冷藏柜设备操作说明书
海尔 FCD-515HA 515升冷藏冷冻柜 使用说明书
器具周围或在嵌入式结构里无阻碍物，保持通风通畅。
如果电压波动范围较大(超过187V~242V），有可能造成冷柜无法启动、温控器或压缩机损毁，或者有异常噪声。
这时候，需要加装1000W以上的自动稳压器配合使用。
·在任何情况下，请保证所使用的插座连接了接 地线，并且切勿改造电源线和插头。
·电源线插头应保持与插座牢固接触，否则可能导致火灾。
·冷柜安装就位后,插头应在容易被够到的地方，以保证发生意外时可以及时拔下冷柜插头。
·切勿以拉扯电源线的方法拔出冷柜的插头。
一定要握住插头，然后从插座中拔出。
·切勿让箱体压住电源线或人为踩踏电源线。
·搬运冷柜时，请小心谨慎，将电源线捆扎起来，切勿滚压电源线。
·如果电源软线损坏，为了避免危险，必须由 制造商、其维修部或类似部门的专业人员更换。
·如果电源线需要加长，加长线的截面面积不得小于0.75m㎡。
冷柜开始运行后，切勿用手触摸内胆制冷表面，尤其是手湿的时候，否则，皮肤可能会粘在内胆表面上，造成伤害。
·不得损坏制冷回路。
严禁私自拆卸、改造冷柜。
·维修冷柜必须由具有专业资格的人员来进行。
严禁私自改造冷柜本机使用交流220V/50Hz电源使用三孔插座（接地）切勿损坏电源线当电源线损坏时当有煤气等易燃气体泄露时小心冻伤冷柜废弃不用时应先关闭气体泄漏的阀门，然后打开门窗、通风排气；切勿插拔冷柜电源插头。
请使冷柜远离火源，以防意外。
并且请将冷柜门卸掉，以免儿童进入玩耍而发生意外。
并将冷柜送到指定处理地点进行妥善处理或交由专业人员处理，不应随意丢弃，以避免对环境造成危害或引发其他危险。
·家庭旅馆型环境；·农场以及宾馆、汽车旅店和居住型环境的顾客；·防止儿童进入冷柜内部玩耍，钥匙妥善保管。
·防止儿童将手、脚等伸入冷柜机仓、后背等金属防 护部件的各种冲孔、边缝处，以免对身体造成意外 伤害。
平台式冷藏柜 冷冻柜 使用说明书
5. 废弃处理............................................................................................................................................6
为达到最佳性能：
* 请勿将冷藏柜/冷冻柜摆放在炉子、烤架或其它会产 生高温的设备附近。
* 摆放位置应坚实，足以承受设备重量。
* 应避免将本机安装在不允许滴水的场所。采用并排 或背靠背安装方式(可能是与其它厂商的产品一起安 装)时，由于两台机器之间可能会出现冷凝，从而导 致冷凝水滴落到地板上。
* 请勿将本机暴露在直射阳光或高温下。
6. 电气连接 ...........................................................................................................................................2
7. 排水管连接 ........................................................................................................................................2
[a] 显示故障代码的故障....................................................................................................................6
[b] 不显示故障代码的故障................................................................................................................6
雅绅宝冷柜按键说明
雅绅宝冷柜按键说明雅绅宝冷柜按键说明1. 引言雅绅宝冷柜是一款高品质的冷藏设备，配备了多功能按键，方便用户进行各种操作。
本文将对雅绅宝冷柜的按键功能进行详细说明，以帮助用户更好地使用和了解该产品。
2. 功能按键一览以下是雅绅宝冷柜各个按键的功能列表：•电源按键：用于打开和关闭冷柜的电源。
•温度调节按键：用于调节冷柜的工作温度。
通常有上升和下降两个箭头按钮，用户可以通过按下箭头按钮来提高或降低温度。
•模式切换按键：用于切换冷柜的工作模式。
不同的模式可以满足不同的使用需求，例如：冷藏模式、冷冻模式等。
•快速冷冻按键：按下该按键可以快速降低冷藏室的温度，加快冷冻速度。
•冷藏室照明按键：用于控制冷藏室的灯光，按下该按键可以开启或关闭照明。
•制冰按键：用于开启或关闭冷柜内部的制冰功能。
•解冻按键：按下该按键可以启动冷柜的解冻程序，将冷藏室内的冰层融化并排出。
3. 操作步骤以下是使用雅绅宝冷柜按键的一般操作步骤：1.打开冷柜的电源开关，通常位于冷柜的侧面或背面。
2.使用温度调节按键设置所需的工作温度。
根据个人需求，按下上升或下降箭头按钮进行温度调整。
3.根据需要选择合适的模式，按下模式切换按键进行模式设置。
4.如果需要快速冷冻，按下快速冷冻按键。
5.控制冷藏室照明按键来改变照明状态。
6.如果需要制冰，按下制冰按键启动制冰功能。
7.想要解冻冷藏室，按下解冻按键启动解冻程序。
8.使用完毕后，按下电源按键关闭冷柜的电源。
4. 注意事项在操作雅绅宝冷柜时，请注意以下事项：•请按照实际需要调整冷柜的温度，不要将温度设置得过低或过高，以保证食品的质量和安全。
•在切换模式或按下其他功能按键时，请耐心等待冷柜完成相应的操作，不要频繁按动按键。
•在进行解冻操作时，注意冷藏室内可能产生的水分，及时清理以免积水。
•如果有其他疑问或需要进一步了解冷柜的使用方法，请参考产品说明书或联系售后服务中心。
以上是对雅绅宝冷柜按键功能的详细说明，希望能够帮助用户更好地使用这款优质的冷藏设备。
海尔冷柜说明书
商用冷藏柜/冷冻柜COMMERCIAL REFRIGERATOR/FREEZER使用说明书INSTRUCTION MANUALHRE/HFE-127MA-_HD●使用说明书是本产品不可分割的重要组成部分，用户须妥善保管。
●请务必仔细阅读本使用说明书中描述的指南和警告事项，因为这些指南和警告事项为安装人员/用户提供了正确安装、持续安全地使用和保养本产品所需的重要信息。
●请妥善保管本使用说明书，以便必要时参考使用。
● This booklet is an integral and essential part of the product and should be kept and preserved by the user.● Please read carefully the guidelines and warnings contained herein as they are intended to provide the installer/user with essential information for the proper installation and the continued safe use and maintenance of the product.● Please preserve this booklet for any further consultation that may be necessary.生产商： 星崎电机(苏州)有限公司中文I. 安装说明 (1)1. 各部分名称(HRE-127MA-CHD) (1)2. 附件 (1)3. 位置 (1)4. 安装方法 (2)5. 层板和导轨 (3)[a] 层板和层板托(标准) (3)[b] 导轨(定制) (4)[c] 支撑杆(定制) (4)6. 电气连接 (4)7. 排水管连接 (4)II. 操作说明 (5)1. 启动 (5)2. 前板 (5)3. 柜内温度设定 (6)4. 除霜方式 (7)5. 指示灯 (7)6. 关机 (8)III. 保养 (8)1. 内部、外部、层板 (8)2. 空气过滤网 (8)3. 报修前 (9)[a] 显示故障代码的故障 (9)[b] 不显示故障代码的故障 (9)4. 废弃处理 (9)5. 保修 (9)ENGLISH I.INSTRUCTIONS (10)INSTALLATION (10)(HRE-127MA-CHD)CONSTRUCTION1. (10)ACCESSORIES2. (10)LOCATION3. (11)UPSET4.5. SHELF AND RAIL (12)[a] SHELF AND SHELF CLIP (standard) (12)(customized) (13)RAIL[b] (13)(customized)[c]HANGER6. ELECTRICAL CONNECTIONS (13) (13)7.CONNECTIONSDRAININSTRUCTIONS (14)OPERATINGII. (15)UP1.START (15)PANEL2.FRONT3. CABINET TEMPERATURE SETTING (15) (17)DEFROST4. (17)LIGHTS5.INDICATOR (17)DOWN6.SHUT (18)III.MAINTENANCE1. INTERIOR, EXTERIOR, SHELF (18) (18)2.FILTERAIR3. BEFORE CALLING A SERVICE AGENT (19)[a] TROUBLES WITH ERROR CODE INDICATION (19)[b] TROUBLES WITHOUT ERROR CODE INDICATION (19)4. (19)DISPOSAL (20)5.WARRANTY中文警告请勿弄湿本产品或在潮湿环境下使用本产品。
凯雪猪肉冷藏展示柜使用说明
凯雪猪肉冷藏展示柜使用说明
如果是机械式控温冰箱，直接调节温度旋钮就可以了。
温控器上的档位1档温度最高，7档温度最低。
冰柜夏天可以打到1档或2档，冬天打到4档或5档。
2、另外，当环境温度低于10度，要打开温度补偿开关；温度超过15度时，关闭此开关。
3、电脑控温的冰箱，通常只需要设置为自动模式，或者智能模式就可以了，如果需要单独设置温度，可以先选择温度，再点击设置（参考说明书），调整数字到合适大小即可。
4、识别按键冷藏展示柜温控器上面的按键一般5个，分别是：set键、power键、上键、下键、化霜键。
set键：即设置键；power 键：冷藏展示柜的电源开关键；下键、上键：在设置菜单中使用的温度设置按钮；化霜键：给冷藏展示柜手动化霜，冷藏展示柜大多具备自动化霜功能，按此键可进行手动强制化霜。
冷藏柜操作说明
冷藏柜操作说明一、冷藏柜概述冷藏柜是一种用于存储和保鲜食物的设备。
本操作说明将为您提供使用冷藏柜的详细步骤和注意事项，以确保您能正确地操作和维护冷藏柜，延长其使用寿命。
二、冷藏柜操作步骤1. 接通电源将冷藏柜的电源线插入电源插座，确保电源供应正常。
2. 控制面板设置冷藏柜的控制面板通常位于柜体上方或侧面，具体位置请参照您所使用冷藏柜的说明书。
按照以下步骤设置控制面板：a. 打开控制面板上的电源开关。
b. 根据需要，设置冷藏温度。
通常可以通过上下箭头键或旋钮进行调节，选择适宜的温度。
c. 如果冷藏柜提供了特殊功能，如快速冷冻或快速降温等，可根据使用要求进行设置。
d. 确保所需温度和功能设置完成后，关闭控制面板的电源开关。
3. 存储食物a. 打开冷藏柜的门。
b. 根据您的需要和食物种类，合理摆放食物。
注意不要将食物放置太过拥挤，以确保空气流通，并避免食物的过早腐败。
c. 如果冷藏柜提供了可调节的货架，可以按照需要进行调整，以适应不同尺寸和类型的食物。
d. 注意将易腐食物放置在较低的温度区域，以延长其保鲜期。
4. 定期清洁冷藏柜容易积累污垢和冰渍，定期清洁可以保持其卫生和正常运行。
注意以下步骤：a. 断开冷藏柜的电源插头，确保安全。
b. 使用柔软的湿布或海绵，加入适量中性洗涤剂清洁冷藏柜内外表面。
c. 清洁过程中避免水流进入控制面板或电器部件。
d. 使用干净的湿布将清洁剂残留物清洗干净。
e. 干燥后，重新连接电源插头。
5. 警告和注意事项a. 请勿将冷藏柜用于非指定用途。
b. 不要将已经过期或有异味的食物放入冷藏柜。
