连接器专业术语中英文对照表.
连接器专业术语中英文对照表
连接器常用的专业术语1. 连接器：通常装接在电缆或设备上，供传输线系统电连接的可分离元件（转接器除外）。
2. 射频连接器：是在射频范围内使用的连接器。
3. 视频：频率范围在3HZ∽30MHZ之间的无线电波。
4. 射频：频率范围在3千HZ∽3000GHZ之间的无线电波。
5. 高频：频率范围在3MHZ∽30MHZ之间的无线电波。
6. 同轴：内导体具有介质支撑，结构上能在测量中采用频率范围内得到最小的内反射系数。
7. 三同轴：由具有公共轴线并且相互绝缘的三层同心导体组成的传输线。
8. 等级：连接器在机械和电气精密度方面特别是在规定的反射系数方面的水平。
9. 通用连接器（2级）：采用最宽的容许尺寸偏差（公差）制造，但仍能保证最低限度的规定性能和互配性的一种连接器。
注：反射系数的要求可规定，也可以不规定。
10.高性能连接器（1级）：按频率变化来规定反射系数极限值的一种连接器，通常所规定的尺寸公差不比相应的2级连接器严格，但是需要保证连接器满足反射系数的要求时，制造厂有责任选择较严的公差。
11.标准试验连接器(0级)：用来对1级和2级连接器进行反射系数测量的一种精密制造的具体类型连接器，对测量结果引起的误差可以忽略不计。
注：标准试验连接器通常是不同类型间转接器的一部分，而转接器与精密连接器连接构成测试设备的一部分。
12.密封12.1密封连接器：具有能满足规定的气体，潮气或液体密封性要求的连接器。
12.2隔障密封：防止与气体、潮气或液体沿着轴向进入连接器壳体内部的密封。
12.3面板密封：防止气体、潮气或液体通过安装孔进入固定或转接器壳体与面板之间的密封。
注：密封件通常作为独立产品提供。
12.4插合面密封：防止气体、潮气或液体进入一对插合连接器界面处的密封。
12.5气密封：满足IEC60068-2-17《基本环境试验规程第2部分：试验-试验Q：密封》中试验Qk规定要求的密封。
连接器的基本结构组成：连接器的基本结构件有①接触件；②绝缘体；③外壳（视品种而定）；④附件。
连接器专业术语中英文对照表
连接器常用的专业术语1. 连接器：通常装接在电缆或设备上，供传输线系统电连接的可分离元件（转接器除外）。
2. 射频连接器：是在射频范围内使用的连接器。
3. 视频：频率范围在3HZ∽30MHZ之间的无线电波。
4. 射频：频率范围在3千HZ∽3000GHZ之间的无线电波。
5. 高频：频率范围在3MHZ∽30MHZ之间的无线电波。
6. 同轴：内导体具有介质支撑，结构上能在测量中采用频率范围内得到最小的内反射系数。
7. 三同轴：由具有公共轴线并且相互绝缘的三层同心导体组成的传输线。
8. 等级：连接器在机械和电气精密度方面特别是在规定的反射系数方面的水平。
9. 通用连接器（2级）：采用最宽的容许尺寸偏差（公差）制造，但仍能保证最低限度的规定性能和互配性的一种连接器。
注：反射系数的要求可规定，也可以不规定。
10.高性能连接器（1级）：按频率变化来规定反射系数极限值的一种连接器，通常所规定的尺寸公差不比相应的2级连接器严格，但是需要保证连接器满足反射系数的要求时，制造厂有责任选择较严的公差。
11.标准试验连接器(0级)：用来对1级和2级连接器进行反射系数测量的一种精密制造的具体类型连接器，对测量结果引起的误差可以忽略不计。
注：标准试验连接器通常是不同类型间转接器的一部分，而转接器与精密连接器连接构成测试设备的一部分。
12.密封12.1密封连接器：具有能满足规定的气体，潮气或液体密封性要求的连接器。
12.2隔障密封：防止与气体、潮气或液体沿着轴向进入连接器壳体内部的密封。
12.3面板密封：防止气体、潮气或液体通过安装孔进入固定或转接器壳体与面板之间的密封。
注：密封件通常作为独立产品提供。
12.4插合面密封：防止气体、潮气或液体进入一对插合连接器界面处的密封。
12.5气密封：满足IEC60068-2-17《基本环境试验规程第2部分：试验-试验Q：密封》中试验Qk规定要求的密封。
连接器的基本结构组成：连接器的基本结构件有①接触件；②绝缘体；③外壳（视品种而定）；④附件。
中英文连接器用语44页word
连接器用语集(质量）中英日1 other part no. 不同现品现品相违2 other material 不同材料材料相违3 quantity shortage 数量不足数量不足4 mixed 异种混入异种混入5 broken 破损破损6 discrepant 不同相违7 illegible letters 文字不清晰文字不鲜明8 missing indication 忘记表示表示忘れ9 approval mark uua，csa标识 uua、csa表示10 inspection sheet 成绩书成绩书11 poor reeling 卷取不良巻き不良12 tangled 缠からみ13 reversed 卷反逆巻き14 defected splice 继续継ぎ15 back reel 往里卷里巻き16 direction off top 取出方法取り出し方法17 gap 上下距离ギャップ18 height,depth 高度，深度高さ、深さ19 location 位置位置20 width 宽度幅21 thickness 厚度厚さ22 outer diameter 外径外形（外寸）23 inner diameter 内径内径（内寸）24 angle 角度角度25 pitch 中心间距离ピッチ26 swage, chamfer 倒角面取り27 diagonal 对角尺寸対角寸法28 diameter 直径直径29 length 长度长さ30 symmetry 对称度対称度31 parallelism 平行度平行度32 perpendicularity 垂直度直角度33 true position 位置度真位置度34 flatness 平面度平面度35 concentricity 同轴度同芯度36 roundness 真圆度真円度37 coplanarity 平坦度平坦度38 straightness 直线度真直度39 push-on, push-off 插拔力挿抜力40 insertion force 插入力挿入力41 extraction force 引拔力引き抜き力42 normal force 接触力接触力43 retention force 保持力保持力44 fitness 固着力固着力45 spring back 复员力复元力46 strength 强度强度47 actuating force 开关作用力スイッチ作动力48 solder wicking 焊锡度半田上がり49 flux raise 焊剂フラックス上がり50 conductivity 导通性导通性51 contact failure 接触不稳定接触不安定52 contact resistance 接触抵抗接触抵抗53 lighting 点灯点灯54 short circuit 短路短络55 burning 烧伤焼损56 dielectric 耐电压耐电圧57 insulation resistance 绝缘抵抗絶縁抵抗58 chip & scrap 切粉切粉59 scrap 废弃スクラップ60 die & tool mark 打痕ダイマーク61 crack 破裂割れ62 burrs 毛刺バリ63 flaw/scratch 伤/划伤伤／削れ64 inclusion 异物混入异物混入65 adhered substance 异物附着异物付着66 dirty 脏污污れ67 discoloration 变色変色68 discrepant color 不同颜色色违い69 coloring 颜色不均色调むら70 crushed 压坏溃れ71 breakage 破损破损72 bent, deformed 弯曲、变形曲がり、変形73 shape 形状形状74 rusty 锈锖75 marking 打印マーキング76 camber 反挠度キャンバー77 curly 卷取カール78 twist 扭转ねじれ79 excess adhered bond 接着剂过多接着剤过多80 chipping 缺损欠け81 plating thickness 镀层厚度メッキ厚82 porosity 砂眼ポロシティー（有孔性）83 peeling 剥离剥离84 solderability 焊锡附着性半田付き性85 not plated 露出底质地肤露出86 corrosion 腐蚀腐食87 discrepant plating 镀层不同メッキ违い88 tensil strength 拉力强度引张强度89 stiffness 耐力耐力90 hardness 硬度硬度91 extension 伸展伸び92 bend strength 折曲强度折り曲げ强さ93 short shot 注塑不足ショート・ショット94 weld line 熔接线ウェルド・ライン95 sink 逊色ひけ96 warp 弯度そり97 bubble 气泡気泡98 silver streak 银色シルバー99 whity 白化白化100 blistered 胀ふくれ99 whity 白化白化100 blistered 胀ふくれ101 chip 缺损欠け102 breakage 折断折れ103 cut 切断カット104 ejector mark 喷射标记エジェクター・マーク105 burnning 烧焼け106 core misassembly 组装错误组合わせ违い107 filled mold/excessive 型芯破损/多料コア破损/余肉108 dregs stopped 碎屑堆积カスつまり109 moisture ratio 水分率水分率110 torn 撕裂ちぎれ111 flow mark 波纹フローマーク112 compo parts short 缺少部品欠品113 actuation 动作作动114 install 安装取付115 adhesive 接着接着116 twisted 旋转度ツイスト117 color code 条形码カラー・コード118 brazing 焊接ろう付け（ブレージング）119 various defects 多种不良多种の不良120 poor insertion 插入不良挿入不良121 poor crimping 压着不良圧着不良122 poor termination 压接不良圧接不良123 poor thread 螺纹不良ねじ切り不良124 poor tapping 分接头不良タップ不良125 adjusting 调整调整126 material change 材料交换材料交换127 operator error 作业错误作业128 blacken 染黑黒染め129 poor coating 镀层不良メッキ不良130 heat treatment 热处理热处理131 missed finish 未加工未加工132 poor buff 光洁度不良バフ不良133 passivate 不导体处理不导体处理1 package, paper 包装箱，纸包装箱、纸2 label 标签ラベル3 letters 文字文字4 reel 卷轴リール5 tube 塑料管チューブ6 tray 托盘トレイ7 emboss[im'bɔ:s] tape 包装带エンボス・テープ8 blister pack 泡沫箱ブリスター・パック9 receptacle 雌（母）リセ10 socket 插座ソケット11 contact leaf 叶形リーフ12 plug插头プラグ13 tab扁形タブ14 pin 销形ピン15 post 导向柱形ポスト16 cantilever支承梁カンチ・レバー17 tine 尖端タイン18 bow 弓形ボウ19 rolling 旋转ローリング20 tongue 舌部トング（舌部）21 lance 矛形锁定ランス22 dimple ['dimpl]坑形锁定ディンプル23 emboss [im'bɔ:s]压模エンボス24 stopper 塞子ストッパー25 dimple hole 坑式洞ディンプル・ホール26 stabilizer ['steibilaizə]安定面スタビライザー27 action area 活动部アクション部28 shoulder 肩部ショルダー29 rib 肋リブ30 wire barrel['bærəl]金属线ワイヤ31 insulation [.insju'leiʃən] barrel 绝缘インシュレーション32 serration 非光滑面セレーション33 kick back 反冲キック・バック34 transition 转换部トランジション35 v slot v型狭孔ｖスロット36 barrel step 桶形级板バレル・ステップ37 bell mouth 喇叭口ベル・マウス38 splice 接头スプライス39 carrier 连桥部分キャリア40 carrier hole 连桥部孔キャリア・ホール41 slot 狭孔スロット42 cut off tab 切断剩余部カット・オフ・タブ43 i.d. mark 特殊标记ｉ．ｄ．マーク44 amp mark amp 标记ａｍｐマーク45 bead 突起部ビード46 seam 接缝シーム47 notch 刻痕ノッチ48 circuit cavity 回路孔回路キャビティ49 pitch 间距ピッチ50 circuit wall 隔离壁极间壁51 outer surface 外侧面外侧面52 edge 边缘エッジ53 gate 出入口ゲート54 card slot 卡缝カード・スロット55 post hole 导向柱孔ポスト穴56 circuit number 电路号码回路番号57 mold i.d. mark 模穴号标记キャビティ・マーク58 inner surface 内侧面内侧面59 mate area 嵌合侧はめあい部60 window 窗口窓61 flange area 凸缘部フランジ部62 hinge area 铰链部ヒンジ部63 housing lance 塑料件矛式锁定ハウジング・ランス64 sphincter 括约スフィンクター65 leg 脚、腿レグ66 wing 翅ウィング67 rib 肋リブ68 lance hole 矛式孔ランス穴69 polarization 极心ポラリゼーション70 bridge 桥ブリッジ71 indent 刻印インデント(雕り込み）72 detent 爪デテント73 ear 耳耳74 mounting hole 组装孔取付け穴75 board lock area 板锁定部ボード・ロック部76 housing 塑料件ハウジング77 contact 端子コンタクト78 shell 铁壳シェル79 solder peg 焊锡耳ソルダー・ペグ80 retention leg 保留腿リテンション・レグ81 tine plate 尖端板タイン・プレート82 g-plate 接地板ｇプレート83 guide post 导向柱ガイド・ポスト84 guide socket 导向插座ガイド・ソケット85 slider 滑动板スライダー86 contact forming 端子两次加工コンタクト二次加工87 pre-insertion 予插入仮挿入88 final insertion 正式插入本挿入89 carrier cut 连桥切断キャリア・カット90 bending 弯曲曲げ91 resizing 修整修正92 soldering 焊锡半田付け93 inspection 检查検査94 packing 包装捆包95 brass 黄铜黄铜96 pre-tin brass 镀锡黄铜锡メッキ黄铜97 phos-bronze 磷青铜りん青铜98 pre-tin phos-bronze 镀锡磷青铜锡メッキりん青铜99 be-cu 铍铜ベリ铜100 pre-tin be-cu 镀锡铍铜锡メッキベリ铜101 au, be-cu 镀金铍铜金メッキベリ铜102 copper 铜铜103 ca-725 ca-725 ｃａ－７２５104 stainless steel 不锈钢ステンレス・スティール105 klf-5 kif-5 ｋｌｆ－５106 tin lead 焊锡半田锡107 pre-tin klf-5 镀锡klf-5 锡メッキｋｌｆ－５108 super phos-bronze 超磷青铜超りん青铜109 msp-1 msp-1 ｍｓｐ－１110 mf202r mf202r ｍｆ２０２ｒ111 pre-tin-cu msp-1 镀锡铜msp-1 锡铜メッキｍｓｐ－１112 max-251 max251 ｍａｘ２５１（りん青铜）113 z-klf-5 z-klf-5 ｚ－ｋｌｆ－５114 pre-tin z-klf-5 镀锡z-kif-5 锡メッキｚ－ｋｌｆ－５115 fpc fpc ｆｐｃ116 pcb(pc board) pc板ｐｃボード（プリント基板）117 nylon 尼龙ナイロン118 noryl ノリル119 pbt pbt ｐｂｔ120 dap dap ｄａｐ121 phenol 苯酚フェノール122 lcp lcp ｌｃｐ冲压类punch, press冲punching machine 冲床hydraulic machine油压机jack升降机decoiler整平机manufacture management制造管理stamping, press冲压feeder送料机rack, shelf, stack料架taker取料机to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped报废scrape ..v.