船舶英语汇总审批稿
船舶专用英语汇总
船舶专用英语汇总船舶专业英文词汇No.1船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing)计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling)取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle ofinclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and ReviewTechnique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank底边舱斜顶板slopint bottom plate of topside tank定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioningdiagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇来自：navigation > 《ship》上一篇：船舶保安员工作要点下一篇：海洋运输常用英文缩略语转藏到我的图书馆献花(1) 分享到微信以文找文分享：人人网开心网搜狐微博推荐给朋友举报类似文章更多∙船舶专业英语词汇∙船体制图常用英中名词术语对照∙船舶英语(页1) - 设计学习- 千岛热线论....∙船体结构英语∙船舶英语手册1--5∙Navis.gr - 3Examination Questions For...∙船舶图纸符号大全∙货运保险鉴定常用词汇。
船舶常用英语(一)
一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料)T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start) 不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammablevapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊。
船舶制造英语日常用语
Accept 接收Accept subject to 有条件的接收，有待于……做好之后才接收Reject 拒收Comments 意见 defect lish 消除意见清单Item 项目memorandum 备忘录manual n、手册、说明书；a.手控的，手工的drawings 图纸working drawings 施工图finished drawings 完工图approved drawings 认可图drawings for approval 送审认可图supporting technical doucuments 基础技术文件sketch 草图 draw a sketch画草图up to the standard 达到标准substandard 低于标准的crane 吊车building berth 船台slipway 船台、下水滑道dry dock 干无坞pier 突码头、突堤wharf 码头along side (船)靠码头foreman 工长，领班coordinator 调度员inspector 检查员supervisor 管理人、监督人，监造人surveyor 验船师2、船体总体，及各类型船舶Hull 船体Forecastle 艏楼Stern 船尾Poop 艉楼Superstructure 上层建筑Foremast 前桅杆After mast 后桅杆Radar mast 雷达桅杆Main deck 主甲板Upper deck 上甲板Poop deck 艉楼甲板Accommodation deck 生活甲板Compass deck 罗经甲板Funnel 烟囱Bridge 桥楼，驾驶台Bridge wing 驾驶室翼桥Wheel house 驾驶室Engine room 机舱Engine control room 机舱集控室Catwalk 天桥、步桥Flying bridge （露天）航行驾驶室Rescue boat 救助艇Life boat 救生艇M/Vmerchant vessels 商船Naval Auxilary vessel 军用船Naval Ship/war shipd 军船Ice-breaker 破冰船Container vessel 集装箱船Oil tanker 油轮Products tanks 成品油轮Carrier 运输船、航空母舰、托架Chemical carrier 化学品运输船Liquefied gas carrier 液化气体船Liquefied natural gas carrier 液化天然气运输船Aircraft carrier/aeroplane carrier 航空母舰School ship/training ship 训练船Geophysical survey ship 地球物理勘探船Cruiser 巡洋舰、大型快船、游艇Canoe 独木船，皮舟Junk 平底中国帆船、舳板Gondola （意大利威尼斯的）一种狭长的平底船Yacht 快艇、游艇Fast boat 快艇Patrol boat 巡逻艇Anti-smuggling boat 缉私艇Torpedo boat 公安艇Ferry 渡船Catamaran 双体船Jet foil 喷水水翼艇Wing assrsted vessel 地效船3、各专业基本词汇1）船体：Draft forward 前吃水Draft middle 中吃水Draft after 后吃水Plimsoll mark/lineWaterline 吃水线Waterlines （型）水线Port 左舷Starboard 右舷Sagging 中垂、下垂、下挂（流）Hogging 中拱、上拱Derformation 变形Fairing 光顺、火工校正Hot work热工、明火作业section 分段、部分、剖面Block 分段Keel （船舶）龙骨Bilge keel 舭龙骨Power tool 带动力工具（风动或电动）Welder 电焊工Welding machine 电焊机A.C welding 交流（电弧）焊D.C welding 直流（电弧）焊Grinding 打磨Welding 电焊Spatters 飞溅（电焊）Under out 咬口Bulwark舷墙，防浪板Wall墙壁Floor地板Controllable pitch 可调桨Elastic coupling 弹性联轴节Bellow 波纹管Joint接头Gaskets垫片Fitting bolts 拂螺拴Chock 制动块、导缆器Chock fast 环氧垫块Foundation 底座、基座Mounting 装置、座、架Mount （常指火炮等武器的）座，架Vent pipe 透气管Sounding pipe探测管Vapour return line油气回路管Stripping line扫舱管Safety equipment 安全设备Life-saving equipment救生设备Cargo hold 货舱Cargo oil tank货油舱Cabin 船舱、舱室Room房间Store room储藏室Cold room冷库Fish room鱼库Meat room 肉库Provision room粮库Foam room 泡沫库CO2 room二氧化碳室Pump room泵室Battery room蓄电池室Radio room 报务室Galley 厨房Ventilation system 通风系统Fresh water piping system 淡水系统Sea water piping system 海水管系Water jacket水套Insulation materials绝缘材料Lagging绝缘材料、外套（锅炉、管子等）3）电器Current电流Voltage电压Frequency频率Contact触点、触头Ballast镇流器Convertor变频器、换能器Conductor导体Semi-conductor半导体Rectifier整流器Transformer变压器Thermostat 恒温器Thermister热敏器Edison base 螺丝灯座、爱迪生灯座Bayonet base卡口灯座On-off开关（量）Analogue模拟，模拟设备Active analogue有源模拟、主动模拟Passive analogue无源模拟、被动模拟Dry contact无源模拟、干接触Buzzer蜂鸣器Button按扭，电扭Switch开关Main switch主开关Main switch board主配电板Cable 电缆Wire 电线Three-core cable三蕊电缆Clamp夹钳、夹具Clip 接线柱、线夹Alligator clip鳄鱼夹、弹簧夹Voltage drop 电压降Speed droop速度降低Black out 黑灯试验Power failure失电Setting point 设定点Adjust 调正（v）Adjustment调正（n）Oscillator振荡器、振动器Oscilloprobe示波器测试头Oscilloscope示波器、示波仪Resistor电阻、电阻器Potentiometer电位器、电势计Electrolysis电解（作用）Electrolyte电解质、电解液setting point of power surplus负载余量设定值重载询问test the power surplus setting point重载询问试验4）漆、木Surface preparation表面处理（清理工作）Blasting equipment喷漆（砂粒）装置Sand blasting 喷砂除锈Pre-blasting预喷砂Light blasting 预喷砂Full blasting 通喷砂Sand sweep扫砂Sand blasting to SA2.5喷砂达到SA2.5级Steel work inspection after full blast ing通喷砂后钢结构检查Cleanliness inspection清洁度检查Inspection after degreasing除去油脂后检查Removing oil stains by detergent/solve nt使用洗洁剂/容剂除去油迹Shop primer 车间底漆Spray painting喷漆、喷涂法Touch-up 补漆、修正Touch-up painting补漆、点漆First coat 底漆、头道漆Finish coat 面漆Surface coat 表面涂层Under coat 内涂层Locking device闭锁装置，制动设备Plywood胶合板，层压板Laminated plate迭层板Laminate层压制品，迭层板，层压板High pressure washing of the hull 用高压水冲洗船壳Steel plate temperature 钢板温度Condensation冷凝Capillary condensation毛细管现象Dew point露点Flashing point闪点Ignition point 燃点，着火点Ventilation for coating 涂装通风Dehumidifier去湿机，干燥机Dehumidification 去湿，去潮Sagging流挂，下垂Chalking粉化Peeling剥落（指油漆）Pinhole针孔CureCuring硬化，熟化，硫化Drying film thickness(DFT)干膜（漆膜）厚度Curing temperature硬化、固化温度Power tools有动力的工具（包括电动及风动）Pheomatic tools风动工具Burnt area烧坏的区域Oil stains油迹Scratches划痕Damaged places遭损坏的部位Chicken wire钢丝网Tiles瓷砖，瓦Mosaic-tile彩色瓷砖，镶嵌瓷砖，马赛克瓷砖Glue胶，粘结剂Silica硅石，二氧化碳Silicagel硅胶Decoration装饰，装修Interior decoration内部装饰，内装Deck head 天花板Ceiling天花板Paneling板墙，镶板Wall墙壁Desk书桌，桌台Drawer 抽屉Catch hook固定钩子Observation window 观察窗Inspection window检查孔窗Clear view window旋转观察窗Curtain 窗帘Latch止动销，插销Valance窗帘箱Hanging窗帘Eyebrow舷窗眉板Pre-alarm预报警Trip脱扣，跳闸Preferential trip优先脱扣Transducer换能器synchronize（便）同步synchronize motor同步电机synchronous motor异步电机step motor步进电机diode二极管triode三极管audion三极管single phase单相three phase三相phase-in逐步引进phase-shafting相移retarding phase 滞后相位reversed phase倒相，相反relay继电器timer定时器trimmer微调电容器，调正片delay延时carrier载波，载波电流transponder发射器，应答器，询问机echo-sound回声测深仪radio navigation equipment无线电导航设备log计程仪auto-pilot自动驾驶仪gyro-compass电罗经barrier屏障，障碍，栅栏zenner barrier齐纳屏（使电只能单向流的半导体）radio beacon无线电信标pluse脉冲blanking plus 消隐脉冲induction感应，感应现象oscillation振荡Leak(v)渗，漏Leakage(n) 渗，漏Overhaul大修，彻底检修Hammer榔头Spanner扳手，扳头Ring spanner环形扳手，梅花扳手Allen key 内六角扳手，Box spanner套筒扳手Torque spanner扭力扳手Double-ended spanner双头扳手Monkey spanner活络扳手，活络管扳手Shifting spanner活络扳手Pipe spanner管子扳手Reamer铰刀Reaming （用）铰（刀扩）孔Countersink reamer锥形孔铰刀Wrench扳手，扳头Shisel凿子Calipers卡钳，两脚规Inside calipers内卡钳Bore 内孔Boroscopic inspection内孔表面检查Boroscope内孔表面检查仪Plug塞（子），（内燃机）火花塞Cock施塞，龙头Valve阀P/V valve P/V阀Strainer滤器Coarse strainer粗滤器Fine strainer精滤器Oil separator分油机Back pressure背压Pressure test压力试验Over speed 超速Over load超负荷Dafety device 安全装置Fly wheel飞轮Floating floor 浮式地板Deckhead 天花板（指由甲板形成的）Ladder 梯子Vertical ladder直梯Inclined ladder斜梯Accommodation ladder舷梯Cleanliness inspection after flushing F .O piping system燃油管串油后清洁检查Function test of steering gear舵机效甩试验Hose test of water tight doors水密门冲水试验Noise lever measurement噪声测量Vibration level measurement 振动测量Main engine (M/E)主机Generator发电机Emergency generator应急发电机Shaft generator轴带发电机Fresh water generator 制淡装置Steering gear 舵机General service pump总用泵Pire pump消防泵Hydraulic motor 液压马达Hydraulic nuts液压螺帽Rudder舵Rudder bl ade舵叶Propeller车叶，螺旋桨Fixed pitch propeller固定螺距的螺旋桨Lofting型线图放样Lay off（船及部件）放样，下料Plate-cutting钢板下料，开工Numerically-controlled cutting machine 数控切割机Cutting machine切割机Under water plasma cutting machine水下等离子切割机Surface preparation表面处理Fabrication（焊）开坡口，边缘加工（如刨边）Upside down construction method分段装配Assembly 反身建法Erection装配，大合拢Jig装配架，胎架Bow jip 船首部胎架Girder纵向构件，桁（材）Beam梁，横梁Sections型材Profile型钢（条）Bar 杆，棒,棒材Plate板材Angle bar角钢I beam（窄缘）工字梁H beam（宽缘）工字梁Stiffener扶强材Bracket托架，支架，肘板Support 支架Frame肋骨，框架Douler复板Coaming（舱口）围板，缘材Sinp剪切Cut切割Anchor锚Anchor widdlass 锚机Anchorage锚位，锚地Chain链Chain block链条滑车，神仙滑车Platform平台Crossover跨越（梯桥），立交Life raft 救身筏Life buoy 救生圈Forward winch 前绞缆机After winch 后绞缆机Windlass锚机Bitt带缆桩，系桩Fairlead导缆钳，导缆孔Hand rail扶手，栏杆Beam横梁Frame肋骨，框架Scantling构件尺寸Cargo oil tank货油舱Scantling draft结构吃水Forepeak tank首尖舱After peak tank尾尖舱Water ballast tanks(W.B.T)压载水舱Fuel oil tank(F.O.T)燃油舱Lubricating oil tank(L.OT)滑油舱Diesel oil tank(D.O.T)柴油舱Double botton双层底Double skin双层外板，双层蒙皮Bow thruster艏侧推Propeller车叶Fixed pitch propeller定螺距螺旋桨Controllable pitch propeller(CPP)可调螺距螺旋桨Shaft轴Tail shart尾轴Shaft generator轴带发电机Watertight doors水密门Bulwark舷墙Bulkhead舱壁Tank top内底，液舱顶Hatch cover舱口盖Manhole人孔Fin stablizer减摇鳍Antifouling system防海生物的，防污染系统Ship船Vessel船，舰Fabrication制造，分段装配（precfabrication预制，预加工）Assemble装配，组装Erection大合拢，船台装配Staging脚手架Block stage分段阶段Mile stone（里程碑，大节点）Plate-cutting下料，开工Keel-laying上船台，龙骨铺设Lauching下水mooring trial码头试验，系泊试验sea trial(sea)试航delivery of the ship交船defect list by the owner/society船东提出的消除意见清单/船级社提出的消除意见清单design stage设计阶段submit drawings to owner,classification society(LR、DNV、BV、ABS，etc)for approval 向船东，船级社（劳氏，挪威，法国，美国等）提交认可图纸hull workshop船体车间machining workshop金工车间machinery engineering workshop轮机车间electrical workshop电气车间business dept.经营处perchasing dept.供应处Q.C.Dept.检验处Design dept.设计室Painting and carpenter’s workshop漆木车间Project manager项目经理Director指导者，厂长，董事Managing director执行董事，常务董事，总经理。
船舶专业英语汇总
主船体main hull上层建筑superstructure上甲板/上层连续甲板upper deck船底bottom舷侧broadside艏艉fore and aft舱壁bulkhead水密watertight艏部bow艉部stern/quarter二层甲板second deck平台甲板platform deck桅屋masthouse罗经甲板compass deck驾驶甲板bridge deck船长甲板master deck高级船员甲板office deck艇甲板boat deck船员甲板crew deck机舱engine room货舱cargo hold货舱口cargo hatch压载舱ballast tank深舱deep tank 燃油舱fuel oil tank滑油舱lubricating oil tank淡水舱fresh water tank污油水舱slop tank隔离空舱/干隔舱caisson球鼻艏标志bulbous bow mark/BB mark首侧推器标志bow thruster mark/BT mark吃水标志draft mark甲板线deck line干舷甲板freeboard deck载重线标志load line mark热带淡水载重线tropical fresh water load line/TF夏季淡水载重线fresh water load line/F热带载重线tropical load line/T夏季载重线summer load line/S冬季载重线winter load line北大西洋冬季载重线winter North Atlantic load line/WNA 国际船舶载重线证书international load line certificate吃水指示系统draft indicating system船舶尺度ship dimension最大尺度/全部尺度/周界尺度overall dimension最大长度/全长/总长length overall/LOA最大宽度/全宽extreme breadth最大高度maximum height净空高度air draught船型尺度/型尺度/主持度moulded dimension 垂线间长L/length between perpendiculars型宽B/moulded breadth型深D/moulded depth型吃水d/moulded draft登记尺度register dimension登记长度register length登记宽度register breadth登记深度register depth船舶主尺度比dimension ratio船长型宽比L/B , length breadth ratio船长型深比L/D , length depth ratio船长型吃水比L/d , length draft ratio型宽型吃水比B/d , breadth draft ratio型深型吃水比D/d , depth draft ratio重量吨weight tonnage排水量displacement满载排水量dead displacement空船排水量light displacement装载排水量load displacement总载重量deadweight/DW净载重量net deadweight/NDW容积吨/登记吨capacity tonnage总吨位/总吨gross tonnage/GT净吨位net tonnage/NT运河吨位canal tonnage/CT抗沉性floatability全客船passenger vessel客货船passenger-cargo vessel货客船cargo-passenger vessel客滚船ro-ro passenger ship集装箱船container ship箱格导轨系统cellguide system散装货船bulk carrier散装货物bulk cargo舱口围板hatch coaming横剖面cross-section边舱side tank压载舱ballast tank矿砂船ore carrier压载边舱side ballast tank内底板inner bottom plating兼用船combination carrier矿砂/石油两用船，O/O船ore/oil carrier矿砂/散货/石油三用船，OBO船ore/bulk/oil carrier杂货船general cargo ship滚装船roll on/roll off ship , Ro/Ro ship木材船timber carrier冷藏船refrigerated ship多用途船multi-purpose ship液货船liquid cargo ship易燃液体inflammable liquid油船oil tanker污油水舱slop tank液体化学品船liquid chemical tanker液化气船liquefied gas carrier液化天然气船liquefied natural gas carrier/LNG carrier 液化石油气船liquefied petroleum gas carrier/LPG carrier 乙烯运输船ethylene tanker工程船engineering ship挖泥船dredger起重船floating crane海洋调查船marine survey ship敷缆船cable ship航标船navigation mark ship工作船working ship拖船tug供应船supply boat破冰船icebreaker海难救助船rescue ship消防船fire boat科学考察船scientific research ship船体结构ship construction钢板plate型钢section steel扁钢flat bar球扁钢bulb bar角钢angle bar , A/B工字钢I-barT型钢T-bar槽钢channel bar铸钢，铸件casting锻钢，锻件forging焊接welding周围焊around welding电弧焊/电焊electric arc welding气焊gas welding焊缝weld塞焊plug welding端接焊end welding角接焊fillet welding对接焊butt welding搭接焊lap welding坡口groove覆板doubling plate铆接riveting板材deals and battens骨架skeleton总纵强度total longitudinal strength 扭转强度torsional strength横向强度transverse strength局部强度local strength坐坞强度docking strength刚度rigidity稳定性stability应力集中stress concentration船台building berth横骨架式transverse framing system 横向构件transverse member舷顶列板sheer strake舷侧板side plating舭列板bilge strake船底板bottom plating中内龙骨center keelson旁内龙骨side keelson梁肘板beam knee平板龙骨(flat) plate keel甲板纵桁deck girder肋骨frame强肋骨web frame舷侧纵桁side girder肋板floor横梁beam横舱壁板transverse bulkhead plating 舱容hold capacity外板shell plate内底板inner bottom plating纵向构件longitudinal member自重sole weight纵骨架式longitudinal framing system船底纵骨bottom longitudinal中桁材center girder旁桁材side girder舷顶列板sheer strake舷侧纵骨 side longitudinal撑材strut甲板纵骨deck longitudinal强横梁web beam舱口围板hatch coaming纵舱壁longitudinal bulkhead舭龙骨bilge keel二层甲板tween deck内底边板margin plate实肋板/主肋板solid floor内底纵骨inner bottom longitudinal加强筋stiffener人孔manhole舱口端梁hatch end beam支柱pillar船舱肋骨hold frame甲板间肋骨tweendeck frame舷侧列板side strake舭肘板/污水沟三角板bilge bracket舱口端横梁hatch end beam防倾肘板tripping bracket舷墙板bulwark plating舷强扶强材bulwark stiffener换新renew基本结构图basic construction plan纵中剖面结构图central fore-and-aft plane construction plan 各层甲板图deck plan内底结构图inner bottom construction plan列板strake舭列板bilge strake甲板边板deck stringer基线base line横剖面图transverse cross-section plan中横剖面图midship transverse cross-section plan机舱处横剖面图engine-room transverse cross-section plan 货舱口处横剖面图cargo hatch transverse cross-section plan 舱壁图bulkhead plan总布置图general