石油钻井英语
教材：石油钻井常用英语手册
A Handbook of English for Oil Drilling石油钻井常用英语手册职工培训教材系列辽河石油勘探局钻井二公司六分公司二OO七年四月A Handbook of English for Oil Drilling石油钻井常用英语手册一、DRILLING 钻井1.Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业.2.Prepared bell nipple. 准备”喇叭口”短节.3.Make up 2 joints of drill pipe. 接两根钻杆.4.Break out this connection. 卸开该接头.5.Make up bottom hole assembly. 组合下部钻具6.Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.7.Number stands on trip out and trip in. 起下钻时给立柱编号.8.Pick up BHA and run to seafloor. 将下部钻具下到海底.9.Pick up stands. 接立柱10.Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱11.Drop TOTCO. 投(陶特)测斜仪12.Fish TOTCO with overshot. 用打捞筒捞起测斜仪13.Resume drilling to T.D. 继续钻进到总深14.Circulate 15 minutes.循环15分钟15.Run in hole. 下钻16.Put out of hole. 起钻17.Make an inventory of all ring gaskets. 开一个所有垫圈的清单e spinning tong. 使用气动扳手19.Operate the air winch. 操作气动绞车y down 57 joints of 5” drill pipe. 甩57根钻杆21.Pick up drill stem test tool. 提起钻杆测试工具22.Circulate mud for 2 hours. 循环泥浆2小时23.Move string during circulation. 在循环时注意活动钻具24.Circulate hole clean. 循环清洗井眼25.Circulate bottoms up. 循环泥浆几周26.Fill up every 5 stands. 每5柱灌泥浆一次27.Check mud weight every 15 minutes. 每15分钟检查泥浆比重28.Reverse out excess cement. 反循环替出多余的泥浆29.Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆30.Stop drilling. 停止钻进31.Drilling ahead. 钻进32.Pull out of hole bit. 起出钻头33.Change bit. 换钻头34.Run the wear bushing. 下抗磨补心35.The bit thread type is regular pin. 钻头丝扣是正规公扣36.What’s the make-up torque? 上扣扭矩要多大?37.Run in 9” collars. 下9”钻铤38.The cathead ca n’t give enough torque. 猫头力量不够39.Connect crossover sub. 接上配合接头40.The tong angle is too small. 大钳的角度太小了41.Stop circulating. 停止循环泥浆42.Break out the stand. 卸立柱43.Set the single into the mousehole. 把这个单根放进鼠洞44.Can we break out the pipe with rotary table? 可用转盘卸扣吗?45.No! Break it out with tong. 不行! 要用大钳卸扣46.Spin it out with the air spanner. 用气动扳手卸扣47.Put the pipe wiper on the string. 装上钻杆刮泥器48.Don’t set this stand back. 这根钻杆不要放在钻杆盒上49.Make up the lift sub. 接好提升短节50.Secure the safety clamp. 上紧安全卡瓦51.The bit is nearing the shoe. 钻头快到套管鞋了52.Slow down the running speed. 放慢下放速度53.This is the undergauged interval. 这是缩径井段54.This is the drilling program. 这是钻井设计书55.How much weight on bit is required? 要加多少钻压?56.Keep the rotary speed at 120---140 RPM. 转速保持120---140转/分57.Keep the flow rate at 3000 LPM. 保持排量3000升/分58.The pump pressure is too high. 泵压太高了59.Don’t ream the hole too fast. 划眼不要太快60.Notice the rotary torque. 注意转盘扭矩的变化61.The penetration rate is getting slower. 钻速变慢了62.The bit is nearly worn out. 钻头快磨光了63.Stop drilling at 2000 meters. 钻至2000米停钻64.Circulate for one hour. 循环一个小时65.The pump pressure has increased. 泵压升高了66.One nozzle may be plugged. 可能有一个水眼(或: 喷嘴)堵了67.What is the hook load? 悬重多少?68.What’s the pick-up weight? 上提重量是多少?69.What’s the lowering weight? 下放重量是多少?70.Run in HWDP. 下加重钻杆71.A stabilizer is needed here. 这里需要一个扶正器72.This is a flexible sub. 这是挠性接头73.This is the BHA log. 这是下部钻具组合记录74.Record all outside and inside diameters. 记录好所有(入井工具的)内外径75.We need a short drill collar. 需要一根短钻铤76.Pull the cat line. 拉猫头77.Operate the break lever. 操作(或:扶)刹把78.Stop the pumps. 停泵79.Make a wiper trip. 通井80.Retrieve wear bushing. 取出抗磨补心81.Bleed off pressure. (释)放压(力)82.Keep 5 wraps on the drum. 滚筒上留5圈83.Set slips. 座上卡瓦84.If tight hole, repeat wiper trip. 如果井眼紧, 重复划眼85.Setback bottom hole assembly. 将下部钻具立于钻杆盒内86.Make sure all alarms are on. 确保所有的警报信号都开着y down TDS spinner. 拆下顶部驱动的旋扣器88.Run in hole bit #15 to bottom. 用15号钻头下钻到井底89.Run in hole to casing shoe. 下钻至套管鞋90.Pick up same bit and BHA. 装上同样的钻头和钻具组合y down 5” HW drill pipe. 甩5”加重钻杆92.Move string every 2 hours. 每2小时活动钻具一次93.Keep area around shaker clean. 保持振动筛区域干净94.Control trip gas. 控制起下钻气95.Ream if needed. 如必要时进行划眼96.Select the best penetration rate. 选择最佳钻进速度97.Fix the traveling assembly. 固定游动系统98.Check power tongs and spinning rope are on drill floor. 检查动力钳和尾绳是否在钻台99.What’s the we ight on bit? 钻压是多少?100.What is the BHA of this well? 这口井的下部钻具如何组合?101.Drill out cement. 钻穿水泥102.Drill out 20” casing shoe. 钻穿20”套管鞋tch the elevator. 扣吊卡104.Unlatch the elevator. 开吊卡105.Set the slips. 放卡瓦106.Adjust the crown-o-matic (crown saver). 调整防碰天车107.Lock the hook pin. 锁紧大钩销子108.Check OD of stabilizer. 检查扶正器的外径109.Perform leak off test. 进行地层破裂(或:渗漏)测试110.Connect kill and choke line. 接上压井和放喷管线111.Reverse out the drill pipe. 反循环清洗钻杆112.Make a short trip. 进行短途起下钻113.Change the cutters. 换割刀114.Slug the pipe. 灌重泥浆115.Drill the stand down. 钻完立柱116.Start/run the shale shaker. 开振动筛117.Start the desanders. 开除砂器118.Start the desilters. 开除泥器119.Change it with a 40 mesh screen. 换成40目筛布120.Shut it off. 关掉121.Pull it to the cat ramp. 把它拉到坡道上去122.Make a fast connection. 接单根要快123.Don’t dump the mud into the s ea. 不要把泥浆排放到海里124.Disconnect it with a chain tong. 用链钳卸开125.Put a thread protector. 加一个(丝扣)护箍126.Can we use the power slips? 可以使用动力卡瓦吗?二、CASING AND CEMENTING 下套管与固井127.R un in hole to bottom for wiper trip. 下钻通井128.T his is the casing program. 这是套管程序129.P repare for running casing. 准备下套管130.M ake everything ready for running 7”casing. 做好下7”套管的准备131.M ake cementing job. 固井132.D isplace cementing with mud pump. 用泥浆泵替泥浆133.S et cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞134.P ick up cementing head. 接水泥头135.C ement samples are hard. 水泥样已凝固136.P ump in 3 cubic meters of spacer. 注3方隔离液137.P ump down the plug. 泵压(胶)塞138.W ait on cement. 候凝139.T he guide shoe will be connected. 接引鞋140.C onnect the floor collar. 接浮箍141.C onnect the air line to the casing stabbing board. 接好套管扶正台的气管线142.R un casing with the 350T slip elevator. 用350吨卡瓦式吊卡下套管143.C lean and dry 20” casing threads with rags. 清洁并擦干20”套管丝扣144.W here is the rabbit for drifting the casing? 套管通径规在哪里?三、FISHING 打捞145.The bit cutters have been lost in the hole. 牙轮落井146.Run in the reverse-circulation basket. 下反循环打捞篮147.There is a lot of junk in the hole. 井下有很多落物148.The fish is 235.46 meters long. 落鱼长度235.46米149.The fish top is at 2478.34 meters. 鱼顶位置2478.34米四、FREEING STUCK PIPE 卡钻与解卡190.The down-hole problems are very complicated. 井下情况很复杂191.The hole is tight. 遇阻了192.Overpull while tripping out. 起钻遇卡(overpull: 超拉力)193.The formation is unstable. 地层不稳定194.The wall caving is severe. 井壁垮塌严重195.There are many return cuttings. 返出岩屑特别多196.The mud returns have decreased. 返出泥浆减少197.The hole is enlarged. 井眼扩大了198.The pipe’s stuck. 卡钻了199.Pull up to 150 tons. 上提150吨200.Slack off to 50 tons. 下放至50吨201.Ream down all the tight points. 在所有遇阻点进行划眼202.The rotary table can’t rotate. 转盘转不动203.Where is the sticking point? 卡点在哪里204.Make a tensile test. 做拉伸试验205.Back it off above the free point. 在卡点以上倒扣206.Where is the back-off position? 脱扣位置在哪207.Plug the well for side tracking. 打水泥塞侧钻五、ABNORMAL WELL CONDITION AND WELL CONTROL异常井况与压井168.The mud is gas out. 泥浆有气侵169.The pit has lowered quickly. 泥浆池液面下降很快170.The hole lost returns. 井口不返泥浆171.The returns are unstable. 返出泥浆量忽大忽小172.Where’s the thief zone? 漏失层在哪里173.Cut down the flow rate. 降低排量174.Lower the mud density. 降低比重175.Cut down the hydrostatic pressure. 减少静压176.The gas smell is strong. 天然气味度很浓177.There’s some trace of oil. 发现有油花178.The pump pressure is fluctuating. 泵压不稳179.It is a zone of abnormal pressure. 这是异常压力层180.The hole (well) is kicking! 井涌啦!181.Shut in the BOP! 关闭防喷器182.Sound the general alarm quickly! 快发出综合警报183.The stand pipe pressure is 10 kg/cm2. 立管压力10公斤/厘米2184.The casing pressure is 25 kg/cm2. 套压2510公斤/厘米2185.Fill out the kill sheet. 填写压井记录表186.Kill the well. 压井187.Ther e’s a combination of lost returns and the kick. 又喷又漏, 情况复杂188.Reverse the gas out of the hole. 反循环排气189.What’s the lag time? 迟到时间是多少190.The well is now stable. 现在井眼已经稳定六、PREPERATION BEFORE MAKING HOLE钻前准备191.Tell the mechanic to check the motor torque . 让机械师检查马达扭矩。
石油钻井工程英语词汇
石油钻井工程英语词汇第一章：石油钻井工程英语基础词汇第1 节石油钻井工程基础词汇钻井：drill定向斜井：directional drilling欠平衡钻井：under-balance drilling海上钻井：off-shore drilling陆地钻井：on-shore drilling钻头：drill bit刮刀钻头：drag bit牙轮钻头：rock bit (镶齿钻头insert bit, 钢齿钻头steel toothed bit) 金刚石钻头：diamond bit取心钻头：coring bit钻头浮阀：float valve钻头水眼：bit nozzle(or jet)钻头水眼刺:bit nozzle washed out钻头规：bit caliper(bit gauge)钻头泥包：bit is balling钻头钝了，我建议现在起钻：bit is dull. I suggest to POOH now钻铤：DC(drill collar )光钻铤slick drill collar，螺旋钻铤spiral drill collar钻杆：DP(drill pipe )方钻杆：kelly公扣：pin end母扣：box end内平式连接：IF(internal flash)正规式连接：REG(regular)贯眼式连接：FH(full hole)加重钻杆heavy weight drill pipe短钻杆pop joint井下马达：down hole motor涡轮钻具：turbine震击器：drilling jar减震器：absorber下部钻具组合：BHA（bottom hole assembly）钻具扶正器：stabilizer（string stabilizer, near-bit stabilizer）钻机：drill rig钻井泥浆：drilling mud钻井液：drilling fluid钻井设备：drilling equipment油：oil原油：crude oil天然气：nature gas煤层气：coal-bed gas石油：petroleum中国石油（简称）：CNPC（China National Petroleum Corporation ）长城钻井（简称）：GWDC(Great Wall Drilling Company)采油：oil production产油层(目的层)：reservoir( or pay zone)钻进：drilling调整钻井参数以得到理想的机械钻速：play the drilling parameters to get fast ROP起钻：POOH(pull out of hole)下钻：RIH(run in hole)下套管：run casing(or RIH with casing)短起下钻：wiper trip循环泥浆：circulate泥浆：reverse circulate中途循环泥浆：break circulation分段下钻：RIH in stages通井：control trip划眼：reaming倒划眼：back reaming接单根：make connection滑、割大绳：slip and cut drilling line by ton-mile保养设备：maintain the equipment修理设备: repair (or fix) the equipment保养顶驱：service TDS保养冲管：lubricate wash pipe待工日费：standby rate今天零日费：there is no day rate today(zero day rate today)我可以为您做，但必须收费，请理解I can do for you and I have to charge(back charge) you. Please give me full understanding.不在我的职责范围之内，我要汇报领导，一有消息会马上告诉你It is out of my power and I have to report to my boss. I will let you know as soon as I get news.大鼠洞：rat hole小鼠洞：mouse hole钻具错扣：the connections are crossed钻具粘扣：thread is galled丝扣坏了：the thread is damaged起钻错扣：alternate the connections新钻具或接头磨扣：break in the new tool joint新钻头磨合：break in the new bitPDC 钻头井底造型：shape the PDC bit跳钻：rough drilling( vibrated drilling, bit is bouncing)蹩钻：rough drilling（drilling torque is abnormally high）缩径：tight hole起钻遇卡：get overpull下钻遇阻：set weight部分漏失：partially lost circulation全部漏失：totally lost circulation盲钻：blind drilling堵水眼：bit jets are blocked掉水眼：bit jets are lost憋压：the pressure is built up卸压：release pressure试压：pressure test功能测试：function test双方独自检查：double check地质：geology地质专业人员：geologist物理：physics地球物理勘探：geo-physical exploration.测井：logging电测井作业：wireline logging operation泥浆测井：mud logging井（副词“好”含意）：well拓展记忆：井眼：bore hole油气井：oil&gas well试井：well test井下：down-hole井下作业：down-hole operation第2 节石油钻井方法基础词汇钻井原理：the principles of drilling顿钻钻井：percussion drilling，cable-tool drilling旋转钻井：rotary drilling大位移井：big distance( or extended ) well侧钻井：sidetracking drilling水平井：horizontal well探井：wildcat，wildcat drilling深井：deep well浅井：shallow well老井：maturing well丛式钻井：cluster well drilling煤层气井：coal-bed gas well生产井：production well报废井：abandoned well停产井：none-production well井下情况：downhole condition第3 节石油钻井技术基础词汇技术规范，技术指标，技术性能：specification 拉伸：tension拉伸强度：tensile strength弯曲强度：bending srength最小屈服强度：minimum torsional strength 应力：stress压力：pressure应力点：stress point压力降：pressure drop压力梯度：pressure gradient回压：back pressure大气压：atmosphere压差：pressure difference静液柱压力：static fluid cloumn pressure地层压力：formation pressure坍塌压力：collapse pressure破裂压力：fractured pressure液体：liquid固体：solid气体：gas，air正的：positive负的：negative水平的：horizontal垂直的：vertical第4 节石油钻井参数基础词汇钻压：WOB（weight on bit）转盘转速：RPM（rotation per minute）泵压：SPP(slurry pump pressure)泵冲：SPM（stroke per minute）排量：FR(flow rate)大钩负荷：hook load扭矩：torque反扭矩：reactive torque钻速：ROP(rate of penetration)顶驱：TDS(top drive system)钻井周期：drilling period钻井成本：drilling costs井眼尺寸：hole size垂深：TVD(total vertical depth)井深：MD(measured depth)水平位移：horizontal displacement井斜角：angle( or hole inclination)方位角：azimuth井眼环空：annulus第5 节石油钻井作业现场工作人员名称甲方：oil company(operator)钻井承包商：drilling contractor第三方（分包商）the third party(sub-contractor)钻井经理：drilling manager监督：supervisor钻井监督：DSV(drilling supervisor) or Companyman 地质监督：geologist泥浆工程师：mud engineer固井工程师：cementing engineer泥浆录井工：mud logger钻井队：drilling crew，drilling team钻井1 班：drilling shift one总经理：general manager总工程师：chief engineer项目经理：project manager(country manager)作业经理：operation manager财务经理：financial manger会计：accountant平台经理：rig manager带班队长：tool pusherHSE 监督：HSE officer司钻：driller副司钻：assistant driller井架工：derrick man钻工：roughneck（or floorman）场地工：roustabout泥浆工：mudman发动机工：motorman机械师：mechanic电工：electrician电焊工：welder司机：driver吊车司机：crane operator铲车司机：forklift operator营房经理：camp boss医生：doctor材料员：material man(storekeeper)炊事员：cook翻译：interpreter洗衣工：laundry man厨房服务生：waiter保安：watchman(or security)机械工程师：mechanic engineer第6 节石油作业现场常用工具扳手：wrench螺丝起子：screwdriver多角螺丝起子：Phlilips screwdriver （cross-headed screwdriver）撬杠：bar加长撬杠：cheater bar活动板手：monkey wrench，adjustable wrench钳子：pliers钩子：hook台钳：bench vice钢挫：file榔头：hammer锤击扳手：hammer wrench搬手：spanner内六角扳手：Allen key钢锯：hacksaw砂纸：sandpaper管钳：pipe tongs(pipe wrench)链钳：chain tong千斤顶：jack黄油枪：grease gun吊车：crane牵引绳：tag line电焊条：welding rod拖拉机：tractor推土机：bulldozer硬尺：ruler游标卡尺：Vernier slide油漆：paint铅油：dope油漆刷：paint brush铅油刷：dope brush绝缘胶布：electrical tape电线：wire插头：plug电插座：outlet(receptacle or switchboard)开关：switch螺栓：bolt螺帽：nut垫片：washer钉子：nail手电钻：hand drill钻头：bit工作台：workbench工具箱：toolbox胶水：glue胶棒：glue bar护丝：thread protector手轮：hand wheel脚轰油门：throttle联接法兰：coupling flange(or adaptor flange) 安全带：safety belt安全帽：helmet工作靴：safety boot工衣：coverall棉袄：coat防护眼镜：safety goggle手套：gloves口罩：mouth mask围裙：apron洗眼台：eye washing station灭火机：fire extinguisher消防栓：fire -hydrant水龙头：water tap消防斧：fire fighting axe铲子：shovel手砂轮：emery wheel左转：turn left右转：turn right手势：gesture信号：signal垃圾：waste garbage拖把：mop接头：sub配合接头：X-over ，cross-over提升短节：lifting sub卡瓦：slips放卡瓦：set slips母锥：box tap公锥：taper tap打捞矛：fishing spear安全接头：safety sub柔性短节：flexible joint井口盖子：wellhead cover防喷盒：mud boxBOP 吊装：BOP trolley( BOP hoist)吊卡：elevator吊环：elevator links安全卡瓦：safety clamp(dog collar)钻杆架：pipe rack水龙头提环：swivel bail材料房：warehouse绳卡：bullnose clamp(guy anchor)绳套：sling吊带：soft sling(belt)卸扣：shackle吊装工具：lifting gear维护保养：maintenance内钳：make-up tong外钳：break-out tong液压大钳：power tong液压猫头：E-zy tong兜绳：mule line四通阀：four-way valve三通：Tee软管：hose球阀：ball valve闸板阀：gate valve单流阀：back valve灌注泵：supercharge pump第二章：石油工程常用设备及专业术语第1 节钻井设备部分井架：Derrick(or mast)起（放）井架：erect(lay down) Derrick 底座大梁：sill钢木基础：mat铅锤：plumb水平仪：level架，台：rack立根盒：setback area坡道：V door(or ramp)猫道：catwalk二层台：monkey-board圆井盖：cellar cover天车：crown block防碰天车：crown-o-matic天车梁：crown block beam天车台：water table游动滑车：traveling block钻井大绳：drilling line引绳：guide line穿大绳：string-in drilling line金属线，电线：wire，cable钢丝绳股：strand截断：cutoff滑车，滑轮，皮带轮：pulley(hoist)手拉葫芦：hand pulley吊耳：lifting eye顶驱：top drive大钩：hook大钩弹簧：hook spring大钩销子：hook pin大钩锁紧装置：hook locking device大钩悬挂高度：hook height水龙头：swivel鹅颈管：gooseneck冲管：wash pipe水龙头盘根：swivel packing钻井水龙带: rotary hose( kelly hose)立管：stand pipe立管管汇：stand pipe manifold高压管线：high pressure line由壬：union低压管线：low pressure line传感器：sensor放压管线：relief line转盘：Rotary Table转盘方瓦：master bushing方补心取出装置：bushing handling tool 方补心：kelly drive bushing方孔：square opening小鼠洞：mouse hole大鼠洞：rat hole绞车：Drawworks挂合（摘开）绞车：engage(disengage) drawworks液压绞车：hydraulic winch气动绞车：air tugger(air hoist)滚筒：drum( reel)滚筒高速气离合器：high speed clutch滚筒低速气离合器：low speed clutch锚头：cathead液压猫头：E-zy tong上扣猫头：make up cathead卸扣猫头：make out cathead牙嵌离合器：jaw clutch涡磁刹车：eddy current brake(electromagnetic brake) 猫头轴：cathead shaft猫头绳：cathead line死绳：dead line死绳固定器：dead line anchor间隙：gap死绳固定器膜片：dead line diaphragm上扣：make up上扭矩：torque sth卸扣，卸开：break out上紧，固定：tighten（fasten）松开，松扣：loosen加载：load卸载：unload盘式刹车：disc brake刹车总成：brake assembly刹车轴：brake shaft刹车带：brake band刹车片：brake block液压油箱：hydraulic power unit液动试压泵：hydraulic test pump液压大钳：hydraulic （power）tong倒档齿轮：reverse gear动力扳手：power wrench吊钳钳头：hinged jaw钳牙：die大钳锁销：latch大钳悬臂：suspension bar平衡重：counterbalance weight吊钳钳臂：tong arm第2 节钻井泵类及相关设备泥浆泵：mud pump活塞：piston活塞杆：piston rod活塞皮碗：piston cup缸套：liner凡尔体：valve body凡尔座：valve seat凡尔箱：pump module阀弹簧：valve spring阀杆：valve lever阀面：valve face阀帽：valve bonnet空气包：pulsation damper充氮气：refill with nitrogen泥浆泵安全阀：pop-off valve卸压管线：release line排出阀：discharge valve吸入阀：suction valve上水滤子：screen油尺：oil-level dipstick灌注泵：supercharge pump冷却水泵：cooling pump潜水泵：submersible pump盘根盒：stuffing box叶轮：impeller单向阀：check valve（single-pass valve）安全阀：safety valve手动阀：manual valve液动阀：hydraulic valve拉杆：tie rod，tension bar压力表：pressure gauge冲数：strokes排量：flow rate80 冲(次)/分：eighty strokes per minute 泥浆罐：mud tank倒泥浆：transfer mud循环罐：active tank储备罐：reserve tank起下钻罐：trip tank溢流检查：flow check沉砂罐：satteling tank锥形罐：sand trap震动筛：sahle shaker筛布：screen目数：mash除砂器: desander除泥器: desilter离心机：centrifuge泥浆分配槽：spider box缓冲罐buffer tank第3 节与泵操作有关的实用短语没有压力：No pressure压力过高：The pressure is too high返回太少：Mud return is too few水太少：Water is not adequate.抢修：Rush to repair请看记录：Please check the record没作记录：No record available加化学药品：add chemicals测定比重：measure mud weight(specific gravity) 测定失水：measure water loss泥饼：mud cake测定切力：measure gel strength停泵：stop pump请打手势：Please make a gesture转动一周：turn round a circle垫高一些：put something under it to raise抓紧：firmly grasp抬高：lift it up拿稳：hold firm打一下：hit once往外拉：pull outward站稳：stand firm小端：small end大端：large end光滑：smooth粗糙：coarse，rough平面：flat弯曲：bending放松：loosen绷直：stretch tight，draw tight冷却：cooling润滑：lubricate过载：overload功率不足：power is not enough.第4 节钻台与底座钻台：drilling floor钻井班组记录：drilling tour record司钻监视器：driller's monitor司钻控制台：driller's console指重表：weight indicator底座：substructure井队活动房：trailer钻台上值班房：doghouse梯子：ladder第5 节井控操作与防喷器溢流: kick溢流征兆: kick sign气侵：gas cut井喷：blow-out1 次井控the primary well control2 次井控the secondary well control3 次井控the tertiary well control平衡balance超平衡over-balance欠平衡under balance漏失试验leak-off test破裂压力fracture pressure额定压力rated pressure工作压力working pressure防喷器组BOP stack安装（甩下）防喷器组：nipple up(nipple down) BOP stack 分流器diverter万能防喷器：annular preventer，bag preventer单闸板防喷器：single ram preventer双闸板防喷器：double ram preventer（防喷器）闸板：pipe ram变芯闸板防喷器variable bore ram全封式防喷器：blind ram剪切防喷器：shear ram内防喷器Inside BOP投入式单流阀DIBPV（Drop in blowout preventer valve）分流关线diverter line节流管汇choke manifold节流阀choke valve旁通阀standby valve调压阀: Pressure regulator手动节流阀manual choke远程节流阀remote choke井口四通drilling spool变径法兰：adapter flange液压控制阀HCR(hydraulic controller)远程控制系统：koomey unit蓄能器：accmulator压井管线：kill line入口：inlet出口：outlet简易除气器：poor-boy degasser真空除气器：vaccum degasser泥浆池液面纪录仪Pit volume recorder(totallizer) 泥浆流动传感仪mud flow sensor泥浆增量Pit gains硫化氢侵入H2S influx加重材料Weighted material氮气Nitrogen乙炔：acetylene氧气：oxygen预冲氮气压力Pre-charge nitrogen pressure地脚螺栓连接Studded connection法兰连接Flange connection箍盘连接Hub connection演习：drill急救演习：first aid drill消防演习：fire drill防喷演习：kick drill泄压: bleed off pressure带刻度压力表: calibrated pressure gauge带刻度容（体）积表: calibrated volume gauge 套管鞋: casing shoe上部井眼段top hole section快速钻进地层fast drilling formation压实地层：consolidated formation风化地层：weathered formation钻屑携带能力cuttings carrying capacity浅层气藏shallow gas地层破裂formation to break down压力梯度pressure gradient地层压力formation pressure井口压力wellhead pressure漏失压力leak-off pressure破裂压力fractured pressure井底压力BHP( bottom hole pressure)正常压力normal pressure异常压力abnormal pressure静液压力hydrostatic pressure动态压力dynamic pressure环空压力annular pressure关井钻杆压力SIDPP (shut in drill pipe pressure)关井套管压力SICP( shut in casing pressure)最大关井套管压力maximum allowable surface pressure, MAASP 最初循环压力ICP( Initial circulating pressure)循环结束压力FCP(Final circulating pressure)U 形管原理U-tube principle压井操作killing operation补救措施remedial actions关井后循环circulation under well closed in conditioncl 离子含量chloride contentDc 指数Dc exponent软关井soft shut in硬关井hard shut in第1 次循环first circulation第2 次循环second circulation压井泥浆比重kill mud weight抽吸swab激动surge含气地层gas bearing formation含气页岩gas bearing shale安全增量safety margin记录卡片trip sheet低循环泵速SCR(slow circulation rate)当量泥浆密度EQD(equivalent mud density)当量循环密度ECD(equivalent circulating density)司钻压井法driller’s method等待压井法wait & weight method体（容）积法volumetric method下推压井法bull-heading method不压井下钻：snub in第三章：钻井工程作业部分第1 节钻井事故井喷：blow out井涌：kick井漏：lost circulation坍塌，井壁坍塌：cave in(collapse)出砂：sand production砂桥：sand bridge台阶：ledge键槽：keyseat椭圆井眼：oval shaped hole卡钻：sticking填井：pack-hole封井：packed drilling井下落物：fish大幅度活动钻具试图解卡：work the string and try to free it活动钻具以避免卡钻：move(reciprocate ) the string to avoid being stuck. 