刮;削robot机械手production line流水线packaging tool打包机packaging打包成型类well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口runner less无浇道sprue less 无射料管方式long nozzle延长喷嘴方式spur浇口;溶waste废料board广告牌sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理组装类assembly line组装线layout布置图conveyer流水线运\输带rivet machine拉钉机rivet gun拉钉枪screw driver起子electric screw driver电动起子hydraulic machine 液压机pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氩焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运\be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine/heat stake热熔机/热风枪processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods 退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机品质类qualified products, up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part来件不良exposed metal/bare metal金属裸露excessive defect过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格cosmetic defect外观不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑丝missing part漏件wrong part错件oxidation氧化defective threading抽芽不良poor staking铆合不良deficient purchase来料不良deficient manufacturing procedure制程不良cosmetic inspection外观检查inner parts inspection内部检查blister 气泡angular offset 角度偏差dent 压痕scratch 刮伤deformation 变形filings 铁削defective label 不良标签abrasion 磨损breaking. (be)broken,(be)cracked 断裂short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delaminating起鳞speckle斑点mildewed =moldy = mouldy发霉burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质shrinking/shrinkage缩水mixed color杂色fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍impurity 杂质mismatch 错位failure, trouble 故障deformation 变形rust 生锈peel 脱漆shrink 缩水contamination 脏污water spots 水渍gap 间隙label error 标签错误missing label 漏贴rejection criteria 拒收标准suspected rejects 可疑庇abrasion 损伤、磨损texture surface 印花纹表面streak 条纹stains 污点blotch 斑点discoloration 脱色inclusion 杂质slug mark 压痕dirt grime 灰尘blush 毛边薄膜sink 下凹hickey 漏漆labels and logos 贴纸与商标configuration labels 组合贴纸corrugated container 瓦摆纸箱delaminating 脱层splattering 散点gouge 锉孔puckering 折痕通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |\'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位human resources department人力资源部head count 人头数production department生产部门planning department企划部qc section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日color management 颜色管理visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量physical count quantity帐面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 电脑外壳(组件)personal computer enclosure 电脑机箱产品front plate前板rear plate后板chassis |\'∫鎠i| 基座bezel panel面板hood 上盖base pan 基座bezel 面板riser card 扩充卡flat cable 排线top driver cage 上磁架bottom driver cage 下磁架resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑胶件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程表单production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套band-aid创可贴industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机club car高尔夫球车plate电镀power button电源按键reset button重置键forklift叉车workshop traveler 天车trailer =long vehicle拖板车hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate座标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉伸work cell/work shop工作间sub-line支线bottleneck 瓶颈模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模stage die工程模compound die复合模shearing die剪边模riveting die铆合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 换模to fix a die装模to repair a die修模punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)upper supporting blank上承板upper padding plate blank上垫板top plate上托板（顶板）top block上垫脚stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块die locker锁模器pressure plate =plate pinch压板thickness gauge厚薄规cutting die, blanking die冲裁模die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条panel board镶块to load a die装上模具to unload a die 御模具active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块pilot导正筒trim剪外边pierce剪内边pocket for the punch head挂钩槽slug hole废料孔radius半径shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺丝form block折刀round pierce punch =die button圆冲子shape punch =die insert异形子stock located block定位块metal plate钣金miller铣床grinder磨床tolerance公差score =groove压线sliding block滑块lathe车active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板capability能力parameter参数factor系数driller钻床set up die架模height of die setting up架模高度analog-mode device类模器inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves =spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套press specification冲床规格die height闭模高度flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝stripper plate脱料板piston活塞handle mold手持式模具flash mold溢流式模具positive mold挤压式模具split mold分割式模具die lifter举模器top stop上死点bottom stop下死点one stroke一行程to continue, cont.连动to grip(material)吸料location lump, locating piece, location block定位块reset复位to file burr 锉毛刺embedded lump |in\'bed| |l赞p|镶块stamping-missing漏冲to tight a bolt拧紧螺栓to loosen a bolt拧松螺栓punched hole冲孔to cut edge =side cut =side scrap 切边to bending折弯to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake铆合designing, to design设计design modification 设计修改成gauge(or jig)治具pedal踩踏板stopper阻挡器flow board流水板torque扭矩spline =the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的forming成型(抽凸,冲凸)draw hole抽孔emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线stamp letter冲字(料号)tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图connecter 连接器cable 导线wire-to-wire 线至线wire-to-board 线至板mini-universal 小型通用circular plastic connectors 塑料密封环连接器dl (dual-leaf) contact sockets 双叶式触点插座drawn spring dip contact socket 弹簧触点插座zig-zag package sockets 锯齿形封装插座positive lock connectors 确立锁定连接器coax mix 同轴混合shielded circular din connectors 屏蔽式圆型din连接器memory card connectors 记忆装置插结连接器simm sockets 单列记忆模件插座low profile 低高度cis (commercial interconnection system) 商用连接系统hinge connectors 铰连连接器card-edge connectors 边缘插接连接器euro card connectors 欧式插接连接器modular interconnection system 组合连接系统interconnection system 互连系统rf connectors 射频连接器twin-ax connectors 双轴互连系统low profile coaxial tap 低高度型有源同轴电缆线器4 position data connectors 4位数据连接器insulation and wire support 绝缘体及导线套ring-tongue terminals 环形舌端子wire size range 线径范围slotted-tongue terminals 叉式舌片端子butt splices 对头接头dentented ring-tongue terminals 卡爪环舌型端子fits tab thickness 配合接片厚度accepts terminals 配合端子crimp-type tabs 压接式接片free-hanging and panel-mount applications 自由悬挂及面板装嵌适用cable clamp 电缆钳位夹pc board vertical pin headers 垂直接插式接插头组件pc board right-angle pin and socket headers 水平接插式接插头组件panel-mount connectors 面板装嵌连接器insulation displacement plugs 绝缘位移连接插头dielectric withstanding voltage 介质承受电压free-hanging type cap housings 自由悬挂式套座壳体semiautomatic crimping machine 半自动压接机power supply 供给功率air pir pressure 气压panel mount type cap housings 面板装嵌套座壳体post header for printed circuit board 印刷底板用柱头mass termination assemblies 集体端接组件post header assemblies 接插柱头组件polarized right angle post header assembly 有极向性水平接插柱头组件friction lock 锁尖装置sigle leaf connectors 单叶片连接器cpc (circular plastic connectors) 塑料密封环型连接器ceimp snap-in contacts 压接式套入触点socket with straight solder tails 直立焊脚插座retention feature solder tails 弯曲焊脚sockets with retention feature solder tails 面板附定曲脚插座high pressure tin (hpt) sockets 镀锡高压芯片positive lock retention feature 彻底锁定装置plug-grounding indents 插头外罩接地凹位solder cup connector 焊杯触点连接器straight exit rfi/emi shield for jacketed cable 直线引出rfi/emi 屏蔽外壳外套导线束适用backshell assembly 后部外壳组件board-mount connectors with threaded inserts and board locks 底板安装连接器附内丝牙及板扣board-mount receptacles 底板安装插座non-polarized receptacles 无定位型插座handset plug assembly 电话线插头组件line cord plug assembly 听筒插头组件1、表面间连接：interlayer connection2、层间连接：interlayer connection3、内层连接：innerlayer connection4、非菜单面连接：nonfunctional interfacial connection5、跨接线：jumper wire6、节(交)点：node7、附加线：haywire8、端接(点)：terminal9、连接线：terminated line10、端接：termination11、连接端：pad, land12、贯穿连接：through connection13、支线：stub14、印制插头：tab15、键槽：keying slot16、连接器：connector17、板边连接器：edge board connector18、连接器区：connector area19、直角板边连接器：right angle edge connector20、偏槽口：polarizing slot21、偏置端接区：offset terminal area22、接地：ground23、端接隔离(空环)：terminal clearance24、连通性：continuity25、连接器接触：connector contact26、接触面积：contact area27、接触间距：contact spacing28、接触电阻：contact resistance29、接触尺寸：contact size30、组件引腿(脚)：component lead31、组件插针：component pin32、最小电气间距：minimum electrical spacing33、导电性：conductivity34、边卡连接器：card-edge connector35、插卡连接器：card-insertion connector36、载流量：current-carrying capacity37、蹯径：path38、最短路径：shortest path39、关键路径：critical path40、倒角：miter41、串推：daisy chain42、斯坦纳树：steiner tree43、最小生成树：minimum spanning tree (mst)44、瓶颈宽度：necked width45、短叉长度：spur length46、短柱长度：stub length47、曼哈顿路径：manhattan path48、连接度(性)：connectivity希望以上资料对你有所帮助，附励志名言3条：1、宁可辛苦一阵子，不要苦一辈子。
中英文对照表(连接器常用术语)
耳扣 塑膠(本體） 模穴 咬花 塑膠(原料） 毛邊 翹曲 連 蓋子 接 吸件蓋子 麥拉
五金件 英文 中文
彈片 接地柱 鉚釘 接地pin 螺絲 方pin 魚叉邊 防護/屏蔽 焊接地片 叉片 鐵環 金屬
包材 中文
脆盤 管裝 載帶 紙箱 材料 包裝 管裝+CAP 載帶+CAP 脆盤+CAP 袋子 TRAY TUBE REEL CARTON MATERIAL PACKAGE TUBE Package + CAP REEL Package + CAP TRAY Package + CAP BAG 連接器 公座 母座 插頭 共面度 位置度 信號pin 接觸pin數 前接触 下接触 上接触 配合高度 垂直的 水平的 90度折彎 彎曲 彎腳 直腳 凸點 無凸點 有凸點 貼板型 線路板 內圓直徑 雙排 pin距
其它 英文
CONNECTOR MALE FEMALE PLUG COPLANARITY TOLERANCE GEOMETRIC DIMENSIONING SIGNAL PIN CONTACTS FRONT CONTACT TOP CONTACT BOTTOM CONTACT MATING HEIGHTE VERTICAL HORIZONTAL RIGHT ANGLE CAMBER KINK STRAIGHT NOS W/O NOSE WITH NOSE SMT TYPE PCB ID DOUBLE ROW PITCH
器 常 用 術 語
ACTUATOR HOUSING CAVITY TEXTURE PLASTIC FLASH CAMBER COVER CAP MYLAR
英文
SPRING GROUNDING LEG RIVET GROUNDING PIN SCREW SQUARE PIN (SQ.) HARPOON SHELL TERMINAL BRASS BERYLLIUM ALLOY BURR COPPER ALLOY STAINLESS STEEL CHECKING CHECK BURR FREE SHIELDING SOLDER LATCH FORK MATEL RING METAL
连接器专业知识总结(中英文)
音频 和
视频 连接 器
Audio & Video Connector
HDMI连接 器
DVI连接器 Hssdc2连 接器 Sata连接 器 DIN连接器 Display Port连接 器 IEEE1394 连接器 屏蔽数据 链路 LVDS 连接器(LC EDI) RJ11连接 器 RJ14连接 器
HDMI Connector
CONNECTOR 的专业知识
一 连接器的定义 Definition of Connector
A connector is a coupling device that joins electrical terminations to create an electrical circuit. Connectors enable contact between wires, cables, printed circuit boards, and electronic components.