arrangement plan船底结构bottom construction下甲板横梁lower deck beam上甲板横梁upper deck beam支柱肘板pillar bracket双层底结构double bottom construction骨架framing首防撞舱壁fore collision bulkhead尾尖舱舱壁afterpeak bulkhead肘板bracket水密肋板watertight floor内底纵骨inner bottom longitudinal实肋板solid floor组合肋板/框架肋板bracket floor扶强材side girder船底横骨bottom frame流水孔drain hole透气孔air hole减轻孔lightening hole切口incision内底横骨inner bottom frame水密舱壁watertight bulkhead横骨架式双层底结构transversely framed double bottom construction 轻型肋板lightened floor面板 face plate折边flanging中桁材/中底桁center girder中内底板center inner bottom plating箱形中桁材/箱形龙骨duct keel管隧pipe tunnel水密纵桁watertight longitudinal girder内底纵骨inner bottom longitudinal内底横骨inner bottom frame船底中心线bottom center line旁桁材/旁底桁/旁龙骨side girder人孔盖manhole cover污水沟bilge drainage/side bilge污水井bilge well/bilge sump单层底结构single bottom construction中内龙骨center keelson旁内龙骨side keelson舷侧外板side plating甲板边板deck stringer主肋骨main frame甲板间肋骨tweendeck frame尖舱肋骨peak frame肋距frame space中间肋骨intermediate frame普通肋骨ordinary frame强肋骨web frame舷侧纵桁side stringer舷侧纵骨side longitudinal舷边gunwale舷边角钢gunwale angle bar止裂crack arrest舷墙bulwark舷墙板bulwark plating支撑肘板buttress bracket扶手armrest栏杆hand rail舱口纵桁hatch side girder甲板纵中线deck center line舱口端梁hatch end beam强力甲板strength deck甲板间舱tweendeck space遮蔽甲板shelter deck舱壁甲板bulkhead deck干舷甲板freeboard deck量吨甲板tonnage deck半梁half beam斜置加强筋tilt stowing stiffener管型支柱tubular pillar水平加强筋horizontal stiffener菱形面板diamond plate悬臂梁cantilever beam梁拱camber舷弧线sheer curve舷弧sheer首舷弧fore sheer尾舷弧after sheer首尖舱fore peak tank首尖舱舱壁fore peak tank bulkhead 防撞舱壁collision bulkhead尾尖舱舱壁after peak tank bulkhead 防火舱壁fireproof bulkhead液体舱壁liquid bulkhead油密oiltight制荡舱壁wash bulkhead平面舱壁plane bulkhead舱壁板bulkhead plate舱壁扶强材bulkhead stiffener水平桁horizontal girder对称槽形舱壁symmetrical corrugated bulkhead 三角形triangle矩形rectangle梯形trapezoid弧形arc双层底double bottom tank底边舱lower side tank顶边舱top side tank底登lower stool直立型首straight bow首柱stem/stem post驳船barge前倾型首raked bow飞剪型首clipper bow首楼甲板forecastle deck破冰型首ice resistant bow兴波阻力wave making resistance形状阻力form resistance铸钢首柱cast steel stem post钢板首柱steel plate stem post锚链舱chain locker升高肋板raised floor强胸横梁panting beam外板shell plate开孔平台trepanned platform椭圆形尾elliptical stern巡洋舰形尾cruiser stern方型尾transom stern尾封板stern transom plate船首结构bow construction强力构件strength member剖面模数section modulus船尾结构stern construction尾肋板transom floor尾柱底骨sole piece推进器柱propeller post轴毂propeller boss舵钮rudder gudgeon舵柱rudder post斜横梁cant beam舵机舱平台steering gear room platform尾升高肋板stern raised floor斜肋骨cant frame舵杆管rudder case防火措施fire precaution防火结构fire structure耐火材料refractory material主竖区main vertical zone不燃材料non-combustible material自燃autoignition易燃蒸气inflammable vapour可燃材料combustible material等效材料equivalent material防火分隔fire resisting divisionA级分隔/甲级分隔A class division天花板ceiling衬板furring轴隧shaft tunnel推进器轴propeller shaft逃生孔escape trunk中机型船amidship-engined ship尾机型船stern-engined ship单车船single-screw ship顶板top plating木铺板batten ceiling滑动式水密门slid watertight door拱形顶板arch top plating平顶板flat top plating轴承基座stool supporting shaft bearing 管系piping格子板grating舭龙骨/减摇龙骨bilge keel坞修dock repair船底塞docking plug坞墩docking block锰黄铜manganese brass不锈钢stainless steel舭部外板bilge plate舷侧型线moulded line of side shell船底型线moulded line of bottom shell 垫圈insertion ring垫板pad隔离空舱caisson双层舷侧double side shell双层壳double shell中间舱center tank边舱side tank甲板下纵桁deck lower girder业务衡准数criterion of service numeral舱底水管系bilge system舱底水管路bilge pipe吸口suction过滤器filtrator舱底水总管bilge main line止回阀non-return valve舱底泵bilge pump阀箱valve casing泥箱mud box油水分离器oil-water separator测量管/测深管sounding pipe旋塞faucet螺纹盖thread cap防击板striking plate压载管系ballast system压载水ballast water压载管路ballast pipe调驳阀箱control valve easing压载泵ballast pump截止阀stop valve海底阀/通海阀sea suction valve舷侧排水阀overboard discharge valve空气管air pipe花钢板diamond plate自动关闭阀automatic closing valve通风管系ventilating system自然通风natural ventilation烟斗式通风筒cowl-head ventilator排风筒uptake ventilator蘑菇形通风筒mushroom ventilator起重柱Samson post鹅颈式通风筒gooseneck ventilator机械通风mechanical ventilator风机aerator管路pipe conduit吸口空气滤器suction air filter空气调节air conditioning system消防管系fire extinguishing system固定式灭火系统fixed fire extinguishing system 水灭火系统water fire extinguishing system气体灭火系统gas fire extinguishing system泡沫灭火系统foam fire extinguishing system水雾灭火系统water fog fire extinguishing system自动喷水系统automatic sprinkling fire extinguishing system 惰性气体保护系统inert gas system日用水管系domestic water supply system日用淡水系统domestic fresh water system日用热水系统domestic warm water system饮用水系统potable water system重力水柜gravity tank压力水柜pressure tank循环泵circulating pump甲板排水管系 deck scupper system甲板排水器deck scupper排水管scupper pipe卫生排泄系统sanitary water system锚anchor锚穴anchor recess锚链筒hawse pipe制链器chain stopper锚机windlass锚链管chain pipe锚链舱chain locker锚链chain cable闸刀switch blade制动销detent pin松紧螺丝扣turnbuckle弃链器releasing gear横闩式弃链器dog type cable clench螺旋弃链器screw type cable releaser手轮hand wheel螺杆screw脱钩senhouse slip末端链环end open link首锚bow anchor尾锚stern anchor有杆锚/海军锚stocked anchor锚铃环anchor ring锚干anchor shank锚爪anchor fluke锚冠anchor crown锚爪臂anchor arm锚尖anchor bill锚爪掌anchor flukepalm锚杆销forelock pin横杆folding stock无杆锚/山字锚stockless anchor锚卸扣anchor shackle锚肩/助抓突角anchor shoulder销轴pintle横销pin cotter大抓力锚high holding power anchor 普通链环common link加大链环enlarged link末端链环end open link散合式连接链环detachable link肯特卸扣Kenter link转环swivel link电动锚机electric windlass电动液压锚机hydraulic windlass电动机electromotor减速器reducer传动齿轮drive gear离合器clutch链轮chain wheel刹车操纵杆brake control rod带缆卷筒rope drum带式刹车brake绞盘capstan锚机间windlass room锚链末端bitter end舾装数/船具数N/equipment number 备锚spare anchor大抓力锚HHP超大抓力锚SHHP挂锚hanging off an anchor单花cross双花elbow锚链绞缠foul hawse清解锚链cleaning a foul hawse力链riding cable惰链sleeping cable保险缆safety line挂缆hang line送出缆removing rope纤维缆绳fibre rope钢丝缆绳wire rope尼龙绳nylon rope涤纶绳polyester rope丙纶绳polypropylene乙纶绳polyethylene维尼龙绳vinylon rope硬钢丝绳stiff wire rope半硬钢丝绳semi-flexible wire rope软钢丝绳flexible wire rope钢丝股strand油麻芯股jute heart钢丝wire油麻芯jute or wire core复合缆compound rope破断强度breaking load/BL安全强度safety load安全工作负荷safe working load/SWL试验强度test strength/TS验证负荷proof load/PL头缆/首缆head line尾缆stern line前横缆forward breast line后横缆aft breast line前倒缆/首倒缆fore spring line后倒缆aft spring line单头缆buoy line回头缆slip line吊拖leading ahead巴拿马导缆孔Panama fairlead缆桩bitt/bollard导向滚轮pedestal fairlead万向导缆孔multi-angled fairlead导向滚轮guide roller单十字缆桩single cross bitt羊角桩cleat单柱系缆桩single-post bitt双柱系缆桩double-post bitt斜式双柱系缆桩double raked bitt双十字缆桩double cross bitt导缆孔chock导向滚柱fairlead roller导缆钳fairleader转动导缆器/万向导缆器universal fairlead 水平滚柱horizontal roller垂直滚柱vertical roller基座seating卷筒cable drum挡角horn基座pedestal绞缆机/系缆绞车mooring winch系缆绞盘capstan圆盘刹车disc brake主卷筒main drum减速箱reduction gear box联轴节union joint主轴main shaft滚筒capstan head检查盖inspection cover控制开关control switch接线盒terminal box自动张力绞缆机automatic tension mooring winch 压力调节阀pressure adjusting valve液压泵hydraulic pump卷筒/缆车reel制缆索stopper撇缆绳heaving line撇缆头heaving line ball碰垫/靠把fender防鼠板rat guard撇缆器throwing line apparatus靠泊berthing离泊unberthing乔塞尔公式Joessel平板舵/单板舵single-plate rudder流线型舵streamline rudder舵杆rudder stock连接法兰coupling flange舵臂rudder stay舵板rudder plate舵销rudder pin水平加强筋horizontal stiffener焊接衬板welding bracket垂直加强筋vertical stiffener吊舵孔lifting rudder tube不平衡舵unbalanced rudder平衡舵balanced rudder半平衡舵semi-balanced rudder支承舵bearing rudder多支承舵multi-pintle rudder双支承舵double bearing rudder穿心舵轴平衡舵balanced rudder with axle 悬挂舵underhung rudder半悬挂舵partially underhung rudder反应舵/迎流舵reaction rudder主动舵active rudder整流帽舵bulb rudder襟翼舵flettner rudder/flap rudder科特导流管舵Kort nozzle rudder组合舵unit rudder希林舵Schilling rudder舵叶rudder blade固定导流管fixed nozzle可转动导流管movable nozzle翼片fin螺旋桨舵rudder propeller水平法兰连接horizontal coupling joint垂直法兰连接vertical coupling joint上轴承upper bearing舵轴rudder axle下轴承lower bearing吊舵孔tube hole骨架肋板webs舵底塞drain plug舵板rudder plate衬套cylinder liner止推滚珠轴承non-return ball bearing舵承体rudder bearing frame填料packing舵承盖rudder bearer cover挡板shield水密填料watertight packing螺钉screw舵杆衬套stock bushing本体rudder body压盖screw cover滚珠轴承ball bearing底座bed plate蜗杆worm蜗轮worm wheel小齿轮small gear舵扇rudder quadrant缓冲弹簧buffer spring舵柄tiller液缸hydraulic cylinder柱塞ram滑块cod piece动力装置PU/power units换向阀CO/changeover valve溢流阀RV/relief valve锁紧阀LV/locking valve阀门箱VC/valve chest伺服控制SC/servo control辅助泵auxiliary pump固定体/定子stator回转体/转子rotor动叶movable vane压力舱室pressure chamber定叶fixed vane油管路manifold储油箱oil tank舵角限位器rudder angle stopper随动系统follow-up system手柄控制系统/直接控制系统/应急控制系统non-follow-up system 舵轮wheel液缸liquid tank活塞piston轴axle齿条gear rank弹簧spring活塞杆piston lever杠杆lever液压管路hydraulic pipe自动操舵装置控制系统automatic course-keeping control system 自动舵autopilot比例旋钮/舵角调节旋钮rudder adjust微分旋钮/反舵角调节旋钮/速率调节rate adjust灵敏度旋钮/天气调节旋钮/航摆角调节weather adjust航摆角yawing自动改向旋钮course adjust自适应舵adaptive autopilot恒向线rhumb line自动驾驶仪/航迹舵automatic navigation综合导航仪integrated NA V system航路数据routeing data微处理器micro-processing计程仪Log speed船舶动态vessel movement显示器display警报系统alarm system选择开关select switch舵角反馈器rudder angle feedback计划航线navigation plan计划航向predetermined course大圆航法great circle滑车block挂头oval eye车壳steel side plate车带tail strop制动板stopping plate轴spindle滑轮cast-iron sheave车尾tail绞辘tackle辘绳tackle-fall力端running end根端standing end定滑车fixed block动滑车movable block卸扣shackle钩hook眼板eye plate眼环ring plate心环thimble紧索夹/绳头卸扣clamp索头环socket/swaged terminal松紧螺丝扣/花篮螺丝rigging screw起重机/克令吊crane控制室cabin变幅/旋转操纵杆control lever for slewing/luffing 起货操纵杆control lever for hoisting吊臂jib油马达oil motor上油柜head tank过滤器oil strainer冷却器oil cooler限位器箱differential limit switch box变幅绞车luffing winch起货绞车hoisting winch吊货滑车falling block液压千斤顶hydraulic cylinder安全工作负荷safe working load/SWL吊货索cargo fall千斤索topping lift起货机cargo winch千斤索绞车topping lift winch吊杆boom吊货钩cargo hook起重柱Samson post/SP双杆联合union purchase舷内吊杆/大关inside boom舷外吊杆/小关outside boom调整稳索adjustable guy保险稳索insurance guy三角眼板triangle eye-plate吊货索滑车组cargo fall tackle千斤索滑车组topping lift tackle稳索guy导向滑车leading block桅柱mast重型吊杆heavy derrick控制台cross-tree轻型吊杆derrick山字吊货钩Flemish hook连接横杆connecting traverse拉索pull guy滚动式rolling type滚翻式rolling and tipping type舱口围板支架brackets偏心轮eccentric wheel连接链connecting chain上滚轮upper roller压紧器cleat halve上升轨wheel ramp导装面板leading panel折叠式folding type铰链slotted hinge固定钩fixed hook存放臂stowing arm钢索wire pendant铰接滑车hinged sheave拖拽眼板hauling eye plate关闭臂closing arm固定钩securing hook熏舱fumigation《货物系固手册》cargo securing manual/CSM 货物单元cargo unit标准货standardized cargo半标准货semi-standardized cargo非标准货non-standardized cargo货物系固设备cargo securing device系固secure支持support最大系固负荷maximum securing load/MSL 固定式系固设备fixed securing device便携式系固设备portable securing device地铃lashing eye系固链条lashing chain紧链器tension lever钢丝绳lashing wire rope系固钢带lashing steel band花篮螺丝/松紧螺旋扣turnbuckle系固槽座lashing pot绑扎带lashing band象脚elephant feet拖车支架trailer trestle拖车千斤顶trailer support jack轮楔wheel chock系固钢丝lashing wire快速释放紧索器quick release lashing底座foundation滑移底座sliding foundation埋入式底座imbed foundation燕尾槽/燕尾底座dovetail foundation板式底座doubling plate foundation插座socket固定锥welding cone可折地铃/D形环D-ring眼板lashing plate箱格导轨系统cellguide system横撑材transverse prop导箱构件container guide member横向支撑底座lateral support foundation集装箱绑扎桥lashing bridge扭锁twistlock操作杆operating rod半自动扭锁semi-automatic twistlock锁销locking pin底座扭锁bottom twistlock堆锥stacking cone中间堆锥inter-bridge stacking cone底座堆锥bottom stacking cone可移动锥板removable cone plate自动定位锥automatic fixing cone锁紧装置locking device调整堆锥/高度补偿锥leveling stacking cone桥锁bridge fitting绑扎杆/绑扎棒lashing bar横向撑柱lateral support element辅助工具accessory appliance分舱因数factor of subdivision重心gravity/G稳心metacenter/M船舶修理ship repair计划修理planned repair临时修理occasional repair航修voyage repair小修current repair岁修annual repair检修overhaul船坞dock坞修dock repair事故修理accident repair自修self repair防腐锌板ZINC protector/anticorrosion zinc plate进坞图docking plan舵结构图rudder construction plan浮坞floating dock船底望光light measure with eye for the bottom deforming 裂缝crack止裂孔stopper hole船舶修理单repair list缺陷清单defect list外观检查external examination内部检查internal examination缺陷修补imperfection mend系泊试验docking test密性试验watertight test冲水试验hose testing压水试验water test气密试验gastight test舷梯gangway航行与信号设备navigation and signal equipment通信设备communication equipment倾斜试验inclining test航行试验navigation test加强检验附加标志ESP/Enhanced Survey Program水下检验in-water survey压载水管理计划BWMP/ballast water management plan 入级检验classification survey保持船级检验survey for class maintenance年度检验annual survey中间检验intermediate survey坞内检验docking survey特别检验special survey循环检验continuous survey法定检验statutory survey营运中检验survey for ships in service定期检验periodical survey换证检验change certificate survey附加检验additional survey。
船舶英语报验表