c. 避免长时间敞开冷藏柜的门，以保持内部温度稳定。
d. 冷藏柜不宜放置过重的物品，以免损坏货架或造成意外伤害。
e. 在清洁冷藏柜时，务必遵循相关操作规定，确保安全和有效。
三、维护保养建议1. 定期检查冷藏柜的电源线和插头，避免因损坏导致电器故障或安全事故。
2. 如发现冷藏柜运行异常，出现异常噪音或温度无法达到设定值，请及时联系维修人员进行检修。
新飞BCD-191W说明书
新飞BCD-191W说明书一、安全操作1.请仔细阅读并理解本操作说明书，并按照说明书的操作步骤进行操作。
2.在使用之前，请确保电源线和插座之间的连接牢固，以避免电源线松动或者插头生锈的情况。
3.使用电器时，请保持干燥，避免电器进水。
4.请将电器放在通风良好的位置，避免过热。
二、产品概述三、产品特点1.多功能显示屏：新飞BCD-191W配备了一块多功能显示屏，可以显示温度、湿度、定时及定量等多种信息。
2.保鲜效果好：该产品内部采用优质冷藏技术，能够使食物保持新鲜和味道。
3.节能环保：新飞BCD-191W采用环保制冷技术，具有低能耗、低噪音等特点。
4.大容量设计：产品容量达到191升，可以容纳大量食品和饮料。
四、使用方法1.食品和饮料放置：首先，将要冷藏的食品和饮料按照大小和顺序放置在产品内部。
2.温度设置：通过多功能显示屏操作键，可以设置冷藏柜的温度。
根据需要，可以选择适当的温度。
3.定时功能：通过多功能显示屏操作键，可以设置冷藏柜的定时时间。
设定的时间到达后，冷藏柜会自动关闭。
4.湿度调节：通过多功能显示屏操作键，可以设置冷藏柜的湿度。
根据需要，可以选择适当的湿度。
五、维护与保养1.定期清洁：产品使用一段时间后，应定期清洗冷藏柜的内部和外部。
使用柔软的布和温和的洗洁剂可以擦拭产品表面。
2.维护冷藏效果：产品使用时，应避免频繁开关冷藏柜的门，以免导致冷气流失，影响保鲜效果。
六、常见故障与排除方法1.无法启动冷藏柜：请检查电源插座是否正常连接，以及插头是否生锈。
七、注意事项1.在清洗或维修冷藏柜时，请先拔掉电源线，以免意外触电。
2.请勿将手或其他物品伸入冷藏柜内部，以避免危险。
3.请勿在电器上放置过重物品，以免损坏冷藏柜。
4.使用本产品时，请确保儿童远离电器，以避免意外伤害。
八、售后服务。
莹雪保鲜柜说明书
莹雪保鲜柜说明书
1、冷藏保鲜柜应放在平坦地面上，放置保鲜柜的室内环境应通风良好、干燥、顶部离天花板在50cm以上，左右两侧离其他物件20cm 以上，背后离其他物件20cm以上。
2、放置好的冷藏保鲜柜应该静置2-3小时，然后再启用，而且好在使用前，对保鲜柜行3-7小时空箱通电运行，这样有利于机身的后续运行。
保鲜柜停机后亦不可立即启动，需等待几分钟，以免烧坏压缩机。
3、往冷藏保鲜柜里放置货品时要尽量的放均匀，食品之间应隔开适当的间隙，且不可次放入过多。
这样不仅可以保证货品受温均衡，质量保证，而且对于长时间使用的保鲜柜，其层板也不会因受力不同造成变形。
4、温控器从（1~7）或是从小到温度逐渐变冷，用户可以根据储存食品的种类不同，相应的调节温控器的档位，以达到保鲜和冷冻食品的目的。
5、尽量减少保鲜柜开门次数和时间。
热的食品应让其自然冷却到室温后，再放入保鲜柜。
水分较多食品，应洗净沥干后，用塑料袋包好放入保鲜柜，以免水分蒸发加厚霜层，影响保鲜柜制冷效果，增加耗电量。
盛世冰峰商用冷柜使用说明书
盛世冰峰商用冷柜使用说明书一、产品概述盛世冰峰商用冷柜是一款高效、可靠的商用冷藏设备，广泛应用于超市、餐饮店、酒店等场所。
本说明书将详细介绍冷柜的使用方法、注意事项以及常见故障处理方法，帮助用户正确使用和维护冷柜，确保其正常运行。
二、产品特点1. 制冷效果优异：盛世冰峰商用冷柜采用先进的制冷技术，能够快速降温并保持恒定的低温状态，确保食品的新鲜度和安全性。
2. 多功能设计：冷柜内部空间合理设计，可根据不同需求进行灵活调整，适用于存放各类食品和饮料。
3. 节能环保：冷柜采用高效节能制冷系统，具有良好的节能性能和环保特点，有效降低使用成本。
4. 操作简便：冷柜配备智能控制面板，用户可轻松设置温度、湿度等参数，实现自动化控制，操作方便快捷。
三、使用方法1. 安装：在使用冷柜之前，请确保安装地面平整稳固，避免震动和摇晃。
将冷柜放置在通风良好的位置，保持与周围物体的距离，以确保散热效果。
同时，务必保持冷柜周围的清洁，避免灰尘和杂物进入机器内部。
2. 电源接通：将冷柜插头插入电源插座，并确保电源线路正常。
接通电源后，冷柜将开始运行，此时可以设置所需的温度和湿度等参数。
3. 放置食品：打开冷柜门，将需要存放的食品整齐摆放在冷柜内部，避免食品之间的相互挤压和堆积，以免影响冷却效果。
同时，冷柜内部的温度分布不均匀，较低的温度区域适合存放易变质的食品，而较高的温度区域适合存放耐冷食品。
4. 温度设置：根据食品的需要，使用冷柜面板上的温度设置功能，将冷柜的温度调整到合适的范围。
在设置温度时，应注意不要将温度调得过低，以免造成冷柜过度耗能或食品冻结。
5. 定期除霜：冷柜在使用一段时间后，可能会产生霜冻，影响制冷效果。
建议定期进行除霜操作，可通过冷柜面板上的除霜功能来实现。
在除霜过程中，应将冷柜内的食品取出，并使用干净的毛巾或吸水纸将冷柜内的水分擦拭干净，以免产生异味或滋生细菌。
6. 清洁和维护：定期清洁冷柜内部和外部的污垢，可以使用中性洗涤剂和湿布进行擦拭。
全景冷藏展示柜操作手册说明书
10/30/2006 PP MNL0603OPERATOR’S MANUALThis manual provides information on installation, operating, maintenance, trouble shooting & replacement parts forFULL VIEW DROP-IN REFRIGERATED DISPLAY CASE44250DIMA 44262DIMA 44274DIMA 44250DIP A 44262DIP A 44274DIP A 44250DISA 44262DISA 44274DISANOTIFY CARIER OF DAMAGE AT ONCE.It is the responsibility of the consignee to inspect the container upon receipt of same and to determine the possibility of any damage, including concealed damage. Randell suggests that if you are suspicious of damage to make a notation on the delivery receipt. It will be the responsibility of the consignee to file a claim with the carrier. We recommend that you do so at once.Information contained in this document is known to be current and accurate at the time of printing/ creation. Unified Brands recommends referencing our product line websites, , for the most updated product information and specifications.1055 Mendell Davis Drive, Jackson MS 39272 888-994-7636 • Fax 888-864-7636 • page 2………………………………….…………Congratulationspage 3……………………………………Parts & Service Hotlinepage 3………………………………...…Serial Number Locationpage 4-6……………………………….Randell Limited Warrantypage 7…………………………………………Unit Specificationspage 8-9…....……………………………..……...Unit Installationpage 10………………………………………Electrical Diagramspage 11…….……………………………………...Unit Operationpage 12-13……………………..………Preventive Maintenancepage 14-15..………………………………..……Troubleshootingpage 16-17…………………………….……..Replacement PartsCongratulations on your recent purchase of Randell food service equipment,and welcome to the growing family of satisfied Randell customers.Our reputation for superior products is the result of consistent qualitycraftsmanship. From the earliest stages of product design to successive stepsin fabrication and assembly, rigid standards of excellence are maintained byout staff of designers, engineers, and skilled employees.Only the finest heavy-duty materials and parts are used in the production ofRandell brand equipment. This means that each unit, given propermaintenance will provide years of trouble free service to its owner.2 800-621-8560NOTICE:Due to a continuous program of product improvement, Randell reserves the right to make changes in design and specifications without prior notice.NOTICE: Please read the entire manual carefully before installation. If certain recommended procedures are not followed, warranty claims will be denied.MODEL NUMBER _________________________SERIAL NUMBER _________________________INSTALLATION DATE _____________________The serial number is located on the interior left side of the refrigerated case. 800-621-8560 3Congratulations on your purchase of a Randell piece of equipment. Randell believes strongly in the products it builds and backs them with the best warranty in the industry. Standard with every unit comes the peace of mind that this unit has been thoroughly engineered, properly tested and manufactured to excruciating tolerances, by a manufacturer with over 30 years