电源 连接 器
电路 连接 器
射频 同轴 连接 器 光纤 连接 器 汽车 连接 器
照明 连接 器
Modular Jacks & Plug
Power Connector
Circular Connector
RF Coax Connector
MRJ21连接 器 RJ22连接 器 RJ25连接 器 RJ45连接 器 圆形电源 电池连接 器和电池 组 背板电源 电源汇流 条连接器 面板和PCB 插座 电源端子 矩形电源 圆形电源 连接器 标准圆形 连接器 电路RJ45 连接器 DIN连接器 射频连接 器
MRJ21 Connector
RJ22 Connector
RJ25 Connector
连接器常见术语解析(中英互译)
连接器常见术语解析（中英互译） 连接器用词汇： ● Alloy（合金）：两种或多种金属的组合。
● Contact（端子）：一连接构件的电传导部位，被设计予提供电气之接触或分离的接点（位置）。
●Contact area（接触区域）：和IC引线或接点造成电气连接的接触表面。
●Contact aesistance（接触电阻）：在连接位置处的电阻，是由端子形状，接触面积，电镀和正向力所定。
● DIN：在电子工业界，特定某种连接器特性的欧洲标准。
● Gauge（量规）：定义线径大小的一数字。
● Header：包含于绝缘体中一或多排的圆形或方形插梢。
● IC（Integrated Clrcuit）种体电路。
●IDC（绝缘体被剥除的连接器）：迅速和可信赖地大量连结平坦网线至一连接器的方法。
●InserTIon force（插入力）：插一公的引线进入母的插座所需要的力。
● InserTIon resistance（绝缘阻抗）：两端子间绝缘体所能承受的阻抗值。
● Insulater（绝缘体）：一种非常差的电导体材料。
一种介电材料。
● Mixroinch（微英英寸）百万分之一英寸，用于电镀厚度。
●Package（封装）一种体电路晶片被相互连接至外部导线架和使其避免受损的状况。
●PlaTIng（电镀）：电力性沉体非常薄和精确厚度的金属于底材金属的方法。
● PCB（印刷电路板）：也以P.C.Board或Board称之 ●PolarizaTIon（极性）端子和引线的排列，其禁止插头和插座的不适合耦合。
●Resistance（阻抗）：电流流通过介质，其移动的难易程度。
Plating（盐水喷雾试验）：一种用发测试连接器电镀或者气密性的腐蚀性试验。
●Shell（壳）：引线插座的外壳，经常是用铁壳制成，其被精密机制的以固持一端子插入件。
●Stand off（热高装置）：一连接器底部的凸出结构，用以提高连接器离开印刷电路板，而帮助焊锡填充空间的形式，板子的检验和助焊剂的清除和清洗。
连接器英文专业类术语
>>技术支持 - 连接器英文专业类术语冲压类punch, press冲punching machine 冲床hydraulic machine油压机jack升降机decoiler整平机manufacture management製造管理stamping, press冲压feeder送料机rack, shelf, stack料架taker取料机to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped |’skr鎝id|报废scrape ..v.刮;削robot机械手production line流水线packaging tool打包机packaging打包成型类well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head鉋尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头鉤销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口runner less无浇道sprue less 无射料管方式long nozzle延长喷嘴方式spur浇口;溶waste废料board看板sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理组装类Assembly line组装线Layout布置图Conveyer流水线运输带Rivet machine拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Hydraulic machine 液压机Pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氬焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运be put in storage入库packing包装staker = riveting machine铆合机教你如何用WORD文档(2012-06-27 192246)转载▼标签：杂谈1. 问：WORD 里边怎样设置每页不同的页眉？如何使不同的章节显示的页眉不同？答：分节，每节可以设置不同的页眉。
连接器术语中英文对照
连接器术语中英⽂对照以下是以Starline系列为例的安费诺⼯业连接器部分术语中英⽂对照。
NO.English Name中⽂名称1Double lead Acme Thread双道梯形螺纹2Pressure Pad压板3Grommet密封胶圈4Mechanical clamp nut机械压紧螺母5washer垫圈6adapter连接套管7male insert/pin insert插针胶芯组件8pin contacts插针9coupling nut连接螺母10environmental cover male插头防护盖11environmental cover female插座防护盖12square flange receptacle⽅形法兰插座13flange gasket法兰垫⽚14female insert/socket insert插孔胶芯组件15scoket contacts插孔16insert clamp nut胶芯压紧螺母17conduit adapter管式套管18potting sleeve注胶衬套19basket weave grip织篮式电缆夹头20gland nut压紧螺母21straight plug直插头22square flange mounted plug法兰安装式插头23plastic dustcap塑胶防尘盖24junction box接线盒25gland格兰26Potting防爆胶27boot塑胶套筒28insert configurations胶芯排布29insertion tools插⼊⼯具30removal tools取出⼯具31contact crimping tools压接钳32Backcap后盖33Grip夹头34Cap 防尘盖35Cable电缆36Chain ring链环37Chain eyelet链形孔38crimp压接39Contact端⼦40Connector连接器41Clamp nut夹紧螺母42Coupling nut连接螺母43Insert胶芯44Jack插座45Jacket 护套46Label/ tag标签47PIN插针48Shell 外壳49Seal密封圈50Solder 焊接51Sleeve套筒52Snap ring卡环53wire电线。
连接器产品承认书常用名词中英文对照表
Finalinspection / FQC
冲制
Coining
切削加工
Cutting
冷锻
Cold forging
压铸
die-casting
滚丝/搓丝
Threading
除油
Deoiling
去毛刺
Removingburr
打点、打扁
Dotting、Stavein
预处理
Pre-processing
电镀
Quality Control(QC)
项目
Item
流程图
Flow chart
过程名称
Process name
品质特性
Quality Speciality
项目
Item
标准
Standard
确认要领
Sampling-affirmed
测定工具
Mensuration Tools
检测频率
Sampling frequency
作业指导书
Operatinginstruction
标准操作程序
Standard Operating Procedure（SOP）
电镀品质检验规范
Standard of platingqualityinspection
最终检验基准书
FQC standard
千分尺
Micrometer
游标卡尺
Verniercaliper
绝缘电阻
Insulation resistance
接触电阻
Contact resistance
耐电压
Withstanding voltage
耐热性
HeatEndurance
连接器专业术语中英文对照表
连接器专业术语中英文对照表Prepared on 22 November 20201.：通常装接在电缆或设备上，供传输线系统电连接的可分离元件（转接器除外）。
2.射频连接器：是在射频范围内使用的连接器。
3.视频：频率范围在3HZ∽30MHZ之间的无线电波。
4.射频：频率范围在3千HZ∽3000GHZ之间的无线电波。
5.高频：频率范围在3MHZ∽30MHZ之间的无线电波。
6.同轴：内导体具有介质支撑，结构上能在测量中采用频率范围内得到最小的内反射系数。
7.三同轴：由具有公共轴线并且相互绝缘的三层同心导体组成的传输线。
8.等级：连接器在机械和电气精密度方面特别是在规定的反射系数方面的水平。
9.通用连接器（2级）：采用最宽的容许尺寸偏差（公差）制造，但仍能保证最低限度的规定性能和互配性的一种连接器。
注：反射系数的要求可规定，也可以不规定。
10.高性能连接器（1级）：按频率变化来规定反射系数极限值的一种连接器，通常所规定的尺寸公差不比相应的2级连接器严格，但是需要保证连接器满足反射系数的要求时，制造厂有责任选择较严的公差。
11.标准试验连接器(0级)：用来对1级和2级连接器进行反射系数测量的一种精密制造的具体类型连接器，对测量结果引起的误差可以忽略不计。
注：标准试验连接器通常是不同类型间转接器的一部分，而转接器与精密连接器连接构成测试设备的一部分。
12.密封密封连接器：具有能满足规定的气体，潮气或液体密封性要求的连接器。
隔障密封：防止与气体、潮气或液体沿着轴向进入连接器壳体内部的密封。
面板密封：防止气体、潮气或液体通过安装孔进入固定或转接器壳体与面板之间的密封。
注：密封件通常作为独立产品提供。
插合面密封：防止气体、潮气或液体进入一对插合连接器界面处的密封。
气密封：满足IEC60068-2-17《基本环境试验规程第2部分：试验-试验Q：密封》中试验Qk规定要求的密封。
连接器的基本结构组成：连接器的基本结构件有①接触件；②绝缘体；③外壳（视品种而定）；④附件。
连接器行业专业英语高频词句
连接器行业专业英语高频词句（中英对照）Connecter 连接器Cable 导线Wire-to-wire 线至线Wire-to-board 线至板Mini-universal 小型通用Circular plastic connectors 塑料密封环连接器DL (dual-leaf) contact sockets 双叶式触点插座Drawn spring DIP contact socket 弹簧触点插座Zig-zag package sockets 锯齿形封装插座Positive lock connectors 确立锁定连接器Coax mix 同轴混合Shielded circular DIN connectors 屏蔽式圆型DIN连接器Memory card connectors 记忆装置插结连接器SIMM sockets 单列记忆模件插座Low profile 低高度CIS (commercial interconnection system) 商用连接系统Hinge connectors 铰连连接器Card-edge connectors 边缘插接连接器Euro card connectors 欧式插接连接器Modular interconnection system 组合连接系统interconnection system 互连系统RF connectors 射频连接器Twin-Ax connectors 双轴互连系统Low profile coaxial tap 低高度型有源同轴电缆线器4 position data connectors 4位数据连接器Insulation and wire support 绝缘体及导线套Ring-Tongue terminals 环形舌端子Wire size range 线径范围Slotted-Tongue terminals 叉式舌片端子Butt splices 对头接头Dentented Ring-Tongue terminals 卡爪环舌型端子Fits tab thickness 配合接片厚度Accepts terminals 配合端子Crimp-type tabs 压接式接片Free-Hanging and Panel-Mount Applications 自由悬挂及面板装嵌适用Cable clamp 电缆钳位夹PC Board vertical pin headers 垂直接插式接插头组件PC Board Right-Angle pin and socket headers 水平接插式接插头组件Panel-Mount connectors 面板装嵌连接器Insulation Displacement plugs 绝缘位移连接插头Dielectric withstanding voltage 介质承受电压Free-Hanging type cap housings 自由悬挂式套座壳体Semiautomatic crimping machine 半自动压接机Power supply 供给功率Air pir pressure 气压Panel mount type cap housings 面板装嵌套座壳体Post header for printed circuit board 印刷底板用柱头Mass termination assemblies 集体端接组件Post header assemblies 接插柱头组件Polarized right angle post header assembly 有极向性水平接插柱头组件Friction lock 锁尖装置Sigle leaf connectors 单叶片连接器CPC (circular plastic connectors) 塑料密封环型连接器Crimp Snap-In contacts 压接式套入触点Socket with straight solder tails 直立焊脚插座Retention feature solder tails 弯曲焊脚Sockets with retention feature solder tails 面板附定曲脚插座2High Pressure Tin (HPT) sockets 镀锡高压芯片Positive lock retention feature 彻底锁定装置Plug-Grounding Indents 插头外罩接地凹位Solder Cup connector 焊杯触点连接器Straight Exit RFI/EMI shield for Jacketed cable 直线引出RFI/EMI屏蔽外壳外套导线束适用Backshell assembly 后部外壳组件Board-Mount connectors with threaded inserts and board locks 底板安装连接器附内丝牙及板扣Board-Mount Receptacles 底板安装插座Non-Polarized Receptacles 无定位型插座Handset plug assembly 电话线插头组件Line cord plug assembly 听筒插头组件射频同轴连接器RF coaxial connector1.按尺寸分类 Connector types by size●标准连接器standard connector●小型连接器miniature connector●微型连接器sub-miniature connector●超小型连接器micro-miniature connector2. 结构和安装类型 Connector configurations & mounting styles2.1接电缆的连接器 Cabled connector●直式 straight●弯式 right angle （直角）●穿墙式 bulkhead n. 隔壁,防水壁,分壁2.2不接电缆的连接器 Uncabled connector●PC板安装 PC mount●表面贴装 surface mount●边缘安装（偏腿）end launch●法兰安装 flange mount3. 联接机构 Coupling mechanism●螺纹联接 threaded connection（e.g. SMA）●卡口式联接 bayonet coupling（e.g. BNC）●推入式联接 snap-on coupling（e.g. MMCX）●快速锁紧联接 quick-lock coupling（e.g. QMA）●滑入式联接 slide-on coupling （e.g. BMA）4. 组成部件 Parts●壳体 body/shell/housing●绝缘子 insulator●夹头绝缘子 clamp top insulator●中心接触件 center contactａ．插针 male/pinｂ．插孔 female/jack●中心导体 center conductor●内导体 inner conductor●外导体 outer conductor●插座/插口 jack-panel jack 面板插口/插座-bulkhead jack 穿墙插座4●插头 receptacle5. 材料 Material●黄铜 copper●铍青铜 beryllium copper●锡磷青铜 phosphor bronze●聚四氟乙烯 PTFE polytetrafluoroethylene 特氟纶teflon ●不锈钢 stainless steel●合金 alloy●实心聚乙烯 solid PE●泡沫聚乙烯 foam PE /cellular polyethylene●白铜 white bronze●硅橡胶 silicon rubber●裸铜 BC=bare copper●易切削黄铜free cutting brass●稀土磁铁rare earth magnet●铝箔 aluminium foil●基材 base material●FR-4板材 FR-4 plate●硅脂 silicon grease●润滑硅脂 lubricating silicone grease6. 电镀 Plating/finishing●镀金 gold plated●镀镍 nickel plated●钝化 passivated●镀三元合金 SUCO plating●镍磷合金（无磁镍）镀层 SUCOPRO●铜，锡，锌镀层 copper-tin-zinc plating●滚镀 barrel plating●合金电镀 alloy plating7. 电气特性 Electrical characteristics●阻抗(欧姆) impedance （ohms）ａ．特性阻抗 characteristic impedanceｂ．标称阻抗 nominal impedance●频率范围 frequency range●工作频率 operating frequency●工作电压 working volt●额定电压 voltage rating●介质耐压 DWV=dielectric withstanding voltage (如:最大/小有效值为ａ伏 e.g. ａＶｒｍｓ．ｍａｘ／ｍｉｎ）●海平面耐电压：proof voltage at sea level●射频泄露 RF leakage●绝缘电阻 insulation resistance●插入损耗 insertion loss●电压驻波比 VSWR6●额定热电流 rated thermal current●介电常数 dielectric constant●击穿电压 breakdown voltage●额定电流 current rating●电容 capacitance●电感 inductance●电晕损耗 corona loss●熄灭电压 extinction voltage●屏蔽效应 shielding efficiency●低损耗 low loss8. 机械特性Mechanical characteristics●耐久性（次数）durability/mating life（cycles）●电缆保持力 cable retention force●啮合力 engagement force●分离力 separation force/ disengagement●轴向力 axial force ( insertion & withdrawal 插入&抽出力) ●扭矩 torque●径向扭矩力 radial torque●弯曲力矩 bending moment●弯曲半径 bending radius●抗张强度 tensile strength●机械应力 mechanical stress●机械互换性：mechanical compatibility●中心接触件固定性 center contact captivation●制动 cathers mit9. 环境性能及试验Environmental characteristics & test●工作温度范围 operating temperature range●贮存温度 storage temperature●密封，透气/不透气 sealing，hermetic/non-hermetic●防潮 moistureproof/ dampproof●耐湿 humidity resistance●防水 waterproof●耐高温 high temperature resistance●耐热性 heat resistance●抗腐蚀性 corrrosion resistance●阻燃 flame resistant●抗风化，耐风雨，不受气候影响的 weather proof●热冲击 thermal shock●冲击 shock●振动 vibration●稳态湿热 damp heat, steady state●恒温 costant temperature●大气压（力），气压 barometric pressure●热处理，低温退火 annealing8●盐雾试验 salt mist/spray test●高压绝缘试验,闪点试验,火花试验 flash test●破坏性试验 destructive test●气密性试验 air tightness test●放电试验 discharge test10. 附件 Accessory●线夹 crimp ferrule●垫片 gasket●热缩管 heat shrink tubing/ heat-shrinkable tubing ●护线套 barrel crimp●衬套 bushing/braid clamp●卡环 lock ring/ snap ring●卡圈/弹簧卡环/压紧圈/挡圈 retainer ring●卡圈 collar●限位环 spacing ring/ stop collar●防晃圈 anti-rock ring●弹性接触件 resilient contact●锁销 lockpin●锁紧垫圈 lock washer●弹簧/性垫圈 spring washer●密封圈 seal ring●开口垫圈 slotted washer●防尘帽 dustproof cover/ dust cap●螺母 nut/screw nut●螺纹套筒 threaded sleeve●滚花螺母 knurled nut●直纹滚花 straight knurls●网纹滚花 crossed knurls●防松螺母/自锁螺母 locknut●锁紧螺母，止动螺母，压紧螺母 jam nut●紧固螺母 clamp nut●螺丝钉screw●法兰盘/凸缘盘 flange plate●橡胶圈 gum ring●纯胶管，软管 gum rubber tubing●连接套 barrel splice / joint sleeve●波导管 waveguide●弹簧夹 spring finger●弹簧片 spring lamination●紧固件 fixture/fastener●紧固螺栓 fastening bolt/ binding bolt●密封塞子 sealing plug●密封盖 sealing cover●匹配针 matched pin10●两芯电源插座 2-Core Socket●无源元件 passive component11. 工装夹具 Work fixture●夹具 clamping yoke●冲压工具 stamping tool●去毛刺工具 deburr tool●螺丝刀 screwdriver●平口螺丝刀 slotted screwdrier●十字花螺丝刀 phillips screwdrier●铆合机 staker / riveting machine ●翻边器/卷边器 hemmer/fold back tool ●钳子/镊子 pliers●螺丝钳/夹钳 clamp●电缆钳 cable nipper●剪钳，老虎钳 cutting nipper●尖嘴钳 sharp-nose pliers●钢丝剪钳 wire nipper●锉刀 file●扳手 wrench●钢锯 hacksaw●铆钉钳 rivet clipper●铆钉机 rivet driver●整平器，剔除器 flush trimmer●修边模 flush trim die●卡接槽口 clamping Slot●卡接工具 clamping cool●卡线钳 clamping pincers●力矩扳手 torque spanner●拧上 screw on●拧下 screw off射频同轴电缆及组件RF coaxial cable & cable assemblies1. 