Pipes fitting in the tanksBW tanksFPT 艏尖舱NO.1 B.S.W.B TK (P) 1号底边压载水舱（左）NO.1 B.S.W.B TK (S) 1号底边压载水舱（右）NO.2 B.S.W.B TK (P) 2号底边压载水舱（左）NO.2 B.S.W.B TK (S) 2号底边压载水舱（右）NO.3 B.S.W.B TK (P) 3号底边压载水舱（左）NO.3 B.S.W.B TK (S) 3号底边压载水舱（右）NO.4 B.S.W.B TK (P) 4号底边压载水舱（左）NO.4 B.S.W.B TK (S) 4 号底边压载水舱（右）NO.5 B.S.W.B TK (P) 5号底边压载水舱（左）NO.5 B.S.W.B TK (S) 5号底边压载水舱（右）NO.1 T.S.W.B TK (P) 1号顶边压载水舱（左）NO.1 T.S.W.B TK (S) 1号顶边压载水舱（右）NO.2 T.S.W.B TK (P) 2号顶边压载水舱（左）NO.2 T.S.W.B TK (S) 2号顶边压载水舱（右）NO.3 T.S.W.B TK (P) 3号顶边压载水舱（左）NO.3 T.S.W.B TK (S) 3号顶边压载水舱（右）NO.3 C.H/W.B TK 3号货仓/压载水舱APT 艉尖舱HFO tanksNO.1 HFO TK(P) 1号燃油舱（左）NO.1 HFO TK(S) 1号燃油舱（右）NO.2 HFO TK(P) 2号燃油舱（左）NO.2 HFO TK(S) 2号燃油舱（右）NO.3 HFO TK(P) 3号燃油舱（左）NO.3 HFO TK(S) 3号燃油舱（右）NO.1 HFO SERV TK 1号燃油日用舱NO.2 HFO SERV TK 2号燃油日用舱NO.1 HFO SETT TK 1号燃油沉清舱NO.2 HFO SETT TK 2号燃油沉清舱MDO tanksNO.1 MDO TK 1号柴油舱NO.2 MDO TK 2号柴油舱NO.3 MDO TK 3号柴油舱NO.1 MDO SERV TK 1号柴油日用舱NO.2 MDO SERV TK 2号柴油日用舱EG MDO D TK 应发柴油日用柜MDO TK FOR INCINERATOR 焚烧炉柴油柜CO tanksNO.1 CYL.OIL 1号汽缸油储存舱NO.2 CYL.OIL 2号汽缸油储存舱NO.1 CLY.OIL MEASURING TK 1号汽缸油测量柜NO.2 CLY.OIL MEASURING TK 2号汽缸油测量柜LO tanksM/E LO 主机滑油储存舱M/E LO SETT. TK 主机滑油沉清舱G/E LO 辅机滑油储存舱G/E LO 辅机滑油沉清舱M/E LO SUMP TK 主机滑油循环舱FW tanksFW TK (P) 淡水舱（左）FW TK(S) 淡水舱（右）DISTILLED 蒸馏水舱Other tanks and sea chests 艉管冷却水舱F.W. WASHING TK 洗舱水舱SLOPE/SEWAGE WASHING TK 洗舱污水/生活污水舱SLUDGE TK 油渣舱BILGE HOLD TK 舱底水存放舱F.O OVERF. TK 燃油溢流舱F.O DRAIN TK 燃油泄放舱WASTE OIL TK 废油舱S/T LO. DRAIN TK 艉管滑油泄放舱SEWAGE TK 生活污水舱CHAIN LOCKER TK ( P) 锚链舱(左）CHAIN LOCKER TK ( S) 锚链舱(右）STERN TUBE LO GRAITY TK 艉管滑油重力油柜STEERING GRAR STORAGE OIL Tk 舵机储油箱M/E SCAVENGE BOX DRAIN TK 主机扫气箱泄放柜CHEMECAL CLEANING TK ME 主机化学清洗柜ALARM DEVICE BOX 报警装置箱M/E JACKET FW.EXPANSION TK 主机缸套水膨胀水箱LT FRESH WATER EXPANSION TK 低温水膨胀水箱Low Sea Chest 低位海底门High Sea Chest 高位海底门Emer. Sea Chest 应急海底门Tanks tightness testBW tanksFPT 艏尖舱NO.1 B.S.W.B TK (P) 1号底边压载水舱（左）NO.1 B.S.W.B TK (S) 1号底边压载水舱（右）NO.2 B.S.W.B TK (P) 2号底边压载水舱（左）NO.2 B.S.W.B TK (S) 2号底边压载水舱（右）NO.3 B.S.W.B TK (P) 3号底边压载水舱（左）NO.3 B.S.W.B TK (S) 3号底边压载水舱（右）NO.4 B.S.W.B TK (P) 4号底边压载水舱（左）NO.4 B.S.W.B TK (S) 4 号底边压载水舱（右）NO.5 B.S.W.B TK (P) 5号底边压载水舱（左）NO.5 B.S.W.B TK (S) 5号底边压载水舱（右）NO.1 T.S.W.B TK (P) 1号顶边压载水舱（左）NO.1 T.S.W.B TK (S) 1号顶边压载水舱（右）NO.2 T.S.W.B TK (P) 2号顶边压载水舱（左）NO.2 T.S.W.B TK (S) 2号顶边压载水舱（右）NO.3 T.S.W.B TK (P) 3号顶边压载水舱（左）NO.3 T.S.W.B TK (S) 3号顶边压载水舱（右）APT 艉尖舱HFO tanksNO.1 HFO TK(P) 1号燃油舱（左）NO.1 HFO TK(S) 1号燃油舱（右）NO.2 HFO TK(P) 2号燃油舱（左）NO.2 HFO TK(S) 2号燃油舱（右）NO.3 HFO TK(P) 3号燃油舱（左）NO.3 HFO TK(S) 3号燃油舱（右）NO.1 HFO SERV TK 1号燃油日用舱NO.2 HFO SERV TK 2号燃油日用舱NO.1 HFO SETT TK 1号燃油沉清舱NO.2 HFO SETT TK 2号燃油沉清舱MDO tanksNO.1 MDO TK 1号柴油舱NO.2 MDO TK 2号柴油舱NO.3 MDO TK 3号柴油舱NO.1 MDO SERV TK 1号柴油日用舱NO.2 MDO SERV TK 2号柴油日用舱EG MDO D TK 应发柴油日用柜MDO TK FOR INCINERATOR 焚烧炉柴油柜CO tanksNO.1 CYL.OIL 1号汽缸油储存舱NO.2 CYL.OIL 2号汽缸油储存舱NO.1 CLY.OIL MEASURING TK 1号汽缸油测量柜NO.2 CLY.OIL MEASURING TK 2号汽缸油测量柜LO tanksM/E LO 主机滑油储存舱M/E LO SETT. TK 主机滑油沉清舱G/E LO 辅机滑油储存舱G/E LO 辅机滑油沉清舱M/E LO SUMP TK 主机滑油循环舱FW tanksFW TK (P) 淡水舱（左）FW TK(S) 淡水舱（右）DISTILLED 蒸馏水舱Other tanks and sea chests 艉管冷却水舱F.W. WASHING TK 洗舱水舱SLOPE/SEWAGE WASHING TK 洗舱污水/生活污水舱SLUDGE TK 油渣舱BILGE HOLD TK 舱底水存放舱F.O OVERF. TK 燃油溢流舱F.O DRAIN TK 燃油泄放舱WASTE OIL TK 废油舱S/T LO. DRAIN TK 艉管滑油泄放舱SEWAGE TK 生活污水舱CHAIN LOCKER TK ( P) 锚链舱(左）CHAIN LOCKER TK ( S) 锚链舱(右）STERN TUBE LO GRAITY TK 艉管滑油重力油柜STEERING GRAR STORAGE OIL Tk 舵机储油箱DE-AERATING TK 高温淡水除气筒M/E SCAVENGE BOX DRAIN TK 主机扫气箱泄放柜CHEMECAL CLEANING TK ME 主机化学清洗柜M/E JACKET FW.EXPANSION TK 主机缸套水膨胀水箱LT FRESH WATER EXPANSION TK 低温水膨胀水箱Low Sea Chest 低位海底门High Sea Chest 高位海底门Emer. Sea Chest 应急海底门Tightness before launchingoverboard discharge valves 排舷外阀ICCP 外加电流阴极保护Speed log and echo sounder 计程仪和测深仪Installlation of systems and electrical equipmentPiping systems installation & tightnessMDO systemMDO transfer pipe system in ER 机舱柴油驳运管系"MDO daily system of ME, AE ,EG, steam boiler 柴油日用管系" MDO separating system 柴油净化管系Overflow pipes of MDO TKS and MDO TK FOR INCINERATOR 柴油沉清舱及焚烧炉柴油柜的溢流管系HFO systemHFO transfer system in ER 机舱燃油驳运管系HFO transfer system Fr 35 Fore 货仓燃油驳运管系"HFO daily system of ME, AE, steam boiler 燃油日用管系"HFO separating system 燃油净化管系Overflow pipes of HFO SETT TKS and NO.3 HFO TK 燃油沉清舱及3#燃油舱的溢流管系LO systemLO deck filling systems of ME and AE 主辅机甲板滑油注入管系LO daily circulating system of ME 主机滑油日用管系LO separating system of ME and AE 主辅机滑油净化管系LO service system of sterntube 艉管滑油日用管系CO systemCO deck filling system 甲板汽缸油注入管系CO system of ME 主机汽缸油管系FO and LO drainage systemFO drainage system 燃柴油泄放系统LO drainage system 滑油泄放系统Hydr oil systemfree fall boat hydr oil system 抛落艇液压管系steer gear hydr oil system (only check installation) 舵机液压管系(只看安装）windlass hydro.system in forecastle 首部锚绞机液压油管.winch hydro.system in aft. 尾部绞机液压油管.hydro. Oil system for H/C hydro. Power pack1 ？hydro. Oil system for H/C hydro. Power pack2 ?hydro. Oil filling pipes for four deck cranes ?hydro. Oil pipes for all H/C cylinders ?Cooling water sytemMain sea water pipe 主海水管系Sea water cooling system 海水冷却管系Sea water piping system of fresh water generator 造水机的海水管系ME HT cooling water system 主机高温冷却水管系ME/AE LT cooling water system 主辅机低温冷却水管系Compressed air systemsStarting air system of ME 主机启动空气Starting air system of AE 辅机启动空气Control air system in ER 机舱控制空气Air system of air horn 汽笛空气管系Working air system in ER including air reducing station pipes 机舱杂用空气及减压阀组管系Working air system on superstructure 上建杂用空气管系Fr 35 Fore working air system 货仓杂用空气管系quick closing valves system 快关阀空气管系deck washing and Fire-fighting piping systemsSuperstructure 上建ER 机舱Fr 35 Fore 货仓主甲板mist water fire figthing system in ER 机舱水雾喷淋CO2 piping systemCO2 release system in ER 机舱CO2 释放管系CO2 release system Fr 35 Fore 货仓CO2 释放管系CO2 control pipes CO2 控制管CO2 release pipes for galley 厨房CO2 释放管系CO2 release pipes for painting store room 油漆间CO2 释放管系Water supply system ( cold/hot water)ER 机舱Superstructure 上建Ballast & bilge piping systemER 机舱区域Fr 35 Fore 货舱区域steam and central heating systemsboiler feed water 锅炉给水系统steam and condensate system in ER 机舱蒸汽冷凝系统steam and condensate system in pipe tunnel 管弄蒸汽冷凝系统steam heat tracing system 蒸汽伴行管Heating coil pipesNO.1 HFO TK(P) 1号燃油舱（左）NO.1 HFO TK(S) 1号燃油舱（右）NO.2 HFO TK(P) 2号燃油舱（左）NO.2 HFO TK(S) 2号燃油舱（右）NO.3 HFO TK(P) 3号燃油舱（左）NO.3 HFO TK(S) 3号燃油舱（右）NO.1 HFO SERV TK 1号燃油日用舱NO.2 HFO SERV TK 2号燃油日用舱NO.1 HFO SETT TK 1号燃油沉清舱NO.2 HFO SETT TK 2号燃油沉清舱SLUDGE TK 油渣舱ME LO 主机滑油沉清舱AE LO 辅机滑油沉清舱ME LO SUMP TK 主机滑油循环舱F.O OVERFLOW TK 燃油溢流舱BILGE HOLD TK 舱底水存放舱WASTE OIL TK 废油舱F.O DRAIN TK 燃油泄放舱CHEMICAL CLEANING TK 化学清洗柜ME SCAVENG DRAIN TK 主机扫气箱泄放柜bilge water separator pipes and sludge dischargebilge water separator pipes 舱底油水分离器管系sludge discharge pipes 油渣排舷外管系O2 and C2H2 pipes to workshopO2 and C2H2 pipes to workshop 氧气乙炔去机修间管系Black water & gray water pipesSuperstructure 上建区域ER 机舱区域Cleaning system of main engine scav. Air coolerchemical cleaning system of MEAC and cold store refrigerating systemsAC refrigerating copper pipes cleaning 空调制冷铜管清洁AC refrigerating installation and pressure test 空调制冷铜管安装及密性AC refrigerating vacuum test 空调制冷铜管抽真空Cold store refrigerating copper pipes cleaning 冷库制冷铜管清洁Cold store refrigerating installation and pressure test 冷库制冷铜管安装及密性Cold store refrigerating vacuum test 冷库制冷铜管抽真空A/C duct and mechanical ventilation systemA / C spiral ducts and mechanical vent pipes insuperstructure cabines 上建各房间空调螺旋通风管和机械通风管安装"mechanical vent ducts in ER, CO2 room,steering gear room, purifier room, workshop etc. 机舱，CO2室等房间机械通风管安装"remote control pipes(two core tube) of remote control valvesremote control pipes(two core tube) of remote control valves 遥控阀多芯管Exhaust pipesInstallation of exhaust pipesAE 发电机EG 应发steam boiler 蒸汽锅炉ME 主机Water drain pipes"superstructure, main deck and forecastle 上建，主甲板，艏部"ER 机舱ER oil & water tanks vent pipesER oil & water tanks vent pipes 机舱各油&水舱透气管安装及密性Electrical systems and equipment installationCable trays"Forecastle boatswain's store room, deck store room,carpenter room,paint room etc. 艏部水手长储藏室，甲板储藏室，木工间，油漆间等"main deck hatchcoaming PS and SB 主甲板舱口围左右舷Inside of all cargo hold transverse walkways 货仓内梯道Pipe tunnel 管弄A deck to compass deck A甲板到罗经甲板Engine room 机舱Cables layout"Forecastle boatswain's store room, deck store room,carpenter room,paint room etc. 艏部水手长储藏室，甲板储藏室，木工间，油漆间等"main deck hatchcoaming PS and SB 主甲板舱口围左右舷Inside of all cargo hold transverse walkways 货仓内梯道Pipe tunnel 管弄A deck to compass deck A甲板到罗经甲板Engine room 机舱Cables penetration"Forecastle boatswain's store room, deck store room,carpenter room,paint room etc. 艏部水手长储藏室，甲板储藏室，木工间，油漆间等"main deck hatchcoaming PS and SB 主甲板舱口围左右舷Inside of all cargo hold transverse walkways 货仓内梯道Pipe tunnel 管弄A deck to compass deck A甲板到罗经甲板Engine room 机舱Cables glandsForecastle deck 艏楼甲板main deck hatch coaming PS and SB 主甲板舱口围左右舷Outside superstructure 上建室外Engine room 机舱Pipe tunnel 管弄Inside cargo hold 货仓内部Main electrical equipment installation and cleanessMain switchboard 主配电板Emergency switchboard 应急配电板Engine control console 集控台Wheel house console 驾控台Flushing/Blowing of systems and cleaness of tanksSystems flushing/blowing/cleaningMDO/HFO"HFO&MDO daily system of ME, AE , steam boiler 燃柴油日用系统 "HFO&MDO separating system 燃柴油净化管系LOLO deck filling systems of ME and AE 主辅机甲板滑油注入管系LO daily circulating system of ME 主机滑油日用管系LO separating system of ME and AE 主辅机滑油净化管系LO service system of sterntube 艉管滑油日用管系Hydr oilfree fall boat hydr oil system 抛落艇液压管系steer gear hydr oil system 舵机液压管系windlass hydro.system in forecastle 首部锚绞机液压油管.winch hydro.system in aft. 尾部绞机液压油管.hydro. Oil system for H/C hydro. Power pack1 ？hydro. Oil system for H/C hydro. Power pack2 ？hydro. Oil filling pipes for four deck cranes ？hydro. Oil pipes for all H/C cylinders ？CO systemCO deck filling system 甲板汽缸油注入管系CO system of ME 主机汽缸油管系Cooling waterHT cooling water system 高温冷却水管系LT cooling water system 低温冷却水管系HT cooling water sample analyze after chemical added 高温冷却水加药后取样LT cooling water sample analyze after chemical added 低温冷却水加药后取样Air systemsStarting air system of ME 主机启动空气Starting air system of AE 发电机启动空气CO2CO2 release system in ER 机舱CO2释放管系CO2 release system Fr.35 Fore 货仓CO2释放管系"Steam, feed water and central heating"boiler feed water system including hotwell 锅炉给水管系及热井boiler feed water sample analyze after chemical added 锅炉给水加药后取样steam and condensate system 蒸汽冷凝管系O2 and C2H2 pipes to workshopO2 and C2H2 pipes to workshop 氧乙炔管系Tanks cleanness and blind free inspection before closing manholesHFO tanks cleanness and blind free inspectionNO.1 HFO TK(P) 1号燃油舱（左）NO.1 HFO TK(S) 1号燃油舱（右）NO.2 HFO TK(P) 2号燃油舱（左）NO.2 HFO TK(S) 2号燃油舱（右）NO.3 HFO TK(P) 3号燃油舱（左）NO.3 HFO TK(S) 3号燃油舱（右）NO.1 HFO SERV TK 1号燃油日用舱NO.2 HFO SERV TK 2号燃油日用舱NO.1 HFO SETT TK 1号燃油沉清舱NO.2 HFO SETT TK 2号燃油沉清舱MDO tanks cleanness and blind free inspectionNO.1 MDO TK 1号柴油舱NO.2 MDO TK 2号柴油舱NO.3 MDO TK 3号柴油舱NO.1 MDO SERV TK 1号柴油日用舱NO.2 MDO SERV TK 2号柴油日用舱EG MDO D TK 应发柴油日用柜MDO TK FOR INCINERATOR 焚烧炉柴油柜LO tanks cleanness blind free inspectionM/E LO 主机滑油储存舱M/E LO SETT. TK 主机滑油沉清舱G/E LO 辅机滑油储存舱G/E LO 辅机滑油沉清舱M/E LO SUMP TK 主机滑油循环舱CO tanks cleanness blind free inspectionNO.1 CYL.OIL 1号汽缸油储存舱NO.2 CYL.OIL 2号汽缸油储存舱NO.1 CLY.OIL MEASURING TK 1号汽缸油测量柜NO.2 CLY.OIL MEASURING TK 2号汽缸油测量柜FW tanks cleanness blind free inspectionFW TK (P) 淡水舱（左）FW TK(S) 淡水舱（右）DISTILLED 蒸馏水舱Other tanks cleanness blind free inspection 艉管冷却水舱F.W. WASHING TK 洗舱水舱SLOPE/SEWAGE WASHING TK 洗舱污水/生活污水舱SLUDGE TK 油渣舱BILGE HOLD TK 舱底水存放舱F.O OVERF. TK 燃油溢流舱F.O DRAIN TK 燃油泄放舱WASTE OIL TK 废油舱S/T LO. DRAIN TK 艉管滑油泄放舱SEWAGE TK 生活污水舱CHAIN LOCKER TK ( P) 锚链舱(左）CHAIN LOCKER TK ( S) 锚链舱(右）STERN TUBE LO GRAITY TK 艉管滑油重力油柜STEERING GRAR STORAGE OIL Tk 舵机储油箱M/E SCAVENGE BOX DRAIN TK 主机扫气箱泄放柜CHEMECAL CLEANING TK ME 主机化学清洗柜M/E JACKET FW.EXPANSION TK 主机缸套水膨胀水箱LT FRESH WATER EXPANSION TK 低温水膨胀水箱Main Propulsion and Rudder installationPropeller shaft and rudder center line alignmentER area construction Fr.35 after and under main deck are finishedME foundation are prealignedME foundation are weldedPropeller shaft and rudder center line alignment by steel wireME foundation all through bolt holes drilled"Stern tube, propeller shaft , blades installation "Cleaning stern tube before fixing stern tube outsideRudder system installationbearing sleeves 2 pcs rudder stock workshop"ME shifting, superstructure shifting and reaming shaft coupling/ ME fly wheel fitting bolts holes "flat bars to be welded inside ME foundation for chockfast"ME alignment, installations , shaft jack up test , shaft earth device etc."dynamic measurement before shaft alignmentAE/EG installationAE 1 chock fitting and foundation bolts tighten 1#发电机垫块安装及螺栓扳紧AE 2 chock fitting and foundation bolts tighten 2#发电机垫块安装及螺栓扳紧AE 3 chock fitting and foundation bolts tighten 3#发电机垫块安装及螺栓扳紧EG chock fitting and foundation bolts tighten 应急发电机垫块安装及螺栓扳紧Deck equipment installationWindlass foundation pouring chockfast and bolts tighten 锚机底座浇环氧及螺栓扳紧Winches foundation pouring chockfast and bolts tighten 绞车底座浇环氧及螺栓扳紧"Trial, Alarms and Other Tests"EG function testalarm points of EG 应发报警点load test 应发负荷AE function test"alarm points of AE1, AE2, AE3 1#，2#，3# 发电机报警点"load test of Aes 1#，2#，3# 发电机负荷parallel run test of main generators 主发并车"MSB, ESB and shore connection box"protection devices and equipment of MSB 主配电板保护protection devices and equipment of ESB 应急配电板保护protection of shore connection box 岸电保护24 V auto battery charge/discharge panelalarm points 报警点charge and discharge test 充电和放电试验Steam boilerSteam boiler boiling out(cleaning chamber) 蒸汽锅炉煮炉（清洁炉室）Steam boiler alarm points 蒸汽锅炉报警点boiler feed water pumps 锅炉给水泵dosing pump for steam boiler 锅炉加药泵Steam boiler functon test on MDO 锅炉烧柴油试验Steam boiler functon test on HFO 锅炉烧重油试验Engine room equipments/pumps teststeering gear 舵机"HFO, LO separators 燃油滑油分油机"incinerator 焚烧炉engine room fans 机舱风机"main air compressors ， service air compressor, emergency air compressor;main air reservoir,contrlo air reservoir，service air reservoir,emerg.air reservoir 主空压机,甲板日用空压机，应急空压机；主空气瓶，控制空气瓶,甲板日用空气瓶，应急空气瓶"control air dehydrator 控制空气干燥器air reducing station 减压阀组SW cooling pumps 海水冷却水泵LT CW main and harbour pumps 低温冷却水泵及停港冷却水泵M/E jacket F.W cooling pumps 主机缸套水冷却水泵"FW hydrophor, FW pumps , UV lamp 