of industry presence. On top of that front end commitment, Randell has a dedicated staff of certified technicians that monitor our own technical service hotline at 1-800-621-8560 to assist you with any questions or concerns that may arise after delivery of your new Randell equipment.PARTS WARRANTY1. One year parts replacement of any and all parts that are found defective in material or workmanship. Randell warrants all component parts of manufactured new equipment to be free of defects in material or workmanship, and that the equipment meets or exceeds reasonable industry standards of performance for a period of one year from the date of shipment from any Randell factory, assembly plant or warehouse facility.NOTE: Warranties are effective from date of shipment, with a thirty day window to allow for shipment, installation and set-up. In the event equipment was shipped to a site other than the final installation site, Randell will warranty for a period of three months following installation, with proof of starting date, up to a maximum of fifteen months from the date of purchase.2. Free ground freight of customer specified location for all in warranty parts within continental U.S. Component part warranty does not cover glass breakage or gasket replacement. Randell covers all shipping cost related to component part warranty sent at regular ground rates (UPS, USPS). Freight or postage incurred for any express or specialty methods of shipping are the responsibility of the customer.LABOR COVERAGEIn the unlikely event a Randell unit fails due to defects in materials or workmanship within the first ninety days, Randell agrees to pay the contracted labor rate performed by an Authorized Service Agent (ASA). Any work performed by a non-ASA will not be honored by Randell. Please consult Randell Technical Support (800-621-8560) for a complete listing of ASAs. Warranties are effective from date of shipment, with a thirty day window to allow for shipment, installation and setup. Where equipment is shipped to any site other than final installation, Randell will honor the labor warranty for a period of ninety days following installation with proof of starting date, up to a maximum of six months from date of purchase.4 800-621-8560Temperature adjustments are not covered under warranty, due to the widerange of ambient conditions.To request a warranty approval number, call our Field Service Department at: 1-800-621-8560WHEN OPTIONAL 5 YEAR COMPRESSOR WARRANTY APPLIES1. Provide reimbursement to an ASA for the cost of locally obtainedreplacement compressor in exchange for the return of the defectivecompressor sent back freight prepaid. Note: Randell does limitamount of reimbursement allowed and does require bill from localsupply house where compressor was obtained (customer should notpay servicing agent up front for compressor).2. Provide repair at the manufacturing facility by requiring that thedefective unit be sent back to Randell freight prepaid. Perform repair atthe expense of Randell and ship the item back to the customer freightcollect.3. Furnish complete condensing unit freight collect in exchange for thereturn of the defective compressor sent back freight prepaid.(Decisions on whether or not to send complete condensing units will bemade by Randell’s in-house service technician).WHEN OPTIONAL LABOR EXTENSION POLICY APPLIESRandell will provide reimbursement of labor invoiced to any customer that hasan optional labor extension of our standard warranty. (Reasonable geographicand industry rates do apply) Randell offers both 1 and 2 year extensions.Labor extensions begin at the end of our standard warranty and extend out 9months to 1 calendar year or 21 months to 2 calendar years from date of purchase. Please contact Randell’s technical service hotline at 1-800-621-8560 for details and warranty authorization numbers.WHEN EXPORT WARRANTIES APPLY1. Randell covers all non-electrical components under the sameguidelines as our standard domestic policy.2. All electrical components operated on 60 cycle power are coveredunder our standard domestic policy.3. All electrical components operated on 50 cycle power are covered for90 days from shipment only.4. Extended warranty options are not available from the factory.ITEMS NOT COVERED UNDER WARRANTY1. Maintenance type of repairs such as condenser cleaning, temperatureadjustments, clogged drains and unit leveling.2. Randell does not cover gaskets under warranty. Gaskets are amaintenance type component that are subject to daily wear and tearand are the responsibility of the owner of the equipment. Because ofthe unlimited number of customer related circumstances that can causegasket failure all gasket replacement issues are considered non-warranty. Randell recommends thorough cleaning of gaskets on aweekly basis with a mild dish soap and warm water. With proper careRandell gaskets can last up to two years, at which time we recommend 5replacement of all gaskets on the equipment for the best possibleperformance.NOTICE: FOOD LOSS IS NOT COVERED UNDER WARRANTY3. Repairs caused by abuse such as broken glass, freight damage, orscratches and dents.4. Electrical component failure due to water damage from cleaningprocedures.DAMAGESAll crating conforms to general motor carrier specifications. To avoid concealed