电缆类型 Cable types●超柔电缆 super-flexible cable●柔软电缆 flexible cable●半柔电缆 semi-flexible cable●半刚电缆 semi-rigid cable●跳/馈线 jumper/feeder cable●波纹电缆 corrugated cable2. 电缆组件类型 Cable assembly types●半刚电缆组件 semi-rigid cable assembly●半柔电缆组件 semi-flexible cable assembly●柔性电缆组件 flexible cable assembly●低损耗、稳相电缆组件 low loss & stable phase cable assembly12●毫米波电缆组件 millimeter wave cable assembly3.电缆设计Cable design3.1外导体设计 Design of outer conductor●单屏蔽 single screen●双屏蔽 double screen●绕包带和屏蔽层 tape and screen●金属管（半刚）tube(semi-rigid)●波纹 corrugated3.2 内导体设计 Design of inner conductor●实芯线 solid wire●绞合线 stranded wire●金属管 tube●螺纹管 screwed tube3.3 电缆结构 Cable construction●内导体 inner conductor●介质 dielectric●屏蔽层 shielding layer 编织层 braid layer/ply●护套 jacket3.4 电缆材料●镀锡铜 TC=tinned copper●铜包钢 BCCS=bare copper clad steel●镀银铜线 SC=silver covered copper●镀锡铜线 tinned copper●铜包钢线 CCS=copper clad steel●镀银铜包钢线 SCCS=silver covered copper clad steel●铜包铝线 BCCAl=bare copper clad aluminum●镀锡铜编织层 tinned copper braid●裸导线/无镀层导体 plain conductor●裸线, 裸导线 naked wire4. 电缆的装接方式 Cable attachment method4.1 柔软电缆 Flexible cable●压接式 crimp●夹持式 clamp4.2 半刚电缆 Semi-rigid cable●焊接式 solder5. 其它 Others●电缆旋转（挠动）cable rotation (nutation)●电缆拉伸 cable pulling●电缆弯曲 cable bending●电缆扭转 cable torsion/twisting●屏蔽线 shielded wire●双绞线 twisted pair●屏蔽双绞电缆 STP=shielded twisted pair●扁形软电缆 flat flexible cable●扁形双芯软线 flat twin flexible cord14●绕包带式 tape wrapping type●挤出型 extruded type●包带节距 tapping pitch射频同轴转接器RF coaxial adapter1. 转接器类型 Adapter types●系列间转接器：between-series adapter●系列内转接器：in-series adapter焊接用词汇●焊接槽 solder bucket●焊接柱 solder spill●焊片 solder gasket●焊锡圈 soldering ring●焊接孔solder eye●浸锡 tin soaked●焊锡丝 tin wire●漏焊 missing welding●虚焊 incomplete weld / weld defect/cold solder joint ●硬钎焊 solder brazing●焊割两用气焊枪 welding and cutting torch●焊接夹具 welding fixture●焊剂/焊料 welding fluid/ flux●焊接应力 welding stress●焊锡坑 solder cup●焊接涂料 welding paste●焊接部分 welding portion●无焊缝的 weldless●烙铁 soldering iron●烙铁架 iron stand●脱焊 loose weld●元器件表面焊接整洁，焊点圆滑 component surface is clearlywelded with smooth welding point●元器件无虚焊，漏焊，错贴 no cold solder joint, solder skipsand wrong welding of components●solder bath method 焊槽法技术要求＆其它 Techinical requirments & others●机械和电气基准面 mechanical and electrical referenceplane●符合RoHS要求 RoHS compliant (e.g.this part complies withRoHS)●括号中尺寸为参考尺寸dimensions with（）denote referencedimensions●铣槽和涨口/收口 slotted & flared/closed●去除毛刺 remove burrs/ deburr16●除锈 rust cleaning/removing●点铆 stamp●扩口 enlarge kerfs●毛边flash●编织层翻边 wrap the braid over the braid clamp(衬套)●外观，外形 appearance/outline●界面防水等级 interface waterproof level●标记内容：商标 型号 批次号 labels: trade mark，type， batchnumber●未注明公差按… non-specified tolerances according...●…要求为非磁性材料 …required to have non-magneticmaterial●导电环氧树脂回填 conductive epoxy back fill●外观检查：镀层表面无斑点和痕迹，界面无金属碎屑 Visualinspection: plating surface must be without spot and cinch marks; interface must be clean of metal chip●外观良好 good appearance●产品承认书 product acknowledgement●喷锡,黑油，无铅工艺 tin sprayed,black oil,lead free●无杂质 free of foreign matter●整涂覆 overall braid●现场安装field installation●两体结构two-body structure●尾部微带 rear strip●中心接触件弹性支撑center contact with elasticity support缩写和首字母缩写词 Abbreviations & acronyms:●连接器 CONN=connector●接触件 CONT=contact●超小D型连接器 D-sub CONN=D-subminiature connector●阴连接器/外壳 HSG=housing●印制电路板 PCB=print circuit board●产品型号，零件号 P/N=part number●订购单 P/O=purchasing order●数量 QTY=quantity●图纸 DWG=drawing●组件 ASS’Y=assembly●日期代码 D/C=date code●序号，编号 S/N=serial number●不良品，不合格品 NG=no good●不适用 N/A=not applicable●不可用，无法使用 N.A.=not available●直角 R/A=right angle●检验水平 IL=inspection level●可接受的 AC=acceptable18●可接受质量水平 AQL=acceptable quality level●退货，拒收 REJ=rejection●物料单，材料（零件）清单 BOM=bill of materials●无源交调 PIM=passive intermodulation●三阶交调 IM3= Intermodulation 3-tone●印制电路板PCB= printed circuit board●技术更改指令 ECO=Engineering Change Order●工程更改请求 ECR= Engineering Change Request●工艺更改通知单 PCN=Process Change Notice●制程能力/生产过程能力指数 CPK=capability of productionindex●过程工艺持续改进 CPI=continuous process improvement●大批量生成 MP=mass production●操作指南，使用说明书 OI=operating instruction●生产制造 MFG=manufacturing●作业指导书，制作规程 MI=manufacturing instruction●生产控制 PC=production control●质量保证 QA=quality assurance●质量控制 QC=quality control●统计过程管控 SPC=statistical process control●十亿分之一 PPB=part per billion●百万分之一 PPM=part per million●尽快 ASAP=as soon as possible●供参考 FYI=for your information●美国线规 AWG=American wire gauge(e.g. AWG23,意思就是23号线)●平均线规 AWG=Average wire gauge●部门 Dept.=department●有 W/=with●没有 W/O=without**瓦楞纸箱 corrugated carton/slotted carton20。
(整理)中英文连接器用语.
连接器用语集(质量）中英日1 other part no. 不同现品现品相违2 other material 不同材料材料相违3 quantity shortage 数量不足数量不足4 mixed 异种混入异种混入5 broken 破损破损6 discrepant 不同相违7 illegible letters 文字不清晰文字不鲜明8 missing indication 忘记表示表示忘れ9 approval mark uua，csa标识 uua、csa表示10 inspection sheet 成绩书成绩书11 poor reeling 卷取不良巻き不良12 tangled 缠からみ13 reversed 卷反逆巻き14 defected splice 继续継ぎ15 back reel 往里卷里巻き16 direction off top 取出方法取り出し方法17 gap 上下距离ギャップ18 height,depth 高度，深度高さ、深さ19 location 位置位置20 width 宽度幅21 thickness 厚度厚さ22 outer diameter 外径外形（外寸）23 inner diameter 内径内径（内寸）24 angle 角度角度25 pitch 中心间距离ピッチ26 swage, chamfer 倒角面取り27 diagonal 对角尺寸対角寸法28 diameter 直径直径29 length 长度长さ30 symmetry 对称度対称度31 parallelism 平行度平行度32 perpendicularity 垂直度直角度33 true position 位置度真位置度34 flatness 平面度平面度35 concentricity 同轴度同芯度36 roundness 真圆度真円度37 coplanarity 平坦度平坦度38 straightness 直线度真直度39 push-on, push-off 插拔力挿抜力40 insertion force 插入力挿入力41 extraction force 引拔力引き抜き力42 normal force 接触力接触力43 retention force 保持力保持力44 fitness 固着力固着力45 spring back 复员力复元力46 strength 强度强度47 actuating force 开关作用力スイッチ作动力48 solder wicking 焊锡度半田上がり49 flux raise 焊剂フラックス上がり50 conductivity 导通性导通性51 contact failure 接触不稳定接触不安定52 contact resistance 接触抵抗接触抵抗53 lighting 点灯点灯54 short circuit 短路短络55 burning 烧伤焼损56 dielectric 耐电压耐电圧57 insulation resistance 绝缘抵抗絶縁抵抗58 chip & scrap 切粉切粉59 scrap 废弃スクラップ60 die & tool mark 打痕ダイマーク61 crack 破裂割れ62 burrs 毛刺バリ63 flaw/scratch 伤/划伤伤／削れ64 inclusion 异物混入异物混入65 adhered substance 异物附着异物付着66 dirty 脏污污れ67 discoloration 变色変色68 discrepant color 不同颜色色违い69 coloring 颜色不均色调むら70 crushed 压坏溃れ71 breakage 破损破损72 bent, deformed 弯曲、变形曲がり、変形73 shape 形状形状74 rusty 锈锖75 marking 打印マーキング76 camber 反挠度キャンバー77 curly 卷取カール78 twist 扭转ねじれ79 excess adhered bond 接着剂过多接着剤过多80 chipping 缺损欠け81 plating thickness 镀层厚度メッキ厚82 porosity 砂眼ポロシティー（有孔性）83 peeling 剥离剥离84 solderability 焊锡附着性半田付き性85 not plated 露出底质地肤露出86 corrosion 腐蚀腐食87 discrepant plating 镀层不同メッキ违い88 tensil strength 拉力强度引张强度89 stiffness 耐力耐力90 hardness 硬度硬度91 extension 伸展伸び92 bend strength 折曲强度折り曲げ强さ93 short shot 注塑不足ショート・ショット94 weld line 熔接线ウェルド・ライン95 sink 逊色ひけ96 warp 弯度そり97 bubble 气泡気泡98 silver streak 银色シルバー99 whity 白化白化100 blistered 胀ふくれ99 whity 白化白化100 blistered 胀ふくれ101 chip 缺损欠け102 breakage 折断折れ103 cut 切断カット104 ejector mark 喷射标记エジェクター・マーク105 burnning 烧焼け106 core misassembly 组装错误组合わせ违い107 filled mold/excessive 型芯破损/多料コア破损/余肉108 dregs stopped 碎屑堆积カスつまり109 moisture ratio 水分率水分率110 torn 撕裂ちぎれ111 flow mark 波纹フローマーク112 compo parts short 缺少部品欠品113 actuation 动作作动114 install 安装取付115 adhesive 接着接着116 twisted 旋转度ツイスト117 color code 条形码カラー・コード118 brazing 焊接ろう付け（ブレージング）119 various defects 多种不良多种の不良120 poor insertion 插入不良挿入不良121 poor crimping 压着不良圧着不良122 poor termination 压接不良圧接不良123 poor thread 螺纹不良ねじ切り不良124 poor tapping 分接头不良タップ不良125 adjusting 调整调整126 material change 材料交换材料交换127 operator error 作业错误作业128 blacken 染黑黒染め129 poor coating 镀层不良メッキ不良130 heat treatment 热处理热处理131 missed finish 未加工未加工132 poor buff 光洁度不良バフ不良133 passivate 不导体处理不导体处理1 package, paper 包装箱，纸包装箱、纸2 label 标签ラベル3 letters 文字文字4 reel 卷轴リール5 tube 塑料管チューブ6 tray 托盘トレイ7 emboss[im'bɔ:s] tape 包装带エンボス・テープ8 blister pack 泡沫箱ブリスター・パック9 receptacle 雌（母）リセ10 socket 插座ソケット11 contact leaf 叶形リーフ12 plug插头プラグ13 tab扁形タブ14 pin 销形ピン15 post 导向柱形ポスト16 cantilever支承梁カンチ・レバー17 tine 尖端タイン18 bow 弓形ボウ19 rolling 旋转ローリング20 tongue 舌部トング（舌部）21 lance 矛形锁定ランス22 dimple ['dimpl]坑形锁定ディンプル23 emboss [im'bɔ:s]压模エンボス24 stopper 塞子ストッパー25 dimple hole 坑式洞ディンプル・ホール26 stabilizer ['steibilaizə]安定面スタビライザー27 action area 活动部アクション部28 shoulder 肩部ショルダー29 rib 肋リブ30 wire barrel['bærəl]金属线ワイヤ31 insulation [.insju'leiʃən] barrel 绝缘インシュレーション32 serration 非光滑面セレーション33 kick back 反冲キック・バック34 transition 转换部トランジション35 v slot v型狭孔ｖスロット36 barrel step 桶形级板バレル・ステップ37 bell mouth 喇叭口ベル・マウス38 splice 接头スプライス39 carrier 连桥部分キャリア40 carrier hole 连桥部孔キャリア・ホール41 slot 狭孔スロット42 cut off tab 切断剩余部カット・オフ・タブ43 i.d. mark 特殊标记ｉ．ｄ．マーク44 amp mark amp 标记ａｍｐマーク45 bead 突起部ビード46 seam 接缝シーム47 notch 刻痕ノッチ48 circuit cavity 回路孔回路キャビティ49 pitch 间距ピッチ50 circuit wall 隔离壁极间壁51 outer surface 外侧面外侧面52 edge 边缘エッジ53 gate 出入口ゲート54 card slot 卡缝カード・スロット55 post hole 导向柱孔ポスト穴56 circuit number 电路号码回路番号57 mold i.d. mark 模穴号标记キャビティ・マーク58 inner surface 内侧面内侧面59 mate area 嵌合侧はめあい部60 window 窗口窓61 flange area 凸缘部フランジ部62 hinge area 铰链部ヒンジ部63 housing lance 塑料件矛式锁定ハウジング・ランス64 sphincter 括约スフィンクター65 leg 脚、腿レグ66 wing 翅ウィング67 rib 肋リブ68 lance hole 矛式孔ランス穴69 polarization 极心ポラリゼーション70 bridge 桥ブリッジ71 indent 刻印インデント(雕り込み）72 detent 爪デテント73 ear 耳耳74 mounting hole 组装孔取付け穴75 board lock area 板锁定部ボード・ロック部76 housing 塑料件ハウジング77 contact 端子コンタクト78 shell 铁壳シェル79 solder peg 焊锡耳ソルダー・ペグ80 retention leg 保留腿リテンション・レグ81 tine plate 尖端板タイン・プレート82 g-plate 接地板ｇプレート83 guide post 导向柱ガイド・ポスト84 guide socket 导向插座ガイド・ソケット85 slider 滑动板スライダー86 contact forming 端子两次加工コンタクト二次加工87 pre-insertion 予插入仮挿入88 final insertion 正式插入本挿入89 carrier cut 连桥切断キャリア・カット90 bending 弯曲曲げ91 resizing 修整修正92 soldering 焊锡半田付け93 inspection 检查検査94 packing 包装捆包95 brass 黄铜黄铜96 pre-tin brass 镀锡黄铜锡メッキ黄铜97 phos-bronze 磷青铜りん青铜98 pre-tin phos-bronze 镀锡磷青铜锡メッキりん青铜99 be-cu 铍铜ベリ铜100 pre-tin be-cu 镀锡铍铜锡メッキベリ铜101 au, be-cu 镀金铍铜金メッキベリ铜102 copper 铜铜103 ca-725 ca-725 ｃａ－７２５104 stainless steel 不锈钢ステンレス・スティール105 klf-5 kif-5 ｋｌｆ－５106 tin lead 焊锡半田锡107 pre-tin klf-5 镀锡klf-5 锡メッキｋｌｆ－５108 super phos-bronze 超磷青铜超りん青铜109 msp-1 msp-1 ｍｓｐ－１110 mf202r mf202r ｍｆ２０２ｒ111 pre-tin-cu msp-1 镀锡铜msp-1 锡铜メッキｍｓｐ－１112 max-251 max251 ｍａｘ２５１（りん青铜）113 z-klf-5 z-klf-5 ｚ－ｋｌｆ－５114 pre-tin z-klf-5 镀锡z-kif-5 锡メッキｚ－ｋｌｆ－５115 fpc fpc ｆｐｃ116 pcb(pc board) pc板ｐｃボード（プリント基板）117 nylon 尼龙ナイロン118 noryl ノリル119 pbt pbt ｐｂｔ120 dap dap ｄａｐ121 phenol 苯酚フェノール122 lcp lcp ｌｃｐpunch, press冲punching machine 冲床hydraulic machine油压机jack升降机decoiler整平机manufacture management制造管理stamping, press冲压feeder送料机rack, shelf, stack料架taker取料机to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped报废scrape ..v.