打捞：fishing鱼头：top of fish打捞工作：fishing job侧钻：side-tracking侧钻井眼：sidetracking hole水泥窜槽：cement channeling固井失败：cement failure防砂：sand control缓慢开泵并仔细观察返浆情况：slowly start pumping and closely watch the return on the shale shaker第2 节钻头牙轮钻头：rock bit刮刀钻头：drag bit金钢石钻头：diamond bit镶齿钻头：insert bit铣齿钻头：milled tooth bit喷射钻头：jet bit牙轮：cone钻头装卸器：bit breaker钻头直径：bit diameter钻头寿命：bit life钻头磨损：bit wear钻头型号：bit type水眼尺寸：nozzle size水眼效率：nozzle efficiency钻头接头：bit sub第3 节钻具方钻杆：kelly方钻杆旋扣器：kelly spinner方钻杆旋塞：kelly cock钻具：drilling string钻杆：drill pipe油管：tube钻具组合：drilling assembly扶正器：stabilizer扩眼器：reamer（hole opener）钻铤：drill collar无磁钻铤：NMDC(non-magnetic drill collar) 加重钻杆：HWDP(heavy weight drill pipe) 近钻头扶正器：near-bit stabilizer震击器：jar减震器：shock absorber螺旋钻铤：spiral drill collar键槽破坏器：key seat reamer安全接头：safety joint钻杆刮泥器：drill pipe wiper泥浆动力钻具：mud motor钻柱：drill string涡轮：turbine涡轮钻具：turbo-drill stem立根：stand加厚：upset内加厚：IU(internal upset)外加厚：EU(external upset)内外加厚：internal-external upset丝扣：thread打捞颈：fishing neck母扣：box公扣：pin左旋螺纹：left-hand thread右旋螺纹：right-hand thread正规接头：regular joint贯眼接头：full hole joint内平接头：internal flush joint护丝：thread protector快速护丝：easy protector打捞工具：fishing tool打捞作业：fishing operation打捞篮：junk basket卡瓦打捞筒：overshot打捞杯：junk sub牙轮打捞器：cone fisher套管打捞矛：casing spear打捞矛：fishing spear打捞公锥：male tap(fishing nipple)打捞母锥：female tap(fishing socket)倒扣工具：reversing tool(backing-up tool) 铣鞋：milling shoe铣具：milling tool平底铣鞋：flat bottom mill磁力打捞工具：magnetic fishing tool打捞钩：fish hook气动工具：pneumatic tool减摩短节：friction reduction sub下套管漂浮接箍：casing floating coupling轴向加压器：hydraulic axial thruster第4 节钻井工程地面作业实用词汇与短语方入：kelly-in方余：kelly-up开钻：spud in作业指令：instruction钻井设计：drilling program井身结构：well schematic岩性：lithology迟到时间：lag time(bottom up)换钻头：change bit甩钻具：laydown drill pipe发生故障：break down安装（拆卸）：rig up(rig down)接头：sub adapter机械手：mechanical arm铁钻工：iron roughneck有故障：It fucked up( something is wrong with it)已修好：it has been fixed马上去：Go there at once请下去：Please go down请上来：Please come up躲开，危险：keep away，danger.请翻译来：Ask interpretor come here，冲洗：wash down井口：well-head一根钻杆（单根）：single三根钻杆组合（立根）：thribble吊蓝：cage(basket)换班：shift change第5 节钻井工程井口作业实用词汇与短语喇叭口：bell nipple出水管：mud return line(flow line)试压杯：cup tester小心滑倒：wet floor, be careful不要往井眼内掉东西：never fall down anything inside hole我来做：Let me do it带把板手来：Bring a spanner，please带点密封剂：Bring a little sealant(Teflon)，please 很快就好了：lt will be finshed right away抬一下：Let's lift it把绳子给我：Give me the rope，please不漏：no leakage电焊：welding气焊：gas welding气割：gas cut栏杆：handrail，gangway rail，railing蒸汽：vapour压缩空气：pressurized (compressed) air注意安全：pay attention to safety别动：Don't move，Don't touch.对准：point out exactly.校正：align裸眼：open hole第四章：钻井液及相关设备第1节钻井液名称泥浆：mud钻井液：drilling fluid完井液：completion fluid修井液：work-over fluid压井液：killing fluid射孔液：perforating fluid隔离液：spacer fluid泥浆处理：mud treatment泥浆处理设备：mud treating equipment饱和盐水泥浆：saturated salt-water mud油基泥浆：oil-base mud高粘度泥浆：heavy viscous mud重泥浆：weighted mud重泥浆压钻杆：slug drill pipe起钻倒返泥浆：we have wet pipeduring POOH重晶石：barite纯碱：soda ash高岭土粉：koaline powder云母片：mica sheet增粘剂：viscosifier稀释剂：diluent (thinner)稳定剂：stabilizer (stabilizing agent)烧碱：caustic soda稀释dilution, thinning水泥凝固cement setting第2 节钻井液设备离心泵：centrifugal pump振动筛跑泥浆：mud overflow shale shaker 筛出：shake out混合泵：mixing pump混合漏斗：mixing hopper搅拌器：mud agitator泥浆抢：mud gun岩屑：cuttings沉淀：settle沉积物：deposit吸入：suction吸入罐：suction pit泥浆天平：mud balance游码：slide weight支点：fulcrum刀口：edge调整，校正：adjust粘度计：viscometer第3 节钻井液处理剂包，袋：sack粘土：clay膨润土，般土：bentonite钠：sodium钙：calcium氯：chloride氯化钙：calcium chloride石棉：asbestos分散：dispersal表面活性剂：surface-active material铁络盐：lignite单宁：tannin羧甲基纤维素：carboxymethyl celluose CMC 木纤维：xylogen石灰：lime二氧化钙：calcium oxide粉末：powder薄片：flake溶解：dissolve延迟，妨碍：retard处理剂，添加剂：additives缓凝剂：retarder支撑剂：proppant乳化剂：emulsifier润湿剂：wetting agent稳定剂：stabilizing agent除钙剂：calcium remover降失水剂：filtration-reducing agentPH 值控制剂：PH control additive润滑剂：lubricant消泡剂：defoamer agent破乳剂：emulsion breaker洗涤剂：detergent防膨胀剂：anti-swelling agent粘土稳定剂：clay stable agent稀释剂：thinner封堵剂：plugging agent抑制剂：inhibition agent暂堵剂：temporary plugging agent解堵剂：plugging removal堵漏剂：LCM (lost circulation material)水敏地层：water-sensitive formation分散：dispersal水泥浆：cement slurry流变性：rheological characteristics稳定性：stability稠化时间：thickening-time低密度水泥浆：low-density slurry油气层保护：reservoir protection高渗透性：high-permeability砾石：gravity悬浮：suspension固化：solidification.防膨胀：anti-swelling高凝高粘度：high condensation and viscosity 无毒的：non-poisonous无荧光：non-fluorescence钻井液性能参数Specificaitons of Drilling Fluid 含水：water content密度：density厚度：thickness粘度：viscosity塑性粘度：plastic viscosity含砂量：sand content屈服：yield屈服点：yield point屈服强度：yield strength剪切速率：shear rate剪切强度：shear strength剪切应力：shear stress稀释：dilute适用温度：safe temperature初始切力：initial gel strength终切力：ten-min gel strength触变性：thixotropy剪切稀释：shear thining液体浓度:concentration泥浆柱：mud column层流：laminar flow涡流：turbulent flow气泡：bubble第五章：钻井相关作业第1节取芯部分岩心：core取心钻头：core bit取心筒：core barrel内岩心筒：inner barrel外岩心筒：outer barrel岩心爪：core catcher取心工具：corehandling tools取心收获率：core recovery rate 取样器：sample blob取样盒：sample box样品筒：sample chamber取样工：sample catcher取样间隔：sample interval井壁取心：side-wall coring井壁取心枪：side-wall coring gun 取芯失败：coring failure第2 节固井部分固井：cementing完井：well completion水泥：cement井口：wellhead井口压力：well head pressure井口回压：back pressure on the well head套压：casing pressure导管：conductor表层套管：surface casing技术套管：protective casing(intermediatecasing) 油层套管：production casing尾管：liner尾管悬挂器：liner hanger通径轨：rabbit封隔器：packer联顶节：landing joint套管柱casing string套管下部结构(含套管鞋、浮箍)：casing track(including casing shoe, float collar) 套管扶正器：centralizer止退环：stop collar口袋：pocket( rat hole)环空注水泥作业：top cement job碰压：bump plug隔离液：spacer分级箍：stage collar水泥粘结强度strength of cement bond套管钳：casing tongs套管接箍：casing coupling套管头：casing head散装水泥：bulk-cement水泥浆：cement slurry插管注水泥：stab in cementing插入密封接头：stab in adapter分级注水泥：stage cementing先行水泥浆：lead cement slurry末端水泥浆：tail cement slurry促凝剂：accelerator替浆：displace with mud水泥面：top of cement固井管线：chicksan line(cementing line)灰罐：silo(bulk tank)候凝：WOC(wait-on-cement)挤水泥：squeeze cement水泥塞：plug第3 节固井水泥浆名称和参数超细水泥浆：ultrafine slurry普通水泥浆：normal slurry纤维水泥浆：fiber-reinforced cement slurry膨胀水泥浆：expanding cement slurry低密度水泥浆：low-density slurry水泥体积收缩：cement volume contraction水泥浆水化期间：cement slurry hydrating period水泥胶结质量：cement sheath bonding quantity失水率：the rate of water loss析水：liberate water稠化时间：thickening time凝固强度：cementation strength渗透性：permeability，膨胀率：expansion rate压缩强度：compression strength流动性：mobility第4 节测井部分电测：wireline logging测井解释：logging interpretation随钻测井：LWD(logging while drilling)测井电缆：logging cable测井工具：logging tool自然电位测井：spontaneous potential log感应电测井：induction electrical survey双感应测井：dual induction-laerolog中感应测井：medium induction log数字记录：digital record照相记录：photographic recording放射性测井：radioactivity log声波技术：acoustic wave technology仪器耐温：the temperature resistance of the instrument 仪器耐压：pressure resistance of instrument油气比：GOR (gas oil ratio)第六章：井下作业常用短语修井：work-over修井工具：work-over tool井下操作：down-hole operations.产层污染：pollution of pay zone增产措施：stimulations压裂和酸化：fracturing or acidizing酸化处理：acid treatment人工压裂：artificial fracturing重复压裂过程：repetition presses for fracturing，压裂车：fracturing truck sets压裂后反映：post-fracture response固体和液体添加泵：solid and liquid additive pump泵交联：pumping cross link交联剂：cross-linking agent排量：discharging三维压裂：three-dimension fracturing对压裂参数的监控、分析和解释：real time monitoring，analyzing and interpreting for fracturing operation parameters压裂操作：fracturing operation压裂规模：fracturing scale化学吞吐：chemical disposal乳化降粘：emulsification declining viscosity增注：augmented injection.注水：water-injection裸眼砾石填充完井：bore hole gravel packer completion.开窗铣锥：open-window mill prick，开窗斜向器：open-window inclined implement碳酸盐岩：carbonate reservoir第七章：海上钻井作业¨海上钻井：offshore drilling陆地钻井：on-land drilling海滩：sea beach浅海：shallow sea海底管线：sea-bottom pipe海底电缆铺设：setting cable under sea-bottom平台安装：platform installation钻井平台：drilling platform顺风：tail wind逆风：against the wind摄氏零下…度：below…degree centigrade启锚：weigh anchor抛锚：drop anchor拖航：drag对讲机：intercom，walkie-talkie上吊茏：Please get on the liftbasket救生衣：life jacket晕船：sea sick控制速度：Control the speed货已送抵：The goods has arrived货物验收：Please check and accept the goods在不远处：Not far from here不方便：lt's not convenient有危险：lt's dangerous防污染：prevent pollution没情况：Nothing happened.第八章：定向井部分定向井：directional well造斜点：ＫＯＰ（kick off point）最大井斜角：maximum hole inclination增斜段：building up section稳斜段：holding section降斜段：drop off section井眼尺寸：hole size长、中、段半径：long，medium and short radius 裸井段：the open hole section水平段：horizontal section固井段：cementing section井斜角测量点：angle point水平位移：horizontal departure(displacement)井眼轨迹：wellbore trajectory优化控制：optimum control筛管：screen pipe长封固段固井：long intervals cementing丛式井：cluster well斜向器：whipstock第九章：石油现场机械传动与机械设备第1 节：动力与传动柴油机：diesel发电机：generator直流（交流）电动机：DC（AC）motor交流电：A.C （alternating current）直流电：D.C （direct current）变压器：transformer传动轴：driving shaft从动轴：driven shaft空调机：air conditioner空气压缩机：air compressor应急发电机组：emergency generator消防水泵：fire pump配电间：distrubution room电动潜水泵：ESP(electrical submersible pump) 锅炉：boiler蒸汽：vapour气压不足：The airpressure is poor操作有问题：Operation is not good电压正常：Voltage is all right绝缘不好：The insulation is bad触电：electric shock温度太高：The tempreture is too high 接地：ground短路：short circuit按红色钮：Please push the red button 打开：open，turn on，switch on关闭：close，turn off，switch off风扇：fan爬上去：climd up跳下来：jump down接住：catch it拿稳：hold tight平方米：square meter立方米：cubic meter加工：process三项交流电：three-phase AC气罐：air tank偶合器，联轴节：coupling链轮：sprocket链条：chain皮带：belt链条驱动：chain drive皮带驱动：belt drive第2 节机械加工与设备对准，使…成一线：align周围的，环境的：ambient模糊，含糊，不明确：ambiguity退火的：annealed淬火：quench回火：temper阳极：anode阴极：cathode含水的，水的：aqueous装配：assembly增大，增加，增益：augment侧向间隙：back-lash电木，（绝缘）胶木：Bakelite批量生产：bulk production轴承：bearing锥齿轮，伞齿轮：bevel gear（刮刀，刃，叶片：blade坯料：blank吹风，爆炸，喷砂机：blast滑轮组：block and tackle浮子，摆锤：bob镗床，镗孔刀具：borer内孔加工，镗孔：boring瓶颈，薄弱环节：bottleneck平衡点，盈亏临界点：breakeven point 型坯：briquette拉床，铰孔机：broacher拉削，扩孔：broaching大齿轮：bull gear碰撞，曲折，拐点：bump缓冲器，减震器：bumper擦亮，光亮：burnish去毛刺：burring凸轮，偏心轮：cam凸轮轴：camshaft铸造：cast触媒，催化剂：catalyst空化作用：cavitation内腔，空穴，（铸造）型腔：cavity陶瓷的，陶器的，陶瓷制品：ceramic铁屑，金属屑：chip凿子，扁铲：chisel钳：clamp障碍（物），阻塞（物）：clog离合器：clutch罗盘，指南针：compass凸型的：convex凹型的：concave外形，轮廓；结构，构造：configuration 锥形的，锥状的，锥体：conical传送装置，运输机，传送带：conveyor 波纹；使成波状：corrugation曲柄，曲拐：crank曲轴：crankshaft蠕动，蠕变：creep圆筒，圆柱体；液缸:cylinder仪表盘，控制板：dashboard静载：dead load碎片：debris模具，钢型，冲模：die模锻：die forge压铸的，模铸的：die-cast不导电的，电解质（的）：dielectric差动齿轮，差速齿轮：differential gear扩散，弥漫：diffusion修饰，打磨，使表面光洁：dress钻床：drill press染色，着色；染料：dye电解质：electrolyte椭圆，椭圆体：ellipse金刚砂：emery侵蚀，冲蚀：erosion蚀刻：etch排出，排气；废气：exhaust消音器：muffler爆炸物，炸药；爆炸（性）的：explosive挤压（成形）；挤出，压出：extrude平面加工：facing测隙规：feeler gauge膜：film精加工：finish柔性的，能变形的，灵活的，适应性强的：flexible软盘：floppy disc硬盘：hard disk车床：lathe流程图：flow chart起伏，波动：fluctuation开槽，切槽：fluting飞轮：flywheel锻造：forge支点，支轴：fulcrum（龙门）起重机：gantry几何学：geometry花岗岩，花岗石：granite石墨：graphite润滑脂：grease磨碎，研磨，磨削加工：grinding槽，沟，企口：groove陀螺仪，回转仪：gyroscope主轴箱：headstock螺旋形的，螺线：helical螺旋齿轮，斜齿轮：helical gear六角形（的）：hex万向接头，万向联轴节：hooke (cardan) joint,flexible joint 削弱，损害：impair冲击，脉冲：impulse。
石油行业常用英语词汇(全面)
石油行业常用英语词汇（全面）1. 石油勘探（Petroleum Exploration）Seismic survey：地震勘探Exploration well：探井Reservoir：储层Porosity：孔隙度Permeability：渗透率2. 钻井与完井（Drilling and Completion）Drilling rig：钻机Bit：钻头Drill pipe：钻杆Casing：套管Cementing：固井Completion：完井Fracking：水力压裂3. 采油与生产（Oil Production and Extraction）Production well：生产井Pumpjack：抽油机Artificial lift：人工举升Separator：分离器Flowline：输油管线Tank farm：储油罐区4. 石油加工（Petroleum Refining）Crude oil：原油Refinery：炼油厂Distillation：蒸馏Cracking：裂化Catalytic reforming：催化重整Asphalt：沥青Lube oil：润滑油5. 石油产品（Petroleum Products）Gasoline：汽油Diesel：柴油Jet fuel：航空煤油Fuel oil：燃料油Petrochemicals：石油化工产品6. 安全与环保（Safety and Environmental Protection）HSE（Health, Safety and Environment）：健康、安全与环境 Spill：泄漏Emission：排放Waste treatment：废物处理Environmental impact assessment：环境影响评估7. 国际合作与市场（International Cooperation and Market）OPEC（Organization of the Petroleum Exporting Countries）：石油输出国组织Brent crude：布伦特原油NYMEX（New York Mercantile Exchange）：纽约商品交易所Spot market：现货市场Futures contract：期货合约本文档为您提供了石油行业常用英语词汇的全面梳理，希望对您的工作和学习有所帮助。
石油专业英语复习资料
石油专业英语复习资料Section 1Petroleum 石油Drilling 钻井Kelly 钻杆String 管汇、管柱Drill pipe 钻杆BHA(Bottom Hole Assembly) 底部钻具组合Sub/joint 接头Collar 钻铤Bit 钻头Finger bit 刮刀钻头Toothed bit 牙轮钻头Diamond bit 金刚石钻头DC 钻铤DS 钻柱Section 2Cat walk 猫道、滑道Cat head 猫头dog house （司钻）休息室、值班室dog leg 狗腿goose neck 鹅颈管monkey board 猴台（二层台）rat hole 大鼠洞mouse hole 小鼠洞fish 落鱼fishing 打捞kick 井涌BOP 防喷器KOP 造斜点Section 3Straight well 直井Directional well 定向井Horizontal well 水平井Extended reach well 大位移井Superdeep well 超深井Underbalance drilling 欠平衡钻井Casing drilling 套管钻井Drilling operations 钻井操作Make a trip/tripping 起下钻Trip up/out 起钻Trip in/down 下钻Make a connection 接单根Completion 固井Completion 完井Logging 测井、录井Derrick system 起升系统Rotary system 旋转系统Draw works 绞车Rotary table 转盘Circulating system 循环系统Muclpump 钻井泵Section 4 Hoisting system 起升系统1 Crown block 天车Traveling block 游动滑车（游车）Hook 大钩Wire line 钢丝绳Derrick 井架2 The type of derrick 井架类型Pyramid derrick 塔式井架Self-elevating derrick 自升式井架Cantilever derrick 前开口井架A-mast derrick A形井架W-mast derrick 桅形井架3 The draw works 绞车刹车Main brake 主刹车Assist brake 辅刹车Band brake 带式刹车Disc brake 盘式刹车Electromagnetic brake 电磁刹车Eaton brake 伊顿刹车Brake band 刹车带Brake drum 刹车筒Pitman 连杆Brake handle 刹把Brake block 刹车块Hydraulic disc brake 液压盘刹Section 5 The rotary system 旋转系统1 Rotary table 转盘Turntable 转台Master bushing 方补心Swivel 水龙头Top drive 顶驱Rotary hose 水龙带Standpipe 立管2 三管goose neck 鹅颈管wash pipe 冲管base pipe/center pipe 中心管3 三轴承main bearing 主轴承upper alignment bearing 上扶正轴承lower alignment bearing 下扶正轴承4 四密封upper machine oil seal 上机油密封lower machine oil seal 下机油密封upper drilling fluid seal 上钻井液密封lower drilling fluid seal 下钻井液密封section 6 The drilling fluid 钻井液1 Mud 泥浆Slurry 水泥浆2 The drilling fluid 钻井液Water base drilling fluid 水基钻井液Oil base drilling fluid 油基钻井液Oil-in water 水包油Water-in-oil 油包水Synthetic drilling fluid 合成基钻井液3 Liquid phase 液相Water 水Oil 油4 Solid phase 固相Clay 粘土Adulterant 加重剂Treating chemical 化学处理剂5 Bentonite 搬土Barite 重晶石Sang content 含砂量Solid phase content 固相含量Colloid 胶体Emulsion 乳状液Foam 泡沫Density 密度Viscosity 粘度Shear 切力Filtration 滤失Viscometer 粘度计Filter press 失水仪Density meter 密度计Section 7 The rig personnel 井队人员编制The rig personnel 井队人员编制Tool pusher 队长Assistant tool pusher 副队长Diller 司钻Secretary 书记assistant diller 副司钻derrickman 井架工roughneck 钻工beach worker 钳工mud man 泥浆工section 8 power and drive system 动力驱动系统1 Power and drive system 动力驱动系统Diesel engine 柴油机Current 电源DC(direct current) 直流电AC(alternating current) 交流电2 The plane of drive 驱动方式Unity drive 统一驱动Unit drive 单独驱动Subunit drive 分组驱动3 Power equipment 驱动设备Mechanical drive 机械驱动Electric drive 电驱动Combination drive 复合驱动Section 9 the actuating system 传动系统1 Type of actuating 传动类型Belt 胶带、皮带Chain 链条Gear 齿轮2 Belt rig 胶带钻机Chain rig 链条钻机Gear rig 齿轮钻机3 Hygraulic drive 液压传动Hygrodynamic drive 液力传动Electric drive 电传动4 Braking 减速Paralleling 并车Astern 倒车Shift 变速Section 10 the control system 控制系统1 The control system 控制系统Air control 气控Air feeder 供气设备Executive element 执行元件Control element 控制元件Assistant element 辅助元件2Air feeder供气设备Air compressor 空气压缩机Air tank 储气罐Air purification equipment 空气净化设备3Excutive element 执行元件Cylinder 气缸Air motor 气马达Air drive friction clutch 气动摩擦离合器Control element 控制元件Pressure control valve 压力控制阀门Temperature control valve 温度控制阀门Flow control valve 流量控制阀门4 Assistant element 辅助元件Antiflocculant 防凝器Alarm 报警器Potating joint 旋转接头Fitting 管汇、管件Section 11 The sub structure system 底座系统1 drilling floor 钻台Derrick 井架Drawworks 绞车Roary table 转盘Pipe setback 立根盒Wellhead tod 井口工具Driller” console 司钻控制台2 control room 机房Power package 动力机组Actuating equipment 传动机组Section 12 The assistant system 辅助系统1Blowout preventer(BOP) 防喷器Kick 井涌、溢流Blowout 井喷Well control 井控Shut well in 关井Kill the well 压井2 BOP 防喷器Rotary BOP 旋转防喷器Annulus BOP 环形防喷器Double ram type BOP 双闸板防喷器Spool 四通Ram type BOP 单闸板防喷器。
(完整版)石油钻井工程英语词汇
石油钻井工程英语词汇2008-10-15第一章：石油钻井工程英语基础词汇第1 节石油钻井工程基础词汇钻井：drill定向斜井：directional drilling欠平衡钻井：under-balance drilling海上钻井：off-shore drilling陆地钻井：on-shore drilling钻头：drill bit刮刀钻头：drag bit牙轮钻头：rock bit (镶齿钻头insert bit, 钢齿钻头steel toothed bit) 金刚石钻头：diamond bit取心钻头：coring bit钻头浮阀：float valve钻头水眼：bit nozzle(or jet)钻头水眼刺:bit nozzle washed out钻头规：bit caliper(bit gauge)钻头泥包：bit is balling钻头钝了，我建议现在起钻：bit is dull. I suggest to POOH now地址：北京市朝阳区东三环中路7号财富中心A座601 邮编：100020钻铤：DC(drill collar )光钻铤slick drill collar，螺旋钻铤spiral drill collar钻杆：DP(drill pipe )方钻杆：kelly公扣：pin end母扣：box end内平式连接：IF(internal flash)正规式连接：REG(regular)贯眼式连接：FH(full hole)加重钻杆heavy weight drill pipe短钻杆pop joint井下马达：downhole motor涡轮钻具：turbine震击器：drilling jar减震器：absorber下部钻具组合：BHA（bottom hole assembly）钻具扶正器：stabilizer（string stabilizer, near-bit stabilizer）钻机：drill rig钻井泥浆：drilling mud钻井液：drilling fluid钻井设备：drilling equipment油：oil原油：crude oil天然气：nature gas煤层气：coal-bed gas石油：petroleum中国石油（简称）：CNPC（China National Petroleum Corporation ）长城钻井（简称）：GWDC(Great Wall Drilling Company)采油：oil production产油层(目的层)：reservoir( or pay zone)钻进：drilling调整钻井参数以得到理想的机械钻速：play the drilling parameters to get fast ROP起钻：POOH(pull out of hole)下钻：RIH(run in hole)下套管：run casing(or RIH with casing)短起下钻：wiper trip循环泥浆：circulate泥浆：reverse circulate中途循环泥浆：break circulation分段下钻：RIH in stages通井：control trip划眼：reaming倒划眼：back reaming接单根：make connection滑、割大绳：slip and cut drilling line by ton-mile保养设备：maintain the equipment修理设备: repair (or fix) the equipment保养顶驱：service TDS保养冲管：lubricate wash pipe待工日费：standby rate今天零日费：there is no day rate today(zero day rate today)我可以为您做，但必须收费，请理解I can do for you and I have to charge(back charge) you. Please give me full understanding.不在我的职责范围之内，我要汇报领导，一有消息会马上告诉你It is out of my power and I have to report to my boss. I will let you knowas soon as I get news.大鼠洞：rat hole小鼠洞：mouse hole钻具错扣：the connections are crossed钻具粘扣：thread is galled丝扣坏了：the thread is damaged起钻错扣：alternate the connections新钻具或接头磨扣：break in the new tool joint新钻头磨合：break in the new bitPDC 钻头井底造型：shape the PDC bit跳钻：rough drilling( vibrated drilling, bit is bouncing)蹩钻：rough drilling（drilling torque is abnormally high）缩径：tight hole起钻遇卡：get overpull下钻遇阻：set weight部分漏失：partially lost circulation全部漏失：totally lost circulation盲钻：blind drilling堵水眼：bit jets are blocked掉水眼：bit jets are lost憋压：the pressure is built up卸压：release pressure试压：pressure test功能测试：function test双方独自检查：double check地质：geology地质专业人员：geologist物理：physics地球物理勘探：geo-physical exploration.测井：logging电测井作业：wireline logging operation泥浆测井：mud logging井（副词“好”含意）：well拓展记忆：井眼：bore hole油气井：oil&gas well试井：well test井下：down-hole井下作业：down-hole operation第2 节石油钻井方法基础词汇钻井原理：the principles of drilling顿钻钻井：percussion drilling，cable-tool drilling 旋转钻井：rotary drilling大位移井：big distance( or extended ) well侧钻井：sidetracking drilling水平井：horizontal well探井：wildcat，wildcat drilling深井：deep well浅井：shallow well老井：maturing well丛式钻井：cluster well drilling煤层气井：coal-bed gas well生产井：production well报废井：abandoned well停产井：none-production well井下情况：downhole condition第3 节石油钻井技术基础词汇技术规范，技术指标，技术性能：specification拉伸：tension拉伸强度：tensile strength弯曲强度：bending srength最小屈服强度：minimum torsional strength应力：stress压力：pressure应力点：stress point压力降：pressure drop压力梯度：pressure gradient回压：back pressure大气压：atmosphere压差：pressure difference静液柱压力：static fluid cloumn pressure地层压力：formation pressure坍塌压力：collapse pressure破裂压力：fractured pressure液体：liquid固体：solid气体：gas，air正的：positive负的：negative水平的：horizontal垂直的：vertical第4 节石油钻井参数基础词汇钻压：WOB（weight on bit）转盘转速：RPM（rotation per minute）泵压：SPP(slurry pump pressure)泵冲：SPM（stroke per minute）排量：FR(flow rate)大钩负荷：hook load扭矩：torque反扭矩：reactive torque钻速：ROP(rate of penetration)顶驱：TDS(top drive system)钻井周期：drilling period钻井成本：drilling costs井眼尺寸：hole size垂深：TVD(total vertical depth)井深：MDD(measured depth)水平位移：horizontal displacement井斜角：angle( or hole inclination)方位角：azimuth井眼环空：annulus第5 节石油钻井作业现场工作人员名称甲方：oil company(operator)钻井承包商：drilling contractor第三方（分包商）the third party(sub-contractor)钻井经理：drilling manager监督：supervisor钻井监督：DSV(drilling supervisor) or Companyman 地质监督：geologist泥浆工程师：mud engineer固井工程师：cementing engineer泥浆录井工：mud logger钻井队：drilling crew，drilling team钻井1 班：drilling shift one总经理：general manager总工程师：chief engineer项目经理：project manager(country manager)作业经理：operation manager财务经理：financial manger会计：accountant平台经理：rig manager带班队长：tool pusherHSE 监督：HSE officer司钻：driller副司钻：assistant driller井架工：derrick man钻工：roughneck（or floorman）场地工：roustabout泥浆工：mudman发动机工：motorman机械师：mechanic电工：electrician电焊工：welder司机：driver吊车司机：crane operator铲车司机：forklift operator营房经理：camp boss医生：doctor材料员：material man(storekeeper)炊事员：cook翻译：interpreter洗衣工：laundry man厨房服务生：waiter保安：watchman(or security)机械工程师：mechanic engineer第6 节石油作业现场常用工具扳手：wrench螺丝起子：screwdriver多角螺丝起子：Phlilips screwdriver （cross-headed screwdriver）撬杠：bar加长撬杠：cheater bar活动板手：monkey wrench，adjustable wrench钳子：pliers钩子：hook台钳：bench vice钢挫：file榔头：hammer锤击扳手：hammer wrench搬手：spanner内六角扳手：Allen key钢锯：hacksaw砂纸：sandpaper管钳：pipe tongs(pipe wrench)链钳：chain tong千斤顶：jack黄油枪：grease gun吊车：crane牵引绳：tag line电焊条：welding rod拖拉机：tractor推土机：bulldozer硬尺：ruler游标卡尺：Vernier slide油漆：paint铅油：dope油漆刷：paint brush铅油刷：dope brush绝缘胶布：electrical tape电线：wire插头：plug电插座：outlet(receptacle or switchboard)开关：switch螺栓：bolt螺帽：nut垫片：washer钉子：nail手电钻：hand drill钻头：bit工作台：workbench工具箱：toolbox胶水：glue胶棒：glue bar护丝：thread protector手轮：hand wheel脚轰油门：throttle联接法兰：coupling flange(or adaptor flange) 安全带：safety belt安全帽：helmet工作靴：safety boot工衣：coverall棉袄：coat防护眼镜：safety goggle手套：gloves口罩：mouth mask围裙：apron洗眼台：eye washing station灭火机：fire extinguisher消防栓：fire -hydrant水龙头：water tap消防斧：fire fighting axe铲子：shovel手砂轮：emery wheel左转：turn left右转：turn right手势：gesture信号：signal垃圾：waste