damage, we recommend inspection of every carton upon receipt. In the event the item shows rough handling or visible damage to minimize liability, a full inspection is necessary upon arrival. Appearance of damage will require removing the crate in the presence of the driver. A notation must be placed on the freight bill and signed for by the truck driver at the time of delivery. Any and all freight damage that occurs to a Randell piece of equipment as a result of carrier handling is not considered under warranty, and is not covered under warranty guidelines. Any freight damage incurred during shipping needs to have a freight claim filed by the receiver with the shipping carrier. Consignee is responsible for filing of freight claims when a clear delivery receipt is signed. Claims for damages must be filed immediately (within 10 days) by the consignee with the freight carrier and all cartons and merchandise must be retained for inspection.RETURNED GOODSAuthorization for return must first be obtained from Randell before returning any merchandise. Any returned goods shipment lacking the return authorization number will be refused, all additional freight costs to be borne by the returning party. Returned equipment must be shipped in original carton, freight prepaid and received in good conditions. Any returned merchandise is subject to a minimum handling charge (consult factory for rate). INSTALLATIONEquipment installation is the responsibility of the dealer and/or their customer. Randell requires all equipment to be professionally installed.*FOOTNOTES IN REFERENCE TO PARAGRAPHS ABOVE1. Herein called Randell.2. NET means list price less discount, warranty, labor policy, freight, Randell delivery and other miscellaneous charges.CASH DISCOUNTS WILL BE CALCULATED ON NET ONLY.6 800-621-8560 744250DIMA shown* 44” is the height of the unit above counter top. Overall height including the compressor housing is 62”.Model L D H StyleCapacityCu. Ft. H.P. Volts Amp NEMA 44250DIMA 50" 25.25" 44"* Single Service, Mirrored Back 20.1 3/8 115/60/1 6.5 5-15P 44262DIMA 62” 25.25” 44”* Single Service, Mirrored Back 25.5 1/2 115/60/1 8.8 5-15P 44274DIMA 74” 25.25” 44”* Single Service, Mirrored Back 31.1 1/2 115/60/1 8.8 5-15P 44250DIPA 50” 26.5” 44”* Double Service, Pass-Thru20.1 3/8 115/60/1 6.5 5-15P 44262DIPA 62” 26.5” 44”* Double Service, Pass-Thru25.5 1/2 115/60/1 8.8 5-15P 44274DIPA 74” 26.5” 44”* Double Service, Pass-Thru31.1 1/2 115/60/1 8.8 5-15P 44250DISA 50” 25.25” 44”* Single Service, See-Thru20.1 3/8 115/60/1 6.5 5-15P 44262DISA 62” 25.25” 44”* Single Service, See-Thru25.5 1/2 115/60/1 8.8 5-15P 44274DISA74"25.25"44"*Single Service, See-Thru31.11/2115/60/18.85-15PSELECTING A LOCATION FOR YOUR NEW UNITThe following conditions should be considered when selecting a location for your unit:1. Floor and Countertop Load:The area on which the unit will restmust be level, free of vibration, and suitably strong enough to supportthe combined weights of the unit plus the maximum product loadweight.NOTE: If there is a question pertaining to weight load limits, consult thefactory at 1-800-621-8560.2. Clearance: There must be a combined total of at least 3” clearance onall sides of the unit.3. Ventilation:The air cooled self contained unit requires a sufficientamount of cool clean air. Ensure the cabinet holding the drop-indisplay case is properly vented. Avoid surrounding your display casearound other heat generating equipment and out of direct sunlight.Also, avoid locating in an unheated room or where the roomtemperature may drop below 55° F (13°C) or about 90° F (32°C). INSTALLATION CHECKLISTAfter the final location has been determined, refer to the following checklist prior to start-up:1. Check all exposed refrigeration lines to ensure that they are not kinked,dented, or rubbing together.2. Check that the condenser and evaporator fans rotate freely withoutstriking any stationary members.3. Plug in unit and turn on main on/off power switch.4. Allow unit time to cool down to temperature. If temperatureadjustments are required, the temperature control can be accessedthrough the hole on top of the unit.5. Refer to the front of this manual for serial number location. Pleaserecord this information in your manual on page 3 now. It will benecessary when ordering replacement parts or requesting warrantyservice.6. Confirm that the unit is holding temperature. Set controls to desiredtemperature for your particular ambient and altitude.7. Allow your unit to operate for approximately 2 hours before putting infood to allow interior of unit to cool down to storage temperature.NOTE: All motors are oiled and sealed.NOTE: FAILURE TO FOLLOW INSTALLATION GUIDELINES AND RECOMMENDATIONS MAY VOID THE WARRANTY ON YOUR UNIT.ELECTRICAL SUPPLY: The wiring should be done by a qualified electrician in accordance with local electrical codes. A properly wired and grounded outlet will assure proper operation. Please consult the data tag attached to the compressor to ascertain the correct electrical requirements. Supply voltage and amperage8 800-621-8560requirements are located on the serial number tag located inside the mechanical housing.NOTE: It is important that a voltage reading be made at the compressor motor electrical connections, while the unit is in operation to verify the correct voltage required by the compressor is being supplied. Low or high voltage can detrimentally affect operation and thereby void its warranty. NOTE: it is important that your unit has its own dedicated line. Condensing units are designed to operate with a voltage fluctuation of plus or minus 10% of the voltage indicated on the unit data tag. Burn out of a condensing unit due to exceeding voltage limits will void the warranty. 