刮;削robot机械手production line流水线packaging tool打包机packaging打包well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口runner less无浇道sprue less 无射料管方式long nozzle延长喷嘴方式spur浇口;溶waste废料board广告牌sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理组装类assembly line组装线layout布置图conveyer流水线运\输带rivet machine拉钉机rivet gun拉钉枪screw driver起子electric screw driver电动起子hydraulic machine 液压机pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氩焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运\ be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine/heat stake热熔机/热风枪processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机品质类qualified products, up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part来件不良exposed metal/bare metal金属裸露excessive defect过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格cosmetic defect外观不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑丝missing part漏件wrong part错件oxidation氧化defective threading抽芽不良poor staking铆合不良deficient purchase来料不良deficient manufacturing procedure制程不良cosmetic inspection外观检查inner parts inspection内部检查blister 气泡angular offset 角度偏差dent 压痕scratch 刮伤deformation 变形filings 铁削defective label 不良标签abrasion 磨损breaking. (be)broken,(be)cracked 断裂short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delaminating起鳞speckle斑点mildewed =moldy = mouldy发霉burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质shrinking/shrinkage缩水mixed color杂色fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍impurity 杂质mismatch 错位failure, trouble 故障deformation 变形rust 生锈peel 脱漆shrink 缩水contamination 脏污water spots 水渍gap 间隙label error 标签错误missing label 漏贴rejection criteria 拒收标准suspected rejects 可疑庇abrasion 损伤、磨损texture surface 印花纹表面streak 条纹stains 污点blotch 斑点discoloration 脱色inclusion 杂质slug mark 压痕dirt grime 灰尘blush 毛边薄膜sink 下凹hickey 漏漆labels and logos 贴纸与商标configuration labels 组合贴纸corrugated container 瓦摆纸箱delaminating 脱层splattering 散点gouge 锉孔puckering 折痕通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |\'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位human resources department人力资源部head count 人头数production department生产部门planning department企划部qc section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日color management 颜色管理visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量physical count quantity帐面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 电脑外壳(组件)personal computer enclosure 电脑机箱产品front plate前板rear plate后板chassis |\'∫鎠i| 基座bezel panel面板hood 上盖base pan 基座bezel 面板riser card 扩充卡flat cable 排线top driver cage 上磁架bottom driver cage 下磁架resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑胶件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程表单production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套band-aid创可贴industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机club car高尔夫球车plate电镀power button电源按键reset button重置键forklift叉车workshop traveler 天车trailer =long vehicle拖板车hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate座标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉伸work cell/work shop工作间sub-line支线bottleneck 瓶颈模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模stage die工程模compound die复合模shearing die剪边模riveting die铆合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 换模to fix a die装模to repair a die修模punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)upper supporting blank上承板upper padding plate blank上垫板top plate上托板（顶板）top block上垫脚stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块die locker锁模器pressure plate =plate pinch压板thickness gauge厚薄规cutting die, blanking die冲裁模die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条panel board镶块to load a die装上模具to unload a die 御模具active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块pilot导正筒trim剪外边pierce剪内边pocket for the punch head挂钩槽slug hole废料孔radius半径shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺丝form block折刀round pierce punch =die button圆冲子shape punch =die insert异形子stock located block定位块metal plate钣金miller铣床grinder磨床tolerance公差score =groove压线sliding block滑块lathe车active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板capability能力parameter参数factor系数driller钻床set up die架模height of die setting up架模高度analog-mode device类模器inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves =spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套press specification冲床规格die height闭模高度flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝stripper plate脱料板piston活塞handle mold手持式模具flash mold溢流式模具positive mold挤压式模具split mold分割式模具die lifter举模器top stop上死点bottom stop下死点one stroke一行程to continue, cont.连动to grip(material)吸料location lump, locating piece, location block定位块reset复位to file burr 锉毛刺embedded lump |in\'bed| |l赞p|镶块stamping-missing漏冲to tight a bolt拧紧螺栓to loosen a bolt拧松螺栓punched hole冲孔to cut edge =side cut =side scrap 切边to bending折弯to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake铆合designing, to design设计design modification 设计修改成gauge(or jig)治具pedal踩踏板stopper阻挡器flow board流水板torque扭矩spline =the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的forming成型(抽凸,冲凸)draw hole抽孔emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线stamp letter冲字(料号)tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图connecter 连接器cable 导线wire-to-wire 线至线wire-to-board 线至板mini-universal 小型通用circular plastic connectors 塑料密封环连接器dl (dual-leaf) contact sockets 双叶式触点插座drawn spring dip contact socket 弹簧触点插座zig-zag package sockets 锯齿形封装插座positive lock connectors 确立锁定连接器coax mix 同轴混合shielded circular din connectors 屏蔽式圆型din连接器memory card connectors 记忆装置插结连接器simm sockets 单列记忆模件插座low profile 低高度cis (commercial interconnection system) 商用连接系统hinge connectors 铰连连接器card-edge connectors 边缘插接连接器euro card connectors 欧式插接连接器modular interconnection system 组合连接系统interconnection system 互连系统rf connectors 射频连接器twin-ax connectors 双轴互连系统low profile coaxial tap 低高度型有源同轴电缆线器4 position data connectors 4位数据连接器insulation and wire support 绝缘体及导线套ring-tongue terminals 环形舌端子wire size range 线径范围slotted-tongue terminals 叉式舌片端子butt splices 对头接头dentented ring-tongue terminals 卡爪环舌型端子fits tab thickness 配合接片厚度accepts terminals 配合端子crimp-type tabs 压接式接片free-hanging and panel-mount applications 自由悬挂及面板装嵌适用cable clamp 电缆钳位夹pc board vertical pin headers 垂直接插式接插头组件pc board right-angle pin and socket headers 水平接插式接插头组件panel-mount connectors 面板装嵌连接器insulation displacement plugs 绝缘位移连接插头dielectric withstanding voltage 介质承受电压free-hanging type cap housings 自由悬挂式套座壳体semiautomatic crimping machine 半自动压接机power supply 供给功率air pir pressure 气压panel mount type cap housings 面板装嵌套座壳体post header for printed circuit board 印刷底板用柱头mass termination assemblies 集体端接组件post header assemblies 接插柱头组件polarized right angle post header assembly 有极向性水平接插柱头组件friction lock 锁尖装置sigle leaf connectors 单叶片连接器cpc (circular plastic connectors) 塑料密封环型连接器ceimp snap-in contacts 压接式套入触点socket with straight solder tails 直立焊脚插座retention feature solder tails 弯曲焊脚sockets with retention feature solder tails 面板附定曲脚插座high pressure tin (hpt) sockets 镀锡高压芯片positive lock retention feature 彻底锁定装置plug-grounding indents 插头外罩接地凹位solder cup connector 焊杯触点连接器straight exit rfi/emi shield for jacketed cable 直线引出rfi/emi 屏蔽外壳外套导线束适用backshell assembly 后部外壳组件board-mount connectors with threaded inserts and board locks 底板安装连接器附内丝牙及板扣board-mount receptacles 底板安装插座non-polarized receptacles 无定位型插座handset plug assembly 电话线插头组件line cord plug assembly 听筒插头组件1、表面间连接：interlayer connection2、层间连接：interlayer connection3、内层连接：innerlayer connection4、非菜单面连接：nonfunctional interfacial connection5、跨接线：jumper wire6、节(交)点：node7、附加线：haywire8、端接(点)：terminal9、连接线：terminated line10、端接：termination11、连接端：pad, land12、贯穿连接：through connection13、支线：stub14、印制插头：tab15、键槽：keying slot16、连接器：connector17、板边连接器：edge board connector18、连接器区：connector area19、直角板边连接器：right angle edge connector20、偏槽口：polarizing slot21、偏置端接区：offset terminal area22、接地：ground23、端接隔离(空环)：terminal clearance24、连通性：continuity25、连接器接触：connector contact26、接触面积：contact area27、接触间距：contact spacing28、接触电阻：contact resistance29、接触尺寸：contact size30、组件引腿(脚)：component lead31、组件插针：component pin32、最小电气间距：minimum electrical spacing33、导电性：conductivity34、边卡连接器：card-edge connector35、插卡连接器：card-insertion connector36、载流量：current-carrying capacity37、蹯径：path38、最短路径：shortest path39、关键路径：critical path40、倒角：miter41、串推：daisy chain42、斯坦纳树：steiner tree43、最小生成树：minimum spanning tree (mst)44、瓶颈宽度：necked width45、短叉长度：spur length46、短柱长度：stub length47、曼哈顿路径：manhattan path48、连接度(性)：connectivity。
连接器中英文常用语
连接器用语集(质量）中英日1 other part no. 不同现品现品相违2 other material 不同材料材料相违3 quantity shortage 数量不足数量不足4 mixed 异种混入异种混入5 broken 破损破损6 discrepant 不同相违7 illegible letters 文字不清晰文字不鲜明8 missing indication 忘记表示表示忘れ9 approval mark uua，csa标识 uua、csa表示10 inspection sheet 成绩书成绩书11 poor reeling 卷取不良巻き不良12 tangled 缠からみ13 reversed 卷反逆巻き14 defected splice 继续継ぎ15 back reel 往里卷里巻き16 direction off top 取出方法取り出し方法17 gap 上下距离ギャップ18 height,depth 高度，深度高さ、深さ19 location 位置位置20 width 宽度幅21 thickness 厚度厚さ22 outer diameter 外径外形（外寸）23 inner diameter 内径内径（内寸）24 angle 角度角度25 pitch 中心间距离ピッチ26 swage, chamfer 倒角面取り27 diagonal 对角尺寸対角寸法28 diameter 直径直径29 length 长度长さ30 symmetry 对称度対称度31 parallelism 平行度平行度32 perpendicularity 垂直度直角度33 true position 位置度真位置度34 flatness 平面度平面度35 concentricity 同轴度同芯度36 roundness 真圆度真円度37 coplanarity 平坦度平坦度38 straightness 直线度真直度39 push-on, push-off 插拔力挿抜力40 insertion force 插入力挿入力41 extraction force 引拔力引き抜き力42 normal force 接触力接触力43 retention force 保持力保持力44 fitness 固着力固着力45 spring back 复员力复元力46 strength 强度强度47 actuating force 开关作用力スイッチ作动力48 solder wicking 焊锡度半田上がり49 flux raise 焊剂フラックス上がり50 conductivity 导通性导通性51 contact failure 接触不稳定接触不安定52 contact resistance 接触抵抗接触抵抗53 lighting 点灯点灯54 short circuit 短路短络55 burning 烧伤焼损56 dielectric 耐电压耐电圧57 insulation resistance 绝缘抵抗絶縁抵抗58 chip & scrap 切粉切粉59 scrap 废弃スクラップ60 die & tool mark 打痕ダイマーク61 crack 破裂割れ62 burrs 毛刺バリ63 flaw/scratch 伤/划伤伤／削れ64 inclusion 异物混入异物混入65 adhered substance 异物附着异物付着66 dirty 脏污污れ67 discoloration 变色変色68 discrepant color 不同颜色色违い69 coloring 颜色不均色调むら70 crushed 压坏溃れ71 breakage 破损破损72 bent, deformed 弯曲、变形曲がり、変形73 shape 形状形状74 rusty 锈锖75 marking 打印マーキング76 camber 反挠度キャンバー77 curly 卷取カール78 twist 扭转ねじれ79 excess adhered bond 接着剂过多接着剤过多80 chipping 缺损欠け81 plating thickness 镀层厚度メッキ厚82 porosity 砂眼ポロシティー（有孔性）83 peeling 剥离剥离84 solderability 焊锡附着性半田付き性85 not plated 露出底质地肤露出86 corrosion 腐蚀腐食87 discrepant plating 镀层不同メッキ违い88 tensil strength 拉力强度引张强度89 stiffness 耐力耐力90 hardness 硬度硬度91 extension 伸展伸び92 bend strength 折曲强度折り曲げ强さ93 short shot 注塑不足ショート・ショット94 weld line 熔接线ウェルド・ライン95 sink 逊色ひけ96 warp 弯度そり97 bubble 气泡気泡98 silver streak 银色シルバー99 whity 白化白化100 blistered 胀ふくれ99 whity 白化白化100 blistered 胀ふくれ101 chip 缺损欠け102 breakage 折断折れ103 cut 切断カット104 ejector mark 喷射标记エジェクター・マーク105 burnning 烧焼け106 core misassembly 组装错误组合わせ违い107 filled mold/excessive 型芯破损/多料コア破损/余肉108 dregs stopped 碎屑堆积カスつまり109 moisture ratio 水分率水分率110 torn 撕裂ちぎれ111 flow mark 波纹フローマーク112 compo parts short 缺少部品欠品113 actuation 动作作动114 install 安装取付115 adhesive 接着接着116 twisted 旋转度ツイスト117 color code 条形码カラー・コード118 brazing 焊接ろう付け（ブレージング）119 various defects 多种不良多种の不良120 poor insertion 插入不良挿入不良121 poor crimping 压着不良圧着不良122 poor termination 压接不良圧接不良123 poor thread 螺纹不良ねじ切り不良124 poor tapping 分接头不良タップ不良125 adjusting 调整调整126 material change 材料交换材料交换127 operator error 作业错误作业128 blacken 染黑黒染め129 poor coating 镀层不良メッキ不良130 heat treatment 热处理热处理131 missed finish 未加工未加工132 poor buff 光洁度不良バフ不良133 passivate 不导体处理不导体处理1 package, paper 包装箱，纸包装箱、纸2 label 标签ラベル3 letters 文字文字4 reel 卷轴リール5 tube 塑料管チューブ6 tray 托盘トレイ7 emboss[im'bɔ:s] tape 包装带エンボス・テープ8 blister pack 泡沫箱ブリスター・パック9 receptacle 雌（母）リセ10 socket 插座ソケット11 contact leaf 叶形リーフ12 plug插头プラグ13 tab扁形タブ14 pin 销形ピン15 post 导向柱形ポスト16 cantilever支承梁カンチ・レバー17 tine 尖端タイン18 bow 弓形ボウ19 rolling 旋转ローリング20 tongue 舌部トング（舌部）21 lance 矛形锁定ランス22 dimple ['dimpl]坑形锁定ディンプル23 emboss [im'bɔ:s]压模エンボス24 stopper 塞子ストッパー25 dimple hole 坑式洞ディンプル・ホール26 stabilizer ['steibilaizə]安定面スタビライザー27 action area 活动部アクション部28 shoulder 肩部ショルダー29 rib 肋リブ30 wire barrel['bærəl]金属线ワイヤ31 insulation [.insju'leiʃən] barrel 绝缘インシュレーション32 serration 非光滑面セレーション33 kick back 反冲キック・バック34 transition 转换部トランジション35 v slot v型狭孔ｖスロット36 barrel step 桶形级板バレル・ステップ37 bell mouth 喇叭口ベル・マウス38 splice 接头スプライス39 carrier 连桥部分キャリア40 carrier hole 连桥部孔キャリア・ホール41 slot 狭孔スロット42 cut off tab 切断剩余部カット・オフ・タブ43 i.d. mark 特殊标记ｉ．