淡水压力柜，淡水压力泵紫外线消毒器""TW hydrophor , TW pump 技术水压力柜技术水泵 ""calorifier, hot water circulating pumps 热水柜，热水循环泵"LO transfer pump 滑油输送泵stern tube LO pump 艉管滑油泵CYC. Oil transfer pump 汽缸油输送泵sludge pump including dry running protection 油渣泵包括防干磨保护oily water separator 油水分离器sewage treatment plant including sewage discharge pump 污水处理装置包括污水排放泵ER crane function and load test 机舱行车效用及负荷试验cold store refrigerating plant function test including cooling effective test 冷库制冷单元效用及冷库制冷试验"emergency stop test for FO, LO pumps and fans 风油切断"FW generator test and F.W mineralizing unit (sea trial) 造水机及矿化滤器ME air cooler chemical cleaning pump 主机空冷器化学清洗泵electrical test panel 电工实验板Workshops equipment testsgas welding 气焊elec. Welding 电焊grinding machine 砂轮机drilling machine 钻床lathe machine 车床grinding machine for exh.valve 排气阀研磨机M/E fuel valve test device 主机喷油器试验装置Systems of whole vessel function testspiping system with pump function testsbilge water system for whole vessel including pumps and ejectors 全船舱底水效用包括泵浦及喷射泵ballast system including pumps and stripping ejectors 压载水效用包括泵浦及扫舱喷射泵 fire fighting system for whole vessel including pumps 全船消防效用及泵浦water mist fire extinguishing system in ER including pump unit 机舱水雾喷淋效用及泵浦单元steam heating system for ER tanks 机舱舱室蒸汽加热系统steam heating system for HFO storage tanks 货仓燃油储存舱蒸汽加热系统steam heat tracing system 蒸汽伴行系统效用HFO and MDO transfering system test including pumps 燃、柴油驳运效用及泵浦FW hot / cold and TW supply system in superstructure 上建供水FW hot / cold and TW supply system in ER 机舱供水"drain pipes in superstructure ,main deck,forecastle deck 上建，主甲板，首部疏排水系统""drain pipes of FO drain ,LO drain and water drain in ER 机舱燃油，滑油水泄放""air supply system for ER, main deck and forecastle 全船杂用空气效用"remote control valves system 遥控阀系统remote level measuring system + manual sounding 液位遥测系统+ 手动测深quick closing valve systems function test 快关阀系统效用"CO2 system for whole vessel(ER, CH，galley，painting store) 全船CO2效用"cargo hold smoke detection 货仓烟雾探测bridge windows washing system including wipers 驾驶室雨刮器效用sea chests P/S function test of the valves 左右海底门遥控阀效用Ventilation systems in whole vessel incl fans"ER and ER other spaces ventilation including fans, flaps etc 机舱及机舱内其他区域通风包括风机，风闸""superstructure ventilation including fans, flaps etc 上建通风包括风机风闸""cargo hold ventilation including fans, flaps etc 货仓通风包括风机，风闸"AC system in accomodationAC plant test 中央空调AC system in accomodation effective test 上建风量测试air condition system for galley 厨房空调air condition system for ECR 集控室空调Level alarms and temperature alarmsHFO and MDO tanksHFO tks (Tk01-03)high level 燃油舱1-3#舱液位高MDO tanks high level (TK01-03) 柴油舱1-3#液位高FO overflow tank level high(ER) 燃油溢流舱液位高NO.1 HFO SETT TK level high 1#燃油沉清舱液位高NO.2 HFO SETT TK level high 2#燃油沉清舱液位高NO.1 HFO SERV TK level low 1#燃油日用舱液位低NO.2 HFO SERV TK level low 2#燃油日用舱液位低NO.1 MDO SERV TK level low 1#柴油日用舱液位低NO.2 MDO SERV TK level low 2#柴油日用舱液位低HFO tanks (TK01-03) temperature high 燃油舱1-3# 温度高NO.1 HFO SETT TK temperature high 1#燃油沉清舱温度高NO.2 HFO SETT TK temperature high 2#燃油沉清舱温度高NO.1 HFO SERV TK temperature high 1#燃油日用舱温度高NO.2 HFO SERV TK temperature high 2#燃油日用舱温度高MDO SERV tank for emergency generator level low 应发柴油柜液位低INCIN. M.D.O. TK. Low level 焚烧炉柴油柜液位低LO and CO tanksLO sump Tank ME level low 主机滑油循环舱液位低LO stern tube head tank level low 艉管滑油重力柜液位低LO stern tube forward seal tank level low 艉管艏密封柜液位低LO stern tube forward seal tank level high 艉管艏密封柜液位高LO stern tube after seal tank level low 艉管艉密封柜液位低LO stern tube after seal tank level high 艉管艉密封柜液位高LO stern tube DRAIN TK.level low 艉管滑油泄放舱液位低No.1 M/E CYL. OIL MEASUR. TK. Level low 1#主机汽缸油测量柜液位低No.2 M/E CYL. OIL MEASUR. TK. Level low 2#主机汽缸油测量柜液位低Bilge wellsBilge well in cargo hold 5 SB level high No.5货舱污水井液位高(右)Bilge well in cargo hold 5 PS level high No.5货舱污水井液位高(左)Bilge well in cargo hold 4 AFT. SB level high No.4货舱污水井液位(后右)Bilge well in cargo hold 4 AFT. PS level high No.4货舱污水井液位(后左)Bilge well in cargo hold 4 FWD. SB level high No.4货舱污水井液位(前右)Bilge well in cargo hold 4 FWD. PS level high No.4货舱污水井液位(前左)Bilge well in cargo hold 3 SB level high No.3货舱污水井液位高(右)Bilge well in cargo hold 3 PS level high No.3货舱污水井液位高(左) Bilge well in cargo hold 2 AFT.SB level high No.2货舱污水井液位高(后右) Bilge well in cargo hold 2 AFT.PS level high No.2货舱污水井液位高(后左) Bilge well in cargo hold 2 FWD.SB level high No.2货舱污水井液位高(前右) Bilge well in cargo hold 2 FWD.PS level high No.2货舱污水井液位高(前左) Bilge well in cargo hold 1 SB level high No.1货舱污水井液位高(右)Bilge well in cargo hold 1 PS level high No.1货舱污水井液位高(左)Bilge well in boatswain store SB level high 水手长储藏室污水井液位高（右）Bilge well in boatswain store PS level high 水手长储藏室污水井液位高（左）Bilge well in windlass control room level high 锚机控制室液位高Bilge well in carpenter room level high 木工间液位高Bilge well in painting room level high 油漆间液位高Bilge well in FORE. VOID SB level high 首空仓液位高（右）Bilge well in FORE. VOID PS level high 首空仓液位高（左）Bilge well in LOG&SOUND room level high 计程仪测深仪室液位高Bilge water in pipe tunnel level high 管弄舱底水液位高Bilge water level in emergency fire pump room level high 应急消防泵舱舱底水液位高Bilge well in engine room FWD. PS level high 机舱前污水井左舷液位高Bilge well in engine room FWD. SB level high 机舱前污水井右舷液位高Bilge well in engine room AFT. Level high 机舱尾部污水井液位高Bilge well beneath M/E level high 主机座下污水井液位高ER tanksM/E J.F W. EXP. TK. Level low 主机缸套水膨胀水箱液位低LT FCW expansion tank level low 低温冷却水膨胀水箱液位低M/E H.T.F.W. AL.device box level low 主机缸套水报警装置液位低waste oil tank level high 废油舱液位高sludge oil tank level high 油渣舱液位高FO. Drain TK level high 燃油泄放舱液位高FRESH W. TK. Level low (P) 淡水舱左舷液位低INCIN. WASTE TK. Level high 焚烧炉废油柜液位高BILGE HOLD. TK.level high 舱底水存放舱液位高SEWAGE TK. (BLACK W.) level high 生活污水舱液位高ballast water tanksmanual sounding pipes function test for all ballast water tanks 所有压载舱手动测试效用Main propulsion system mooring testME alarm points 主机报警点ME pre-heating unit 主机预热单元ME turning gear 主机盘车机ME FO booster unit 供油单元ME LO auto. Filter 主机滑油自清滤器ME LO sump 主机滑油泵shaft earthing device 轴接地装置ME mooring test 主机系泊试验ME turbocharger cleaning system (sea trials) 主机涡轮增压器清洗Accomodation equipment testgalley equipment 厨房设备laundry equipment 洗衣间设备Deck equipment and outfittings testsbunker hose crane 油管吊Anchor abandoning test 弃锚试验deck cranes function and load test 甲板克令吊效用及负荷试验provision crane function and load test 杂物吊效用及负荷试验accommodation ladders function and load test 舷梯效用及负荷试验Pilot ladder 引水员软梯rescue boat davit 救助艇架rescue boat 救助艇free fall boat 抛落艇free fall boat davit 抛落艇架mooring winches 系泊绞车anchor windlasses 锚机H/C hydro. Power pack1 舱盖液压单元"doors, windows and small hatchcovers"operating test 开关试验host test 冲水试验dead weight measurement 空船称重Electrical systemselectrical space heaters for whole vesselelectrical space heater in sanitary units 卫生单元电加热器electrical space heater in store rooms 甲板储藏室电加热器Lightingsnormal and emergency lightingsuperstructure open deck 上建室外superstructure accomodation 上建室内ER and service spaces 机舱及机舱其他服务场所"main deck and forecastle including deck cranes, power pack rooms, store room, etc 主甲板，艏部包括克令吊，液压单元室，甲板储藏室等等"cargo holds 货仓pipe tunnel 管弄nautical lightingnavigation and signal lights 航行灯和信号灯suez searching light 苏伊士搜救灯Suez Canal light socket 苏伊士运河灯插座daytime signal searching light 白昼信号搜索灯panama Canal steering light 巴拿马运河操舵灯anti-fouling and cathodic protection systems 防海生物及外加电流阴极保护"Communication, indication, signalling equipment & alarm systems"fire/smoke detection system alarm 火警及烟雾探测bunker station alarm / telephone 加油站报警、电话water ingress alarm sysytem 货仓进水报警系统cold store room call 冷库误锁hospital call 病房呼叫general alarm system 通用报警E/R telegraph 机舱车种automatic telephone 自动电话sound power telephone 声力电话E/R column alarms 机舱灯柱报警talk back system 对讲public address system 广播Community antenna device 天线共用器master clock test 子母钟open/close indicators for WT doors and small covers. 水密门及小舱盖开闭指示fog horn 雾笛nautical radio & communication equipmentEcho-sounder 回声测深仪speed log 计程仪Gyro-compass 电罗经automatic pilot 自动操舵仪Radar &responder 雷达及雷达应答器D-GPS D-GPS 导航仪VHF radiophone VHF 无线电话VDR 航行数据记录仪SATCOM C / SATCOM F 卫星通讯系统C站，F站DSC 数字选呼电话设备EPIRB 应急无线电示位标SSAS 防海盗系统Network systems and computersLoading computer 装载计算机Ships network system 船舶网络系统AIS-system 船舶状态识别系统Seatrials。
船舶驾驶员实用英语口语审批稿
船舶驾驶员实用英语口语YKK standardization office【 YKK5AB- YKK08- YKK2C- YKK18】Lesson ThreeTug Assistance: 拖带协助Dialog A: Tug Ordering对话1：叫拖船Yong Men/BOCV: Avonport Port Control. This is M/V Yong Men. I amanchor at Lambs Roadstead. I require tugs. Over. “永门”船：爱汶港调度，我是“永门”船。
我在莱姆斯港外开敞锚地抛锚。
我需要拖船，请讲。
Avonport : Roger. How many tugs do you require? Over.爱汶港口调度：信息已清楚。
你需要多少拖船？请讲。
Yong Men/BOCV: I will order two tugs. When will tugs expect to meetme? Over.“永门”船：我要两艘拖船，拖船几点到，请讲。
Avonport : The tugs expect to meet you in half an hour. Out.爱汶港口调度：拖船半小时内到，完毕。
Dialog B: Tug Operation对话2：拖船在工作M/V Eternal Glory: Hold on your towing line. Make fast please. Forwardtug. Over.“永恒光荣”船：请拉紧拖缆，绑牢，前拖船。
请讲。
Forward tug: M/V Eternal Glory. This is tug forward. The current istoo rough. I suggest the aft tug single up. Over. 前拖船：“永恒光荣”船，这是前拖船。
水流太不平稳了，我建议后面的拖船单绑，请讲。
船舶专用英语汇总
船舶专业英文词汇No.1船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇来自：navigation > 《ship》上一篇：船舶保安员工作要点下一篇：海洋运输常用英文缩略语转藏到我的图书馆献花(1) 分享到微信以文找文分享：人人网开心网搜狐微博推荐给朋友举报类似文章更多•船舶专业英语词汇•船体制图常用英中名词术语对照•船舶英语(页1) - 设计学习- 千岛热线论....•船体结构英语•船舶英语手册1--5•Navis.gr - 3Examination Questions For...•船舶图纸符号大全•货运保险鉴定常用词汇。
海上通讯实用英语审批稿
海上通讯实用英语 YKK standardization office【 YKK5AB- YKK08- YKK2C- YKK18】吴淞VTS实用英语汇编一、基础部分字母拼读spelling of letters数字拼读spelling of numbersPlease use IMO Standard Marine Communication Phrases 请使用《IMO标准航海通信用语》I will use IMO Standard Marine Communication Phrases 我将使用《IMO标准航海通信用语》MAYDAY用于发布遇险信文。
PAN-PAN用于发布紧急信文。
SECURITE用于发布安全信文。
数字Numbers数字逐位读出应读作：“一五零”；“One-five-zero”应读作：“二点五”“Two decimal five” or “Two point five”术语 GLOSSARY弃船Abandon vessel漂移Adrift水面高度Air draft风向逆转Backing( of wind)盲区Blind sector登轮船速Boarding speed平舱机Bob-cat倾覆Capsize (to)方位浮标Cardinal buoy基点(罗经点) Cardinal points伤亡Casualty货物相容性Compatibility限于吃水的船舶Vessel constrained by her draft航向Course推算航迹向Course made good原油洗舱COW Crude Oil Washing最近会遇点/最近会遇时间CPA/TCPA紧急停车Crash-stop破损控制队Damage control team丧失航行能力Disabled离船Disembark吃水Draught or draft走锚Dragging (of anchor)拖锚Dredging (of anchor )漂流Drifting进水Flooding (海水不受控制地大量涌入船舶)缠锚Foul (of anchor)缠螺旋桨Foul (of propeller)让路Give away操纵能力受到限制的船Hampered vessel初始航向Initial course抛弃货物Jettison (to) (of cargo)泄漏Leaking下风Leeward偏航Leeway横倾List进水Make water to（船舶由于船壳损坏或舱口受海浪冲击及未关妥而造成海水涌入）应变部署表Muster list失控Not under command受限区域Restricted area点名Roll call安全航速Safe speed货物隔票Segregation (of goods)货物横移Shifting cargo溢油Spill风向顺转Veering (of winds)锚松出Veer out (to) (of anchor)倒出锚链Walk out (to)(of anchor)上风windward二、通用部分实用语句和短句：一）、动态报告Movement ReportsM/V:WUSONG VTS, we are passing CJK reporting line，my position is bearing 60 degrees, distance 2 nautical miles from CJK light vessel，over.吴淞交管中心，我船刚过长江口报告线，我的船位距长江口灯船方位60度，距离2海里处,请回答。
船舶常用英语(一)汇总
一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船第 1 页共24 页cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳. 专业.专注.hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长. 专业.专注.length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）. 专业.专注.bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器. 专业.专注.camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔. 专业.专注.duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟. 专业.专注.gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨. 专业.专注.keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板. 专业.专注.out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航. 专业.专注.sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算. 专业.专注.strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门. 专业.专注.weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料) T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力. 专业.专注.elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲. 专业.专注.lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差. 专业.专注.building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验. 专业.专注.pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度. 专业.专注.potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复. 专业.专注.12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start)不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammable vapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴. 专业.专注.4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲. 专业.专注.22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损. 专业.专注.7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热. 专业.专注.9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀. 专业.专注.14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊. 专业.专注.。
船舶常用英语汇总