910 800-621-8560Randell has attempted to preset the cold controls to ensure that your unit runs at an optimum temperature, but due to varying ambient conditions, including elevation, food product as well as type of operation, you may need to alter this temperature.It is strongly recommended that the doors be kept closed when the unit is not in use and between rush periods. This is especially important in the summer and in kitchens exceeding 80° F. Do not leave the doors open for prolonged periods of time. Close after using.NOTE: Even though your drop-in display case was designed for heavy use, excessive door openings should be avoided in order to maintain proper cabinet temperature and eliminate the possibility of coil freeze-up.Your drop-in display case was equipped with a temperature adjustment control located within the cabinet on the front face of the evaporator coil.To adjust the temperature in refrigerated units:A. To lower the temperature:1. Turn the dial knob clockwise.2. There are numbers to indicate settings. Keep the arrow on theknob pointed within the numbered section of the arc.3. Turning it clockwise beyond the numbered section can result infreeze-up.B. To raise the temperature:1. Turn the dial knob counterclockwise.2. There are numbers to indicate settings. Keep the arrow on theknob pointed within the numbered section of the arc.3. Turning it counterclockwise beyond the numbered section willshut the compressor off.NOTE: It is not recommended to turn the dial above 8 or below 1 on the temperature control. If the adjustments still do not resultin proper temperature please contact the factory at 1-800-621-8560.C. If your temperature control is at the maximum setting and the cabinettemperature still remains too low or too high, you may need to adjust the pressure control if your display case is equipped with one.1. Turn the right adjustment screw clockwise (1/4 turn at a time) toa lower number for a colder temperature.2. Turn the right adjustment screw counterclockwise (1/4 turn at atime) to a higher number for a warmer temperature.NOTE: Numbers on pressure control are pounds of pressure, not degrees F.NOTE: Do not adjust the differential screw.Randell strongly suggests a preventive maintenance program which would include the following Monthly procedures:1. Cleaning of all condenser coils. Condenser coils are a critical component in the life of the compressor and must remain clean to assure proper air flow and heat transfer. Failure to maintain this heat transfer will affect unit performance and eventually destroy the compressor. Clean the condenser coils with coil cleaner and/or a vacuum, cleaner and brush.NOTE: Brush coil in direction of fins, normally vertically as to not damage or restrict air from passing through condenser.2. Clean fan blade on the condensing unit.3. Clean and disinfect drains with a solution of warm water.4. Clean and disinfect drain lines and evaporator pan with a solution of warm water.5. Clean all gaskets on a weekly if not daily basis with a solution of warm water and a mild detergent to extend gasket life.NOTE: DO NOT USE SHARP UTENSILS.RECOMMENDED CLEANERS FOR YOUR STAINLESS STEEL INCLUDE THE FOLLOWING:JOB CLEANING AGENT COMMENTSRoutine cleaning Soap, ammonia, detergentMedallionApply with a sponge or clothFingerprints and smears Arcal 20, Lac-O-Nu,EcoshineProvides a barrier filmStubborn stains and discoloration Cameo, Talc, Zud, FirstImpressionRub in the direction of thepolish linesGreasy and fatty acids, blood, burnt-on foods Easy-Off, Degrease It, OvenAidExcellent removal on allfinishesGrease and Oil Any good commercialdetergentApply with a sponge or clothRestoration/Preservation Benefit, Super Sheen Good idea monthlyReference: Nickel Development Institute, Diversey Lever, Savin, Ecolab, NAFEM. NOTE: Do not use steel pads, wire brushes, scrapers, or chloride cleaners to clean your stainless steel. CAUTION: DO NOT USE ABRASIVE CLEANING SOLVENTS, AND NEVER USE HYDROCHLORIC ACID (MURIATIC ACID) ON STAINLESS STEEL.NOTE: Do not pressure wash equipment as damage to electrical components may result.Proper maintenance of equipment is the ultimate necessity in preventing costly repairs. By evaluating each unit on a regular schedule, you can often catch and repair minor problems before they completely disable the unit and become burdensome on your entire operation.For more information on preventive maintenance, consult your local service company or CFESA member. Most repair companies offer this service at very reasonable rates to allow you the time you need to run your business along with the peace of mind that all your equipment will last throughout its expected life. These services often offer guarantees as well as the flexibility in scheduling or maintenance for your convenience.Randell believes strongly in the products it manufactures and