garbage拖把：mop接头：sub配合接头：X-over ，cross-over提升短节：lifting sub卡瓦：slips放卡瓦：set slips母锥：box tap公锥：taper tap打捞矛：fishing spear安全接头：safety sub柔性短节：flexible joint井口盖子：wellhead cover防喷盒：mud boxBOP 吊装：BOP trolley( BOP hoist) 吊卡：elevator吊环：elevator links安全卡瓦：safety clamp(dog collar) 钻杆架：pipe rack水龙头提环：swivel bail材料房：warehouse绳卡：bullnose clamp(guy anchor) 绳套：sling吊带：soft sling(belt)卸扣：shackle吊装工具：lifting gear维护保养：maintenance内钳：make-up tong外钳：break-out tong液压大钳：power tong液压猫头：E-zy tong兜绳：mule line四通阀：four-way valve三通：Tee软管：hose球阀：ball valve闸板阀：gate valve单流阀：back valve灌注泵：supercharge pump第二章：石油工程常用设备及专业术语第1 节钻井设备部分井架：Derrick(or mast)起（放）井架：erect(lay down) Derrick 底座大梁：sill钢木基础：mat铅锤：plumb水平仪：level架，台：rack立根盒：setback area坡道：V door(or ramp)猫道：catwalk二层台：monkey-board圆井盖：cellar cover天车：crown block防碰天车：crown-o-matic天车梁：crown block beam天车台：water table游动滑车：traveling block钻井大绳：drilling line引绳：guide line穿大绳：string-in drilling line金属线，电线：wire，cable钢丝绳股：strand截断：cutoff滑车，滑轮，皮带轮：pulley(hoist)手拉葫芦：hand pulley吊耳：lifting eye顶驱：top drive大钩：hook大钩弹簧：hook spring大钩销子：hook pin大钩锁紧装置：hook locking device大钩悬挂高度：hook height水龙头：swivel鹅颈管：gooseneck冲管：wash pipe水龙头盘根：swivel packing钻井水龙带: rotary hose( kelly hose)立管：stand pipe立管管汇：stand pipe manifold高压管线：high pressure line由壬：union低压管线：low pressure line传感器：sensor放压管线：relief line转盘：Rotary Table转盘方瓦：master bushing方补心取出装置：bushing handling tool方补心：kelly drive bushing方孔：square opening小鼠洞：mouse hole大鼠洞：rat hole绞车：Drawworks挂合（摘开）绞车：engage(disengage) drawworks液压绞车：hydraulic winch气动绞车：air tugger(air hoist)滚筒：drum( reel)滚筒高速气离合器：high speed clutch滚筒低速气离合器：low speed clutch锚头：cathead液压猫头：E-zy tong上扣猫头：make up cathead卸扣猫头：make out cathead牙嵌离合器：jaw clutch涡磁刹车：eddy current brake(electromagnetic brake) 猫头轴：cathead shaft猫头绳：cathead line死绳：dead line死绳固定器：dead line anchor间隙：gap死绳固定器膜片：dead line diaphragm上扣：make up上扭矩：torque sth卸扣，卸开：break out上紧，固定：tighten（fasten）松开，松扣：loosen加载：load卸载：unload盘式刹车：disc brake刹车总成：brake assembly刹车轴：brake shaft刹车带：brake band刹车片：brake block液压油箱：hydraulic power unit液动试压泵：hydraulic test pump 液压大钳：hydraulic （power）tong 倒档齿轮：reverse gear动力扳手：power wrench吊钳钳头：hinged jaw钳牙：die大钳锁销：latch大钳悬臂：suspension bar平衡重：counterbalance weight吊钳钳臂：tong arm第2 节钻井泵类及相关设备泥浆泵：mud pump活塞：piston活塞杆：piston rod活塞皮碗：piston cup缸套：liner凡尔体：valve body凡尔座：valve seat凡尔箱：pump module阀弹簧：valve spring阀杆：valve lever阀面：valve face阀帽：valve bonnet空气包：pulsation damper充氮气：refill with nitrogen泥浆泵安全阀：pop-off valve卸压管线：release line排出阀：discharge valve吸入阀：suction valve上水滤子：screen油尺：oil-level dipstick灌注泵：supercharge pump冷却水泵：cooling pump潜水泵：submersible pump盘根盒：stuffing box叶轮：impeller单向阀：check valve（single-pass valve）安全阀：safety valve手动阀：manual valve液动阀：hydraulic valve拉杆：tie rod，tension bar压力表：pressure gauge冲数：strokes排量：flow rate80 冲(次)/分：eighty strokes per minute泥浆罐：mud tank倒泥浆：transfer mud循环罐：active tank储备罐：reserve tank起下钻罐：trip tank溢流检查：flow check沉砂罐：satteling tank锥形罐：sand trap震动筛：sahle shaker筛布：screen目数：mash除砂器: desander除泥器: desilter离心机：centrifuge泥浆分配槽：spider box缓冲罐buffer tank第3 节与泵操作有关的实用短语没有压力：No pressure压力过高：The pressure is too high返回太少：Mud return is too few水太少：Water is not adequate.抢修：Rush to repair请看记录：Please check the record没作记录：No record available加化学药品：add chemicals测定比重：measure mud weight(specific gravity) 测定失水：measure water loss泥饼：mud cake测定切力：measure gel strength停泵：stop pump请打手势：Please make a gesture转动一周：turn round a circle垫高一些：put something under it to raise 抓紧：firmly grasp抬高：lift it up拿稳：hold firm打一下：hit once往外拉：pull outward站稳：stand firm小端：small end大端：large end光滑：smooth粗糙：coarse，rough平面：flat弯曲：bending放松：loosen绷直：stretch tight，draw tight冷却：cooling润滑：lubricate过载：overload功率不足：power is not enough.第4 节钻台与底座钻台：drilling floor钻井班组记录：drilling tour record司钻监视器：driller's monitor司钻控制台：driller's console指重表：weight indicator底座：substructure井队活动房：trailer钻台上值班房：doghouse梯子：ladder第5 节井控操作与防喷器溢流: kick溢流征兆: kick sign气侵：gas cut井喷：blow-out1 次井控the primary well control2 次井控the secondary well control3 次井控the tertiary well control平衡balance超平衡over-balance欠平衡under balance漏失试验leak-off test破裂压力fracture pressure额定压力rated pressure工作压力working pressure防喷器组BOP stack安装（甩下）防喷器组：nipple up(nipple down) BOP stack 分流器diverter万能防喷器：annular preventer，bag preventer单闸板防喷器：single ram preventer双闸板防喷器：double ram preventer（防喷器）闸板：pipe ram变芯闸板防喷器variable bore ram全封式防喷器：blind ram剪切防喷器：shear ram内防喷器Inside BOP投入式单流阀DIBPV（Drop in blowout preventer valve）分流关线diverter line节流管汇choke manifold节流阀choke valve旁通阀standby valve调压阀: Pressure regulator手动节流阀manual choke远程节流阀remote choke井口四通drilling spool变径法兰：adapter flange液压控制阀HCR(hydraulic controller)远程控制系统：koomey unit蓄能器：accmulator压井管线：kill line入口：inlet出口：outlet简易除气器：poor-boy degasser真空除气器：vaccum degasser泥浆池液面纪录仪Pit volume recorder(totallizer)泥浆流动传感仪mud flow sensor泥浆增量Pit gains硫化氢侵入H2S influx加重材料Weighted material氮气Nitrogen乙炔：acetylene氧气：oxygen预冲氮气压力Pre-charge nitrogen pressure地脚螺栓连接Studded connection法兰连接Flange connection箍盘连接Hub connection演习：drill急救演习：first aid drill消防演习：fire drill防喷演习：kick drill泄压: bleed off pressure带刻度压力表: calibrated pressure gauge带刻度容（体）积表: calibrated volume gauge套管鞋: casing shoe上部井眼段top hole section快速钻进地层fast drilling formation压实地层：consolidated formation风化地层：weathered formation钻屑携带能力cuttings carrying capacity浅层气藏shallow gas地层破裂formation to break down压力梯度pressure gradient地层压力formation pressure井口压力wellhead pressure漏失压力leak-off pressure破裂压力fractured pressure井底压力BHP( bottom hole pressure)正常压力normal pressure异常压力abnormal pressure静液压力hydrostatic pressure动态压力dynamic pressure环空压力annular pressure关井钻杆压力SIDPP (shut in drill pipe pressure)关井套管压力SICP( shut in casing pressure)最大关井套管压力maximum allowable surface pressure, MAASP 最初循环压力ICP( Initial circulating pressure)循环结束压力FCP(Final circulating pressure)U 形管原理U-tube principle压井操作killing operation补救措施remedial actions关井后循环circulation under well closed in conditioncl 离子含量chloride contentDc 指数Dc exponent软关井soft shut in硬关井hard shut in第1 次循环first circulation第2 次循环second circulation压井泥浆比重kill mud weight抽吸swab激动surge含气地层gas bearing formation含气页岩gas bearing shale安全增量safety margin记录卡片trip sheet低循环泵速SCR(slow circulation rate)当量泥浆密度EQD(equivalent mud density)当量循环密度ECD(equivalent circulating density)司钻压井法driller’s method等待压井法wait & weight method体（容）积法volumetric method下推压井法bull-heading method不压井下钻：snub in第三章：钻井工程作业部分第1 节钻井事故井喷：blow out井涌：kick井漏：lost circulation坍塌，井壁坍塌：cave in(collapse)出砂：sand production砂桥：sand bridge台阶：ledge键槽：keyseat椭圆井眼：oval shaped hole卡钻：sticking填井：pack-hole封井：packed drilling井下落物：fish大幅度活动钻具试图解卡：work the string and try to free it活动钻具以避免卡钻：move(reciprocate ) the string to avoid being stuck. 打捞：fishing鱼头：top of fish打捞工作：fishing job侧钻：side-tracking侧钻井眼：sidetracking hole水泥窜槽：cement channeling固井失败：cement failure防砂：sand control缓慢开泵并仔细观察返浆情况：slowly start pumping and closely watch the return on the shale shaker 第2 节钻头牙轮钻头：rock bit刮刀钻头：drag bit金钢石钻头：diamond bit镶齿钻头：insert bit铣齿钻头：milled tooth bit喷射钻头：jet bit牙轮：cone钻头装卸器：bit breaker钻头直径：bit diameter钻头寿命：bit life钻头磨损：bit wear钻头型号：bit type水眼尺寸：nozzle size水眼效率：nozzle efficiency钻头接头：bit sub第3 节钻具方钻杆：kelly方钻杆旋扣器：kelly spinner方钻杆旋塞：kelly cock钻具：drilling string钻杆：drill pipe油管：tube钻具组合：drilling assembly扶正器：stabilizer扩眼器：reamer（hole opener）钻铤：drill collar无磁钻铤：NMDC(non-magnetic drill collar) 加重钻杆：HWDP(heavy weight drill pipe) 近钻头扶正器：near-bit stabilizer震击器：jar减震器：shock absorber螺旋钻铤：spiral drill collar键槽破坏器：key seat reamer安全接头：safety joint钻杆刮泥器：drill pipe wiper泥浆动力钻具：mud motor钻柱：drill string涡轮：turbine涡轮钻具：turbo-drill stem立根：stand加厚：upset内加厚：IU(internal upset)外加厚：EU(external upset)内外加厚：internal-external upset丝扣：thread打捞颈：fishing neck母扣：box公扣：pin左旋螺纹：left-hand thread右旋螺纹：right-hand thread正规接头：regular joint贯眼接头：full hole joint内平接头：internal flush joint护丝：thread protector快速护丝：easy protector打捞工具：fishing tool打捞作业：fishing operation打捞篮：junk basket卡瓦打捞筒：overshot打捞杯：junk sub牙轮打捞器：cone fisher套管打捞矛：casing spear打捞矛：fishing spear打捞公锥：male tap(fishing nipple)打捞母锥：female tap(fishing socket)倒扣工具：reversing tool(backing-up tool) 铣鞋：milling shoe铣具：milling tool平底铣鞋：flat bottom mill磁力打捞工具：magnetic fishing tool打捞钩：fish hook气动工具：pneumatic tool减摩短节：friction reduction sub下套管漂浮接箍：casing floating coupling 轴向加压器：hydraulic axial thruster第4 节钻井工程地面作业实用词汇与短语方入：kelly-in方余：kelly-up开钻：spud in作业指令：instruction钻井设计：drilling program井身结构：well schematic岩性：lithology迟到时间：lag time(bottom up)换钻头：change bit甩钻具：laydown drill pipe发生故障：break down安装（拆卸）：rig up(rig down)接头：sub adapter机械手：mechanical arm铁钻工：iron roughneck有故障：It fucked up( something is wrong with it)已修好：it has been fixed马上去：Go there at once请下去：Please go down请上来：Please come up躲开，危险：keep away，danger.请翻译来：Ask interpretor come here，冲洗：wash down井口：well-head一根钻杆（单根）：single三根钻杆组合（立根）：thribble吊蓝：cage(basket)换班：shift change第5 节钻井工程井口作业实用词汇与短语喇叭口：bell nipple出水管：mud return line(flow line)试压杯：cup tester小心滑倒：wet floor, be careful不要往井眼内掉东西：never fall down anything inside hole 我来做：Let me do it带把板手来：Bring a spanner，please带点密封剂：Bring a little sealant(Teflon)，please很快就好了：lt will be finshed right away抬一下：Let's lift it把绳子给我：Give me the rope，please不漏：no leakage电焊：welding气焊：gas welding气割：gas cut栏杆：handrail，gangway rail，railing蒸汽：vapour压缩空气：pressurized (compressed) air注意安全：pay attention to safety别动：Don't move，Don't touch.对准：point out exactly.校正：align裸眼：open hole第四章：钻井液及相关设备第1节钻井液名称泥浆：mud钻井液：drilling fluid完井液：completion fluid修井液：work-over fluid压井液：killing fluid射孔液：perforating fluid隔离液：spacer fluid泥浆处理：mud treatment泥浆处理设备：mud treating equipment饱和盐水泥浆：saturated salt-water mud油基泥浆：oil-base mud高粘度泥浆：heavy viscous mud重泥浆：weighted mud重泥浆压钻杆：slug drill pipe起钻倒返泥浆：we have wet pipeduring POOH 重晶石：barite纯碱：soda ash高岭土粉：koaline powder云母片：mica sheet增粘剂：viscosifier稀释剂：diluent (thinner)稳定剂：stabilizer (stabilizing agent)烧碱：caustic soda稀释dilution, thinning水泥凝固cement setting第2 节钻井液设备离心泵：centrifugal pump振动筛跑泥浆：mud overflow shale shaker筛出：shake out混合泵：mixing pump混合漏斗：mixing hopper搅拌器：mud agitator泥浆抢：mud gun岩屑：cuttings沉淀：settle沉积物：deposit吸入：suction吸入罐：suction pit泥浆天平：mud balance游码：slide weight支点：fulcrum刀口：edge调整，校正：adjust粘度计：viscometer第3 节钻井液处理剂包，袋：sack粘土：clay膨润土，般土：bentonite钠：sodium钙：calcium氯：chloride氯化钙：calcium chloride石棉：asbestos分散：dispersal表面活性剂：surface-active material铁络盐：lignite单宁：tannin羧甲基纤维素：carboxymethyl celluose CMC 木纤维：xylogen石灰：lime二氧化钙：calcium oxide粉末：powder薄片：flake溶解：dissolve延迟，妨碍：retard处理剂，添加剂：additives缓凝剂：retarder支撑剂：proppant乳化剂：emulsifier润湿剂：wetting agent稳定剂：stabilizing agent除钙剂：calcium remover降失水剂：filtration-reducing agentPH 值控制剂：PH control additive润滑剂：lubricant消泡剂：defoamer agent破乳剂：emulsion breaker洗涤剂：detergent防膨胀剂：anti-swelling agent粘土稳定剂：clay stable agent稀释剂：thinner封堵剂：plugging agent抑制剂：inhibition agent暂堵剂：temporary plugging agent解堵剂：plugging removal堵漏剂：LCM (lost circulation material)水敏地层：water-sensitive formation分散：dispersal水泥浆：cement slurry流变性：rheological characteristics稳定性：stability稠化时间：thickening-time低密度水泥浆：low-density slurry油气层保护：reservoir protection高渗透性：high-permeability砾石：gravity悬浮：suspension固化：solidification.防膨胀：anti-swelling高凝高粘度：high condensation and viscosity 无毒的：non-poisonous无荧光：non-fluorescence钻井液性能参数Specificaitons of Drilling Fluid 含水：water content密度：density厚度：thickness粘度：viscosity塑性粘度：plastic viscosity含砂量：sand content屈服：yield屈服点：yield point屈服强度：yield strength剪切速率：shear rate剪切强度：shear strength剪切应力：shear stress稀释：dilute适用温度：safe temperature初始切力：initial gel strength终切力：ten-min gel strength触变性：thixotropy剪切稀释：shear thining液体浓度:concentration泥浆柱：mud column层流：laminar flow涡流：turbulent flow气泡：bubble第五章：钻井相关作业第1节取芯部分岩心：core取心钻头：core bit取心筒：core barrel内岩心筒：inner barrel外岩心筒：outer barrel岩心爪：core catcher取心工具：corehandling tools取心收获率：core recovery rate取样器：sample blob取样盒：sample box样品筒：sample chamber取样工：sample catcher取样间隔：sample interval井壁取心：side-wall coring井壁取心枪：side-wall coring gun取芯失败：coring failure第2 节固井部分固井：cementing完井：well completion水泥：cement井口：wellhead井口压力：well head pressure井口回压：back pressure on the well head套压：casing pressure导管：conductor表层套管：surface casing技术套管：protective casing(intermediatecasing) 油层套管：production casing尾管：liner尾管悬挂器：liner hanger通径轨：rabbit封隔器：packer联顶节：landing joint套管柱casing string套管下部结构(含套管鞋、浮箍)：casing track(including casing shoe, float collar) 套管扶正器：centralizer止退环：stop collar口袋：pocket( rat hole)环空注水泥作业：top cement job碰压：bump plug隔离液：spacer分级箍：stage collar水泥粘结强度strength of cement bond套管钳：casing tongs套管接箍：casing coupling套管头：casing head散装水泥：bulk-cement水泥浆：cement slurry插管注水泥：stab in cementing插入密封接头：stab in adapter分级注水泥：stage cementing先行水泥浆：lead cement slurry末端水泥浆：tail cement slurry促凝剂：accelerator替浆：displace with mud水泥面：top of cement固井管线：chicksan line(cementing line)灰罐：silo(bulk tank)候凝：WOC(wait-on-cement)挤水泥：squeeze cement水泥塞：plug第3 节固井水泥浆名称和参数超细水泥浆：ultrafine slurry普通水泥浆：normal slurry纤维水泥浆：fiber-reinforced cement slurry膨胀水泥浆：expanding cement slurry低密度水泥浆：low-density slurry水泥体积收缩：cement volume contraction水泥浆水化期间：cement slurry hydrating period 水泥胶结质量：cement sheath bonding quantity 失水率：the rate of water loss析水：liberate water稠化时间：thickening time凝固强度：cementation strength渗透性：permeability，膨胀率：expansion rate压缩强度：compression strength流动性：mobility第4 节测井部分电测：wireline logging测井解释：logging interpretation随钻测井：LWD(logging while drilling)测井电缆：logging cable测井工具：logging tool自然电位测井：spontaneous potential log感应电测井：induction electrical survey双感应测井：dual induction-laerolog中感应测井：medium induction log数字记录：digital record照相记录：photographic recording放射性测井：radioactivity log声波技术：acoustic wave technology仪器耐温：the temperature resistance of the instrument仪器耐压：pressure resistance of instrument油气比：GOR (gas oil ratio)第六章：井下作业常用短语修井：work-over修井工具：work-over tool井下操作：down-hole operations.产层污染：pollution of pay zone增产措施：stimulations压裂和酸化：fracturing or acidizing酸化处理：acid treatment人工压裂：artificial fracturing重复压裂过程：repetition presses for fracturing，压裂车：fracturing truck sets压裂后反映：post-fracture response固体和液体添加泵：solid and liquid additive pump泵交联：pumping cross link交联剂：cross-linking agent排量：discharging三维压裂：three-dimension fracturing对压裂参数的监控、分析和解释：real time monitoring，analyzing and interpreting for fracturing operation parameters压裂操作：fracturing operation压裂规模：fracturing scale化学吞吐：chemical disposal乳化降粘：emulsification declining viscosity增注：augmented injection.注水：water-injection裸眼砾石填充完井：bore hole gravel packer completion.开窗铣锥：open-window mill prick，开窗斜向器：open-window inclined implement碳酸盐岩：carbonate reservoir第七章：海上钻井作业¨海上钻井：offshore drilling陆地钻井：on-land drilling海滩：sea beach浅海：shallow sea海底管线：sea-bottom pipe海底电缆铺设：setting cable under sea-bottom平台安装：platform installation钻井平台：drilling platform顺风：tail wind逆风：against the wind摄氏零下…度：belo w…degree centigrade启锚：weigh anchor抛锚：drop anchor拖航：drag对讲机：intercom，walkie-talkie上吊茏：Please get on the liftbasket救生衣：life jacket晕船：sea sick控制速度：Control the speed货已送抵：The goods has arrived货物验收：Please check and accept the goods在不远处：Not far from here不方便：lt's not convenient有危险：lt's dangerous防污染：prevent pollution没情况：Nothing happened.第八章：定向井部分定向井：directional well造斜点：ＫＯＰ（kick off point）最大井斜角：maximum hole inclination增斜段：building up section稳斜段：holding section降斜段：drop off section井眼尺寸：hole size长、中、段半径：long，medium and short radius 裸井段：the open hole section水平段：horizontal section固井段：cementing section井斜角测量点：angle point水平位移：horizontal departure(displacement)井眼轨迹：wellbore trajectory优化控制：optimum control筛管：screen pipe长封固段固井：long intervals cementing丛式井：cluster well斜向器：whipstock第九章：石油现场机械传动与机械设备第1 节：动力与传动柴油机：diesel发电机：generator直流（交流）电动机：DC（AC）motor交流电：A.C （alternating current）直流电：D.C （direct current）变压器：transformer传动轴：driving shaft从动轴：driven shaft空调机：air conditioner空气压缩机：air compressor应急发电机组：emergency generator消防水泵：fire pump配电间：distrubution room电动潜水泵：ESP(electrical submersible pump) 锅炉：boiler蒸汽：vapour气压不足：The airpressure is poor操作有问题：Operation is not good电压正常：Voltage is all right绝缘不好：The insulation is bad触电：electric shock温度太高：The tempreture is too high接地：ground短路：short circuit按红色钮：Please push the red button打开：open，turn on，switch on关闭：close，turn off，switch off风扇：fan爬上去：climd up跳下来：jump down接住：catch it拿稳：hold tight平方米：square meter立方米：cubic meter加工：process三项交流电：three-phase AC气罐：air tank偶合器，联轴节：coupling链轮：sprocket链条：chain皮带：belt链条驱动：chain drive皮带驱动：belt drive第2 节机械加工与设备对准，使…成一线：align周围的，环境的：ambient模糊，含糊，不明确：ambiguity退火的：annealed淬火：quench回火：temper阳极：anode阴极：cathode含水的，水的：aqueous装配：assembly增大，增加，增益：augment侧向间隙：back-lash电木，（绝缘）胶木：Bakelite批量生产：bulk production轴承：bearing锥齿轮，伞齿轮：bevel gear（刮刀，刃，叶片：blade坯料：blank吹风，爆炸，喷砂机：blast滑轮组：block and tackle浮子，摆锤：bob镗床，镗孔刀具：borer内孔加工，镗孔：boring瓶颈，薄弱环节：bottleneck平衡点，盈亏临界点：breakeven point 型坯：briquette拉床，铰孔机：broacher拉削，扩孔：broaching大齿轮：bull gear碰撞，曲折，拐点：bump缓冲器，减震器：bumper擦亮，光亮：burnish去毛刺：burring凸轮，偏心轮：cam凸轮轴：camshaft铸造：cast触媒，催化剂：catalyst空化作用：cavitation内腔，空穴，（铸造）型腔：cavity陶瓷的，陶器的，陶瓷制品：ceramic 铁屑，金属屑：chip凿子，扁铲：chisel钳：clamp障碍（物），阻塞（物）：clog离合器：clutch罗盘，指南针：compass凸型的：convex凹型的：concave外形，轮廓；结构，构造：configuration锥形的，锥状的，锥体：conical传送装置，运输机，传送带：conveyor波纹；使成波状：corrugation曲柄，曲拐：crank曲轴：crankshaft蠕动，蠕变：creep圆筒，圆柱体；液缸:cylinder仪表盘，控制板：dashboard静载：dead load碎片：debris模具，钢型，冲模：die模锻：die forge压铸的，模铸的：die-cast不导电的，电解质（的）：dielectric差动齿轮，差速齿轮：differential gear扩散，弥漫：diffusion修饰，打磨，使表面光洁：dress钻床：drill press染色，着色；染料：dye电解质：electrolyte椭圆，椭圆体：ellipse金刚砂：emery侵蚀，冲蚀：erosion蚀刻：etch排出，排气；废气：exhaust消音器：muffler爆炸物，炸药；爆炸（性）的：explosive挤压（成形）；挤出，压出：extrude平面加工：facing测隙规：feeler gauge膜：film精加工：finish柔性的，能变形的，灵活的，适应性强的：flexible 软盘：floppy disc硬盘：hard disk车床：lathe流程图：flow chart起伏，波动：fluctuation开槽，切槽：fluting飞轮：flywheel锻造：forge支点，支轴：fulcrum（龙门）起重机：gantry几何学：geometry花岗岩，花岗石：granite石墨：graphite润滑脂：grease磨碎，研磨，磨削加工：grinding槽，沟，企口：groove陀螺仪，回转仪：gyroscope主轴箱：headstock螺旋形的，螺线：helical螺旋齿轮，斜齿轮：helical gear六角形（的）：hex万向接头，万向联轴节：hooke (cardan) joint,flexible joint 削弱，损害：impair冲击，脉冲：impulse测斜仪：inclinometer（刻度盘上的）指针，（铣床）分度头：index铸模，锭：ingot间歇的，断续的：intermittent内在的，固有的：intrinsic离子：ion夹具，夹紧装置，钻模：jig铰链，关节，肘关节，转向节：knuckle搭接，重叠；研磨，精研，抛光：lapping心轴，紧轴，芯棒：mandrel铣削加工：milling铣刀：milling cutter铣床：milling machine混合，混合物，混合气：mixtrue小孔，注油孔，喷嘴：orifice坑，池，孔：pit枢轴，旋转中心，支点：pivot气动的，气体的，风力的：pneumatic泊松比：Poisson’s ratio抛光：polish细孔，微孔，空隙：pore多孔性，空隙度，气孔，砂眼：porosity。
石油专业英语常用
石油专业英语常用The Standardization Office was revised on the afternoon of December 13, 2020石油专业英语（常用）油井（oilwell）指任何钻透地球表面（Earth'ssurface）的钻孔（boring），目的是发现（find）或生产（produce）石油（petroleum/oil/hydrocarbons）。
专门生产天然气的叫气井（gaswell）。
油井一般经历五个阶段：计划（planning）、钻井（drilling）、完井（completion）、生产（production）与报废（abandonment）。
首先用钻机（drillingrig）通过钻具（drillstring）上的钻头（drillbit）在地上钻出毫米的孔（hole），然后在钻孔（borehole）中下钢制油管（steeltubing）与套管（casing）。
套管与钻孔之间还可能需要用水泥（cement）来固定。
套管为井孔（wellbore）提供结构上的整体性（structuralintegrity），同时隔离（isolate）危险的高压区（highpressurezone）。
随着井深加大，钻头和套管尺寸会变小。
现在的油井通常都有2-5个逐渐变小的井口尺寸。
钻头通过与之连接的钻铤（drillcollar）来钻进岩层。
钻井液（drillingfluid/mud）通过钻杆（drillpipe）内部泵入钻头，作用包括冷却（cooling）钻头、提升钻屑（drillcuttings）、避免井壁（wellborewall）不稳定以及避免岩层液体由于压力进入井眼。
使用过的钻井液用振动筛（shaker）去掉钻屑后返回泥浆池（pit）循环利用。
通过在地面的顶部驱动装置（topdrive/kellydrive）增加额外的10米长的钻杆（joints）来增加钻井深度。
石油工程专业英语教学内容