General arrangement 总布置Interior arrangement 舱室布置Engine room arrangement 机舱布置Compass deck 罗经甲板Navigation deck, bridge deck 驾驶甲板Boat deck 艇甲板Promenade deck 游步甲板Accommodation deck 起居甲板Helicopter deck 直升机甲板Upper deck 上甲板Winch platform 起货机平台Passage , passage way 通道Wheel house 驾驶室Chart room 海图室Radio room 报务室Radar room 雷达室Engine room 机舱Centralized control room for machineries 机舱集控室Reactor room 反应堆舱Boiler room 锅炉舱Pump room 泵舱Chain locker 锚链舱Steering engine room, steering gear room 舵机舱Fan room 通风机室Air conditioning unit room 空调机室Refrigerator room 冷冻机室Fire-smothering unit room 灭火装置室Emergency generator room 应急发电机室Commutator room 变流机室Battery room 蓄电池室Gyro-compass room 陀螺罗经室Mast room 桅室Sonar transducer space 声纳舱Log room 计程仪舱CO2 room CO 2室Paint room 油漆间Lamp room 灯具间Windlass room 起锚机室Anchor winch, anchor windlass 起锚机Mooring winch 拖缆机，系泊绞车Accommodation 起居舱室Cabin 居住舱室Captain’s room 船长室Crew’s room 船员室Passenger cabin 客舱Chief engineer officer’s room 轮机长室Engineer’s room 轮机员室1st officer’s room, chief officer’s room 大副室2nd officer’s room 二副室1st engineer officer’s room 大管轮室2nd engineer officer’s room 二管轮室Galley 厨房Mess 餐厅Smoking room 吸烟室Hospital 医务室Changing room 更衣室Game room 娱乐室Water closet (WC) 卫生间Bath room 浴室Washing room, laundry 洗衣间Dry room 烘干间Cargo hold, cargo space 货舱Cargo oil tank 货油舱Container hold 集装箱船Refrigerated cargo hold 冷藏货舱Liquified natural gas tank 液化天然气舱Liquefied petroleum gas tank 液化石油气舱Mail room 邮件舱Luggage room 行李舱Liquid tank 液舱Fuel oil tank 燃油舱Lubricant oil tank 滑油舱Overflow oil tank 溢油舱Dirty oil tank 污油舱Ballast water tank 压载水舱Fresh water tank 淡水舱Drinking water tank 饮水舱Feed water tank 锅炉水舱Light diesel oil tank, marine diesel oil tank 轻柴油舱Heavy diesel oil tank 重柴油舱Heavy fuel oil tank 重油舱Fuel oil daily tank, fuel oil service tank 日用燃油舱（柜）Settling tank 沉淀舱Sludge tank 油渣舱Circulating lub oil tank 循环油舱Double bottom tank 双层底舱Void 空舱Bilge tank 污水舱Slop tank 污油水舱Store 贮藏室Hawser store 帆缆间Fore peak 艏尖舱After peak 尾尖舱Bottom side tank 底边舱Top side tank 顶边舱Wing tank 边舱Hold 底舱Deep tank 深舱Tween deck cargo space 甲板间舱Cofferdam 空隔舱Molded hull surface 船体型表面Hull form 船体线型Bare hull, naked hull 裸船体Molded volume 型排水体积（任一水面下，船舶裸船体所排开的水的体积）Appendages 附体（水线以下突出于船体型表面以外的物体，包括轴包套、艉轴架、轴、舵、螺旋桨、舭龙骨、方龙骨、减摇鳍、导流罩等，但不包括外板在内）Principle particulars 主要要素Principle coordinate planes 主坐标平面Base plane 基平面Center line plane 中线面Mid station plane 中站面Base line 基线Principle dimensions 主尺度Length overall 总长Extreme length 最大长Length between perpendiculars 垂线间长Waterline length 水线长Designed waterline length 设计水线长Load waterline length 满载水线长Molded breadth 型宽Waterline breadth 水线宽Extreme breadth 最大宽Molded depth 型深Draft 吃水Molded draft 型吃水Designed draft 设计吃水Fore draft 艏吃水After draft 艉吃水Mean draft 平均吃水Navigational draft 外形吃水Loaded draft 满载吃水Draft mark 吃水标志Lines plan 型线图Forward perpendiculars 艏垂线After perpendiculars 艉垂线Grid 格子线Ordinate station 站（在型线图中，沿基线将垂线间长或设计水线长分成若干间距的各点，及其在半宽水线图上沿中线面的相应投影点。
船舶常用英语汇总
General arrangement 总布置Interior arrangement 舱室布置Engine room arrangement 机舱布置Compass deck 罗经甲板Navigation deck, bridge deck 驾驶甲板Boat deck 艇甲板Promenade deck 游步甲板Accommodation deck 起居甲板Helicopter deck 直升机甲板Upper deck 上甲板Winch platform 起货机平台Passage , passage way 通道Wheel house 驾驶室Chart room 海图室Radio room 报务室Radar room 雷达室Engine room 机舱Centralized control room for machineries 机舱集控室Reactor room 反应堆舱Boiler room 锅炉舱Pump room 泵舱Chain locker 锚链舱Steering engine room, steering gear room 舵机舱Fan room 通风机室Air conditioning unit room 空调机室Refrigerator room 冷冻机室Fire-smothering unit room 灭火装置室Emergency generator room 应急发电机室Commutator room 变流机室Battery room 蓄电池室Gyro-compass room 陀螺罗经室Mast room 桅室Sonar transducer space 声纳舱Log room 计程仪舱CO2 room CO 2室Paint room 油漆间Lamp room 灯具间Windlass room 起锚机室Anchor winch, anchor windlass 起锚机Mooring winch 拖缆机，系泊绞车Accommodation 起居舱室Cabin 居住舱室Captain’s room 船长室Crew’s room 船员室Passenger cabin 客舱Chief engineer officer’s room 轮机长室Engineer’s room 轮机员室1st officer’s room, chief officer’s room 大副室2nd officer’s room 二副室1st engineer officer’s room 大管轮室2nd engineer officer’s room 二管轮室Galley 厨房Mess 餐厅Smoking room 吸烟室Hospital 医务室Changing room 更衣室Game room 娱乐室Water closet (WC) 卫生间Bath room 浴室Washing room, laundry 洗衣间Dry room 烘干间Cargo hold, cargo space 货舱Cargo oil tank 货油舱Container hold 集装箱船Refrigerated cargo hold 冷藏货舱Liquified natural gas tank 液化天然气舱Liquefied petroleum gas tank 液化石油气舱Mail room 邮件舱Luggage room 行李舱Liquid tank 液舱Fuel oil tank 燃油舱Lubricant oil tank 滑油舱Overflow oil tank 溢油舱Dirty oil tank 污油舱Ballast water tank 压载水舱Fresh water tank 淡水舱Drinking water tank 饮水舱Feed water tank 锅炉水舱Light diesel oil tank, marine diesel oil tank 轻柴油舱Heavy diesel oil tank 重柴油舱Heavy fuel oil tank 重油舱Fuel oil daily tank, fuel oil service tank 日用燃油舱（柜）Settling tank 沉淀舱Sludge tank 油渣舱Circulating lub oil tank 循环油舱Double bottom tank 双层底舱Void 空舱Bilge tank 污水舱Slop tank 污油水舱Store 贮藏室Hawser store 帆缆间Fore peak 艏尖舱After peak 尾尖舱Bottom side tank 底边舱Top side tank 顶边舱Wing tank 边舱Hold 底舱Deep tank 深舱Tween deck cargo space 甲板间舱Cofferdam 空隔舱Molded hull surface 船体型表面Hull form 船体线型Bare hull, naked hull 裸船体Molded volume 型排水体积（任一水面下，船舶裸船体所排开的水的体积）Appendages 附体（水线以下突出于船体型表面以外的物体，包括轴包套、艉轴架、轴、舵、螺旋桨、舭龙骨、方龙骨、减摇鳍、导流罩等，但不包括外板在内）Principle particulars 主要要素Principle coordinate planes 主坐标平面Base plane 基平面Center line plane 中线面Mid station plane 中站面Base line 基线Principle dimensions 主尺度Length overall 总长Extreme length 最大长Length between perpendiculars 垂线间长Waterline length 水线长Designed waterline length 设计水线长Load waterline length 满载水线长Molded breadth 型宽Waterline breadth 水线宽Extreme breadth 最大宽Molded depth 型深Draft 吃水Molded draft 型吃水Designed draft 设计吃水Fore draft 艏吃水After draft 艉吃水Mean draft 平均吃水Navigational draft 外形吃水Loaded draft 满载吃水Draft mark 吃水标志Lines plan 型线图Forward perpendiculars 艏垂线After perpendiculars 艉垂线Grid 格子线Ordinate station 站（在型线图中，沿基线将垂线间长或设计水线长分成若干间距的各点，及其在半宽水线图上沿中线面的相应投影点。
船舶常用英语(一)
船舶常用英语(一)一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan舢板, 小船manpowered boat人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushioncraft 气垫船hydrofoil水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelledship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck shipVLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship(RO/RO ship) 滚装船ferry渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler拖网渔轮barge carrier; lighteraboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth;depth) 登记长度（宽度、深度）freeboard干舷rise of floor (dead; rise) 舭高；船底loadlinemark载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder舷梯accommodation ladder platform 舷梯平台accommodation laddermanrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast压载（物）ballast line压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt系缆桩bollard 系缆桩；系船柱；双系柱bolster枕垫bonnet烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater挡浪板bridge桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank燃料舱bushing衬套butt端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever悬臂梁capstan绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming围板；舱口围板cofferdam隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit吊艇架；吊艇柱deck甲板deck beam 甲板横梁deckhouse甲板室deck line甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick吊杆diaphragm隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange折边flanged bracket 折边肘板flat keel 平板龙骨floor肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation底座frame肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating格子板；滑铁板ground tackle 锚泊索具gunwale舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser绳索；大缆heel踵材；横倾hinged cover(door) 铰链盖（门）hold货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel龙骨keelblock龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson内龙骨kingpost起重柱；将军柱knee肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framingsystem 纵骨架式longitudinal strength 纵向强度lug耳板main deck 主甲板main frame 主肋骨manhole人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer防挠振纵桁pillar支柱；墩pintle舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform平台plating壳板plimsoll mark 载重线标志poop艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking（船体）横向挠度rail扶手；栏杆rolling横摇round of beam梁拱round stern 圆（船）尾rudder舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop扇形开孔scantling构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam焊缝；接缝section剖面section modulus剖面模数semi-balanced rudder半平衡舵shaft轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage;trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer舷弧；偏航sheer strake 舷顶列板shell船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid护舷木；垫板skylight天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot槽；开缝sluice水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem艏；艏柱；艏材stem post 艏柱stern船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool托架，座，凳strake列板strength calculation 强度计算strength deck 强力甲板stringer纵桁stringer plate 甲板边板structural member 构件structural strength结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion扭转torsion strength 扭转强度transom stern 方形船尾transverse横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool上（下）托架ventilator通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge楔木，楔子winch起货机winch-head绞车卷筒windlass起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material(造船材料)T-bar T型钢Z-bar Z型钢I-Bar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuildingworkmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语第 31 页共 45 页angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination;第 32 页共 45 页list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim第 33 页共 45 页纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition情况良好2.in poor condition情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglectedcondition 缺乏保养5.not properly serviced未经正常保养6.not properly cleaned未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted未经正常校正10.defective 有缺陷的（失效）11.damaged损坏damaged beyondrepair 损坏了无法修复12.failed (in failure)第 34 页共 45 页失效13.cut of order (in trouble)故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless)不能使用（指必须换新的损坏部件）19.could not bestarted(failed to start)不能启动20.empty 空的21.fitted incorrectly安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerousaccumulation ofinflammable vapors可燃气体危险集积it was obvious that this state had existedfor a considerable time（损坏）状况是长期存在的23.sluggish in (action,answering) （动作、应答）迟钝B.Deficiencies1.no…fitted,no…provided 未第 35 页共 45 页装2.no…available未备有3.missing遗失4.incomplete 不齐全，不完整5.deficient不足，缺少6.insufficient不足7.neglected遗漏8.omitted遗漏，省去9.removed移开，拆走10.washed overboard冲走11.dropped跌落12.fitted with wrong ….(size, material,devices…)错用（尺寸，材料，仪器）C.Tightness, stains, lossof etc.1.Leaking漏2.infiltrating (seeping)渗漏3.weeping泪滴4.sweating汗滴5.not watertight不水密6.loss of watertightness失去水密性（比5好）7.loss of airtightness失去气密性8.loss of oiltightness失去油密性9.escaping of cool逃冷第 36 页共 45 页10.loss of lub-oil pressure滑油压力降低11.loss of water pressure水压力降低12.oil polluted油污染13.oil soaked油浸14.water soaked水浸15.water stained水渍16.oil stained油渍17.rust in patches锈斑18.verdigris in patches铜绿斑19.water marks水渍D.Crack, score, breaketc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕第 37 页共 45 页9.chapped龟裂，折裂10.fractured折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed穿洞13.holed & flooded破洞浸水14.opened开口15.bent弯曲16.canted倾斜17.buckled皱折18.warped翘起，翘曲19.indented (dented)凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured毁损27.torn off撕破torn拉脱28.pierced刺破29.peeled 剥皮（油第 38 页共 45 页漆剥落）30.burst 爆破（指高压管路）31.blown off (packing)吹脱32.distorted 扭曲，歪扭33.engine break-down因故障机器突然停车E.Corrosion, seizing,choking etc.1.corrosion腐蚀2.wasted耗油3.deteriorated蚀薄4.thinned变薄5.pitted麻点6.eroded侵蚀7.rusted生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged老化12. seized咬住13. seized by corrosion锈死14. stuck （粘）咬住15. rust-jammed锈轧16. fouled拥塞17. clogged堵塞（常指管子的堵塞）18. blocked第 39 页共 45 页阻塞19. gagged塞口20. foul & dirty闭塞21. blanked封没22. plugged闭塞23. choked 卡住，阻塞F.Wear, loose, clearanceetc.1.Loose松动2.starting（铆钉）松动3.slack松动slack back松出4.worn磨损5.worn cut evenly均匀磨损6.worn cut unevenly不均匀磨损7.worn on one side单边磨损8.worn outsymmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung（铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance间隙过大13.excess backlash齿隙过大14.excess vibration振动过大15.excess noise level噪音过大第 40 页共 45 页16.loose engagement啮合太松17.loose connection接头松动18.tooth齿worn out 磨损chopped off 崩缺fractured折断19.knocking敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal轴承合金detached脱壳cracked开裂wiped铺铅belted熔化oil groove blocked 油槽堵塞21.out off roundness失圆22.out off alignment拉线不直23.off-centering偏心24.deflected偏斜G.Burning, heating, etc.1.Sparking火花2.arcking (arcing)电弧mutator第 41 页共 45 页整流器scored拉痕burnt烧坏worn 磨耗，磨损uneven不平sparking火花blackened发黑rough粗糙mica undercut弧坑4.brush set incorrectly碳刷安装不正确5.scorched烤焦6.coked结焦7.charred结碳8.overheated过热9.broken down击穿10. short-circuit短路11. setting incorrect 整定值不正确12. tripped incorrect脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged未充满overcharged充电过量dry water水干A. Remove, crop etc.1.Removed第 42 页共 45 页拆下2.removed & replaced拆装3.removed, faired &replaced拆装拷平4.cropped & renewed割换（管、板、栏杆）5.partly renewed部分换新6.partly cropped &renewed 部分割换7.cut off割除8.faired拷平9.faired on原地拷平10.faired in place原地拷平11.straightened拷直、校直12.dismantle 拆卸（某一零件）13.disassembled拆散（解体）14.stripped 拆除（某一部件）15.unshipped拆下16.disconnected 断开（线、管接头）17.opened打开18.lifted抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with)换用21.patch贴补B.Fit, scrape, grind etc.1.fitted & scraped拂刮2.fitted & ground拂磨第 43 页共 45 页3.scraped & ground刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round磨圆7.ground smooth磨光8.ground & reamed磨绞9.bored round镗圆10.planed smooth刨光11.polished抛光12.machined光车13.skimmed光刀14.finish machined精加工15.rough machine粗加工C.Re-metal, adjust,check etc1.Remetalled重浇白合金2.re-babbitted重浇白合金（专指巴氏合金）3.pulled out拉出4.drawn out抽出5.taken out取出6.adjusted调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance第 44 页共 45 页校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped拷锈（油漆）11.measured & recorded测量并记录12.logged (hourly)记录（小时）D.weld, rivet, wind etc.1.repaired by welding电焊修理2.welded补焊、焊接3.closed up by welds（面积、深度、高度较大）焊补4.built up by welds堆焊5.plug welded塞焊6.spot welded点焊7.butt welded对接焊8 tackweld 点焊、平头焊、定位焊第 45 页共 45 页。