backs those products with one of the best warranties in the industry. We believe with the proper maintenance and use, you will realize a profitable return on your investment and years of satisfied service.SYMPTOM POSSIBLE CAUSE PROCEDUREUnit doesn't run 1. No power to unit 1. Plug in unit2. Temperature control turned off 2. Check temperature control3. Temperature control faulty 3. Test temperature control4. Compressor overheated 4. Clean condenser coil5. Condenser fan faulty 5. Service condenser fan6. Overload protector faulty 6. Test overload7. Compressor relay faulty 7. Test relay8. Defrost timer faulty 8. Test defrost timer9. Compressor faulty 9. Call for service at 800-621-8561Unit short cycles 1. Condenser coil dirty 1. Clean coil2. Condenser fan faulty 2. Service fan and motor.3. Compressor faulty 3. Call for service at 800-621-85614. Overload repeatedly tripping 4. Check outlet voltageUnit runs constantly 1. Frost build-up 1. Defrost evaporator2. Drawer not sealing properly 2. Check drawer seal3. Drawer gasket damaged 3. Replace drawer gasket4. Condenser coil dirty 4. Clean coil5. Condenser fan faulty 5. Service condenser motorUnit not cold enough 1. Temperature control set toohigh 1. Adjust control to lower setting2. Temperature control faulty 2. Test control3. Condenser coil dirty 3. Clean coil4. Drawer not sealing properly 4. Check drawer seal5. Drawer gasket damaged 5. Replace drawer gasket6. Evaporator fan faulty 6. Service evaporator fan7. Evaporator iced up7. Defrost evaporator, test defrostheater, test thermodisc, test defrosttimer8. Refrigerant leaking orcontaminated 8. Call for service at 800-621-8561Unit too cold 1. Temperature control set too low 1. Adjust control to raise setting2. Temperature control faulty 2. Test controlUnit doesn’t defrost 1. Defrost heater faulty 1. Test defrost heater2. Defrost thermodisc faulty 2. Test thermodisc3. Defrost timer faulty 3. Test defrost timerMoisture around 1. Breaker strips faulty 1. Inspect stripsdrawer or frame2. Frame heater defective 2. Call for service at 800-621-85613. Temperature set too low 3. Raise temperature settingIce in drain pan orwater in bottom ofunit or floor 1. Drain tube clogged 1. Clean drain2. Unit not level 2. Adjust leveling leg/shim casters Unit noisy 1. Unit not level 1. Adjust leveling leg/shim casters2. Compressor mountings loose or hardened. 2. Tighten or replace compressor mountings3. Condenser fan damaged orhitting fan shroud 3. Inspect condenser fan 4. Evaporator fan damaged orhitting fan shroud 4. Inspect evaporator fan5. Mechanical compartment louver rattling 5. Bend or align tabs to reduce noise. Replace if necessary.ReplacementParts。
冷柜使用说明书
1.幅面为：140X 210mm ；
2.纸质：70g双胶纸。
谢国龙李平芳査淇舰
唐涛
2012.08.242012.08.242012.08.24
2012.08.24
2012.08.24
技 术 要 求
签 名日 期
设 计 审 核标准化审 定
会 签
批 准
冷柜使用说明书
文件编号: 50200105005W 文件名称: 说明书
日 期
签 名
1更改记录
235合肥华凌股份有限公司
胡亚洲版面内容排版更新，2012.09.10切换
谢国龙2012.08.20第四页将冷藏室改为冷藏室（微冻室）；冷藏室使用描述变更。
谢国龙2012.10.15说明书封底客服电话描述更改，2012.11.01切换
谢国龙2012.10.24BCD-221/271VMQ 冷媒注入量由30g 、改为g 、53g ，立即切换
30g 49谢国龙2013.02.274BCD-311VMQ 冷媒注入量由45g 改为63g ，2013.03.15切换谢国龙2013.02.186第四页冷藏室（微冻室）使用描述变更;消化库存后切换。
谢国龙2013.04.247说明书封底删除地址后“176号”及网址“.cn ”，删除非在产型号，产品执行标准更改，库存给予消化。
谢国龙2013.07.198增加型号BCD-201VMQ ，库存可用于BCD-221/271/311VMQ 消化。
谢国龙2014.02.249
更改型号BCD-201VMQ 额定电流
谢国龙
2014.03.06。
海尔 BC BD-103HTD 103升冷藏冷冻转换柜 使用说明书
产品外形尺寸示意图（单位：mm）：
型号 BC/BD-103HTD BC/BD-143HTD BC/BD-203HTD
宽深高 a 570 560 845 1330
720 560 845 1330
940 560 845 1330
深
注：1. 各系列型号产品的尺寸见技术数据。
2. 以上尺寸为参考尺寸，具体以实物测量为准。
体现海尔真诚、贴心的服务，海尔友情提醒您：
产品的安装服务，因用户的安装环境、个性需求不同，如需辅加材料或有特殊服务项目支付材料费， 具体付费请参照服务工程师出示的《服务收费指导价格标准手册》，请给予监督。 如服务工程师不按标准收费或服务规范执行不到位，请拨打海尔全国客服电话: 4006 999 999或登 录海尔自助服务专区评价、投诉。
请保持冷柜放置平稳，冷柜放置不平稳时会产生噪声。 请确保冷柜外表面没有接触其他物体或墙壁。
流水声：听到类似流水声或气泡咕噜声，是制冷剂流动时发出的声音，属于正常现象。 嗡嗡声：压缩机工作会产生“嗡嗡”声，启动或停止时声音较大，属于正常现象。 咔嗒声：冷柜在开停机时，启动继电器等元件由于动作发出的声音，属于正常现象。 啪啪声：冷柜工作时，由于温度的变化，导致蒸发器和管路因热胀冷缩发出的声音，属于正常现象。
类型 (I) 频率(Hz) (W) (kg/12h) (kW·h/y) (kW·h/24h) R600a 方式
dB(A)
外形尺寸 宽x深x高 （mm）
SN N ST T
103 220/50 70
5.5
153
0.38
45
Y 27
38
570X560X845
SN N ST T
143 220/50 80
海尔冷柜说明书
HRE/HFE-127B-_HD使用说明书是本产品不可分割的重要组成部分，用户须妥善保管。
请务必仔细阅读本使用说明书中描述的指南和警告事项，因为这些指南和警告事项中文I. 一般信息 (1)1.1...................................................................................................... )D H C -B 741-E R H (构结 ............. ..... 2. 附件...................................................................................................................................................1 3. 安装位置.. (1)4.2................................................................................................................................................... 装安 5. 层板和导轨 . (3)3...................................................................................................................... )准标(托板层和板层]a [3.................................................................................................................................... )制定(轨导 4................................................................................................................................. )制定(杆撑支 6. 电气连接.. (4)7.4........................................................................................................................................接连管水排 II. 操作说明 (5)1. 启动 ................................................................................................................................................5 2. 