路由:router<config>#ip routing ;启动路由转发router<config>#router rip ;启动RIP路由协议.router<config-router>#network;设置发布路由router<config-router>#negihbor;点对点帧中继用.7.帧中继命令:router<config>#frame-relay switching ;使能帧中继交换router<config-s0>#encapsulation frame-relay ;使能帧中继router<config-s0>#fram-relay lmi-type cisco ;设置管理类型router<config-s0>#frame-relay intf-type DCE ;设置为DCE router<config-s0>#frame-relay dlci 16 ;router<config-s0>#frame-relay local-dlci 20 ;设置虚电路号router<config-s0>#frame-relay interface-dlci 16 ;router<config>#log-adjacency-changes ;记录邻接变化router<config>#int s0/0.1 point-to-point ;设置子接口点对点router#show frame pvc ;显示永久虚电路router#show frame map ;显示映射8.基本访问控制列表:router<config>#access-listpermit|denyrouter<config>#interface;default:deny anyrouter<config-if>#ip access-groupin|out ;defaultut例1:router<config>#access-list 4 permit 10.8.1.1router<config>#access-list 4 deny 10.8.1.0 0.0.0.255router<config>#access-list 4 permit 10.8.0.0 0.0.255.255 router<config>#access-list 4 deny 10.0.0.0 0.255.255.255 router<config>#access-list 4 permit anyrouter<config>#int f0/0router<config-if>#ip access-group 4 in9.扩展访问控制列表:access-listpermit|deny icmp[type]access-listpermit|deny tcp[port]例3:router<config>#access-list 101 deny icmp any 10.64.0.2 0.0.0.0 echorouter<config>#access-list 101 permit ip any anyrouter<config>#int s0/0router<config-if>#ip access-group 101 in例3:router<config>#access-list 102 deny tcp any 10.65.0.2 0.0.0.0 eq 80router<config>#access-list 102 permit ip any anyrouter<config>#interface s0/1router<config-if>#ip access-group 102 out10.删除访问控制例表:router<config>#no access-list 102router<config-if>#no ip access-group 101 in11.路由器的nat配置Router<config-if>#ip nat inside ;当前接口指定为内部接口Router<config-if>#ip nat outside ;当前接口指定为外部接口Router<config>#ip nat inside source static [p] [port]Router<config>#ip nat inside source static 10.65.1.2 60.1.1.1Router<config>#ip nat inside source static tcp 10.65.1.3 80 60.1.1.1 80Router<config>#ip nat pool p1 60.1.1.1 60.1.1.20 255.255.255.0Router<config>#ip nat inside source list 1 pool p1Router<config>#ip nat inside destination list 2 pool p2Router<config>#ip nat inside source list 2 interface s0/0 overloadRouter<config>#ip nat pool p2 10.65.1.2 10.65.1.4 255.255.255.0 type rotaryRouter#show ip nat translationrotary 参数是轮流的意思,地址池中的IP轮流与NAT分配的地址匹配.overload参数用于PAT 将内部IP映射到一个公网IP不同的端口上.12.外部网关协议配置:routerA<config>#router bgp 100routerA<config-router>#network 19.0.0.0routerA<config-router>#neighbor 8.1.1.2 remote-as 20013.配置PPP验证:RouterA<config>#usernamepasswordRouterA<config>#int s0RouterA<config-if>#ppp authentication {chap|pap}[第三部分]PIX防火墙命令Pix525<config>#nameif ethernet0 outside security0 ;命名接口和级别Pix525<config>#interface ethernet0 auto ;设置接口方式Pix525<config>#interface ethernet1 100full ;设置接口方式Pix525<config>#interface ethernet1 100full shutdownPix525<config>#ip address inside 192.168.0.1 255.255.255.0Pix525<config>#ip address outside 133.0.0.1 255.255.255.252Pix525<config>#global <if_name> natid ip-ip ;定义公网IP区间Pix525<config>#global <outside> 1 7.0.0.1-7.0.0.15 ;例句Pix525<config>#global <outside> 1 133.0.0.1 ;例句Pix525<config>#no global <outside> 1 133.0.0.1 ;去掉设置Pix525<config>#nat <if_name> nat_id local_ip [netmark]Pix525<config>#nat <inside> 1 0 0内网所有主机<0代表0.0.0.0>可以访问global 1指定的外网.Pix525<config>#nat <inside> 1 172.16.5.0 255.255.0.0内网网段的主机可以访问global 1指定的外网.Pix525<config>#route if_name 0 0 gateway_ip [metric] ;命令格式Pix525<config>#route outside 0 0 133.0.0.1 1 ;例句Pix525<config>#route inside 10.1.0.0 255.255.0.0 10.8.0.1 1 ;例句Pix525<config>#static <inside, outside> 133.0.0.1 192.168.0.8表示内部ip地址,访问外部时被翻译成全局地址.Pix525<config>#static <dmz, outside> 133.0.0.1 172.16.0.8中间区域ip地址,访问外部时被翻译成全局地址.。

相关文档
最新文档