ｄ．マーク44 amp mark amp 标记ａｍｐマーク45 bead 突起部ビード46 seam 接缝シーム47 notch 刻痕ノッチ48 circuit cavity 回路孔回路キャビティ49 pitch 间距ピッチ50 circuit wall 隔离壁极间壁51 outer surface 外侧面外侧面52 edge 边缘エッジ53 gate 出入口ゲート54 card slot 卡缝カード・スロット55 post hole 导向柱孔ポスト穴56 circuit number 电路号码回路番号57 mold i.d. mark 模穴号标记キャビティ・マーク58 inner surface 内侧面内侧面59 mate area 嵌合侧はめあい部60 window 窗口窓61 flange area 凸缘部フランジ部62 hinge area 铰链部ヒンジ部63 housing lance 塑料件矛式锁定ハウジング・ランス64 sphincter 括约スフィンクター65 leg 脚、腿レグ66 wing 翅ウィング67 rib 肋リブ68 lance hole 矛式孔ランス穴69 polarization 极心ポラリゼーション70 bridge 桥ブリッジ71 indent 刻印インデント(雕り込み）72 detent 爪デテント73 ear 耳耳74 mounting hole 组装孔取付け穴75 board lock area 板锁定部ボード・ロック部76 housing 塑料件ハウジング77 contact 端子コンタクト78 shell 铁壳シェル79 solder peg 焊锡耳ソルダー・ペグ80 retention leg 保留腿リテンション・レグ81 tine plate 尖端板タイン・プレート82 g-plate 接地板ｇプレート83 guide post 导向柱ガイド・ポスト84 guide socket 导向插座ガイド・ソケット85 slider 滑动板スライダー86 contact forming 端子两次加工コンタクト二次加工87 pre-insertion 予插入仮挿入88 final insertion 正式插入本挿入89 carrier cut 连桥切断キャリア・カット90 bending 弯曲曲げ91 resizing 修整修正92 soldering 焊锡半田付け93 inspection 检查検査94 packing 包装捆包95 brass 黄铜黄铜96 pre-tin brass 镀锡黄铜锡メッキ黄铜97 phos-bronze 磷青铜りん青铜98 pre-tin phos-bronze 镀锡磷青铜锡メッキりん青铜99 be-cu 铍铜ベリ铜100 pre-tin be-cu 镀锡铍铜锡メッキベリ铜101 au, be-cu 镀金铍铜金メッキベリ铜102 copper 铜铜103 ca-725 ca-725 ｃａ－７２５104 stainless steel 不锈钢ステンレス・スティール105 klf-5 kif-5 ｋｌｆ－５106 tin lead 焊锡半田锡107 pre-tin klf-5 镀锡klf-5 锡メッキｋｌｆ－５108 super phos-bronze 超磷青铜超りん青铜109 msp-1 msp-1 ｍｓｐ－１110 mf202r mf202r ｍｆ２０２ｒ111 pre-tin-cu msp-1 镀锡铜msp-1 锡铜メッキｍｓｐ－１112 max-251 max251 ｍａｘ２５１（りん青铜）113 z-klf-5 z-klf-5 ｚ－ｋｌｆ－５114 pre-tin z-klf-5 镀锡z-kif-5 锡メッキｚ－ｋｌｆ－５115 fpc fpc ｆｐｃ116 pcb(pc board) pc板ｐｃボード（プリント基板）117 nylon 尼龙ナイロン118 noryl ノリル119 pbt pbt ｐｂｔ120 dap dap ｄａｐ121 phenol 苯酚フェノール122 lcp lcp ｌｃｐpunch, press冲punching machine 冲床hydraulic machine油压机jack升降机decoiler整平机manufacture management制造管理stamping, press冲压feeder送料机rack, shelf, stack料架taker取料机to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped报废scrape ..v.刮;削robot机械手production line流水线packaging tool打包机packaging打包well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口runner less无浇道sprue less 无射料管方式long nozzle延长喷嘴方式spur浇口;溶waste废料board广告牌sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理组装类assembly line组装线layout布置图conveyer流水线运\输带rivet machine拉钉机rivet gun拉钉枪screw driver起子electric screw driver电动起子hydraulic machine 液压机pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氩焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运\ be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine/heat stake热熔机/热风枪processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机品质类qualified products, up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part来件不良exposed metal/bare metal金属裸露excessive defect过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格cosmetic defect外观不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑丝missing part漏件wrong part错件oxidation氧化defective threading抽芽不良poor staking铆合不良deficient purchase来料不良deficient manufacturing procedure制程不良cosmetic inspection外观检查inner parts inspection内部检查blister 气泡angular offset 角度偏差dent 压痕scratch 刮伤deformation 变形filings 铁削defective label 不良标签abrasion 磨损breaking. (be)broken,(be)cracked 断裂short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delaminating起鳞speckle斑点mildewed =moldy = mouldy发霉burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质shrinking/shrinkage缩水mixed color杂色fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍impurity 杂质mismatch 错位failure, trouble 故障deformation 变形rust 生锈peel 脱漆shrink 缩水contamination 脏污water spots 水渍gap 间隙label error 标签错误missing label 漏贴rejection criteria 拒收标准suspected rejects 可疑庇abrasion 损伤、磨损texture surface 印花纹表面streak 条纹stains 污点blotch 斑点discoloration 脱色inclusion 杂质slug mark 压痕dirt grime 灰尘blush 毛边薄膜sink 下凹hickey 漏漆labels and logos 贴纸与商标configuration labels 组合贴纸corrugated container 瓦摆纸箱delaminating 脱层splattering 散点gouge 锉孔puckering 折痕通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |\'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位human resources department人力资源部head count 人头数production department生产部门planning department企划部qc section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日color management 颜色管理visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量physical count quantity帐面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 电脑外壳(组件)personal computer enclosure 电脑机箱产品front plate前板rear plate后板chassis |\'∫鎠i| 基座bezel panel面板hood 上盖base pan 基座bezel 面板riser card 扩充卡flat cable 排线top driver cage 上磁架bottom driver cage 下磁架resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑胶件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程表单production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套band-aid创可贴industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机club car高尔夫球车plate电镀power button电源按键reset button重置键forklift叉车workshop traveler 天车trailer =long vehicle拖板车hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate座标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉伸work cell/work shop工作间sub-line支线bottleneck 瓶颈模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模stage die工程模compound die复合模shearing die剪边模riveting die铆合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 换模to fix a die装模to repair a die修模punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)upper supporting blank上承板upper padding plate blank上垫板top plate上托板（顶板）top block上垫脚stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块die locker锁模器pressure plate =plate pinch压板thickness gauge厚薄规cutting die, blanking die冲裁模die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条panel board镶块to load a die装上模具to unload a die 御模具active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块pilot导正筒trim剪外边pierce剪内边pocket for the punch head挂钩槽slug hole废料孔radius半径shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺丝form block折刀round pierce punch =die button圆冲子shape punch =die insert异形子stock located block定位块metal plate钣金miller铣床grinder磨床tolerance公差score =groove压线sliding block滑块lathe车active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板capability能力parameter参数factor系数driller钻床set up die架模height of die setting up架模高度analog-mode device类模器inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves =spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套press specification冲床规格die height闭模高度flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝stripper plate脱料板piston活塞handle mold手持式模具flash mold溢流式模具positive mold挤压式模具split mold分割式模具die lifter举模器top stop上死点bottom stop下死点one stroke一行程to continue, cont.连动to grip(material)吸料location lump, locating piece, location block定位块reset复位to file burr 锉毛刺embedded lump |in\'bed| |l赞p|镶块stamping-missing漏冲to tight a bolt拧紧螺栓to loosen a bolt拧松螺栓punched hole冲孔to cut edge =side cut =side scrap 切边to bending折弯to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake铆合designing, to design设计design modification 设计修改成gauge(or jig)治具pedal踩踏板stopper阻挡器flow board流水板torque扭矩spline =the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的forming成型(抽凸,冲凸)draw hole抽孔emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线stamp letter冲字(料号)tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图connecter 连接器cable 导线wire-to-wire 线至线wire-to-board 线至板mini-universal 小型通用circular plastic connectors 塑料密封环连接器dl (dual-leaf) contact sockets 双叶式触点插座drawn spring dip contact socket 弹簧触点插座zig-zag package sockets 锯齿形封装插座positive lock connectors 确立锁定连接器coax mix 同轴混合shielded circular din connectors 屏蔽式圆型din连接器memory card connectors 记忆装置插结连接器simm sockets 单列记忆模件插座low profile 低高度cis (commercial interconnection system) 商用连接系统hinge connectors 铰连连接器card-edge connectors 边缘插接连接器euro card connectors 欧式插接连接器modular interconnection system 组合连接系统interconnection system 互连系统rf connectors 射频连接器twin-ax connectors 双轴互连系统low profile coaxial tap 低高度型有源同轴电缆线器4 position data connectors 4位数据连接器insulation and wire support 绝缘体及导线套ring-tongue terminals 环形舌端子wire size range 线径范围slotted-tongue terminals 叉式舌片端子butt splices 对头接头dentented ring-tongue terminals 卡爪环舌型端子fits tab thickness 配合接片厚度accepts terminals 配合端子crimp-type tabs 压接式接片free-hanging and panel-mount applications 自由悬挂及面板装嵌适用cable clamp 电缆钳位夹pc board vertical pin headers 垂直接插式接插头组件pc board right-angle pin and socket headers 水平接插式接插头组件panel-mount connectors 面板装嵌连接器insulation displacement plugs 绝缘位移连接插头dielectric withstanding voltage 介质承受电压free-hanging type cap housings 自由悬挂式套座壳体semiautomatic crimping machine 半自动压接机power supply 供给功率air pir pressure 气压panel mount type cap housings 面板装嵌套座壳体post header for printed circuit board 印刷底板用柱头mass termination assemblies 集体端接组件post header assemblies 接插柱头组件polarized right angle post header assembly 有极向性水平接插柱头组件friction lock 锁尖装置sigle leaf connectors 单叶片连接器cpc (circular plastic connectors) 塑料密封环型连接器ceimp snap-in contacts 压接式套入触点socket with straight solder tails 直立焊脚插座retention feature solder tails 弯曲焊脚sockets with retention feature solder tails 面板附定曲脚插座high pressure tin (hpt) sockets 镀锡高压芯片positive lock retention feature 彻底锁定装置plug-grounding indents 插头外罩接地凹位solder cup connector 焊杯触点连接器straight exit rfi/emi shield for jacketed cable 直线引出rfi/emi 屏蔽外壳外套导线束适用backshell assembly 后部外壳组件board-mount connectors with threaded inserts and board locks 底板安装连接器附内丝牙及板扣board-mount receptacles 底板安装插座non-polarized receptacles 无定位型插座handset plug assembly 电话线插头组件line cord plug assembly 听筒插头组件1、表面间连接：interlayer connection2、层间连接：interlayer connection3、内层连接：innerlayer connection4、非菜单面连接：nonfunctional interfacial connection5、跨接线：jumper wire6、节(交)点：node7、附加线：haywire8、端接(点)：terminal9、连接线：terminated line10、端接：termination11、连接端：pad, land12、贯穿连接：through connection13、支线：stub14、印制插头：tab15、键槽：keying slot16、连接器：connector17、板边连接器：edge board connector18、连接器区：connector area19、直角板边连接器：right angle edge connector20、偏槽口：polarizing slot21、偏置端接区：offset terminal area22、接地：ground23、端接隔离(空环)：terminal clearance24、连通性：continuity25、连接器接触：connector contact26、接触面积：contact area27、接触间距：contact spacing28、接触电阻：contact resistance29、接触尺寸：contact size30、组件引腿(脚)：component lead31、组件插针：component pin32、最小电气间距：minimum electrical spacing33、导电性：conductivity34、边卡连接器：card-edge connector35、插卡连接器：card-insertion connector36、载流量：current-carrying capacity37、蹯径：path38、最短路径：shortest path39、关键路径：critical path40、倒角：miter41、串推：daisy chain42、斯坦纳树：steiner tree43、最小生成树：minimum spanning tree (mst)44、瓶颈宽度：necked width45、短叉长度：spur length46、短柱长度：stub length47、曼哈顿路径：manhattan path48、连接度(性)：connectivity。
工业连接器中英对照
·use screwdriver to disassemble, torque is 0.6N·m
·applicable to wave Soldering, load can reach 13.5A
·environmental-friendly products(meet the requirement of RoHS)
·applicable to wave Soldering, load can reach 17.5A
·environmental-friendly products(meet the requirement of RoHS)
2.HFLS1A-508/MAXX
Fixed terminal block
striping length拨线长度
tightening torque螺钉扭力矩
Insulation material type/Insulation materialgroup绝缘材料类型/绝缘材料组
ordering data订货数据
type型号
poles极数
Pcs/box件/包
1.HFLS1A-500
·applicable to wave Soldering, load can reach 24A
·environmental-friendly products(meet the requirement of RoHS)
19.HFLS1B10-350
插拨式接线端子
Features
PCB terminal block, using non-screw connector with push button
连接器行业专业英语高频词句