第一章石油钻井工程英语基础第1节石油钻井工程基础词汇1.钻探，钻井：drill————拓展记忆钻井：drilling定向斜井directional drilling 欠平衡钻井under-balance 海上钻井off-shore陆地钻井on-land drilling 钻头：drill bit 刮刀钻头：drag bit 牙轮钻头rock bit金刚石钻头diamond bit 喷射钻头jet bit 钻铤drill collar 衣领collar钻杆：drill pipe 钻井队drilling crew 钻机drill rig 钻井泥浆drilling mud钻井液drilling fluid2.油，石油：oil————拓展记忆原有crude oil 石油petroleum 中国石油Petro-China 采油oil production采油设备oil production equipment 采油平台oil production platform 油泵oil pump3.地质：geology————拓展记忆地质专业人员geologist 物理physics地球物理勘探geo-physical probe，geo-physical exploration测井logging 测井作业logging operations 测井记录logging record4.油井：well————拓展记忆井眼hole 油井oil well 试井，油井测试well test 井下down-hole井下作业down-hole operation第2节石油钻井方法基础词汇原油crude oil 天然气natural gas 煤层气coal-bed gas 一体化设计integral design钻井drilling 钻井原理the principles of drilling顿钻钻井percussion drilling，cable-tool drilling 旋转钻井rotary drilling液体冲击fluid percussion 大位移big deviation侧钻井sidetracking drilling technology lateraldrilling水平井horizontal well 探井wildcat，wildcat drilling 深井deep well 浅井shallow well老井maturing well 欠平衡钻井under-balanced drilling 丛式钻井cluster drilling technology 煤层气井coal-bed gas well 生产井production wells 报废井abandon wells停产井non-production wells 绕障井、三维井three-dimensional wells常温井normal temperature well 注采井injection and production well 稠油井heavy oil well热洗井hot washing pipe 井况well condition石油钻井技术基础词汇技术规范，技术指标，技术性能：specification拉伸tension 拉伸强度tension strength 应力stress 压力pressure 应力点stress point压力等级pressure grade 压力降pressure drop 压力梯度pressure gradient回压back pressure 大气压atmosphere 压差differential pressure静液柱压力static fluid column pressure 特征characteristic，feature定性讨论qualitative argiment 定量使用quantitative use液体liquid 固体solid 气体gas，air 正的positive 负的negative虚线dashed line，broken line 实线full line 递减率decline rate 正比于be proportional to 水平的horizontal 垂直的vertical 油层静压the formation static pressure石油钻井参数基础词汇负荷load 扭矩torque 扭转twist 摩擦friction钻压WOB, weight on bit,weight, drilling weight钻速rate of penetration, drilling rate, the rate of drilling, average ROP 钻井周期drilling period 钻速rotary speed 地层压力预测formation pressure prediction technology地层快速预测the formation fast prediction 埋藏深度bury depth产油层，产油带，pay zone，productive formation温度梯度temperature gradient 地层压力formation pressure 坍塌压力collapse pressure破裂压力fracture pressure 平衡压力equilibrium pressure钻具（柱）压力drilling string pressure 钻头振动vibration of bit 钻井成本drilling costs井眼尺寸hole size，well size 参数计算parameters calculation几何参数geometric parameters 参数分析parameter analysis 动态参数dynamic data静态监测static data 注水参数parameter of injection 参数、变量variables 井距well space 垂直深度vertical depth 水平位移horizontal deviation 总深度total depth水平位移horizontal displacement 最大井斜角maximum hole inclination井眼环空annulus space 压力调节器pressure regulator 恢复（增加）压力the build-up pressure 初始开采primary recovery 含水地层water bearing formation 套管漏失casing leak摩擦损失friction losses 气聚阀gas-lift valve 石蜡族paraffin series含气液柱gas-laden column 增产措施stimulation treatment 流动能力flowing capacity生产速率production rate 水驱water drive 气驱gas drive 网状系统grid system水侵water influx 五点法five-spot pattern 油井产量well-productivity 径向流radial system 富气enriched gas 贫气lean gas 气顶gas cap 气驱gas drive（or gas flooding）水驱water drive (or water flooding) 地层伤害formation damage 波及系数sweep efficiency 泄油半径drainage radius 基岩处理matrix treatment 单级脱气single stage separation泄油面积drainage area 表面张力surface tension 束缚力connate water（or interstitial water）石油钻井作业现场工作人员名称1 钻井队drilling crew 队、组crew、team2 技术员technician 钻井技术员drilling technician 泥浆技术员mud technician3 监督supervisor 钻井监督drilling supervisor 副监督assisstant supervisor地质监督geology supervisor4 工程师engineer 泥浆工程师mud engineer 泥浆工mudman机械工程师mechanic engineer 引擎、发动机engine 工程engineering钻井工程drilling engineering 采油工程production engineering石油工程petroleum engineering 试油工程oil test engineering拓展记忆---------------------------工作项目project 希望工程the hope project 三峡工程the Three-Gorge Project项目经理project manager 工程管理project management 钻工：roughneck、floorman司钻driller 副司钻assistant driller 钻井队长drilling foreman 钻井领班tool pusher井架工derrick man 发动机工，机工motorman 钻台工floorman机械师technicians，mechanic 电焊工welder 电工electrician 医生doctor材料员material man，staff man 炊事员cook 翻译interpreter, tansalator洗衣工laundry man石油作业现场常用工具石油作业现场普通工具扳手wrench 螺丝起子screwdriver 多角螺丝起子Phlilips screwdriver活动扳手monkey wrench，adjustable 钳子pliers 手斧hatchet 钩子hook 台钳bench vice 榔头hammer 木锤mallet 搬手spanner 锯子saw 电动手锯jigsaw 电锯power saw钢锯hacksaw 硬尺rule 软尺tape measure 砂纸sandpaper 油漆paint 油漆刷paintbrush 绝缘胶布electrical tape 电线wire 插头plug 电插座outlet 开关switch 螺栓bolt螺帽nut 钉子nail 电钻electric drill 钻头bit 工作台workbench 工具箱toolbox胶水glue 交棒glue bar 管钳pipe tongs，pipe spanner，wrench链钳chain tongs，chain spanner，chain wrench护丝thread protector，screw protector手轮hand wheel 阀门搬手valve wrench，valve spanner 链接法兰coupling flange安全带safety belt 安全帽safety cap 工作靴working boots 千斤顶jack 吊车crane拖拉机tractor 推土机dozer 刮刀scraper1、石油作业现场专业工具接头sub 配合接头X-over，cross-over 提升短接lifting sub，lifting nipple elevator卡瓦slip 母锥box bell 公锥taper tap 短节joint 柔性短节flex joint 井口wellhead螺旋钻铤spiral collar 方钻杆kelly 钻杆架pipe rack 材料房warehouse 绳卡guy anchor 润滑器lubricator 维护保养maintenance 内钳lead tong 外钳back-up tong液压大钳hydraulic tong 兜绳mule line 四通阀four-way valve 软管hose球阀ball valve, globe valve 闸板阀ram valve, gate valve 增压泵booster pump换配件fittings change 灌注泵charge pump第二章石油工程常用设备及专业术语第1节钻井设备部分1 井架derrick 塔形井架derrick A形井架cantilever mast，mast-A 桅杆mast底座大梁sill 架，台rack 架工操作台monkey-board2 游动系统travelling systemn 天车crown block 天车梁crown block beam游动滑车travelling block 钻井大绳drilling line, wire line 金属线, 电线wire，line钢丝绳，测井电缆wire line 金属线，电线wire，line 钢丝绳股strand 截断cutoff滑车，滑轮，皮带轮pulley 吊耳eye plate3 大钩与水龙头hook and swivel 顶驱top drive 大钩hook 大钩弹簧hook spring大钩销子hook pin 大钩环hook ring 大钩锁紧装置hook locking device大钩悬挂高度hook height 水龙头swivel 鹅颈管gooseneck 冲管wash pipe水龙头盘根swivel packing 钻井水龙带drilling hose，rotary hose，kelly hose 立管stand pipe 高压管线high pressure line 低压管线low pressure line 放压管线relief line储气筒gas holder，air holder4 转盘rotary table 转盘方瓦master bushing 方补心kelly drive bushing方孔square openning 小鼠洞mouse hole 大鼠洞rat hole （井架大门处）坡板ramp5 绞车drawworks，hoist 液压绞车hydraulically-powered winch 气动绞车air operated hoist 绞车hoist，windlass，drawworks 滚筒线轴卷轴reel pool drum滚筒高速气离合器drum high air clutch 滚筒低速气离合器drum low high clutch猫头cathead 液压猫头hydraulic cathead 上扣猫头make up cathead卸扣猫头make out cathead 牙嵌离合器jaw clutch 应急牙嵌离合器emergency jaw clutch涡磁刹车eddy current brake 猫头轴cathead shaft 猫头绳cathead line猫头绳爪cat line grip 死绳dead line 死绳固定器deadline anchor死绳固定器膜片dead line diaphragm 上扣spin up，screw on 卸扣，卸开break out, screw off 上紧，固定tighten 松开，松扣loosen 加载load 卸载unload 拧紧screw 拧松unscrew 刹者brake 刹车总成brake assembly 刹车轴brake axle，brake shaft 刹车带brake band刹车片brake band lining 刹车杆brake bar 闸瓦brake block 刹把break crank，brake bar刹车鼓brake drum 离合器clutch 液压油箱hydraulic reservoir液动试压泵hydraulic test pump 液压大钳hydraulic tong 倒档齿轮reverse gear第2节钻井泵类及相关设备泥浆泵mud pump，drilling pump，slush pump 活塞piston 活塞杆piston rod活塞皮瓦piston cup 缸套liner，pumpliner 凡尔体valve body 凡尔座valve cup阀弹簧valve spring 阀杆valve lever 阀面valve face 阀帽valve bonnet泥浆泵安全阀mud relief valve 排出阀discharge valve 吸入阀suction valve潜水泵submersible pump 阀门valve 阀盖valve cap 阀座valve seat 回压阀回压阀back pressure valve 单向阀check valve single-pass valve 安全阀safety valve手动阀manual valve 液动阀hydraulic valve 冷缸cold cylinder 拉杆tie rod，tension bear 上水头intake，suction end 排出口discharge spout 高压管high pressure压力表pressure gauge 冲数strokes 排量displacement，discharge capacity，flow rate第3节井下泵类及相关设备泵筒pump barrel 柱塞plunger 关闭shut down 尾管tail pipe 抽油杆sucker rod长冲程long stroke 低泵速small pumping speed 泵充满度the fullness efficient of the pump 抽油杆sucker rod 排气方法gas bleeding method 泵效pump efficiency三维空间three dimensional space 有效生举efficient lift for the deviated抽油杆扶正工具sucker rod centralization tools 严重的管杆偏磨serious string partial wear游动阀the travelling valve 固定阀the standing valve 部分磨损、偏磨partial wear无杆泵rodless pump 小泵深抽small pump deep pumping technology挂泵深度pump setting depth 尾管长度length of liner 管柱结构the structure of pipe string防脱器dropout-prevent device 井斜角hole angle 电热杆borehole electric heating rod稠油开采heavy oil production 空心杆热载体hollow sucker rod heat carrier变扣器方补芯bushing 终端器terminal assembly 空心抽油杆hollow sucker rod整体电缆传感器continuous cable，sensor 空心光杆hollow polish rod 悬挂器hanger防喷盒stuffing box第4节采油设备采油树Christmas tree 抽油机pumping unit 往复运动reciprocating motion泵杆pumping rod 机械传动mechanical transmission 载荷能力peak polish rod load系统效率system efficiency 冲程stroke length 冲次frequency of stroke无级可调smooth regulation 沉降式抽油泵the sinking sand pump 泵下沉砂sinking砂颗粒sand particles 胶质沥青gum asphalt含蜡量paraffin content 凝固点solidification point 热流hot fluid 参水mingle water第5节与泵操作有关的使用短语没有压力no pressure 压力过高the pressure is too high 返回太少mud return is few水太少water is little 抢修rush to repair 请看记录please read the record没作记录no record 加化学小品put in chemicals 加高岭土粉put in koaline powder加云母片put in mica sheet 加增粘剂put in viscosifier 加稀释剂put in diluent（thinner）加稳定剂put in stabilizer（stabilizing agent）加烧碱put in caustic soda测定比重measure gravity，gravity test 测定失水test filtration 测定切力measure force开关switch 停泵stop the pump 请打手势please make a gesture转动一周turn round a circle 垫高一些put something under it to raise 抓紧firmly grasp抬高lift it up 拿稳hold firm 打一下strike once 往下拉pull out站稳stand firm take a firm hand 小端small end 大端large end 光滑smooth粗糙rough,coarse 平面plane，flat 弯曲winding，bending 放松loosen绷直stretch tight，draw tight 撬棍pinch bar，pry bar 充氨气nitrogen aeration 气包snubber 冷却cooling 润滑lubricate 过载overload 功率不足inadequate power，power is not enough第6节钻台与底座钻台drilling floor，derrick floor，rig floor 钻井记录drilling record司钻监视器driller’s monitor 司钻控制台driller’s console 指重表weight indicator转盘rotary table 卡瓦slip 吊卡latch elevator 底座substructure 井队活动房bunkhouse 钻台上值班房doghouse 立根盒setback （place）立根盒容量setback capacity井控设备well-control device第7节防喷器万能防喷器versatile blowout preventerBag type BOP单闸板防喷器single ram preventer 双闸板防喷器double ram preventer 闸板pipe ram全封闭式防喷器blind ram 蓄能器energy accumulator 压井管线kill line 入口inlet出口outlet 演习drill 消防演习fire drill 防喷演习BOP drill防腐涂料油管anti-corrosion coating material tubing 多功能管柱multi-function string第三章钻井工程作业部分第1节钻井事故泄漏leak 漏失fluid loss 出砂sand production 井喷blow out 井涌kick，flow off井漏lost of circulation，circulation lost坍塌，井壁坍塌caving，cave in，collapse出砂sand production，sand flow 桥塞bridge plug 砂桥sand bridge 井堵well clogging卡钻sticking 卡钻杆sticking the pipe 卡钻具sticking the drill stem 打捞fishing打捞工作fishing job 侧钻side-tracking 侧钻井眼sidetracking hole水泥窜槽cement channeling 固井失败cement failure 防砂sand control，sand-proof第2节钻头牙轮钻头rock bit，tooth-wheel bit 刮刀钻头drag bit 金刚石钻头diomand bit镶齿钻头tungsten carbide bit，insert bit 喷射钻头jet bit 铣齿钻头milled bit 牙轮cone钻头装卸器bit breaker 钻头直径bit diameter 钻头寿命bit life 钻头规格bit gauge钻头磨损bit wear 钻头型号bit type 水眼尺寸nozzle size 水眼效率nozzle efficiency钻头接头bit sub第3节钻具方钻杆kelly 方钻杆旋转短节kelly spinner 方钻杆考克（旋塞）kelly cock 接头sub钻头接头bit sub 钻具drill stem，drilling string 钻杆drill pipe 管子tube，pipe钻具组合drilling assembly 扶正器stabilizer，centering guide 翼状扶正器wing stabilizer扩眼器reamer drill collar 无磁钻铤drill collar 加重钻杆heavy weight drill pipe近钻头扶正器near-bit stabilizer 绕性接头flexible joint 震击器jar 减震器shock absorber 螺旋钻铤spiral drill collar 键槽破坏器key seat reamer 安全接头safety joint钻杆刮泥器drill pipe wiper 配合接头crossover sub 减震器shock sub井下钻具组合BHA-bottom hole assembly泥浆动力钻具mud motor 管线tubeline 钻柱drill string 涡轮tubine涡轮钻具turbo-drill stem 斜度taper，slope 塔式钻具tapered drill stem 接头 a joint，sub 管接头a joint of pipe 立根stand，a stand，thribble 加厚upset 内加厚internal upset外加厚external upset 内外加厚internal-external upset 丝扣thread 母扣box 公扣pin左旋螺纹left-hand thread 右旋螺纹right-hand thread 正规接头regular joint贯眼接头full hole joint 内平接头internal flush joint 护丝thread protector丝扣油thread dope，thread oil 打捞篮junk basket 打捞工具fishing tool打捞管柱fishing string 打捞公锥fishing nipple 打捞颈fishing neck 打捞头fishing head 打捞作业fishing operation 打捞母锥fishing socket 牙轮打捞器cone fisher倒扣工具reversing tool 卡瓦打捞筒slip socket 铣鞋milling shoe 铣具milling tool平底铣鞋flat bottom mill 磁力打捞工具magnetic fishing tool 套管打捞矛casing spear打捞矛fishing spear 打捞钩fish hook 套管打捞筒casing bowl 动力扳手power wrench动力大钳power tong 大钳活动牙块hinged jaw 大钳锁销latch 大钳悬臂suspension unit 气动工具pneumatic tool 打捞震击器fishing jars 打捞缓冲器fishing bumper sub打捞环die collar 打捞筒overshot 打捞短节junk sub 卡瓦slips 刮井器scatcher刮眼器扩井器wiper 油位检查丝堵oil lever check plug 油位oil lever油尺oil-lever dipstick 加油孔lubrication hole 盘根盒stuffing box 井筒工具well bore tool 配套工具matching tools 滚轮扶正器idler wheel centralizer 减磨短节friction reduction sub 轴线加压hydraulic thruster 扶正器centralizer 防脱器、装置anti-slip device减磨扭矩接箍torque-reduction sub 减扭接头torque reduction sub轴向水力加压工具hydraulic thruster 下套管漂浮接箍casing floating coupling轴向加压器hydraulic thruster第4节钻井工程地面作业实用词汇与短语方入kelly-in 方余kelly-up 开钻spud in，starting drilling 作业指令working instruction起钻POOH=pull out of the hole 下钻run in the hole 起下钻make a trip 短起下钻short trip 通井wiper trip 起下循环一周round a trip 循环时间round time，circulating time换钻头change bit 甩钻具laydown 填井pack-hole封井packed drilling发生故障break down 接单根connection 放卡瓦set slip，setting slip，起卡瓦pull slip扩眼openning 划眼reaming 二层台double monkey board，runround 顶部驱动器top drive 吊环bail 吊卡elevator 安全卡瓦safety slips 接头sub adapter 短节sub substitute井下震击器downhole（bumper）jar，down well shaker 打捞工具fishing tool三片卡瓦three slips，three pieces 补芯bushing 方补芯kelly drive bushings转盘补芯（大方瓦）rotary drive bushing 转盘刹车rotary brake 丝扣油thread lubricant oil 刹把brake crank，brake bar，brake lever 脚踏开关pedal switch 挂档put into gear拉猫头cathead 内钳back-up tongs 外钳lead tongs 气动大钳pneumatic tongs 液压大钳hydraulic tongs 机械手mechanical arm 铁钻工machine hand 司钻房driller room有故障it has broken down, it has something wrong 已修好the breakdown has been fixed马上去go there at once 请下去please go down 请上来please come up躲开，危险get out，danger 请翻译来ask the interpretor to come here 冲洗flushing井口well-head（well head）井下落物fish 一根钻杆（单根）single（pipe）三根钻杆组合（立根）thribble 甩单根breaking down 接单根make a connection气动绞车pneumatic drawworks 吊篮basket 卡子clamp 绳套rope sling loosening紧固tightening 挪开move it off 换班change，shift 保养设备maintain equipment钻井日志boring journal，boring log 油管悬挂器tubing hanger第5节钻井工程井口作业实用词汇与短语喇叭口bell mouth，flare opening 贮能器accumulater 液压阀hydraulic valve液压管hydraulic hose 阻流管choke line 井控管汇well control manifold泄压阀pressure relief valve 调压针阀pressure regulating needle valve回压阀backpressure valve 井口螺丝the bolt of wellhead 井口绞车well head drawworks水刹车water brake，hydraulic brake 电缆（electric）cable 井口压力wellhead pressure隔水导管conductor riser 小心滑倒Guard against slipping 不要掉下去Take care not to fall down 我来清理let me clean up 带把扳手来bring a spanner，please 带把铁锤来bring a hammer，please. 带点密封剂bring a little sealant，please 带个密封圈bring a sealing washer 用起子撬prize with （using）screwdriver 用手推注push by hand 卸下来了it has been removed off 装配好了it has been assembled 很快就好了it will be finished right away抬一下let’s lift it 上紧螺丝tighten the screw loosen 松开螺丝loosen the screw把绳子给我give me the rope，please 把绳子拿走take the rope away。
石油钻井英语缩写及词汇
石油钻井英语缩写及词汇石油钻井英语缩写及词汇DC: drill collar钻铤DP: drill pipe钻杆HWDP: heavy weight drill pipe加重钻杆X/O: crossover转换接头CSG: casing 套管WOC: wait on cementing侯凝POOH: put out of hole起钻（trip out）短起：short tripRIH: run in hole下钻（trip in）R/U: rig up组装N/U: nipple up组装L/D: lay down甩钻具DD：directional driller：定向司钻（斯伦贝谢的员工）w/: withBOP: blowout preventer防喷器、封井器BHA: bottom hole assembly井底钻具OD: outside diameter外径ID: inside diameter内径IF: internal flush内平FH: full hole贯眼EU: external upset外加厚IU: internal upset内加厚WBM: water base mud水基泥浆OBM: oil base mud油基泥浆TIW: Texas Iron Works全开安全阀MW: mud weight泥浆密度SPP: standpipe pressure立管压力MWD: measure while drilling随钻测量CCL: casing collar log套管接箍测井GR: gamma ray伽马（测井）HTHP: high temperature & high pressure高温高压RPM: round per minute转速SPM: stroke per minute泥浆泵TD: total depth总井深MD: measured depth斜深TVD: true vertical depth垂深PPG: pound per gallonRKB: rotary kelly bushing方钻杆补心GL: ground level地表LCM: loss circulation materials堵漏剂P/U: pick up上提WOB: weight on bit钻压VISC: viscosity泥浆粘度N/D: nipple down拆卸R/D: rig down拆卸SX: sacks袋、包BBL: barrel桶B/U: bottom up循环一周M/U: make up组装LB: poundPSI: pound per square inchESD: emergency shutdown紧急关停装置ROP: rate of penetration进尺速度（机械钻速）ESP：emergency response plan应急响应预案Isolation valve高低压闸门Swab 凡尔提（泥浆泵配件）Hub方卡瓦Bail 吊环Air hoist气葫芦Chain hoist手拉葫芦、倒链V-door (pipe ramp) 斜坡Flowline泥浆天槽Gas buster / poor boy液气分离器Slug pit配浆罐（配药罐）Trip nipple旋转头喇叭口Rotating head旋转头Chickson 活动弯头Trailer/container/cabin/quarter room住井房/生活区Trash pump排污泵Flare pit放喷池/点火池/防火墙pup joint：短节重晶石：bariteWear bushing：防磨套膨润土：gelCasing tally：套管数据Float shoe：浮鞋Float collar：浮匝Protector：护丝WDC：wait on cement：候凝Measure out of hole：校对井深surface casing：表层套管intermediate casing：技术套管production casing：生产套管方瓦：hub卡瓦：slip碳酸钙：calcium carbonate环形防喷器：annular 半封：pipe ram全封：blind ram Drift ：通径（vt）Gauge ring：通径规Resistivity：电阻套压：casing pressure油（管）压：tubing pressure XJH：须家河地层KOP：kick-off point：造斜点。
石油专业英语(钻井)课件
石油专业英语（钻井）2008-08-02 21:02Drilling 钻井Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业. Prepared bell nipple. 准备”喇叭口”短节.Make up 2 joints of drill pipe. 接两根钻杆.Break out this connection. 卸开该接头.Run hole opener to sea bed. 下扩眼器到海底Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆.Make up bottom hole assembly. 组合下部钻具Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.Number stands on trip out and trip in. 起下钻时给立柱编号.Pick up BHA and run to seafloor. 将下部钻具下到海底.Pick up stands. 接立柱（一个立柱就是三根钻杆接在一起）Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱Drop TOTCO. 投(陶特)测斜仪Fish TOTCO with overshot. 用打捞筒捞起测斜仪Resume drilling to T.D. 继续钻进到总深Circulate 15 minutes.循环15分钟Run in hole. 下钻Put out of hole. 起钻Make an inventory of all ring gaskets. 开一个所有垫圈的清单Use spinning tong. 使用气动扳手Operate the air winch. 操作气动绞车Lay down 57 joints of 5”drill pipe. 甩57根钻杆Pick up drill stem test tool. 提起钻杆测试工具Circulate mud for 2 hours. 循环泥浆2小时Move string during circulation. 在循环时注意活动钻具Circulate hole clean. 循环清洗井眼Circulate bottoms up. 循环泥浆几周Fill up every 5 stands. 每5柱灌泥浆一次Check mud weight every 15 minutes.每15分钟检查泥浆比重Reverse out excess cement. 反循环替出多余的泥浆Change/replace old mud by new mud.用新的泥浆替换出旧的泥浆Stop drilling. 停止钻进Drilling ahead. 钻进Pull out of hole bit. 起出钻头Change bit. 换钻头Run the wear bushing. 下抗磨补心The bit thread type is regular pin. 钻头丝扣是正规公扣What’s the make-up torque? 上扣扭矩要多大?Run in 9”collars. 下9”钻铤The cathead can’t give enoughtorque. 猫头力量不够Connect crossover sub. 接上配合接头The tong angle is too small. 大钳的角度太小了地质年代术语英汉对照2008-08-0221:04stratum 地层stratigraphic correlation 地层对比horizon 层位key bed 标志层barren bed 哑层lacuna 缺失hiatus 间断continuity 连续discontinuity 不连续conformity 整合unconformity 不整合angular unconformity 角度不整合para-unconformity 平行不整合geochronologic unit 地质年代单位eon 宙era 代period 纪epoch 世stage 期chron 时chronostratigraphic unit 年代地层单位eonothem 宇erathem 界system 系series 统stage 阶chronozone 时带biostratigraphic unit 生物地层单位biostratigraphic zone 生物地层带lithostratigraphic unit 岩石地层单位group 群formation 组member 段bed 层geochronologic scale 地质年代表Phaneozoic Eon(Eonothem)显生宙（宇）Cainozoic Era(Erathem) 新生代（界）Cenozoic Era(Erathem) 新生代（界）Quaternary Period(System) 第四纪（系）Holocene Epoch(Series) 全新世（统）Pleistocene Epoch(Series) 更新世（统）Tertiary Period(System) 第三纪（系）Neogene Period(System) 新第三纪（系）Pliocene Epoch(Series) 上新世（统）Miocene Epoch(Series) 中新世（统）Paleogene Period(System) 老第三纪（系）Oligocene Epoch(Series) 渐新世（统）Eocene Epoch(Series) 始新世（统）Paleocene Epoch(Series) 古新世（统）Mesozoic Era(Erathem) 中生代（界）Cretaceous Period(System) 白垩纪（系）Jurassic Period(System) 侏罗纪（系）triassic Period(System) 三叠纪（系）Palaeozoic Era(Erathem) 古生代（界）Permian Period(System) 二叠纪（系）Carboniferous Period(System) 石炭纪（系）Devonian Period(System) 泥盆纪（系）Silurian Period(System) 志留纪（系）Ordovician Period(System) 奥陶纪（系）Cambrian Period(System) 寒武纪（系）Cryptozoic Eon(Eonothem) 隐生宙（宇）Proterozoic Eon(Eonothem) 元古宙（宇）Neoproterozoic Era(Erathem) 新元古代（界）Sinian Period(System 震旦纪（系）Mesoproterozoic Era(Erathem) 中元古代（界）Palaeoproterozoic Era(Erathem) 古元古代（界）Archaean Eon(Eonothem) 太古宙（宇）Precambrian 前寒武纪石油钻井词汇Part One SLICK-LINE（钢丝作业）A. TOOLS rope socket 绳帽stem 加重杆roll stem 滚轮加重杆Tungsten stem 钨加重杆Lead stem 铅加重杆link jar 机械震击器tubular jar 管状震击器hydraulic jar 液压震击器spring jar 弹簧震击器knuckle joint 万向节swivel joint 旋转节wellhead adapter 井口变扣短节X-Over 变扣gauge cutter 通井规selective downshift tool 选择性滑套开关工具shiftting tool 移位工具blind box 盲锤L.I.B(lead impression block) 铅印swaging tool 胀管器spear 打捞矛prong grab 内捞矛center spear 外捞矛catcher 捕捉器wirefinder 钢丝探测器Go devil-F.B 平底撞棍Go devil-C.B 刀杆撞棍retriever 钢丝打捞器overshot 卡瓦打捞筒magnetic fishing tool 磁力打捞工具sidewall cutter 刮管刀alligator grab 鳄鱼爪sand bailer 捞沙筒pipe wrench 管钳tong chain 链钳spanner 扳手wireline clamp 钢丝夹hay pulley 地滑轮dump bailer 倾倒筒saw 锯子saw blade 锯条punch 冲子file 锉刀flat file 板锉,扁锉hammer 榔头pliers,vice 老虎钳wire cutter 断线钳forfex 剪刀tongs 大钳,钳子,管钳flat bit tongs 扁嘴钳screwdriver 改锥，螺丝刀wire stripper 剥皮钳,掳线钳wire-stripper pliers 剥线钳B. EQUIPMENTstuffing box 防喷盒lubricator upper section 上防喷管lubricator middle section 中防喷管lubricator lower section 下防喷管blowout preventer(BOP) 防喷器wellhead adapter 井口变扣短节Lincoln pump 林肯泵hand pump assy.for stuffing box 手压泵Fire extinguisher 灭火器hand tool box 手工具箱injector 注油器lifting cap BOP吊帽trolly 防喷管支撑架parasol 阳伞work vice 台钳chain block 链葫芦tie down chain 系紧链fixed pulley 定滑轮wobble pump 手摇泵wire line clamp 钢丝绳夹wire rope sling 绳套,钢丝吊绳winch 绞车winch barrel(drum) 绞车滚筒winch brake 绞车刹车winch drive shaft universal joint 绞车主动轴万向节winch drum shaft 绞车滚动轴winch line 吊装用绳套winch control panel 绞车控制面板winch truck 吊车C. OPERATIONSRTTS Operation for Shoot andPull RTTS完井服务RTTS Operation for CementSqueezing RTTS固井服务（挤水泥）Pulling Y Block 捞Y堵塞器Open SSD(Slide Side Door) 开生产滑套Close SSD(Slide Side Door) 关生产滑套Open Circulating SSD(Slide SideDoor) 开循环滑套Close Circulating SSD(Slide SideDoor) 关循环滑套Running Gauge Cutter 通井Clean up 地面完井放喷Open Drain Valve 砸泻油阀Pulling Test Plug 捞测试阀Running Jet Pump 投射流泵Pulling Jet Pump 捞射流泵Running Flow Regulator 投配水器Pulling Flow Regulator 捞配水器Fishing Drop Bar 捞点火棒Measuring Static Pressure 测静压Measuring Flowing Pressure 测流压Measuring BHPBU(Bottom Hole Pressure Build Up) 测压力恢复Measuring BHP(Bottom Hole Pressure) Testing with Jet Pump 带泵测压（射流泵）Multi-Rate BHP(Bottom Hole Pressure) Testing 系统试井Slick-line Operation for Completion 钢丝配合完井服务Slick-line Operation for acidizing 配合酸化钢丝作业Running Plug 投堵塞器Pulling Plug 捞堵塞器Run Impression Block 下铅印Running Prong 投平衡杆Sand Level detection 探沙面Run Sand Bailer 下捞砂桶Open SSSV(Sub Surface Safety Valve) by Force 强行打开井下安全阀Running Go Devil 剪切钢丝Fishing Slickline 打捞钢丝Running Side Pocket Plug 投偏心堵塞器Pulling Side pocket Plug 捞偏心堵塞器Running Side Pocket Check Valve 投偏心阀Pulling Side Pocket Check Valve 捞偏心阀Sand Sampling 取砂样Stable Test 稳定试井Slickline Swab 抽吸Running Hanger 投悬挂器Pulling Hanger 捞悬挂器D. SPARE PARTSgrease injection control head 注脂头grease oil 注脂油grease oil tank 注脂油桶BOP pump c/w hose 手压泵及管线pressure test hose 试压管线lubricator bleed off manifold 防喷管针阀Martin Decker W-15 oil 马丁代克油Martin Decker WT indicator c/whose 指重器及管线picking for stuffing box 盘根bearing for the sheave for stuffingbox 轴承O-ring for lubricator 防喷管O环ram assembly for BOP 防喷管闸板总成O-ring for BOP BOP O环O-ring for wellhead adapter 井口变扣O环pin 销钉counter head 计数头cable for counter 计数器软轴bearing of hay pulley 地滑轮轴承Part two Pressure gaugeaccordance 一致,和谐accuracy 精确性,正确度acquisition 获得,获得物alignment 校直,调准append 附加,添加,悬挂apply 申请,应用available 可利用的,有用的battery 电池battery housing 电池筒battery tester 电池测量器baud rate 波特率bull nose 底堵cable 电缆,电线cable head 电缆头,电缆接头calculation 计算,考虑calibration 标度,刻度,校准calibration drift 漂移calibration parameter 标定参数cartesian 笛卡儿曲线certification 证书com port 串行通讯端口command 命令,掌握,支配communicate 沟通,交流,通讯compensate 偿还,补偿configuration 构造,结构,配置,外形configure 配置,设定consist 组成,构成control panel 控制面板convert 转换,使转变cross-over between gauge 压力计间变扣crystal 水晶,晶体current 电流damage 危险,损害data acquisition 获得数据decode 解码,译解delta time 累计时间deviate 偏离diagnostic 诊断diameter 直径digital 数字的directory 目录discussion 讨论display 显示器,显示,展示downhole tools 井下工具drain 消耗,耗尽dump data 回放数据durability 耐用性element 元素,元件,成分elevated temperature 高温encoder 译码器,编码器establish 建立,安置filter 过滤,筛选firmware 固件(软件硬件相结合)fixed rate 固定采样率flash 闪光,闪现frequency 频率,周率gauge 压力计graph 图表,曲线图grease for transducer 传感器用油housing 壳,壳体incorporate 合并,混合indicate 指出,显示individual 个别的,单独的install 安装,安置instrument 工具,器械,器具interface box 接口箱interface box 接口箱internal diagnostics 内部诊断lapse 失误,下降,过失linear plot 线性平面图log 日志maintenance 维护,保持manual 手册,指南manufacture 制造,加工merge 合并,并入,结合memory 存储器,内存module 模块observe 观察,观测offer 提供,企图parallel communication 并行通信period 周期,时期plug 堵,塞,插上,插栓port 端口,港口potential 潜在的,可能的presentation 陈述,表达presentation software 操作软件printer 打印机prior 优先的,在前的procedure 步骤,手续program 程序,节目prune 剪除,修剪,删除quality 质量,品质,性质quartz 石英range 范围,射程real time 实际时间record mode 记录模式reduce 减小,缩小,简化remote control 遥控,遥控操作remove 移动,开除,移交require 请求,要求resolution 分辨率response 回答,响应scale 刻度,天平,比例尺select 选择,挑选setup 机构,安装,装备,组织silicone oil 硅油sleep mode 休眠模式spanner for gauge 压力计专用扳手SRO(surface read-out) 地面直读surpass 超过,胜过talk mode 对话模式terminal 终点终端thread grease 丝扣油transducer 传感器,变频器,交换器transient 短暂的,瞬时的transmit 传输,传送,发射信号transport 传送器,运输机transportation box 压力计箱troubleshooting 发现并修理故障truncate 截取,修剪update 更新,校正,修正upload 上载variable rate 可变采样率various 不同的,多样的version 版本,译本volt 伏特voltage 电压wand 棒,棍,杖zoom 放大,缩放Part three PVT取样 air chamber plug extractor 空气室拉出手柄air chamber plug retaining ringextractor 梭管套旋出手柄air chamber tube assy 导流管air hose assy. 