船舶常用英语(一)汇总
船舶常用英语(一)汇总一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan舢板, 小船manpowered boat人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushioncraft 气垫船hydrofoil水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelledship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck shipcargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-containership 全集装箱船semi-containership 半集装箱船multi-purposecontainer ship 多用途集装箱船general cargo ship/vessel/carrier杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber)carrier运木船cattle carrier 运牲畜船multi-purpose ship多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship(RO/RO ship) 滚装船ferry渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth;depth) 登记长度（宽度、深度）freeboard干舷rise of floor (dead; rise) 舭高；船底loadlinemark载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder舷梯accommodation ladder platform 舷梯平台accommodation laddermanrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt系缆桩bollard 系缆桩；系船柱；双系柱bolster枕垫bonnet烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器第 11 页共 46 页bracket 肘板；（三角）拖架breakwater挡浪板bridge桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark舷墙bulwark plating 舷墙板bulwark stay舷墙扶强材bunker tank 燃料舱bushing衬套butt端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber翘曲camber of beam 梁拱第 12 页共 46 页cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever悬臂梁capstan绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming围板；舱口围板cofferdam隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁第 13 页共 46 页companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit吊艇架；吊艇柱deck甲板deck beam 甲板横梁deckhouse甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick吊杆diaphragm隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫第 14 页共 46 页dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate面板fender碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange折边flanged bracket 折边肘板flat keel 平板龙骨floor肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱第 15 页共 46 页forward perpendicular 首垂线foundation底座frame肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating格子板；滑铁板ground tackle 锚泊索具gunwale舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）第 16 页共 46 页handrail舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser绳索；大缆heel踵材；横倾hinged cover(door) 铰链盖（门）hold货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱第 17 页共 46 页hold stringer 舱内纵桁hopper漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel龙骨keelblock龙骨墩keel line 龙骨线；艏艉线keel plate第 18 页共 46 页龙骨板keel rail （救生艇）艇底把手keelson内龙骨kingpost起重柱；将军柱knee肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug耳板main deck 主甲板main frame 主肋骨manhole人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽第 19 页共 46 页molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam防挠振梁panting stringer 防挠振纵桁pillar支柱；墩pintle舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform平台plating壳板第 20 页共 46 页plimsoll mark 载重线标志poop艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking（船体）横向挠度rail扶手；栏杆rolling横摇round of beam 梁拱round stern 圆（船）尾rudder舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop扇形开孔scantling构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam焊缝；接缝section剖面section modulus 剖面模数semi-balanced rudder半平衡舵shaft轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage;trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer舷弧；偏航sheer strake 舷顶列板shell船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid护舷木；垫板skylight天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot槽；开缝sluice水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe测量管；测深管stabilizer减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem艏；艏柱；艏材stem post 艏柱stern船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool托架，座，凳strake列板strength calculation 强度计算strength deck 强力甲板stringer纵桁stringer plate 甲板边板structural member构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion扭转torsion strength 扭转强度transom stern 方形船尾transverse横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate上（下）支架板upper (lower) stool 上（下）托架ventilator通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge楔木，楔子winch起货机winch-head绞车卷筒windlass起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material(造船材料)T-bar T型钢Z-bar Z型钢I-Bar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuildingworkmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination;list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition情况良好2.in poor condition情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglectedcondition 缺乏保养5.not properly serviced未经正常保养6.not properly cleaned未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted未经正常校正10.defective 有缺陷的（失效）11.damaged损坏damaged beyondrepair 损坏了无法修复12.failed (in failure)失效13.cut of order (in trouble)故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless)不能使用（指必须换新的损坏部件）19.could not bestarted(failed to start)不能启动20.empty 空的21.fitted incorrectly安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerousaccumulation ofinflammable vapors可燃气体危险集积it was obvious that this state had existedfor a considerable time（损坏）状况是长期存在的23.sluggish in (action,answering) （动作、应答）迟钝B.Deficiencies1.no…fitted,no…provided 未装2.no…available未备有3.missing遗失4.incomplete 不齐全，不完整5.deficient不足，缺少6.insufficient不足7.neglected遗漏8.omitted遗漏，省去9.removed移开，拆走10.washed overboard冲走11.dropped跌落12.fitted with wrong ….(size, material,devices…)错用（尺寸，材料，仪器）C.Tightness, stains, lossof etc.1.Leaking漏2.infiltrating (seeping)渗漏3.weeping泪滴4.sweating汗滴5.not watertight不水密6.loss of watertightness失去水密性（比5好）7.loss of airtightness失去气密性8.loss of oiltightness失去油密性9.escaping of cool逃冷10.loss of lub-oil pressure滑油压力降低11.loss of water pressure水压力降低12.oil polluted油污染13.oil soaked油浸14.water soaked水浸15.water stained水渍16.oil stained油渍17.rust in patches锈斑18.verdigris in patches铜绿斑19.water marks水渍D.Crack, score, breaketc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped龟裂，折裂10.fractured折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed穿洞13.holed & flooded破洞浸水14.opened开口15.bent弯曲16.canted倾斜17.buckled皱折18.warped翘起，翘曲19.indented (dented)凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured毁损27.torn off撕破torn拉脱28.pierced刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing)吹脱32.distorted 扭曲，歪扭33.engine break-down因故障机器突然停车E.Corrosion, seizing,choking etc.1.corrosion腐蚀2.wasted耗油3.deteriorated蚀薄4.thinned变薄5.pitted麻点6.eroded侵蚀7.rusted生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged老化12. seized咬住13. seized by corrosion锈死14. stuck （粘）咬住15. rust-jammed锈轧16. fouled拥塞17. clogged堵塞（常指管子的堵塞）18. blocked阻塞19. gagged塞口20. foul & dirty闭塞21. blanked封没22. plugged闭塞23. choked 卡住，阻塞F.Wear, loose, clearanceetc.1.Loose松动2.starting（铆钉）松动3.slack松动slack back松出4.worn磨损5.worn cut evenly均匀磨损6.worn cut unevenly不均匀磨损7.worn on one side单边磨损8.worn outsymmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung（铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance间隙过大13.excess backlash齿隙过大14.excess vibration振动过大15.excess noise level噪音过大16.loose engagement啮合太松17.loose connection接头松动18.tooth齿worn out 磨损chopped off 崩缺fractured折断19.knocking敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal轴承合金detached脱壳cracked开裂wiped铺铅belted熔化oil groove blocked 油槽堵塞21.out off roundness失圆22.out off alignment拉线不直23.off-centering偏心24.deflected偏斜G.Burning, heating, etc.1.Sparking火花2.arcking (arcing)第 41 页共 46 页电弧mutator整流器scored拉痕burnt烧坏worn 磨耗，磨损uneven不平sparking火花blackened发黑rough粗糙mica undercut弧坑4.brush set incorrectly碳刷安装不正确5.scorched烤焦6.coked结焦7.charred结碳8.overheated过热9.broken down击穿10. short-circuit短路11. setting incorrect 整定值不正确12. tripped incorrect脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged未充满overcharged充电过量dry water水干第 42 页共 46 页A. Remove, crop etc.1.Removed拆下2.removed & replaced拆装3.removed, faired &replaced拆装拷平4.cropped & renewed割换（管、板、栏杆）5.partly renewed部分换新6.partly cropped &renewed 部分割换7.cut off割除8.faired拷平9.faired on原地拷平10.faired in place原地拷平11.straightened拷直、校直12.dismantle 拆卸（某一零件）13.disassembled拆散（解体）14.stripped 拆除（某一部件）15.unshipped拆下16.disconnected 断开（线、管接头）17.opened打开18.lifted抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with)换用21.patch贴补B.Fit, scrape, grind etc.1.fitted & scraped拂刮第 43 页共 46 页2.fitted & ground拂磨3.scraped & ground刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round磨圆7.ground smooth磨光8.ground & reamed磨绞9.bored round镗圆10.planed smooth刨光11.polished抛光12.machined光车13.skimmed光刀14.finish machined精加工15.rough machine粗加工C.Re-metal, adjust,check etc1.Remetalled重浇白合金2.re-babbitted重浇白合金（专指巴氏合金）3.pulled out拉出4.drawn out抽出5.taken out取出6.adjusted调整，校正adjusted for alignment 校正拉线adjusted true第 44 页共 46 页校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped拷锈（油漆）11.measured & recorded测量并记录12.logged (hourly)记录（小时）D.weld, rivet, wind etc.1.repaired by welding电焊修理2.welded补焊、焊接3.closed up by welds（面积、深度、高度较大）焊补4.built up by welds堆焊5.plug welded塞焊6.spot welded点焊7.butt welded对接焊第 45 页共 46 页8 tackweld 点焊、平头焊、定位焊第 46 页共 46 页。
船舶专用英语汇总
船舶专业英文词汇No.1船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇来自：navigation > 《ship》上一篇：船舶保安员工作要点下一篇：海洋运输常用英文缩略语转藏到我的图书馆献花(1) 分享到微信以文找文分享：人人网开心网搜狐微博推荐给朋友举报类似文章更多∙船舶专业英语词汇∙船体制图常用英中名词术语对照∙船舶英语(页1) - 设计学习- 千岛热线论....∙船体结构英语∙船舶英语手册1--5.word可编辑.∙Navis.gr - 3Examination Questions For...∙船舶图纸符号大全∙货运保险鉴定常用词汇. 专业.专注.。
船舶英文演讲稿范文
Good morning/afternoon/evening, and welcome to this distinguished gathering. It is an honor to stand before you today to discuss a subject that has been integral to the world’s economy and trade for centuries: the maritime industry and the role of ships in our global community.As we stand on the deck of this magnificent vessel, surrounded by the vast expanse of the ocean, it is impossible not to feel a profound sense of awe and appreciation for the ships that have braved the waves since time immemorial. The ship, a marvel of human ingenuity, has been the backbone of international trade, exploration, and cultural exchange.The maritime industry is not just about the vessels that traverse the seas; it is a complex ecosystem that involves the seafarers, shipbuilders, port authorities, and countless others who contribute to the smooth operation of this vital sector. Today, I would like to highlight some key aspects of the maritime industry and the importance of ships in our interconnected world.Firstly, the ship is the silent carrier of goods and services across the globe. Whether it is the raw materials needed for manufacturing, the food we consume, or the clothes we wear, ships ensure that these items reach us efficiently and in good condition. The maritime industry is responsible for transporting approximately 90% of the world’s cargo, making it the lifeblood of international trade.Secondly, ships are not just commercial vehicles; they are also platforms for exploration and discovery. The age of exploration, which began in the 15th century, was made possible by the development of the ship. It was through the daring voyages of explorers like Columbus, Magellan, and Cook that we discovered new lands, seas, and cultures. Today, ships continue to push the boundaries of our knowledge, carrying scientists, researchers, and adventurers to the most remote corners of the world.Thirdly, ships are a symbol of unity and cooperation. The maritime industry is governed by a set of international regulations and agreements, such as the International Maritime Organization (IMO) conventions, which ensure the safety, security, and environmentalprotection of shipping activities. These regulations require collaboration between nations, companies, and individuals, fostering a spirit of global unity and shared responsibility.However, it is important to acknowledge the challenges that the maritime industry faces. Environmental concerns, such as pollution and climate change, pose significant threats to the health of our oceans and the sustainability of the industry. The shipping industry is also facing economic challenges, including rising fuel costs and the need to adapt to new technologies.In response to these challenges, the maritime industry is taking proactive steps to reduce its environmental impact. Alternative fuels, such as liquefied natural gas (LNG), are being explored to decrease emissions. Additionally, innovations in ship design and navigation are being implemented to optimize fuel efficiency and reduce waste.In conclusion, the ship is a testament to human ingenuity and the indomitable spirit of exploration. It is a vital link in the global supply chain, a symbol of unity, and a beacon of hope for future generations. As we look to the future, let us remember the legacy of the ship and the role it plays in shaping our world.I would like to leave you with a few thoughts:1. The maritime industry must continue to innovate and adapt to meet the challenges of the 21st century.2. We must prioritize the protection of our oceans and the environment for the benefit of all.3. The spirit of exploration and unity must be at the heart of our efforts to ensure a sustainable and prosperous future for the maritime industry.Thank you for your attention, and may the sea be ever kind to us all.[Your Name]。