连接器行业专业英语高频词句（中英对照）Connecter 连接器Cable 导线Wire-to-wire 线至线Wire-to-board 线至板Mini-universal 小型通用Circular plastic connectors 塑料密封环连接器DL (dual-leaf) contact sockets 双叶式触点插座Drawn spring DIP contact socket 弹簧触点插座Zig-zag package sockets 锯齿形封装插座Positive lock connectors 确立锁定连接器Coax mix 同轴混合Shielded circular DIN connectors 屏蔽式圆型DIN连接器Memory card connectors 记忆装置插结连接器SIMM sockets 单列记忆模件插座Low profile 低高度CIS (commercial interconnection system) 商用连接系统Hinge connectors 铰连连接器Card-edge connectors 边缘插接连接器Euro card connectors 欧式插接连接器Modular interconnection system 组合连接系统interconnection system 互连系统RF connectors 射频连接器Twin-Ax connectors 双轴互连系统Low profile coaxial tap 低高度型有源同轴电缆线器4 position data connectors 4位数据连接器Insulation and wire support 绝缘体及导线套Ring-Tongue terminals 环形舌端子Wire size range 线径范围Slotted-Tongue terminals 叉式舌片端子Butt splices 对头接头Dentented Ring-Tongue terminals 卡爪环舌型端子Fits tab thickness 配合接片厚度Accepts terminals 配合端子Crimp-type tabs 压接式接片Free-Hanging and Panel-Mount Applications 自由悬挂及面板装嵌适用Cable clamp 电缆钳位夹PC Board vertical pin headers 垂直接插式接插头组件PC Board Right-Angle pin and socket headers 水平接插式接插头组件Panel-Mount connectors 面板装嵌连接器Insulation Displacement plugs 绝缘位移连接插头Dielectric withstanding voltage 介质承受电压Free-Hanging type cap housings 自由悬挂式套座壳体Semiautomatic crimping machine 半自动压接机Power supply 供给功率Air pir pressure 气压Panel mount type cap housings 面板装嵌套座壳体Post header for printed circuit board 印刷底板用柱头Mass termination assemblies 集体端接组件Post header assemblies 接插柱头组件Polarized right angle post header assembly 有极向性水平接插柱头组件Friction lock 锁尖装置Sigle leaf connectors 单叶片连接器CPC (circular plastic connectors) 塑料密封环型连接器Crimp Snap-In contacts 压接式套入触点Socket with straight solder tails 直立焊脚插座Retention feature solder tails 弯曲焊脚Sockets with retention feature solder tails 面板附定曲脚插座2High Pressure Tin (HPT) sockets 镀锡高压芯片Positive lock retention feature 彻底锁定装置Plug-Grounding Indents 插头外罩接地凹位Solder Cup connector 焊杯触点连接器Straight Exit RFI/EMI shield for Jacketed cable 直线引出RFI/EMI屏蔽外壳外套导线束适用Backshell assembly 后部外壳组件Board-Mount connectors with threaded inserts and board locks 底板安装连接器附内丝牙及板扣Board-Mount Receptacles 底板安装插座Non-Polarized Receptacles 无定位型插座Handset plug assembly 电话线插头组件Line cord plug assembly 听筒插头组件射频同轴连接器RF coaxial connector1.按尺寸分类 Connector types by size●标准连接器standard connector●小型连接器miniature connector●微型连接器sub-miniature connector●超小型连接器micro-miniature connector2. 结构和安装类型 Connector configurations & mounting styles2.1接电缆的连接器 Cabled connector●直式 straight●弯式 right angle （直角）●穿墙式 bulkhead n. 隔壁,防水壁,分壁2.2不接电缆的连接器 Uncabled connector●PC板安装 PC mount●表面贴装 surface mount●边缘安装（偏腿）end launch●法兰安装 flange mount3. 联接机构 Coupling mechanism●螺纹联接 threaded connection（e.g. SMA）●卡口式联接 bayonet coupling（e.g. BNC）●推入式联接 snap-on coupling（e.g. MMCX）●快速锁紧联接 quick-lock coupling（e.g. QMA）●滑入式联接 slide-on coupling （e.g. BMA）4. 组成部件 Parts●壳体 body/shell/housing●绝缘子 insulator●夹头绝缘子 clamp top insulator●中心接触件 center contactａ．插针 male/pinｂ．插孔 female/jack●中心导体 center conductor●内导体 inner conductor●外导体 outer conductor●插座/插口 jack-panel jack 面板插口/插座-bulkhead jack 穿墙插座4●插头 receptacle5. 材料 Material●黄铜 copper●铍青铜 beryllium copper●锡磷青铜 phosphor bronze●聚四氟乙烯 PTFE polytetrafluoroethylene 特氟纶teflon ●不锈钢 stainless steel●合金 alloy●实心聚乙烯 solid PE●泡沫聚乙烯 foam PE /cellular polyethylene●白铜 white bronze●硅橡胶 silicon rubber●裸铜 BC=bare copper●易切削黄铜free cutting brass●稀土磁铁rare earth magnet●铝箔 aluminium foil●基材 base material●FR-4板材 FR-4 plate●硅脂 silicon grease●润滑硅脂 lubricating silicone grease6. 电镀 Plating/finishing●镀金 gold plated●镀镍 nickel plated●钝化 passivated●镀三元合金 SUCO plating●镍磷合金（无磁镍）镀层 SUCOPRO●铜，锡，锌镀层 copper-tin-zinc plating●滚镀 barrel plating●合金电镀 alloy plating7. 电气特性 Electrical characteristics●阻抗(欧姆) impedance （ohms）ａ．特性阻抗 characteristic impedanceｂ．标称阻抗 nominal impedance●频率范围 frequency range●工作频率 operating frequency●工作电压 working volt●额定电压 voltage rating●介质耐压 DWV=dielectric withstanding voltage (如:最大/小有效值为ａ伏 e.g. ａＶｒｍｓ．ｍａｘ／ｍｉｎ）●海平面耐电压：proof voltage at sea level●射频泄露 RF leakage●绝缘电阻 insulation resistance●插入损耗 insertion loss●电压驻波比 VSWR6●额定热电流 rated thermal current●介电常数 dielectric constant●击穿电压 breakdown voltage●额定电流 current rating●电容 capacitance●电感 inductance●电晕损耗 corona loss●熄灭电压 extinction voltage●屏蔽效应 shielding efficiency●低损耗 low loss8. 机械特性Mechanical characteristics●耐久性（次数）durability/mating life（cycles）●电缆保持力 cable retention force●啮合力 engagement force●分离力 separation force/ disengagement●轴向力 axial force ( insertion & withdrawal 插入&抽出力) ●扭矩 torque●径向扭矩力 radial torque●弯曲力矩 bending moment●弯曲半径 bending radius●抗张强度 tensile strength●机械应力 mechanical stress●机械互换性：mechanical compatibility●中心接触件固定性 center contact captivation●制动 cathers mit9. 环境性能及试验Environmental characteristics & test●工作温度范围 operating temperature range●贮存温度 storage temperature●密封，透气/不透气 sealing，hermetic/non-hermetic●防潮 moistureproof/ dampproof●耐湿 humidity resistance●防水 waterproof●耐高温 high temperature resistance●耐热性 heat resistance●抗腐蚀性 corrrosion resistance●阻燃 flame resistant●抗风化，耐风雨，不受气候影响的 weather proof●热冲击 thermal shock●冲击 shock●振动 vibration●稳态湿热 damp heat, steady state●恒温 costant temperature●大气压（力），气压 barometric pressure●热处理，低温退火 annealing8●盐雾试验 salt mist/spray test●高压绝缘试验,闪点试验,火花试验 flash test●破坏性试验 destructive test●气密性试验 air tightness test●放电试验 discharge test10. 附件 Accessory●线夹 crimp ferrule●垫片 gasket●热缩管 heat shrink tubing/ heat-shrinkable tubing ●护线套 barrel crimp●衬套 bushing/braid clamp●卡环 lock ring/ snap ring●卡圈/弹簧卡环/压紧圈/挡圈 retainer ring●卡圈 collar●限位环 spacing ring/ stop collar●防晃圈 anti-rock ring●弹性接触件 resilient contact●锁销 lockpin●锁紧垫圈 lock washer●弹簧/性垫圈 spring washer●密封圈 seal ring●开口垫圈 slotted washer●防尘帽 dustproof cover/ dust cap●螺母 nut/screw nut●螺纹套筒 threaded sleeve●滚花螺母 knurled nut●直纹滚花 straight knurls●网纹滚花 crossed knurls●防松螺母/自锁螺母 locknut●锁紧螺母，止动螺母，压紧螺母 jam nut●紧固螺母 clamp nut●螺丝钉screw●法兰盘/凸缘盘 flange plate●橡胶圈 gum ring●纯胶管，软管 gum rubber tubing●连接套 barrel splice / joint sleeve●波导管 waveguide●弹簧夹 spring finger●弹簧片 spring lamination●紧固件 fixture/fastener●紧固螺栓 fastening bolt/ binding bolt●密封塞子 sealing plug●密封盖 sealing cover●匹配针 matched pin10●两芯电源插座 2-Core Socket●无源元件 passive component11. 工装夹具 Work fixture●夹具 clamping yoke●冲压工具 stamping tool●去毛刺工具 deburr tool●螺丝刀 screwdriver●平口螺丝刀 slotted screwdrier●十字花螺丝刀 phillips screwdrier●铆合机 staker / riveting machine ●翻边器/卷边器 hemmer/fold back tool ●钳子/镊子 pliers●螺丝钳/夹钳 clamp●电缆钳 cable nipper●剪钳，老虎钳 cutting nipper●尖嘴钳 sharp-nose pliers●钢丝剪钳 wire nipper●锉刀 file●扳手 wrench●钢锯 hacksaw●铆钉钳 rivet clipper●铆钉机 rivet driver●整平器，剔除器 flush trimmer●修边模 flush trim die●卡接槽口 clamping Slot●卡接工具 clamping cool●卡线钳 clamping pincers●力矩扳手 torque spanner●拧上 screw on●拧下 screw off射频同轴电缆及组件RF coaxial cable & cable assemblies1. 电缆类型 Cable types●超柔电缆 super-flexible cable●柔软电缆 flexible cable●半柔电缆 semi-flexible cable●半刚电缆 semi-rigid cable●跳/馈线 jumper/feeder cable●波纹电缆 corrugated cable2. 电缆组件类型 Cable assembly types●半刚电缆组件 semi-rigid cable assembly●半柔电缆组件 semi-flexible cable assembly●柔性电缆组件 flexible cable assembly●低损耗、稳相电缆组件 low loss & stable phase cable assembly12●毫米波电缆组件 millimeter wave cable assembly3.电缆设计Cable design3.1外导体设计 Design of outer conductor●单屏蔽 single screen●双屏蔽 double screen●绕包带和屏蔽层 tape and screen●金属管（半刚）tube(semi-rigid)●波纹 corrugated3.2 内导体设计 Design of inner conductor●实芯线 solid wire●绞合线 stranded wire●金属管 tube●螺纹管 screwed tube3.3 电缆结构 Cable construction●内导体 inner conductor●介质 dielectric●屏蔽层 shielding layer 编织层 braid layer/ply●护套 jacket3.4 电缆材料●镀锡铜 TC=tinned copper●铜包钢 BCCS=bare copper clad steel●镀银铜线 SC=silver covered copper●镀锡铜线 tinned copper●铜包钢线 CCS=copper clad steel●镀银铜包钢线 SCCS=silver covered copper clad steel●铜包铝线 BCCAl=bare copper clad aluminum●镀锡铜编织层 tinned copper braid●裸导线/无镀层导体 plain conductor●裸线, 裸导线 naked wire4. 电缆的装接方式 Cable attachment method4.1 柔软电缆 Flexible cable●压接式 crimp●夹持式 clamp4.2 半刚电缆 Semi-rigid cable●焊接式 solder5. 其它 Others●电缆旋转（挠动）cable rotation (nutation)●电缆拉伸 cable pulling●电缆弯曲 cable bending●电缆扭转 cable torsion/twisting●屏蔽线 shielded wire●双绞线 twisted pair●屏蔽双绞电缆 STP=shielded twisted pair●扁形软电缆 flat flexible cable●扁形双芯软线 flat twin flexible cord14●绕包带式 tape wrapping type●挤出型 extruded type●包带节距 tapping pitch射频同轴转接器RF coaxial adapter1. 转接器类型 Adapter types●系列间转接器：between-series adapter●系列内转接器：in-series adapter焊接用词汇●焊接槽 solder bucket●焊接柱 solder spill●焊片 solder gasket●焊锡圈 soldering ring●焊接孔solder eye●浸锡 tin soaked●焊锡丝 tin wire●漏焊 missing welding●虚焊 incomplete weld / weld defect/cold solder joint ●硬钎焊 solder brazing●焊割两用气焊枪 welding and cutting torch●焊接夹具 welding fixture●焊剂/焊料 welding fluid/ flux●焊接应力 welding stress●焊锡坑 solder cup●焊接涂料 welding paste●焊接部分 welding portion●无焊缝的 weldless●烙铁 soldering iron●烙铁架 iron stand●脱焊 loose weld●元器件表面焊接整洁，焊点圆滑 component surface is clearlywelded with smooth welding point●元器件无虚焊，漏焊，错贴 no cold solder joint, solder skipsand wrong welding of components●solder bath method 焊槽法技术要求＆其它 Techinical requirments & others●机械和电气基准面 mechanical and electrical referenceplane●符合RoHS要求 RoHS compliant (e.g.this part complies withRoHS)●括号中尺寸为参考尺寸dimensions with（）denote referencedimensions●铣槽和涨口/收口 slotted & flared/closed●去除毛刺 remove burrs/ deburr16●除锈 rust cleaning/removing●点铆 stamp●扩口 enlarge kerfs●毛边flash●编织层翻边 wrap the braid over the braid clamp(衬套)●外观，外形 appearance/outline●界面防水等级 interface waterproof level●标记内容：商标 型号 批次号 labels: trade mark，type， batchnumber●未注明公差按… non-specified tolerances according...●…要求为非磁性材料 …required to have non-magneticmaterial●导电环氧树脂回填 conductive epoxy back fill●外观检查：镀层表面无斑点和痕迹，界面无金属碎屑 Visualinspection: plating surface must be without spot and cinch marks; interface must be clean of metal chip●外观良好 good appearance●产品承认书 product acknowledgement●喷锡,黑油，无铅工艺 tin sprayed,black oil,lead free●无杂质 free of foreign matter●整涂覆 overall braid●现场安装field installation●两体结构two-body structure●尾部微带 rear strip●中心接触件弹性支撑center contact with elasticity support缩写和首字母缩写词 Abbreviations & acronyms:●连接器 CONN=connector●接触件 CONT=contact●超小D型连接器 D-sub CONN=D-subminiature connector●阴连接器/外壳 HSG=housing●印制电路板 PCB=print circuit board●产品型号，零件号 P/N=part number●订购单 P/O=purchasing order●数量 QTY=quantity●图纸 DWG=drawing●组件 ASS’Y=assembly●日期代码 D/C=date code●序号，编号 S/N=serial number●不良品，不合格品 NG=no good●不适用 N/A=not applicable●不可用，无法使用 N.A.=not available●直角 R/A=right angle●检验水平 IL=inspection level●可接受的 AC=acceptable18●可接受质量水平 AQL=acceptable quality level●退货，拒收 REJ=rejection●物料单，材料（零件）清单 BOM=bill of materials●无源交调 PIM=passive intermodulation●三阶交调 IM3= Intermodulation 3-tone●印制电路板PCB= printed circuit board●技术更改指令 ECO=Engineering Change Order●工程更改请求 ECR= Engineering Change Request●工艺更改通知单 PCN=Process Change Notice●制程能力/生产过程能力指数 CPK=capability of productionindex●过程工艺持续改进 CPI=continuous process improvement●大批量生成 MP=mass production●操作指南，使用说明书 OI=operating instruction●生产制造 MFG=manufacturing●作业指导书，制作规程 MI=manufacturing instruction●生产控制 PC=production control●质量保证 QA=quality assurance●质量控制 QC=quality control●统计过程管控 SPC=statistical process control●十亿分之一 PPB=part per billion●百万分之一 PPM=part per million●尽快 ASAP=as soon as possible●供参考 FYI=for your information●美国线规 AWG=American wire gauge(e.g. AWG23,意思就是23号线)●平均线规 AWG=Average wire gauge●部门 Dept.=department●有 W/=with●没有 W/O=without**瓦楞纸箱 corrugated carton/slotted carton20。
连接器专用英语对照