扫空管allen key 内六角autoclave vacuum nipple 抽真空头B/bench hose assy. 样瓶转样管back-up ring 背环compression spring 压缩弹簧filler funnel 漏斗flow regulator body 节流器flow regulator end cap 端帽flow regulator extractor 节流器拉出手柄fuse/110V 保险丝/110Vglycol 甘醇heating jacket for cylinder 样瓶加温器heating jacket for sampler 取样器加温器holder 装配手柄internal circlip 内簧卡internal circlip for cylinder 取样瓶卡环lock grubscrew 锁紧螺丝needle valve 针阀needle valve assy.extractor 针阀手柄needle valve body 针阀组件needle valve BUR former 针阀背环工具off ball 钢球off diskspring 弹簧片piston assy. 活塞总成piston removal 活塞移位工具piston ring 活塞环piston rod 活塞杆piston valve stem 梭阀杆pols-lock pin 锁定销钉pols-lock spring 锁定销钉弹簧posi lock pin depressing tool 锁定按压工具prime hand pump 注油器prime hand pump adaptor 注油器适配器prime port adaptor assy. 加压口适配器prime port nipple plug 加压口堵头prime port spanner 加压阀扳手prime pump assy. 手压泵适配器prime pump hose assy. 手压泵输出管push rod 推杆relief valve stem 调压阀杆retaining ring 制动环reversible circlip pliers 卡簧手钳safety solvent 清洗液sample analysis 试样分析,样品分析sample analyzer 试样分析器sample bailer 采样筒sample blob 井底取样器sample bomb 高压取样瓶,样品存储器sample bottle 取样瓶,采样瓶sample bottle valve adaptor 样瓶接头sample chamber 样品室sample cock 取样旋塞,取样拷克sample collection 取样,样品收集sample collection procedure 取样点,采样点sample collector 取样程序sample connection 试样收集器,采样员sample container 取样接头sample contamination 样瓶,样筒,样品容器sample cup 样品污染sample cylinder 样品杯sample cylinder tag 样瓶,样筒sample date 样瓶标签sample depth 取样日期sample frequency 采样深度sample hose 采样信号sample identification 取样井,采样井sample integrity 采样频率sample interval 样品管,采样胶皮管sample period 样品鉴定sample point 样品的真实性sample signal 取样间隔,取样速度sample well 取样周期sampler hose assy. 取样器软管总成setting screw 制动螺丝setting fork 导流叉管setting tool 空气定位销手柄setting tool 梭杆推进套shuttle mechanism assy. 触发机构tee ring seals T型密封环test gauge 压力表tool body clamp 取样器夹具tool dressing aids 更换'O'环工具torque wrench 扭矩扳手torque wrench adaptor 扭矩扳手接头torque wrench adaptor 扭矩扳手接头transfer bench assy. 转样器总成transfer lock sleeve 转样护帽transfer port adaptor 转样适配器transfer port plug 转样口堵头trigger mech. assy. 触发机构总成trigger spring 触发弹簧vacuum hand pump 真空泵vibra gauge 压力表Part four OthersAa directional engineer 定向井工程师a drilling engineer 钻井工程师a drilling supervisor 钻井监督a senior mud engineer 高级泥浆工程师a toolpusher 队长，技师abandoned drill 弃船演习accelevator 促凝剂acidity 酸性adapter 接头additive 添加剂/处理剂ahead water 先行水air chamber 空气包air hoist 气动绞车alarm 警报alkalinity 碱性泥浆比重amplitude log 声幅测井anchor 锚angle 角钢annular return velocity 泥浆返回流速annular space 环形空间annular velocity 环空流速apparent viscosity 视黏度asbestos 石棉assistant tug boat 护航船assistant driller 副钻aviation fuel 航空油Bback off 倒扣back pressure 回压back pressure valve 回压阀ball 球ball up 泥包barge engineer 平台工程师barite 重晶石bearing 轴承bearing angle 方位bed 床behind water 尾水bit 钻头bit bearing 钻头轴承bit breaker 钻头装卸器bit cost 钻头成本bit diameter 钻头直径bit gauge 钻头规bit life 钻头寿命bit nozzle 钻头水眼bit position 钻头位置bit sub 钻头接头bit time 钻头纯钻时间bit tooth 钻头牙齿bit torque 钻头扭矩bit type 钻头型号bit wear 钻头磨损blasting cap 雷管blow out 井喷blow out preventer 防喷器boiler 锅炉bolt 螺栓bolt,nut 螺丝,螺母bore hole 裸眼bore hole well 井壁boring 钻孔bottom hole 井底bottom fill 沉砂bottom hole pressure 井底压力bottom hole pressure 井底压力bottoms up 携带岩屑box 母扣brake 刹车break out 卸扣breech lock 泡栓build up 压力恢复bulk density 堆积密度;松装密度bulk tank 灰罐bumper sub 缓冲器buoyancy coefficient 浮力系数bushing 补芯butane 丁烷Ccable 电缆calcium remover 除钙剂calculating free piont 计算卡点深度calibration 刻度casing 套管,螺纹联接的兀接箍casing head 套管头casing spool 套管四通casing burst pressure 套管破裂压力casing elevator 套管吊卡casing monkey board 套管平台casing pressure 套压casing program 套管程序casing scraper 套管刮管器casing shoe 套管鞋casing sub 套管接头casing tong 套管大钳cathead 猫头cave in 坍塌cement 水泥cement basket 水泥伞cement bond log 固井质量检验cement flush 水泥冲洗cement slurry 水泥浆cement slurry for lead 先行水泥浆cementing 固井cementing line 固井管线cementing pump 固井泵center latch elevator 中开门吊卡centralizer 套管扶正器centrifugal pump 离心泵chain block 倒链change bit 换钻头chart 卡片check valve 单流阀chemical tank 化学药剂缸chemical treatment 化学处理chemicals 化学剂choke 油嘴choke line 阻流管汇choke manifold 试油树christmas tree 采油树circulating pressure 循环压力circulation 循环circulation rate 循环速度clamp 卡子clay contamination 粘土侵clock 时钟clog house 值班房cock 水龙头coefficient of friction 摩擦系数colloid 胶体completion 完井computer 计算机conductor 隔水导管cone 牙轮cone bit 牙轮钻头connector 联结器contamination of mud 泥浆污染contract 合同contractor 承包商control room 控制室conventional mud 普通泥浆cooker 炊事员core 岩心core barrel 取芯筒core bit 取芯钻头core catcher 岩心爪core gun 取芯器core handling tools 取芯工具core recovery 取芯收获率coring 取芯coupling 联接扣cover 外壳crane operator 吊车司机critical velocity 临界速度cross 十字接头cross over,x-over(XO) 大小头，短节，变扣接头，旁通管crossover sub 配合接头crown block 天车cut off workline 割大绳cylinder 缸Ddaily production 日产量deadline 死绳deadline anchor 死绳固定器deck 甲板declination 偏差/方位角degas ser 除气器dehydration 失水densimeter 密度计depth 井深derrick 井架derrick man 架工desander 除砂器desilter 沉淀池, 滤水池detonator 炸药deviation survey 井斜测量diamond bit 金刚石钻头die collar 打捞卡瓦diesel oil 柴油different pressure sticking 压差卡钻directional well 定向井discharge of pump 泵排量dispersing agent 分散剂displace 替diver 潜水员doctor 医生drag 遇阻draw works 绞车drier(dring oven) 干燥计drift angle 倾角drift mandrel 通径规drifting 通径drill pipe 钻杆drill spool 钻井四通drill stem 钻柱drill strings 钻杆拄drill water 钻井水drill collar 钻铤drill floor 钻台drill floor 钻台driller 司钻drilling 钻进drilling technician 钻井技术员drilling assembly 钻具组合drilling break 进尺突然加快drilling cost 钻井成本drilling crew 钻井队员drilling engineer 钻井工程师drilling equipment 钻井装置,钻机drilling line 大绳drilling log 钻井记录drilling ration 钻速drilling recorder 钻井记录仪drilling rig 钻井船drilling troubles 井下事故drum shaft 滚筒轴DST(drill stem test) 延长DST测试dump valve 放泄阀duplex slush pump 双缸泥浆泵DV collar 分级注水泥短接DV port DV孔Eelbow 弯接头electric logging 电测electric submerged pump(ESP) 电潜泵electrician 电工elevator 吊卡elevator link 吊环emulsifier 乳化剂engine room 机舱erecting equipment 安装设备erecting tools 安装工具erode out 刺坏error 误差ethane 乙烷exploration 勘探extended well testing 延长测试external upset 外加厚Ffalse threading 造扣field maintenance 现场维护，现场保养fill line 灌泥浆管线filling up mud 灌泥浆filter cake 泥饼filter paper 滤纸filtration educing agent 降失水剂finger board 指梁fire drill 消防演习fishing 打捞fishing bumper sub 打捞缓冲器fishing jars 打捞震击器fishing job 打捞作业fishing neck 打捞颈fishing tools 打捞工具fishing up 打捞出落鱼flash welded tool joint 闪光焊接接头flashlight 手电float collar 浮箍float shoe 浮鞋floor man 钻工flow 放喷flow line 泥浆出口管线flow rate 流量flow line 出油管flow rate 流速flowing bean(nipple) 油嘴flowing pressure gradient 流压梯度fluid loss 失水量fluorescence 荧光反应formation 地层formation conductivities 地层电导率formation damage 破坏地层fracturing 压裂free pipe 未卡部分钻柱free point 自由点free standing mast 无绷绳轻便井架fresh water 淡水full hole(FH) 贯眼扣function 函数funnel viscometer 漏斗黏度计Ggamma ray 射线gamma ray log 自然测井gas reservoir 气层gas analysis 气体分析gas chromatography 气体色谱仪gas cut 气侵gas in mud 泥浆中气量gas oil ratio 油气比gas out 气侵gas showing 气体显示gasoline 汽油gauge 量规gear 牙轮gel 凝胶gel cement 胶质水泥gel mud 胶质泥浆gel strength 切力generator 发动机geothermal gradient 地温梯度goose neck 鹅颈管grade 级/等级grease 黄油guide shoe 引鞋gun perforation 射孔完井gypsum mud 石膏泥浆Hhammer 锤子hard ware 硬件heavy mud 重泥浆/加重泥浆heavy viscosity mud 高粘泥浆heavy weight drill pipe 加重钻杆heavy bodied 很稠的，粘滞的helicopter 直升飞机helicopter port 飞机平台helmet 安全帽hole opener 扩眼器hole size 井眼尺寸hole straightening 井眼校正/纠斜hook 大钩hook load 大钩负荷hook load off bottom 钻柱离底时大钩负荷hook position 大钩位置hopper 漏斗hose 软管/水龙带hull 船身hydraulic pressure 静水压力hydraulic oil 液压油hydrostatic pressure 静水压力IIF(internal flush) 内平扣indented bolt 齿纹螺栓indented chisel 齿状钻头，牙轮钻头indirect flushing 反循环洗井，反向冲洗induction electrical survey 感应电测井inertia brake 惯性刹车initial gel strength 出切inner barrel 内岩心筒inner string cementing 内管注水泥input 输入insert bit 镶齿钻头inside bop drill 安装回压凡尔演习intake profile 吸水剖面internal upset 内加厚internal-external upset 内外加厚interpreter 翻译invaded zone 侵入带invasion diameter 侵入直径inverse circulation 反洗井inverse well-flushing 反洗井isobutane 异丁烷isopentane 异戊烷Jjack knife mast 折叠式轻便井架jack up type drilling unit 自升式钻井船jars 震击器joint 单根junk basket 打捞蓝Kkelly 方钻杆kelly bushing 方钻杆补芯kelly cock 方钻杆考可kelly down 方入kelly down depth 方入深度kelly drive 方钻杆滚子补芯kelly spinner 方钻杆旋扣器kelly up 方余key seat 键槽key seating sticking 键槽卡钻kick 井涌kick control 控制井涌kill line 压井管汇killing a well 压井Llaminar flow 层流latching elevator 扣吊卡lay down 甩lay time 迟到时间leak 漏life raft 救生筏lifeboat 救生艇lift jacket 救生衣lifting sub 提升短接light weight mud 轻泥浆lignite 铁络盐lignite mud 铁络盐泥浆lime 石灰lime mud 石灰泥浆limit switch 相限开关line 管线line cleaning 管线清洗line test 管线试压liner 缸套,尾管liner hanger 尾管挂living quarters 居住区loading 装船logging cable 测井电缆logging program 测井程序logging tool 测井工具loosen 放松lost circulation 井漏lost circulation materials 堵漏剂lubricating oil 润滑油lubricator(assembly,system) 防喷管（装置，系统）Mmachine oil 机油main tug boat 主拖轮make up 上扣make up torque 上扣扭矩mast 钻机master bushing 转盘大补芯master valve 总闸门material man 材料员mean sea level 平均海平面mechanic 机械工mechanist 机械师methane 甲烷mica 云母milled teeth bit 铣齿钻头milling tool 铣具/磨鞋miring water 溶解水mixing pump 混合泵monkey board 二层台morning tour 白班motormen 机工mouse hole 鼠洞mud 泥浆mud agitator 泥浆搅拌器mud balance 泥浆密度计mud column 泥浆柱mud conditioning 泥浆处理/配泥浆mud conductivity 泥浆导电率mud density 泥浆密度mud ditch 泥浆槽mud flow meter 泥浆流量计mud gun 泥浆枪mud line 泥浆管线mud logging 泥浆录井mud pump 泥浆泵mud resistivity 泥浆电阻率mud retort 泥浆蒸馏水mud return line 泥浆返出管线mud tank 泥浆池mud temperature 泥浆温度mud testing 泥浆测试mud volume 泥浆量mud weight indicator 泥浆比重计mud tank 泥浆罐multiple completion 多层完井MW(mud weight) 泥浆重量,泥浆密度Nnail 钉子natural flow 自喷NDBOPS(nipple down blowout preventers) 卸下防喷器组NDT(nipple down tree) 拆卸井口装置，拆卸采油树near bit stabilizer 金钻头扶正器neutron 中子射线nipple down 卸下，拆卸nipple seating 座落接头no return 未返回水泥浆normal circulation 正循环normal butane 正丁烷normal pentane 正戊烷nozzle size 水眼尺寸nut 螺母Ooff bottom 不接触井底office 办公室oil base mud 油基泥浆oil reservoir 油层on bottom 接触井底open 打开open hole 裸眼opening 扩眼o-ring O环outer barrel 外岩心筒oven 烘箱over pulling 遇卡overshot 打捞筒Ppacker 封隔器packing 密封圈paint 油漆panel 面板paraffin plugging 蜡堵paraffin valve 清蜡闸门paraffin-treatment 清蜡处理paraffin-troubles 结蜡井parts 零件pentane 戊烷PH control additive PH控制剂phenolphthalein 酚酞pile hammer 打桩机pin 销子,公扣pincers 钳子pipe wrench 管子扳手piston 活塞piston rod 活塞杆pit drill 防喷演习pit level 泥浆液面pit level 泥浆池液面pit volume increase 泥浆增加量plastic viscosity 塑性黏度plug 水泥塞plug container 水泥头plug flow 塞流plugging back cementing 回堵注水泥pollution 污染polymer 聚合物portland cement 硅酸盐水泥potassium chlorate 氯化钾power slip 动力卡瓦power source 电源power swivel 动力水龙头power tong 动力大钳power law model 幂律模型pressure decline 压力降pressure equilibrium 压力平衡pressure gage 压力表pressure gradient 压力梯度pressure gradient 压力梯度pressure loss 压力损失pressure loss in pipe 管内压力损失pressure of mud column 泥浆柱压力pressure loss in annular 环空压力损失pressurized air 压缩空气preventer of double ram type 双闸板式防喷器production 生产propane 丙烷pry bar 撬杠，杠杆pull out of the hole 起钻pulley 滑轮pulley 滑轮pulling slip 起卡瓦pumice 浮石pump count 累计泵冲数pump efficiency 泵效pump pressure 泵压pump speed 泵速pump stroke counter 泥浆泵冲数pup joint 短接put into gear 挂挡put on break 刹车，制动PWV(production wing valve) 生产翼阀Qquick coupling 快速接头，快接管箍Rradio operator 电报员radioactivity log 放射性测井rag line 大棕绳rain density 颗粒密度rat hole 鼠洞rate of penetration 转速reamer 释放，丢手reaming 辊轴扶正器recorder 划眼red lead 记录仪reducer 丝扣油，铅油，管件润滑油regular 大小头release 正规扣relief valve 泄压阀,泄流阀reserve pit 储存池reservoir pressure 油层压力retarder 缓凝剂return 返回水泥浆return mud 反出泥浆returning fluid 井口反出液reverse circulation 反循环reverse circulation 反循环revolution 运转revolution 转数revolutions per minute 每分钟转数Reynolds number 雷诺数rig down 拆卸钻机rig up 安装钻机rig in 安装,连接rig out 拆卸ring gasket 钢圈/垫圈riser 隔水导管rope damp 绳头,绳卡rotary hose 泥浆水龙带rotary slip 转盘卡瓦rotary speed 转盘转数rotary table 转盘rotation bases 倒班roughneck 钻工roustabout 水手run casing 下套管run in the hole 下钻run length 进尺run bridge plug 下桥塞run gauge cutter 通井running tool 下入工具running in test 试车running repair 日常修理,现场维修RWTO(returned well to production) 井恢复生产Ssafety belt 安全带safety clamp 安全卡子safety joint 安全接头safety valve 安全阀sampling depth 取样井深sampling interval 取样间隔sand bridge 砂桥sand trouble 砂堵sandline 捞砂绳saturated salt-water mud 饱和盐水泥浆screw 螺钉seal 密封/封堵seating nipple 座落接头sea-water mud 海水泥浆sensor 传感器separater 分离器set back 立根盒setting slip 放卡瓦shaft 轴shale shaker 振动筛shallow gas 试气层shear rate 剪切速度shear pin 剪切销钉sheave 滑轮shock sub 减振器shoe guide 引鞋short trip 短起下钻shut in 关井shut in casing pressure 关井套管压力shut in drill pipe pressure 关井钻杆压力shut in pressure 关井压力shut off 关闭side wall neutron log 井壁中子测井silicon flour 硅粉silicon-controlled rectifier 可控硅整流器single joint elevator 单根吊卡single ram 单闸板slip 卡瓦slip type elevator 卡瓦式吊卡slip velocity 沉积速度slip workline 倒大绳slow pump 低泵速sludge tank 加重泥浆池slush pump 泥浆泵socket 插座solid content 固体含量sonic log 声波测井sonic wave 声波spacer 隔离液spare parts 备件spider 卡盘spontaneous potential log 自然电位测井spool 四通spring 弹簧spud in 开钻squeeze cementing 挤水泥stabilizer 扶正器stabilizing agent 稳定剂stage cementing 分级注水泥stainless steel 不锈钢stand 立柱stand pipe 立管stand the test 试验合格,经受考验standby 待机stand-by boat 值班船starting outfit 启动设备static pressure 静压steam 蒸气sticking 卡钻/被卡stinger 导向插头,引鞋,尾管stinger sub 插入式短节stop lost circulation 堵漏storm 风暴straight well 直井眼sub 接头,短接submerged pump 潜水泵substructure 井架底座sucking line 上水管线suction tank 吸入池supercharge pump 泥浆灌注泵supervisor 监督supply boat 供应船support 支架surge pressure 冲击压力suspending weight 悬重swab pressure 抽吸压力swabbing 抽吸switch 开关TT/B/G 牙齿/轴承/外径磨损table torque meter 转盘扭矩表table height 转盘高度taper milling 锥形刮刀technician 技术人员，技师tee 三通temperature log 温度测井ten minutes gel 终切test paper 试纸thread 丝扣tie back tool 回接工具tighten 上紧TOF(top of fishing) 落鱼顶部tong 大钳tong torque meter 大钳扭矩表ton-mile 吨-英里TOOH(tool out of hole) 起出下入井中的工具tool joint 钻杆接头tool pusher 钻井技师top valve 采油树清蜡闸门,试井闸门torch burner 喷灯torque 扭矩total depth 总井深total gas 气全量total pit 泥浆池总体积tour Shift 班towing 拖航transmission 传动装置/变速器traveling block 游动滑车tri-cone bit 三牙轮钻头trip 起下钻trip tank 计量罐tripping time 起下钻时间tubing 油管tubing hanger 油管挂tubing spool 油管四通tubing head 油管头tubing pressure 油压turbo drill 涡轮钻具turbulent flow 紊流twist off 脱扣typhoon 台风Uunconnect switch 非接触式开关unfreezing 解卡unlatching elevator 开吊卡unloading 卸栽upset 加厚Vvalve master 主阀variable density log 变密度测井V－door 井架大门vent pipe 放空管ventilate 放空,吹扫ventilation 通风,通风设备vertical depth 垂直深度viscosity 黏度volume inside pipe 管内容量volume of annulus 环空容量WW.O.O(wait on orders) 等待指令wait on 等指令wait on cement 候凝wait on(stand by) 待命walkie-talkie 对讲机wall scraper 井壁刮刀WAP(well performance analysis) 井的动态分析warning board 警告牌wash over 洗井,套洗,冲刷wash tank 洗罐,分离罐washer 洗衣机wash-over fishing operation 套洗打捞作业,套洗落鱼作业water flood pump(injection) 注水泵water flush 水循环洗井water injector(injection well) 注水井water lost(WL) 泥浆失水wax containing crude 含蜡原油waxy 蜡,蜡状物,含蜡的WDBS(weight going down before sticking) 仪器遇阻前下行重量weather 气候WEG(wireline entryguide) 喇叭口weight in air 空气中重量weight in mud 泥浆中重量weight indicator 指重表weight material 加重剂weight on bit 钻压weighted mud 重泥浆/加重泥浆welder 电焊工well 井well cleaning 洗井well head 井口well head assembly 井口装置well head pressure 井口压力well shooting 地震测井well bean 井口油嘴well blowout 井喷well bore clean up 洗井,well cementation 固井,挤水泥well cementing operation 固井作业well completing data 完井资料,数据well completing fluid 完井液well completinginformation 完井资料, wellcompleting test 完井测试well completion 完井well condition 井况well control device 井控装置well control equipment 井控设备well control fluid 压井液well control information 井控资料well control manifold 井口控制管汇well control operation 压井作业well deflection 井斜well flow under balance 诱喷well killing 压井well killing job 压井作业well killing method 压井方法well performance testing 系统试井,井动态测试,井生产测试well pulling job 起油管作业well pulling service 修井起下作业well sampling 井下取样well sand up 油井砂堵well screen 油井筛管well service tank 修井液罐well service hoist 修井机well service work 修井作业well site illumination 井场照明well testing supervisor 试油,测试监督well-completion practice 完井作业wellhead cap 井口帽wellhead choke 井口油嘴wellhead control valve 井口总阀门wellhead tap 井口短节wetting agent 润滑剂WHP(wellhead platform) 井口平台wiper trip 通井wire 钢丝wire line(WL) 电缆work accident 操作事故work assignment 工作安排work string reciprocation 工。
石油钻井工程英语词汇