船舶英语报验表
船舶英语报验表Pipes fitting in the tanksBW tanksFPT 艏尖舱NO.1 B.S.W.B TK (P) 1号底边压载水舱（左）NO.1 B.S.W.B TK (S) 1号底边压载水舱（右）NO.2 B.S.W.B TK (P) 2号底边压载水舱（左）NO.2 B.S.W.B TK (S) 2号底边压载水舱（右）NO.3 B.S.W.B TK (P) 3号底边压载水舱（左）NO.3 B.S.W.B TK (S) 3号底边压载水舱（右）NO.4 B.S.W.B TK (P) 4号底边压载水舱（左）NO.4 B.S.W.B TK (S) 4 号底边压载水舱（右）NO.5 B.S.W.B TK (P) 5号底边压载水舱（左）NO.5 B.S.W.B TK (S) 5号底边压载水舱（右）NO.1 T.S.W.B TK (P) 1号顶边压载水舱（左）NO.1 T.S.W.B TK (S) 1号顶边压载水舱（右）NO.2 T.S.W.B TK (P) 2号顶边压载水舱（左）NO.2 T.S.W.B TK (S) 2号顶边压载水舱（右）NO.3 T.S.W.B TK (P) 3号顶边压载水舱（左）NO.3 T.S.W.B TK (S) 3号顶边压载水舱（右）NO.3 C.H/W.B TK 3号货仓/压载水舱APT 艉尖舱HFO tanksNO.1 HFO TK(P) 1号燃油舱（左）NO.1 HFO TK(S) 1号燃油舱（右）NO.2 HFO TK(P) 2号燃油舱（左）NO.2 HFO TK(S) 2号燃油舱（右）NO.3 HFO TK(P) 3号燃油舱（左）NO.3 HFO TK(S) 3号燃油舱（右）NO.1 HFO SERV TK 1号燃油日用舱NO.2 HFO SERV TK 2号燃油日用舱NO.1 HFO SETT TK 1号燃油沉清舱NO.2 HFO SETT TK 2号燃油沉清舱MDO tanksNO.1 MDO TK 1号柴油舱NO.2 MDO TK 2号柴油舱NO.3 MDO TK 3号柴油舱NO.1 MDO SERV TK 1号柴油日用舱NO.2 MDO SERV TK 2号柴油日用舱EG MDO D TK 应发柴油日用柜MDO TK FOR INCINERATOR 焚烧炉柴油柜CO tanksNO.1 CYL.OIL /doc/230f76d45022aaea998f0fc2.html 1号汽缸油储存舱NO.2 CYL.OIL /doc/230f76d45022aaea998f0fc2.html 2号汽缸油储存舱NO.1 CLY.OIL MEASURING TK 1号汽缸油测量柜NO.2 CLY.OIL MEASURING TK 2号汽缸油测量柜LO tanksM/E LO /doc/230f76d45022aaea998f0fc2.html 主机滑油储存舱M/E LO SETT. TK 主机滑油沉清舱G/E LO /doc/230f76d45022aaea998f0fc2.html 辅机滑油储存舱G/E LO /doc/230f76d45022aaea998f0fc2.html 辅机滑油沉清舱M/E LO SUMP TK 主机滑油循环舱FW tanksFW TK (P) 淡水舱（左）FW TK(S) 淡水舱（右）DISTILLED/doc/230f76d45022aaea998f0fc2.html 蒸馏水舱Other tanks and sea chests/doc/230f76d45022aaea998f0fc2.html 艉管冷却水舱F.W. WASHING TK 洗舱水舱SLOPE/SEWAGE WASHING TK 洗舱污水/生活污水舱SLUDGE TK 油渣舱BILGE HOLD TK 舱底水存放舱F.O OVERF. TK 燃油溢流舱F.O DRAIN TK 燃油泄放舱WASTE OIL TK 废油舱S/T LO. DRAIN TK 艉管滑油泄放舱SEWAGE TK 生活污水舱CHAIN LOCKER TK ( P) 锚链舱(左）CHAIN LOCKER TK ( S) 锚链舱(右）STERN TUBE LO GRAITY TK 艉管滑油重力油柜STEERING GRAR STORAGE OIL Tk 舵机储油箱M/E SCAVENGE BOX DRAIN TK 主机扫气箱泄放柜CHEMECAL CLEANING TK ME 主机化学清洗柜ALARM DEVICE BOX 报警装置箱M/E JACKET FW.EXPANSION TK 主机缸套水膨胀水箱LT FRESH WATER EXPANSION TK 低温水膨胀水箱Low Sea Chest 低位海底门High Sea Chest 高位海底门Emer. Sea Chest 应急海底门Tanks tightness testBW tanksFPT 艏尖舱NO.1 B.S.W.B TK (P) 1号底边压载水舱（左）NO.1 B.S.W.B TK (S) 1号底边压载水舱（右）NO.2 B.S.W.B TK (P) 2号底边压载水舱（左）NO.2 B.S.W.B TK (S) 2号底边压载水舱（右）NO.3 B.S.W.B TK (P) 3号底边压载水舱（左）NO.3 B.S.W.B TK (S) 3号底边压载水舱（右）NO.4 B.S.W.B TK (P) 4号底边压载水舱（左）NO.4 B.S.W.B TK (S) 4 号底边压载水舱（右）NO.5 B.S.W.B TK (P) 5号底边压载水舱（左）NO.5 B.S.W.B TK (S) 5号底边压载水舱（右）NO.1 T.S.W.B TK (P) 1号顶边压载水舱（左）NO.1 T.S.W.B TK (S) 1号顶边压载水舱（右）NO.2 T.S.W.B TK (P) 2号顶边压载水舱（左）NO.2 T.S.W.B TK (S) 2号顶边压载水舱（右）NO.3 T.S.W.B TK (P) 3号顶边压载水舱（左）NO.3 T.S.W.B TK (S) 3号顶边压载水舱（右）APT 艉尖舱HFO tanksNO.1 HFO TK(P) 1号燃油舱（左）NO.1 HFO TK(S) 1号燃油舱（右）NO.2 HFO TK(P) 2号燃油舱（左）NO.2 HFO TK(S) 2号燃油舱（右）NO.3 HFO TK(P) 3号燃油舱（左）NO.3 HFO TK(S) 3号燃油舱（右）NO.1 HFO SERV TK 1号燃油日用舱NO.2 HFO SERV TK 2号燃油日用舱NO.1 HFO SETT TK 1号燃油沉清舱NO.2 HFO SETT TK 2号燃油沉清舱MDO tanksNO.1 MDO TK 1号柴油舱NO.2 MDO TK 2号柴油舱NO.3 MDO TK 3号柴油舱NO.1 MDO SERV TK 1号柴油日用舱NO.2 MDO SERV TK 2号柴油日用舱EG MDO D TK 应发柴油日用柜MDO TK FOR INCINERATOR 焚烧炉柴油柜CO tanksNO.1 CYL.OIL /doc/230f76d45022aaea998f0fc2.html 1号汽缸油储存舱NO.2 CYL.OIL /doc/230f76d45022aaea998f0fc2.html 2号汽缸油储存舱NO.1 CLY.OIL MEASURING TK 1号汽缸油测量柜NO.2 CLY.OIL MEASURING TK 2号汽缸油测量柜LO tanksM/E LO /doc/230f76d45022aaea998f0fc2.html 主机滑油储存舱M/E LO SETT. TK 主机滑油沉清舱G/E LO /doc/230f76d45022aaea998f0fc2.html 辅机滑油储存舱G/E LO /doc/230f76d45022aaea998f0fc2.html 辅机滑油沉清舱M/E LO SUMP TK 主机滑油循环舱FW tanksFW TK (P) 淡水舱（左）FW TK(S) 淡水舱（右）DISTILLED/doc/230f76d45022aaea998f0fc2.html 蒸馏水舱Other tanks and sea chests/doc/230f76d45022aaea998f0fc2.html 艉管冷却水舱F.W. WASHING TK 洗舱水舱SLOPE/SEWAGE WASHING TK 洗舱污水/生活污水舱SLUDGE TK 油渣舱BILGE HOLD TK 舱底水存放舱F.O OVERF. TK 燃油溢流舱F.O DRAIN TK 燃油泄放舱WASTE OIL TK 废油舱S/T LO. DRAIN TK 艉管滑油泄放舱SEWAGE TK 生活污水舱CHAIN LOCKER TK ( P) 锚链舱(左）CHAIN LOCKER TK ( S) 锚链舱(右）STERN TUBE LO GRAITY TK 艉管滑油重力油柜STEERING GRAR STORAGE OIL Tk 舵机储油箱DE-AERATING TK 高温淡水除气筒M/E SCAVENGE BOX DRAIN TK 主机扫气箱泄放柜CHEMECAL CLEANING TK ME 主机化学清洗柜M/E JACKET FW.EXPANSION TK 主机缸套水膨胀水箱LT FRESH WATER EXPANSION TK 低温水膨胀水箱Low Sea Chest 低位海底门High Sea Chest 高位海底门Emer. Sea Chest 应急海底门Tightness before launchingoverboard discharge valves 排舷外阀ICCP 外加电流阴极保护Speed log and echo sounder 计程仪和测深仪Installlation of systems and electrical equipmentPiping systems installation & tightnessMDO systemMDO transfer pipe system in ER 机舱柴油驳运管系"MDO daily system of ME, AE ,EG, steam boiler 柴油日用管系" MDO separating system 柴油净化管系Overflow pipes of MDO TKS and MDO TK FOR INCINERATOR 柴油沉清舱及焚烧炉柴油柜的溢流管系HFO systemHFO transfer system in ER 机舱燃油驳运管系HFO transfer system Fr 35 Fore 货仓燃油驳运管系"HFO daily system of ME, AE, steam boiler 燃油日用管系"HFO separating system 燃油净化管系Overflow pipes of HFO SETT TKS and NO.3 HFO TK 燃油沉清舱及3#燃油舱的溢流管系LO systemLO deck filling systems of ME and AE 主辅机甲板滑油注入管系LO daily circulating system of ME 主机滑油日用管系LO separating system of ME and AE 主辅机滑油净化管系LO service system of sterntube 艉管滑油日用管系CO systemCO deck filling system 甲板汽缸油注入管系CO system of ME 主机汽缸油管系FO and LO drainage systemFO drainage system 燃柴油泄放系统LO drainage system 滑油泄放系统Hydr oil systemfree fall boat hydr oil system 抛落艇液压管系steer gear hydr oil system (only check installation) 舵机液压管系(只看安装）windlass hydro.system in forecastle 首部锚绞机液压油管.winch hydro.system in aft. 尾部绞机液压油管.hydro. Oil system for H/C hydro. Power pack1 ？hydro. Oil system for H/C hydro. Power pack2 ?hydro. Oil filling pipes for four deck cranes ?hydro. Oil pipes for all H/C cylinders ?Cooling water sytemMain sea water pipe 主海水管系Sea water cooling system 海水冷却管系Sea water piping system of fresh water generator 造水机的海水管系ME HT cooling water system 主机高温冷却水管系ME/AE LT cooling water system 主辅机低温冷却水管系Compressed air systemsStarting air system of ME 主机启动空气Starting air system of AE 辅机启动空气Control air system in ER 机舱控制空气Air system of air horn 汽笛空气管系Working air system in ER including air reducing station pipes 机舱杂用空气及减压阀组管系Working air system on superstructure 上建杂用空气管系Fr 35 Fore working air system 货仓杂用空气管系quick closing valves system 快关阀空气管系deck washing and Fire-fighting piping systemsSuperstructure 上建ER 机舱Fr 35 Fore 货仓主甲板mist water fire figthing system in ER 机舱水雾喷淋CO2 piping systemCO2 release system in ER 机舱CO2 释放管系CO2 release system Fr 35 Fore 货仓CO2 释放管系CO2 control pipes CO2 控制管CO2 release pipes for galley 厨房CO2 释放管系CO2 release pipes for painting store room 油漆间CO2 释放管系Water supply system ( cold/hot water)ER 机舱Superstructure 上建Ballast & bilge piping systemER 机舱区域Fr 35 Fore 货舱区域steam and central heating systemsboiler feed water 锅炉给水系统steam and condensate system in ER 机舱蒸汽冷凝系统steam and condensate system in pipe tunnel 管弄蒸汽冷凝系统steam heat tracing system 蒸汽伴行管Heating coil pipesNO.1 HFO TK(P) 1号燃油舱（左）NO.1 HFO TK(S) 1号燃油舱（右）NO.2 HFO TK(P) 2号燃油舱（左）NO.2 HFO TK(S) 2号燃油舱（右）NO.3 HFO TK(P) 3号燃油舱（左）NO.3 HFO TK(S) 3号燃油舱（右）NO.1 HFO SERV TK 1号燃油日用舱NO.2 HFO SERV TK 2号燃油日用舱NO.1 HFO SETT TK 1号燃油沉清舱NO.2 HFO SETT TK 2号燃油沉清舱SLUDGE TK 油渣舱ME LO /doc/230f76d45022aaea998f0fc2.html 主机滑油沉清舱AE LO /doc/230f76d45022aaea998f0fc2.html 辅机滑油沉清舱ME LO SUMP TK 主机滑油循环舱F.O OVERFLOW TK 燃油溢流舱BILGE HOLD TK 舱底水存放舱WASTE OIL TK 废油舱F.O DRAIN TK 燃油泄放舱CHEMICAL CLEANING TK 化学清洗柜ME SCAVENG DRAIN TK 主机扫气箱泄放柜bilge water separator pipes and sludge dischargebilge water separator pipes 舱底油水分离器管系sludge discharge pipes 油渣排舷外管系O2 and C2H2 pipes to workshopO2 and C2H2 pipes to workshop 氧气乙炔去机修间管系Black water & gray water pipesSuperstructure 上建区域ER 机舱区域Cleaning system of main engine scav. Air coolerchemical cleaning system of MEAC and cold store refrigerating systemsAC refrigerating copper pipes cleaning 空调制冷铜管清洁AC refrigerating installation and pressure test 空调制冷铜管安装及密性AC refrigerating vacuum test 空调制冷铜管抽真空Cold store refrigerating copper pipes cleaning 冷库制冷铜管清洁Cold store refrigerating installation and pressure test 冷库制冷铜管安装及密性Cold store refrigerating vacuum test 冷库制冷铜管抽真空A/C duct and mechanical ventilation systemA / C spiral ducts and mechanical vent pipes insuperstructurecabines 上建各房间空调螺旋通风管和机械通风管安装"mechanical vent ducts in ER, CO2 room,steering gear room, purifier room, workshop etc. 机舱，CO2室等房间机械通风管安装"remote control pipes(two core tube) of remote control valves remote control pipes(two core tube) of remote control valves 遥控阀多芯管Exhaust pipesInstallation of exhaust pipesAE 发电机EG 应发steam boiler 蒸汽锅炉ME 主机Water drain pipes"superstructure, main deck and forecastle 上建，主甲板，艏部"ER 机舱ER oil & water tanks vent pipesER oil & water tanks vent pipes 机舱各油&水舱透气管安装及密性Electrical systems and equipment installationCable trays"Forecastle boatswain's store room, deck store room,carpenter room,paint room etc. 艏部水手长储藏室，甲板储藏室，木工间，油漆间等"main deck hatchcoaming PS and SB 主甲板舱口围左右舷Inside of all cargo hold transverse walkways 货仓内梯道Pipe tunnel 管弄A deck to compass deck A甲板到罗经甲板Engine room 机舱Cables layout"Forecastle boatswain's store room, deck store room,carpenter room,paint room etc. 艏部水手长储藏室，甲板储藏室，木工间，油漆间等"main deck hatchcoaming PS and SB 主甲板舱口围左右舷Inside of all cargo hold transverse walkways 货仓内梯道Pipe tunnel 管弄A deck to compass deck A甲板到罗经甲板Engine room 机舱Cables penetration"Forecastle boatswain's store room, deck store room,carpenter room,paint room etc. 艏部水手长储藏室，甲板储藏室，木工间，油漆间等"main deck hatchcoaming PS and SB 主甲板舱口围左右舷Inside of all cargo hold transverse walkways 货仓内梯道Pipe tunnel 管弄A deck to compass deck A甲板到罗经甲板Engine room 机舱Cables glandsForecastle deck 艏楼甲板main deck hatch coaming PS and SB 主甲板舱口围左右舷Outside superstructure 上建室外Engine room 机舱Pipe tunnel 管弄Inside cargo hold 货仓内部Main electrical equipment installation and cleanessMain switchboard 主配电板Emergency switchboard 应急配电板Engine control console 集控台Wheel house console 驾控台Flushing/Blowing of systems and cleaness of tanksSystems flushing/blowing/cleaningMDO/HFO"HFO&MDO daily system of ME, AE , steam boiler 燃柴油日用系统 "HFO&MDO separating system 燃柴油净化管系LOLO deck filling systems of ME and AE 主辅机甲板滑油注入管系LO daily circulating system of ME 主机滑油日用管系LO separating system of ME and AE 主辅机滑油净化管系LO service system of sterntube 艉管滑油日用管系Hydr oilfree fall boat hydr oil system 抛落艇液压管系steer gear hydr oil system 舵机液压管系windlass hydro.system in forecastle 首部锚绞机液压油管.winch hydro.system in aft. 尾部绞机液压油管.hydro. Oil system for H/C hydro. Power pack1 ？hydro. Oil system for H/C hydro. Power pack2 ？hydro. Oil filling pipes for four deck cranes ？hydro. Oil pipes for all H/C cylinders ？CO systemCO deck filling system 甲板汽缸油注入管系CO system of ME 主机汽缸油管系Cooling waterHT cooling water system 高温冷却水管系LT cooling water system 低温冷却水管系HT cooling water sample analyze after chemical added 高温冷却水加药后取样LT cooling water sample analyze after chemical added 低温冷却水加药后取样Air systemsStarting air system of ME 主机启动空气Starting air system of AE 发电机启动空气CO2CO2 release system in ER 机舱CO2释放管系CO2 release system Fr.35 Fore 货仓CO2释放管系"Steam, feed water and central heating"boiler feed water system including hotwell 锅炉给水管系及热井boiler feed water sample analyze after chemical added 锅炉给水加药后取样steam and condensate system 蒸汽冷凝管系O2 and C2H2 pipes to workshopO2 and C2H2 pipes to workshop 氧乙炔管系Tanks cleanness and blind free inspection before closing manholesHFO tanks cleanness and blind free inspectionNO.1 HFO TK(P) 1号燃油舱（左）NO.1 HFO TK(S) 1号燃油舱（右）NO.2 HFO TK(P) 2号燃油舱（左）NO.2 HFO TK(S) 2号燃油舱（右）NO.3 HFO TK(P) 3号燃油舱（左）NO.3 HFO TK(S) 3号燃油舱（右）NO.1 HFO SERV TK 1号燃油日用舱NO.2 HFO SERV TK 2号燃油日用舱NO.1 HFO SETT TK 1号燃油沉清舱NO.2 HFO SETT TK 2号燃油沉清舱MDO tanks cleanness and blind free inspectionNO.1 MDO TK 1号柴油舱NO.2 MDO TK 2号柴油舱NO.3 MDO TK 3号柴油舱NO.1 MDO SERV TK 1号柴油日用舱NO.2 MDO SERV TK 2号柴油日用舱EG MDO D TK 应发柴油日用柜MDO TK FOR INCINERATOR 焚烧炉柴油柜LO tanks cleanness blind free inspectionM/E LO /doc/230f76d45022aaea998f0fc2.html 主机滑油储存舱M/E LO SETT. TK 主机滑油沉清舱G/E LO /doc/230f76d45022aaea998f0fc2.html 辅机滑油储存舱G/E LO /doc/230f76d45022aaea998f0fc2.html 辅机滑油沉清舱M/E LO SUMP TK 主机滑油循环舱CO tanks cleanness blind free inspectionNO.1 CYL.OIL /doc/230f76d45022aaea998f0fc2.html 1号汽缸油储存舱NO.2 CYL.OIL /doc/230f76d45022aaea998f0fc2.html 2号汽缸油储存舱NO.1 CLY.OIL MEASURING TK 1号汽缸油测量柜NO.2 CLY.OIL MEASURING TK 2号汽缸油测量柜FW tanks cleanness blind free inspectionFW TK (P) 淡水舱（左）FW TK(S) 淡水舱（右）DISTILLED/doc/230f76d45022aaea998f0fc2.html 蒸馏水舱Other tanks cleanness blind free inspection/doc/230f76d45022aaea998f0fc2.html 艉管冷却水舱F.W. WASHING TK 洗舱水舱SLOPE/SEWAGE WASHING TK 洗舱污水/生活污水舱SLUDGE TK 油渣舱BILGE HOLD TK 舱底水存放舱F.O OVERF. TK 燃油溢流舱F.O DRAIN TK 燃油泄放舱WASTE OIL TK 废油舱S/T LO. DRAIN TK 艉管滑油泄放舱SEWAGE TK 生活污水舱CHAIN LOCKER TK ( P) 锚链舱(左）CHAIN LOCKER TK ( S) 锚链舱(右）STERN TUBE LO GRAITY TK 艉管滑油重力油柜STEERING GRAR STORAGE OIL Tk 舵机储油箱M/E SCAVENGE BOX DRAIN TK 主机扫气箱泄放柜CHEMECAL CLEANING TK ME 主机化学清洗柜M/E JACKET FW.EXPANSION TK 主机缸套水膨胀水箱LT FRESH WATER EXPANSION TK 低温水膨胀水箱Main Propulsion and Rudder installationPropeller shaft and rudder center line alignmentER area construction Fr.35 after and under main deck are finishedME foundation are prealignedME foundation are weldedPropeller shaft and rudder center line alignment by steel wire ME foundation all through bolt holes drilled"Stern tube, propeller shaft , blades installation "Cleaning stern tube before fixing stern tube outsideRudder system installationbearing sleeves 2 pcs rudder stock workshop"ME shifting, superstructure shifting and reaming shaft coupling/ ME fly wheel fitting bolts holes "flat bars to be welded inside ME foundation for chockfast"ME