连接器专用英语对照Connecter 连接器Cable 导线Wire-to-wire 线至线Wire-to-board 线至板Mini-universal 小型通用Circular plastic connectors 塑料密封环连接器DL (dual-leaf) contact sockets 双叶式触点插座Drawn spring DIP contact socket 弹簧触点插座Zig-zag package sockets 锯齿形封装插座Positive lock connectors 确立锁定连接器Coax mix 同轴混合Shielded circular DIN connectors 屏蔽式圆型DIN连接器Memory card connectors 记忆装置插结连接器SIMM sockets 单列记忆模件插座Low profile 低高度CIS (commercial interconnection system) 商用连接系统Hinge connectors 铰连连接器Card-edge connectors 边缘插接连接器Euro card connectors 欧式插接连接器Modular interconnection system 组合连接系统interconnection system 互连系统RF connectors 射频连接器Twin-Ax connectors 双轴互连系统Low profile coaxial tap 低高度型有源同轴电缆线器4 position data connectors 4位数据连接器Insulation and wire support 绝缘体及导线套Ring-Tongue terminals 环形舌端子Wire size range 线径范围Slotted-Tongue terminals 叉式舌片端子Butt splices 对头接头Dentented Ring-Tongue terminals 卡爪环舌型端子Fits tab thickness 配合接片厚度Accepts terminals 配合端子Crimp-type tabs 压接式接片Free-Hanging and Panel-Mount Applications 自由悬挂及面板装嵌适用Cable clamp 电缆钳位夹PC Board vertical pin headers 垂直接插式接插头组件PC Board Right-Angle pin and socket headers 水平接插式接插头组件Panel-Mount connectors 面板装嵌连接器Insulation Displacement plugs 绝缘位移连接插头Dielectric withstanding voltage 介质承受电压Free-Hanging type cap housings 自由悬挂式套座壳体Semiautomatic crimping machine 半自动压接机Power supply 供给功率Air pir pressure 气压Panel mount type cap housings 面板装嵌套座壳体Post header for printed circuit board 印刷底板用柱头Mass termination assemblies 集体端接组件Post header assemblies 接插柱头组件Polarized right angle post header assembly 有极向性水平接插柱头组件Friction lock 锁尖装置Sigle leaf connectors 单叶片连接器CPC (circular plastic connectors) 塑料密封环型连接器Ceimp Snap-In contacts 压接式套入触点Socket with straight solder tails 直立焊脚插座Retention feature solder tails 弯曲焊脚Sockets with retention feature solder tails 面板附定曲脚插座High Pressure Tin (HPT) sockets 镀锡高压芯片Positive lock retention feature 彻底锁定装置Plug-Grounding Indents 插头外罩接地凹位Solder Cup connector 焊杯触点连接器Straight Exit RFI/EMI shield for Jacketed cable 直线引出RFI/EMI屏蔽外壳外套导线束适用Backshell assembly 后部外壳组件Board-Mount connectors with threaded inserts and board locks 底板安装连接器附内丝牙及板扣Board-Mount Receptacles 底板安装插座Non-Polarized Receptacles 无定位型插座Handset plug assembly 电话线插头组件Line cord plug assembly 听筒插头组件。
连接器常用英语汇整
1.连接器产品零部件英语术语 连接器产品零部件英语术语
A.连接器 连接器 connector / conn. 卧式类型（也称90度） Right Angle Type (RA) 直立式类型（也称180度） Vertical Type 侧插式（也称侧立式） Flag Type 破板式类型（也称沉板式） Offset Type 穿孔式 DIP Type 表面粘着技术 SMT 母端 Female/ Receptacle 公端 Male/ Plug PCB线路图 PCB Layout 冲压 stamping 成型 molding 组装 assembly 自动机 Auto machine 治具 Fixture/JIG 塑模 mold tooling 冲模 die 电镀 plating 闪镀金 Gold flash（GF） 尺寸 Dimensions 公差 Tolerance 设计失效模式分析 DFMEA 过程失效模式分析 PFMEA
2.连接器测试常用英语 连接器测试常用英语
A.ELECTRICAL 电气要求 Contact Resistance 接触阻抗 Low Level Contact Resistance (LLCR) 低电压接触阻抗 Insulation Resistance 绝缘阻抗 Current Rating 额定电流 Voltage Rating 额定电压 Dielectric strength /Dielectric Withstanding Voltage 耐电压 B.MECHANICAL 机械要求 Insertion & Withdrawal Force / Mating & un-mating force 插入力/拔出力 Normal Force （端子）正向力 Durability 寿命、耐久 Vibration 震动 Mechanical Shock 机械振动 Retention Force （端子）保持力 Solder-ability 沾锡性 C. ENVIRONMENTAL 环境要求 Thermal Shock 冷热冲击 Salt Spray 盐雾 Humidity 耐湿性、恒温恒湿 Solder heat resistance 耐焊性
连接器英文专业类术语
>>技术支持 - 连接器英文专业类术语冲压类punch, press冲punching machine 冲床hydraulic machine油压机jack升降机decoiler整平机manufacture management製造管理stamping, press冲压feeder送料机rack, shelf, stack料架taker取料机to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped |’skr鎝id|报废scrape ..v.刮;削robot机械手production line流水线packaging tool打包机packaging打包成型类well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head鉋尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头鉤销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口runner less无浇道sprue less 无射料管方式long nozzle延长喷嘴方式spur浇口;溶waste废料board看板sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理组装类Assembly line组装线Layout布置图Conveyer流水线运输带Rivet machine拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Hydraulic machine 液压机Pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氬焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运be put in storage入库packing包装staker = riveting machine铆合机。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
连接器常用的专业术语1. 连接器：通常装接在电缆或设备上，供传输线系统电连接的可分离元件（转接器除外）。
2. 射频连接器：是在射频范围内使用的连接器。
3. 视频：频率范围在3HZ∽30MHZ之间的无线电波。
4. 射频：频率范围在3千HZ∽3000GHZ之间的无线电波。
5. 高频：频率范围在3MHZ∽30MHZ之间的无线电波。
6. 同轴：内导体具有介质支撑，结构上能在测量中采用频率范围内得到最小的内反射系数。
7. 三同轴：由具有公共轴线并且相互绝缘的三层同心导体组成的传输线。
8. 等级：连接器在机械和电气精密度方面特别是在规定的反射系数方面的水平。
9. 通用连接器（2级）：采用最宽的容许尺寸偏差（公差）制造，但仍能保证最低限度的规定性能和互配性的一种连接器。
注：反射系数的要求可规定，也可以不规定。
10.高性能连接器（1级）：按频率变化来规定反射系数极限值的一种连接器，通常所规定的尺寸公差不比相应的2级连接器严格，但是需要保证连接器满足反射系数的要求时，制造厂有责任选择较严的公差。
11.标准试验连接器(0级)：用来对1级和2级连接器进行反射系数测量的一种精密制造的具体类型连接器，对测量结果引起的误差可以忽略不计。
注：标准试验连接器通常是不同类型间转接器的一部分，而转接器与精密连接器连接构成测试设备的一部分。
12.密封12.1密封连接器：具有能满足规定的气体，潮气或液体密封性要求的连接器。
12.2隔障密封：防止与气体、潮气或液体沿着轴向进入连接器壳体内部的密封。
12.3面板密封：防止气体、潮气或液体通过安装孔进入固定或转接器壳体与面板之间的密封。
注：密封件通常作为独立产品提供。
12.4插合面密封：防止气体、潮气或液体进入一对插合连接器界面处的密封。
12.5气密封：满足IEC60068-2-17《基本环境试验规程第2部分：试验-试验Q：密封》中试验Qk规定要求的密封。
连接器的基本结构组成：连接器的基本结构件有①接触件；②绝缘体；③外壳（视品种而定）；④附件。
1．接触件（contacts）是连接器完成电连接功能的核心零件。
一般由阳性接触件和阴性接触件组成接触对，通过阴、阳接触件的插合完成电连接。
阳性接触件为刚性零件，其形状为圆柱形（圆插针）、方柱形（方插针）或扁平形（插片）。
阳性接触件一般由黄铜、磷青铜制成。
阴性接触件即插孔，是接触对的关键零件，它依靠弹性结构在与插针插合时发生弹性变形而产生弹性力与阳性接触件形成紧密接触，完成连接。
插孔的结构种类很多，有圆筒型（劈槽、缩口）、音叉型、悬臂梁型（纵向开槽）、折迭型（纵向开槽，9字形）、盒形（方插孔）以及双曲面线簧插孔等。
2．绝缘体绝缘体也常称为基座（base）或安装板（insert），它的作用是使接触件按所需要的位置和间距排列，并保证接触件之间和接触件与外壳之间的绝缘性能。
良好的绝缘电阻、耐电压性能以及易加工性是选择绝缘材料加工成绝缘体的基本要求。
3．壳体也称外壳（shell），是连接器的外罩，它为内装的绝缘安装板和插针提供机械保护，并提供插头和插座插合时的对准，进而将连接器固定到设备上。
4．附件附件分结构附件和安装附件。
结构附件如卡圈、定位键、定位销、导向销、联接环、电缆夹、密封圈、密封垫等。
安装附件如螺钉、螺母、螺杆、弹簧圈等。
附件大都有标准件和通用件。
连接器专业术语冲压类punch, press冲punching machine 冲床hydraulic machine油压机jack升降机decoiler整平机manufacture management製造管理stamping, press冲压feeder送料机rack, shelf, stack料架taker取料机to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped |\’skr鎝id|报废scrape ..v.刮;削robot机械手production line流水线packaging tool打包机packaging打包成型类well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head鉋尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头鉤销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口runner less无浇道sprue less 无射料管方式long nozzle延长喷嘴方式spur浇口;溶waste废料board看板sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理组装类Assembly line组装线Layout布置图Conveyer流水线运\输带Rivet machine拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Hydraulic machine 液压机Pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氬焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运\be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine/heat stake热熔机processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机品质类qualified products, up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part来件不良exposed metal/bare metal金属裸露excessive defect过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格cosmetic defect外观不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑丝missing part漏件wrong part错件oxidation氧化defective threading抽芽不良poor staking铆合不良deficient purchase来料不良deficient manufacturing procedure制程不良cosmetic inspection外观检查inner parts inspection内部检查blister 气泡angular offset 角度偏差dent 压痕scratch 刮伤deformation 变形filings 铁削defective label 不良标签abrasion 磨损Breaking. (be)broken,(be)cracked 断裂short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delaminating起鳞speckle斑点mildewed =moldy = mouldy发霉deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质shrinking/shrinkage缩水mixed color杂色fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍impurity 杂质Mismatch 错位failure, trouble 故障deformation 变形rust 生銹peel 脱漆Shrink 缩水Contamination 臟污water spots 水渍Gap 间隙label error 标签错误Missing label 漏贴rejection criteria 拒收标准Suspected rejects 可疑庇abrasion 损伤、磨损Texture surface 印花纹表面Streak 条纹stains 污点Blotch 斑点discoloration 脱色Inclusion 杂质slug mark 压痕dirt grime 灰尘blush 毛边薄膜sink 下凹Hickey 漏漆labels and logos 贴纸与商标Configuration labels 组合贴纸corrugated container 瓦摆纸箱Delaminating 脱层splattering 散点Gouge 銼孔puckering 折痕通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |\’depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位Human Resources Department人力资源部Head count 人头数production department生產部门planning department企划部QC Section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生產单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management 顏色管理Visual management 目视管理production capacity生產力first count初盘first check初盘復櫂second count 復盘second check復盘復核quantity of physical inventory second count 復盘点数量physical inventory盘点数量physical count quantity帐面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 电脑外壳(组件)personal computer enclosure 电脑机箱產品front plate前板rear plate后板chassis |\’∫鎠i| 基座bezel panel面板Hood 上盖base pan 基座bezel 面板riser card 扩充卡flat cable 排线TOP driver cage 上磁架bottom driver cage 下磁架resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material捲料spare parts =buffer备品plastic parts塑胶件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程表单production tempo生產进度现状lots of production生產批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套Band-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生產equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机club car高尔夫球车plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler 天车trailer =long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate座标supply and demand供求career card履歷卡barricade隔板carton box纸箱to pull and stretch拉深work cell/work shop工作间sub-line支线bottleneck 瓶颈模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模stage die工程模compound die復合模shearing die剪边模riveting die铆合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 换模to fix a die装模to repair a die修模punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)upper supporting blank上承板upper padding plate blank上垫板top plate上托板（顶板）top block上垫脚stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶桿trimming punch切边冲子stiffening rib punch = stinger 加强筋衝子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块die locker锁模器pressure plate =plate pinch压板thickness gauge厚薄规cutting die, blanking die冲裁模die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条panel board镶块to load a die装上模具to unload a die 御模具active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶桿spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块pilot导正筒trim剪外边pierce剪内边pocket for the punch head挂鉤槽slug hole废料孔radius半径shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺丝form block折刀round pierce punch =die button圆冲子shape punch =die insert异形子stock located block定位块metal plate鈑金miller铣床grinder磨床tolerance公差score =groove压线sliding block滑块lathe车active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶桿spring-box eject-plate弹簧箱顶板capability能力parameter参数factor系数driller鉆床set up die架模height of die setting up架模高度analog-mode device类模器inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves =spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套press specification冲床规格die height闭模高度flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝stripper plate脱料板piston活塞handle mold手持式模具flash mold溢流式模具positive mold挤压式模具split mold分割式模具die lifter举模器top stop上死点bottom stop下死点one stroke一行程to continue, cont.连动to grip(material)吸料location lump, locating piece, location block定位块reset復位to file burr 銼毛刺embedded lump |in\’bed| |l賛p|镶块stamping-missing漏冲to tight a bolt拧紧螺栓to loosen a bolt拧鬆螺栓punched hole冲孔to cut edge =side cut =side scrap 切边to bending折弯to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake铆合designing, to design设计design modification 设计脩改成gauge(or jig)治具pedal踩踏板stopper阻挡器flow board流水板torque扭矩spline =the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel鉬高速的forming成型(抽凸,冲凸)draw hole抽孔bending折弯emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线stamp letter冲字(料号)tick-mark nearside正面压印tick-mark farside反面压印extension DWG展开图procedure DWG工程图die structure DWG模具结构图。