地址：北京市朝阳区东三环中路7号财富中心A 座601 邮编：100020石 油 钻 井 工 程英 语 词 汇2008-10-15第一章：石油钻井工程英语基础词汇第1 节 石油钻井工程基础词汇钻井：drill定向斜井：directional drilling欠平衡钻井：under-balance drilling海上钻井：off-shore drilling陆地钻井：on-shore drilling 钻头：drill bit刮刀钻头：drag bit牙轮钻头：rock bit (镶齿钻头insert bit, 钢齿钻头steel toothed bit)金刚石钻头：diamond bit取心钻头：coring bit钻头浮阀：float valve钻头水眼：bit nozzle(or jet)钻头水眼刺:bit nozzle washed out钻头规：bit caliper(bit gauge)钻头泥包：bit is balling钻头钝了，我建议现在起钻：bit is dull. I suggest to POOH now钻铤：DC(drill collar )光钻铤slick drill collar，螺旋钻铤spiral drill collar钻杆：DP(drill pipe )方钻杆：kelly公扣：pin end母扣：box end内平式连接：IF(internal flash)正规式连接：REG(regular)贯眼式连接：FH(full hole)加重钻杆heavy weight drill pipe短钻杆pop joint井下马达：downhole motor涡轮钻具：turbine震击器：drilling jar减震器：absorber下部钻具组合：BHA（bottom hole assembly）钻具扶正器：stabilizer（string stabilizer, near-bit stabilizer）钻机：drill rig钻井泥浆：drilling mud钻井液：drilling fluid钻井设备：drilling equipment油：oil原油：crude oil天然气：nature gas煤层气：coal-bed gas石油：petroleum中国石油（简称）：CNPC（China National Petroleum Corporation ）长城钻井（简称）：GWDC(Great Wall Drilling Company)采油：oil production产油层(目的层)：reservoir( or pay zone)钻进：drilling调整钻井参数以得到理想的机械钻速：play the drilling parameters to get fast ROP起钻：POOH(pull out of hole)下钻：RIH(run in hole)下套管：run casing(or RIH with casing)短起下钻：wiper trip循环泥浆：circulate泥浆：reverse circulate中途循环泥浆：break circulation分段下钻：RIH in stages通井：control trip划眼：reaming倒划眼：back reaming接单根：make connection滑、割大绳：slip and cut drilling line by ton-mile保养设备：maintain the equipment修理设备: repair (or fix) the equipment保养顶驱：service TDS保养冲管：lubricate wash pipe待工日费：standby rate今天零日费：there is no day rate today(zero day rate today)我可以为您做，但必须收费，请理解I can do for you and I have to charge(back charge) you. Please give me full understanding.不在我的职责范围之内，我要汇报领导，一有消息会马上告诉你It is out of my power and I have to report to my boss. I will let you knowas soon as I get news.大鼠洞：rat hole小鼠洞：mouse hole钻具错扣：the connections are crossed钻具粘扣：thread is galled丝扣坏了：the thread is damaged起钻错扣：alternate the connections新钻具或接头磨扣：break in the new tool joint新钻头磨合：break in the new bitPDC 钻头井底造型：shape the PDC bit跳钻：rough drilling( vibrated drilling, bit is bouncing)蹩钻：rough drilling（drilling torque is abnormally high）缩径：tight hole起钻遇卡：get overpull下钻遇阻：set weight部分漏失：partially lost circulation全部漏失：totally lost circulation盲钻：blind drilling堵水眼：bit jets are blocked掉水眼：bit jets are lost憋压：the pressure is built up卸压：release pressure试压：pressure test功能测试：function test双方独自检查：double check地质：geology地质专业人员：geologist物理：physics地球物理勘探：geo-physical exploration.测井：logging电测井作业：wireline logging operation泥浆测井：mud logging井（副词“好”含意）：well拓展记忆：井眼：bore hole油气井：oil&gas well试井：well test井下：down-hole井下作业：down-hole operation第2 节石油钻井方法基础词汇钻井原理：the principles of drilling顿钻钻井：percussion drilling，cable-tool drilling 旋转钻井：rotary drilling大位移井：big distance( or extended ) well侧钻井：sidetracking drilling水平井：horizontal well探井：wildcat，wildcat drilling深井：deep well浅井：shallow well老井：maturing well丛式钻井：cluster well drilling煤层气井：coal-bed gas well生产井：production well报废井：abandoned well停产井：none-production well井下情况：downhole condition第3 节石油钻井技术基础词汇技术规范，技术指标，技术性能：specification拉伸：tension拉伸强度：tensile strength弯曲强度：bending srength最小屈服强度：minimum torsional strength应力：stress压力：pressure应力点：stress point压力降：pressure drop压力梯度：pressure gradient回压：back pressure大气压：atmosphere压差：pressure difference静液柱压力：static fluid cloumn pressure地层压力：formation pressure坍塌压力：collapse pressure破裂压力：fractured pressure液体：liquid固体：solid气体：gas，air正的：positive负的：negative水平的：horizontal垂直的：vertical第4 节石油钻井参数基础词汇钻压：WOB（weight on bit）转盘转速：RPM（rotation per minute）泵压：SPP(slurry pump pressure)泵冲：SPM（stroke per minute）排量：FR(flow rate)大钩负荷：hook load扭矩：torque反扭矩：reactive torque钻速：ROP(rate of penetration)顶驱：TDS(top drive system)钻井周期：drilling period钻井成本：drilling costs井眼尺寸：hole size垂深：TVD(total vertical depth)井深：MDD(measured depth)水平位移：horizontal displacement井斜角：angle( or hole inclination)方位角：azimuth井眼环空：annulus第5 节石油钻井作业现场工作人员名称甲方：oil company(operator)钻井承包商：drilling contractor第三方（分包商）the third party(sub-contractor)钻井经理：drilling manager监督：supervisor钻井监督：DSV(drilling supervisor) or Companyman 地质监督：geologist泥浆工程师：mud engineer固井工程师：cementing engineer泥浆录井工：mud logger钻井队：drilling crew，drilling team钻井1 班：drilling shift one总经理：general manager总工程师：chief engineer项目经理：project manager(country manager)作业经理：operation manager财务经理：financial manger会计：accountant平台经理：rig manager带班队长：tool pusherHSE 监督：HSE officer司钻：driller副司钻：assistant driller井架工：derrick man钻工：roughneck（or floorman）场地工：roustabout泥浆工：mudman发动机工：motorman机械师：mechanic电工：electrician电焊工：welder司机：driver吊车司机：crane operator铲车司机：forklift operator营房经理：camp boss医生：doctor材料员：material man(storekeeper)炊事员：cook翻译：interpreter洗衣工：laundry man厨房服务生：waiter保安：watchman(or security)机械工程师：mechanic engineer第6 节石油作业现场常用工具扳手：wrench螺丝起子：screwdriver多角螺丝起子：Phlilips screwdriver （cross-headed screwdriver）撬杠：bar加长撬杠：cheater bar活动板手：monkey wrench，adjustable wrench钳子：pliers钩子：hook台钳：bench vice钢挫：file榔头：hammer锤击扳手：hammer wrench搬手：spanner内六角扳手：Allen key钢锯：hacksaw砂纸：sandpaper管钳：pipe tongs(pipe wrench)链钳：chain tong千斤顶：jack黄油枪：grease gun吊车：crane牵引绳：tag line电焊条：welding rod拖拉机：tractor推土机：bulldozer硬尺：ruler游标卡尺：Vernier slide油漆：paint铅油：dope油漆刷：paint brush铅油刷：dope brush绝缘胶布：electrical tape电线：wire插头：plug电插座：outlet(receptacle or switchboard)开关：switch螺栓：bolt螺帽：nut垫片：washer钉子：nail手电钻：hand drill钻头：bit工作台：workbench工具箱：toolbox胶水：glue胶棒：glue bar护丝：thread protector手轮：hand wheel脚轰油门：throttle联接法兰：coupling flange(or adaptor flange) 安全带：safety belt安全帽：helmet工作靴：safety boot工衣：coverall棉袄：coat防护眼镜：safety goggle手套：gloves口罩：mouth mask围裙：apron洗眼台：eye washing station灭火机：fire extinguisher消防栓：fire -hydrant水龙头：water tap消防斧：fire fighting axe铲子：shovel手砂轮：emery wheel左转：turn left右转：turn right手势：gesture信号：signal垃圾：waste garbage拖把：mop接头：sub配合接头：X-over ，cross-over提升短节：lifting sub卡瓦：slips放卡瓦：set slips母锥：box tap公锥：taper tap打捞矛：fishing spear安全接头：safety sub柔性短节：flexible joint井口盖子：wellhead cover防喷盒：mud boxBOP 吊装：BOP trolley( BOP hoist) 吊卡：elevator吊环：elevator links安全卡瓦：safety clamp(dog collar) 钻杆架：pipe rack水龙头提环：swivel bail材料房：warehouse绳卡：bullnose clamp(guy anchor) 绳套：sling吊带：soft sling(belt)卸扣：shackle吊装工具：lifting gear维护保养：maintenance内钳：make-up tong外钳：break-out tong液压大钳：power tong液压猫头：E-zy tong兜绳：mule line四通阀：four-way valve三通：Tee软管：hose球阀：ball valve闸板阀：gate valve单流阀：back valve灌注泵：supercharge pump第二章：石油工程常用设备及专业术语第1 节钻井设备部分井架：Derrick(or mast)起（放）井架：erect(lay down) Derrick 底座大梁：sill钢木基础：mat铅锤：plumb水平仪：level架，台：rack立根盒：setback area坡道：V door(or ramp)猫道：catwalk二层台：monkey-board圆井盖：cellar cover天车：crown block防碰天车：crown-o-matic天车梁：crown block beam天车台：water table游动滑车：traveling block钻井大绳：drilling line引绳：guide line穿大绳：string-in drilling line金属线，电线：wire，cable钢丝绳股：strand截断：cutoff滑车，滑轮，皮带轮：pulley(hoist)手拉葫芦：hand pulley吊耳：lifting eye顶驱：top drive大钩：hook大钩弹簧：hook spring大钩销子：hook pin大钩锁紧装置：hook locking device大钩悬挂高度：hook height水龙头：swivel鹅颈管：gooseneck冲管：wash pipe水龙头盘根：swivel packing钻井水龙带: rotary hose( kelly hose)立管：stand pipe立管管汇：stand pipe manifold高压管线：high pressure line由壬：union低压管线：low pressure line传感器：sensor放压管线：relief line转盘：Rotary Table转盘方瓦：master bushing方补心取出装置：bushing handling tool方补心：kelly drive bushing方孔：square opening小鼠洞：mouse hole大鼠洞：rat hole绞车：Drawworks挂合（摘开）绞车：engage(disengage) drawworks液压绞车：hydraulic winch气动绞车：air tugger(air hoist)滚筒：drum( reel)滚筒高速气离合器：high speed clutch滚筒低速气离合器：low speed clutch锚头：cathead液压猫头：E-zy tong上扣猫头：make up cathead卸扣猫头：make out cathead牙嵌离合器：jaw clutch涡磁刹车：eddy current brake(electromagnetic brake) 猫头轴：cathead shaft猫头绳：cathead line死绳：dead line死绳固定器：dead line anchor间隙：gap死绳固定器膜片：dead line diaphragm上扣：make up上扭矩：torque sth卸扣，卸开：break out上紧，固定：tighten（fasten）松开，松扣：loosen加载：load卸载：unload盘式刹车：disc brake刹车总成：brake assembly刹车轴：brake shaft刹车带：brake band刹车片：brake block液压油箱：hydraulic power unit液动试压泵：hydraulic test pump 液压大钳：hydraulic （power）tong 倒档齿轮：reverse gear动力扳手：power wrench吊钳钳头：hinged jaw钳牙：die大钳锁销：latch大钳悬臂：suspension bar平衡重：counterbalance weight吊钳钳臂：tong arm第2 节钻井泵类及相关设备泥浆泵：mud pump活塞：piston活塞杆：piston rod活塞皮碗：piston cup缸套：liner凡尔体：valve body凡尔座：valve seat凡尔箱：pump module阀弹簧：valve spring阀杆：valve lever阀面：valve face阀帽：valve bonnet空气包：pulsation damper充氮气：refill with nitrogen泥浆泵安全阀：pop-off valve卸压管线：release line排出阀：discharge valve吸入阀：suction valve上水滤子：screen油尺：oil-level dipstick灌注泵：supercharge pump冷却水泵：cooling pump潜水泵：submersible pump盘根盒：stuffing box叶轮：impeller单向阀：check valve（single-pass valve）安全阀：safety valve手动阀：manual valve液动阀：hydraulic valve拉杆：tie rod，tension bar压力表：pressure gauge冲数：strokes排量：flow rate80 冲(次)/分：eighty strokes per minute泥浆罐：mud tank倒泥浆：transfer mud循环罐：active tank储备罐：reserve tank起下钻罐：trip tank溢流检查：flow check沉砂罐：satteling tank锥形罐：sand trap震动筛：sahle shaker筛布：screen目数：mash除砂器: desander除泥器: desilter离心机：centrifuge泥浆分配槽：spider box缓冲罐buffer tank第3 节与泵操作有关的实用短语没有压力：No pressure压力过高：The pressure is too high返回太少：Mud return is too few水太少：Water is not adequate.抢修：Rush to repair请看记录：Please check the record没作记录：No record available加化学药品：add chemicals测定比重：measure mud weight(specific gravity) 测定失水：measure water loss泥饼：mud cake测定切力：measure gel strength停泵：stop pump请打手势：Please make a gesture转动一周：turn round a circle垫高一些：put something under it to raise 抓紧：firmly grasp抬高：lift it up拿稳：hold firm打一下：hit once往外拉：pull outward站稳：stand firm小端：small end大端：large end光滑：smooth粗糙：coarse，rough平面：flat弯曲：bending放松：loosen绷直：stretch tight，draw tight冷却：cooling润滑：lubricate过载：overload功率不足：power is not enough.第4 节钻台与底座钻台：drilling floor钻井班组记录：drilling tour record司钻监视器：driller's monitor司钻控制台：driller's console指重表：weight indicator底座：substructure井队活动房：trailer钻台上值班房：doghouse梯子：ladder第5 节井控操作与防喷器溢流: kick溢流征兆: kick sign气侵：gas cut井喷：blow-out1 次井控the primary well control2 次井控the secondary well control3 次井控the tertiary well control平衡balance超平衡over-balance欠平衡under balance漏失试验leak-off test破裂压力fracture pressure额定压力rated pressure工作压力working pressure防喷器组BOP stack安装（甩下）防喷器组：nipple up(nipple down) BOP stack 分流器diverter万能防喷器：annular preventer，bag preventer单闸板防喷器：single ram preventer双闸板防喷器：double ram preventer（防喷器）闸板：pipe ram变芯闸板防喷器variable bore ram全封式防喷器：blind ram剪切防喷器：shear ram内防喷器Inside BOP投入式单流阀DIBPV（Drop in blowout preventer valve）分流关线diverter line节流管汇choke manifold节流阀choke valve旁通阀standby valve调压阀: Pressure regulator手动节流阀manual choke远程节流阀remote choke井口四通drilling spool变径法兰：adapter flange液压控制阀HCR(hydraulic controller)远程控制系统：koomey unit蓄能器：accmulator压井管线：kill line入口：inlet出口：outlet简易除气器：poor-boy degasser真空除气器：vaccum degasser泥浆池液面纪录仪Pit volume recorder(totallizer)泥浆流动传感仪mud flow sensor泥浆增量Pit gains硫化氢侵入H2S influx加重材料Weighted material氮气Nitrogen乙炔：acetylene氧气：oxygen预冲氮气压力Pre-charge nitrogen pressure地脚螺栓连接Studded connection法兰连接Flange connection箍盘连接Hub connection演习：drill急救演习：first aid drill消防演习：fire drill防喷演习：kick drill泄压: bleed off pressure带刻度压力表: calibrated pressure gauge带刻度容（体）积表: calibrated volume gauge套管鞋: casing shoe上部井眼段top hole section快速钻进地层fast drilling formation压实地层：consolidated formation风化地层：weathered formation钻屑携带能力cuttings carrying capacity浅层气藏shallow gas地层破裂formation to break down压力梯度pressure gradient地层压力formation pressure井口压力wellhead pressure漏失压力leak-off pressure破裂压力fractured pressure井底压力BHP( bottom hole pressure)正常压力normal pressure异常压力abnormal pressure静液压力hydrostatic pressure动态压力dynamic pressure环空压力annular pressure关井钻杆压力SIDPP (shut in drill pipe pressure)关井套管压力SICP( shut in casing pressure)最大关井套管压力maximum allowable surface pressure, MAASP 最初循环压力ICP( Initial circulating pressure)循环结束压力FCP(Final circulating pressure)U 形管原理U-tube principle压井操作killing operation补救措施remedial actions关井后循环circulation under well closed in conditioncl 离子含量chloride contentDc 指数Dc exponent软关井soft shut in硬关井hard shut in第1 次循环first circulation第2 次循环second circulation压井泥浆比重kill mud weight抽吸swab激动surge含气地层gas bearing formation含气页岩gas bearing shale安全增量safety margin记录卡片trip sheet低循环泵速SCR(slow circulation rate)当量泥浆密度EQD(equivalent mud density)当量循环密度ECD(equivalent circulating density)司钻压井法driller’s method等待压井法wait & weight method体（容）积法volumetric method下推压井法bull-heading method不压井下钻：snub in第三章：钻井工程作业部分第1 节钻井事故井喷：blow out井涌：kick井漏：lost circulation坍塌，井壁坍塌：cave in(collapse)出砂：sand production砂桥：sand bridge台阶：ledge键槽：keyseat椭圆井眼：oval shaped hole卡钻：sticking填井：pack-hole封井：packed drilling井下落物：fish大幅度活动钻具试图解卡：work the string and try to free it活动钻具以避免卡钻：move(reciprocate ) the string to avoid being stuck. 打捞：fishing鱼头：top of fish打捞工作：fishing job侧钻：side-tracking侧钻井眼：sidetracking hole水泥窜槽：cement channeling固井失败：cement failure防砂：sand control缓慢开泵并仔细观察返浆情况：slowly start pumping and closely watch the return on the shale shaker 第2 节钻头牙轮钻头：rock bit刮刀钻头：drag bit金钢石钻头：diamond bit镶齿钻头：insert bit铣齿钻头：milled tooth bit喷射钻头：jet bit牙轮：cone钻头装卸器：bit breaker钻头直径：bit diameter钻头寿命：bit life钻头磨损：bit wear钻头型号：bit type水眼尺寸：nozzle size水眼效率：nozzle efficiency钻头接头：bit sub第3 节钻具方钻杆：kelly方钻杆旋扣器：kelly spinner方钻杆旋塞：kelly cock钻具：drilling string钻杆：drill pipe油管：tube钻具组合：drilling assembly扶正器：stabilizer扩眼器：reamer（hole opener）钻铤：drill collar无磁钻铤：NMDC(non-magnetic drill collar) 加重钻杆：HWDP(heavy weight drill pipe) 近钻头扶正器：near-bit stabilizer震击器：jar减震器：shock absorber螺旋钻铤：spiral drill collar键槽破坏器：key seat reamer安全接头：safety joint钻杆刮泥器：drill pipe wiper泥浆动力钻具：mud motor钻柱：drill string涡轮：turbine涡轮钻具：turbo-drill stem立根：stand加厚：upset内加厚：IU(internal upset)外加厚：EU(external upset)内外加厚：internal-external upset丝扣：thread打捞颈：fishing neck母扣：box公扣：pin左旋螺纹：left-hand thread右旋螺纹：right-hand thread正规接头：regular joint贯眼接头：full hole joint内平接头：internal flush joint护丝：thread protector快速护丝：easy protector打捞工具：fishing tool打捞作业：fishing operation打捞篮：junk basket卡瓦打捞筒：overshot打捞杯：junk sub牙轮打捞器：cone fisher套管打捞矛：casing spear打捞矛：fishing spear打捞公锥：male tap(fishing nipple)打捞母锥：female tap(fishing socket)倒扣工具：reversing tool(backing-up tool) 铣鞋：milling shoe铣具：milling tool平底铣鞋：flat bottom mill磁力打捞工具：magnetic fishing tool打捞钩：fish hook气动工具：pneumatic tool减摩短节：friction reduction sub下套管漂浮接箍：casing floating coupling 轴向加压器：hydraulic axial thruster第4 节钻井工程地面作业实用词汇与短语方入：kelly-in方余：kelly-up开钻：spud in作业指令：instruction钻井设计：drilling program井身结构：well schematic岩性：lithology迟到时间：lag time(bottom up)换钻头：change bit甩钻具：laydown drill pipe发生故障：break down安装（拆卸）：rig up(rig down)接头：sub adapter机械手：mechanical arm铁钻工：iron roughneck有故障：It fucked up( something is wrong with it)已修好：it has been fixed马上去：Go there at once请下去：Please go down请上来：Please come up躲开，危险：keep away，danger.请翻译来：Ask interpretor come here，冲洗：wash down井口：well-head一根钻杆（单根）：single三根钻杆组合（立根）：thribble吊蓝：cage(basket)换班：shift change第5 节钻井工程井口作业实用词汇与短语喇叭口：bell nipple出水管：mud return line(flow line)试压杯：cup tester小心滑倒：wet floor, be careful不要往井眼内掉东西：never fall down anything inside hole 我来做：Let me do it带把板手来：Bring a spanner，please带点密封剂：Bring a little sealant(Teflon)，please很快就好了：lt will be finshed right away抬一下：Let's lift it把绳子给我：Give me the rope，please不漏：no leakage电焊：welding气焊：gas welding气割：gas cut栏杆：handrail，gangway rail，railing蒸汽：vapour压缩空气：pressurized (compressed) air注意安全：pay attention to safety别动：Don't move，Don't touch.对准：point out exactly.校正：align裸眼：open hole第四章：钻井液及相关设备第1节钻井液名称泥浆：mud钻井液：drilling fluid完井液：completion fluid修井液：work-over fluid压井液：killing fluid射孔液：perforating fluid隔离液：spacer fluid泥浆处理：mud treatment泥浆处理设备：mud treating equipment饱和盐水泥浆：saturated salt-water mud油基泥浆：oil-base mud高粘度泥浆：heavy viscous mud重泥浆：weighted mud重泥浆压钻杆：slug drill pipe起钻倒返泥浆：we have wet pipeduring POOH 重晶石：barite纯碱：soda ash高岭土粉：koaline powder云母片：mica sheet增粘剂：viscosifier稀释剂：diluent (thinner)稳定剂：stabilizer (stabilizing agent)烧碱：caustic soda稀释dilution, thinning水泥凝固cement setting第2 节钻井液设备离心泵：centrifugal pump振动筛跑泥浆：mud overflow shale shaker筛出：shake out混合泵：mixing pump混合漏斗：mixing hopper搅拌器：mud agitator泥浆抢：mud gun岩屑：cuttings沉淀：settle沉积物：deposit吸入：suction吸入罐：suction pit泥浆天平：mud balance游码：slide weight支点：fulcrum刀口：edge调整，校正：adjust粘度计：viscometer第3 节钻井液处理剂包，袋：sack粘土：clay膨润土，般土：bentonite钠：sodium钙：calcium氯：chloride氯化钙：calcium chloride石棉：asbestos分散：dispersal表面活性剂：surface-active material铁络盐：lignite单宁：tannin羧甲基纤维素：carboxymethyl celluose CMC 木纤维：xylogen石灰：lime二氧化钙：calcium oxide粉末：powder薄片：flake溶解：dissolve延迟，妨碍：retard处理剂，添加剂：additives缓凝剂：retarder支撑剂：proppant乳化剂：emulsifier润湿剂：wetting agent稳定剂：stabilizing agent除钙剂：calcium remover降失水剂：filtration-reducing agentPH 值控制剂：PH control additive润滑剂：lubricant消泡剂：defoamer agent破乳剂：emulsion breaker洗涤剂：detergent防膨胀剂：anti-swelling agent粘土稳定剂：clay stable agent稀释剂：thinner封堵剂：plugging agent抑制剂：inhibition agent暂堵剂：temporary plugging agent解堵剂：plugging removal堵漏剂：LCM (lost circulation material)水敏地层：water-sensitive formation分散：dispersal水泥浆：cement slurry流变性：rheological characteristics稳定性：stability稠化时间：thickening-time低密度水泥浆：low-density slurry油气层保护：reservoir protection高渗透性：high-permeability砾石：gravity悬浮：suspension固化：solidification.防膨胀：anti-swelling高凝高粘度：high condensation and viscosity 无毒的：non-poisonous无荧光：non-fluorescence钻井液性能参数Specificaitons of Drilling Fluid 含水：water content密度：density厚度：thickness粘度：viscosity塑性粘度：plastic viscosity含砂量：sand content屈服：yield屈服点：yield point屈服强度：yield strength剪切速率：shear rate剪切强度：shear strength剪切应力：shear stress稀释：dilute适用温度：safe temperature初始切力：initial gel strength终切力：ten-min gel strength触变性：thixotropy剪切稀释：shear thining液体浓度:concentration泥浆柱：mud column层流：laminar flow涡流：turbulent flow气泡：bubble第五章：钻井相关作业第1节取芯部分岩心：core取心钻头：core bit取心筒：core barrel内岩心筒：inner barrel外岩心筒：outer barrel岩心爪：core catcher取心工具：corehandling tools取心收获率：core recovery rate取样器：sample blob取样盒：sample box样品筒：sample chamber取样工：sample catcher取样间隔：sample interval井壁取心：side-wall coring井壁取心枪：side-wall coring gun取芯失败：coring failure第2 节固井部分固井：cementing完井：well completion水泥：cement井口：wellhead井口压力：well head pressure井口回压：back pressure on the well head套压：casing pressure导管：conductor表层套管：surface casing技术套管：protective casing(intermediatecasing) 油层套管：production casing尾管：liner尾管悬挂器：liner hanger通径轨：rabbit封隔器：packer联顶节：landing joint套管柱casing string套管下部结构(含套管鞋、浮箍)：casing track(including casing shoe, float collar) 套管扶正器：centralizer止退环：stop collar口袋：pocket( rat hole)环空注水泥作业：top cement job碰压：bump plug隔离液：spacer分级箍：stage collar水泥粘结强度strength of cement bond套管钳：casing tongs套管接箍：casing coupling套管头：casing head散装水泥：bulk-cement水泥浆：cement slurry插管注水泥：stab in cementing插入密封接头：stab in adapter分级注水泥：stage cementing先行水泥浆：lead cement slurry末端水泥浆：tail cement slurry促凝剂：accelerator替浆：displace with mud水泥面：top of cement固井管线：chicksan line(cementing line)灰罐：silo(bulk tank)候凝：WOC(wait-on-cement)挤水泥：squeeze cement水泥塞：plug第3 节固井水泥浆名称和参数超细水泥浆：ultrafine slurry普通水泥浆：normal slurry纤维水泥浆：fiber-reinforced cement slurry膨胀水泥浆：expanding cement slurry低密度水泥浆：low-density slurry水泥体积收缩：cement volume contraction水泥浆水化期间：cement slurry hydrating period 水泥胶结质量：cement sheath bonding quantity 失水率：the rate of water loss析水：liberate water稠化时间：thickening time凝固强度：cementation strength渗透性：permeability，膨胀率：expansion rate压缩强度：compression strength流动性：mobility第4 节测井部分电测：wireline logging测井解释：logging interpretation随钻测井：LWD(logging while drilling)测井电缆：logging cable测井工具：logging tool自然电位测井：spontaneous potential log感应电测井：induction electrical survey双感应测井：dual induction-laerolog中感应测井：medium induction log数字记录：digital record照相记录：photographic recording放射性测井：radioactivity log声波技术：acoustic wave technology仪器耐温：the temperature resistance of the instrument仪器耐压：pressure resistance of instrument油气比：GOR (gas oil ratio)第六章：井下作业常用短语修井：work-over修井工具：work-over tool井下操作：down-hole operations.产层污染：pollution of pay zone增产措施：stimulations压裂和酸化：fracturing or acidizing酸化处理：acid treatment人工压裂：artificial fracturing重复压裂过程：repetition presses for fracturing，压裂车：fracturing truck sets压裂后反映：post-fracture response固体和液体添加泵：solid and liquid additive pump泵交联：pumping cross link交联剂：cross-linking agent排量：discharging三维压裂：three-dimension fracturing对压裂参数的监控、分析和解释：real time monitoring，analyzing and interpreting for fracturing operation parameters压裂操作：fracturing operation压裂规模：fracturing scale化学吞吐：chemical disposal乳化降粘：emulsification declining viscosity增注：augmented injection.注水：water-injection裸眼砾石填充完井：bore hole gravel packer completion.开窗铣锥：open-window mill prick，开窗斜向器：open-window inclined implement碳酸盐岩：carbonate reservoir第七章：海上钻井作业¨海上钻井：offshore drilling陆地钻井：on-land drilling海滩：sea beach浅海：shallow sea海底管线：sea-bottom pipe海底电缆铺设：setting cable under sea-bottom平台安装：platform installation钻井平台：drilling platform顺风：tail wind逆风：against the wind摄氏零下…度：belo w…degree centigrade启锚：weigh anchor抛锚：drop anchor拖航：drag对讲机：intercom，walkie-talkie上吊茏：Please get on the liftbasket救生衣：life jacket晕船：sea sick控制速度：Control the speed货已送抵：The goods has arrived货物验收：Please check and accept the goods在不远处：Not far from here不方便：lt's not convenient有危险：lt's dangerous防污染：prevent pollution没情况：Nothing happened.第八章：定向井部分定向井：directional well造斜点：ＫＯＰ（kick off point）最大井斜角：maximum hole inclination增斜段：building up section稳斜段：holding section降斜段：drop off section井眼尺寸：hole size长、中、段半径：long，medium and short radius 裸井段：the open hole section水平段：horizontal section固井段：cementing section井斜角测量点：angle point水平位移：horizontal departure(displacement)井眼轨迹：wellbore trajectory优化控制：optimum control筛管：screen pipe长封固段固井：long intervals cementing丛式井：cluster well斜向器：whipstock第九章：石油现场机械传动与机械设备第1 节：动力与传动柴油机：diesel发电机：generator直流（交流）电动机：DC（AC）motor交流电：A.C （alternating current）直流电：D.C （direct current）变压器：transformer传动轴：driving shaft从动轴：driven shaft空调机：air conditioner空气压缩机：air compressor应急发电机组：emergency generator消防水泵：fire pump配电间：distrubution room电动潜水泵：ESP(electrical submersible pump) 锅炉：boiler蒸汽：vapour气压不足：The airpressure is poor操作有问题：Operation is not good电压正常：Voltage is all right绝缘不好：The insulation is bad触电：electric shock温度太高：The tempreture is too high接地：ground短路：short circuit按红色钮：Please push the red button打开：open，turn on，switch on关闭：close，turn off，switch off风扇：fan爬上去：climd up跳下来：jump down接住：catch it拿稳：hold tight平方米：square meter立方米：cubic meter加工：process三项交流电：three-phase AC气罐：air tank偶合器，联轴节：coupling链轮：sprocket链条：chain皮带：belt链条驱动：chain drive皮带驱动：belt drive第2 节机械加工与设备对准，使…成一线：align周围的，环境的：ambient模糊，含糊，不明确：ambiguity退火的：annealed淬火：quench回火：temper阳极：anode阴极：cathode含水的，水的：aqueous装配：assembly增大，增加，增益：augment侧向间隙：back-lash电木，（绝缘）胶木：Bakelite批量生产：bulk production轴承：bearing锥齿轮，伞齿轮：bevel gear（刮刀，刃，叶片：blade坯料：blank吹风，爆炸，喷砂机：blast滑轮组：block and tackle浮子，摆锤：bob镗床，镗孔刀具：borer内孔加工，镗孔：boring瓶颈，薄弱环节：bottleneck平衡点，盈亏临界点：breakeven point 型坯：briquette拉床，铰孔机：broacher拉削，扩孔：broaching大齿轮：bull gear碰撞，曲折，拐点：bump缓冲器，减震器：bumper擦亮，光亮：burnish去毛刺：burring凸轮，偏心轮：cam凸轮轴：camshaft铸造：cast触媒，催化剂：catalyst空化作用：cavitation内腔，空穴，（铸造）型腔：cavity陶瓷的，陶器的，陶瓷制品：ceramic 铁屑，金属屑：chip凿子，扁铲：chisel钳：clamp障碍（物），阻塞（物）：clog离合器：clutch罗盘，指南针：compass凸型的：convex凹型的：concave外形，轮廓；结构，构造：configuration锥形的，锥状的，锥体：conical传送装置，运输机，传送带：conveyor波纹；使成波状：corrugation曲柄，曲拐：crank曲轴：crankshaft蠕动，蠕变：creep圆筒，圆柱体；液缸:cylinder仪表盘，控制板：dashboard静载：dead load碎片：debris模具，钢型，冲模：die模锻：die forge压铸的，模铸的：die-cast不导电的，电解质（的）：dielectric差动齿轮，差速齿轮：differential gear扩散，弥漫：diffusion修饰，打磨，使表面光洁：dress钻床：drill press染色，着色；染料：dye电解质：electrolyte椭圆，椭圆体：ellipse金刚砂：emery侵蚀，冲蚀：erosion蚀刻：etch排出，排气；废气：exhaust消音器：muffler爆炸物，炸药；爆炸（性）的：explosive挤压（成形）；挤出，压出：extrude平面加工：facing测隙规：feeler gauge膜：film精加工：finish柔性的，能变形的，灵活的，适应性强的：flexible 软盘：floppy disc硬盘：hard disk车床：lathe流程图：flow chart起伏，波动：fluctuation开槽，切槽：fluting飞轮：flywheel锻造：forge支点，支轴：fulcrum（龙门）起重机：gantry几何学：geometry花岗岩，花岗石：granite石墨：graphite润滑脂：grease磨碎，研磨，磨削加工：grinding槽，沟，企口：groove陀螺仪，回转仪：gyroscope主轴箱：headstock螺旋形的，螺线：helical螺旋齿轮，斜齿轮：helical gear六角形（的）：hex万向接头，万向联轴节：hooke (cardan) joint,flexible joint 削弱，损害：impair冲击，脉冲：impulse测斜仪：inclinometer（刻度盘上的）指针，（铣床）分度头：index铸模，锭：ingot间歇的，断续的：intermittent内在的，固有的：intrinsic离子：ion夹具，夹紧装置，钻模：jig铰链，关节，肘关节，转向节：knuckle搭接，重叠；研磨，精研，抛光：lapping心轴，紧轴，芯棒：mandrel铣削加工：milling铣刀：milling cutter铣床：milling machine混合，混合物，混合气：mixtrue小孔，注油孔，喷嘴：orifice坑，池，孔：pit枢轴，旋转中心，支点：pivot气动的，气体的，风力的：pneumatic泊松比：Poisson’s ratio抛光：polish细孔，微孔，空隙：pore多孔性，空隙度，气孔，砂眼：porosity。
石油钻井英语（二）