前板 ...................................................................................................................................................5 3. 柜内温度设置 (6)4. 框架加热器 ........................................................................................................................................6 5. 除霜 (6)6. 关机 ...................................................................................................................................................7 III. 保养和清洁说明 .. (7)1. 内部、外部、层板 .............................................................................................................................7 2. 空气过滤网 ........................................................................................................................................7 IV. 报修前 .. (8)1. 显示故障代码的故障 (8)2. 不显示故障代码的故障 .....................................................................................................................8 V. 废弃处理.................................................................................................................................................8 VII. 气候类型说明 (9)ENGLISHI. INSTALLATION INSTRUCTIONS (10)1. CONSTRUCTION (HRE-147B-SHD) .........................................................................................10 2. ACCESSORIES ..........................................................................................................................10 3. LOCATION .................................................................................................................................10 4. SET UP .......................................................................................................................................11 5. SHELF AND RAIL .......................................................................................................................12 21.................................................................................... )d r a d n a t s ( P I L C F L E H S D N A F L E H S ]a [ [b] RAIL (customized) .................................................................................................................12 [c] HANGER (customized) ..........................................................................................................13 6. ELECTRICAL CONNECTIONS .................................................................................................13 7. DRAIN CONNECTIONS .............................................................................................................13 II. OPERATING INSTRUCTIONS ........................................................................................................14 1. START UP ..................................................................................................................................14 2. FRONT PANEL ...........................................................................................................................15 3. CABINET TEMPERATURE SETTING .......................................................................................15 4. FRAME HEATER ........................................................................................................................16 5. DEFROST ...................................................................................................................................16 6. SHUT DOWN ..............................................................................................................................16 III. MAINTENANCE ...............................................................................................................................16 1. INTERIOR, EXTERIOR, SHELF .................................................................................................16 2. AIR FILTER ................................................................................................................................17 IV. BEFORE CALLING A SERVICE AGENT .........................................................................................17 1. TROUBLES WITH ERROR CODE INDICATION .......................................................................17 2. TROUBLES WITHOUT ERROR CODE INDICATION ...............................................................18 V. DISPOSAL .......................................................................................................................................18 VI. WARRANTY . (18)[b][c]VI. 保修 (9)警告请勿弄湿本产品或在潮湿环境下使用本产品。
多重温度葡萄酒冷藏柜使用说明书