alignment, installations , shaft jack up test , shaft earth device etc."dynamic measurement before shaft alignmentAE/EG installationAE 1 chock fitting and foundation bolts tighten 1#发电机垫块安装及螺栓扳紧AE 2 chock fitting and foundation bolts tighten 2#发电机垫块安装及螺栓扳紧AE 3 chock fitting and foundation bolts tighten 3#发电机垫块安装及螺栓扳紧EG chock fitting and foundation bolts tighten 应急发电机垫块安装及螺栓扳紧Deck equipment installationWindlass foundation pouring chockfast and bolts tighten 锚机底座浇环氧及螺栓扳紧Winches foundation pouring chockfast and bolts tighten 绞车底座浇环氧及螺栓扳紧"Trial, Alarms and Other Tests"EG function testalarm points of EG 应发报警点load test 应发负荷AE function test"alarm points of AE1, AE2, AE3 1#，2#，3# 发电机报警点"load test of Aes 1#，2#，3# 发电机负荷parallel run test of main generators 主发并车"MSB, ESB and shore connection box"protection devices and equipment of MSB 主配电板保护protection devices and equipment of ESB 应急配电板保护protection of shore connection box 岸电保护24 V auto battery charge/discharge panelalarm points 报警点charge and discharge test 充电和放电试验Steam boilerSteam boiler boiling out(cleaning chamber) 蒸汽锅炉煮炉（清洁炉室）Steam boiler alarm points 蒸汽锅炉报警点boiler feed water pumps 锅炉给水泵dosing pump for steam boiler 锅炉加药泵Steam boiler functon test on MDO 锅炉烧柴油试验Steam boiler functon test on HFO 锅炉烧重油试验Engine room equipments/pumps teststeering gear 舵机"HFO, LO separators 燃油滑油分油机"incinerator 焚烧炉engine room fans 机舱风机"main air compressors ， service air compressor, emergency air compressor;main air reservoir,contrlo air reservoir，service air reservoir,emerg.air reservoir 主空压机,甲板日用空压机，应急空压机；主空气瓶，控制空气瓶,甲板日用空气瓶，应急空气瓶"control air dehydrator 控制空气干燥器air reducing station 减压阀组SW cooling pumps 海水冷却水泵LT CW main and harbour pumps 低温冷却水泵及停港冷却水泵M/E jacket F.W cooling pumps 主机缸套水冷却水泵"FW hydrophor, FW pumps , UV lamp 淡水压力柜，淡水压力泵紫外线消毒器""TW hydrophor , TW pump 技术水压力柜技术水泵 ""calorifier, hot water circulating pumps 热水柜，热水循环泵"LO transfer pump 滑油输送泵stern tube LO pump 艉管滑油泵CYC. Oil transfer pump 汽缸油输送泵sludge pump including dry running protection 油渣泵包括防干磨保护oily water separator 油水分离器sewage treatment plant including sewage discharge pump 污水处理装置包括污水排放泵ER crane function and load test 机舱行车效用及负荷试验cold store refrigerating plant function test including cooling effective test 冷库制冷单元效用及冷库制冷试验"emergency stop test for FO, LO pumps and fans 风油切断"FW generator test and F.W mineralizing unit (sea trial) 造水机及矿化滤器ME air cooler chemical cleaning pump 主机空冷器化学清洗泵electrical test panel 电工实验板Workshops equipment testsgas welding 气焊elec. Welding 电焊grinding machine 砂轮机drilling machine 钻床lathe machine 车床grinding machine for exh.valve 排气阀研磨机M/E fuel valve test device 主机喷油器试验装置Systems of whole vessel function testspiping system with pump function testsbilge water system for whole vessel including pumps and ejectors 全船舱底水效用包括泵浦及喷射泵ballast system including pumps and stripping ejectors 压载水效用包括泵浦及扫舱喷射泵fire fighting system for whole vessel including pumps 全船消防效用及泵浦water mist fire extinguishing system in ER including pump unit 机舱水雾喷淋效用及泵浦单元steam heating system for ER tanks 机舱舱室蒸汽加热系统steam heating system for HFO storage tanks 货仓燃油储存舱蒸汽加热系统steam heat tracing system 蒸汽伴行系统效用HFO and MDO transfering system test including pumps 燃、柴油驳运效用及泵浦FW hot / cold and TW supply system in superstructure 上建供水FW hot / cold and TW supply system in ER 机舱供水"drain pipes in superstructure ,main deck,forecastle deck 上建，主甲板，首部疏排水系统""drain pipes of FO drain ,LO drain and water drain in ER 机舱燃油，滑油水泄放""air supply system for ER, main deck and forecastle 全船杂用空气效用"remote control valves system 遥控阀系统remote level measuring system + manual sounding 液位遥测系统+ 手动测深quick closing valve systems function test 快关阀系统效用"CO2 system for whole vessel(ER, CH，galley，painting store) 全船CO2效用"cargo hold smoke detection 货仓烟雾探测bridge windows washing system including wipers 驾驶室雨刮器效用sea chests P/S function test of the valves 左右海底门遥控阀效用Ventilation systems in whole vessel incl fans"ER and ER other spaces ventilation including fans, flaps etc机舱及机舱内其他区域通风包括风机，风闸""superstructure ventilation including fans, flaps etc 上建通风包括风机风闸""cargo hold ventilation including fans, flaps etc 货仓通风包括风机，风闸"AC system in accomodationAC plant test 中央空调AC system in accomodation effective test 上建风量测试air condition system for galley 厨房空调air condition system for ECR 集控室空调Level alarms and temperature alarmsHFO and MDO tanksHFO tks (Tk01-03)high level 燃油舱1-3#舱液位高MDO tanks high level (TK01-03) 柴油舱1-3#液位高FO overflow tank level high(ER) 燃油溢流舱液位高NO.1 HFO SETT TK level high 1#燃油沉清舱液位高NO.2 HFO SETT TK level high 2#燃油沉清舱液位高NO.1 HFO SERV TK level low 1#燃油日用舱液位低NO.2 HFO SERV TK level low 2#燃油日用舱液位低NO.1 MDO SERV TK level low 1#柴油日用舱液位低NO.2 MDO SERV TK level low 2#柴油日用舱液位低HFO tanks (TK01-03) temperature high 燃油舱1-3# 温度高NO.1 HFO SETT TK temperature high 1#燃油沉清舱温度高NO.2 HFO SETT TK temperature high 2#燃油沉清舱温度高NO.1 HFO SERV TK temperature high 1#燃油日用舱温度高NO.2 HFO SERV TK temperature high 2#燃油日用舱温度高MDO SERV tank for emergency generator level low 应发柴油柜液位低INCIN. M.D.O. TK. Low level 焚烧炉柴油柜液位低LO and CO tanksLO sump Tank ME level low 主机滑油循环舱液位低LO stern tube head tank level low 艉管滑油重力柜液位低LO stern tube forward seal tank level low 艉管艏密封柜液位低LO stern tube forward seal tank level high 艉管艏密封柜液位高LO stern tube after seal tank level low 艉管艉密封柜液位低LO stern tube after seal tank level high 艉管艉密封柜液位高LO stern tube DRAIN TK.level low 艉管滑油泄放舱液位低No.1 M/E CYL. OIL MEASUR. TK. Level low 1#主机汽缸油测量柜液位低No.2 M/E CYL. OIL MEASUR. TK. Level low 2#主机汽缸油测量柜液位低Bilge wellsBilge well in cargo hold 5 SB level high No.5货舱污水井液位高(右)Bilge well in cargo hold 5 PS level high No.5货舱污水井液位高(左)Bilge well in cargo hold 4 AFT. SB level high No.4货舱污水井液位(后右)Bilge well in cargo hold 4 AFT. PS level high No.4货舱污水井液位(后左)Bilge well in cargo hold 4 FWD. SB level high No.4货舱污水井液位(前右)Bilge well in cargo hold 4 FWD. PS level high No.4货舱污水井液位(前左)Bilge well in cargo hold 3 SB level high No.3货舱污水井液位高(右)Bilge well in cargo hold 3 PS level high No.3货舱污水井液位高(左) Bilge well in cargo hold 2 AFT.SB level high No.2货舱污水井液位高(后右) Bilge well in cargo hold 2 AFT.PS level high No.2货舱污水井液位高(后左) Bilge well in cargo hold 2 FWD.SB level highNo.2货舱污水井液位高(前右) Bilge well in cargo hold 2 FWD.PS level high No.2货舱污水井液位高(前左) Bilge well in cargo hold 1 SB level high No.1货舱污水井液位高(右)Bilge well in cargo hold 1 PS level high No.1货舱污水井液位高(左)Bilge well in boatswain store SB level high 水手长储藏室污水井液位高（右）Bilge well in boatswain store PS level high 水手长储藏室污水井液位高（左）Bilge well in windlass control room level high 锚机控制室液位高Bilge well in carpenter room level high 木工间液位高Bilge well in painting room level high 油漆间液位高Bilge well in FORE. VOID SB level high 首空仓液位高（右）Bilge well in FORE. VOID PS level high 首空仓液位高（左）Bilge well in LOG&SOUND room level high 计程仪测深仪室液位高Bilge water in pipe tunnel level high 管弄舱底水液位高Bilge water level in emergency fire pump room level high 应急消防泵舱舱底水液位高Bilge well in engine room FWD. PS level high 机舱前污水井左舷液位高Bilge well in engine room FWD. SB level high 机舱前污水井右舷液位高Bilge well in engine room AFT. Level high 机舱尾部污水井液位高Bilge well beneath M/E level high 主机座下污水井液位高ER tanksM/E J.F W. EXP. TK. Level low 主机缸套水膨胀水箱液位低LT FCW expansion tank level low 低温冷却水膨胀水箱液位低M/E H.T.F.W. AL.device box level low 主机缸套水报警装置液位低waste oil tank level high 废油舱液位高sludge oil tank level high 油渣舱液位高FO. Drain TK level high 燃油泄放舱液位高FRESH W. TK. Level low (P) 淡水舱左舷液位低INCIN. WASTE TK. Level high 焚烧炉废油柜液位高BILGE HOLD. TK.level high 舱底水存放舱液位高SEWAGE TK. (BLACK W.) level high 生活污水舱液位高ballast water tanksmanual sounding pipes function test for all ballast water tanks 所有压载舱手动测试效用Main propulsion system mooring testME alarm points 主机报警点ME pre-heating unit 主机预热单元ME turning gear 主机盘车机ME FO booster unit 供油单元ME LO auto. Filter 主机滑油自清滤器ME LO sump 主机滑油泵shaft earthing device 轴接地装置ME mooring test 主机系泊试验ME turbocharger cleaning system (sea trials) 主机涡轮增压器清洗Accomodation equipment testgalley equipment 厨房设备laundry equipment 洗衣间设备Deck equipment and outfittings testsbunker hose crane 油管吊Anchor abandoning test 弃锚试验deck cranes function and load test 甲板克令吊效用及负荷试验provision crane function and load test 杂物吊效用及负荷试验accommodation ladders function and load test 舷梯效用及负荷试验Pilot ladder 引水员软梯rescue boat davit 救助艇架rescue boat 救助艇free fall boat 抛落艇free fall boat davit 抛落艇架mooring winches 系泊绞车anchor windlasses 锚机H/C hydro. Power pack1 舱盖液压单元"doors, windows and small hatchcovers"operating test 开关试验host test 冲水试验dead weight measurement 空船称重Electrical systemselectrical space heaters for whole vesselelectrical space heater in sanitary units 卫生单元电加热器electrical space heater in store rooms 甲板储藏室电加热器Lightingsnormal and emergency lightingsuperstructure open deck 上建室外superstructure accomodation 上建室内ER and service spaces 机舱及机舱其他服务场所"main deck and forecastle including deck cranes, power pack rooms, store room, etc 主甲板，艏部包括克令吊，液压单元室，甲板储藏室等等"cargo holds 货仓pipe tunnel 管弄nautical lightingnavigation and signal lights 航行灯和信号灯suez searching light 苏伊士搜救灯Suez Canal light socket 苏伊士运河灯插座daytime signal searching light 白昼信号搜索灯panama Canal steering light 巴拿马运河操舵灯anti-fouling and cathodic protection systems 防海生物及外加电流阴极保护"Communication, indication, signalling equipment & alarm systems"fire/smoke detection system alarm 火警及烟雾探测bunker station alarm / telephone 加油站报警、电话water ingress alarm sysytem 货仓进水报警系统cold store room call 冷库误锁hospital call 病房呼叫general alarm system 通用报警E/R telegraph 机舱车种automatic telephone 自动电话sound power telephone 声力电话E/R column alarms 机舱灯柱报警talk back system 对讲public address system 广播Community antenna device 天线共用器master clock test 子母钟open/close indicators for WT doors and small covers. 水密门及小舱盖开闭指示fog horn 雾笛nautical radio & communication equipmentEcho-sounder 回声测深仪speed log 计程仪Gyro-compass 电罗经automatic pilot 自动操舵仪Radar &responder 雷达及雷达应答器D-GPS D-GPS 导航仪VHF radiophone VHF 无线电话VDR 航行数据记录仪SATCOM C / SATCOM F 卫星通讯系统C站，F站DSC 数字选呼电话设备EPIRB 应急无线电示位标SSAS 防海盗系统Network systems and computersLoading computer 装载计算机Ships network system 船舶网络系统AIS-system 船舶状态识别系统Seatrials。
船舶英语汇总审批稿
(Delivery expressions for main engine)68
二十四、空压机和空气系统用语
(Air compressor and Air system)···· 75
二十五、锅炉提交用语
(Delivery expressions for boiler)···77
1．主机Main engine
2．二冲程柴油机Two-stroke diesel engine
3．四冲程柴油机Fore-stroke diesel engine
4．高速柴油机High speed diesel engine
5．中速柴油机Middle speed diesel engine
6．低速柴油机Low speed diesel engine
二十九、救生艇提交过程用语
(Delivery expressions for lifeboat)··92
三十、其他提交项目
(Delivery expressions for other items)···95
三十一、甲板机械系泊试验
(Mooring test for deck machinery)········96
三十二、机舱设备系泊试验
(Mooring test for the equipment in E/R)···98
三十三、谈论故障常用语
（Expressions for trouble）············100
三十四、谈论检修常用语
(Expressions for overhaul)············101
十、常用油类(Oil in common use)·····28
十一、常用量词
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
六、甲板机械类（Deck machinery）······ 18
七、工具类(Word about tools) ········ 20
八、常用物料(Material in common use)26
九、常用紧固件
(Part of fixation in common use)··· 28
1．主机Main engine
2．二冲程柴油机Two-stroke diesel engine
3．四冲程柴油机Fore-stroke diesel engine
4．高速柴油机High speed diesel engine
5．中速柴油机Middle speed diesel engine
6．低速柴油机Low speed diesel engine
十九、时间、季节与方向
(Time、Season and Direction) ·····42
二十常用词组（Phrases in common use）·45
二十一、常用动词和例句
(Verb in common use and example)····48
二十二、问候和常用表达语
(Greeting and common expression)····67
12．三管轮Fourth engineer
13．机匠长Chief motorman
15．机匠Fitter
16．加油工Oil man
17．大电Chief electrician
18．电工Electrician
19．车间主任Workshop director
20．工长Section chief
21．班长Fore man
7．气缸盖(缸头)Cylinder head
22．钳工Fitter
23．主管工程师Engineer in charge
24．机务&船东Superintendent &Super &Owner
25．助理工程师Assistant engineer
26．验船师（机）Register
27．验船师（船）Surveyor
28．油漆工Painter
29．焊工Welder
二十六、锚绞车提交过程用语(Delivery expressions for anchor windlass)79
二十七、舵机提交过程用语
(Steering gear delivering)··· 87
二十八、付机提交过程用语
（Delivery expression for A/E）····· 91
十、常用油类(Oil in common use)·····28
十一、常用量词
(Quantifier in common use)·········29
十二、国家名称(Name of country)。 30
十三、常用缩语
(abbreviation in common use)·····31
十四、船用动态常用单词(marine tends word)32
二十九、救生艇提交过程用语
(Delivery expressions for lifeboat)··92
三十、其他提交项目
(Delivery expressions for other items)···95
三十一、甲板机械系泊试验
(Mooring test for deck machinery)········96
三十二、机舱设备系泊试验
(Mooring test for the equipment in E/R)···98
三十三、谈论故障常用语
（Expressions for trouble）············100
三十四、谈论检修常用语
(Expressions for overhaul)············101
三十五、谈论试验和检验
(Talking about test & check)···········103
三十六、谈论技术要求
(Talking about technology required)···105
一．职位及工种(Titles and type of work)
1．船长Captain
2．大副Chief officer
船舶英语汇总
船舶英语
一.职位及工种
(Titles and type of work)····· 1
二、柴油机类
(Words about diesel engine) ····· 3
三、船舶机械类
(Words about marine machinery) ·· 11
四、阀门(Words about valve) ···· 14
30．大橱Chief cook
31．物料员Store keeper
32．加油工Oiler
33．机工Mechanic
34．甲板员Deck man
35．电线工Wireman
36．外包工Laborer
37．铸工Molder
38．管子工Pipe fitter
39．起重工Crane operator
二、柴油机类(Words aboutdieselengine)
十五、船舶机电设备操作词汇
(manipulate of marine equipment)·33
十六、故障常用单词
(words about malfunction)····· 35
十七、保养检修常用词汇
(Words about maintain and examination)38
十八、常用数字(Numeral in common use)40
3．二副Second offiபைடு நூலகம்er
4．三副Third officer
5．四副Fourth officer
6．水手长Boatswain
7．水手Sailor & Seaman
8．木匠Carpenter
9．轮机长Chief engineer
10．大管轮Second engineer
11．二管轮Third engineer
二十三、主机提交过程用语
(Delivery expressions for main engine)68
二十四、空压机和空气系统用语
(Air compressor and Air system)···· 75
二十五、锅炉提交用语
(Delivery expressions for boiler)···77