⽯油钻井英语（⼆）钻机与钻井设备Drilling RigA drilling rig is a structure housing equipment used to drill for water,oil,natural gas from underground reservoirs or to obtain mineral core samples. The term can refer to a land-based rig, a marine-based structure commonly called an 'offshore rig' or a structure that drills oil wells called an 'oil rig'. The term correctly refers to the equipment that drills oil wells or extracts mineral samples, including the rig derrick (which looks like a metal frame tower).Sometimes a drilling rig is also used to complete (prepare for production) an oil well. However, the rig itself is not involved with the extraction of the oil, its primary function is to make a hole in the ground so that the oil can be produced.Laypeople may refer to the structure which sits on top offshore wells as a 'rig', but this is not correct. The correct name for the structure in a marine environment is platform. A structure upon which wells produce is a production platform. A floating vessel upon which a drilling rig sits is a floating rig or semi-submersible rig because the whole purpose of the structure is for drilling.Drilling rigs can be small and portable such as those used in mineral exploration drilling, or huge, capable of drilling through thousands of metres of the Earth's crust; large "mud pumps" are used to circulate drilling mud(slurry) through the drill bit and the casing, for cooling and removing the "cuttings" whilst a well is drilled; hoists in the rig can lift thousands of tons of pipe; other equipment can force acid or sand into reservoirs to facilitate extraction of the oil or mineral sample; and permanent living accommodation and catering for crews which may be greater than a hundred people in number. Marine rigs may operate many hundreds of miles or kilometers offshore with infrequent crew rotation.注释 (Notes)：1- laypeople 安装⼈员2- up on which 带介词的定语从句例句：(1) I still remember the day on which we drilled the first well over here.我仍然记得我们在这⾥打第⼀⼝井的⽇⼦。
钻井英语
第一节石油钻井工程基础词汇钻井：drill定向斜井：directional drilling欠平衡钻井：under-balance drilling海上钻井：off-shore drilling陆地钻井：on-shore drilling钻头：drill bit刮刀钻头：drag bit牙轮钻头：rock bit (镶齿钻头insert bit, 钢齿钻头steel toothed bit)金刚石钻头：diamond bit取心钻头：coring bit钻头浮阀：float valve钻头水眼：bit nozzle(or jet)钻头水眼刺:bit nozzle washed out钻头规：bit caliper(bit gauge)钻头泥包：bit is balling钻头钝了，我建议现在起钻：bit is dull. I suggest toPOOH now钻铤：DC(drill collar )光钻铤slick drill collar，螺旋钻铤spiral drill collar钻杆：DP(drill pipe )方钻杆：kelly公扣：pin end母扣：box end内平式连接：IF(internal flash)正规式连接：REG(regular)贯眼式连接：FH(full hole)加重钻杆 heavy weight drill pipe短钻杆 pop joint井下马达：downhole motor涡轮钻具：turbine震击器：drilling jar减震器：absorber下部钻具组合：BHA（bottomhole assembly）钻具扶正器：stabilizer（string stabilizer, near-bit stabilizer）钻机：drill rig钻井泥浆：drilling mud钻井液：drilling fluid钻井设备：drilling equipment油：oil原油：crude oil天然气：nature gas煤层气：coal-bed gas石油：petroleum中国石油（简称）：CNPC（ChinaNational Petroleum Corporation ）长城钻井（简称）：GWDC(Great Wall DrillingCompany)采油：oil production产油层(目的层)：reservoir( or pay zone)钻进：drilling调整钻井参数以得到理想的机械钻速：play the drilling parameters to get fastROP起钻：POOH(pull out of hole)下钻：RIH(run in hole)下套管：run casing(or RIH with casing)短起下钻：wiper trip循环泥浆：circulate泥浆：reverse circulate中途循环泥浆：break circulation分段下钻：RIH in stages通井：control trip划眼：reaming倒划眼：back reaming接单根：make connection滑、割大绳：slip and cut drilling line byton-mile保养设备：maintain the equipment修理设备: repair (or fix) the equipment保养顶驱：service TDS保养冲管：lubricate wash pipe待工日费：standby rate今天零日费：there is no day rate today(zeroday rate today)我可以为您做，但必须收费，请理解I can do for you and I have to charge(backcharge) you. Please give me full understanding.不在我的职责范围之内，我要汇报领导，一有消息会马上告诉你It is out of my power and I have to reportto my boss. I will let you know as soon as I get news.大鼠洞：rat hole小鼠洞：mouse hole钻具错扣：the connections are crossed钻具粘扣：thread is galled丝扣坏了：the thread is damaged起钻错扣：alternate the connections新钻具或接头磨扣：break in the new tool joint新钻头磨合：break in the new bitPDC 钻头井底造型：shape the PDC bit跳钻：rough drilling( vibrated drilling,bit is bouncing)蹩钻：rough drilling（drilling torque is abnormally high）缩径：tight hole起钻遇卡：get overpull下钻遇阻：set weight部分漏失：partially lost circulation全部漏失：totally lost circulation盲钻：blind drilling堵水眼：bit jets are blocked掉水眼：bit jets are lost憋压：the pressure is built up卸压：release pressure试压：pressure test功能测试：function test双方独自检查：double check地质：geology地质专业人员：geologist物理：physics地球物理勘探： geo-physical exploration.测井：logging电测井作业：wireline logging operation泥浆测井：mud logging井（副词“好”含意）：well拓展记忆：井眼：bore hole油气井：oil&gas well试井：well test井下：down-hole井下作业：down-hole operation第2节石油钻井方法基础词汇钻井原理：the principles of drilling顿钻钻井：percussion drilling，cable-tool drilling 旋转钻井：rotary drilling大位移井：big distance( or extended ) well侧钻井：sidetracking drilling水平井：horizontal well探井：wildcat，wildcatdrilling深井：deep well浅井：shallow well老井：maturing well丛式钻井：cluster well drilling煤层气井：coal-bed gas well生产井：production well报废井：abandoned well停产井：none-production well井下情况：downhole condition第3节石油钻井技术基础词汇技术规范，技术指标，技术性能： specification 拉伸：tension拉伸强度：tensile strength弯曲强度：bending srength最小屈服强度： minimum torsional strength应力：stress压力：pressure应力点：stress point压力降：pressure drop压力梯度：pressure gradient回压：back pressure大气压：atmosphere压差： pressure difference静液柱压力：static fluid cloumn pressure地层压力：formation pressure坍塌压力：collapse pressure破裂压力：fractured pressure液体：liquid固体：solid气体：gas，air正的：positive负的：negative水平的：horizontal垂直的：vertical第4节石油钻井参数基础词汇钻压：WOB（weight onbit）转盘转速：RPM（rotationper minute）泵压：SPP(slurry pump pressure)泵冲：SPM（strokeper minute）排量：FR(flow rate)大钩负荷：hook load扭矩：torque反扭矩：reactive torque钻速：ROP(rate of penetration)顶驱：TDS(top drive system)钻井周期：drilling period钻井成本：drilling costs井眼尺寸：hole size垂深： TVD(total vertical depth)井深：MD(measured depth)水平位移：horizontal displacement井斜角：angle( or hole inclination)方位角：azimuth井眼环空：annulus第5节石油钻井作业现场工作人员名称甲方：oil company(operator)钻井承包商：drilling contractor第三方（分包商）the third party(sub-contractor)钻井经理：drilling manager监督：supervisor钻井监督：DSV(drilling supervisor) orCompanyman 地质监督：geologist泥浆工程师：mud engineer固井工程师：cementing engineer泥浆录井工：mud logger钻井队：drilling crew，drilling team钻井1 班：drillingshift one总经理：general manager总工程师：chief engineer项目经理：project manager(country manager)作业经理：operation manager财务经理：financial manger会计：accountant平台经理：rig manager带班队长：tool pusherHSE 监督：HSE officer司钻：driller副司钻：assistant driller井架工：derrick man钻工：roughneck（orfloorman）场地工：roustabout泥浆工：mudman发动机工：motorman机械师： mechanic电工：electrician电焊工：welder司机：driver吊车司机：crane operator铲车司机：forklift operator营房经理：camp boss医生：doctor材料员：material man(storekeeper)炊事员：cook翻译：interpreter洗衣工：laundry man厨房服务生：waiter保安：watchman(or security)机械工程师：mechanic engineer第6节石油作业现场常用工具扳手：wrench螺丝起子：screwdriver多角螺丝起子：Phlilips screwdriver （cross-headed screwdriver）撬杠：bar加长撬杠：cheater bar活动板手：monkey wrench，adjustable wrench钳子：pliers钩子：hook台钳：bench vice钢挫：file榔头：hammer锤击扳手：hammer wrench搬手：spanner内六角扳手：Allen key钢锯：hacksaw砂纸：sandpaper管钳：pipe tongs(pipe wrench)链钳：chain tong千斤顶：jack黄油枪：grease gun吊车：crane牵引绳：tag line电焊条：welding rod拖拉机：tractor推土机：bulldozer硬尺：ruler游标卡尺：Vernier slide油漆：paint铅油：dope油漆刷：paint brush铅油刷：dope brush绝缘胶布：electrical tape电线：wire插头：plug电插座：outlet(receptacle or switchboard)开关：switch螺栓：bolt螺帽：nut垫片：washer钉子：nail手电钻：hand drill钻头：bit工作台：workbench工具箱：toolbox胶水：glue胶棒：glue bar护丝：thread protector手轮：hand wheel脚轰油门：throttle联接法兰：coupling flange(or adaptor flange)安全带：safety belt安全帽：helmet工作靴：safety boot工衣：coverall棉袄：coat防护眼镜：safety goggle手套：gloves口罩：mouth mask围裙：apron洗眼台：eye washing station灭火机：fire extinguisher消防栓：fire -hydrant水龙头：water tap消防斧：fire fighting axe铲子：shovel手砂轮：emery wheel左转： turn left右转： turn right手势：gesture信号：signal垃圾：waste garbage拖把：mop接头：sub配合接头：X-over ，cross-over提升短节：lifting sub卡瓦：slips放卡瓦：set slips母锥：box tap公锥：taper tap打捞矛：fishing spear安全接头：safety sub柔性短节：flexible joint井口盖子：wellhead cover防喷盒：mud boxBOP 吊装：BOP trolley( BOPhoist)吊卡：elevator吊环：elevator links安全卡瓦：safety clamp(dog collar)钻杆架：pipe rack水龙头提环：swivel bail材料房：warehouse绳卡：bullnose clamp(guy anchor)绳套：sling吊带：soft sling(belt)卸扣：shackle吊装工具：lifting gear维护保养：maintenance内钳：make-up tong外钳：break-out tong液压大钳：power tong液压猫头：E-zy tong兜绳：mule line四通阀：four-way valve 三通：Tee软管：hose球阀：ball valve闸板阀：gate valve单流阀：back valve灌注泵：supercharge pump。
有关油井的英文表达
有关油井的英文表达油井（oil well）指任何钻透地球表面（Earth's surface）的钻孔（boring），目的是发现（find）或生产（produce）石油（petroleum/oil/hydrocarbons）。
专门生产天然气的叫气井（gas well）。
油井一般经历五个阶段：计划（planning）、钻井（drilling）、完井（completion）、生产（production）与报废（abandonment）。
首先用钻机（drilling rig）通过钻具（drill string）上的钻头（drill bit）在地上钻出127-914.4毫米的孔（hole），然后在钻孔（borehole）中下钢制油管（steel tubing）与套管（casing）。
套管与钻孔之间还可能需要用水泥（cement）来固定。
套管为井孔（wellbore）提供结构上的整体性（structural integrity），同时隔离（isolate）危险的高压区（high pressure zone）。
随着井深加大，钻头和套管尺寸会变小。
现在的油井通常都有2-5个逐渐变小的井口尺寸。
钻头通过与之连接的钻铤（drill collar）来钻进岩层。
钻井液（drilling fluid/mud）通过钻杆（drill pipe）内部泵入钻头，作用包括冷却（cooling）钻头、提升钻屑（drill cuttings）、避免井壁（wellbore wall）不稳定以及避免岩层液体由于压力进入井眼。
使用过的钻井液用振动筛（shaker）去掉钻屑后返回泥浆池（pit）循环利用。
通过在地面的顶部驱动装置（topdrive/kelly drive）增加额外的10米长的钻杆（joints）来增加钻井深度。
这个过程叫接单根（making a connection）。
三根钻杆叫一个立根或立柱（stand）。
小的钻机使用两根的立根，大的则可以使用四根的立根。
钻井英文
有关油井的英文表达首次分享者：安洁利扣已被分享47次评论(0) 复制链接分享转载删除油井（oil well）指任何钻透地球表面（Earth's surface）的钻孔（boring），目的是发现（find）或生产（produce）石油（petroleum/oil/hydrocarbons）。
专门生产天然气的叫气井（gas well）。
油井一般经历五个阶段：计划（planning）、钻井（drilling）、完井（completion）、生产（production）与报废（abandonment）。
首先用钻机（drilling rig）通过钻具（drill string）上的钻头（drill bit）在地上钻出127-914.4毫米的孔（hole），然后在钻孔（borehole）中下钢制油管（steel tubing）与套管（casing）。
套管与钻孔之间还可能需要用水泥（cement）来固定。
套管为井孔（wellbore）提供结构上的整体性（structural integrity），同时隔离（isolate）危险的高压区（high pressure zone）。
随着井深加大，钻头和套管尺寸会变小。
现在的油井通常都有2-5个逐渐变小的井口尺寸。
钻头通过与之连接的钻铤（drill collar）来钻进岩层。
钻井液（drilling fluid/mud）通过钻杆（drill pipe）内部泵入钻头，作用包括冷却（cooling）钻头、提升钻屑（drill cuttings）、避免井壁（wellbore wall）不稳定以及避免岩层液体由于压力进入井眼。
使用过的钻井液用振动筛（shaker）去掉钻屑后返回泥浆池（pit）循环利用。
通过在地面的顶部驱动装置（topdrive/kelly drive）增加额外的10米长的钻杆（joints）来增加钻井深度。
这个过程叫接单根（making a connection）。
石油专业英语 常用
石油专业英语（常用）油井（oil well）指任何钻透地球表面（Earth's surface）的钻孔（boring），目的是发现（find）或生产（produce）石油（petroleum/oil/hydrocarbons）。
专门生产天然气的叫气井（gas well）。
油井一般经历五个阶段：计划（planning）、钻井（drilling）、完井（completion）、生产（production）与报废（abandonment）。
首先用钻机（drilling rig）通过钻具（drill string）上的钻头（drill bit）在地上钻出毫米的孔（hole），然后在钻孔（borehole）中下钢制油管（steel tubing）与套管（casing）。
套管与钻孔之间还可能需要用水泥（cement）来固定。
套管为井孔（wellbore）提供结构上的整体性（structural integrity），同时隔离（isolate）危险的高压区（high pressure zone）。
随着井深加大，钻头和套管尺寸会变小。
现在的油井通常都有2-5个逐渐变小的井口尺寸。
钻头通过与之连接的钻铤（drill collar）来钻进岩层。
钻井液（drilling fluid/mud）通过钻杆（drill pipe）内部泵入钻头，作用包括冷却（cooling）钻头、提升钻屑（drill cuttings）、避免井壁（wellbore wall）不稳定以及避免岩层液体由于压力进入井眼。
使用过的钻井液用振动筛（shaker）去掉钻屑后返回泥浆池（pit）循环利用。
通过在地面的顶部驱动装置（topdrive/kelly drive）增加额外的10米长的钻杆（joints）来增加钻井深度。
这个过程叫接单根（making a connection）。
三根钻杆叫一个立根或立柱（stand）。
小的钻机使用两根的立根，大的则可以使用四根的立根。
石油钻井工程英语口语基础词汇,了解一下~
钻井：drill定向斜井：directional drilling欠平衡钻井：under-balance drilling海上钻井：off-shore drilling陆地钻井：on-shore drilling钻头：drill bit刮刀钻头：drag bit牙轮钻头：rock bit (镶齿钻头insert bit, 钢齿钻头steel toothed bit)金刚石钻头：diamond bit取心钻头：coring bit钻头浮阀：float valve钻头水眼：bit nozzle(or jet)钻头水眼刺:bit nozzle washed out钻头规：bit caliper(bit gauge)钻头泥包：bit is balling钻头钝了，我建议现在起钻：bit is dull. I suggest to POOH now 钻铤：DC(drill collar )光钻铤slick drill collar，螺旋钻铤spiral drill collar钻杆：DP(drill pipe )方钻杆：kelly公扣：pin end母扣：box end内平式连接：IF(internal flash)正规式连接：REG(regular)贯眼式连接：FH(full hole)加重钻杆 heavy weight drill pipe 短钻杆 pop joint井下马达：downhole motor涡轮钻具：turbine震击器：drilling jar减震器：absorber下部钻具组合：BHA（bottom hole assembly）钻具扶正器：stabilizer（string stabilizer, near-bit stabilizer）钻机：drill rig钻井泥浆：drilling mud钻井液：drilling fluid钻井设备：drilling equipment油：oil原油：crude oil天然气：nature gas煤层气：coal-bed gas石油：petroleum中国石油（简称）：CNPC（China National Petroleum Corporation ）长城钻井（简称）：GWDC(Great Wall Drilling Company)采油：oil production产油层(目的层)：reservoir( or pay zone)钻进：drilling调整钻井参数以得到理想的机械钻速：play the drilling parameters to get fast ROP起钻：POOH(pull out of hole)下钻：RIH(run in hole)下套管：run casing(or RIH with casing)短起下钻：wiper trip循环泥浆：circulate泥浆：reverse circulate中途循环泥浆：break circulation分段下钻：RIH in stages通井：control trip划眼：reaming倒划眼：back reaming接单根：make connection滑、割大绳：slip and cut drilling line by ton-mile保养设备：maintain the equipment修理设备: repair (or fix) the equipment保养顶驱：service TDS保养冲管：lubricate wash pipe待工日费：standby rate今天零日费：there is no day rate today(zero day rate today) 我可以为您做，但必须收费，请理解I can do for you and I have to charge(back charge) you. Please give me full understanding.不在我的职责范围之内，我要汇报领导，一有消息会马上告诉你It is out of my power and I have to report to my boss. I willlet you know as soon as I get news.大鼠洞：rat hole小鼠洞：mouse hole钻具错扣：the connections are crossed钻具粘扣：thread is galled丝扣坏了：the thread is damaged起钻错扣：alternate the connections新钻具或接头磨扣：break in the new tool joint新钻头磨合：break in the new bitPDC钻头井底造型：shape the PDC bit跳钻：rough drilling( vibrated drilling, bit is bouncing) 蹩钻：rough drilling（drilling torque is abnormally high）缩径：tight hole起钻遇卡：get overpull下钻遇阻：set weight部分漏失：partially lost circulation全部漏失：totally lost circulation盲钻：blind drilling堵水眼：bit jets are blocked掉水眼：bit jets are lost憋压：the pressure is built up卸压：release pressure试压：pressure test功能测试：function test双方独自检查：double check地质：geology地质专业人员：geologist物理：physics地球物理勘探： geo-physical exploration.测井：logging电测井作业：wireline logging operation泥浆测井：mud logging井（副词“好”含意）：well拓展记忆：井眼：bore hole油气井：oil&gas well试井：well test井下：down-hole井下作业：down-hole operation。
石油专业英语（钻井）
石油专业英语（钻井）2008-08-02 21:02Drilli ng 钻井Carryout drilli ng operati on in accordance with the drilli ng progra m. 按钻井程序进行钻井作业.Prepared bell nipple. 准备”喇叭口”短节.Make up 2 joints of drill pipe. 接两根钻杆.Breakout this connection. 卸开该接头.Run hole opener to sea bed. 下扩眼器到海底Mix gel fluidfor drilli ng conductor hole. 为钻导管井眼配制高粘度泥浆.Make up bottom hole assembl y. 组合下部钻具Checkand resetcrown-saveron everytour. 每个班都要检查并重新调整天车防碰装置.Number stands on trip out and trip in. 起下钻时给立柱编号.Pick up BHA and run to seaflo or. 将下部钻具下到海底.Pick up stands. 接立柱（一个立柱就是三根钻杆接在一起）Don’t drill faster than 15 minute s for 1 stand. 钻进速度别超过15分钟1根立柱Drop TOTCO. 投(陶特)测斜仪Fish TOTCOwith oversh ot. 用打捞筒捞起测斜仪Resume drilli ng to T.D. 继续钻进到总深Circul ate 15 minute s.循环15分钟Run in hole. 下钻Put out of hole. 起钻Make an invent ory of all ring gasket s. 开一个所有垫圈的清单Use spinni ng tong. 使用气动扳手Operat e the air winch. 操作气动绞车Lay down 57 joints of 5”drill pipe. 甩57根钻杆Pick up drill stem test tool. 提起钻杆测试工具Circul ate mud for 2 hours. 循环泥浆2小时Move string during circul ation. 在循环时注意活动钻具Circul ate hole clean. 循环清洗井眼Circul ate bottom s up. 循环泥浆几周Fill up every 5 stands. 每5柱灌泥浆一次Checkmud weight every15 minutes. 每15分钟检查泥浆比重Reverse out excess cement. 反循环替出多余的泥浆Change/replace old mud by new mud.用新的泥浆替换出旧的泥浆Stop drilli ng. 停止钻进Drilli ng ahead. 钻进Pull out of hole bit. 起出钻头Change bit. 换钻头Run the wear bushin g. 下抗磨补心The bit thread type is regula r pin. 钻头丝扣是正规公扣What’s the make-up torque? 上扣扭矩要多大?Run in 9”collars. 下9”钻铤The cathea d can’t give enough torque. 猫头力量不够Connect crosso ver sub. 接上配合接头The tong anglei s too small. 大钳的角度太小了地质年代术语英汉对照2008-08-0221:04stra tum 地层strati graphi c correl ation地层对比horizo n 层位key bed 标志层barren bed 哑层lacuna缺失hiatus 间断contin uity连续discon tinui ty 不连续conformity整合unconformit y 不整合angula r unconformit y 角度不整合para-unconformit y 平行不整合geochronolo gi c unit 地质年代单位eon 宙era 代period纪epoch世stage期chron时chrono strati grap hic unit 年代地层单位eonoth em 宇erathe m 界system系series 统stage阶chrono zone时带biostratigraphic unit 生物地层单位biostratigraphic zone 生物地层带lithostrati graphi c unit 岩石地层单位group群formati on 组member段bed 层geochronolo gi c scale地质年代表Phaneo zoicEon(Eonoth em)显生宙（宇）Cainoz oi c Era(Erathe m) 新生代（界）Cenozoi c Era(Erathe m) 新生代（界）QuaternaryPeriod(System)第四纪（系）Holoce ne Epoch(Series) 全新世（统）Pleist ocene Epoch(Series) 更新世（统）Tertia ry Period(System) 第三纪（系）Neogen e Period(System) 新第三纪（系）Plioce ne Epoch(Series) 上新世（统）Miocen e Epoch(Series) 中新世（统）Paleog ene Period(System) 老第三纪（系）Oligocene Epoch(Series) 渐新世（统）Eocene Epoch(Series) 始新世（统）Paleocene Epoch(Series) 古新世（统）Mesozo i c Era(Erathe m) 中生代（界）CretaceousPeriod(System) 白垩纪（系）Jurassi c Period(System) 侏罗纪（系）triassi c Period(System) 三叠纪（系）Palaeo zoicEra(Erathe m) 古生代（界）Permia n Period(System) 二叠纪（系）Carboni fero u s Period(System) 石炭纪（系）Devoni an Period(System) 泥盆纪（系）Siluri an Period(System) 志留纪（系）Ordovi c ianPeriod(System) 奥陶纪（系）Cambri an Period(System) 寒武纪（系）Crypto zoicEon(Eonoth em) 隐生宙（宇）Proterozoic Eon(Eonoth em) 元古宙（宇）Neopro teroz oic Era(Erathe m) 新元古代（界）Sinian Period(System震旦纪（系）Mesoprotero zoicEra(Erathe m) 中元古代（界）Palaeo prote rozoi c Era(Erathem) 古元古代（界）Archae an Eon(Eonoth em) 太古宙（宇）Precam brian前寒武纪石油钻井词汇Part One SLICK-LINE（钢丝作业）A. TOOLSrope socket绳帽stem 加重杆roll stem 滚轮加重杆Tungst en stem 钨加重杆Lead stem 铅加重杆link jar 机械震击器tubula r jar 管状震击器hydrau lic jar 液压震击器spring jar 弹簧震击器knuckl e joint万向节swivel joint旋转节wellhe ad adapte r 井口变扣短节X-Over 变扣gaugecutter通井规select ive downsh ift tool 选择性滑套开关工具shiftt ing tool 移位工具blindbox 盲锤L.I.B(lead impres sionblock)铅印swagin g tool 胀管器spear打捞矛pronggrab 内捞矛center spear外捞矛catche r 捕捉器wirefi nder钢丝探测器Go devil-F.B 平底撞棍Go devil-C.B 刀杆撞棍retrie ver 钢丝打捞器oversh ot 卡瓦打捞筒magnet ic fishin g tool 磁力打捞工具sidewa ll cutter刮管刀alliga tor grab 鳄鱼爪sand bailer捞沙筒pipe wrench管钳tong chain链钳spanne r 扳手wireli ne clamp钢丝夹hay pulley地滑轮dump bailer倾倒筒saw 锯子saw blade锯条punch冲子file 锉刀flat file 板锉,扁锉hammer榔头pliers,vice 老虎钳wire cutter断线钳forfex剪刀tongs大钳,钳子,管钳flat bit tongs扁嘴钳screwd river改锥，螺丝刀wire stripp er 剥皮钳,掳线钳wire-stripp er pliers剥线钳B. EQUIPM ENTstuffi ng box 防喷盒lubric atoruppersectio n 上防喷管lubric atormiddle sectio n 中防喷管lubric atorlowersectio n 下防喷管blowou t preven ter(BOP) 防喷器wellhe ad adapte r 井口变扣短节Lincol n pump 林肯泵hand pump assy.for stuffi ng box 手压泵Fire exting uishe r 灭火器hand tool box 手工具箱inject or 注油器liftin g cap BOP吊帽trolly防喷管支撑架paraso l 阳伞work vice 台钳chainblock链葫芦tie down chain系紧链fixedpulley定滑轮wobble pump 手摇泵wire line clamp钢丝绳夹wire rope sling绳套,钢丝吊绳winch绞车winchbarrel(drum) 绞车滚筒winchbrake绞车刹车winchdriveshaftuniver sal joint绞车主动轴万向节winchdrum shaft绞车滚动轴winchline 吊装用绳套winchcontro l panel绞车控制面板winchtruck吊车C. OPERAT IONSRTTS Operat ion for ShootandPull RTTS完井服务RTTS Operat ion for CementSqueez ing RTTS固井服务（挤水泥）Pullin g Y Block捞Y堵塞器Open SSD(SlideSide Door) 开生产滑套CloseSSD(SlideSide Door) 关生产滑套Open Circul ating SSD(SlideSideDoor) 开循环滑套CloseCircul ating SSD(SlideSideDoor) 关循环滑套Runnin g GaugeCutter通井Cleanup 地面完井放喷Open DrainValve砸泻油阀Pullin g Test Plug 捞测试阀Runnin g Jet Pump 投射流泵Pullin g Jet Pump 捞射流泵Runnin g Flow Regula tor 投配水器Pullin g Flow Regula tor 捞配水器Fishin g Drop Bar 捞点火棒Measur ing Static Pressu re 测静压Measur ing Flowin g Pressu re 测流压Measur ing BHPBU(Bottom Hole Pressu re BuildUp) 测压力恢复Measur ing BHP(Bottom Hole Pressu re) Testin g with Jet Pump 带泵测压（射流泵）Multi-Rate BHP(Bottom Hole Pressu re) Testin g 系统试井Slick-line Operat ion for Comple tion钢丝配合完井服务Slick-line Operat ion for acidiz ing 配合酸化钢丝作业Runnin g Plug 投堵塞器Pullin g Plug 捞堵塞器Run Impres sionBlock下铅印Runnin g Prong投平衡杆Sand Leveldetect ion 探沙面Run Sand Bailer下捞砂桶Open SSSV(Sub Surfac e Safety V alve)by Force强行打开井下安全阀Runnin g Go Devil剪切钢丝Fishin g Slickl ine 打捞钢丝Runnin g Side Pocket Plug 投偏心堵塞器Pullin g Side pocket Plug 捞偏心堵塞器Runnin g Side Pocket CheckValve投偏心阀Pullin g Side Pocket CheckValve捞偏心阀Sand Sampli ng 取砂样Stable Test 稳定试井Slickl ine Swab 抽吸Runnin g Hanger投悬挂器Pullin g Hanger捞悬挂器D. SPAREPARTSgrease inject ion contro l head 注脂头grease oil 注脂油grease oil tank 注脂油桶BOP pump c/w hose 手压泵及管线pressu re test hose 试压管线lubric atorbleedoff manifo ld 防喷管针阀Martin Decker W-15 oil 马丁代克油Martin Decker WT indica tor c/whose 指重器及管线pickin g for stuffi ng box 盘根bearin g for the sheave for stuffi ngbox 轴承O-ring for lubric ator防喷管O环ram assemb ly for BOP 防喷管闸板总成O-ring for BOP BOP O环O-ring for wellhe ad adapte r 井口变扣O环pin 销钉counte r head 计数头cablefor counte r 计数器软轴bearin g of hay pulley地滑轮轴承Part two Pressu re gaugeaccord ance一致,和谐accura cy 精确性,正确度acquis ition获得,获得物alignm ent 校直,调准append附加,添加,悬挂apply申请,应用availa ble 可利用的,有用的batter y 电池batter y housin g 电池筒batter y tester电池测量器baud rate 波特率bull nose 底堵cable电缆,电线cablehead 电缆头,电缆接头calcul ation计算,考虑calibr ation标度,刻度,校准calibr ation drift漂移calibr ation parame ter 标定参数cartes ian 笛卡儿曲线certif icati on 证书com port 串行通讯端口comman d 命令,掌握,支配commun icate沟通,交流,通讯compen sate偿还,补偿config urati on 构造,结构,配置,外形config ure 配置,设定consis t 组成,构成contro l panel控制面板conver t 转换,使转变cross-over betwee n gauge压力计间变扣crysta l 水晶,晶体curren t 电流damage危险,损害data acquis ition获得数据decode解码,译解deltatime 累计时间deviat e 偏离diagno stic诊断diamet er 直径digita l 数字的direct ory 目录discus sion讨论displa y 显示器,显示,展示downho le tools井下工具drain消耗,耗尽dump data 回放数据durabi lity耐用性elemen t 元素,元件,成分elevat ed temper ature高温encode r 译码器,编码器establ ish 建立,安置filter过滤,筛选firmwa re 固件(软件硬件相结合)fixedrate 固定采样率flash闪光,闪现freque ncy 频率,周率gauge压力计graph图表,曲线图grease for transd ucer传感器用油housin g 壳,壳体incorp orate合并,混合indica te 指出,显示indivi dual个别的,单独的instal l 安装,安置instru ment工具,器械,器具interf ace box 接口箱interf ace box 接口箱intern al diagno stics内部诊断lapse失误,下降,过失linear plot 线性平面图log 日志mainte nance维护,保持manual手册,指南manufa cture制造,加工merge合并,并入,结合memory存储器,内存module模块observ e 观察,观测offer提供,企图parall el commun icati on 并行通信period周期,时期plug 堵,塞,插上,插栓port 端口,港口potent ial 潜在的,可能的presen tatio n 陈述,表达presen tatio n softwa re 操作软件printe r 打印机prior优先的,在前的proced ure 步骤,手续progra m 程序,节目prune剪除,修剪,删除qualit y 质量,品质,性质quartz石英range范围,射程real time 实际时间record mode 记录模式reduce减小,缩小,简化remote contro l 遥控,遥控操作remove移动,开除,移交requir e 请求,要求resolu tion分辨率respon se 回答,响应scale刻度,天平,比例尺select选择,挑选setup机构,安装,装备,组织silico ne oil 硅油sleepmode 休眠模式spanne r for gauge压力计专用扳手SRO(surfac e read-out) 地面直读surpas s 超过,胜过talk mode 对话模式termin al 终点终端thread grease丝扣油transd ucer传感器,变频器,交换器transi ent 短暂的,瞬时的transm it 传输,传送,发射信号transp ort 传送器,运输机transp ortat ion box 压力计箱troubl eshoo ting发现并修理故障trunca te 截取,修剪update更新,校正,修正upload上载variab le rate 可变采样率variou s 不同的,多样的versio n 版本,译本volt 伏特voltag e 电压wand 棒,棍,杖zoom 放大,缩放Part threePVT取样 air chambe r plug extrac tor 空气室拉出手柄air chambe r plug retain ing ringextrac tor 梭管套旋出手柄air chambe r tube assy 导流管air hose assy. 