安装说明书............................................................................................................................................................................................................第 12 页使用说明书...............................................................................................................................................................................................................第 2 页多重温度葡萄酒冷藏柜请在首次使用前阅读本使用说明书2冷藏柜描述LED 灯条）LED 灯条）目录废物处置说明 ...........................................................................2冷藏柜描述 ...............................................................................2安全指令和警告 ........................................................................3冷藏柜使用范围 ........................................................................3EPREL 数据库 ..........................................................................3气候类型 ...................................................................................4电气连接 ...................................................................................4运行和控制元件.........................................................................4启动与关闭冷藏柜 .....................................................................4温度设置 ...................................................................................5风扇 ..........................................................................................5门打开警告................................................................................5温度警告 ...................................................................................5设置模式 ...................................................................................6内部照明灯 ................................................................................7标签 .........................................................................................7通过活性炭过滤装置交换空气...................................................7安全锁.......................................................................................8储存示意图................................................................................8清洁 ..........................................................................................8故障 ..........................................................................................9停用冷藏柜................................................................................9质保条件 (10)安装说明书随附配件 .................................................................................12安装滤尘器..............................................................................12冷藏柜通风..............................................................................12冷藏柜尺寸..............................................................................13安装尺寸 .................................................................................13安装冷藏柜..............................................................................14更换门铰链 (16)废物处置说明冷藏柜含部分可再用材料，应当进行合理处置——不能简单地与未分类的家庭垃圾混合在一起。
中意冷藏柜说明书[001]
![中意冷藏柜说明书[001]](https://img.taocdn.com/s3/m/b2d6f94230b765ce0508763231126edb6e1a7653.png)
中意冷藏柜说明书中意冷藏柜说明书欢迎使用中意冷藏柜，这款多功能而实用的冷藏柜将为您的生活带来便利和舒适。
本说明书将详细介绍冷藏柜的使用方法、注意事项以及一些实用的技巧，希望能给您带来指导和帮助。
第一部分：冷藏柜的基本操作1. 开关操作：冷藏柜的开关位于机身侧面，将开关拨至ON（开启）位置以启动冷藏柜，拨至OFF（关闭）位置则可停止运行。
2. 温度调节：冷藏柜的温度调节按钮位于机身正面，您可以根据需要调节冷藏室的温度。
一般而言，将冷藏柜温度控制在2-8摄氏度之间即可保持食物的新鲜。
3. 灯光控制：冷藏柜内部装有照明灯，开关位于机身上方，通过按下灯光按钮，您可以方便地控制照明灯的开关状态，同时也有助于节能。
第二部分：冷藏柜的使用技巧1. 合理放置食物：为了保证冷藏柜的高效使用，建议将食物按照种类和大小进行归类，并采用密封的容器或食品袋进行包装，以免食物散发异味或气味相互传染。
2. 避免过度装载：冷藏柜容积有限，注意不要过度堆放食物，以免影响空气对流和降低冷藏效果。
3. 定期清洁：为了保持冷藏柜的卫生和正常运行，建议定期对冷藏柜进行清洁。
在清洁之前，请务必断开电源，并使用温和的清洁剂搭配柔软的布进行清洁，避免使用硬质清洁工具或腐蚀性物质。
4. 调节风扇位置：冷藏柜内部可能配备有风扇，建议将其正确放置在适当的位置，以保证冷气均匀分布并提高冷藏效果。
第三部分：安全使用冷藏柜的注意事项1. 电源安全：在使用和清洁冷藏柜时，请确保插头和电源线干燥，避免接触水分和潮湿环境，以防电气短路或触电事故发生。
2. 避免直接日光照射：为了保证冷藏柜的散热效果和正常使用寿命，请避免将冷藏柜暴露在直接阳光下，以及避免将冷藏柜放置在潮湿或高温的地方。
3. 维修和保养：为了保证冷藏柜的性能和安全运行，请避免任何未经授权的拆卸或维修。
如有故障或异常情况，请及时联系中意冷藏柜的售后服务，由专业技术人员进行处理。
感谢您选择中意冷藏柜，希望本说明书能够为您提供有用的信息和指导，让您在使用冷藏柜时更加方便、安全、舒心。
威廉士雪柜说明书
威廉士雪柜说明书威廉士雪柜说明书威廉士雪柜是一款先进的家电产品，旨在为用户提供高效、方便的冷藏和保鲜解决方案。
本说明书将为您详细介绍威廉士雪柜的使用方法、特点和维护保养等内容，帮助您充分利用该产品，享受愉快的冷藏体验。
一、使用方法1. 接通电源：在使用威廉士雪柜前，请确保正确接通电源，并确保供电电压符合产品标定要求。
2. 开机及温度设置：按下电源开关，威廉士雪柜将启动。
通过控制面板上的温度设置按钮，您可以根据需要来调整冷藏室和冷冻室的温度。
3. 分区设置：威廉士雪柜拥有适宜的分区设计，可根据食物储存需求进行灵活的分配。
将易变质食品放置在冷藏室，而冷冻室则适合储存肉类、海鲜等食物。
4. 适量储存：请勿过分堆积食物，保持适量储存有助于冷气流通，提升冷藏效果。
二、产品特点1. 高效制冷技术：威廉士雪柜采用先进的制冷技术，能够快速降低温度，保持食物的新鲜度和营养价值。
2. 智能控制系统：配备智能控制面板，方便用户根据需要调整温度和湿度，提供最佳的储存环境。
3. 多功能储藏：威廉士雪柜内部设计合理，可灵活调整储存空间，满足不同食物的储存需求。
4. 静音运行：威廉士雪柜运行时噪音极低，不会给您带来任何干扰，让您享受安静的生活环境。
三、维护保养1. 除霜清洁：定期进行除霜和清洁是保持威廉士雪柜良好状态的重要步骤。
请按照说明书上的方法进行操作。
2. 定期检查：定期检查产品的电源线、插头以及冷藏室和冷冻室的密封性能。
如发现异常状况，请及时联系售后服务。
3. 避免过载：避免超过威廉士雪柜的负荷量，避免堆放过多食物引起故障。
4. 食物储存：请注意将食物正确密封包装储存，避免异味扩散和交叉感染。
通过阅读本说明书，您已经了解到了如何正确使用、充分利用和维护威廉士雪柜的方法。
希望这些信息能够帮助您愉快地使用该产品，并为您的生活带来更多的便利和舒适！如有任何疑问或问题，请随时与我们联系，我们将竭诚为您提供服务。
澳柯玛PCD—196T冷藏冷冻柜使用说明书
澳柯玛PCD—196T冷藏冷冻柜使用说明书一、控制面板功能1、控制板上数字1~8只表示温度由高到低，不表示具体温度值，顺时针旋转温控旋钮，两室内温度将降低；逆时针旋转温控旋钮，两室内温度将升高。
2、红灯是运行灯，灯亮表示压缩机正在工作。
二、搬运、放置搬运1、冷柜应装在包装箱内运输，搬运时，箱体与地面之间倾角不大于45°。
2、冷柜搬运时从底部抬起，轻搬轻放。
放置1、冷柜放置时，必须去掉所有包装物，方可使用。
2、冷柜不可侧放和倒置，冷柜应放置平稳，以防产生振动和噪音。
3、冷柜应置于通风处，背后及两侧距墙壁应大于10厘米，以利于空气流通。
4、冷柜应远离热源，以免影响制冷效果。
5、冷柜应置于干燥处，以防止生锈和影响电气绝缘。
三、使用方法及注意事项使用前的准备1、为了您的使用安全，使用产品前必须去掉所有包装物。
2、开箱检查附件是否齐全，将箱内外擦拭干净，各附件放置到位。
3、接通电源后，进行检查，三十分钟后箱内温度有明显下降方可使用。
冷藏室使用1、冷藏室温度随温控旋钮的顺时针旋转将均匀降低，根据温度不同可用来冷藏、冰镇、微冻物品。
一般情况下，冷藏时建议温控旋钮置于3~5之间，冰镇、微冻时建议温控旋钮置于4~6之间，此时箱内温度可达0℃以下，冰镇、微冻物品时间不宜过长。
同时应根据环境温度、所贮存物品的温度要求及数量不同而调整温控旋钮，以达到最佳效果。
2、物品需冷藏时，因内胆后壁（标识面）温度较低，物品距内胆后壁应大于5厘米，以免冻结。
3、因存入物品及开门的影响，箱内会产生水份，使用时必须及时清除，避免影响物品贮存。
4、当使用的环境温度低于10℃时，冷藏室温度会很低，不宜再用来冷藏物品，使用时必须注意。
5、物品应用塑料袋包装好，可避免串味和水分蒸发。
6、注意：冷藏室储藏温度设计范围涵盖0℃以下，易结冰物品不宜隔夜或长时间存放，以免冻坏。
冷冻室使用1、应根据“冷藏室使用中1”要求、环境温度、所贮存物品的温度要求及数量不同而调整温控器旋钮，平常建议调至5~7位置。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
＊2.2冷藏柜显示温度与检测温度允许误差范围﹕±2℃。
3.注意事项及维护保养﹕
3.1保持冷藏柜表面及冷藏室内清洁。
3.2禁止随意调整温度调节旋钮。
3.3放置制冷物品时﹐尽量排放松散一些。
设备操作说明书第1页共1页
设备名称
冷藏柜
设备功能
冷藏物品
文件编号
设备型号
EB15m3L4D
厂商
中宝
版本
B0
1.操作说明﹕
1.1选择其相应电源220V 50Hz。
1.2打开冷藏柜电源开关。
1.3根据制冷温度要求﹐调整旋转钮至相应刻度﹐数字越大﹐制冷温度越低。
1.4将需冷藏之物品放置于冷藏室内。
2温度检测方法﹕
3.4制冷物品放入冷藏室前﹐必须包装完好﹐以免腐蚀冷藏室内零部件。
3.5冷凝器每月清洗一次﹐清洗时须拔下电源插头。
3.6当检测温度与冷藏柜的自显温度差异超过误差范围时﹐须及时通知相关人员处理。
核准
审核
制作
日期