扫空管allenkey 内六角autocl ave vacuum nipple抽真空头B/benchhose assy. 样瓶转样管back-up ring 背环compre ssion spring压缩弹簧filler funnel漏斗flow regula tor body 节流器flow regula tor end cap 端帽flow regula tor extrac tor 节流器拉出手柄fuse/110V 保险丝/110Vglycol甘醇heatin g jacket for cylind er 样瓶加温器heatin g jacket for sample r 取样器加温器holder装配手柄intern al circli p 内簧卡intern al circli p for cylind er 取样瓶卡环lock grubsc rew 锁紧螺丝needle valve针阀needle valveassy.extrac tor 针阀手柄needle valvebody 针阀组件needle valveBUR former针阀背环工具off ball 钢球off disksp ring弹簧片piston assy. 活塞总成piston remova l 活塞移位工具piston ring 活塞环piston rod 活塞杆piston valvestem 梭阀杆pols-lock pin 锁定销钉pols-lock spring锁定销钉弹簧posi lock pin depres singtool 锁定按压工具primehand pump 注油器primehand pump adapto r 注油器适配器primeport adapto r assy. 加压口适配器primeport nipple plug 加压口堵头primeport spanne r 加压阀扳手primepump assy. 手压泵适配器primepump hose assy. 手压泵输出管push rod 推杆relief valvestem 调压阀杆retain ing ring 制动环revers iblecircli p pliers卡簧手钳safety solven t 清洗液sample analys is 试样分析,样品分析sample analyz er 试样分析器sample bailer采样筒sample blob 井底取样器sample bomb 高压取样瓶,样品存储器sample bottle取样瓶,采样瓶sample bottle valveadapto r 样瓶接头sample chambe r 样品室sample cock 取样旋塞,取样拷克sample collec tion取样,样品收集sample collec tionproced ure 取样点,采样点sample collec tor 取样程序sample connec tion试样收集器,采样员sample contai ner 取样接头sample contam inati on 样瓶,样筒,样品容器sample cup 样品污染sample cylind er 样品杯sample cylind er tag 样瓶,样筒sample date 样瓶标签sample depth取样日期sample freque ncy 采样深度sample hose 采样信号sample identi ficat ion 取样井,采样井sample integr ity 采样频率sample interv al 样品管,采样胶皮管sample period样品鉴定sample point样品的真实性sample signal取样间隔,取样速度sample well 取样周期sample r hose assy. 取样器软管总成settin g screw制动螺丝settin g fork 导流叉管settin g tool 空气定位销手柄settin g tool 梭杆推进套shuttl e mechan ism assy. 触发机构tee ring sealsT型密封环test gauge压力表tool body clamp取样器夹具tool dressi ng aids 更换'O'环工具torque wrench扭矩扳手torque wrench adapto r 扭矩扳手接头torque wrench adapto r 扭矩扳手接头transf er benchassy. 转样器总成transf er lock sleeve转样护帽transf er port adapto r 转样适配器transf er port plug 转样口堵头trigge r mech. assy. 触发机构总成trigge r spring触发弹簧vacuum hand pump 真空泵vibragauge压力表Part four OthersAa direct ional engine er 定向井工程师a drilli ng engine er 钻井工程师a drilli ng superv isor钻井监督a senior mud engine er 高级泥浆工程师a toolpu sher队长，技师abando ned drill弃船演习accele vator促凝剂acidit y 酸性adapte r 接头additi ve 添加剂/处理剂aheadwater先行水air chambe r 空气包air hoist气动绞车alarm警报alkali nity碱性泥浆比重amplit ude log 声幅测井anchor锚angle角钢annula r return veloci ty 泥浆返回流速annula r space环形空间annula r veloci ty 环空流速appare nt viscos ity 视黏度asbest os 石棉assist ant tug boat 护航船assist ant drille r 副钻aviati on fuel 航空油Bback off 倒扣back pressu re 回压back pressu re valve回压阀ball 球ball up 泥包bargeengine er 平台工程师barite重晶石bearin g 轴承bearin g angle方位bed 床behind water尾水bit 钻头bit bearin g 钻头轴承bit breake r 钻头装卸器bit cost 钻头成本bit diamet er 钻头直径bit gauge钻头规bit life 钻头寿命bit nozzle钻头水眼bit positi on 钻头位置bit sub 钻头接头bit time 钻头纯钻时间bit tooth钻头牙齿bit torque钻头扭矩bit type 钻头型号bit wear 钻头磨损blasti ng cap 雷管blow out 井喷blow out preven ter 防喷器boiler锅炉bolt 螺栓bolt,nut 螺丝,螺母bore hole 裸眼bore hole well 井壁boring钻孔bottom hole 井底bottom fill 沉砂bottom hole pressu re 井底压力bottom hole pressu re 井底压力bottom s up 携带岩屑box 母扣brake刹车breakout 卸扣breech lock 泡栓buildup 压力恢复bulk densit y 堆积密度;松装密度bulk tank 灰罐bumper sub 缓冲器buoyan cy coeffi cient浮力系数bushin g 补芯butane丁烷Ccable电缆calciu m remove r 除钙剂calcul ating free piont计算卡点深度calibr ation刻度casing套管,螺纹联接的兀接箍casing head 套管头casing spool套管四通casing burstpressu re 套管破裂压力casing elevat or 套管吊卡casing monkey board套管平台casing pressu re 套压casing progra m 套管程序casing scrape r 套管刮管器casing shoe 套管鞋casing sub 套管接头casing tong 套管大钳cathea d 猫头cave in 坍塌cement水泥cement basket水泥伞cement bond log 固井质量检验cement flush水泥冲洗cement slurry水泥浆cement slurry for lead 先行水泥浆cement ing 固井cement ing line 固井管线cement ing pump 固井泵center latch elevat or 中开门吊卡centra lizer套管扶正器centri fugal pump 离心泵chain block倒链change bit 换钻头chart卡片check valve单流阀chemic al tank 化学药剂缸chemic al treatm ent 化学处理chemic als 化学剂choke油嘴chokeline 阻流管汇choke manifo ld 试油树christ mas tree 采油树circul ating pressu re 循环压力circul ation循环circul ation rate 循环速度clamp卡子clay contam inati on 粘土侵clock时钟clog house值班房cock 水龙头coeffi cient of fricti on 摩擦系数colloi d 胶体comple tion完井comput er 计算机conduc tor 隔水导管cone 牙轮cone bit 牙轮钻头connec tor 联结器contam inati on of mud 泥浆污染contra ct 合同contra ctor承包商contro l room 控制室conven tiona l mud 普通泥浆cooker炊事员core 岩心core barrel取芯筒core bit 取芯钻头core catche r 岩心爪core gun 取芯器core handli ng tools取芯工具core recove ry 取芯收获率coring取芯coupli ng 联接扣cover外壳crane operat or 吊车司机critic al veloci ty 临界速度cross十字接头crossover,x-over(XO) 大小头，短节，变扣接头，旁通管crosso ver sub 配合接头crown block天车cut off workli ne 割大绳cylind er 缸Ddaily produc tion日产量deadli ne 死绳deadli ne anchor死绳固定器deck 甲板declin ation偏差/方位角degasser 除气器dehydr ation失水densim eter密度计depth井深derric k 井架derric k man 架工desand er 除砂器desilt er 沉淀池, 滤水池detona tor 炸药deviat ion survey井斜测量diamon d bit 金刚石钻头die collar打捞卡瓦diesel oil 柴油differ ent pressu re sticki ng 压差卡钻direct ional well 定向井discha rge of pump 泵排量disper sing agent分散剂displa ce 替diver潜水员doctor医生drag 遇阻draw works绞车drier(dringoven) 干燥计drift angle倾角driftmandre l 通径规drifti ng 通径drillpipe 钻杆drill spool钻井四通drillstem 钻柱drill string s 钻杆拄drill water钻井水drillcollar钻铤drillfloor钻台drillfloor钻台drille r 司钻drilli ng 钻进drilli ng techni cian钻井技术员drilli ng assemb ly 钻具组合drilli ng break进尺突然加快drilli ng cost 钻井成本drilli ng crew 钻井队员drilli ng engine er 钻井工程师drilli ng equipm ent 钻井装置,钻机drilli ng line 大绳drilli ng log 钻井记录drilli ng ration钻速drilli ng record er 钻井记录仪drilli ng rig 钻井船drilli ng troubl es 井下事故drum shaft滚筒轴DST(drillstem test) 延长DST测试dump valve放泄阀duplex slushpump 双缸泥浆泵DV collar分级注水泥短接DV port DV孔Eelbow弯接头electr ic loggin g 电测electr ic submer ged pump(ESP) 电潜泵electr ician电工elevat or 吊卡elevat or link 吊环emulsi fier乳化剂engine room 机舱erecti ng equipm ent 安装设备erecti ng tools安装工具erodeout 刺坏error误差ethane乙烷explor ation勘探extend ed well testin g 延长测试extern al upset外加厚Ffalsethread ing 造扣fieldmainte nance现场维护，现场保养fill line 灌泥浆管线fillin g up mud 灌泥浆filter cake 泥饼filter paper滤纸filtra tion educin g agent降失水剂finger board指梁fire drill消防演习fishin g 打捞fishin g bumper sub 打捞缓冲器fishin g jars 打捞震击器fishin g job 打捞作业fishin g neck 打捞颈fishin g tools打捞工具fishin g up 打捞出落鱼flash welded tool joint闪光焊接接头flashl ight手电float collar浮箍floatshoe 浮鞋floorman 钻工flow 放喷flow line 泥浆出口管线flow rate 流量flow line 出油管flow rate 流速flowin g bean(nipple) 油嘴flowin g pressu re gradie nt 流压梯度fluidloss 失水量fluore scenc e 荧光反应format ion 地层format ion conduc tivit ies 地层电导率format ion damage破坏地层fractu ring压裂free pipe 未卡部分钻柱free point自由点free standi ng mast 无绷绳轻便井架fresh water淡水full hole(FH) 贯眼扣functi on 函数funnel viscom eter漏斗黏度计Ggammaray 射线gammaray log 自然测井gas reserv oir 气层gas analys is 气体分析gas chroma togra phy 气体色谱仪gas cut 气侵gas in mud 泥浆中气量gas oil ratio油气比gas out 气侵gas showin g 气体显示gasoli ne 汽油gauge量规gear 牙轮gel 凝胶gel cement胶质水泥gel mud 胶质泥浆gel streng th 切力genera tor 发动机geothe rmal gradie nt 地温梯度gooseneck 鹅颈管grade级/等级grease黄油guideshoe 引鞋gun perfor ation射孔完井gypsum mud 石膏泥浆Hhammer锤子hard ware 硬件heavymud 重泥浆/加重泥浆heavy viscos ity mud 高粘泥浆heavy weight drillpipe 加重钻杆heavybodied很稠的，粘滞的helico pter直升飞机helico pterport 飞机平台helmet安全帽hole opener扩眼器hole size 井眼尺寸hole straig hteni ng 井眼校正/纠斜hook 大钩hook load 大钩负荷hook load off bottom钻柱离底时大钩负荷hook positi on 大钩位置hopper漏斗hose 软管/水龙带hull 船身hydrau lic pressu re 静水压力hydrau lic oil 液压油hydros tatic pressu re 静水压力IIF(intern al flush)内平扣indent ed bolt 齿纹螺栓indent ed chisel齿状钻头，牙轮钻头indire ct flushi ng 反循环洗井，反向冲洗induct ion electr icalsurvey感应电测井inerti a brake惯性刹车initia l gel streng th 出切inner barrel内岩心筒inner string cement ing 内管注水泥input输入insert bit 镶齿钻头inside bop drill安装回压凡尔演习intake profil e 吸水剖面intern al upset内加厚intern al-extern al upset内外加厚interp reter翻译invade d zone 侵入带invasi on diamet er 侵入直径invers e circul ation反洗井invers e well-flushi ng 反洗井isobut ane 异丁烷isopen tane异戊烷Jjack knifemast 折叠式轻便井架jack up type drilli ng unit 自升式钻井船jars 震击器joint单根junk basket打捞蓝Kkelly方钻杆kelly bushin g 方钻杆补芯kellycock 方钻杆考可kellydown 方入kelly down depth方入深度kelly drive方钻杆滚子补芯kelly spinne r 方钻杆旋扣器kellyup 方余key seat 键槽key seatin g sticki ng 键槽卡钻kick 井涌kick contro l 控制井涌kill line 压井管汇killin g a well 压井Llamina r flow 层流latchi ng elevat or 扣吊卡lay down 甩lay time 迟到时间leak 漏life raft 救生筏lifebo at 救生艇lift jacket救生衣liftin g sub 提升短接light weight mud 轻泥浆lignit e 铁络盐lignit e mud 铁络盐泥浆lime 石灰lime mud 石灰泥浆limit switch相限开关line 管线line cleani ng 管线清洗line test 管线试压liner缸套,尾管liner hanger尾管挂living quarte rs 居住区loadin g 装船loggin g cable测井电缆loggin g progra m 测井程序loggin g tool 测井工具loosen放松lost circul ation井漏lost circul ation materi als 堵漏剂lubric ating oil 润滑油lubric ator(assemb ly,system) 防喷管（装置，系统）Mmachin e oil 机油main tug boat 主拖轮make up 上扣make up torque上扣扭矩mast 钻机master bushin g 转盘大补芯master valve总闸门materi al man 材料员mean sea level平均海平面mechan ic 机械工mechan ist 机械师methan e 甲烷mica 云母milled teethbit 铣齿钻头millin g tool 铣具/磨鞋miring water溶解水mixing pump 混合泵monkey board二层台mornin g tour 白班motorm en 机工mousehole 鼠洞mud 泥浆mud agitat or 泥浆搅拌器mud balanc e 泥浆密度计mud column泥浆柱mud condit ionin g 泥浆处理/配泥浆mud conduc tivit y 泥浆导电率mud densit y 泥浆密度mud ditch泥浆槽mud flow meter泥浆流量计mud gun 泥浆枪mud line 泥浆管线mud loggin g 泥浆录井mud pump 泥浆泵mud resist ivity泥浆电阻率mud retort泥浆蒸馏水mud return line 泥浆返出管线mud tank 泥浆池mud temper ature泥浆温度mud testin g 泥浆测试mud volume泥浆量mud weight indica tor 泥浆比重计mud tank 泥浆罐multip le comple tion多层完井MW(mud weight) 泥浆重量,泥浆密度Nnail 钉子natura l flow 自喷NDBOPS(nipple down blowou t preven ters)卸下防喷器组NDT(nipple down tree) 拆卸井口装置，拆卸采油树near bit stabil izer金钻头扶正器neutro n 中子射线nipple down 卸下，拆卸nipple seatin g 座落接头no return未返回水泥浆normal circul ation正循环normal butane正丁烷normal pentan e 正戊烷nozzle size 水眼尺寸nut 螺母Ooff bottom不接触井底office办公室oil base mud 油基泥浆oil reserv oir 油层on bottom接触井底open 打开open hole 裸眼openin g 扩眼o-ring O环outer barrel外岩心筒oven 烘箱over pullin g 遇卡oversh ot 打捞筒Ppacker封隔器packin g 密封圈paint油漆panel面板paraff in pluggi ng 蜡堵paraff in valve清蜡闸门paraff in-treatm ent 清蜡处理paraff in-troubl es 结蜡井parts零件pentan e 戊烷PH contro l additi ve PH控制剂phenol phtha lein酚酞pile hammer打桩机pin 销子,公扣pincer s 钳子pipe wrench管子扳手piston活塞piston rod 活塞杆pit drill防喷演习pit level泥浆液面pit level泥浆池液面pit volume increa se 泥浆增加量plasti c viscos ity 塑性黏度plug 水泥塞plug contai ner 水泥头plug flow 塞流pluggi ng back cement ing 回堵注水泥pollut ion 污染polyme r 聚合物portla nd cement硅酸盐水泥potass ium chlora te 氯化钾powerslip 动力卡瓦power source电源power swivel动力水龙头powertong 动力大钳powerlaw model幂律模型pressu re declin e 压力降pressu re equili brium压力平衡pressu re gage 压力表pressu re gradie nt 压力梯度pressu re gradie nt 压力梯度pressu re loss 压力损失pressu re loss in pipe 管内压力损失pressu re of mud column泥浆柱压力pressu re loss in annula r 环空压力损失pressu rized air 压缩空气preven ter of double ram type 双闸板式防喷器produc tion生产propan e 丙烷pry bar 撬杠，杠杆pull out of the hole 起钻pulley滑轮pulley滑轮pullin g slip 起卡瓦pumice浮石pump count累计泵冲数pump effici ency泵效pump pressu re 泵压pump speed泵速pump stroke counte r 泥浆泵冲数pup joint短接put into gear 挂挡put on break刹车，制动PWV(produc tionwing valve)生产翼阀Qquickcoupli ng 快速接头，快接管箍Rradiooperat or 电报员radioa ctivi ty log 放射性测井rag line 大棕绳rain densit y 颗粒密度rat hole 鼠洞rate of penetr ation转速reamer释放，丢手reamin g 辊轴扶正器record er 划眼red lead 记录仪reduce r 丝扣油，铅油，管件润滑油regula r 大小头releas e 正规扣relief valve泄压阀,泄流阀reserv e pit 储存池reserv oir pressu re 油层压力retard er 缓凝剂return返回水泥浆return mud 反出泥浆return ing fluid井口反出液revers e circul ation反循环revers e circul ation反循环revolu tion运转revolu tion转数revolu tions per minute每分钟转数Reynol ds number雷诺数rig down 拆卸钻机rig up 安装钻机rig in 安装,连接rig out 拆卸ring gasket钢圈/垫圈riser隔水导管rope damp 绳头,绳卡rotary hose 泥浆水龙带rotary slip 转盘卡瓦rotary speed转盘转数rotary table转盘rotati on bases倒班roughn eck 钻工rousta bout水手run casing下套管run in the hole 下钻run length进尺run bridge plug 下桥塞run gaugecutter通井runnin g tool 下入工具runnin g in test 试车runnin g repair日常修理,现场维修RWTO(return ed well toproduc tion)井恢复生产Ssafety belt 安全带safety clamp安全卡子safety joint安全接头safety valve安全阀sampli ng depth取样井深sampli ng interv al 取样间隔sand bridge砂桥sand troubl e 砂堵sandli ne 捞砂绳satura ted salt-watermud 饱和盐水泥浆screw螺钉seal 密封/封堵seatin g nipple座落接头sea-watermud 海水泥浆sensor传感器separa ter 分离器set back 立根盒settin g slip 放卡瓦shaft轴shale shaker振动筛shallo w gas 试气层shearrate 剪切速度shearpin 剪切销钉sheave滑轮shocksub 减振器shoe guide引鞋shorttrip 短起下钻shut in 关井shut in casing pressu re 关井套管压力shut in drillpipe pressu re 关井钻杆压力shut in pressu re 关井压力shut off 关闭side wall neutro n log 井壁中子测井silico n flour硅粉silico n-contro lledrectif ier 可控硅整流器single joint elevat or 单根吊卡single ram 单闸板slip 卡瓦slip type elevat or 卡瓦式吊卡slip veloci ty 沉积速度slip workli ne 倒大绳slow pump 低泵速sludge tank 加重泥浆池slushpump 泥浆泵socket插座solid conten t 固体含量soniclog 声波测井sonicwave 声波spacer隔离液spare parts备件spider卡盘sponta neous potent ial log 自然电位测井spool四通spring弹簧spud in 开钻squeez e cement ing 挤水泥stabil izer扶正器stabil izing agent稳定剂stage cement ing 分级注水泥stainl ess steel不锈钢stand立柱standpipe 立管standthe test 试验合格,经受考验standb y 待机stand-by boat 值班船starti ng outfit启动设备static pressu re 静压steam蒸气sticki ng 卡钻/被卡stinge r 导向插头,引鞋,尾管stinge r sub 插入式短节stop lost circul ation堵漏storm风暴straig ht well 直井眼sub 接头,短接submer ged pump 潜水泵substr uctur e 井架底座suckin g line 上水管线suctio n tank 吸入池superc harge pump 泥浆灌注泵superv isor监督supply boat 供应船suppor t 支架surge pressu re 冲击压力suspen dingweight悬重swab pressu re 抽吸压力swabbi ng 抽吸switch开关TT/B/G 牙齿/轴承/外径磨损table torque meter转盘扭矩表tableheight转盘高度taper millin g 锥形刮刀techni cian技术人员，技师tee 三通temper ature log 温度测井ten minute s gel 终切test paper试纸thread丝扣tie back tool 回接工具tighte n 上紧。
石油钻井工程英语口语基础词汇,了解一下~
石油钻井工程英语口语基础词汇，了解一下~导读：本文石油钻井工程英语口语基础词汇，了解一下~，仅供参考，如果觉得很不错，欢迎点评和分享。
钻井：drill定向斜井：directional drilling欠平衡钻井：under-balance drilling海上钻井：off-shore drilling陆地钻井：on-shore drilling钻头：drill bit刮刀钻头：drag bit牙轮钻头：rock bit (镶齿钻头insert bit, 钢齿钻头steel toothed bit)金刚石钻头：diamond bit取心钻头：coring bit钻头浮阀：float valve钻头水眼：bit nozzle(or jet)钻头水眼刺:bit nozzle washed out钻头规：bit caliper(bit gauge)钻头泥包：bit is balling钻头钝了，我建议现在起钻：bit is dull. I suggest to POOH now钻铤：DC(drill collar )光钻铤slick drill collar，螺旋钻铤spiral drill collar钻杆：DP(drill pipe )方钻杆：kelly公扣：pin end母扣：box end内平式连接：IF(internal flash)正规式连接：REG(regular)贯眼式连接：FH(full hole)加重钻杆heavy weight drill pipe 短钻杆pop joint井下马达：downhole motor涡轮钻具：turbine震击器：drilling jar减震器：absorber下部钻具组合：BHA（bottom hole assembly）钻具扶正器：stabilizer（string stabilizer, near-bit stabilizer）钻机：drill rig钻井泥浆：drilling mud钻井液：drilling fluid钻井设备：drilling equipment油：oil原油：crude oil天然气：nature gas煤层气：coal-bed gas石油：petroleum中国石油（简称）：CNPC（China National Petroleum Corporation ）长城钻井（简称）：GWDC(Great Wall Drilling Company)采油：oil production产油层(目的层)：reservoir( or pay zone)钻进：drilling调整钻井参数以得到理想的机械钻速：play the drilling parameters to get fast ROP起钻：POOH(pull out of hole)下钻：RIH(run in hole)下套管：run casing(or RIH with casing)短起下钻：wiper trip循环泥浆：circulate泥浆：reverse circulate中途循环泥浆：break circulation分段下钻：RIH in stages通井：control trip划眼：reaming倒划眼：back reaming接单根：make connection滑、割大绳：slip and cut drilling line by ton-mile保养设备：maintain the equipment修理设备: repair (or fix) the equipment保养顶驱：service TDS保养冲管：lubricate wash pipe待工日费：standby rate今天零日费：there is no day rate today(zero day rate today) 我可以为您做，但必须收费，请理解I can do for you and I have to charge(back charge) you. Please give me full understanding.不在我的职责范围之内，我要汇报领导，一有消息会马上告诉你It is out of my power and I have to report to my boss. I will let you know as soon as I get news.大鼠洞：rat hole小鼠洞：mouse hole钻具错扣：the connections are crossed钻具粘扣：thread is galled丝扣坏了：the thread is damaged起钻错扣：alternate the connections新钻具或接头磨扣：break in the new tool joint新钻头磨合：break in the new bitPDC钻头井底造型：shape the PDC bit跳钻：rough drilling( vibrated drilling, bit is bouncing) 蹩钻：rough drilling（drilling torque is abnormally high）缩径：tight hole起钻遇卡：get overpull下钻遇阻：set weight部分漏失：partially lost circulation全部漏失：totally lost circulation盲钻：blind drilling堵水眼：bit jets are blocked掉水眼：bit jets are lost憋压：the pressure is built up卸压：release pressure试压：pressure test功能测试：function test双方独自检查：double check地质：geology地质专业人员：geologist物理：physics地球物理勘探：geo-physical exploration.测井：logging电测井作业：wireline logging operation 泥浆测井：mud logging井（副词“好”含意）：well拓展记忆：井眼：bore hole油气井：oil&gas well试井：well test井下：down-hole井下作业：down-hole operation。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
行业英语之实用词汇
现场实用词汇短语
一、甲方乙方
1. 承包商人员 ( Contractor’s Personnel )
Equipment Supervisor 设备总监
Materials Supervisor 材料总监
Senior Toolpusher 高级队长
Junior Toolpusher 值班队长
Driller 司钻
Sub Sea Engineer (SSE) 水下工程师
Assistant Driller (AD) 副司钻
Derrick Man 井架工
Floor Man (roughneck) 钻工
Crane Operator 吊车工
Mechanic 机械师
Electrician 电气师
Repairman 修理工
Welder 焊工
Radio Operator 电报员
Warehouse Man (stock Keeper) 材料员
Medic 医生
Safety Supervisor 安全监督
Interpreter (translator) 翻译
Chief Steward 管事
Cook 厨师
2、作业者及服务公司人员
( Operator’s Personnel and Service Company Personnel)
Drilling Superintendent 钻井监督
Company Man (Operator’s Representative) 公司代表
Geologist 地质师
Mud Logging Engineer (Mud logger) 泥浆录井工程师
Sample Catcher 捞砂工
Mud Engineer 泥浆工程师
ROV Engineer 潜水工程师
Cementer 固井工
Cement Engineer 固井工程师
Testing Engineer 试油工程师
Coring Engineer 取芯工程师
Wireline Logging Engineer电测工程师
二、主要设备
1.钻井设备 (Drilling Equipment):
Drawworks 钻井绞车
Rotary Table 转盘
Bushing 补心
Top Drive System (TDS) 顶驱
Swivel 水龙头
Crown Block 天车
Traveling Block 游车
Hook 大钩
Derrick 井架
Pipe Spinning Wrench 钻杆气动扳手
Ezy-Torq 液压猫头
Elmagco Brake 涡磁刹车
Pipe handling Equipment 钻杆移动设备
Iron roughneck 铁钻工
Pipe Racking System 钻杆排放系统
Drill String 钻柱
Drilling Sub 钻井短节
Fishing Tool 打捞工具
Power Tong 动力大钳
Air Winch (air tugger) 气动绞车
Crown-O-Matic (Crown Saver) 防碰天车
2. 泥浆系统 (Mud System)
Mud Pump 泥浆泵
Shale shaker 振动筛
Mud Cleaner 泥浆清洁器
Desilter 除泥器
Desander 除砂器
Degasser 除气器
Centrifuge 离心机
Mud Agitator 泥浆搅拌器
Mud Mixing System 泥浆混合系统
Centrifugal Pump 离心泵
Standpipe Manifold 立管管汇
Rotary Hose 水龙带
Bulk Air System and Tank 吹灰系统和灰罐
3. 井控设备 (Well Control Equipment):
Ram Type Preventor 闸板防喷器
Annular Type Preventor 万能防喷器
BOP Stack 防喷器组
Gate Valve 闸阀
Choke and Kill Manifold 阻流压井管汇
Remotely Operated Panel 远程控制面板
Choke Control Panel 阻流控制面板
BOP Handling Equipment 防喷器搬运设备
Diverter 转喷器
五. 机房(Engine Room)
Diesel Engine 柴油机
Emergency Generator 应急发电机
Water Maker (desalinization unit) 造淡机
Air Compressor 空气压缩机
Boiler 锅炉
Air-conditioning System 空调系统
Piping System 管汇系统
Generator 发电机
Transformer 变压器
DC Motor 直流马达
AC Motor 交流马达
4. 安全设备 (Safety Equipment) Fire Control System 消防控制系统
Fire Detection System 火情探测系统
Fixed Fire Extinguishing System 固定消防系统Portable Extinguisher 移动灭火器
Fire-Fight Equipment 消防设备
Foam System 泡沫系统
Escape Routes 逃生路线
Breathing Apparatus 呼吸器
Gas Detection System 气体探测系统
Helicopter Facility 直升机设施
Sick-Bay (Hospital) 医务室
Pollution Control 防污控制
5. 其他 ( Others)
Cementing Unit 固井装置
Well Testing Equipment 试油设备
Mud Logging Unit 泥浆录井房
Wire Logging Unit 电测装置
ROV 潜水器
Meter 米
Foot 英尺
Inch 英寸
Day (night) Shift 白(夜)班
Crew Change 倒班
Position 岗位
Penetration (桩腿插桩)入泥
Evacuation 撤离
Rig (Drilling rig) 钻机, 钻井船
Quarters (living quarters, accommodation area) 生活区Drill Floor (Rig floor) 钻台
Bridge (Pilot house, Steerwheel house) 驾驶室Control Room 控制室
Helideck 直升机甲板
Cementing Unit Room 固井泵房
Air Compressor Room 空气压缩机房
BOP Control Room BOP控制房
Radio Room 报房
Engine Room 机房
Warehouse (Store) 材料库房
Paint Room (paint locker) 油漆房库
Mud pit 泥浆池
Pipe Rack Area 钻杆排放区
Pipe Slide 滑道
Ramp 坡道
Pump Room 泵房
Shale Shaker House 振动筛房Coffee Room 咖啡室
Mess (dining) Room 餐厅Recreation Room 娱乐房
TV Room
Change Room 工衣房Kitchen 厨房
三、钻具,井口工具,打捞工具Drill Pipe 钻杆
Drill Collar 钻铤
Heavy Weight Drill Pipe 加重钻杆
Elevator 吊卡
Tong 大钳
Make-up Tong 上扣大钳
Break-out Tong 卸扣大钳
Mud Box 泥浆防喷盒
Casing Stabbing Board 套管扶正器
Slips 卡瓦
Spider 卡盘
Mouse Hole 小鼠洞(接单根用)
Kelly Spinner 方钻杆旋转器
Kelly Cock 方钻杆阀
Chain Tong 链钳
Casing 套管
Tubing 油管
Drill String 钻柱
Jar (drilling jar) 震击器
Right Hand Thread 正扣
Left Hand Thread 反扣。